JVC GR AXM917UM User Manual

COMPACT VHS CAMCORDER  
ENGLISH  
GR-AXM917UM  
INSTRUCTIONS  
LYT0299-001A  
EN  
EN3  
IMPORTANT PRODUCT  
SAFETY INSTRUCTIONS  
ANTENNA INSTALLATION  
INSTRUCTIONS  
1. Outdoor Antenna Grounding  
Electrical energy can perform many useful functions.  
But improper use can result in potential electrical  
shock or fire hazards. This product has been  
engineered and manufactured to assure your  
personal safety. In order not to defeat the built-in  
safeguards, observe the following basic rules for its  
installation, use and servicing.  
If an outside antenna or cable system is connected to  
the product, be sure the antenna or cable system is  
grounded so as to provide some protection against  
voltage surges and built-up static charges. Article 810  
of the National Electrical Code, ANSI/NFPA 70,  
provides information with regard to proper grounding  
of the mast and supporting structure, grounding of  
the lead-in wire to an antenna discharge unit, size of  
grounding conductors, location of antenna discharge  
unit, connection to grounding electrodes, and  
requirements for the grounding electrode.  
ATTENTION:  
Follow and obey all warnings and instructions  
marked on your product and its operating  
instructions. For your safety, please read all the safety  
and operating instructions before you operate this  
product and keep this manual for future reference.  
2. Lightning  
For added protection for this product during a  
lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the  
wall outlet and disconnect the antenna or cable  
system. This will prevent damage to the product due  
to lightning and power-line surges.  
INSTALLATION  
1. Power Sources  
Operate your product only from the type of power  
source indicated on the marking label. If you are not  
sure of the type of power supply to your home,  
consult your product dealer or local power company.  
If your product is intended to operate from battery  
power, or other sources, refer to the operating  
instructions.  
3. Power Lines  
An outside antenna system should not be located in  
the vicinity of overhead power lines or other electric  
light or power circuits, or where it can fall into such  
power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to  
keep from touching such power lines or circuits as  
contact with them might be fatal.  
2. Overloading  
Do not overload wall outlets, extension cords, or  
integral convenience receptacles as this can result in  
a risk of fire or electric shock.  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70  
3. Power Cord Protection  
Power supply cords should be routed so that they are  
not likely to be walked on or pinched by items  
placed upon or against them, paying particular  
attention to cords at plugs, convenience receptacles,  
and the point where they exit from the product.  
ANTENNA  
LEAD IN WIRE  
GROUND CLAMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION  
4. Ventilation  
810-20)  
ELECTRIC SERVICE  
EQUIPMENT  
Slots and openings in the cabinet are provided for  
ventilation. To ensure reliable operation of the  
product and to protect it from overheating, these  
openings must not be blocked or covered.  
Do not block the openings by placing the product  
on a bed, sofa, rug or other similar surface.  
Do not place the product in a built-in installation  
such as a bookcase or rack unless proper  
ventilation is provided or the manufacturer’s  
instructions have been adhered to.  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
POWER SERVICE GROUNDING ELECTRODE SYSTEM  
(NEC ART 250. PART H)  
NEC – NATIONAL ELECTRICAL CODE  
5. Wall or Ceiling Mounting  
The product should be mounted to a wall or ceiling  
only as recommended by the manufacturer.  
4
EN  
USE  
SERVICING  
1. Servicing  
1. Accessories  
To avoid personal injury:  
If your product is not operating correctly or exhibits a  
marked change in performance and you are unable  
to restore normal operation by following the detailed  
procedure in its operating instructions, do not  
attempt to service it yourself as opening or removing  
covers may expose you to dangerous voltage or other  
hazards. Refer all servicing to qualified service  
personnel.  
Do not place this product on an unstable cart,  
stand, tripod, bracket or table. It may fall, causing  
serious injury to a child or adult, and serious  
damage to the product.  
Use only with a cart, stand, tripod, bracket, or table  
recommended by the manufacturer or sold with the  
product.  
Use a mounting accessory recommended by the  
manufacturer and follow the manufacturer’s  
instructions for any mounting of the product.  
Do not try to roll a cart with small casters across  
thresholds or deep-pile carpets.  
2. Damage Requiring Service  
Unplug this product from the wall outlet and refer  
servicing to qualified service personnel under the  
following conditions:  
a. When the power supply cord or plug is damaged.  
b. If liquid has been spilled, or objects have fallen  
into the product.  
2. Product and Cart  
Combination  
A product and cart  
PORTABLE CART WARNING  
(Symbol provided by RETAC)  
c. If the product has been exposed to rain or water.  
d. If the product does not operate normally by  
following the operating instructions. Adjust only  
those controls that are covered by the operating  
instructions as an improper adjustment of other  
controls may result in damage and will often  
require extensive work by a qualified technician  
to restore the product to its normal operation.  
e. If the product has been dropped or damaged in  
any way.  
combination should be  
moved with care. Quick  
stops, excessive force, and  
uneven surfaces may cause  
the product and cart  
combination to overturn.  
3. Water and Moisture  
Do not use this product near water—for example,  
near a bath tub, wash bowl, kitchen sink or laundry  
tub, in a wet basement, or near a swimming pool and  
the like.  
f. When the product exhibits a distinct change in  
performance—this indicates a need for service.  
3. Replacement Parts  
4. Object and Liquid Entry  
When replacement parts are required, be sure the  
service technician has used replacement parts  
specified by the manufacturer or have the same  
characteristics as the original part. Unauthorized  
substitutions may result in fire, electric shock or other  
hazards.  
Never push objects of any kind into this product  
through openings as they may touch dangerous  
voltage points or short-out parts that could result in a  
fire or electric shock. Never spill liquid of any kind  
on the product.  
5. Attachments  
4. Safety Check  
Do not use attachments not recommended by the  
manufacturer of this product as they may cause  
hazards.  
Upon completion of any service or repairs to this  
product, ask the service technician to perform safety  
checks to determine that the product is in safe  
operating condition.  
6. Cleaning  
Unplug this product from the wall outlet before  
cleaning. Do not use liquid cleaners or aerosol  
cleaners. Use a damp cloth for cleaning.  
7. Heat  
The product should be situated away from heat  
sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce  
heat.  
MAJOR FEATURES  
EN5  
REMEMBER  
Digital Still Camera Built-in  
(PC communication capable)  
(pg. 22 – 25, 52 – 59)  
The Logical Choice  
Menu Adjustment  
(pg. 36, 37, 38)  
The only compact video  
cassettes that can be  
used with your VHS VCR*  
Integrated Auto Light  
(pg. 30)  
Program AE with Special  
Effects (pg. 32, 33)  
Picture Stabilizer (pg. 29)  
Electronic Fog Filter  
ND Effect  
Sepia  
Twilight  
Sports  
Nega/Posi  
1/2000 sec. High Speed Shutter  
Digital Hyper Zoom  
(pg. 28)  
Zoom in  
LCD Color Monitor  
(pg. 20)  
Zoom out  
Cassettes marked  
camcorder.  
can be used with this  
QUICK OPERATION GUIDE (VIDEO)  
6
EN  
The image you shoot is recorded onto a video tape.  
SUPPLY POWER  
INSERTING A VIDEO  
CASSETTE  
A
Hook on.  
B Push in.  
PUSH Button  
EJECT Switch  
BATTERY RELEASE  
Using the battery pack  
1 Open the LCD monitor to an angle of over 60  
degrees.  
Hook its end to the camcorder ( ) and push the  
battery pack in until it locks in place ( ).  
(Charging procedure, pg. 10)  
2 Slide EJECT to open the cassette holder.  
3 Insert a video cassette.  
To remove the battery pack  
Slide BATTERY RELEASE and pull out the battery  
pack.  
4 Press PUSH to close the cassette holder.  
(For more details, pg. 15)  
SHOOTING  
PLAYBACK  
REW (2) Button  
3
1
LENS COVER  
Open/Close Ring  
3
Set to “AUTO”  
or “PRO.”  
4 P( LAY/PAUSE  
4/6) Button  
Set to “PLAY”  
2
Recording Start/Stop Button  
4
STOP (5) Button  
Set to “VIDEO”  
1
Set to “VIDEO”  
2
1 Set the System Select Switch to “VIDEO”.  
2 Set the Power Switch to “PLAY”.  
3 Press REW (2).  
1 Turn the LENS COVER Open/Close Ring to  
open the lens cover.  
2 Set the System Select Switch to “VIDEO”.  
3 Set the Power Switch to “AUTO” or “PRO.”.  
— The power lamp will light and an image  
will appear.  
— The tape will automatically stop at the  
beginning of the tape.  
4 Press PLAY/PAUSE (4/6).  
— Playback starts and the playback picture  
appears.  
To stop playback, press STOP (5).  
(For more details, pg. 46.)  
The viewfinder switches off automatically to  
save power when the LCD monitor is opened  
at an angle of over 60 degrees.  
The LCD monitor turns on/off when it is  
opened/closed at approx. 60 degrees.  
4 Press the Recording Start/Stop Button.  
— Recording starts.  
To stop recording temporarily, momentarily  
press the Recording Start/Stop Button once  
again.  
(For more details, pgs. 18 – 21)  
The viewfinder switches off automatically to  
save power when the LCD monitor is opened  
at an angle of over 60 degrees.  
The LCD monitor turns on/off when it is  
opened/closed at approx. 60 degrees.  
Or simply play back the tape on a VHS VCR  
using the Cassette Adapter (VHS Playpak).  
pg. 49  
QUICK OPERATION GUIDE (D.S.C.)  
A still image you shoot is stored in the camcorder's built-in memory.  
EN7  
SHOOTING  
SUPPLY POWER  
A
Hook on.  
B Push in.  
SNAPSHOT Button  
4
LENS COVER  
Open/Close Ring  
1
Set to “AUTO”  
or “PRO.”  
3
System Select Switch  
Set to “D.S.C.”  
BATTERY RELEASE  
2
Using the battery pack  
Hook its end to the camcorder ( ) and push the  
battery pack in until it locks in place ( ).  
(Charging procedure, pg. 10)  
To remove the battery pack  
Slide BATTERY RELEASE and pull out the battery  
pack.  
1 Turn the LENS COVER Open/Close Ring to  
open the lens cover.  
2 Set the System Select Switch to “D.S.C.”.  
3 Set the Power Switch to “AUTO” or “PRO.”.  
— The power lamp will light and an image  
will appear.  
4 Press the SNAPSHOT Button.  
— A still image is shot and is stored in the  
camcorder’s memory.  
PLAYBACK  
(For more details, pgs. 22 – 25)  
REW (2/PAGE –) Button,  
The viewfinder switches off automatically to  
save power when the LCD monitor is opened  
at an angle of over 60 degrees.  
The LCD monitor turns on/off when it is  
opened/closed at approx. 60 degrees.  
FF (3/PAGE +) Button  
3
2
Set to “PLAY”  
1
System Select Switch  
Set to “D.S.C.”  
1 Set the System Select Switch to “D.S.C.”.  
2 Set the Power Switch to “PLAY”.  
— A still image stored in memory appears.  
3 Press REW (2/PAGE –) or FF (3/PAGE +) to  
select the still image you want to view.  
(For more details, pg. 52.)  
The viewfinder switches off automatically to  
save power when the LCD monitor is opened  
at an angle of over 60 degrees.  
The LCD monitor turns on/off when it is  
opened/closed at approx. 60 degrees.  
CONTENTS  
8
EN  
GETTING STARTED  
10 – 17  
Power.......................................................................................................... 10  
Clock (Lithium) Battery Insertion/Removal .............................................................. 12  
Date/Time Settings.......................................................................................... 13  
Recording Mode Setting..................................................................................... 14  
Tape Length Setting .......................................................................................... 14  
Loading/Unloading A Cassette............................................................................. 15  
Grip Adjustment .............................................................................................. 16  
Viewfinder Adjustment ..................................................................................... 16  
Shoulder Strap Attachment ................................................................................. 17  
Tripod Mounting .............................................................................................. 17  
VIDEO RECORDING  
18 – 21  
Basic Recording............................................................................................... 18  
DIGITAL STILL CAMERA (D.S.C.) SHOOTING  
22 – 25  
Basic Shooting ................................................................................................ 22  
RECORDING  
26 – 45  
Basic Features ................................................................................................ 26  
Advanced Features........................................................................................... 31  
VIDEO PLAYBACK  
46 – 49  
Basic Playback................................................................................................ 46  
Features ....................................................................................................... 47  
Using The Cassette Adapter ................................................................................ 49  
PLAYBACK  
50 – 51  
Basic Connections And Tape Dubbing ...................................................................... 50  
D.S.C. PLAYBACK  
52 – 59  
Basic Playback................................................................................................ 52  
Connection .................................................................................................... 53  
Advanced Features........................................................................................... 54  
USING THE REMOTE CONTROL UNIT  
60 – 64  
Insert Editing (VIDEO)....................................................................................... 62  
Insert Editing (Insert A Still Image From The Built-in Memory Onto A Tape) ....................... 63  
Audo Dubbing................................................................................................. 64  
EN9  
USER MAINTENANCE  
TROUBLESHOOTING  
INDEX  
65  
66 – 68  
69 – 73  
Controls, Connectors And Indicators ...................................................................... 69  
Indications..................................................................................................... 71  
Terms .......................................................................................................... 72  
CAUTIONS  
74 – 76  
77  
SPECIFICATIONS  
OPTIONAL ACCESSORIES  
77  
PROVIDED ACCESSORIES  
AC Power Adapter/  
Charger AA-V15U  
Cassette Adapter  
(VHS Playpak) C-P7U  
Battery Pack  
BN-V20U  
Shoulder Strap  
DC Cord  
Remote Control  
Unit RM-V705U  
(for Windows® PC)  
Lithium Battery CR2025 x 2  
(for clock operation and  
remote control unit)  
CD-ROM including two  
software programs  
•PC Connection Cable x 1  
GETTING STARTED  
10  
EN  
Marks  
Power  
This camcorder’s 3-way power supply system lets you choose  
the most appropriate source of power.  
To AC outlet  
CHARGE indicator  
NOTES:  
No function is available without power supply.  
Use only the specified power supply.  
Do not use provided power supply units with other  
equipment.  
CHARGING THE BATTERY PACK  
REFRESH switch  
SUPPLY POWER  
1 Connect the charger’s AC power cord to a wall outlet.  
REFRESH indicator  
ATTACH BATTERY PACK  
2 Align the marks and slide the battery pack in the  
REFRESH  
direction of the arrow until it locks in place.  
The AC Power Adapter/Charger features a  
REFRESH function that allows you to fully  
discharge the battery pack before recharg-  
ing.  
Perform the REFRESH function after no less  
than 5 chargings.  
The CHARGE indicator begins blinking to indicate  
charging has started.  
DETACH BATTERY PACK  
3 When the CHARGE indicator stops blinking but stays lit,  
charging is finished. Slide the battery pack opposite the  
direction of the arrow.  
To discharge the battery . . .  
.... attach the battery pack to the adapter as  
shown in the above illustration. Then  
push REFRESH. The REFRESH indicator  
lights when discharging starts, and goes  
out when discharging is complete.  
Battery pack  
BN-V12U  
BN-V20U  
Charging time  
approx. 1 hr. 10 min.  
approx. 1 hr. 50 min  
Discharging time  
approx. 3 hrs. 30 min.  
approx. 6 hrs. 40 min.  
USING THE BATTERY PACK  
A
ATTACH BATTERY PACK  
Hook on.  
1 Hook its end to the camcorder (  
) and push the battery  
B
Push in.  
pack in until it locks in place (  
) .  
DETACH BATTERY PACK  
2 Slide BATTERY RELEASE and pull out the battery pack.  
Approximate recording time (unit: min.)  
LCD  
LCD  
LCD  
Battery pack monitor on/  
monitor off/  
monitor on/  
Viewfinder off Viewfinder on Viewfinder on  
BN-V12U  
BN-V20U  
45 (30)  
80 (50)  
50 (35)  
85 (55)  
40 (30)  
70 (45)  
BATTERY RELEASE  
(
) : when the video light is on.  
INFORMATION:  
VU-V856KIT is a set composed of the BN-V856U battery pack  
and AA-V80U AC Power Adapter/Charger.  
ATTENTION:  
Before detaching the power source,  
make sure that the camcorders power  
is turned off. Failure to do so can result  
in a camcorder malfunction.  
The BN-V856U battery pack provides approx. 7 hours of  
recording time when the viewfinder is on and the LCD  
monitor and the video light are off. Also read thoroughly the  
VU-V856KIT’s instruction manuals.  
It is impossible to charge the BN-V856U battery pack using  
the provided AC Power Adapter/Charger. Use the optional  
AA-V80U AC Power Adapter/Charger.  
EN11  
Charge Marker  
A charge marker is provided on the battery pack to  
help you remember whether it has been charged or  
not. Two colors are provided (red and black)—you  
choose which one means charged and which means  
discharged.  
Charge marker  
NOTES:  
The recording time per charge is affected by such factors as the time spent in Record-Standby mode and the  
frequency of zooming. It is safer to have spare battery packs to cover 3 times the planned shooting time.  
Charging times noted on page 10 are for a fully discharged battery pack, and discharging times are for a fully  
charged battery pack.  
Charging and discharging times vary according to the ambient temperature and the status of the battery pack.  
Remember to set the charge marker after charging a battery pack or after detaching a discharged one from  
your camcorder.  
Perform the REFRESH function after no less than 5 chargings.  
While the AC Power Adapter/Charger’s power cord is disconnected from the AC outlet, it is possible to  
discharge the battery by pressing the REFRESH switch. During that time, the AC Power Adapter/Charger does  
not charge the battery. When discharging is complete, detach the battery from the AC Power Adapter/  
Charger to store it.  
High temperatures can damage the battery pack, so use only where good ventilation is available. Do not  
allow it to discharge in a container, such as a bag.  
If you stop recharging or discharging part way through, make sure to remove the battery pack before  
unplugging the adapter’s AC cord.  
Remove the battery pack from the adapter immediately after discharging.  
To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.  
Make sure you unplug the DC cord before charging or discharging the battery pack.  
The CHARGE indicator may not light properly with a brand new battery pack, or with one that has been  
stored for an extended period. In this case, remove and reattach the battery pack and recharge it. The  
CHARGE indicator should blink during recharging. If it doesn’t, contact your nearest JVC dealer.  
USING AC POWER  
To DC IN jack  
To AC outlet  
Use the AC Power Adapter/Charger (connect as  
shown in the illustration to the left).  
DC OUT  
terminal  
NOTES:  
The provided AC Power Adapter/Charger features  
automatic voltage selection in the AC range from  
110 V to 240 V.  
AC Power  
Adapter/Charger  
AA-V15U  
When using the DC cord, make sure you connect  
the end of the cord with the core filter to the  
camcorder. The core filter reduces interference.  
DC Cord  
USING A CAR BATTERY  
Use the optional Car Battery Cord or Car Battery  
Charger/Adapter (connect as shown in the  
illustration to the left).  
To car’s  
cigarette  
lighter  
socket  
Car Battery Cord  
AP-V7U (optional)  
NOTES:  
When using the car battery, leave the engine  
idling.  
The optional Car Battery Charger/Adapter  
(BH-V3U) can also be used to charge the battery  
pack (except BN-V20U/V856U).  
When using the optional Car Battery Charger/  
Adapter or Car Battery Cord (AP-V7U), refer to the  
respective instruction booklet.  
Car Battery  
Charger/Adapter  
BH-V3U (optional)  
GETTING STARTED (cont.)  
12  
EN  
Slot  
Clock (Lithium) Battery Insertion/Removal  
This battery is necessary for clock operation and to  
perform date/time settings.  
SWITCH OFF POWER  
1 Switch off the unit’s power and remove the power  
supply unit (battery pack, AC Power Adapter/Battery  
Charger, etc.).  
