GR-D240PAL.book Page 1 Wednesday, November 17, 2004 7:32 PM
Dear Customer,
Thank you for purchasing this digital
video camera. Before use, please
read the safety information and
precautions contained in the pages
product.
ENGLISH
DIGITAL VIDEO CAMERA
GETTING STARTED
GR-D240
VIDEO RECORDING &
PLAYBACK
Please visit our Homepage on the World Wide Web for
Digital Video Camera:
For Accessories:
ADVANCED FEATURES
REFERENCES
TERMS
To deactivate the demonstration,
set “DEMO MODE” to “OFF”.
INSTRUCTIONS
EN
LYT1380-001A
MasterPage: Start_Right
GR-D240PAL.book Page 3 Wednesday, November 17, 2004 7:32 PM
EN
3
SAFETY PRECAUTIONS
CAUTION:
IMPORTANT (for owners in the U.K.)
To avoid electric
Connection to the mains supply in the United
shock or damage to
Kingdom.
the unit, first firmly
insert the small end
DO NOT cut off the mains plug from this
equipment.
of the power cord into
the AC Adapter until it
is no longer wobbly,
and then plug the
larger end of the
power cord into an
AC outlet.
If the plug fitted is not suitable for the power
points in your home or the cable is too short to
reach a power point, then obtain an appropriate
safety approved extension lead or consult your
dealer.
BE SURE to replace the fuse only with an
identical approved type, as originally fitted,
and to replace the fuse cover.
CAUTIONS:
If nonetheless the mains plug is cut off be sure to
remove the fuse and dispose of the plug
immediately, to avoid possible shock hazard by
inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains
plug then follow the instructions given below:
DO NOT make any connection to the Larger
Terminal coded E or Green.
● This camcorder is designed to be used with
PAL-type colour television signals. It cannot be
used for playback with a television of a different
standard. However, live recording and LCD
monitor/viewfinder playback are possible
anywhere.
● This product includes patented and other
proprietary technology and will operate only
with JVC Data Battery. Use the JVC
BN-VF707U/VF714U/VF733U battery packs
and, to recharge them or to supply power to the
camcorder from an AC outlet, use the provided
multi-voltage AC Adapter. (An appropriate
conversion adapter may be necessary to
accommodate different designs of AC outlets in
different countries.)
The wires in the mains lead are coloured in
accordance with the following code:
Blue to N (Neutral)
or Black
Brown to L (Live)
or Red
If these colours do not correspond with the
terminal identifications of your plug, connect as
follows:
Blue wire to terminal coded N (Neutral) or
coloured black.
Brown wire to terminal coded L (Live) or coloured
Red.
If in doubt — consult a competent electrician.
Caution on Replaceable lithium battery
The battery used in this device may present a fire
or chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 100°C
or incinerate.
Replace battery with Panasonic (Matsushita
Electric), Sanyo, Sony or Maxell CR2025.
Danger of explosion or Risk of fire if the battery is
incorrectly replaced.
● Dispose of used battery promptly.
● Keep away from children.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
CAUTIONS:
● To prevent shock, do not open the cabinet. No
user serviceable parts inside. Refer servicing to
qualified personnel.
● When you are not using the AC Adapter for a
long period of time, it is recommended that you
disconnect the power cord from AC outlet.
● Do not disassemble and do not dispose of in
fire.
NOTES:
● The rating plate (serial number plate) and
safety caution are on the bottom and/or the
back of the main unit.
● The rating information and safety caution of the
AC Adapter are on its upper and lower sides.
MasterPage: Left
GR-D240PAL.book Page 4 Wednesday, November 17, 2004 7:32 PM
4
EN
SOME DO’S AND DON’TS ON THE SAFE USE
OF EQUIPMENT
This equipment has been designed and
manufactured to meet international safety
standards but, like any electrical equipment,
care must be taken if you are to obtain the
best results and safety is to be assured.
When the equipment is installed in a cabinet or on
a shelf, make sure that it has sufficient space on
all sides to allow for ventilation (10 cm or more on
both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not be able
to get out.)
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
DO read the operating instructions before you
attempt to use the equipment.
When discarding batteries, environmental
problems must be considered and the local rules
or laws governing the disposal of these batteries
must be followed strictly.
The apparatus shall not be exposed to dripping or
splashing.
Do not use this equipment in a bathroom or
places with water.
Also do not place any containers filled with water
or liquids (such as cosmetics or medicines, flower
vases, potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this
equipment, fire or electric shock may be caused.)
DO ensure that all electrical connections (including
the mains plug, extension leads and
interconnections between pieces of equipment) are
properly made and in accordance with the
manufacturer’s instructions. Switch off and withdraw
the mains plug when making or changing
connections.
DO consult your dealer if you are ever in doubt
about the installation, operation or safety of your
equipment.
DO be careful with glass panels or doors on
equipment.
DON’T continue to operate the equipment if you are
in any doubt about it working normally, or if it is
damaged in any way — switch off, withdraw the
mains plug and consult your dealer.
Do not point the lens or the viewfinder directly into
the sun. This can cause eye injuries, as well as
lead to the malfunctioning of internal circuitry.
There is also a risk of fire or electric shock.
DON’T remove any fixed cover as this may expose
dangerous voltages.
CAUTION!
The following notes concern possible physical
damage to the camcorder and to the user.
DON’T leave equipment switched on when it is
unattended unless it is specifically stated that it is
designed for unattended operation or has a standby
mode. Switch off using the switch on the equipment
and make sure that your family knows how to do
this. Special arrangements may need to be made
for infirm or handicapped people.
DON’T use equipment such as personal stereos or
radios so that you are distracted from the
requirements of road safety. It is illegal to watch
television whilst driving.
When carrying, be sure to always securely attach
and use the provided strap. Carrying or holding
the camcorder by the viewfinder and/or the LCD
monitor can result in dropping the unit, or in a
malfunction.
Take care not to get your finger caught in the
cassette holder cover. Do not let children operate
the camcorder, as they are particularly
susceptible to this type of injury.
DON’T listen to headphones at high volume, as
such use can permanently damage your hearing.
Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the camcorder.
DON’T obstruct the ventilation of the equipment, for
example with curtains or soft furnishings.
Overheating will cause damage and shorten the life
of the equipment.
DON’T use makeshift stands and NEVER fix legs
with wood screws — to ensure complete safety
always fit the manufacturer’s approved stand or legs
with the fixings provided according to the
instructions.
CAUTION!
Connecting cables (Audio/Video, S-Video, etc.) to
the camcorder and leaving it on top of the TV is
not recommended, as tripping on the cables will
cause the camcorder to fall, resulting in damage.
DON’T allow electrical equipment to be exposed to
rain or moisture.
ABOVE ALL
● NEVER let anyone especially children push
anything into holes, slots or any other opening in
the case — this could result in a fatal electrical
shock;
● NEVER guess or take chances with electrical
equipment of any kind — it is better to be safe
than sorry!
MasterPage: TOC_Heading0_Right
GR-D240PAL_03Toc.fm Page 5 Friday, November 19, 2004 4:10 PM
CONTENTS
EN
5
Loading/Unloading A Cassette ....................... 16
VIDEO RECORDING & PLAYBACK
17
Connections To A TV Or VCR........................ 21
MasterPage: Start_Right
GR-D240PAL.book Page 7 Wednesday, November 17, 2004 7:32 PM
GETTING STARTED
EN
7
Controls
Other Parts
Backlight Compensation Button [BACK
Speaker Volume Control [VOL. +, –]
Z Lens
a Camera Sensor
(Be careful not to cover this area, a sensor
necessary for shooting is built-in here.)
b Stereo Microphone
I Battery Release Button [PUSH BATT.]
M Cassette Open/Eject Switch [OPEN/EJECT]
Connectors
The connectors are located beneath the covers.
N S-Video/Audio/Video Output Connector [S/
P Digital Video Connector [DV OUT] (i.Link*)
(An optional microphone can be used during
video recording and audio dubbing. To
stabilise the microphone, use of an optional
shoe adapter is recommended.)
* i.Link refers to the IEEE1394-1995 industry
specification and extensions thereof. The logo
is used for products compliant with the i.Link
standard.
Indicators
MasterPage: Left
GR-D240PAL.book Page 8 Wednesday, November 17, 2004 7:32 PM
GETTING STARTED
8
EN
S Battery Remaining Power Indicator
U Brightness Control Indicator (LCD monitor/
LCD Monitor/Viewfinder Indications
During Video Recording
9
0 qwe
r
t
V Manual Focus Adjustment Indicator
1h40m
1
2
25
x
W
T
REC
y
3
4
5
6
7
u
i
BRIGHT
SOUND 12BIT
50m
o
10
.
11. 05
10: 00
15:55
8
d
s a
p
B
: Spot Exposure Control Indicator
: Backlight Compensation Indicator
D
E Selected Program AE With Special Effects
G SOUND 12BIT/16BIT: Sound Mode Indicator
after turning on the camcorder.)
: Auxiliary Microphone Level
Indicator
L
R
(Appears when an optional microphone is
K Selected Wipe/Fader Effect Indicator
(Rotates while tape is running.)
PAUSE: (Appears during Record-Standby
O: (Appears when taking Snapshot.)
Q 5S/Anim.: Displays the 5-Second Recording
mode or Animation recording mode.
MasterPage: Start_Right
GR-D240PAL.book Page 9 Wednesday, November 17, 2004 7:32 PM
GETTING STARTED
Before Using This Camcorder
EN
9
During Video Playback
1
2
3 4
Make sure you only use cassettes with the Mini
DV mark
.
12B I T / M I X
L
This camcorder is designed exclusively for the
digital video cassette. Only cassettes marked
“
” can be used with this unit.
BLANK SEARCH
PUSH "STOP" BUTTON
TO CANCEL
Remember that this camcorder is not
compatible with other digital video formats.
Remember that this camcorder is intended for
private consumer use only.
Any commercial use without proper permission is
prohibited. (Even if you record an event such as a
show, performance or exhibition for personal
enjoyment, it is strongly recommended that you
obtain permission beforehand.)
50m
VOLUME
5
1 0
.
11. 05
10: 0 0
20 : 21 : 25
8
7
6
D 4: Playback
5: Fast-Forward/Shuttle Search
3: Rewind/Shuttle Search
9: Pause
9 U: Forward Frame-By-Frame Playback/
Slow-Motion
Y 9: Reverse Frame-By-Frame Playback/
Slow-Motion
E Battery Remaining Power Indicator
BRIGHT: Brightness Control Indicator (LCD
Before recording important video, be sure to
make a trial recording.
