4. Tools
4.1 Information
4.2 Factory Setting
5. Game
23
24
24
24
25
25
25
26
26
26
26
26
26
26
26
27
27
27
27
27
6. Hot key
6.1 Info
6.2 EPG
6.3 Find
6.4 Number
6.5 TV/Radio
6.6 Up/Down
6.7 Left/Right
6.8 Mute
6.9 Pause
6.10 OK
6.11 Audio
6.12 Recall
6.13 Fav
6.14 Teletext
6.15 Zoom
TROUBLE SHOOTING
28
A Digital Satellite Receiver is a convenient product that allows you to view a variety
of programs provided through satellite. This user's guide covers the installation of
the DSR and the necessary steps to implement various features. This also explains
special features available only in this DSR in detail, which will allow you to make full
of these feature.
Information confirmed in this document is subject to change. We reserves the right,
without notice, to make change in product design or performances as progress in
engineering or technology.
Main Features
High quality Video & Audio & DigitalAudio
Fully MPEG-2, DVBcompliant
Provide friendly andeasy-to-use menu system
Various channel editing function(Favorite, moving, locking, renaming, deleting and
sorting)
User programmable variousSatellite & Transponder information
Automatically search fornewly added transponder
Stores up to4000 channels
Easy and speedysoftware upgrade throughRS-232 port
Plug-and-play data transfersystem (DSR toDSR)
Timer function, automatically turns On/Off by settingfunction (daily, monthly, yearly)
Automatic reserved channelmoving system
Provide Electronic ProgramGuide (EPG)
Teletextfunction support
256 colors On-Screen-Display
Last channel automaticallysaving
For Your Safety
To avoid electric-shock hazards, do not
open the cabinet, refer servicing to qualified
personnel only.
Keep the receiver away from flower vases,
tubs, sinks, etc., in order to avoid damaging
the equipment.
Do not expose the receiver un-der the
sunlight. And keep it away from the heat
source.
Do not block ventilation holes of the
Receiversothataircancirculatefreely.
When the abnormal phenomenon occur,
youshouldcutoffthepowerimmediately.
Do not touch the receiver during thunder,
since that might create electric-shock
hazards.
Switch the receiver off whenever it remains
out of service for an extended period.
Be sure to turn the Receiver off and
disconnect the AC power cord before
cleaning the Receiver surface. If the
surface is dirty, wipe clean with a cloth
which has been dipped in a weak soap-and-
water solution and wrung out thoroughly,
and then wipe again with a dry cloth.
R
Remote Control
Batteries
User's Guide
General Operation
Throughout this manual you will notice that the everyday operation of the receiver is
based on a series of user friendly on screen display and menus. These menus will
help you get the most from your receiver, guiding you through installation, channel
organizing, viewing andmany other functions.
All function can be carried out using the buttons on the RCU, and some of the
function can alsobe carried outusing the buttonson the frontpanel.
The receiver is easy to use, always at your command and adaptable for future
advances.
Please be awarethat new softwaremay change thefunctionality of thereceiver.
Should you experience any difficulties with the operation of your receiver, please
consult the relevant section of this manual, including the Problem Shooting, or
alternatively call yourdealer or acustomer service adviser.
RCU
Key
Function
Turns power ON/OFF of theDSR
.,*?!@
ABC
JKL
TUV
DEF
MNO
When watching a channel, mute the sound
Enter number of the required menu item or
select a channel number to watch
0~9
GHI
TV/RADIO Switches between TVand Radio mode
PQRS
WXYZ
Switches back toprevious channel
Display the favoritegroup list
Display the satellite list
PR
FAV
.
SAT
Display the Findwindow
FIND
Show information ofthe current channel
Press this key one time to run menu onscreen
Moves up /down a pagein the list
INFO
MENU
PR+
Executes the selecteditem in themenu screen
or enters thedesired value inany input mode
OK, LIST
PR+, PR-
When watching achannel, change channelsor
move to thenext higher orlower item inthe menu
OK
LIST
When watching achannel, adjust thevolume or
move to theleft or rightitem in themenu
PR
FAV
EXIT
Return to the previous menu on the menu
screen or escape from the menu
EXIT
EPG
SAT
TV/AV
SLEEP
TXT
Call up the EPG (Electronic Program Guide)
Display the Audio window.
