Owner’s manual
VXZ756
DVD/VCD/CD/WMA/MP3 Receiver/
CeNET Control
•
•
3
4
NTSC NTSC
PAL
PAL
2. PRECAUTIONS
1. When the inside of the car is very cold and
the player is used soon after switching on the
heater moisture may form on the disc or the
optical parts of the player and proper
naturally allowing normal operation.
2. Driving on extremely bumpy roads which
cause severe vibration may cause the sound
to skip.
playback may not be possible. If moisture
forms on the disc, wipe it off with a soft cloth.
If moisture forms on the optical parts of the
player, do not use the player for about one
hour. The condensation will disappear
3. This unit uses a precision mechanism. Even
in the event that trouble arises, never open
the case, disassemble the unit, or lubricate
the rotating parts.
CHANGES OR MODIFICATIONS NOT
EXPRESSLY APPROVED BY THE
MANUFACTURER FOR COMPLIANCE COULD
VOID THE USER’S AUTHORITY TO OPERATE
THE EQUIPMENT.
CAUTION
USE OF CONTROLS, ADJUSTMENTS, OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN, MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
INFORMATION FOR USERS:.
CHANGES OR MODIFICATIONS TO THIS
PRODUCT NOT APPROVED BY THE
MANUFACTURER WILL VOID THE
WARRANTY.
THE COMPACT DISC PLAYER and MINI DISC
PLAYER SHOULD NOT BE ADJUSTED OR
REPAIRED BY ANYONE EXCEPT PROPERLY
QUALIFIED SERVICE PERSONNEL.
Handling Compact Discs
Use only compact discs bearing the
mark.
Do not play heart-shaped, octagonal, or other specially
shaped compact discs.
Some CDs recorded in CD-R/CD-RW mode may not
be usable.
or
• To remove a compact disc from its storage case,
press down on the center of the case and lift the disc
out, holding it carefully by the edges.
• Do not use commercially available CD protection
sheets or discs equipped with stabilizers, etc. These
may damage the disc or cause breakdown of the
internal mechanism.
Handling
Storage
• Compared to ordinary music CDs, CD-R and CD-RW
discs are both easily affected by high temperature
and humidity and some of CD-R and CD-RW discs
may not be played. Therefore, do not leave them for
a long time in the car.
• Do not expose compact discs to direct sunlight or any
heat source.
• Do not expose compact discs to excess humidity or
dust.
• New discs may have some roughness around the
edges. If such discs are used, the player may not
work or the sound may skip. Use a ball-point pen or
the like to remove any roughness from the edge of
the disc.
• Do not expose compact discs to direct heat from
heaters.
Cleaning
• To remove fingermarks and dust, use a soft cloth and
wipe in a straight line from the center of the compact
disc to the circumference.
• Never stick labels on the
surface of the compact
disc or mark the surface
with a pencil or pen.
• Never play a compact
disc with any cellophane
tape or other glue on it
Ball-point pen
• Do not use any solvents, such as commercially
available cleaners, anti-static spray, or thinner to
clean compact discs.
• After using special compact disc cleaner, let the
compact disc dry off well before playing it.
Roughness
or with peeling off marks. If you try
to play such a compact disc, you may
not be able to get it back out of the CD
player or it may damage the CD player.
• Do not use compact discs that have large scratches,
are misshapen, cracked, etc. Use of such discs may
cause misoperation or damage.
VXZ756
3
3. DVD VIDEO SYSTEM
DVD video is a high-quality digital video source that provides crisp and clear images. One 12 cm disc
contains either one film or four hours of music.
● DVD Video Features
● About CD Extra discs
This unit provides the following functions in addition to the
high image quality and sound quality of DVD video.
Notes:
A CD Extra disc is a disc in which a total of two sessions have
been recorded. The first session is Audio session and the
second session Data session.
Your personally-created CDs with more than second data
sessions recorded cannot be played on this DVD video player.
