BL01600-200
EN
DIGITAL CAMERA
Before You Begin
First Steps
X10
Owner’s Manual
Thank you for your purchase of this
product. This manual describes how
to use your FUJIFILM digital camera and
the supplied software. Be sure that you
have read and understood its contents
and the warnings in “For Your Safety”
(Pii) before using the camera.
Basic Photography and Playback
More on Photography
More on Playback
Movies
Connections
For information on related products, visit our website at
http://www.fujifilm.com/products/digital_cameras/index.html
Menus
Technical Notes
Troubleshooting
Appendix
For Your Safety
Power Lines: An outside antenna sys-
tem should not be located in the
vicinity of overhead power lines or
other electric light or power circuits,
or where it can fall into such power
lines or circuits. When installing an
outside antenna system, extreme
care should be taken to keep from
touching such power lines or circuits
as contact with them might be fatal.
Replacement Parts: When replace-
ment parts are required, be sure
the service technician has used
replacement parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock or other
hazards.
Use
Service
Cleaning: Unplug this video product Servicing: Do not attempt to service
from the wall outlet before clean- this video product yourself as open-
ing. Do not use liquid cleaners or ing or removing covers may expose
aerosol cleaners. Use a damp cloth you to dangerous voltage or other
for cleaning.
hazards. Refer all servicing to quali-
fied service personnel.
Object and Liquid Entry: Never push
objects of any kind into this video Damage Requiring Service: Unplug this
product through openings as they video product from the wall outlet
may touch dangerous voltage and refer servicing to qualified ser-
points or short out parts that could vice personnel under the following
result in a fire or electric shock. Never conditions:
Safety Check: Upon completion of any
service or repairs to this video prod-
uct, ask the service technician to
perform safety checks to determine
that the video product is in proper
operating condition.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
spill liquid of any kind on the video When the power-supply cord or
product.
Ground Clamp
Antenna
plug is damaged.
Lead in Wire
If liquid has been spilled, or objects
have fallen into the video product.
If the video product has been ex-
posed to rain or water.
If the video product has been
dropped or the cabinet has been
damaged.
If the video product does not op-
erate normally be following the
operating instructions. Adjust only
those controls that are covered by
the operating instructions as an im-
proper adjustment of other controls
may result in damage and will often
require extensive work by a qualified
technician to restore the video prod-
uct to its normal operation.
Lightning: For added protection for
this video product receiver during
a lightning storm, or when it is left
unattended and unused for long pe-
Electric
Service
Equipment
Antenna
Discharge Unit riods of time, unplug it from the wall
(NEC SECTION
810-20)
Grounding
Conductors
(NEC SECTION
810-21)
Ground
Clamps
outlet and disconnect the antenna
or cable system. This will prevent
damage to the video product due to
lightning and power-line surges.
Power Service
Grounding Electrode
System (NEC ART 250.
PART H)
When the video product exhibits a
distinct change in performance - this
indicates a need for service.
iii
For Your Safety
Be sure to read this notes before using
Safety Notes
WARNING
Do not allow water or foreign objects to enter the camera.
If water or foreign objects get inside the camera, turn the camera
off, remove the battery and disconnect and unplug the AC power
adapter.
• Make sure that you use your camera correctly. Read these Safety Notes and
your Owner’s Manual carefully before use.
Avoid
exposure to
water
Continued use of the camera can cause a fire or electric shock.
• Contact your FUJIFILM dealer.
• After reading these Safety Notes, store them in a safe place.
About the Icons
Do not use the camera in the bathroom or shower.
This can cause a fire or electric shock.
The icons shown below are used in this document to indicate the severity of
the injury or damage that can result if the information indicated by the icon
is ignored and the product is used incorrectly as a result.
Do not use in
the bathroom
or shower.
Never attempt to disassemble or modify (never open the case).
Failure to observe this precaution can cause fire or electric shock.
This icon indicates that death or serious injury can result if the infor-
mation is ignored.
Do not disas-
semble
WARNING
Should the case break open as the result of a fall or other accident, do not
touch the exposed parts.
Failure to observe this precaution could result in electric shock or in
injury from touching the damaged parts. Remove the battery im-
mediately, taking care to avoid injury or electric shock, and take the
product to the point of purchase for consultation.
This icon indicates that personal injury or material damage can result
if the information is ignored.
CAUTION
Do not touch
internal
parts
The icons shown below are used to indicate the nature of the information
which is to be observed.
Triangular icons tell you that this information requires attention (“im-
portant”).
Do not change, heat or unduly twist or pull the connection cord and do not
place heavy objects on the connection cord.
These actions could damage the cord and cause a fire or electric
shock.
• If the cord is damaged, contact your FUJIFILM dealer.
Circular icons with a diagonal bar tell you that the action indicated is
prohibited (“Prohibited”).
Filled circles with an exclamation mark tell you an action that must be
performed (“Required”).
Do not place the camera on an unstable surface.
This can cause the camera to fall or tip over and cause injury.
Never attempt to take pictures while in motion.
Do not use the camera while you are walking or driving a vehicle. This
can result in you falling down or being involved in a traffic accident.
Do not touch any metal parts of the camera during a thunderstorm.
This can cause an electric shock due to induced current from the
lightning discharge.
WARNING
If a problem arises, turn the camera off, remove the battery, disconnect and
unplug the AC power adapter.
Continued use of the camera when it is emitting smoke, is emitting
any unusual odor, or is in any other abnormal state can cause a fire
Unplug
from power
socket.
or electric shock.
Do not use the battery except as specified.
Load the battery as aligned with the indicator.
• Contact your FUJIFILM dealer.
iv
For Your Safety
WARNING
CAUTION
Do not heat, change or take apart the battery. Do not drop or subject the bat-
tery to impacts. Do not store the battery with metallic products. Do not use
chargers other than the specified model to charge the battery.
Any of these actions can cause the battery to burst or leak and cause
fire or injury as a result.
Keep out of the reach of small children.
This product could cause injury in the hands of a child.
Do not place heavy objects on the camera.
This can cause the heavy object to tip over or fall and cause injury.
Do not move the camera while the AC power adapter is still connected. Do not
pull on the connection cord to disconnect the AC power adapter.
This can damage the power cord or cables and cause a fire or electric
shock.
Do not use the AC power adapter when the plug is damaged or the plug socket
connection is loose.
Use only the battery or AC power adapters specified for use with this camera.
Do not use voltages other than the power supply voltage shown.
The use of other power sources can cause a fire.
If the battery leaks and fluid gets in contact with your eyes, skin or clothing.
Flush the affected area with clean water and seek medical attention or call an
emergency number right away.
This could cause a fire or electric shock.
Do not use the charger to charge batteries other than those specified here.
The Ni-MH battery charger is designed for FUJIFILM HR-AA Ni-MH
batteries. Using the charger to charge conventional batteries or other
types of rechargeable batteries can cause the battery to leak fluid,
overheat or burst.
Do not cover or wrap the camera or the AC power adapter in a cloth or blanket.
This can cause heat to build up and distort the casing or cause a fire.
When you are cleaning the camera or you do not plan to use the camera for
an extended period, remove the battery and disconnect and unplug the AC
power adapter.
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
Failure to do so can cause a fire or electric shock.
When charging ends, unplug the charger from the power socket.
Leaving the charger plugged into the power socket can cause a fire.
When carrying the battery, install it in a digital camera or keep it in the hard
case. When storing the battery, keep it in the hard case. When discarding,
cover the battery terminals with insulation tape.
Contact with other metallic objects or battery could cause the bat-
tery to ignite or burst.
Using a flash too close to a person’s eyes may temporarily affect the eyesight.
Take particular care when photographing infants and young chil-
dren.
When a memory card is removed, the card could come out of the slot too quick-
ly. Use your finger to hold it and gently release the card.
Keep Memory Cards out of the reach of small children.
Because Memory Cards are small, they can be swallowed by children.
Be sure to store Memory Cards out of the reach of small children. If
a child swallows a Memory Card, seek medical attention or call an
emergency number.
Request regular internal testing and cleaning for your camera.
Build-up of dust in your camera can cause a fire or electric shock.
• Contact your FUJIFILM dealer to request internal cleaning every 2
years.
• Please note this is not a free of charge service.
CAUTION
Remove your fingers from the flash window before the flash fires.
Failure to observe this precaution could result in burns.
Do not use this camera in locations affected by oil fumes, steam, humidity or
dust.
Keep the flash window clean and do not use the flash if the window is ob-
structed.
Failure to observe these precautions could cause smoke or discolor-
ation.
This can cause a fire or electric shock.
Do not leave this camera in places subject to extremely high temperatures.
Do not leave the camera in locations such as a sealed vehicle or in
direct sunlight. This can cause a fire.
v
For Your Safety
If you are using a heating pad, take
care not to place the battery di-
rectly against the pad. The camera
may not operate if you use a de-
pleted battery in cold conditions.
• Dispose of used battery promptly.
• Do not drop the battery or other-
wise subject it to strong impacts.
• Do not expose the battery to wa-
ter.
■ Battery Life
Power Supply and Battery
At normal temperatures, the bat-
tery can be used at least 300 times.
If the time for which the battery
provides power shortens markedly,
this indicates that the battery has
reached the end of its effective life
and should be replaced.
* Confirm your battery type before read-
ing the following descriptions.
The following explains proper use of
batteries and how to prolong their
• Always keep the battery terminals
clean.
life. Incorrect use of batteries can ■ Charging the Battery
cause shorter battery life, as well as • You can charge the battery using
• Do not store batteries in hot plac-
es. Also, if you use the battery for
a long period, the camera body
and the battery itself will become
warm. This is normal. Use the AC
power adapter if you are taking
pictures or viewing images for a
long period of time.
leakage, excessive heat, fire or explo-
sion.
the battery charger (included).
- The battery can be charged
at ambient temperatures be-
tween 0°C and +40°C (+32°F
and +104°F). Refer to the Owner’s
Manual for the time of charging
battery.
- You should charge the battery
at an ambient temperature be-
tween +10°C and +35°C (+50°F
and +95°F). If you charge the
battery at a temperature outside
this range, charging takes longer
because the performance of the
battery is impaired.
- You cannot charge the battery
at temperatures of 0°C (+32°F) or
below.
• The Rechargeable Lithium-ion Bat-
tery does not need to be fully dis-
charged or exhausted flat before
being charged.
■ Notes on storage
• If a battery is stored for long periods
while charged, the performance of
the battery can be impaired. If the
battery will not be used for some
time, run the battery out before
storing it.
• If you do not intend to use the
camera for a long period of time,
remove the battery from the cam-
era.
• Store the battery in a cool place.
- The battery should be stored in
a dry location with an ambient
temperature between +15°C and
+25°C (+59°F and +77°F).
Camera uses the Rechargeable
Lithium-ion Battery
1
* When shipped, the battery is not
fully charged. Always charge the
battery before using it.
* When carrying the battery, install it
in a digital camera or keep it in the
soft case.
Camera uses AA-size alkaline or Ni-MH
(nickel-metal hydride) rechargeable
batteries
2
■ Battery Features
* For details on the batteries that
you can use, refer to the Owner’s
Manual of your camera.
• The battery gradually loses its
charge even when not used. Use
a battery that has been charged
recently (in the last day or two) to
take pictures.
■ Cautions for Using Battery
• Do not heat the batteries or throw
them into a fire.
- Do not leave the battery in hot or
extremely cold places.
• To maximize the life of the battery,
turn the camera off as quickly as
possible when it is not being used.
• The number of available frames will
be lower in cold locations or at low
temperatures. Take along a spare
fully charged battery. You can also
increase the amount of power pro-
duced by putting the battery in
your pocket or another warm place
to heat it and then loading it into
the camera just before you take a
picture.
• Do not carry or store batteries with
metal objects such as necklaces or
hairpins.
• Do not expose the batteries to wa-
ter, and keep batteries from getting
wet or stored in moist locations.
• Do not attempt to take apart or
change the batteries, including
battery casings.
• Do not subject the batteries to
strong impacts.
• Do not use batteries that are leak-
ing, deformed, discolored.
■ Handling the Battery
Cautions for Your Safety:
• Do not carry or store battery with
metal objects such as necklaces or
hairpins.
• Do not heat the battery or throw it
into a fire.
• Do not attempt to take apart or
change the battery.
• Do not recharge the battery with
chargers other those specified.
• The battery may feel warm after it
has been charged or immediately
after being used. This is perfectly
normal.
• Do not recharge a fully charged
battery.
vi
For Your Safety
• Do not store batteries in warm or
humid places.
• Keep the batteries out of reach of
babies and small children.
• Make sure that the battery polarity
(Cand D) is correct.
• Do not use new with used batter-
ies. Do not use charged and dis-
charged batteries together.
If any liquid at all leaks from
the batteries, wipe the battery
compartment thoroughly and
then load new batteries.
• Ni-MH batteries have
a
limited
CAUTION
service life. If a battery can only
be used for a short time even after
repeated discharge-charge cycles,
it may have reached the end of its
service life.
Do not use the “Discharging re-
chargeable batteries” function when
alkaline batteries being used.
• To charge Ni-MH batteries, use the
quick battery charger (sold sepa-
rately). Refer to the instructions
supplied with the charger to make
sure that the charger is used cor-
rectly.
If any battery fluid comes into
contact with your hands or
clothing, flush the area thor-
oughly with water. Note that
battery fluid can cause loss
of eyesight if it gets into your
eyes. If this occurs, do not rub
your eyes. Flush the fluid out
with clean water and contact
your physician for treatment.
■ Disposing of Batteries
• When disposing of batteries, do
so in accordance with your local
waste disposal regulations.
• Do not use different types or
brands of batteries at the same
time.
• Do not use the battery charger to
charge other batteries.
• Note that the batteries feel warm
after being charged.
Notes on both models (
,
)
3
1
2
• If you do not intend to use the
camera for a long period of time,
remove the batteries from the
camera. Note if the camera is left
with the batteries removed, the
time and date settings are cleared.
• The batteries feel warm right af-
ter being used. Before removing
the batteries, turn the camera off
and wait for the batteries to cool
down.
• Since batteries do not work well in
cold weather or locations, warm
the batteries by placing them in-
side your garments before use.
Batteries do not work well when
cold. They will work again when
the temperature returns to normal.
• Soil (such as fingerprints) on the
battery terminals makes the bat-
teries charge less reducing the
number of images. Carefully wipe
the battery terminals with a soft
dry cloth before loading.
■ AC Power Adapter
Always use the AC Power Adapter
with the camera. The use of an AC
Power adapter other than FUJIFILM
AC Power Adapter can be damaged
to your digital camera.
For details on the AC power adapter,
refer to the Owner’s Manual of your
camera.
• Due to the way the camera is con-
structed, a small amount of current
is used even when the camera is
turned off. Note in particular that
leaving Ni-MH batteries in the
camera for a long period will over-
discharge the batteries and may
render them unusable even after
recharging.
• Ni-MH batteries will self-discharge
even when not used, and the time
for which they can be used may be
shortened as a result.
• Ni-MH batteries will deteriorate
rapidly if over-discharged (e.g.
by discharging the batteries in a
flashlight). Use the “Discharging re-
chargeable batteries” function pro-
vided in the camera to discharge
the batteries.
■ Using the AA-size Ni-MH batteries
correctly
• Ni-MH batteries left unused in
storage for long periods can be-
come “deactivated”. Also, repeat-
edly charging Ni-MH batteries
that are only partially discharged
can cause them to suffer from the
“memory effect”. Ni-MH batteries
that are “deactivated” or affected
by “memory” suffer from the prob-
lem of only providing power for a
short time after being charged. To
prevent this problem, discharge
and recharge them several times
using the camera’s “Discharging
rechargeable batteries” function.
Deactivation and memory are spe-
cific to Ni-MH batteries and are not
in fact battery faults.
• Use the AC power adapter for in-
door use only.
• Plug the connection cord plug se-
curely into the DC input terminal.
• Turn off the FUJIFILM Digital cam-
era before disconnecting the cord
from the DC input terminal. To dis-
connect, pull out the plug gently.
Do not pull on the cord.
• Do not use the AC power adapter
with any device other than your
camera.
• During use, the AC power adapter
will become hot to the touch. This
is normal.
See Owner’s Manual for the proce-
dure for “Discharging rechargeable
batteries”.
vii
For Your Safety
• Do not take apart the AC power unless intended only for personal Although the LCD panel is produced
adapter. Doing so could be dan- use. Note that some restrictions ap- with highly sophisticated technolo-
■ Explanation of Color Television
System
NTSC: National Television System
Committee, color television
gerous.
• Do not use the AC power adapter performances, entertainments and permanently lit spots. This is not a
in a hot and humid place. exhibits, even when intended purely malfunction, and does not affect re-
• Do not subject the AC power for personal use. Users are also asked corded images.
adapter to strong shocks. to note that the transfer of Memory
• The AC power adapter may emit a Card containing images or data pro-
ply to the photographing of stage gies, there may be black spots or
telecasting
specifications
adopted mainly in the U.S.A.,
Canada and Japan.
■ Trademark Information
xD-Picture Card and Eare trade- PAL: Phase Alternation by Line, a
humming. This is normal.
• If used near a radio, the AC power permissible within the restrictions
adapter may cause static. If this imposed by those copyright laws.
happens, move the camera away
from the radio.
tected under copyright laws is only
marks of FUJIFILM Corporation. The
typefaces included herein are solely
developed by DynaComware Tai-
wan Inc. Macintosh, QuickTime, and
color television system ad-
opted mainly by European
countries and China.
■ Handling Your Digital Camera
■ Exif Print (Exif ver. 2.3)
To ensure that images are recorded Mac OS are trademarks of Apple Inc.
correctly, do not subject the camera in the U.S.A. and other countries.
to impact or shock while an image is Windows 7, Windows Vista, and the
Exif Print Format is a newly revised
digital camera file format that con-
tains a variety of shooting informa-
tion for optimal printing.
Before Using the Camera
Do not aim the camera at extremely
bright light sources, such as the sun
in a cloudless sky. Failure to observe
this precaution could damage the
camera image sensor.
being recorded.
Windows logo are trademarks of
the Microsoft group of companies.
Adobe and Adobe Reader are either
trademarks or registered trademarks
of Adobe Systems Incorporated in
the U.S.A. and/or other countries.
The SDHC and SDXC logos are trade-
marks of SD-3C, LLC. The HDMI logo
is a trademark. YouTube is a trade-
mark of Google Inc. All other trade
names mentioned in this manual are
the trademarks or registered trade-
marks of their respective owners.
■ Liquid Crystal
If the LCD monitor is damaged, take
particular care with the liquid crystal
in the monitor. If any of the follow-
ing situations arise, take the urgent
action indicated.
IMPORTANT NOTICE: Read Before
Using the Software
Direct or indirect export, in whole or
in part, of licensed software without
the permission of the applicable
governing bodies is prohibited.
■ Test Shots Prior to Photography
For important photographs (such as
weddings and overseas trips), always
take a test shot and view the im-
age to make sure that the camera is
working normally.
• FUJIFILM Corporation cannot ac-
cept liability for any incidental
losses (such as the costs of photog-
raphy or the loss of income from
photography) incurred as a result
of faults with this product.
• If liquid crystal comes in contact
with your skin:
Wipe the area with
a
cloth and
then wash thoroughly with soap
and running water.
• If liquid crystal gets into your eye:
Flush the affected eye with clean ■ Notes on Electrical Interference
water for at least 15 minutes and If the camera is to be used in hos-
then seek medical assistance.
• If liquid crystal is swallowed:
pitals or aircrafts, please note that
this camera may cause interference
Flush your mouth thoroughly with to other equipment in the hospital
water. Drink large quantities of wa- or aircraft. For details, please check
ter and induce vomiting. Then seek with the applicable regulations.
medical assistance.
■ Notes on Copyright
Images recorded using your digital
camera system cannot be used in
ways that infringe copyright laws
without the consent of the owner,
viii
For Your Safety
• You are cautioned that any changes or modifications In Countries Outside the European Union, Norway, Iceland and
not expressly approved in this manual could void the Liechtenstein: If you wish to discard this product, includ-
NOTICES
To prevent fire or shock hazard, do not expose the unit
to rain or moisture.
user’s authority to operate the equipment.
ing the batteries or accumulators, please contact your
local authorities and ask for the correct way of disposal.
Notes on the Grant: To comply with Part 15 of the FCC
Rules, this product must be used with a Fujifilm-spec-
ified ferrite-core A/V cable, USB cable, and DC supply
cord.
Please read the “Safety Notes” and make sure you un-
derstand them before using the camera.