L
L
R
ZOOM
FIND
R
TV/AV
TXT
Switch between TV and AV modes
Switch to teletextor subtitle mode
Enter into thezoom in mode
INFO
ZOOM
Press once to pause the screen picture, press
once again to go to the normal mode
PAUSE
R
SLEEP
Enter into thesleep in mode
Enter into thenine-pictures mode displayed
on the screen.
Rear Panel
LNB IN: CONNECTTO SATELLITE ANTENNA
LNB OUT:CONNECT TOTHE OTHER RECEIVER
CONNECT TOA PC FOR S/WUPGRADE
CONNECT TOTV ANDVCR
USING ASCART CABLE
POWER ON/OFF
CONNECT TO ADIGITAL AMPLIFIER
CONNECT TOAUDIO R/LTO TV ORAUDIO TUNER
CONNECT VIDEO TO TV USING RCAJACK
CONNECT TO12V TO AN EXTERNAL 0/12V SWITCH
RF OUT: CONNECT TO TV ANT INPUT
Connecting to TVusing SCART support
Satellite
Dish
DSR
IN
TV
SCART
Connecting to TV using RCA support
IN
VIDEO
AUDIO
R
Satellite
Dish
TV
L
DSR
Connecting to DigitalAmplifier
Satellite
Dish
DIGITALAUDIO
CONVERTOR OR
AMPLIFIER
L
R
DIGITAL AUDIO
SPEAKER
Main Menu
Make sure that you have properly installed and connected the cables of the receiver
well. If the receiver is the factory status or there is no program list, when power on,
the Main Menu window will be displayed on the screen.
During the normal TV/Radio mode, press MENU key on the RCU to enter into the
Main Menu window.
This menu consists of 5 major main menus
as follow.
- Edit Channel
- Installation
- System Setup
- Tools
- Game
During the installation the OK key confirms a selection and LIST key shows Down
List Box if the column has
RCU to enter numeric value.
mark. You can also use the numeric keys on the
Use the PR+, PR- key to move upwards and downwards from one line to another
line and use key to move from main menu to sub menu and move from left
side to right side or versa.
Meantime, you want to escape the menu system, please press MENU or EXIT key
on the RCU.
If there is no program, you can not exit from the Main Menu window by pressing
MENU or EXIT key. System will inform"No channel" andthe following itemsturn grey.
Sub-menu
Turn grey when there is no program
Edit Channel
TV Channel List
Radio Channel List
Delete all
Delete channels by satellite
Installation
Antenna Connection Satellite List
Antenna Setup Single Satellite Search
Multi Satellite Search
TP List
Language TV System Local Time Setting
Timer Setting Parental Lock OSDSetting
Favorite Other
System Setup
Information
Factory Setting
Tools
Game
SatcoDX Auto Programing
Tetris
Othello
1. Edit Channel
1. Press OK key or
key to pop up the
"Input Password" dialogue, you can not
enter into the menu unless the correct
password is inputted. The default password
is "0000".
2. Press PR+, PR- keys to move the cursor
up or down.
3. Press EXIT key or
key to move the
focus to theleft menu.
1.1 TV ChannelList
1. Press
keys to select satellite.
2. Press PR+, PR- keys to select the program
that you want to play, and then press OK key
to view it in the small window. If move the
yellow cursor to select up or down, you will
see a gray line which indicates the playing
program in the small window.
3. Press FAV key to move the FAV button upward.
Select the program and press OK key to pop up the
favourite group list. In the list, select the group that
you want to add into and press OK key, and then
you will find the favourite mark is displayed at the
right side of the selected program.
Press FAV key again to exit from the fav mode, and
you will find the FAV button return to the origin
position.
4. Press red colour key to move the Lock button
upward. Select the program and press OK key to
mark this program with the Lock mark. You can
cancel this mark by pressing OK key once more.
Press red colour key again to exit from the lock
mode, and you will find the Lock button return to the
origin position.
