JVC Car Video System DT 3D24G1 User Manual

The lightning ﬂash with arrowhead

symbol, within an equilateral triangle is

intended to alert the user to the presence

of uninsulated “dangerous voltage”

within the product’s enclosure that may

be of sufﬁcient magnitude to constitute a

risk of electric shock to persons.

CAUTION

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

The exclamation point within an

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servicing)

instructions in the literature

To reduce the risk of electric shock. Do

not remove cover (or back). No user

serviceable parts inside. Refer servicing

to qualiﬁed service personnel.

CAUTION:

accompanying the appliance.

MULTI FORMAT 3D LCD MONITOR

DT-3D24G1

INSTRUCTIONS

For Customer Use:

Enter below the Serial No. which is located on the rear of

the cabinet. Retain this information for future reference.

Model No.

Serial No.

DT-3D24G1

LCT2655-001A-H

• Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from

overheating. These openings must not be blocked or covered.

• Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-circuit the parts,

which could result in a fire or electric shock.

• Never spill liquid of any kind on the product.

• Never place anything on the product. (Placing liquids, naked flames, cloths, paper, etc. on the product may cause a fire.)

• Do not apply any strong shock to the LCD panel. (Do not hit any object against it or push it with a sharp-pointed tool.)

• Do not put heavy objects on the product.

• Do not step on or hang on the product.

To prevent an accidental fall

VESA mounting holes

Fix the monitor to a wall by using strings.

Fixing the monitor

Attach the hook (not provided) to the VESA mounting holes on the

rear panel (use the two holes on the upper side) using M4 x 10

mm screws (not provided). Bind the hooks on the rear panel of the

monitor to a wall or a pillar using durable string.

Hook and screw (M4 x 10 mm)

(not provided)

Hook (not provided)

U.S.A. only

FCC NOTICE

CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.

IMPORTANT RECYCLING INFORMATION

This product has a fluorescent lamp that contains mercury. Disposal of these materials may be regulated in your

community due to environmental considerations. For disposal or recycling information, please contact your local

authorities or for USA, the Electronic Industries Alliance: http://www.eiae.org

WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE.

WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE

EARTHING CONNECTION.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH

THE SAME OR EQUIVALENT TYPE.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from

the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be

placed on the apparatus.

16) Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

17) When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries

must be followed strictly.

Safety Precautions (cont.)

European Union only

Dear Customer,

EMC Supplement

This apparatus is in conformance with the valid European directives and

standards regarding electromagnetic compatibility and electrical safety.

This equipment is in conformity with the provisions and protection

requirements of the corresponding European Directives. This

equipment is designed for professional video appliances and can be

used in the following environments:

• Controlled EMC environment (for example purpose built

broadcasting or recording studio), and rural outdoors environment

(far away from railways, transmitters, overhead power lines, etc.)

In order to keep the best performance and ensure electromagnetic

compatibility, we recommend to use cables not exceeding the

following length:

European representative of Victor Company of Japan, Limited is:

JVC Technical Services Europe GmbH

Postfach 10 05 04

61145 Friedberg

Germany

Information for Users on Disposal of Old Equipment

[European Union]

This symbol indicates that the electrical and

electronic equipment should not be disposed

as general household waste at its end-of-life.

Instead, the product should be handed over to

the applicable collection point for the recycling

of electrical and electronic equipment for proper

treatment, recovery and recycling in accordance

with your national legislation.

Cable

Length

Power cord

2.0 m

(attached cable (H05VV-F 3 x 0.75 mm²))

Video signal cable (coaxial cable)

Audio signal cable (shielded cable)

DVI cable (shielded cable) with core filter

2.0 m

1.5 m

2.0 m

RS-232C cable (shielded cable)

(A straight cable with a D-sub 9-pin connector)

By disposing of this product correctly, you will

help to conserve natural resources and will

help prevent potential negative effects on the

environment and human health which could

otherwise be caused by inappropriate waste

Attention:

This symbol is

only valid in the

European Union.

RS-485 cable (twist pair cable)

(A straight LAN cable)

2.0 m

REMOTE cable (twist pair cable)

(A straight LAN cable)

handling of this product. For more information about collection point

and recycling of this product, please contact your local municipal

office, your household waste disposal service or the shop where you

purchased the product.

The inrush current of this apparatus is 15.44 ampere.

Penalties may be applicable for incorrect disposal of this waste, in

accordance with national legislation.

CAUTION

In case where the strong electromagnetic waves or magnetism are

near the audio cable or the signal cable, the sound or the picture will

contain noise. In such cases, please keep the cable away from the

sources of the disturbance.

(Business users)

If you wish to dispose of this product, please visit our web page http://

www.jvc.eu/ to obtain information about the take-back of the product.

[Other Countries outside the European Union]

If you wish to dispose of this product, please do so in accordance

with applicable national legislation or other rules in your country for

the treatment of old electrical and electronic equipment.

Operating Precautions

The LCD panel and backlight have life expectancy. Due to the basic characteristics of the LCD panel, an afterimage or uneven display may occur. It is

recommended that you change images occasionally, activate the power saving function, or often turn off the power to reduce the load on the LCD panel. Charges

will apply for repairs resulting from deterioration due to the passage of time.

Caution for use of the product for many hours

In the case that you use the monitor for many hours, we recommend that you set “NO SYNC ACTION” in “SYNC FUNCTION” to “P.SAVE” in MAIN MENU. This

will reduce power consumption and relieve strain on the monitor. (

→

page 22)

Caution for use of the product in the high temperature

Do not use the product in places of high temperature; otherwise, parts of this product or the LCD panel may be damaged. This product is equipped with a

temperature sensor to give warning if the temperature becomes too high. If the temperature exceeds the range of normal use, “TEMP. OVER” is displayed, and

the power is turned off automatically if the temperature becomes any higher. In this case, move the product to a place of low temperature to let it cool down.

Maintenance

Screen

Cabinet

To avoid irreparable change in appearance of the screen such as uneven

color, discoloration, scratches, be careful about the following:

To avoid the deterioration or damages of the cabinet such as its paint’s

peeling away, be careful about the following:

●

Do not paste or stick anything using any glues or adhesive tapes.

Do not write anything on the screen.

Do not strike the screen with a hard object.

●

Do not wipe the cabinet using solvent such as alcohol, thinner, or benzine.

Do not expose the cabinet to any volatile substance such as insecticides.

Do not allow any rubber or plastic in contact for a long time.

Do not wipe the cabinet forcefully.

Avoid condensation on the screen.

Do not wipe the screen with any liquid such as water. In addition, wiping

the screen with water-diluted neutral detergent or solvent such as alcohol,

thinner, or benzine may affect the anti-reflection treatment of the screen.

Do not wipe the screen forcefully.

Wipe stains off the cabinet with a soft cloth. If the cabinet gets heavily stained,

wipe it with a soft cloth soaked in water-diluted neutral detergent and wrung

well, then wipe with a soft dry cloth.

●

Glasses

Wipe the glasses with a dry, soft cloth.

Wipe stains off the screen with a soft cloth.

Ventilation openings

Use a vacuum cleaner to get rid of the dust around the intakes (all the

openings). If a vacuum cleaner is not available, use a cloth and wipe it off.

Leaving the dust around the intakes may prevent proper temperature control

and cause damage to the product.

Note: Be sure to read “When viewing in 3D” on page 12 for proper viewing beforehand.

Flicker-free 3D images by circular polarizing

Compatible with side-by-side and line-by-line formats to provide flicker-free 3D images

3D mixer converting L/R dual signals to a 3D mixed format

Mixes and converts images taken with a stereo camera rig to 3D images

Various functions useful on the spot

CAMERA ASSIST MENU: 7 menus useful in various shooting scenes

3D cursor: “Cursor mode” for displaying the visual difference between left and right eyes in

pixels/percentage; “Grid mode” for checking the visual difference by grid lines

Table of Contents

Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Operating Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Daily Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Viewing 3D images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Basic 3D principle

Compatible 3D format

When viewing in 3D

To view 3D images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

To view existing 3D images

To view images taken by two cameras

Setting the CAMERA ASSIST MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Other 3D functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

SCOPE button/lamp

3D CURSOR button/lamp

Setting the menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MAIN MENU

SET-UP MENU

External control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Self-check program

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Available signals

Dimensions

Installation

● Do not rest your arm on the monitor or lean against the monitor.

● Do not touch the LCD panel when installing the monitor.

● Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury.

● How to set up 1

● To detach the stand

You can tilt the monitor as follows.

Lay the monitor on a cloth with the LCD panel facing down to

prevent the LCD panel from being damaged.

When the monitor is not tilted

(0°), the guidelines align as

illustrated below.

Attachment screws

Screw holes for stand

Stand body

attachment

Guidelines

Monitor

Approx. 6°

0°

Stand

Approx. 6°

● To install the stand

When attaching the stand to the monitor, insert the guides of

the stand plate into the guide holes on the monitor to place the

stand in the correct position. Then fix the stand firmly with the

attachment screws.

● Be careful not to pinch your fingers in the gap between the

monitor and the stand.

● When the stand plate is attached to the lower position of the stand

body, you cannot tilt the monitor downward.

Guide holes

● How to set up 2

When the stand plate is attached to the higher position of the stand

body, you can place the monitor as illustrated below.

1 Remove the screws on the sides of the stand (see the following

illustration), and lift up the stand by approximately 148 degrees.

Approx. 148°

Screw (silver)

Guides

Monitor

Screw holes for stand

attachment

Stand plate

2 Attach the removed screws and place the monitor as illustrated

below.

Stand body

● To adjust the stand height

To change the stand height, detach the stand from the monitor.

Then, change the position of the stand plate according to the

stand height you want by choosing the screw holes to use.

●

To place the monitor as shown in “How to set up 1” again, remove

the screws on the sides of the stand, align the guidelines, and then

reattach the screws.

Screw holes

for higher position

Screw holes

for lower position

Cautions

● When lifting up the stand...

Lay the monitor on a cloth with the LCD panel facing down to

prevent the LCD panel from being damaged.

Stand

plate

Be careful not to pinch your fingers in the moving parts.

● Make sure of lifting the stand up until it stops (Approx. 148°);

otherwise the monitor may fall over.

● Place the monitor on a mat to avoid scratching the table surface.

● Do not lift up the stand when the stand plate is attached to the

lower position of the stand body.

Connections

Rear panel

Security slot

Attach a security

wire to this slot.

Note for connections

•

Before making any connections, turn off all the equipment.

Use a cord whose plugs correctly match the terminals on this monitor

and the equipment.

•

Plugs should be firmly inserted; poor connections could cause noise.

When unplugging a cord, be sure to grasp its plug and pull it out.

DO NOT connect the power cord until all connections are complete.

Refer also to the user manual of each piece of equipment.

DC IN 24V terminal

AUDIO (IN) terminals (pin jack)

Terminal for DC 24V power supply (Voltage range: DC 23.3V − DC 25.5V).