Play back your trial recording to make sure the
video and audio have been recorded properly.
We recommend cleaning your video heads
before use.
If you haven’t used your camcorder for a while, the
heads may be dirty. We recommend periodically
cleaning the video heads with a cleaning cassette
(optional).
Be sure to store your cassette tapes and
camcorder in the proper environment.
Video heads can become dirty more easily if your
cassette tapes and camcorder are stored in a dusty
area. Cassette tapes should be removed from the
camcorder and stored in cassette cases. Store the
camcorder in a bag or other container.
Use SP (Standard) mode for important video
recordings.
LP (Long Play) mode lets you record 50% more
video than SP (Standard) mode, but you may
experience mosaic-like noise during playback
depending on the tape characteristics and the
usage environment.
So, for important recordings, we recommend using
SP mode.
It is recommended that you use JVC brand
cassette tapes.
Your camcorder is compatible with all brands of
commercially available cassette tapes complying
with the MiniDV standard, but JVC brand cassette
tapes are designed and optimized to maximize the
performance of your camcorder.
MasterPage: Left
GR-D240PAL.book Page 10 Wednesday, November 17, 2004 7:32 PM
GETTING STARTED
10
EN
How To Attach The Lens Cap
Provided Accessories
To protect the lens, attach
the provided lens cap to the
camcorder as shown in the
illustration.
NOTE:
OR
To confirm the lens cap is on
correctly make sure the cap is
flush to the camcorder.
Place here during
shooting.
a AC Adapter AP-V17E or AP-V14E
b Power Cord (only for AP-V14E)
c Battery Pack BN-VF707U
d S/AV Cable
e Cable Adapter
g Lens Cap (see the right column for
attachment)
NOTES:
● In order to maintain optimum performance of the
camcorder, provided cables may be equipped with
one or more core filter. If a cable has only one core
filter, the end that is closest to the filter should be
connected to the camcorder.
● Make sure to use the provided cables for
connections. Do not use any other cables.
MasterPage: Start_Right
GR-D240PAL.book Page 11 Wednesday, November 17, 2004 7:32 PM
GETTING STARTED
EN
11
How To Attach The Shoulder Strap
Follow the illustration.
Power
This camcorder’s 2-way power supply system
1 Thread the strap through the eyelet.
lets you choose the most appropriate source of
power. Do not use provided power supply units
with other equipment.
2 Fold it back and thread it through the strap
guide and the buckle.
● To adjust the length of the strap, loosen and then
tighten the strap in the buckle.
Charging The Battery Pack
3 Slide the strap guide fully towards the eyelet.
Power switch
Buckle
M
A
OFF PLAY
POWER/CHARGE lamp
POWER/
CHARGE
Strap guide
Battery pack mount
PUSH BATT.
2
Battery pack
Arrow
mark
To DC connector
Open the cover.
3
1
Eyelet
To AC outlet
AC Adapter (ex. AP-V17E)
1 Set the Power Switch to “OFF”.
2 With the arrow on the battery pack pointing
downward, push the battery pack slightly against
the battery pack mount a.
3 Slide down the battery pack until it locks in
place b.
4 Connect the AC Adapter to the camcorder.
5 Connect the Power Cord to the AC Adapter.
(AP-V14E only)
6 Plug the AC Adapter into an AC outlet. The
POWER/CHARGE lamp on the camcorder
blinks to indicate charging has started.
7 When the POWER/CHARGE lamp goes out,
charging is finished. Unplug the AC Adapter
from the AC outlet. Disconnect the AC Adapter
from the camcorder.
CONTINUED ON NEXT PAGE
MasterPage: Left
GR-D240PAL.book Page 12 Wednesday, November 17, 2004 7:32 PM
GETTING STARTED
12
EN
To detach the battery pack
Using The Battery Pack
Slide the battery pack upward while pressing
PUSH BATT. to detach it.
Battery pack
BN-VF707U*
Charging time
Approx. 1 hr. 30 min.
Approx. 2 hr. 40 min.
Approx. 5 hr. 40 min.
Maximum continuous recording time
LCD monitor
Battery pack
Viewfinder on
BN-VF714U
BN-VF733U
* Provided
on
BN-VF707U*
BN-VF714U
BN-VF733U
* Provided
NOTES:
1 hr. 5 min.
2 hr. 20 min.
5 hr. 25 min.
1 hr. 25 min.
3 hr.
NOTES:
7 hr. 5 min.
● It is recommended that only genuine JVC
batteries are used in this camcorder. Using
generic non-JVC batteries can cause damage to
the internal charging circuitry.
● Recording time is reduced significantly under the
following conditions:
● If the protective cap is attached to the battery
pack, remove it first.
● During charging, the camcorder cannot be
operated.
● Charging is not possible if the wrong type of
battery is used.
● When charging the battery pack for the first time
or after a long storage period, the POWER/
CHARGE lamp may not light. In this case, remove
the battery pack from the camcorder, then try
charging again.
● If the battery operation time remains extremely
short even after having been fully charged, the
battery is worn out and needs to be replaced.
Please purchase a new one.
• Zoom or Record-Standby mode is engaged
repeatedly.
• The LCD monitor is used repeatedly.
• The playback mode is engaged repeatedly.
● Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned shooting time.
ATTENTION:
Before detaching the power source, make sure that
the camcorder’s power is turned off. Failure to do so
can result in a camcorder malfunction.
Data Battery System
● Since the AC Adapter processes electricity
internally, it becomes warm during use. Be sure to
use it only in well-ventilated areas.
● Using the optional AA-VF7 Battery Charger, you
can charge the BN-VF707U/VF714U/VF733U
battery pack without the camcorder.
● After 5 minutes has elapsed in Record-Standby
mode with the cassette inserted, the camcorder
will automatically turn off its power supplied from
the AC adapter. In this case, the battery charge
starts if the battery is attached to the camcorder.
You can check the remaining battery power and
the recordable time.
1) Make sure the battery is attached and the
Power Switch is set to “OFF”.
2) Open the LCD monitor fully.
3) Press DATA, and the battery status screen
appears.
● It can be displayed on the viewfinder when the
LCD monitor is closed.
● It is displayed for 5 seconds if the button is
pressed and released quickly, and for 15
seconds if the button is pressed and hold for
several seconds.
● If “COMMUNICATION ERROR” appears
instead of the battery status even though you
tried to press DATA several times, there may
be a problem on the battery. In such a case,
consult your nearest JVC dealer.
MasterPage: Start_Right
GR-D240PAL.book Page 13 Wednesday, November 17, 2004 7:32 PM
GETTING STARTED
EN
13
Using AC Power
Operation Mode
To turn on the camcorder, set the Power Switch
to any operation mode except “OFF” while
pressing down the Lock Button located on the
switch.
NOTE:
The provided AC Adapter features automatic
voltage selection in the AC range from 110 V to
240 V.
Power Switch
MENU/DATA
Lock Button
About Batteries
DANGER! Do not attempt to take the batteries
apart, or expose them to flame or excessive
heat, as it may cause a fire or explosion.
WARNING! Do not allow the battery or its
terminals to come in contact with metals, as this
can result in a short circuit and possibly start a
fire.
M
A
POWER/
CHARGE
POWER/
CHARGE lamp
To resume the original function of the
accurate battery power indication
If the battery power indication differs from the
actual operating time, fully charge the battery,
and then run it down. However this function may
not turn back if the battery was used for a long
period of time under extremely high/low
temperature condition or charged too many
times.
Choose the appropriate operation mode
according to your preference using the Power
Switch.
Power Switch Position
A (Full Auto Recording):
Allows you to record using NO special effects
or manual adjustments. Suitable for standard
recording.
The “A” indicator appears on the display.
M (Manual Recording):
Allows you to set various recording functions
If you want more creative capabilities than Full
Auto Recording, try this mode.
OFF:
Allows you to switch off the camcorder.
PLAY:
● Allows you to play back a recording on the
tape.
● Allows you to set various playback functions
CONTINUED ON NEXT PAGE
MasterPage: Left
GR-D240PAL.book Page 14 Wednesday, November 17, 2004 7:32 PM
GETTING STARTED
14
EN
Power-Linked Operation
Date/Time Settings
The date/time is recorded onto the tape at all
times, but its display can be turned on or off
When the Power Switch is set to “A” or “M”, you
can also turn on/off the camcorder by opening/
closing the LCD monitor or pulling out/pushing in
the viewfinder.
INFORMATION:
on the left column.
The following explanations in this manual
supposes the use of LCD monitor in your
operation. If you want to use the viewfinder,
close the LCD monitor and pull out the
viewfinder fully.
2 Press + or – to select “CLOCK ADJ.”, and
press MENU. The parameter for “Day” is
highlighted.
CAMERA DISPLAY
3 Press + or – to input
the day, and press MENU.
Repeat to input the month,
year, hour and minute.
Language Settings
The language on the display can be changed.
CLOCK
ADJ .
20. 1 2. 0 5
3 0
1
7
:
4 Press + or – to select
“BRETURN”, and press
MENU twice. The Menu
Screen closes.
1 Set the Power Switch to “M” while pressing
down the Lock Button located on the switch.
Grip Adjustment
3 Press MENU. The Menu Screen appears.
CAMERA DISPLAY
4 Press + or – to select
1 Adjust the velcro strip.
BRIGHT
“n”, and press MENU.
ON SCREEN
DATE / T I ME
T I ME CODE
LANGUAGE
AUX M I C
CLOCK
–
–
–
–
–
LCD / TV
AUTO
2 Pass your right hand
through the loop and grasp
the grip.
The CAMERA DISPLAY
Menu appears.
OFF
ENGLISH
ON
20. 1 2. 0 5
1
ADJ .
7
:
3 0
5 Press + or – to select
“LANGUAGE”, and press
MENU.
3 Adjust your thumb and
fingers through the grip to
easily operate the
Recording Start/Stop
Button, Power Switch and
Power Zoom Lever. Be
RETURN
CAMERA DISPLAY
6 Press + or – to select
the desired language, and
press MENU.
LANGUAGE – ENGLISH
ESPAÑOL
7 Press + or – to select
“BRETURN”, and press
MENU twice. The Menu
Screen closes.
sure to fasten the velcro strip to your preference.