5. Press green colour key to move the Skip button
upward. Select the program and press OK key to
mark this program with the skip mark. You can cancel
this mark by pressing OK key once more.
Press green colour key again to exit from the skip
mode, and you will find the Skip button return to the
origin position.
6. Press yellow colour key to move the Move button
upward. Select the program and press OK key to
mark this program with the move mark. Press PR+,
PR- keys to move the cursor to the position where
you want to locate and press OK key to confirm.
Press yellow colour key again to exit from the
yellow mode, and you will find the yellow button
return to the origin position.
7. Press blue colour key to enter into the Edit
channel window.
i . Sort(red colour key)
Press red colour key to pop up the Sort drop-down
list.
Name(A-Z): The ascending order, omitting the $
character, the number is ahead, then the capital
letter, at last the lowercase.
Name (Z-A): The opposite order of the above Name
(A-Z).
Free/Scramble:: All FTA programs are listed ahead,
while all scrambled programs are listed last.
Lock: all locked programs are listed at the last.
ii. Edit (greencolour key)
Press green colour key to move the Edit button
upward. Select the program and press OK key to
pop up the Rename window.
In Rename window, press red colour key to switch
between capital letter and lower letter; press green
colour key to delete the character on the cursor;
press
keys to move the cursor left or right;
press numeric keys (0-9) to input the character,
please refer to the down table. Press yellow colour
key to save and exit, or press blue key to cancel and
exit.
Numeric keys
Press numeric keyrepeatedly, displayin circle
1
2
3
4
5
6
7
8
.,*?!@1
ABC2
DEF3
GHI4
JKL5
MNO6
PQRS7
TUV8
WXYZ9
[space]_-0
9
0
If the name is empty, system will pop up a dialogue informing "Name" once yellow
colour key ispressed. Press OK key to closethis dialogue.
iii. Delete (bluecolour key)
In Delete window, press blue colour key to move the
Delete button upward. Select the program and press
OK key to mark this program with the deletion mark.
You can cancel this mark by pressing OK key again.
Press EXIT key to pop up the dialogue "Are you sure
to save?". Select Yes button and press OK key to
save, or select NO button and press OK key to exit
without saving.
1.2 Radio ChannelList
Sine the sameoperation as 1.1 TV ChannelList, here wedon't explain anymore.
1.3 Delete All
Move cursor to the Delete All item, and press OK
Key to pop up the dialogue "Warning! Do you really
want to delete all channel?".
Press EXIT key to pop up the dialogue "Are you
sure to save?". Select Yes button and press OK key
to save, or select NO button and press OK key to
exit without saving.
1.4 Delete Channelsby satellite
Move cursor to the Delete channels by satellite
item, and press OK key to pop up the dialogue
"Warning! Do you really want to delete all
channel?".Select Yes button and press OK key to
delete the channels, or select NO button and press
OK key to exit without deleting.
2. Installation
1. Press OK key or
key to pop up the
"Input Password" dialogue, you can not
enter into the menu unless the correct
password is inputted. The default password
is "0000".
2. Press PR+, PR- keys to move the cursor
up or down.
3. Press EXIT key or
key to move the
focus to theleft menu.
2.1 Antenna Connection
Press
keys to select between Motor
Antenna and Fixed Antenna.
2.2 Satellite List
1. Press PR+, PR- keys to select the satellite
up or down. Press OK key to select and
mark, and you can press OK key again to
cancel the selection and the mark.
2. If there is no satellite, the red colour and
blue colour keys will be invalid.
3. Press red colour key to pop up the Edit
Satellite window. Press PR+, PR- keys to
move cursor up or down.
Name: User numeric keys to change the
name of the satellite, please refer to the
Edit Channel Name.
Longitude: You can press
keys to switch between east longitude and west
longitude. After pressing OK key, you can use numeric keys to edit the longitude,
press EXIT key or the PR+, PR- keys to exit editing mode. The range of the
longitude is from 1to 180 degree. If beyond this range, system will inform you "out of
range" when youpress yellow colour key onthe RCU.