EC Declaaratioon of Coonformity
We
Perchlorate Material—special handling may apply. See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
Name:
Address:
FUJIFILM Electronic Imaging Europe GmbH
Benzstrasse 2 47533 Kleve, Germany
For Customers in Canada
CAUTION: This Class B digital apparatus complies with
Canadian ICES-003.
declare that the product
Product Name: FUJIFILM DIGITAL CAMERA X10
Manufacturer’s
For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Name:
Manufacturer’s 7-3, AKASAKA 9-CHOME, MINATO-KU,
Address: TOKYO, 107-0052 JAPAN
conforms to the following Standards:
FUJIFILM Corporation
Disposall of Electrical and Electronic Equipment in Private
Houseeholds
FCC Statement: This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful in-
terference, and (2) this device must accept any interfer-
ence received, including interference that may cause
undesired operation.
In the European Union, Norway, Iceland and Liech-
tenstein: This symbol on the product, or in
the manual and in the warranty, and/or on
its packaging indicates that this product
shall not be treated as household waste.
Instead it should be taken to an applicable
collection point for the recycling of electri-
cal and electronic equipment.
Safety:
EMC:
EN60065: 2002 + A1: 2006 + A11: 2008
EN55022: 2006 + A1: 2007 Class B
EN55024: 1998 + A1: 2001 + A2: 2003
EN61000-3-2: 2006
CAUTION: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in ac-
cordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
EN61000-3-3: 2008
following the provision of the EMC Directive (2004/108/EC)
and Low Voltage Directive (2006/95/EC).
By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences to
the environment and human health, which could oth-
erwise be caused by inappropriate waste handling of
this product.
Kleve,
Germany
October 1, 2011
This symbol on the batteries or accumula-
tors indicates that those batteries shall not
be treated as household waste.
Place
Date
Signature, Managing
Director
If your equipment contains easy removable batteries or
accumulators please dispose these separately accord-
ing to your local requirements.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
The recycling of materials will help to conserve natural
resources. For more detailed information about recy-
cling this product, please contact your local city office,
your household waste disposal service or the shop
where you purchased the product.
ix
About This Manual
Before using the camera, read this manual and the warnings on pages ii–ix. For information on specific
topics, consult the sources below.
✔Table of Contents .............................................. Pxi ✔Troubleshooting .............................................P111
The “Table of Contents” gives an overview of the Having a specific problem with the camera? Find
entire manual. The principal camera operations the answer here.
are listed here.
✔Warning Messaaggeess aanndd DDiissppllaayyss ..................... P116
Find out what’s behind that flashing icon or error
message in the display.
Memory Cards
Pictures can be stored in the camera’s internal memory or on optional SD, SDHC, and SDXC memory cards
(P14), referred to in this manual as “memory cards”.
Temperature Warning
The camera will turn off automatically before its temperature or the temperature of the battery rise above safe
limits. Pictures taken when a temperature warning is displayed may exhibit higher levels of “noise” (mottling).
Turn the camera off and wait for it to cool before turning it on again.
Camera body care
For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body after each use. Do not
use alcohol, thinner, or other volatile chemicals, which could discolor or deform the leather on the camera body.
Any liquid on the camera should be removed immediately with a soft, dry cloth.
x
Table of Contents
For Your Safety ................................................................................. ii
IMPORTANT SAFETY INSTRUCTIONS...................................... ii
Safety Notes.................................................................................... iv
About This Manual.......................................................................... x
Adv. ADVANCED...........................................................................29
SP SCENE POSITION ....................................................................33
Focus Lock.........................................................................................34
The AFL/AEL Button..........................................................................35
Locking Exposure......................................................................35
Locking Focus.............................................................................35
F Macro and Super Macro Modes (Close-ups)................36
N Using the Flash (Super-Intelligent Flash).......................37
J Using the Self-Timer...............................................................39
Continuous Shooting (Burst Mode/Bracketing)..............40
d Exposure Compensation.....................................................44
Metering ............................................................................................45
Focus Mode ......................................................................................46
Focus Frame Selection ................................................................48
White Balance..................................................................................49
The Fn Button..................................................................................51
b Intelligent Face Detection..................................................52
n Face Recognition ....................................................................53
Adding New Faces .......................................................................53
Viewing, Editing, and Deleting Existing Data ...................54
Taking RAW pictures....................................................................55
Beffoore Yoou Beggin
Introduction....................................................................................... 1
Symbols and Conventions.......................................................... 1
Supplied Accessories.................................................................... 1
Parts of the Camera....................................................................... 2
Camera Displays .......................................................................... 5
First SSteps
Attaching the Strap ........................................................................ 8
Charging the Battery ...................................................................10
Inserting the Battery and a Memory Card ......................... 11
Turning the Camera on and Off ..............................................15
Basic Setup .......................................................................................17
Basic Photoggrraphy annd Pllayybbacckk
Taking Pictures ...............................................................................18
Viewing Pictures ............................................................................22
More on Pllayback
Mooree on PPhotography
Playback Options...........................................................................56
Continuous Shooting .................................................................56
I Favorites: Rating Pictures ....................................................56
Playback Zoom..............................................................................57
Multi-Frame Playback.................................................................58
A Deleting Pictures ....................................................................59
Viewing Photo Information ......................................................60
Image Search...................................................................................61
Shooting Mode...............................................................................23
P: PROGRAM AE............................................................................24
S: SHUTTER PRIORITY AE...........................................................25
A: APERTURE PRIORITY AE........................................................25
M: MANUAL ....................................................................................26
C1/C2: CUSTOM MODE ..............................................................27
EXR (E AUTO/E Priority) .......................................28
BAUTO ..........................................................................................29
xi
Table of Contents
T IMAGE QUALITY.....................................................................84
U DYNAMIC RANGE ..................................................................84
P FILM SIMULATION.................................................................85
d WB SHIFT ..................................................................................85
f COLOR........................................................................................85
H SHARPNESS..............................................................................85
r HIGHLIGHT TONE ..................................................................85
s SHADOW TONE ......................................................................85
h NOISE REDUCTION................................................................85
R INTELLIGENT DIGITAL ZOOM............................................86
Z ADVANCED ANTI BLUR........................................................86
b FACE DETECTION...................................................................86
F AF MODE...................................................................................86
n FACE RECOGNITION..............................................................87
I FLASH.........................................................................................87
g EXTERNAL FLASH..................................................................87
K CUSTOM SET............................................................................87
v DISP. CUSTOM SETTING ......................................................88
W MOVIE MODE ..........................................................................88
F AF MODE (F mode) ............................................................88
Using the Menus: Playback Mode..........................................89
Using the Playback Menu..........................................................89
Playback Menu Options.............................................................89
X PHOTOBOOK ASSIST............................................................89
b IMAGE SEARCH.......................................................................89
x ERASE.........................................................................................89
j MARK FOR UPLOAD TO .......................................................89
I SLIDE SHOW ............................................................................90
j RAW CONVERSION................................................................91
B RED EYE REMOVAL................................................................92
D PROTECT...................................................................................92
X PhotoBook Assist ...................................................................62
Creating a PhotoBook ................................................................62
Viewing PhotoBooks ..................................................................63
Editing and Deleting PhotoBooks.........................................63
Viewing Panoramas......................................................................64
Movies
Recording Movies..........................................................................65
Movie Frame Size .........................................................................66
a Viewing Movies........................................................................67
Connecctions
Viewing Pictures on TV...............................................................68
Printing Pictures via USB............................................................70
Connecting the Camera ............................................................70
Printing Selected Pictures ........................................................70
Printing the DPOF Print Order.................................................71
Creating a DPOF Print Order....................................................73
Viewing Pictures on a Computer............................................76
Installing the Software...............................................................76
Connecting the Camera ............................................................80
Menus
Using the Menus: Shooting Mode .........................................82
Using the Shooting Menu.........................................................82
Shooting Menu Options............................................................82
A E MODE ..........................................................................82
A Adv. MODE..............................................................................82
A
SCENE POSITION.....................................................................82
N ISO...............................................................................................82
O IMAGE SIZE...............................................................................83
xii
Table of Contents
G CROP ..........................................................................................93
O RESIZE ........................................................................................93
C IMAGE ROTATE........................................................................94
E COPY...........................................................................................94
F VOICE MEMO...........................................................................95
n ERASE FACE RECOG. .............................................................95
K PRINT ORDER (DPOF)...........................................................95
J DISP. ASPECT ...........................................................................96
The Setup Menu.............................................................................97
Using the Setup Menu................................................................97
Setup Menu Options...................................................................98
F DATE/TIME ...............................................................................98
N TIME DIFFERENCE..................................................................98
L a.................................................................................98
o SILENT MODE..........................................................................98
R RESET .........................................................................................99
K FORMAT ....................................................................................99
A IMAGE DISP. .............................................................................99
B FRAME NO............................................................................. 100
G OPERATION VOL. ................................................................ 100
H SHUTTER VOLUME ............................................................. 100
e SHUTTER SOUND................................................................ 100
I PLAYBACK VOLUME............................................................101
J LCD BRIGHTNESS.................................................................101
M AUTO POWER OFF...............................................................101
1 QUICK START MODE...........................................................101
F Fn BUTTON ............................................................................101
L DUAL IS MODE......................................................................101
B RED EYE REMOVAL..............................................................102
C AF ILLUMINATOR .................................................................102
k AE/AF-LOCK MODE.............................................................102
v AE/AF-LOCK BUTTON ........................................................102
j RAW ..........................................................................................102
j FOCUS CHECK.......................................................................102
I FOCUS CONTROL DIAL..................................................... 103
M FOCUS SCALE UNITS ......................................................... 103
z FRAMING GUIDLINE .......................................................... 103
J COLOR SPACE....................................................................... 104
t SAVE ORG IMAGE................................................................ 104
m AUTOROTATE PB ................................................................. 104
O BACKGROUND COLOR...................................................... 104
c GUIDANCE DISPLAY........................................................... 104
Q VIDEO SYSTEM..................................................................... 104
S CUSTOM RESET ................................................................... 105
x POWER MANAGEMENT .................................................... 105
Techniiccaall NNoottees
Optional Accessories................................................................. 106
Accessories from FUJIFILM .....................................................107
Attaching the Lens Hoods..................................................... 109
Attaching the Filters
(available from third-party suppliers) ............................... 109
Caring for the Camera ...............................................................110
Troublesshooting
Problems and Solutions ...........................................................111
Warning Messages and Displays..........................................116
Apppendix
Internal Memory/Memory Card Capacity ........................120
Specifications................................................................................121
Restrictions on Camera Settings..........................................126
Shooting Mode and Camera Settings................................126
xiii
Memo
xiv
Introduction
Symbols and Conventions
The following symbols are used in this manual:
3: This information should be read before use to ensure correct operation.
1: Points to note when using the camera.
2: Additional information that may be helpful when using the camera.
P: Other pages in this manual on which related information may be found.
Menus and other text in the camera monitor are shown in bold. In the illustrations in this manual, the
monitor display may be simplified for explanatory purposes.
Supplied Accessories
The following items are included with the camera:
NP-50 rechargeable battery
BC-45W battery charger
Clip attaching tool
USB cable
Lens cap
• Owner’s Manual
(this manual)
• Shoulder strap
• Protective covers (× 2)
CD-ROM
Metal strap clips (× 2)
1
Introduction
Parts of the Camera
For more information, refer to the page listed to the right of each item.
1
2
3
4
5
6
7
8
9
Shutter button...........................................20 10 Zoom ring.....................................................19 18 Terminal cover............................68, 70, 80
Exposure compensation dial........... 44 ON/OFF switch ..........................................15 19 DC coupler cable cover.....................107
Mode dial......................................................23 11 Lens.................................................................110 20 Battery-chamber cover latch............11
Microphone (L/R).....................................65 12 AF-assist illuminator ............................102 21 Battery-chamber cover........................11
Hot shoe ..............................................87, 106
Self-timer lamp..........................................39 22 Speaker....................................................67, 95
Viewfinder window.................................. 6 13 Fn (Function) button..............................51 23 Tripod mount
Flash..................................................................37 14 Battery latch .........................................11, 13 24 Monitor............................................................. 5
Strap eyelet.................................................... 8 15 Memory card slot.....................................12 25 USB cable connector.............68, 70, 80
Focus mode selector.............................46 16 Battery chamber.......................................11 26 Connector for HDMI cable.................68
17 Main-command dial................................. 4
2
Introduction
27 Diopter adjustment control ................ 4 33 Indicator lamp............................................21
28 N (flash pop-up) switch.......................37 34 AFL/AEL (autoexposure/autofocus lock) but-
29 a (playback) button..........................15, 22
ton .............................................................35, 47
30 AE (autoexposure) button............................45 35 Selector button (see below)
k (playback zoom in) button.....................57 36 Sub-command dial................................... 4
31 AF (autofocus) button...................................48 37 RAW button...................................................55
n (playback zoom out) button ..................57 38 DISP (display)/BACK button .................6, 21
32 WB (white balance) button..........................49
The Selector Button
Move cursor up (e)
DRIVE button (P40)/
b (delete) button (P22)
MENU/OK button (P17)
Move cursor left (g)
F (macro) button (P36)
Move cursor right (h)
N (flash) button (P37)
Move cursor down (f)
h (self-timer) button (P39)
3
Introduction
Main-command dial/Sub-command dial
Control Lock
Rotate the main/sub-command dial to set the aper-
ture value or shutter speed. You can also select items
using the main/sub-command dial for the selector
button. To adjust focus for MF, rotate the sub-com-
mand dial (P46).
To lock the RAW button and selector button (DRIVE/
N/h/F), press MENU/OK until X is displayed. This
prevents accidental operation during shooting. The
controls can be unlocked by pressing MENU/OK until
Xis no longer displayed.
Diopter adjustment control
The camera is equipped with diopter adjustment to
accommodate individual differences in vision. Slide
the diopter adjustment control up and down until the
viewfinder display is in sharp focus.
Main-command Sub-command
dial
dial
Press the center of the main-command
dial for some operations such as switch-
ing the setting item in M mode.
4
Introduction
Camera Displayys
The following indicators may appear during shooting and playback. The indicators displayed vary with
camera settings.
■ Shooottiinngg
1
2
3
4
5
6
7
8
9
Flash mode...................................................37 16 Focus warning .................................20, 116
Macro (close-up) mode........................36 17 Silent mode indicator.................... 21, 98
Self-timer indicator .................................39 18 Distance indicator....................................46
Continuous shooting mode .............40 19 Battery level.................................................16
Advanced Anti Blur.........................29, 86 20 Sensitivity......................................................82
White balance ............................................49 21 Aperture.................................................25, 26
Film simulation..........................................85 22 AE lock indicator.......................................35
Dynamic range......................................... 84 23 Shutter speed.....................................25, 26
Internal memory indicator*
24 Metering........................................................45
10 Number of available frames...........120 25 Shooting mode.........................................23
11 Image size/quality ...........................83, 84 26 Manual focus indicator.........................46
12 Temperature warning....................x, 116 27 Exposure indicator................................. 44
13 Blur warning......................................38, 116 28 Histogram....................................................... 7
14 Electronic level ..........................................88 29 Focus frame.................................................34
15 Dual IS mode ........................................... 101 30 Intelligent digital zoom........................86
* a: indicates that no memory card
is inserted and that pictures will
be stored in the camera’s internal
memory (P12).
■ Playback
1
2
Favorites.........................................................56
Intelligent Face Detection
indicator.................................................52, 92 10 Playback mode indicator ............22, 56
Red-eye removal indicator.................92 11 Portrait enhancer.....................................33
Pro focus mode, pro low-light
8
Dynamic range......................................... 84
9 E mode..............................................28
3
4
12 Mark for upload to...................................89
mode ........................................................31, 32 13 Photobook assist......................................62
Motion panorama z..................30, 64 14 Voice memo indicator...........................95
Frame number........................................100 15 DPOF print indicator..............................71
Gift image.....................................................56 16 Protected image.......................................92
5
6
7
5
Introduction
3
■ Diisplaay mode
Press DISP/BACK to cycle through display modes as fol-
While INFO DISPLAY or LCD SWITCHED OFF is select-
ed, the display mode may turn to STANDARD depend-
ing on the operations.
lows:
• Shooting
Custom Display
Choose items for display using vDISP. CUSTOM
SETTING in the shooting menu (P88).
Optical Viewfinder
This display is immune from digital video effects and
allows the subject to be viewed directly with no dis-
play lag. Subjects are always in focus, allowing you to
check their expression at any time.
INFO DISPLAY
STANDARD
c
• No information is displayed.
• The display in the viewfinder may differ slightly
from the final photograph due to parallax.
• The frame coverage is approximately 85% (when as-
pect ratio is 4:3).
LCD SWITCHED OFF
INFORMATION OFF
• You may see part of the lens through the viewfinder
depending on the zoom position.
CUSTOM
6
Introduction
• Playback
Histograms
Histograms show the distribution of tones in the im-
age. Brightness is shown by the horizontal axis, the
number of pixels by the vertical axis.
INFORMATION ON
INFORMATION OFF
Pixel brightness
Shadows
Highlights
Optimal exposure: Pixels are
distributed in an even curve
throughout the tone range.
Overexposed: Pixels are clustered
at the right side of the graph.
.
3
DETAIL INFORMA-
TION
IFAVORITES
Underexposed: Pixels are clustered
at the left side of the graph.
7
Attaching the Strap
Attach the strap clips to the camera and then attach the strap.
Open a strap clip.
Use the clip attaching tool to open a strap
clip as shown.
Pass the clip through the eyelet.
1
3
Rotate the clip fully
through the eyelet until it
clicks closed.
Attach a protective cover.
4
Place a protective cover over the eyelet as
shown, with the black side of the cover to-
ward the camera. Repeat Steps 1–4 for the
second eyelet.
3
Keep the tool in a safe place. You will need it to
open the strap clips when removing the strap.
Place the strap clip on an eyelet.
Hook the strap eyelet in the clip opening.
Remove the tool, using the other hand to
keep the clip in place.
2
8
Attaching the Strap
Insert the strap.
Insert the strap through a protective cover
and strap clip.
Fasten the strap.
Fasten the strap as shown. Repeat Steps 5–6
for the second eyelet.
5
6
3
To avoid dropping the camera, be sure the strap is cor-
rectly secured.
9
Charging the Battery
The battery is not charged at shipment. Charge the battery before use.
Place the battery in the supplied battery
charger.
Insert the battery in the orientation indicat-
Plug the charger in.
Plug the charger into an indoor power out-
let. The charging indicator will light.
1
2
ed by the DFC labels.
The Charging Indicator
The charging indicator shows battery charge
status as follows:
The camera uses an NP-50 rechargeable battery.
Charge lamp
Charginng
indicator
Batttteerryy sstaatus
Action
Arrow
Battery not
inserted.
Battery fully
charged.
Battery
Insert the battery.
Off
DFC
Remove the battery.
—
label
On
Battery charging.
Unplug the charger and
remove the battery.
Battery charger
DFClabel
Blinks
Battery fault.
Charge the battery.
3
Remove the battery when charging is com-
plete. See the specifications (P124) for
charging times (note that charging times in-
crease at low temperatures).
3
Unplug the charger when it is not in use.
10
Inserting the Battery and a Memory Card
Although the camera can store pictures in internal memory, optional SD, SDHC, and SDXC memory
cards (sold separately) can be used to store additional pictures. After charging the battery, insert the
battery and memory card as described below.
Open the battery-chamber cover.
Insert the battery.
1
2
Align the orange stripe on the battery with
the orange battery latch and slide the bat-
tery into the camera, keeping the battery
latch pressed to one side. Confirm that the
battery is securely latched.
Orange stripe
a
Be sure the camera is off before opening the bat-
tery-chamber cover.
3
• Do not open the battery-chamber cover when
the camera is on. Failure to observe this pre-
caution could result in damage to image files or
memory cards.
Battery latch
• Do not use excessive force when handling the
battery-chamber cover.
3
Insert the battery in the correct orientation. Do
NOT use force or attempt to insert the battery up-
side down or backwards. The battery will slide in
easily in the correct orientation.
11
Inserting the Battery and a Memory Card
• SD/SDHC/SDXC memory
Insert the memory card.
Holding the mem-
ory card in the ori-
entation shown at
right, slide it in until
it clicks into place
at the back of the
3
cards can be locked, mak-
ing it impossible to format
the card or to record or
delete images. Before in-
serting an SD/SDHC/SDXC
Write-prroteect
switch
memory card, slide the write-protect switch to
the unlocked position.
Click
slot.
Close the battery-chamber cover.
4
3
• Be sure card is in the correct orientation; do not
insert at an angle or use force. If the memory
card is not correctly inserted or no memory
card is inserted, a will appear in the LCD moni-
tor and internal memory will be used for record-
ing and playback.