REMOVE BATTERY HOLDER  
2 Pull out the battery holder.  
Battery holder  
INSERT BATTERY IN HOLDER  
3 Insert the battery in the holder, and be sure to have  
the “+” mark visible.  
RE-INSERT HOLDER  
4 Slide the holder back into the slot until you hear a  
click.  
NOTE:  
See “SAFETY PRECAUTIONS” (pg. 2) for information  
on safe handling of lithium batteries.  
EN13  
Date/Time Settings  
SELECT OPERATION SYSTEM AND  
1 MODE  
System  
Select Switch  
Set the System Select Switch to “VIDEO” or “D.S.C.” ,  
and set the Power Switch to “PRO.”.  
The power lamp comes on.  
ACCESS MENU SCREEN  
2 Press MENU.  
SELECT FUNCTION  
MENU Button  
3 Rotate the Select Dial to move the highlight bar to  
“DATE/TIME”, then press it. The DATE/TIME Menu  
appears.  
Power lamp  
If you decide you want to return the date and time  
to the previous settings, rotate the Select Dial to  
move the highlight bar to “EXIT” and press it, then  
go to step 7.  
If you want to set only the time without changing  
the date, go to step 5.  
Select Dial  
Power Switch  
SET DATE  
4 Rotate the Select Dial to move the highlight bar to the  
Display  
item you want to set and then press it. When the  
setting begins blinking, rotate the Select Dial until the  
correct setting appears and then press it. The setting  
stops blinking.  
Menu Screen  
4
NEXT  
M.W.B.  
AUTO  
ON  
D . ZOOM  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T30  
PICTURE  
FINE  
FULL  
Repeat this procedure until you’re satisfied with the  
Date settings (“YEAR”, “MONTH” and “DAY”).  
SNAPSHOT  
4RETURN  
SET TIME  
5 Rotate the Select Dial to move the highlight bar to  
DATE TIME  
DATE/TIME Menu  
“TIME” and then press it. When the hour setting  
begins blinking, rotate the Select Dial until the correct  
setting appears and then press it. When the hour  
setting stops blinking and the minute setting begins  
blinking, rotate the Select Dial until the correct setting  
appears and then press it. The minute setting stops  
blinking.  
YEAR  
1999  
JAN  
MONTH  
DAY  
1
TIME  
PM 12 : 00  
12-hour indication  
with AM or PM  
EXIT  
START CLOCK OPERATION  
4
NEXT  
6 When none of these settings (“YEAR”, “MONTH”,  
M.W.B.  
AUTO  
ON  
D . ZOOM  
“DAY”, “TIME”) blinks, rotate the Select Dial to move  
the highlight bar to “EXIT”, and press it. The Menu  
Screen reappears with the highlight bar on  
“RETURN”.  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T30  
PICTURE  
FINE  
FULL  
SNAPSHOT  
4RETURN  
CLOSE MENU SCREEN  
7 Press the Select Dial.  
NOTE:  
To display the date and time in the camcorder’s display  
and on a connected TV, see “Date/Time Insert”  
(pg. 34).  
GETTING STARTED (cont.)  
14  
EN  
Recording Mode Setting  
Set depending on your preference.  
SET RECORDING MODE  
System  
Select Switch  
1 First set the System Select Switch to “VIDEO”, then  
set the Power Switch to “AUTO” or “PRO.”. Press SP/  
EP for more than 1 second. “SP” (Standard Play)  
provides higher picture and sound quality and is  
better for dubbing, while “EP” (Extended Play) is  
more economical, providing three times the record-  
ing time.  
MENU Button  
SP/EP Recording  
NOTE:  
If the recording mode is switched during recording, the  
playback picture will be blurred at the switching point.  
Mode Button  
Tape Length Setting  
Set the tape length according to the length of the tape  
used.  
Select Dial  
Viewfinder  
Power Switch  
ACCESS MENU SCREEN  
1 First set the System Select Switch to “VIDEO”, then  
T30  
Tape length indicator  
set the Power Switch to “PRO.”. Press MENU.  
SP  
SELECT FUNCTION  
Recording mode  
indicator  
2 Rotate the Select Dial to move the highlight bar to  
TAPE LENGTH”, then press it. The TAPE LENGTH  
Setting Menu appears.  
SET TAPE LENGTH  
Display  
3 Rotate the Select Dial to move the highlight bar to the  
correct setting. T20=20 minutes of recording time,  
T30=30 minutes, and T40=40 minutes (in SP).  
Menu Screen  
4
NEXT  
M.W.B.  
AUTO  
ON  
D . ZOOM  
TELE MACRO OFF  
DATE TIME  
•If you decide you want to return the tape length to  
the previous setting, rotate the Select Dial to move  
the highlight bar to “EXIT”.  
TAPE LENGTH T30  
PICTURE  
FINE  
FULL  
SNAPSHOT  
4
RETURN  
CLOSE MENU SCREEN  
4 Press the Select Dial. The Menu Screen reappears  
TAPE LENGTH  
with the highlight bar on “RETURN”. Press the Select  
Dial again to close the Menu Screen.  
TAPE LENGTH  
Setting Menu  
T20  
T30  
T40  
NOTE:  
The tape remaining time (pg. 19) displayed in the  
viewfinder is correct only if the correct tape length has  
been selected.  
EXIT  
4
NEXT  
M.W.B.  
AUTO  
ON  
D . ZOOM  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T40  
PICTURE  
FINE  
FULL  
SNAPSHOT  
4RETURN  
EN15  
Cassette holder  
Loading/Unloading A Cassette  
OPEN LCD MONITOR  
1 Open the LCD monitor to an angle of over 60  
degrees.  
OPEN CASSETTE HOLDER  
2 Slide EJECT until the holder opens. Do not use force  
to open.  
INSERT/REMOVE CASSETTE  
3 Make sure the label is facing outward.  
PUSH Button  
EJECT Switch  
CLOSE CASSETTE HOLDER  
4 Press PUSH and make sure the holder is closed and  
locked.  
CLOSE LCD MONITOR  
5 First make sure the holder is closed. Then close the  
LCD monitor.  
Turn to take  
up slack.  
NOTES:  
Closing the LCD monitor while the cassette holder is still  
open may cause damage to the LCD monitor.  
The cassette holder can’t be opened unless a power  
supply is attached.  
Erase Protection  
Gear  
Make sure that the tape is not slack when loading the  
cassette. If there is any slack, turn the gear on the  
cassette in the direction of the arrow to take up the  
slack.  
Make sure the Erase Protection tab is in the position that  
allows recording. If not, slide the tab. Some cassettes  
have removable tabs. If the tab has been removed, cover  
the hole with adhesive tape.  
The cassette holder cannot be opened while the  
camcorder is in the record mode.  
GETTING STARTED (cont.)  
Grip Adjustment  
16  
EN  
Power Zoom Lever  
EXPAND LOOP  
1 Separate the Velcro strip.  
INSERT HAND  
2 Pass your right hand through the loop and grasp the  
grip.  
ADJUST STRAP LENGTH  
3 Adjust so your thumb and fingers can easily operate  
the Recording Start/Stop Button and Power Zoom  
Lever. Refasten the Velcro strip.  
Recording Start/Stop Button  
Viewfinder Adjustment  
SELECT OPERATION MODE  
3
1 Set the Power Switch to “CAMERA” (“AUTO” or  
“PRO.”).  
2
POSITION VIEWFINDER  
180°  
2 Adjust the viewfinder manually for best viewability  
(see illustration at left).  
ADJUST DIOPTER  
3 Turn the Diopter Adjustment Control until the  
indications in the viewfinder are clearly focused.  
1
Set “POWER” to  
“CAMERA”  
(“AUTO” or “PRO.”)  
PAUSE  
EN17  
Shoulder Strap Attachment  
ATTACH STRAP  
1 Following the illustration at left, thread the strap  
through the top of the eyelet 1, then fold it back and  
thread it through the buckle 2. Repeat the procedure  
to attach the other end of the strap to the other eyelet  
3, making sure the strap is not twisted.  
1
4
2
ADJUST LENGTH  
2 Adjust as shown in the illustration at left 4.  
3
Tripod Mounting  
ALIGN AND TIGHTEN  
1 Align the screw and camera direction stud on the  
tripod with the camera’s mounting socket and stud  
hole. Then tighten the screw.  
CAUTION:  
When using a tripod, be sure to open and extend  
its legs fully to stabilize the camcorder. To  
prevent damage to the unit caused by falling  
over, do not use a small-sized tripod.  
VIDEO RECORDING Basic Recording  
18  
EN  
System Select Switch  
LENS COVER  
Open/Close Ring  
NOTE:  
You should already have performed the procedures listed  
below. If not, do so before continuing.  
Power (pg. 10)  
Recording Mode Setting (pg. 14)  
Tape Length Setting (pg. 14)  
Grip Adjustment (pg. 16)  
Viewfinder Adjustment (pg. 16)  
LOAD A CASSETTE  
1 First open the LCD monitor to an angle of over 60  
degrees.  
Slide EJECT to open the cassette holder, then insert  
the cassette with the label facing out. Press PUSH to  
ensure the holder is closed and locked.  
Power Switch  
Recording Start/Stop Button  
EJECT Switch  
Shooting While Watching The Viewfinder  
Power lamp  
ENTER RECORD-STANDBY MODE  
2 Make sure the LCD monitor is closed and locked.  
Turn the LENS COVER Open/Close Ring to open the  
lens cover. Set the System Select Switch to “VIDEO”,  
then set the Power Switch to “CAMERA” (“AUTO” or  
“PRO.”).  
•The power lamp lights and the camcorder enters the  
Record-Standby mode.  
Tally lamp  
(lights while recording is in progress)  
•The scene you are aimed at appears on the  
viewfinder screen, with the word “PAUSE”  
superimposed upon it.  
START SHOOTING  
3 Press the Recording Start/Stop Button.  
•“  
” appears in the viewfinder while recording is  
in progress.  
Power Switch Position  
According to the Power Switch position you have selected, the following functions are available:  
AUTO  
(Full Auto mode):  
PRO.  
(PRO. mode):  
POWER OFF:  
Allows you to record using  
Allows you to set various  
recording functions using the  
menus. If you want more creative  
capabilities than full auto  
recording, try this mode.  
Allows you to switch off the  
camcorder.  
NO special effects or manual  
adjustments. Suitable for  
standard recording.  
EN19  
Tape remaining time indicator  
STOP RECORDING  
4 Press the Recording Start/Stop Button again to stop  
25MIN  
MIN  
(Now calculating)  
recording.  
The camcorder re-enters the Record-Standby mode.  
120MIN  
119MIN  
NOTES:  
When the Power Switch is set to CAMERA and the LCD  
monitor is opened at an angle of 60 degrees or more, the  
LCD monitor switches on and the viewfinder switches  
off automatically to save power.  
3MIN  
The cassette holder cannot be opened unless a power  
supply is attached.  
2MIN  
(Blinking)  
There may be a delay after you slide EJECT until the  
holder opens. Do not use force.  
The tape remaining time is only displayed in the  
viewfinder as shown.  
1MIN  
The remaining time indicated in the viewfinder is  
approximate.  
(Blinking)  
The time required to calculate the remaining tape  
length, and the accuracy of the calculation, may vary  
according to the type of tape used.  
0MIN  
(Blinking)  
The tape remaining time indicator is correct only if the  
correct tape length has been selected (pg. 14).  
“TAPE END” appears when the tape reaches its end, and  
the power goes off automatically if left in this condition  
for 5 minutes. “TAPE END” also appears when a cassette  
whose tape is already at its end is loaded.  
Recording Start/Stop Button  
If the Record–Standby mode continues for 5 minutes  
without performing Zoom or any other operations, the  
camcorder’s power shuts off automatically. Set the  
Power Switch to “POWER OFF”, and then back to  
“CAMERA” to turn the camcorder on again.  
If the Recording Start/Stop button is pressed after the  
Record-Standby mode has continued for over  
5 minutes, recording may not start immediately.  
If you are recording on a cassette from the middle (such  
as when a tape is removed and re-inserted during  
recording), use the Retake function (pg. 29) to find  
the end of the last recording so you don’t erase any of it.  
The LENS COVER warning blinks for about 5 seconds  
when the camcorder is turned on with the cover closed.  
While shooting, sound is not heard from the speaker.  
To turn the tally lamp off during recording, refer to pgs.  
36 and 38.  
DISPLAY Button  
LCD Monitor/Viewfinder Indications  
Press DISPLAY to make the following indications appear/  
disappear from the camcorder’s display: cassette warning,  
tape remaining time, battery pack remaining power  
indicator and tape length indicator (pg. 71).  
PRESS DISPLAY BUTTON  
1 To turn off the indications, press DISPLAY for more  
than 1 second.  
Press again for more than 1 second to make the  
indications reappear.  
NOTE:  
Even if the indications are off, the tape remaining time  
appears blinking when the tape is near its end, and the  
battery pack remaining power indicator appears blinking  
when the power is almost gone.  
VIDEO RECORDING Basic Recording (cont.)  
20  
EN  
Shooting While Watching The LCD Monitor  
Before the following steps, perform step 1 (pg. 18).  
90°  
180°  
ENTER RECORD–STANDBY MODE  
2 Make sure the LCD monitor is fully open. Turn the  
LENS COVER Open/Close Ring to open the lens  
cover. Set the System Select Switch to “VIDEO”,  
then set the Power Switch to “CAMERA” (“AUTO” or  
“PRO.”).  
The power lamp lights and the camcorder enters the  
Record-Standby mode.  
The scene you are aimed at appears in the LCD  
monitor, with the word “PAUSE” superimposed  
upon it.  
System Select Switch  
LENS COVER  
Open/Close Ring  
START SHOOTING  
3 Tilt the LCD monitor upward/downward for best  
viewability (pg. 21) and press the Recording Start/  
Stop Button.  
•“  
” appears in the LCD monitor while recording  
is in progress.  
STOP RECORDING  
4 Press the Recording Start/Stop Button again to stop  
Power Switch  
recording.  
The camcorder re-enters the Record-Standby mode.  
Recording Start/Stop Button  
Power lamp  
NOTES:  
When you use the LCD monitor outdoors in direct  
sunlight, the LCD monitor may be difficult to see. If this  
happens, we recommend that you use the viewfinder  
(pg. 18).  
To turn the tally lamp off during recording, refer to pgs.  
36 and 38.  
For other notes, refer to pg. 19.  
Tally lamp  
(lights while recording is in progress)  
EN21  
Journalistic Shooting  
In some situations different angles of shooting may be  
required for more dramatic results.  
OPEN LCD MONITOR  
1 Make sure the LCD monitor is fully open.  
TILT LCD MONITOR  
2 Tilt the LCD monitor in the most convenient  
direction.  
The LCD monitor can rotate almost full circle (270°:  
90° downward, 180° upward).  
Interface Shooting  
The person you shoot can view himself/herself in the  
LCD monitor, and you can even shoot yourself while  
viewing your own image in the LCD monitor.  
TILT LCD MONITOR UPWARD  
1 Open the LCD monitor and tilt it upward to 180  
Self-recording  
degrees so that it faces forward.  
When the LCD monitor is tilted upward to an angle  
of over approx. 105 degrees, the monitor image is  
inverted vertically, and the viewfinder also switches  
on.  
START RECORDING  
2 Point the lens toward the subject (yourself when self-  
recording) and start recording.  
During Interface Shooting, the monitor image and  
indications do not appear inverted as they would  
when viewing a mirror.  
NOTE:  
The monitored image can be viewed on the LCD monitor  
and in the viewfinder.  
Brightness Control  
You can adjust the brightness of the LCD monitor by  
turning the BRIGHT Dial.  
ADJUST BRIGHTNESS  
1 If you want to brighten the image . . .  
Turn the Dial towards “+”.  
If you want to darken the image . . .  
Turn the Dial towards “”.  
BRIGHT Dial  
DIGITAL STILL CAMERA (D.S.C.) SHOOTING  
22  
EN  
SNAPSHOT Button LENS COVER  
Basic Shooting  
Open/Close Ring  
When shooting a still image, it is not recorded onto the  
tape, but it is stored in the camcorder’s built-in memory in  
the selected Picture Mode. A stored still image data can be  
transferred to a PC, saved, and processed using a Paint  
Software program (pg. 53).  
System  
Select  
Switch  
MODE SELECTION  
SELECT OPERATION SYSTEM AND  
1 MODE  
Turn the LENS COVER Open/Close Ring to open the  
lens cover, then set the System Select Switch to  
“D.S.C.”. Set the Power Switch to “PRO.”.  
MENU Button  
Power lamp  
• The power lamp lights and an image appears.  
SELECT PICTURE MODE  
2 Do steps 2 and 3 of “OPERATION” on pg. 24.  
Set “PICTURE” to “FINE” or “STANDARD” in the  
Menu Screen as required.  
•There are two modes: FINE allows you to shoot up  
to approx. 30 still images with higher resolution,  
and STANDARD allows you to shoot up to approx.  
60 still images with lower resolution.  
Select Dial  
Display  
Power Switch  
Menu Screen  
4
NEXT  
M.W.B.  
AUTO  
ON  
SELECT SNAPSHOT MODE  
D . ZOOM  
TELE MACRO OFF  
DATE TIME  
3 Rotate the Select Dial to move the highlight bar to  
TAPE LENGTH T30  
“SNAPSHOT”, and press it. The SNAPSHOT Menu  
appears.  
PICTURE  
FINE  
SNAPSHOT  
FULL  
Rotate the Select Dial to move the highlight bar to the  
appropriate mode among the 5 Snapshot modes  
(pg. 23), and press it. Selection is complete.  
4
RETURN  
SNAPSHOT  
SNAPSHOT Menu  
CLOSE MENU SCREEN  
FULL  
PIN UP  
MULTI  
MULTI  
4 The Menu Screen reappears with the highlight bar on  
4
9
“RETURN”. Press the Select Dial again to close the  
Menu Screen.  
M.DRIVE  
STILL IMAGE STORAGE  
EXIT  
TAKE SNAPSHOT  
1 Press SNAPSHOT.  
Menu Screen  
4
NEXT  
M.W.B.  
AUTO  
ON  
D . ZOOM  
•Regardless of the Power Switch position (“AUTO”  
or “PRO.”), Snapshot recording takes place using  
the selected Snapshot mode.  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T30  
PICTURE  
FINE  
PIN-UP  
SNAPSHOT  
•A still image is stored in the built-in memory and  
displayed for approx. 2 seconds. While the still  
image remains displayed, that image is in the  
process of being stored in memory, and it is  
therefore impossible to take another shot during that  
time. When the still image disappears and the scene  
you are currently aimed at appears on the screen,  
you may take another shot.  
4RETURN  
Normal Screen  
During Snapshot mode  
P
No display  
(Full)  
(Pin-Up)  
P
•The remaining number of shots available is  
displayed.  
MD (M.DRIVE)  
M4 (MULTI-4)  
M9 (MULTI-9)  
EN23  
Remaining number  
of shots  
NOTES:  
The remaining number of shots varies according to the  
selected Picture Mode. In the “STANDARD” mode,  
twice as many still images can be shot as in the “FINE”  
mode.  
FINE 12  
30 29  
1
0
(Blinking)  
Some sample images have been stored in the built-in  
memory at the factory.  
If you wish to delete them, first remove the “Protect”  
function (pg. 57), then perform the “Delete” function  
(pg. 58).  
Pictrue mode  
display  
When the Power Switch is set to “AUTO”, it is not  
possible to select the Snapshot mode. You can use the  
Snapshot mode you selected in the “PRO.” mode.  
If a Snapshot is taken while the camcorder is in the  
WIDE mode (pg. 37), the Snapshot image is  
recorded without the black bars at the top and bottom of  
the screen.  
