JVC Everio GZ MG467 User Manual
EN  
GUIDEBOOK  
HARD DISK CAMCORDER  
U
GZ-MG467  
GZ-MG360  
GZ-MG335  
GZ-MG330  
U
U
U
Dear Customer  
Thank you for purchasing  
this hard disk camera. Before  
use, please read the safety  
information and precautions  
contained in pages 2 and 3 to  
ensure safe use of this product.  
For Future Reference:  
Enter the Model No. (located on  
the bottom of the camera) and  
Serial No. (located on the battery  
pack mount of the camera)  
below.  
Model No.  
Serial No.  
Remember that this camera is intended for  
private consumer use only.  
IMPORTANT SAFETY INSTRUCTIONS  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install  
in accordance with the manufacturer’s  
instructions.  
8. Do not install near any heat sources such  
as radiators, heat registers, stoves, or other  
apparatus (including amplifiers) that produce  
heat.  
9. Only use attachments/accessories specified by  
the manufacturer.  
Any commercial use without proper permission  
is prohibited. (Even if you record an event such  
as a show, performance or exhibition for personal  
enjoyment, it is strongly recommended that you  
obtain permission beforehand.)  
Trademarks  
Manufactured under license from Dolby  
•
Laboratories. Dolby and double-D symbol are  
trademarks of Dolby Laboratories.  
Windows® is either registered trademark or  
•
trademark of Microsoft Corporation in the United  
States and/or other countries.  
Macintosh is a registered trademark of Apple  
Inc.  
•
Other product and company names included  
•
in this instruction manual are trademarks  
and/or registered trademarks of their respective  
holders.  
10.Use only with the cart,  
stand, tripod, bracket,  
or table specified by  
the manufacturer,  
or sold with the  
apparatus. When a cart  
is used, use caution  
when moving the  
cart/apparatus combination to avoid injury from  
tip-over.  
11.Unplug this apparatus during lightning storms  
or when unused for long periods of time.  
12.Refer all servicing to qualified service  
personnel. Servicing is required when the  
apparatus has been damaged in any way, such  
as power-supply cord or plug is damaged,  
liquid has been spilled or objects have fallen  
into the apparatus, the apparatus has been  
exposed to rain or moisture, does not operate  
normally, or has been dropped.  
If this symbol is shown, it is only  
valid in the European Union.  
3
JVC Software License Agreement  
JVC SOFTWARE LICENSE AGREEMENT  
4 LIMITED WARRANTY  
JVC warrants that any media in which the  
Program is embodied are free from any defects  
in materials and workmanship for a period of  
thirty (30) days from the date of Your purchasing  
any our products accompanying the Program.  
JVC’s entire liability and your exclusive remedy  
in connection with the Program shall be  
replacement of such defective media. EXCEPT  
FOR THE EXPRESS WARRANTIES STATED  
HEREIN AND TO THE EXTENT PERMITTED BY  
APPLICABLE LAW, JVC AND ITS LICENSORS  
DISCLAIM ANY OTHER WARRANTIES, EITHER  
EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO IMPLIED WARRANTIES  
OF MERCHANTABILITY AND FITNESS FOR  
A PARTICULAR PURPOSE IN REGARD TO  
THE PROGRAM AND THE ACCOMPANYING  
PRINTED MATERIALS. SHOULD THERE BE  
ANY PROBLEM ARISING FROM OR CAUSED  
BY THE PROGRAM, YOU SHOULD SETTLE  
ALL SUCH PROBLEM AT YOUR OWN COST  
AND EXPENSE.  
IMPORTANT  
TO CUSTOMERS: PLEASE MAKE SURE TO  
READ THIS CAREFULLY BEFORE INSTALLING  
OR USING THE SOFTWARE PROGRAM  
NAMED “DIGITAL PHOTO NAVIGATOR”  
(“Program”) ON YOUR PC.  
The right to use the Program is granted by Victor  
Company of Japan, Limited (“JVC”) to You only  
on the condition that You agree to the following.  
Should You not agree to the terms hereof, You  
may not install or use the Program. HOWEVER,  
INSTALLING OR USING THE PROGRAM  
INDICATES YOUR ACCEPTANCE OF THESE  
TERMS AND CONDITIONS.  
1 COPYRIGHT; OWNERSHIP  
You acknowledge that all copyrights and other  
intellectual property rights in the Program are  
owned by JVC and its licensor, and remain  
vested in JVC and such licensor. The Program is  
protected under the copyright law of Japan and  
other countries, and related Conventions.  
5 LIMITED LIABILITY  
2 GRANT OF LICENSE  
TO THE EXTENT PERMITTED BY APPLICABLE  
LAW, IN NO EVENT SHALL JVC AND ITS  
LICENSORS BE LIABLE FOR ANY INDIRECT,  
SPECIAL, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES WHATSOEVER, REGARDLESS  
OF THE FORM OF ACTION WHETHER IN  
CONTRACT, TORT OR OTHERWISE ARISING  
OUT OF OR IN CONNECTION WITH THE USE  
OF OR INABILITY TO USE THE PROGRAM,  
EVEN IF JVC HAS BEEN ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES.YOU  
WILL INDEMNIFY AND HOLD HARMLESS  
JVC FROM ANY LOSS, LIABILITY OR  
COST ARISING OUT OF OR IN ANY WAY  
CONNECTED TO CLAIMS FROM ANY THIRD  
PARTY RELATING TO THE USE OF THE  
PROGRAM.  
(1) Subject to the conditions of this Agreement,  
JVC grants to You a non-exclusive right to  
use the Program.You may install and use the  
Program on a HDD or other storage devices  
incorporated in Your PC.  
(2) You may make one (1) copy of the Program  
solely for your personal backup or archival  
purposes.  
3 RESTRICTION ON THE PROGRAM  
(1) You may not reverse engineer, decompile,  
disassemble, revise or modify the Program,  
except to the extent that expressly permitted  
by applicable law.  
(2) You may not copy or use the Program, in  
whole or in part, other than as expressly  
specified in this Agreement.  
(3) You have no right to grant a license to use  
the Program, and may not distribute, rent,  
lease or transfer the Program to any third  
party or otherwise let them use the Program.  
4
NOTE  
6 TERM  
If You acquired the Program in Germany, the  
provisions of Sections 4 (Limited Warranty)  
and 5 (Limited Liability) provided above will be  
replaced with those of the German version of this  
Agreement.  
This Agreement will become effective on the date  
when You install and use the Program on Your  
machine, and continue to be in effect until the  
termination under the following provision.  
Should You breach any provision of this  
Agreement, JVC may terminate this Agreement  
without giving any notice to You. In this event,  
JVC may claim against You for any damages  
caused by Your breach. Should this Agreement  
be terminated, You must immediately destroy the  
Program stored in Your machine (including the  
erasing from any memory in Your PC), and no  
longer own such Program.  
CAUTIONS:  
Operate this equipment according to the  
operating procedures described in this manual.  
•
Use only the provided CD-ROM. Never use any  
other CD-ROM to run this software.  
•
Do not attempt to modify this software.  
Changes or modifications not approved by  
JVC could void user’s authority to operate the  
equipment.  
•
•
7 EXPORT CONTROL  
You agree that You will not ship, transfer or  
export the Program or underlying information  
and technology to any countries to which Japan  
and other relevant countries have initiated an  
embargo on such goods.  
How to handle a CD-ROM  
Take care not to soil or scratch the mirror  
•
surface (opposite to the printed surface). Do  
not write anything or put a sticker on either  
the front or back surface. If the CD-ROM  
gets dirty, gently wipe it with a soft cloth  
outward from the center hole.  
8 U.S. GOVERNMENT USER  
If You are an agency of the United States of  
America (the “Government”), You acknowledge  
JVC’s representation that the Program is  
a “Commercial Item” as defined in Federal  
Acquisition Regulation (FAR) part 2.101 (g)  
consisting unpublished “Commercial Computer  
Software” as those items are used at FAR part  
12.212 and is only licensed to You with the same  
use rights JVC grants all commercial end users  
pursuant to the terms of this Agreement.  
Do not use conventional disc cleaners or  
cleaning spray.  
•
Do not bend the CD-ROM or touch its mirror  
surface.  
•
Do not store your CD-ROM in a dusty, hot or  
humid environment. Keep it away from direct  
sunlight.  
•
9 GENERAL  
(1) No modification, change, addition, deletion  
or other alternation of or to this Agreement  
will be valid unless reduced to writing and  
signed by an authorized representative of  
JVC.  
You can find the latest information (in  
English) on the provided software program at  
our world wide web server at http://www.jvc-  
victor.co.jp/english/global-e.html  
(2) If any part of this Agreement is held  
invalid by or in conflict with any law having  
jurisdiction over this Agreement, the  
remaining provisions will remain in full force  
and effect.  
(3) This Agreement shall be governed by and  
interpreted under the laws of Japan. The  
Tokyo District Court has jurisdiction over all  
disputes which may arise with respect to the  
execution, interpretation and performance of  
this Agreement.  
Victor Company of Japan, Limited  
5
Read This First!  
How to Select an Item Using the Touch Sensor  
An example screen in English is used for the guidance below.  
Selecting an item from the menu list  
(on the menu screen ੬ pg. 62)  
Using on-screen buttons  
(e.g. during playback ੬ pg. 27)  
L
L
A
MENU  
IMAGE QUALITY  
IMAGE SIZE  
Q
GAIN UP  
BASIC SETTINGS  
B
R
A
B
To select an on-screen button appearing  
on the left side, touch the portion of the  
sensor next to the on-screen button.  
QSlide your finger up and down on the  
sensor.  
RTouch the OK button.  
To select an on-screen button appearing at  
the bottom of the screen, touch the touch  
sensor under the on-screen button you  
want to select.  
NOTE  
The cursor moves from 1 to 9 on the index  
screen when you slide your finger on the  
touch sensor.  
CAUTION  
Touch the sensors with your finger. The  
sensors do not function if you touch them with  
your finger nail or with gloves on.  
6
Make a backup of important recorded data  
JVC will not be responsible for any lost data. It is recommended to copy your important  
recorded data to a DVD or other recording media for storage. (੬ pg. 42)  
Make a trial recording  
Before the actual recording of important data, make a trial recording and play back the  
recorded data to check that the video and sound have been recorded correctly.  
Reset the camera if it does not operate correctly  
This camera uses a microcomputer. Factors such as background noise and interference  
can prevent it from operating correctly. If the camera does not operate correctly, reset the  
camera. (੬ pg. 67)  
Precautions on handling batteries  
Be sure to use the JVC BN-VF808U/VF815U/VF823U battery packs.  
If the camera is subjected to electrostatic discharge, turn the power off before using it  
again.  
•
•
If a malfunction occurs, stop using the camera immediately  
and consult your local JVC dealer  
If a problem occurs when using the microSD card, take the card together with the  
camera for repair. If one of them is not included, the cause of the malfunction cannot be  
diagnosed, and the camera cannot be repaired.  
•
Recorded data may be erased while the camera is being repaired or inspected. Back up  
all data before requesting repairs or inspections.  
•
Because the camera may be used for demonstration in a shop,  
the demonstration mode is set to [ON] by default  
To deactivate the demonstration mode, set [DEMO MODE] to [OFF]. (੬ pg. 64)  
When connecting the camera to other devices using an  
optional DV cable, make sure to follow the procedure below.  
Connecting the cable incorrectly may cause malfunctions to  
the camera and/or other devices.*  
Connect the DV cable first to the device, and then to the camera.  
Connect the DV cable (plugs) correctly according to the shape of the DV connector.  
* This does not apply to the GZ-MG360/330 model.  
•
•
7
Contents  
GETTING STARTED  
EDITING/PRINTING  
Accessories .......................................... 10  
How to Use the Everio Dock* ......................10  
Attaching the Shoulder Strap.......................11  
Preparing the Remote Control.....................11  
Attaching the Core Filter  
Managing Files...................................... 32  
Deleting/Protecting Files..............................32  
Viewing File Information ..............................33  
Changing the Event Registration of Video  
Files after Recording..................................34  
Partial Delete (EDITED COPY) ...................35  
to the USB Cable .......................................11  
Index ...................................................... 12  
Indications on LCD Monitor................. 14  
Necessary Settings before Use........... 16  
Charging the Battery Pack...........................16  
Date/Time Setting........................................17  
Language Setting ........................................17  
Playlists................................................. 36  
Creating Playlists.........................................36  
Playing Back Playlists..................................37  
Other Operations of Playlists.......................38  
Print Setting .......................................... 39  
DPOF Print Setting......................................39  
Direct Printing with PictBridge Printer .........40  
Other Settings....................................... 18  
Grip Adjustment...........................................18  
Lens Cover ..................................................18  
Checking the Remaining Battery Power......18  
Tripod Mounting...........................................18  
When Using a microSD Card ......................19  
COPYING  
Copying Files........................................ 42  
Using a DVD Burner to Copy Files from the  
Camera ......................................................42  
Using a VCR/DVD Recorder to Dub Files from  
the Camera ................................................46  
Using the Camera to Dub Files from a VCR/  
DVD Player.................................................47  
Copying/Moving Files ..................................48  
RECORDING  
Recording Files..................................... 20  
Video Recording..........................................20  
Still Image Recording ..................................21  
Zooming.......................................................22  
LED Light.....................................................22  
Registering Files to Events..........................23  
Checking the Remaining Space on the  
Recording Media........................................23  
Manual Recording ............................... 24  
To Change to Manual Recording Mode.......24  
Program AE.................................................24  
Backlight Compensation..............................24  
Manual Setting in Function Menu................25  
Playing Back Files................................ 27  
Video/Still Image Playback ..........................27  
File Search Function....................................28  
To Play Back MPG Files ..............................29  
Playback with Special Effects......................30  
Watching Images on TV........................ 31  
8
PC OPERATION  
Regarding the Icons in this  
Manual  
File Backup on a Windows® PC........... 49  
System Requirements .................................49  
Software Installation ....................................50  
Connecting the Camera to the PC...............51  
File Backup on the PC.................................52  
File Backup on the PC without Using  
Icon at the top of a page  
Software.....................................................53  
Other Windows® PC Operations.......... 54  
Playing Back Files on the PC ......................54  
Creating a DVD-Video .................................55  
Getting More Use of the Software ...............57  
When there is an icon at the top of a page,  
it shows whether the page is related to  
videos or still images.  
File Backup on a Macintosh® .............. 58  
System Requirements .................................58  
Connecting the Camera to the Macintosh ...58  
File Backup on the Macintosh .....................59  
Page related to videos  
!
#
Page related to still images  
Folder Structure and Extensions........ 60  
Customer Support Information ........... 61  
Icon at the subtitle  
MENU SETTINGS  
Changing the Menu Settings............... 62  
FURTHER INFORMATION  
Troubleshooting.................................... 67  
Warning Indications ............................. 70  
Cleaning ................................................ 71  
Specifications ....................................... 72  
Cautions ................................................ 74  
Terms..................................................... 76  
For video mode only  
!
#
For still images mode only  
On-screen function guide  
The on-screen function guide is displayed  
at the bottom of the screen during menu  
display, etc.  
9
GETTING STARTED  
Accessories  
Battery Pack  
BN-VF815U  
(GZ-MG467)  
Battery Pack  
BN-VF808U  
(GZ-MG360/335/330)  
Everio Dock*  
CU-VC4U (੬ below)  
AC Adapter  
AP-V18U/14U  
Audio/Video Cable  
USB Cable  
(੬ pg. 40, 42, 51  
and 58)  
Shoulder Strap  
(੬ pg. 11)  
CD-ROM  
(੬ pg. 50)  
NOTE  
Make sure to use the  
provided cables for  
connections. Do not  
use any other cables.  