12
Inserting the Battery and a Memory Card
3Batteries
Removing the Battery and Memory Card
Before removing the battery or memory card, turn
the camera off and open the battery-chamber cover.
To remove the battery, press the
battery latch to the side, and
slide the battery out of the cam-
• Remove dirt from the battery terminals with a clean,
dry cloth. Failure to observe this precaution could
prevent the battery from charging.
• Do not affix stickers or other objects to the battery.
Failure to observe this precaution could make it im-
possible to remove the battery from the camera.
• Do not short the battery terminals. The battery could
overheat.
• Read the cautions in “Power Supply and Battery”
(Pvi).
• Use only battery chargers designated for use with the
battery. Failure to observe this precaution could re-
sult in product malfunction.
era as shown.
Battery latch
To remove the memory card,
press it in and release it slowly.
The card can then be removed
by hand. When a memory card
is removed, the card could come out of the slot too
quickly. Use your finger to hold it and gently release
the card.
• Do not remove the labels from the battery or attempt
to split or peel the outer casing.
• The battery gradually loses its charge when not in
use. Charge the battery one or two days before use.
b Using an AC Power Adapter
• The camera can be powered by an optional AC pow-
er adapter and DC coupler (sold separately). See the
manuals provided with the AC power adapter and DC
coupler for details.
• Depending on the country or region of sale, a demo
mode slide show may start if the camera is turned on
while powered by an AC power adapter. Press the
shutter button to end the show.
13
Inserting the Battery and a Memory Card
• miniSD or microSD adapters that are larger or smaller
than the standard dimensions of an SD/SDHC/SDXC
card may not eject normally; if the card does not
eject, take the camera to an authorized service repre-
sentative. Do not forcibly remove the card.
■ Compatible Memory Cards
FUJIFILM and SanDisk SD, SDHC, and SDXC mem-
ory cards have been approved for use in the cam-
era. A complete list of approved memory cards
is available at http://www.fujifilm.com/support/
digital_cameras/compatibility/. Operation is not
guaranteed with other cards. The camera can not
be used with xD-Picture Cards or MultiMediaCard
(MMC) devices.
• Do not affix labels to memory cards. Peeling labels
can cause camera malfunction.
• Movie recording may be interrupted with some types
of SD/SDHC/SDXC memory card. Use a Gcard
or better when shooting HD or high-speed movies.
• The data in internal memory may be erased or cor-
rupted when the camera is repaired. Please note that
the repairer will be able to view pictures in internal
memory.
• Formatting a memory card or internal memory in the
camera creates a folder in which pictures are stored.
Do not rename or delete this folder or use a comput-
er or other device to edit, delete, or rename image
files. Always use the camera to delete pictures from
memory cards and internal memory; before editing
or renaming files, copy them to a computer and edit
or rename the copies, not the originals.
3Memory Cards
• Do not turn the camera off or remove the memory
card while the memory card is being formatted or
data are being recorded to or deleted from the card.
Failure to observe this precaution could damage the
card.
• Format SD/SDHC/SDXC memory cards before first
use, and be sure to reformat all memory cards af-
ter using them in a computer or other device. For
more information on formatting memory cards, see
“K FORMAT” (P99).
• Memory cards are small and can be swallowed; keep
out of reach of children. If a child swallows a memory
card, seek medical assistance immediately.
14
Turning the Camera on and Off
To turn the camera on, rotate the zoom ring as
shown.
Turning the Camera on in Playback Mode
To turn the camera on and begin playback, press the
a button for about a second.
Rotate the zoom ring to OFF to turn the camera
off.
Press the a button again to turn the camera off.
c
The camera does not exit to shooting mode when
pressing the shutter button.
b Switching to Playback Mode
Press the a button to start playback. Press a button
again or press the shutter button halfway to return to
shooting mode.
c
• If the zoom ring is not fully rotated to OFF, the battery
will drain.
• Pictures can be affected by fingerprints and other
marks on the lens. Keep the lens clean.
15
Turning the Camera on and Off
b Auto Power Off
Battery Level
Battery level is shown as follows:
The camera will turn off automatically if no operations
are performed for the length of time selected in the
M AUTO POWER OFF menu (P101). To reactivate
the camera after it has turned off automatically, rotate
the zoom ring to OFF and then turn the camera on.
Indicator
Description
D (white) Battery partially discharged.
C (white) Battery more than half discharged.
Low battery. Charge as soon as pos-
sible.
B (red)
Battery exhausted. Turn camera off
and charge battery.
A (blinks red)
16
Basic Setup
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as
described below (for information on resetting the clock or changing languages, see page 98).
Highlight a language and press MENU/OK.
1
ENGLISH
FRANCAIS
DEUTSCH
ESPAÑOL
PORTUGUÊS
1
Press DISP/BACK to skip the current step. Any steps you skip will be displayed
the next time the camera is turned on.
The date and time will be displayed. Press the selector left or right to
highlight the year, month, day, hour, or minute and press up or down
to change. To change the order in which the year, month, and day
are displayed, highlight the date format and press the selector up or
down. Press MENU/OK when settings are complete.
DATE / TIME NOT SET
2
3
2013
2012
YY. MM. DD
2011 1.
2009
1
12:00
AM
2010
SET
NO
Power management options will be displayed. Press the selector up
or down to highlight one of the following options and then press
MENU/OK:
• n POWER SAVE: Save battery power.
• o CLEAR DISPLAY: Choose for a brighter, higher quality display.
2 The Camera Clock
If the battery is removed for an extended period, the camera clock will be reset and the language-selection dialog
will be displayed when the camera is turned on.
17
Taking Pictures
This section explains basic photography.
Select a mode.
1
When you rotate the mode dial to EXR, the R display will appear in the LCD monitor.
Scene Icon (P28)
The camera automatically selects the appropriate scene.
The o Icon
In R mode, the camera continuously adjusts focus and searches for faces, increasing the drain on the
battery. o is displayed in the LCD monitor.
1
• The camera analyses the scene and selects the preferred E mode when the shutter button is pressed
halfway (P29).
• To raise the flash when lighting is poor, press the flash pop-up switch (P37).
18
Taking Pictures
Frame the picture.
Holding the Camera
2
Use the zoom ring to
frame the picture in the
display. The zoom indica-
tor appears.
Hold the camera steady with
both hands and brace your
elbows against your sides.
Shaking or unsteady hands
can blur your shots.
Zoom ring
To prevent pictures that are
out of focus or too dark (un-
derexposed), keep your fin-
gers and other objects away
from the lens and flash.
Zoom indicator
2 Focus Lock
Use focus lock (P34) to focus on subjects that are not
in the focus frame.
19
Taking Pictures
2 The Shutter Button
The shutter button has two positions. Pressing the
Focus.
3
4
Press the shutter button halfway
to focus.
shutter button halfway ( ) sets focus and exposure;
q
to shoot, press the shutter button the rest of the way
down ( ).
w
If the camera is able to focus, it will beep twice
and the indicator lamp will glow green.
Double
beep
Click
If the camera is unable to focus, the focus frame
will turn red, s will be displayed, and the
indicator lamp will blink green. Change the
composition or use focus lock (P34).
q
w
Press halfway
Press the rest of
the way down
Shoot.
Smoothly press the shutter but-
ton the rest of the way down to
take the picture.
1
If the subject is poorly lit, the AF-assist illuminator may
light to assist focus (P102). For information on using
the flash when lighting is poor, see page 37.
20
Taking Pictures
Silent Mode
The Indicator Lamp
In situations in which camera sounds or lights may be
unwelcome, hold the DISP/BACK button down until o
is displayed.
Indicator lamp
The indicator lamp shows camera status as follows:
Indiicattor lamp Camera staattuuss
Glows green Focus locked.
Blur, focus, or exposure warning. Pic-
ture can be taken.
Blinks green Recording pictures. Additional pic-
and orange tures can be taken.
Blinks green
The camera speaker, flash, and AF-assist illuminator/
self-timer lamp turn off and flash and volume settings
can not be adjusted (note that the flash will still fire
when C is selected in scene mode). To restore nor-
mal operation, press the DISP/BACK button until the o
icon is no longer displayed.
Glows
orange
Recording pictures. No additional pic-
tures can be taken at this time.
Blinks orange Flash charging; flash will not fire when
(Fast) picture is taken.
Blinks orange The zoom ring is positioned between
(Slow)
ON and OFF. Picture cannot be taken.
Lens or memory error (memory card
Blinks red full or not formatted, format error, or
other memory error).
2 Warnings
Detailed warnings appear in the display. See pages
116–119 for more information.
21
Viewing Pictures
Pictures can be viewed in the monitor. When taking important photographs, take a test shot and
check the results.
Press the a button.
Deleting Pictures
To delete the picture currently displayed
in the monitor, press the selector up (b).
1
To exit without deleting the picture, highlight CAN-
CEL and press MENU/OK.
2 The Playback Menu
Pictures can also be deleted from the playback menu
(P59).
The most recent picture will be displayed in
the monitor.
View additional pictures.
2
Press the selector right to view
pictures in the order recorded, left
to view pictures in reverse order.
Press the shutter button to exit to shooting
mode.
22
Shooting Mode
Choose a shooting mode according to the scene or type of subject. To
choose a shooting mode, rotate the mode dial to the desired setting. The
following modes are available:
P, S, A, M: Select for full control over camera settings, including
aperture (M and A) and/or shutter speed (M and S) (P24).
EXR: Improve clarity, reduce noise, in-
crease dynamic range, or let the camera
automatically adjust settings to suit the
scene (P28).
C1/C2 (CUSTOM): Recall stored settings for
modes P, S, A, M and all EXR modes ex-
cept R (P27).
B
(AUTO):
A
simple “point-and-shoot”
F (MOVIE): Shoot a movie with sound
(P65).
mode recommended for first-time users
of digital cameras (P29).
Adv. (ADVANCED): Sophisticated tech-
niques made easy (P29).
SP (SCENE POSITION): Choose a scene suited to the subject or
shooting conditions and let the camera do the rest (P33).
23
Shooting Mode
P: PROGRAM AE
Program Shift
Rotate the main/sub-command dial to choose the
desired combination of shutter speed and aperture.
The default values can be restored by raising the
flash or turning the camera off. To use program shift,
turn the flash off and select OFF for g EXTERNAL
FLASH. Furthermore, an option other than AUTO
must be selected for U DYNAMIC RANGE and
N ISO.
In this mode, the camera sets exposure
automatically. If desired, you can choose
different combinations of shutter speed
and aperture that will produce the same
exposure (program shift).
3
If the subject is outside the metering range of the cam-
era, the shutter speed and aperture displays will show
“---”. Press the shutter button halfway to measure ex-
posure again.
Shutter speed
Aperture
24
Shooting Mode
S: SHUTTER PRIORITY AE
A: APERTURE PRIORITY AE
Choose the shutter speed using the
main/sub-command dial, while the
camera adjusts aperture for optimal ex-
posure.
Choose the aperture using the main/
sub-command dial, while the camera
adjusts shutter speed for optimal expo-
sure.
Shutter speed
Aperture
3
3
• If the correct exposure can not be achieved at the
selected shutter speed, aperture will be displayed in
red. Adjust shutter speed until the correct exposure
is achieved. If the subject is outside the metering
range of the camera, the aperture display will show
“F---”. Press the shutter button halfway to measure
exposure again.
If the correct exposure can not be achieved at the se-
lected aperture, shutter speed will be displayed in red.
Adjust aperture until the correct exposure is achieved.
If the subject is outside the metering range of the cam-
era, the shutter speed display will show “---”. Press the
shutter button halfway to measure exposure again.
• The shutter speed is restricted depending on the ISO
setting.
25
Shooting Mode
M: MANUAL
Sub-command dial
When an option other than
MF is selected for focus mode
(P 46), you can use the sub-
command dial to set aperture
or shutter speed.
In this mode, you choose both shutter
speed and aperture. If desired, expo-
sure can be altered from the value sug-
gested by the camera.
Rotate the main-command dial to set the shut-
ter speed or aperture. Press the main-command
dial to change the setting item between shutter
speed and aperture.
2000
F5.6
F5.6
1
• Rotating the sub-command
dial changes the setting that
is not marked with 89.
• Press the main-command
dial to change the setting
item.
2000
Shutter speed
Aperture
The Exposure Indicator
1
Rotating the main-command dial changes the setting
marked with 89.
The amount the picture will
be under- or over-exposed at
current settings is shown by
the exposure indicator.
3
• Noise in the form of randomly-spaced bright pixels
may occur in long exposures.
• The shutter speed is restricted depending on the ISO
setting.
26
Shooting Mode
Meenu/settiing
Settinggs saved
C1/C2: CUSTOM MODE
N ISO, O IMAGE SIZE, T IMAGE QUAL-
ITY, U DYNAMIC RANGE, P FILM SIMULA-
TION, d WB SHIFT, f COLOR, H SHARP-
In P, S, A, M and all EXR modes except
R, the K CUSTOM SET option in
the shooting menu (P87) can be used
to save current camera and menu set-
tings. These settings are recalled when-
ever the mode dial is rotated to C1/C2
(custom mode).
Shooting NESS, r HIGHLIGHT TONE, s SHADOW
menu
TONE, h NOISE REDUCTION, R INTELLI-
GENT DIGITAL ZOOM, b FACE DETECTION,
n FACE RECOGNITION, F AF MODE,
I FLASH, g EXTERNAL FLASH
Setupp menu C AF ILLUMINATOR, j RAW
Metering (AE), white balance (WB), burst/brack-
eting mode (DRIVE), macro mode (F), flash
mode (N), program shift, shutter speed, aper-
ture, monitor display options (DISP/BACK)
Other
c
Once the camera is turned off, R INTELLIGENT DIGI-
TAL ZOOM is deactivated.
27
Shooting Mode
EXR (E AUTO/E Priority)
Optimize settings for your current subject or improve clarity, reduce noise, or enhance dy-
namic range. Rotate the mode dial to EXR and choose one of the following E modes
in the shooting menu.
■ R(EAUTO)
The camera automatically selects the scene and E mode according to shooting conditions.
1
If S is selected for O IMAGE SIZE in R mode, the camera will automatically select the optimal image size.
The Scene Icon
The camera selects from the following scenes:
LAND-
SCAPE
SKY &
GREENERY
Scene
AUTO
NIGHT
MACRO
BEACH
SUNSET
SNOOW
SKY
GREENERY
Main subject
Noonn--pportrait
a
d
g
c
a
b
c
d*
dd*
—
e
—
u
v
w
x
y
z
Noorrmal
Backlit
dc
gc
cc
ac
bc
du
gu
cu
au
bu
dv
gv
cv
av
bv
dw
gw
cw
aw
bw
dx
gx
cx
ax
bx
dy
gy
cy
ay
by
dz
gz
cz
az
bz
Portrait
—
Moving object
Portrait and motion
cd
ad
—
ce
Noorrmal
Backlit
—
—
* If nis displayed, the camera will take a series of shots (advanced anti-blur; P29).
3
The mode selected may vary with shooting conditions. If the mode and subject do not match, select Bmode
(P29) or choose SP (P33) and select a scene manually.
28
Shooting Mode
• U (D-RANGE PRIORITY): Increases the amount of
detail visible in highlights.
Advanced Anti Blur
When nis displayed, the camera will take a series of
exposures and combine them to form a single image,
reducing “noise” (mottling) and blur.
■ EPriority
Choose from the following options:
• S (RESOLUTION PRIORITY): Choose for crisp, clear
shots.
• T (HIGH ISO & LOW NOISE): Reduce noise in pic-
tures taken at high sensitivities.
• U (D-RANGE PRIORITY): Increase the amount of
detail visible in highlights.
1
n is available when ON is selected in the shooting
menu (P 86) and the flash (P 37) is off or set to
auto.
3
• Some time may be required to combine the expo-
sures into a single image. A single combined image
may not be created if the subject or camera moves
during shooting. Keep the camera steady during
shooting and do not move the camera until shoot-
ing is complete.
U DYNAMIC RANGE (P 84) can be set to
M (1600%) and D (800%).
BAUTO
Choose for crisp, clear snapshots. This mode is
• Frame coverage is reduced.
recommended in most situations.
The EXR Icon
Adv. ADVANCED
This mode combines “point-and-shoot”
simplicity with sophisticated photograph-
When the shutter button is pressed halfway, the
camera chooses the preferred E mode:
• S (RESOLUTION PRIORITY): Produces crisp, clear
shots.
• T (HIGH ISO & LOW NOISE): Reduces noise in pic-
tures taken at high sensitivities.
ic techniques. The
A
Adv. MODE op-
tion in the shooting menu can be used
to choose from the following advanced
modes:
29
Shooting Mode
1
■ rMOTION PANORAMA 36600
Follow an on-screen guide
to take photos that will
automatically be joined to
form a panorama.
Shooting ends if the shutter button is pressed all the
way down during shooting. No panorama will be re-
corded if the shutter button is pressed before the cam-
era has been panned through 120°.
3
• Do not rotate the zoom ring during shooting.
• Panoramas are created from multiple frames. The
camera may in some cases record a greater or lesser
angle than selected or be unable to stitch the frames
together perfectly. The last part of the panorama
may not be recorded if shooting ends before the
panorama is complete.
Rotate the zoom ring until the zoom indicator
turns white (P19).
1
To select the angle through which you will pan
2
the camera while shooting, press the selector
down. Press the selector left or right to high-
light an angle and press MENU/OK.
• Shooting may be interrupted if the camera is panned
too quickly or too slowly. Panning the camera in a
direction other than that shown cancels shooting.
• The desired results may not be achieved with mov-
ing subjects, subjects close to the camera, unvarying
subjects such as the sky or a field of grass, subjects
that are in constant motion, such as waves and wa-
terfalls, or subjects that undergo marked changes in
brightness. Panoramas may be blurred if the subject
is poorly lit.
Press the selector right to view a choice of pan
directions. Press the selector left or right to
highlight a pan direction and press MENU/OK.
3
Press the shutter button all the way down to
start recording. There is no need to keep the
shutter button pressed during recording.
4
Pan the camera in the di-
120
5
rection shown by the arrow.
Shooting ends automati-
cally when the progress bar
is full and the panorama is
Progress bar
complete.
30
Shooting Mode
■ iPRO FOCUS
z
Choose zfor seamless 360 ° panoramas that can be
played back in a loop (P64).
The camera takes up to three
shots each time the shutter
button is pressed, softening
the background to emphasize
the main subject. The amount
of softening can be adjusted before shooting by
rotating the main/sub-command dial. Use for
portraits or photos of flowers similar to those pro-
duced by SLR cameras.
1
The t SAVE ORG IMAGE option in the setup menu
can be used to record a vpanorama in addition to
a seamless zpanorama (P104).
3
Depending on the subject and shooting conditions,
the camera may produce distorted results or a v
panorama. The top and bottom of the area visible in
the shooting display are cropped out and white strips
may appear at the top and bottom of the display.
1
Softening can not be applied to background objects
that are too close to the main subject. If a message
stating that the camera can not create the effect is
displayed when the camera focuses, try backing away
from your subject and zooming in. The camera may
also be unable to soften the background if the subject
is moving; if prompted, check the results and try again.
For Best Results
For best results, move the camera in a small circle at
a steady speed, keeping the camera horizontal and
being careful only to pan in the direction shown by
the guides. If the desired results are not achieved, try
panning at a different speed.
31
Shooting Mode
■ jPRO LOW-LIGHT
PRO FOCUS/PRO LOW-LIGHT
Each time the shutter button
is pressed, the camera makes
four exposures and combines
them into a single photograph.
Use to reduce noise and blur
when photographing poorly lit subjects or static
subjects at high zoom ratios.
To save unprocessed copies of pictures taken in these
modes, select ON for the t SAVE ORG IMAGE op-
tion in the setup menu (P104).
3
• Keep the camera steady during shooting.
• Frame coverage is reduced.
1
A single combined photograph may not be created
with some scenes or if the subject or camera moves
during shooting. Do not move the camera until shoot-
ing is complete.
32
Shooting Mode
SP SCENE POSITION
The camera offers a choice of “scenes,” each adapted to particular shooting conditions or
a specific type of subject. Use the A SCENE POSITION option in the shooting menu to
choose the scene assigned to the SP position on the mode dial.
Scene
C NATURAL & N
D NATURAL LIGHT
L PORTRAIT
Description
The camera takes two shots: one without the flash and one with.
Capture natural lighting under low-light conditions.
Choose for portraits.
Z PORTRAIT ENHANCER Choose for a smooth skin effect when shooting portraits.
M LANDSCAPE
N SPORT
Choose for daylight shots of buildings and landscapes.
Choose when photographing moving subjects.
O NIGHT
Choose this mode for poorly lit twilight or night scenes.
