ENGLISH
CONTENTS
SAFETY PRECAUTIONS
QUICK OPERATION GUIDE
MAJOR FEATURES
2 – 5
6 – 7
8
PROVIDED ACCESSORIES
GETTING STARTED
9
10 – 17
BASIC VIDEO RECORDING 18 – 19
COMPACT
VHS CAMCORDER
BASIC DIGITAL STILL CAMERA (D.S.C.)
SHOOTING
20 – 22
RECORDING
23 – 38
Basic Features ................................. 23
Advanced Features ........................... 28
GR-SXM920
VIDEO PLAYBACK
39 – 41
Basic Playback ................................ 39
Features ........................................ 40
Using The Cassette Adapter ................ 41
BASIC CONNECTIONS
Basic Connections And Tape Dubbing ...... 42
D.S.C. PLAYBACK 44 – 51
42 – 43
Basic Playback ................................ 44
Connection ..................................... 45
Advanced Features ........................... 46
USING THE REMOTE
CONTROL UNIT
52 – 56
Playback Zoom ................................ 53
Insert Editing (VIDEO) ....................... 54
Insert Editing (Inserting A Still Image From
The Built-in Memory Onto A Tape) ...... 55
Audio Dubbing ................................. 55
Animation And Time-Lapse .................. 56
TROUBLESHOOTING
INDEX
57 – 59
60 – 63
Controls, Connectors And Indicators ....... 60
Indications ..................................... 62
USER MAINTENANCE
CAUTIONS
64
65 – 67
68 – 69
70
TERMS
INSTRUCTIONS
For Customer Use:
SPECIFICATIONS
ESPAÑOL
71 – 73
Enter below the Model No. and Serial No. which is located on the
bottom of cabinet. Retain this information for future reference.
FOR SERVICING (Only in U.S.A.) 74
WARRANTY (Only in U.S.A.)
75
Model No.
Serial No.
LYT0467-001A
EN
EN3
This camcorder is designed to be used with NTSC-type color television signals. It cannot be used for
playback with a television of a different standard. However, live recording and LCD monitor/viewfinder
playback are possible anywhere. Use the BN-V11U/V12U/V20U battery packs and, to recharge them, the
provided multi-voltage AC Power Adapter/Charger. (An appropriate conversion adapter may be necessary
to accommodate different designs of AC outlets in different countries.)
ATTENTION:
The product that you have purchased is powered by a rechargeable battery. The battery is recyclable. At
the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into
the municipal waste stream. Check with your local solid waste officials for details in your area for
recycling options or proper disposal.
The EPA certified RBRC® Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery indicates JVC is
voluntarily participating in an industry program to collect and recycle these batteries at the end of their
useful life, when taken out of service in the United States. The RBRC® program provides a convenient
alternative to placing used Ni-Cd batteries into the trash or the municipal waste stream, which may be
illegal in your area. Please call 1-800-8-BATTERY™ for information on Ni-Cd battery recycling and
disposal bans/restrictions in your area. JVC’s involvement in this program is part of our commitment to
preserving our environment and conserving our natural resources.
When the equipment is installed in a cabinet or on a shelf, make sure that is has sufficient space on all
sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)
No naked flame sources, such as lighted candles, should be placed on the apparatus.
When discarding batteries, environmental problems must be considered and the local rules or laws
governing the disposal of these batteries must be followed strictly.
The apparatus shall not be exposed to dripping or splashing.
Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
4
EN
5. Ventilation
IMPORTANT PRODUCT
SAFETY INSTRUCTIONS
Slots and openings in the cabinet are provided for
ventilation. To ensure reliable operation of the product
and to protect it from overheating, these openings must
not be blocked or covered.
•Do not block the openings by placing the product on a
bed, sofa, rug or other similar surface.
•Do not place the product in a built-in installation such
as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been
adhered to.
Electrical energy can perform many useful functions.
But improper use can result in potential electrical
shock or fire hazards. This product has been
engineered and manufactured to assure your
personal safety. In order not to defeat the built-in
safeguards, observe the following basic rules for its
installation, use and servicing.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only
as recommended by the manufacturer.
ATTENTION:
Follow and obey all warnings and instructions
marked on your product and its operating instruc-
tions. For your safety, please read all the safety and
operating instructions before you operate this
product and keep this manual for future reference.
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements
for the grounding electrode.
INSTALLATION
1. Grounding or Polarization
(A) Your product may be equipped with a polarized
alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature.
If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of
the polarized plug.
(B) Your product may be equipped with a 3-wire
grounding-type plug, a plug having a third (ground-
ing) pin. This plug will only fit into a grounding-type
power outlet. This is a safety feature.
2. Lightning
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will
prevent damage to the product due to lightning and
power-line surges.
If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding-type plug.
3. Power Lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching
such power lines or circuits as contact with them might
be fatal.
2. Power Sources
Operate your product only from the type of power
source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult
your product dealer or local power company. If your
product is intended to operate from battery power, or
other sources, refer to the operating instructions.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
3. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire
or electric shock.
ANTENNA
LEAD IN WIRE
GROUND CLAMP
4. Power Cord Protection
Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the product.
ANTENNA
DISCHARGE UNIT
(NEC SECTION
ELECTRIC SERVICE
EQUIPMENT
810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
EN5
USE
SERVICING
1. Accessories
1. Servicing
To avoid personal injury:
If your product is not operating correctly or exhibits a
marked change in performance and you are unable
to restore normal operation by following the detailed
procedure in its operating instructions, do not
attempt to service it yourself as opening or removing
covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
•Do not place this product on an unstable cart,
stand, tripod, bracket or table. It may fall, causing
serious injury to a child or adult, and serious
damage to the product.
•Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the
product.
•Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s
instructions for any mounting of the product.
•Do not try to roll a cart with small casters across
thresholds or deep-pile carpets.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
2. Product and Cart
PORTABLE CART WARNING
(Symbol provided by RETAC)
Combination
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or damaged in
any way.
A product and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may cause
the product and cart
combination to overturn.
3. Water and Moisture
Do not use this product near water—for example,
near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool and
the like.
f. When the product exhibits a distinct change in
performance—this indicates a need for service.
3. Replacement Parts
4. Object and Liquid Entry
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other
hazards.
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any kind
on the product.
5. Attachments
4. Safety Check
Do not use attachments not recommended by the
manufacturer of this product as they may cause
hazards.
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in safe
operating condition.
6. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
7. Heat
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
QUICK OPERATION GUIDE (VIDEO)
6
EN
The image you shoot is recorded onto a video tape.
SUPPLY POWER
INSERTING A VIDEO
CASSETTE
A Hook on.
B Push in.
PUSH Button
EJECT Switch
BATTERY RELEASE
Using the battery pack
1 Open the LCD monitor fully.
Hook its end to the camcorder
and push the
2 Slide EJECT to open the cassette holder.
3 Insert a video cassette.
battery pack in until it locks in place
(Charging procedure, ੬ pg. 10)
.
4 Press PUSH to close the cassette holder.
(For more details, ੬ pg. 12)
To remove the battery pack
Slide BATTERY RELEASE and pull out the battery
pack.
PLAYBACK
SHOOTING
Rewind (2) Button
3
1
LENS COVER
Open/Close Ring
3
Set to “AUTO”
or “PRO.”.
Play/Pause (4/6)
4
Button
Set to
2
“PLAY”.
Recording Start/Stop Button
4
Stop (5) Button
Set to “VIDEO”.
1
Set to “VIDEO”.
2
1 Set the System Select Switch to “VIDEO”.
2 Set the Power Switch to “PLAY”.
1 Turn the LENS COVER Open/Close Ring to
open the lens cover.
2 Set the System Select Switch to “VIDEO”.
3 Set the Power Switch to “AUTO” or “PRO.”.
— The power lamp will light and an image
will appear.
3 Press
2.
— The tape will automatically stop at the
beginning of the tape.
4 Press 4/6.
— Playback starts and the playback picture
appears.
•To stop playback, press 5.
(For more details, ੬ pg. 39.)
•The viewfinder switches off automatically to
save power when the LCD monitor is opened
at an angle of over 60 degrees.
•The LCD monitor turns on/off when it is
opened/closed at approx. 60 degrees.
4 Press the Recording Start/Stop Button.
— Recording starts.
•To stop recording temporarily, momentarily
press the Recording Start/Stop Button once
again.
(For more details, ੬ pgs. 18, 19)
•The viewfinder switches off automatically to
save power when the LCD monitor is opened
at an angle of over 60 degrees.
•The LCD monitor turns on/off when it is
opened/closed at approx. 60 degrees.
Or simply play back the tape on a VHS VCR
using the Cassette Adapter (VHS Playpak).
੬ pg. 41
QUICK OPERATION GUIDE (D.S.C.)
A still image you shoot is stored in the camcorder's built-in memory.
EN7
SHOOTING
SUPPLY POWER
A Hook on.
SNAPSHOT Button
4
B
Push in.
1
LENS COVER
Open/Close Ring
3
Set to “AUTO”
or “PRO.”.
BATTERY RELEASE
Set to “D.S.C.”.
2
Using the battery pack
Hook its end to the camcorder
battery pack in until it locks in place
(Charging procedure, ੬ pg. 10)
To remove the battery pack
Slide BATTERY RELEASE and pull out the battery
and push the
.
1 Turn the LENS COVER Open/Close Ring to
open the lens cover.
2 Set the System Select Switch to “D.S.C.”.
3 Set the Power Switch to “AUTO” or “PRO.”.
— The power lamp will light and an image
will appear.
pack.
4 Press the SNAPSHOT Button.
— A still image is shot and is stored in the
camcorder’s memory.
PLAYBACK
(For more details, ੬ pgs. 20 – 22)
•The viewfinder switches off automatically to
save power when the LCD monitor is opened
at an angle of over 60 degrees.
3 (Next/Previous Page
2/PAGE – or 3/PAGE +) Buttons
•The LCD monitor turns on/off when it is
opened/closed at approx. 60 degrees.
2
Set to “PLAY”.
1
Set to “D.S.C.”.
1 Set the System Select Switch to “D.S.C.”.
2 Set the Power Switch to “PLAY”.
— A still image stored in memory appears.
3 Press 2/PAGE – or 3/PAGE + to select the
still image you want to view.
(For more details, ੬ pg. 44.)
•The viewfinder switches off automatically to
save power when the LCD monitor is opened
at an angle of over 60 degrees.
•The LCD monitor turns on/off when it is
opened/closed at approx. 60 degrees.
MAJOR FEATURES
8
EN
Integrated Auto Light
(੬ pg. 27)
Picture Stabilizer (੬ pg. 25)
Program AE with Special
Effects (੬ pg. 29)
Ⅲ Electronic Fog Filter
Ⅲ ND Effect
Digital Hyper Zoom
Ⅲ Sepia
Ⅲ Twilight
Ⅲ Sports
(੬ pg. 25)
Zoom in
Ⅲ Nega/Posi
Ⅲ 1/2000 sec. High Speed Shutter
Zoom out
Super VHS-ET (੬ pg. 15)
TBC (Time Base Corrector)
(੬ pg. 40)
Digital Still Camera Built-in
(PC communication capable)
(੬ pg. 20 – 22, 44 – 51)
NOTES about Automatic Demonstration
Automatic Demonstration takes place when ”DEMO MODE” is set to ”ON”
(factory-preset).
Ⅲ Available when the System Select Switch is set to “VIDEO” and the
DEMO MODE
Power Switch is set to ”AUTO” or ”PRO.”.
OFF
ON
Ⅲ Operating the Power Zoom Lever during the demonstration stops the
demonstration temporarily. If the Power Zoom Lever is not moved for
more than 1 minute after that, the demonstration will resume.
Ⅲ To cancel Automatic Demonstration, set the Power Switch to “PRO.”
and press MENU while the demo is in progress. This takes you directly
to the demo mode’s Setting Menu (so you will not have to go through
EX I T
the main Menu Screen.) Rotate the Select Wheel to select “OFF” and
Setting Menu
press it. The Menu Screen appears with the highlight bar on “RETURN”.
Press it to close the Menu Screen.
* ”DEMO MODE” remains ”ON” even if the camcorder power is turned off.
NOTE:
When a tape whose Erase Protection tab is in the position that allows recording is loaded in the
camcorder, demonstration is not available.
Cassettes marked
and
can be used with this camcorder.
PROVIDED ACCESSORIES
EN9
• AC Power
Adapter/Charger
AA-V16U
• Cassette Adapter
(VHS Playpak) C-P7U
• Battery Pack
BN-V11U
(for Windows® PC)
• Remote Control
Unit RM-V715U
• PC Connection Cable
• DC Cord
• Shoulder Strap
• Lithium Battery CR2025
(for clock operation)
• CD-ROM including
two software
programs
Optional Accessories
• Battery Packs BN-V12U, BN-V20U, BN-V856U
• Car Battery Charger BH-V3U
• Battery Charger BH-VC10U
• Audio/Video Cable
• S-Video Cable QAM0004-004
• Car Battery Cord AP-V7U
Some accessories are not
available in some areas. Please
consult your nearest JVC dealer
for details on accessories and their
availability.
• Compact S-VHS (
• Compact VHS (
) Cassettes ST-C-40/30/20
) Cassettes TC-40/30/20
• Active Carrying Bag CB-V7U
GETTING STARTED
10
EN
Battery pack BN-V12U or BN-V20U
Marks
Power
This camcorder’s 3-way power supply system lets you
choose the most appropriate source of power. Do not use
provided power supply units with other equipment.
To AC outlet
CHARGE
indicator
CHARGING THE BATTERY PACK
Make sure you unplug the camcorder’s DC cord from
the AC Power Adapter/Charger. Plug the AC Adapter/
Charger’s power cord into an AC outlet.
1
2
AC Power
Adapter/Charger
AA-V16U
Align the marks and slide the battery pack in the
direction of the arrow until it locks in place. The
CHARGE indicator begins blinking to indicate
charging has started.
DC OUT connector
Battery pack Charging time
When the CHARGE indicator stops blinking but stays
lit, charging is finished. Slide the battery in the
opposite direction of the arrow and lift off. Remember
to unplug the AC Adapter/Charger’s power cord from
the AC outlet.
3
BN-V11U
approx. 1 hr. 10 min.
approx. 1 hr. 10 min.
approx. 1 hr. 50 min.
BN-V12U (optional)
BN-V20U (optional)
Charge Marker
A charge marker is provided on the battery pack to help
you remember whether it has been charged or not. Two
colors are provided (red and black)—you choose which
one means charged and which means discharged.
Charge marker
NOTES:
● Perform charging where the temperature is between 10°
and 35°C (50°F and 95°F). 20° to 25°C (68°F to 77°F) is
the ideal temperature range for charging. If the environ-
ment is too cold, charging may be incomplete.
● Charging times noted above are for a fully discharged
battery pack.
● Charging time varies according to the ambient
temperature and the status of the battery pack.
● To avoid interference with reception, do not use the AC
Power Adapter/Charger near a radio.
● If you connect the camcorder’s DC cord to the adapter
during battery charging, power is supplied to the
camcorder and charging stops.
ATTENTION:
Charging a battery with some charge
remaining reduces that battery’s capacity.
Perform the procedure below to fully
discharge the battery pack before
recharging.
● Since the AC Power Adapter/Charger processes
electricity internally, it becomes warm during use. Be
sure to use it only in well-ventilated areas.
● When charging the battery pack for the first time or after
a long storage period, the CHARGE indicator may not
light. In this case, remove the battery pack from the AC
Power Adapter/Charger, then try charging again.
● If the battery operation time remains extremely short
even after having been fully charged, the battery is worn
out and needs to be replaced. Please purchase a new
one.
1. Attach the battery pack to the camcorder
and make sure a cassette is not inserted,
then set the Power Switch to ”AUTO” or
”PRO.”.
2. The camcorder power turns off
automatically when discharging is
complete.
When you are not using a battery pack for
a long period of time, be sure to fully
discharge it before storing because leaving
a battery with some charge left over also
reduces performance.
● Remember to set the charge marker after charging a
battery pack or after detaching a discharged one from
your camcorder.
EN11
USING THE BATTERY PACK
Hook on.
A
Hook its end to the camcorder
pack in until it locks in place
and push the battery
.
B
Push in.
•
If the battery pack is attached in the wrong position, a
malfunction may occur.
To Detach The Battery Pack . . .
.... slide BATTERY RELEASE and pull out the battery pack.
Approximate recording time
LCD
LCD
LCD
Battery pack monitor off/
monitor on/
monitor on/
Viewfinder on Viewfinder off Viewfinder on
BN-V11U
1 hr. 20 min.
(45 min.)
1 hr. 10 min.
(40 min.)
1 hr. 5 min.
(40 min.)
BATTERY RELEASE Switch
BN-V12U
(optional)
1 hr. 20 min.
(45 min.)
1 hr. 10 min.
(40 min.)
1 hr. 5 min.
(40 min.)
ATTENTION:
Before detaching the power source,
make sure that the camcorder’s power
is turned off. Failure to do so can result
in a camcorder malfunction.
BN-V20U
(optional)
2 hrs. 10 min.
(1 hr. 15 min.) (1 hr. 10 min.)
1 hr. 55 min.
1 hr. 45 min.
(1 hr. 5 min.)
BN-V856U 8 hrs. 30 min. 7 hrs. 40 min.
(optional)
7 hrs.
(5 hrs. 10 min.) (4 hrs. 50 min.) (4 hrs. 30 min.)
(
) : when the video light is on.
INFORMATION:
NOTES:
VU-V856KIT is a set composed of the BN-
V856U battery pack and AA-V80U AC Power
Adapter/Charger.
● Recording time is reduced significantly under the
following conditions:
•Zoom or Record-Standby mode is engaged repeatedly.
•The LCD monitor is used repeatedly.
● Before extended use, it is recommended that you
prepare enough battery packs to cover 3 times the
planned shooting time.
Read the VU-V856KIT’s instruction manuals
before using.
It is impossible to charge the BN-V856U battery
pack using the provided AC Power Adapter/
Charger. Use the optional AA-V80U AC Power
Adapter/Charger.
To DC IN
connector
USING AC POWER
To AC outlet
To DC OUT
connector
Use the AC Power Adapter/Charger (connect as shown in
the illustration).
NOTES:
Core
●The provided AC Power Adapter/Charger features
automatic voltage selection in the AC range from 110 V
to 240 V.
filter
AC Power
Adapter/
Charger
DC Cord
●For other notes, ੬ pg. 10.
AA-V16U
USING A CAR BATTERY
Use the optional Car Battery Cord or Car Battery Charger/
Adapter (connect as shown in the illustration).
To car’s
cigarette
lighter
NOTES:
socket
Car Battery Cord
AP-V7U (optional)
●When using the car battery, leave the engine idling.
●The optional Car Battery Charger (BH-V3U) can also be
used to charge the battery pack (except BN-V20U/
V856U).
●When using the optional Car Battery Charger or Car
Battery Cord (AP-V7U), refer to the respective instruction
booklet.
Car Battery
Charger/Adapter
BH-V3U (optional)
GETTING STARTED (cont.)
12
EN
Slot
Clock (Lithium) Battery Insertion/Removal
This battery is necessary for clock operation and to
perform date/time settings.
Switch off the unit’s power and remove the power
supply unit (battery pack, AC Power Adapter/Battery
Charger, etc.).
1
Pull out the battery holder to remove it from the
camcorder.
2
3
4
Insert the battery in the holder, and be sure to have
the “+” mark visible.
Battery holder
Slide the holder back into the slot until you hear a
click.
NOTES:
● See “SAFETY PRECAUTIONS” (੬ pg. 2) for information
on safe handling of lithium batteries.