РУССКИЙ
MasterPage: Start_Right
GR-D240PAL.book Page 15 Wednesday, November 17, 2004 7:32 PM
GETTING STARTED
EN
15
Viewfinder Adjustment
1 Set the Power Switch to “A” or “M” while
pressing down the Lock Button located on the
switch.
Brightness Adjustment Of The
Display
1 Set the Power Switch
+
to “M” or “PLAY” while
–
2 Make sure the LCD monitor is closed and
locked. Pull out the viewfinder fully and adjust it
manually for best viewability.
pressing down the Lock
Button located on the
switch.
3 Turn the Dioptre Adjustment Control until the
indications in the viewfinder are clearly focused.
Example:
2 Open the LCD monitor
MENU
● To adjust the brightness of
the viewfinder, pull out the
viewfinder fully and set
“PRIORITY” to “FINDER”
BRIGHT
3 Press MENU. The
Menu Screen appears.
4 Press + or – to select “n”, and press MENU.
PAUSE
The CAMERA DISPLAY Menu appears.
5 Press + or – to select “BRIGHT”, and press
MENU. The Menu Screen closes and the
brightness control indicator appears.
Dioptre Adjustment Control
6 Press + or – until the appropriate brightness
CAUTION:
is reached.
When retracting the viewfinder, take care not to
pinch your fingers.
7 Press MENU to clear the brightness control
indicator from the display.
Tripod Mounting
To attach the camcorder
to a tripod, align the
direction stud and screw
to the mounting socket
and stud hole on the
camcorder. Then tighten
the screw clockwise.
● Some tripods are not
equipped with studs.
MasterPage: Left
GR-D240PAL.book Page 16 Wednesday, November 17, 2004 7:32 PM
GETTING STARTED
16
EN
NOTES:
Loading/Unloading A Cassette
● If you wait a few seconds and the cassette holder
does not open, close the cassette holder cover
and try again. If the cassette holder still does not
open, turn the camcorder off then on again.
● If the tape does not load properly, open the
cassette holder cover fully and remove the
cassette. A few minutes later, insert it again.
● When the camcorder is suddenly moved from a
cold place to a warm environment, wait a short
time before opening the cassette holder cover.
The camcorder needs to be powered up to load
or eject a cassette.
Cassette holder
Cassette holder
cover
PUSH HERE
Erase
protection tab
OPEN/EJECT
Make sure the window side
is facing out.
1 Slide and hold OPEN/EJECT in the direction
of the arrow, then pull the cassette holder cover
open until it locks. The cassette holder opens
automatically.
● Do not touch internal components.
2 Insert or remove a tape and press “PUSH
HERE” to close the cassette holder.
● Be sure to press only the section labelled “PUSH
HERE” to close the cassette holder; touching
other parts may cause your finger to get caught in
the cassette holder, resulting in injury or product
damage.
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.
● When the battery pack’s charge is low, you may
not be able to close the cassette holder cover. Do
not apply force. Replace the battery pack with a
fully charged one or use AC power before
continuing.
3 Close the cassette holder cover firmly until it
locks into place.
To protect valuable recordings
Slide the erase protection tab on the back of the
tape in the direction of “SAVE”. This prevents the
tape from being recorded over. To record on this
tape, slide the tab back to “REC” before loading
it.
MasterPage: Video_Heading0_Right
GR-D240PAL.book Page 17 Wednesday, November 17, 2004 7:32 PM
VIDEO RECORDING
EN
17
Tape Remaining Time
Approximate tape remaining
Basic Recording
time appears on the display.
“– h – – m” means the
camcorder is calculating the
remaining time. When the
remaining time reaches 2 minutes, the indication
starts blinking.
● The time required to calculate and display the
remaining tape length, and the accuracy of the
calculation, may vary according to the type of tape
used.
NOTE:
Before continuing, perform the procedures listed
below:
Power Zoom Lever
Power Switch
Lock Button
POWER/CHARGE Lamp
Recording Start/Stop Button
2 Open the LCD monitor fully.
3 Set the Power Switch to “A” or “M” while
pressing down the Lock Button located on the
switch.
● The POWER/CHARGE lamp lights and the
camcorder enters the Record-Standby mode.
“PAUSE” is displayed.
4 To start recording, press the Recording Start/
Stop Button. “T REC” appears on the display
while recording is in progress.
5 To stop recording, press the Recording Start/
Stop Button again. The camcorder re-enters the
Record-Standby mode.
Approximate recording time
Recording mode
Tape
SP
LP
45 min.
30 min.
60 min.
80 min.
30 min.
60 min.
80 min.
90 min.
120 min.
NOTES:
● If the Record-Standby mode continues for
5 minutes, the camcorder’s power shuts off
automatically. To turn the camcorder on again,
push back and pull out the viewfinder again or
close and re-open the LCD monitor.
● When a blank portion is left between recorded
scenes on the tape, the time code is interrupted
and errors may occur when editing the tape. To
avoid this, refer to “Recording From The Middle Of
MasterPage: Left
GR-D240PAL_05Video.fm Page 18 Friday, November 19, 2004 4:11 PM
VIDEO RECORDING
18
EN
LCD Monitor And Viewfinder
Zooming
While using the LCD monitor:
Produces the zoom in/out effect, or an
Make sure the viewfinder is pushed back in. Pull instantaneous change in image magnification.
on the end
LCD monitor fully. It can rotate 270° (90°
downward, 180° upward).
of the LCD monitor and open the
Zoom In
Slide the Power Zoom Lever towards “T”.
Zoom Out
While using the viewfinder:
Make sure the LCD monitor is closed and
locked. Pull out the viewfinder fully.
Slide the Power Zoom Lever towards “W”.
● The further you slide the Power Zoom Lever, the
quicker the zoom action.
180˚
Zoom in (T: Telephoto)
1
x
W
T
10
x
W
T
20
xW
T
40
xW
T
90˚
NOTES:
Zoom out (W: Wide angle)
● The image will not appear simultaneously on the
LCD monitor and the viewfinder. When the
viewfinder is pulled out while the LCD monitor is
opened, you can select which one to use. Set
“PRIORITY” to the desired mode in SYSTEM
10
x
W
T
Digital zoom zone
25X (optical) zoom zone
Approximate zoom ratio
● Coloured bright spots may appear all over the
LCD monitor or the viewfinder. However, this is not
NOTES:
● Focusing may become unstable during Zooming.
In this case, set the zoom while in Record-
Standby, lock the focus by using the manual focus
● Zooming is possible to a maximum of 800X, or it
can be switched to 25X magnification using the
● Zoom magnification of over 25X is done through
Digital image processing, and is therefore called
Digital Zoom.
● During Digital zoom, the quality of image may
suffer.
● Macro shooting (as close as approx. 5 cm to the
subject) is possible when the Power Zoom Lever
is set all the way to “W”. Also see “TELE MACRO”
in MANUAL Menu on page 24.
● When shooting a subject close to the lens, zoom
out first. If zoomed-in in the auto focus mode, the
camcorder may automatically zoom out
depending on the distance between the
camcorder and the subject. This will not occur
MasterPage: Start_Right
GR-D240PAL.book Page 19 Wednesday, November 17, 2004 7:32 PM
VIDEO RECORDING
EN
19
Journalistic Shooting
NOTES:
● The time code cannot be reset.
In some situations,
different shooting
angles may provide
more dramatic results.
Hold the camcorder in
the desired position
and tilt the LCD
monitor in the most
convenient direction. It
can rotate 270° (90°
downward, 180°
● During fast-forwarding and rewinding, the time
code indication does not move smoothly.
● The time code is displayed only when “TIME
Quick Review
Enables to check the end of the last recording.
1) Press
mode.
2) Tape is rewound for about several seconds
and played back automatically, then pauses in
the Recording-Standby mode for the next shot.
● Distortion may occur at start of playback. This is
normal.
during the Recording-Standby
upward).
Time Code
During recording, a time code is recorded on the
tape. This code is to confirm the location of the
recorded scene on the tape during playback.
Display
Recording From The Middle Of A Tape
1) Play back a tape or use Blank Search
start recording, then engage the Still Playback
Minutes
Seconds
2) Set the Power Switch to “A” or “M” while
pressing down the Lock Button located on the
switch, then start recording.
Frames*
(25 frames = 1 second)
12 : 34 : 24
* Frames are not displayed during recording.
If recording starts from a blank portion, the time
code begins counting from “00:00:00”
(minute:second:frame). If recording starts from
the end of a previously recorded scene, the time
code continues from the last time code number.
If during recording a blank portion is left partway
through the tape, the time code is interrupted.
When recording is resumed, the time code starts
counting up again from “00:00:00”. This means
the camcorder may record the same time codes
as those existing in a previously recorded scene.
cases;
● When shooting again after playing back a
recorded tape.
● When power shuts off during shooting.
● When a tape is removed and re-inserted during
shooting.
● When shooting using a partially recorded tape.
● When shooting on a blank portion located partway
through the tape.
● When shooting again after shooting a scene then
opening/closing the cassette holder cover.
MasterPage: Left
GR-D240PAL.book Page 20 Wednesday, November 17, 2004 7:32 PM
VIDEO PLAYBACK
20
EN
Shuttle Search
Allows high-speed search in either direction
during video playback.
1) During playback, press 5 for forward
search, or 3 for reverse search.
2) To resume normal playback, press 4/9.
● During playback, press and hold 5 or 3. The
search continues as long as you hold the button.
Once you release the button, normal playback
resumes.
Normal Playback
5
VOL. +/–
Lock Button
3
4/9
8
M
A
Speaker
Power
Switch
● A slight mosaic effect appears on the display
during Shuttle Search. This is not a malfunction.
MENU
ATTENTION:
During Shuttle Search, parts
of the picture may not be
clearly visible, particularly on
the left side of the screen.
2 Set the Power Switch to “PLAY” while
pressing down the Lock Button located on the
switch.
3 To start playback, press 4/9.
4 To stop playback, press 8.
● During Stop mode, press 3 to rewind, or 5
to fast-forward the tape.
Blank Search
Helps you find where you should start recording
in the middle of a tape to avoid time code
To control the speaker volume
Slide the Power Zoom Lever (VOL. +/–) towards
“+” to turn up the volume, or towards “–” to turn
down the volume.
NOTES:
2 Set the Power Switch to “PLAY” while
pressing down the Lock Button located on the
switch.
● The playback picture can be viewed in the LCD
monitor, viewfinder or on a connected TV.