• The functions described in the section, “Features”, for
example, the recorded language, subtitles, angles,
etc. differ with the DVD video disc. Refer to the
instructions provided with the DVD video.
• Some disc functions may operate differently than
described in this manual.
●
About playing a CD-R/CD-RW, DVD R/RW disc
This player can play CD-R/CD-RW, DVD R/RW discs
previously recorded in music CD format or video CD format.
● Discs that cannot be played back
This DVD video player cannot play back DVD-Audio, DVD-
RAM, Photo CDs, etc.
● Multi-sound function
DVD video can store up to 8 languages for one film; select
the language of your preference.
Notes:
• It may also not be possible to play back CDs recorded on a
CD-R unit and CD-RW unit. (Cause: disc characteristics,
cracks, dust/dirt, dust/dirt on player’s lens, etc.)
• The languages stored on the disc are
indicated by the icon as shown.
● Multi-angle function
A DVD video that is filmed from multiple angles
allows you to select the angle of choice.
• The number of recorded angles are indicated
by the icon as shown.
● Subpicture (subtitles) function
A DVD video can record subtitles for up to 32 languages and
you can select the language of the subtitles you wish to see.
• The number of recorded subtitle languages are
indicated by the icon as shown.
● Multi-story function
When a DVD video contains more than one story for a film,
you can select the story you wish to enjoy. The operation
procedures vary with the disc; observe the instructions for
selecting a story provided during playback.
● Dolby Digital
Dolby Digital enables up to 5.1 independent multi-channel
audio reproduction, the same type of surround system that is
also used in movie theaters.
2
•
If a CD-R or CD-RW disc that has not been finalized is
played, it will take a long time to start playing. Also, it may not
be possible to play depending on its recording conditions.
•
You cannot play Super Audio CDs. Playback of the CD
layer is not supported even if it is a hybrid disc.
● Note on region numbers
The DVD video system assigns a region number to DVD video
players and DVD discs by sales area.
2
This player can play “ALL” and “3” or “4” (and those inclusive).
For information checking on the recognition of “3” and “4”, see
page 34 “Country code list”. The DVD
3
4
ALL
3
4
video region number is marked
on the disc jacket as shown.
● TV color system
6
NTSC NTSC
PAL
PAL
This DVD player plays NTSC discs and PAL discs only and
cannot be used for playback of SECAM discs.
● About MP3/WMA playback
This unit can play back CD-R/CD-RW discs on which MP3/
WMA music data have been recorded. For a detailed
● DTS
DTS (Digital Theater System) is a sound system that differs
from the Dolby Digital system. DTS provides a larger amount
of data than Dolby Digital enabling high-quality surround
playback and incorporates a DTS-CD software for music like
a DVD software allows 5.1 channel independent multi-
channel audio reproduction.
information, see the page entitled “Listening to an MP3/WMA”.
About the registered marks etc.
• This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection
tecnology must be authorized by Macrovision Corporation,
and is intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
● Menu screens
Menus can be called up
Main Menu
during DVD video playback
to perform menu setting.
•
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic”, and the double-D symbol are trademarks of Dolby
Laboratories.
Discs
Playable disc
● Playable discs
• Manufactured under license from Digital Theater Systems,
Inc.U.S. Pat. No’s. 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535 and other U.S. and world-
wide patents issued and pending. “DTS” and “DTS Digital
Surround” are registered trademarks of Digital Theater
Systems, Inc. Copyright 1996, 2003 Digital Theater
Systems, Inc. All Rights Reserved.
DVD video discs
video CDs
This DVD video player can
play the following discs.
Note:
• When you play a CD
Extra disc, only the
first session will be
recognizesd.