● To avoid losing the battery and/or battery holder, place
the camcorder with the grip side up as shown in the
illustration when inserting/removing the battery.
Loading/Unloading A Cassette
Cassette holder
Open the LCD monitor fully.
1
Slide EJECT until the cassette holder opens. Do not
use force to open.
2
3
4
Insert or remove a cassette. When inserting, make
sure the label is facing outward.
Press PUSH to close the cassette holder until it locks
into place. Close the LCD monitor.
PUSH Button
EJECT Switch
NOTES:
● Closing the LCD monitor while the cassette holder is still
open may cause damage to the LCD monitor.
● The cassette holder can’t be opened unless a power
supply is attached.
● Make sure that the tape is not slack when loading the
cassette. If there is any slack, turn the gear on the
cassette in the direction of the arrow to take up the
slack.
Turn to take
up slack.
● Make sure the Erase Protection tab is in the position that
allows recording. If not, slide the tab. Some cassettes
have removable tabs. If the tab has been removed, cover
the hole with adhesive tape.
Erase Protection tab
Gear
● The cassette holder cannot be opened while the
camcorder is in the record mode.
EN13
Date/Time Settings
Set the System Select Switch to “VIDEO” or “D.S.C.”,
and set the Power Switch to “PRO.”. The power lamp
comes on.
1
System
Select Switch
Press MENU. The Menu Screen appears.
2
3
Rotate the Select Wheel to move the highlight bar to
“NEXT” in Menu Screen 1 and press it to display
Menu Screen 2. Then, rotate it to move the highlight
bar to “DATE/TIME” and press it. The DATE/TIME
Menu appears.
Select Wheel
Power Switch
MENU Button
•To return to the previous settings, rotate the Select
Wheel to move the highlight bar to “EXIT” and
press it, then go to step 7.
•To set only the time without changing the date, go
to step 5.
Display
Menu Screen 1
Menu Screen 2
4
NEXT
To set “YEAR”, “MONTH” or “DAY”, rotate the Select
Wheel to move the highlight bar to the desired item,
and press it. When the setting begins blinking, rotate
the Select Wheel until the correct setting appears and
then press it. The setting stops blinking.
D. ZOOM
TELE MACRO
ON
OFF
ON
4
5
4
BACK
REC T I ME
OFF
OFF
ENGL I SH
Repeat for other date settings.
I NT. T I ME
T I TLE LANG.
DATE / T I ME
JL I P I D NO.
DEMO MODE
Rotate the Select Wheel to move the highlight bar to
“TIME” and then press it. When the hour setting
begins blinking, rotate the Select Wheel until the
correct setting appears and then press it. When the
hour setting stops blinking and the minute setting
begins blinking, rotate the Select Wheel until the
correct setting appears and then press it. The minute
setting stops blinking.
0 6
OFF
4
RETURN
DATE / T I ME
DATE/TIME Menu
YEAR
MONTH
DAY
2 0 0 0
JUN
2 8
:
T I ME
PM
8
2 0
12-hour indication
with AM or PM
When none of these settings (“YEAR”, “MONTH”,
“DAY”, “TIME”) blinks, rotate the Select Wheel to
move the highlight bar to “EXIT”, and press it. The
Menu Screen reappears with the highlight bar on
“RETURN”.
6
7
EX I T
4
BACK
REC T I ME
OFF
OFF
ENGL I SH
Press the Select Wheel to close the Menu Screen.
I NT. T I ME
T I TLE LANG.
DATE / T I ME
JL I P I D NO.
DEMO MODE
0 6
OFF
NOTE:
To display the date and time in the camcorder’s display
and on a connected TV, see “Date/Time Insert”
(੬ pg. 33).
4
RETURN
GETTING STARTED (cont.)
14
EN
Recording Mode Setting
Set depending on your preference.
Set the System Select Switch to “VIDEO”, then set the
System
Select Switch
1
Power Switch to “AUTO” or “PRO.”. Press SP/EP for
more than 1 second. “SP” (Standard Play) provides
higher picture and sound quality and is better for
dubbing, while “EP” (Extended Play) is more
economical, providing three times the recording time.
Select Wheel
NOTE:
If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.
Power Switch
SP/EP Recording
Mode Button
MENU Button
Tape Length Setting
Viewfinder
Display
Set the tape length according to the length of the tape
used.
T3 0
Tape length indicator
SP
Recording mode
indicator
Set the Power Switch to “PRO.”, then press MENU.
1
TELE MACRO
OFF
Rotate the Select Wheel to move the highlight bar to
TAPE LENGTH
P I CTURE
T3 0
2
“TAPE LENGTH”, then press it. The TAPE LENGTH
Setting Menu appears.
Menu Screen
STANDARD
FULL
SNAPSHOT
Rotate the Select Wheel to move the highlight bar to
the correct tape length setting. T20=20 minutes of
recording time, T30=30 minutes, T35=35 minutes,
and T40=40 minutes (in SP).
•To return to the previous setting, rotate the Select
Wheel to move the highlight bar to “EXIT”.
4
RETURN
3
TAPE LENGTH
TAPE LENGTH
Setting Menu
T2 0
T3 0
T3 5
T4 0
Press the Select Wheel. The Menu Screen reappears
with the highlight bar on “RETURN”. Press the Select
Wheel again to close the Menu Screen.
4
EX I T
TELE MACRO
OFF
NOTE:
TAPE LENGTH
P I CTURE
SNAPSHOT
T4 0
STANDARD
FULL
The tape remaining time (੬ pg. 18) displayed in the
viewfinder is correct only if the correct tape length has
been selected.
4
RETURN
EN15
Recording Format Setting
Set the recording format according to the format of the
tape used or type of recording you wish to perform.
Set the Power Switch to “PRO.”. Press MENU.
1
If a VHS cassette is loaded . . .
2
.... rotate the Select Wheel to move the highlight bar
to “S-VHS ET”, then press it. The S-VHS ET
Setting Menu appears.
Select Wheel
Power Switch
MENU Button
If an S-VHS cassette is loaded . . .
.... rotate the Select Wheel to move the highlight bar
to “S-VHS”, then press it. The S-VHS Setting
Menu appears.
Rotate the Select Wheel to set to either of the
parameters, then press it. The highlight bar moves to
“EXIT”.
Display: when a VHS cassette is loaded.
3
Menu Screen
4
NEXT
In the S-VHS ET Setting Menu,
D. ZOOM
ON
TELE MACRO
OFF
ON : Records with S-VHS picture quality on a VHS
cassette (factory-preset). This is called Super
VHS ET (Expansion Technology).
–
S
VHS ET
OFF
T3 0
STANDARD
FULL
TAPE LENGTH
P I CTURE
SNAPSHOT
When an S-VHS
cassette is loaded:
S-VHS
OFF: Records in VHS.
4
RETURN
In the S-VHS Setting Menu,
ON : Records in S-VHS on an S-VHS cassette
(factory-preset).
–
S
VHS ET
Setting Menu
OFF: Records in VHS on an S-VHS cassette.
ON
OFF
Press the Select Wheel. The Menu Screen reappears
with the highlight bar on “RETURN”. Press the Select
Wheel again to close the Menu Screen.
•When the S-VHS ET mode is engaged, “S-ET” is
displayed.
•During S-VHS record mode, “S“ is displayed.
•When S-VHS ET or S-VHS recording starts, “S-VHS
REC.” is displayed for approx. 3 seconds.
4
EX I T
TELE MACRO
OFF
TAPE LENGTH
P I CTURE
SNAPSHOT
T3 0
STANDARD
FULL
Menu Screen
NOTE:
4
RETURN
If a cassette is not loaded, “S-VHS” will be displayed in the
Menu Screen.
Normal Screen
CONTINUED ON NEXT PAGE
GETTING STARTED (cont.)
16
EN
NOTES about S-VHS and S-VHS ET
Ⅲ JVC EHG (Extra High Grade) tapes are recommended for superior results.
Use S-VHS tape for storing recordings for an extended period or for recording important scenes, as it
enables higher-quality recording and playback.
Ⅲ With some tapes, better picture quality may not be obtained even with S-VHS ET recording. It is
recommended that you do test record beforehand to make sure whether better results can be obtained.
Ⅲ If the S-VHS ET mode or recording format is switched during recording, the playback picture will be
blurred at the switching point.
Ⅲ It is recommended that tapes recorded in the SP mode on this camcorder be played back on this
camcorder.
Ⅲ Noise may appear on-screen when tapes recorded in the EP mode are played back.
Ⅲ Tapes recorded in S-VHS or S-VHS ET mode can be played back not only on this camcorder but also on
a Super VHS VCR or a VCR equipped with the SQPB (S-VHS QUASI PLAYBACK) function.
— When tapes recorded in S-VHS or S-VHS ET mode are played back on a VCR equipped with the
SQPB (S-VHS QUASI PLAYBACK) function, S-VHS picture quality is not available.
— Tapes recorded in S-VHS ET mode cannot be played back on some VCRs, including some JVC VCRs
(eg: HR-S6600U, HR-SC1000U, etc.).
Ⅲ Tapes recorded in S-VHS or S-VHS ET mode cannot be played back correctly on a normal VHS VCR.
Ⅲ You can play back S-VHS ET recordings not only on this VCR but also on another VHS VCR equipped
with S-VHS ET.
— It is recommended to specifically label S-VHS ET recordings so you can easily distinguish them from
regular VHS recordings.
Ⅲ S-VHS ET does not work with S-VHS tapes.
Ⅲ To avoid on-screen noise, do not perform Still Playback or Shuttle Search repeatedly.
Ⅲ If the picture contains a lot of jitter or noise, use a cleaning cassette.
Compatibility Between S-VHS And VHS
Recording
Playback
Blank tape
Camcorder
Recorded tape
Cassette adapter
S-VHS VCR
VHS VCR with SQPB
function
S-VHS-C
cassette
S-VHS
recordings
•The recorded format (S-VHS or
VHS) is automatically detected
when playback begins.
VHS-C
cassette
VHS
recordings
Regular VHS VCR
Blank tape
Camcorder
Recorded tape
Cassette adapter
•S-VHS recorded tapes cannot be
viewed on regular VHS VCRs,
other than those equipped with the
SQPB (S-VHS QUASI PLAYBACK)
function.
EN17
Grip Adjustment
Power Zoom Lever
Separate the Velcro strip.
1
2
3
Recording
Start/Stop Button
Pass your right hand through the loop and grasp the
grip.
Adjust so that your thumb and fingers can easily
operate the Recording Start/Stop Button and Power
Zoom Lever. Refasten the Velcro strip.
3
Viewfinder Adjustment
2
Set the Power Switch to “CAMERA” (“AUTO” or
180°
1
2
3
“PRO.”).
Adjust the viewfinder manually for best viewability.
1
Turn the Diopter Adjustment Control until the
indications in the viewfinder are clearly focused.
Set to “CAMERA”
(“AUTO” or “PRO.”).
PAUSE
Shoulder Strap Attachment
Following the illustration, thread the strap through the
1
eyelet 1, then fold it back and thread it through the
buckle 2. Repeat the procedure to attach the other
end of the strap to the other eyelet 3, making sure
the strap is not twisted.
1
4
2
Adjust as shown in the illustration 4.
2
3
Tripod Mounting
Align the screw and camera direction stud on the
tripod with the camera’s mounting socket and stud
hole. Then tighten the screw.
1
CAUTION:
When using a tripod, be sure to open and extend
its legs fully to stabilize the camcorder. To
prevent damage to the unit caused by falling
over, do not use a small-sized tripod.
BASIC VIDEO RECORDING
18
EN
NOTE:
LENS COVER Open/Close Ring
You should already have performed the procedures listed
below. If not, do so before continuing.
● Power (੬ pg. 10)
● Recording Mode Setting (੬ pg. 14)
● Load A Cassette (੬ pg. 12)
● Grip Adjustment (੬ pg. 17)
● Viewfinder Adjustment (੬ pg. 17)
System Select
Switch
Shooting While Watching The
Viewfinder
Power Switch
Recording Start/Stop Button
Make sure the LCD monitor is closed and locked.
1
Turn the LENS COVER Open/Close Ring to open the
lens cover. Set the System Select Switch to “VIDEO”,
then set the Power Switch to “CAMERA” (“AUTO” or
“PRO.”). The power lamp lights and the camcorder
enters the Record-Standby mode. “PAUSE” is
displayed in the viewfinder.
2 5M I N
Tape remaining time
indicator
(Approximate)
Press the Recording Start/Stop Button. “
” appears
MIN
120MIN
1MIN
119MIN
2
in the viewfinder while recording is in progress.
(Now calculating)
0MIN
(Blinking)
2MIN
(Blinking)
3MIN
(Blinking)
Shooting While Watching The
LCD Monitor
Make sure the LCD monitor is fully open. Turn the
1
LENS COVER Open/Close Ring to open the lens
cover. Set the System Select Switch to “VIDEO”, then
set the Power Switch to “CAMERA” (“AUTO” or
“PRO.”). The power lamp lights and the camcorder
enters the Record-Standby mode. “PAUSE” is
displayed in the LCD monitor.
90°
180°
Select Wheel (BRIGHT)
DISPLAY Button
Tilt the LCD monitor upward/downward for best
2
viewability and press the Recording Start/Stop Button.
“
” appears in the LCD monitor while recording is
–––––6–––––
+
BR I GHT
–
in progress.
NOTE:
When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, use the viewfinder instead.
To Adjust The Brightness Of The LCD Monitor
.... rotate the Select Wheel (BRIGHT) until the
bright level indicator on the display moves
and the appropriate brightness is reached.
To Stop Recording . . .
.... press the Recording Start/Stop Button. The camcorder
re-enters the Record-Standby mode.
Power Switch Position
AUTO : Suitable for standard recording using NO special effects or manual adjustments.
PRO. : Allows you to set recording functions using the menus for more creative capabilities.
OFF : Switches off the camcorder.
PLAY : Allows you to play back your recordings.
EN19
NOTES:
● When the Power Switch is set to CAMERA and the LCD monitor is opened at an angle of 60 degrees or more,
the LCD monitor switches on and the viewfinder switches off automatically to save power.
● The cassette holder cannot be opened unless a power supply is attached.
● There may be a delay after you slide EJECT until the cassette holder opens. Do not use force.
● The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
● The tape remaining time indicator is correct only if the correct tape length has been selected (੬ pg. 14).
● “TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this
condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is loaded.
● If the Record-Standby mode continues for 5 minutes without performing Zoom or any other operations, the
camcorder’s power shuts off automatically. Set the Power Switch to “OFF”, and then back to “CAMERA” to
turn the camcorder on again.
● If the Recording Start/Stop button is pressed after the Record-Standby mode has continued for over 5 minutes,
recording may not start immediately.
● If you are recording on a cassette from the middle (such as when a tape is removed and re-inserted during
recording), use the Retake function (੬ pg. 26) to find the end of the last recording so you do not erase any
of it.
● While shooting, sound is not heard from the speaker.
JOURNALISTIC SHOOTING
In some situations, different shooting angles may provide
more dramatic results. Hold the camcorder in the desired
position and tilt the LCD monitor in the most convenient
direction. It can rotate 270° (90° downward, 180° upward).
INTERFACE SHOOTING
The person you shoot can view himself/herself in the LCD
monitor, and you can even shoot yourself while viewing your
own image in the LCD monitor.
Open the LCD monitor and tilt it upward to 180 degrees so
that it faces forward. When the LCD monitor is tilted upward
to an angle of over approx. 105 degrees, the monitor image is
inverted vertically, and the viewfinder also switches on.
Point the lens toward the subject (yourself when self-
recording) and start recording.
During Interface Shooting, the monitor image and indications
do not appear inverted as they would when viewing a mirror.
NOTE:
The monitored image can be viewed on the LCD monitor
and in the viewfinder.
LCD MONITOR/VIEWFINDER INDICATIONS
Press DISPLAY for more than 1 second to make the following
indications appear/disappear from the camcorder’s display:
cassette warning, tape remaining time, battery pack remaining
power indicator and tape length indicator (੬ pg. 62, 63).
NOTE:
Even if the indications are off, the tape remaining time
appears blinking when the tape is near its end, and the
battery pack remaining power indicator appears blinking
when the power is almost gone.
Self-Recording
EN BASIC DIGITAL STILL CAMERA (D.S.C.) SHOOTING
20
When shooting a still image, it is not recorded onto the
tape, but it is stored in the camcorder's built-in memory in
the selected Picture Mode. A stored still image data can be
transferred to a PC, saved, and processed using a Paint
Software program (੬ pg. 45).
LENS COVER Open/Close Ring
SNAPSHOT Button
A still image processed on the PC can be also inserted
onto a tape (੬ pg. 55).
System
Select Switch
MODE SELECTION
Turn the LENS COVER Open/Close Ring to open the
1
lens cover, then set the System Select Switch to
“D.S.C.”. Set the Power Switch to “PRO.”. The power
lamp lights and an image appears.
Select Wheel
To select the Picture Mode, perform steps 2 and 3 of
Power Switch
MENU Button
2
3
“OPERATION” on pg. 22.
Rotate the Select Wheel to move the highlight bar to
“SNAPSHOT”, and press it. The SNAPSHOT Menu
appears.
Rotate the Select Wheel to move the highlight bar to
the appropriate mode among the 4 Snapshot modes
(੬ pg. 21), and press it. Selection is complete.
Display
TELE MACRO
OFF
TAPE LENGTH
P I CTURE
SNAPSHOT
T3 0
STANDARD
FULL
Menu Screen
The Menu Screen reappears with the highlight bar on
“RETURN”. Press the Select Wheel again to close the
Menu Screen.
4
4
RETURN
SNAPSHOT
SNAPSHOT Menu
STILL IMAGE STORAGE
FULL
–
P I N UP
–
–
MULT I
4
9
Press SNAPSHOT.
MULT I
1
•Regardless of the Power Switch position (“AUTO”
or “PRO.”), Snapshot recording takes place using
the selected Snapshot mode.
EX I T
•A still image is stored in the built-in memory and
displayed for approx. 2 seconds. While the still
image remains displayed, that image is in the
process of being stored in memory, and it is
therefore impossible to take another shot during that
time. When the still image disappears and the scene
you are currently aimed at appears on the screen,
you may take another shot.
TELE MACRO
OFF
TAPE LENGTH
P I CTURE
SNAPSHOT
T3 0
Menu Screen
STANDARD
–
P I N UP
4
RETURN
Normal Screen
•The remaining number of shots available is
displayed.
Snapshot mode
P
EN21
NOTES:
STD 3 4
Remaining number
of shots
● The remaining number of shots varies according to the
selected Picture Mode. In the “STANDARD” mode,
twice as many still images can be shot as in the “FINE”
mode.
60 59
1
0
(Blinking)
● Some sample images have been stored in the built-in
memory at the factory. If you wish to delete them, first
remove the “Protect” function (੬ pg. 49), then perform
the “Delete” function (੬ pg. 50).
Pictrue mode
display
● When the Power Switch is set to “AUTO”, it is not
possible to select the Snapshot mode. You can use the
Snapshot mode you selected in the “PRO.” mode.
● If a Snapshot is taken while the camcorder is in the
WIDE mode (੬ pg. 31), the Snapshot image is
recorded without the black bars at the top and bottom of
the screen.
FULL*
(Snapshot mode
with no frame)
● When the remaining number indicator displays “0”
(blinking), it is not possible to continue storing pictures
until you delete some shots to make room for new ones.
Perform “DELETE” function in the Menu Screen to
remove pictures you do not need (੬ pg. 50).