HNIGHT (TRIPOD)
U FIREWORKS
QSUNSET
RSNOW
V BEACH
f UNDERWATER
U PARTY
Choose this mode for slow shutter speeds when shooting at night.
Slow shutter speeds are used to capture the expanding burst of light from a firework.
Choose this mode to record the vivid colors in sunrises and sunsets.
Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.
Choose for crisp, clear shots that capture the brightness of sunlit beaches.
Reduces the blue cast typically associated with underwater lighting.
Capture indoor background lighting under low-light conditions.
Choose for vivid close-ups of flowers.
V FLOWER
WTEXT
Take clear pictures of text or drawings in print.
33
Focus Lock
To compose photographs with off-center subjects:
Position the subject in the focus frame.
Autofocus
1
2
Although the camera boasts a high-precision autofo-
cus system, it may be unable to focus on the subjects
listed below. If the camera is unable to focus using
autofocus, use focus lock to focus on another subject
at the same distance and then recompose the pho-
tograph.
• Very shiny subjects such as mirrors or car bodies.
• Fast-moving subjects.
• Subjects photographed through a window or other
reflective object.
Focus.
Press the shutter button
halfway to set focus and
exposure. Focus and ex-
posure will remain locked
while the shutter button
is pressed halfway (AF/AE
1000 F3.3
lock).
• Dark subjects and subjects that absorb rather than
reflect light, such as hair or fur.
• Insubstantial subjects, such as smoke or flame.
• Subjects that show little contrast with the back-
ground (for example, subjects in clothing that is the
same color as the background).
Recompose the picture.
3
Keeping the shutter but-
ton pressed halfway, re-
compose the picture.
• Subjects positioned in front of or behind a high-
contrast object that is also in the focus frame (for
example, a subject photographed against a back-
drop of highly contrasting elements).
1000 F3.3
Shoot.
4
34
The AFL/AEL Button
The AFL/AEL button can be used to lock exposure or focus.
Lockingg EExxppoossuure
Recompose the picture.
Keeping the shutter button pressed halfway,
recompose the picture.
3
Meter exposure.
1
Position the subject in the
focus frame and press the
AFL/AEL button to meter
exposure.
c
Adjusting zoom ends AE lock. AE lock is not avail-
able with Intelligent Face Detection.
Focus.
Shoot.
2
4
Keeping the AFL/AEL but-
ton pressed, press the
shutter button halfway
to focus. Focus and ex-
posure will remain locked while the shutter
button is pressed halfway, even if you later
release the AFL/AEL button.
+
Lockiing Focus
If AF LOCK ONLY is selected for v AE/AF-LOCK
BUTTON in the setup menu (P102), pressing
the AFL/AEL button locks focus. If AE/AF LOCK is
selected, both focus and exposure will be locked.
a
Repeat steps 1 and 2 as desired to refocus
before taking the picture.
If AE&AF ON/OFF SWITCH is selected for k AE/
AF-LOCK MODE in the setup menu (P 102), expo-
sure and/or focus will lock when the AFL/AEL button is
pressed and remain locked until the button is pressed
again.
35
F Macro and Super Macro Modes (Close-ups)
For close-ups, press the selector left (F) to choose from the macro options shown below.
Choose from F (macro mode),
G (super macro mode), or
OFF (macro mode off)
When macro mode is in effect, the camera focuses on subjects near the center of the frame. Use the
zoom ring to compose pictures. The following restrictions apply in super macro mode: the lens must
be zoomed all the way out (at other zoom positions, zis displayed) and the flash can not be used.
1
• Use of a tripod is recommended to prevent blur caused by camera shake.
• Flash compensation may be required when using the flash (P87).
• Using the flash at close range may cast a lens shadow. Zoom a little or have more distance from the subject.
• If macro mode is set while display mode is set to INFO DISPLAY or LCD SWITCHED OFF, display mode auto-
matically turns to STANDARD (P6).
• Use of the LCD monitor is recommended to avoid parallax at close range.
• The camera can focus at short range when macro mode is not set, but the time needed to focus increases.
• Rotate the zoom ring until the zoom indicator turns white when using G (P19).
Focus range (distance from front of lens)
• Approx. 50cm (1.6ft.)–infinity (wide angle); 80cm (2.6 ft.)–infinity (telephoto)
• Macro: approx. 10cm–3m/0.3ft.–9.8ft. (wide angle); 50cm–5m/1.6ft.–16.4ft. (telephoto)
• Super macro: approx. 1cm–1m/0.9in.–3.2ft. (wide angle)
36
N Using the Flash (Super-Intelligent Flash)
When the flash is used, the camera’s Super-Intelligent Flash system instantly analyzes the scene based
on such factors as the brightness of the subject, its position in the frame, and its distance from the
camera. Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed
while preserving the effects of ambient background lighting, even in dimly-lit indoor scenes. Use the
flash when lighting is poor, for example when shooting at night or indoors under low light.
Raise the flash.
Slide the flash pop-up switch to raise the flash.
1
Choose a flash mode.
Press the selector right (N). The flash mode changes each time the selector is pressed.
2
Mode
A/K
(AUTO FLASH)
Description
The flash fires when required. Recommended in most situations.
N/L
The flash fires whenever a picture is taken. Use for backlit subjects or for natural
(FORCED FLASH) coloration when shooting in bright light.
O/M
Capture both the main subject and the background under low light (note that
(SLOW SYNCHRO) brightly lit scenes may be overexposed).
37
N Using the Flash (Super-Intelligent Flash)
3
The flash may fire several times with each shot. Do not move the camera until shooting is complete.
1
• The peripheral part of an image may be dark when using the flash.
• Remove lens hoods to prevent shadows in photos taken with the flash.
Red-Eye Removal
When Intelligent Face Detection is active (P52), and ON is selected for B RED EYE REMOVAL in
the setup menu (P102), red-eye removal is available in K, L, and M.
Red-eye removal minimizes “red-eye” caused when light from the flash is reflected from the subject’s
retinas as shown in the illustration at right.
Turning the Flash Off
Lower the flash where flash photography is prohibited or to capture natural lighting un-
der dim light. At slow shutter speeds, k will be displayed to warn that pictures may be
blurred; use of a tripod is recommended.
38
J Using the Self-Timer
To use the self-timer, press the selector down (h) and choose from the following options:
Option
T (OFF)
Description
Self-timer off.
The shutter is released ten seconds after the shutter button is pressed. Use for self-portraits.
The self-timer lamp on the front of the camera lights when the timer starts and begins to
blink shortly before the photo is taken.
S (10 SEC)
The shutter is released two seconds after the shutter button is pressed. Use to reduce blur
caused by the camera moving when the shutter button is pressed. The self-timer lamp will
blink as the timer counts down.
R (2 SEC)
39
Continuous Shooting (Burst Mode/Bracketing)
Capture motion or automatically vary selected settings over a series of pictures.
1
• Focus and exposure are determined by the first frame
in each series. The flash turns off automatically; the
previously-selected flash mode is restored when con-
tinuous shooting is turned off.
Press the selector up (DRIVE) and
choose from the following options:
B: STILL IMAGE
I: TOP
• Frame rate varies with shutter speed.
P: BEST FRAME CAPTURE
O: AE BKT
W: ISO BKT
X: FILM SIMULATION BKT
Y: DYNAMIC RANGE BKT
• The number of pictures that can be taken in a single
burst varies with the scene and camera settings. The
number of pictures that can be recorded depends on
the memory available.
• Use of the viewfinder is recommended to view the
subject directly with no display lag.
• If P is selected in I or P, pictures will be recorded
at size P or smaller.
• If you select 16 frames in P, pictures will be recorded
at size P or smaller.
40
Continuous Shooting (Burst Mode/Bracketing)
Press the selector right when the camera is in
shooting mode.
■ ITOP
1
2
The camera takes photographs while the shutter
button is pressed.
Highlight the current frame rate and press the
selector right, then press selector up or down
to choose a new value and press MENU/OK to
select.
Press the selector right or left to choose the
frame rate.
1
Option
P
Max frame rate
10 fps
3
Some frame rates may reduce the number of shots
available in Step 3.
J
7 fps
5 fps
3 fps
K
O
Highlight the number of
shots and press the selec-
tor right. Press the selector
up or down to choose the
number of shots in each
burst and left or right to
choose their distribution
Shots per burst
The frame rate varies depending on the shoot-
ing conditions or numbers of frames in con-
tinuous shooting.
3
Press MENU/OK to return to shooting mode
when settings are complete.
2
1
Distribution
(the number on the left is taken before and the
number on the right after the shutter button
is pressed). Press MENU/OK when settings are
complete.
When shooting with the self-timer, continuous shoot-
ing is not available.
■ PBEST FRAMMEE CCAAPTURRE
The camera takes a series of pictures, starting
before and ending after the shutter button is
pressed. To choose the frame rate and number
of shots:
41
Continuous Shooting (Burst Mode/Bracketing)
Press DISP/BACK to return to shooting mode.
■ OAE BKT
4
5
Press the selector left or right to highlight a
bracketing amount. Each time the shutter but-
ton is pressed, the camera will take three shots:
one using the metered value for exposure, the
second overexposed by the selected amount,
and the third underexposed by the same amount
(the camera may not be able to use the selected
bracketing increment if the amount of over- or
under- exposure exceeds the limits of the expo-
sure metering system).
Take photographs. The camera begins record-
ing while the shutter button is pressed half-
way, and completes the burst when the shut-
ter button is pressed all the way down. The
illustration shows a burst of eight shots, three
before the shutter button is pressed and four
after.
Shutter button
pressed all the
way down
Shutter button
pressed halfway
■ WISO BKT
Press the selector left or right to highlight a brack-
eting amount. Each time the shutter is released,
the camera will take a picture at the current sen-
sitivity (P82) and process it to create two addi-
tional copies, one with sensitivity raised and the
other with sensitivity lowered by the selected
amount (regardless of the amount selected, sen-
sitivity will not exceed ISO 1600 or fall below ISO
200).
“Before” “After”
shots shots
3
• If the shutter button is pressed all the way down be-
fore the number of frames selected for the “before”
portion is recorded, the remaining frames will be
taken after the shutter button is pressed all the way
down.
• If the shutter button is pressed halfway for an extend-
ed period, the camera may record the burst before
the shutter button is pressed all the way down.
42
Continuous Shooting (Burst Mode/Bracketing)
■ XFILMM SSIMMUULATIION BKT
Each time the shutter button is pressed, the
camera takes three shots at different P FILM
SIMULATION settings (P85): c PROVIA/
STANDARD for the first, d Velvia/VIVID for the
second, and e ASTIA/SOFT for the third.
■ YDYNAMIC RRANGGE BKT
Each time the shutter button is pressed, the cam-
era takes three shots at different U DYNAMIC
RANGE settings (P84): A 100% for the first,
B 200% for the second, and C 400% for
the third (N ISO can not exceed 3200; values less
than 400 are not available when O is selected for
O IMAGE SIZE).
43
d Exposure Compensation
Use exposure compensation when photographing very bright, very dark, or high-contrast subjects.
Rotate the exposure compensation dial.
The effect is visible in the display.
Exposure indicator
Choose negative values Choose positive values to
to reduce exposure
increase exposure
44
Metering
To choose how the camera meters exposure, press the AE button and then choose from the following
options.
Option
o
Description
Automatic scene recognition is used to adjust exposure for a wide range of shooting conditions.
(MULTI)
p
The camera meters lighting conditions at the center of the frame. Recommended when the back-
(SPOT) ground is much brighter or darker than the main subject.
Exposure is set to the average for the entire frame. Provides consistent exposure across multiple
shots with the same lighting, and is particularly effective for landscapes and portraits of subjects
dressed in black or white.
q
(AVERAGE)
45
Focus Mode
Use the focus mode selector to choose how the camera focuses.
The following options are available:
Mode
Description
AF-S
(SINGLE AF)
Focus locks while the shutter button is pressed halfway. Choose for stationary subjects.
The camera continually adjusts focus to reflect changes in the distance to the subject even
when the shutter button is not pressed halfway (note that this increases the drain on the
battery). Choose for moving subjects.
AF-C
(CONTINUOUS AF)
Focus manually using the sub-command dial. Rotate the sub-command dial left to reduce
the focus distance, right to increase. The manual focus indicator indicates how closely the
focus distance matches the distance to the subject in the focus brackets (the red bar indicates
the focus distance, the white bar the depth of field, or in other words the distance in front of
and behind the focus point that appears to be in focus). Choose for manual control of focus
or in situations in which the camera is unable to focus using autofocus (P34). Intelligent
Face Detection turns off automatically.
MF
(MF)
Focus distance
(red bar)
Reduce focus
distance
Increase fo-
cus distance
Manual focus
indicator
Depth of field
(white bar)
Manual focus mode icon
46
Focus Mode
2 Manual Focus
• Use of a tripod is recommended. Focus may be affected if the camera moves.
• Use the I FOCUS CONTROL DIAL option in the setup menu (P103) to reverse the direction of rotation of
the sub-command dial.
• The camera will not focus if the sub-command dial is rotated past infinity.
• To focus using autofocus, press the AFL/AEL button. This can be used to quickly focus on
a chosen subject in manual focus mode.
• The camera can show focus distance in meters or feet. Use the MFOCUS SCALE UNITS
option in the setup menu (P103) to choose the units used.
jFOCUS CHECK
If ON is selected for jFOCUS CHECK in the setup menu (P102),
rotating the sub-command dial magnifies the view in the LCD
monitor.
.
2 Scrolling the focus check area
Press the AF button and then press the selector up, down, left or right to scroll the focus
check area (returned to the center by pressing MENU/OK). The setting takes effect when you
press the AF button again.
47
Focus Frame Selection
When tAREA is selected for FAF MODE in When framing a picture in the LCD monitor, you
the shooting menu and AF-S is selected for focus can choose the size of the focus frame for AF-S.
mode, focus position can be changed. Press AF Press the AF button and then rotate the main-
button and then press the selector up, down, left command dial. The frame size can be reduced up
or right (the focus frame can be returned to the to 50% or enlarged up to 150% (returned to 100%
center by pressing MENU/OK). The setting takes ef- by pressing the main-command dial). The setting
fect when you press the AF button again.
takes effect when you press the AF button again.
Focus point
Focus frame
48
White Balance
For natural colors, press the WB button and choose a setting that matches the light source.
Option
AUTO
h
Description
White balance adjusted automatically.
Measure a value for white balance.
Selecting this option displays a list of color temperatures (P50); highlight a temperature and
press MENU/OK.
k
i
j
k
l
m
n
g
For subjects in direct sunlight.
For subjects in the shade.
Use under “daylight” fluorescent lights.
Use under “warm white” fluorescent lights.
Use under “cool white” fluorescent lights.
Use under incandescent lighting.
Reduces the blue cast typically associated with underwater lighting.
h: Custom White Balance
Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will
be displayed; frame a white object so that it fills the LCD monitor and press the shutter button all the way down
to measure white balance.
• If “COMPLETED!” is displayed, press MENU/OK to set white balance to the measured value.
• If “UNDER” is displayed, raise exposure compensation (P44) and try again.
• If “OVER” is displayed, lower exposure compensation and try again.
1
For greater precision, adjust P FILM SIMULATION, N ISO, and U DYNAMIC RANGE before measuring
white balance.
49
White Balance
1
• White balance is adjusted for flash lighting only in AUTO and g modes. Turn the flash off using other white bal-
ance options.
• Results vary with shooting conditions. Play pictures back after shooting to check colors in the LCD monitor.
k: Color Temperature
Color temperature is an objective measure of the color of a light source, expressed in Kelvin (K). Light sources
with a color temperature close to that of direct sunlight appear white; light sources with a lower color tempera-
ture have a yellow or red cast, while those with a higher color temperature are tinged with blue. You can match
color temperature to the light source as shown in the following table, or choose options that differ sharply from
the color of the light source to make pictures “warmer” or “colder”.
Choose for redder light sources
or “colder” pictures
Choose for bluer light sources
or “warmer” pictures
15,000 K
Blue sky
2,000 K
Candlelight
Sunset/sunrise
5,000 K
Direct sunlight
Shade
50
The Fn Button
The role played by the Fn button can be selected using the FFn
BUTTON option in the setup menu (P101).
The following options are available:
ISO (P82)/IMAGE SIZE (P83)/IMAGE QUALITY (P84)/DYNAMIC RANGE
(P84)/FILM SIMULATION (P85)/AF MODE (P86)/FACE DETECTION (P86)/
FACE RECOGNITION (P87)/INTELLIGENT DIGITAL ZOOM (P86).
51
b Intelligent Face Detection
Intelligent Face Detection allows the camera to automatically detect human faces and set focus and
exposure for a face anywhere in the frame for shots that emphasize portrait subjects. Choose for group
portraits (in horizontal or vertical orientations) to prevent the camera from focusing on the background.
To use Intelligent Face Detec-
tion, press MENU/OK to display
the shooting menu and se-
lect ON for b FACE DETEC-
TION. Faces can be detected
with the camera in vertical
or horizontal orientation; if a
face is detected, it will be indicated by a green bor-
der. If there is more than one face in the frame, the
camera will select the face closest to the center;
other faces are indicated by white borders.
Intelligent Face Detection
Intelligent Face Detection is
recommended when using
the self-timer for group- or
self-portraits (P39).
7
Green border
When a picture taken with Intelligent Face Detection
is displayed, the camera can automatically select faces
for red-eye removal (P 92), playback zoom (P57),
slide shows (P90), image search (P61), image disp.
(P99), printing (P74), and cropping (P93).
3
• In some modes, the camera may set exposure for the
frame as a whole rather than the portrait subject.
• If the subject moves as the shutter button is pressed,
their face may not be in the area indicated by the
green border when the picture is taken.
52
n Face Recognition
1
If an error is displayed, take the photograph again.
The camera can store information on the face
and personal details (name, relationship, and
birth date) of portrait subjects and assign these
subjects priority for Intelligent Face Detection or
display their names and other information during
playback.
Enter face recognition data.
3
Press MENU/OK to display face recognition
data and enter the following information:
• NAME: Enter a name of up to 14 characters
and press MENU/OK.
• BIRTHDAY: Enter the subject’s date of birth
and press MENU/OK.
• CATEGORY: Choose the option that describes
your relationship to the subject and press
MENU/OK.
Adding New Faces
Follow the steps below to add faces to the face
recognition database.
Select REGISTER.
Select REGISTER for n FACE RECOGNI-
TION in the shooting menu.
1
1
1
If you attempt to zoom in on the face of a person in-
dicated by a green border in the face recognition da-
tabase on their birthday, the camera will display their
name and the message “Happy Birthday!”.
To disable face recognition, select OFF.
Take a photograph.
After checking that the
subject is facing the cam-
2
c
Face recognition may not be available depending on
the shooting mode.
era, frame the subject us-
ing the guides and take
the photograph.
53
n Face Recognition
Viewing, Editing, and Deleting Existing Data
Face Recognition
The camera can store up to eight faces. If you attempt
to add a ninth face, a confirmation dialog will be dis-
played; use VIEW & EDIT to make room for new faces
by deleting existing data.
Follow the steps below to view, edit, or delete
face recognition data.
Select VIEW & EDIT for n FACE RECOG-
NITION.
1
When Intelligent Face Detection (P 52) is on and
the frame contains multiple subjects from the face
recognition database, the camera displays the name
of the subject that will be used to set focus and ex-
posure (the subject shown by the green frame). If no
name is entered, the camera will show “---”. Subjects
identified using face recognition but not used to set
focus and exposure are shown by orange frames,
other subjects by white frames.
Select a face.
2
View or edit face recognition data.
3
The name, category, or birth date can be ed-
ited as described in Step 3 of “Adding New
Faces” (P 53). To retake the photo, select
REPLACING IMAGE and shoot a new por-
trait as described above.
3
1
To delete face recognition data for the selected sub-
The camera may fail to identify subjects in the face
recognition database if they are not facing the cam-
era or are only partly in the frame, or if details of the
subjects’ faces or expressions differ markedly from
those in the database.
ject, select ERASE.
54
Taking RAW pictures
The camera can take RAW pictures. RAW pictures
are unprocessed data read from the image sensor.
To take RAW pictures, select j RAW in the setup
menu (P102).
RAW button
Press the RAW button to temporarily change the re-
cording format.
Choose RAW+JPEG or RAW to record RAW pic-
tures. If RAW+JPEG is selected, JPEG copies will
also be recorded. Choose OFF to record pictures
in JPEG format only.
1
• To convert RAW files for display on the camera,
use j RAW CONVERSION in the playback menu
(P91).
