For Customer Use:
KS-AX3104
Enter below the Model No. and Serial No. which
are located on the top or bottom of the cabinet.
Retain this information for future reference.
KS-AX3102
KS-AX3101D
Model No.
Serial No.
POWER AMPLIFIER: INSTRUCTIONS
УСИЛИТЕЛЬ МОЩНОСТИ: ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ
LVT2205-001A
[K/US]
1110NYMMDWTKK
EN, RU
© 2011 Victor Company of Japan, Limited
POWER SUPPLY
ENGLISH
Thank you for purchasing a JVC product.
If you have any questions or require information regarding installation kits, consult your “JVC IN-
CAR ENTERTAINMENT” or a company supplying the kits.
KS-AX3104
KS-AX3101D
KS-AX3102
* Not Supplied
For safety....
• Stop the car before performing any complicated operations.
CAUTIONS AND NOTES
Fuse*
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems.
JVC recommends consulting a qualified technician for installation.
• This unit uses BTL (Balanced Transformerless) amplifier circuitry, i.e., floating ground system,
so comply with the following:
To metallic body or chassis
(To an accessory terminal)
– Do not connect the “·” terminals of the speakers to each other.
– Do not connect the “·” terminals of the speakers to the metal body or chassis.
• Cover the unused leads with insulating tape to prevent them from short circuiting.
• When an extension lead is used, it should be as thick and short as possible; connect it firmly
with insulating tape.
• Be sure to leave an appropriate space between the antenna (aerial) and the wires of this unit.
• If the fuse blows, first make sure the wires aren’t touching to cause a short circuit then replace
the old fuse with one with the same rating.
Remote turn-on line
JVC car receiver, etc.
Ignition switch
Car battery
Caution
To prevent short circuits while making connections, keep the battery’s negative terminal
disconnected.
• Do not let pebbles, sand or metallic objects get inside the unit.
• To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off
periodically.
• Listening to the tape, radio, CD or digital audio player, etc. with the volume set at a high level
for a long period of time will exhaust the battery, while the engine is turned off or while the
engine is idling.
• When using a power cord (purchased separately), be sure to place the fuse near the battery as
shown.
• Connect the lead wire (power cord) through which power is supplied directly to the battery’s
“ª” terminal only after all the other connections have been made.
The proper lead wire connected to each POWER terminal is as follows.
• + B and GND: AWG 8 to AWG 4 (The cross section is about 8 mm2 to 21 mm2.)
• REM: AWG 18 to AWG 8 (The cross section is about 0.8 mm2 to 8 mm2.)
• This unit becomes very hot. Be careful not to touch the unit not only when using but after using.
DO NOT disassemble the unit since there are no user serviceable parts inside.
a When you use JVC car receiver with a remote lead, connect to the REM terminal on this unit.
b When you connect a unit without a remote lead, connect to the accessory circuit of the car
which is activated by the ignition switch. In this case, noise may occur when the car receiver
is turned on or off. To avoid this noise, do not turn on or off the car receiver itself. You can
turn on or off the car receiver along with the on/off operation of the ignition switch.
INSTALLATION
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car.
• Mount this unit on a firm surface, such as in the
Å Location of the unit
trunk or under the front seat.
TERMINAL CONNECTIONS
When making terminal connections, properly fix each terminal with the provided screw by turning
it as illustrated.
• Since heat is generated in the unit, do not
mount it near inflammable objects. In addition,
mount it in an area that will not prevent the unit
from dissipating the heat.
• Do not mount the unit in the places subject to
heat: near a radiator, in a glove compartment or
• Use ring terminals (not provided) for secure connection.
Notes
Onto the trunk floor
• Make sure the screw is fixed in place to prevent disconnections.
• Avoid over-tightening as it may cause the damage to the screw or its
head slot.
in insulated areas such as under a car mat that
Under the front seat
will prevent the unit from dissipating heat.
• When mounting the unit under the front seat,
make sure that adjusting the seat position will
not catch any wire of the unit.
ı Install the unit
Provided screw
13
φ 4 × 20 mm ( /16 in.)
SPEAKER SYSTEMS
Notes
• Be sure not to connect the “·” terminals of the speakers to a common point.
• If the same lead is used for both left/right or front/rear speaker wirings, this unit cannot be used.
Always use the independent leads for each speaker. In this case, redo the wirings.
• Use the speakers with an impedance of 2 Ω to 8 Ω (4 Ω to 8 Ω: when used in Bridge Mode).
• Use the speakers which have sufficient capacity to the unit.
• When mounting this unit, be sure to use the
provided screws.
• If any other screws are used, there is a risk of
loosening the unit or damaging the parts under
the car floor.
• Before drilling holes in the trunk to install the
unit, make sure that there is a sufficient space
under the trunk so that you do not drill holes in
the fuel tank, etc.
The proper lead connected to each SPEAKER OUTPUT terminal is as follows.
