MXD40
INSTALLATION/OWNERS MANUAL
AM/FM/CD Marine Receiver with Detach Face
MARINE
MXD40 INSTALLATION
Wiring Diagram
Antenna Connector
RCA Cable
(sold separately)
GRAY Rear Preamp Output
Connect to amplifier RCA Input
BLUE Remote Turn-On
Connect to amplifier or power
antenna. Insulate wire if not used.
AMP
BLACK Ground
Connect to
5 AMP
AGC Fuse
chassis ground.
YELLOW Memory
Connect to battery
circuit or constant
12 volt source.
0.5 AMP
AGC Fuse
FUSES
When replacing fuses,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage radio. The
MXD40 uses one .5 amp
AGC fuse (Ignition) and one
5 amp AGC fuse (Battery)
located in-line.
RED Accessory
Connect to existing ignition
circuit or switched 12 volt source.
Right Front
Gray/Black (-)
Gray (+)
Right Rear
Violet/Black (-)
Violet (+)
Left Front
White/Black (-)
White (+)
Left Rear
Green/Black (-)
Green (+)
3
MXD40 OPERATION
Control Locations
1
2
3
4
5
6
18 17 16
15
14
13
12
11
10
9
8
7
Release
Volume
Preset 6
Preset 5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Tune/Track Up
Band
Preset 4/CD Random
Preset 3/CD Repeat
Preset 2/CD Intro
Preset 1/CD Top
Audio
Bass Boost
Eject
Display
Play/Pause
Power
Auto Store/Preset Scan
Tune/Track Down
MARINE
The MXD40 Marine Receiver features UV resistant faceplate construction and clear-coated
circuit boards for long lasting protection against the elements in the marine environment.
Both chassis and mounting sleeve include an EDP (Electro-Deposit Plating) process for
increased corrosion resistance.
4
MXD40 OPERATION
General Operation
Faceplate Removal Press REL and pull away from the left side to remove.
To re-install, insert right side of faceplate first then push left
side to secure.
*For semi-permanent faceplate installation, remove trim ring and install
supplied Phillips head #1 screw through left side of mounting frame into
faceplate.
Power On/Off Press PWR to turn the unit on. Inserting a CD will turn the unit
on automatically. Press PWR to turn the unit off.
CD Mode Insert a CD or press
/
II to begin or resume playback.
l
Tuner Mode Press PWR or BAND to begin or resume tuner operation.
Bass Boost Press BASS to activate and deactivate bass boost curve.
Activating this feature will enhance the bass frequencies
when listening to music at low volumes.
Volume Adjust volume using VOL L or VOL L (00-39).
Display Press DISP to display the clock. The radio frequency (tuner
mode) or CD track/elapsed time (CD player mode) show by
default.
Set the Clock Press DISP to display the clock, then release. Press and
hold DISP then press TUNE
TUNE to adjust the minutes. Release DISP to save the
selected time.
to adjust the hours and
5
MXD40 OPERATION
General Operation
Reset
Press and hold for more than 2 seconds to RESET the unit
upon initial installation. The RESET button is located behind
the faceplate.
Audio
Press AUD to select between Volume (default), Bass, Treble,
Balance & Fader.
Bass
Treble
Press AUD until BA appears
Press VOL L or L to adjust
(6 maximum / -6 minimum)
Press AUD until TR appears
Press VOL L or L to adjust
(6 maximum / -6 minimum)
Balance
Fader
Press AUD until B appears
Press VOL L (LEFT) or L (RIGHT) to adjust
(BL 16/BR 16) B 00 represents equal balance.
Press AUD until F appears
Press VOL L (FRONT) or L (REAR) to adjust
(FF 16/FR 16) F 00 represents equal balance.
6
MXD40 OPERATION
Tuner Operation
Press TUNE
or
momentarily to seek the next
Seek Tuning
strong station.
Press TUNE
press TUNE
or
or
for more than 2 seconds, then
momentarily to move radio
Manual Tuning
frequency up or down one step at a time. Press and hold to
advance quickly. If tuning is not adjusted for 2 seconds, the
unit will return to seek tuning mode (default).
Press BAND to select between FM1, FM2, FM3 and AM1,
Band
AM2 bands.
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button for more than 2 seconds.
When stored, the preset number will appear in the display.
The station can be recalled anytime by pressing the
corresponding preset button.