FULL*  
(Snapshot mode with  
no frame)  
PIN-UP*  
(Pin-Up mode)  
MULTI-4 **  
(Multi-Analyzer 4)  
MULTI-9**  
(Multi-Analyzer 9)  
* There is a momentary camera shutter-type blackout  
together with the image.  
** Continuous camera shutter-type blackout takes place 4  
or 9 times with the image, like serial photography, then  
the 4 or 9 still images you took are displayed.  
M. DRIVE 
ߛ
 
(Motor Drive mode)  
ߛ
 Stores 6 still images continuously for approx. 2 seconds.  
During still image storage, “MD” blinks and the 6 still  
images are displayed in the order that you took them.  
There is no sound effect of a shutter closing.  
CONTINUED ON NEXT PAGE  
D.S.C. SHOOTING (cont.)  
24  
EN  
SNAPSHOT Button  
FEATURE: Picture Mode Setting  
PURPOSE:  
There are two image settings you can choose from  
when storing in the camcorder's memory: FINE and  
STANDARD. FINE allows you to shoot up to approx.  
30 still images in a format based on JPEG (Joint  
Photographic Experts Group). Since the quality of  
image is better than “STANDARD”, “FINE” is more  
suitable for post-production on a PC. “STANDARD”  
allows you to shoot up to approx. 60 still images in a  
format based on JPEG (Joint Photographic Experts  
Group). Since in this mode, twice as many still images  
can be shot as in the “FINE” mode, select this mode  
when you wish to shoot many still images.  
System  
Select  
Switch  
MENU Button  
OPERATION:  
1) Turn the LENS COVER Open/Close Ring to open the  
lens cover, and set the System Select Switch to  
“D.S.C.”. Set the Power Switch to “PRO.”.  
2) Press MENU. The Menu Screen appears.  
If you wish the Picture Mode to return to the previous  
setting, rotate the Select Dial to move the highlight  
bar to “RETURN”.  
3) Rotate the Select Dial to move the highlight bar to  
“PICTURE”, and press it. The PICTURE Menu  
appears.  
Rotate the Select Dial to move the highlight bar to  
“FINE” or “STANDARD”, and press it. Selection is  
complete.  
4) The Menu Screen reappears with the highlight bar  
on “RETURN”. Press the Select Dial again to close  
the Menu Screen.  
Select Dial  
Display  
Power Switch  
Menu Screen  
4
NEXT  
M.W.B.  
AUTO  
ON  
D . ZOOM  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T30  
PICTURE  
FINE  
FULL  
SNAPSHOT  
4
RETURN  
PICTURE  
PICTURE Menu  
FINE  
STANDARD  
EXIT  
4
NEXT  
Menu Screen  
M.W.B.  
D . ZOOM  
AUTO  
ON  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T30  
PICTURE  
STD  
FULL  
SNAPSHOT  
4RETURN  
Normal Screen  
Remaining number  
of shots  
STD 12  
60  
59  
1
0
(Blinking)  
Picture mode display  
STD FINE  
EN25  
NOTES:  
The picture mode’s factory-preset is FINE.  
Some sample images have been stored in the built-in memory at the factory.  
If you wish to delete them, first remove the “Protect” function (pg. 57), then perform the “Delete”  
function (pg. 58).  
To store the still images you shot, we recommend that you transfer them to a computer and save them on  
disk (pg. 53), or transfer them to a VCR connected to the camcorder and record them onto a tape.  
When the Power Switch is set to “CAMERA” (“AUTO” or “PRO.”) and the LCD monitor is opened at an  
angle of 60 degrees or more, the LCD monitor switches on and the viewfinder switches off automatically  
to save power. When you use the LCD monitor outdoors in direct sunlight, the LCD monitor may be  
difficult to see. If this happens, we recommend that you use the viewfinder.  
When the remaining number indicator displays “0” (blinking), it is not possible to continue storing pictures  
until you delete some shots to make room for new ones. Perform “DELETE” function in the Menu Screen  
to remove pictures you do not need (pg. 58).  
The Picture Mode can be switched to either “FINE”or “STANDARD”. Since the remaining number of shots  
available depends on the selected Picture Mode, switching the Picture Mode will vary this number.  
The LENS COVER warning blinks for approx. 5 seconds when the camcorder is turned on with the cover  
closed.  
When SNAPSHOT is pressed with the System Select Switch set to “VIDEO”, the picture is stored in the  
camcorder's built-in memory (in the Snapshot mode selected in the “VIDEO” system) and also onto the tape  
(if a tape is in the camcorder) (pg. 26).  
When you shoot in a dark environment, the still image will become coarse and its true colors will be lost.  
RECORDING Basic Features  
26  
EN  
LENS COVER  
Open/Close Ring  
Snapshot  
SNAPSHOT Button  
This interesting feature lets you record two types of digital  
still images that look like photographs onto a tape, as well  
as keeping them in the camcorder’s built-in memory. It is a  
great way to spice up footage of events such as parties,  
weddings and graduations.  
SNAPSHOT MODE SELECTION  
SELECT OPERATION SYSTEM AND  
1 MODE  
Turn the LENS COVER Open/Close Ring to open the  
lens cover, and set the System Select Switch to  
“VIDEO”. Set the Power Switch to “PRO.”  
System Select Switch  
MENU Button  
•The power lamp lights and the camcorder enters  
Record-Standby mode.  
Power lamp  
SELECT SNAPSHOT MODE  
2 Press MENU. The Menu Screen appears.  
Rotate the Select Dial to move the highlight bar to  
“SNAPSHOT”, and press it. SNAPSHOT Menu  
appears.  
Rotate the Select Dial to move the highlight bar to  
“FULL” or “PIN-UP”, and press it. Selection is  
complete.  
Select Dial  
Display  
Power Switch  
Menu Screen  
CLOSE MENU SCREEN  
4
NEXT  
3 The Menu Screen reappears with the highlight bar on  
M.W.B.  
AUTO  
ON  
D . ZOOM  
“RETURN”. Then press the Select Dial to close the  
Menu Screen.  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T30  
PICTURE  
FINE  
SNAPSHOT  
FULL  
4RETURN  
SNAPSHOT  
SNAPSHOT Menu  
FULL  
PIN UP  
EXIT  
Menu Screen  
4
NEXT  
M.W.B.  
AUTO  
ON  
D . ZOOM  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T30  
PICTURE  
FINE  
PIN-UP  
SNAPSHOT  
4RETURN  
P
(Pin-Up)  
P
No display  
(Full)  
EN27  
SNAPSHOT  
SNAPSHOT RECORDING  
TAKE SNAPSHOT  
1 Press SNAPSHOT.  
Display (ex. Pin-Up)  
Regardless of the Power Switch position (“AUTO”  
or “PRO.”), Snapshot recording takes place using  
the selected Snapshot mode.  
•A still image is recorded onto the tape and into the  
camcorder’s built-in memory.  
First there is a momentary camera shutter-type  
blackout together with the sound effect of a shutter  
closing, then a still image appears. The scene you  
are currently aimed at starts in the center of a black  
screen and wipes in toward the corners.  
The screen changes as shown in the illustrations 1  
to 5 and the screens 1 to 5 are recorded onto the  
tape in the selected mode. Only the still image 3 is  
stored in the built-in memory in the selected mode,  
then the camcorder resumes normal recording.  
1
2
3
4
5
If you press during Record-Standby mode . . .  
.... the screens 1 to 3 are recorded onto the tape in  
the selected mode. Then the camcorder re-enters  
the Record-Standby mode.  
NOTES:  
When the remaining number indicator displays “0”  
(blinking), the still image will be recorded onto the  
tape but not in the built-in memory. If you wish to store  
a still image in the built-in memory, pg. 58.  
The Picture Mode can be switched to either “FINE” or  
“STANDARD”. Since the remaining number of shots  
available depends on the selected Picture Mode,  
switching the Picture Mode will vary this number.  
If SNAPSHOT is pressed with the System Select Switch  
set to “D.S.C.”, pg. 22.  
Image data stored in the camcorder’s built-in memory  
can be transferred to a Windows® PC and saved using  
the provided image transfer software, Picture Navigator  
(pg. 53). The image data transferred to a Windows®  
PC can also be further processed using Mr. Photo  
Gold.  
If a snapshot is taken while the camcorder is in the  
WIDE mode (pg. 37), the snapshot image is  
recorded without the black bars at the top and bottom  
of the screen.  
FULL  
(Snapshot mode with  
no frame)  
When a Snapshot is taken in a dark environment, the  
still image recorded onto the tape and stored in  
memory will become coarse and its true colors will be  
lost.  
PIN-UP  
(Pin-Up mode)  
RECORDING Basic Features (cont.)  
28  
EN  
FEATURE: Zooming  
Zoom in  
PURPOSE:  
To produce the zoom in/out effect, or an instantaneous  
change in image magnification.  
Digital circuitry extends the maximum magnification  
offered by optical zoom. This system is called Digital  
Zoom.  
Zoom out  
OPERATION:  
Zoom In  
Push the Power Zoom Lever towards “T”.  
Zoom Out  
Display  
Push the Power Zoom Lever towards “W”.  
The quicker you push the Power Zoom Lever, the  
quicker the zoom action.  
Zoom indicator bar  
Zoom level indicator  
1X  
NOTES:  
Focusing may become unstable during Zooming. In  
this case, set the zoom while in Record–Standby,  
lock the focus by using the manual focus  
(pg. 41), then zoom in or out in Record mode.  
The zoom level indicator (5) moves during zoom.  
Once the zoom level indicator reaches the top of  
the zoom indicator bar, all magnification from that  
point is through digital processing.  
Approximate zoom ratio  
Power Zoom Lever  
When using Digital Zoom, the quality of image may  
suffer. To deactivate Digital Zoom, set “D.ZOOM”  
to “OFF” in the Menu Screen (pg. 37).  
Power Switch  
EN29  
P. STABILIZER Button  
FEATURE: Quick Review  
PURPOSE:  
To check the end of the last recording.  
OPERATION:  
1) Press “ ” and release quickly during the Record–  
Standby mode.  
Tape is rewound for about 2 seconds and played  
back automatically, then pauses in Record–Standby  
mode for the next shot.  
NOTE:  
Distortion may occur at the start of playback. This is  
normal.  
FEATURE: Retake  
RETAKE (R/F) Button  
PURPOSE:  
To re-record certain segments.  
OPERATION:  
1) Make sure the camcorder is in the Record–Standby  
mode.  
2) Press either RETAKE to reach the start point for new  
recording. Pressing “F” forwards the tape and  
pressing “R” reverses it.  
Display  
3) Press the Recording Start/Stop Button to start  
recording.  
Picture stabilizer  
indicator  
NOTE:  
Noise bars appear and pictures may become  
monochrome or darken during Retake. This is normal.  
FEATURE: Picture Stabilizer  
PURPOSE:  
To compensate for unstable images caused by camera-  
shake, particularly at high magnification.  
OPERATION:  
1) Press P. STABILIZER. “  
”appears.  
To switch off the Picture Stabilizer, press  
P. STABILIZER. The indicator disappears.  
NOTES:  
Accurate stabilization may not be possible if hand  
shake is excessive, or under the following conditions:  
When shooting subjects with vertical or horizontal  
stripes.  
When shooting dark or dim subjects.  
When shooting subjects with excessive backlighting.  
When shooting scenes with movement in various  
directions.  
When shooting scenes with low-contrast backgrounds.  
Switch off the Picture Stabilizer when recording  
with the camcorder on a tripod.  
The “  
” indicator appears blinking if the  
Stabilizer cannot be used.  
RECORDING Basic Features (cont.)  
30  
EN  
FEATURE: Video Light  
PURPOSE:  
To brighten the scene when natural lighting is too dim.  
OPERATION:  
1) Set the LIGHT OFF/AUTO/ON Switch as required:  
OFF : Turns off the light.  
AUTO : Automatically turns on the light when the  
camcorder senses insufficient lighting on the  
subject.  
ON  
: Always keeps the light on as long as the  
camcorder is turned on.  
LIGHT OFF/AUTO/ON Switch  
The video light can only be used with the  
camcorder’s power on.  
It is recommended to set the white balance  
(pg. 42) to  
when you use the video light.  
When not using the video light, turn it off to save  
battery power.  
DANGER  
NOTES:  
The video light can become extremely  
hot. Do not touch it either while in  
operation or soon after turning it off,  
otherwise serious injury may result.  
Do not place the camcorder into the  
carrying case immediately after using the  
video light, since it remains extremely  
hot for some time.  
Even if the battery indicator (  
) does not blink if  
the battery pack’s charge is low, the camcorder may  
turn off automatically when you turn on the video  
light, or when you start recording with the video light  
turned on.  
When the LIGHT OFF/AUTO/ON Switch is set to  
“AUTO”:  
When operating, keep a distance of  
about 30 cm. (1 ft.) between the video  
light and people or objects.  
Do not use near flammable or explosive  
materials.  
It is recommended that you consult your  
nearest JVC dealer for replacing the video  
light.  
Depending on the lighting conditions, the video  
light may keep turning on and off. In this case,  
manually switch the light on or off using the  
LIGHT OFF/AUTO/ON switch.  
While the “Sports” or “High Speed Shutter” mode  
(pg. 33) is engaged, the light is likely to stay on.  
While the “Twilight” mode (pg. 33) is engaged,  
the light will not activate.  
RECORDING Advanced Features  
EN31  
[Ex.: Fader]  
Fade in  
Fade/Wipe  
These effects let you make pro-style scene transitions.  
Fade- or wipe-in works at recording start, and fade- or  
wipe-out works at recording end or when you enter  
Record–Standby mode.  
SELECT OPERATION SYSTEM AND  
1 MODE  
Fade out  
Set the System Select Switch to "VIDEO", and set the  
Power Switch to “PRO.”.  
Display  
After 2 sec.  
ENGAGE FADE- OR WIPE-STANDBY  
2 MODE  
MOSAIC  
Press EFFECT to cycle through the modes as shown at  
left. Once the desired mode appears, it is selected  
and reserved.  
The selected mode’s name and its indication are  
displayed for approx. 2 seconds. Then the name  
disappears, and only the indication remains.  
START OR END RECORDING  
FADER  
MOSAIC  
SHUTTER  
SLIDE  
3 Press the Recording Start/Stop Button to activate fade-  
in/out or wipe-in/out.  
TO CANCEL FADE- OR WIPE-STANDBY  
4 MODE  
Press EFFECT repeatedly until “OFF” appears.  
OFF” is displayed for approx. 2 seconds and the  
fade/wipe standby mode is canceled.  
OFF  
OFF  
(No indication)  
FADER  
Fades in/out to a black screen.  
System Select Switch  
EFFECT Button  
MOSAIC (Fader)  
Gradually turns/returns the picture into/from a mosaic  
pattern.  
SHUTTER (Wipe)  
A black screen moves in from the top and bottom, closing  
over the image like a shutter, or a new image pushes open  
the black screen vertically from the center.  
SLIDE (Wipe)  
A black screen moves in from the left to gradually cover  
the image, or a new image moves in from right to left.  
Recording Start/Stop  
Button  
Power Switch  
NOTES:  
Pressing and holding the Recording Start/Stop Button allows you to vary the length for the image during fade  
in/out or wipe in/out.  
The screen becomes slightly reddish when the Fade/Wipe is used with Sepia (pg. 33).  
With the Electronic fog filter mode (pg. 33) engaged, the image fades in/out to a white screen.  
Even if you start shooting with the Fade/Wipe indication displayed during Digital Still Camera Shooting, the  
Fade/Wipe does not function.  
RECORDING Advanced Features (cont.)  
32  
EN  
Display  
SEPIA  
Program AE With Special Effects  
After 2 sec.  
All you have to do to access any of the variety of shooting  
:
effects is press P.AE.  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “D.S.C.” or “VIDEO”,  
and set the Power Switch to “PRO.”.  
SELECT MODE  
2 Press P.AE to cycle through the modes as shown on  
the left.  
SEPIA  
•The selected mode’s name and its indication are  
displayed for approx. 2 seconds. Then the name  
disappears, and only the indication remains. The  
mode is activated.  
SPORTS  
:
ND ND EFFECT  
ND  
FG  
NOTES:  
:
FG FOG  
TWILIGHT  
Only one mode can be engaged at a time.  
The screen becomes slightly reddish when the Fade/  
Wipe (pg. 31) is used in the Sepia mode.  
The screen becomes slightly dark in the High Speed  
Shutter mode. Use in well-lit situations.  
S1/2000  
In the “High Speed Shutter” or “Sports” modes, picture  
color may be adversely affected if the subject is lit by  
alternating discharge-type light sources such as  
flourescent or mercury-vapor lights.  
NEGA/POSI  
OFF  
OFF  
(No indication)  
P.AE Button  
Power Switch  
System Select Switch  
EN33  
Display  
Mode  
Display  
Mode  
Sepia  
Twilight  
SEPIA  
TWILIGHT  
Sepia  
Twilight  
The scene being shot is recorded in sepia-tinted  
(reddish-brown) monochrome, giving the effect of  
an older movie. Use together with Wide (pg. 37)  
for the authentic look of a classic Hollywood  
movie.  
Dusk, twilight scenery, fireworks, etc., look more  
natural and dramatic. The following happens when  
Twilight mode is selected:  
•Auto gain control is turned off.  
•White Balance is set to “  
” (FINE day mode),  
When the Power Switch is set to “D.S.C.”, the  
scene is stored in black-and-white in the  
camcorder’s memory.  
but can also be manually changed to another  
mode (pg. 42).  
•Auto Focus becomes available only in the range of  
10 m (33 ft.) to infinity. To focus when the subject-  
to-camera distance is less than 10 m (33 ft.), use  
manual focusing (pg. 41).  
Sports  
SPORTS  
1/2000 sec.  
High Speed Shutter  
Sports  
S1/2000  
.
High shutter speed clearly captures fast-moving  
action.  
High-Speed Shutter (1/2000s.)  
Captures faster action than Sports mode.  
ND Effect  
:
ND ND EFFECT  
Nega/Posi  
NEGA POSI  
ND Effect  
A black mist darkens the picture, as when an ND  
filter is used. Helps to counter the effects of glare on  
the subject.  
Nega/Posi (Negative/Positive)  
The colors of a picture are reversed.  
Electronic  
Fog Filter  
:
FG FOG  
Electronic Fog Filter  
Makes the picture look misty white, as when an  
external fog filter is attached to the lens. Softens the  
image and gives it a “fantasy” look.  
NEGA POSI mode  
RECORDING Advanced Features (cont.)  
34  
EN  
Date/Time Insert  
This feature allows you to display the date and time on the  
LCD monitor, in the viewfinder, or on a connected color  
monitor, as well as to record them manually or  
automatically.  
System  
Select  
Switch  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “VIDEO”, and set the  
Power Switch to “PRO.”.  
ACCESS MENU SCREEN  
2 Press the Select Dial to display the Menu Screen.  
ACCESS “DATE/TIME DISP.” MENU  
3 Move the highlight bar to “DATE/TIME DISP.” by  
rotating the Select Dial while in Record-Standby.  
Then press it to display the DATE/TIME DISP. Menu.  
Select Dial  
Display  
Power Switch  
Menu Screen  
SELECT THE DESIRED MODE  
4 Move the highlight bar to the desired mode by  
FOCUS  
AUTO  
AUTO  
OFF  
rotating the Select Dial, then press it. The desired  
mode is activated.  
EXPOSURE  
WIDE  
S . LX  
OFF  
TITLE  
DATE TIME DISP.  
•You should have already performed the Date/Time  
Setting procedure (pg. 13). If you haven’t, do so  
first.  
4
RETURN  
CLOSE MENU SCREEN  
DATE TIME DISP.  
5 The Menu Screen reappears with the highlight bar on  
DATE/TIME DISP.  
Menu  
AUTO DATE  
DATE  
“RETURN”. Then press the Select Dial to close the  
Menu Screen.  