After setting, press yellow colour key to save and exit, while press blue colour key
to exit withoutsaving.
4. Press green colour key to pop up the Add
Satellite window. Since the same operation
as the above Edit Satellite window, here we
don't explain any more.
5. Press blue colour key to pop up the
dialogue "Are you sure to delete?". Select
Yes button and press OK key to delete the
selected satellite. You can cancel this
operation by pressing OK key at the NO
button.
2.3 Antenna Setup
Part A: Fixed
Suppose that you have selected Fixed
Antenna in theAntenna Connection window.
1. Satellite: All selected satellites in the
satellite list aredisplayed in thisitem.
Press
keys to select the satellite in
circle. Or press OK key to pop up the drop-
down list, then select the desired satellite in
the list andpress OK key to confirm.
2. LNB Freq, Transponder, DiSEqC1.0,
DiSEqC1.1: The same operation as the
above.
3. 22K, 0/12V, Toneburst, Polarity: You
can press
keysto select incircle.
Part B: Motor
Suppose that you have selected Moter
Antenna in theAntenna Connection window.
1. LNB Type: Select the properLNB type.
2. Motor Type: Select between DiSEqC1.2
and USALS. If you select DiSEqC1.2, the
following Local Longitude and Local Latitude
items will turngrey.
3. Delete All: Press OK key to pop up the
dialogue "Are you sure to clear set satellite
position of this tuner?". Press OK key at the
Yes button to clear all the memories about
the position of the satellites that has
connected to thecurrent turner.
4. Motor Setting: Press OK key to the Motor
Setting window.
Satellite: Press
keys to select the
satellite in circle. Or press OK key to pop up
the drop-down list, then select the desired
satellite in the list and press OK key to
confirm.
Transponder: The same operation as the
above.
Position No., & Save: The range is from 0 to 63. "0" delegates the original position.
You can select theproper value whenyou has rotatedthe antenna.
Go to X: Press OK key to pop up the drop-down list, select the proper position
(reference or from1to 63) torealize the selectedposition.
West <Save> East: Press
key to turn west, while press
key to turn east.
Press OK key to pop up the dialogue "Are you sure to change this satellite's
position?". Press OK key at the Yes button to save the current position, or press OK
key at theNo button tocancel the operation.
Recalculation: Press OK key to pop up the dialogue "Are you sure to change this
satellite's position?". PressOK key at theYes button to recalculation.
5. Limit Setup: Press OK key to pop up the
Limit Setup window.
Limit Setup: Press
keys to switch
among Disable Limit, East Limit and West
Limit.
Limit Setup: Move cursor to the Limit Setup
button. You can press
key to turn west ,
or press key to turn east.
Go to Reference: Press OK key to go to
reference. If you select Disable Limit in the
above Limit Setup item, this button will turn
grey.
6. If select USALS, Delete All item will turn
grey.
Local Longitude, Local Latitude: Press
keys to switch between West and
East, or press
keys to switch between
North and South. Press OK key to enter into
the editing mode. Use numeric keys (0-9) to
input the longitude or latitude, press MENU
key or EXIT key to exit. The range of the
longitude is from 0 to 180,while the range of
the latitude is from 0 to 90. If the inputted
value is not in this range, system will pop up
a dialogue "Out of Range" when exit from
this window. You can press OK key to close
this dialogue.
7. Motor Setting: Press OK key to enter into
the Motor setting window.
Satellite, Transponder: Press
keys
to select satellite or transponder, or press
OK key to pop up the drop-down list and
select in the list.
2.4 Single SatelliteSearch
1. Satellite : Press
keys to select the
satellite in circle. Or press OK key to pop up
the drop-down list, then select the desired
satellite in the list and press OK key to
confirm.
2. FTA Only: Press
keys to select
between Yes and No.
3. Scan Channel: Press
keys to
select among TV+Radio, TV Channel, Radio.
4. Network Search: Select between No and
Yes. This item turns grey when Auto Scan is
selected in thefollowing Scan modeitem.
5. Scan Mode: Press
keys to select
between Auto Scan and Preset Scan. Auto
Scan is Blind scan, while Preset Scan is to
search the presetfrequencies.