Audio CDs
MP3 ID3 TAG
WMA
Be sure to unfold and read the next page. /
/
VXZ756
4
4. CONTROLS /
/
Source unit /
/
[Q]
IR-Receiver
[
]
Z+
[DVD/CD SLOT]
[
]
ROTARY
[
]
RELEASE
[
],
SCN
[MENU]
[
[
]
RPT
[PS/AS],[
]
]
RDM
[
]
DIRECT
[
P.LIST]
[
DN]
[a], [d]
[
]
UP
[
ADJ]
[
]
ISR
[
A-M]
[
]
TITLE
[
]
BND
[
SRC]
[
]
DISP
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
5
VXZ756
5. NOMENCLATURE
Note:
• Be sure to read this chapter referring to the front diagrams of chapter “4. CONTROLS” on page 5 (unfold).
Names of the Buttons and their Functions
[RELEASE] button
[DIRECT] buttons
• Deeply push in the button to unlock the DCP.
• Stores a station into memory or recalls it
directly while in the radio mode.
IR-Receiver
• Receiver for remote control unit. (Operating
range: 30˚ in all directions)
[P.LIST] button
• Press and hold for 1 second or longer to turn
on or off the play list mode. (MP3/WMA disc
only)
[ROTARY] knob
• Turn to adjust the volume.
• Performs various settings.
[UP], [DN] buttons
• Selects the folder while an MP3/WMA disc is
playing.
[DVD/CD SLOT]
• Ejects a disc loaded in the unit.
• Selects the play list while in the play list
mode.
[Q] button
[ISR] button (Instant station recall)
• Eject a disc when it is loaded into the unit.
• Recalls ISR radio station in memory.
• Press and hold for 2 seconds or longer:
Stores current station into ISR memory (radio
mode only).
[Z+] button
• Use the button to select one of the 4 types of
sound characteristics already stored in
memory. Press and hold for 1 second or
longer to return to “FLAT” the default value.
[TITLE] button
• Switches the titles.
• Press and hold for 1 second or longer to
input or scroll the title.
[SCN], [MENU] button
• Performs scan play for 10 seconds of each
track while in the DVD mode.
• Press and hold for 1 second or longer to
perform folder scan play while an MP3/WMA
disc is playing.
• The DVD menu is displayed while a DVD is
playing. Pressing and holding for 1 second or
longer also displays the DVD title screen.
• The VCD MENU is displayed while a Video
CD is playing (when PBC is ON).
[BND] button
• Switches the band.
• Press and hold for 1 second or longer to
switch seek or manual tuning.
• Returns to a first scene or track while in the
DVD mode.
[DISP] button
• Switches the display indication (main display,
clock display).
• Press and hold for 1 second or longer to
switch to the display adjust mode.
[RPT] button
• Repeats play while in the DVD mode.
• Press and hold for 1 second or longer to
perform folder repeat play while an MP3/
WMA disc is playing.
[SRC] button
• Press and hold for 1 second or longer to
repeat the title while a DVD is playing .
• Press to turn on the power.
• Press and hold for 1second or longer to turn
off the power.
• Switches the operation mode among the
radio mode, etc.
[RDM] button
• Performs random play while in the DVD
mode.
• Press and hold for 1 second or longer to
perform folder random play while an MP3/
WMA disc is playing.
[A-M] button
• Switches to the audio mode (CENTER-VOL,
SUB-WOOF VOL, BASS, TREBLE,
BALANCE, FADER, Z-Enhancer Plus).
• Press and hold for 1 second or longer to turn
on or off the MAGNA BASS EXTENED.
6
VXZ756
Names of the Buttons and their Functions
[ADJ] button
[PS/AS], [
] button
• Switches to the adjust mode.
• Press and hold for 1 second or longer to
display the setup main menu while in the
DVD mode.
• Plays or pauses a CD or DVD while in the
DVD mode.
• Press and hold for 1 second or longer in the
DVD mode to stop playback.
• Performs preset scan in the radio mode.
• Press and hold for 2 seconds or longer to
perform auto store in the radio mode.