TIME  
DATE&TIME  
OFF  
NOTES:  
DISPLAY  
EXIT  
The selected display can be recorded.  
If you do not want to record the display, select the OFF  
mode before shooting.  
FOCUS  
EXPOSURE  
WIDE  
AUTO  
AUTO  
OFF  
Even if you shoot with the date/time displayed during  
Digital Still Camera Shooting, they will not be recorded.  
S . LX  
OFF  
TITLE  
DATE TIME DISP.  
AUTO DATE  
Your camcorder automatically records the date for about  
5 seconds after recording is initiated in the following  
situations:  
4
RETURN  
After changing the date.  
After loading a cassette.  
After Auto Date Record mode is selected by rotating  
the Select Dial.  
In this mode, the date is replaced after 5 seconds with  
“AUTO DATE” but this is not recorded.  
DEC 25 . 99  
AUTO DATE  
DEC 25 . 99  
(DATE)  
AM 10 : 25 : 00  
(TIME)  
DEC 25 . 99 AM 10 : 25 : 00  
(DATE&TIME)  
OFF  
(No indication)  
EN35  
Instant Titles  
The camcorder has eight preset titles in memory. You can  
superimpose one of them above a previously stored title as  
shown in the illustration to the left.  
System  
Select  
Switch  
Instant Titles can be displayed not only in English but also  
in French, Spanish and Portuguese. Change the setting in  
TITLE LANG. in the Menu Screen. (pg. 36, 38).  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “VIDEO”, and set the  
Power Switch to “PRO.”.  
ACCESS MENU SCREEN  
2 Press the Select Dial to display the Menu Screen.  
ACCESS “TITLE” MENU  
3 Move the highlight bar to “TITLE” by rotating the  
Select Dial while in Record-Standby. Then press it to  
display the TITLE Menu.  
Select Dial  
Display  
AUTO  
Power Switch  
Menu Screen  
SELECT THE DESIRED MODE  
4 Move the highlight bar to the desired mode by  
rotating the Select Dial, then press it. The desired  
mode is activated.  
FOCUS  
EXPOSURE  
WIDE  
AUTO  
OFF  
If you wish to make the title indication disappear,  
select “OFF”.  
S . LX  
TITLE  
OFF  
DATE TIME DISP.  
CLOSE MENU SCREEN  
4
RETURN  
5 The Menu Screen reappears with the highlight bar on  
“RETURN”. Then press the Select Dial to close the  
Menu Screen.  
TITLE  
TITLE Menu  
OFF  
HAPPY BIRTHDAY  
OUR VACATION  
MERRY CHRISTMAS  
A SPECIAL DAY  
HAPPY HOLIDAYS  
OUR NEW BABY  
WEDDING DAY  
CONGRATULATIONS  
EXIT  
NOTE:  
Even if you shoot with the Title displayed during Digital  
Still Camera Shooting, this is not recorded.  
FOCUS  
EXPOSURE  
WIDE  
AUTO  
AUTO  
OFF  
S . LX  
OFF  
TITLE  
DATE TIME DISP.  
4RETURN  
CONGRATULATIONS  
RECORDING Advanced Features (cont.)  
36  
EN  
Using Menu For Detailed Adjustment  
This camcorder is equipped with an easy-to-use,  
on-screen menu system that simplifies many of the more  
detailed camcorder settings.  
System Select Switch  
SELECT OPERATION SYSTEM AND MODE  
1 The operation system depends on the function you wish  
to select.  
Set the System Select Switch to “VIDEO” or “D.S.C.”  
according to each function's “*/**” explanation  
described at the bottom of pages 37 and 38, and set the  
Power Switch to “PRO.”.  
Select Dial  
MENU Button  
Menu Screen 1  
ACCESS MENU SCREEN  
Display  
(ex. Menu Screen available  
using the MENU Button)  
2 Menu access depends on the function you select.  
If you select the functions from the “Menu Screen  
Available Using The Select Dial” described on pg. 37 . . .  
.... press the Select Dial. The Menu Screen appears.  
4
NEXT  
M.W.B.  
AUTO  
ON  
If you select the functions from the “Menu Screen  
Available Using The MENU Button” described on  
pg. 37 and 38 . . .  
D . ZOOM  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T30  
.... press MENU. The Menu Screen appears.  
PICTURE  
FINE  
FULL  
SNAPSHOT  
SELECT FUNCTION  
4
RETURN  
3 Rotate the Select Dial to place the highlight bar on the  
desired function.  
Menu Screen 2  
4
BACK  
To go from Menu Screen 1 to Menu Screen 2, rotate the  
Select Dial to “NEXT” and press it. To go back to Menu  
Screen 1 from Menu Screen 2, rotate the Select Dial to  
“BACK”, and press it.  
If the setting you want cannot be found in the Menu Screen,  
place the highlight bar on “RETURN”, then go to step 6.  
REC. TIME  
INT. TIME  
OFF  
OFF  
TALLY LAMP ON  
TITLE LANG. ENGLISH  
JLIP ID NO  
06  
DEMO MODE OFF  
4
RETURN  
MAKE SETTING  
4 Press the Select Dial. The setting procedure depends on  
the function you select.  
TITLE LANG.  
Setting Menu  
(ex. TITLE LANG.)  
If you select “FOCUS”, “EXPOSURE”, “TITLE”, “DATE/  
TIME DISP.”, “DATE/ TIME”, “PICTURE” or "SNAP-  
SHOT". . .  
.... see respective pages (FOCUS: pg. 40, 41,  
EXPOSURE: pg. 39, TITLE: pg. 35,  
DATE/TIME DISP.: pg. 34, DATE/TIME: pg. 13,  
PICTURE: pg. 24, SNAPSHOT: pg. 22, 27).  
If you select “WIDE”, “D.ZOOM”, “TELE MACRO” or  
“DEMO MODE” . . .  
ENGLISH  
FRENCH  
SPANISH  
PORTUGUESE  
EXIT  
.... the selected function’s parameter starts blinking.  
Rotate the Select Dial until the desired parameter  
appears. Go to step 5.  
4
BACK  
REC. TIME  
INT. TIME  
OFF  
OFF  
TALLY LAMP ON  
If you select “JLIP ID NO.” . . .  
TITLE LANG. FRENCH  
JLIP ID NO  
06  
.... press the Select Dial so that the number blinks, then  
rotate it until the desired number appears, and press  
it. Then rotate the Select Dial to move the highlight  
bar to “EXIT”.  
DEMO MODE OFF  
4RETURN  
If you select any other functions . . .  
.... rotate the Select Dial to move the highlight bar to the  
desired setting.  
Normal Screen  
• If you decide you want to return to the previous setting,  
rotate the Select Dial to move the highlight bar to “EXIT”.  
END SETTING  
NOTE:  
5 Press the Select Dial. The Menu Screen reappears with  
No menu functions except “FOCUS” and  
“EXPOSURE” are available while in the Record  
mode.  
the highlight bar on “RETURN”.  
CLOSE MENU SCREEN  
6 Press the Select Dial. The normal screen reappears.  
EN37  
MENU SCREEN EXPLANATIONS  
Menu Screen Available Using The Select Dial  
Adjusts focus automatically.  
FOCUS  
AUTO  
MANU  
AUTO  
MANU  
OFF  
Allows you to adjust focus manually (pg. 40, 41).  
Adjusts exposure automatically.  
EXPOSURE  
WIDE  
Allows you to adjust exposure manually (pg. 39).  
Does not display black bars.  
Allows you to record black bars at the top and bottom of the screen  
to produce a cinema-like “wide-screen” effect.  
ON  
If a snapshot (pg. 22, 26) is taken while the camcorder is in  
the WIDE mode, the snapshot image is recorded without the  
black bars at the top and bottom of the screen.  
To record a subject in a darkly lit environment, when it is more  
convenient to shoot the subject with a brighter image even if the  
picture becomes slightly coarse.  
S.LX  
MAX  
To record a subject in a dimly lit environment, when it is more  
convenient to shoot with a less coarse picture although the  
subject becomes slightly dark. This setting is suitable for  
measuring sensitivity conforming to EIA-639 (EIA* Standard for  
Low Light Sensitivity Measurement).  
NORMAL  
*EIA : Electronic Industries Alliance  
Allows you to shoot dark scenes with no picture brightness  
adjustment.  
OFF  
TITLE*  
Allows you to superimpose one of eight preset titles (pg. 35).  
DATE/TIME  
DISP.*  
Makes the date/time settings appear in the camcorder or on a connected monitor  
(pg. 34).  
Menu Screen Available Using The MENU Button  
This Menu Screen cannot be accessed while recording.  
AUTO  
: FINE  
This camcorder’s Automatic Color Temperature system senses  
the color temperature of the ambient lighting for automatic  
white balance adjustment. However, precise color adjustment is  
not possible under the following conditions:  
M.W.B.  
: CLOUD  
• When an object is in various shades of the same color.  
• When a predominantly red or brown object is being shot outdoors.  
: HALOGEN  
In these cases, use the camcorder’s built-in preset filters for  
white balance adjustment (pg. 42, 43).  
MWB  
D. ZOOM  
ON  
Allows you to use the Digital Zoom. By digitally processing and  
magnifying images, zooming is possible from 16 times (the optical  
zoom limit), to a maximum of 380 times digital magnification.  
OFF  
Digital Zoom is not available. Only optical zoom (maximum  
16x magnification) can function. When set to “OFF” during  
Digital Zoom, zoom magnification changes to 16x.  
* Activated only with the System Select Switch set to “VIDEO”. If the System Select Switch is set to “D.S.C.”,  
this function will not be activated although the highlight bar will move on the Menu Screen like the setting  
procedure.  
Functions listed without an asterisk are available with the System Select Switch set to either “D.S.C.” or  
“VIDEO”.  
: Factory-preset  
CONTINUED ON NEXT PAGE  
RECORDING Advanced Features (cont.)  
Menu Screen Available Using The MENU Button (cont.)  
38  
EN  
TELE MACRO  
OFF  
ON  
Usually the distance to a subject where the lens is in focus  
depends on the zoom magnification. Unless there is a distance of  
more than 1m (3.3 ft.) to the subject, the lens is out of focus at the  
maximum telephoto setting. When set to “ON”, you can shoot a  
subject as large as possible at a distance of approx. 60 cm (2 ft.).  
Depending on the zoom position, the lens may go out of focus.  
DATE/TIME  
Allows you to set the current date and time (pg. 13).  
TAPE LENGTH* Allows you to set the tape length depending on the tape used (pg. 14).  
Allows you to select the image setting “FINE” or “STD” when storing in the  
camcorder's memory (pg. 24).  
PICTURE**  
SNAPSHOT  
FULL  
Displayed with the System Select Switch set to either “VIDEO”  
(pg. 26) or “D.S.C.” (pg. 23).  
PIN-UP  
MULTI-4  
MULTI-9  
M.DRIVE  
Displayed only with the System Select Switch set to “D.S.C.”  
(pg. 23).  
REC TIME*  
INT. TIME  
This feature allows you to set the parameters for Animation and Time-Lapse  
recording (pg. 45).  
This feature allows you to set the parameters for Self-Timer (pg. 44) and Time-  
Lapse recording (pg. 45).  
TALLY LAMP*  
OFF  
ON  
The tally lamp remains off at all times.  
The tally lamp comes on to signal the start of recording.  
Allows you to select the language (ENGLISH, FRENCH, SPANISH or PORTUGUESE)  
TITLE LANG.*  
JLIP ID NO.  
of Instant Titles (pg. 35).  
This number is necessary when connecting the camcorder to a device such as a computer  
using the J terminal (JLIP). The numbers range from 01 to 99. Factory setting is 06.  
Automatic demonstration will not take place.  
DEMO MODE*  
OFF  
ON  
Demonstrates certain functions such as Fade/Wipe, etc. When  
“DEMO MODE” is set to “ON” and the Menu Screen is closed,  
the demonstration starts.  
NOTES:  
When a tape whose Erase Protection tab is in the position that  
allows recording is loaded in the camcorder, demonstration is  
not available.  
By turning off the camcorder or inserting a tape whose Erase  
Protection tab is in the position that allows recording into it,  
“DEMO MODE” is set to “OFF” automatically.  
During the demonstration, all functions except zoom are  
disabled.  
* Activated only with the System Select Switch set to “VIDEO”. If the System Select Switch is set to “D.S.C.”,  
this function will not be activated although the highlight bar will move on the Menu Screen like the setting  
procedure.  
** Activated only with the System Select Switch set to “D.S.C.”. If the System Select Switch is set to “VIDEO”,  
this function will not be activated although the highlight bar will move on the Menu Screen like the setting  
procedure.  
Functions listed without an asterisk are available with the System Select Switch set to either “D.S.C.” or  
“VIDEO”.  
: Factory-preset  
EN39  
Exposure Control  
This feature automatically adjusts the iris for the best  
available picture quality, but you can override and make  
the adjustment manually.  
System  
Select Switch  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “D.S.C.” or “VIDEO”,  
and set the Power Switch to “PRO.”.  
ACCESS MENU SCREEN  
2 Press the Select Dial to display the Menu Screen.  
ACCESS “EXPOSURE” MENU  
3 Rotate the Select Dial to move the highlight bar to  
“EXPOSURE” and press it.  
ACCESS MANUAL EXPOSURE  
4 Rotate the Select Dial to move the highlight bar to  
Select Dial  
Display  
Power Switch  
Menu Screen  
“MANU”, then press it. “00” (exposure control level  
counter) appears.  
ADJUST EXPOSURE  
5 To brighten the image . . .  
.... rotate the Select Dial upward. The exposure  
control level counter increases (maximum +06).  
FOCUS  
AUTO  
AUTO  
OFF  
EXPOSURE  
WIDE  
S . LX  
TITLE  
OFF  
Go to step 6.  
To darken the image . . .  
DATE TIME DISP.  
.... rotate the Select Dial downward. The exposure  
control level counter decreases (maximum –06).  
4RETURN  
Go to step 6.  
EXPOSURE  
EXPOSURE Menu  
END ADJUSTMENT OF EXPOSURE  
AUTO  
MANU  
6 Press the Select Dial. The Menu Screen reappears  
with the highlight bar on “RETURN”.  
CLOSE MENU SCREEN  
7 Press the Select Dial. The Menu Screen disappears  
EXIT  
and the exposure control level counter reappers to  
indicate the exposure is adjusted.  
Manual Exposure  
Screen  
NOTES:  
00  
To return to the factory setting, select “AUTO” in step 4.  
To re-adjust exposure, repeat the procedure from step 2.  
Exposure control  
level counter  
To brighten the image  
+
06  
06  
To darken the image  
RECORDING Advanced Features (cont.)  
40  
EN  
Focus detection zone  
Focusing  
AUTO FOCUS  
The camcorder’s Full Range AF system offers continuous  
shooting ability from close-up to infinity. However, correct  
focus may not be obtainable in the situations listed below  
(in these cases use manual focusing):  
When two subjects overlap in the same scene.  
When illumination is low.*  
When the subject has no contrast (difference in bright-  
ness and darkness), such as a flat, one-color wall, or a  
clear, blue sky.*  
When a dark object is barely visible in the viewfinder.*  
When the scene contains minute patterns or identical  
patterns that are regularly repeated.  
When the scene is affected by sunbeams or light  
reflecting off the surface of a body of water.  
When shooting a scene with a high-contrast background.  
* The low-contrast warning “  
” appears.  
NOTES:  
If the lens is smeared or blurred, accurate focusing is not  
possible. Keep the lens clean, wiping with a piece of soft  
cloth if it gets dirty. When condensation occurs, wipe  
with a soft cloth or wait for it to dry naturally.  
When shooting a subject close to the lens, zoom out first  
(pg. 28). If zoomed in in the auto focus mode, the  
camcorder could automatically zoom out depending on  
the distance between the camcorder and the subject.  
When Tele Macro (pg. 38) is activated, the  
camcorder will not zoom out automatically.  
EN41  
MANUAL FOCUS  
NOTE:  
You should already have made the necessary viewfinder  
adjustments (pg. 16). If you haven’t, do so before  
continuing.  
System  
Select Switch  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “D.S.C.” or “VIDEO”,  
and set the Power Switch to “PRO.”.  
ACCESS MENU SCREEN  
2 Press the Select Dial to display the Menu Screen.  
ACCESS “FOCUS” MENU  
3 Move the hightlight bar to “FOCUS” by rotating the  
Select Dial, then press it.  
ACCESS MANUAL FOCUS  
Select Dial  
Display  
Power Switch  
Menu Screen  
4 Rotate the Select Dial to move the highlight bar to  
“MANU”, then press it. “ ” and “ ” appear. The  
focus is locked at this point.  
ADJUST FOCUS  
FOCUS  
AUTO  
AUTO  
OFF  
5 To farther subject . . .  
EXPOSURE  
WIDE  
.... rotate the Select Dial upward. “ ” appears and  
S . LX  
TITLE  
OFF  
blinks.  
DATE TIME DISP.  
Go to step 6.  
To nearer subject . . .  
4RETURN  
.... rotate the Select Dial downward. “ ” appears  
and blinks.  
FOCUS  
FOCUS Menu  
Go to step 6.  
AUTO  
MANU  
END ADJUSTMENT OF FOCUS  
6 Press the Select Dial. The Menu Screen reappears  
with the highlight bar on “RETURN”.  
EXIT  
CLOSE MENU SCREEN  
7 Press the Select Dial. The Menu Screen disppears and  
” reappears to indicate the focus is locked.  
Manual Focus Screen  
NOTES:  
To return to Auto Focus, select “AUTO” in step 4.  
To re-adjust Manual Focus, repeat the procedure from  
step 2.  
Be sure to focus the lens in the maximum telephoto  
position when you use the Manual Focus mode. If you  
focus in on a certain subject in the wide-angle position,  
sharply focused images cannot be obtained when  
zoomed in because the depth-of-field is reduced at  
longer focal lengths.  
When the focus level cannot be adjusted any farther or  
closer, “ ” or “ ” will blink.  
RECORDING Advanced Features (cont.)  
42  
EN  
White Balance Adjustment  
A term that refers to the correctness of color reproduction  
under various lighting. If the white balance is correct, all  
other colors will be accurately reproduced.  
System  
Select Switch  
The white balance is usually adjusted automatically.  
However, the more advanced camcorder operator would  
prefer to control this function manually and achieve a  
more professional color/tint reproduction.  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “D.S.C.” or “VIDEO”,  
and set the Power Switch to “PRO.”.  
MENU Button  
ACCESS MENU SCREEN  
2 Press MENU. The Menu Screen appears.  
ACCESS WHITE BALANCE  
3 ADJUSTMENT  
Move the highlight bar to “M.W.B.” by rotating the  
Select Dial, then press it. The Menu Screen disap-  
pears and the M.W.B. Menu appears.  
Select Dial  
Display  
Power Switch  
Menu Screen  
SET FUNCTION PARAMETERS  
4 Move the highlight bar to the required white balance  
4
NEXT  
by rotating the Select Dial.  
M.W.B.  
AUTO  
ON  
D . ZOOM  
AUTO”  
TELE MACRO OFF  
DATE TIME  
The white balance is adjusted automatically. This is  
the factory preset position.  
TAPE LENGTH T30  
PICTURE  
FINE  
FULL  
SNAPSHOT  
: FINE”  
When shooting outdoors on a sunny day.  
: CLOUD”  
When shooting outdoors on a cloudy day.  
: HALOGEN”  
4
RETURN  
M.W.B.  
M.W.B. Menu  
AUTO  
:
:
:
FINE  
CLOUD  
When using a video light or other similar type of  
lighting.  
HALOGEN  
MWB  
MWB”  
When shooting with the white balance already  
having been set on the subject (pg. 43).  
EXIT  
CLOSE MENU SCREEN  
5 Press the Select Dial. The Menu Screen reappears  
with the highlight bar on “RETURN”. Press the Select  
Dial again to close the Menu Screen.  