6. Search: Press OK key to startsearching.
2.5 Multi SatelliteSearch
From the Multi Satellite Search window,
you can search several satellites at the one
time.
1. Satellite: All selected satellites in the
satellite list window are displayed on the
down part. You can press
switch among them.
keys to
keys to select
keys to
2. FTA Only: Press
between Yes and No.
3. Scan Channel: Press
select among TV+Radio, TV Channel, Radio.
4. Network Search: Select between No and Yes. This item turns grey when Auto
Scan is selectedin the followingScan mode item.
5. Scan Mode: Press
keys to select between Auto Scan and Preset Scan.
Auto Scan isBlind scan, whilePreset Scan isto search thepreset frequencies.
6. Search: Press OK key to startsearching.
2.6 TP List
1. Press PR+,PR- keys to select the proper
satellite.
2. Press red colour key to pop up the Edit TP
window.
Frequency, Symbol rate: Press
keys to add or reduce by step one. Or press
numeric keys (0-9) to input the desired
value. The range of the frequency is 3000-
13450, while the range of the symbol rate is
1000~45000. The inputted value is beyond
this range, the value will return to the origin
value.
Polarity: Press
keys toswitch between
Vertical andHorizontal.
3. Press green colour key to pop up the Add
TP window. Since the same operation as the
above Edit TP window, here we don't explain
any more.
4. Press yellow colour key to pop up
dialogue " Are you sure to delete?". Press
OK key at the Yes button to delete the
selected TP, or press EXIT key to cancel the
operation.
5. Press blue colour key to pop up the TP
Search window.
FTA only, Scan Channel, Network Search:
Press
keys to select the proper
option.
Press OK key at the OK button to start
searching.
1. Press OK key or
key to move the
cursor to theright menu.
2. Press PR+, PR- keys to move the cursor
up or down.
3. Press EXIT key or
key to move the
focus to theleft menu.
3. System Setup
3.1 Language
1. Press OK key to enter into the Language
window. Press keys to select the
language in circle, while press PR+, PR-
keys to movethe cursor upor down incircle.
2. Press MENU key or EXIT key to save and
exit.
3. The types of the language, pleaser refer to
the configuration ofthe customer.
3.2 TV System
Press PR+, PR- key to move the cursor up or
down, while press
keys to change the
setting and the setting will take effect
immediately.
1. Display Mode: Select among Auto,PAL,
PAL-M, PAL-N, NTSC.
2. Aspect Mode: Select among 4:3LetterBox,
4:3PanScan, 16:9.
3. Video Output: Select between RGB and
CVBS.
4.RF System: Select among PAL-BG,PAL-I,PAL-DK and NTSC.
5.RF Channel: PAL:21-69,ntsc:14-83.
3.3 Local Time Setting
1. Summer Time: Select between ON and
OFF. "OFF" delegates the normal time. If
select ON, timewill add onehour.
2. GMT Offset: When select "ON" in GMT
Usage item, systemwill get thedate and time
information from the screen automatically.
Date and Time two items will turn grey.
Select the proper option in the GMT Offset
item. The default setting isGMT ON.
3.Date, Time: When select "OFF" in GMT Usage, Date and Time two items take
effect, while GMT Usage turns grey. Use numeric keys to input the desired value.5.
After setting, press MENU key or EXIT key to exit and save. If the value is invalid,
system will inform "Invalid input! Continue to edit?". Press OK key at the Yes button
to continue themodification, or pressOK key at theNo button toexit without saving.
3.4 Timer Setting
If there is no program, you can not enter into
this window. There are 8 timers that can be
set. Select Timer up or down, and press OK
key to enterinto the settingwindow.
1. Timer mode: The default mode is off. You
can set the timer once, daily, weekly,
monthly and yearly.
2. Timer Service: You can select Channel
the Wakeup Channel is displayed in the
following item.
3. Wakeup Date, On Time: Use numeric
keys to inputthe valid date.
Duration: Set the gap time. After waking up, system will power off automatically
after the durationtime.
Press MENU or EXIT key to saveand exit.