• Confirms various settings.
[a] / [d] buttons
• Select a station while in the radio mode or
select a scene or a track while in the DVD
mode.
• These buttons are used to make various
settings.
• Press and hold for 1 second or longer to
switch the fast-forward/fast-rewind.
Major Button Operations When External Equipment is
Connected to This Unit
[a] / [d] buttons
●When the CD changer is con-
• Repeats or advances a track when listening
to a disc.
nected
∗ For details, see the section “CD changer
• Press and hold for 1 second or longer to
switch the fast-forward/fast-rewind.
Operations”.
[SCN] button
• Performs scan play for 10 seconds of each
track.
[
] button
• Plays or pauses a CD.
• Press and hold for 1 second or longer to
perform disc scan play.
● When the TV is connected
* For details, see the section “TV
Operations”.
[RPT] button
• Performs repeat play.
• Press and hold for 1 second or longer to
perform disc repeat play.
[DIRECT] buttons
• Stores a station into memory or recalls it
directly.
[RDM] button
• Performs random play.
• Press and hold for 1 second or longer to
perform disc random play.
[BND] button
• Switches the band.
• Press and hold for 1 second or longer to
switch seek or manual tuning.
[UP], [DN] buttons
• Selects the disc.
[ADJ] button
• Press and hold for 1 second or longer to
switch the TV picture mode or VTR (external)
picture mode.
[TITLE] button
• Switches the titles.
• Press and hold for 1 second or longer to
input or scroll the title.
[a] / [d] buttons
• Selects a station.
[BND] button
• Advances to next disc.
[PS/AS] button
• Performs preset scan in the TV mode.
• Press and hold for 2 seconds or longer to
perform auto store in the TV mode.
[DISP] button
• Switches the display indication (main display,
clock display).
VXZ756
7
Display Items
Z-Enhancer Plus indication
MAGNA BASS EXTEND indication
Operation status and function mode indication
Titles, clock, and the names of the mode being
selected etc. are displayed.
Playback time indication,
Frequency indication
Function indication
: Disc (folder) Scan etc.
: Scan indication
: Stereo indication
: Manual indication
: Mute indication
: MP3 indication
: WMA indication
: Repeat indication
: Random indication
: Reception band indication
: Track number indication
: Preset channel indication (1 to 6)
: Disc number indication (1 to 12)
LCD Screen
In extreme cold, the screen movement may slow down and the screen may darken, but this is normal.
The screen will recover when it returns to normal temperature.
8
VXZ756
6. DCP
The control panel can be detached to deter theft.
When detaching the control panel, store it in the
DCP (DETACHABLE CONTROL PANEL) case to
prevent scratches.
Attaching the DCP
1. Insert the DCP so that the A section on the
right side of the DCP catches on the hook B
on the unit.
We recommend taking the DCP with you when
leaving the car.
Removing the DCP
1. Press the [SRC] button for 1 second or
longer to switch off the power.
2. Press the [RELEASE] button deeply to open
the DCP.
[
]
RELEASE button
2. Press the left side C of the DCP carefully to
fit it in place.
3. Pull the DCP toward you and remove it.
CAUTION
• The DCP can easily be damaged by shocks.
After removing it, be careful not to drop it
or subject it to strong shocks.
DCP
• If the [RELEASE] button is pressed and the
DCP is not locked into place, it may fall out
from vibration of the car. This can break the
DCP, so after removing it, either install it on
the unit or put it in its DCP case.
• The connector connecting the unit and the
DCP is an extremely important part. Be
careful not to damage it by pressing on it
with fingernails, screwdrivers, etc.
Note:
• If the DCP is dirty, wipe off the dirt with a soft, dry
cloth only.