Remote Control Unit  
RM-V751U (੬ pg. 11)  
Lithium Battery  
CR2025  
Pre-installed in the  
remote control unit.  
Core Filter  
(੬ pg. 11)  
How to Use the Everio Dock*  
You can connect cables to the connectors of the Everio dock. The connection is completed when  
you place the camera on the dock.  
S-Video Jack  
Camera Connection  
Terminal  
AV Jack  
DC Jack  
DV Jack  
USB Jack  
NOTE  
For the connection using the S-Video jack and DV jack, an optional S-Video cable and DV cable  
are needed. Consult the JVC Service Center described on the sheet included in the package for  
details on its availability. Make sure to connect the end with a core filter to the camera. The core  
filter reduces interference.  
The S-Video cable (optional) enables even higher playback quality on TV. (੬ pg. 31) Be sure  
to use the YTU94146A S-Video cable.  
•
When dubbing files from the camera with a VCR/DVD recorder (੬ pg. 47), using the DV cable  
enables even higher dubbing quality. Be sure to use the VC-VDV204U DV cable. Operation  
using the DV cable is not guaranteed on all devices.  
•
* GZ-MG360/330 model does not include the Everio dock.  
10  
Attaching the Shoulder Strap  
Peel off the pad and thread  
the end of the strap through  
the eyelet.  
Thread the strap through the  
Position the buckle near the  
buckle, adjust its length, and use eyelet and reattach the pad.  
the strap guide to fix it in place.  
Buckle  
Strap Guide  
Eyelet  
Preparing the Remote Control  
A battery is included inside the remote control at the time of purchase.  
Remove the insulation sheet before use.  
Effective Beam Distance  
Remote Sensor  
To Reinsert the Battery  
Pull out the battery holder by pressing the  
lock tab.  
Lock Tab  
Lithium Battery  
(CR2025)  
Effective distance:  
5 m (16 ft)  
NOTE  
The transmitted beam may not be effective  
or may cause incorrect operation when the  
remote sensor is directly exposed to sunlight  
or powerful lighting.  
Attaching the Core Filter to the USB Cable  
Attach the core filter to the USB cable. The core filter reduces interference. Connect the end of  
the cable with the core filter to the camera.  
Release the stopper.  
3 cm (1-3/16")  
Wind once.  
11  
Index  
NOTES  
The LCD monitor can rotate 270°.  
•
Power-linked operation  
•
You can also turn the camera on/off by  
opening/closing the LCD monitor during the  
recording mode.  
Be careful not to cover 4, 5, 7and 9  
during shooting.  
•
12  
Camera  
Remote Control  
! Touch Sensor (੬ pg. 6)  
# OK (DISP) Button [OK/DISP] (੬ pg. 15)  
$ Menu Button [MENU]  
Q Infrared Beam Transmitting Window  
R ZOOM (T/W) Buttons  
Zoom In/Out (੬ pg. 22)  
S Up Button  
% Power Switch [POWER]  
(You can turn off the camera by pressing  
and holding this button.)  
& Speaker  
Rotate Button (counterclockwise)  
(੬ pg. 27)  
T Skip Backward Button  
U Left Button  
( Playback/Recording Mode Switching  
Button [SELECT PLAY/REC] (੬ pg. 20)  
) Access/Charge Lamp [ACCESS/CHARGE]  
(Blinks when you access files or charge  
the battery. Do not turn off the power or  
remove the battery pack/AC adapter while  
accessing files.)  
* Direct DVD Button [DIRECT DVD]  
(੬ pg. 43)/Title Button [TITLE] (੬ pg. 37)  
+ Direct Backup Button [DIRECT BACK  
UP] (੬ pg. 52)/Information Button [INFO]  
(੬ pg. 33)  
V Back Button  
W PLAYLIST Button (੬ pg. 36)  
X START/STOP Button  
Y SNAPSHOT Button (੬ pg. 21)  
Z INFO Button (੬ pg. 33)  
a Skip Forward Button  
b PLAY/PAUSE Button  
c Right Button  
d Next Button  
e Down Button  
Rotate Button (clockwise) (੬ pg. 27)  
f INDEX Button  
g DISP Button  
, Auto/Manual Mode Button [AUTO/  
MANUAL] (੬ pg. 24)  
- Video Recording Start/Stop Button [START/  
STOP] (੬ pg. 20)  
. Still Image Shooting Button [SNAPSHOT]  
(੬ pg. 21)  
/ Zoom Lever [W 7,T ] (੬ pg. 22)  
,
Speaker Volume Control [–VOL+]  
(੬ pg. 27)  
0 Mode Switch [!, #]  
1 DC Jack [DC] (੬ pg. 16)  
2 Audio/Video Jack [AV]  
3 USB (Universal Serial Bus) Jack [  
]
2
(੬ pg. 40, 42, 51 and 58)  
4 LED Light (੬ pg. 22)  
5 Camera Sensor  
Remote Sensor (੬ pg. 11)  
6 Lens Cover (੬ pg. 18)  
7 Lens  
8 Lens Cover Switch [  
,
] (੬ pg. 18)  
=>  
9 Stereo Microphone  
: microSD Card Slot (੬ pg. 19)  
; Stud Hole (੬ pg. 18)  
< Tripod Mounting Socket (੬ pg. 18)  
= Battery Release Button [BATT.] (੬ pg. 16)  
> Battery Pack Mount (੬ pg. 16)  
? Grip Strap (੬ pg. 18)  
13  
Indications on LCD Monitor  
During both Video and Still Image  
Recording  
During Video Recording Only  
! Mode Indicator (੬ pg. 20)  
# Counter  
$ Picture Quality:  
B
! Selected Operation Mode Indicator  
(੬ pg. 24)  
(FINE),  
C
D
(੬ pg. 62)  
% Remaining Time (੬ pg. 20, 73)  
REC: (Appears during recording.)  
4: Auto Mode  
3: Manual Mode  
&
M
# Effect Mode Indicator (੬ pg. 26)  
$ Tele Macro Mode Indicator (੬ pg. 26)  
% LED Light Indicator (੬ pg. 22)  
& Program AE Mode Indicator (੬ pg. 24)  
( AV/S-Video Input Jack Indicator*  
(੬ pg. 63)  
(੬ pg. 20)  
: (Appears during record-standby  
mode.)  
( Digital Image Stabilizer (DIS) Indicator  
(Appears when [DIS] is set to [OFF].)  
(੬ pg. 63)  
MQ  
) Zoom Indicator (੬ pg. 22)  
* Selected Medium Indicator (੬ pg. 64)  
+ Drop Detection Indicator (Appears when  
[DROP DETECTION] is set to [OFF].)  
(੬ pg. 64)  
, Approximate Zoom Ratio (੬ pg. 22)  
- White Balance Indicator (੬ pg. 26)  
. Manual Focus Adjustment Indicator  
(੬ pg. 25)  
) Wind Cut Indicator (੬ pg. 63)  
* Event Indicator (੬ pg. 23)  
During Still Image Recording Only  
/ Battery Indicator (੬ pg. 70)  
0 Date/Time (੬ pg. 17)  
1 Brightness Control Indicator (੬ pg. 64)  
2 Backlight Compensation Indicator  
(੬ pg. 24)  
! Mode Indicator (੬ pg. 21)  
# Focus Indicator (੬ pg. 25)  
$ Image Size (੬ pg. 63)  
% Picture Quality: FINE (fine) or STD  
(standard) (੬ pg. 62)  
& Remaining Number of Shots (੬ pg. 73)  
( Shooting Indicator (੬ pg. 21)  
) Shutter Mode Indicator (੬ pg. 62)  
* Self-Timer Recording Indicator (੬ pg. 62)  
3 Iris Lock Indicator (੬ pg. 25, 26)  
4
: Exposure Adjustment Indicator  
(੬ pg. 25)  
.: Photometry Area Control Indicator  
(੬ pg. 26)  
5 Shutter Speed (੬ pg. 26)  
* This does not apply to the GZ-MG360/330  
model.  
14  
During Video Playback  
During Still Image Playback  
! Mode Indicator (੬ pg. 27)  
# Effect Mode Indicator (੬ pg. 30)  
$ Wipe/Fader Effect Indicator (੬ pg. 30)  
! Mode Indicator (੬ pg. 27)  
# Effect Mode Indicator (੬ pg. 30)  
$ Folder/File Number  
% Slide Show Playback Indicator (੬ pg. 27)  
& Selected Medium Indicator (੬ pg. 64)  
( Drop Detection Indicator (Appears when  
[DROP DETECTION] is set to [OFF].)  
(੬ pg. 64)  
%
: Playlist Playback Indicator (Appears  
6
when playing back a playlist.) (੬ pg. 37)  
¨ª: Event Search Playback Indicator  
(Appears when playing back a video file  
from the event search.) (੬ pg. 28)  
¨©: Date Search Playback Indicator  
(Appears when playing back a video file  
from the date search.) (੬ pg. 28)  
) Battery Indicator (੬ pg. 70)  
* Date/Time (੬ pg. 17)  
& Picture Quality:  
(ULTRA FINE),  
B
(FINE),  
(NORMAL),  
(ECONOMY)  
C
D
E
(੬ pg. 23, 62)  
( Counter  
) Playback Mode (੬ pg. 27)  
:Playback  
F
:Pause  
Q
:Forward Search  
:Reverse Search  
Switching indication modes on LCD  
monitor  
K
J
:Forward Slow-Motion  
:Reverse Slow-Motion  
G
E
Each time you touch the DISP button,  
indications on LCD monitor switch as  
shown below;  
(The number on the left shows speed.)  
* Selected Medium Indicator (੬ pg. 64)  
+ Drop Detection Indicator (Appears when  
[DROP DETECTION] is set to [OFF].)  
(੬ pg. 64)  
, Volume Level Indicator  
- Battery Indicator (੬ pg. 70)  
. Date/Time (੬ pg. 17)  
In recording mode:  
All indications/Indications for selected  
functions  
In playback mode:  
All indications/Only date and time/  
No indications  
15  
Necessary Settings before Use  
Be sure to configure the following three  
settings before use.  
The charge lamp blinks to indicate charging  
has started.  
When the lamp goes out, charging is  
finished. Unplug the AC adapter from the  
AC outlet and disconnect the AC adapter  
from the camera.  
•
•
Charging the Battery Pack  
1
Close the LCD monitor to turn off the  
To detach the battery pack  
Slide and hold BATT. (੬ step 2), then  
remove the battery pack.  
L
L
camera.  
To check the remaining battery power  
See page 18.  
2
Attach the battery pack.  
Slide the battery pack down until it locks  
in place.  
NOTES  
Bottom of the Camera  
BATT.  
You can also use the camera with just the  
AC adapter.  
Please do not pull or bend the AC adapter  
plug and cable. This may damage the AC  
adapter.  
•
•
3
Connect the AC adapter.  
DC Jack  
AC Adapter  
To AC Outlet  
(110V to 240V)  
You can also connect the AC adapter using  
•
the Everio dock connector.* (੬ pg. 10)  
* GZ-MG360/330 model does not include  
the Everio dock.  
16  
Date/Time Setting  
Language Setting  
The language on the display can be changed.  
1
2
Open the LCD monitor to turn on the  
camera.  
1
Open the LCD monitor to turn on the  
camera.  
When [SET DATE/TIME!] appears,  
select [YES] within 10 seconds.  
2
Touch the MENU button.  
3
Select [BASIC SETTINGS].  
If you do not select within 10 seconds, the  
screen disappears. In such case, press  
the POWER button and turn the camera  
on again.  
4
Select [LANGUAGE].  
3
Set the date and time.  
Repeat this step to input the month, day,  
year, hour and minute.  
5
Select the desired language.  
4
Touch the OK button to finish.  
To change the date and time  
1) Touch the MENU button.  
2) Select [BASIC SETTINGS], and then  
[CLOCK ADJUST].  
L
To return to the previous screen  
L
L
Select  
.
@
To quit the screen  
Touch the MENU button.  
3) Set the date and time.  
To return to the previous screen  
L
L
Select  
.
@
To quit the screen  
Touch the MENU button.  
You have now finished configuring the  
necessary settings.  
To use the camera right away  
See page 20.  
L
To configure other settings  
See page 18.  
L
17  
Other Settings  
NOTES  
Grip Adjustment  
If “COMMUNICATING ERROR” appears,  
•
there may be a problem with your battery.  
In such a case, consult your nearest JVC  
dealer.  
Open the pad and make grip adjustments.  
The recordable time display should only be  
used as a guide. It is displayed in 10 minute  
units.  
•
Tripod Mounting  
Align the camera stud hole with the tripod  
stud, and the mounting socket with the screw,  
and then rotate the camera clockwise to  
mount it to the tripod.  
Lens Cover  
When not using the camera, close the lens  
cover to protect the lens.  
Bottom of the  
Camera  
Open the lens cover  
Close the lens cover  
NOTE  
Do not push the lens cover strongly. Doing so  
may cause damage to the lens.  
NOTE  
Do not use a tripod on unsteady or unlevel  
surfaces. It could tip over, causing serious  
damage to the camera.  
Checking the Remaining Battery  
Power  
•
Preparation:  
Attach the battery pack.  
Press the SELECT PLAY/REC button to  
select recording mode.  
•
•
For !mode:  
Press the INFO button twice or the INFO  
button and then select  
.
;
For #mode:  
Press the INFO button.  
DIRECT  
BACK UP  
INFO  
To return to the normal screen  
Press the INFO button again.  
L
18  
NOTES  
When Using a microSD Card  
Insert and remove the microSD card only  
•
while the power is turned off. Otherwise,  
data on the card may be corrupted.  
Do not touch the terminal on the reverse  
side of the label.  
If you want to record to a microSD card,  
the following three operations need to be  
performed.  
Operations are certified on the following  
microSD cards.  
•
•
Video recording: Class 4 or higher  
compatible microSDHC card (4 GB)  
Still image recording: Panasonic, TOSHIBA,  
SanDisk, ATP microSD card (256 MB to  
2 GB) or microSDHC card (4 GB)  
If other media are used, they may fail to  
record data correctly, or they may lose data  
that had already been recorded.  
RChange the recording medium  
The camera is programmed to record on the  
built-in hard disk when it is shipped from the  
factory.You can change the recording medium  
to microSD card.  
•
Set [REC MEDIA FOR VIDEO] and [REC  
MEDIA FOR IMAGE] to [SD]. (੬ pg. 64)  
MultiMediaCards are not supported.  
Cards used to record video on this camera  
•
•
cannot be played back on other devices.  
QInsert a microSD card  
SFormat a microSD card when using it  
for the first time  
Preparation:  
Close the LCD monitor to turn off the camera.  
This will also ensure stable speeds and  
operation when accessing the microSD card.  
1
Open the microSD card cover.  
Select [FORMAT SD CARD] to format  
the card. (੬ pg. 65)  
Bottom of the  
Camera  
2
Firmly insert the card with its clipped  
edge first.  
Clipped Edge  
3
Close the microSD card cover.  
To remove a microSD card  
Push the microSD card once.  
L
After the card comes out a little, pull it out.  
19  
RECORDING  
Recording Files  
Video Recording  
Preparation: Open the LCD monitor to turn on the camera.  
Slide the mode switch to select  
!(video) mode.  
Press the SELECT PLAY/REC  
button to select recording mode.  
SELECT  
PLAY/REC  
Press the START/STOP button to  
start recording.  
Approximate remaining time for  
recording appears.  
LTo stop recording  
LTo register a file to an event  
See page 23.  
Press the START/STOP button again.  
LTo view the video you just recorded  
Select A during pause.  