● When SNAPSHOT is pressed with the System Select
Switch set to “VIDEO”, the picture is stored in the
camcorder's built-in memory (in the Snapshot mode
selected in the “VIDEO” system) and also onto the tape
(if a tape is in the camcorder) (੬ pg. 23).
PIN-UP*
(Pin-Up mode)
● When you shoot in a dark environment, the still image
will become coarse and its true colors will be lost.
MULTI-4 **
(Multi-Analyzer 4)
* There is a momentary camera shutter-type blackout
together with the image.
** Continuous camera shutter-type blackout takes place 4
or 9 times with the image, like serial photography, then
the 4 or 9 still images you took are displayed.
MULTI-9**
(Multi-Analyzer 9)
CONTINUED ON NEXT PAGE
BASIC D.S.C. SHOOTING
22
EN
FEATURE: Picture Mode Setting
PURPOSE:
System
Select Switch
There are two image settings you can choose from
when storing in the camcorder's memory: FINE and
STANDARD. FINE allows you to shoot up to approx.
30 still images in a format based on JPEG (Joint
Photographic Experts Group). Since the quality of
image is better than “STANDARD”, “FINE” is more
suitable for post-production on a PC. “STANDARD”
allows you to shoot up to approx. 60 still images in a
format based on JPEG (Joint Photographic Experts
Group). Since in this mode, twice as many still images
can be shot as in the “FINE” mode, select this mode
when you wish to shoot many still images.
Select Wheel
Power Switch
MENU Button
OPERATION:
1) Set the System Select Switch to “D.S.C.”. Set the
Power Switch to “PRO.”.
Display
TELE MACRO
OFF
2) Press MENU. The Menu Screen appears.
3) Rotate the Select Wheel to move the highlight bar to
“PICTURE”, and press it. The PICTURE Menu
appears.
TAPE LENGTH
P I CTURE
T3 0
STANDARD
FULL
Menu Screen
SNAPSHOT
4
RETURN
Rotate the Select Wheel to move the highlight bar to
“FINE” or “STANDARD”, and press it. Selection is
complete.
4) The Menu Screen reappears with the highlight bar
on “RETURN”. Press the Select Wheel again to close
the Menu Screen.
P I CTURE
PICTURE Menu
F I NE
STANDARD
EX I T
NOTES:
● The picture mode’s factory-preset is STANDARD.
● To store the still images you shot, we recommend that
you transfer them to a computer and save them on disk
(੬ pg. 45), or transfer them to a VCR connected to the
camcorder and record them onto a tape.
TELE MACRO
OFF
TAPE LENGTH
P I CTURE
SNAPSHOT
T3 0
Menu Screen
F I NE
–
P I N UP
4
RETURN
● When the Power Switch is set to “CAMERA” (“AUTO”
or “PRO.”) and the LCD monitor is opened at an angle
of 60 degrees or more, the LCD monitor switches on and
the viewfinder switches off automatically to save power.
When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, use the viewfinder instead.
Normal Screen
● The Picture Mode can be switched to either “FINE”or
“STANDARD”. Since the remaining number of shots
available depends on the selected Picture Mode,
switching the Picture Mode will vary this number.
RECORDING Basic Features
EN23
LENS COVER Open/Close Ring
Snapshot
This interesting feature lets you record two types of digital
still images that look like photographs onto a tape, as well
as keeping them in the camcorder’s built-in memory. It is a
great way to spice up footage of events such as parties,
weddings and graduations.
SNAPSHOT Button
System
Select Switch
SNAPSHOT MODE SELECTION
Turn the LENS COVER Open/Close Ring to open the
1
2
lens cover, and set the System Select Switch to
“VIDEO”. Set the Power Switch to “PRO.”
The power lamp lights and the camcorder enters
Record-Standby mode.
Select Wheel
Power Switch
Press MENU. The Menu Screen appears.
Rotate the Select Wheel to move the highlight bar to
“SNAPSHOT”, and press it. The SNAPSHOT Menu
appears.
MENU Button
Rotate the Select Wheel to move the highlight bar to
“FULL” or “PIN-UP”, and press it. Selection is
complete.
Display
TELE MACRO
OFF
TAPE LENGTH
P I CTURE
T3 0
STANDARD
FULL
Menu Screen
The Menu Screen reappears with the highlight bar on
“RETURN”. Then press the Select Wheel to close the
Menu Screen.
SNAPSHOT
3
4
RETURN
SNAPSHOT
SNAPSHOT Menu
FULL
–
P I N UP
EX I T
TELE MACRO
OFF
TAPE LENGTH
P I CTURE
SNAPSHOT
T3 0
Menu Screen
STANDARD
–
P I N UP
4
RETURN
CONTINUED ON NEXT PAGE
RECORDING Basic Features (cont.)
SNAPSHOT RECORDING
Press SNAPSHOT.
24
EN
SNAPSHOT
1
•Regardless of the Power Switch position (“AUTO”
or “PRO.”), Snapshot recording takes place using
the selected Snapshot mode.
•A still image is recorded onto the tape and into the
camcorder’s built-in memory.
•First there is a momentary camera shutter-type
blackout together with the sound effect of a shutter
closing, then a still image appears. The scene you
are currently aimed at starts in the center of a black
screen and wipes in toward the corners.
The screen changes as shown in the illustrations 1
to 5 and the screens 1 to 5 are recorded onto the
tape in the selected mode. Only the still image 3 is
stored in the built-in memory in the selected mode,
then the camcorder resumes normal recording.
Display (ex. Pin-Up)
1
2
3
4
5
If you press during Record-Standby mode . . .
.... the screens 1 to 3 are recorded onto the tape in
the selected mode. Then the camcorder re-enters
the Record-Standby mode.
NOTES:
● When the remaining number indicator displays “0”
(blinking), the still image will be recorded onto the tape
but not in the built-in memory. If you wish to store a still
image in the built-in memory, ੬ pg. 50.
● The Picture Mode can be switched to either “FINE” or
“STANDARD”. Since the remaining number of shots
available depends on the selected Picture Mode,
switching the Picture Mode will vary this number.
● If SNAPSHOT is pressed with the System Select Switch
set to “D.S.C.”, ੬ pg. 20.
● Image data stored in the camcorder’s built-in memory
can be transferred to a Windows® PC and saved using
the provided image transfer software, Picture Navigator
(੬ pg. 45). The image data transferred to a Windows®
PC can also be further processed using Mr. Photo Gold.
● If a snapshot is taken while the camcorder is in the
WIDE mode (੬ pg. 31), the snapshot image is recorded
without the black bars at the top and bottom of the
screen.
● When a Snapshot is taken in a dark environment, the
still image recorded onto the tape and stored in memory
will become coarse and its true colors will be lost.
● The Snapshot mode can also be used during playback.
However, only the Full mode is available regardless of
the Snapshot mode setting, and the shutter sound is not
heard.
FULL
(Snapshot mode
with no frame)
PIN-UP
(Pin-Up mode)
EN25
FEATURE: Zooming
Zoom in (T: Telephoto)
PURPOSE:
To produce the zoom in/out effect, or an instantaneous
change in image magnification.
Digital circuitry extends the maximum magnification
offered by optical zoom. This system is called Digital
Zoom.
Zoom out (W: Wide angle)
Zoom indicator bar
OPERATION:
Zoom In
Slide the Power Zoom Lever towards “T”.
Zoom Out
Slide the Power Zoom Lever towards “W”.
Ⅲ The further you slide the Power Zoom Lever, the
quicker the zoom action.
Display
1X
Zoom level
indicator
NOTES:
● Focusing may become unstable during Zooming. In
this case, set the zoom while in Record–Standby,
lock the focus by using the manual focus
(੬ pg. 37), then zoom in or out in Record mode.
● The zoom level indicator (5) moves during zoom.
Once the zoom level indicator reaches the top of
the zoom indicator bar, all magnification from that
point is through digital processing.
Approximate
zoom ratio
Picture stabilizer indicator
Power Zoom Lever
● When using Digital Zoom, the quality of image may
suffer. To deactivate Digital Zoom, set “D.ZOOM”
to “OFF” in the Menu Screen (੬ pg. 31).
P. STABILIZER Button
FEATURE: Picture Stabilizer
PURPOSE:
To compensate for unstable images caused by camera-
shake, particularly at high magnification.
OPERATION:
Press P. STABILIZER. “ ”appears.
Ⅲ To switch off the Picture Stabilizer, press
P. STABILIZER. The indicator disappears.
NOTES:
● Accurate stabilization may not be possible if hand
shake is excessive, or under the following conditions:
•When shooting subjects with vertical or horizontal
stripes.
•When shooting dark or dim subjects.
•When shooting subjects with excessive backlighting.
•When shooting scenes with movement in various
directions.
•When shooting scenes with low-contrast backgrounds.
● Switch off the Picture Stabilizer when recording
with the camcorder on a tripod.
● The “
” indicator appears blinking if the
Stabilizer cannot be used.
RECORDING Basic Features (cont.)
26
EN
FEATURE: Quick Review (for scenes
recorded onto a tape)
RETAKE
PURPOSE:
To check the end of the last recording.
(
2/3)
Button
OPERATION:
1) Set the System Select Switch to “VIDEO”, then set the
Power Switch to “CAMERA” (“AUTO” or “PRO.”).
2) Press
2
and release quickly during the Record–
Standby mode.
Stop (5) Button
Play/Pause (4/6) Button
Ⅲ Tape is rewound for approx. 2 seconds and played
back automatically, then pauses in Record–Standby
mode for the next shot.
NOTE:
Distortion may occur at the start of playback. This is
normal.
FEATURE: Quick Review (for still
images stored in the
built-in memory)
PURPOSE:
To check the still image most recently stored in the
built-in memory.
OPERATION:
1) Set the System Select Switch to “D.S.C.”, then set the
Power Switch to “CAMERA” (“AUTO” or “PRO.”).
2) Press
2
and release quickly.
Ⅲ The still image is displayed for approx. 3 seconds.
The message “DELETE OK? PRESS PLAY BUTTON”
appears.
To remove the still image you have checked (Instant
Delete) . . .
1) Press 4/6. The still image is deleted.
To cancel, press 5.
FEATURE: Retake
PURPOSE:
To re-record certain segments.
OPERATION:
1) Make sure the camcorder is in the Record–Standby
mode.
2) Press and hold either RETAKE to reach the start point
for new recording. Pressing
3
forwards the tape
and pressing reverses it.
2
3) Press the Recording Start/Stop Button to start
recording.
NOTE:
Noise bars appear and pictures may become
monochrome or darken during Retake. This is normal.
EN27
FEATURE: Video Light
PURPOSE:
To brighten the scene when natural lighting is too dim.
OPERATION:
Set LIGHT OFF/AUTO/ON as required:
OFF : Turns off the light.
AUTO : Automatically turns on the light when the
camcorder senses insufficient lighting on the
subject.
ON
: Always keeps the light on as long as the
camcorder is turned on.
LIGHT OFF/AUTO/ON Switch
Ⅲ The video light can only be used with the
camcorder’s power on.
Ⅲ It is recommended to set the white balance
(੬ pg. 38) to
when you use the video light.
Ⅲ When not using the video light, turn it off to save
DANGER
battery power.
Ⅲ The video light can become extremely
hot. Do not touch it either while in
operation or soon after turning it off,
otherwise serious injury may result.
Ⅲ Do not place the camcorder into the
carrying case immediately after using the
video light, since it remains extremely
hot for some time.
NOTES:
● Even if the battery indicator (
) does not blink if
the battery pack’s charge is low, the camcorder may
turn off automatically when you turn on the video
light, or when you start recording with the video light
turned on.
● When LIGHT OFF/AUTO/ON is set to “AUTO”:
•Depending on the lighting conditions, the video
light may keep turning on and off. In this case,
manually switch the light on or off using LIGHT
OFF/AUTO/ON.
•While the “Sports” or “High Speed Shutter” mode
(੬ pg. 29) is engaged, the light is likely to stay on.
•While the “Twilight” mode (੬ pg. 29) is engaged,
the light will not activate.
Ⅲ When operating, keep a distance of
about 30 cm (11-13/16") between the
video light and people or objects.
Ⅲ Do not use near flammable or explosive
materials.
Ⅲ It is recommended that you consult your
nearest JVC dealer for replacing the video
light.
RECORDING Advanced Features
28
EN
Fade/Wipe Effects
These effects let you make pro-style scene transitions.
Fade- or wipe-in works at recording start, and fade- or
wipe-out works at recording end or when you enter
Record–Standby mode.
EFFECT
Button
Set the System Select Switch to “VIDEO”, and set the
System Select
Switch
1
2
Power Switch to “PRO.”.
Press EFFECT repeatedly until the desired mode’s
name and indication appear.
Power Switch
They are displayed for approx. 2 seconds, then the
3
name disappears so that only the indication remains.
The effect is reserved.
Recording Start/Stop Button
Press the Recording Start/Stop Button to activate fade-
in/out or wipe-in/out.
3
4
To cancel a fade or wipe, press EFFECT repeatedly
until “OFF” appears.
“OFF” is displayed for approx. 2 seconds and the
fade/wipe standby mode is canceled.
FADER
Fades in/out to a black screen.
MOSAIC (Fader)
Gradually turns/returns the picture into/from a mosaic
pattern.
SHUTTER (Wipe)
A black screen moves in from the top and bottom, closing
over the image like a shutter, or a new image pushes open
the black screen vertically from the center.
SLIDE (Wipe)
A black screen moves in from the left to gradually cover
the image, or a new image moves in from right to left.
DOOR (Wipe)
Wipes in as the two halves of a black screen open to the
left and right, revealing the scene, or wipes out and the
black screen reappears from left and right to cover the
scene.
NOTES:
● Pressing and holding the Recording Start/Stop
Button allows you to vary the length for the
image during fade in/out or wipe in/out.
● The screen becomes slightly reddish when
the Fade/Wipe is used with Sepia (੬ pg. 29).
● With the Electronic fog filter mode
(੬ pg. 29) engaged, the image fades in/out
to a white screen.
CW:CORNER (Wipe)
Wipes in on a black screen from the upper right to the
lower left corner, or wipes out from lower left to upper
right, leaving a black screen.
● Even if you start shooting with the Fade/Wipe
indication displayed during Digital Still
Camera Shooting, the Fade/Wipe does not
function.
WW:WINDOW (Wipe)
The next scene gradually wipes in from the center of the
screen toward the corners, covering the previous scene.
EN29
Program AE With Special Effects
Set the System Select Switch to “D.S.C.” or “VIDEO”,
and set the Power Switch to “PRO.”.
P.AE
1
2
Button
Press P.AE repeatedly until the desired mode’s name
and indication appear.
They are displayed for approx. 2 seconds, then the
name disappears so that only the indication remains.
The mode is activated.
System Select
Switch
To cancel the effect, press P.AE repeatedly until “OFF”
Power Switch
3
appears. “OFF” is displayed for approx. 2 seconds.
NOTES:
● Only one mode can be engaged at a time.
● The screen becomes slightly reddish when the Fade/
Wipe (੬ pg. 28) is used in the Sepia mode.
● The screen becomes slightly dark in the High Speed
Shutter mode. Use in well-lit situations.
● In the “High Speed Shutter” or “Sports” modes, picture
color may be adversely affected if the subject is lit by
alternating discharge-type light sources such as
flourescent or mercury-vapor lights.
SEPIA
TWILIGHT
The scene being shot is recorded in sepia-tinted
(reddish-brown) monochrome, giving the effect of
an older movie. Use together with Wide (੬ pg. 31)
for the authentic look of a classic Hollywood
movie.
Dusk, twilight scenery, fireworks, etc., look more
natural and dramatic. The following happens when
Twilight mode is selected:
•Auto gain control is turned off.
•White Balance is set to “
:FINE” (day mode),
but can also be manually changed to another
mode (੬ pg. 38).
SPORTS
•Auto Focus becomes available only in the range of
10 m (32 ft.) to infinity. To focus when the subject-
to-camera distance is less than 10 m (32 ft.), use
manual focusing (੬ pg. 37).
High shutter speed clearly captures fast-moving
action.
ND:ND EFFECT
A black mist darkens the picture, as when an ND
filter is used. Helps to counter the effects of glare on
the subject.
S1/2000
Captures faster action than Sports mode.
NEGA POSI
FG:FOG
The colors of a picture are reversed.
Makes the picture look misty white, as when an
external fog filter is attached to the lens. Softens the
image and gives it a “fantasy” look.
NEGA POSI mode
RECORDING Advanced Features (cont.)
30
EN
Using Menus For Detailed Adjustment
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of the more
detailed camcorder settings.
System Select Switch
The operation system depends on the function you
1
wish to select.
Set the System Select Switch to “VIDEO” or “D.S.C.”
according to each function’s “*/**” explanation
described at the bottom of pages 31 and 32, and set
the Power Switch to “PRO.”.
Select Wheel
Display
MENU Button
Menu access depends on the function you select.
2 If you select the functions from the “Menu Screen
(ex. Menu Screen available using the MENU Button)
Available Using The Select Wheel” described on
Menu Screen 1
pg. 31 . . .
4
NEXT
D. ZOOM
ON
OFF
ON
.... press the Select Wheel. The Menu Screen
appears.
TELE MACRO
If you select the functions from the “Menu Screen
Available Using The MENU Button” described on
pg. 31 and 32 . . .
4
BACK
REC T I ME
OFF
Menu Screen 2
I NT. T I ME
T I TLE LANG.
DATE / T I ME
JL I P I D NO.
DEMO MODE
OFF
.... press MENU. The Menu Screen appears.
ENGL I SH
0 6
OFF
Rotate the Select Wheel to place the highlight bar on
the desired function.
3
4
4
RETURN
•To go from Menu Screen 1 to Menu Screen 2, rotate
the Select Wheel to “NEXT” and press it. To go back
to Menu Screen 1 from Menu Screen 2, rotate the
Select Wheel to “BACK”, and press it.
•To return to the previous setting, place the highlight
bar on “RETURN”, then go to step 6.
Setting Menu
(ex. TITLE LANG.)
T I TLE LANG.
ENGL I SH
FRENCH
SPAN I SH
PORTUGUESE
Press the Select Wheel. The setting procedure
depends on the function you select.
EX I T
If you select “FOCUS”, “EXPOSURE”, “M.W.B.” or
“DATE/ TIME”. . .
.... see respective pages (FOCUS: ੬ pg. 37,
EXPOSURE: ੬ pg. 36, M.W.B.: ੬ pg. 38,
DATE/TIME: ੬ pg. 13) and perform each
procedure from step 4.
4
BACK
REC T I ME
OFF
I NT. T I ME
T I TLE LANG.
DATE / T I ME
JL I P I D NO.
DEMO MODE
OFF
FRENCH
0 6
OFF
If you select “JLIP ID NO.” . . .
.... rotate the Select Wheel until the desired number
appears, and press it. Then rotate the Select
Wheel to move the highlight bar to “EXIT”.
4
RETURN
Normal Screen
If you select any other functions . . .
.... rotate the Select Wheel to move the highlight bar
to the desired setting.
•To return to the previous setting, place the
highlight bar on “RETURN”.
NOTE:
Press the Select Wheel. The Menu Screen reappears
with the highlight bar on “RETURN”.
No menu functions except “FOCUS” and
“EXPOSURE” are available while in the Record
mode.
5
6
Press the Select Wheel. The normal screen reappears.
EN31
MENU SCREEN EXPLANATIONS
Menu Screen Available Using The Select Wheel
Refer to “Focusing” (੬ pg. 37).
FOCUS
Refer to “Exposure Control” (੬ pg. 36).
EXPOSURE
M.W.B.
Refer to “White Balance Adjustment” and “Manual White Balance Operation”
(੬ pg. 38).