3.5 Parental Lock
Before entering into the Parental Lock
window, youneed input thecorrect password.
The default passwordis 0000.
1. Menu Lock: Press
keys to select
between Off and On. If select "On" , you can
not enter into the most window before
entering the password.
2. Channel Lock: Press
keys to select
between Off and On. The default valueis Off.
If select "On", you can not view the locked channel set in Chanel List Edit window
until you haveinputted the correctpassword.
3. New Password:User numeric key (0-9)to input thenew password.
4. Confirm Password: Input the new password once again. Confirm password
must be the same as the New password. System will inform you "Change password
successfully!" while they are the same, or inform you to input the password of
Confirm password onceagain when theyare not thesame.
3.6 OSD Setting
1. Subtitle Display: Press
select between Onand Off.
2. OSD Timeout: Press
keys to
keys toselect
from 1 to10 by step1. The default values Is 5.
3. OSD Transparency: Press keys to
select among Off, 10%, 20%, 30%, 40%. The
default option isOff.
Press MENU or EXIT key to saveand exit.
3.7 Favorite
There are 32 favorites group listed in this
window. Press PR+, PR- keys to select one
and press OK key to the Rename window.
Since the same operation as the above the
Add Satellite window, here we don't explain
any more.
3.8 Other
1. LNB Power:Select between Off and On.
2. Channel Play Type: Select among All,
Free, Scramble.
3. Channel Change: Select between Freeze
and Black screen.
4. Beeper: Select between Off and On.
4. Tools
1. Press OK key or
key to pop up the
"Input Password" dialogue, you can not
enter into the menu unless the correct
password is inputted. The default password
is 0000.
2. Press PR+, PR- keys to move the cursor
up or down.
3. Press EXIT key or
key to move the
focus to theleft menu.
4.1 Information
Press OK key to the Information window.
4.2 Factory Setting
Press OK key to enter into the Factory
Setting window.
Select Yes button and press OK key to return
to the factory setting. All searched channels
and set information will be erased.
Select No button and press OK key to cancel
this operation, or press MENU or EXIT key to
cancel and exit.
4.3 SatcoDX Auto Programing
Press OK key at the Start button to start
receiving date from RS232 for 10 seconds.
5. Game
1. Press OK key or
key to enter into the
game.
2. Press PR+, PR- keys to move the cursor
up or down.
3. Press EXIT key or
key to move the
focus to the left menu.
4. Select the game that you want to play and
press OK key to enter into the window.
6. Hot Key
6.1 Info
Press INFO key to pop up the Info bar.
Press INFO key again to pop up the program
guide of the current program. You can press
keys to know the program guide of the
future 16 days.
6.2 EPG
Press EPG key to enter into the EPG window.
1. Press PR+, PR-,
keys to select up
or down, left or right.
2. Press red colour key to pop up the Time
Bar window. Press PR+, PR- keys to select
up or down, while press
left or right in the time bar.
keys to select
: Press OK key at this button to return to
the EPG window.
: Press OK key at this button to move the
cursor to the current time line.
: Press OK key to push the time forward
or backward by half an hour.
: Press OK key to push the time
forward or backward by half an hour.
: Press OK key to push the time
forward or backward by a day. From the
current day, you can switch among the
future 14 days in circle.
3. Detail Information: In the EPG window, press PR+, PR-
keys to select the
channel and program, and press OK key to know the detail information of the
current program.
4. Press green colour key to enter into the Timer window. You can add the current
program to the Timer. If 8 timers is already, system will inform "Timer is full!'.
6.3 Find
Press A-Z key on to pop up the Find window.
User numeric keys to enter into the character
and use the colour keys to realized the
corresponding operation.
6.4 Number
Use the numeric keys (0-9) to input the
number of the desired channel. If the inputted
number is beyond the valid channel number, system will "No such a channel" and
press OK key to close this message.
6.5 TV/RADIO
In normal mode, press TV/RADIO key to switch between TV mode and Radio mode.
6.6 Up/Down (ChannelChange)
Press PR+, PR- keys to change the channel up or down. If in the all satellites group,
you can select channel in all searched channels. If in the specific satellite, only can
select channel in the satellite group.