Input terminals for the analog audio signals.

●

Use this terminal for the analog audio connection of the SDI.

When a superimposed signal (EMBEDDED AUDIO signal on

an SDI signal) is input, analog audio signals cannot be input.

When using the DC 24V power supply (Voltage range: DC 23.3V − DC

25.5V), check the pin number, signal, and polarity of the DC IN 24V

terminal. A wrong connection may cause fire or injuries.

AUDIO MONITOR OUT (OUT 1(L), OUT 2(R)) terminals (pin jack)

Output terminals for the analog audio signal.

●

When both AC power and DC 24V

power are connected, the AC power

has priority. When the AC power is

switched off, the power automatically

switches to the DC 24V power.

Use the DC power equipped with LPS (Limited Power Sources).

●

The terminals emit the audio signals through the AUDIO (IN)

terminal or EMBEDDED AUDIO signals through the E. AUDIO

3G SDI/HD SDI/SD SDI (IN 1/L or IN 2/R) input terminal.

The signal is output from this terminal only when the monitor is on or

●

in “P.SAVE” (power save) mode (

→

“NO SYNC ACTION” on page 22).

● Use the DC 24V power that supplies 4.8 A.

● The EMBEDDED AUDIO signal...

– is decoded into an analog signal, then emitted.

AC POWER switch

Turns AC power on or off.

● You need to press

–

is emitted only when “SDI 1/L” or “SDI 2/R” is selected, and

when EMBEDDED AUDIO signals come in to the E. AUDIO 3G

SDI/HD SDI/SD SDI (IN 1/L or IN 2/R) terminal.

button (→ a on page 9) to use

the monitor after turning on the AC POWER switch.

AC IN terminal

AC power input connector. Connect the provided AC power

cord to an AC outlet.

●

E. AUDIO 3G SDI/HD SDI/SD SDI (IN 1/L, IN 2/R) terminals (BNC)

Input terminals for the 3G SDI/HD SDI/SD SDI signals.

●

The terminals accept also EMBEDDED AUDIO signals including

up to 12 audio channels with a sampling frequency of 48 kHz.

Attach the provided power cord holder to prevent

accidental disconnection of the AC power cord. (

→

below)

● Use SDI IN 1/L and SDI IN 2/R terminal when selecting

DUAL LINK SDI for the input.

Caution: Do not connect the power cord until all other

connections are completed.

●

In the stereo camera rig shooting, the L image is input into the SDI IN

1/L terminal, and the R image into the SDI IN 2/R terminal. In the case

of 3G SDI LEVEL B, the image is input into the SDI IN 1/L terminal.

For 3G SDI LEVEL B Dual Stream, input into the SDI IN 1/L

terminal. For 3G SDI LEVEL B DUAL LINK mapping, input into

the SDI IN 1/L and SDI IN 2/R terminals.

REMOTE terminal

Terminal for controlling the monitor by an external control

(→ “External Control” on page 26).

DVI-D (HDCP) terminals

Input terminal for the DVI-D signal compatible with HDCP.

● When the picture is not displayed correctly, change the

setting of “DVI INPUT SEL.” (→ page 25)

E.AUDIO 3G SDI/HD SDI/SD SDI (ACTIVE OUT) terminal (BNC)

Output terminal for the 3G SDI/HD SDI/SD SDI signals.

●

The SDI IN 1/L and SDI IN 2/R input signals are reclocked and output.

● The signals are emitted from this terminal only when

the monitor is on or in “P.SAVE” (power save) mode.

Attaching the power cord holder

The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal. The holder consists of two parts: the cord case and the case cover.

case cover

AC IN terminal

cord case

To take off the case cover

● Do not use any screws other than those supplied.

● Push the case cover into the cord case and check that the power plug is connected firmly.

Daily Operations

Front panel

Tally lamp

This lamp is controlled by the tally function of the MAKE/TRIGGER terminal.

•

You can select the color of the tally lamp from “GREEN” or “RED.”

(→ “TALLY SELECT” in “FUNCTION SETTING” on page 23 and “External Control” on page 26)

• “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even

when the function does not actually work).

• You cannot use the buttons for the items controlled by the MAKE system (“REMOTE ON” appears, and the lamp does not light up).

1 Speakers (stereo)

4 POSITION knob/PUSH SEL. button

The speakers emit the same audio signal emitted from the

AUDIO MONITOR OUT terminals.

POSITION knob: Adjusts the positions of the display line

and R image.

(→ 7 “AUDIO MONITOR OUT(OUT (L), OUT (R)) terminals” on

page 7)

Used for the following functions

• 3D cursor (→ page 16)

• SPLIT (→ page 15)

• LR SEQ. (→ page 15)

• R SHIFT (→ page 15)

2 VOLUME adjustment knob

Adjusts the volume.

3 Picture adjustment knob

• ANAGLYPH (→ page 15)

• INDIVIDUAL (→ page 15)

CHROMA: Adjusts the picture color density.

PUSH SEL. button: Switches the display line.

Used for the following functions

• 3D cursor (→ page 16)

BRIGHT:

Adjusts the picture brightness.

CONTRAST: Adjusts the picture contrast.

● CHROMA cannot be adjusted for certain signal

formats.

• SPLIT (→ page 15)

●To reset the displayed line and R image to default,

press and hold the PUSH SEL. button for 3 seconds

or longer.

5 MUTING button

r T.C. (time code) button/lamp

Turns off the sound when no menu screen is displayed (Muting).

● To cancel the function, press the button again or turn

the VOLUME adjustment knob.

Activates/deactivates the display of the time data (time code)

contained in the SDI signal (→ “On the Information Display”

on page 10).

●

Muting function is also canceled when “BALANCE” of “AUDIO

SETTING” in the MAIN MENU is changed ( page 21).

● Select the time code type in “INFORMATION” of SET-UP

MENU (→ page 24).

→

buttons

t SELECT button

When a menu screen is displayed

Selects or adjusts menu items ( “Menu Operations” on page 18).

Selects/Changes items.

→

Used for the following item/function.

• 3D format (→ page 19)

• 3D cursor (→ page 16)

When no menu screen is displayed

Selects the audio channels of EMBEDDED AUDIO signals

(→ “Audio Channel Selection” on page 10).

• INDIVIDUAL (→ page 15)

● Pressing button while holding button displays the

SET-UP MENU (→ “Menu Operations” on page 18).

y 3D button/lamp

Activates/Deactivates the 3D mode.

● Corrects images for 3D viewing with circular polarizing

glasses.

7 MENU button

Activates/deactivates the display of the MAIN MENU

(→ “Menu Operations” on page 18).

u CAMERA ASSIST button/lamp

8 COLOR OFF button/lamp

Displays/Hides the CAMERA ASSIST MENU (→ page 14).

Displays only the luminance signal.

● Only works for images available in MIX mode.

● This function does not work for RGB input signals.

i MIX button/lamp

9 1:1 button/lamp

Activates/Deactivates the MIX mode.

● Mixes L and R images and converts to side-by-side

images (→ page 13).

Displays the picture in the original resolution of the input signal.

● The aspect ratio of the picture may change depending

on the input signal.

o INPUT SELECT buttons/lamps

p MARKER button/lamp

Selects an input.

Displays/Hides the area marker/safety marker.

SDI 1/L:

SDI 2/R:

DUAL LINK:

DVI:

Input from the E. AUDIO 3G SDI/HD SDI/

SD SDI (IN 1/L) terminal

Input from the E. AUDIO 3G SDI/HD SDI/

SD SDI (IN 2/R) terminal

Input from the E. AUDIO 3G SDI /HD SDI/

SD SDI (IN 1/L, IN 2/R) terminals

Input from the DVI-D (HDCP) terminal

●

Configure the setting in “MARKER” of the MAIN MENU (

→

page 20).

● Available when both the 3D and MIX modes are “OFF.”

● Not activate when picture is displayed in the 1:1 mode.

●

The area marker can only be displayed in 16:9 display mode.

q 3D CURSOR button/lamp

Displays/Hides the cursor for measuring the visual difference

during 3D display (→ page 16).

● The lamp for the selected input lights.

● The SDI 1/L and SDI 2/R lamps light up in MIX mode.

(Only the SDI 1/L lights up in 3G SDI LEVEL B Dual

Stream input.)

● Each time you press this button, the display mode

changes in the following order.

No display

Cursor mode

; Power lamp

Grid mode

Off:

The power is turned off

Green:

Orange:

The monitor is on

w SCREENS CHECK button/lamp

The monitor is turned off (standby), or the

DC power voltage is reduced while working

and the monitor is shut down

Displays only the selected element (R, G, or B) of the video signal.

● This function does not work for RGB input signals.

●

Each time you press this button, the picture changes in the following order.

Orange blinking: P.SAVE (Power saving) mode (“NO SYNC

ACTION“ in “SYNC FUNCTION“) (→ page 22)

RGB (Normal screen)

Red screen

Blue screen

Green screen

● You cannot turn on the monitor if the DC power is

shut down while the power lamp lights up in orange.

Disconnect the DC connector, set up the DC power

within the operating range, and then connect the

connector again.

e SCOPE button/lamp

Displays/hides the indication of the wave form monitor and

vector scope (→ “SCOPE SETTING” on page 22).

● Each time you press this button, the window changes in

the following order.

button

Turns on and off (on standby) the monitor.

● The AC power switch is equipped on the rear panel of

the monitor (→ 2 on page 7).

• When the MIX mode is “OFF” or invalid

No display

Wave form monitor

Vectorscope

• When the MIX mode is “ON” (→ page 16)

No display

Parallel wave form monitor

Parallel vector scope

Difference wave form monitor

Difference vector scope

Daily Operations (cont.)

Audio Channel Selection

Select audio channels emitted from the speakers (L/R) and the AUDIO MONITOR OUT(OUT1(L)/OUT2(R)) terminals, when EMBEDDED AUDIO

signals come in to the SDI terminal and SDI input is selected.

● You have to choose a group of selectable audio channels before the channel selection (→ “E.AUDIO GROUP” in “AUDIO SETTING” on page 21).

● The setting is memorized for each input (SDI 1/L and SDI 2/R).

● Works as SDI 1/L in MIX mode and DUAL LINK SDI input.

1 Press or button when a menu is not displayed.

The screen for audio channel selection is displayed.

● The screen for audio channel selection automatically disappears in about 30 seconds after the previous operation.

Audio channel selection screen

Selected item

2 Press

buttons to select the left (L ch) or right (R ch).

buttons to select an audio channel.

3 Press

● Each time you press the button, the audio channel changes according to the settings of “E.AUDIO GROUP.” (→ page 21)

4 Press MENU button.

● The screen for audio channel selection disappears.

On the Information Display

The monitor displays the information below.

● Configure the show/hide setting of each item in the menu. Use the T.C. button (→ r on page 9) to configure 5 and 6.

● Select the position of the information display (→ “POSITION” in “INFORMATION” on page 24).