3 Press MENU. The Menu Screen appears.
● If Stop mode continues for 5 minutes when power
is supplied from a battery, the camcorder shuts off
automatically. To turn on again, set the Power
Switch to “OFF”, then to “PLAY”.
● When a cable is connected to the S/AV connector,
the sound is not heard from the speaker.
4 Press MENU to select “t”. The VIDEO
Menu appears.
5 Press + or – to select “BLANK SRCH”, and
press MENU. The Sub Menu appears.
6 Press + or – to select “EXECUTE”, and press
Still Playback
MENU.
● The “BLANK SEARCH” indication appears and
the camcorder automatically starts reverse or
forward search, then stops at the spot which is
about 3 seconds of tape before the beginning of
the detected blank portion.
Pauses during video playback.
1) Press 4/9 during playback.
2) To resume normal playback, press 4/9
again.
● If still playback continues for more than about
3 minutes, the camcorder’s Stop mode is
automatically engaged.
● To cancel Blank Search midway, press 8.
NOTES:
● Before starting Blank Search, if the current
position is at a blank portion, the camcorder
searches in the reverse direction. If the current
position is at a recorded portion, the camcorder
searches in the forward direction.
● If the beginning or end of the tape is reached
during Blank Search, the camcorder stops
automatically.
● A blank portion which is shorter than 5 seconds of
tape may not be detected.
MasterPage: Start_Right
GR-D240PAL.book Page 21 Wednesday, November 17, 2004 7:32 PM
VIDEO PLAYBACK
EN
21
● The detected blank portion may be located
1 Make sure all units are turned off.
between recorded scenes. Before you start
recording, make sure there is no recorded scene
after the blank portion.
2 Connect the camcorder to a TV or VCR as
shown in the illustration.
Connections To A TV Or VCR
3 Connect the VCR output to the TV input,
referring to your VCR’s instruction manual.
4 Turn on the camcorder, the VCR and the TV.
5 Set the VCR to its AUX input mode, and set
the TV to its VIDEO mode.
To AV
To choose whether or not the following
displays appear on the connected TV
● Date/Time
connector
Open the cover.
S/AV cable
(provided)
mark
Set “DATE/TIME” to “AUTO”, “ON” or “OFF”.
● Time Code
Set “TIME CODE” to “ON” or “OFF”.
1
2
3
4
● Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/TV”.
“Y/C”/“CVBS”
Video Out Select
Switch
Cable
Adapter*
NOTES:
To TV or VCR
● It is recommended to use the AC Adapter as
the power supply instead of the battery pack.
TV
● To monitor the picture and sound from the
camcorder without inserting a tape, set the
camcorder’s Power Switch to “A” or “M”, then set
your TV to the appropriate input mode.
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound
when the camcorder is turned on.
VCR
A Black to S-VIDEO IN (Connect when your TV/
VCR has S-VIDEO IN and A/V input
connectors. In this case, it is not necessary to
connect the yellow video cable.)
B Yellow to VIDEO IN (Connect when your TV/
VCR has only A/V input connectors.)
C Red to AUDIO R IN**
D White to AUDIO L IN**
*
If your VCR has a SCART connector, use the
provided cable adapter.
** Not required for watching still images only.
NOTE:
Set the video out select switch of the cable adapter
as required:
Y/C: When connecting to a TV or VCR which
accepts Y/C signals and uses an S-Video cable.
CVBS: When connecting to a TV or VCR which
does not accept Y/C signals and uses an audio/
video cable.
MasterPage: Heading0_Left
GR-D240PAL.book Page 22 Wednesday, November 17, 2004 7:32 PM
MENUS FOR DETAILED ADJUSTMENT
EN
22
Menus without Sub Menus
Changing The Menu Settings
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of
the more detailed camcorder settings.
v WIPE/FADER
Selected menu icon
blinks.
r PROGRAM AE
p EXPOSURE
u W. BALANCE
Selected
parameter
PROGRAM AE
–
Lock Button
SPORTS
SNOW
+
SPOTLIGHT
TWILIGHT
SEPIA
MONOTONE
M
A
CLASSIC FILM
1) Press + or – to select
the desired parameter.
● Example: r PROGRAM
AE Menu
STROBE
Power Switch
2) Press MENU. Selection is complete. The
Menu Screen returns.
● Repeat the procedure if you wish to set other
function menus.
3) Press MENU. The Menu Screen closes.
MENU
1 For Video Recording Menus:
Menus with Sub Menus
q MANUAL
Set the Power Switch to “M” while pressing
down the Lock Button located on the switch.
Selected menu icon
blinks.
For Video Playback Menus:
Set the Power Switch to “PLAY” while pressing
down the Lock Button located on the switch.
Selected function
n CAMERA DISPLAY
n VIDEO DISPLAY
1) Press + or – to select
the desired function,
and press MENU. The
Sub Menu appears.
● Example: m CAMERA
Menu
2) Press + or – to select
the desired parameter.
3) Press MENU.
CAMERA
REC MODE
–
SOUND MODE– 1 2B I T
ZOOM
SNAP SHOT
GA I N UP
–
–
–
2 5 x
3 Press MENU. The Menu Screen appears.
FULL
AGC
4 Press + or – to select the desired function,
and press MENU. The selected function menu
appears.
RETURN
Screen for Video
Recording Menu
Screen for Video
Playback Menu
Sub Menu
WI PE / FADER
OFF
V I DEO
CAMERA
SOUND MODE– STEREO
REC MODE
–
FADER–WH I TE
FADER–BLACK
FADER–B .W
WI PE–CORNER
WI PE–WI NDOW
WI PE–SL I DE
WI PE–DOOR
WI PE–SCROLL
WI PE–SHUTTER
NARRAT I ON
REC MODE
–
–
OFF
BLANK SRCH
RETURN
Selection is complete.
● Repeat the procedure if
you wish to set other
function menus.
4) Press MENU. The
Menu Screen returns.
● Repeat the procedure if
you wish to set other
function menus.
5 Setting procedure hereafter depends on the
CAMERA
REC MODE
–
selected function.
SOUND MODE– 1 2B I T
ZOOM
–
–
–
2 5 x
SNAP SHOT
GA I N UP
FULL
AGC
RETURN
5) Press MENU. The Menu Screen closes.
MasterPage: Start_Right
GR-D240PAL.book Page 23 Wednesday, November 17, 2004 7:32 PM
MENUS FOR DETAILED ADJUSTMENT
EN
23
SNAP SHOT
Recording Menus
[FULL]: Snapshot mode with no frame
NEGA: Nega mode
PIN-UP: Pin-Up mode
CAMERA
The “m CAMERA” settings are effective when
the Power Switch is set to both “A” and “M”.
However, the menu settings can be changed
only when the Power Switch is set to “M”.
[ ] = Factory-preset
FRAME: Snapshot mode with frame
[FULL]
NEGA
PIN-UP
FRAME
REC MODE
For details on the procedure, refer to “Snapshot
[SP]: To record in the SP (Standard Play) mode
LP: Long Play—more economical, providing 1.5
times the recording time.
GAIN UP
OFF: Allows you to shoot dark scenes with no
picture brightness adjustment.
[AGC]: The overall appearance may be grainy,
NOTES:
● If the recording mode is switched, the playback
picture will be blurred at the switching point.
● It is recommended that tapes recorded in the LP
mode on this camcorder be played back on this
camcorder.
but the image is bright.
AUTO
: The shutter speed is automatically
adjusted. Shooting a subject in low or poor
lighting at slow shutter speed provides a brighter
image than in the AGC mode, but the subject’s
movements are not smooth or natural. The
overall appearance may be grainy. While the
shutter speed is being automatically adjusted,
● During playback of a tape recorded on another
camcorder, blocks of noise may appear or there
may be momentary pauses in the sound.
SOUND MODE
“
” is displayed.
[12BIT]: Enables video recording of stereo
sound on four separate channels, and is
recommended for use when performing Audio
Dubbing. (Equivalent to the 32 kHz mode of
previous models)
16BIT: Enables video recording of stereo sound
on two separate channels. (Equivalent to the
48 kHz mode of previous models)
ZOOM
25X: When set to “25X” while using digital zoom,
the zoom magnification will reset to 25X since
digital zoom will be disengaged.
[100X]: Allows you to use the Digital Zoom. By
digitally processing and magnifying images,
zooming is possible from 25X (the optical zoom
limit), to a maximum of 100X digital
magnification.
800X: Allows you to use the Digital Zoom. By
digitally processing and magnifying images,
zooming is possible from 25X (the optical zoom
limit), to a maximum of 800X digital
magnification.
MasterPage: Left
GR-D240PAL.book Page 24 Wednesday, November 17, 2004 7:32 PM
MENUS FOR DETAILED ADJUSTMENT
EN
24
MANUAL
WIDE MODE
[OFF]: Records with no change in the screen
ratio. For playback on a TV with a normal screen
ratio.
The “q MANUAL” settings are effective only
when the Power Switch is set to “M”.
[ ] = Factory-preset
CINEMA : Inserts black bands at the top and
DIS
bottom of the screen. The
indicator appears.
During playback on wide-screen TVs, the black
bands at the top and bottom of the screen are
cut and the screen ratio becomes 16:9. When
using this mode, refer to your wide-screen TV’s
instruction manual. During playback/recording
on 4:3 TVs/LCD monitor/viewfinder, black bands
are inserted at the top and bottom of the screen
and the image appears like a letter boxed 16:9
movie.
SQUEEZE : For playback on TVs with an
aspect ratio of 16:9. Naturally expands the
image to fit the screen without distortion. The
indicator appears. When using this mode,
refer to your wide-screen TV’s instruction
manual. During playback/recording on 4:3 TVs/
LCD monitor/viewfinder, the image is elongated
vertically.
OFF: Disables the function.
[ON
]: To compensate for unstable images
caused by camera-shake, particularly at high
magnification.
NOTES:
● Accurate stabilisation may not be possible if hand
shake is excessive, or depending on the shooting
condition.
● The “
” indicator blinks or goes out if the
Stabiliser cannot be used.
● Switch off this mode when recording with the
camcorder on a tripod.
5S
[OFF]: Disables 5-Second Recording.
Anim.: Allows you to record a few frames only.
By using an inanimate object and changing its
position between shots, you can record the
subject as though it is moving.
WIND CUT
[OFF]: Disengages the function.
ON
wind. The “
the sound will change. This is normal.
: Helps cut down on noise created by
” indicator appears. The quality of
TELE MACRO
[OFF]: Disables the function.