To Return To Automatic White Balance . . .  
.... select “AUTO” in step 4. Or set the Power Switch to  
“AUTO”.  
NOTE:  
White balance cannot be used when Sepia (pg. 33) is  
activated.  
EN43  
Manual White Balance Operation  
White paper  
If the camera is operating in PRO. mode, perform a  
Manual White Balance when shooting under various types  
of lighting.  
SELECT OPERATION SYSTEM AND  
1 MODE  
Follow steps 1 through 4 of the white balance  
adjustment (pg. 42), and select “MWB”.  
SET MANUAL WHITE BALANCE  
2 Hold a sheet of plain white paper in front of the  
subject. Adjust zoom or position yourself so that the  
white paper fills the screen.  
System Select Switch  
ENTER SETTING  
3 Press the Select Dial until “MWB” begins blinking.  
When the setting is completed, “MWB” stops  
blinking, and the Menu Screen reappears with the  
highlight bar on “RETURN”.  
CLOSE MENU SCREEN  
4 Press the Select Dial again to close the Menu Screen.  
Select Dial  
Display  
Power Switch  
Menu Screen  
To Change The Tint For Recording . . .  
.... in step 2, substitute colored paper for white. The white  
balance is adjusted based on the color, changing the  
tint. Red paper — deeper green; blue paper — orange;  
yellow paper — deeper purple.  
4
NEXT  
M.W.B.  
AUTO  
ON  
D . ZOOM  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T30  
PICTURE  
FINE  
FULL  
SNAPSHOT  
NOTES:  
In step 2, it may be difficult to focus on the white paper  
in some circumstances. In such a case, adjust focus  
manually (pg. 41).  
4
RETURN  
M.W.B.  
M.W.B. Menu  
A subject can be shot under various types of lighting  
conditions indoors (natural, flourescent, candlelight,  
etc.). Because the color temperature is different  
depending on the light source, the tint of the subject will  
differ depending on the white balance settings. Use this  
function for a more natural result.  
AUTO  
:
:
:
FINE  
CLOUD  
HALOGEN  
MWB  
EXIT  
Once you adjust white balance during Manual White  
Balance operation, the setting is retained even if the  
power is turned off or the battery removed.  
RECORDING Advanced Features (cont.)  
44  
EN  
Self-Timer  
You can set the delay between pressing the Recording  
Start/Stop button and the actual start of recording. If you  
secure the camcorder, you (or whoever is operating the  
camcorder) can enter the scene before recording starts.  
System  
Select Switch  
NOTE:  
Before performing the following steps, make sure that:  
The System Select Switch is set to “VIDEO” or “D.S.C.”  
according to your needs.  
The Power Switch is set to “PRO.”.  
The camcorder is in the Record-Standby mode.  
MENU Button  
ACCESS MENU SCREEN  
1 Press MENU.  
ACCESS “INT. TIME” MENU  
2 Rotate the Select Dial to move the highlight bar to  
“NEXT” in Menu Screen 1 and press it to display  
Menu Screen 2. Then, move the highlight bar to “INT.  
TIME” and press it.  
Select Dial  
Display  
Recording Start/Stop  
Button  
SET INTERVAL TIME  
3 Rotate the Select Dial to move the highlight bar to the  
Menu Screen 1  
4
NEXT  
desired time, then press it. The Menu Screen  
reappears with the highlight bar on “RETURN”.  
M.W.B.  
AUTO  
ON  
D . ZOOM  
TELE MACRO OFF  
DATE TIME  
TAPE LENGTH T30  
CLOSE MENU SCREEN  
PICTURE  
FINE  
FULL  
4 Press the Select Dial.  
SNAPSHOT  
4
RETURN  
START DELAYED RECORDING  
5 If you set the System Select Switch to “VIDEO” . . .  
.... press the Recording Start/Stop Button. When the  
selected time has elapsed, recording begins  
automatically.  
Menu Screen 2  
4BACK  
REC. TIME  
INT. TIME  
OFF  
OFF  
TALLY LAMP ON  
TITLE LANG. PORTUGUESE  
If you set the System Select Switch to “D.S.C.”. . .  
.... press SNAPSHOT. When the selected time has  
elapsed, a still image is shot automatically.  
JLIP ID NO  
06  
DEMO MODE OFF  
4
RETURN  
To Cancel Self-Timer . . .  
If you set the System Select Switch to “VIDEO” . . .  
.... before the recording begins, press the Recording Start/  
INT. TIME  
REC TIME  
OFF  
OFF  
1 4S  
1 2S  
1 S  
15S  
Stop Button to display “  
TIME” in the Menu Screen to “OFF”.  
”, then set “INT.  
30S  
1 MIN  
5 MIN  
5 S  
If you set the System Select Switch to “D.S.C.” . . .  
.... before shooting a still image, press SNAPSHOT, then  
set “INT.TIME” in the Menu Screen to “OFF”.  
EXIT  
EXIT  
INT. TIME Menu  
REC TIME Menu  
INT. TIME indicator  
REC TIME indicator  
15S  
1S  
INT. TIME and REC TIME indications on the normal  
screen  
EN45  
You can record sequentially at preset time spans.  
Leaving the camcorder aimed at a specific subject,  
you can record subtle changes over an extended  
period of time.  
Animation  
Time-Lapse  
You can give stationary scenes or objects an illusion  
of movement. This function allows you to shoot a  
series of pictures, each slightly different, of the same  
object for a brief period of time.  
NOTE:  
NOTE:  
Before performing the following steps, make sure  
that:  
Before performing the following steps, make sure  
that:  
The System Select Switch is set to “VIDEO”.  
The Power Switch is set to “PRO.”.  
The camcorder is in the Record-Standby mode.  
The recording mode is set to “SP”.  
The System Select Switch is set to “VIDEO”.  
The Power Switch is set to “PRO.”.  
The camcorder is in the Record-Standby mode.  
The recording mode is set to “SP”.  
ACCESS MENU SCREEN  
ACCESS MENU SCREEN  
1 Press MENU.  
1 Press MENU.  
SET RECORDING TIME  
SET INTERVAL BETWEEN  
2 Rotate the Select Dial to move the highlight bar 2 RECORDINGS  
to “NEXT” in Menu Screen 1 and press it to  
display Menu Screen 2. Then, move the  
Rotate the Select Dial to move the highlight bar  
to “NEXT” in Menu Screen 1 and press it to  
display Menu Screen 2. Then, move the  
highlight bar to “INT. TIME” and press it. The  
INT. TIME Menu appears. Rotate the Select Dial  
to move the highlight bar to the desired time,  
then press it. The Menu Screen reappears.  
highlight bar to “REC TIME” and press it. The  
REC TIME Menu appears. Rotate the Select Dial  
to move the highlight bar to the desired time,  
then press it. The Menu Screen reappears with  
the highlight bar on “RETURN”. Press the Select  
Dial again to close the Menu Screen.  
SET RECORDING TIME  
START RECORDING  
3 Rotate the Select Dial to move the highlight bar  
3 Press the Recording Start/Stop Button after  
to “REC TIME”, then press it. The REC TIME  
Menu appears. Rotate the Select Dial to move  
the highlight bar to the desired time, then press  
it. The Menu Screen reappears with the  
highlight bar on “RETURN”. Press the Select  
Dial again to close the Menu Screen.  
focusing on the subject. The recording stops  
automatically after the selected period of time.  
ASSEMBLE SERIES OF PICTURES  
4 Repeat step 3 for the desired number of  
pictures.  
START TIME-LAPSE RECORDING  
RELEASE ANIMATION MODE  
4 Press the Recording Start/Stop Button. Recording  
5 Set “REC TIME” in the Menu screen to “OFF”.  
and intervals alternate automatically.  
RELEASE TIME-LAPSE MODE  
NOTES:  
5 To release when “  
” is displayed, set  
For best results, make sure the camcorder is  
secured when shooting in Animation or Time-  
Lapse mode.  
“REC TIME” and “INT. TIME” in the Menu  
Screen to “OFF”. To release when  
” and “  
press the Recording Start/Stop Button to display  
”, then set “REC TIME” and “INT.  
TIME” in the Menu Screen to “OFF”.  
” are not displayed,  
Fade- or wipe-in/out cannot be performed during  
Animation or Time-Lapse shooting.  
Before performing other operations following  
Animation or Time-Lapse recording, make sure  
the Animation or Time-Lapse mode is deactivated.  
Self-Timer, Animation and Time-Lapse are  
canceled when the power is shut off or when the  
cassette is ejected.  
VIDEO PLAYBACK Basic Playback  
46  
EN  
LOAD A CASSETTE  
Power lamp  
1 First open the LCD monitor to an angle of over 60  
degrees. Slide EJECT to open the cassette holder, then  
insert the cassette with the label facing out. Press  
PUSH to ensure the holder is closed and locked.  
Power Switch  
SELECT OPERATION SYSTEM AND  
2 MODE  
Make sure the LCD monitor is fully open. Set the  
System Select Switch to “VIDEO”, and set the Power  
Switch to “PLAY”.  
System  
Select  
Switch  
PLAY BACK  
3 Press PLAY/PAUSE (  
4/6). The playback picture  
appears.  
STOP PLAYBACK  
4 Press STOP (5).  
EJECT Switch  
REW (2) Button  
Rewind or Fast-Forward the tape  
Press REW (2) to rewind, or FF (3) to fast-forward the  
FF (3) Button  
tape during Stop mode.  
PLAY/PAUSE (4/6)  
Button  
NOTES:  
The camcorder shuts off automatically after about  
5 minutes in Stop mode. To turn on again, set the Power  
Switch to “POWER OFF”, then to “PLAY”.  
STOP (5) Button  
When the Power Switch is set to “PLAY” and the LCD  
monitor is opened at an angle of 60 degrees or more, the  
LCD monitor switches on and the viewfinder switches  
off automatically to save power.  
LCD Monitor in Retracted Position  
The playback picture can also be viewed in the  
viewfinder (with the LCD monitor shut) or on a  
connected TV (pg. 50, 51). Camcorder operation is  
the same as described in this section.  
You can also view the playback picture on the LCD  
monitor with it flipped over and retracted.  
If a blank portion on the tape is played back, the screen  
may become black. This is not a malfunction.  
Battery pack remaining power indicator  
Tape counter  
Recording mode indicator  
Tape running  
SP  
:
:
M 1 23 45  
indicator  
4
3
:Playback  
:Fast-Forward/  
Forward Search  
:Rewind/Reverse  
Search  
2
6
:Still Playback  
LCD monitor/viewfinder  
indications  
VIDEO PLAYBACK Features  
EN47  
Adjust the brightness of the LCD monitor  
To brighten the image, turn the BRIGHT Dial towards “+”.  
Speaker  
To darken the image, turn the Dial towards “”.  
P.AE Button  
EFFECT Button  
NOTE:  
The Bright Level Indicator is displayed under the Date/  
Time Display when you play back images recorded in  
Wide Mode (pg. 37).  
Power Zoom Lever  
Speaker Volume Control  
You can adjust the speaker volume by pushing the Power  
Zoom Lever.  
ADJUST VOLUME  
1 If you want to turn up the volume . . .  
.... push the Power Zoom Lever towards “T”.  
If you want to turn down the volume . . .  
.... push the Power Zoom Lever towards “W”.  
BRIGHT Dial  
NOTE:  
The Speaker Volume Indicator is displayed under the Date/  
Time Display when you play back images recorded in  
Wide Mode (pg. 37).  
Set to “VIDEO”.  
Display  
Tracking  
This function can be used to eliminate noise bars that  
appear on-screen during playback. Initial setting is Auto  
Tracking. Manual Tracking is also available.  
ACTIVATE MANUAL TRACKING  
BRIGHT  
1 Press P.AE and EFFECT simultaneously. Then, press  
P.AE or EFFECT as many times as necessary until the  
noise bars disappear.  
BRIGHT  
To return to Auto Tracking, press P.AE and EFFECT  
simultaneously. “AT” blinks. When Auto Tracking  
finishes, the indication disappears.  
VOLUME  
NOTES:  
When noise bars appear during playback, the  
camcorder enters the Auto Tracking mode and “AT” is  
displayed.  
Manual Tracking may not work with tapes recorded on  
other VCRs or camcorders.  
VIDEO PLAYBACK Features (cont.)  
48  
EN  
Power Switch  
FEATURE: Still Playback  
PURPOSE:  
To pause during playback.  
OPERATION:  
1) Press PLAY/PAUSE (4/6) during playback.  
2) To resume normal playback, press PLAY/PAUSE  
(4/6) again.  
Set to “VIDEO”.  
NOTE:  
Noise bars appear and pictures may become  
monochrome during Still Playback. This is normal.  
FEATURE: Shuttle Search  
PURPOSE:  
To allow high-speed search in either direction.  
OPERATION:  
1) Press FF (3) to search forward or press REW (2  
to reverse during playback.  
)
REW (2) Button  
FF (3) Button  
2) To resume normal playback, press PLAY/PAUSE  
(4/6).  
NOTES:  
During playback, press and hold REW (2) or  
PLAY/PAUSE (4/6)  
FF (3). The search continues as long as you hold  
the button. Once you release it, normal playback  
resumes.  
Button  
STOP (5) Button  
Noise bars appear and pictures may become  
monochrome or darken during Shuttle Search. This  
is normal.  
COUNTER R/M Button  
FEATURE: Counter Memory Function  
PURPOSE:  
To make it easier to locate a specific tape segment.  
OPERATION:  
1) Press COUNTER R/M and hold for more than  
1 second. The counter resets to “0:00:00”.  
2) Press COUNTER R/M for less than 1 second. “M”  
appears.  
3) After recording or playback, press STOP (5), then  
REW (2). The tape automatically stops at or close  
to 0:00:00.  
4) Press PLAY/PAUSE (4/6) to start playback.  
NOTES:  
The counter memory functions in the Fast-Forward  
and Rewind modes.  
To disable the Counter Memory Function, press  
COUNTER R/M for less than 1 second so that “M”  
disappears.  
VIDEO PLAYBACK Using The Cassette Adapter  
Cassette Adapter (VHS Playpak)  
EN49  
Use this to play back a VHS-C video cassette recorded  
with this camcorder on a VHS VCR. It is fully compatible  
with any VHS video cassette recorder. The C-P7U adapter  
is battery powered and automatically performs tape  
loading and unloading.  
INSERT BATTERY  
1 Slide the battery cover up to remove it, and install  
one “AA(R6)” size battery as shown in the  
illustration at left, then reattach the cover.  
VCR  
INSERT CASSETTE IN ADAPTER  
2 Slide the latch to open the adapter compartment  
door, then insert the cassette and close the  
compartment door.  
Compartment door  
PLAY BACK ON CONNECTED VCR  
3 Load the cassette adapter into the VCR and play the  
tape back as you would any other.  
REMOVE CASSETTE FROM ADAPTER  
4 Slide the latch and the compartment door opens  
automatically. This may take around 10 seconds. Do  
not attempt to force the adapter open. Then, insert  
your finger in the hole on the underside of the  
adapter as shown in the illustration at left, and push  
up and remove the cassette.  
Sliding latch  
NOTES:  
Compact video cassette  
During tape loading and unloading, do not touch the  
reels for safety and tape protection.  
During special-effect playback (slow motion, still frame,  
etc.), the picture may vibrate or noise bars may appear  
on the screen.  
Reels  
To record on a VCR using a compact cassette and the  
adapter, cover the adapter’s recording safety hole with  
adhesive tape.  
Recording safety hole  
PLAYBACK Basic Connections And Tape Dubbing  
These are some basic types of connections. When making connections, refer also to your VCR and TV  
instruction manuals.  
50  
EN  
Basic Connections  
Use optional Video and Audio cables.  
TV  
To Video Output  
Video cable (optional)  
To VIDEO IN  
To AUDIO IN  
To TV or VCR  
Audio cable (optional)  
To Audio Output  
VCR  
Connector cover*  
Connection For Tape Dubbing  
Use optional Video and Audio cables.  
Power Switch  
TV  
PLAY/PAUSE (4/6)  
Button  
To Video  
Output  
To  
Video cable  
(optional)  
VIDEO IN  
VCR (Recording deck)  
Audio cable (optional)  
To Audio Output  
To AUDIO IN  
Connector cover*  
* When connecting the cables, open this cover.  
EN51  
Basic Connections  
Tape Dubbing  
CONFIRM POWER-OFF STATUS  
CONNECT EQUIPMENT  
1 Make sure the camcorder’s power is off.  
1 Following the illustration on pg. 50, connect the  
camcorder and the VCR.  
CONNECT CAMCORDER TO TV OR  
2 VCR  
PREPARE FOR DUBBING  
2 Set the camcorder’s Power Switch to “PLAY”,  
Pull out the connector cover and open it.  
turn on the VCR’s power, and insert the  
appropriate cassettes in the camcorder and the  
VCR.  
Connect as shown in the illustration (pg. 50).  
If using a VCR . . . go to step 3.  
If not . . . go to step 4.  
SELECT VCR MODE  
3 Engage the VCR’s AUX and Record-Pause  
CONNECT VCR OUTPUT TO TV  
3 INPUT  
modes.  
Refer to your VCR’s instruction manual.  
FIND EDIT-IN POINT  
4 Engage the camcorder’s Play mode to find a spot  
SUPPLY POWER  
4 Turn on the camcorder, the VCR and the TV.  
just before the edit-in point. Once it is reached,  
press PLAY/PAUSE (4/6) on the camcorder.  
SELECT MODE  
5 Set the VCR to its AUX input mode, and set the  
START EDITING  
5 Press PLAY/PAUSE (  
TV to its VIDEO mode.  
4/6) on the camcorder and  
engage the VCR’s Record mode.  
NOTES:  
It is recommended to use the AC Power Adapter/  
Charger as the power supply instead of the battery  
pack (pg. 11).  
STOP EDITING TEMPORARILY  
6 Engage the VCR’s Record-Pause mode and press  
PLAY/PAUSE (4/6) on the camcorder.  
To monitor the picture and sound from the  
camcorder without inserting a tape, set the  
camcorder’s Power Switch to “CAMERA” (“AUTO”  
or “PRO.”), then set your TV to the appropriate  
input mode.  
EDIT MORE SEGMENTS  
7 Repeat steps 4 through 6 for additional editing,  
then stop the VCR and camcorder when  
finished.  
Make sure you adjust the TV sound volume to its  
minimum level to avoid a sudden burst of sound  
when the camcorder is turned on.  
If you have a TV or speakers that are not specially  
shielded, do not place the speakers adjacent to the  
TV as interference will occur in the camcorder  
playback picture.  
NOTE:  
If you wish to dub still images recorded with the  
System Select Switch set to “D.S.C.”, play back the  
still images (pg. 52 – 56) instead of doing the  
above steps 4 through 6, engage the VCR's Record  
mode and record them onto a tape.  
D.S.C. PLAYBACK Basic Playback  
Still images shot using this camcoder are automatically  
numbered, then stored in numerical order in the built-in  
memory. You can view the still images stored in memory,  
one at a time, much like flipping through a photo album.  
52  
EN  
System  
Select Switch  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “D.S.C.”, and set the  
Power Switch to “PLAY”.  
•The power lamp lights.  
•The still image stored in memory is displayed.  
•When no still image is stored in memory, the screen  
becomes blue.  
Power lamp  
PLAY BACK  
2 Press FF (  
3/PAGE+) or REW (2/PAGE–) to select  
the still image you want to view.  
•Each time REW (2/PAGE–) is pressed, the page  
goes back, while each time FF (3/PAGE+) is  
pressed, the page goes next.  
Power Switch  
•Even if you shoot a new picture after playing back a  
still image with a low number, this will not  
overwrite the existing picture because new pictures  
are automatically stored after the still image most  
recently stored in memory.  