● When any information of 1 2 3 or 4 above is displayed while signals come in from equipment other than a computer, the picture is

displayed without overlapping the information display area. However, the information display will overlap with the picture when...

– Displaying the picture with higher resolution than the resolution of the panel in 1:1 mode.

– “SD4:3 LARGE” in the “FUNCTION SETTING” of SET-UP MENU is set to “ON.” (→ page 23)

1 Audio level meter

● You can check the conditions of the EMBEDDED AUDIO signals when “LEVEL METER ch” is set to “LINE” or “DIVIDE.”

● Not displayed when “LEVEL METER ch” is set to “OFF.” (→ “AUDIO SETTING” on page 21)

2 Signal format

● Displayed when “STATUS DISPLAY” is set to “ON.” (→ “INFORMATION” on page 24)

● For the contents displayed, see “Available signals” on page 33 and “On the signal format” on page 11.

3 Source name assigned in “CHARACTER SET.”

● Displayed when “SOURCE ID” is set to “ON” or “AUTO.”

● Displayed in large letters when “STATUS DISPLAY” is set to “OFF” or “AUTO.” (→ “INFORMATION” on page 24)

4 CRC error indication

● Displayed when “CRC ERROR” is set to “ON.” (→ “INFORMATION” on page 24)

● A red square is displayed when an error occurs.

5 Time code

● When the input signal includes no time code, “TC – –:– –:– –:– –” is displayed (→ r on page 9).

Time code (When the 3D button is “OFF” in MIX mode or the CAMERA ASSIST MENU is displayed)

TC1: For SDI IN 1/L input signals

TC2: For SDI IN 2/R input signals

DIF: Difference of TC2 from TC1

● When the CAMERA ASSIST MENU is “R SHIFT”, the time code of SDI IN 1/L input signals is displayed in the 5 position.

● It is not displayed when the CAMERA ASSIST MENU is “ANAGLYPH.”

On the Status Display

If you press the INPUT SELECT button (→ o on page 9) currently lit, the status of the input signal and setting of MUTING are displayed for about

3 seconds.

● Make the setting to display/hide the status in “STATUS DISPLAY” of the “INFORMATION.” (→ page 24)

● When “STATUS DISPLAY” is set to “AUTO” or “ON,” the status below is also displayed in the following cases:

– When you change the input

– When the signal condition of the current input changes

– When you turn on the monitor

● When “STATUS DISPLAY” is set to “ON,” the signal format will remain displayed 3 seconds after the status is displayed.

1 Signal format

● For the contents displayed, see “Available signals” on page 33 and “On the signal format” below.

On the signal format

The following messages appear depending on the type of input signals and their conditions.

When a DVI-D signal protected with HDCP is input

➔ “*” (at the end of the indication)

When no video signal comes in

➔ “NO SYNC”

When a noncompliant video signal comes in

➔ “Out of range”

When a signal that does not meet the MIX operating conditions is input in MIX mode

➔ “Unsupported”

2 Signal format of DVI input

→ On page 25 “DVI INPUT SEL.”

Status indication of DUAL LINK/3G SDI signal information

● “DUAL LINK” appears when the MAIN MENU “SDI DUAL LINK” (→ page 19) is set to “ON” in SDI input, and the 3G SDI signal

information appears when the MAIN MENU “SDI DUAL LINK” is set to “OFF.” However in MIX mode, the 3G SDI signal

information appears even when the MAIN MENU “SDI DUAL LINK” is set to “ON.”

Status indication of 3G SDI signal information

Following signal information can be displayed when a 3G SDI signal comes in.

3G A-1:

3G A-2:

3G A-3:

3G A-4:

Level A mapping structure 1

Level A mapping structure 2

Level A mapping structure 3

Level A mapping structure 4

3G B-DS1: Level B data stream 1

3G B-DS2: Level B data stream 2

3G B-DUAL: Level B DUAL LINK

3G B-DS1/2: Level B Dual stream mapping (in MIX mode)

3D format conversion method

● The 3D format conversion method appears when the 3D mode is activated while the MIX mode is “OFF.”

(→ page 19 “SDI FORMAT”/“DVI FORMAT” in the MAIN MENU “3D SETTING.”)

● Displayed left-justified when not in 3G SDI input or DVI input.

3 Detailed information on 3G SDI/HD SDI DUAL LINK input

● Displays the sampling structure/color space/pixel resolution of the signal format.

● Displayed when the 3G SDI or HD SDI DUAL LINK signal is input.

4 Setting of “MUTING”

● Displayed only when muting is activated (→ 5 on page 9).

5 Setting of FRAME SYNC.

● Only displayed when “FRAME SYNC.” in the MAIN MENU “3D SETTING” is set to “ON.” (→ on page 19)

Viewing 3D images

Basic 3D principle

This product is a 3D LCD Monitor which adopts the Xpol® circular polarizing method.

By having a filter of different polarization on every alternate scan line on the monitor, and projecting the left eye image (left circular polarization)

and the right eye image (right circular polarization) through the filters, users can enjoy a realistic three dimensional view by viewing the left and

right images simultaneously through the circular polarizing glasses.

As the left and right images are always displayed together on the screen, users can view flicker-free 3D images.

Compatible 3D format

The following 3D formats are supported: LINE BY LINE, SIDE BY SIDE HD, and SIDE BY SIDE SD.

LINE BY LINE

Displays image stripes

SIDE BY SIDE HD

Shrinks the size of the

SIDE BY SIDE SD

Tiles images for the left and

right eyes horizontally without

compressing. The horizontal

resolution remains unchanged,

but both sides of the screen are

displayed in black in 3D mode.

of the left and right

images line by line one

after another.

left and right images

by half and displays

them side by side.

The horizontal

resolution is divided

into two.

When viewing in 3D

● View 3D images at the recommended viewing distance (Recommended viewing distance : Approx. 65cm(25 5/8")).

● To view in 3D, change to a suitable mode before putting on the circular polarizing glasses to view the 3D images.

● Every individual will have a different experience when viewing 3D images. Viewing at a close distance may cause

disorders and discomfort.

● The 3D effects may differ when viewing the screen from different angles.

● Avoid viewing 3D images if you are in bad shape.

● Stop using the product and rest immediately if you experience eyestrain, dizziness, vomiting, headaches or any

other discomforts.

● If the symptoms persist even after resting, please consult a doctor.

● Take periodic breaks and rest even if you do not experience any discomfort. (Recommended viewing time : about 30

to 60 minutes).

● For users with past experiences of PSS (Photo Sensitive Seizure) or users with heart problems, please consult a

doctor before using this monitor.

● For children 6 and under still in the visual development stage, please consult a doctor and have an adult guardian

accompany the child.

● Though ghosting may occur when viewing 3D images, this is not due to a malfunction but to a characteristic of the

LCD panel.

Cautions on using the circular polarizing glasses

● Use the circular polarizing glasses only when viewing 3D images.

● Use the circular polarizing glasses provided or compatible with RealD™.

● For users who wear spectacles, cover the spectacles with the circular polarizing glasses.

● Do not use the circular polarizing glasses as sunglasses.

● Please consult a doctor if allergies appear on the areas that come into contact with the circular polarizing glasses.

NOTE

● When purchasing additional circular polarizing glasses, please select RealD™-compatible ones or contact the dealer where

you purchased your monitor.

● Though some faint black lines may appear on the screen when viewing 2D images, this is not due to a malfunction but to a

characteristic of the LCD panel.

•

Xpol® is a registered trademark of Arisawa Manufacturing Co., Ltd.

RealD™ is a trademark of RealD Inc. (US)

To view 3D images

To view in 3D, enter the 3D mode. The procedures differ between viewing existing 3D images and mixing L and R images taken by two cameras.

To view existing 3D images

View already 3D-processed images.

1 Input existing 3D images into the SDI IN 1/L, 2/R terminals or DVI-D terminal.

➔ Also compatible with DUAL LINK.

2 Press the INPUT SELECT button corresponding to the input images.

3 Press the 3D button.

4 Press the SELECT button to select a 3D format.

➔ Select a 3D format conﬁgured under “SDI FORMAT 1”/”SDI FORMAT 2” or “DVI FORMAT 1”/”DVI FORMAT 2” in the MAIN MENU

“3D SETTING.”

● Put on the circular polarizing glasses to view in 3D. Press the 3D button to enter the 3D mode that corrects

images for viewing with the circular polarizing glasses.

● 3D viewing is not available if the 3D images are not based on LINE BY LINE or SIDE BY SIDE.

● If the SIDE BY SIDE images in DVI input do not seem to be in the right position, adjust the image position under

“3D H POSITION” in the SET-UP MENU “H POSITION ADJ.” beforehand.

● If necessary, configure the settings such as the MAIN MENU “3D SETTING.”

● When inputting LINE BY LINE 3D images in a signal format that scales the screen vertically, use the 1:1 display

mode.

To view images taken by two cameras

Mix L and R images taken by two cameras and convert them to 3D images.

1 Input L images into the SDI IN 1/L terminal and R images into the SDI IN 2/R terminal.

➔

Input L and R images in the same format corresponding to the MIX mode.

(For 3G SDI LEVEL B Dual Stream, input into the SDI IN 1/L terminal. For 3G SDI LEVEL B DUAL LINK mapping, input into the SDI

IN 1/L and SDI IN 2/R terminals.)

2 Press SDI 1/L or SDI 2/R (INPUT SELECT button).

➔ In the case of 3G SDI LEVEL B Dual stream, press SDI 1/L.

3 Press the MIX button.

➔ Images in SIDE BY SIDE format.

4 Press the 3D button.

● Put on the circular polarizing glasses to view in 3D. Press the 3D button to enter the 3D mode that corrects

images for viewing with the circular polarizing glasses.

● If necessary, configure the settings such as the MAIN MENU “3D SETTING” or CAMERA ASSIST MENU.

Setting the CAMERA ASSIST MENU

This product is equipped with various camera rig adjustment assist functions for 3D viewing. Use the functions for camera adjustment in

shooting.

CAMERA ASSIST MENU

Menu Operations

1 Press the CAMERA ASSIST button.

➔ The CAMERA ASSIST MENU appears.

● Only works when the SDI input is selected and images available for the

MIX mode are input.

● When the CAMERA ASSIST button is pressed while “MARKER” is

displayed, “MARKER” disappears and the CAMERA ASSIST MENU appears.

2 Press the

button to select an item,

and then the button to proceed to the next screen.

● For some items, adjustments will be made by pressing

3 Press the CAMERA ASSIST button to finish the menu operation.

● Alternetively, press the MENU button to close the menu screen.

CAMERA ASSIST MENU

RIG SETTING

Depending on the stereo camera rig condition, configure the horizontal flip/vertical flip/180-degree rotation settings of an image.

● The settings are retained even when the CAMERA ASSIST MENU closes.

Half mirror

Parallel twin-flex

Half of the image is rotated 180 degrees.

Half of the image is flipped vertically.

Half of the image is flipped horizontally.