• To convert RAW files for display on a computer, use
the supplied RAW File Converter software.
j options
RAW+JPEG
RAW
OFF
RAW button pressed
JPEG
JPEG
RAW+JPEG
Taking a picture or pressing the RAW button again re-
3
• RAW pictures cannot be recorded to internal memo-
ry. Insert a memory card.
• Crop, resize, and red-eye removal options are not
available with RAW images during playback. The
maximum zoom available when viewing RAW im-
ages is 3.2×.
stores the previous setting.
Creating JPEG Copies of RAW Pictures
Pressing the RAW button during playback displays
RAW conversion options (P91).
55
Playback Options
To view the most recent picture in the monitor,
press the a button.
Continuous Shooting
In the case of pictures taken in continuous shoot-
ing mode, only the first frame of each series will
be displayed. Press the selector down to view the
other pictures in the series.
I Favorites: Rating Pictures
Press the selector right to view pictures
in the order recorded, left to view pic-
tures in reverse order. Keep the selector
pressed to scroll rapidly to the desired
frame.
To rate the picture currently displayed in full-frame
playback, press DISP/BACK and press the selector
up and down to select from zero to five stars.
1
Pictures taken using other cameras are indicated by a m (“gift image”) icon during playback.
56
Playback Options
Playback Zoom
Intelligent Face Detection
Pictures taken with Intelligent Face Detection (P52)
are indicated by a g icon. Press the f button to
zoom in on the subject selected with Intelligent Face
Detection. You can then use the k and n buttons
to zoom in and out.
Press k to zoom in on pictures displayed in sin-
gle-frame playback; n to zoom out. When the
picture is zoomed in, the selector can be used to
view areas of the image not currently visible in the
display.
Zoom indicator
Navigation window
shows portion of image
currently displayed in
monitor
Press DISP/BACK or MENU/OK to exit zoom.
1
The maximum zoom ratio varies with image size. Play-
back zoom is not available with cropped or resized
copies saved at a size of a or smaller.
57
Playback Options
Multi-Frame Playback
To change the number of images displayed, press Use the selector to highlight images and press
n in single-frame view.
MENU/OK to view the highlighted image full frame.
In the nine- and hundred-frame displays, press
the selector up or down to view more pictures.
2 Two-Frame Display
Two-frame display can be used
to compare pictures taken in
C mode.
Press k to view
fewer images.
Press n to view
more images.
58
A Deleting Pictures
To delete individual pictures, multiple selected pictures, or all pictures,
press MENU/OK, select A ERASE (P89), and choose from the options
below. Note that deleted pictures can not be recovered. Copy important
pictures to a computer or other storage device before proceeding.
Option
Description
Press the selector left or right to scroll through pictures and press MENU/OK to delete the current
picture (a confirmation dialog is not displayed).
FRAME
Highlight pictures and press MENU/OK to select or deselect (pictures included in the photobook
or print order are shown by S). When the operation is complete, press DISP/BACK to display a
confirmation dialog, then highlight OK and press MENU/OK to delete the selected pictures.
A confirmation dialog will be displayed; highlight OK and press MENU/OK to delete all unpro-
tected pictures (if a memory card is inserted, only the pictures on the memory card will be af-
fected; the pictures in internal memory are only deleted if no memory card is inserted). Pressing
DISP/BACK cancels deletion; note that any pictures deleted before the button was pressed can
not be recovered.
SELECT FRAMES
ALL FRAMES
1
• Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (P92).
• If a message appears stating that the selected images are part of a DPOF print order, press MENU/OK to delete the
pictures.
59
Viewing Photo Information
Photo information can be viewed by pressing DISP/BACK to cycle through indicators (P7) until the fol-
lowing display appears:
Additional photo information
Additional photo information
can be viewed by rotating the
main-command dial. Rotate the
main-command dial to cycle the
display.
a
The active focus point is shown by a“+”icon.
Zooming in on the Focus Point
Press the main-command dial
to zoom in on the focus point.
Press the main-command dial
again to return to full-frame
playback.
Dynamic range
Sensitivity
Film simulation
Exposure compensation
Picture (overexposed areas blink on and off )
Histogram
Image size and quality
Shutter speed/aperture
q
e
t
i
!
!
w
r
y
Flash mode
White balance
u
Frame number
o
60
Image Search
Search for images by various criteria.
Select bIMAGE SEARCH in the playback
menu (P89), highlight one of the following
search criteria, and press MENU/OK:
Select a search condition. Only pictures that
match the search condition will be displayed.
To delete or protect selected pictures or to
view the selected pictures in a slide show,
press MENU/OK and choose from the following
options:
1
2
Option
Description
Find all pictures taken on a selected
date.
BY DATE
Find all pictures based on specified face
information.
BY FACE
Option
See page
59
AERASE
Find all pictures with a specified rating
(P56).
Find all pictures that match a selected
scene.
BY I FAVORITES
BY SCENE
DPROTECT
92
ISLIDE SHOW
90
Find all still pictures, all movies, all pic-
BY TYPE OF DATA tures taken in burst mode, or all RAW
pictures.
Find all pictures selected for upload to a
specified destination (P89).
BY UPLOAD MARK
61
X PhotoBook Assist
Create books from your favorite photos.
Creating a PhotoBook
Scroll through the images and press the selec-
tor up to select or deselect the current image
for inclusion in the book. To display the current
image on the cover, press the selector down.
Select X PHOTOBOOK ASSIST in the play-
back menu.
5
1
Highlight NEW BOOK.
2
1
The first picture selected automatically becomes
the cover image. Press the selector down to select
a different picture for the cover.
Press MENU/OK to display the new
book dialog.
3
Choose pictures for the new book.
• SELECT FROM ALL: Choose from all the
pictures available.
• SELECT BY IMAGE SEARCH: Choose from pictures
matching selected search conditions (P61).
Press MENU/OK to exit when the book
is complete.
4
6
7
Highlight COMPLETE PHOTOBOOK.
1
Neither photographs a or smaller nor movies can
be selected for photobooks.
1
Choose SELECT ALL to select all photos, or all pho-
tos matching the specified search conditions, for
the book.
62
k PhotoBook Assist
Press MENU/OK. The new book will be
added to the list in the photobook
assist menu.
Viewing PhotoBooks
8
Highlight a book in the photobook assist menu
and press MENU/OK to display the book, then press
the selector left and right to scroll through the
pictures. Press DISP/BACK to return to the photo-
book assist menu.
3
• Photobooks can contain up to 300 pictures.
• Books that contain no photos are automatically
deleted.
Editing and Deleting PhotoBooks
PhotoBooks
Photobooks can be copied to a computer using the
supplied MyFinePix Studio software.
Display the photobook and press
1
MENU/OK to view book edit options.
Choose from the following options:
• EDIT: Edit the book as described in “Creating a
PhotoBook” on page 62.
2
• ERASE: Delete the current photobook.
Follow the on-screen instructions.
3
63
Viewing Panoramas
If you press the selector down when a panorama is displayed full frame, the camera will play back the
picture from left to right or from bottom to top.
PAUSE
The following operations can be performed during playback:
Opperaattiion
Button
Description
Start/pause
playback
Press the selector down to start playback. Press again to pause.
End playback
Press the selector up to end playback.
1
• Once displayed in full-frame playback, panoramas can be zoomed in or out using the zoom buttons.
• zpanoramas play back in an endless loop (P31); the playback direction can be controlled by pressing the
selector left or right. The camera will not turn off automatically while playback is in progress (P101).
64
Recording Movies
Shoot short movies with sound. During recording, R and the time remaining will be displayed in
the LCD monitor and sound will be recorded via the built-in microphone (be careful not to cover the
microphone during recording).
98
18m39s
Number of photos that
can be taken during
recording
Time remaining
Rotate the mode dial to FMOVIE.
1
Press the shutter button all the way down to start recording.
2
To end recording, press the shutter button again. Recording ends automatically when the
movie reaches maximum length or memory is full.
3
1
• Zoom can be adjusted while recording is in progress.
• If the subject is poorly lit, the AF-assist lamp may light to assist the focus operation.
To turn the AF-assist lamp off , select OFF for C AF ILLUMINATOR in the setup menu (P102).
• Focus, exposure, and white balance are adjusted automatically throughout recording. The color and brightness
of the image may vary from that displayed before recording begins.
• Sounds made by the camera may be recorded.
65
Recording Movies
Movie Frame Size
Before recording, select a frame size using the
W MOVIE MODE option in the shooting menu
(P88).
Taking Photographs During Recording
Press MENU/OK to take a photograph during record-
ing.
1
• If O is selected for O IMAGE SIZE, the picture
will be recorded at size P.
• The photo is saved separately from the movie and
does not appear as part of the movie.
Option
Description
i 1920 (1920 × 1080) Full HD (High Definition).
h 1280 (1280 × 720) High Definition.
f (640 × 480)
Standard definition.
3
• Photos can not be taken while a high-speed movie
is being recorded.
High speed movie. Sound is not
recorded, and focus, exposure, and
white balance are not adjusted au-
tomatically. Black bands appear at
the top and bottom of movies re-
corded at Y 320 × 112.
Y 640 × 480 (70fps)
Y 320 × 240 (120fps)
• The number of photos that can be taken is limited.
3
Y 320 × 112 (200fps)
• The indicator lamp lights while movies are being re-
corded. Do not open the battery chamber during
shooting or while the indicator lamp is lit. Failure
to observe this precaution could prevent the movie
from being played back.
• Vertical or horizontal streaks may appear in movies
containing very bright subjects. This is normal and
does not indicate a malfunction.
• The temperature of the camera may rise if it is used to
record movies for an extended period or if the ambi-
ent temperature is high. This is normal and does not
indicate a malfunction.
66
a Viewing Movies
During playback (P 56),
movies are displayed in the
monitor as shown at right.
The following operations
can be performed while a
movie is displayed:
Playback Speed
Arrow
Press the selector left or right to
adjust playback speed. Speed is
shown by the number of arrows
(M or N).
Opperaattiion
Description
Press the selector down to start playback.
2 Viewing Movies on a Computer
Copy movies to the computer before viewing.
Start/ Press again to pause. While playback is
pause paused, you can press the selector left or
playback right to rewind or advance one frame at
a time.
3
Do not cover the speaker during playback.
End
playback/ Press the selector up to end playback.
delete
Adjust Press the selector left or right to adjust play-
speed back speed during playback.
Press MENU/OK to pause playback and dis-
play volume controls. Press the selector
Adjust
up or down to adjust the volume and
volume
press MENU/OK to exit. Volume can also be
adjusted from the setup menu.
67
Viewing Pictures on TV
Connect the camera to a TV to show pictures to a group.
Turn the camera off.
1
2
Connect the A/V cable (optional) or HDMI cable (available from third-party suppliers).
Insert into USB
connector
Connect white plug
to audio-in jack
Connect yellow plug
to video-in jack
Insert into HDMI
connector
Insert into HDMI
connector
HDMI Mini Connector
68
Viewing Pictures on TV
HDMI
An HDMI cable (available from third-party suppliers; P106) can be used to connect the camera to High
Definition (HD) devices (playback only). The USB cable or optional A/V cable cannot be used while an HDMI
cable is connected.
Tune the television to the video or HDMI input channel. See the documentation supplied with the
television for details.
3
4
Press the a button for about a second to turn the camera on. The camera monitor turns off and
pictures and movies are played back on the TV. Note that the camera volume controls have no ef-
fect on sounds played on the TV; use the television volume controls to adjust the volume.
1
Image quality drops during movie playback.
3
When connecting the cable, be sure the connectors are fully inserted.
69
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without first being copied to a computer. Note that depending on
the printer, not all the functions described below may be supported.
Connecting the Camera
Printing Selected Pictures
Connect the supplied USB cable as shown and
Press the selector left or right to display a pic-
1
1
turn the printer on.
ture you wish to print.
Press the selector up or down to choose the
number of copies (up to 99).
2
Repeat steps 1–2 to select additional pictures.
Press MENU/OK to display a confirmation dialog
when settings are complete.
3
Press the a button for about a second to turn
2
PRINT THESE FRAMES
the camera on. t USB will be displayed in
the monitor, followed by the PictBridge display
shown below at right.
TOTAL:
9
SHEETS
YES
CANCEL
USB
Press MENU/OK to start printing.
4
SET
70
Printing Pictures via USB
2 Printing the Date of Recording
Printing the DPOF Print Order
To print the print order created with K PRINT
ORDER (DPOF) in the playback menu (P95):
To print the date of recording on pictures, press DISP/
BACK in steps 1–2 to display the PictBridge menu (see
“Printing the DPOF Print Order,” below). Press the se-
lector up or down to highlight PRINT WITH DATE s
and press MENU/OK to return to the PictBridge display
(to print pictures without the date of recording, select
PRINT WITHOUT DATE).
In the PictBridge display, press DISP/BACK to
open the PictBridge menu.
1
PICTBRIDGE
PRINT WITH DATE
PRINT WITHOUT DATE
PRINT DPOF
1
If no pictures are selected when the MENU/OK button is
pressed, the camera will print one copy of the current
picture.
Press the selector up or down to highlight
u PRINT DPOF.
2
Press MENU/OK to display a confirmation dialog.
3
TOTAL:
9
SHEETS
YES
CANCEL
71
Printing Pictures via USB
1
Press MENU/OK to start printing.
4
• Pictures can be printed from internal memory or a
memory card that has been formatted in the cam-
era.
• If the printer does not support date printing, the
PRINT WITH DATE s option will not be available in
the PictBridge menu and the date will not be printed
on the pictures in the DPOF print order.
• When pictures are printed via direct USB connection,
page size, print quality, and border selections are
made using the printer.
During Printing
The message shown at right
is displayed during printing.
Press DISP/BACK to cancel be-
fore all pictures are printed
(depending on the printer,
printing may end before the
current picture has printed).
PRINTING
CANCEL
If printing is interrupted, turn the camera off and then
on again.
Disconnecting the Camera
Confirm that “PRINTING” is not displayed in the moni-
tor and turn the camera off. Disconnect the USB
cable.
72
Printing Pictures via USB
Creating a DPOF Print Order
The K PRINT ORDER (DPOF) option in the play-
back menu can be used to create a digital “print
order” for PictBridge-compatible printers (P106)
or devices that support DPOF.
■ WITH DATE s/ WITHOUT DATE
Select playback mode and press MENU/OK to
display the playback menu.
1
2
3
Highlight K PRINT ORDER (DPOF) and press
MENU/OK.
DPOF
DPOF (Digital Print Order Format) is a stan-
dard that allows pictures to be printed from
“print orders” stored in internal memory or
on a memory card. The information in the
order includes the pictures to be printed, date im-
print, and the number of copies of each picture.
Highlight one of the following options and
press MENU/OK:
• WITH DATE s: Print the date of recording on
pictures.
• WITHOUT DATE: Do not print the date of record-
ing on pictures.
Press the selector left or right to display a pic-
ture you wish to include in or remove from the
print order.
4
73
Printing Pictures via USB
Press the selector up or down to choose the
number of copies (up to 99). To remove a pic-
ture from the order, press the selector down
until the number of copies is 0.
Repeat steps 4–5 to complete the print order.
Press MENU/OK to save the print order when set-
tings are complete, or DISP/BACK to exit without
changing the print order.
5
6
7
The total number of prints is displayed in the
monitor. Press MENU/OK to exit.
Total number of prints
Number of copies
The pictures in the current
print order are indicated by a
u icon during playback.
2 Intelligent Face Detection
If the current picture was created with Intelligent
Face Detection, pressing fsets the number of cop-
ies to the number of faces detected.
1
When pictures are printed via direct USB connec-
tion, page size, print quality, and border selections
are made using the printer.
74
Printing Pictures via USB
1
■ RESET ALL
• Remove the memory card to create or modify a print
order for the pictures in internal memory.
• Print orders can contain a maximum of 999 pictures.
• If a memory card is inserted
containing a print order cre-
ated by another camera, the
message shown at right will
be displayed. Pressing MENU/
OK cancels the print order; a
To cancel the current print
order, select RESET ALL
in the K PRINT ORDER
(DPOF) menu. The confir-
mation shown at right will
YES
CANCEL
be displayed; press MENU/OK to remove all pictures
from the order.
YES
NO
new print order must be created as described above.
75
Viewing Pictures on a Computer
The supplied software can be used to copy pictures to a computer, where they can be stored, viewed,
organized, and printed. Before proceeding, install the software as described below. Do NOT connect the
camera to the computer until installation is complete.
Installing the Software
Two applications are supplied: MyFinePix Studio for Windows and FinePixViewer for the Macintosh.
Installation instructions for Windows are on pages 76–77, those for the Macintosh on pages 78–79.
Winddoowwss:: IInnssttaalllliinngg MMyFFiinneePPiixx Studdiioo
Confirm that the computer meets the following system requirements:
1
Windows 7 (SP 1)/Windows Vista (SP 2) 1
3GHz Pentium 4 or better
Windows XP (SP 3) 1
2GHz Pentium 4 or better
(2.4GHz Core 2 Duo or better)2
512MB or more
CPU
(2.4GHz Core 2 Duo or better)2
RAM
Free disk space
GPU
1GB or more
(1GB or more)2
2GB or more
Supports DirectX 9 or later
Supports DirectX 7 or later
(recommended)
(required; performance not guaranteed with other GPUs)
Video
1,024×768 pixels or more with 24-bit color or better
• Built-in USB port recommended. Operation is not guaranteed with other USB ports.
Other
• Internet connection (broadband recommended) required to install .NET Framework (if necessary), to use
auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.
1 Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not
guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.
2 Recommended when displaying HD movies.
76
Viewing Pictures on a Computer
Start the computer. Log in to an account with administrator privileges before proceeding.
2
3
Exit any applications that may be running and insert the installer CD in a CD-ROM drive.
Windows 7/Windows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;
click Yes (Windows 7) or Allow (Windows Vista).
The installer will start automatically; click Install MyFinePix Studio and follow the on-screen in-
structions to install MyFinePix Studio.
If the Installer Does Not Start Automatically
If the installer does not start automatically, select Computer or My Computer from the Start menu, then
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click setup or SETUP.EXE.
If prompted to install Windows Media Player, DirectX, or .NET Framework, follow the on-screen in-
structions to complete installation.
4
5
Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer
CD in a dry location out of direct sunlight in case you need to re-install the software. The version
number is printed at the top of the CD label for reference when updating the software or contacting
customer support.
Installation is now complete. Proceed to “Connecting the Camera” on page 80.
77
Viewing Pictures on a Computer
Maciinntosh: Innsttaalllliinngg FinePixViieewer
Confirm that the computer meets the following system requirements:
1
CPU
PowerPC or Intel (Core 2 Duo or better)*
Pre-installed versions of Mac OS X version 10.3.9–10.6
(visit http://www.fujifilm.com/support/digital_cameras/compatibility/ for more information)
OS
RAM
256MB or more (1GB or more)*
Free disk space A minimum of 200MB required for installation with 400MB available when FinePixViewer is running
Video
Other
800×600 pixels or more with thousands of colors or better
Built-in USB port recommended. Operation is not guaranteed with other USB ports.
* Recommended when displaying HD movies.
After starting the computer and quitting any applications that may be running, insert the installer
CD in a CD-ROM drive and double-click Installer for Mac OS X.
2
3
1
To install RAW FILE CONVERTER, double-click SILKYRFCEXInstaller. RAW FILE CONVERTER is used to view
RAW images on your computer.
An installer dialog will be displayed; click Installing FinePixViewer to start installation. Enter an
administrator name and password when prompted and click OK, then follow the on-screen instruc-
tions to install FinePixViewer. Click Exit to quit the installer when installation is complete.
78
Viewing Pictures on a Computer
Remove the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD
if Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry
location out of direct sunlight in case you need to re-install the software. The version number is
printed at the top of the CD label for reference when updating the software or contacting customer
support.
4
5
Mac OS X 10.5 or earlier: Open the “Applications” folder, start Image Capture, and select Preferences…
from the Image Capture application menu. The Image Capture preferences dialog will be displayed;
choose Other… in the When a camera is connected, open menu, then select FPVBridge in the
“Applications/FinePixViewer” folder and click Open. Quit Image Capture.
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start Image
Capture. The camera will be listed under DEVICES; select the camera and choose FPVBridge from
the Connecting this camera opens menu and click Choose. Quit Image Capture.
Installation is now complete. Proceed to “Connecting the Camera” on page 80.
79
Viewing Pictures on a Computer
Connecting the Camera
If the pictures you wish to copy are stored on a
memory card, insert the card into the camera
(P11).
Press the a button for about a second to
turn the camera on. MyFinePix Studio or
FinePixViewer will start automatically; follow
the on-screen instructions to copy pictures to
the computer. To exit without copying pic-
tures, click Cancel.
1
3
1
Windows users may require the Windows CD when
starting the software for the first time.