ON: When the distance to the subject is less
than 1 m, set “TELE MACRO” to “ON”. You can
shoot a subject as large as possible at a
distance of approx. 40 cm.
NOTE:
Depending on the zoom position, the lens may go out
of focus.
MasterPage: Start_Right
GR-D240PAL.book Page 25 Wednesday, November 17, 2004 7:32 PM
MENUS FOR DETAILED ADJUSTMENT
EN
25
SYSTEM
PRIORITY
[LCD]: The image is displayed on the LCD
monitor when the viewfinder is pulled out while
the LCD monitor is opened.
FINDER: The image is displayed in the
viewfinder when the viewfinder is pulled out
while the LCD monitor is opened.
The “s SYSTEM” functions which are set when
the Power Switch is set to “M” are also applied
when the Power Switch is set to “PLAY”.
[ ] = Factory-preset
BEEP
OFF: Even though not heard while shooting,
shutter sound is recorded on the tape.
BEEP: The beep sounds when the power is
turned on or off, and at the beginning and end of
recording. It also activates the shutter sound
CAM RESET
EXECUTE: Resets all settings to the factory-
preset.
[RETURN]: Does not reset all settings to the
factory-preset.
[MELODY]: Instead of a beep, a melody sounds
when any operation is performed. It also
REMOTE
OFF: Disables the remote control operations.
[ON]: Enables the remote control operations.
It is recommended that this function be set to
“OFF” to prevent improper operation.
DEMO MODE
OFF: Automatic demonstration will not take
place.
[ON]: Demonstrates certain functions such as
Program AE with special effects, etc., and can
be used to confirm how these functions operate.
Demonstration starts in the following cases:
● When the Menu Screen is closed after “DEMO
MODE” is turned “ON”.
● With “DEMO MODE” set to “ON”, if there is no
operation for about 3 minutes after the Power
Switch is set to “A” or “M”.
● Performing any operation during the
demonstration stops the demonstration
temporarily. If no operation is performed for more
than 3 minutes after that, the demonstration will
resume.
NOTES:
● If a cassette is in the camcorder, the
demonstration cannot be turned on.
● “DEMO MODE” remains “ON” even if the
camcorder power is turned off.
● If “DEMO MODE” remains “ON”, some functions
will not be available. After viewing demo, set to
“OFF”.
MasterPage: Left
GR-D240PAL.book Page 26 Wednesday, November 17, 2004 7:32 PM
MENUS FOR DETAILED ADJUSTMENT
EN
26
CAMERA DISPLAY
Playback Menus
● The “n” (CAMERA DISPLAY) settings are
effective even when the Power Switch is set to
“A”. However, the menu settings can be changed
only when the Power Switch is set to “M”.
● The “n” (CAMERA DISPLAY) settings except
“BRIGHT” and “AUX MIC” are effective only for
shooting.
VIDEO
[ ] = Factory-preset
SOUND MODE and NARRATION
During tape playback, the camcorder detects the
sound mode in which the recording was made,
and plays the sound back. Select the type of
sound to accompany your playback picture.
According to the menu access explanation on
[ ] = Factory-preset
BRIGHT
“NARRATION” from the Menu Screen and set it
to the desired parameter.
ON SCREEN
LCD: Keeps the camcorder’s display (except the
date, time and time code) from appearing on the
connected TV screen.
[LCD/TV]: Makes the camcorder’s display
appear on screen when the camcorder is
connected to a TV.
SOUND MODE
[STEREO
]: Sound is output on both “L” and
“R” channels in stereo.
SOUND L : Sound from the “L” channel is
output.
SOUND R : Sound from the “R” channel is
output.
DATE/TIME
OFF: The date/time does not appear.
[AUTO]: Displays the date/time for approx. 5
seconds when the Power Switch is set from
“OFF” to “A” or “M”.
NARRATION
[OFF]: Original sound is output on both “L” and
“R” channels in stereo.
ON: Dubbed sound is output on both “L” and “R”
channels in stereo.
ON: The date/time is always displayed.
MIX: Original and dubbed sounds are combined
and output in stereo on both “L” and “R”
channels.
TIME CODE
[OFF]: Time code is not displayed.
ON: Time code is displayed on the camcorder
and on the connected TV. Frame numbers are
REC MODE
[SP] / LP
Allows you to set the video recording mode (SP
or LP) depending on your preference. It is
recommended you use “REC MODE” in VIDEO
Menu when using this camcorder as a recorder
LANGUAGE
[ENGLISH] / ESPAÑOL / РУССКИЙ
The language setting can be changed.
BLANK SRCH
AUX MIC
OFF: Auxiliary microphone level indicator does
not appear.
[ON]: Displays auxiliary microphone level
indicator when optional microphone is
SYSTEM
Each setting is linked with “s SYSTEM”, which
appears when the Power Switch is set to “M”.
● The parameters are the same as in the
CLOCK ADJ.
MasterPage: Start_Right
GR-D240PAL.book Page 27 Wednesday, November 17, 2004 7:32 PM
MENUS FOR DETAILED ADJUSTMENT
EN
27
VIDEO DISPLAY
The “n” (VIDEO DISPLAY) settings are
effective only for video playback except
“BRIGHT” and “AUX MIC”.
● The parameters (except “OFF” in ON SCREEN
settings) are the same as in the description
[ ] = Factory-preset
BRIGHT
ON SCREEN
OFF / [LCD] / LCD/TV
When set to “OFF”, the camcorder’s display
disappears.
DATE/TIME
[OFF] / AUTO / ON
When set to “AUTO”, the date/time are displayed
in the following cases:
● When playback starts. The camcorder displays
the date/time when scenes are recorded.
● When the date is changed during playback.
TIME CODE
[OFF] / ON
LANGUAGE
[ENGLISH] / ESPAÑOL / РУССКИЙ
The language setting can be changed.
AUX MIC
OFF / [ON]
MasterPage: Heading0_Left
GR-D240PAL.book Page 28 Wednesday, November 17, 2004 7:32 PM
FEATURES FOR RECORDING
28
EN
5-Second Recording
Record a vacation or an important event in 5-
second clips to keep the action moving. This
function is available only for video recording.
Night-Scope
Makes dark subjects or areas even brighter than
they would be under good natural lighting.
Although the recorded image is not grainy, it may
look as if it is strobing due to the slow shutter
speed.
● The “5S” indicator appears.
1 Set the Power Switch to “M”.
2 Press the Recording Start/Stop Button to
start recording, and after 5 seconds the
camcorder enters Record-Standby mode
automatically.
● Even if you press the Recording Start/Stop Button
again within 5 seconds after recording starts,
Record-Standby mode is not engaged.
2 Press NIGHT so that the Night-Scope
indicator “
” appears.
● The shutter speed is automatically adjusted to
provide up to 25 times sensitivity.
● “ ” appears beside “
” while the shutter speed
is being automatically adjusted.
To take a snapshot in the 5-second recording
mode
To deactivate Night-Scope
Press NIGHT again so that the Night-Scope
indicator disappears.
Instead of pressing the Recording Start/Stop
SNAPSHOT. The camcorder records a 5-
second still. When “5S” is set to “Anim.”, this
function is not available.
NOTES:
● During Night-Scope, the following functions or
settings cannot be activated and its indicator
blinks or goes out:
● During Night-Scope, it may be difficult to bring the
camcorder into focus. To prevent this, use of a
tripod is recommended.
NOTE:
When “5S” is set to “Anim.”, the 5-Second
Recording mode is not available. Animation
recording of a few frames only is taken instead.
MasterPage: Start_Right
GR-D240PAL.book Page 29 Wednesday, November 17, 2004 7:32 PM
FEATURES FOR RECORDING
EN
29
Snapshot (For Video Recording)
Manual Focus
This feature lets you record still images that look The camcorder’s Full Range AF system offers
like photographs onto a tape.
continuous shooting ability from close-up (as
close as approx. 5 cm to the subject) to infinity.
However, correct focus may not be obtained
depending on the shooting condition. In this
case, use the manual focus mode.
1 Set the Power Switch to “M”.
2 Set “SNAP SHOT” to the desired mode.
3 Press SNAPSHOT.
1 Set the Power Switch to
● There is the sound effect of a shutter closing.
● The “O” indication appears and a still image
will be recorded for approx. 6 seconds, then the
camcorder re-enters the Record-Standby mode.
● You can perform Snapshot also during recording.
A still image will be recorded for approx.
6 seconds, then the normal recording resumes.
● Regardless of the Power Switch position (“A” or
“M”), Snapshot recording takes place using the
selected Snapshot mode.
“M”.
2 Press FOCUS. The
manual focus indicator
appears.
3 Press + or – to focus on
a subject.
Manual focus
indicator
● When the focus level
cannot be adjusted any
further or closer, “ ” or “ ” will blink.
4 Press MENU. Focus adjustment is complete.
Motor Drive Mode
an effect similar to serial photography. (Interval
between still images: approx. 1 second)
To reset to Auto Focus
Press FOCUS twice or set the Power Switch to
“A”.
Manual focus is recommended in situations
listed below.
● When two subjects overlap in the same scene.
● When illumination is low.*
● When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-
colour wall, or a clear, blue sky.*
● When a dark object is barely visible in the LCD
monitor or the viewfinder.*
● When the scene contains minute patterns or
identical patterns that are regularly repeated.
● When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
● When shooting a scene with a high-contrast
background.
* The following low-contrast warnings appear
blinking:
,
,
and
.
MasterPage: Left
GR-D240PAL.book Page 30 Wednesday, November 17, 2004 7:32 PM
FEATURES FOR RECORDING
30
EN
Exposure Control
Iris Lock
Manual exposure control is recommended in the Like the pupil of the human eye, the iris
following situations:
● When shooting using reverse lighting or when the
background is too bright.
● When shooting on a reflective natural background
such as at the beach or when skiing.
● When the background is overly dark or the subject
is bright.
contracts in well-lit environments to keep too
much light from entering, and dilates in dim
environments to allow in more light.
Use this function in the following situations:
● When shooting a moving subject.
● When the distance to the subject changes (so its
size in the LCD monitor or the viewfinder
changes), such as when the subject is backing
away.
● When shooting on a reflective natural background
such as at the beach or when skiing.
● When shooting objects under a spotlight.
● When zooming.
1 Set the Power Switch to “M”.
● The exposure control indicator appears.
3 To brighten the image, press +. To darken the
image, press –. (maximum 6)
● +3 exposure has the same effect as the backlight
● –3 exposure has the same effect as when “r” is
1 Set the Power Switch to “M”.
● The exposure control indicator appears.