● Select “R-ROTATION.”

● Select “R-V-MIRROR.”

● Select “R-H-MIRROR.”

Setting value

OFF

Content

Does not rotate or flip the image

R-H-MIRROR

Horizontally flips images input into the SDI IN 2/R terminal

Vertically flips images input into the SDI IN 2/R terminal

Horizontally flips images input into the SDI IN 1/L terminal

Vertically flips images input into the SDI IN 1/L terminal

Rotates images input into the SDI IN 2/R terminal by 180 degrees

Rotates images input into the SDI IN 1/L terminal by 180 degrees

R-V-MIRROR

L-H-MIRROR

L-V-MIRROR

R-ROTATION

L-ROTATION

Vertical flip and 180-degree rotation delay the image by 2 frames. The other image will also be delayed and synchronized.

L image

R image

SPLIT

L image is displayed on the left of the SPLIT line, and R image on

the right. You can check the difference between the images from

the two cameras.

H line

SPLIT line

R image

H line

L image

LR SEQ.

Images for the left and right eyes are displayed alternately at

0.5-second interval.

● A marker appears on the upper part of the screen, which

distinguishes between L and R images.

L image: Upper left

0.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.

R image: Upper right

R SHIFT

L and R images are overlapped. You can move the R image

horizontally and check the difference between the images.

● While “R SHIFT” is active, the images are corrected according to

the check using the circular polarizing glasses.

L and R images not correspondent

L and R images correspondent

ANAGLYPH

L and R images colored red and blue separately are overlapped.

You can move the R image horizontally and check the difference

between the images.

INDIVIDUAL

Either L image or R image is displayed.

● Each time you press SELECT button, the picture changes in the

following order.

● A marker appears on the upper part of the screen, which

distinguishes between L and R images.

L image: Upper left

L image

R image

R image: Upper right

LR SWAP

L and R images are exchanged and then displayed. You can

exchange the images without repluging the terminals.

SDI IN

1/L 2/R

●

The setting is retained even when the menu closes. Note that L

and R images have been exchanged when the setting is set to

“ON.”

2/R 1/L

LR SWAP “OFF”

LR SWAP “ON”

POSITION knob/PUSH SEL. button

You can move the displayed SPLIT line/H line/R image (only in “R SHIFT” or “ANAGLYPH”) by turning

the POSITION knob.

To move right/up: Turn the POSITION knob clockwise.

To move left/down: Turn the POSITION knob counterclockwise.

To select a line to move: Press the PUSH SEL. button.

● Pressing and holding the PUSH SEL. button for 3 seconds or longer resets the lines and R image to the default positions.

● The intensities of the SPLIT and H lines can be changed in “L. INTENSITY” under the MAIN MENU “3D SETTING.” (→page 19)

Other 3D functions

SCOPE button/lamp

You can display the wave form monitor or vector scope, and compare and check the SDI IN 1/L and SDI IN 2/R input signals.

● Works in MIX mode. The operation to be performed differs in other modes. (→ page 9)

● Each time you press the SCOPE button, the display mode changes in the following order.

No display

ꢀ

Parallel wave form

monitor

Does not display the wave form monitor/vector scope.

Tiles the wave form monitors of the images input into the SDI IN 1/L and SDI IN 2/R terminals.

ꢀ

Parallel vector scope

Tiles the vector scopes of the images input into the SDI IN 1/L and SDI IN 2/R terminals.

ꢀ

Difference wave form

monitor

Select this to display the differential of the signals from the SDI IN 1/L and SDI IN 2/R terminals in

wave form monitor.

ꢀ

Difference vector

scope

Select this to display the differential of the signals from the SDI IN 1/L and SDI IN 2/R terminals in

vector scope.

Parallel wave form monitor

Parallel vector scope

Difference wave form monitor Difference vector scope

•

When the CAMERA ASSIST MENU “LR SWAP” is set to “ON”, L and R images of the parallel wave form monitor and vector scope are

exchanged and then displayed.

•

The positions of the wave form monitor and vector scope can be changed in “POSITION” under the MAIN MENU “SCOPE SETTING.”

The wave form monitor and vector scope are not displayed in “R SHIFT” or “ANAGLYPH” of the CAMERA ASSIST MENU.

The vector scope is not displayed when the input signals are RGB.

3D CURSOR button/lamp

When 3D is “ON”, the L and R lines measuring the visual difference between L and R images, and the pixels and percentage between the

lines, are displayed. The following two modes are available for the line display: “Cursor mode” and “Grid mode.”

● Each time you press the 3D CURSOR button, the line display mode changes in the following order.

No display

Cursor mode

Grid mode

● The information (→ page 10) and SCOPE are not displayed in “Cursor mode” or “Grid mode.”

● The positions of the pixels and percentage can be changed in “POSITION” under the MAIN MENU “INFORMATION.”

Cursor mode

The L, R, and H lines appear, which measure the visual difference.

● The H and L lines are fined dotted lines, and the R line a coarse dotted line. The selected line is displayed as a solid line.

L line (Group A)

R line (Group A)

Pixels/Percentage between L and R lines

H line (Group B)

H line (Group A)

(selected line)

R line (Group B)

L line (Group B)

● The line color changes when the line goes beyond “FAR LIMIT” or “NEAR LIMIT” under the MAIN MENU “3D SETTING.”

● The ratio of the difference between the L and R lines to the horizontal pixels appears in the percentage display.

● In the percentage display, “+” indicates the pop-up level (when the L line is placed on the right of the R line), and “–” the depth

(when the L line is placed on the left of the R line).

● In Cursor mode, the lines of the following two groups are displayed:

Group A: L line/R line/H line (Normal: Green / Over the LIMIT: Red)

Group B: L line/R line/H line (Normal: Magenta / Over the LIMIT: Orange)

• You can change a group to display by pressing the SELECT button. Each time you press the SELECT button,

the group changes as shown on the right.

• The line color turns to a color to be used when the LIMIT is exceeded when it goes beyond “FAR LIMIT” or

“NEAR LIMIT” under the MAIN MENU “3D SETTING.”

● You can move the L, R, and H lines by turning the POSITION knob.

To move right/up:

To move left/down:

Turn the POSITION knob clockwise.

Turn the POSITION knob counterclockwise.

To select a line to move: Press the PUSH SEL. button. Each time you press the button, the selected line changes in the following order.

L line

R line

H line

L+R line

• When you select a line while both Group A and B are displayed, the selection is performed for Group A first, and then for Group B.

• When both L and R lines are selected, the lines cannot be moved separately.

• Pressing and holding the PUSH SEL. button for 3 seconds or longer resets the displayed lines to the default positions.

Grid mode

The grid lines appear, which measure the visual difference.

Pixels/Percentage between the grid lines

Center window

● The following two types of the grid mode display are available: Normal display and Center window display.

You can change the display by pressing the SELECT button.

Normal display

Center window display

● The width of the grid line can be changed. Turning the POSITION knob enlarges/reduces the width based on the upper left of the screen as

the datum point.

To enlarge: Turn the POSITION knob clockwise.

To reduce: Turn the POSITION knob counterclockwise.

Reduce the width

Enlarge the width

● The ratio of the difference between the grid lines to the horizontal pixels appears in the percentage display.

● Pressing and holding the PUSH SEL. button for 3 seconds or longer resets the grid width to 100 pixels (default).

● When “L. INTENSITY” under the MAIN MENU “3D SETTING” is set to “LOW”, the grid line is displayed translucent.

Setting the menu (MAIN MENU/SET-UP MENU)

Menu Operations

MAIN MENU

SET-UP MENU

Item being

selected

1 Display the menu.

To display the MAIN MENU

➔ Press MENU button.

Operation

guide

To display the SET-UP MENU

➔ Press button while holding button.

2 Press

buttons to select an item, then press button.

MAIN MENU

Ex. When “MARKER” is

selected.

● For some items, adjustments will be made by pressing

Press buttons to select an item, then press

buttons to make adjustments.

4 Press MENU button to finish the menu operation.

● Pressing MENU button repeatedly deactivates the display of the menu.

Menu Transition Diagram

MAIN MENU

SDI FORMAT 1

SDI FORMAT 2

DVI FORMAT 1

DVI FORMAT 2

SINGLE IMAGE

FRAME SYNC.

FAR LIMIT

PICTURE FUNCTION

BACK LIGHT

APERTURE

APERTURE LEVEL

I/P MODE

sub menu

reset

3G SDI LEVEL B

SDI DUAL LINK

3D SETTING

AREA MARKER

MARKER ASPECT

SAFETY MARKER

SAFETY AREA

NEAR LIMIT

L. INTENSITY

FRAME

CENTER MARKER

LINE BRIGHTNESS

R-AREA MARKER

R-MARKER ASPECT

R-SAFETY MARKER

R-SAFETY AREA

ASPECT

LEVEL METER ch

BAR TYPE

REFERENCE LEVEL

OVER LEVEL

BAR BRIGHTNESS

PEAK HOLD

MARKER

BALANCE

E.AUDIO GROUP

LEVEL METER SETTING

AUDIO SETTING

SCOPE SETTING

SYNC FUNCTION

GAIN

SIZE

POSITION

TRANSPARENT

AUTO OFF

NO SYNC ACTION

DELAY TIME

LOW LATENCY

WAVE DISPLAY

WAVE FILTER

WAVE OVER LEVEL

MARKING

LEVEL

SET-UP MENU

FUNCTION SETTING

PICTURE SUB ADJ.

H POSITION ADJ.

WHITE BALANCE SET.

REMOTE SETTING

INFORMATION

sub menu POSI.

TALLY SELECT

SD4:3 LARGE

DIMMER

CONTRAST

BRIGHT

CHROMA

sub menu

reset

3D H POSITION

sub menu

reset

GAMMA

COLOR TEMP.

R DRIVE

G DRIVE

B DRIVE

R CUT OFF

G CUT OFF

B CUT OFF

sub menu

reset

SERIAL TYPE

PARALLEL TYPE

PIN1

PIN2

PIN3

PIN4

PIN5

PIN6

PIN7

POSITION

SOURCE ID

CONTROL LOCK

DVI INPUT SEL.

CHARACTER SET.

STATUS DISPLAY

TIME CODE

CRC ERROR

SUB HOUR METER

MODEL

SDI FORMAT

PIN8

all reset

VERSION

HOUR METER

● The menu automatically disappears in about 30 seconds after the previous operation.

● Some items may not appear on the menu depending on the input or the input signal.

● The items controlled by the MAKE system do not appear on the menu.

MAIN MENU

PICTURE FUNCTION

Setting for the picture quality.

Item

Content

Setting value

OFF, ON

APERTURE ^*1

APERTURE LEVEL ^*1

I/P MODE

Activates/deactivates the function at the level set in “APERTURE LEVEL.”

Simultaneously corrects the frequency characteristics of the RGB colors.

Selects a proper mode corresponding to the input picture.