VXZ756
9
7. REMOTE CONTROL
Buttons Used in the DVD Mode
[MUTE]
[POWER][SRC]
[DISC UP][BND]
[VOLUME]
[P.TIME]
[DISP]
[0~9]
(Ten-key)
[
]
[SEARCH MODE]
[RTN]
[MENU]
[
] [ ] [ ] [
]
[ENT]
[SET UP]
[DVD TITLE]
[ISR]
[a ] [ d]
[PBC]
[RDM][TV/VTR]
[SCN] [PS/AS]
[RPT]
[SLOW]
[AUDIO]
[ANGLE]
[SUB TITLE]
[P.TIME] button
[
], [ ], [ ], [ ] buttons (cursor buttons)
Used to switch among play time displays
When selecting the menu items shown in the
monitor screen, use the cursor buttons to move
the cursor up and down, left and right.
[0-9] buttons (Ten-key buttons)
Used to input numbers.
[MENU] button
V-CD (with PBC):Displays the PBC menu.
DVD VIDEO:Displays the menu screen.
[RTN] button
Returns to the previous menu.
[ENT] button
Press this button to enter the setup item.
[DVD TITLE] button
DVD VIDEO:Displays the title screen.
[SET UP] button
Displays the setup screen of the unit.
10
VXZ756
Buttons Used in the DVD Mode
[PBC] button
Turns on/off the playback control (PBC) function
for V-CDs equipped with it.
[AUDIO] button
DVD VIDEO:Switches among languages for
audio (for DVDs with two or more languages).
V-CD:Switches among audio output methods.
Receiver for remote control unit
[SUB TITLE] button
Switches among languages for the subtitle.
Operationg range :
30° in all directions
Signal transmitter
[ANGLE] button
Switches among angles while in DVD playback.
(This button is available only on multiple angles
DVDs.)
[SLOW] button
While the button is kept pressed, slow play is
performed.
[SEARCH MODE] button
After this button is pressed, enter numbers using
Ten-key buttons.
DVD-VIDEO: Performs searching with a title/
chapter number.
MP3/WMA: FOLDER/TRACK number.
V-CD (key inputs are accepted only when the
PBC is turned off.):
TRACK number
CD: TRACK number.
Inserting the Batteries
1. Open the rear battery cover.
Rear cover
2. Insert the two supplied size AA (SUM-3, R6/
1.5V) batteries orienting the plus and minus
poles of the batteries as shown by the + and
- symbols inside the battery compartment.
Close the battery cover.
Notes:
Using batteries improperly can cause them to
explode. Take note of the following points:
• When replacing batteries, replace both batteries
with new ones.
• Do not short-circuit, disassemble or heat batteries.
• Do not dispose of batteries into fire or flames.
• Dispose of spent batteries properly.
VXZ756
11
Functions of the Remote Control Unit Buttons
Mode
DVD
(CD/MP3/WMA)
Radio
TV
CD changer
Button
Switches among radio, DVD (CD/MP3/WMA), CD changer, TV and AUX.
[SRC]
Plays the first track.
Top play.
Moves the next disc
in increasing order.
Switches reception
band.
Switches reception
band.
[DISC UP],
[BND]
[VOLUME]
Increases and decreases volume (in all modes).
[
] , [
]
Moves preset
channels up and
down.
Moves tracks up and down.
When pressed and held for 1 second:
Fast-forward/fast-rewind.
Moves preset
channels up and
down.
[
]
Switches between
playback and pause.
When pressed and
held for 1 second or
longer to stop play.
Switches between
playback and pause.
No function.
No function.
[MUTE]
Turns mute on and off.
[ISR]
Recalls ISR radio station in memory.
When pressed and held for 2 seconds or longer: Stores current station into ISR memory (radio
mode only).
[DISP]
Switches among main display and clock display.
When pressed and held for 1 second or longer : Switches the title (except in the radio and TV
mode).
[SCN],
[PS/AS]
Scan play.
Preset scan.
Preset scan.
Scan play.