3 Adjust zoom so that the subject fills the LCD
monitor or the viewfinder, then press and hold
MENU for over 2 seconds. The exposure control
indicator and the “ ” indication appear.
4 Press MENU. Exposure adjustment is
complete.
To return to automatic exposure control
Switch to “A”.
4 Press MENU. The “ ” indication changes to
“
” and the iris is locked.
NOTES:
To return to automatic iris control
Switch to “A”.
● You cannot use the manual exposure control at
the same time when “r” is set to “SPOTLIGHT”
compensation.
● The exposure control indicator and “
”
disappear.
● If the adjustment does not cause any visible
change in brightness, set “GAIN UP” to “AUTO”.
To lock the exposure control and the iris
exposure control and the iris become automatic.
MasterPage: Start_Right
GR-D240PAL.book Page 31 Wednesday, November 17, 2004 7:32 PM
FEATURES FOR RECORDING
EN
31
Backlight Compensation
Backlight compensation brightens the subject
Spot Exposure Control
Selection of a spot metering area enables more
precise exposure compensation. You can select
one of the three metering areas on the LCD
monitor/viewfinder.
quickly.
With simple operation, backlight compensation
feature brightens the dark subject portion by
increasing the exposure.
1 Set the Power Switch to “M”.
1 Set the Power Switch to “M”.
2 Press BACK LIGHT twice so that the Spot
Exposure Control indicator “ ” appears.
● A spot metering area frame appears at the
centre of the LCD monitor/viewfinder.
2 Press BACK LIGHT so that the Backlight
Compensation indicator “ ” appears.
To cancel Backlight Compensation
Press BACK LIGHT twice so that the “
indicator disappears.
3 Press + or – to select the desired spot
”
metering area frame.
4 Press MENU.
NOTE:
● Spot Exposure Control is engaged.
● Exposure is adjusted to make the brightness of
the selected area most appropriate.
Using Backlight Compensation may cause the light
around the subject to become too bright and the
subject to become white.
To lock the iris
seconds. The “ ” indication appears and the
iris is locked.
To cancel Spot Exposure Control
Press BACK LIGHT once so that the “
”
indicator disappears.
NOTES:
● You cannot use the Spot Exposure Control at the
same time with following functions.
• Manual Exposure Control
● Depending on the shooting location and condition,
optimum result may not be attained.
MasterPage: Left
GR-D240PAL.book Page 32 Wednesday, November 17, 2004 7:32 PM
FEATURES FOR RECORDING
32
EN
White Balance Adjustment
The white balance refers to the correctness of
Manual White Balance Adjustment
Adjust the white balance
colour reproduction under various lighting. If the manually when shooting
white balance is correct, all other colours will be under various types of
accurately reproduced.
lighting.
The white balance is usually adjusted
automatically. However, more advanced
camcorder operators control this function
manually to achieve a more professional colour/
tint reproduction.
1 Set the Power Switch
to “M”.
White paper
2 Select “MWB” in
● The
indication blinks slowly.
To change the setting
3 Hold a sheet of plain white paper in front of
the subject. Adjust zoom or position yourself so
that the white paper fills the screen.
● The selected mode indicator except “AUTO”
appears.
[AUTO]: White balance is adjusted
automatically.
4 Press and hold MENU until
begins
blinking rapidly.
● When the setting is completed,
normal blinking.
resumes
MWB: Adjust the white balance manually
when shooting under various types of lighting.
5 Press MENU twice. The Menu Screen closes
and the Manual White Balance indicator
displayed.
is
FINE: Outdoors on a sunny day.
CLOUD: Outdoors on a cloudy day.
NOTES:
HALOGEN: A video light or similar type of
lighting is used.
[ ] = Factory-preset
paper. In such a case, adjust focus manually.
To return to automatic white balance
Or, set the Power Switch to “A”.
● A subject can be shot under various types of
lighting conditions indoors (natural, fluorescent,
candlelight, etc.). Because the colour temperature
is different depending on the light source, the
subject tint will differ depending on the white
balance settings. Use this function for a more
natural result.
● Once you adjust white balance manually, the
setting is retained even if the power is turned off or
the battery removed.
MasterPage: Start_Right
GR-D240PAL.book Page 33 Wednesday, November 17, 2004 7:32 PM
FEATURES FOR RECORDING
EN
33
WIPE–SCROLL: The scene wipes in from
the bottom to the top of a black screen, or wipes
out from top to bottom, leaving a black screen.
Wipe Or Fader Effects
These effects let you make pro-style scene
transitions. Use them to spice up the transition
from one scene to the next.
Wipe or Fader works when video recording is
started or stopped.
WIPE–SHUTTER: Wipe in from the centre
of a black screen toward the top and bottom, or
wipe out from the top and bottom toward the
centre leaving a black screen.
1 Set the Power Switch to “M”.
● The WIPE/FADER menu disappears and the
effect is reserved.
● The selected effect indicator appears.
3 Press the Recording Start/Stop Button to
activate the Fade-in/out or Wipe-in/out.
To deactivate the selected effect
disappears.
NOTES:
● You can extend the length of a Wipe or Fader by
pressing and holding the Recording Start/Stop
Button.
● Some Wipe/Fader Effects cannot be used with
certain modes of Program AE with special effects.
blinks or goes out.
WIPE/FADER
OFF: Disables the function. (Factory-preset)
FADER–WHITE: Fade in or out with a white
screen.
FADER–BLACK: Fade in or out with a black
screen.
FADER–B.W: Fade in to a colour screen
from a black and white screen, or fade out from
colour to black and white.
WIPE–CORNER: Wipe in on a black screen
from the upper right to the lower left corner, or
wipe out from lower left to upper right, leaving a
black screen.
WIPE–WINDOW: The scene starts in the
centre of a black screen and wipes in toward the
corners, or comes in from the corners, gradually
wiping out to the centre.
WIPE–SLIDE: Wipe in from right to left, or
wipe out from left to right.
WIPE–DOOR: Wipe in as the two halves of
a black screen open to the left and right,
revealing the scene, or wipe out and the black
screen reappears from left and right to cover the
scene.
MasterPage: Left
GR-D240PAL.book Page 34 Wednesday, November 17, 2004 7:32 PM
FEATURES FOR RECORDING
34
EN
SPORTS
Program AE With Special Effects
(Variable Shutter Speed: 1/250 – 1/4000):
This setting allows fast-moving images to be
captured one frame at a time, for vivid, stable
slow-motion playback. The faster the shutter
speed, the darker the picture becomes. Use the
shutter function under good lighting conditions.
1 Set the Power Switch to “M”.
● The PROGRAM AE menu disappears and the
selected effect is activated.
● The selected effect indicator appears.
SNOW: Compensates for subjects that may
otherwise appear too dark when shooting in
extremely bright surroundings such as in the
snow.
To deactivate the selected effect
disappears.
SPOTLIGHT: Compensates for subjects
that may otherwise appear too bright when
shooting under extremely strong direct lighting
such as spotlights.
NOTES:
● Program AE with special effects can be changed
during recording or during Record-Standby.
● Some modes of Program AE with special effects
cannot be used during Night-Scope.
TWILIGHT: Makes evening scenes look
streak may appear (smear phenomenon). Smear
phenomenon tends to occur when “SPORTS” or
any mode of “SHUTTER 1/250 – 1/4000” is
selected.
● Some modes of Program AE with special effects
cannot be used with certain Wipe/Fader effects.
blinks or goes out.
automatically set to “ ”, but can be changed to
your desired setting. When Twilight is chosen,
the camcorder automatically adjusts the focus
from approx. 10 m to infinity. From less than 10
m, adjust the focus manually.
SEPIA: Recorded scenes have a brownish
tint like old photos. Combine this with the
Cinema mode for a classic look.
PROGRAM AE
MONOTONE: Like classic black and white
films, your footage is shot in B/W. Used together
with the Cinema mode, it enhances the “classic
film” effect.
CLASSIC FILM: Gives recorded scenes a
strobe effect.
STROBE: Your recording looks like a series
of consecutive snapshots.
MIRROR: Creates a mirror image on the
right half of the screen, juxtaposed to the normal
image on the other half.
OFF: Disables the function. (Factory-preset)
SHUTTER 1/50: The shutter speed is fixed
at 1/50th of a second. Black bands that usually
appear when shooting a TV screen become
narrower.
SHUTTER 1/120: The shutter speed is
fixed at 1/120th of a second. The flickering that
occurs when shooting under a fluorescent light
or mercury-vapour lamp is reduced.
SHUTTER 1/250/ SHUTTER 1/500/
SHUTTER 1/1000/ SHUTTER 1/2000/
SHUTTER 1/4000: These settings allow fast-
moving images to be captured one frame at a
time, for vivid, stable slow-motion playback by
fixing shutter speed variables. Use these
settings when an automatic adjustment does not
work well, using SPORTS mode. The faster the
shutter speed, the darker the picture becomes.
Use the shutter function under good lighting
conditions.
MasterPage: Start_Right
GR-D240PAL.book Page 35 Wednesday, November 17, 2004 7:32 PM
EDITING
EN
35
1 Following the illustrations, connect the
Dubbing To A VCR
camcorder and the VCR’s input connectors.
3 At the point you want to start dubbing, start
recording on the VCR. (Refer to the VCR’s
instruction manual.)
To S/AV connector
Open the cover.
mark
S/AV cable
(provided)
4 To stop dubbing, stop recording on the VCR,
then stop playback on the camcorder.
NOTES:
● It is recommended to use the AC Adapter as
the power supply instead of the battery pack.
● To choose whether or not the following displays
appear on the connected TV
• Date/time
1
2
3
4
Set “DATE/TIME” to “AUTO”, “ON” or “OFF”.
• Time code
Set “TIME CODE” to “OFF” or “ON”.
Cable
Adapter*
“Y/C”/“CVBS”
Video Out Select
Switch
TV
• Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/
To VCR
VCR
A To S-VIDEO IN**
B Yellow to VIDEO IN
C Red to AUDIO R IN
D White to AUDIO L IN
*
If your VCR has a SCART connector, use the
provided cable adapter. (The provided cable
adapter accepts only output signals from this
camcorder. To use this camcorder as a recorder,
use a commercially available cable adapter.)
** Connect when your TV/VCR has an S-VIDEO IN
connector. In this case, it is not necessary to
connect the yellow video cable.