LTo change the aspect ratio of the image  
(16:9/4:3)  
During the preview, you can delete the  
video by selecting *.  
Change the settings in [SELECT ASPECT  
RATIO]. (੬ pg. 63)  
LTo change the picture quality  
Change the settings in [VIDEO QUALITY].  
(੬ pg. 62)  
NOTES  
The video recording mode is automatically selected when you turn the camera’s power off and then  
on again.  
If the camera is not operated for 5 minutes while the power is on, it turns itself off automatically to  
conserve power. To turn the camera on again when using the battery pack, close the LCD monitor  
and open it again. When using the AC adapter, perform any operation such as zooming.  
Video files are given the names MOV001.MOD to MOV009.MOD, MOV00A.MOD to MOV00F.MOD,  
and MOV010.MOD in order of recording.  
•
•
•
After recording video for 12 consecutive hours, recording stops automatically.  
A new file will be created for every 4 GB of continuous shooting.  
This camera records video in MPEG2 format compliant with SD-VIDEO format. This camera is not  
compatible with other digital video formats.  
•
•
•
Do not move or shake the camera suddenly during recording. If you do so, the driving sound (hum) of  
the hard disk may be recorded.  
•
20  
Still Image Recording  
Preparation: Open the LCD monitor to turn on the camera.  
Slide the mode switch to select  
#(still image) mode.  
Press the SELECT PLAY/REC  
button to select recording mode.  
SELECT  
PLAY/REC  
Press and hold the SNAPSHOT  
button halfway.  
The ?indicator becomes green when  
the captured image is focused.  
LTo view the image you just recorded  
Select A after shooting.  
Press the SNAPSHOT button fully  
to take the photo/picture.  
During the preview, you can delete the  
image by selecting *.  
LTo change the picture quality  
Change the settings in [IMAGE  
QUALITY]. (੬ pg. 62)  
LTo record still images continuously  
Set to [CONTINUOUS SHOOTING] in  
[SHUTTER MODE]. (੬ pg. 62)  
LTo change the image size  
Change the settings in [IMAGE SIZE].  
(੬ pg. 62)  
NOTES  
DIS (Digital Image Stabilizer) does not function during still image recording.  
If the camera is not operated for 5 minutes while the power is on, it turns itself off automatically to  
conserve power. To turn the camera on again when using the battery pack, close the LCD monitor  
and open the LCD monitor again. When using the AC adapter, perform any operation such as  
zooming.  
•
•
21  
Recording Files (Continued)  
Zooming  
LED Light  
Preparation:  
Preparation:  
Slide the mode switch to select !or #  
Slide the mode switch to select !or #  
•
•
mode.  
mode.  
Press the SELECT PLAY/REC button to  
select recording mode.  
Press the SELECT PLAY/REC button to  
select recording mode.  
•
•
Zoom out  
Zoom in  
1
2
3
Touch the MENU button.  
Select [LIGHT].  
W: Wide angle  
T: Telephoto  
Select the desired setting.  
Zoom Ratio (Factory-preset)  
The light remains on regardless  
of the surrounding conditions.  
D
Model  
!mode  
#mode  
GZ-MG467  
64X  
27X  
The light turns on automatically  
when shooting in insufficient light  
conditions.  
DA  
GZ-MG360  
GZ-MG335  
GZ-MG330  
70X  
35X  
Disables this function.  
No display  
LTo change the maximum zoom ratio (for  
!mode only)  
Change the settings in [ZOOM]. (੬ pg. 63)  
NOTE  
Macro shooting is possible as close as  
approx. 5 cm (2") to the subject when the  
zoom lever is set all the way to W.  
22  
Checking the Remaining Space  
on the Recording Media  
Registering Files to Events  
!
!
If you select an event to register the file to  
before starting recording, the file will be  
Preparation:  
registered to the selected event, thus making  
the file easy to find at playback. There are  
up to three different destinations within each  
event (for example: BABY1, BABY2, BABY3).  
Slide the mode switch to select !mode.  
Press the SELECT PLAY/REC button to  
select recording mode.  
•
•
Press the INFO button.  
Preparation:  
Slide the mode switch to select !mode.  
Press the SELECT PLAY/REC button to  
select recording mode.  
•
DIRECT  
BACK UP  
•
INFO  
1
2
Touch the MENU button.  
The maximum recording time is displayed for  
each picture quality mode  
Select [REGISTER EVENT].  
( B: ULTRA FINE, C: FINE, D: NORMAL,  
E: ECONOMY).  
LTo change the picture quality  
1) Select the desired picture quality.  
2) Touch the OK button.  
3
LTo return to the normal screen  
Select the event that you want to  
register the file to.  
Select @.  
To select a different destination, select  
[SORT].  
•
To cancel the event registration, select  
[CANCEL].  
•
The selected event is displayed on the  
screen. Press the START/STOP button to  
start recording.  
LTo quit the screen  
Select [QUIT].  
LTo search a file by the event  
See page 28.  
NOTE  
Once you register a file to a certain event, the  
setting will remain even if you turn the power  
off. Unless you change the setting, you will  
register a file to the same event that you had  
previously selected.  
23  
Manual Recording  
Manual recording mode enables you to set  
the focus and screen brightness etc. manually.  
LItems for program AE setting  
5 NIGHT:  
•
Records with more sensitivity in dim  
locations by adjusting the shutter speed  
automatically.  
To Change to Manual Recording  
Mode  
3 TWILIGHT:  
•
Makes evening scenes look more natural.  
Preparation:  
6PORTRAIT:  
Slide the mode switch to select !or #  
•
•
The subject in the foreground is  
mode.  
accentuated by blurring the background.  
Press the SELECT PLAY/REC button to  
select recording mode.  
•
HSPORTS:  
•
Records fast moving subjects clearly.  
GSNOW:  
Press twice.  
•
Compensates for subjects that may  
appear too dark when shooting in  
extremely bright surroundings, such as  
in snow.  
AUTO  
/
MANUAL  
/SPOTLIGHT:  
•
Select this when a spotlight makes a  
subject appear too bright.  
LTo return to the auto recording mode  
Press the AUTO/MANUAL button so that  
the 4indicator appears.  
Backlight Compensation  
Backlight compensation brightens the subject  
by increasing the exposure.  
Program AE  
After performing “To Change to Manual  
Recording Mode” (੬ left column)  
You can record videos or still images with  
optimum brightness by adjusting the exposure  
and shutter speed to suit your surroundings or  
the subject.  
1
Touch the MENU button.  
After performing “To Change to Manual  
2
Recording Mode” (੬ above)  
Select [BACKLIGHT COMP.].  
1
Touch the MENU button.  
3
Set to [ON].  
2
Select [PROGRAM AE].  
3
Select the desired setting.  
LTo cancel backlight compensation  
Select @.  
For details on each setting, see the right  
column.  
LTo cancel program AE  
Select [OFF] in step 2.  
24  
4
Select the desired setting.  
Manual Setting in Function Menu  
You can use manual recording functions  
easily by selecting items in the function  
menus.  
After performing “To Change to Manual  
Recording Mode” (੬ pg. 24)  
Depending on the kind of settings you  
select, you can set the value by using the  
touch sensor.  
1
Touch the MENU button.  
The menu disappears and the indicator for  
the set function appears.  
2
Select [MANUAL SETTING].  
3
Select the desired menu.  
For details on each menu, see below.  
LTo return to the previous screen  
Select @.  
LTo quit the screen  
Touch the MENU button.  
Menus  
Settings: [ ] = Factory-preset  
For !mode  
[AUTO]: The brightness is adjusted automatically.  
–6 to +6: Corrects the brightness within this range in increments of 1.  
For #mode  
ADJUST BRIGHTNESS  
Adjusts the brightness.  
[ 0]: The brightness is not adjusted.  
–2.0 to +2.0 (EV): Corrects the brightness within this range in  
increments of 1/3EV.  
LTo lock the exposure  
When the menu disappears after you finish configuring the  
setting, select [LOCK]. The Cindicator appears.  
[AUTO]: The focus is adjusted automatically.  
@9:A: Adjusts the focus manually. (When zooming, the  
subject will not go out of focus if you adjust the focus at the  
telephoto (T) side before zooming to the wide-angle (W)  
side.)  
FOCUS  
Adjusts the focus.  
25  
Manual Recording (Continued)  
Menus  
Settings: [ ] = Factory-preset  
[AUTO]: White balance is adjusted automatically.  
@
BMWB: Adjusts the white balance manually depending on the  
light source.  
1) Hold a sheet of plain white paper in front  
of the subject so that the white paper fills  
the screen.  
2) Keep touching the OK button until the  
Bindicator starts blinking then stops  
blinking.  
WB  
Adjusts the white balance  
to achieve the optimum  
colors for the amount of  
light in your surroundings  
during recording.  
DFINE: When shooting outdoors on a sunny day.  
ECLOUD: When shooting outdoors on a cloudy day.  
FHALOGEN: When a video light or similar type of lighting is  
used.  
[AUTO]: The shutter speed is adjusted automatically.  
1/2 to 1/4000 (For !mode)/  
SHUTTER SPEED  
A fast shutter speed can  
freeze the motion of a  
fast-moving subject, and  
a slow shutter speed can  
blur the subject to give the  
impression of motion.  
1/2 to 1/500 (For #mode): The smaller the value, the faster the  
shutter speed.  
NOTE  
It is recommended to use the tripod (੬ pg. 18) when recording  
with a slow shutter speed.  
6 [WHOLE SCREEN]: Brightness is adjusted automatically for  
whole screen.  
7 SPOT: Brightness for the specified spot is adjusted  
automatically. Furthermore, brightness in the specified spot  
can be locked by selecting [LOCK]. The Cindicator appears.  
LTo cancel spot exposure control  
Select [WHOLE SCREEN] again so that the Cindicator  
disappears.  
PHOTOMETRY AREA  
Enables you to adjust the  
brightness in the desired  
spot when backlight  
compensation does not  
work well.  
[OFF]: No effect is used.  
1
JSEPIA: The image has a brownish tint like old photos.  
KMONOTONE: The image becomes black and white like old  
movies.  
EFFECT  
Enables you to record  
videos or still images with  
special effects.  
LCLASSIC FILM*: This effect skips frames to give images of an  
old movie atmosphere.  
MSTROBE*: The image looks like a series of consecutive  
snapshots.  
* Not available in #mode.  
TELE MACRO  
Enables you to shoot  
a subject as large as  
possible at a distance of  
approx. 40 cm (1.32 ft)*1 or  
50 cm (1.64 ft)*2.  
[OFF]: Disables the function.  
tON: Activates the function.  
1
*1 GZ-MG467  
*2 GZ-MG360/335/330  
26  
Playing Back Files  
3
Select the desired file.  
Video/Still Image Playback  
1
2
Slide the mode switch to select !  
(video) or #(still image) mode.  
LTo watch on TV  
See page 31.  
LTo check the file information  
Press the INFO button when playback is  
paused. (੬ pg. 33)  
Press the SELECT PLAY/REC button  
to select playback mode.  
LTo adjust the sound volume of videos  
SELECT  
PLAY/REC  
Turn down the  
volume  
Turn up the  
volume  
The index screen for videos appears.  
LOperations during Video Playback  
LOperations during Still Image  
Playback  
: Return to the first scene of the file  
: Go to the first scene of the next file  
: Return to the index screen  
N
O
L
J
E
!
#
$
%
: Rotate 90 degrees counterclockwise  
: Change playback order of slide show  
in reverse direction  
: Rotate 90 degrees clockwise  
: Change playback order of slide show  
(
!
#
P
: Reverse search (during playback)  
: Frame-by-frame playback in reverse  
)
direction (during pause)*  
: Playback  
F
F
Q
K
G
&
(
in forward direction  
: Pause  
: Return to the index screen  
: Display the previous file  
: Start/end the slide show  
: Display the next file  
L
N
F
O
$
%
&
(
: Forward search (during playback)  
: Frame-by-frame playback in forward  
direction (during pause)*  
* Slow playback starts when you keep  
touching the sensor button under E / G  
for a while.  
27  
Playing Back Files (Continued)  
Event Screen  
!
File Search Function  
You can search the desired file by the event  
You can switch the index screen to the date  
index screen or event screen and search a file  
by the recording date or the event.  
that you registered the file to when recording.  
(੬ pg. 23) After searching by the event, you  
can search by the recording date to narrow  
down the search.  
Date Index Screen  
Preparation:  
You can search the desired file by the  
recording date.  
Slide the mode switch to select !mode.  
Press the SELECT PLAY/REC button to  
select playback mode.  
•
•
Preparation:  
Slide the mode switch to select !or #  
•
mode.  
1
2
Select 4.  
Press the SELECT PLAY/REC button to  
select playback mode.  
•
Select the event.  
1
2
Select ?.  
Select the recording date.  
3
4
Select the recording date.  
To display all the files, select [ALL  
SCENES].  
3
Select the file you want to play back.  
Select the file you want to play back.  
LTo return to the index screen  
Select @.  
LTo quit the screen  
Select [QUIT].  
LTo return to the index screen  
Select @.  
LTo change the event registration of a  
file  
See page 34.  
28  
To Play Back MPG Files  
!
MPG files (demonstration files, etc.) are  
stored in the EXTMOV folder.  
Follow the procedure below to play back the  
MPG files in the EXTMOV folder.  
Preparation:  
Slide the mode switch to select !mode.  
Press the SELECT PLAY/REC button to  
select playback mode.  
•
•
1
2
Touch the MENU button.  
Select [PLAYBACK MPG FILE].  
3
Select the file you want to play back.  
LTo return to the normal file playback  
mode  
Select @.  
LTo quit the screen  
Select [QUIT].  
NOTE  
An MOD file is created in the EXTMOV folder  
when management information is corrupted.  
29  
Playing Back Files (Continued)  
LItems for WIPE/FADER setting  
Playback with Special Effects  
OFADER-WHITE:  
•
•
•
Fades in or out with a white screen.  
PFADER-BLACK:  
Wipe or fader effects  
Add effects at the beginning and end of  
videos. These effects cannot be set for still  
images.  
Playback effects  
Add effects that, for example, alter the color  
tones of images.  
Fades in or out with a black screen.  
QFADER-B.W:  
Fades in to a color screen from a black and  
white screen, or fades out in the opposite  
way.  
RWIPE-CORNER:  
•
•
Wipes in on a black screen from the upper  
right to the lower left corner, or wipes out in  
the opposite way.  
Preparation:  
Slide the mode switch to select !or #  
•
mode.  
SWIPE-WINDOW:  
Press the SELECT PLAY/REC button to  
select playback mode.  
•
Starts in the center of a black screen and  
wipes in toward the corners, or wipes out in  
the opposite way.  
The following screen illustrations are  
examples when setting [EFFECT] to  
[SEPIA].  
TWIPE-SLIDE:  
•
•
Wipes in from right to left, or wipes out in the  
opposite way.  
UWIPE-DOOR:  
1
Touch the MENU button.  
Wipes in as the two halves of a black screen  
which open to the left and right revealing the  
scene, or wipes out in the opposite way.  
VWIPE-SCROLL:  
2
Select [WIPE/FADER] (!mode only)  
•
•
or [EFFECT].  
Wipes in from the bottom to the top of a  
black screen, or wipes out in the opposite  
way.  
WWIPE-SHUTTER:  
Wipes in from the center of a black screen  
toward the top and bottom, or wipes out in  
the opposite way.  
3
Select a desired effect.  
For details on each effect, see the right  
column.  
NOTE  
When the screen fades in or out, the sound  
also fades in or out.  
LItems for EFFECT setting  
JSEPIA:  
•
•
•
The image is given a brownish tint like an  
old photo.  