OFF
ON
Does not display black bars.
WIDE
S.LX
Allows you to record black bars at the top and bottom of the screen
to produce a cinema-like “wide-screen” effect. If a snapshot
(੬ pg. 20, 23) is taken while the camcorder is in the WIDE
mode, the snapshot image is recorded without the black bars at
the top and bottom of the screen.
MAX
To record a subject in a darkly lit environment, when it is more
convenient to shoot the subject with a brighter image even if the
picture becomes slightly coarse.
NORMAL
To record a subject in a dimly lit environment, when it is more
convenient to shoot with a less coarse picture although the
subject becomes slightly dark. This setting is suitable for
measuring sensitivity conforming to EIA-639 (EIA* Standard for
Low Light Sensitivity Measurement).
*EIA : Electronic Industries Alliance
OFF
Allows you to shoot dark scenes with no picture brightness
adjustment.
Allows you to superimpose one of eight preset titles (੬ pg. 33).
TITLE*
Makes the date/time settings appear in the camcorder or on a connected monitor
(੬ pg. 33).
DATE/TIME
DISP.*
Menu Screen Available Using The MENU Button
This Menu Screen cannot be accessed while recording.
D. ZOOM
ON
Allows you to use the Digital Zoom. By digitally processing and
magnifying images, zooming is possible from 16X (the optical
zoom limit), to a maximum of 400X digital magnification.
OFF
Digital Zoom is not available. Only optical zoom (maximum
16x magnification) can function. When set to “OFF” during
Digital Zoom, zoom magnification changes to 16X.
TELE MACRO
OFF
ON
Usually the distance to a subject where the lens is in focus
depends on the zoom magnification. Unless there is a distance of
more than 1 m (3.25 ft.) to the subject, the lens is out of focus at
the maximum telephoto setting. When set to “ON”, you can
shoot a subject as large as possible at a distance of approx. 60 cm
(23-5/8").
•Depending on the zoom position, the lens may go out of focus.
* Activated only with the System Select Switch set to “VIDEO”. If the System Select Switch is set to “D.S.C.”,
this function will not be activated although the highlight bar will move on the Menu Screen like the setting
procedure.
Functions listed without an asterisk are available with the System Select Switch set to either “D.S.C.” or
“VIDEO”.
: Factory-preset
CONTINUED ON NEXT PAGE
RECORDING Advanced Features (cont.)
Menu Screen Available Using The MENU Button (cont.)
32
EN
S-VHS***
(S-VHS ET***)
ON
Records in S-VHS on a VHS or S-VHS cassette (੬ pg. 15).
OFF
Records in VHS on a VHS or S-VHS cassette (੬ pg. 15).
Allows you to set the tape length depending on the tape used (੬ pg. 14).
TAPE LENGTH*
PICTURE**
Refer to “Picture Mode Setting” (੬ pg. 22).
FULL
Displayed with the System Select Switch set to either “VIDEO”
SNAPSHOT
(੬ pg. 23) or “D.S.C.” (੬ pg. 21).
PIN-UP
MULTI-4
MULTI-9
Displayed only with the System Select Switch set to “D.S.C.”
(੬ pg. 21).
REC TIME*
Refer to “Animation” (੬ pg. 34) and “Time-Lapse” (੬ pg. 35).
INT. TIME
Refer to “Time-Lapse” (੬ pg. 35).
TITLE LANG.*
Allows you to select the language (ENGLISH, FRENCH, SPANISH or PORTUGUESE)
of Instant Titles (੬ pg. 33).
DATE/TIME
JLIP ID NO.
Allows you to set the current date and time (੬ pg. 13).
This number is necessary when connecting the camcorder to a device such as a computer
using the J terminal (JLIP). The numbers range from 01 to 99. Factory setting is 06.
DEMO MODE*
ON
Demonstrates certain functions such as Fade/Wipe, etc. When
“DEMO MODE” is set to “ON” and the Menu Screen is closed,
the demonstration starts.
Operating the Power Zoom Lever during the demonstration
stops the demonstration temporarily. If the Power Zoom Lever is
not moved for more than 1 minute after that, the demonstration
will resume.
NOTE:
When a tape whose Erase Protection tab is in the position that
allows recording is loaded in the camcorder, demonstration is
not available.
OFF
Automatic demonstration will not take place.
*
Activated only with the System Select Switch set to “VIDEO”. If the System Select Switch is set to “D.S.C.”,
this function will not be activated although the highlight bar will move on the Menu Screen like the setting
procedure.
** Activated only with the System Select Switch set to “D.S.C.”. If the System Select Switch is set to “VIDEO”,
this function will not be activated although the highlight bar will move on the Menu Screen like the setting
procedure.
Functions listed without */** are available with the System Select Switch set to either “D.S.C.” or “VIDEO”.
***S-VHS ET is displayed when a VHS cassette is loaded, and S-VHS is displayed when an S-VHS cassette is
loaded (੬ pg. 15). If a cassette is not loaded, “S-VHS” will be displayed in the Menu Screen.
S-VHS ET is preset to “OFF”.
: Factory-preset
EN33
Date/Time Insert
Set the System Select Switch to “VIDEO”, and set the
1
2
3
Power Switch to “PRO.”.
Allows you to display the date and time in the
camcorder or on a connected color monitor, as
well as to record them manually or
automatically.
Press the Select Wheel to display the Menu Screen.
You should have already performed the Date/
Time Setting procedure (੬ pg. 13).
Rotate the Select Wheel to move the highlight bar to
“DATE/TIME DISP.” while in Record-Standby, then
press it to display the Date/Time DISP. Menu.
Rotate the Select Wheel to move the highlight bar to
the desired mode, then press it. The desired mode is
activated.
4
5
System
Select Switch
The Menu Screen reappears with the highlight bar on
“RETURN”. Press the Select Wheel to close the Menu
Screen.
NOTES:
DISPLAY
Select Wheel
Power Switch
● The selected display can be recorded.
● If you do not want to record the display, select the OFF
mode before shooting.
● Even if you shoot with the date/time displayed during
Digital Still Camera Shooting, they will not be recorded.
DEC 2 5 . 9 9
AUTO DATE
AUTO DATE
● Your camcorder automatically records the date for about
5 seconds after recording is initiated in the following
situations:
DEC 25. 99
(DATE)
•After changing the date.
AM 10 : 25 : 00
(TIME)
•After loading a cassette.
•After Auto Date Record mode is selected by rotating
the Select Wheel.
● In this mode, the date is replaced after 5 seconds with
“AUTO DATE” but this is not recorded.
DEC 25. 99 AM 10 : 25 : 00
(DATE&TIME)
No indication
(OFF)
Instant Titles
Set the System Select Switch to “VIDEO”, and set the
1
2
3
Power Switch to “PRO.”.
The camcorder has eight preset titles in
memory. You can superimpose one of them
over the video image.
Press the Select Wheel to display the Menu Screen.
Instant Titles can be displayed not only in
English but also in French, Spanish and
Portuguese. Change the setting in TITLE LANG.
in the Menu Screen. (੬ pg. 30, 32).
Rotate the Select Wheel to move the highlight bar to
“TITLE” while in Record-Standby, then press it to
display the TITLE Menu.
T I TLE
OFF
Rotate the Select Wheel to move the highlight bar to
the desired mode, then press it. The desired mode is
activated.
HAPPY B I RTHDAY
OUR VACAT I ON
MERRY CHR I STMAS
4
A
SPEC I AL DAY
•To make the title indication disappear, select “OFF”.
HAPPY HOL I DAYS
OUR NEW BABY
WEDD I NG DAY
CONGRATULAT I ONS
EX I T
The Menu Screen reappears with the highlight bar on
“RETURN”. Press the Select Wheel to close the Menu
Screen.
5
NOTES:
● Even if you shoot with the Title displayed during Digital Still Camera Shooting, this is not recorded.
● The selected title will remain until OFF is selected in the TITLE Menu.
RECORDING Advanced Features (cont.)
34
EN
Animation
You can give stationary scenes or objects an illusion of
movement. This function allows you to shoot a series of
pictures, each slightly different, of the same object for a
brief period of time.
System
Select Switch
NOTES:
Before performing the following steps, make sure that:
● The System Select Switch is set to “VIDEO”.
● The Power Switch is set to “PRO.”.
● The camcorder is in the Record-Standby mode.
● The recording mode is set to “SP”.
Select Wheel
Recording
Start/Stop Button
Press MENU. The Menu Screen appears.
MENU Button
1
Rotate the Select Wheel to move the highlight bar to
2
“NEXT” in Menu Screen 1 and press it to display
Menu Screen 2. Then, move the highlight bar to
“REC TIME” and press it. The REC TIME Menu
appears. Rotate the Select Wheel to move the
highlight bar to the desired recording time, then press
it. The Menu Screen reappears with the highlight bar
on “RETURN”. Press the Select Wheel again to close
the Menu Screen.
Display
REC T I ME
REC TIME Menu
OFF
1 / 4
1 / 2
S
S
1
5
S
S
EX I T
Press the Recording Start/Stop Button after focusing
on the subject. The recording stops automatically
after the selected period of time.
3
Repeat step 3 for the desired number of pictures.
Recording time
indicator
4
5
1S
To release the Animation mode, set “REC TIME” in
the Menu screen to “OFF”.
REC TIME indication on the normal screen
EN35
Time-Lapse
You can record sequentially at preset time spans. Leaving
the camcorder aimed at a specific subject, you can record
subtle changes over an extended period of time.
System
Select Switch
NOTES:
Before performing the following steps, make sure that:
● The System Select Switch is set to “VIDEO”.
● The Power Switch is set to “PRO.”.
● The camcorder is in the Record-Standby mode.
● The recording mode is set to “SP”.
Select Wheel
Recording
Press MENU. The Menu Screen appears.
Start/Stop Button
1
MENU Button
Rotate the Select Wheel to move the highlight bar to
2
“NEXT” in Menu Screen 1 and press it. Menu Screen
2 appears with the highlight bar on “REC TIME” and
press it. The REC TIME Menu appears. Rotate the
Select Wheel to move the highlight bar to the desired
recording time, then press it. The Menu Screen
reappears.
Display
REC T I ME
REC TIME Menu
OFF
1 / 4
1 / 2
S
S
1
5
S
S
Rotate the Select Wheel to move the highlight bar to
“INT. TIME”, then press it. The INT. TIME Menu
appears. Rotate the Select Wheel to move the
highlight bar to the desired interval time, then press it.
The Menu Screen reappears with the highlight bar on
“RETURN”. Press the Select Wheel again to close the
Menu Screen.
3
EX I T
I NT. T I ME
INT. TIME Menu
OFF
1 5
3 0
1
S
S
M I N
M I N
Press the Recording Start/Stop Button. Recording and
intervals alternate automatically.
5
4
5
EX I T
To release the Time-Lapse mode, when “
displayed, press the Recording Start/Stop Button to
display “ ”, then set “REC TIME” and
“INT. TIME” in the Menu Screen to “OFF”.
” is not
Interval time
indicator
NOTES (for Animation and Time-Lapse):
● For best results, make sure the camcorder is secured
when shooting in Animation or Time-Lapse mode.
● Fade- or wipe-in/out cannot be performed during
Animation or Time-Lapse shooting.
1 5S
1S
Recording time
indicator
● Before performing other operations following Animation
or Time-Lapse recording, make sure the Animation or
Time-Lapse mode is deactivated.
INT. TIME and REC TIME indications on the normal
screen
● Animation and Time-Lapse are canceled when the
power is shut off or when the cassette is ejected.
RECORDING Advanced Features (cont.)
36
EN
Exposure Control
This feature automatically adjusts the iris for the best
available picture quality, but you can override it and make
the adjustment manually. Manual exposure adjustment is
recommended in the following situations:
System
Select Switch
•When shooting using reverse lighting or when the
background is too bright.
•When shooting on a reflective natural background such
as at the beach or when skiing.
•When the background is overly dark or the subject light.
Select Wheel
Set the System Select Switch to “D.S.C.” or “VIDEO”,
Power Switch
1
2
3
and set the Power Switch to “PRO.”.
Press the Select Wheel to display the Menu Screen.
Manual Exposure
Screen
0 0
Rotate the Select Wheel to move the highlight bar to
“EXPOSURE” and press it. The EXPOSURE Menu
appears.
Exposure control
level counter
Rotate the Select Wheel to move the highlight bar to
“MANU”, then press it. The Menu Screen disappears
and “00” (exposure control level counter) appears.
4
5
To brighten the image
To brighten the image, rotate the Select Wheel
upward. The exposure control level counter increases
(maximum +06).
To darken the image, rotate the Select Wheel
downward. The exposure control level counter
decreases (maximum –06).
+
06
–06
To darken the image
Press the Select Wheel. The setting is complete. The
Menu Screen reappears with the highlight bar on
“RETURN”.
6
7
Press the Select Wheel. The Menu Screen disappears
and the exposure control level counter reappers to
indicate the exposure is adjusted.
NOTES:
● To return to the factory setting, select “AUTO” in step 4.
● To re-adjust exposure, repeat the procedure from step 2.
EN37
Focus detection zone
Focusing
AUTO FOCUS
The camcorder’s Full Range AF system offers continuous
shooting ability from close-up to infinity. However, correct
focus may not be obtainable in the situations listed below
(in these cases use manual focusing):
•When two subjects overlap in the same scene.
•When illumination is low.*
•When the subject has no contrast (difference in bright-
ness and darkness), such as a flat, one-color wall, or a
clear, blue sky.*
•When a dark object is barely visible in the viewfinder.*
•When the scene contains minute patterns or identical
patterns that are regularly repeated.
•When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
•When shooting a scene with a high-contrast background.
NOTES:
● If the lens is smeared or blurred, accurate
focusing is not possible. Keep the lens clean,
wiping with a piece of soft cloth if it gets
dirty. When condensation occurs, wipe with
a soft cloth or wait for it to dry naturally.
● When shooting a subject close to the lens,
zoom out first (੬ pg. 25). If zoomed in in
the auto focus mode, the camcorder could
automatically zoom out depending on the
distance between the camcorder and the
subject. This does not occur with “TELE
MACRO” (੬ pg. 31).
* The low-contrast warning “
” appears
MANUAL FOCUS
If you are using the viewfinder, you should already have
made the necessary viewfinder adjustments (੬ pg. 17).
Set the System Select Switch to “D.S.C.” or “VIDEO”,
1
2
3
4
and set the Power Switch to “PRO.”.
System
Select Switch
Press the Select Wheel to display the Menu Screen.
Rotate the Select Wheel to move the highlight bar to
“FOCUS” and press it. The FOCUS Menu appears.
Rotate the Select Wheel to move the highlight bar to
“MANU”, then press it. The Menu Screen disappears
and “ ” and “ ” appear. The focus is locked at this
point.
Select Wheel
Power Switch
To focus on a farther subject, rotate the Select Wheel
upward. “ ” appears and blinks.
To focus on a nearer subject, rotate the Select Wheel
downward. “ ” appears and blinks.
5
Press the Select Wheel. The setting is complete. The
Menu Screen reappears with the highlight bar on
“RETURN”.
6
7
Press the Select Wheel. The Menu Screen disppears
and “
” reappears to indicate the focus is locked.
NOTES:
● To return to Auto Focus, select “AUTO” in step 4.
● To re-adjust Manual Focus, repeat the procedure from step 2.
● Be sure to focus the lens in the maximum telephoto position when you use the Manual Focus mode. If you
focus in on a certain subject in the wide-angle position, sharply focused images cannot be obtained when
zoomed in because the depth-of-field is reduced at longer focal lengths.
● When the focus level cannot be adjusted any farther or closer, “ ” or “ ” will blink.
RECORDING Advanced Features (cont.)
38
EN
White Balance Adjustment
Manual White Balance Operation
A term that refers to the correctness of color
reproduction under various lighting. If the white
Perform Manual White Balance when shooting under
various types of lighting.
balance is correct, all other colors will be accurately
reproduced.
The white balance is usually adjusted automatically.
However, more advanced camcorder operators
control this function manually to achieve a more
professional color/tint reproduction.
Follow steps 1 through 4 of the white balance
1
2
adjustment, and select “MWB”.
Hold a sheet of plain white paper in front of the
subject. Adjust zoom or position yourself so that
the white paper fills the screen.
Set the System Select Switch to “D.S.C.” or
Press the Select Wheel until “MWB” begins
blinking.
When the setting is completed, “MWB” stops
blinking, and the Menu Screen reappears with
the highlight bar on “RETURN”.
1
2
3
“VIDEO”, and set the Power Switch to “PRO.”.
3
Press MENU. The Menu Screen appears.
Rotate the Select Wheel to move the highlight
bar to “M.W.B.”, then press it. The Menu Screen
disappears and the M.W.B. Menu appears.
Press the Select Wheel again to close the Menu
Screen.
4
Rotate the Select Wheel to move the highlight
bar to the desired setting.
4
System Select Switch
“AUTO”
White balance is adjusted automatically (factory
preset).
“
: FINE”
Outdoors on a sunny day.
: CLOUD”
Outdoors on a cloudy day.
: HALOGEN”
“
White paper
“
A video light or similar type of lighting is used.
“MWB”
White balance is set manually.
Power Switch
MENU Button
Select Wheel
Press the Select Wheel. The Menu Screen
reappears with the highlight bar on “RETURN”.
Press the Select Wheel again to close the Menu
Screen.
5
To Change The Tint For Recording . . .
.... in step 2, substitute colored paper for white. The
white balance is adjusted based on the color,
changing the tint. Red paper = deeper green;
blue paper = orange; yellow paper = deeper
purple.
To Return To Automatic White Balance . . .
.... select “AUTO” in step 4. Or set the Power
Switch to “AUTO”.
NOTE:
White balance cannot be used when Sepia
(੬ pg. 29) is activated.
NOTES:
● In step 2, it may be difficult to focus on the white
paper. In such a case, adjust focus manually
(੬ pg. 37).
● A subject can be shot under various types of
lighting conditions indoors (natural, flourescent,
candlelight, etc.). Because the color temperature is
different depending on the light source, the subject
tint will differ depending on the white balance
settings. Use this function for a more natural result.
● Once you adjust white balance manually, the
setting is retained even if the power is turned off or
the battery removed.
VIDEO PLAYBACK Basic Playback
EN39
Power Zoom Lever (VOL.)
Load a tape (੬ pg. 12).
1
2
Set the System Select Switch to “VIDEO”, then set the
Power Switch to “PLAY”. To start playback, press
4/6.
Speaker
•To stop playback, press 5.
•Press
2
to rewind, or
3
to fast-forward the tape
during Stop mode.
NOTES:
● The camcorder shuts off automatically after about
5 minutes in Stop mode. To turn on again, set the Power
Switch to “OFF”, then to “PLAY”.
● When the Power Switch is set to “PLAY” and the LCD
monitor is opened at an angle of 60 degrees or more, the
LCD monitor switches on and the viewfinder switches
off automatically to save power.
Select Wheel
(BRIGHT)
Set to “PLAY”.
Set to “VIDEO”.
Rewind (2) Button
● The playback picture can be viewed in the viewfinder
(with the LCD monitor shut), on the LCD monitor or on
a connected TV (੬ pg. 42, 43).
● You can also view the playback picture on the LCD
monitor with it flipped over and retracted.
Fast-Forward (3) Button
Play/Pause (4/6) Button
● If a blank portion on the tape is played back, the screen
may become black. This is not a malfunction.
Stop (5) Button
LCD Monitor Brightness Adjustment: Rotate
the Select Wheel (BRIGHT) towards “+” to brighten, or
towards “–” to darken.