To move  
the page next  
Display  
NOTES:  
When the Power Switch is set to “PLAY” and the LCD  
monitor is opened at an angle of 60 degrees or more, the  
LCD monitor switches on and the viewfinder switches  
off automatically to save power.  
The playback picture can also be viewed in the  
viewfinder (with the LCD monitor shut) or on a  
connected TV (pg. 50). Camcorder operation is the  
same as described in this section.  
When viewing a playback picture on a connected TV, it  
may jitter slightly.  
You can also view the playback picture on the LCD  
monitor with it flipped over and retracted.  
To move  
the page back  
D.S.C. PLAYBACK Connection  
EN53  
Connection to a Windows® PC  
Image data stored in the camcorder’s built-in memory can  
be transferred to a Windows® PC and saved using the  
provided image transfer software, Picture Navigator. The  
image data transferred to a Windows® PC can also be  
further processed using Mr. Photo Gold, and the still image  
processed on the PC can be inserted onto a tape  
(pg. 63).  
Set to “D.S.C.”  
To assure safety, make sure all units are turned off before  
making any connection.  
To DIGITAL  
connector  
CONNECT TO PERSONAL  
1 COMPUTER  
Connect the camcorder’s DIGITAL connector to the  
COM Port (RS-232C) on a Windows® PC, using the  
provided PC connection cable.  
PC connection cable  
(provided)  
SELECT OPERATION SYSTEM AND  
2 MODE  
For Windows®:  
To COM Port  
(RS-232C)  
Set the System Select Switch to “D.S.C.”, then set the  
Power Switch to “PLAY”.  
•A still image stored in memory appears.  
When transferring still images to a computer, be  
sure that a still image is displayed on the screen.  
RUN IMAGE TRANSFER SOFTWARE  
®
3 Launch the provided software on your Windows PC.  
Transfer the still images stored in the camcorder’s  
memory to the Windows® PC. Refer to the software’s  
instruction manual on the provided CD-ROM for  
details.  
During transfer of the still image, the camcorder’s  
screen becomes blue and “  
” is dis-  
Display  
played. After transferring is finished, the screen  
displays the same still image as in step 2.  
END TRANSFERRING  
4 Close the software, then switch off the camcorder.  
PC MODE  
NOTES:  
Before transferring still images from your personal computer to the camcorder’s built-in memory, perform the  
camcorder’s Picture Mode Setting (pg. 24). The still images will be transferred from the personal  
computer in the selected Picture Mode.  
When transferring still images from your personal computer to the camcorder, make sure the number of  
images to be transferred is smaller than the camcorder's remaining number of shots available.  
Use the AC Power Adapter/Charger as the power supply instead of the battery pack.  
The still images stored in the camcorder’s memory are not automatically removed after being transferred to  
the PC. If you wish to remove those still images from the camcorder's memory, delete them (pg. 58, 59).  
Windows® are trademarks of Microsoft Corporation, registered in the U.S.A. and other countries.  
D.S.C. PLAYBACK Advanced Features  
54  
EN  
Using Menu For Detailed Adjustment  
This camcorder is equipped with an easy-to-use,  
on-screen menu system that simplifies many of the more  
detailed camcorder settings.  
System  
Select Switch  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “D.S.C.”, and set the  
Power Switch to “PLAY”.  
ACCESS MENU SCREEN  
2 Press MENU. The Menu Screen appears.  
MENU Button  
SELECT FUNCTION  
3 Rotate the Select Dial to place the highlight bar on  
the desired function.  
•If the setting you want cannot be found in the Menu  
Screen, place the highlight bar on “RETURN”, then  
press the Select Dial.  
Select Dial  
Power Switch  
Menu Screen  
MAKE SETTING  
4 Press the Select Dial. The setting menu of the selected  
Display  
function appears. The setting procedure depends on  
the function you select.  
MENU  
INDEX  
If you select “SLIDE SHOW 1” or “SLIDE SHOW 2” . . .  
SLIDE SHOW 1  
SLIDE SHOW 2  
PROTECT  
.... a slide-show will start (pg. 55).  
DELETE  
If you select any other functions . . .  
.... see respective pages (INDEX: pg. 56,  
PROTECT: pg. 57, DELETE: pg. 58, 59)  
and do each procedure from step 4.  
4RETURN  
EXIT <PROTECT>  
Setting Menu  
(ex. PROTECT)  
01  
02  
03  
04  
05  
MENU  
INDEX  
SLIDE SHOW 1  
SLIDE SHOW 2  
PROTECT  
DELETE  
4RETURN  
Normal Screen  
EN55  
Menu Screen Explanations  
Mode  
Effect  
INDEX  
All still images stored in memory can be displayed six at a time. This mode is a  
convenient way to look for the still image you want to view and to check the still  
images you shot beforehand (pg. 56).  
SLIDE SHOW 1  
After doing steps 1 through 4 on pg. 54, you can run through all the still images  
stored in memory automatically in numerical order. Each still image is displayed.  
This mode is like a regular slide-show. If you wish to stop the slide-show, press the  
Select Dial twice.  
SLIDE SHOW 2  
After doing steps 1 through 4 on pg. 54, you can run through all the still images  
stored in memory automatically in numerical order. The still image wipes in over  
the last one from the bottom of the screen to the top. If you wish to stop the slide-  
show, press the Select Dial twice.  
PROTECT  
DELETE  
Lets you protect selected still images from accidental erasure. Select a still image for  
which you want to perform “Protect” to put a padlock mark next to it. A still image  
with a padlock mark cannot be deleted. When selecting a still image to protect, you  
can check six still images stored in memory at a time (pg. 57).  
Allows you to delete some still images already stored in memory (pg. 58).  
CAUTION:  
While “ENTER” is selected on the Delete Execute Menu and it is blinking, switching  
off the camcorder or removing the power supply unit (battery pack or AC Power  
Adapter/Charger) may cause the camcorder’s built-in memory to become corrupt.  
Never remove the power supply unit at this stage.  
SELECT  
Allows you to check 6 still images stored in memory at a time, to select  
the still images you want to delete.  
ALL  
Allows you to delete all the still images at once except protected  
images.  
D.S.C. PLAYBACK Advanced Features (cont.)  
56  
EN  
Index  
You can view all still images stored in memory six at a  
time. Use this mode when looking for a still image you  
want to view and when checking the still images you shot  
beforehand.  
System  
Select Switch  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “D.S.C.”, and set the  
Power Switch to “PLAY”.  
ACCESS MENU SCREEN  
MENU Button  
2 Press MENU. The Menu Screen appears.  
ACCESS “INDEX” MENU  
3 Rotate the Select Dial to move the highlight bar to  
“INDEX” and press it. The “INDEX” Menu appears.  
VIEW INDEX IMAGES  
4 Rotate the Select Dial to move the frame to the  
Select Dial  
Power Switch  
desired still image, then press it. The one you selected  
is displayed on the whole screen, then the screen  
enters normal playback.  
Display  
MENU  
•On the INDEX Menu, 6 still images are displayed at  
a time. When viewing the still images that follow  
the 6th one, rotate the Select Dial to move the  
frame from Index No. 1 to No. 6, and then rotate it  
further downward. The frame is placed on the 7th  
still image automatically. Images after the 7th one  
can also be accessed in the same way.  
Menu Screen  
INDEX  
SLIDE SHOW 1  
SLIDE SHOW 2  
PROTECT  
DELETE  
4RETURN  
•If the desired still image cannot be found, place the  
highlight bar on “EXIT”, then press the Select Dial  
twice to exit the Menu.  
EXIT  
01  
<INDEX>  
02  
INDEX Menu  
03  
06  
NOTES:  
04  
When moving the frame from the 7th still image back to  
the 6th, rotate the Select Dial upward to place the  
highlight bar on “EXIT”, then rotate it further upward.  
The frame is moved to the 6th still image. Perform the  
same procedure for the 13th image.  
On the INDEX Menu, a star mark is displayed next to a  
still image you shot in the FINE mode.  
Playback Screen  
EN57  
Protect  
This mode helps prevent accidental erasure of images. Put  
a padlock mark next to the desired still image, and that still  
image cannot be deleted.  
System  
Select Switch  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “D.S.C.”, and set the  
Power Switch to “PLAY”.  
ACCESS MENU SCREEN  
2 Press MENU. The Menu Screen appears.  
MENU Button  
ACCESS “PROTECT” MENU  
3 Rotate the Select Dial to move the highlight bar to  
“PROTECT”, and press it. The PROTECT Menu  
appears.  
If you do not want to perform “Protect” for any still  
image, go to step 5.  
Select Dial  
Power Switch  
Menu Screen  
SET PROTECT  
4 Rotate the Select Dial to move the frame to the  
Display  
desired still image, then press it. The padlock mark  
appears above the selected image.  
MENU  
INDEX  
SLIDE SHOW 1  
SLIDE SHOW 2  
PROTECT  
On the PROTECT Menu, all still images are  
displayed six at a time. To perform “Protect” for the  
still images that come after the 6th one, rotate the  
Select Dial to move the frame from Index No. 1 to  
No. 6, then rotate it further downward. The frame is  
placed automatically on the 7th still image. Images  
after the 7th one can also be accessed in the same  
way.  
DELETE  
4RETURN  
EXIT <PROTECT>  
PROTECT Menu  
01  
03  
To complete “Protect”, go to step 5.  
CLOSE MENU SCREEN  
04  
05  
06  
5 Rotate the Select Dial upward to place the highlight  
bar on “EXIT”, then press it twice.  
To remove “Protect” . . .  
EXIT <PROTECT>  
.... perform steps 1 through 3, rotate the Select Dial to  
move the frame to the desired still image with the  
padlock mark, then press it. The padlock mark located  
above the still image disappears and the image is no  
longer protected. When finished removing protection,  
perform step 5.  
01  
03  
04  
05  
06  
A padlock mark  
appears.  
NOTES:  
To move the frame from Index No. 7 to 6, place the  
highlight bar on “EXIT” by rotating the Select Dial  
upward. Rotate the Select Dial further upward. The  
frame is moved to the 6th still image automatically.  
Perform the same procedure for still images that follow  
the 13th one.  
On the PROTECT Menu, a star mark is displayed next to  
a still image you shot in the FINE mode.  
D.S.C. PLAYBACK Advanced Features (cont.)  
58  
EN  
Delete  
When the memory in which still images are stored  
becomes full, the number of remaining shots available  
reaches “0” (blinking). In this situation it becomes  
impossible to take your next shot. Delete some still images  
already stored in memory to make room for new shots.  
System  
Select Switch  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “D.S.C.”, and set the  
Power Switch to “PLAY”.  
MENU Button  
ACCESS MENU SCREEN  
2 Press MENU. The Menu Screen appears.  
ACCESS “DELETE” MENU  
3 Rotate the Select Dial to move the highlight bar to  
“DELETE”, and press it. The DELETE Menu appears.  
SELECT DELETE MODE  
Select Dial  
Power Switch  
4 Rotate the Select Dial to move the highlight bar to  
“SELECT” or “ALL”, then press it.  
To select a still image by checking the still images  
stored in memory . . .  
Display  
MENU  
Menu Screen  
INDEX  
.... select “SELECT”, then go to step 5.  
To delete all the still images stored in memory at  
once without checking them . . .  
SLIDE SHOW 1  
SLIDE SHOW 2  
PROTECT  
DELETE  
.... select “ALL”, then go to step 6.  
To quit the Delete Mode . . .  
.... rotate the Select Dial to place the highlight bar  
on “EXIT”, then press it twice.  
4RETURN  
DELETE  
DELETE Menu  
SELECT ON DELETE SELECT MENU  
SELECT  
ALL  
5 Rotate the Select Dial to move the frame to the  
desired still image, then press it. “ ” appears above  
the selected still image. When you have finished  
selecting all the desired still images, rotate the Select  
Dial upward to place the highlight bar on “NEXT”,  
then press the Select Dial.  
In case of “ALL”  
EXIT  
NEXT <DELETE>  
•On the Delete Select Menu, the still images are  
displayed six at a time. To delete the still images  
that follow the 6th one, rotate the Select Dial to  
move the frame from No. 1 to No. 6, then rotate it  
further downward. The frame is moved to the 7th  
still image automatically. Perform the same  
In case of  
“SELECT”  
01  
02  
06  
04  
05  
procedure for still images that follow the 7th one.  
Delete Select Menu  
DELETE  
CANCEL  
ENTER  
Delete Execute Menu  
Menu Screen  
EN59  
In case of “SELECT”  
ACCESS DELETE EXECUTE MENU  
6 Rotate the Select Dial to move the highlight bar to  
NEXT <DELETE>  
“CANCEL” or “ENTER”, then press it.  
01  
02  
06  
CANCEL” does not delete the selected still images  
and the screen returns to the Menu Screen.  
ENTER” deletes the selected still images. While  
“ENTER” blinks, they are in the process of being  
deleted from memory. After deleting is finished, the  
screen returns to the Menu Screen.  
04  
05  
CLOSE MENU SCREEN  
7 Press the Select Dial again to exit the Menu Screen.  
CAUTION:  
If you check the remaining still images on  
INDEX Menu after deleting...  
While “ENTER” is selected on the Delete  
Execute Menu and it is blinking, switching off  
the camcorder or removing the power supply  
unit (battery pack or AC Power Adapter/Charger)  
may cause the camcorder’s built-in memory to  
become corrupt. Never remove the power  
supply unit at this stage.  
EXIT  
01  
<INDEX>  
02  
03  
06  
NOTES:  
04  
05  
Before deleting some still images stored in memory,  
perform “Protect” for the necessary ones (pg. 57) or  
save them on a PC so that you do not lose them  
accidentally (pg. 53).  
Even if “ALL” is selected on the DELETE Menu, it is not  
possible to delete a still image with a padlock mark.  
“ALL” only deletes all still images that are not protected.  
After images are deleted from memory, the remaining  
images are automatically moved up to fill in any gaps in  
the numerical sequence. The Index No. for images  
protected (with the padlock mark) may therefore change.  
When selecting the desired still image in step 5, to move  
the frame from No. 7 to 6, place the highlight bar on  
“EXIT” by rotating the Select Dial upward. Rotate it  
further upward to move the frame to No. 6. Perform the  
same procedure for still images that follow the 13th one.  
On the Delete Select Menu, a star mark is displayed next  
to a still image you shot in the FINE mode.  
If the remaining number of shots is not 30 in the FINE  
mode or 60 in the STANDARD mode when “ALL” is  
selected on the DELETE Menu, initialize the camcorder’s  
memory (pg. 68).  
USING THE REMOTE CONTROL UNIT  
The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic  
operations (Playback, Stop, Pause, Fast-Forward and Rewind) of your VCR.  
60  
EN  
Installing The Battery  
1
The remote control uses one lithium battery  
(CR2025).  
7
8
9
0
!
@
PULL OUT BATTERY HOLDER  
2
1 Pull out the battery holder by inserting a pointed  
instrument into the slot.  
2
3
4
5
6
INSERT BATTERY IN HOLDER  
3
2 Insert the battery in the holder, and be sure to  
1
have the “+” mark visible.  
Slot  
RE-INSERT HOLDER  
3 Slide the holder back in until you hear a click.  
•Read the caution concerning lithium batteries  
(pg. 2).  
RM-V705U  
(provided)  
Functions  
Buttons  
With the camcorder’s Power Switch set  
to “CAMERA”, “AUTO” or “PRO.”  
With the camcorder’s Power Switch  
set to “PLAY”.  
1 Infrared beam  
Transmits the beam signal.  
transmitting window  
2 ZOOM (T/W) Buttons  
3 PLAY Button  
Zoom in/out (pg. 28)  
Playback start (pg. 46)  
Stop (pg. 46)  
4 STOP Button  
5 REW Button  
Retake (rewind)/Quick Review  
(pg. 29)  
Rewind, Reverse Shuttle Search  
(pg. 46, 48)  
6 INSERT Button  
7 START/STOP Button  
8 INT. TIME Button  
9 REC TIME Button  
0 PAUSE Button  
! FF Button  
Insert Editing (pg. 62, 63)  
Functions the same as the Recording Start/Stop Button on the camcorder.  
Self-Timer/Time-Lapse (pg. 61)  
Animation/Time-Lapse (pg. 61)  
Pause (pg. 48)  
Retake (forward) (pg. 29)  
Fast-Forward, Forward Shuttle Search  
(pg. 46, 48)  
@ A.DUB Button  
Audio dubbing (pg. 64)  
EN61  
FEATURE: Self-Timer, Animation and  
Time-Lapse  
Transmitted beam  
effective area  
PURPOSE:  
The remote control lets you set/release Interval Timer  
and Rec Time functions without using the Menu  
Screen.  
OPERATION:  
Remote sensor  
Self-Timer  
1) Set  
Instead of performing steps 1 through 4 on pg. 44  
(“Self-Timer”), press INT. TIME on the remote  
control. Each time INT. TIME is pressed, the Interval  
Timer indicator appears, changing in the following  
order: 15S, 30S, 1MIN, 5MIN and No indication  
(off).  
When using the remote control, be sure to point it at  
the remote sensor. The above illustration shows the  
approximate transmitted beam effective area for  
indoor use.  
The transmitted beam may not be effective or may  
cause incorrect operation outdoors or when the  
remote sensor is directly exposed to sunlight or  
powerful lighting.  
2) Release  
Instead of setting “INT. TIME” to “OFF” in the Menu,  
press INT. TIME on the remote control until the  
Interval Timer indicator disappears.  
Animation  
Interval timer indicator  
1) Set  
Instead of performing steps 1 and 2 on pg. 45  
(“Animation”), press REC TIME on the remote  
control. Each time REC TIME is pressed, the Rec  
Time indicator appears, changing in the following  
order: 1/4S, 1/2S, 1S, 5S and No indication (off).  
2) Release  
1MIN  
2S  
1
Instead of using the Menu in step 5 on pg. 45, press  
REC TIME on the remote control until the Rec Time  
indicator disappears.  
Rec time indicator  
Time-Lapse  
1) Set  
Instead of performing steps 1 through 3 on pg. 45  
(“Time-Lapse”), press INT. TIME and REC TIME on  
the remote control. Each time INT. TIME is pressed,  
the Interval Timer indicator appears, changing in the  
following order: 15S, 30S, 1MIN, 5MIN and No  
indication (off). Each time REC TIME is pressed, the  
Rec Time indicator appears, changing in the  
following order: 1/4S, 1/2S, 1S, 5S and No indication  
(off).  
Remote sensor  
2) Release  
Instead of using the Menu in step 5 on pg. 45, press  
INT. TIME and REC TIME on the remote control until  
the indicators disappear.  
NOTE:  
Also refer to pgs. 44 and 45.  
START/STOP  
INT. TIME  
REC. TIME  
RM-V705U  
(provided)  
USING THE REMOTE CONTROL UNIT (cont.)  
62  
EN  
Insert Editing (VIDEO)  
Power Switch  
You can record a new scene onto a previously recorded  
tape, replacing a section of the original recording with  
minimal picture distortion at the in- and out-points. The  
original audio remains unchanged.  
System Select Switch  
NOTE:  
Use the RM-V705U remote control unit to perform this  
procedure.  
SELECT OPERATION SYSTEM AND  
1 MODE  
Set the System Select Switch to “VIDEO”, and set the  
Power Switch to “PLAY”.  
REW (2) Button  
FIND EDIT-OUT POINT  
2 Play back the tape, locate the point and press PAUSE  
FF (3) Button  
PLAY/PAUSE (4/6) Button  
on the camcorder or the remote control.  
RESET COUNTER  
STOP (5) Button  
3 Press and hold COUNTER R/M for more than  
1 second to reset the tape counter, then press again  
for less than 1 second so that “M” appears.  
COUNTER R/M Button  
FIND EDIT-IN POINT  
Display  
4 Press REW to go a little beyond the beginning of the  
Insert editing  
indicator  
scene you want to replace, press PLAY to view the  
recorded tape, and press PAUSE exactly at the  
point where the new scene should start.  