KMONOTONE:  
The image becomes black and white like  
an old movie.  
4
Select the file you want to play back.  
LCLASSIC FILM*:  
The image is given an old movie  
atmosphere by the effect of skipping  
frames.  
LTo turn off the effect  
Select [OFF] in step 3.  
MSTROBE*:  
•
The image looks like a series of  
consecutive snapshots.  
* Not available in #mode.  
30  
Watching Images on TV  
Preparation:  
Set [SWITCH TO ANALOG I/O] to [OUTPUT]. (Factory-preset = [OUTPUT])* (੬ pg. 63)  
Turn off all units.  
* This does not apply to the GZ-MG360/330 model.  
•
•
AV Jack  
DC Jack  
AV Cable  
To AC Outlet  
AV Input Jack  
AC Adapter  
NOTES  
You can also connect the cables using the Everio dock connectors. The S-Video cable  
(optional) enables even higher playback quality. (੬ pg. 10) When other devices such as a DVD  
•
burner are connected to the Everio dock, turn the power of these devices off.*  
This camera is designed to be used with NTSC-type color television signals. It cannot be used  
with a television of a different standard.  
*GZ-MG360/330 model does not include the Everio dock.  
•
1
Turn on the camera and the TV.  
2
Set the TV to its VIDEO mode.  
3
(Only when connecting the camera to the VCR/DVD recorder)  
Turn on the VCR/DVD recorder, and set it to its AUX input mode.  
4
Start playback on the camera. (੬ pg. 27)  
16:9 TV  
4:3 TV  
LIf the aspect ratio of the image is not correct as  
shown on the right  
Change the settings in [SELECT TV TYPE].  
(੬ pg. 65)  
LTo display the camera’s on-screen display on  
TV  
Set [DISPLAY ON TV] to [ON]. (੬ pg. 65)  
31  
EDITING/PRINTING  
Managing Files  
CAUTION  
Deleting/Protecting the Currently  
Displayed File  
Do not remove the recording medium or  
perform any other operation (such as turning  
off the power) while accessing files. Also,  
be sure to use the provided AC adapter, as  
the data on the recording medium may be  
corrupted if the battery becomes exhausted  
during operation. If the data on the recording  
medium becomes corrupted, format the  
recording medium. (੬ pg. 65)  
After performing steps 1-2  
3
Select [CURRENT].  
Deleting/Protecting Files  
4
When [DELETE?] or [PROTECT?]  
appears, select [YES].  
Protected files cannot be deleted. To delete  
them, release the protection first.  
•
Once files are deleted, they cannot be  
restored. Check files before deleting.  
•
Preparation:  
Slide the mode switch to select !or #  
•
mode.  
You can select the previous or next file by  
selecting { or }.  
Press the SELECT PLAY/REC button to  
select playback mode.  
•
The following screen illustrations are  
examples when performing [DELETE].  
Deleting/Protecting Files  
After performing steps 1-2  
1
Touch the MENU button.  
You can skip directly to the delete menu by  
selecting *.  
3
Select [FILE SELECT].  
2
Select [DELETE] or [PROTECT/  
CANCEL].  
4
Select the desired file.  
The * (deletion) or x(protection) mark  
appears on the file. To select other files,  
repeat this step.  
If you slide the zoom lever towards T,  
the preview screen is displayed. Sliding  
the zoom lever towards W returns to the  
index screen.  
•
•
5
Select [QUIT].  
32  
6
Select [EXECUTE AND QUIT] (when  
performing [DELETE]) or [YES]  
(when performing [PROTECT]).  
Viewing File Information  
Preparation:  
For !mode: Pause the playback.  
Alternatively, select the file on the index  
screen.  
•
For #mode: Play back the still image.  
Alternatively, select the file on the index  
screen.  
•
Press the INFO button.  
Deleting/Protecting All Files  
DIRECT  
BACK UP  
After performing steps 1-2 (੬ pg. 32)  
INFO  
3
Select [DELETE ALL] or [PROTECT  
ALL].  
FILE:  
File name  
•
FOLDER:  
Folder name  
DATE/TIME:  
Date and time of the recording  
•
4
When [DELETE ALL?] or [PROTECT  
ALL?] appears, select [YES].  
•
PB TIME (for video files):  
Playback time (length of the file)  
•
SIZE (for still images):  
Image size (੬ pg. 63)  
•
QUALITY:  
Image quality (੬ pg. 62)  
•
LTo quit the screen  
PROTECT:  
File protection status (੬ pg. 32)  
Select [QUIT].  
•
LTo release protection  
LTo turn off the file information display  
Select the protected file in step 4  
(“Deleting/Protecting Files” ੬ pg. 32).  
Press the INFO button again.  
LTo release protection of all files  
1) In step 3, select [CANCEL ALL].  
2) Select [YES].  
33  
Managing Files (Continued)  
Changing the Event of the Selected  
Files  
Changing the Event Registration  
of Video Files after Recording  
!
After performing steps 1-2  
Preparation:  
Slide the mode switch to select !mode.  
Press the SELECT PLAY/REC button to  
select playback mode.  
•
•
3
Select [FILE SELECT].  
4
Select the file you want to register.  
1
2
Touch the MENU button.  
Select [CHANGE EVENT REG.].  
When you select a file, the color of the  
•
cursor changes. To select other files,  
move the cursor forward.You can only  
select the files in order.  
If you slide the zoom lever towards T,  
•
the preview screen is displayed. Sliding  
the zoom lever towards W returns to the  
index screen.  
Changing the Event of the Currently  
Displayed File  
5
Select a new event you want to  
3
4
Select [CURRENT].  
register the file to.  
To select a different destination, select  
[SORT].  
•
To cancel the event registration, select  
[CANCEL].  
•
Select the file you want to register.  
LTo quit the screen  
Select [QUIT].  
You can select the previous or next file by  
selecting { or }.  
34  
5
Select the file you want to copy.  
Partial Delete (EDITED COPY)  
!
You can divide the selected video file into two,  
and make a copy of the desired section as a  
new video file.  
Preparation:  
[COPY 1st SECTION]:  
Copy the section before the division  
point.  
[COPY 2nd SECTION]:  
Copy the section after the division point.  
Slide the mode switch to select !mode.  
•
•
Press the SELECT PLAY/REC button to  
•
select playback mode.  
•
1
Touch the MENU button.  
When copying is finished, the copied file is  
added to the index screen.  
2
Select [EDITED COPY].  
LTo quit the screen  
Select [QUIT].  
NOTE  
When playing back the copied file, the  
recording date of the original file is displayed.  
Meanwhile, the date when you copied is  
displayed on the file information display.  
(੬ pg. 33)  
3
Select the desired file.  
Playback starts.  
4
Set the point at which you want to  
divide the file.  
35  
Playlists  
!
It is a list that enables you to organize  
recorded videos in order of preference.  
5
6
Select the file to add to playlist.  
Preparation:  
Slide the mode switch to select !mode.  
Press the SELECT PLAY/REC button to  
select playback mode.  
•
•
To preview scenes, select the file and  
select [CHECK]. When the index screen of  
individual scenes appears, select the file,  
then touch the OK button.  
Creating Playlists  
1
2
Touch the MENU button.  
Select [EDIT PLAYLIST].  
To return to the previous screen, select @.  
Select the insertion point.  
To add other files, repeat steps 5 and 6.  
•
To delete a registered scene, select the  
3
4
•
Select [NEW LIST].  
registered file, then select [CANCEL].  
7
8
Select } and then [SAVE].  
Select [SAVE AND QUIT].  
Select an item and display files.  
[CREATE BY DATE]:  
Display all the files in the medium listed  
by recording date.  
•
[CREATE BY EVENT]:  
•
Search for an event and display the  
corresponding files listed by recording  
date.  
LTo quit the screen  
Select [QUIT].  
[SELCECT FROM SCENES]:  
Display all files individually.  
NOTES  
•
A maximum of 99 playlists can be created.  
Each playlist can consist of a maximum of  
•
•
99 scenes.  
If you delete the original files, the  
corresponding files are also deleted from  
the playlist.  
•
36  
Creating Playlists including Titles  
Playing Back Playlists  
You can easily create a playlist including a  
title.  
1
2
Touch the MENU button.  
1
Press the TITLE button.  
Select [PLAYBACK PLAYLIST].  
DIRECT  
DVD  
TITLE  
2
Select [NEXT].  
3
Select the playlist you want to play  
back.  
3
Select the desired file.  
LTo stop playback  
Select L.  
LTo quit the screen  
Select [QUIT].  
You can check the scene by selecting  
[CHECK].  
LTo play back from the desired scene  
1) In step 3, select [CHECK]. (The index  
screen for playlist appears.)  
4
Select the desired title.  
2) Select the desired scene.  
NOTE  
When playing back a playlist with a picture  
title, playback starts after the title is displayed  
for 5 seconds.  
LTo dub playlists using a VCR/DVD  
recorder (੬ pg. 46)  
Play back playlists by performing the  
following operations.  
1) After performing steps 1-2 shown  
above, select [DUB].  
LTo return to the previous screen  
Select @.  
LTo quit the screen  
Select [QUIT].  
2) Select [YES].  
NOTES  
For playlist without a picture title: A black  
screen is displayed at the first and the last  
scene for 5 seconds.  
•
For playlist with a picture title: The title is  
displayed at the first scene for 10 seconds.  
•
37  
Playlists (Continued)  
!
Deleting Playlist  
Other Operations of Playlists  
You can perform additional editing and delete  
files in a created playlist.  
3
4
Select [DELETE].  
Preparation:  
Perform steps 1-2. (੬ pg. 36)  
Select a playlist you want to delete.  
To delete all playlists at once, select  
[DELETE ALL].  
Adding/Deleting Files in Playlist  
5
When [DELETE PLAYLIST?] appears,  
select [YES].  
3
Select [EDIT].  
4
Select the playlist you want to edit.  
To add or delete files, follow the steps 5 to  
8 in “Creating Playlists”. (੬ pg. 36)  
Adding a Picture Title to Playlist  
3
4
5
Select [SET TITLE].  
Changing Playlist Names  
Select the desired playlist.  
Select the desired picture title.  
3
Select [RENAME PLAYLIST].  
4
Select the desired playlist.  
5
Select the desired letter.  
Repeat this process to complete the  
•
name.  
You can change the character types  
(capital letters, small letters or marks) by  
selecting [A/a/@].  
•
To correct a letter, move the cursor to the  
letter by sliding your finger up and down,  
then select [CLEAR].  
•
6
When [QUIT?] appears, select [SAVE  
AND QUIT].  
38  
Print Setting  
#
5
Select the number of prints. (max. 15  
prints)  
DPOF Print Setting  
This camera is compatible with DPOF (Digital  
Print Order Format).You can set which  
images to be printed and the number of prints  
with this camera. This feature is useful to print  
with a DPOF-compatible printer or take the  
recording medium to a photo lab for printing.  
To set print information for other images,  
repeat steps 4 and 5. (You can set up to  
999 files.)  
LTo quit the screen  
Select [QUIT].  
Preparation:  
LTo cancel the selection  
Slide the mode switch to #mode.  
Press the SELECT PLAY/REC button to  
select playback mode.  
•
Set the number of prints to “00” in step 5.  
•
Setting All Files Together (One Print for  
Each File)  
1
2
Touch the MENU button.  
Select [DPOF].  
After performing steps 1-2 (੬ left column)  
3
Select [SET ALL 1].  
Setting Files Individually  
4
When [SET ALL TO 1?] appears,  
select [YES].  
After performing steps 1-2  
LTo quit the screen  
3
Select [SET PRINT QUANTITY].  
Select [QUIT].  
LTo confirm DPOF settings  
In step 3, select [CHECK QUANTITY].  
If necessary, change the number of  
prints for the desired file by following  
•
steps 4 and 5.  
LTo reset DPOF settings  
4
Select the desired file.  
1) In step 3, select [RESET].  
2) When [RESET?] appears, select [YES].  
If you slide and hold the zoom lever  
towards T, the preview screen of the still  
image is displayed.  
39  
Print Setting (Continued)  
#
To Print by Selecting a Still Image  
Direct Printing with PictBridge  
Printer  
After performing steps 1-2 (੬ left column)  
If your printer is compatible with PictBridge,  
still images can be printed easily by  
connecting the camera directly to the printer  
with the USB cable. DPOF setting can also be  
used. (੬ pg. 39)  
3
Select [SELECTED PRINT].  
Preparation:  
Close the LCD monitor to turn off the camera.  
4
DC Jack  
USB Jack  
Select the desired image.  
5
Select the desired setting.  
To AC Outlet  
AC Adapter  
USB Cable  
[NUMBER OF PRINTS]:  
The number of prints can be set from 1  
to 99.  
•
PictBridge  
Printer  
[DATE]:  
•
Set whether to print the date and time.  
6
Select [PRINT].  
USB Jack  
LTo stop printing after printing starts  
1) Select [STOP].  
You can also connect the cables using the  
jacks on the Everio dock. (੬ pg. 10)*  
* GZ-MG360/330 model does not include the  
Everio dock.  
2) When [QUIT PRINTING?] appears,  
select [YES].  
1
Open the LCD monitor to turn on the  
camera.  
2
Select [DIRECT PRINT].  
40  
To Print Using the DPOF Settings  
If the printer is compatible with DPOF, you  
can use the DPOF settings. (੬ pg. 39)  
After performing steps 1-2 (੬ pg. 40)  
3
Select [DPOF PRINT].  
4
Select [PRINT].  
LTo stop printing after printing has  
already started  
1) Select [STOP].  
2) When [QUIT PRINTING?] appears,  
select [YES].  
LTo confirm the DPOF setting  
In step 4, select [CHECK SETTINGS]. To  
return to the previous screen, select @.  
NOTES  
If the printer is not recognized, disconnect  
the USB cable, then reconnect it.  
•
You cannot return to the previous screen  
•
while operating Direct print. If you want to  
redo the operation, remove the USB cable,  
turn the camera off, and start the operation  
again from the beginning.  
41  
COPYING  
Copying Files  
Types of Copying and Connectable Device  
Using a DVD Burner to Copy Files  
from the Camera  
The Camera  
You can copy still images  
from HDD onto microSD  
card or from microSD card  
to HDD with this camera  
alone. (੬ pg. 48)  
Supported discs: 12cm DVD-R, DVD-RW  
Regarding DVD-R discs, only unused DVD-R  
discs can be used. Regarding DVD-RW  
discs, used DVD-RW discs can also be  
used, but they need to be formatted before  
recording. Formatting a disc deletes all  
content recorded on the disc up until that  
time.  
•
•
DVD Burner  
(CU-VD3)  
You can copy video files  
recorded on this camera  
onto DVD discs. (੬ right  
column)  
Dual-layer discs cannot be used.  
Regarding finalization after copying  
The disc is automatically finalized so that  
it can be played on other devices. After  
finalizing, the disc is a play-only disc, so no  
more files can be added.  
VCR/DVD Recorder  
NOTE  
You can dub video files  
recorded on this camera  
onto DVD discs. (੬ pg. 46)  
When using the optional DVD Burner, read its  
instructions.  
Connection with a DVD Burner  
Preparation:  
Close the LCD monitor to turn off the camera.  
PC  
You can copy video/still  
image files on this camera  
onto your PC. (੬ pg. 49  
to 60)  
To AC Outlet  
AC Adapter  
USB Jack  
DC Jack  
USB Jack  
USB Cable  
DVD Burner  
NOTE  
Use the USB cable that came with the DVD  
burner.  
42  
Making a Backup of All Files  
Preparation:  
Copying Video Files that Have Never  
Been Copied  
Connect the camera to the DVD burner.  
Files that have never been copied to the DVD  
discs are automatically selected and copied.  