● The Bright Level Indicator is displayed under the Date/
Time Display when you play back images recorded in
Wide Mode (੬ pg. 31).
Speaker Volume Control: Slide the Power
Zoom Lever (VOL.) towards “+” to turn up the volume,
or towards “–” to turn down the volume.
● The Speaker Volume Indicator is displayed under the
Date/Time Display when you play back images recorded
in Wide Mode (੬ pg. 31).
Still Playback: Pauses during playback.
1) Press 4/6 during playback.
2) To resume normal playback, press 4/6 again.
● If TBC (੬ pg. 40) is not engaged, noise bars will appear
and the picture will become monochrome during Still
Playback.
● If TBC is engaged, noise bars will not appear. This mode
is called Fine Still.
Shuttle Search: Allows high-speed search in either
direction.
1) Press
playback.
2) To resume normal playback, press 4/6.
● During playback, press and hold or 3. The search
3
for forward or
2
for reverse search during
2
continues as long as you hold the button. Once you
release it, normal playback resumes.
● Noise bars appear and pictures may become mono-
chrome or darken during Shuttle Search. This is normal.
VIDEO PLAYBACK Features
Tracking: Eliminates noise bars that appear on-screen
during playback. Factory-preset is Auto Tracking.
To activate Manual Tracking:
40
EN
P.STABILIZER Button
1) Press P.AE and EFFECT simultaneously. “MT” appears.
2) Press P.AE or EFFECT as many times as necessary until
the noise bars disappear.
EFFECT Button
● To return to Auto Tracking, press P.AE and EFFECT
simultaneously. “AT” blinks. When Auto Tracking
finishes, the indication disappears.
P.AE Button
● When noise bars appear during playback, the
camcorder enters the Auto Tracking mode and “AT” is
displayed.
● Manual Tracking may not work with tapes recorded on
other VCRs or camcorders.
COUNTER R/M
Set to “PLAY”.
Set to “VIDEO”.
Button
TBC (Time Base Corrector): Removes jitter from
fluctuating video signals to deliver a stable picture even
with old tapes. Factory-preset: TBC is engaged.
To activate/release the TBC mode, press P.STABILIZER
during playback for more than 1 second. When the TBC
mode is activated, “TBC” is displayed.
Rewind (2) Button
Fast-Forward (3) Button
● The “TBC” indicator turns green (gray with a camcorder
equipped with a black/white viewfinder) while TBC is
working.
Play/Pause (4/6) Button
● TBC does not work during still playback and shuttle
search.
Stop (5) Button
● The “TBC” indicator turns white while TBC is not
operative.
● It may take a few seconds before TBC actually starts
working.
CLASSIC FILM
Gives recorded scenes a strobe effect.
● The picture may be distorted if the TBC mode is
activated or deactivated at the edit-in/-out points or
when normal playback resumes after still playback or
shuttle search.
● If the playback picture is distorted when TBC is set to
on, turn off TBC.
MONOTONE
Like classic black and white films, your
footage is shot in B/W. Used together with
the WIDE mode (੬ pg. 31), it enhances
the “classic film” effect.
SEPIA
Counter Memory Function: Makes it easier to
Recorded scenes have a brownish tint like
old photos. Combine this with the WIDE
mode for a classic look.
locate a specific tape segment.
1) Press COUNTER R/M and hold for more than 1 second.
The counter resets to “0:00:00”.
2) Press COUNTER R/M for less than 1 second. “M”
appears.
3) After recording or playback, press 5, then 2. The tape
automatically stops at or close to 0:00:00.
4) Press 4/6 to start playback.
● The counter memory functions in the Fast-Forward and
Rewind modes.
STROBE
Your recording looks like a series of
consecutive snapshots.
VIDEO ECHO
Adds a “ghost” to the subject, giving your
recording a “fantasy” feeling.
● To disable the Counter Memory Function, press COUN-
TER R/M for less than 1 second so that “M” disappears.
Playback Special Effects: Allows you to add creative effects to the playback image.
1) Activate the TBC mode and Auto Tracking.
2) Press P.AE repeatedly until the desired mode’s name and indication appear. They are displayed for approx. 2
seconds, then the name disappears so that only the indication remains. The effect is reserved.
3) To cancel the effect, press P.AE repeatedly until “OFF” appears. “OFF” is displayed for approx. 2 seconds.
● Playback Special Effects do not work during shuttle search.
● The selected effect mode cannot be changed during still playback.
VIDEO PLAYBACK Using The Cassette Adapter
Cassette Adapter (VHS Playpak)
EN41
Use this to play back an S-VHS-C/VHS-C video cassette
recorded with this camcorder on a VHS VCR. It is fully
compatible with any S-VHS/VHS video cassette recorder.
The C-P7U adapter is battery powered and automatically
performs tape loading and unloading.
Slide the battery cover up to remove it, install one
“AA (R6)” size battery as shown, then reattach the
cover.
1
2
Slide the latch to open the adapter compartment
door, then insert the cassette and close the compart-
ment door.
VCR
Load the cassette adapter into the VCR and play the
tape back as you would any other.
Compartment door
3
4
Slide the latch and the compartment door opens
automatically. This may take around 10 seconds. Do
not attempt to force the adapter open. Then, insert
your finger in the hole on the underside of the
adapter as shown in the illustration at left, and push
up and remove the cassette.
NOTES:
●During tape loading and unloading, do not touch the
reels for safety and tape protection.
●Tapes recorded in S-VHS or S-VHS ET mode cannot be
played back on a regular VHS VCR. Playback is possible
with a VCR equipped with the S-VHS or SQPB (S-VHS
QUASI PLAYBACK) function.
Sliding latch
Compact video cassette
●During special-effect playback (slow motion, still frame,
etc.), the picture may vibrate or noise bars may appear
on the screen.
Reels
●To record on a VCR using a compact cassette and the
adapter, cover the adapter’s recording safety hole with
adhesive tape.
Recording safety hole
BASIC CONNECTIONS
42
EN
These are some basic types of connections. When making connections, refer also to your VCR and TV
instruction manuals.
A.Connection to a TV or VCR equipped with an S-VIDEO IN and A/V input
connectors
TV
To Audio
Output
Audio cable
(optional)
To AUDIO IN
To TV or VCR
S-Video cable (optional)
To S-Video Output
To S-VIDEO IN
VCR
(Recording deck)
Connector cover*
B. Connection to a TV or VCR equipped only with A/V input connectors
TV
To Video
Output
To
Video cable
(optional)
VIDEO IN
To TV or VCR
Audio cable (optional)
To Audio Output
To AUDIO IN
VCR
(Recording deck)
Connector cover*
* When connecting the cables, open this cover.
EN43
Basic Connections
Tape Dubbing
Make sure all units are turned off.
Following the illustration on pg. 42, connect the
camcorder and the VCR.
1
2
1
2
Connect the camcorder to a TV or VCR as
Set the camcorder’s Power Switch to “PLAY”,
turn on the VCR’s power, and insert the
appropriate cassettes in the camcorder and the
VCR.
shown in the illustration (੬ pg. 42).
If using a VCR . . . go to step 3.
If not . . . go to step 4.
Connect the VCR output to the TV input,
referring to your VCR’s instruction manual.
Engage the VCR’s AUX and Record-Pause
modes.
3
4
5
3
4
Turn on the camcorder, the VCR and the TV.
Engage the camcorder’s Play mode to find a
spot just before the edit-in point. Once it is
reached, press 4/6 on the camcorder.
Set the VCR to its AUX input mode, and set the
TV to its VIDEO mode.
Press 4/6 on the camcorder and engage the
VCR’s Record mode.
5
6
7
NOTES:
Engage the VCR’s Record-Pause mode and press
4/6 on the camcorder.
● It is recommended to use the AC Power Adapter/
Charger as the power supply instead of the battery
pack (੬ pg. 11).
Repeat steps 4 through 6 for additional editing,
then stop the VCR and camcorder when
finished.
● If your VCR has an S-Video input connector,
connect the camcorder and the VCR using an
optional S-Video cable. This can improve the
dubbed picture quality.
NOTE:
If you wish to dub still images recorded with the
System Select Switch set to “D.S.C.”, play back the
still images (੬ pg. 44 – 48) instead of doing the
above steps 4 thorough 6, engage the VCR's Record
mode and record them onto a tape.
● To monitor the picture and sound from the
camcorder without inserting a tape, set the
camcorder’s Power Switch to “CAMERA” (“AUTO”
or “PRO.”), then set your TV to the appropriate
input mode.
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound
when the camcorder is turned on.
● If you have a TV or speakers that are not specially
shielded, do not place the speakers adjacent to the
TV as interference will occur in the camcorder
playback picture.
D.S.C. PLAYBACK Basic Playback
Still images shot using this camcoder are automatically
numbered, then stored in numerical order in the built-in
memory. You can view the still images stored in memory,
one at a time, much like flipping through a photo album.
44
EN
System
Select Switch
Set the System Select Switch to “D.S.C.”, and set the
1
2
Power Switch to “PLAY”. The power lamp lights and
a still image stored in memory is displayed.
•When no still image is stored in memory, the screen
becomes blue.
Next/Previous
Page (2/PAGE –
or 3/PAGE +)
Buttons
Press 3/PAGE+ or 2/PAGE– to select the still
image you want to view.
•Each time 2/PAGE– is pressed, the page goes
back, while each time 3/PAGE+ is pressed, the
page goes next.
•Even if you shoot a new picture after playing back a
still image with a low number, this will not
overwrite the existing picture because new pictures
are automatically stored after the still image most
recently stored in memory.
Power Switch
To move
the page next
Display
•If there are no stored images, “NO IMAGES
STORED” is displayed.
NOTES:
● When the Power Switch is set to “PLAY” and the LCD
monitor is opened at an angle of 60 degrees or more, the
LCD monitor switches on and the viewfinder switches
off automatically to save power.
● The playback picture can be viewed in the viewfinder
(with the LCD monitor shut), on the LCD moitor or on a
connected TV (੬ pg. 42).
● When viewing a playback picture on a connected TV, it
may jitter slightly.
● You can also view the playback picture on the LCD
monitor with it flipped over and retracted.
● To brighten the LCD monitor, rotate the Select Wheel
(BRIGHT) towards “+”. To darken the LCD monitor,
rotate it towards “–”.
To move
the page back
D.S.C. PLAYBACK Connection
EN45
Connection To A Windows® PC
Image data stored in the camcorder’s built-in memory can
be transferred to a Windows® PC and saved using the
provided image transfer software, Picture Navigator. The
image data transferred to a Windows® PC can also be
further processed using Mr. Photo Gold, and the still image
processed on the PC can be inserted onto a tape
(੬ pg. 55).
Set to
“D.S.C.”.
To assure safety, make sure all units are turned off before
making any connection.
To DIGITAL
connector
Connect the camcorder’s DIGITAL connector to the
1
COM Port (RS-232C) on a Windows® PC, using the
provided PC connection cable.
Set the System Select Switch to “D.S.C.”, then set the
Power Switch to “PLAY”. A still image stored in
memory appears.
•When transferring still images to a computer, be
sure that a still image is displayed on the screen.
PC connection cable
(provided)
2
For Windows®:
To COM Port
(RS-232C)
Launch the provided software on your Windows® PC.
Transfer the still images stored in the camcorder’s
memory to the Windows® PC. Refer to the software’s
instruction manual on the provided CD-ROM for
details.
3
•During transfer of the still image, the camcorder’s
screen becomes blue and “
” is dis-
played. After transferring is finished, the screen
displays the same still image as in step 2.
Close the software, then switch off the camcorder.
4
NOTES:
● Before transferring still images from your personal computer to the camcorder’s built-in memory, perform the
camcorder’s Picture Mode Setting (੬ pg. 22). The still images will be transferred from the personal
computer in the selected Picture Mode.
● When transferring still images from your personal computer to the camcorder, make sure the number of
images to be transferred is smaller than the camcorder's remaining number of shots available.
● Use the AC Power Adapter/Charger as the power supply instead of the battery pack.
● The still images stored in the camcorder’s memory are not automatically removed after being transferred to
the PC. If you wish to remove those still images from the camcorder's memory, delete them (੬ pg. 50, 51).
● Windows® are trademarks of Microsoft Corporation, registered in the U.S.A. and other countries.
D.S.C. PLAYBACK Advanced Features
46
EN
Using Menu For Detailed Adjustment
This camcorder is equipped with an easy-to-use,
on-screen menu system that simplifies many of the more
detailed camcorder settings.
System
Select Switch
Set the System Select Switch to “D.S.C.”, and set the
1
2
3
Power Switch to “PLAY”.
Press MENU. The Menu Screen appears.
Select Wheel
Rotate the Select Wheel to place the highlight bar on
the desired function.
•To return to the previous setting, place the highlight
bar on “RETURN”, then press the Select Wheel.
Power Switch
MENU Button
Press the Select Wheel. The setting menu of the
selected function appears. The setting procedure
depends on the function you select.
4
Display
Menu Screen
If you select “SLIDE SHOW ” . . .
.... a slide-show will start (੬ pg. 47).
If you select any other functions . . .
I NDEX
SL I DE SHO
PROTECT
DELETE
W
.... see respective pages (INDEX: ੬ pg. 48,
PROTECT: ੬ pg. 49, DELETE: ੬ pg. 50, 51)
and do each procedure from step 4.
4
RETURN
Setting Menu
(ex. PROTECT)
EXIT <PROTECT>
01
02
03
04
05
I NDEX
SL I DE SHO
W
PROTECT
DELETE
4
RETURN
Normal Screen
EN47
Menu Screen Explanations
Mode
Effect
INDEX
All still images stored in memory can be displayed six at a time. This mode is a
convenient way to look for the still image you want to view and to check the still
images you shot beforehand (੬ pg. 48).
SLIDE SHOW
After doing steps 1 through 4 on pg. 46, you can run through all the still images
stored in memory automatically in numerical order. Each still image is displayed.
This mode is like a regular slide-show. If you wish to stop the slide-show, press the
Select Wheel twice.
PROTECT
DELETE
Lets you protect selected still images from accidental erasure. Select a still image for
which you want to perform “Protect” to put a padlock mark next to it. A still image
with a padlock mark cannot be deleted. When selecting a still image to protect, you
can check six still images stored in memory at a time (੬ pg. 49).
Allows you to delete some still images already stored in memory (੬ pg. 50).
CAUTION:
While “ENTER” is selected on the Delete Execute Menu and it is blinking, switching
off the camcorder or removing the power supply unit (battery pack or AC Power
Adapter/Charger) may cause the camcorder’s built-in memory to become corrupt.
Never remove the power supply unit at this stage.
SELECT
Allows you to check 6 still images stored in memory at a time, to select
the still images you want to delete.
ALL
Allows you to delete all the still images at once except protected
images.
D.S.C. PLAYBACK Advanced Features (cont.)
48
EN
Index
You can view all still images stored in memory six at a
time. Use this mode when looking for a still image you
want to view and when checking the still images you shot
beforehand.
System
Select Switch
Set the System Select Switch to “D.S.C.”, and set the
1
2
3
4
Power Switch to “PLAY”.
Press MENU. The Menu Screen appears.
Select Wheel
Power Switch
MENU Button
Rotate the Select Wheel to move the highlight bar to
“INDEX” and press it. The “INDEX” Menu appears.
Rotate the Select Wheel to move the frame to the
desired still image, then press it. The one you selected
is displayed on the whole screen, then the screen
enters normal playback.
Display
EXIT
01
<INDEX>
02
•On the Index Menu, 6 still images are displayed at a
time. When viewing the still images that follow the
6th one, rotate the Select Wheel to move the frame
from Index No. 1 to No. 6, and then rotate it further
downward. The frame is placed on the 7th still
image automatically. Images after the 7th one can
also be accessed in the same way.
INDEX Menu
03
06
04
•If the desired still image cannot be found, place the
highlight bar on “EXIT”, then press the Select Wheel
twice to exit the Menu.
Playback Screen
NOTES:
● When moving the frame from the 7th still image back to
the 6th, rotate the Select Wheel upward to place the
highlight bar on “EXIT”, then rotate it further upward.
The frame is moved to the 6th still image. Perform the
same procedure for the 13th image.
● On the Index Menu, a star mark is displayed next to a
still image you shot in the FINE mode.
EN49
Protect
This mode helps prevent accidental erasure of images. Put
a padlock mark next to the desired still image, and that still
image cannot be deleted.
System
Select Switch
Set the System Select Switch to “D.S.C.”, and set the
1
2
3
Power Switch to “PLAY”.
Press MENU. The Menu Screen appears.
Select Wheel
Rotate the Select Wheel to move the highlight bar to
“PROTECT”, and press it. The PROTECT Menu
appears.
•If you do not want to perform “Protect” for any still
image, go to step 5.
Power Switch
MENU Button
Rotate the Select Wheel to move the frame to the
desired still image, then press it. The padlock mark
appears above the selected image. The “Protect”
function is set.
Display
4
EXIT <PROTECT>
PROTECT Menu
01
03
•On the Protect Menu, all still images are displayed
six at a time. To perform “Protect” for the still
images that come after the 6th one, rotate the Select
Wheel to move the frame from Index No. 1 to No.
6, then rotate it further downward. The frame is
placed automatically on the 7th still image. Images
after the 7th one can also be accessed in the same
way.
04
05
06
EXIT <PROTECT>
01
03
Rotate the Select Wheel upward to place the
highlight bar on “EXIT”, then press it twice. The
Menu Screen closes.
5
04
05
06
A padlock mark
appears.
To remove “Protect” . . .
.... perform steps 1 through 3, rotate the Select Wheel to
move the frame to the desired still image with the
padlock mark, then press it. The padlock mark located
above the still image disappears and the image is no
longer protected. When finished removing protection,
perform step 5.
NOTES:
● To move the frame from Index No. 7 to 6, place the
highlight bar on “EXIT” by rotating the Select Wheel
upward. Rotate the Select Wheel further upward. The
frame is moved to the 6th still image automatically.
Perform the same procedure for still images that follow
the 13th one.
● On the Protect Menu, a star mark is displayed next to a
still image you shot in the FINE mode.
D.S.C. PLAYBACK Advanced Features (cont.)
50
EN
Delete
When the memory in which still images are stored
becomes full, the number of remaining shots available
reaches “0” (blinking). In this situation it becomes
impossible to take your next shot. Delete some still images
already stored in memory to make room for new shots.
System
Select Switch
Set the System Select Switch to “D.S.C.”, and set the
1
2
3
4
Power Switch to “PLAY”.
Select Wheel
Press MENU. The Menu Screen appears.
Power Switch
MENU Button
Rotate the Select Wheel to move the highlight bar to
“DELETE”, and press it. The DELETE Menu appears.
Rotate the Select Wheel to move the highlight bar to
“SELECT” or “ALL”, then press it.
To select a still image by checking the still images
stored in memory . . .
Display
DELETE
DELETE Menu
SELECT
ALL
.... select “SELECT”. The Delete Select Menu
appears. Go to step 5.
To delete all the still images stored in memory at
once without checking them . . .
.... select “ALL”. The Delete Execute Menu appears.
Go to step 6.
In case of “ALL”
EX I T
To quit the Delete Mode . . .
.... rotate the Select Wheel to place the highlight bar
on “EXIT”, then press it twice.
NEXT <DELETE>
Delete Select
Menu
01
02
06
Rotate the Select Wheel to move the frame to the
desired still image, then press it. “ ” appears above
the selected still image. When you have finished
selecting all the desired still images, rotate the Select
Wheel upward to place the highlight bar on “NEXT”,
then press the Select Wheel.