KS-AX3104/KS-AX3102: AWG 18 to AWG 12 (The cross section is about 0.8 mm2 to 3.3 mm2).
KS-AX3101D: AWG 18 to AWG 8 (The cross section is about 0.8 mm2 to 8 mm2).
Drilled hole
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards but, like any electrical
equipment, care must be taken if you are to obtain the best results and safety is to be assured.
Dear Customer,
This apparatus is in conformance with the valid European directives and
standards regarding electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan, Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and interconnections between
pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and
withdraw the mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
61145 Friedberg
Germany
Information for Users on Disposal of Old Equipment and Batteries
[European Union only]
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any
way–switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for
unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your
family know how to do this. Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic
safety. It is illegal to watch television whilst driving.
These symbols indicate that the product and the battery with this symbol should
not be disposed as general household waste at its end-of-life.
If you wish to dispose of this product and the battery, please do so in accordance
with applicable national legislation or other rules in your country and municipality.
Products
By disposing of this product correctly, you will help to conserve natural resources
and will help prevent potential negative effects on the environment and human
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating will cause
damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws–to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
health.
Notice:
The sign Pb below the symbol for batteries indicates that this battery contains lead.
Battery
ABOVE ALL
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case — this could
result in a fatal electrical shock.
— NEVER guess or take chances with electrical equipment of any kind–it is better to be safe than sorry!
E43486-340B
1
CONTROLS
KS-AX3101D
2-Subwoofer system (2 amplifiers)
• Use the speakers with an impedance of 2 Ω to 8 Ω.
• Incoming signals from INPUT jacks are emitted through the PRE OUT jacks.
KS-AX3104
Å
INPUT
L/MONO
JVC car receiver, etc.
CROSSOVER
HIGH INPUT
HIGH INPUT
CROSSOVER
L/MONO
OFF
OFF
LEVEL
LEVEL
LPF
KS-AX3102
LEVEL
HPF
LPF
HPF
POWER
ı Speaker input connector.
MIN
MAX
MIN
MAX
Connector lead
To Receiver
Line out (Rear)
or
Subwoofer out
FRONT
REAR
=
=
=
a White "LEFT (+)"
b Black "RECEIVER GND"
c Gray "RIGHT (+)"
Left (+) lead
Chassis*1
KS-AX3101D
2
*
Right (+) lead
PRE OUT INPUT
HIGH INPUT
L
L/MONO
CROSSOVER
OFF
Subwoofer
LEVEL BASS BOOST
LPF
R
LPF
HPF
R
POWER
POWER
MIN
MAX
MIN
MAX
MIN
MAX
50Hz
200Hz
PRE OUT INPUT
HIGH INPUT
L
L/MONO
2
*
Å POWER indicator
R
R
The green lamp lights while the unit is turned on.
ı CROSSOVER filter switch
OFF: Normally set to this position. The switch is preset to this position when the unit is
shipped.
Subwoofer
2-Subwoofer system
• Use the speakers with an impedance of 4 Ω to 8 Ω.
LPF: Set to this position when you want to turn on the LPF (Low-Pass Filter) switch. The Low-
Pass Filter transmits frequencies lower than 80 Hz.
HPF: Set to this position when you want to turn on the HPF (High-Pass Filter) switch. The
High-Pass Filter transmits frequencies higher than 150 Hz.
Å
JVC car receiver, etc.
Ç Input LEVEL controller
ı Speaker input connector.
The input level can be adjusted with this control when this unit is connected to other source
equipment. Adjust the level while listening to the sound. This control is preset to MIN when
the unit is shipped.
Line out (Rear)
or
Connector lead
To Receiver
=
=
=
a White "LEFT (+)"
b Black "RECEIVER GND"
c Gray "RIGHT (+)"
Left (+) lead
Subwoofer out
Î BASS BOOST controller
Chassis*1
2
*
Turning this boosts the 45 Hz frequency within the range of 0 dB to +18 dB. Adjust the level
while listening to the sound. This controller is preset to MIN when the unit is shipped.
Right (+) lead
PRE OUT INPUT
HIGH INPUT
‰ LPF (Low-Pass Filter) controller
L
L/MONO
Adjust the cutoff frequency (the Low-Pass Filter transmits frequencies lower than the cutoff
frequency) within the range of 50 Hz to 200 Hz. Adjust the level while listening to the
sound. This controller is preset to 50 Hz when the unit is shipped.
R
R
Subwoofer
Subwoofer
5-speaker system plus subwoofer—5.1-channel (3 amplifiers)
• Use the speakers with an impedance of 2 Ω to 8 Ω.
• Be sure to connect the line output from the receiver to the left (L) jack on this unit.
TROUBLESHOOTING
The POWER indicator does not light.
• Change the fuses if the current one is blown.
• Connect the ground lead securely to a metal part of the car.
• Turn on the equipment connected to this unit.
• Confirm the battery voltage (11 V to 16 V).