01 – 10

NORMAL, CINEMA, FIELD

Display the sub menu which enables you to adjust the items of “PICTURE FUNCTION” while viewing the actual picture.

Restore the default settings for all the items in “PICTURE FUNCTION.”

sub menu

reset

Memorized for each input.

BACK LIGHT Setting value: -20 – +20

Adjusts the brightness of the display.

3G SDI LEVEL B Setting value: DS1, DS2

Selects the data stream from two HD SDI signals multiplexed when a 3G SDI LEVEL B signal comes in.

● The setting value will be invalid if a 3G SDI LEVEL B DUAL LINK signal is input.

SDI DUAL LINK Setting value: OFF, ON

Activates/deactivates the DUAL LINK function of SDI signals.

● “DUAL LINK” is displayed when the setting is set to “ON.” (→ “Status indication of DUAL LINK/3G SDI signal information” on page 11)

● Set this setting to “OFF” when an SDI signal other than DUAL LINK SDI is input.

3D SETTING

3D function settings.

Item

Content

Setting value

SDI FORMAT 1 ^*1

Set the first choice for 3D format in SDI input.

The setting values and features are as follows.

LbL-RL

LbL-LR

SbS-HD-LR

SbS-HD-RL

SbS-SD-LR

SbS-SD-RL

LbL-RL

LbL-LR

SbS-HD-LR

SbS-HD-RL

SbS-SD-LR

SbS-SD-RL

LINE BY LINE, the first line: R image

LINE BY LINE, the first line: L image

SIDE BY SIDE compressed horizontally, L image on the left

SIDE BY SIDE compressed horizontally, R image on the left

SIDE BY SIDE not compressed, L image on the left

SIDE BY SIDE not compressed, R image on the left

• When the 3D mode is “ON” in 3D input, pressing the SELECT button switches between

“FORMAT1” and “FORMAT2.”

SDI FORMAT 2 ^*1

DVI FORMAT 1 ^*1

DVI FORMAT 2 ^*1

Set the second choice for 3D format in SDI input.

Set the first choice for 3D format in DVI input.

Set the second choice for 3D format in DVI input.

SINGLE IMAGE ^*1

Select a channel to be displayed when the 3D mode is “ON.”

OFF

LEFT

RIGHT

OFF

LEFT

RIGHT

Normal 3D (Left and right images)

L image only

R image only

Synchronize the left and right input signals by forcibly locking the SDI IN 2/R input for the SDI IN 1/L OFF

FRAME SYNC.

input in MIX mode.

• The time base cannot be corrected on this product. To take 3D images strictly, perform

GENLOCK on the shooting device, and set this setting to “OFF.”

• When “ON” is selected, the playback proceeds one frame later than when “OFF” is selected.

Set the limit of the depth in Cursor mode of “3D cursor.”

• The line color changes when the difference between the vertical lines goes beyond the

specified range.

Set the limit of the pop-up level in Cursor mode of “3D cursor.”

• The line color changes when the difference between the vertical lines goes beyond the

specified range.

Set the intensity of lines displayed in the CAMERA ASSIST MENU and “3D cursor.”

• When “LOW” is selected, the grid lines are displayed translucent in Grid mode of “3D

cursor.”

– 0.1% – – 4.0%

+01% – +20%

FAR LIMIT

NEAR LIMIT

L. INTENSITY

HIGH

LOW

Works when the MIX mode is “OFF” or invalid.

Menu Configuration (cont.)

ASPECT Setting value: 4:3, 16:9

Set the aspect ratio of images.

● Not activate when picture is displayed in the 1:1 mode.

MARKER^*1*2

Settings for marker functions.

Item

Content

Setting value

1/2 AREA MARKER ^*3

Activate/deactivate the area marker and select the style of it.

The setting values and features are as follows.

OFF

LINE

HALF

HALF+L

BLK.

OFF

LINE

HALF

Deactivate the marker.

Displays the area with an outline.

The area outside the specified aspect ratio of the screen is

displayed at 50% transparency.

BLK.+L

HALF+L

BLK.

The area of the specified aspect ratio of the screen is

indicated by an outline, and the area outside of that is

displayed at 50% transparency.

The area outside the specified aspect ratio of the screen is

black. Only the portion of the picture within the designated

area is displayed.

The area of the specified aspect ratio of the screen is

indicated by an outline, and the area outside of that becomes

black so that only the area inside the line is displayed.

BLK.+L

MARKER ASPECT ^*3

SAFETY MARKER

Select the aspect ratio of the area marker.

4:3, 14:9, 13:9, 2.35:1,

1.85:1, 1.66:1

Activate/deactivate the safety marker and select the style of it. *

OFF, LINE, HALF, HALF+L,

BLK., BLK.+L

Adjust the area of the safety marker.

80% – 100%

OFF, ON

SAFETY AREA

FRAME

Displays/hides the frame indicating the area of the specified aspect ratio.

Displays/hides the marker indicating the center position of the picture.

Adjust the brightness of the marker.

OFF, ON

CENTER MARKER

LINE BRIGHTNESS

2/2 R-AREA MARKER ^*3

HIGH, LOW

Display/Hide the area marker and select a type. *

OFF, LINE, HALF,

HALF+L,

BLK., BLK.+L

R-MARKER ASPECT ^*3

R-SAFETY MARKER

Select the aspect ratio of the area marker.

4:3, 14:9, 13:9, 2.35:1,

1.85:1, 1.66:1

Activate/deactivate the safety marker and select the style of it. *

OFF, LINE, HALF,

HALF+L,

BLK., BLK.+L

Adjust the area of the safety marker.

80% – 100%

R-SAFETY AREA

● The area marker or the safety marker is displayed by using AREA MARKER or SAFETY MARKER button, or external control.

● Select either non-“R-” items or “R-” items to activate by using external control (→ “External control” on page 26).

● When a picture is displayed in 4:3 aspect ratio, the safety marker for the 4:3 area is displayed.

● To display the safety marker for the area of a picture displayed in 16:9 aspect ratio, hide the area marker.

Memorized for each input.

Not displayed in 1:1 mode or when “SD4:3 LARGE” under the SET-UP MENU “FUNCTION SETTING” is set to “ON” and 4:3 format signals

are input.

Displayed only when picture is displayed in 16:9 aspect ratio.

The setting values are the same as that of “AREA MARKER.”

AUDIO SETTING

Settings for the audio output balance, EMBEDDED AUDIO signals and level meter.

Item

Content

Setting value

Adjust the balance between the right and left speakers.

L5 – L1, 0, R1 – R5

BALANCE

E.AUDIO GROUP ^*1

Select the audio channel group of the EMBEDDED AUDIO signals.

The setting values and selectable audio channels of EMBEDDED AUDIO signals are as follows.

1-2G

1-3G

1-2G

1-3G

Channel 1/2/3/4/1+2/3+4/1 – 4 (1G)

Channel 5/6/7/8/5+6/7+8/5 – 8 (2G)

Channel 1/2/3/4/5/6/7/8/1+2/3+4/5+6/7+8/1 – 4 (1G)/5 – 8 (2G)/1 – 8 (1G+2G)

Channel 9/10/11/12/9+10/11+12/9 – 12 (3G)

Channel 1/2/3/4/5/6/7/8/9/10/11/12/1+2/3+4/5+6/7+8/9+10/11+12/

1 – 4 (1G)/5 – 8 (2G)/9 – 12 (3G)/1 – 8 (1G+2G)/1 – 12 (1-3G)

• G means GROUP

Adjust the level meter display for the EMBEDDED AUDIO signals.

LEVEL METER SETTING

Example of the level meter display —Level meter position and audio channels

Ex.: When “LEVEL METER ch” is set to “LINE” and “BAR TYPE” is set to “3COLORS”

OVER LEVEL

REFERENCE LEVEL

Red

Yellow

Green

• The level meter with no audio signal input is displayed in white for “3COLORS”, and in gray for “W.100.”

• You can select the position of the level meter display—top or bottom of the screen (→ “POSITION” in

“INFORMATION” on page 24).

• When “PEAK HOLD” is set to “ON,” the maximum level meter value will remain displayed for a set period

of time.

Select how the audio channels are displayed on the level meter.

OFF

LINE

DIVIDE

– LEVEL METER ch

– BAR TYPE

LINE

DIVIDE

Displays the channels 1 – 6 at the left of the screen and 7 – 12 at the right.

Displays the odd channels at the left of the screen and the even channels at

the right.

Select the color of the level meter display.

3COLORS

W.100

3COLORS

W.100

Coloring for each level

White

Select the standard input level indicated on the level meter.

−20dB, −18dB

– REFERENCE LEVEL

– OVER LEVEL

Select the input level’s lower limit indicated in red for the “3COLORS” display.

−10dB, −8dB,

−6dB, −4dB, −2dB

Select the brightness of the level meter.

LOW, HIGH

OFF, ON

– BAR BRIGHTNESS

Activates/deactivates the peak hold function of the level meter.

– PEAK HOLD

Memorized for each input. In MIX mode, the setting only applies to audio signals input into SDI IN 1/L.

Menu Configuration (cont.)

SCOPE SETTING^*1

Configure the settings for the wave form monitor and vector scope.

Item

Content

Setting value

–10 – +10

Adjust the input gain level.

Set the window size.

Select the window position.

GAIN

SIZE ^{*2 *3}

POSITION ^*2

NORMAL, LARGE

1 (Lower right), 2 (Lower left)

3 (Upper left), 4 (Upper right)

TRANSPARENT ^*3

Make the background of the window translucent.

OFF

Translucent

Normal

Set the function to turn off the window automatically 15 minutes after displayed.

Select a wave form to be displayed for the wave form monitor.

ON, OFF

AUTO OFF

WAVE DISPLAY

Y, Pb, Pr (HD signal)

Y, Cb, Cr (SD signal)

R, G, B (RGB signal)

FLAT (No filter)

Turn on/off the lowpass filter to put over the input wave form data.

WAVE FILTER

LOWPASS

Set the over levels of the luminance signals (Y) and RGB signals.

WAVE OVER LEVEL

Example of the wave form monitor

Example of the vector scope

Ex.: When the luminance signal is Y, “MARKING” is set to “ON” and “LEVEL” is set to Ex.: When the color bar is

“080” displayed

Red

White

Image signals

Start

End

• The wave form color of signals over the value specified in “LEVEL” turns red.

• The display differs depending on the input signal or the “WAVE DISPLAY”

setting.

Turn on/off the function to change the wave form color of signals over the value

specified in “LEVEL.” (→ below)

OFF, ON

070 – 109

– MARKING

– LEVEL

Adjust the lower limit for the over level.

The wave form monitor is not displayed when the input signals are DVI (input from a computer). The vector scope is not displayed when the

input signals are RGB.

When “SIZE” is set to “LARGE,” the window is displayed in the center of the screen regardless of the “POSITION” setting.

Not displayed in MIX mode or when the CAMERA ASSIST button is “ON.”

SYNC FUNCTION

Settings for the synchronization with signals.