Storing and Recalling Station
Presets
Press AS/PS for more than 2 seconds to automatically store
the six strongest stations in the current band.
Automatically Store Stations
Preset Scan
Press AS/PS for less than 2 seconds to scan presets 1-6 on
the current band, pausing for 5 seconds at each. Press
AS/PS again to cancel.
7
MXD40 OPERATION
CD Player Operation
With the label facing up, insert a standard 5" CD into the CD
Insert CD
slot. The CD will automatically begin playback.
Press the EJECT button to stop and eject the CD. The unit
Eject CD
will change to tuner mode.
Press TRACK
Press TRACK
to skip to the beginning of the next track.
to return to the beginning of the current
Track Select
track. Pressing TRACK
again skips to the beginning of
the previous track.
Press and hold TRACK
or TRACK
to fast forward
Fast Forward and Reverse
or reverse a track.
Press
Press
/
/
II to temporarily stop CD playback.
II again to resume playback.
Pause
Intro
l
l
Press INT to play the first 10 seconds of each track.
Press INT to cancel.
Press RPT to continuously repeat selected track.
Press RPT to cancel.
Repeat
Random
Press RDM to play all tracks in random order.
Press RDM again to cancel.
Press TOP to begin playback from track 1.
Top
Some CD-Rs may be incompatible with this unit, depending
on media type and recording method. This model does not
support CD-RWs.
CD-R Compatibility
8
MXD40 WARRANTY
Limited One-Year Warranty
This warranty gives you specific legal rights.
You may also have other rights which vary from
state to state.
What to do? If the product requires warranty
service, you must prepay the initial shipping
charges. DUAL will pay the return shipping
charges if the product is returned to an address
within the USA.
Namsung America Inc. warrants this product to
the original purchaser to be free from defects in
material and workmanship, under normal
conditions, for a period of one year from the date
of the original purchase.
Namsung America Inc.
Attn: Returns Center
21318 64th Ave. South
Kent, WA 98032 U.S.A.
Toll Free: 1-866-626-7863
Namsung America agrees, at our option, during
the warranty period, to repair any defect in
material or workmanship or to furnish an equal
new or renewed product in exchange without
charges, subject to verification of the defect or
malfunction and proof of the date of purchase.
Exclusion of Certain Damages: This warranty is
exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right, claim
or remedy in contract or tort, whether or not
arising from the company’s negligence, actual or
imputed. No person or representative is
authorized to assume for the company any other
liability in connection with the sale of this
product. In no event shall the company be liable
for indirect, incidental or consequential
damages.
During the One-Year Warranty Period: For One
Year from the date of purchase, your product will
be replaced with a new, renewed or comparable
product (whichever is deemed necessary) if it
becomes defective or inoperative. This is done
without charge to you. Replacement products
are warranted for the balance of the original
warranty period.
Who is covered? This warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A., in the 48
contiguous states ONLY.
What is covered? This warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect line
voltage, unauthorized repair or failure to follow
instructions supplied with the product, or
damage occurring during return shipment of the
product.
9
MXD40 OPERATION
Specifications
CD Player Signal-to-noise: >86dB
Frequency response: 20Hz-20kHz, 3dB
Channel separation @ 1kHz: >65dB
D/A converter: 16 Bit
FM Tuner Tuning range: 87.5MHz-107.9MHz
FM mono sensitivity: 12dBf
50dB quieting sensitivity (stereo): 16dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz, 3dB
AM Tuner Tuning range: 530kHz-1710kHz
AM sensitivity: 30uV
Frequency response: 80Hz-2kHz, 3dB
General Total system power: 100 Watts Peak
Power output: 25Wx4 @ 14.4 VDC
Power supply: 11-16 VDC, negative ground
Speaker output impedance: 4 ohms
Fuse: .5 amp fast blow AGC, 5 amp fast blow AGC
Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm)
Specifications subject to change without notice
10
MXD40 OPERATION
Troubleshooting
Problem
Cause
Action
Yellow wire not connected or incorrect voltage Check connections for proper voltage
Unit will not turn on
(no power)
Red wire not connected or incorrect voltage
Black wire not connected
Fuse blown
(11~16VDC)
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unit has power
(but no sound)
One or more speaker wires touching each
other or touching chassis ground
Insulate all bare speaker wires from
each other and chassis ground
Yellow or red wire touching chassis ground
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Check for pinched wire
Use fuse with correct rating
Unit blows fuses
Unit is not mounted correctly or backstrap is
not secure
Check mounting sleeve and backstrap
support
Excessive skipping
Physical defect in media (CD or CD-R)
High internal temperature
Load/Eject operation error
Focus adjustment error
Check media for scratches
Turn unit off for 1 hour
Press eject or RESET
Clean or replace media
Clean or replace media
Press eject or RESET
Press eject or RESET
Press eject or RESET
Clean or replace media
Error 1 appears on display
Error 2 appears on display
Error 3 appears on display
Error 4 appears on display
Error 6 appears on display
Error 7 appears on display
Error 8 appears on display
Error 9 appears on display
Tracking auto adjustment error
Sled operation error
Focus search operation error
CLV (PLL) operation error
TOC data read error
11
Namsung America Inc.