When pressed and
held for 1 second or
longer:
When pressed and
held for 2 seconds or
longer:
When pressed and
held for 2 seconds or
longer:
When pressed and
held for 1 second or
longer:
Folder scan play
(MP3/WMA disc).
Auto store.
Auto store.
Disc scan play.
[RPT]
Repeat play.
No function.
No function.
Repeat play.
When pressed and
held for 1 second or
longer:
Folder repeat play
(MP3/WMA disc).
When pressed and
held for 1 second or
longer:
Disc repeat play.
[RDM],
[TV/VTR]
Random play.
Switches between TV
and VTR.
No function.
Random play.
When pressed and
held for 1 second or
longer:
When pressed and
held for 1 second or
longer:
Folder random play
(MP3/WMA disc).
Disc random play.
∗ Some of the corresponding buttons on the source unit and remote control unit have different functions.
12
VXZ756
8. OPERATIONS
Note: Be sure to read this chapter referring to the front diagrams
Basic Operations
of chapter “4. CONTROLS” on page 5 (unfold).
Selecting a mode
CAUTION
1. Press the [SRC] button to change the
Be sure to lower the volume before switching
off the unit power or the ignition key. The unit
remembers its last volume setting. If you
switch the power off with the volume up,
when you switch the power back on, the
sudden loud volume may hurt your hearing
and damage the unit.
operation source mode.
2. Each time you press the [SRC] button, the
operation mode changes in the following
order:
Radio mode ➜ DVD mode ➜
CD changer mode ➜ TV mode ➜
AUX mode ➜ Radio mode...
System check and speaker
setting
∗ External equipment not connected with
CeNET is not displayed.
During the initial power up of this unit, it will go
through a system check procedure.
Adjusting the volume
This procedure verifies any devices connected
through CeNET. Any additional CeNET devices
plugged into the unit after the initial power up will
initiate the system check procedure.
Turn the [ROTARY] knob to adjust the volume.
∗ The volume level is from 0 (minimum) to 33
(maximum).
When the power is turned on, “SYSTEM CHK”
appears in the display if the wire connections
were modified.
Switching the display
●When the power is turned on
Each time you press the [DISP] button, the
display switches in the following order:
The system check starts automatically within the
unit.
Main display ➜ Clock display ➜
Main display ...
When the system check is complete, “SP-
SETTING” appears in the display. Perform the
speaker setting.
∗ Once selected, the preferred display becomes
the display default. When a function
adjustment such as volume is made, the
screen will momentarily switch to that
function’s display, then revert back to the
preferred display several seconds after the
adjustment.
1. Turn the [ROTARY] knob to select the
speaker system.
∗ The factory default setting is “2ch”.
(Adjustment 2ch/5.1ch)
2. Press the [
] button.
∗ The setting is complete and the power
Setting the Z-Enhancer Plus
turns off.
This unit is provided with 4 types of sound tone
effects stored in memory. Select the one you
prefer.
Turning on/off the power
Note:
∗ This function cannot be adjusted when as follows:
“Pro Logic” is set to “ON”, the speaker system
is set to “5.1ch”, DVD/DTS-CD is being played.
∗ The factory default setting is “Z+ OFF”.
Each time you press the [Z+] button, the tone
effect changes in the following order:
• Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Press the [SRC] button.
“Z+ OFF” ➜ “BASS BOOST” ➜ “IMPACT” ➜
“EXCITE” ➜ “CUSTOM” ➜ “Z+ OFF”...
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
• BASS BOOST: bass emphasized
• IMPACT: bass and treble emphasized
• EXCITE: bass and treble emphasized, mid de-
emphasized
• CUSTOM: user custom
• Z+ OFF: no sound effect
3. Press and hold the [SRC] button for 1 second
or longer to turn off the power for the unit.
VXZ756
13
Basic Operations
Adjusting the Z-Enhancer Plus
Adjusting the center speaker
∗ This function cannot be adjusted when as
follows: “Pro Logic” is set to “ON”, the speaker
system is set to “5.1ch”, DVD/DTS-CD is being
played.