3
3
If the software does not start automatically, it may
not be correctly installed. Disconnect the camera
and reinstall the software.
Loss of power during transfer could result in loss of
data or damage to internal memory or the memory
card. Charge the battery before connecting the
camera.
For more information on using the supplied soft-
ware, start the application and select the appro-
priate option from the Help menu.
Turn the camera off and connect the supplied
2
USB cable as shown, making sure the connec-
tors are fully inserted. Connect the camera di-
rectly to the computer; do not use a USB hub
or keyboard.
80
Viewing Pictures on a Computer
3
Disconnecting the Camera
• If a memory card containing a large number of images
is inserted, there may be a delay before the software
starts and you may be unable to import or save im-
ages. Use a memory card reader to transfer pictures.
• Make sure that the computer does not display a mes-
sage stating that copying is in progress and that the
indicator lamp is out before turning the camera off or
disconnecting the USB cable (if the number of imag-
es copied is very large, the indicator lamp may remain
lit after the message has cleared from the computer
display). Failure to observe this precaution could re-
sult in loss of data or damage to internal memory or
the memory card.
After confirming that the indicator lamp is out, follow
the on-screen instructions to turn the camera off and
disconnect the USB cable.
Uninstalling the Supplied Software
Only uninstall the supplied software when it is no lon-
ger required or before beginning reinstallation. After
quitting the software and disconnecting the camera,
drag the “FinePixViewer” folder from “Applications”
into the Trash and select Empty Trash in the Finder
menu (Macintosh), or open the control panel and use
“Programs and Features” (Windows 7/Windows Vista)
or “Add or Remove Programs” (Windows XP) to unin-
stall MyFinePix Studio. Under Windows, one or more
confirmation dialogs may be displayed; read the con-
tents carefully before clicking OK.
• Disconnect the camera before inserting or removing
memory cards.
• In some cases, it may not be possible to access pictures
saved to a network server using the supplied software
in the same way as on a standalone computer.
• The user bears all applicable fees charged by the
phone company or Internet service provider when
using services that require an Internet connection.
81
Using the Menus: Shooting Mode
Use the shooting menus to adjust shooting set-
tings. The options available vary with the shoot-
ing mode selected.
Shooting Menu Options
Default values are shown in square brackets [ ].
A E MODE
Choose an option for E mode (P28).
[R]
Using the Shooting Menu
Press MENU/OK to display the shoot-
ing menu.
1
A Adv. MODE
[r]
Choose an advanced shooting mode (P29).
SCENE POSITION
Choose a scene for SP mode (P33).
N ISO [AUTO (800)]
Control the camera’s sensitivity to light.
Press the selector up or down to
highlight the desired menu item.
2
A
[L]
Press the selector right to display op-
tions for the highlighted item.
3
Press the selector up or down to
highlight the desired option.
Option
Description
4
Sensitivity is adjusted auto-
matically in response to shoot-
ing conditions.
As above, except that sensitiv-
ity will not be raised above the
value in parentheses.
AUTO
Press MENU/OK to select the high-
lighted option.
5
AUTO (3200) / AUTO (1600) /
AUTO (800) / AUTO (400)
Press DISP/BACK to exit from the
menu.
6
12800 / 6400 / 5000 /
4000 / 3200 / 2500 /
2000 / 1600 / 1250 /
1000 / 800 / 640 / 500 /
400 / 320 / 250 / 200 / 100
Sensitivity is set to the speci-
fied value, which is shown in
the display.
82
Using the Menus: Shooting Mode
Size Versus Aspect Ratio
ISO
Higher values can reduce blur; note, however, that
mottling may appear in pictures taken at high sen-
sitivities.
Size
Option
O
Prints at sizzes up too
34×25cm (13.5×10 in.)
24×18 cm (9.5×7 in.)
17×13 cm (7 × 5 in.)
100
12800
ISO
P
Bright
Less
noticeable
Dark
More
noticeable
Scene
Noise
(mottling)
Q
Aspect ratio
4 : 3: Pictures have the same proportions as the camera
display.
3 : 2: Pictures have the same proportions as a frame of
35 mm film.
O IMAGE SIZE
[O 4 : 3]
O 4 : 3
Choose the image size and
aspect ratio at which pictures
are recorded. Large pictures
Size
Aspect ratio
16 : 9: Suited for display on High Definition (HD) de-
can be printed at large sizes with no drop in qual-
ity, while small pictures require less memory, al-
lowing more pictures to be recorded.
vices.
1 : 1: Pictures are square.
83
Using the Menus: Shooting Mode
T IMAGE QUALITY
Choose how much image files are compressed.
[FINE]
Option
A 100%
Description
Increase contrast when shooting
indoors or under overcast skies.
AUTO B 200%
C 4000%
Option
FINE
Description
Low compression. Select for higher image
quality.
Reduce loss of detail in highlights
and shadows when photograph-
ing high-contrast scenes.
D 800%
High compression. Select this option to
store more pictures.
NORMAL
M 1600%
U DYNAMIC RANGE
[AUTO]
1
M 1600% and D 800% are available only when
D-RANGE PRIORITY is selected in E mode.
Control contrast. Higher values are recommend-
ed for scenes that include both sunlight and deep
shade or for increased contrast with such subjects
as sunlight on water, brightly-lit autumn leaves,
portraits taken against a blue sky, and white ob-
jects or people wearing white; note, however, that
mottling may appear in pictures taken at higher
values. If AUTO is selected, the camera will auto-
matically select values between 100% and 400%
in response to shooting conditions.
84
Using the Menus: Shooting Mode
P FILM SIMULATION
[c] d WB SHIFT
Simulate the effects of different types of film, in- White balance can be fine-tuned. Adjust the se-
cluding sepia and black-and-white.
lected color axis (R–Cy=Red-Cyan or B-Ye=Blue–
Yellow) by +3 to –3 in increments of one.
Option
Description
Standard color reproduction. Suited to a
wide range of subjects, from portraits to
landscapes.
f COLOR
Adjust color density.
[MID]
c (PROVIAA/
STANDARD)
d (Velvia/ A high-contrast palette of saturated col-
VIVID)
ors, suited to nature photographs.
e (ASTIA/ A soft-toned palette of less saturated col-
H SHARPNESS
Choose whether to sharpen or soften outlines.
[STD]
SOFT)
b (MONO-
CHROME)
ors.
r HIGHLIGHT TONE
Adjust the appearance of highlights.
[STD]
Take pictures in black and white.
Take black-and-white pictures with
slightly increased contrast. This setting
also slightly tones down the brightness
of the sky.
s SHADOW TONE
Adjust the appearance of shadows.
[STD]
[STD]
e (MONO-
CHROME +
Ye FILTER)
h NOISE REDUCTION
Choose the amount of noise reduction.
d (MONO- Take black-and-white pictures with in-
CHROME +
R FILTER)
creased contrast. This setting also tones
down the brightness of the sky.
f (MONO-
CHROME +
G FILTER)
Soften skin tones in black-and-white por-
traits.
f (SEPIA) Take pictures in sepia.
85
Using the Menus: Shooting Mode
R INTELLIGENT DIGITAL ZOOM
[OFF] F AF MODE
[t]
If ON is selected, intelligent digital zoom magni- Choose how the camera selects the focus area
fies the image to 2× while processing it for sharp, when in AF-S focus mode (P46). Note that re-
high-resolution results.
gardless of the option selected, the camera will
focus on the subject in the center of the monitor
when macro mode is on (P36).
• s MULTI: When the shutter button is pressed
halfway, the camera detects high-contrast sub-
jects near the center of the frame and selects
the focus area automatically.
• t AREA: Choose the focus area manually
(P48).
• x TRACKING: Position the subject in the fo-
cus target and press the selector left. The cam-
era will track the subject and adjust focus as it
moves through the frame.
a
• Intelligent digital zoom may end when another mode
is selected.
• Intelligent digital zoom may sometimes produce low-
er quality images than optical zoom.
• The time needed to record images increases.
• The effects are not visible in the display during shoot-
ing.
• Intelligent digital zoom is not available in continuous
mode or during movie recording.
Z ADVANCED ANTI BLUR
Select ON to enable advanced anti blur in R
[ON]
mode (P29).
1
Note that in x mode, the camera focuses continu-
ously, increasing the drain on the battery, and that the
sound of the camera focusing may be audible.
b FACE DETECTION
Choose whether the camera automatically de-
tects and sets focus and exposure for human por-
trait subjects (P52).
86
Using the Menus: Shooting Mode
c
• The flash may not fully light the subject at speeds
n FACE RECOGNITION
Add portrait subjects to the face recognition da-
tabase. These subjects will be given priority dur-
ing Intelligent Face Detection, and their names
and other information can be viewed during play-
back (P53).
faster than 1 1000 s.
/
• Use auto or custom white balance (P49).
• If the built-in flash is raised when ON is selected for
g EXTERNAL FLASH, the built-in flash will fire once
to provide a signal for the optional flash unit to fire.
• External flash units can be used in P, S, A, M or EXR
(S and T only) modes.
I FLASH
[ 0]
Adjust flash brightness. Choose from values be-
• Fujifilm external flash units do not require this set-
ting.
2
2
/
/
tween + 3 EV and – 3 EV. The default setting is 0.
Note that the desired results may not be achieved
depending on shooting conditions and the dis-
tance to the subject.
a
• The camera can be used with flash units that provide
aperture adjustment, external metering, and sensitiv-
ity control. Some flash units that are designed spe-
cifically for other cameras can not be used.
• For information on Fujifilm external flash units, see
Accessories from FUJIFILM (P107).
g EXTERNAL FLASH
[OFF]
Choose ON when using an optional flash unit (ex-
cept Fujifilm products) mounted on the camera
hot shoe.
K CUSTOM SET
Save settings for P, S, A, M and all EXR modes ex-
cept R (P27).
87
Using the Menus: Shooting Mode
v DISP. CUSTOM SETTING
W MOVIE MODE
[i]
Choose the items displayed in the LCD monitor Choose a frame size for movies (P66).
(P6). The following items can be displayed:
F AF MODE (F mode)
This option controls how the camera selects the
focus area for movies.
[u]
FRAMING GUIDLINE*
AF DISTANCE INDICATOR
WHITE BALANCE
HISTOGRAM
IMAGE SIZE/QUALITY
PHOTOMETRY
ELECTRONIC LEVEL
MF DISTANCE INDICATOR
APERTURE/S-SPEED/ISO
FRAMES REMAINING
BATTERY LEVEL
Option
Description
The camera focuses on the subject in
the center of the frame.
r CENTER
FLASH
FILM SIMULATION
EXP. COMPENSATION
DYNAMIC RANGE
The camera continuously adjusts fo-
u CONTIINUOUS cus to reflect changes in the distance
to the subject in the focus frame.
* You can also select the grid type (P103).
See pages 5 – 6 for the locations of these items in
the displays.
1
Note that in u mode, the camera focuses continu-
ously, increasing the drain on the battery, and that the
sound of the camera focusing may be audible.
Virtual Horizon
Selecting ELECTRONIC LEVEL
displays a virtual horizon. The
camera is level when the two
lines overlap.
1
The virtual horizon may not be displayed if the cam-
era lens is pointed up or down.
88
Using the Menus: Playback Mode
Using the Playback Menu
Playback Menu Options
Press the a button to enter play-
back mode.
1
X PHOTOBOOK ASSIST
Create books from your favorite photos (P62).
Press MENU/OK to display the play-
back menu.
2
bIMAGE SEARCH
Search for pictures (P61).
Press the selector up or down to
highlight the desired menu item.
3
xERASE
Delete all or selected pictures (P59).
Press the selector right to display op-
tions for the highlighted item.
jMARK FOR UPLOAD TO
Select pictures for upload to YouTube or Facebook
using MyFinePix Studio (Windows only).
4
Press the selector up or down to
highlight the desired option.
5
■ Selecting PPiicttuurrees for Upload
Select YouTube to choose movies for upload
to YouTube, FACEBOOK to choose photos and
movies for upload to Facebook.
1
Press MENU/OK to select the high-
lighted option.
6
Press the selector left or right to display pic-
Press DISP/BACK to exit from the
menu.
2
7
tures and press MENU/OK to select or deselect.
Press DISP/BACK to exit when all the desired pic-
tures are selected.
89
Using the Menus: Playback Mode
1
ISLIDE SHOW
[MULTIPLE]
• Only movies can be selected for upload to YouTube.
• During playback, selected pictures are indicated by
jYouTube or jFACEBOOK icons.
View pictures in an automated slide show. Choose
the type of show and press MENU/OK to start.
Press DISP/BACK at any time during the show to
view on-screen help. The show can be ended at
any time by pressing MENU/OK.
■ RESEETT ALLLL:: DDeesseelleeccttiinngg All Pictures
Choose RESET ALL to deselect all pictures. If the
number of pictures affected is very large, a mes-
sage will be displayed while the operation is in
progress. Press DISP/BACK to exit before the opera-
tion is complete.
Option
Description
Press selector left or right to go back or
skip ahead one frame. Select FADE-IN
for fade transitions between frames.
As above, except that camera automati-
cally zooms in on faces selected with In-
telligent Face detection.
NORMAL
FADE-IN
NORMAL g
■ Uploadinng Picturees (Windoows Only)
Selected pictures can be uploaded using the
YouTube/Facebook Upload option in MyFinePix
Studio.
FADE-IN g
MULLTTIIPPLE
1
Display several pictures at once.
The camera will not turn off automatically while a slide
show is in progress.
Select with camera
Upload from computer
For information on installing MyFinePix Studio
and connecting the camera to a computer, see
“Viewing Pictures on a Computer” (P76).
90
Using the Menus: Playback Mode
j RAW CONVERSION
Setting
Description
Create a JPEG copy using the set-
tings in effect at the time the photo
was taken.
Create JPEG copies of RAW pictures (P55). The
original image data are unaffected, allowing a
single RAW image to be processed in a multitude
of different ways.
REFLECCTT SSHHOOOOTTINNG
COND.
PUSSHH/PULL
PROCESSING
Adjust exposure by –1 EV to +3 EV in
/
increments of 1 3EV (P44).
Enhance details in highlights for
natural contrast (P84).
Simulate the effects of different
types of film (P85).
Adjust white balance (P49).
Fine-tune white balance (P85).
Adjust color density (P85).
Sharpen or soften outlines (P85).
Process the copy to reduce mot-
tling (P85).
Select j RAW CONVER-
SION in the playback menu.
DYYNNAMMICC RANGE
FILM SIMUULATIOON
1
WHITE BAALLAANNCCE
WB SHIFT
COLOR
Press the selector up or down to highlight a
setting and press the selector right to select.
Press the selector up or down to highlight the
desired option and press MENU/OK to select and
return to the settings list. Repeat this step to
adjust additional settings.
2
3
SHAARPNESS
NOISSEE RREEDDUUCCTTIION
HIGHLIGGHHT TOONE
SHADOOW TTOONE
Adjust highlights (P85).
Adjust shadows (P85).
Choose the color space used for
color reproduction (P104).
Press the RAW button to
preview the JPEG copy.
Press MENU/OK to save the
copy or press DISP/BACK to
COOLLOORR SSPACE
return to Step 2.
91
Using the Menus: Playback Mode
BRED EYE REMOVAL
DPROTECT
If the current picture is marked with a g icon to Protect pictures from accidental deletion.
indicate that it was taken with Intelligent Face De-
tection, this option can be used to remove red-
eye. The camera will analyze the image; if red-eye
is detected, the image will be processed to create
a copy with reduced red-eye.
Select DPROTECT in the playback menu.
1
2
Highlight one of the following options and
press MENU/OK:
• FRAME: Protect selected pictures. Press the se-
lector left or right to view pictures and press
MENU/OK to select or deselect. Press DISP/BACK
when the operation is complete.
• SET ALL: Protect all pictures.
Display the desired picture.
1
2
Select BRED EYE REMOVAL in the playback
menu.
• RESET ALL: Remove protection from all pic-
tures.
Press MENU/OK.
3
1
3
Protected pictures will be deleted when the memory
card or internal memory is formatted (P99).
• Red-eye may not be removed if the camera is unable
to detect a face or the face is in profile. Results may
differ depending on the scene. Red-eye can not be
removed from pictures that have already been pro-
cessed using red-eye removal or pictures created
with other devices.
• The amount of time needed to process the image
varies with the number of faces detected.
• Copies created with BRED EYE REMOVAL are indi-
cated by a eicon during playback.
92
Using the Menus: Playback Mode
GCROP
ORESIZE
Create a cropped copy of the current picture.
Create a small copy of the current picture.
Display the desired picture.
Display the desired picture.
1
1
Select GCROP in the playback menu.
Select ORESIZE in the playback menu.
2
2
Use the k and n buttons to zoom the image
in and out and use the selector to scroll the
picture until the desired portion is displayed.
Highlight a size and press MENU/OK to display a
confirmation dialog.
3
3
Press MENU/OK to save the resized copy to a
separate file.
4
1
Press MENU/OK to display a confirmation dialog.
4
5
1
Press MENU/OK again to save the cropped copy
to a separate file.
The sizes available vary with the size of the original im-
age.
Larger crops produce larger copies; all copies have an
aspect ratio of 4:3. If the size of the final copy will be
a, OK will be displayed in yellow.
b Intelligent Face Detection
If the picture was shot with Intelligent Face Detection
(P52), g will be displayed in the monitor. Press the
fbutton to zoom in on the selected face.
93
Using the Menus: Playback Mode
CIMAGE ROTATE
ECOPY
Rotate pictures taken in tall orientation so that Copy pictures from internal memory to a memory
they are displayed in tall orientation in the LCD card.
monitor.
Select ECOPY in the playback menu.
1
Display the desired picture.
1
2
Highlight one of the following options and
press the selector right:
2
Select CIMAGE ROTATE in the playback
menu.
• aINTERNAL MEMORY ybCARD: Copy pic-
tures from internal memory to a memory
card.
• bCARD yaINTERNAL MEMORY: Copy pic-
tures from a memory card to internal mem-
ory.
Press the selector down to rotate the picture
90° clockwise, up to rotate it 90° counterclock-
wise.
3
Press MENU/OK. The picture automatically be
displayed in the selected orientation when-
ever it is played back on the camera.
4
Highlight one of the following options and
press MENU/OK:
• FRAME: Copy selected pictures. Press the se-
lector left or right to view pictures and press
MENU/OK to copy the current picture.
• ALL FRAMES: Copy all pictures.
3
1
• Protected pictures can not be rotated. Remove pro-
tection before rotating pictures (P92).
• The camera may not be able to rotate pictures cre-
ated with other devices.
1
• Copying ends when the destination is full.
• DPOF print information is not copied (P73).
94
Using the Menus: Playback Mode
FVOICE MEMO
n ERASE FACE RECOG.
Add a voice memo to the current photograph. Remove face recognition links from the current
Holding the camera at a distance of about 20 cm, image. When this option is selected, the camera
face the microphone and press MENU/OK to begin will zoom in on an area in the current picture that
recording. Press MENU/OK again to end recording it has matched with a face in the face recognition
(recording ends automatically after 30 seconds).
database. If the match is not correct, press MENU/
OK to remove the link to the face recognition da-
tabase.
1
• Voice memos can not be added to movies or protect-
ed pictures. Remove protection from pictures before
recording voice memos.
• If a voice memo already exists for the current picture,
the options will be displayed. Select RE-REC to re-
place the existing memo.
1
Face recognition links can not be removed from copies
with a size of aor smaller.
KPRINT ORDER (DPOF)
Select pictures for printing on DPOF- and Pict-
Bridge-compatible devices (P71).
Playing Voice Memos
Pictures with voice memos are indicated by a qicon
during playback. To play the voice memo back, select
PLAY for FVOICE MEMO in the playback menu.
1
• The camera may not play voice memos recorded
with other devices.
• Do not cover the speaker during playback.
95
Using the Menus: Playback Mode
JDISP. ASPECT
[4 : 3]
Choose how High Definition (HD) devices display
pictures with an aspect ratio of 4 : 3 (this option is
available only when an HDMI cable is connected).
Select 16 : 9 to display the image so that it fills the
screen with its top and bottom cropped out, 4 : 3
to display the entire image with black bands at
either side.
16:9
4:3
16 : 9
4 : 3
1
Photographs with an aspect ratio of 16 : 9 are displayed
full screen, those with an aspect ratio of 3 : 2/1 : 1 in a
black frame.
96
The Setup Menu
Using the Setup Menu
Display the setup menu.
Adjust settings.
1 1.1 Press
2 2.1 Press the selector right to acti-
MENU/OK to display the
menu for the current mode.
vate the setup menu.
1.2 Press the selector left to high-
2.2 Press the selector up or down
light a left tab.
to highlight a menu item.
