DIE CAST BLENDER
Model Number: 169106
UPC: 681131691062
Customer Assistance
1 877 207 0923 (US)
1 877 556 0973 (Canada)
Thank you for purchasing a GE small appliance.
In keeping with the GE ecomagination initiative, please consider the option to recycle
the packaging material and donate the appliance you are no longer using.
To read about GE’s ecomagination commitment, visit
If the power-supply cord is a grounding-type-3-wire cord with a grounding prong on the plug,
the extension cord should also be a grounding-type-3-wire cord.
GROUNDING INSTRUCTIONS
This appliance must be grounded while in use to protect the operator from electrical shock.
The appliance is equipped with a 3-conductor cord and a 3-prong grounding-type plug to fit
the proper grounding-type receptacle. The appliance has a plug that looks like Figure A. An
adaptor, as shown in Figure B, should be used for connecting a 3-prong grounding plug to a
2-ground receptacle. The grounding tab, which extends from the adaptor, must be
connected to a permanent ground such as a properly grounded outlet box as shown in
Figure C, using a metal screw.
LINE CORD SAFETY TIPS
1. Never pull or yank on cord or the appliance.
2. To insert plug, grasp it firmly and guide it into outlet.
3. To disconnect appliance, grasp plug and remove it from outlet.
4. Before each use, inspect the line cord for cuts and/or abrasion marks. If any are found,
this indicates that the appliance should be serviced and the line cord replaced.
5. Never wrap the cord tightly around the appliance, as this could place undo stress on
the cord where it enters the appliance and cause it to fray and break.
3
PARTS
7.
6.
16.
15.
14.
13.
5.
11.
4.
3.
10.
9.
12.
2.
1.
On control panel
Exploded view of glass jar
12. Glass blending jar
13. Jar collar
14. Silicone sealing ring
15. Blade assembly
16. Black locking ring
1. Die cast base
2. Control panel (see detail)
3. Jar collar
4. Blade assembly
5. Glass blending jar
6. Jar lid
9. Speed selector (0-3 and crush)
10. Power indicator light
11. Pulse button
7. Measuring cap
8. Cord storage (bottom of base)
4
OPERATING INSTRUCTIONS
Blending
1
2
3
4
5
Cleaning and Storage
6
7
8
10
11
9
5
INSTRUCTIONS FOR USE
For your safety, always read and understand this Instruction Manual before attempting to
use any electric appliance.
Before Using:
1. Carefully unpack the blender. Remove all packaging materials.
2. Wash the lid, measuring cap, blade assembly, and glass jar in hot soapy water. Dry
thoroughly.
3. Wipe exterior surfaces of the base with a soft, moist cloth to remove residue that may
have collected during packing and handling. Dry thoroughly. Do not use abrasive
cleaners. NEVER IMMERSE THE BLENDER, CORD OR PLUG IN WATER OR ANY OTHER
LIQUID.
4. Be sure all parts are properly assembled and in place before use.
Blade Assembly:
Note: Before blending, be sure the black locking ring is tightened to prevent leakage.
1. Line up the two round indentions on the metal jar collar with the two round bumps on
the glass blending jar (see figure 8).
2. Place the silicone sealing ring on the bottom of the glass jar.
3. Angle the blade assembly so one of the taller blades goes into the glass jar (see figure
9). Slowly lower the blade assembly so that the other blades enter the glass jar and
the blade assembly sits flat on top of the silicone sealing ring.
4. Replace the black locking ring around the blade assembly and rotate the black
locking ring clockwise until it is tightened (see figure 10).
Note: If you notice liquid leaking at the bottom of the glass blending jar, remove the black
locking ring and re-tighten it.
Blending:
1. Before starting, make sure the blender is in the off position. The off position is when
the blue indicator dot on the speed selector knob aligns with the “0” marking.
2. Add ingredients to the blending jar (see figure 1).
3. Place lid on blending jar (see figure 2). Make sure the metal jar collar is properly
seated on the die cast base.
4. Plug the power cord into a wall outlet. The blue power indicator light in the middle of
the speed selector knob will illuminate, indicating the blender is ready for operation.
Note: The blue indicator light will remain illuminated until the appliance is
unplugged from the wall outlet.
5. Rotate the speed selector knob clockwise to select speeds 1 (low), 2 (medium), or 3
(high) (see figure 3). Rotate the speed selector knob counter-clockwise to select the
crush setting (see figure 4).
Crush Setting: use this setting for ice crushing and chopping. The crush setting
operates intermittently so the blender crushes at full power for about 3 seconds and
then stops briefly before crushing at full power for another 3 seconds. The crush
function will continue until the speed selector knob is returned to the “0” position.
This operation allows the larger chunks of ice or other contents to settle back into the
blade area for maximum blending performance.
6
Pulse Button: use this button to blend with a pulsing action. You can blend
continuously by holding down the pulse button (see figure 5), or press and release the
pulse button for multiple short bursts.
6. To stop blending, rotate the speed selector knob so the blue indicator dot is lined up
with the off position “0”.
7. Be sure the blender is in the off “0” position when not blending.
CLEANING AND STORAGE
This appliance requires little maintenance. It contains no user-serviceable parts. Do not
attempt to repair it yourself. Any servicing that requires disassembly, other than cleaning,
must be performed by a qualified appliance repair technician.
To Clean:
1.
Before cleaning, be sure the speed control dial is in the “Off” position and the cord is
unplugged from the outlet.
2.
To make cleaning easier, rinse the center measuring cap and jar lid immediately after
use. Do not immerse the base in water or any liquid. If washing the jar by hand,
wash in hot, soapy water. Rinse and dry thoroughly. If necessary, use a nylon bristle
brush to clean the glass jar.
3.
4.
5.
Do not use scouring pads or harsh chemicals on any plastic or metal parts.
Do not fill the jar with boiling water. Do not place any parts in boiling water.
Do not allow the blade assembly to soak in water for long periods of time.
To Disassemble the Blade Assembly For Cleaning:
1.
2.
Remove the glass blending jar from the die cast base and turn it over.
Rotate the black locking ring counter-clockwise until you are able to remove it (see
figure 6).
3.
Carefully remove the blade assembly by lifting upward. Tilt the blade assembly to
angle the blade out of the glass blending jar (see figure 7).
Remove the silicone sealing ring.
4.
5.
Lift the cast metal jar collar off the glass blending jar.
The glass jar is dishwasher safe. It is recommended to clean all other parts of the blade
assembly by hand with warm, soapy water and dry with a towel or allow to air dry. Use
caution when washing and cleaning the blade assembly as the blades are sharp.
To Store:
Be sure all parts are clean and dry before storing. Store appliance in its box or in a clean, dry
place. Never wrap cord tightly around the appliance; keep it loosely coiled or use the cord
storage on the bottom of the blender (see figure 11).
7
8
|