∗ This function cannot be adjusted when as
follows: “Pro Logic” is set to “ON”, the speaker
system is set to “5.1ch”, DVD/DTS-CD is being
played.
∗ This function cannot be adjusted when the
center speaker output is set to “OFF” or the
speaker system is set to “2ch”. For details on
how to set the center speaker, refer to the
subsection “Turning on/off speakers” in the
section “Changing Initial Settings such as
Menu Language, etc.”.
1. Press the [Z+] button and select the Z-
Enhancer Plus mode to adjust.
2. Press the [A-M] button and turn the
[ROTARY] knob to adjust the setting.
●When “B-BOOST 0” selected, you can
adjust the bass in the range of -3 to 3.
●When “IMPACT 0” selected, you can adjust
the bass and treble in the range of -3 to 3.
●When “EXCITE 0” selected, you can adjust
the bass and treble in the range of -3 to 3.
∗ When Z-Enhancer Plus is selected, press
and hold the [Z+] button for 1 second or
longer to change to the “CUSTOM” mode.
Bass/treble characteristics become flat and
the indication “Z+ FLAT” is shown in the
display.
∗ The factory default setting is “CTR-VOL 0”.
1. Press the [A-M] button and select “CTR-VOL
0”.
2. Turn the [ROTARY] knob to select from -4 to
+8 or OFF.
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the subwoofer
Adjusting the tone
∗ This function cannot be adjusted when as
follows: “Pro Logic” is set to “ON”, the speaker
system is set to “5.1ch”, DVD/DTS-CD is being
played.
∗ This function cannot be adjusted when as
follows: “Pro Logic” is set to “ON”, the speaker
system is set to “5.1ch”, DVD/DTS-CD is being
played.
∗ This function cannot be adjusted when the
subwoofer output is set to “OFF”. For details on
how to set the subwoofer, refer to the
subsection “Turning on/off speakers” in the
section “Changing Initial Settings such as
Menu Language, etc.”.
Press the [A-M] button and select the item to
adjust. Each time you press the [A-M] button, the
item changes as following order:
●When “BASS BOOST” is set
“CTR-VOL 0” ➜ “SW-VOL 0” ➜ “B-BOOST
0” ➜ “BAL 0” ➜ “FAD 0” ➜ Last function
mode.
∗ The factory default setting is “SW-VOL 0”.
1. Press the [A-M] button and select “SW-VOL 0”.
●When “IMPACT” is set
2. Turn the [ROTARY] knob to select from -6 to
“CTR-VOL 0” ➜ “SW-VOL 0” ➜ “IMPACT 0”
➜ “BAL 0” ➜ “FAD 0” ➜ Last function
mode.
+6 or OFF.
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
●When “EXCITE” is set
“CTR-VOL 0” ➜ “SW-VOL 0” ➜ “EXCITE 0”
➜ “BAL 0” ➜ “FAD 0” ➜ Last function
mode.
Adjusting the bass
●When “CUSTOM” is set
(Gain, Frequency, Q-curve)
“CTR-VOL 0” ➜ “SW-VOL 0” ➜ “BASS” ➜
“TREBLE” ➜ “BAL 0” ➜ “FAD 0” ➜ Last
function mode.
∗ This function cannot be adjusted when as
follows: “Pro Logic” is set to “ON”, the speaker
system is set to “5.1ch”, DVD/DTS-CD is being
played.
●When “Z+ OFF” is set
“CTR-VOL 0” ➜ “SW-VOL 0” ➜ “BAL 0” ➜
“FAD 0” ➜ Last function mode.
∗ “CTR-VOL” does not appear when the speaker
system is set to “2ch”.
∗ This adjustment can only be performed when
the Z-Enhancer Plus is set to “CUSTOM”.