•
(੬ pg. 42)  
Slide the mode switch to select !mode.  
•
1
Open the LCD monitor to turn on the  
camera.  
The following screen illustrations are  
examples when backing up video files.  
2
Press the DIRECT DVD button.  
1
Select [CREATE TOGETHER].  
DIRECT  
DVD  
TITLE  
3
Select [EXECUTE].  
2
Select the desired menu.  
[ALL SCENES]:  
•
All files in the recording medium are  
copied.  
[UNSAVED SCENES]:  
•
Files that have never been copied to a  
DVD disc are automatically selected and  
copied.  
The DVD disc begins to be created.  
When [COMPLETED] appears, touch  
•
the OK button.  
When [COMPLETED. CHANGE DISC]  
appears, change the disc. The second  
DVD disc begins to be created.  
•
To cancel the DVD creation, select  
[CANCEL].  
•
3
Select the desired menu.  
LTo quit the screen  
The files are copied on the disc. When  
[COMPLETED] appears, touch the OK  
•
1) Select [QUIT].  
2) When [QUIT?] appears, select [YES].  
button.  
When [COMPLETED. CHANGE DISC]  
appears, change the disc. Remaining  
files are copied on the second disc.  
•
To cancel copying, select [STOP].  
•
43  
Copying Files (Continued)  
3
4
Selecting Files for Backup  
Preparation:  
Select the desired disc number.  
If you select [ALL], all discs in the list are  
created.  
•
Connect the camera to the DVD burner.  
(੬ pg. 42)  
•
To preview scenes, select [CHECK].  
•
When the index screen of individual  
scenes appears, select the file, and  
touch the OK button.  
Slide the mode switch to select !mode.  
•
The following screen illustrations are  
examples when backing up video files.  
To return to previous screen, select @.  
mark shows that the disc is created  
•
already.  
1
Select [SELECT AND CREATE].  
Select [EXECUTE].  
A disc begins to be created. When  
[COMPLETED] appears, touch the OK  
•
button.  
When [COMPLETED. CHANGE DISC]  
appears, change the disc. The second  
disc begins to be created.  
•
2
Select the desired menu.  
To cancel the disc creation, select  
[STOP].  
•
LTo quit the screen  
1) Select [EXIT].  
2) When [QUIT?] appears, select [YES].  
[CREATE BY DATE]:  
•
NOTE  
Files are sorted according to the date  
on which they were recorded. Relevant  
files are displayed in a list. Select the  
recording date, and touch the OK button.  
When executing [CREATE BY PLAYLIST],  
date/time on the file information display shows  
the date of copying the file, instead of the  
actual recording date.  
[CREATE BY EVENT]:  
•
Files are sorted according to event.  
Relevant files are displayed in a list.  
Select the event, and touch the OK  
button.  
LTo duplicate a disc  
The last creation date is displayed. (Up to  
20 files)  
1) In step 1 (੬ left column), select  
[CREATE DUPLICATE].  
2) Select the date and touch the OK  
button, then go to step 4.  
[CREATE BY PLAYLIST]:  
•
Files are sorted according to playlist. The  
selected playlists are displayed in a list.  
1) Select the desired list, and touch the  
OK button.  
2) Select the insertion point and select  
}. To select other lists, repeat this  
process.  
LTo check whether the DVD disc was  
created properly  
In step 1 (੬ left column), select  
[PLAYBACK], and touch the OK button.  
[SELECT FROM SCENES]:  
Select files individually.  
•
1) Select the desired file, and touch the  
OK button.  
2) Select the insertion point and select  
}. To select other files, repeat this  
process.  
44  
LTo play back the created disc using the  
camera  
1) Connect the camera to the DVD burner.  
(੬ pg. 42)  
LTitle and chapter of created DVD  
Each recording date becomes one title in  
a created DVD and each file recorded in a  
same day becomes one chapter in the title.  
2) To view the disc on TV, connect the  
camera to TV. (੬ pg. 31)  
3) Turn on the camera.  
Jan. 10. 2007: file 1 and 2 were recorded.  
File 1  
File 2  
4) Select [PLAYBACK].  
Jan. 11. 2007: file 3 and 4 were recorded.  
5) Select the desired folder.  
6) Select the creation date of the disc.  
7) Select the desired file. To return to the  
previous screen, select @.  
File 3  
File 4  
Create a DVD  
Title  
JAN.10.2007  
LDisc number  
JAN.11.2007  
Disc number shows the number of DVD  
discs you can create. The dubbing range  
of each disc is automatically allocated,  
presuming that all the files are to be  
dubbed from the first one on the list. This  
dubbing range cannot be changed.  
E.g.) “DVD1” can contain two files,  
“JAN.01.2007” and “JAN.15.2007”.  
File 1 File 2  
File 3  
File 4  
1
2
3
4
Chapter  
LMenu for disc playback  
When you play back the created DVD  
disc on a DVD player or other devices, the  
following top menu will be displayed.  
!Disc title: Creating date of the disc  
#Disc number (੬ left column)  
$Title thumbnail: First scene of the title  
%Title name: Recording date/Playlist  
name  
45  
Copying Files (Continued)  
Using a VCR/DVD Recorder to Dub  
Files from the Camera  
1
2
Set the VCR/DVD recorder to its AUX  
input mode.  
Preparation:  
Set [SWITCH TO ANALOG I/O] to  
[OUTPUT]. (Factory-preset = [OUTPUT])*  
(੬ pg. 63)  
Start playback on the camera.  
•
To play back videos (੬ pg. 27)  
To play back playlists (“When dubbing  
playlists using a VCR/DVD recorder”  
•
•
Turn off all units.  
•
੬ pg. 37)  
*
This does not apply to the GZ-MG360/330 model.  
3
At the point you want to start  
dubbing, start recording on the VCR/  
DVD recorder.  
Refer to the VCR/DVD recorder’s  
instruction manual.  
AV Jack  
DC Jack  
LTo stop dubbing  
Stop recording on the VCR/DVD recorder,  
then press the START/STOP button again.  
NOTE  
AC Adapter  
To AC  
To record only the date information among the  
display indications, set [DISPLAY ON TV] to  
[ON], and touch the OK button until date/time  
indication appears. (੬ pg. 65)  
Outlet  
AV Cable  
VCR/DVD Recorder  
AV Input Jack  
You can also connect the cables using the  
jacks on the Everio dock connectors. The  
S-Video or DV cable (optional) enables even  
higher dubbing quality. (੬ pg. 10) When other  
devices such as a DVD burner are connected  
to the Everio dock, turn the power of these  
devices off.*  
* GZ-MG360/330 model does not include the  
Everio dock.  
46  
Using the Camera to Dub Files from  
a VCR/DVD Player  
1
2
Start playback on the VCR/DVD  
player.  
Preparation:  
Set [SWITCH TO ANALOG I/O] to [I/O]*.  
(੬ pg. 63)  
Turn off all units.  
Press the START/STOP button on the  
camera at the scene where you want  
to start recording.  
•
•
*
This does not apply to the GZ-MG360/330 model.  
LTo stop recording  
Press the START/STOP button again.  
AV Jack  
DC Jack  
NOTES  
If “COPY PROTECTED CONTENT”  
appears, the file is protected and cannot be  
recorded.  
•
If the videos you want to record contain both  
•
16:9 and 4:3 screen size, recording stops  
where the aspect ratio switches. To record  
such videos, you need to perform recording  
operation at every switching point.  
AC Adapter  
To AC  
Outlet  
AV Cable  
VCR/DVD Player  
AV Output Jack  
You can also connect the cables using the  
jacks on the Everio dock connectors. The  
S-Video cable (optional) enables even higher  
quality dubbing. (੬ pg. 10) When other  
devices such as a DVD burner are connected  
to the Everio dock, turn the power of these  
devices off.*  
* GZ-MG360/330 model does not include the  
Everio dock.  
47  
Copying Files (Continued)  
5
Select [EXECUTE].  
Copying/Moving Files  
File transfer starts. When [COPYING/  
MOVING COMPLETED] appears, touch  
the OK button.  
You can copy or move files in the HDD and  
microSD card using the on-screen display.  
Preparation:  
LTo quit the screen  
Slide the mode switch to select !or #  
•
•
•
•
Select [QUIT].  
mode.  
Press the SELECT PLAY/REC button to  
select playback mode.  
LTo stop the file transfer  
1) Select [STOP].  
2) When [QUIT?] appears, select [YES].  
Make sure that microSD card is inserted in  
the microSD slot.  
Make sure that enough free space is left in  
the copy/move destination medium.  
1
2
Touch the MENU button.  
Select [COPY] or [MOVE].  
[COPY]:  
•
Files are copied to the destination  
medium while leaving original files in the  
source medium.  
[MOVE]:  
•
Files are moved to the destination  
medium while deleting original files  
(except read-only files) in the source  
medium.  
3
4
Set the direction of copy/move by  
selecting [UPDATE]. (HDD } SD or  
SD } HDD)  
Set the file unit ([ALL] or [FILE]) to  
copy/move by selecting [SELECT].  
[FILE]:  
•
Select when you want to transfer the  
selected files.  
1) Select the desired file, and touch the  
OK button.  
The smark appears on the file. To  
•
select other files, repeat this step.  
2) Select @.  
[ALL]:  
•
Select when you want to transfer all files  
in the recording medium.  
48  
PC OPERATION  
File Backup on a Windows® PC  
Install the software that came with the camera  
to your PC.  
For the compatible DVD burners, refer to  
CyberLink web site:  
http://www.cyberlink.com/english/products/  
powerproducer/3/comp_dvd_drives.jsp  
You can back up your files on your PC with a  
simple one-touch operation, edit your files on  
your PC, and also create discs.  
Even if you do not install the software, you  
can still back up your files on your PC.  
(੬ pg. 53)  
NOTE  
The system requirements information is not  
a guarantee that the provided software will  
work on all personal computers meeting those  
requirements.  
System Requirements  
OS:  
Either one of the following OS should be pre-  
installed (32-bit):  
Windows® XP Home Edition (SP2), Windows®  
XP Professional (SP2), Windows VistaTM  
Home Basic, Windows VistaTM Home Premium  
CPU:  
Intel® Pentium® 4, at least 1.6 GHz  
(at least 2.2 GHz recommended)  
Intel® Pentium® M, at least 1.4 GHz  
Intel® CoreTM Duo, at least 1.5 GHz  
RAM:  
[XP] At least 256 MB (For creating DVD Video  
by PowerCinema (੬ pg. 55), 1 GB or more)  
[Vista] At least 1 GB (2 GB or more  
recommended)  
Free hard disk space:  
At least 550 MB for installation  
For creating DVD Video, at least 10 GB  
recommended  
For creating VCD, at least 1 GB  
recommended  
USB port:  
USB 2.0 port  
Display:  
Must be capable of displaying at least  
1024 x 768 (XGA) in high color 16 bit or higher  
(1280 x 1024 (SXGA) or higher is recommended)  
Miscellaneous:  
Internet Explorer 5.5 or later  
DirectX 9.0 or later  
Supported media:  
DVD-Video: DVD-R/-RW, DVD+R/+RW  
DVD-VR: DVD-RW, DVD-RAM  
DVD+VR: DVD+RW  
VideoCD: CD-R/RW  
49  
File Backup on a Windows® PC (Continued)  
Preparation:  
Quit any other software you are using. (Check  
Software Installation  
that there are no other application icons on  
the status bar.)  
The following software is included in the CD-  
ROM that came with your camera.  
CyberLink DVD Solution  
•
1
Load the provided CD-ROM into the  
Comprehensive application software that  
consists of the following three kinds of  
software.  
PC.  
After a moment, the [SETUP] screen  
appears. If the [SETUP] screen does not  
appear, double-click the CD-ROM icon in  
[My Computer].  
PowerCinema NE for Everio  
The main file managing software.You can  
perform various operations such as file  
backup, playback, and DVD authoring.  
2
Click [Easy Installation].  
If you want to specify the type of software  
to install or the installation destination  
folder etc., select [Custom Installation].  
Follow the instructions on the screen to  
install the software.  
QYou can perform detailed settings for each  
item.  
RSelect a function on the right, and the  
explanation of function is displayed.  
SDisplays operating procedure for each function.  
(internet connection is required)  
TPlays back video files on the PC (੬ pg. 54)  
UPlays back still image files on the PC  
(੬ pg. 54)  
3
Click [Yes].  
VCopies/edits files on the PC  
WBurns file that are backed up on the PC onto a  
DVD  
XCreates a DVD-Video (੬ pg. 54)  
YBacks up camera files onto the PC (੬ pg. 52)  
PowerProducer 3 NE  
Allows you to create discs. Automatically  
starts from an operation in PowerCinema  
NE for Everio.  
PowerDirector 5 NE Express  
Allows you to edit files on your PC.  
Automatically starts from an operation in  
PowerCinema NE for Everio.  
4
Select the desired language and  
click [OK].  
Digital Photo Navigator 1.5  
Allows you to change the format of still  
image files backed up on your PC.  
•
You can find the latest information on the  
provided software program at CyberLink’s  
world wide web server at http://www2.cli.  
co.jp/products/ne/  
50  
5
6
Click [Yes].  
The software installation starts.  
Connecting the Camera to the PC  
Preparation:  
Close the LCD monitor to turn off the camera.  
DC Jack  
USB Jack  
Click [Finish].  
USB Cable  
AC Adapter  
LWhen installation is completed  
The installed software is displayed in [All  
Programs].  
To AC Outlet  
USB Port  
NOTES  
Never disconnect the USB cable while the  
access/charge lamp on the camera lights or  
blinks.  
Do not turn off the camera when the USB  
cable is connected, to prevent malfunctions  
of the PC.  
•
The backup destination folder [MyWorks]  
for files is created on the hard disk drive  
that has the most free space.  
•
Connect the camera directly to the USB jack  
on the PC, not through a hub.  
•
Do not use an extension USB cable.  
Saving the wrong kinds of files in a  
•
•
recording medium or deleting files or  
folders from a recording medium can cause  
problems with the operation of the camera.  
When it is necessary to delete a file from  
a recording medium, delete it through the  
camera. Also, do not move or rename  
folders and files in the medium on PC.  
51  
File Backup on a Windows® PC (Continued)  
LWhen you have finished operation  
1
Open the LCD monitor to turn on the  
Always follow the procedures below when  
disconnecting the camera, or turning off  
the power of the camera/PC.  
camera.  
2
On the camera, press the DIRECT  
BACK UP button.  
Failing to do so may cause damage to the  
camera and PC.  
1) Confirm that the access/charge lamp on  
the camera does not light or blink. (If the  
access/charge lamp lights or blinks, wait  
until it is turned off before proceeding.)  
2) Double-click the [Safely Remove  
Hardware] or [Unplug or Eject  
Although a dialog box appears on the PC,  
you do not need to use it. File copy starts  
automatically.  
Hardware] icon in the status bar.  
3) Select [USB Mass Storage Device] or  
[USB Disk], and then click [Stop].  
4) Click [OK].  
5) Disconnect the USB cable.  
6) Turn off the camera and PC.  
When the progress bar disappears, the  
process is complete.  
File Backup on the PC  
NOTE  
This method uses the software on the  
provided CD-ROM to back up files onto your  
PC.  
When backup is performed, folders for each  
medium (HDD or microSD) are created in the  
[MyWorks] folder (੬ pg. 51), and the files are  
backed up inside those folders. (If backup is  
performed from more than one camera HDD,  
individual HDD folders are created.)  
Video files that have never been backed up  
onto the connected PC are automatically  
selected from the back up history and backed  
up.  
If you could not install the software, turn to  
page 53 for details of how to back up your  
files without using this software.  