04
05
5
In case of
“SELECT”
DELETE
Delete Execute
Menu
•On the Delete Select Menu, the still images are
displayed six at a time. To delete the still images
that follow the 6th one, rotate the Select Wheel to
move the frame from No. 1 to No. 6, then rotate it
further downward. The frame is moved to the 7th
still image automatically. Perform the same
CANCEL
ENTER
EX I T
procedure for still images that follow the 7th one.
Menu Screen
EN51
In case of “SELECT”
Rotate the Select Wheel to move the highlight bar to
6
7
“CANCEL” or “ENTER”, then press it.
NEXT <DELETE>
•“CANCEL” does not delete the selected still images
and the screen returns to the Menu Screen.
•“ENTER” deletes the selected still images. While
“ENTER” blinks, they are in the process of being
deleted from memory. After deleting is finished, the
screen returns to the Menu Screen.
01
02
06
04
05
Press the Select Wheel again to exit the Menu Screen.
CAUTION:
While “ENTER” is selected on the Delete
Execute Menu and it is blinking, switching off
the camcorder or removing the power supply
unit (battery pack or AC Power Adapter/Charger)
may cause the camcorder’s built-in memory to
become corrupt. Never remove the power
supply unit at this stage.
If you check the remaining still images on
INDEX Menu after deleting . . .
EXIT
01
<INDEX>
02
03
06
NOTES:
●Before deleting some still images stored in memory,
perform “Protect” for the necessary ones (੬ pg. 49) or
save them on a PC so that you do not lose them
accidentally (੬ pg. 45).
04
05
●Even if “ALL” is selected on the Delete Menu, it is not
possible to delete a still image with a padlock mark.
“ALL” only deletes all still images that are not protected.
After images are deleted from memory, the remaining
images are automatically moved up to fill in any gaps in
the numerical sequence. The Index No. for images
protected (with the padlock mark) may therefore change.
●When selecting the desired still image in step 5, to move
the frame from No. 7 to 6, place the highlight bar on
“EXIT” by rotating the Select Wheel upward. Rotate it
further upward to move the frame to No. 6. Perform the
same procedure for still images that follow the 13th one.
●On the Delete Select Menu, a star mark is displayed next
to a still image you shot in the FINE mode.
●If the remaining number of shots is not 30 in the FINE
mode or 60 in the STANDARD mode when “ALL” is
selected on the DELETE Menu, initialize the camcorder’s
memory (੬ pg. 59).
USING THE REMOTE CONTROL UNIT
52
EN
The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic
operations (Playback, Stop, Pause, Fast-Forward and Rewind) of your VCR.
RM-V715U (provided)
1
Installing The Batteries
The remote control uses two ”AAA (R03)” size
batteries. See “General Battery Precautions”
(੬ pg. 65).
2
1
8
Open the battery compartment cover as
illustrated.
3
4
5
6
1
2
3
9
0
!
@
3
Insert two ”AAA (R03)” size batteries in the
correct direction.
2
7
Replace the battery compartment cover.
When using the remote control, be sure to point it
at the remote sensor. The illustration shows the
approximate transmitted beam effective area for
indoor use.
Transmitted beam
effective area
The transmitted beam may not be effective or may
cause incorrect operation outdoors or when the
remote sensor is directly exposed to sunlight or
powerful lighting.
Remote sensor
Functions
Buttons
With the camcorder’s Power Switch set
to “CAMERA” (“AUTO” or “PRO.”).
With the camcorder’s Power Switch
set to “PLAY”.
1 Infrared beam
Transmits the beam signal.
transmitting window
2 ZOOM (T/W) Buttons Zoom in/out (੬ pg. 25)
Zoom in/out (੬ pg. 53)
3 PLAY Button
—
Playback start (੬ pg. 39)
4 REW Button
Retake (rewind), Quick Review
(੬ pg. 26)
Rewind, Reverse Shuttle Search,
Previous Still Image Playback
(੬ pg. 39, 44)
5 STOP Button
—
Stop (੬ pg. 39)
6 INSERT Button
—
Insert Editing (੬ pg. 54, 55)
7 REC TIME Button
Animation, Time-Lapse (੬ pg. 56)
—
ANIM. Button
8 START/STOP Button
Functions the same as the Recording Start/Stop Button on the camcorder.
9 FF Button
Retake (forward) (੬ pg. 26)
Fast-Forward, Forward Shuttle Search,
Next Still Image Playback (੬ pg. 39,
44)
0 PAUSE Button
—
—
Pause (੬ pg. 39)
Audio dubbing (੬ pg. 55)
—
! A.DUB Button
@ INT. TIME Button
Time-Lapse (੬ pg. 56)
SELF TIMER Button*
*This function is unavailable with this camcorder.
EN53
To magnify the recorded image up to 10X at any time
during playback.
Playback Zoom
Remote sensor
NOTES:
● Use the RM-V715U remote control unit to perform this
procedure.
● Make sure that the TBC mode is activated (੬ pg. 40).
Press PLAY to find the scene of interest.
1
2
Press the ZOOM Buttons (T/W) on the remote
control. Make sure the remote control is pointed at
the camcorder’s remote sensor. Pressing T zooms in.
To End Zoom . . .
ZOOM (T/W)
.... press and hold W until magnification returns to
normal. Or, press STOP and then press PLAY.
PLAY
STOP
NOTES:
● Zoom can also be used during still playback.
● Due to digital image processing, the quality of the image
may suffer.
RM-V715U
(provided)
● After zooming in on a still video image, when normal
playback is started, the zoomed-in effect is momentarily
canceled but then resumes, returning magnification to
the previously set level.
Normal playback
Press T
USING THE REMOTE CONTROL UNIT (cont.)
54
EN
Insert Editing (VIDEO)
You can record a new scene onto a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in- and out-points. The
original audio remains unchanged.
NOTE:
Use the RM-V715U remote control unit to perform this
procedure.
System Select
Switch
Set the System Select Switch to “VIDEO”, and set the
1
2
3
Power Switch to “PLAY”.
Power Switch
Play back the tape, locate the Edit-Out point and
press PAUSE.
COUNTER R/M Button
Press and hold COUNTER R/M on the camcorder for
more than 1 second to reset the tape counter, then
press again for less than 1 second so that “M”
appears.
Display
w
Insert editing
indicator
Press REW to go a little beyond the beginning of the
scene you want to replace, press PLAY to view the
recorded tape, and press PAUSE exactly at the Edit-In
point where the new scene should start.
4
5
–
:
:
M
0
1 2 3 4
Tape Counter
Press and hold INSERT, and without releasing
INSERT, press and release PAUSE. The Insert Editing
indicator appears and the Insert Editing mode is
engaged. When the scene the camcorder is aimed at
appears on the screen, go to the next step.
e
4
Audio dubbing
indicator
–
:
:
M
0
0 5 2 0
During Audio
Dubbing
Remote sensor
To begin Insert Editing, press START/STOP. When the
counter reaches “0:00:00”, editing stops automati-
cally and the camcorder enters the Insert-Pause
mode.
6
7
To end Insert Editing, press STOP.
NOTES:
● During Insert Editing, the original audio will be heard
from the speaker.
Microphone
● After step 5, Retake (੬ pg. 26) can be performed.
● The tape may stop slightly before or after the designated
end point, and noise bars may appear. Neither indicates
a defect in the unit.
● Only the video signal is recorded in the Insert Editing
mode.
START/STOP
FF
PAUSE
A.DUB
PLAY
REW
STOP
INSERT
RM-V715U
(provided)
EN55
NOTE:
Use the RM-V715U remote control unit to perform the following procedures.
Insert Editing (Insert A Still Image
From The Built-in Memory Onto A
Tape)
Audio Dubbing
You can record a new soundtrack on a prerecorded
tape (normal audio only). The sound is recorded from
the built-in microphone.
Perform steps 1, 2 and 3 of the Insert Editing
(VIDEO) procedure (੬ pg. 54) before continuing.
You can insert a still image stored in the camcorder's
built-in memory into a previously recorded tape,
replacing a section of the original recording with
minimal picture distortion at the in- and out-points.
The original audio remains unchanged.
Press REW to go a little beyond the beginning of
1
the scene onto which you want to dub the new
audio, press PLAY to view the recorded tape,
then press PAUSE at exactly the point where
dubbing should start.
Perform steps 1 through 5 in Insert Editing (VIDEO)
(੬ pg. 54) before the following procedure.
Set the System Select Switch to “D.S.C.”. Press
Press and hold A. DUB, and without releasing
A. DUB, press and release PAUSE. The Audio
Dub-Standby mode is engaged.
1
2
REW or FF to select the still image you wish to
2
3
insert.
To begin Insert Editing, press START/STOP.
When the counter reaches “0:00:00”, editing
stops automatically and the camcorder enters
the Insert-Pause mode.
To insert still images in sequential order onto
the tape . . .
... press REW or FF to move the page forward.
To begin Audio Dubbing, press PLAY. When the
counter reaches “0:00:00”, Audio Dubbing
stops automatically and the camcorder enters
the Audio Dub-Standby mode.
To end Audio Dubbing, press STOP.
4
To insert still images at random onto the
tape . . .
NOTES:
... first record the still image you selected in
step 1 onto the tape, then press START/
STOP to engage the Insert-Pause mode. To
select another still image, press REW or FF
again, then press START/STOP. Insert Editing
begins.
● Do not press FF or REW during Audio Dub-
Standby, or the edit points will not be accurate.
● If the microphone is too close to the TV, or if the
TV’s volume is too high, whistling or howling may
occur.
NOTES
To end Insert Editing, press STOP.
(for Insert Editing and Audio Dubbing):
● Insert Editing and Audio Dubbing may not work
correctly if the tape contains blank segments, or if
the recording speed was changed during the
original recording.
● To edit/dub onto a tape, make sure the Erase
Protection tab is in the position that allows
recording. If not, slide the tab. Some cassettes have
removable tabs. If the tab has been removed, cover
the hole with adhesive tape.
3
NOTES:
● The tape may stop slightly before or after the
designated end point, and noise bars may appear.
Neither indicates a defect in the unit.
● Only video signal is recorded in the Insert Editing
mode.
● Do not press STOP during Insert Editing or Audio
Dubbing, or the edit points will not be accurate.
● During Insert Editing and Audio Dubbing, when
Insert-Pause or Audio Dub-Standby is engaged, the
counter may go slightly past “0:00:00”. Recording,
however, stops at exactly 0:00:00.
USING THE REMOTE CONTROL UNIT (cont.)
56
EN
FEATURE: Animation and Time-Lapse
Interval time
indicator
PURPOSE:
The remote control lets you set/release Interval Time
1M I N
1 / 2S
and Recording Time without using the Menu Screen.
Recording time
indicator
OPERATION:
Animation
1) Set
Instead of performing steps 1 and 2 on pg. 34
(“Animation”), press REC TIME on the remote
control. Each time REC TIME is pressed, the
Recording Time indicator appears, changing in the
following order: 1/4S, 1/2S, 1S, 5S and no indication
(off).
Remote sensor
2) Release
Instead of using the Menu in step 5 on pg. 34, press
REC TIME on the remote control until the Recording
Time indicator disappears.
Time-Lapse
1) Set
Instead of performing steps 1 through 3 on pg. 35
(“Time-Lapse”), press INT. TIME and REC TIME on
the remote control. Each time INT. TIME is pressed,
the Interval Time indicator appears, changing in the
following order: 15S, 30S, 1MIN, 5MIN and no
indication (off). Each time REC TIME is pressed, the
Recording Time indicator appears, changing in the
following order: 1/4S, 1/2S, 1S, 5S and no indication
(off).
START/STOP
RM-V715U
(provided)
REC. TIME
INT. TIME
2) Release
Instead of using the Menu in step 5 on pg. 35, press
INT. TIME and REC TIME on the remote control until
the indicators disappear.
NOTE:
Also refer to pgs. 34 and 35.
TROUBLESHOOTING
If, after following the steps in the chart below, the problem still exists, please consult your JVC dealer.
EN57
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might
prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Power
Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and proceed as usual from the beginning.
SYMPTOM
POSSIBLE CAUSE(S)
POWER
No power is supplied.
● The battery pack has not been attached correctly (੬ pg. 10).
● The battery pack is not charged (੬ pg. 10).
● The power supply has not been correctly connected (੬ pg. 11).
The power suddenly goes off and does
not come back on by itself.
● The battery pack has completely discharged.
● Remove the cassette and disconnect the power source, then
after a few minutes, try turning the power back on. If it still
does not come on, consult your nearest JVC dealer.
OTHER
Some functions are not available.
● The Power Switch is set to “AUTO”.
● Certain combinations of modes or effects are not possible to use.
During recording, the indications do
not appear.
● Press DISPLAY for longer than 1 second to make the indica-
tions appear (੬ pg. 19).
Vertical white lines appear when
shooting a very bright object.
● This sometimes occurs when the contrast between the back-
ground and the object is great. It is not a defect of the camcorder.
Bright, crystal-shaped spots appear in
the LCD monitor and the viewfinder.
● Sunlight is directly entering the lens. This is not a defect of the
camcorder.
The rear of the LCD monitor is hot.
● The light used to illuminate the LCD monitor causes it to be
hot. Close the LCD monitor to turn it off or set the power
switch to “OFF”, and let the unit cool down.
Colored bright spots appear all over the
LCD monitor or the viewfinder.
● The LCD monitor and the viewfinder are made with high-
precision technology. However, black spots or bright spots of
light (red, green or blue) may appear constantly on the LCD
monitor or in the viewfinder. These spots are not recorded on
the tape. This is not due to any defect of the unit. (Effective
dots: more than 99.99 %.)
The indicators and the picture color on
the LCD monitor are not clear.
● This may occur when the surface or the edge of the LCD
monitor is pressed.
The LCD monitor, the viewfinder and
the lens have become dirty (ex.
fingerprints).
● Wipe them gently with soft cloth. Gently wipe the LCD monitor
in a semicircle because wiping strongly spreads the stain and it
won’t come out easily.
An error number (i.e. E03) appears.
● Turn the camcorder’s power off, then disconnect the power
source. After a few minutes, try turning the power on again. If
the error number still appears, consult your nearest JVC dealer.
The image is out of focus.
● The diopter needs to be adjusted (੬ pg. 17).
● The scene being shot is adversely affecting the operation of
Auto Focus (੬ pg. 37).
Even though the Lens Cover is open, the
Lens Cover Warning indicator blinks.
● The Lens Cover Warning indicator may blink when the
camcorder is used in dark areas, regardless of the position of
the Lens Cover.
TROUBLESHOOTING (cont.)
When the System Select Switch is set to “VIDEO”:
58
EN
SYMPTOM
POSSIBLE CAUSE(S)
RECORDING
Recording cannot be performed.
● Make sure the Erase Protection tab is in the position that allows
recording. If not, slide the tab. Some cassettes have removable
tabs. If the tab has been removed, cover the hole with adhesive
tape (੬ pg. 12).
● If the System Select Switch is set to “D.S.C.”, it is not possible
to record onto the tape. Change the Switch position to
“VIDEO” (੬ pg. 18).
Recording does not start.
● The camcorder Power Switch has not been set to
“CAMERA” (“AUTO“ or “PRO.”) (੬ pg. 18).
Animation or Time-Lapse is not
available.
● Before recording in the Animation mode at the very beginning
of a tape, set the camcorder to the Recording mode for about 5
seconds, so that the tape runs smoothly. Using the Fade-in
function at this point is a good way to begin an animated
program (੬ pg. 35, 56).
PLAYBACK
The tape is running, but there is no
playback picture.
● The TV has not been set to its VIDEO mode or channel.
● If A/V connection is used, the TV’s VIDEO/TV Switch has not
been set to VIDEO.
Playback cannot be performed.
● If the System Select Switch is set to “D.S.C.”, it is not possible
to play back a tape. Change the Switch position to “VIDEO”
(੬ pg. 39).
Playback picture is blurred or
interrupted.
● The video heads are dirty or worn out. Consult your nearest
JVC dealer for head cleaning or replacement.
The counter indication is blurred during
Still playback.
● This is normal.
TAPE TRANSPORT
The tape stops during fast-forward or
rewind.
● The Counter Memory Function has been activated (੬ pg. 40).
Rewinding or fast-forwarding cannot be
performed.
● The tape is already fully wound on one reel or the other.
OTHER
The picture is blurred in the Quick
Review or Retake mode.
● This is normal while recording in the EP mode. Some noise
may be present while recording in the SP mode (੬ pg. 14).
The date and time displays
disappear.
● If you remove the power source from the camcorder while the
power is on, all settings and selections are erased. Make sure to
turn the camcorder’s power off before disconnecting the power
source.
The wrong date and time are displayed/
recorded.
● If you have not performed Date/Time Setting (੬ pg. 13), the
date and time are not displayed/recorded correctly. Be sure that
Date/Time setting is carried out.
The tape will not eject.
● The battery pack is running low.
● If the LCD monitor is not open over 60 degrees, EJECT switch
does not function.
EN59
When the System Select Switch is set to “D.S.C.”:
SYMPTOM
POSSIBLE CAUSE(S)
SHOOTING
Although SNAPSHOT is pressed, a still
image is not stored in the built-in
memory.
● When the number of remaining shots available reaches “0”
(blinking), it becomes impossible to take your next shot.
Perform “DELETE” function to remove some still images
already stored in memory (੬ pg. 50).
It is not possible to shoot in sucession.
● A still image is in the process of being stored in memory for
approx. 2 seconds after SNAPSHOT is pressed. During that
time, it is impossible to take another shot. When the still image
disappears and the scene you are currently aimed at appears
on the screen, take another shot (੬ pg. 20).
PLAYBACK
Although “ALL” is selected in the
DELETE Menu Screen, all still images
cannot be deleted.
● The “Protect” function is in effect for some still images. If they
are not necessary, cancel the “Protect” function, then try
deleting all still images again (੬ pg. 49).
OTHER
Date/Time Insert is not performed
while shooting a still image.
● It is not possible to display the date/time on a still image.
● It is not possible to display the Instant Titles on a still image.
● It is not possible to set “REC TIME” in the Menu Screen.
Instant Titles are not displayed while
shooting a still image.
Some settings cannot be changed in the
Menu Screen.
Since the camcorder is a microcomputer-controlled device, external noise and interference (from a TV, a
radio, etc.) might prevent it from functioning properly. For example, when a still image you shot is stored
in the camcorder's built-in memory, the above may cause the following: Although the remaining number
of shots indicator shows that shooting is possible, a still image cannot be stored in memory after shooting.
In such a case, initialize the memory by following steps 1 through 3 below. Please note that initialization
deletes all the still images (including ones for which you performed the “Protect” function) stored in the
camcorder’s memory. If you wish to keep any of the still images that are stored in memory, before
initialization first transfer them to a PC and save them. If image data is corrupt, transfer is impossible.
1. Set the System Select Switch to “D.S.C.”, then set the Power Switch to
FORMAT
“PLAY”.
CANCEL
ENTER
2. Press COUNTER R/M for more than 2 seconds. The FORMAT Menu
appears.
3. Rotate the Select Wheel to move the highlight bar to “CANCEL” or
“ENTER”, then press it.
•“CANCEL” does not initialize the memory.
•“ENTER” initializes the memory. During initialization, “ENTER” blinks.
When initialization is complete, the screen becomes blue back.
FORMAT Menu
CAUTION:
While “ENTER” is selected and it is blinking, switching off the camcorder or removing the power supply
unit (battery pack or AC Power Adapter/Charger) may cause the camcorder’s built-in memory to become
corrupt. Never remove the power supply unit at this stage.
INDEX Controls, Connectors And Indicators
60
EN
o
W
2
1
p
w
E
R
Q
e r
t
7
9
0
8
U
!