Item

Content

Setting value

OFF

Select the screen status when no signal is coming in.

NO SYNC ACTION

STANDBY

P.SAVE

GRAY B.

STANDBY

P.SAVE

GRAY B.

The monitor is off (on standby)

Power save mode

Gray screen

Select the period until the screen status changes as selected in “NO SYNC ACTION” after

signals stop coming in.

30sec., 5min., 15min.

DELAY TIME

Activates/deactivates the function to shorten the time taken to display the picture.

• If the picture is not displayed steadily while “ON” is selected, select “OFF.”

• While “ON” is selected, the displayed picture may become unstable when an

operation using buttons on the front panel or the menu is performed, or when the

signal format changes.

OFF

LOW LATENCY

● When setting “NO SYNC ACTION” to “GRAY B.,” the screen color changes to gray and the power consumption of the back light is saved by

half. Selecting “P.SAVE” (power save mode) saves more power consumption by turning off the back light.

● In the initial setting, “NO SYNC ACTION” is set to “P.SAVE”, and “DELAY TIME” set to “15min.” Change the settings if necessary. (U.S.A. only)

SET-UP MENU

FUNCTION SETTING

Configure the sub menu display, the lighting color of the tally lamp, the size of images, the brightness of the button lamps.

Item

Content

Setting value

LOWER1

UPPER1

LOWER2

UPPER2

sub menu POSI. Select the contents and displaying position of “sub menu.”

The setting values and features are as follows.

LOWER1

UPPER1

LOWER2

UPPER2

Displays the current setting and adjustment bar at the lower part of the screen.

Displays the current setting and adjustment bar at the upper part of the screen.

Displays the current setting at the lower part of the screen.

Displays the current setting at the upper part of the screen.

• The adjustment bar is not displayed for some items.

Select the color of the tally lamp.

GREEN, RED

TALLY SELECT

SD4:3 LARGE

Selects the picture size when the input signal format is 4:3.

The setting values and features are as follows.

OFF

Matches the vertical picture size to the number of pixels.

Matches the horizontal picture size to the horizontal size of the screen.

Select the intensity of the button lamps.

NORMAL, DARK

DIMMER

PICTURE SUB ADJ.

Configure the standard level of image adjustment.

Item

Content

Setting value

– 20 – +20

CONTRAST ^*1

BRIGHT ^*1

CHROMA ^*1

sub menu

reset

Adjust the standard level for the contrast adjusted with the CONTRAST knob on the front panel.

Adjust the standard level for the brightness adjusted with the BRIGHT knob on the front panel.

Adjust the standard level for the chroma adjusted with the CHROMA knob on the front panel.

Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.” while viewing the actual picture.

Restore the default settings for all the items in “PICTURE SUB ADJ.” (You cannot select items to reset.)

Memorized for each input.

H POSITION ADJ.

Adjust the center position of SIDE BY SIDE images.

Item

Content

Setting value

– 032 – +031

Display the center line to adjust the horizontal image position.

• The setting will be valid when the 3D mode is “ON” and MIX mode is “OFF” or invalid.

3D H POSITION

Display the sub menu which enables you to adjust the items in “H POSITION ADJ.” while viewing the actual picture.

Restore the default settings for all the items in “H POSITION ADJ.”

sub menu

reset

WHITE BALANCE SET.

Selects the gamma correction value, color temperature and adjusts the drive level and cutoff point of each color (R/G/B).

Item

Content

Setting value

Select a gamma correction.

2.2 (equivalent to γ2.2), 2.35 (equivalent to γ2.35)

2.45 (equivalent to γ2.45), 2.6 (equivalent to γ2.6)

9300K, 6500K, USER

GAMMA

Select the color temperature.

COLOR TEMP.

• The color temperature is corrected when the 3D mode is “ON.”

Adjust the drive level of each color (red, green, and blue).

MIN – 000 – MAX (in 256 grades)

R DRIVE

G DRIVE

B DRIVE ^*1

R CUT OFF

G CUT OFF

B CUT OFF ^*1

Adjust the cutoff point of each color (red, green, and blue).

Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.” while viewing the actual picture.

sub menu

reset

Restore the default settings for the drive levels and cutoff points of the selected color temperature. (You cannot select

items to reset.)

Memorized for each color temperature.

Menu Configuration (cont.)

REMOTE SETTING (→ “External Control” on pages 26)

Settings for the external control.

Item

Content

Setting value

Select the input terminal used for external control by serial

communication.

RS232C

RS485

SERIAL TYPE

Select the external control method for the MAKE/TRIGGER terminal.

MAKE, TRIGGER, SET

PARALLEL TYPE

Assign the control functions to the pins of the MAKE/TRIGGER terminal.

• Assign a function to each pin terminal by selecting “SET” in

“PARALLEL TYPE” mentioned above.

PIN1

PIN2

PIN3

PIN4

PIN5

→ <Functions controlled by the

MAKE/TRIGGER system> on page

27.

The functions are assigned for “PIN6” – “PIN8” and you cannot change the

assignment of these functions.

PIN6

PIN7

PIN8

→ “Using the MAKE/TRIGGER

system” on page 26

INFORMATION

Settings for the information display of the monitor.

Item

Content

Setting value

UPPER

POSITION

Select the position to show the information display (→ “On the

LOWER

Information Display” on page 10).

Select whether the name assigned in “CHARACTER SET.” is displayed on

the screen (→ “On the Information Display” on page 10).

OFF

SOURCE ID

• When “AUTO” is selected, the display color synchronizes with the

color of the tally lamp while the tally lamp is lit.

AUTO

CHARACTER SET. ^*1

Assign a name to each video source as you like (10 characters at maximum).

You can also enter a name using the RS-232C system.

Setting of “CHARACTER SET.”

Change the input to one that you want to assign a video source name

for.

Select “CHARACTER SET.”

Press the

buttons to select a character to enter at first.

● Each time you press the button, the characters change in the

following order. Press button to reverse the order.

space

Press button to move the arrow to the next space.

● The characters entered before moving the arrow are memorized.

Repeat steps 3 and 4 (10 characters at maximum).

Press MENU button to store the name.

Select whether the status of the current input and the setting of MUTING

AUTO, OFF, ON

STATUS DISPLAY

are displayed on the screen (→ “On the Status Display” on page 11).

Select the type of the TIME CODE display.

VITC , LTC , D-VITC

TIME CODE

CRC ERROR

Select whether the CRC error indication for the input HD SDI signal is

displayed on the screen (→ “On the Information Display” on page 10).

OFF

Display the hours of use (unit: hour).

You can reset this item.

SUB HOUR METER

Display the model name of the monitor.

Display the version of the monitor.

MODEL

VERSION

Display the total hours of use (unit: hour).

HOUR METER

This item is used for maintenance of the monitor. You cannot reset this item.

Memorized for each input.

Ancillary time code

CONTROL LOCK Setting value: OFF, VOL.LOCK, ALL LOCK

Settings for disabling the buttons on the front panel.

● The following operations are not available when “VOL.LOCK” is selected.

– VOLUME adjustment knob

– Picture adjustment knob

● The “ALL LOCK” function disables to control the buttons on the front panel. But following operations are available.

– Turning on/off (on standby) the monitor.

– Press the button and button to display the SET-UP MENU, and set “CONTROL LOCK” to “OFF.”

– Operate this product by external control.

When you perform operations other than the above, “ Control lock on!” appears.

DVI INPUT SEL. Setting value: AUTO, COMPO., RGB, PC

Settings for formats of signals input into the DVI-D (HDCP) terminal.

● Automatically distinguishes signals when set to “AUTO.” (Normally, select “AUTO”)

● Select “COMPO.”, “RGB” or “PC” when the picture is not displayed correctly with “AUTO.”

● DVI-D input of the monitor is compatible with HDCP.

SDI FORMAT Setting value:AUTO, MS1YCbCr, MS2YCbCr,

MS3YCbCr, MS4YCbCr, MS2 RGB, MS3 RGB, 3G-B-DS

Settings for formats of signals for 3G SDI/HD SDI DUAL LINK input.

● Automatically distinguishes signals when set to “AUTO.” (Normally, select “AUTO”)

● If the picture is unstable with “AUTO”, select the setting value according to the input signal format.

● When “AUTO” is not selected, “M” appears in the status display.

all reset

Restores all the settings and adjustments of the monitor to the default.

● “HOUR METER” and the settings done by using the adjustment knobs on the front panel will not be reset.

● If reset while the AC power is on, the monitor turns off (standby), and then turns on automatically.

● If reset while the DC power is on, the monitor turns off (standby).

External control

About the external control

Using the MAKE/TRIGGER

system

This monitor has three external control terminals.

● MAKE/TRIGGER terminal (RJ-45): The following external control

systems are available.

The MAKE/TRIGGER terminal is configured as follows.

You can assign a function to each pin terminal in “REMOTE SETTING.”

(→ “PIN1, PIN2, PIN3, PIN4, PIN5” in “PARALLEL TYPE” on page 24)

1 MAKE (make contact) system:

Controls the monitor by short-circuiting the corresponding pin

terminal to the GND pin terminal, or disconnecting (opening) it.

● You cannot change the functions assigned to the pin terminals

from 6th to 8th.

2 TRIGGER (trigger) system:

Controls the monitor by sending the pulse signal

instantaneously to the corresponding pin terminal.

→ “Using the MAKE/TRIGGER system” on the right.

Pin No.

Pin name

PIN1

PIN2

PIN3

PIN4

PIN5

TALLY

● RS-485 terminal (RJ-45): Controls the monitor with the RS-485

system (→ “Using the serial communication” on page 28).

● RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-

232C system (→ “Using the serial communication” on page 28).

Set the following items of “REMOTE SETTING” in SET-UP MENU

according to the external control terminal and control system (→

“SERIAL TYPE,” “PARALLEL TYPE” on page 24).

This is a female

terminal.

ENABLE

GND

The settings of this unit

Control

terminal

“SERIAL “PARALLEL

TYPE”

Control system

The 6th pin terminal controls turning on or off the tally lamp

(available to control even when the 7th pin terminal is invalid).

The 7th pin terminal makes the external control valid/invalid.

Make sure to control the terminal by the MAKE system.

TYPE”

setting

—

MAKE

MAKE/

MAKE

TRIGGER

terminal

—

TRIGGER

To assign the functions to the pin terminals

RS-485

terminal

RS485

—

RS-485

For the operation procedure, see page 18.

Serial

Select “REMOTE SETTING” on the SET-UP MENU.

Set “PARALLEL TYPE” to “SET.”

Select a pin name (“PIN1” – “PIN5”) for which you want

to assign a function, then select the function you want

to assign.

communication

RS-232C

terminal

RS232C

RS-232C

For a monitor connected to a personal computer etc, select

the terminal the equipment is actually connected to. For other

monitors, select “RS485.”

Control priority is as follows.