NOTE:
Set the video out select switch of the cable adapter
as required:
Y/C: When connecting to a TV or VCR which
accepts Y/C signals and uses an S-Video cable.
CVBS: When connecting to a TV or VCR which
does not accept Y/C signals and uses an audio/
video cable.
MasterPage: Left
GR-D240PAL.book Page 36 Wednesday, November 17, 2004 7:32 PM
EDITING
36
EN
1 Make sure all units are turned off.
Dubbing To A Video Unit Equipped
With A DV Connector (Digital
Dubbing)
It is also possible to copy recorded scenes from
the camcorder onto another video unit equipped
with a DV connector. Since a digital signal is
sent, there is little if any image or sound
deterioration.
2 Connect this camcorder to a video unit
equipped with a DV input connector using a DV
cable as shown in the illustration.
4 At the point you want to start dubbing, start
recording on the video unit. (Refer to the video
unit’s instruction manual.)
5 To stop dubbing, stop recording on the video
unit, then stop playback on this camcorder.
NOTES:
● It is recommended to use the AC Adapter as
the power supply instead of the battery pack.
● If a blank portion or disturbed image is played
back on the player during dubbing, the dubbing
may stop so that an unusual image is not dubbed.
● Even though the DV cable is connected correctly,
this occurs, turn off the power and make
connections again.
To DV OUT
● When using a DV cable, be sure to use the
optional JVC VC-VDV204U DV cable.
DV cable (optional)
Core filter
To DV IN
Video unit equipped with DV connector
MasterPage: Start_Right
GR-D240PAL_06Advanced.fm Page 37 Friday, November 19, 2004 4:13 PM
EDITING
EN
37
Connection To A Personal Computer
It is also possible to transfer still/moving images
to a PC with a DV connector by using the
software equipped with the PC or commercially
available software.
®
If you are using a Windows XP, you can use
®
Windows Messenger to conduct video
conferences over the Internet, using a
camcorder. For details, refer to the help for the
Windows Messenger.
To DV OUT
Core filter
®
NOTES:
● It is recommended to use the AC Adapter as
the power supply instead of the battery pack.
● When using a DV cable, be sure to use the
optional JVC VC-VDV206U or VC-VDV204U DV
cable depending on the type of DV connector
(4 or 6 pins) on the PC.
DV cable
(optional)
● The date/time information cannot be captured into
the PC.
Core filter
● Refer to the instruction manuals of the PC and
Software.
● The still images can also be transferred to a PC
with a DV connector-equipped capture board.
● The system may not work properly depending on
the PC or capture board you are using.
To DV connector
When connecting the camcorder to a PC
using a DV cable, make sure to follow the
procedure below. Connecting the cable
incorrectly may cause malfunctions to the
PC with DV connector
camcorder and/or the PC.
● Connect the DV cable first to the PC, and then
to the camcorder.
● Connect the DV cable (plugs) correctly
according to the shape of the DV connector.
MasterPage: Heading0_Left
GR-D240PAL.book Page 38 Wednesday, November 17, 2004 7:32 PM
TROUBLESHOOTING
EN
38
If, after following the steps in the chart below, the
problem still exists, please consult your nearest
JVC dealer.
The LCD monitor or viewfinder indications
blink.
● Certain Wipe/Fader effects, certain modes of
Program AE with special effects, “DIS” and other
functions that cannot be used together are
selected at the same time.
HRe-read the sections covering Wipe/Fader
effects, Program AE with special effects and
The camcorder is a microcomputer-controlled
device. External noise and interference (from a
TV, a radio, etc.) might prevent it from
functioning properly. In such cases, first
disconnect its power supply unit (battery pack,
AC Adapter, etc.) and wait a few minutes; and
then re-connect it and proceed as usual from
the beginning.
Digital Zoom does not work.
● 25X optical zoom is selected.
Power
Video Playback
No power is supplied.
The tape is moving, but there is no picture.
● The power is not connected properly.
● The battery pack is not attached firmly.
HDetach the battery pack once again and re-attach
● The battery is dead.
HReplace the dead battery with a fully charged
● Your TV has AV input terminals, but is not set to
its VIDEO mode.
HSet the TV to the mode or channel appropriate for
● The cassette holder cover is open.
Blocks of noise appear during playback, or
there is no playback picture and the screen
becomes blue.
Video Recording
Recording cannot be performed.
HClean the video heads with an optional cleaning
● The tape’s erase protection tab is set to “SAVE”.
HSet the tape’s erase protection tab to “REC”.
Advanced features
● “TAPE END” appears.
● The cassette holder cover is open.
HClose the cassette holder cover.
The focus does not adjust automatically.
● Focus is set to the Manual mode.
● The lens is dirty or covered with condensation.
HClean the lens and check the focus again.
When shooting a subject illuminated by
bright light, vertical lines appear.
● This is not a malfunction.
In the 5-Second mode, recording ends
before 5 seconds have elapsed.
When the screen is under direct sunlight
during shooting, the screen becomes red or
black for an instant.
● The 5-Second mode is set to “Anim.” in MANUAL
Menu.
HSet “5S” to “5S” in MANUAL Menu.
● This is not a malfunction.
During recording, the date/ time does not
appear.
Snapshot mode cannot be used.
● “DATE/TIME” is set to “OFF”.
● The Squeeze mode (SQUEEZE) is selected.
HDisengage the Squeeze (SQUEEZE) mode.
MasterPage: Start_Right
GR-D240PAL.book Page 39 Wednesday, November 17, 2004 7:32 PM
TROUBLESHOOTING
EN
39
The colour of Snapshot looks strange.
“SET DATE/TIME!” appears.
● The date/time is not set.
● The light source or the subject does not include
white. Or there are various different light sources
behind the subject.
● The built-in clock battery has run out and the
HFind a white subject and compose your shot so
previously set date/time has been erased.
HConsult your nearest JVC dealer for replacement.
The image taken using Snapshot is too
dark.
When the image is printed from the printer,
a black bar appears at the bottom of the
screen.
● Shooting was performed under backlit conditions.
● This is not a malfunction.
this can be avoided.
The image taken using Snapshot is too
bright.
When the camcorder is connected via the
DV connector, the camcorder does not
operate.
● The subject is too bright.
White Balance cannot be activated.
● The DV cable was plugged/unplugged with power
turned on.
HTurn the camcorder’s power off and on again,
● The Sepia (SEPIA) or Monotone (MONOTONE)
mode is activated.
HDisengage the Sepia (SEPIA) or Monotone
(MONOTONE) mode before setting White
then operate it.
Images on the LCD monitor appear dark or
whitish.
The Black & White Fader does not work.
● In places subject to low temperature, images
become dark due to the characteristics of the
LCD monitor. This is not a malfunction.
HAdjust the brightness and angle of the LCD
● The Sepia (SEPIA) or Monotone (MONOTONE)
mode is activated.
HDisengage the Sepia (SEPIA) and Monotone
● When the LCD monitor’s fluorescent light reaches
the end of its service life, images on the LCD
monitor become dark.
The image looks like the shutter speed is
too slow.
HConsult your nearest JVC dealer.
● When shooting in the dark, the unit becomes
highly sensitive to light when “GAIN UP” is set to
“AUTO”.
Coloured bright spots appear all over the
LCD monitor or the viewfinder.
HIf you want the lighting to look more natural, set
● The LCD monitor and the viewfinder are made
with high-precision technology. However, black
spots or bright spots of light (red, green or blue)
may appear constantly on the LCD monitor or the
viewfinder. These spots are not recorded on the
tape. This is not due to any defect of the unit.
(Effective dots: more than 99.99 %)
Other problems
The POWER/CHARGE lamp on the
camcorder does not light during charging.
● Charging is difficult in places subject to extremely
high/low temperatures.
The cassette will not load properly.
HTo protect the battery, it is recommended to
charge it in places with a temperature of 10°C to
● The battery’s charge is low.
● The battery pack is not attached firmly.
HDetach the battery pack once again and re-attach
MasterPage: Left
GR-D240PAL.book Page 40 Wednesday, November 17, 2004 7:32 PM
TROUBLESHOOTING
40
EN
Warning Indications
Picture does not appear on the LCD
monitor.
● The viewfinder is pulled out and “PRIORITY” is
set to “FINDER”.
HPush the viewfinder back in or set “PRIORITY” to
Displays the battery remaining power.
Remaining power level
● The LCD monitor’s brightness setting is too dark.
HAdjust the brightness of the LCD monitor.
HIf the monitor is tilted upward 180 degrees, open
High
Exhausted
As the battery power comes close to nil, the
battery remaining power indicator blinks.
When the battery power is exhausted, power
turns off automatically.
An error indication (01 – 04 or 06) appears.
● A malfunction of some kind has occurred. In this
case the camcorder’s functions become
unusable.
CHECK TAPE’S ERASE PROTECTION TAB
Appears when the erase protection tab is set to
“SAVE” while the Power Switch is set to “A” or
USE CLEANING CASSETTE
Appears if dirt is detected on the heads during
recording. Use an optional cleaning cassette.
CONDENSATION, OPERATION
PAUSED PLEASE WAIT
Appears if condensation occurs. When this
indication is displayed, wait more than 1 hour
until condensation disappears.
TAPE!
Appears if a tape is not loaded when the
Recording Start/Stop Button or SNAPSHOT
Button is pressed while the Power Switch is set
to “A” or “M”.
TAPE END
Appears when the tape ends during recording or
playback.
SET DATE/TIME!
● Appears when the date/time is not set.
● The built-in clock battery has run out and the
previously set date/time has been erased.
Consult your nearest JVC dealer for
replacement.
MasterPage: Start_Right
GR-D240PAL.book Page 41 Wednesday, November 17, 2004 7:32 PM
TROUBLESHOOTING
EN
41
LENS CAP
Appears for 5 seconds after power is turned on if
the lens cap is attached or when it is dark.
HDV
Appears when pictures recorded in the HDV
format are detected. The pictures in the HDV
format cannot be played back with this
camcorder.
UNIT IN SAFEGUARD MODE
REMOVE AND REATTACH BATTERY
The error indications (01, 02 or 06) show what
type of malfunction has occurred. When an error
indication appears, the camcorder turns off
automatically. Remove the power supply
(battery, etc.) and wait a few minutes for the
indication to clear. When it does, you can
resume using the camcorder. If the indication
remains, consult your nearest JVC dealer.