File Backup from a Specified Media  
Preparation:  
Preparation:  
Install the software from the provided CD-  
ROM. (੬ pg. 50)  
•
Install the software from the provided CD-  
ROM. (੬ pg. 50)  
•
Connect the camera to the PC with the USB  
cable. (੬ pg. 51)  
•
Connect the camera to the PC with the USB  
cable. (੬ pg. 51)  
•
1
Open the LCD monitor to turn on the  
camera.  
2
On the camera, select [BACK UP].  
52  
3
5
Click [EVERIO_HDD] or [EVERIO_  
SD].  
When the progress bar disappears, the  
process is complete.  
Select the folder you want to back  
up, and drag & drop it into the folder  
you created in step 1.  
SD_VIDEO:  
•
Folder that contains video files. If you  
want to back up files individually, open  
this folder, and drag & drop files such as  
[PRG001] one by one.  
DCIM:  
•
Folder that contains still image files. If  
you want to back up files individually,  
open this folder, and drag & drop files  
such as [PIC_0001.JPG] one by one.  
File Backup on the PC without Using  
Software  
Preparation:  
Connect the camera to the PC with the USB  
cable. (੬ pg. 51)  
1
On the PC, create a folder to back up  
files into.  
NOTE  
For further details on the use of folders, see  
page 60.  
2
Open the LCD monitor to turn on the  
camera.  
3
On the camera, select [PLAYBACK  
ON PC].  
4
Double-click [EVERIO_HDD] or  
[EVERIO_SD] icon.  
53  
Other Windows® PC Operations  
5
Click the desired file.  
Playing Back Files on the PC  
Preparation:  
Install the software from the provided CD-  
ROM. (੬ pg. 50)  
•
Connect the camera to the PC with the USB  
cable. (੬ pg. 51)  
•
1
Open the LCD monitor to turn on the  
camera.  
If you click Sort by/Filter by/View by,  
searching options are displayed. Use them  
to search a file quickly.  
2
On the camera, select [PLAYBACK  
ON PC].  
Sort by:  
The order of files is rearranged  
•
Although a dialog box appears on the PC,  
you do not need to use it. PowerCinema  
starts automatically.  
according to item that you selected.  
Filter by:  
Files are filtered according to the item  
that you selected.  
•
3
Click [Browse Videos] (for video  
playback) or [Browse Pictures] (for  
still image playback).  
View by:  
You can change the number of  
thumbnails on a screen.  
•
For more information on detailed operations  
of the software, see the Tutorials (੬ pg. 56)  
or CyberLink web site (੬ pg. 50).  
4
Click the media that contains the  
desired files.  
54  
Selecting Files for Backup  
Creating a DVD-Video  
Preparation:  
1
2
On the camera, select [CREATE  
DVD].  
Although a dialog box appears on the PC,  
you do not need to use it. PowerCinema  
starts automatically.  
Install the software from the included CD-  
ROM. (੬ pg. 50)  
•
Connect the camera to the PC with the USB  
cable. (੬ pg. 51)  
•
Open the LCD monitor to turn on the  
camera.  
•
On the PC, click the check box of the  
desired file.  
Copying Video Files that Have Never  
Been Copied  
The smark appears on the left of the  
selected file.  
1
On the camera, press the DIRECT  
DVD button.  
To select other files, repeat this step.  
Although a dialog box appears on the PC,  
you do not need to use it. PowerCinema  
starts automatically.  
2
On the PC, authoring and burning  
starts.  
Click [Stop] to cancel the procedure.  
3
4
Click [Author and Burn].  
Click [Burn to Disc].  
Authoring and burning starts.  
Click [Stop] to cancel the procedure.  
3
Click [OK].  
Continued on Next page  
55  
Other Windows® PC Operations (Continued)  
5
Click [OK].  
For more information on detailed  
operations of the software, see the  
Tutorials (੬ pg. 56) or CyberLink web site  
(੬ pg. 50).  
NOTES  
You can use following discs:  
- DVD-R/DVD+R (Unused discs)  
•
- DVD-RW/DVD+RW (They need to be  
formatted before recording. Formatting  
deletes all content recorded on the disc.)  
DVD-RAM discs cannot be used.  
You may not be able to play back the  
created disc depending on the performance  
of the device. Also, the image may stop  
momentarily at junctions between scenes.  
•
•
The PC must be equipped with a compatible  
drive and player software to play back the  
created disc.  
•
56  
Digital Photo Navigator 1.5  
Getting More Use of the Software  
The User’s Guide is included on the CD-ROM  
in PDF format.  
For more information on operations of the  
software, see the Tutorials for each software  
program or the User’s Guides.  
1
Load the provided CD-ROM into the  
PC.  
PowerCinema NE for Everio  
2
Right-click the CD-ROM icon in [MY  
1
Computer], then click [Open].  
Double-click the PowerCinema NE  
for Everio icon.  
Start PowerCinema NE for Everio.  
3
Double-click the [DOCS] folder.  
2
Click [Tutorial].  
4
Open the “Start.pdf” file and click the  
button of the desired language.  
PowerProducer 3 NE  
NOTES  
You need to connect to the Internet to see  
•
the Tutorial.  
Adobe® Acrobat® ReaderTM or Adobe®  
1
Click [Start], go to [All Programs],  
select [CyberLink PowerProducer].  
•
Reader® must be installed to read PDF  
files. Adobe® Reader® can be loaded from  
Adobe’s web site: http://www.adobe.com/  
2
Click [PowerProducer User’s Guide]  
or [Readme].  
PowerDirector 5 NE Express  
1
Click [Start], go to [All Programs],  
select [Cyber Link PowerDirector  
Express].  
2
Click [PowerDirector Express User’s  
Guide] or [Readme].  
57  
File Backup on a Macintosh®  
You can back up camera files onto your  
computer.  
When you copy files from the computer to  
•
the recording medium on the camera, do not  
include any other files than those recorded  
with the camera.  
Do not delete, move, or rename the files and  
folders in the camera from the computer.  
System Requirements  
•
Hardware:  
Macintosh must be standard equipped with  
USB 2.0 port  
OS:  
LWhen you have finished operation  
Always follow the procedures below when  
disconnecting the camera, or turning the  
power of the camera/computer off.  
Failing to do so may cause damage to the  
camera and computer off.  
1) Drag & drop the recording medium icon  
on the desktop into the [Trash] icon.  
If the confirmation message appears,  
click [OK].  
2) Confirm that the access/charge lamp on  
the camera does not light or blink.  
If the access/charge lamp lights or  
blinks, wait until it is turned off before  
proceeding.  
Mac OS X (v10.3.9, v10.4.2 to v10.4.10)  
Connecting the Camera to the  
Macintosh  
Preparation:  
Close the LCD monitor to turn off the camera.  
3) Disconnect the USB cable.  
4) Turn off the camera and computer.  
DC Jack  
USB Jack  
USB Cable  
AC Adapter  
To AC Outlet  
USB Port  
NOTES  
Never disconnect the USB cable while the  
access/charge lamp on the camera lights or  
blinks.  
•
Do not turn off the camera when the USB  
cable is connected, to prevent malfunctions  
of the PC.  
•
Connect the camera directly to the  
computer, not through a hub.  
Do not use an extension USB cable.  
•
•
58  
DCIM:  
•
File Backup on the Macintosh  
Folder that contains still image files. If  
you want to back up files individually,  
open this folder, and drag & drop files  
such as [PIC_0001.JPG] one by one.  
Preparation:  
Connect the camera to the computer with the  
USB cable. (੬ pg. 58)  
1
On the computer, create a folder to  
back up files into.  
2
Open the LCD monitor to turn on the  
camera.  
3
On the camera, select [PLAYBACK  
ON PC].  
NOTE  
4
Double-click [EVERIO_HDD] or  
[EVERIO_SD] icon.  
For further details on the use of folders, see  
page 60.  
5
Select the folder you want to back  
up, and drag & drop it into the folder  
you created in step 1.  
SD_VIDEO:  
•
Folder that contains video files. If you  
want to back up files individually, open  
this folder, and drag & drop files such as  
[PRG001] one by one.  
59  
Folder Structure and Extensions  
Recording medium  
X = number  
[DCIM]  
Contains the still image folders.  
[XXXJVCSO]  
[XXXJVCSO]  
[XXXJVCSO]  
[SD_VIDEO]  
[MGR_INFO]  
[PRGXXX]  
[PRGXXX.PGI]  
Contains the video file folders.  
Management information* for the media as a  
whole  
Management information*  
Video file  
Management information* for the video files  
[MOVXXX.MOD]  
[MOVXXX.MOI]  
[PRGXXX]  
[PRGXXX]  
[EXTMOV]  
Video file which management information is  
corrupted.  
[MOV_XXX.MOD]  
[DEM_XXX.MPG]  
Demo video file  
[MISC]  
[PRIVATE]  
Contains folders with DPOF setting data.  
Contains management information files of event  
and/or DVD creation information for the files taken  
with the camera.  
* Information such as the date and time of recording, recorded with the video file.  
Extensions  
Video files  
Still image files  
: “.MOD”  
: “.jpg”  
For Windows®, the file extension may not appear depending on the [FOLDER] option setting.  
60  
Customer Support Information  
Contact us for Information on the Provided Software  
Use of this software is authorized according to the terms of the software license.  
JVC  
When contacting the nearest JVC office or agency in your country (refer to the JVC Worldwide  
Service Network at http://www.jvc-victor.co.jp/english/worldmap/index-e.html) about this  
software, please have the following information ready.  
Product Name  
Model  
Problem  
PC  
•
•
•
•
•
Manufacturer  
Model (Desktop/Laptop)  
CPU  
OS  
Error Message  
Memory (MB)  
Available Hard Disk Space (GB)  
Please note that it may take some time to respond to your questions, depending on their subject  
matter.  
JVC cannot answer questions regarding basic operation of your PC, or questions regarding  
specifications or performance of the OS, other applications or drivers.  
CyberLink  
Telephone/fax support  
Office hours  
(Mon. to Fri.)  
Location  
Language  
Phone #  
Fax #  
English / German /  
French / Spanish /  
Italian  
9:00 am to  
5:00 pm  
Germany  
+49-700-462-92375 +49-241-70525-25  
9:00 am to  
6:00 pm  
+886-2-8667-1298  
+886-2-8667-1300  
ext. 333  
Taiwan  
Japan  
Mandarin  
Japanese  
10:00 am to  
5:00 pm  
+81-3-3516-9555  
–
Paid voice support  
Lines are open  
(Mon. to Fri.)  
Location  
Language  
English  
URL  
1:00 pm to  
10:00 pm CST  
http://www.cyberlink.com/english/cs/  
support/new_site/voice_support.jsp  
U.S.A.  
Support web/e-mail  
Language  
URL/e-mail address  
English  
http://www.cyberlink.com/english/cs/support/new_site/support_index.html  
[email protected]  
German / French /  
Spanish / Italian  
Japanese  
http://jp.cyberlink.com/support/  
61  
MENU SETTINGS  
Changing the Menu Settings  
E.g.) Set [DROP DETECTION] to [OFF].  
3
Select the desired setting.  
For details on each menu, see below.  
1
2
Touch the MENU button.  
Select the desired menu.  
LTo return to the previous screen  
Select @.  
LTo quit the screen  
Select [QUIT].  
Menus  
Settings: [ ] = Factory-preset  
[OFF] / 2SEC / 10SEC  
NOTES  
zSELF-TIMER  
Starts recording when the set time  
elapses after the SNAPSHOT button  
is pressed.  
You can confirm the countdown on the camera screen.  
You can also use this to prevent vibration by the hand.  
•
•
[RECORD ONE SHOT]: Records one still image at a  
time.  
CONTINUOUS SHOOTING: Records still images  
continuously while the SNAPSHOT button is  
pressed.  
8 SHUTTER MODE  
NOTES  
The interval between recording still images is approx. 0.3  
•
seconds.  
Continuous shooting may not work well depending on the  
•
recording medium.  
The continuous shooting speed will drop if this function is  
•
used repeatedly.  
nVIDEO QUALITY  
Enables you to set the picture quality  
for videos.  
ULTRA FINE / [FINE] / NORMAL / ECONOMY  
nIMAGE QUALITY  
Enables you to set the picture quality  
for still images.  
[FINE] / STANDARD  
[GZ-MG467]  
yIMAGE SIZE  
[1152 x 864] / 640 x 480  
Selects the picture size for still images.  
pGAIN UP  
Makes the subject appear bright  
automatically when you record in dark  
places. However, the overall color  
tones appear grayish.  
OFF: Disables the function.  
[ON]: Activates the function.  
62  
Menus  
Settings: [ ] = Factory-preset  
4:3: Records videos in 4:3 size.  
[16:9]: Records videos in 16:9 size. The 16:9 indicator  
lights up on the LCD monitor.  
NOTES  
If the [VIDEO QUALITY] is set to [ECONOMY], you  
•
cannot record in 16:9 size (the 16:9 indicator lights up  
!SELECT ASPECT RATIO  
Enable you to select the aspect ratio  
for videos.  
blue).  
If you want to copy the recorded videos onto DVD discs,  
•
it is recommended not to mix 16:9 size videos and 4:3  
size videos.  
If you record videos in 16:9 size, the aspect ratio of the  
•
video may be incorrect when watching the videos on TV.  
If this occurs, change the settings in [SELECT TV TYPE].  
(੬ pg. 65)  
[GZ-MG467]  
32X / [64X] / 800X  
NOTE  
Optical zoom is used up to 32X. Digital zoom is used from  
more than 32X up to the selected zoom ratio.  
@ZOOM  
Enables you to set the maximum zoom  
ratio.  
[GZ-MG360/335/330]  
35X / [70X] / 800X  
NOTE  
Optical zoom is used up to 35X. Digital zoom is used from  
more than 35X up to the selected zoom ratio.  
OFF: Disables the function.  
[ON]: Activates the function.  
NOTES  
qDIS  
Accurate stabilization may not be possible if hand shake  
is excessive, or depending on the shooting conditions.  
•
Compensates for hand shake.  
Set this mode to [OFF] when recording with the camera  
on a tripod.  
•
[OFF]: Disables the function.  
ON: Activates the function.  
oWIND CUT  
Reduces noise caused by wind.  
[GZ-MG467/335]  
[OUTPUT]: Switches to output.  
I/O: Switches to input. The Aindicator lights up on the  
LCD monitor.  
ASWITCH TO ANALOG I/O  
Switches input and output for the  
AV/S-Video jack of the camera.  
+ MONITOR OFF*1 *2  
YES: Turn off the backlight. (no display)  
NO: Turn on the backlight.  
NOTE  
Enables you to turn off the backlight  
on the monitor temporarily.  
*1 Playback mode only.  
*2 When [MONITOR OFF] in the playback  
menu is activated, use the remote  
control to play back files.  
To turn on the backlight again, perform any operation such  
as zooming.  
63  
Changing the Menu Settings (Continued)  
Settings: [ ] = Factory-preset  
Menus  
BASIC SETTINGS  
Select [BASIC SETTINGS], then select sub-menus.  
OFF: Disables the function.  
[ON]: Activates the function.  
NOTES  
&QUICK RESTART  
Enables the camera to start up  
quickly when you turn the power  
off and then on again within five  
minutes by closing and opening  
the LCD monitor. (“Power-linked  
operation” ੬ pg. 12)  
This function is not available during charging.  
•
You can reset the setting by pressing and holding the  
•
power button.  
Access/charge lamp blinks when this function is activated  
•
and the camera is turned off.  
B MONITOR BRIGHT  
Enables you to set the brightness  
of the LCD monitor.  
Adjust the brightness of the display by using the touch  
sensor.  