MAKE > TRIGGER = serial communication = buttons and menu on

the monitor

● You can use external control even when “CONTROL LOCK” is set to

“VOL.LOCK” or “ALL LOCK.” (→ page 25)

● When the monitor is off (on standby), external control is not

available. But certain external controls (starting/terminating

communication, turning on the monitor) are available through the

serial communication. (→ page 29)

For the selectable functions, see the table on page 29.

Operation of the external control

Set “PARALLEL TYPE” of “REMOTE SETTING” to “MAKE”

or “TRIGGER” in the SET-UP MENU.

Short-circuit the 7th pin terminal (ENABLE) to the

8th pin terminal (GND) so that the monitor can be

controlled by the external control.

When the “MAKE” system is selected:

You can control the monitor by a personal computer or dedicated

Operate each function by short-circuiting the

corresponding pin terminal to the 8th pin terminal

(GND) or opening it.

controller .

● “Using the MAKE/TRIGGER system” on the right.

The controller is not commercially available. Consult your dealer if

When the “TRIGGER” system is selected:

Operate each function by pulse control, that is short-

circuiting the corresponding pin terminal to the 8th pin

terminal (GND) for about 1 second and opening it.

you need it.

● When changing the input with MAKE system, only one pin terminal

must be short-circuited. (Other pin terminals must be opened.)

● When selecting the “TRIGGER” system, you can operate only one

function at a time. Operate the functions one by one.

PC, etc.

RS-485

OUT

RS-485

OUT

RS-485

RS-485 IN

RS-232C

RS-485

OUT

● For the details, see page 28.

Display

TALLY SEL

Functions to be controlled

Selects the color of the tally lamp

Opening

Green

Invalid

Off

Short-circuiting

Red

Valid

SDI 1/L

Changes the input to “SDI 1/L”

Changes the input to “SDI 2/R”

Changes the input to “DVI”

SDI 2/R

DVI

Activates/Deactivates the 3D mode

Activates/Deactivates the MIX mode

MIX

Off

3D FORMAT

3G-B.DS

DUAL LINK

MARKER

FRAME

3D format 1/3D format 2 change

FORMAT1

DS1

FORMAT2

DS2

Selects the data stream of “3G SDI LEVEL B”

Turns on or off “SDI DUAL LINK”

Off

Displays the area and safety markers

Indication of the area of the specified aspect ratio

The center marker indication

Off

C.MARKER

MARK.SEL

ASPECT

1:1

Off

Selects the items of “MARKER”

Non-“R-” items

4:3

“R-” items

16:9

Changes the aspect ratio

Displays in 1:1 mode

Off

STATUS

L.METER

TIME CODE

SOURCE ID

PARA.WFM

PARA.VS

BAL.WFM

BAL.VS

Status display

→ “On the Status Display” on page 11

Audio level meter display

Time code display

Off

→ “SOURCE ID” in “INFORMATION” on page 24

Displays the wave form monitor (Normal or Parallel)

Displays the vector scope (Normal or Parallel)

Displays the wave form monitor (Normal or Difference)

Displays the vector scope (Normal or Difference)

Color off

COLOR OFF

SCR CHECK

I/P MODE

MUTING

DIMMER

−−−

Color

Monochrome

Screens check

*10

Change a mode according to the input picture

Muting on/off

Off

NORMAL

—

DARK

—

Change the intensity of the button lamps

No function

The 3D format changes in the same way as the SELECT button pressed in 3D mode.

Selects which functions in “MARKER” are activated, non-“R-” items or “R-” items (→ “MARKER” on page 20).

Displays the information shown when INPUT SELECT button of the current input is pressed (→ “On the Status Display” on page 11). While

controlling with the MAKE system, the information is displayed only at the moment of short-circuiting.

While controlling with the MAKE system, the level meter is switched between displayed (short-circuiting) and hidden (opening). When

“LEVEL METER ch” is set to “OFF,” the level meter is not displayed (“NO EFFECT” appears). While controlling with the TRIGGER system, the

pattern of the audio channel display is switched.

While controlling with the MAKE system, the available set-up options will be the setting value currently selected in “SOURCE ID” (“ON” or

“AUTO” [short-circuiting]) and “OFF” (opening). While controlling with the TRIGGER system, uses the same set-up option as those in the SET-

UP MENU (→ “SOURCE ID” in “INFORMATION” on page 24).

While controlling with the TRIGGER system, the display mode changes in the same way as for the normal SCOPE function. (→ e on page 9)

While controlling with the MAKE system, the displayed (short-cirtuiting)/hidden (opening) operations are performed as follows regardless of

the MAIN MENU “AUTO OFF” setting:

[PIN 1] − [PIN 5] settings

PARA.WFM PARA.VS BAL.WFM

Priority when the settings a re configured simultaneously

Display

Invalid

BAL.VS

Wave form Vector Wave form Vector

Wave form monitor > Vector scope

monitor

Parallel

scope

monitor

scope

MIX

mode

Parallel Difference Difference

Parallel wave

form monitor

Difference wave

form monitor

Parallel

vector scope

Difference

vector scope

Valid wave form vector wave form vector

monitor scope monitor scope

While controlling with the MAKE system, the screen is switched between normal screen (opening) and blue screen (short-circuiting). While

controlling with the TRIGGER system, the screen changes in the same way as when pressing SCREENS CHECK button (→ w on page 9).

Must be controlled with the TRIGGER system. The mode changes in the order of “NORMAL” → “CINEMA” → “FIELD” (This function cannot be

controlled with the MAKE system).

*10

● You cannot assign the same function to different pin terminals.

● The TRIGGER system switches each function by short-circuiting the pin terminal for about 1 second and opening it.

External Control (cont.)

Using the serial communication

You can control the monitor from a personal computer etc. via the RS-485 or RS-232C terminal.

● Consult your dealer for the details of the external control specification.

Terminal

specification

Input terminal

RS-485

RS-232C

Cable

Communication specifications

A straight LAN cable

Baud Rate: 4800 bps

Data Bits: 8 bits

Parity: No parity

A straight cable with a D-sub 9-pin connector (male

for the monitor, female for the personal computer

etc.)

→ See below

Stop Bits: 1 bit

Flow Control: No control

Communication Code: ASCII Code

Pin No.

IN terminal signal

TXD +

TXD −

RXD +

OUT terminal signal

TXD +

TXD −

RXD +

This is a female terminal.

RXD −

GND

RXD −

GND

Pin No.

Signal

RXD

TXD

GND

RTS

CTS

This is a female terminal.

● The 7th terminal and the 8th terminal are connected.

All commands consist of the following segments.

Header

Monitor ID

Command ID

Function

Data

Cr (0Dh)

On Header

“!”

“?”

“@”

Operation commands from the personal computer, etc. (→ <Basic command list> on page 29)

Reference commands from the personal computer, etc.

Status returns from the monitor

To start communication, send the connection command from the personal computer etc. To terminate the communication, send the

termination command from the personal computer etc.

Example of communication procedures

1 Starting the communication: connection command (!00BCN1Cr)

Monitor

2 Monitor’s status (@00BOKCr)

3 Selecting “SDI 1/L” input (!00BINACr)

4 Monitor’s status (@00BOKCr)

PC, etc.

5 Terminating the communication: termination command (!00BCN0Cr)

6 Monitor’s status (@00BOKCr)

No.

Commands

Functions

Starts communication (connection)

Terminates communication (termination)

Assigns the control ID

Data

No data

01 – 99

No data

00: Hide

Initializes the control ID

Displays/hides the ID

01: Display

00: Hide

Flashes/hides the selected ID No. of the monitor

Displays the MAIN MENU/Quits the menu operation

01: Display

No data

Moves the cursor downward (

)

P Cr

O W

Makes setting/adjustment (

Displays the SET-UP MENU

Turns on the monitor

)

Turns off the monitor (on standby)

Selects “SDI 1/L” input

Selects “SDI 2/R” input

Selects “DVI” input

Displays the status *

00: Off

01: On

A M U

Turns muting on/off

00: 4:3

01: 16:9

Changes the aspect ratio

Cr Configures POSITION settings

Configures PUSH SEL. settings

Operates the SELECT keys

−999 – +999

00: Change selection,

01: Reset the position

No data

00: Off

01: Cursor mode

02: Grid mode

Changes 3D cursor mode

00: Off

01: On

Changes 3D mode

A M

Displays the CAMERA ASSIST MENU

Changes MIX mode

No data

00: Off

01: On

● “Cr” is 0Dh.

● The commands for starting communication (connection) (No. 1), terminating communication (termination) (No. 2), and turning on the

monitor (No. 13) can be used while the monitor is off (on standby).

Enter the monitor’s ID for “**.” The initial setting of the monitor’s ID is “00.” When connecting several monitors, “00” is a command for

controlling all monitors at once.

Enter the appropriate data to “xx.”

Displays the information shown when the INPUT SELECT button currently lit is pressed (→ “On the Status Display” on page 11).

Troubleshooting

Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the

monitor and consult an authorized dealer or service center.

Symptom

Probable cause and corrective action

button to turn it on.

● Plugs should be firmly inserted.

● Turn on the AC power switch on the back of this product.

Page

● Press the

Cannot turn on the unit.

● If you do not turn on the monitor by pressing the

button while the DC power is turned

on, disconnect the DC connector, set up the DC power within the operating range, and then

connect the connector again.

● Select the correct input using the INPUT SELECT buttons.

● Connect the signal cable firmly.

● Turn on the power of the connected component and set the output correctly.

● Check whether the input signal format is acceptable on the monitor.

—

No picture with the power on.

33, 34

● Adjust the volume level.

● Deactivate the muting function.

No sound.

● Connect the signal cable firmly.

● Turn on the power of the connected component and set the output correctly.

—

● Input a signal compatible with the unit.

11, 33,

“Out of range” appears.

● Select the correct input using the INPUT SELECT buttons.

● Connect the signal cable firmly.

● Turn on the power of the connected component and output video signals. Or, check whether

the video output of the component (video output setting of the VCR or graphic board of the

computer) is set correctly.

—

“NO SYNC” appears.

● Adjust each picture adjustment knob on the front panel or adjust the items of “PICTURE SUB

ADJ.” in the SET-UP MENU. Or, perform “reset” in “PICTURE SUB ADJ.”

● Check whether the setting of COLOR OFF or SCREENS CHECK buttons are appropriate.

● Adjust the items of “WHITE BALANCE SET.” in the SET-UP MENU. Or, perform “reset” in “WHITE

BALANCE SET.”

8, 23

Wrong color, no color.

● Adjust the picture contrast or brightness by using the adjustment knobs on the front panel.

Or, adjust “CONTRAST” or “BRIGHT” of “PICTURE SUB ADJ.” in the SET-UP MENU.

● Check whether the setting of 1:1 is appropriate.

● Check “ASPECT” of the MAIN MENU, and “ SD4:3 LARGE “ under the SET-UP MENU “FUNCTION 20, 23

8, 23

The picture becomes blurred.

Wrong picture position, wrong

picture size.