UNIT IN SAFEGUARD MODE
EJECT AND REINSERT TAPE
The error indications (03 or 04) show what type
of malfunction has occurred. When an error
indication appears, the camcorder turns off
automatically. Eject the cassette once and re-
insert it, then check if the indication clears.
When it does, you can resume using the
camcorder. If the indication remains, consult
your nearest JVC dealer.
MasterPage: Heading0_Left
GR-D240PAL.book Page 42 Wednesday, November 17, 2004 7:32 PM
USER MAINTENANCE
42
EN
Cleaning The Camcorder
Before cleaning, turn off the camcorder and
remove the battery pack and AC Adapter.
To clean the exterior
Wipe gently with a soft cloth. Put the cloth in
diluted mild soap and wring it well to wipe off
heavy dirt. Then wipe again with a dry cloth.
To clean the LCD monitor
Wipe gently with a soft cloth. Be careful not to
damage the monitor. Close the LCD monitor.
To clean the lens
Blow it with a blower brush, then wipe gently
with lens cleaning paper.
NOTES:
● Avoid using strong cleaning agents such as
benzine or alcohol.
● Cleaning should be done only after the battery
pack has been removed or other power units have
been disconnected.
● Mould may form if the lens is left dirty.
● When using a cleaner or chemically treated cloth
refer to the cautions of each product.
● To clean the viewfinder, please consult your
nearest JVC dealer.
MasterPage: Start_Right
GR-D240PAL.book Page 43 Wednesday, November 17, 2004 7:32 PM
CAUTIONS
EN
43
Battery Packs
NOTES:
● It is normal for the battery pack to be warm after
charging, or after use.
The supplied battery
pack is a lithium-ion
battery. Before using the
supplied battery pack or
an optional battery pack,
be sure to read the
following cautions:
Terminals
Temperature Range Specifications
Charging: 10°C to 35°C
Operation: 0°C to 40°C
Storage: –20°C to 50°C
● The lower the temperature, the longer recharging
takes.
● Charging times are for a fully discharged battery
● To avoid hazards
...do not burn.
pack.
...do not short-circuit the terminals. When
transporting, make sure the provided battery cap
is attached to the battery. If the battery cap is
misplaced, carry the battery in a plastic bag.
...do not modify or disassemble.
...do not expose the battery to temperatures
exceeding 60°C, as this may cause the battery to
overheat, explode or catch fire.
...use only specified chargers.
● To prevent damage and prolong service
life
...do not subject to unnecessary shock.
...charge in an environment where temperatures
are within the tolerances shown in the chart
below. This is a chemical reaction type battery —
cooler temperatures impede chemical reaction,
while warmer temperatures can prevent
complete charging.
...store in a cool, dry place. Extended exposure to
high temperatures will increase natural discharge
and shorten service life.
...fully charge and then fully discharge the battery
every 6 months when storing the battery pack
over a long period time.
...remove from charger or powered unit when not in
use, as some machines use current even when
switched off.
Cassettes
To properly use and store your cassettes, be
sure to read the following cautions:
● During use
...make sure the cassette bears the Mini DV mark.
...be aware that recording onto prerecorded tapes
automatically erases the previously recorded
video and audio signals.
...make sure the cassette is positioned properly
when inserting.
...do not load and unload the cassette repeatedly
without allowing the tape to run at all. This
slackens the tape and can result in damage.
...do not open the front tape cover. This exposes
the tape to fingerprints and dust.
● Store cassettes
...away from heaters or other heat sources.
...out of direct sunlight.
...where they won’t be subject to unnecessary
shock or vibration.
...where they won’t be exposed to strong magnetic
fields (such as those generated by motors,
transformers or magnets).
...vertically, in their original cases.
The Benefits Of Lithium-Ion Batteries
Lithium-ion battery packs are small but have a
large power capacity. However, when one is
exposed to cold temperatures (below 10°C),
its usage time becomes shorter and it may
cease to function. If this happens, place the
battery pack in your pocket or other warm,
protected place for a short time, then re-
attach it to the camcorder.
MasterPage: Left
GR-D240PAL.book Page 44 Wednesday, November 17, 2004 7:32 PM
CAUTIONS
44
EN
● To protect the unit, DO NOT
LCD Monitor
● To prevent damage to the LCD monitor, DO
NOT
...push it strongly or apply any shocks.
...place the camcorder with the LCD monitor on the
bottom.
...allow it to become wet.
...drop the unit or strike it against hard objects.
...subject it to shock or excessive vibration during
transportation.
...keep the lens directed at extremely bright objects
for long periods.
● To prolong service life
...expose the lens and viewfinder’s lens to direct
sunlight.
...carry it by holding the LCD monitor or the
viewfinder.
...swing it excessively when using the hand strap or
the grip.
...swing the soft camera case excessively when the
camcorder is inside it.
● Dirty heads can cause the following
problems:
...avoid rubbing it with coarse cloth.
● Be aware of the following phenomena for
LCD monitor use. These are not
malfunctions
...While using the camcorder, the surface around
the LCD monitor and/or the back of the LCD
monitor may heat up.
...If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
Main Unit
● For safety, DO NOT
...open the camcorder’s chassis.
...disassemble or modify the unit.
...short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use.
...allow inflammables, water or metallic objects to
enter the unit.
...remove the battery pack or disconnect the power
supply while the power is on.
...leave the battery pack attached when the
camcorder is not in use.
...No picture during playback.
...Blocks of noise appear during playback.
...During recording or playback, the Head Clog
Warning indicator “ ” appears.
...Recording cannot be performed properly.
In such cases, use an optional cleaning
cassette. Insert it and play back. If the cassette
is used more than once consecutively, damage
to the video heads may result. After the
camcorder plays back for about 20 seconds, it
stops automatically. Also refer to the cleaning
cassette’s instructions.
● Avoid using the unit
...in places subject to excessive humidity or dust.
...in places subject to soot or steam such as near a
cooking stove.
If, after using the cleaning cassette, the
problems still exist, consult your nearest JVC
dealer.
...in places subject to excessive shock or vibration.
...near a television set.
Mechanical moving parts used to move the
video heads and video tape tend to become
dirty and worn out over time. In order to maintain
a clear picture at all times, periodic check-ups
are recommended after using the unit for about
1,000 hours. For periodic check-ups please
consult your nearest JVC dealer.
...near appliances generating strong magnetic or
electric fields (speakers, broadcasting antennas,
etc.).
...in places subject to extremely high (over 40°C) or
extremely low (under 0°C) temperatures.
● DO NOT leave the unit
...in places of over 50°C.
...in places where humidity is extremely low (below
35%) or extremely high (above 80%).
...in direct sunlight.
...in a closed car in summer.
...near a heater.
MasterPage: Start_Right
GR-D240PAL.book Page 45 Wednesday, November 17, 2004 7:32 PM
CAUTIONS
EN
45
About moisture condensation
● You have observed that pouring a cold liquid
into a glass will cause drops of water to form on
the glass’ outer surface. This same
phenomenon occurs on the head drum of a
camcorder when it is moved from a cool place
to a warm place, after heating a cold room,
under extremely humid conditions or in a place
directly subjected to the cool air from an air
conditioner.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC
dealer.
The camcorder is a microcomputer-controlled
device. External noise and interference (from
a TV, a radio, etc.) might prevent it from
functioning properly. In such cases, first
disconnect its power supply unit (battery pack,
AC Adapter, etc.) and wait a few minutes and
then re-connect it and proceed as usual from
the beginning.
MasterPage: Heading0_Left
GR-D240PAL.book Page 46 Wednesday, November 17, 2004 7:32 PM
SPECIFICATIONS
46
EN
Camcorder
For Digital Video Camera
Format
DV format (SD mode)
Signal format
PAL standard
Recording/Playback format
For General
Power supply
DC 11 V (Using AC Adapter)
DC 7.2 V (Using battery pack)
Power consumption
Approx. 3.2 W (LCD monitor off, viewfinder on)
Approx. 4.2 W (LCD monitor on, viewfinder off)
Dimensions (W x H x D)
56 mm x 94 mm x 112 mm (with the LCD monitor
closed and the viewfinder pushed back in)
Weight
Approx. 430 g (without battery, cassette and lens
cap)
Approx. 510 g (incl. battery, cassette and lens cap)
Video: Digital component recording
Audio: PCM digital recording, 32 kHz 4-channel
(12-BIT), 48 kHz 2-channel (16-BIT)
Cassette
Mini DV cassette
Tape speed
SP: 18.8 mm/s, LP: 12.5 mm/s
Maximum recording time (using 80 min.
cassette)
SP: 80 min., LP: 120 min.
Operating temperature
0°C to 40°C
Operating humidity
35% to 80%
Storage temperature
For Connectors
S/AV
S-Video output:
Y: 1.0 V (p-p), 75 Ω, analogue
C: 0.29 V (p-p), 75 Ω, analogue
Video output: 1.0 V (p-p), 75 Ω, analogue
Audio output: 300 mV (rms), 1 kΩ, analogue, stereo
Microphone input
ø3.5 mm, stereo
DV
–20°C to 50°C
Pickup
1/6" CCD
Lens
F 1.8, f = 2.2 mm to 55 mm, 25:1 power zoom lens
Filter diameter
ø27 mm
LCD monitor
Output: 4-pin, IEEE 1394 compliant
2.5" diagonally measured, LCD panel/TFT active
matrix system
Viewfinder
Electronic viewfinder with 0.16" colour LCD
Speaker
Monaural
AC Adapter
Power requirement
AC 110 V to 240 Vd, 50 Hz/60 Hz
Output
DC 11 V G, 1 A
Specifications shown are for SP mode unless
otherwise indicated. E & O.E. Design and
specifications subject to change without notice.
MasterPage: Start_Right
GR-D240PAL.book Page 47 Wednesday, November 17, 2004 7:32 PM
EN
47
A
S
AC Adapter .................................................... 13 Snapshot Mode .............................................. 23
Animation ....................................................... 24 Sound Mode ............................................ 23, 26
B
T
Blank Search ................................................. 20 Tape Speed (REC MODE) ...................... 23, 26
C
W
D
Z
Dubbing ................................................... 35, 36 Zooming ................................................... 18, 23
E
Exposure Control ........................................... 30 5-Second Recording ...................................... 28
I
L
M
N
P
Q
R
Recording Capacity
MasterPage: BackCover
GR-D240PAL.book Page 48 Wednesday, November 17, 2004 7:32 PM
EN
Printed in Malaysia
1104MKH-ID-VM
EK/EX
© 2004 Victor Company of Japan, Limited
|