BRIGHTER / STANDARD / [AUTO]  
NOTE  
C MONITOR BACKLIGHT  
Enables you to adjust the  
brightness of backlight on the  
monitor.  
When you select [AUTO], the brightness will automatically  
be set to [BRIGHTER] when you use the camera outdoors  
and to [STANDARD] when you use the camera indoors.  
/REC MEDIA FOR VIDEO  
Enables you to set the recording  
medium for videos.  
[HDD] / SD  
3REC MEDIA FOR IMAGE  
Enables you to set the recording  
medium for still images.  
[HDD] / SD  
DATE STYLE:  
year.month.day / [month.day.year] / day.month.year  
TIME:  
24h / [12h]  
;DATE DISPLAY STYLE  
Enables you to set the date and  
time display format.  
9LANGUAGE  
You have a choice of 7 languages. (੬ pg. 72) The  
default language is [ENGLISH].  
Enables you to set the display  
language. (੬ pg. 17)  
OFF: Disables the function.  
[ON]: Activates the function.  
^DROP DETECTION  
To turn the unit on when the drop detection worked,  
close the LCD monitor and open it again.  
NOTE  
Prevents damage to the HDD by  
turning off the power automatically  
when the camera detects that it has  
been dropped.  
Setting this function to off increases the risk of damaging  
the built-in hard disk if the camera is accidentally dropped.  
]REMOTE  
OFF: Disables operation with the remote control.  
[ON]: Enables operation with the remote control.  
Turns reception of the operation  
signal from the remote control  
on/off.  
OFF: Disables the function.  
[ON]: Activates the function.  
NOTES  
[DEMO MODE  
Introduces special features of the  
camera at the following cases.  
When the menu screen is closed.  
When there is no operation for  
•
The demonstration only works when the DC cord is  
•
•
connected, not with the battery.  
about 3 minutes during recording  
mode.  
If a microSD card is in the camera, demonstration will not  
take place even if the power is on.  
•
64  
Settings: [ ] = Factory-preset  
Menus  
BASIC SETTINGS  
Select [BASIC SETTINGS], then select sub-menus.  
OFF: Turns off the operation sound.  
[ON]: The melody sounds when any operation is  
performed.  
\OPERATION SOUND  
Turns the operation sound on/off.  
#SELECT TV TYPE  
Enables you to select the TV type  
when watching files recorded on  
the camera on TV.  
4:3 TV / [16:9 TV]  
OFF: Disables the function.  
[ON]: Activates the function.  
(AUTO POWER OFF  
If the camera is not operated for  
5 minutes while the power is on,  
it turns itself off automatically to  
conserve power.  
To turn the camera on again, close the LCD  
monitor and open it again when using the battery  
pack. When using the AC adapter, perform any  
operation such as zooming.  
[OFF]: Does not display on TV.  
ON: Displays on TV.  
NOTE  
%DISPLAY ON TV  
Displays the camera’s on-screen  
display on TV.  
This setting is available only if the TV is connected with the  
AV/S-Video cables. If connected with a DV cable, camera’s  
on-screen display can not be displayed on TV.  
ZFACTORY PRESET  
Returns all the camera settings to  
their default values.  
YES: Performs the function.  
NO: Cancels the function.  
:CLOCK ADJUST  
Enables you to set the time.  
(੬ pg. 13)  
DATE / TIME  
-VIDEO NO. RESET  
YES: Performs reset.  
NO: Cancels reset.  
NOTE  
.IMAGE NO. RESET  
By resetting the file number  
(name), a new folder will be made.  
The new files will be stored in the  
new folder.  
It is convenient to separate the new  
files from previously recorded files.  
Even if you select [YES], you can cancel the process by  
selecting [STOP].  
,FORMAT SD CARD  
You have to format newly  
[FILE]: Initializes all files in the microSD card.  
FILE + MANAGEMNET NO: Initializes all files and  
management numbers in the microSD card.  
purchased microSD cards with  
this camera before using them.  
This will also ensure stable speeds  
and operation when accessing the  
microSD card.  
2 FORMAT HDD  
[FILE]: Initializes all files in the hard disk drive.  
FILE + MANAGEMNET NO: Initializes all files and  
management numbers in the hard disk drive.  
This will ensure stable speeds and  
operation when accessing the hard  
disk drive.  
65  
Changing the Menu Settings (Continued)  
Settings: [ ] = Factory-preset  
Menus  
BASIC SETTINGS  
Select [BASIC SETTINGS], then select sub-menus.  
1 CLEAN-UP HDD  
YES: Performs cleanup.  
NO: Cancels the function.  
NOTE  
Writing speed to HDD tends to  
become slow after long periods  
of repeated use. Execute cleanup  
periodically to regain the writing  
speed.  
Even if you select [YES], you can stop the process by  
selecting [STOP].  
0 DELETE DATA ON HDD  
This will make it more difficult to  
recover data on the HDD which  
has already been erased. It is  
recommended that you activate  
this function when disposing of  
the camera to prevent illegal data  
recovery (using commercially  
available software).  
YES: Deletes data on HDD.  
NO: Cancels the function.  
NOTE  
Even if you select [YES], you can stop the process by  
selecting [STOP].  
66  
FURTHER INFORMATION  
Troubleshooting  
The camera is a microcomputer-controlled  
device. External noise and interference (from  
a TV, a radio, etc.) might prevent it from  
functioning properly.  
To solve the problem, first follow the  
instructions below.  
If the problem is not solved, reset the  
camera. (੬ below)  
If the problem persists, please consult your  
nearest JVC dealer.  
•
•
•
The following phenomena are not  
malfunctions.  
LTo reset the camera  
The camera heats up when it is used for a  
long time.  
•
1) Close the LCD monitor to turn off the  
camera and remove the power supply  
(battery pack or AC adapter) from the  
camera, then reattach it.  
The battery heats up during charging.  
When playing back a video file, the  
image stops momentarily or the sound is  
interrupted at junctions between scenes.  
•
•
2) Select [FACTORY PRESET] from the  
MENU. (੬ pg. 65)  
Trouble  
Action  
੬
Connect the AC adapter securely.  
Detach the battery pack once again and reattach it firmly.  
Replace the dead battery with a fully charged one.  
16  
16  
–
•
•
•
•
No power is supplied.  
If the camera is not operated for 5 minutes while the power  
is on, it turns itself off automatically to conserve power. To  
turn the camera on again when using the battery pack,  
close the LCD monitor and open it again. When using the  
AC adapter, perform any operation such as zooming.  
Adjust the brightness of the LCD monitor.  
–
No display appears.  
64  
–
•
•
Move to a place where not affected by vibration or  
excessive sound.  
The drop detection function operated. Close the LCD  
monitor and open it again. To turn off this function, set  
[DROP DETECTION] to [OFF].  
The power was turned  
off accidentally.  
64  
•
The displayed amount  
of remaining battery  
power differs from the  
actual operating time.  
Fully charge the battery, and then run it down. If the  
problem persists, the battery is worn out and needs to be  
replaced. Please purchase a new one.  
16  
•
The power does not  
turn on, or the battery  
operation time is  
extremely short even  
after the battery is fully  
charged.  
Make sure to use the camera under appropriate operating  
temperatures.  
The battery is worn out and needs to be replaced. Please  
purchase a new one.  
72  
–
•
•
Charging may stop in places subject to extremely high/low  
temperatures to protect the battery. It is recommended  
to charge it in places with a temperature of 10°C to 35°C  
(50°F to 95°F).  
When the battery is already fully charged, the lamp does  
not light. Check the remaining battery power.  
–
•
The access/charge  
lamp on the camera  
does not light during  
charging.  
18  
•
67  
Troubleshooting (Continued)  
Trouble  
Action  
੬
Adjust the brightness and angle of the LCD monitor.  
When the LED light reaches the end of its service life,  
images on the LCD monitor become dark. Consult your  
nearest JVC dealer.  
64  
–
•
•
Images on the LCD  
monitor appear dark or  
whitish.  
The LCD monitor is made with high precision technology.  
However, black spots or bright spots of light (red, green or  
blue) may appear constantly on the LCD monitor. These  
spots are not recorded on the picture. This is not due to  
any defect of the unit. (Effective dots: more than 99.99%)  
–
•
•
Colored bright spots  
appear on the LCD  
monitor.  
Change the settings in [SELECT TV TYPE] to match  
the aspect ratio of the image with the screen size of the  
connected TV.  
65  
Aspect ratio of the  
image is strange when  
watching images on TV.  
Recording medium is full. Delete unnecessary files or  
replace the microSD card.  
32  
•
Recording cannot be  
performed.  
Select the recording medium properly.  
64  
–
•
•
Such a phenomenon occurs when shooting a subject  
illuminated by bright light. This is not a malfunction.  
Vertical lines appear on  
recorded images.  
The LCD monitor  
becomes red or black  
for an instant.  
Such a phenomenon occurs when shooting under direct  
sunlight. This is not a malfunction.  
–
15  
–
•
•
•
During recording, the  
date/time does not  
appear.  
Touch the DISP button once.  
The temperature of the camera is increasing. If the  
camera continues to heat up, recording may be stopped  
to protect the recording medium. In this case, turn off the  
power, and then wait until the camera cools down.  
During video recording,  
the 7REC indicator  
flashes.  
Certain modes of program AE, effect, DIS and other  
functions that cannot be used together are selected at the  
same time.  
–
•
The LCD monitor  
indications blink.  
Change the settings in [ZOOM].  
Digital zoom is not available in the still image recording  
mode.  
63  
–
•
•
Digital zoom does not  
work.  
Set [FOCUS] to [AUTO].  
25  
71  
The focus is not  
adjusted automatically.  
•
•
•
Clean the lens and check the focus again.  
Wait to become natural color. The camera adjusts the  
white balance automatically but it takes a time.  
Try manual white balance adjustment.  
In bright places, setting [PROGRAM AE] to [NIGHT] or a  
slow speed is not recommended.  
When the recorded image is too dark, try backlight  
compensation or adjust brightness.  
–
26  
–
•
•
The color of the image  
looks strange.  
24, 25  
25  
•
•
When the recorded image is too bright, try adjust  
brightness.  
68  
Trouble  
Action  
੬
Do not select the sepia (SEPIA) or monotone  
26  
White balance setting  
cannot be activated.  
•
•
(MONOTONE) mode before setting white balance.  
The continuous shooting speed will drop after repeated  
continuous shots, depending on the recording media, or  
under certain recording conditions.  
–
The continuous  
shooting speed is slow.  
Select the recording medium properly.  
To watch images on a TV, set the TV’s input mode or  
channel that is appropriate for video playback.  
64  
31  
•
•
Playback cannot be  
performed.  
The same image is  
displayed for a long  
time during video  
playback, or motion is  
choppy.  
Replace the microSD card. (When the surface of the card  
is damaged, difficulty in reading the data occurs.)  
Perform clean up or format the microSD card.  
66  
•
•
Do not select the sepia (SEPIA) or monotone  
30  
–
The black & white fader  
does not work.  
•
•
(MONOTONE) mode before setting white balance.  
The driving sound (hum) of the hard disk may have been  
recorded if the camera was moved suddenly during  
recording. Do not move or shake the camera suddenly  
during recording.  
There is a noise during  
playback.  
The temperature of the camera is increasing. If the  
camera continues to heat up, playback may be stopped  
to protect the recording medium. In this case, turn off the  
power, and then wait until the camera cools down.  
–
•
During video playback,  
the Findicator flashes.  
Remove protection from the files and delete them.  
33  
32  
•
•
Files cannot be deleted.  
The data process is too  
slow after the power  
is switched on or the  
mode is changed.  
There is a large number of still images (approx. 1,000 or  
more) stored in the recording medium. Copy the stored  
files to other devices, and delete them from the recording  
medium.  
The microSD card  
cannot be removed  
from the camera.  
Push the microSD card in a few more times.  
19  
–
•
•
The [CREATE DVD]  
screen is displayed in  
the LCD monitor, and  
no other operations  
can be performed.  
Another operation is being attempted while a DVD burner  
that is turned on is connected. Turn off the camera  
connected to the DVD burner, or disconnect the USB  
cable.  
The touch sensor or  
sensor button does not  
function.  
Touch the sensors with your finger. The sensors do not  
function if you touch them with your finger nail or with  
gloves on.  
6
•
69  
Warning Indications  
Indication  
Meaning/Action  
੬
Displays the remaining battery power.  
–
•
•
High  
Exhausted  
(Battery indicator)  
As the battery power comes close to nil, the battery  
indicator blinks. When the battery power is exhausted,  
power turns off automatically.  
–
Appears when the date/time is not set.  
17  
14  
•
•
The built-in clock’s rechargeable lithium battery is  
discharged, so the previously set date/time is erased.  
Connect the camera to an AC outlet using the AC adapter  
for over 24 hours to charge the clock’s lithium battery. Then  
set the date/time.  
SET DATE/TIME!  
Appears for 5 seconds after power is turned on in recording  
mode if the lens cover is closed or when it is dark.  
–
•
CHECK LENS COVER  
Perform clean up to restore the capacity of the recording media.  
19  
•
•
Turn off the camera. Remove the microSD card and insert it 65, 66  
again. Turn on the camera after inserting the microSD card.  
If the error message appears again, replace the card with  
one that is certified to operate correctly.  
HDD ERROR!  
MEMORY CARD ERROR!  
It is also recommended to run check disc regularly on the  
PC, providing that there is no data on the hard disk of the  
camera.  
–
•
•
VIDEO MANAGEMENT  
FILE IS BROKEN.TO  
RECORD/PLAYBACK  
VIDEO, RECOVERY IS  
REQUIRED. RECOVER?  
The video management file is broken. Recovery is required  
to record or play back video files. Select [YES], then touch  
the OK button to recover the video management file.  
–
The writing speed of recording medium is slow, or the  
recording medium is corrupted. Use a microSD card that is  
guaranteed to operate correctly.  
The hard disk was subjected to vibrations or jolts. Be careful  
not to subject the hard disk to vibrations or jolts.  
Appears when the recording medium is full and recording  
is not possible. Delete unnecessary files, or replace the  
microSD card.  
19  
•
–
•
•
RECORDING FAILURE  
32  
Appears when an incompatible USB device is connected to  
the camera.  
Appears when a DVD burner that is switched off is  
connected. If you want to use the DVD burner, switch the  
power on.  
–
–
•
•
POWER IS OFF,  
OR USB DEVICE IS  
UNSUPPORTED  
70  
Indication  
Meaning/Action  
੬
RECORDING MAY NOT  
BE CORRECT ON THE  
MEMORY CARD  
Confirm the operation procedure and try recording again.  
Replace the microSD card.  
–
–
•
•
DROP DETECTION  
WORKED AND THE  
POWER IS TURNED OFF  
To turn on the camera again, close the LCD monitor and  
open it again.  
–
•
Cleaning  
Before cleaning, turn off the camera and remove the battery pack and AC adapter.  
LTo clean the exterior  
Wipe gently with a soft cloth. If the camera is particularly dirty, dip the cloth into diluted mild  
soap and wring it out well before wiping. Then wipe again with a dry cloth.  
LTo clean the LCD monitor  
Wipe gently with a soft cloth. Be careful not to damage the monitor.  
LTo clean the lens  
Wipe gently with lens cleaning paper.  
NOTES  
Avoid using strong cleaning agents such as benzine or alcohol.  
Mold may form if the lens is left dirty.  
When using a cleaner or chemically treated cloth, refer to the cautions for each product.  