:
:
Tape Counter  
Remote sensor  
M 0 12 34  
ENGAGE INSERT EDITING MODE  
5 Press and hold INSERT, and without releasing  
INSERT, press and release PAUSE. The Insert Editing  
standby mode is engaged. The Insert Editing Indicator  
is displayed on the top left corner of the LCD monitor  
or viewfinder. When the scene the camcorder is  
aimed at appears on the screen, go to the next step.  
BEGIN INSERT EDITING  
6 Press START/STOP. When the counter reaches  
“0:00:00”, editing stops automatically and the  
camcorder enters the Insert-Pause mode.  
END INSERT EDITING  
7 Press STOP.  
NOTES:  
During Insert Editing, the original audio will be heard  
from the speaker.  
START/STOP  
After step 5, Retake (pg. 29) can be performed.  
The tape may stop slightly before or after the designated  
end point, and noise bars may appear. Neither indicates  
a defect in the unit.  
Only the video signal is recorded in the Insert Editing  
mode.  
PLAY  
STOP  
PAUSE  
REW  
INSERT  
RM-V705U  
(provided)  
EN63  
Insert Editing (Insert A Still Image From  
Power Switch  
The Built-in Memory Onto A Tape)  
You can insert a still image stored in the camcorder's built-  
in memory into a previously recorded tape, replacing a  
section of the original recording with minimal picture  
distortion at the in- and out-points. The original audio  
remains unchanged.  
System Select Switch  
Perform steps 1 through 5 in Insert Editing (VIDEO)  
(pg. 62) before the following procedure.  
NOTE:  
Use the RM-V705U remote control unit to perform this  
procedure.  
SELECT STILL IMAGE  
REW (2/PAGE–) Button  
1 First set the System Select Switch to “D.S.C.”. Press  
FF (3/PAGE+) Button  
PLAY/PAUSE (4/6) Button  
REW (2/PAGE–) or FF (3/PAGE+) to select the  
still image you wish to insert.  
BEGIN INSERT EDITING  
STOP (5) Button  
2 Press START/STOP. When the counter reaches  
“0:00:00”, editing stops automatically and the  
camcorder enters the Insert-Pause mode.  
COUNTER R/M Button  
To insert still images in sequential order onto the  
tape . . .  
Display  
... press REW (2/PAGE–) or FF (3/PAGE+) to  
move the page forward.  
Insert editing  
indicator  
To insert still images at random onto the tape . . .  
... first record the still image you selected in step 1  
onto the tape, then press START/STOP to engage  
the Insert-Pause mode. To select another still  
:
:
M 0 12 34  
Tape counter  
image, press REW (2/PAGE–) or FF (3  
/
PAGE+) again, then press START/STOP. Insert-  
Editing begins.  
Remote sensor  
END INSERT EDITING  
3 PressSTOP.  
NOTES:  
The tape may stop slightly before or after the designated  
end point, and noise bars may appear. Neither indicates  
a defect in the unit.  
Only video signal is recorded in the Insert Editing mode.  
START/STOP  
PLAY  
STOP  
PAUSE  
REW  
INSERT  
RM-V705U  
(provided)  
USING THE REMOTE CONTROL UNIT (cont.)  
64  
EN  
Display  
Audio Dubbing  
e
4
Audio dubbing  
indicator  
You can record a new soundtrack on a prerecorded tape  
:
:
M 0 05 20  
(normal audio only).  
Perform steps 1, 2 and 3 of the Insert Editing procedure  
(pg. 62) before continuing.  
The sound comes from the built-in microphone.  
FIND EDIT-IN POINT  
1 Press REW to go a little beyond the beginning of the  
scene onto which you want to dub the new audio,  
press PLAY to view the recorded tape, then press  
PAUSE at exactly the point where dubbing should  
start.  
Remote sensor  
Microphone  
ENGAGE AUDIO DUB-STANDBY MODE  
2 Press and hold A. DUB, and without releasing  
A. DUB, press and release PAUSE. The Audio Dub  
standby mode is engaged. The Audio Dubbing  
Indicator is displayed on the top right corner of the  
LCD monitor or viewfinder.  
BEGIN AUDIO DUBBING  
3 Press PLAY. When the counter reaches “0:00:00”,  
Audio Dubbing stops automatically and the  
camcorder enters the Audio Dub-Standby mode.  
END AUDIO DUBBING  
4 PressSTOP.  
Set to “VIDEO”  
PLAY  
PAUSE  
STOP  
REW  
NOTES:  
Do not press FF or REW during Audio Dub-Standby, or  
the edit points will not be accurate.  
If the microphone is too close to the TV, or if the TV’s  
volume is too high, whistling or howling may occur.  
A. DUB  
RM-V705U  
(provided)  
NOTES (for Insert Editing and  
Audio Dubbing):  
Insert Editing and Audio Dubbing may not work  
correctly if the tape contains blank segments, or if the  
recording speed was changed during the original  
recording.  
To edit/dub onto a tape, make sure the Erase Protection  
tab is in the position that allows recording. If not, slide  
the tab. Some cassettes have removable tabs. If the tab  
has been removed, cover the hole with adhesive tape.  
Do not press STOP during Insert Editing or Audio  
Dubbing, or the edit points will not be accurate.  
During Insert Editing and Audio Dubbing, when Insert-  
Pause or Audio Dub-Standby is engaged, the counter  
may go slightly past “0:00:00”. Recording, however,  
stops at exactly 0:00:00.  
USER MAINTENANCE  
EN65  
LENS COVER Open/Close Ring  
After Use  
Set the Power Switch to “POWER OFF” to turn off  
1 the camcorder.  
Open the LCD monitor to an angle of over 60  
2 degrees. Slide EJECT to open the cassette holder, then  
remove the cassette.  
Close and lock the cassette holder by pressing PUSH.  
3
4
5
Close and lock the LCD monitor.  
BATTERY RELEASE  
Set to “POWER OFF”.  
Slide BATTERY RELEASE to remove the battery pack.  
Turn the LENS COVER Open/Close Ring to close  
6 the lens cover.  
Cleaning The Camcorder  
CLEAN EXTERIOR  
1 Wipe gently with a soft cloth.  
Remove.  
Put cloth in diluted mild soap and wring it well to  
wipe off heavy dirt, then wipe again with a dry  
cloth.  
PUSH  
EJECT  
CLEAN LCD MONITOR  
2 Open the LCD monitor and wipe it gently with a soft  
cloth. Be careful not to damage the monitor. Close  
the LCD monitor.  
CLEAN LENS  
3 Blow it with a blower brush, then wipe it gently with  
lens cleaning paper.  
REMOVE EYEPIECE  
4 Turn the eyepiece counterclockwise and pull it out.  
CLEAN VIEWFINDER  
5 Remove dust using a blower brush.  
RE-ATTACH EYEPIECE  
6 Re-attach the eyepiece and turn it clockwise.  
NOTES:  
Avoid using strong cleaning agents such as benzine or alcohol.  
Cleaning should be done only after the battery pack has been removed or other power units have been  
disconnected.  
Mold may form if the lens is left dirty.  
When using a cleaner or chemically treated cloth, refer to the cautions that came with it.  
When removing the eyepiece, be sure to hold the viewfinder securely.  
TROUBLESHOOTING  
66  
EN  
If, after following the steps in the chart below, the problem still exists, please consult your JVC dealer.  
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might  
prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Power  
Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and proceed as usual from the beginning.  
SYMPTOM  
POSSIBLE CAUSE(S)  
POWER  
No power is supplied.  
The battery pack has not been attached correctly (pg. 10).  
The battery pack is not charged (pg. 10).  
The power supply has not been correctly connected (  
pg. 11).  
The power suddenly goes off and  
does not come back on by itself.  
The battery pack has completely discharged.  
Remove the cassette and disconnect the power source, then  
after a few minutes, try turning the power back on. If it still  
doesn’t come on, consult your nearest JVC dealer.  
OTHER  
Some functions are not available.  
The Power Switch is set to “AUTO”.  
Certain combinations of modes or effects are not possible to use.  
Press DISPLAY for longer than 1 second to make the  
indications appear (pg. 19).  
During recording, the indications do  
not appear.  
Vertical white lines appear when  
shooting a very bright object.  
This sometimes occurs when the contrast between the back-  
ground and the object is great. It is not a defect of the camcorder.  
Bright, crystal-shaped spots appear in  
the LCD monitor and the viewfinder.  
Sunlight is directly entering the lens. This is not a defect of  
the camcorder.  
The rear of the LCD monitor is hot.  
The light used to illuminate the LCD monitor causes it to be  
hot. Close the LCD monitor to turn it off or set the power  
switch to “OFF”, and let the unit cool down.  
Colored bright spots appear all over  
the LCD monitor or the viewfinder.  
The LCD monitor and the viewfinder are made with high-precision  
technology. However, black spots or bright spots of light (red, green  
or blue) may appear constantly on the LCD monitor or in the  
viewfinder. These spots are not recorded on the tape. This is not  
due to any defect of the unit. (Effective dots: more than 99.99 %.)  
The indicators and the picture color  
on the LCD monitor are not clear.  
This may occur when the surface or the edge of the LCD  
monitor is pressed.  
The LCD monitor, the viewfinder and  
the lens have become dirty (ex.  
fingerprints).  
Wipe them gently with soft cloth. Gently wipe the LCD  
monitor in a semicircle because wiping strongly spreads the  
stain and it won’t come out easily.  
An error number (i.e. E03) appears.  
Turn the camcorder’s power off, then disconnect the power  
source. After a few minutes, try turning the power on again. If  
the error number still appears, consult your nearest JVC dealer.  
The image is out of focus.  
The diopter needs to be adjusted (pg. 16).  
The scene being shot is adversely affecting the operation of  
Auto Focus (pg. 40).  
The Lens Cover Warning indicator may blink when the  
camcorder is used in dark areas, regardless of the position  
of the Lens Cover.  
Even though the Lens Cover is open,  
the Lens Cover Warning indicator  
blinks.  
TROUBLESHOOTING (cont.)  
When the System Select Switch is set to “VIDEO”:  
EN67  
SYMPTOM  
POSSIBLE CAUSE(S)  
RECORDING  
Recording cannot be performed.  
Make sure the Erase Protection tab is in the position that  
allows recording. If not, slide the tab. Some cassettes have  
removable tabs. If the tab has been removed, cover the  
hole with adhesive tape (pg. 15).  
If the System Select Switch is set to “D.S.C.”, it is not  
possible to record onto the tape. Change the Switch  
position to “VIDEO” (pg. 18).  
Recording does not start.  
The camcorder Power Switch has not been set to  
“CAMERA” (“AUTO“ or “PRO.“) (pg. 18).  
PLAYBACK  
The tape is running, but there is no  
playback picture.  
The TV has not been set to its VIDEO mode or channel.  
If A/V connection is used, the TV’s VIDEO/TV Switch has  
not been set to VIDEO.  
Playback cannot be performed.  
If the System Select Switch is set to “D.S.C.”, it is not  
possible to play back a tape. Change the Switch position to  
“VIDEO” (pg. 46).  
Playback picture is blurred or  
interrupted.  
The video heads are dirty or worn out. Consult your nearest  
JVC dealer for head cleaning or replacement.  
The counter indication is blurred  
during Still playback.  
This is normal.  
TAPE TRANSPORT  
The tape stops during fast-forward or  
rewind.  
The Counter Memory Function has been activated  
(pg. 48).  
Rewinding or fast-forwarding cannot  
be performed.  
The tape is already fully wound on one reel or the other.  
OTHER  
The picture is blurred in the Quick  
Review or Retake mode.  
This is normal while recording in the EP mode. Some noise  
may be present while recording in the SP mode  
(pg. 14).  
The date and time displays  
disappear.  
If you remove the power source from the camcorder while  
the power is on, all settings and selections are erased. Make  
sure to turn the camcorder’s power off before disconnecting  
the power source.  
The wrong date and time are  
displayed/recorded.  
If you have not performed Date/Time Setting (pg. 13),  
the date and time are not displayed/recorded correctly. Be  
sure that Date/Time setting is carried out.  
The tape will not eject.  
The battery pack is running low.  
If the LCD monitor is not open over 60 degrees, EJECT  
switch does not function.  
68  
EN  
When the System Select Switch is set to “D.S.C.”:  
SYMPTOM  
POSSIBLE CAUSE(S)  
SHOOTING  
Although the SNAPSHOT Button is  
pressed, a still image is not stored in  
the built-in memory.  
When the number of remaining shots available reaches “0”  
(blinking), it becomes impossible to take your next shot.  
Perform “DELETE” function to remove some still images  
already stored in memory (pg. 58).  
Self-Timer Shooting is not available.  
Pressing the Recording Start/Stop Button does not start  
recording in the Self-Timer Shooting procedure. Press the  
SNAPSHOT Button (pg. 44).  
It is not possible to shoot in  
sucession.  
A still image is in the process of being stored in memory for  
approx. 2 seconds after the SNAPSHOT Button is pressed.  
During that time, it is impossible to take another shot. When  
the still image disappears and the scene you are currently  
aimed at appears on the screen, take another shot (pg. 22).  
PLAYBACK  
Although “ALL” is selected in the  
DELETE Menu Screen, all still images  
cannot be deleted.  
The “Protect” function is in effect for some still images. If  
they are not necessary, cancel the “Protect” function, then  
try deleting all still images again (pg. 57).  
OTHER  
Date/Time Insert is not performed  
It is not possible to display the date/time on a still image.  
It is not possible to display the Instant Titles on a still image.  
It is not possible to set “REC TIME” in the Menu Screen.  
while shooting a still image.  
Instant Titles are not displayed while  
shooting a still image.  
Some settings cannot be changed in  
the Menu Screen.  
Since the camcorder is a microcomputer-controlled device, external noise and interference (from a TV, a  
radio, etc.) might prevent it from functioning properly. For example, when a still image you shot is stored  
in the camcorder's built-in memory, the above may cause the following: Although the remaining number  
of shots indicator shows that shooting is possible, a still image cannot be stored in memory after shooting.  
In such a case, initialize the memory by following steps 1 through 3 below. Please note that initialization  
deletes all the still images (including ones for which you performed the “Protect” function) stored in the  
camcorder’s memory. If you wish to keep any of the still images that are stored in memory, before  
initialization first transfer them to a PC and save them. If image data is corrupt, transfer is impossible.  
1. Set the System Select Switch to “D.S.C.”, then set the Power Switch to  
“PLAY”.  
FORMAT  
CANCEL  
ENTER  
2. Press the SP/EP Recording Mode Button for more than 2 seconds. The  
FORMAT Menu Screen appears.  
3. Rotate the Select Dial to move the highlight bar to “CANCEL” or  
“ENTER”, then press it.  
CANCEL” does not initialize the memory.  
ENTER” initializes the memory. During initialization, “ENTER” blinks.  
When initialization is complete, the screen becomes blue back.  
FORMAT Menu  
CAUTION:  
While “ENTER” is selected and it is blinking, switching off the camcorder or removing the power supply  
unit (battery pack or AC Power Adapter/Charger) may cause the camcorder’s built-in memory to become  
corrupt. Never remove the power supply unit at this stage.  
INDEX Controls, Connectors And Indicators  
EN69  
o
u 2  
1
p
w
W
E
R
Q
e r  
7
9
0
8
U
!
#
@
$
&
%
^
q
3
4 5 6  
T
Y
I
O
P
t y * ( i )  
70  
EN  
Controls  
Connectors  
1 Diopter Adjustment Control ................. pg. 16  
w DC IN Jack .......................................... pg. 11  
2 Lens Cover Open/Close Ring................ pg. 18  
The connectors e to t are located beneath the  
cover.  
3 Video Light Switch  
[LIGHT OFF/AUTO/ON]...................... pg. 30  
e Video Output Connector ...................... pg. 50  
4 Snapshot Button [SNAPSHOT] ....... pg. 22, 26  
r Audio Output Connector ..................... pg. 50  
5 •Power Zoom Lever [T/W] .................. pg. 28  
t J Terminal [JLIP (Joint Level Interface Protocol)  
•Speaker Volume Control [VOL.] ........ pg. 47  
Connector]  
It is used to connect the camcorder to a device  
such as a personal computer.  
For further details consult your nearest JVC  
dealer.  
JLIP-controlled editing from camcorder to VCR  
is not possible if the VCR is not equipped with a  
J terminal.  
6 Picture Stabilizer Button  
[P.STABILIZER] ..................................... pg. 29  
7 Program AE Button [P.AE]..................... pg. 32  
8 Fade/Wipe Button [EFFECT] ................. pg. 31  
9 System Select Switch  
[D.S.C./VIDEO] ................ pg. 18, 22, 46, 52  
y Digital Connector ............................... pg. 53  
0 Rewind Button  
[
2, REW/PAGE–] ...................... pg. 46, 52  
Indicators  
Retake Rewind Button [RETAKE R] ..... pg. 29  
Quick Review Button [ R] ............. pg. 29  
u Tally Lamp ........................................... pg. 18  
i Power Lamp ........................................ pg. 18  
! Fast-Forward Button  
[3, FF/PAGE+] .......................... pg. 46, 52  
Retake Forward Button [RETAKE F] .... pg. 29  
@ Stop Button [5, STOP] ......................... pg. 46  
# Play/Pause Button  
Other Parts  
o Battery Pack Mount ............................. pg. 10  
p Viewfinder........................................... pg. 16  
Q Grip Strap ............................................ pg. 16  
[
4/6, PLAY/PAUSE]............................. pg. 46  
$ Select Dial [+, , PUSH] .............. pg. 13, 36  
•Bright Dial [BRIGHT] ........................ pg. 21  
W Camera sensor  
Be careful not to cover this area; a sensor  
necessary for shooting is built-in here.  
•Remote Sensor .................................. pg. 61  
% MENU/DISPLAY Button ................. pg. 19, 36  
^ Counter Reset/Memory Button  
[COUNTER R/M] .............................. pg. 48  
•Recording Mode Button [SP/EP] ......... pg. 14  
E Video Light .......................................... pg. 30  
R Microphone  
& EJECT Switch ....................................... pg. 15  
* Recording Start/Stop Button.................. pg. 18  
( Power Switch .................... pg. 18, 22, 46, 52  
For use when recording.  
T Eyepiece .............................................. pg. 60  
Y Speaker ............................................... pg. 47  
U LCD Monitor ....................................... pg. 21  
I Shoulder Strap Eyelets .......................... pg. 17  
O Clock Battery Slot ................................ pg. 12  
P Tripod Mounting Socket ....................... pg. 17  
) Battery Release Switch  
[BATTERY RELEASE] ............................ pg. 10  
q PUSH Button ....................................... pg. 15  
INDEX Indications  
EN71  
1
2
3
4
5
6
30MIN  
REC SP  
T30  
7
%
FINE 12  
^
*
)
FADER  
8
0
&
(
2
01  
9
!
LENS COVER  
PAUSE  
1X  
a
15S  
5S  
BRIGHT  
TAPE END  
q
@
$
#
MERRY CHRISTMAS  
b
:
:
DEC 25. 99 AM 11 45 18  
1 Cassette Warning/  
% Battery Pack Remaining Power Indicator  
Changes as follows according to the battery  
pack’s remaining power level:  
Tape Remaining Time .......................... pg. 19  
When no cassette is inserted: the cassette (  
warning blinks.  
)
”. When the power is  
When the Erase Protection tab is not in the position  
almost gone, the indicator “ ” blinks (battery  
that allows recording: the cassette (  
) warning  
power warning), then the unit shuts off. Replace  
the battery pack with a fully charged one.  
Note: The symbol containing 3 darkened squares —  
— does not necessarily mean that the battery  
pack is fully charged.  
lights. Otherwise, the tape remaining time is  
displayed and the tape remaining time warning  
blinks when the tape is about to reach its end.  