1.3 Press the selector up or down
to select 4.
2.3 Press the selector right to dis-
play options for the highlighted
item.
The setup menu appears.
2.4 Press the selector up or down
to highlight an option.
Tab
2.5 Press MENU/OK to select the
highlighted option.
2.6 Press DISP/BACK to exit from the
menu.
97
The Setup Menu
Setup Menu Options
Default values are shown in square brackets [ ].
Option
h HOME
Description
Switch to the time currently selected
for F DATE/TIME (see above).
Switch to local time. If this option is
selected, g and the time and date
will be displayed in yellow for three
seconds each time the camera is
turned on.
F DATE/TIME
Set the camera clock (P17).
N TIME DIFFERENCE
[h]
g LOCAL
Switch the camera clock instantly from your
home time zone to the local time at your desti-
nation when traveling. To specify the difference
between local time and your home time zone:
L a
Choose a language (P17).
Highlight g LOCAL and press the selector
right.
1
o SILENT MODE
[OFF]
Select ON to disable the speaker, flash, and AF-
assist illuminator in situations in which camera
sounds or lights may be unwelcome (note that
the flash will still fire in C mode).
Use the selector to choose the time difference
between local time and your home time zone.
2
Press MENU/OK.
3
To switch between local time and your home
time zone, highlight g LOCAL or h HOME and
press MENU/OK.
98
The Setup Menu
R RESET
A IMAGE DISP.
[1.5 SEC]
Reset all settings except F DATE/TIME, N TIME Choose how long pictures are displayed in the
DIFFERENCE, O BACKGROUND COLOR, and LCD monitor after shooting.
Q VIDEO SYSTEM to default values.
Option
Description
Pictures are displayed for three sec-
onds (3 SEC) or 1.5 seconds (1.5 SEC).
Colors may differ slightly from those
in the final image.
Highlight R RESET and press the selector
right to display a confirmation dialog.
3 SEC
1
1.5 SEC
ZOOM
Highlight OK and press MENU/OK.
2
Pictures are displayed until the MENU/
K FORMAT
(CONTINUOUS) OK button is pressed.
Pictures are not displayed after shoot-
ing.
If a memory card is inserted in the camera, this
option will format the memory card. If no memo-
ry card is inserted, this option will format internal
memory.
OFF
1
OFF has no effect in continuous shooting mode.
3
• All data—including protected pictures—will be de-
leted from the memory card or internal memory. Be
sure important files have been copied to a computer
or other storage device.
• Do not open the battery-chamber cover during for-
matting.
99
The Setup Menu
1
• If the frame number reaches 999-9999, the shutter
release will be disabled (P117).
• Selecting R RESET (P99) sets B FRAME NO. to
CONTINUOUS but does not reset the file number.
• Frame numbers for pictures taken with other cam-
eras may differ.
B FRAME NO.
[CONT.]
Frame number
Newpicturesarestoredinim-
age files named using a four-
digit file number assigned
by adding one to the last file
number used. The file num-
ber is displayed during play-
back as shown at right. B FRAME NO. controls
whether file numbering is reset to 0001 when a
new memory card is inserted or the current mem-
ory card or internal memory is formatted.
100-0001
Directory
number
File
number
G OPERATION VOL.
[c]
Adjust the volume of the sounds produced when
camera controls are operated. Choose e OFF
(mute) to disable control sounds.
Option
Description
H SHUTTER VOLUME
[c]
Numbering continues from the last
file number used or the first avail-
able file number, whichever is higher.
Choose this option to reduce the
number of pictures with duplicate
file names.
Numbering is reset to 0001 after for-
matting or when a new memory card
is inserted.
Adjust the volume of the sounds produced when
the shutter is released. Choose e OFF (mute) to
disable the shutter sound.
CONTINUOUS
e SHUTTER SOUND
[i]
Choose the sound made by the shutter.
RENEW
100
The Setup Menu
I PLAYBACK VOLUME
[7] L DUAL IS MODE
[L]
Adjust the volume for movie and voice memo Choose from the following image stabilization
playback.
options:
Description
Option
L
J LCD BRIGHTNESS
Control the brightness of the display.
[0]
Image stabilization on. If + MOTION
is selected, the camera will adjust
shutter speed to reduce motion blur
when a moving objects are detected.
As above, except that image stabili-
zation is performed only when the
shutter button is pressed halfway or
the shutter is released.
CONTINUOUS +
MOTION
l CONTINUOUS
M SHOOTING
+ MOTION
M AUTO POWER OFF
[2 MIN]
Choose the length of time before the camera
turns off automatically when no operations are
performed. Shorter times increase battery life; if
OFF is selected, the camera must be turned off
manually. Note that in some situations the cam-
era turns off automatically even when OFF is se-
lected.
m
SHOOTING ONLY
Image stabilization off. Choose this
option when using a tripod.
OFF
3
+ MOTION has no effect when sensitivity is set to a
fixed value, and may also be unavailable at some other
combinations of settings. The effect may vary with
lighting conditions and the speed at which the object
is moving.
1 QUICK START MODE
Allow the camera to restart in a fast manner after
turned off (ON/OFF).
[OFF]
3
This option will increase drain on the battery.
F Fn BUTTON
[N ISO]
Choose the role played by the Fn button (P51).
101
The Setup Menu
BRED EYE REMOVAL
[OFF] k AE/AF-LOCK MODE
[P]
Choose ON to remove red-eye effects caused by If AE&AF ON WHEN PRESSING is selected, expo-
the flash when shooting with Intelligent Face De- sure and/or focus will lock while the AFL/AEL but-
tection.
ton is pressed. If AE&AF ON/OFF SWITCH is se-
lected, exposure and/or focus will lock while the
AFL/AEL button is pressed and remain locked until
the button is pressed again (P35).
1
• Red-eye reduction is performed only when a face is
detected.
• Red-eye removal is not available with RAW images.
v AE/AF-LOCK BUTTON
[AE-L]
C AF ILLUMINATOR
If ON is selected, the AF-assist illuminator will light
to assist autofocus.
[ON]
Choose whether the AFL/AEL button locks only
exposure, only focus, or both exposure and focus
(AE-L /AF-L /AE+AF).
3
j RAW
[OFF]
• The camera may be unable to focus using the AF-as-
sist illuminator in some cases. If the camera is unable
to focus in macro mode, try increasing the distance to
the subject.
• Avoid shining the AF-assist illuminator directly into
your subject’s eyes.
Choose whether RAW pictures are recorded
(P55).
jFOCUS CHECK
[ON]
If ON is selected for jFOCUS CHECK, the im-
age will be magnified in the display to assist focus
when the sub-command dial is rotated in manual
focus mode (P46, 47). The camera must be in
manual focus mode.
102
The Setup Menu
I FOCUS CONTROL DIAL
[X CW] M FOCUS SCALE UNITS
[METERS]
Choose the direction in which the sub-command Choose the units used for the focus distance indi-
dial is rotated to increase the focus distance.
cator (P46).
z FRAMING GUIDLINE
[FGRID 9]
Choose the type of framing grid available in shooting mode.
FGRID 9
GGRID 24
HHD FRAMING
For “rule of thirds” composition.
A six-by-four grid.
Frame HD pictures in the crop shown
by the lines at the top and bottom of
the display.
103
The Setup Menu
J COLOR SPACE
[sRGB] m AUTOROTATE PB
[ON]
Choose the gamut of colors available for color re- Choose ON to automatically rotate “tall” (portrait-
production.
orientation) pictures during playback.
Description
Recommended in most situations.
For commercial printing.
Option
sRGGB
Addoobbee RGB
O BACKGROUND COLOR
Choose a color scheme.
[BLACK]
[ON]
c GUIDANCE DISPLAY
Choose whether to display tool tips.
t SAVE ORG IMAGE
[OFF]
Choose ON to save unprocessed copies of seam-
less z panoramas or pictures taken using
B RED EYE REMOVAL, jPRO LOW-LIGHT
MODE, or iPRO FOCUS MODE.
Q VIDEO SYSTEM
Choose a video mode for connection to a TV.
Option
NTSC
Description
Select this mode for connection to
video devices in North America, the
Caribbean, parts of Latin America,
and some East Asian countries.
Select this mode for connection to
video devices in the United Kingdom
and much of Europe, Australia, New
Zealand, and parts of Asia and Africa.
PAL
104
The Setup Menu
S CUSTOM RESET
Reset all settings for mode C1/C2. A confirmation
dialog will be displayed, press the selector up or
down to highlight OK and press MENU/OK.
x POWER MANAGEMENT
[n]
Optimize camera performance for increased bat-
tery life or display quality.
Description
Option
Reduces display refresh rate. The dis-
play dims to save power if no opera-
tions are performed for a short peri-
od, but can be restored by operating
camera controls. Select this option to
save power.
n POWER SAVE
Choose this option for a brighter,
higher quality display and for a lon-
ger delay before the monitor dims to
save power.
o CLLEAR
DISPLAY
1
n POWER SAVE does not take effect when Intelligent
Face Detection is on.
105
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
■Flash Photoggrraphy
■Audiioo//VVisual
Standard TV (available from
third-party suppliers)
EF-20 shoe
EF-42 shoe
mount flash
(sold separately) (sold separately)
mount flash
A/V cable
DXI1GI0TAL CAMERA
■Computer Related
HDTV (available from
third-party suppliers)
USB
HDMI cable
Computer (available from
third-party suppliers)
SD/SDHC/SDXC
memory card
■Printing
USB
SD card slot or card reader
PictBridge-compatible printer
(available from third-party suppliers)
Printer (available from
third-party suppliers)
106
Optional Accessories
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the acces-
sories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.
com/products/digital_cameras/index.html.
Rechargeable
NP-50: Additional large-capacity NP-50 rechargeable batteries can be
Li-iioonn bbatttteerries purchased as required.
Batttteeryy chharrgers BC-45W: Replacement battery chargers can be purchased as required. The
BC-45W charges an NP-50 battery in about 150 minutes at +20°C (+68°F).
AC power
adaptters
AC-5VX (requires CP-50 DC coupler): Use for extended playback or when copying
pictures to a computer (shape of adapter and plug vary with region of
sale).
A/V cable
AV-C1: Use for viewing pictures on TV.
DC coouplers
CP-50: Connect the AC-5VX to the camera.
Shoe Moount Flash EF-20: Hot-shoe clip-on flash, guide number: 20 (ISO 100), compatible with
i-TTL, bounce capability: up to 90°, power source: 2 AA-size 1.5V batteries
107
Optional Accessories
Shoe Moount Flash EF-42: Hot-shoe clip-on flash, guide number: up to 42 (ISO 100), auto zoom:
24-105mm (equivalent to 135 format), compatible with i-TTL, bounce ca-
pability: up to 90°, power source: 4 AA-size 1.5V batteries
Set “Format setting” to “35 mm” when using EF-42 and X10.
Leatherr casseess
Leens hood
LC-X10: This leather case, exclusively for use with the X10, combines practi-
cality with the luxury of leather and comes with a shoulder strap made of
the same material. Pictures can be taken with the camera still in its case.
LH-X10: This aluminum lens hood, exclusively for use with the X10, comes
with an adapter ring made of the same material. The adapter ring is also
used when attaching the φ52 mm filters available from third-party sup-
pliers.
108
Optional Accessories
Attaching the Lens Hoods
Attaching the Filters (available from
third-party suppliers)
Connect the lens
hood and the adapt-
er ring as shown.
Adapter ring
1
Remove the adapter
1
ring from the lens
hood as shown.
Attach the adapter
Lens hood
2
ring to the camera.
Rotate the adapter
ring as shown.
Attach the lens
hood to the camera
with the connected
adapter ring.
Rotate the lens hood
as shown.
2
Attach the filter to the adapter ring.
For details, please refer to the manual sup-
plied with the filter.
3
a
Keep the lens cap in a safe place when not in use.
a
• Only φ52 mm filters can be attached.
• Keep the lens cap in a safe place when not in use.
• Filters cannot be attached directly to the camera.
Make sure to use the adapter ring.
• The lens hood can be attached after the filter is at-
tached.
109
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
Storraggee aanndd UUssee
■ Condensation
If the camera will not be used for an extended pe-
riod, remove the battery and memory card. Do
not store or use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very high tempera-
tures, such as in a closed vehicle on a sunny day
• extremely cold
Sudden increases in temperature, such as occur
when entering a heated building on a cold day,
can cause condensation inside the camera. If this
occurs, turn the camera off and wait an hour be-
fore turning it on again. If condensation forms on
the memory card, remove the card and wait for
the condensation to dissipate.
Clleeaniing
• subject to strong vibration
Use a blower to remove dust from the lens and
monitor, then gently wipe with a soft, dry cloth.
Any remaining stains can be removed by wiping
gently with a piece of FUJIFILM lens-cleaning pa-
per to which a small amount of lens-cleaning fluid
has been applied. Care should be taken to avoid
scratching the lens or monitor. The camera body
can be cleaned with a soft, dry cloth. Do not use
alcohol, thinner, or other volatile chemicals.
• exposed to strong magnetic fields, such as near
a broadcasting antenna, power line, radar emit-
ter, motor, transformer, or magnet
• in contact with volatile chemicals such as pesti-
cides
• next to rubber or vinyl products
■ Wateerr aanndd SSandd
Exposure to water and sand can also damage the
camera and its internal circuitry and mechanisms.
When using the camera at the beach or seaside,
avoid exposing the camera to water or sand. Do
not place the camera on a wet surface.
Traveeling
Keep the camera in your carry-on baggage.
Checked baggage may suffer violent shocks that
could damage the camera.
110
Problems and Solutions
Power and Battery
Problem
Solluution
• The zoom ring (ON/OFF switch) is not correctly rotated: Rotate the zoom ring to OFF and then rotate the
zoom ring again to the point between 28 and 112 (P15).
• The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P10).
• The battery is inserted incorrectly: Reinsert in the correct orientation (P11).
• The battery-chamber cover is not latched: Latch the battery-chamber cover (P11).
• The AC power adapter and DC coupler are connected incorrectly: Reconnect the AC power adapter and
DC coupler.
The camera does not
turn on.
• The battery is cold: Warm the battery by placing it in a pocket or other warm place and reinsert it
in the camera immediately before taking a picture.
• There is dirt on the battery terminals: Clean the terminals with a soft, dry cloth.
•
o CLEAR DISPLAY is selected for x POWER MANAGEMENT: Select n POWER SAVE to reduce the
The battery runs down
quickly.
drain on the battery (P105).
R is selected for shooting mode: Select Bmode to reduce the drain on the battery (P23).
•
• xTRACKING is selected for FAF MODE: Select a different AF mode (P86).
• AF-C is selected for focus mode: Select a different focus mode (P46).
• The battery has been charged many times: The battery has reached the end of its charging life. Pur-
chase a new battery.
• The zoom ring (ON/OFF switch) is not correctly rotated: Rotate the zoom ring to OFF and then rotate the
zoom ring again to the point between 28 and 112 (P15).
• The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P10).
• The AC power adapter or DC coupler has been disconnected: Reconnect the AC power adapter and DC
coupler.
The camera turns off
suddenly.
Charging does not start. Reinsert the battery in the correct orientation and make sure that the charger is plugged in (P10).
Charging is slow.
Charge the battery at room temperature (Pvi).
• There is dirt on the battery terminals: Clean the terminals with a soft, dry cloth.
The charging lamp lights,
but the battery does not
charge.
• The battery has been charged many times: The battery has reached the end of its charging life. Pur-
chase a new battery. If the battery still fails to charge, contact your FUJIFILM dealer.
• The battery is too hot or too cold: Wait for the battery temperature to stabilize (P10).
111
Problems and Solutions
Menus and Displays
Problem
Menus and displays are
not in English.
Solluution
Solluution
Select ENGLISH for Q a (P17, 98).
Shooting
Problem
• Memory is full: Insert a new memory card or delete pictures (P12, 59).
• Memory is not formatted: Format the memory card or internal memory (P99).
• There is dirt on the memory card contacts: Clean the contacts with a soft, dry cloth.
• The memory card is damaged: Insert a new memory card (P12).
• The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P10).
• The camera has turned off automatically: Turn the camera on (P15).
• The indicator lamp was orange when you attempted to record a panorama: Wait until the indicator lamps
turns off (P21).
No picture is taken when
the shutter button is
pressed.
The LCD monitor goes
dark after shooting.
The LCD monitor may darken while the flash charges. Wait for the flash to charge (P37).
• The subject is close to the camera: Select macro mode (P36).
• The subject is far away from the camera: Cancel macro mode (P36).
• The subject is not suited to autofocus: Use focus lock (P34).
The camera does not
focus.
If Sis selected for O IMAGE SIZE in R mode, the camera will optimize not only sensitivity and
other settings, but also image size. To record all pictures at the same size, choose another shooting
mode or select another option for O IMAGE SIZE (P83).
Pictures are not the same
size.
Macro mode is not avail-
able.
Choose a different shooting mode (P23).
Intelligent Face Detection Intelligent Face Detection is not available in the current shooting mode: Choose a different shooting mode
is not available. (P23).
112
Problems and Solutions
Problem
Solluution
• The subject’s face is obscured by sunglasses, a hat, long hair, or other objects: Remove the obstructions.
• The subject’s face occupies only a small area of the frame: Change the composition so that the sub-
ject’s face occupies a larger area of the frame (P34).
• The subject’s head is tilted or horizontal: Ask the subject to hold their head straight.
• The camera is tilted: Keep the camera level (P19).
No face is detected.
• The subject’s face is poorly lit: Shoot in bright light.
Wrong subject is se-
lected.
The selected subject is closer to the center of the frame than the main subject. Recompose the
picture or turn face detection off and frame the picture using focus lock (P34).
• The flash is not available in the current shooting mode: Choose a different shooting mode (P23).
• The camera is in super macro or continuous shooting mode: Turn super macro and continuous shooting
modes off (P36).
• The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P10).
• The camera is in silent mode: Turn silent mode off (P98).
The flash does not fire.
• The flash is not raised: Raise the flash (P37).
• The desired flash mode is not available in the current shooting mode: Choose a different shooting mode
(P23).
• The camera is in silent mode: Turn silent mode off (P98).
Some flash modes are
not available.
• The subject is not in range of the flash: Position the subject in range of the flash (P122).
• The flash window is obstructed: Hold the camera correctly (P19).
• Fast shutter speed selected: Choose a slower shutter speed (P25, 26).
The flash does not fully
light the subject.
• The lens is dirty: Clean the lens (P110).
• The lens is blocked: Keep objects away from the lens (P19).
• sis displayed during shooting and the focus frame is displayed in red: Check focus before shooting
(P116).
• kis displayed during shooting: Use the flash or a tripod (P37).
• A slow shutter speed is selected at high temperatures: This is normal and does not indicated a mal-
function.
Pictures are blurred.
Pictures are mottled.
• The camera has been used continuously at high temperatures or a temperature warning is displayed: Turn
the camera off and wait for it to cool down.
113
Problems and Solutions
Problem
Solluution
Power was interrupted during shooting. Before connecting the AC power adapter or DC coupler,
Pictures are not recorded. turn the camera off. Leaving the camera on can result in corrupted files or damage to the memory
card or internal memory.
The viewfinder display is Diopter adjustment is not adjusted correctly: Slide the diopter adjustment control up and down until the
not clear.
viewfinder display is in sharp focus (P4).
LCD monitor displays
nothing.
Display mode is set to LCD SWITCHED OFF: Press DISP/BACK to choose a different display mode (P6).
Sounds made by the
camera are recorded with
movies.
• u CONTINUOUS is selected for F AF MODE: Select a different AF mode (P86).
• Intelligent Face Detection is on: Turn Intelligent Face Detection off (P52).
Playback
Problem
Solluution
Pictures are grainy.
The pictures were taken with a different make or model of camera.
Playback zoom unavail-
able.
The picture has been saved at a, or is from another make or model of camera (P57).
• The camera is in silent mode: Turn silent mode off (P98).
No sound in voice memo • Playback volume is too low: Adjust playback volume (P101).
and movie playback.
• The microphone was obstructed: Hold the camera correctly during recording (P2).
• The speaker is obstructed: Hold the camera correctly during playback (P2).
Selected pictures are not Some of the pictures selected for deletion are protected. Remove protection using the device
deleted. with which it was originally applied (P92).
File numbering is unex- The battery-chamber cover was opened while the camera was on. Turn the camera off before
pectedly reset. opening the battery-chamber cover (P15).
114
Problems and Solutions
Connections/Miscellaneous
Problem
Solluution
• The camera is not properly connected: Connect the camera properly (P68).
• An A/V cable was connected during movie playback: Connect the camera once movie playback has
ended.
No picture or sound.