21318 64th Ave. South
Kent, WA 98032
Toll Free: 1-866-626-7863
©2003 Namsung America, Inc.
EVOK0603-V01
DMP65
INSTALLATION/OWNERS MANUAL
6.5" Dual Cone Marine Speakers
MARINE
DMP65 INSTALLATION
Preparation/Installation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal.
(consult a qualified technician for instructions)
• Use extreme caution when drilling holes to avoid damaging fuel lines,
hydraulic lines or existing wiring.
Getting Started
• Determine where the speakers will be mounted. Ensure an area large enough
for the speaker to mount evenly. Be sure the mounting location is deep enough
for the speaker to fit.
• Using an appropriate tool, cut a 5.13" diameter mounting hole. Route speaker wires
and connect to speakers, observing speaker polarity.
• Install speaker into opening using supplied hardware and test for correct operation.
TYPICAL MOUNTING METHOD
2
DMP65 WARRANTY
Limited One-Year Warranty
This warranty gives you specific legal rights. You may
also have other rights which vary from state to state.
What to do? If the product requires warranty service,
you must prepay the initial shipping charges. DUAL
will pay the return shipping charges if the product is
returned to an address within the USA.
Namsung America Inc. warrants this product to the
original purchaser to be free from defects in material
and workmanship, under normal conditions, for a
period of one year from the date of the original pur-
chase.
Namsung America Inc.
Attn: Returns Center
21318 64th Ave. South
Kent, WA 98032 U.S.A.
Toll Free: 1-866-626-7863
Namsung America agrees, at our option, during the
warranty period, to repair any defect in material or
workmanship or to furnish an equal new or renewed
product in exchange without charges, subject to veri-
fication of the defect or malfunction and proof of the
date of purchase.
Exclusion of Certain Damages: This warranty is
exclusive and in lieu of any and all other warranties,
expressed or implied, including without limitation the
implied warranties of merchantability and fitness for
a particular purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether or not
arising from the company’s negligence, actual or
imputed. No person or representative is authorized to
assume for the company any other liability in connec-
tion with the sale of this product. In no event shall the
company be liable for indirect, incidental or conse-
quential damages.
During the One-Year Warranty Period: For One Year
from the date of purchase, your product will be
replaced with a new, renewed or comparable product
(whichever is deemed necessary) if it becomes defec-
tive or inoperative. This is done without charge to
you. Replacement products are warranted for the
balance of the original warranty period.
Who is covered? This warranty is extended to the
original retail purchaser for products purchased and
used in the U.S.A., in the 48 contiguous states ONLY.
What is covered? This warranty covers all defects in
material and workmanship in this product. The fol-
lowing are not covered: installation/removal costs,
damage resulting from accident, misuse, abuse, neg-
lect, product modification, improper installation,
incorrect line voltage, unauthorized repair or failure to
follow instructions supplied with the product, or dam-
age occurring during return shipment of the product.
3
DMP65 SPECIFICATIONS
Specifications
7.13"
Outside Diameter
Mounting Depth
Mounting Height
Cut-out Diameter
Frequency Response
Sensitivity
2.5"
.88"
5.13"
45Hz-18kHz, 3dB
90dB 1W/1M
4 ohms
20 Watts
60 Watts
Impedance
RMS Power
Peak Power
Specifications subject to change without
notice
Namsung America Inc.
21318 64th Ave. South
Kent, WA 98032
Toll Free: 1-866-626-7863
©2003 Namsung America, Inc.
EVOK0603-V01
|