• Use a relay if your system employs too many amplifiers.
• Leave the unit turned off to cool it down if it heats up abnormally.
Line out (Front)
2
*
Å
JVC amplifier, etc.
(Purchased separately)
JVC car receiver, etc.
Subwoofer out
2
*
Line out (Rear)
Line out
(Center)
Front
Speaker
Rear
Speaker
No sound is heard.
ı Speaker input connector.
• Confirm the connections for the power supply (see "POWER SUPPLY" on page 1).
• Connect the RCA pin cords to the INPUT jacks, or the speaker input connector to the HIGH
INPUT terminal.
• Confirm the speaker wirings and the position of the CROSSOVER filter switch (See “SPEAKER
CONNECTIONS” on page 2).
2
2
Connector lead
To Receiver
*
*
=
=
=
a White "LEFT (+)"
b Black "RECEIVER GND"
c Gray "RIGHT (+)"
Left (+) lead
Chassis*1
PRE OUT INPUT
HIGH INPUT
L
L/MONO
Left (+) lead
R
R
Alternator noise is heard.
• Keep the leads of the POWER terminals away from the RCA pin cords.
• Keep the RCA pin cords away from other electrical cables in the car.
• Connect the ground lead securely to a metal part of the car.
• Make sure the speaker negative leads do not touch the car chassis.
• Connect a bypass capacitor across the accessory switches (horn, fan, etc....).
JVC amplifier, etc.
(Purchased separately)
Center Speaker
Subwoofer
Noise is made when you connect the unit to an AM (MW/LW) tuner.
• Move all the leads of this unit away from the antenna (aerial) lead.
SPECIFICATIONS
KS-AX3104
KS-AX3102
KS-AX3101D
Power Output
• Normal Mode:
60 W RMS × 4 channels at 4 Ω and ≤ 1% THD + N
65 W RMS × 2 channels at 4 Ω and ≤ 1% THD + N
250 W RMS × 1 channels at 4 Ω and ≤ 1% THD + N
76 dBA (reference: 1 W into 4 Ω)
76 dBA (reference: 1 W into 4 Ω)
60 dBA (reference: 1 W into 4 Ω)
Signal-to-Noise Ratio
Power Output
• Normal Mode:
90 W RMS × 4 channels at 2 Ω and ≤ 1% THD + N
150 W RMS × 2 channels at 4 Ω and ≤ 1% THD + N
800 W (400 W × 2)
90 W RMS × 2 channels at 2 Ω and ≤ 1% THD + N
150 W RMS × 1 channels at 4 Ω and ≤ 1% THD + N
400 W
400 W RMS × 1 channels at 2 Ω and ≤ 1% THD + N
• Bridge Mode:
—
Maximum Power Output
Load Impedance
800 W
• Normal Mode:
4 Ω (2 Ω to 8 Ω allowance)
4 Ω (4 Ω to 8 Ω allowance)
5 Hz to 50,000 Hz ( +0 dB, –3 dB)
2 V/21 kΩ (0.3 V to 6 V, variable)
Less than 0.04% (at 1 kHz)
DC 14.4 V (11 V to 16 V allowance)
Negative ground
4 Ω (2 Ω to 8 Ω allowance)
4 Ω (4 Ω to 8 Ω allowance)
5 Hz to 50,000 Hz ( +0 dB, –3 dB)
2 V/21 kΩ (0.3 V to 6 V, variable)
Less than 0.04% (at 1 kHz)
DC 14.4 V (11 V to 16 V allowance)
Negative ground
4 Ω (2 Ω to 8 Ω allowance)
—
• Bridge Mode:
Frequency Response
Input Sensitivity/Impedance
Distortion
20 Hz to 200 Hz ( +0 dB, –3 dB)
2 V/40 kΩ (0.3 V to 6 V, variable)
Less than 0.08% (at 100 Hz)
DC 14.4 V (11 V to 16 V allowance)
Negative ground
Power Requirement
Grounding system
Dimensions (W×H×D)
335 mm × 51 mm × 212 mm
202 mm × 51 mm × 212 mm
222 mm × 51 mm × 212 mm
4
1
6
1
6
12
1
6
(13- /16 in. × 2- /16 in. × 8- /16 in.)
(8 in. × 2- /16 in. × 8- /16 in.)
(8- /16 in. × 2- /16 in. × 8- /16 in.)
Mass (approx.)
Accessories
2.43 kg (5.3 lbs)
1.52 kg (3.4 lbs)
1.83 kg (4.0 lbs)
Speaker input connector 3P × 2
Speaker input connector 3P × 1
Speaker input connector 3P × 1
Mounting Screw φ 4 × 20 mm (13/16 in.) × 4
Mounting Screw φ 4 × 20 mm (13/16 in.) × 4
Mounting Screw φ 4 × 20 mm (13/16 in.) × 4
Design and specifications are subject to change without notice.
3
|