6.7 Left/Righ t(Volume+/-)
Press
keys to change the volume. Press
keys to decrease the volume by
step 1, while press
keys to add the volume by step1.
6.8 Mute
Press
key to close the volume. You can press
key once again to restore the
volume, or press
keys to open the volume.
6.9 Pause
During the viewing, you can press PAUSE key to stop the picture while the volume
continues. You can play the picture by pressing PAUSE key once again.
6.10 OK
1. During the viewing or listening, press OK
key to pop up the TV program list or the
Radio program list.
2. Press PR+, PR- keys to select the channel
up or down, and then press OK key to play
this channel in full-screen.
3. Press
keys to select the satellite.
4. Press MENU or EXIT key to close this
window.
26
6.11 Audio
1. Press
window.
2. Press
keys to enter into the Audio
keys to select among Left,
Right, Stereo, andMono.
3. Changing the audio mode is only
connected with the current channel, not all
the channels.
4. Press MENU or EXIT key to close this
window.
6.12 Recall
Press
key toswitch the current channel to theprevious channel.
6.13 FAV
1. Press FAV key to pop up the favourite
group window.
2. Press
keys to select the favorite
group. Press PR+, PR- keys to select the
channel up or down.. Press OK key at the
selected channel to view it in full-screen.
Press MENU or EXIT key to exit.
3. If there is no favorite channel, system will
inform " No FAV Channel!" when you press
FAV key.
6.14 Teletext
Press TXT key to open the teletext onthe screen. Ifthere is no teletext, system will
inform "No TeletextData". Press EXIT key to exit.
6.15 Zoom
1. Press ZOOM key to switch among Zoom*1, Zoom*2, Zoom*3, Zoom*4, Zoom*5,
Zoom*6, Zoom*8, Zoom*12, Zoom*16.
2. In zoom mode, press PR+, PR-
down.
keys to move the cursor up, left, right,
3. Press MENU or EXIT key to exit
Problem
Possible causes
What to do
The display onthe front
panel does notlight up.
Check that themain cable isplugged into
the power socket.
Main cable isnot connected.
No sound orpicture, but the
front panel showsred light.
The receiver is in standbymode.
Press the standbybutton.
The satellite dishis not pointingat the Adjust the dish. Check the signal
satellite.
level in theAntenna Setupmenu.
No sound orpicture.
Check the cableconnections, LNB and
other equipment connectedbetween the
LNB and thereceiver, oradjust the dish.
No signal orweak signal.
The satellite dishis not pointingat
the satellite.
Adjust the dish.
Connect a signalattenuator to theLNB
input.
Signal is toostrong.
Bad picture /blocking
error.
Satellite dish istoo small.
Change to alarger dish.
Change to anLNB with lowernoise
factor.
LNB noise factortoo high.
The LNB isfaulty.
Change the LNB.
The picture isnot
showed on thescreen,
when switching on.
Check the UHF channel fixed in your
system and tune the UHF channel
properly.
The system is connected by RF
leads.
There is interferenceon
your digital satellite
channels, an existing
terrestrial channel orvideo
signal.
The system isconnected by RF
leads and theoutput channel ofthe
receiver interferes withan existing
terrestrial channels orVideo signal.
Change the receiver output channel to
a more suitablechannel, or connectthe
system by SCARTleads.
Battery exhausted.
Change the batteries.
The RCU isnot working.
Aim RCU atthe receiver, or checkthat
nothing blocks thefront panel.
RCU is incorrectlyaimed.
Note : If you have tried all of the actions suggested above, without solving the
problem, please contact your dealer or service provider.
|
Alpine CDA 7878R User Manual
Canon VIXIA HF M31 User Manual
Clarion Car Stereo System DXZ646MP User Manual
Creative PC CAM 900 User Manual
Crown Boiler M600 User Manual
FujiFilm 16121789 User Manual
Hitachi DZMV350A User Manual
Huey Chiao HCS32 User Manual
JVC Camcorder LYT2340 002A M User Manual
JVC Everio GZ HM340U User Manual