•
•
•
71  
Specifications  
LED Light  
Within 1.5 m (4.9 ft)  
Camera  
(recommended shooting distance)  
LFor general  
Language  
English/French/Spanish/Portuguese/  
Japanese/Korean/Traditional Chinese  
Power supply  
DC 11 V (Using AC adapter)  
DC 7.2 V (Using battery pack)  
Power consumption  
[GZ-MG467]  
Approx. 3.2 W*  
[GZ-MG360/335/330]  
LFor video/Audio  
Format  
SD-VIDEO  
Recording/Playback format  
Video: MPEG-2  
Approx. 2.7 W*  
*When the LED light is off and the monitor  
backlight is set to [STANDARD] mode.  
Dimensions (W x H x D)  
113 mm x 68 mm x 54 mm  
(4-1/2" x 2-11/16" x 2-3/16")  
Weight  
Audio: Dolby Digital (2 ch)  
Signal format  
NTSC standard  
Recording mode (video)  
ULTRA FINE: 720 x 480 pixels, 8.5 Mbps (VBR)  
FINE: 720 x 480 pixels, 5.5 Mbps (VBR)  
NORMAL: 720 x 480 pixels, 4.2 Mbps (VBR)  
ECONOMY: 352 x 240 pixels, 1.5 Mbps (VBR)  
Recording mode (audio)  
ULTRA FINE: 48 kHz, 384 kbps  
FINE: 48 kHz, 384 kbps  
[GZ-MG467]  
Approx. 315 g (0.69 lbs)  
(incl. grip belt)  
Approx. 400 g (0.88 lbs)  
(incl. battery and grip belt)  
[GZ-MG360/335/330]  
Approx. 315 g (0.69 lbs)  
(incl. grip belt)  
Approx. 360 g (0.79 lbs)  
(incl. battery and grip belt)  
Operating temperature  
0°C to 40°C (32°F to 104°F)  
Operating humidity  
35% to 80%  
NORMAL: 48 kHz, 256 kbps  
ECONOMY: 48 kHz, 128 kbps  
LFor still image  
Format  
JPEG  
Image size  
[GZ-MG467]  
2 modes (1152 x 864 / 640 x 480)  
[GZ-MG360/335/330]  
1 mode (640 x 480)  
Picture quality  
2 modes (FINE/STANDARD)  
Storage temperature  
–20°C to 50°C (–4°F to 122°F)  
Pickup  
[GZ-MG467]  
1/6" (1,070,000 pixels) CCD  
[GZ-MG360/335/330]  
1/6" (680,000 pixels) CCD  
Lens  
LFor connectors  
AV input/output*  
Video input: 0.8 V (p-p) ~ 1.2 V (p-p), 75 Ω  
Video output: 1.0 V (p-p), 75 Ω  
Audio intput: 300 mV (rms), 50 kΩ  
Audio output: 300 mV (rms), 1 kΩ  
* Only GZ-MG467/335  
[GZ-MG467]  
Video: F 1.8 to 4.5, f = 2.5 mm to 80 mm, 32:1  
power zoom lens  
Still image: F 1.9 to 4.5, f = 2.9 mm to 80 mm,  
27:1 power zoom lens  
[GZ-MG360/335/330]  
F 1.8 to 4.0, f = 2.2 mm to 77 mm, 35:1 power  
zoom lens  
USB  
Mini USB type A and type B, USB 2.0  
compliant  
Filter diameter  
ø30.5 mm  
AC Adapter  
Power requirement  
AC 110 V to 240 Vd, 50 Hz/60 Hz  
Output  
LCD monitor  
2.7" diagonally measured, LCD panel/TFT  
active matrix system  
Speaker  
DC 11 V  
, 1 A  
§
Monaural  
72  
Operating temperature  
0°C to 40°C (32°F to 104°F)  
Dimensions (W x H x D)  
42 mm x 14.5 mm x 91 mm  
(1-11/16" x 5/8" x 3-5/8")  
Weight  
Remote Control  
Power supply  
DC 3 V  
Battery life  
Approx. 1 year (depending on the frequency of  
Approx. 30 g (0.07 lbs)  
(incl. battery)  
use)  
Operating distance  
Within 5 m (16.4 ft)  
Design and specifications subject to change  
without notice.  
Approximate recording time (minutes) (for video)  
Recording medium  
HDD  
microSD Card  
30 GB*1  
60 GB*2  
860  
4 GB  
57  
Quality  
ULTRA FINE  
430  
640  
FINE  
NORMAL  
1280  
1700  
4500  
85  
850  
113  
298  
ECONOMY  
2250  
*1 GZ-MG335/330 *2 GZ-MG467/360  
[GZ-MG467] Approximate number of storable images (for still image)  
HDD  
microSD Card  
Recording medium  
Image size/Quality  
1152 x 864 / FINE  
60 GB  
9999  
9999  
9999  
9999  
256 MB  
535  
512 MB  
1065  
1 GB  
2140  
3265  
6205  
8865  
2 GB  
4 GB  
8045  
9999  
9999  
9999  
4095  
6145  
9999  
9999  
1152 x 864 / STANDARD  
640 x 480 / FINE  
820  
1625  
1555  
2225  
3090  
640 x 480 / STANDARD  
4420  
[GZ-MG360/335/330] Approximate number of storable images (for still image)  
Recording medium  
HDD  
microSD Card  
30 GB*1 60 GB*2 256 MB 512 MB  
1 GB  
4135  
8865  
2 GB  
7680  
9999  
4 GB  
9999  
9999  
Image size/Quality  
640 x 480 / FINE  
9999  
9999  
9999  
9999  
1035  
2225  
2060  
4440  
640 x 480 / STANDARD  
*1 GZ-MG335/330 *2 GZ-MG360  
Required charging/recording time (approx.)  
*When the LED light is off and the monitor backlight is set to [STANDARD] mode.  
Recording time  
Battery pack  
Charging time  
1 hr. 30 min.  
GZ-MG467  
GZ-MG365/335/330  
1 hr. 50 min.*  
BN-VF808U*1  
(Provided)  
1 hr. 30 min.*  
BN-VF815U*2  
(Provided)  
2 hr. 40 min.  
3 hr. 50 min.  
3 hr. 5 min.*  
3 hr. 40 min.*  
5 hr. 30 min.*  
BN-VF823U  
4 hr. 35 min.*  
*1 GZ-MG360/335/330 *2 GZ-MG467  
73  
Cautions  
AC Adapter  
Recording Medium  
USING HOUSEHOLD AC PLUG ADAPTER  
In case of connecting the unit’s power cord to  
an AC wall outlet other than American National  
Standard C73 series type use an AC plug  
adapter, called a “Siemens Plug”, as shown.  
For this AC plug adapter, consult your nearest  
JVC dealer.  
Be sure to follow the guidelines below  
to prevent corruption or damage to your  
recorded data.  
•
Do not bend or drop the recording medium, or  
•
subject it to strong pressure, jolts or vibrations.  
Do not splash the recording medium with water.  
Do not use, replace, or store the recording  
medium in locations that are exposed to strong  
static electricity or electrical noise.  
•
•
Plug Adapter  
Do not turn off the camera power or remove  
•
the battery or AC adapter during shooting,  
playback, or when otherwise accessing the  
recording medium.  
Do not bring the recording medium near objects  
that have a strong magnetic field or that emit  
strong electromagnetic waves.  
•
Battery Packs  
Do not store the recording medium in locations  
with high temperature or high humidity.  
Do not touch the metal parts.  
•
The supplied battery pack is Terminals  
a lithium-ion battery. Before  
using the supplied battery  
pack or an optional battery  
pack, be sure to read the  
•
When formatting or erasing data using the  
camera, only the file administration information  
is changed. The data is not completely erased  
from the hard disk. If you want to completely  
erase all of the data, we recommend either  
using commercially available software that  
is specially designed for that purpose, or  
by physically destroying the camera with a  
hammer etc.  
•
following cautions:  
To avoid hazards  
•
... do not burn.  
... do not short-circuit the terminals. Keep it away  
from metallic objects when not in use. When  
transporting, make sure the provided battery  
cap is attached to the battery. If the battery  
cap is misplaced, carry the battery in a plastic  
bag.  
LCD Monitor  
... do not modify or disassemble.  
... do not expose the battery to temperatures  
exceeding 60°C, as this may cause the battery  
to overheat, explode or catch fire.  
... use only specified chargers.  
To prevent damage to the LCD monitor, DO  
NOT  
•
... push it strongly or apply any shocks.  
... place the camera with LCD monitor on the  
bottom.  
•
To prevent damage and prolong service life  
•
... do not subject to unnecessary shock.  
... charge within the temperature range of 10°C  
to 35°C (50°F to 95°F). This is a chemical  
reaction type battery — cooler temperatures  
impede chemical reaction, while warmer  
temperatures can prevent complete charging.  
... store in a cool, dry place. Extended exposure  
to high temperatures will increase natural  
discharge and shorten service life.  
To prolong service life  
... avoid rubbing it with coarse cloth.  
... fully charge and then fully discharge the  
battery every 6 months when storing the  
battery pack over a long period time.  
... remove from charger or powered unit when  
not in use, as some machines use current  
even when switched off.  
74  
Changes or modifications not approved  
by JVC could void the user’s authority to  
operate the equipment. This equipment has  
been tested and found to comply with the  
limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection  
against harmful interference in a residential  
installation. This equipment generates, uses,  
and can radiate radio frequency energy and, if  
not installed and used in accordance with the  
instructions, may cause harmful interference  
to radio communications. However, there is  
no guarantee that interference will not occur  
in a particular installation. If this equipment  
does cause harmful interference to radio or  
television reception, which can be determined  
by turning the equipment off and on, the  
user is encouraged to try to correct the  
interference by one or more of the following  
measures: Reorient or relocate the receiving  
antenna. Increase the separation between the  
equipment and receiver.  
Main Unit  
For safety, DO NOT  
... open the camera’s chassis.  
... disassemble or modify the unit.  
... allow inflammables, water or metal objects to  
enter the unit.  
... remove the battery pack or disconnect the  
power supply while the power is on.  
... leave the battery pack attached when the  
camera is not in use.  
... place naked flame sources, such as lighted  
candles, on the apparatus.  
... expose the apparatus to dripping or splashing.  
... leave dust or metal objects adhered to the  
power plug or an AC wall outlet.  
... insert any objects in the camera.  
Avoid using the unit  
... in places subject to excessive humidity or dust.  
... in places subject to soot or steam such as  
near a cooking stove.  
... in places subject to excessive shock or vibration.  
... near a television set.  
... near appliances generating strong magnetic  
or electric fields (speakers, broadcasting  
antennas, etc.).  
•
•
Connect the equipment into an outlet on a  
circuit different from that to which the receiver  
is connected.  
Consult the dealer or an experienced radio/  
TV technician for help.  
... in places subject to extremely high (over 40°C)  
or extremely low (under 0°C) temperatures.  
... in places where the air pressure is low (more  
than 3000 m (9870 ft) above the sea level).  
DO NOT leave the unit  
•
... in places of over 50°C.  
... in places where humidity is extremely low  
(below 35%) or extremely high (above 80%).  
... in direct sunlight.  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Cet appareil numérique de la classe B est  
conforme à la norme NMB-003 du Canada.  
... in a closed car in summer.  
... near a heater.  
... in high places such as on a TV. Leaving the  
unit in high places while a cable is connected  
may result in a malfunction if the cable is  
caught and the unit falls onto the floor.  
To protect the unit, DO NOT  
•
... allow it to become wet.  
... drop the unit or strike it against hard objects.  
... subject it to shock or excessive vibration  
during transportation.  
... keep the lens directed at extremely bright  
objects for long periods.  
... expose the lens to direct sunlight.  
... swing it excessively when using the hand strap.  
... swing the soft camera case excessively when  
the camera is inside it.  
To prevent the unit from dropping,  
•
•
Attach the shoulder strap securely and fasten  
the grip belt securely.  
When using the camera with a tripod, attach the  
camera to the tripod securely.  
•
If the camera drops, you may be injured and  
the camera may be damaged.  
When a child uses the unit, there must be  
parental guidance.  
75  
Terms  
A AC Adapter ................................................. 16, 74  
Adjust Brightness .............................................. 25  
Analog Input ...................................................... 63  
Auto Power Off .................................................. 65  
M Macintosh ......................................................... 58  
Manual Recording ............................................. 24  
Menu Settings ................................................... 62  
microSD Card ................................................... 19  
Monitor Backlight .............................................. 64  
Monitor Off ........................................................ 63  
B Backlight Compensation ................................... 24  
Battery Pack .......................................... 16, 18, 74  
O Operation Sound ............................................... 65  
C Clean-up HDD .................................................. 66  
Clock Adjust ................................................ 17, 65  
Copying (Moving) Still Images .............. 48, 49, 58  
Copying Video Files .............................. 46, 49, 58  
P Partial Delete .................................................... 35  
Photometry Area ............................................... 26  
PictBridge ......................................................... 40  
Picture Quality .................................................. 62  
Playlist ............................................................... 36  
Power-Linked Operation ................................... 12  
Preset ............................................................... 65  
Printer ............................................................... 40  
Program AE ...................................................... 24  
Protecting Files ................................................. 32  
D Date Display Style ............................................. 64  
Date Index Screen ............................................ 28  
Deleting Files .............................................. 32, 66  
Deleting Playlist ................................................ 38  
Demonstration Mode ......................................... 64  
Digital Image Stabilizer (DIS) ............................ 63  
Direct Printing ................................................... 40  
Display on TV .................................................... 65  
DPOF ................................................................ 39  
Drop Detection .................................................. 64  
DVD Burner ................................................. 42, 43  
DVD Player ....................................................... 47  
DVD Recorder ................................................... 46  
Q Quick Restart .................................................... 64  
R Recordable Time/Number of Images ................ 73  
Recording Medium ................................ 23, 64, 74  
Remote Control ..................................... 11, 12, 64  
Resetting the Camera ....................................... 67  
Resetting the File Number ................................ 65  
E Effect ........................................................... 26, 30  
Event Registration ....................................... 23, 34  
Event Screen .................................................... 28  
Everio Dock ....................................................... 10  
S Screen Size (16:9/4:3) ...................................... 63  
Select TV Type .................................................. 65  
Self-Timer ......................................................... 62  
Shutter Speed ............................................. 26, 62  
Slide Show ........................................................ 27  
Speaker Volume ................................................ 27  
Still Image ......................................................... 21  
F File Information ................................................. 33  
Focus ................................................................ 25  
Formatting a Recording Medium ...................... 65  
G Gain Up ............................................................. 62  
T Tele Macro ........................................................ 26  
Tripod Mounting ................................................ 18  
TV ..................................................................... 31  
H Hard Disk .......................................................... 74  
I
Image Rotation ................................................. 27  
Image Size ........................................................ 62  
V VCR .................................................................. 46  
Video ................................................................. 20  
L Language Setting ........................................ 17, 64  
LCD Monitor .......................................... 12, 14, 74  
LED Light .......................................................... 22  
Lens Cover ........................................................ 18  
W White Balance ................................................... 26  
Wind Cut ........................................................... 63  
Windows PC ..................................................... 49  
Wipe or Fader Effects ....................................... 30  
Z Zooming ...................................................... 22, 63  
UC  
© 2008 Victor Company of Japan, Limited  
0108FOH-AL-OT  

A O Smith Genesis GW 1500 User Manual
Audiovox 27PL User Manual (1)
Audiovox TERK TV5 User Manual
Behringer iNuke NU3000 User Manual
Bryan Boilers Broile System User Manual
Burnham MEGASTEAM MST629 User Manual
Bushnell NIGHT VISION 26 3652 User Manual
Cuisinart CBT 500 User Manual
Eclipse Fujitsu Ten Car Stereo System CD8061 User Manual
JVC GR AX201 User Manual