When the Power Switch is set to “PLAY” and a  
tape is loaded: the cassette (  
regardless of the Erase Protection tab’s position.  
) mark is displayed  
^ Focus Indicator .................................... pg. 40  
& Exposure Control Level Counter ........... pg. 39  
2 Recording Mode (SP/EP) Indicator ........ pg. 14  
* White Balance Mode Indicator ............ pg. 42  
( •Record–Standby Mode Indicator ....... pg. 18  
•Lens Cover Warning:  
3, 8 Program AE Indicator ...................... pg. 32  
Displayed at 3 for approx. 2 seconds when  
Program AE with special effects is switched from  
one mode to another by pressing P.AE., then only  
the indicator remains at 8.  
LENS COVER .................................... pg. 19  
) Clock Battery Warning  
Blinks for approx. 10 seconds when the power is  
turned on. This display also blinks when the clock  
(lithium) battery is either not installed or has  
discharged. Install or replace the old battery with  
a new one (pg. 12).  
3, 9 Fade/Wipe-Standby Indicator .......... pg. 31  
Displayed at 3 for approx. 2 seconds when the  
Fade/Wipe is switched from one effect to another  
by pressing EFFECT, then only the indicator  
remains at 9.  
q Tape End Display: TAPE END ............ pg. 19  
Appears when the end of the tape is reached  
during playback, recording or fast-forward.  
Condensation Warning:  
4 •Picture Mode Display ................. pg. 23, 24  
Remaining Number Of Shots  
Indicator ..................................... pg. 23, 24  
5 Tape Length Indicator .......................... pg. 14  
6 Zoom Indicator Bar ............................. pg. 28  
When this indication appears, all functions  
except tape eject and power on/off are disabled.  
Turn the unit off (without removing the power  
source) for a few hours, and when you turn it on  
again the indication should disappear.  
Zoom Level Indicator  
Approximate Zoom Ratio  
7 Recording Indicator ............................. pg. 18  
Head Clog Warning:  
0 Picture Stabilizer Indicator ................... pg. 29  
Appears if dirty heads are detected during  
recording. In such a case, use the optional  
Cleaning Cassette. If, after using it, the problems  
still exist, consult your nearest JVC dealer.  
! Interval Timer/Recording Time  
Indicator ............................................. pg. 44  
@ •Bright Level Indicator ........................ pg. 47  
•Speaker Volume Indicator ................. pg. 47  
# Instant Title Display ............................. pg. 35  
$ Date/Time Display ............................... pg. 34  
INDEX Terms  
72  
EN  
A
F
AC Power Adapter/Charger ............................ pg. 10  
Animation Recording ..................................... pg. 45  
Auto Date Record .......................................... pg. 34  
Auto Focus .................................................... pg. 40  
Auto Shut Off ...........................................pg. 19, 46  
Fade-In/Out ................................................... pg. 31  
Fast-Forward Tape ......................................... pg. 46  
FINE Mode .................................................... pg. 24  
Full Image ................................................ pg. 23, 27  
G
B
Grip Adjustment ............................................ pg. 16  
Battery Pack .............................................pg. 10, 74  
Brighten The Image ....................................... pg. 39  
Brighten The LCD Monitor ............................. pg. 21  
H
High Speed Shutter Mode .............................. pg. 33  
I
C
INDEX Menu ................................................. pg. 56  
Index Mode ................................................... pg. 56  
Index Number ............................................... pg. 56  
Instant Titles .................................................. pg. 35  
Interface Shooting.......................................... pg. 21  
Car Battery ..................................................... pg. 11  
Cassette Adapter ............................................ pg. 49  
Charge Marker................................................ pg. 11  
Charging The Battery Pack ............................. pg. 10  
Clean The Camcorder .................................... pg. 65  
Clock (Lithium) Battery .................................. pg. 12  
COM Port (RS-232C) ..................................... pg. 53  
Connection To A VCR/TV .............................. pg. 50  
Connection To A Windows PC/Macintosh ...... pg. 53  
Contents .......................................................pg. 8, 9  
Counter Memory ........................................... pg. 48  
J
JLIP ID NO. ................................................... pg. 38  
Journalistic Shooting ...................................... pg. 21  
JPEG.............................................................. pg. 24  
L
LCD monitor/Viewfinder, Indications.............. pg. 71  
Load A Tape .................................................. pg. 15  
D
Darken The Image ......................................... pg. 39  
Darken The LCD Monitor .............................. pg. 21  
Date/Time Display ......................................... pg. 34  
Date/Time Settings ......................................... pg. 13  
DELETE Menu ............................................... pg. 58  
Delete Mode ................................................. pg. 58  
Delete Select Menu ....................................... pg. 58  
Demonstration Mode ..................................... pg. 38  
Digital Zoom ................................................. pg. 37  
Digital Still Camera ................................. pg. 22 – 25  
Diopter Adjustment ....................................... pg. 16  
Discharge The Battery Pack ........................... pg. 10  
M
Manual Focus................................................ pg. 41  
Menu Screen ...................................... pg. 37, 38, 55  
Modem Port .................................................. pg. 53  
Move The Page Back ..................................... pg. 52  
Move The Page Next ..................................... pg. 52  
N
ND Effect Mode............................................. pg. 33  
Nega/Posi Mode ............................................ pg. 33  
E
Electronic Fog Filter Mode ............................. pg. 33  
Erase Protection ............................................. pg. 15  
Exposure Control ........................................... pg. 39  
EN73  
P
T
Padlock Mark ................................................ pg. 57  
Picture Mode Setting ...................................... pg. 24  
Picture Stabilizer ........................................... pg. 29  
Pin-Up Image ........................................... pg. 23, 27  
Playback (D.S.C.)........................................... pg. 52  
Playback (VIDEO) .......................................... pg. 46  
Power Switch Position ................................... pg. 18  
Printer Port .................................................... pg. 53  
Program AE With Special Effects ...............pg. 32, 33  
PROTECT Menu ............................................ pg. 57  
Protect Mode ................................................. pg. 57  
Provided Accessories ....................................... pg. 9  
Tally .............................................................. pg. 38  
Tape Counter ................................................. pg. 46  
Tape Dubbing ...........................................pg. 50, 51  
Tape Length Setting........................................ pg. 14  
Tele Macro .................................................... pg. 38  
Time-Lapse Shooting ..................................... pg. 45  
Tracking ........................................................ pg. 47  
Tripod Mounting............................................ pg. 17  
Twilight Mode ............................................... pg. 33  
U
Unload A Tape .............................................. pg. 15  
V
Q
Video Light .................................................... pg. 30  
Viewfinder Adjustment .................................. pg. 16  
Quick Review ............................................... pg. 29  
R
W
Recording, Advanced Features (VIDEO) ... pg. 31 – 45  
Recording, Start/Stop (VIDEO) ................... pg. 18, 19  
Recording Mode ............................................ pg. 14  
Record-Standby ............................................. pg. 18  
Retake ........................................................... pg. 29  
Rewind The Tape........................................... pg. 46  
White Balance Adjustment............................. pg. 42  
Wide Mode ................................................... pg. 37  
Wipe-In/Out .................................................. pg. 31  
Z
Zooming ....................................................... pg. 28  
S
Self-Recording ............................................... pg. 21  
Self-Timer .................................................pg. 44, 61  
Sepia Mode ................................................... pg. 33  
Shooting,  
Advanced Features (D.S.C.) ............ pg. 32, 36 – 44  
Shooting (D.S.C.) .................................... pg. 22 – 25  
Shoulder Strap Attachment............................. pg. 17  
Shuttle Search................................................ pg. 48  
Slide Show Mode .......................................... pg. 55  
Snapshot Mode ........................................pg. 22, 26  
Snapshot (VIDEO) ..................................... pg. 26, 27  
Specifications ................................................ pg. 77  
Sports Mode .................................................. pg. 33  
STANDARD Mode......................................... pg. 24  
Star Mark On The Setting Menus ......... pg. 56, 57, 59  
Still Image Data Transfer ................................ pg. 53  
Still Playback ................................................. pg. 48  
Store A Still Image In The Built-In Memory ..... pg. 22  
Super LoLux (S.LX) ......................................... pg. 37  
CAUTIONS  
74  
EN  
DANGER:  
Battery Packs  
The battery packs are nickel-cadmium  
or nickel metal-hydride batteries.  
Before using the supplied battery pack  
or an optional battery pack, be sure to  
read the following cautions:  
Video Light  
The video light becomes extremely hot. Do not  
touch it either while in operation or soon after  
turning it off, otherwise serious injury may result.  
Do not place the camcorder into the carrying case  
immediately after using the video light, since it  
remains extremely hot for some time.  
1.To avoid hazard . . .  
... do not burn.  
Terminals  
... do not short-circuit the terminals.  
... do not modify or disassemble.  
... use only specified chargers.  
When operating, keep a distance of about 30 cm  
(1 ft.) between the video light and people or object.  
Do not use near flammable or explosive materials.  
It is recommended that you consult your nearest  
JVC dealer for replacing the video light.  
2. To prevent damage and prolong service life . . .  
... do not subject to unnecessary shock.  
... avoid repeated charging without fully discharg-  
ing.  
When using the AC Power Adapter/Charger in areas  
other than the USA  
The provided AC Power Adapter/Charger features  
automatic voltage selection in the AC range from  
110 V to 240 V.  
USING HOUSEHOLD AC PLUG ADAPTER  
In case of connecting the unit’s power cord to an AC  
wall outlet other than American National Standard  
C73 series type use an AC plug adapter, called a  
“Siemens Plug”, as shown.  
For this AC plug adapter, consult your nearest JVC  
dealer.  
... charge in an environment where temperatures  
are within the tolerances shown in the chart  
below. This is a chemical reaction type  
battery—cooler temperatures impede chemical  
reaction, while warmer temperatures can  
prevent complete charging.  
... store in a cool, dry place. Extended exposure to  
high temperatures will increase natural  
discharge and shorten service life.  
... avoid prolonged uncharged storage.  
... remove from charger or powered unit when  
not in use, as some machines use current even  
when switched off.  
Plug adapter  
NOTES:  
It is normal for the battery pack to be warm after  
charging, or after use.  
Temperature Range Specifications  
Charging .............. 10°C to 35°C (50°F to 95°F)  
Operation ............ 0°C to 40°C (32°F to 104°F)  
Storage ................ –10°C to 30°C (14°F to 86°F)  
Recharging time is based on room temperature of  
20°C.  
General Battery Precautions  
When the C-P6U or C-P7U (cassette adapter) is not  
functioning even when correctly operated, the  
battery is exhausted. Replace it with a fresh one.  
Use only the following battery:  
The lower the temperature, the longer recharging  
takes.  
C-P6U or C-P7U..................... AA (R6) size  
Please make note of the following rules for battery  
use. When misused, battery can leak or explode.  
1. Refer to the C-P6U/C-P7U instructions when  
replacing the battery.  
2. Do not expose the battery to excessive heat as it  
can leak or explode.  
3. Do not dispose of battery in a fire.  
4. Remove battery from the unit if it is to be stored for  
an extended period to avoid battery leakage which  
can cause malfunctions.  
CAUTIONS (cont.)  
EN75  
Cassettes  
To properly use and store your cassettes, be sure to  
read the following cautions:  
Main Unit  
1.For safety, DO NOT . . .  
... open the camcorder’s chassis.  
... disassemble or modify the unit.  
1.During use . . .  
... short-circuit the terminals of the battery pack.  
Keep it away from metallic objects when not in  
use.  
... allow inflammables, water or metallic objects  
to enter the unit.  
... remove the battery pack or disconnect the  
power supply while the power is on.  
... leave the battery pack attached when the  
camcorder is not in use.  
... make sure the cassette bears the VHS-C mark.  
... be aware that recording onto prerecorded tapes  
automatically erases the previously recorded  
video and audio signals.  
... make sure the cassette is positioned properly  
when inserting.  
... do not load and unload the cassette  
repeatedly without allowing the tape to run at  
all. This slackens the tape and can result in  
damage.  
2.Avoid using the unit . . .  
... in places subject to excessive humidity or dust.  
... in places subject to soot or steam such as near  
a cooking stove.  
... do not open the front tape cover. This exposes  
the tape to fingerprints and dust.  
2.Store cassettes . . .  
... in places subject to excessive shock or  
vibration.  
... away from heaters or other heat sources.  
... out of direct sunlight.  
... near a television set.  
... where they won’t be subject to unnecessary  
shock or vibration.  
... where they won’t be exposed to strong  
magnetic fields (such as those generated by  
motors, transformers or magnets).  
... vertically, in their original cases.  
... near appliances generating strong magnetic or  
electric fields (speakers, broadcasting antennas,  
etc.).  
... in places subject to extremely high (over 40°C  
or 104°F) or extremely low (under 0°C or 32°F)  
temperatures.  
3.DO NOT leave the unit . . .  
... in places of over 50°C (122°F).  
... in places where humidity is extremely low.  
(below 35%) or extremely high (above 80%).  
... in direct sunlight.  
... in a closed car in summer.  
... near a heater.  
4.To protect the unit, DO NOT . . .  
... allow it to become wet.  
... drop the unit or strike it against hard objects.  
... subject it to shock or excessive vibration during  
transportation.  
... keep the lens directed at extremely bright  
objects for long periods.  
... direct the eyepiece of the viewfinder at the sun.  
... carry it by holding the viewfinder or the LCD  
monitor. Be sure to hold the main unit with  
both hands or use the grip.  
... swing it excessively when using the shoulder  
strap.  
76  
EN  
LCD Monitor  
How to handle a CD-ROM  
Take care not to soil or scratch the mirror surface  
(opposite to the printed surface). Do not write  
anything or put a sticker on either the front or back  
surface. If the CD-ROM gets dirty, gently wipe it  
with a soft cloth outward from the center hole using  
a circular motion.  
1.To prevent damage to the LCD monitor, DO  
NOT . . .  
... push it strongly or apply any shocks.  
... place the camcorder with the LCD monitor on  
the bottom.  
2.To prolong service life . . .  
Do not use conventional disc cleaners or cleaning  
spray.  
... avoid rubbing it with coarse cloth.  
3.Be aware of the following phenomena for  
LCD monitor use. These are not malfunc-  
tions . . .  
While using the camcorder, the surface around the  
LCD monitor and/or the back of the LCD monitor  
may heat up.  
Do not bend the CD-ROM or touch its mirror  
surface.  
Do not store your CD-ROM in a dusty, hot or  
humid environment. Keep it away from direct  
sunlight.  
If you leave power on for a long time, the surface  
around the LCD monitor becomes hot.  
About moisture condensation . . .  
You may have observed that pouring a cold  
liquid into a glass will cause drops of water to  
form on the glass’ outer surface. This same  
phenomenon occurs on the head drum of a  
camcorder when it is moved from a cool place  
to a warm place, after heating a cold room,  
under extremely humid conditions or in a  
place directly subjected to the cool air from an  
air conditioner.  
Moisture on the head drum can cause severe  
damage to the video tape, and can lead to  
internal damage to the camcorder itself.  
Serious malfunctioning  
If malfunctioning occurs, stop using the unit  
immediately and consult your local JVC dealer.  
SPECIFICATIONS  
EN77  
Camcorder  
General  
Format  
: VHS NTSC standard  
: DC 6.0 V  
Operating temperature: 0°C to 40°C (32°F to 104°F)  
Operating humidity : 35% to 80%  
Storage temperature : –20°C to 50°C (–4°F to 122°F)  
Power source  
Power consumption  
LCD monitor off,  
viewfinder on  
LCD monitor on,  
viewfinder off  
LCD monitor on,  
viewfinder on  
Video light  
Weight  
Dimensions  
: Approx. 870 g (2.0 lbs)  
: 99 (W) x 119 (H) x 198 (D) mm  
(3-15/16" x 4-11/16" x 7-13/16")  
(with the LCD monitor closed  
and with the viewfinder fully  
tilted downward)  
: 6.9 W  
: 7.4 W  
: 8.0 W  
: 2.9 W  
: NTSC-type  
Pickup  
Lens  
: 1/4” format CCD  
Signal system  
Video recording system  
Luminance  
: F1.6, f = 3.9 to 62.4 mm, 16:1  
power zoom lens with auto iris  
and macro control, filter  
diameter 40.5 mm  
: FM recording  
Color  
: Converted sub-carrier  
direct recording  
Viewfinder  
: Electronic viewfinder  
with 0.55” color LCD  
Conforms to VHS standard  
Cassette  
Tape speed  
:
cassette  
White balance  
adjustment  
LCD monitor  
: Auto/Manual adjustment  
: 3” diagonally measured, LCD  
panel/TFT active matrix system  
: Monaural  
SP  
EP  
: 33.35 mm/sec. (1-5/16 ips)  
: 11.12 mm/sec. (7/16 ips)  
Recording time (max.)  
Speaker  
SP  
: 40 minutes  
EP  
: 120 minutes (with TC-40)  
Connectors  
JLIP  
D.S.C. format  
Recording format  
: ø3.5 mm, 4-pole, mini-head  
jack  
: Digital data storage (based on  
JPEG)  
(compatible with RC-5325 plug)  
: 1 Vp-p, 75 unbalanced,  
analog output  
Recording medium : Built-in flash memory,  
Video  
2 Mbyte  
Number of storable  
shots  
(via Video output connector)  
: FINE mode:  
Audio  
: –8 dBs, 1 kanalog output  
(via Audio output connector)  
: ø2.5 mm, 4-pole, mini-head  
jack  
approx. 30 shots  
STANDARD mode:  
approx. 60 shots  
: 640 x 480 pixels  
Digital  
Image size  
(when captured  
on a PC)  
Provided Accessories ..................  
pg. 9  
AC Power Adapter/Charger AA-V15U  
Power requirement  
U.S.A. and Canada : AC 120 V`, 60 Hz  
Other countries : AC 110 V to 240 V`, 50/60  
Hz  
Optional Accessories  
Battery Packs BN-V12U, BN-V20U, BN-V856U  
Car Battery Charger BH-V3U  
Battery Charger BH-VC10U  
Power consumption : 23 W  
Output  
Charge  
VTR  
Car Battery Cord AP-V7U  
: DC 8.5 V  
: DC 6.3 V  
, 1.3 A  
, 1.8 A  
Compact VHS-C Cassettes TC-40/30/20  
Active Carrying Bag CB-V7U  
Audio/Video Cable  
Charging system  
: Constant current, peak  
detection, timer controlled  
: 140 (W) x 42 (H) x 68 (D) mm  
(5-9/16” x 1-11/16” x 2-11/16”)  
: Approx. 300 g (0.71 lbs)  
Dimensions  
Weight  
Some accessories are not available in some areas. Please  
consult your nearest JVC dealer for details on accessories  
and their availability.  
Specifications shown are for SP mode unless otherwise  
indicated. E & O.E. Design and specifications subject to  
change without notice.  
Cassette Adapter C-P7U  
Dimensions  
: 188 (W) x 25 (H) x 104 (D) mm  
(7-7/16” x 1” x 4-1/8”)  
Weight  
Accessory  
: Approx. 240 g (0.53 lbs)  
: “AA (R6)”-size battery x 1  
MEMO  
MEMO  
EN  
VICTOR COMPANY OF JAPAN, LIMITED  
0P2ri9n9teMdKinV*JaUpNan*YP  
UM  
COPYRIGHT© 1999 VICTOR COMPANY OF JAPAN, LTD.  

ATN Fusion Image Intensification Thermal System FIITS14 User Manual
Attwood 4801 User Manual
Audiovox UB104W User Manual
Bushnell Binoculars 260228 User Manual
Canon HF R206 User Manual
Casio SE S300 User Manual
Directed Electronics 250 User Manual
Harman Kardon DPR 2005 User Manual
Honeywell AQUASTATIC L7224 User Manual
JVC AA V33U User Manual