#
@
$
&
%
^
q
3
4 5 6
T
Y
I
O
P
y u
*
( i )
EN61
Controls
Connectors
1 Diopter Adjustment Control ................. ੬ pg. 17
w DC IN Connector................................. ੬ pg. 11
2 Lens Cover Open/Close Ring................ ੬ pg. 18
The connectors e to y are located beneath the
cover.
3 Video Light Switch
[LIGHT OFF/AUTO/ON]...................... ੬ pg. 27
e Video Output Connector ...................... ੬ pg. 42
r Audio Output Connector ..................... ੬ pg. 42
t S-Video Output Connector ................... ੬ pg. 42
4 Snapshot Button [SNAPSHOT] ....... ੬ pg. 20, 23
5 •Power Zoom Lever [T/W] .................. ੬ pg. 25
•Speaker Volume Control [VOL.] ........ ੬ pg. 39
y J Terminal [JLIP (Joint Level Interface Protocol)
6 •Picture Stabilizer Button
Connector]
[P.STABILIZER] .................................. ੬ pg. 25
•Time Base Corrector Button ............... ੬ pg. 40
•It is used to connect the camcorder to a device
such as a personal computer.
For further details consult your nearest JVC
dealer.
•JLIP-controlled editing from camcorder to VCR
is not possible if the VCR is not equipped with a
J terminal.
7 Program AE Button [P.AE]..................... ੬ pg. 29
8 Fade/Wipe Button [EFFECT] ................. ੬ pg. 28
9 System Select Switch
[D.S.C./VIDEO] ................ ੬ pg. 18, 20, 39, 44
0 •Retake Rewind Button [RETAKE R]..... ੬ pg. 26
•Quick Review Button [ R] ............. ੬ pg. 26
•Rewind Button [REW] ....................... ੬ pg. 39
•Previous Page Button [PAGE–] ........... ੬ pg. 44
! •Retake Forward Button [RETAKE F] .... ੬ pg. 26
•Fast-Forward Button [FF] ................... ੬ pg. 39
•Next Page Button [PAGE+] ................ ੬ pg. 44
u Digital Connector ............................... ੬ pg. 45
Indicators
i Power Lamp ........................................ ੬ pg. 18
Other Parts
o Battery Pack Mount ............................. ੬ pg. 11
p Viewfinder ........................................... ੬ pg. 17
Q Grip Strap ............................................ ੬ pg. 17
@ Stop Button [STOP] ........................ ੬ pg. 26, 39
# Play/Pause Button
[PLAY/PAUSE] ............................... ੬ pg. 26, 39
$ •Select Wheel [PUSH] .................. ੬ pg. 30, 46
W •Camera sensor
•Bright Dial [BRIGHT] ............ ੬ pg. 18, 39, 44
Be careful not to cover this area; a sensor
necessary for shooting is built-in here.
•Remote Sensor .................................. ੬ pg. 52
% MENU/DISPLAY Button ........... ੬ pg. 19, 30, 46
^ •Recording Mode Button [SP/EP] ......... ੬ pg. 14
E Video Light .......................................... ੬ pg. 27
R Microphone......................................... ੬ pg. 54
T Eyepiece .............................................. ੬ pg. 64
Y Speaker ............................................... ੬ pg. 39
U LCD Monitor ....................................... ੬ pg. 19
I Shoulder Strap Eyelets .......................... ੬ pg. 17
O Clock Battery Slot ................................ ੬ pg. 12
P Tripod Mounting Socket ....................... ੬ pg. 17
•Counter Reset/Memory Button
[COUNTER R/M] .............................. ੬ pg. 40
•Memory Initialize Button ................... ੬ pg. 59
& EJECT Switch ....................................... ੬ pg. 12
* Recording Start/Stop Button.................. ੬ pg. 18
( Power Switch
[
, OFF, AUTO, PRO.] ... ੬ pg. 18, 20, 39, 44
) Battery Release Switch
[BATTERY RELEASE] ............................ ੬ pg. 11
q PUSH Button ....................................... ੬ pg. 12
INDEX Indications
62
EN
Indications During Recording
1
2
3 4
5
6
7
–
1 2 0M I N
REC EP
S ET
STD 3 4
I L I GHT
T4 0
8
^
&
444
T
W
9
!
+
0 2
–
0
@
#
%
*
S VHS REC.
PAUSE
M
W
B
a
1X
(
5M I N
1 / 2S
BR I GHT
CONGRATULAT I ONS
)
–––––6–––––
+
–
$
b
:
:
DEC 2 5 . 9 9
AM 1 1 4 5 1 8
1 Tape Remaining Time .......................... ੬ pg. 19
6 Tape Length Indicator .......................... ੬ pg. 14
7 Zoom Indicator Bar .............................. ੬ pg. 25
Zoom Level Indicator
Approximate Zoom Ratio
8 Recording Indicator ............................. ੬ pg. 18
! Picture Stabilizer Indicator ................... ੬ pg. 25
Blinks when a tape is about to reach its end.
2 Recording Mode Indicator (SP/EP) ........ ੬ pg. 14
3,9 Program AE Indicator ...................... ੬ pg. 29
Displayed at 3 for approx. 2 seconds when
Program AE with special effects is switched from
one mode to another by pressing P.AE., then only
the indicator remains at 9.
3,0 Fade/Wipe-Standby Indicator .......... ੬ pg. 28
Displayed at 3 for approx. 2 seconds when the
Fade/Wipe is switched from one effect to another
by pressing EFFECT, then only the indicator
remains at 0.
@ Interval Time/Recording Time
Indicator ........................................ ੬ pg. 34, 56
# Bright Level Indicator ........................... ੬ pg. 18
$ Instant Title Display ............................. ੬ pg. 33
% Date/Time Display ............................... ੬ pg. 33
^ Focus Indicator .................................... ੬ pg. 37
& Exposure Control Level Counter ........... ੬ pg. 36
* White Balance Mode Indicator............. ੬ pg. 38
( S-VHS/S-VHS ET Recording Indicator ... ੬ pg. 15
) Record–Standby Mode Indicator .......... ੬ pg. 18
4 •Picture Mode Display .................. ੬ pg. 21, 22
•Remaining Number Of Shots
Indicator ..................................... ੬ pg. 21, 22
5 Recording Format Indicator (S/S-ET) ..... ੬ pg. 15
EN63
1 •
: Cassette Indicator
Indications During Playback
Displayed when a tape is loaded.
•w: Insert Editing Indicator .................. ੬ pg. 54
Displayed during Insert Editing.
1
2 3
4
5 6
7
8
2 TBC Indicator ...................................... ੬ pg. 40
3 Playback Special Effect Indicator .......... ੬ pg. 40
4 Recording Format Indicator (S/S-ET) ..... ੬ pg. 15
5 Tape Counter ................................. ੬ pg. 40, 54
6 Recording Mode Indicator (SP/EP) ........ ੬ pg. 14
7 Tape Running Indicator
–
S ET
SP
:
4
–
:
TBC
1
2 3 4 5
AT
MONOTONE
4
: Playback
3
2
6
: Fast-Forward/Shuttle Search
: Rewind/Shuttle Search
: Pause
–
:
:
M 0 1 2 3 4
e4
: Audio Dubbing
8 Tracking Indicator ................................ ੬ pg. 40
9 Tape Counter ....................................... ੬ pg. 54
Displayed only during Insert Editing.
–––––6–––––
+
VOLUME
–
0
9
0 •BRIGHT: Bright Level Indicator .......... ੬ pg. 39
•VOLUME: Speaker Volume
Indicator ........................................... ੬ pg. 39
Warning Indications
Indications
Function
Displays the battery remaining power.
Remaining power level: high. It does not necessarily mean that the battery
pack is fully charged.
Remaining power level: exhausted
As the battery power comes close to nil, the battery indicator
(battery power warning).
blinks
When the battery power is exhausted, power turns off automatically.
Blinks when no cassette is loaded, or when the Erase Protection tab is not in
the position that allows recording.
(੬ pg. 12)
Blinks for approx. 10 seconds when the power is turned on. This display also
blinks when the clock (lithium) battery is either not installed or has discharged.
Install or replace the old battery with a new one.
(੬ pg. 12)
Appears when the tape ends during recording, playback or fast-forward.
TAPE END
(੬ pg. 19)
Blinks for approx. 5 seconds when the camcorder is turned on with the lens
LENS COVER
cover closed.
(੬ pg. 18)
These 2 warnings appear alternately every 3 seconds if condensation occurs. In this
case, all functions except tape eject and power on/off are disabled. Turn the unit off
(without removing the power supply), wait a few minutes for the warnings to clear,
and turn it on again.
CONDENSATION
PLEASE WAIT
TAPE HEAD IS DIRTY
USE CLEANING
CASSETTE
These 2 warnings appear alternately every 3 seconds if dirt is detected on the
heads during recording. In this case, use an optional cleaning cassette. If the
warning remains after cleaning, consult your nearest JVC dealer.
The error indications (E01 — E06) show what type of malfunction has occured.
If an error indication and warning appear, turn the unit off, remove the power
supply (battery, etc.) and wait a few minutes for them to clear. When it does,
you can resume using the camcorder. If the indication remains, consult your
nearest JVC dealer.
E01 — E06
SAFEGUARD FUNCTION
HAS BEEN ACTIVATED
REATTACH BATTERY
USER MAINTENANCE
64
EN
LENS COVER Open/Close Ring
After Use
Turn off the camcorder.
1
2
3
4
5
6
Open the LCD monitor fully. Slide EJECT to open the
cassette holder, then remove the cassette.
Press PUSH to close and lock the cassette holder.
Close and lock the LCD monitor.
BATTERY RELEASE
Set to “OFF”.
Slide BATTERY RELEASE to remove the battery pack.
Turn the LENS COVER Open/Close Ring to close
the lens cover.
Cleaning The Camcorder
To clean the exterior, wipe gently with a soft cloth.
Put the cloth in diluted mild soap and wring it well to
wipe off heavy dirt. Then wipe again with a dry cloth.
1
2
Remove.
EJECT Switch
Open the LCD monitor and wipe gently with a soft
cloth. Be careful not to damage the monitor. Close
the LCD monitor.
PUSH Button
To clean the lens, blow it with a blower brush, then
wipe gently with lens cleaning paper.
3
4
5
6
To detach the eyepiece, turn it counterclockwise and
pull it out.
Remove dust from the viewfinder using a blower
brush.
Re-attach the eyepiece and turn it clockwise.
NOTES:
● Avoid using strong cleaning agents such as benzine or alcohol.
● Cleaning should be done only after the battery pack has been removed or other power units have been
disconnected.
● Mold may form if the lens is left dirty.
● When using a cleaner or chemically treated cloth refer to the cautions of each product.
● When removing the eyepiece, be sure to hold the viewfinder securely.
CAUTIONS
When using the AC Power Adapter/Charger in areas
other than the USA
EN65
5. Do not expose the batteries to excessive heat as
they can leak or explode.
Ⅲ The provided AC Power Adapter/Charger features
automatic voltage selection in the AC range from
110 V to 240 V.
6. Do not dispose of the batteries in a fire.
7. Remove the batteries from the unit if it is to be
stored for an extended period to avoid battery
leakage which can cause malfunctions.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to an AC
wall outlet other than American National Standard
C73 series type use an AC plug adapter, called a
“Siemens Plug”, as shown.
Battery Packs
The battery packs are nickel-cadmium
or nickel metal-hydride batteries.
Before using the supplied battery pack
or an optional battery pack, be sure to
read the following cautions:
For this AC plug adapter, consult your nearest JVC
dealer.
Plug adapter
1.To avoid hazard . . .
... do not burn.
Terminals
... do not short-circuit the terminals.
... do not modify or disassemble.
... use only specified chargers.
Video Light
DANGER:
•The video light becomes extremely hot. Do not
touch it either while in operation or soon after
turning it off, otherwise serious injury may result.
•Do not place the camcorder into the carrying case
immediately after using the video light, since it
remains extremely hot for some time.
•When operating, keep a distance of about 30 cm
(11-13/16" ft.) between the video light and people
or object.
•Do not use near flammable or explosive materials.
•It is recommended that you consult your nearest
JVC dealer for replacing the video light.
2.To prevent damage and prolong service
life . . .
... do not subject to unnecessary shock.
... avoid repeated charging without fully discharg-
ing.
... charge in an environment where temperatures
are within the tolerances shown in the chart
below. This is a chemical reaction type
battery—cooler temperatures impede chemical
reaction, while warmer temperatures can
prevent complete charging.
... store in a cool, dry place. Extended exposure to
high temperatures will increase natural
discharge and shorten service life.
... avoid prolonged uncharged storage.
... remove from charger or powered unit when
not in use, as some machines use current even
when switched off.
General Battery Precautions
If the remote control or cassette adapter is not
functioning even if it is being operated correctly, the
batteries are exhausted. Replace them with fresh
ones.
NOTES:
●It is normal for the battery pack to be warm after
charging, or after use.
Use only the following batteries:
Temperature Range Specifications
Charging .............. 10°C to 35°C (50°F to 95°F)
Operation ............ 0°C to 40°C (32°F to 104°F)
Storage ................ –10°C to 30°C (14°F to 86°F)
●Recharging time is based on room temperature of
20°C (68°F.)
Remote control ................. AAA (R03) size x 2
(RM-V715U)
Cassette adapter ............... AA (R6) size x 1
(C-P6U or C-P7U)
Please make note of the following rules for battery
use. When misused, the batteries can leak or
explode.
●The lower the temperature, the longer recharging
takes.
1. When replacing batteries, refer to page 52 for the
remote control, or read the cassette adapter
(C-P6U/C-P7U) instructions.
2. Do not use any different size of batteries from
those specified.
3. Be sure to install batteries in the correct direction.
4. Do not use rechargeable batteries.
CAUTIONS (cont.)
66
EN
Cassettes
Main Unit
To properly use and store your cassettes, be sure to
read the following cautions:
1.For safety, DO NOT . . .
... open the camcorder’s chassis.
... disassemble or modify the unit.
... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use.
1.During use . . .
... make sure the cassette bears the VHS-C mark.
... be aware that recording onto prerecorded tapes
automatically erases the previously recorded
video and audio signals.
... allow inflammables, water or metallic objects
to enter the unit.
... remove the battery pack or disconnect the
power supply while the power is on.
... leave the battery pack attached when the
camcorder is not in use.
... make sure the cassette is positioned properly
when inserting.
... do not load and unload the cassette
repeatedly without allowing the tape to run at
all. This slackens the tape and can result in
damage.
2.Avoid using the unit . . .
... in places subject to excessive humidity or dust.
... in places subject to soot or steam such as near
a cooking stove.
... do not open the front tape cover. This exposes
the tape to fingerprints and dust.
2.Store cassettes . . .
... in places subject to excessive shock or
vibration.
... near a television set.
... near appliances generating strong magnetic or
electric fields (speakers, broadcasting antennas,
etc.).
... in places subject to extremely high (over 40°C
or 104°F) or extremely low (under 0°C or 32°F)
temperatures.
... away from heaters or other heat sources.
... out of direct sunlight.
... where they won’t be subject to unnecessary
shock or vibration.
... where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
... vertically, in their original cases.
3.DO NOT leave the unit . . .
... in places of over 50°C (122°F).
... in places where humidity is extremely low.
(below 35%) or extremely high (above 80%).
... in direct sunlight.
... in a closed car in summer.
... near a heater.
4.To protect the unit, DO NOT . . .
... allow it to become wet.
... drop the unit or strike it against hard objects.
... subject it to shock or excessive vibration during
transportation.
... keep the lens directed at extremely bright
objects for long periods.
... direct the eyepiece of the viewfinder at the sun.
... carry it by holding the viewfinder or the LCD
monitor. Be sure to hold the main unit with
both hands or use the grip.
... swing it excessively when using the shoulder
strap.
EN67
Declaration of Conformity
LCD Monitor
Model Number
Trade Name
Responsible party
Address
: GR-SXM920U
: JVC
1.To prevent damage to the LCD monitor, DO
NOT . . .
: JVC AMERICAS CORP.
: 1700 Valley Road
Wayne, N.J. 07470
: (973) 315–5000
... push it strongly or apply any shocks.
... place the camcorder with the LCD monitor on
the bottom.
Telephone Number
2.To prolong service life . . .
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
... avoid rubbing it with coarse cloth.
3.Be aware of the following phenomena for
LCD monitor use. These are not malfunc-
tions:
•While using the camcorder, the surface around the
LCD monitor and/or the back of the LCD monitor
may heat up.
•If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
Change or modifications not approved by the
party responsible for compliance could void the
user’s authority to operate the equipment. This
equipment has been tested and found to comply
with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment gener-
ates, uses, and can radiate radio frequency
energy and, if not installed and used in accord-
ance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equip-
ment does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equip-
ment and receiver.
How To Handle a CD-ROM
•Take care not to soil or scratch the mirror surface
(opposite to the printed surface). Do not write
anything or put a sticker on either the front or back
surface. If the CD-ROM gets dirty, gently wipe it
with a soft cloth outward from the center hole using
a circular motion.
•Do not use conventional disc cleaners or cleaning
spray.
•Do not bend the CD-ROM or touch its mirror
surface.
•Do not store your CD-ROM in a dusty, hot or
humid environment. Keep it away from direct
sunlight.
About moisture condensation . . .
● You may have observed that pouring a cold
liquid into a glass will cause drops of water to
form on the glass’ outer surface. This same
phenomenon occurs on the head drum of a
camcorder when it is moved from a cool place
to a warm place, after heating a cold room,
under extremely humid conditions or in a
place directly subjected to the cool air from an
air conditioner.
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
technician for help.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.