• Input on the television is set to “TV”: Set input to “VIDEO”.
• The camera is not set to the correct video standard: Match the camera Q VIDEO SYSTEM setting to
the TV (P104).
• The volume on the TV is too low: Adjust the volume.
No color
Match the camera Q VIDEO SYSTEM setting to the TV (P104).
The computer does not
recognize the camera.
Be sure the camera and computer are correctly connected (P80).
Can not transfer RAW or
JPEG files to computer.
Use the bundled software to transfer pictures (P76).
Pictures can not be
printed.
• The camera is not properly connected: Connect the camera correctly (P70).
• The printer is off: Turn the printer on.
Only one copy is printed/
the date is not printed.
The printer is not PictBridge compatible.
• Temporary camera malfunction: Remove and reinsert the battery (P11) or disconnect and recon-
nect the AC power adapter/DC coupler.
• The battery is exhausted: Charge the battery (P10) or insert a fully-charged spare battery (P11).
The camera is unrespon-
sive.
The camera does not
function as expected.
Remove and reinsert the battery (P11) or disconnect and reconnect the AC power adapter/DC
coupler. If the problem persists, contact your FUJIFILM dealer.
I want to use an AC
power adapter and DC
coupler overseas.
Check the label on the AC power adapter. The AC power adapter can be used with voltages of
100–240V. Consult your travel agent for information on plug adapters.
No sound.
Turn silent mode off (P98).
115
Warning Messages and Displays
The following warnings are displayed in the LCD monitor:
Warning
Description
B(red)
A(blinks red)
k
Low battery. Charge the battery (P10) or insert a fully-charged spare battery (P11).
Battery exhausted. Charge the battery (P10) or insert a fully-charged spare battery (P11).
Slow shutter speed. Pictures may be blurred; use the flash or a tripod.
The camera can not focus. Try one of the following solutions:
• Use focus lock to focus on another subject at the same distance, then recompose the picture
(P34).
s
(displayed in red with red
focus frame)
• Use macro mode to focus when taking close-ups (P36).
Aperture or shutter
The subject is too bright or too dark and the picture will be over- or under-exposed. If the subject
speed displayed in red is dark, use the flash (P37).
FOCUS ERROR
TURN OFF THE CAMERA AND Camera malfunction. Turn the camera off and then on again. If the message persists, contact a
TURN ON AGAIN
FUJIFILM dealer.
LENS CONTROL ERROR
• The memory card or internal memory is not formatted or the memory card was formatted in a computer or
other device: Format the memory card or internal memory using the K FORMAT option in the
camera setup menu (P99).
• The memory card contacts require cleaning: Clean the contacts with a soft, dry cloth. If the message
is repeated, format the card (P99). If the message persists, replace the card.
• Camera malfunction: Contact a FUJIFILM dealer.
CARD NOT INITIALIZED
PROTECTED CARD
BUSY
The memory card is locked. Unlock the card (P12).
The memory card is incorrectly formatted. Use the camera to format the card (P99).
Turn the camera off and wait for it to cool. If no action is taken, the camera will turn off automati-
cally.
p
116
Warning Messages and Displays
Warning
Description
The memory card is not formatted for use in the camera. Format the card (P99).
The memory card contacts require cleaning or the memory card is damaged. Clean the contacts
with a soft, dry cloth. If the message is repeated, format the card (P99). If the message persists,
replace the card.
CARD ERROR
Incompatible memory card. Use a compatible card (P14).
Camera malfunction. Contact a FUJIFILM dealer.
aMEMORY FULL
bMEMORY FULL
INTERNAL MEMORY IS FULL
INSERT A NEW CARD
The memory card or internal memory is full and pictures can not be recorded or copied. Delete
pictures or insert a memory card with more free space.
• Memory card error or connection error: Reinsert the card or turn the camera off and then on again.
If the message persists, contact a FUJIFILM dealer.
• Not enough memory remaining to record additional pictures: Delete pictures or insert a memory card
with more free space.
WRITE ERROR
• The memory card or internal memory is not formatted: Format the memory card or internal memory
(P99).
• The file is corrupt or was not created with the camera: The file can not be viewed.
• The memory card contacts require cleaning: Clean the contacts with a soft, dry cloth. If the message
is repeated, format the card (P99). If the message persists, replace the card.
• Camera malfunction: Contact a FUJIFILM dealer.
READ ERROR
The camera has run out of frame numbers (current frame number is 999-9999). Format the memo-
ry card and select RENEW for B FRAME NO. Take a picture to reset frame numbering to 100-0001,
then select CONTINUOUS for B FRAME NO. (P100).
FRAME NO. FULL
PRESS AND HOLD
THE DISP BUTTON TO
DEACTIVATE SILENT MODE
An attempt was made to choose a flash mode or adjust the volume with the camera in silent mode.
Exit silent mode before choosing a flash mode or adjusting the volume (P21).
• A search has returned more than 30,000 results: Choose a search that returns fewer results.
• More than 999 images are selected for deletion: Choose fewer images.
TOO MANY FRAMES
117
Warning Messages and Displays
Warning
Description
An attempt was made to delete, rotate, or add a voice memo to a protected picture. Remove
protection and try again (P92).
PROTECTED FRAME
aCAN NOT CROP
CAN NOT CROP
apictures can not be cropped.
The picture is damaged or was not created with the camera.
PCANNOT EXECUTE
QCANNOT EXECUTE
aCANNOT EXECUTE
CAN NOT ROTATE
F CAN NOT ROTATE
mCANNOT EXECUTE
F CANNOT EXECUTE
NO CARD
An attempt was made to create a resized copy at a size equal to or larger than the original. Choose
a smaller size.
An attempt was made to rotate a picture that can not be rotated.
Movies can not be rotated.
Red-eye removal can not be applied to the selected picture.
Red-eye removal can not be applied to movies.
No memory card inserted when ECOPY is selected. Insert a memory card.
bNO IMAGE
aNO IMAGE
The source selected for ECOPY contains no images. Select a different source.
• The voice memo file is corrupt: The voice memo can not be played back.
• Camera malfunction: Contact a FUJIFILM dealer.
uERROR
The DPOF print order on the current memory card contains more than 999 images. Copy the
pictures to internal memory and create a new print order.
DPOF FILE ERROR
CAN NOT SET DPOF
F CAN NOT SET DPOF
The picture can not be printed using DPOF.
Movies can not be printed using DPOF.
A connection error occurred while pictures were being printed or copied to a computer or other
device. Confirm that the device is turned on and that the USB cable is connected.
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). To
resume printing, turn the printer off and then turn it back on.
COMMUNICATION ERROR
PRINTER ERROR
PRINTER ERROR
RESUME?
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). If
printing does not resume automatically, press MENU/OK to resume.
118
Warning Messages and Displays
Warning
Description
An attempt was made to print a movie, a picture not created with the camera, or a picture in a
format not supported by the printer. Movies and some pictures created with other devices can
not be printed; if the picture is a still picture created with the camera, check the printer manual to
confirm that the printer supports the JFIF-JPEG or Exif-JPEG format. If it does not, the pictures can
not be printed.
CANNOT BE PRINTED
119
Internal Memory/Memory Card Capacity
The following table shows the recording time or number of pictures available at different image sizes.
All figures are approximate; file size varies with the scene recorded, producing wide variations in the
number of files that can be stored. The number of exposures or length remaining may not diminish at
an even rate. A limited number of test pictures can be taken when no memory card is inserted.
Medium
Internnall memory
(approxx. 26 MB)
4 GB
8 GB
O
T
FINE
5
7
NORMAL
FINE
820
NORMAL
1300
1720
2530
3350
4590
5160
FINE
1650
2200
2640
3500
4880
7110
NORMAL
2620
3450
5080
6720
9210
O4:3
O16:9
P4:3
P16:9
Q4:3
8
11
16
22
30
35
1090
1310
1740
2430
3540
8
11
16
23
Q16:9
10370
i19201
h12801
f2
12sec.
17sec.
42sec.
32sec.
65sec.
32sec.
38min.
49min.
115min.
85min.
172min.
86min.
76min.
98min.
232min.
112min.
345min.
172min.
Y 640 × 4803
Y 320 × 2403
Y 320 × 1123
1 Use a Gcard or better. Individual movies can not exceed 29 minutes in length.
2 Individual movies can not exceed 115 minutes in length.
3 Use a Gcard or better. Individual movies can not exceed 30 seconds in length.
120
Specifications
System
Model
Digital Camera X10
Effective pixels
Image sensor
Storage media
File system
12 million
2
/
3 -in., EXR CMOS with primary color filter
• SD/SDHC/SDXC memory cards
• Internal memory (approx. 26MB)
Compliant with Design Rule for Camera File System (DCF), Exif 2.3, and Digital Print Order Format
(DPOF)
File format
• Still pictures: Exif 2.3 JPEG (compressed); RAW (original RAF format, special-purpose software required); RAW+JPEG
available
• Movies: MOV (H.264) (stereo)
• Audio: WAV (stereo)
Image size (pixels)
• O4 : 3: 4,000×3,000 • O3 : 2: 4,000×2,664 • O16 : 9: 4,000×2,248 • O1 : 1: 2,992×2,992
• P4 : 3: 2,816×2,112 • P3 : 2: 2,816×1,864 • P16 : 9: 2,816×1,584 • P1 : 1: 2,112×2,112
• Q4 : 3: 2,048×1,536 • Q3 : 2: 2,048×1,360 • Q16 : 9: 1,920×1,080 • Q1 : 1: 1,536×1,536
• r MOTION PANORAMA v: 1,624×11,520 (tall)/11,520×1,080 (wide)
• r MOTION PANORAMA w: 1,624×5,760 (tall)/5,760×1,080 (wide)
• r MOTION PANORAMA x: 1,624×3,840 (tall)/3,840×1,080 (wide)
• r MOTION PANORAMA z: 1,624×11,520 (tall)/11,520×1,080 (wide)
Digital zoom
Lens
Focal length
About 2.0× with intelligent digital zoom (up to 8 × when combined with optical zoom)
Fujinon 4×optical zoom lens, F2.0 (wide angle)–F2.8 (telephoto)
f=7.1mm–28.4mm (35-mm format equivalent: 28 mm– 112 mm)
F2.0–F11 (wide angle)/F2.8–F11 (telephoto) in increments of 1 3 EV
/
Aperture
Focus range (distance from • Approx. 50cm (1.6ft.)–infinity (wide angle); 80cm (2.6ft.)–infinity (telephoto)
front of lens)
• Macro: approx. 10cm–3m/0.3ft.–9.8ft. (wide angle); 50cm–5m/1.6ft.–16.4ft. (telephoto)
• Super macro: approx. 1cm–1m/0.3in.–3.2ft. (wide angle)
Sensitivity
Standard output sensitivity equivalent to ISO 100, 200, 250, 320, 400, 500, 640, 800, 1000, 1250, 1600,
2000, 2500, 3200, 40001, 50001, 64001, 128002; AUTO, AUTO (400), AUTO (800), AUTO (1600), AUTO (3200)
1 image size Por Q
2 image size Q
Metering
256-segment through-the-lens (TTL) metering; MULTI, SPOT, AVERAGE
121
Specifications
System
Exposure control
Exposure compensation
Scene modes
Programmed AE (with program shift), shutter-priority AE, aperture-priority AE, and manual exposure
–2EV–+2EV in increments of 1 3 EV
/
C (NATURAL & N), D (NATURAL LIGHT), L(PORTRAIT), Z(PORTRAIT ENHANCER),
M(LANDSCAPE), N(SPORT), O(NIGHT), H(NIGHT (TRIPOD)), U (FIREWORKS), Q(SUNSET),
R(SNOW), V (BEACH), f (UNDERWATER), U(PARTY), V(FLOWER), W(TEXT)
Optical stabilization (lens-shift type)
Picture stabilization
Shutter speed (combined • O: 1 4 s– 1,000 s
mechanical and electronic
shutter)
1
1
1
/
/
/
• H: 3s– 1,000 s
/
• U: 4s– 2 s
• P, AUTO, Adv., SP (except O, H, and U): 1 4 s– 4,000 s
• Other modes: 30s– 4,000 s
1
/
/
1
/
Continuous
• I: max. 200 frames; frame rate can be selected from 10, 7, 5, and 3 fps (The frame rate varies depending on the
shooting conditions or numbers of frames in continuous shooting.)
• P: 16 or 8 frames (RAW+JPEG/RAW: max. 8 frames); frame rate can be selected from 10, 7, 5, and 3 fps
• O: 3 frames (selected exposure, overexposure, underexposure)
• W: 3 frames (selected sensitivity, sensitivity raised, sensitivity lowered)
• X: 3 frames (PROVIA, Velvia, ASTIA)
• Y: 3 frames (100%, 200%, 400%)
Focus
• Mode: Single AF, continuous AF, manual focus
• Focus-area selection: Multi, area, tracking
• Autofocus system: Contrast-detect TTL AF
White balance
Automatic scene detection; 8 manual preset modes for direct sunlight, shade, daylight fluorescent,
warm white fluorescent, cool white fluorescent, incandescent lighting, underwater, color tempera-
ture ; custom white balance
Self-timer
Flash
Off, 2sec., 10sec.
Manual pop-up flash; effective range when sensitivity is set to AUTO (800) is approx. 30cm–7.0m/0.9ft.–
22.9ft. (wide angle), 50cm–5.0m/1.6ft.–16.4ft. (telephoto)
Flash modes
Auto, forced flash, off, slow synchro (red-eye removal off); auto with red-eye removal, forced flash
with red-eye removal, off, slow sync with red-eye removal (red-eye removal on)
Optical zoom viewfinder; frame coverage approx. 85%
Optical viewfinder
Monitor
2.8-in., 460k-dot color LCD monitor; frame coverage approx. 100%
122
Specifications
System
Movies
• i1920: 1,920×1,080 (1080p), 30 fps
• f: 640×480 (VGA), 30 fps
• Y 320 × 240: 320×240, 120 fps
• h1280: 1,280×720 (720p), 30 fps
• Y 640 × 480: 640×480, 70 fps
• Y 320 × 112: 320×112, 200 fps
Note: i, h, and fmovies are recorded with stereo sound.
Languages
Arabic, Bulgarian, Simplified Chinese, Traditional Chinese, Czech, Danish, Dutch, English, Farsi, Finnish,
French, German, Greek, Hebrew, Hungarian, Indonesian, Italian, Japanese, Kazakh, Korean, Latvian,
Lithuanian, Norwegian, Polish, Portuguese, Romanian, Russian, Serbian, Slovak, Spanish, Swedish,
Thai, Turkish, Ukrainian, Vietnamese
Input/output terminals
A/V OUT (audio/video output) NTSC or PAL output with monaural sound
HDMI output
HDMI Mini Connector
Digital input/output
USB 2.0 High-Speed; shares A/V OUT connector; MTP/PTP
Power supply/other
Power sources
• NP-50 rechargeable battery
• AC-5VX AC power adapter and CP-50 DC coupler (sold separately)
Battery life (approximate num-
ber of frames that can be taken
with a fully-charged battery)
Battery type
NP-50 (type supplied with camera)
Appproxximaate number of fframes
270
CIPA standard, measured in B(auto) mode using battery supplied with camera and SD memory card.
Note: Number of shots that can be taken with battery varies with battery charge level and will decline
at low temperatures.
Camera dimensions
Shooting weight
Camera weight
117.0mm×69.6mm×56.8mm/4.6in. ×2.7in. ×2.2in. (W × H × D)
Approx. 350g/12.3oz., including battery and memory card
Approx. 330g/11.6oz., excluding battery, accessories, and memory cards
Operating conditions
• Temperature: 0°C–+40°C/+32°F–+104°F
• Humidity: 10%–80% (no condensation)
123
Specifications
NP-50 rechargeable battery
Nominal voltage
DC 3.6V
Nominal capacity
1000mAh
Operating temperature
Dimensions (W × H × D)
Weight
0°C–+40°C/+32°F–+104°F
35.4mm×40.0mm×6.6mm/1.3in. ×1.5in. ×0.2in.
Approx. 18g/0.6oz.
BC-45W battery charger
Rated input
Input capacity
100V–240V AC, 50/60Hz
• 100 V: 8.0VA
• 240 V: 12VA
Rated output
4.2V DC, 550mA
Supported batteries
Charging time
NP-50 rechargeable batteries
Approx. 150 minutes (+20 °C/+68 °F)
Dimensions (W × H × D)
Weight
91mm×62mm×23mm/3.5in. ×2.4in. ×0.9in., excluding projections
Approx. 67g/2.3oz., excluding battery
Operating temperature
0°C–+40°C/+32°F–+104°F
Weight and dimensions vary with the country or region of sale.
124
Specifications
Color Television Systems
NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in
the U.S.A., Canada, and Japan. PAL (Phase Alternation by Line) is a color television system adopted mainly in
European countries and China.
Notices
• Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/
digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual.
• Although the monitor is manufactured using advanced high-precision technology, small bright points and
anomalous colors (particularly in the vicinity of text) may appear. This is normal for this type of monitor and
does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electric-
ity, or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.
125
Restrictions on Camera Settings
Shooting Mode and Camera Settings
The options available in each shooting mode are listed below.
E
Adv.
U B i j r
SP
D h Z M N O H p Q R
R
S
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
T
✔
✔
✔
✔
✔
✔
P
S
A
M
C
✔
✔
s
f U V W
F
1
1
1
1
1
1
1
1
1
1
1
OFF
F
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
1
1
F
✔
✔
G
✔
AUTO
N
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔
B
OFF
ON
O
✔
✔
✔
✔
✔ ✔1
1
1
1
1
1
P
✔
✔
✔
✔ ✔1 ✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔1
✔
✔
N4
K
✔
✔
✔
✔
✔
✔
L
M
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔1
✔
✔
B
✔
✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔1
1
1
1
P
✔
✔
✔ ✔1 ✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
h
S/R
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
P
J
K
O
I
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
DRIVE
P
O
W
X
Y
d
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
126
Restrictions on Camera Settings
E
Adv.
U B i j r
SP
D h Z M N O H p Q R
R
S
T
P
S
A
M
C
s
f U V W
F
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AUTO
AUTO (32200)
AUTO (11600)
AUTO ((800)
AUTO ((400)
12800
6400
5000
4000
3200
2500
2000
1600
1250
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
N
1000
800
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
640
500
400
320
250
200
100
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
o
✔
✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
5
p
✔
q
✔
✔
s
✔
✔ ✔1
✔
F6
t
✔
✔ ✔1
✔
1
1
x
✔
✔
✔
127
Restrictions on Camera Settings
E
Adv.
U B i j r
SP
D h Z M N O H p Q R
R
S
✔
✔
✔
✔
T
✔
✔
✔
✔
P
S
A
M
C
✔
✔
✔
s
✔
✔
✔
f U V W
F
1
AF-C
AF-S
MF 7
✔
✔
✔
✔
✔
✔
✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
1
1
✔
✔
✔
✔
✔
✔
AUTO
O
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
O
P
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔1
Q
T
✔
✔
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AUTO
A
B
C
D
M
c
✔
✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔
1
1
✔
✔
✔
✔
✔
✔
✔
U
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
d
e
b
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
P
e
d
f
f
d
f
H
r
s
h
128
Restrictions on Camera Settings
E
Adv.
U B i j r
SP
D h Z M N O H p Q R
R
✔
S
T
P
S
A
M
C
s
f U V W
F
R
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Z
b
✔
2
3
3
3
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔3
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔2
✔
✔
✔
✔
✔ ✔3
✔
✔
✔
✔
✔
✔ ✔3 ✔ ✔3
✔
✔
n
✔
✔
✔
✔
✔
F (F mode)
✔
✔
✔
✔
✔
✔
✔
i1920
h1280
f
W
k640×480
k320×240
k320×112
I
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
g
K
✔
✔
✔
✔
✔
✔
✔
1
L
l
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
L
M
m
✔
✔ ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
1
OFF
✔
✔ ✔3
✔
✔
✔ ✔3
3
3
3
C
j
✔
3
✔ ✔3
✔
✔
✔
✔
✔
✔ ✔3
✔
✔
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
✔
✔
✔
✔
✔ ✔3
✔
✔
✔ ✔3
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
1 Optimized for selected shooting mode.
2 ON selected automatically.
3 OFF selected automatically.
4 Flash disabled in all shooting modes if lowered.
5 o (MULTI) selected automatically when Intelligent Face Detection is on.
6 Camera focuses on faces when Intelligent Face Detection is on.
7 Intelligent Face Detection turns off automatically in manual focus mode.
129
Memo
130
Memo
131
Memo
132
Memo
133
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Printed in
Please contact your local distributor for repairs and technical support. (see Worldwide
Network list)
|