For some signals, the picture

cannot be displayed fully in the

effective screen area. There is no

sure method to solve this problem.

SETTING.”

● Check whether the input signal format is acceptable on the monitor.

33, 34

● The items which are not available for the current input or the current input signal are not

displayed on the menu. Change the input or the input signal.

● The items controlled by the MAKE system do not appear on the menu.

● Set “CONTROL LOCK” in the SET-UP MENU to “OFF.”

● You cannot use the buttons for the items controlled by the MAKE system. Disable the external 26, 27

—

Some items do not appear on

the menu.

Buttons on the monitor do not

work.

control.

● Press the 3D button to enter the 3D mode.

Press the SELECT button to change the 3D viewing format (when inputting existing 3D images).

● Set the 3D format compatible with input images in “SDI FORMAT 1/SDI FORMAT 2” or “DVI

FORMAT 1/ DVI FORMAT 2” under the MAIN MENU “3D SETTING.”

● Press the MIX button to enter the MIX mode.

9, 13

●

3D viewing is not available.

Cannot enter the MIX mode.

9, 13

—

● Input L and R images in the same format compatible with the MIX mode.

● Input 3G SDI LEVEL B Dual Stream into the SDI IN 1/L terminal.

● Set “FRAME SYNC.” under the MAIN MENU “3D SETTING” to “ON” or “OFF.”

The image is distorted or cannot

be synchronized in MIX mode.

The following are not malfunctions.

● When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has changed.

Though the remaining picture will disappear after a while, there may be a case that it remains for a long period

depending on the length of time the still image was displayed for. This is due to the characteristics of the LCD

display and is not a malfunction.

● Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays, and not a

problem. The LCD display is built with very high precision technology; however, be aware that a few pixels may be

missing or constantly lit.

● The following symptoms are problems only when pictures or sounds are not played back normally.

● A slight electric shock occurs when you touch the monitor.

● The top and/or rear panel of the monitor becomes hot.

● The monitor emits a cracking noise.

● The monitor emits a mechanical noise.

Self-check program

This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes troubleshooting easier. Whenever a

problem occurs, one or some of the INPUT SELECT lamps will flash. If this happens, follow the steps below and contact your dealer to resolve the

problem.

When the screen goes blank, and one or some of the INPUT SELECT lamps (SDI 1/L, SDI 2/R, DVI) on the front control panel start flashing...

1 Check which lamps are flashing.

2 Press

button to turn off (on standby) the monitor.

3 Turn off the AC power switch on the rear panel.

4 Disconnect the AC power cord from the AC outlet.

5 Contact your dealer with the information about which lamps were flashed.

● If you turn on the monitor soon after turning it off (or after a short-term power failure), the INPUT SELECT lamps may flash and no image may

be displayed.

When this happens, turn off power and wait at least 10 seconds before turning on the monitor again.

If the INPUT SELECT lamps do not flash, you can use the monitor as normal.

Specifications

General

Model name

Type

DT-3D24G1

MULTI FORMAT 3D LCD MONITOR

Type 24 wide format

16:10

Screen size

Aspect ratio

Compliant video signal format

Format

→ “Available signals” on page 33

3G SDI

DUAL LINK HD SDI

HD SDI

SMPTE424M/SMPTE425M

SMPTE372M

BTA S-004C, SMPTE292M

SD SDI

ITU-R BT.656:

SMPTE259M:

525/625

525

EMBEDDED AUDIO

SMPTE299M, SMPTE272M

Internal speaker: 1.0 W + 1.0 W

Audio output

Operating temperature: 5°C – 35°C (41°F – 95°F)

Operation environment

Operating humidity: 20% – 80% (non-condensing)

(Slightly variable depending on ambient conditions for installation.)

AC 120 V/AC 220 – 240 V, 50 Hz/60 Hz, or DC 24 V (Voltage range: DC 23.3 V − DC 25.5 V)

Power requirements

Rated current

1.15 A (AC 120 V)

0.67 A (AC 220 – 240 V)

4.8 A (DC 24V)

Width: 564 mm (22 1/4˝)

Height: 448.6 mm (17 3/4˝)

Depth: 243 mm (9 5/8˝)

(with the stand)

564 mm (22 1/4˝)

408 mm (16 1/8˝)

99 mm (4˝)

External dimensions (excluding

protruding parts)

(without the stand)

12.0 kg (26.4 lbs) (with the stand) 9.1 kg (20.0 lbs) (without the stand)

Mass

AC power cord, Power cord holder × 1, Screw × 2 (for power cord holder),

Circular polarizing glasses × 2 (for 3D viewing, not under warranty)

Accessories

LCD panel

Type

24˝ wide, active matrix TFT

Width: 518.4 mm (20 1/2˝) Height: 324 mm (12 7/8˝) Diagonal: 611.3 mm (24 1/4˝)

Effective screen size

Number of pixels displayed

Number of colors displayed

Contrast ratio (TYP.)

1920 × 1200

16.77 million

1000:1

Input/output terminals

DVI-D (HDCP)

DVI-D signal input (compatible with HDCP): DVI-D connector x 1 (compatible with DDC2B)

E. AUDIO 3G SDI/HD SDI/SD SDI (IN 1/L)

E. AUDIO 3G SDI/HD SDI/SD SDI (IN 2/R)

Digital signal input (compatible with EMBEDDED AUDIO/DUAL LINK signals):

Auto detection, 2 line, BNC connector x 2

E. AUDIO 3G SDI/HD SDI/SD SDI

(ACTIVE OUT)

Digital signal output (compatible with EMBEDDED AUDIO signals):

2 line reclocked out, BNC connector x 2

AUDIO (IN)

Analog audio signal input: 1 line, RCA connector x 2,

500 mV (rms), high impedance

AUDIO (MONITOR OUT)

Analog audio signal input: 1 line, RCA connector x 2,

500 mV (rms)

REMOTE (MAKE/TRIGGER)

REMOTE (RS-485)

→ “Using the MAKE/TRIGGER system” on page 26

→ “Using the serial communication” on page 28

REMOTE (RS-232C)

Available signals

The following signals are available for this monitor.

√ : Acceptable

Video signals

— : Not acceptable

Input terminals

E. AUDIO SDI (IN 1, IN 2)^*1

Signal format shown

in the status display

No.

Signal name

480/60i

DVI-D (HDCP) (Digital

component/Digital RGB)

(→ page 11)

SD/HD (1.5G)

3G SDI

—

√

DUAL LINK

MIX

—

√

480/60i

√

—

√

480/59.94i

576/50i

480/60p

480/59.94p

576/50p

640*480/60p

640*480/59.94p

720/60p

480/59.94i

576/50i

480/60p

480/59.94p

576/50p

640*480/60p

640*480/59.94p

720/60p

√

—

√

10 720/59.94p

11 720/50p

720/59.94p

720/50p

√

12 720/30p

720/30p

√

—

√

13 720/29.97p

14 720/25p

15 720/24p

16 720/23.98p

17 1080/60i

720/29.97p

720/25p

720/24p

720/23.98p

1080/60i

√

18 1080/59.94i

19 1035/60i

20 1035/59.94i

21 1080/50i

1080/59.94i

1035/60i

1035/59.94i

1080/50i

√

—

√

—

√

—

√

—

√

22 1080/60p

23 1080/59.94p

24 1080/50p

25 1080/30p

26 1080/29.97p

27 1080/25p

28 1080/24p

29 1080/23.98p

30 1080/30psF

31 1080/29.97psF

32 1080/24psF

33 1080/23.98psF

34 1080/25psF

1080/60p

1080/59.94p

1080/50p

1080/30p

1080/29.97p

1080/25p

1080/24p

1080/23.98p

1080/30psf

1080/29.97psf

1080/24psf

1080/23.98psf

1080/25psf

—

√

√ *

√

√ *

√

√ *

√

√ *

√

√ *

√

√ *

√

√ *

√

—

√

√ *

Compatible with EMBEDDED AUDIO signals.

If there is no payload ID, the signal is regarded as 1080/60i, and “1080/60i” and the status appear.

If there is no payload ID, the signal is regarded as 1080/59.94i, and “1080/59.94i” and the status appear.

If there is no payload ID, the signal is regarded as 1080/50i, and “1080/50i” and the status appear.

Notice on transportation

This monitor is precision equipment and needs dedicated packing material for transportation.

Never use any packing material supplied from sources other than JVC or JVC-authorized dealers.

● For easy understanding, pictures and illustrations are emphasized, omitted or composed, and may be slightly different from actual

products.

● Design and specifications are subject to change without notice.

● All company names and product names mentioned herein are used for identification purposes only, and may be the trademarks or

registered trademarks of their respective companies.

Specifications (cont.)

Computer signals (preset)

DVI-D (HDCP) terminals

Resolution

Frequency

No. Signal name

Scan system

Horizontal

640

Vertical

480

Horizontal (kHz)

Vertical (Hz)

59.9

VGA60

31.5

37.9

48.4

47.8

55.9

64.0

65.2

75.0

74.0

45.0

67.5

37.5

56.25

Non-interlace

WVGA60

SVGA60

852

480

59.9

800

600

60.3

XGA60

1024

1280

1440

1280

1680

1600

1920

1280

1920

1280

1920

768

60.0

WXGA (1280)

WXGA+60

SXGA60

768

60.0

900

60.0

1024

1050

1200

720

60.0

WSXGA+60

UXGA60

60.0

10 WUXGA60

11 720/60p

12 1080/60p

13 720/50p

14 1080/50p

60.0

1080

720

60.0

50.0

1080

50.0

● Non-preset signals may not be displayed normally.

● When a preset signal comes in, the signal format is shown on the status display. For other signals, the resolution is shown.

Specification of the DVI-D (HDCP) terminal

Connect it to the DVI-D output terminal on a personal computer.

No.

Input signal

T.M.D.S Data 0–

T.M.D.S Data 2–

T.M.D.S Data 1–

T.M.D.S Data 2+

T.M.D.S Data 1+

T.M.D.S Data 1 shield

T.M.D.S Data 0+

T.M.D.S Data 0 shield

T.M.D.S Data 2 shield

DDC Clock

DDC Data

+5 V Power

GND

T.M.D.S Clock shield

T.M.D.S Clock+

T.M.D.S Clock–

Hot Plug Detect

Dimensions

Unit: mm (inch)

99 (4)

VESA mounting holes

(Size: 4-M4, depth: 10 mm)

51.9 (2 1/8)

1.3 (1/16)

100

564 (22 1/4)

51 (2 1/8)

300 (11 7/8)

243 (9 5/8)

0111SKH-MW-MT

Alphasonik PM12005E User Manual
Braun Blender MX 2050 BLACK User Manual
Bunn TCD 1 User Manual
Canon A580 User Manual
Canon LS 270G User Manual
Casio Calculator FX 570W User Manual
Clarion CAA 188 210 User Manual
Excalibur electronic 368E User Manual
Gitzo Explorer Basalt GT2930EX User Manual
JVC GR SX860 User Manual