TERMS
68
EN
A
F
AC Power Adapter/Charger ......................pg. 10, 11
Animation Recording .............................. pg. 34, 56
Audio Dubbing ............................................. pg. 55
Auto Date Record ......................................... pg. 33
Auto Focus.................................................... pg. 37
Auto Shut Off .......................................... pg. 19, 39
Fade-In/Out .................................................. pg. 28
Fast-Forward Tape ......................................... pg. 39
FINE Mode.................................................... pg. 22
Fine Still........................................................ pg. 39
Full Image ............................................... pg. 21, 24
G
B
Grip Adjustment............................................ pg. 17
Battery Pack ...................................... pg. 10, 11, 65
Brighten The Image ....................................... pg. 36
Brighten The LCD Monitor ............................ pg. 18
H
High Speed Shutter Mode ............................. pg. 29
I
C
INDEX Menu ................................................ pg. 48
Index Mode .................................................. pg. 48
Index Number............................................... pg. 48
Initialization.................................................. pg. 59
Insert Editing ........................................... pg. 54, 55
Instant Delete................................................ pg. 26
Instant Titles .................................................. pg. 33
Interface Shooting ......................................... pg. 19
Car Battery .................................................... pg. 11
Cassette Adapter ........................................... pg. 41
Charge Marker .............................................. pg. 10
Charging The Battery Pack ............................ pg. 10
Classic Film Effect ......................................... pg. 40
Clean The Camcorder ................................... pg. 64
Clock (Lithium) Battery ................................. pg. 12
COM Port (RS-232C)..................................... pg. 45
Connection To A VCR/TV ............................. pg. 42
Connection To A Windows PC/Macintosh ..... pg. 45
Contents ................................................ cover page
Counter Memory ........................................... pg. 40
J
JLIP ID NO. ................................................... pg. 32
Journalistic Shooting ..................................... pg. 19
JPEG ............................................................. pg. 22
D
L
Darken The Image ........................................ pg. 36
Darken The LCD Monitor ............................. pg. 18
Date/Time Display ........................................ pg. 33
Date/Time Settings ........................................ pg. 13
DELETE Menu ............................................... pg. 50
Delete Mode ................................................. pg. 50
Delete Select Menu....................................... pg. 50
Demonstration Mode ................................ pg. 8, 32
Digital Zoom ................................................ pg. 31
Digital Still Camera ............................... pg. 20 – 22
Diopter Adjustment ....................................... pg. 17
LCD monitor/Viewfinder, Indications ...... pg. 62, 63
Load A Tape .................................................. pg. 12
M
Manual Focus ............................................... pg. 37
Menu Screen......................................... pg. 30 – 32
Modem Port .................................................. pg. 45
Monotone Effect ............................................ pg. 40
Move The Page Back .................................... pg. 44
Move The Page Next..................................... pg. 44
N
E
ND Effect Mode ............................................ pg. 29
Nega/Posi Mode ........................................... pg. 29
Electronic Fog Filter Mode ............................ pg. 29
Erase Protection ............................................ pg. 12
Exposure Control .......................................... pg. 36
EN69
P
T
Padlock Mark ................................................ pg. 49
Picture Mode Setting ..................................... pg. 22
Picture Stabilizer ........................................... pg. 25
Pin-Up Image .......................................... pg. 21, 24
Playback (D.S.C.) .......................................... pg. 44
Playback (VIDEO) ......................................... pg. 39
Playback Special Effects ................................ pg. 40
Playback Zoom ............................................. pg. 53
Power Switch Position .................................. pg. 18
Printer Port.................................................... pg. 45
Program AE With Special Effects ................... pg. 29
PROTECT Menu............................................ pg. 49
Protect Mode ................................................ pg. 49
Provided Accessories ...................................... pg. 9
Tape Counter .......................................... pg. 40, 54
Tape Dubbing ......................................... pg. 42, 43
Tape Length Setting ....................................... pg. 14
Tele Macro .................................................... pg. 31
Time Base Corrector ..................................... pg. 40
Time-Lapse Shooting ............................... pg. 35, 56
Tracking ........................................................ pg. 40
Tripod Mounting ........................................... pg. 17
Twilight Mode ............................................... pg. 29
U
Unload A Tape .............................................. pg. 12
V
Video Echo Effect .......................................... pg. 40
Video Light ................................................... pg. 27
Viewfinder Adjustment .................................. pg. 17
Q
Quick Review ............................................... pg. 26
W
R
White Balance Adjustment ............................ pg. 38
Wide Mode ................................................... pg. 31
Wipe-In/Out.................................................. pg. 28
Recording, Advanced Features (VIDEO) pg. 28 – 38
Recording, Start/Stop (VIDEO) ................. pg. 18, 19
Recording Format ......................................... pg. 15
Recording Mode ........................................... pg. 14
Record-Standby ............................................ pg. 18
Remote Control............................................. pg. 52
Retake ........................................................... pg. 26
Rewind The Tape .......................................... pg. 39
Z
Zooming ....................................................... pg. 25
S
Self-Recording .............................................. pg. 19
Sepia Mode ................................................... pg. 29
Shooting, Advanced Features
(D.S.C.)............................pg. 29 – 32, 34, 36 – 38
Shooting (D.S.C.) .................................. pg. 20 – 22
Shoulder Strap Attachment ............................ pg. 17
Shuttle Search ............................................... pg. 39
Slide Show Mode .......................................... pg. 47
Snapshot During Playback ............................ pg. 24
Snapshot Mode ....................................... pg. 20, 23
Snapshot (VIDEO) ................................... pg. 23, 24
Specifications ................................................ pg. 70
Sports Mode .................................................. pg. 29
STANDARD Mode ........................................ pg. 22
Star Mark On The Setting Menus ....... pg. 48, 49, 51
Still Image Data Transfer ............................... pg. 45
Still Playback ................................................ pg. 39
Store A Still Image In The Built-In Memory .... pg. 20
Strobe Effect .................................................. pg. 40
Super LoLux (S.LX) ........................................ pg. 31
Super VHS Expansion Technology................. pg. 15
SPECIFICATIONS
: Electronic viewfinder with
0.55" color LCD
70
EN
Viewfinder
Camcorder
White balance
adjustment
LCD monitor
General
Format
Power source
Power consumption
LCD monitor off,
viewfinder on
LCD monitor on,
viewfinder off
LCD monitor on,
viewfinder on
Video light
: Auto/Manual adjustment
: 3" diagonally measured, LCD
panel/TFT active matrix
system
: VHS NTSC standard
: DC 6.0 V
Speaker
: Monaural
: 4.7 W
: 5.2 W
Connectors
JLIP
: ø3.5 mm, 4-pole, mini-head
jack (compatible with
RC-5325 plug)
: 1 Vp-p, 75 Ω unbalanced,
analog output
(via Video output connector)
: –8 dBs, 1 kΩ analog output
(via Audio output connector)
: ø2.5 mm, 4-pole, mini-head
jack
: 5.7 W
: 3.0 W
: NTSC-type
Video
Signal system
Video recording system
Luminance
Color
: FM recording
: Converted sub-carrier
direct recording
Audio
Digital
S-Video
Conforms to VHS standard
Cassette
Tape speed
SP
EP
:
/
cassette
: Y : 1Vp-p, 75 Ω, analog
output
: 33.35 mm/sec. (1-5/16 ips)
: 11.12 mm/sec. (7/16 ips)
C : 0.29 Vp-p, 75 Ω, analog
output
Recording time (max.)
SP
EP
: 40 minutes
: 120 minutes (with TC-40)
AC Power Adapter/Charger AA-V16U
Power requirement
U.S.A. and Canada : AC 120 V`, 60 Hz
D.S.C. format
Recording format : Digital data storage
(based on JPEG)
Recording medium : Built-in flash memory,
2 Mbyte
Number of storable
Other countries
: AC 110 V to 240 V`,
50/60 Hz
Power consumption : 23 W
Output
Charge
: DC 8.5 V
: DC 6.3 V
, 1.3 A
, 1.8 A
shots
: FINE mode:
VTR
approx. 30 shots
STANDARD mode:
approx. 60 shots
: 640 x 480 pixels
(when captured on a PC)
Charging system
: Constant current, peak
detection, timer controlled
: 125 (W) x 42 (H) x 68 (D) mm
(4-15/16" x 1-11/16" x
2-11/16")
Dimensions
Weight
Image size
Operating
temperature
: Approx. 270 g (0.6 lbs)
: 0°C to 40°C (32°F to 104°F)
Operating humidity : 35% to 80%
Storage temperature : –20°C to 50°C
(–4°F to 122°F)
Cassette Adapter C-P7U
Dimensions
: 188 (W) x 25 (H) x
104 (D) mm
(7-7/16" x 1" x 4-1/8")
: Approx. 240 g (0.53 lbs)
: “AA (R6)”-size battery x 1
Weight
: Approx. 870 g (2.0 lbs)
Dimensions
: 198 (W) x 119 (H) x
99 (D) mm (7-13/16" x 4-11/
16" x 3-15/16") (with the LCD
monitor closed and with the
viewfinder fully tilted
Weight
Accessory
downward)
Specifications shown are for SP mode unless
otherwise indicated. E & O.E. Design and specifica-
tions subject to change without notice.
Pickup
Lens
: 1/4" format CCD
: F1.6, f = 3.9 to 62.4 mm,
16:1 power zoom lens with
auto iris and macro control,
filter diameter 40.5 mm
ESPAÑOL
EN71
Batería BN-V12U o BN-V20U
Alimentación
Marcas
Esta cámara de video posee un sistema de alimentación de 3
vías que le permite seleccionar la fuente de alimentación más
apropiada. No utilice las unidades de alimentación
suministradas con otro equipo.
A la toma de
corriente de CA
Indicador
CHARGE (carga)
CARGA DE LA BATERIA
Asegúrese de desconectar el cable CC de la cámara de
video del adaptador/cargador de CA. Conecte el cable
de alimentación de CA del cargador a una toma de
corriente.
1
Adaptador/
Cargador de CA
AA-V16U
Alinee las marcas y deslice la batería en la dirección de
la flecha hasta que quede bloqueada en su lugar.
2
El indicador CHARGE comienza a destellar para indicar
que se ha iniciado la carga.
Conector DC OUT
Batería
BN-V11U
Tiempo de carga
aprox. 1 h 10 min
aprox. 1 h 10 min
aprox. 1 h 50 min
Cuando el indicador CHARGE deja de destellar y
permanece encendido, la carga ha terminado. Deslice la
3
batería en el sentido opuesto al de la flecha y retírela.
Recuerde de desconectar el cable de alimentación del
adaptador/cargador de CA de la toma de corriente alterna.
BN-V12U (opcional)
BN-V20U (opcional)
ATENCION:
La carga de la batería sin que esté completamente agotada afectará a la capacidad original de ésta. Efectué el
procedimiento abajo para descargar totalmente la batería antes de recargarla.
1. Coloque la batería en la cámara de video y asegúrese que el cassette esté no colocado, luego ajuste el
conmutador de alimentación en ”AUTO” o ”PRO.”.
2. La alimentación de la camára de video se desconectará automáticamente cuando la descarga termina.
Cuando usted no vaya a usar una batería por un período prolongado, asegúrese de descargarla totalmente antes
de almacenarla porque dejar la batería sin que esté completamente agotada afectará su rendimiento.
USO DE LA BATERIA
Enganche el extremo a la cámara de video
y presione la
batería hasta que se trabe en el lugar
.
•
Si la batería es colocada en la posición equivocada puede
ocurrir un mal funcionamiento.
Para la extracción de la batería . . .
..... deslice BATTERY RELEASE y extraiga la batería.
A
B
Tiempo de grabación aproximado
Enganche.
Empuje.
BATTERY RELEASE
Monitor LCD
desconectado/ conectado/visor conectado/
visor conectado desconectado visor conectado
Monitor LCD
Monitor LCD
Batería
ATENCION:
BN-V11U
1 h 20 min
(45 min)
1 h 10 min
(40 min)
1 h 5 min
(40 min)
Antes de desmontar la fuente de alimentación,
asegúrese que la alimentación de la cámara
de video esté desconectada. El no hacerlo
puede producir un error de funcionamiento
en la cámara de video.
BN-V12U
(opcional)
1 h 20 min
(45 min)
1 h 10 min
(40 min)
1 h 5 min
(40 min)
BN-V20U
(opcional)
2 h 10 min
(1 h 15 min)
1 h 55 min
(1 h 10 min)
1 h 45 min
(1 h 5 min)
BN-V856U 8 h 30 min
(opcional) (5 h 10 min)
7 h 40 min
(4 h 50 min)
7 h
(4 h 30 min)
Indicador de carga*
*Se incorpora un indicador
de carga sobre la batería
para ayudarle a recordar si
ha sido cargada o no. Los
dos colores indicadores
(rojo y negro), le permiten
seleccionar la carga y la
descarga.
(
) : Cuando está encendido el foco.
INFORMACION:
El VU-V856KIT es un juego compuesto de la batería
BN-V856U y del cargador/adaptador de CA AA-V80U. Lea los
manuales de instrucción del VU-V856KITU antes de utilizarlo.
Es imposible cargar la batería BN-V856U utilizando el
cargador/adaptador de CA suministrado. Use el cargador/
adaptador de CA AA-V80U opcional.
GUIA PARA OPERACION RAPIDA (VIDEO)
72
EN
Si la unidad comienza a funcionar mal, deje de usarla inmediatamente y consulte a su concesionario local de JVC.
ALIMENTACION
INSERCION DEL CASSETTE DE
VIDEO
A Enganche.
B Empuje.
Botón PUSH Conmutador EJECT
BATTERY RELEASE
Utilización de la batería
Enganche el lado extremo de la batería en la
cámara de video y empuje la batería hasta
que se bloquee en el lugar
1 Abra el monitor LCD completamente.
2 Deslice EJECT para abrir el portacassette.
3 Inserte cassette de video.
4 Presione PUSH para cerrar el portacassette.
(Por más detalles, ੬ p. 12)
.
(Procedimiento para carga, ੬ p. 10)
Para extraer la batería
Deslice BATTERY RELEASE y extraiga la batería.
REPRODUCCION
FILMACION
Botón de
rebobinado (2
3
1
)
Anillo de abertura
del cubreobjetivo
(LENS COVER)
3
Colóquelo en
“AUTO” o “PRO.”.
Botón de
4
reproducción/pausa
Colóquelo
en “PLAY”.
2
Botón de inicio/parada de grabación
4
(4/6)
Colóquelo en
“VIDEO”.
Botón de parada (5)
Colóquelo en “VIDEO”.
1
2
1 Ajuste el conmutador selector de sistema en
“VIDEO”.
1 Gire el anillo LENS COVER de abertura/cierre
para abrir el cubreobjetivo.
2 Ajuste el conmutador de alimentación en “PLAY”.
2 Ajuste el conmutador selector de sistema en
3 Presione
2.
“VIDEO”.
— La cinta se detiene automáticamente al
comienzo de la misma.
3 Adjuste el conmutador de alimentación en
“AUTO” o “PRO.”.
4 Presione 4/6.
— La lámpara de alimentación se encenderá y
aparecerá una imagen.
— Comienza la reproducción y la imagen aparece.
• Presione 5 para detener la grabación.
(Por más detalles, ੬ p. 39.)
• El visor se desconecta automáticamente para ahorrar
energía cuando el monitor LCD es abierto a un
ángulo mayor de 60 grados.
• El monitor LCD se activa/desactiva cuando se lo
abre/cierre a 60 grados aprox.
4 Presione el botón inicio/parada de grabación.
— Comenzará la grabación.
• Para detener temporariamente la grabación, presione
nuevamente el botón de inicio/parada de grabación.
(Por más detalles, ੬ p. 18, 19)
• El visor se desconecta automáticamente para ahorrar
energía cuando el monitor LCD es abierto a un
ángulo mayor de 60 grados.
• El monitor LCD se activa/desactiva cuando se lo
abre/cierre a 60 grados aprox.
O simplemente reproduzca la cinta en un VCR de
VHS utilizando el adaptador de cassette (VHS
Playpak). ੬ p. 41
GUIA PARA OPERACION RAPIDA (D.S.C.)
EN73
Si la unidad comienza a funcionar mal, deje de usarla inmediatamente y consulte a su concesionario local de JVC.
FILMACION
ALIMENTACION
A Enganche.
Botón SNAPSHOT
4
B
Empuje.
Anillo de abertura
del cubreobjetivo
(LENS COVER)
1
Colóquelo en
“AUTO” o “PRO.”.
3
BATTERY RELEASE
Colóquelo en “D.S.C.”.
2
Utilización de la batería
Enganche el lado extremo de la batería en la
cámara de video y empuje la batería hasta
que se bloquee en el lugar
1 Gire el anillo LENS COVER de abertura/
cierre para abrir el cubreobjetivo.
2 Ajuste el conmutador selector de sistma en
“D.S.C.”.
3 Ajuste el conmutador de alimentación en
“AUTO” o “PRO.”.
.
(Procedimiento para carga, ੬ p. 10)
Para extraer la batería
Deslice BATTERY RELEASE y extraiga la batería.
— La lámpara de alimentación se encenderá
y aparecerá una imagen.
4 Presione el botón SNAPSHOT.
— Una imagen fija es filmada y almacenada
en la memoria de la cámara de video.
(Por más detalles,੬ p. 20 a 22)
REPRODUCCION
3 (Botones de página siguiente/anterior
2/PAGE – o 3/PAGE +)
•El visor se desconecta automáticamente para
ahorrar energía cuando el monitor LCD es
abierto a un ángulo mayor de 60 grados.
•El monitor LCD se activa/desactiva cuando se
lo abre/cierre a 60 grados aprox.
2
Colóquelo
en “PLAY”.
Colóquelo en “D.S.C.”.
1
1 Ajuste el conmutador selector de sistema en
“D.S.C.”.
2 Ajuste el conmutador de alimentación en “PLAY”.
— Aparece una imagen fija almacenada en la
memoria.
3 Presione 2/PAGE – o 3/PAGE + para
seleccionar la imagen fija que desea ver.
(Por más detalles, ੬ p. 44.)
•El visor se desconecta automáticamente para
ahorrar energía cuando el monitor LCD es
abierto a un ángulo mayor de 60 grados.
•El monitor LCD se activa/desactiva cuando se
lo abre/cierre a 60 grados aprox.
FOR SERVICING (Only in U.S.A.)
74
EN
HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE: 1-800-252-5722
Dear customer:
In order to receive the most satisfaction from your purchase, read the instruction booklet before
operating the unit. In the event that repair is necessary, or for the address nearest your location,
please refer to the factory service center list below or within the Continental United States, call 1-800-
252-5722 for your authorized servicer. Remember to retain your Bill of Sale for Warranty Service.
— JVC
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
FACTORY SERVICE CENTER LOCATIONS
10 New Maple Avenue
Pine Brook, NJ 07058-9641
(973) 396-1000
1500 Lakes Parkway
Lawrenceville, GA 30243-5857
(770) 339-2522
705 Enterprise Street
Aurora, IL 60504-8135
(630) 851-7855
5665 Corporate Avenue
Cypress, CA 90630-4727
(714) 229-8011
10700 Hammerly Blvd., Suite 110 2969 Mapunapuna Place, Suite 105
Houston, TX 77043-2310
(713) 935-9331
Honolulu, HI 96819-2000
(808) 833-5828
13 Cummings Park
Woburn, MA 01801
(781) 376-9100
8192 West State Road 84
Davie, FL 33324-4611
(954) 472-1960
890 Dubuque Avenue
South San Francisco, CA 94080-1804
(650) 871-2666
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the
engineering and production of the wide array of JVC products, service is the key to maintaining the
high level performance for which JVC is world famous. The JVC service and engineering organization
stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
10 New Maple Avenue
Pine Brook, NJ 07058-9641
If you ship the product...
Pack your JVC unit in the original carton or one of equivalent size and strength. Enclose, with the unit,
a letter stating the problem or symptom that exists and also a copy of the receipt or bill of sale you
received when you purchased your JVC unit. Print your home return address on the outside and the
inside of the carton. Send to the appropriate JVC Factory Service Center as listed above.
Don’t service it yourself.
ACCESSORIES
To purchase accessories for your JVC product, you
may contact your local JVC Dealer.
Or from the 48 Continental United States call toll free:
1-800-882-2345.
CAUTION
To prevent electrical shock, do not open the
cabinet. No user serviceable parts inside.
Refer servicing to qualified service personnel.
WARRANTY (Only in U.S.A.)
EN75
LIMITED WARRANTY
CONSUMER VIDEO 1-90
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO
THE ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP
from the date of original retail purchase for the period as shown below. (“The Warranty Period”)
PARTS
LABOR
1
YR
90
DAYS
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF
COLUMBIA AND IN THE COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner.
Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized
service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All
products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for
Television sets having a screen size 25 inches and above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC
authorized service center, please call toll free: (800) 252-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with
a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center,
the name and location of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse,
faulty installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility
authorized by JVC to render such service, or if affixed to any attachment not provided with the products, or if
the model or serial number has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of
purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);from the date
of purchase);
There are no other express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY
OTHER DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT
LIMITATION, DAMAGE TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT,
OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE
LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an
implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, N.J. 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR
DETAILS OF REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT
WARRANTY INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain
this information for future reference.
Model No.:
Serial No:
Purchase date:
Name of dealer:
EN
VICTOR COMPANY OF JAPAN, LIMITED
1P2ri9n9teMdKinV*JaUpNan*YP
U
COPYRIGHT© 2000 VICTOR COMPANY OF JAPAN, LTD.
|