1. Press the [A-M] button and select “BASS”.
∗ The display automatically returns to the
previous mode when no operation is
performed.
2. Turn the [ROTARY] knob to adjust the bass.
∗ The factory default setting is “BÅGAIN
0Γ. (Adjustment range: -6 to +6)
14
VXZ756
Basic Operations
3. Press the [a]/[d] button to select “B
ÅF
Adjusting the fader
60Γ.
∗ This function cannot be adjusted when as
follows: “Pro Logic” is set to “ON”, the speaker
system is set to “5.1ch”, DVD/DTS-CD is being
played.
Turn the [ROTARY] knob to select the
frequency.
∗ The factory default setting is “BÅF 60Γ.
(Adjustment 60/100/200 Hz)
1. Press the [A-M] button and select “FAD 0”.
4. Press the [a]/[d] button to select “BÅQ
1Γ.
2. Turn the [ROTARY] knob to adjust the
balance of the front and rear speakers.
∗ The factory default setting is “FAD 0”.
(Adjustment range: F12 to R12)
Turn the [ROTARY] knob to select the Q-
curve.
∗ The factory default setting is “BÅQ 1Γ.
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
(Adjustment 1/1.25/1.5/2)
5. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting MAGNA BASS
EXTEND
Adjusting the treble
(Gain, Frequency)
The MAGNA BASS EXTEND does not adjust the
low sound area like the normal sound adjustment
function, but emphasizes the deep bass sound
area to provide you with a dynamic sound.
∗ This function cannot be adjusted when as
follows: “Pro Logic” is set to “ON”, the speaker
system is set to “5.1ch”, DVD/DTS-CD is being
played.
∗ This function cannot be adjusted when as
follows: “Pro Logic” is set to “ON”, the speaker
system is set to “5.1ch”, DVD/DTS-CD is being
played.
∗ This adjustment can only be performed when
the Z-Enhancer Plus is set to “CUSTOM”.
1. Press the [A-M] button and select “TREBLE”.
∗ The factory default setting is “OFF”.
2. Turn the [ROTARY] knob to adjust the treble.
∗ The factory default setting is “TÅGAIN
0Γ. (Adjustment range: -6 to +6)
1. Press and hold the [A-M] button for 1 second
or longer to turn on the MAGNA BASS
EXTEND effect. “M-B EX” appears in the
display.
3. Press the [a]/[d] button to select “TÅF
15kΓ.
2. Press and hold the [A-M] button for 1 second
or longer to turn off the MAGNA BASS
EXTEND effect. “M-B EX” goes off from the
display.
Turn the [ROTARY] knob to select the
frequency.
∗ The factory default setting is “TÅF 15kΓ.
(Adjustment 10 kHz/15 kHz)
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the balance
∗ This function cannot be adjusted when as
follows: “Pro Logic” is set to “ON”, the speaker
system is set to “5.1ch”, DVD/DTS-CD is being
played.
1. Press the [A-M] button and select “BAL 0”.
2. Turn the [ROTARY] knob to adjust the
balance of the left and right speakers.
∗ The factory default setting is “BAL 0”.
(Adjustment range: L13 to R13)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
VXZ756
15
Radio Operations
Listening to the radio
Recalling a preset station
1. Press the [SRC] button and select the radio
A total of 24 preset positions (6-FM1, 6-FM2, 6-
FM3, 6-AM) exists to store individual radio sta-
tions in memory. Pressing the corresponding [DI-
RECT] button recalls the stored radio frequency
automatically.
mode. The frequency appears in the display.
2. Press the [BND] button and select the radio
band. Each time the button is pressed, the ra-
dio reception band changes in the following
order:
1. Press the [BND] button and select the desired
band (FM or AM).
FM1 ➜ FM2 ➜ FM3 ➜ AM ➜ FM1...
2. Press the corresponding [DIRECT] button to
3. Press the [a]/[d] button to tune in the de-
recall the stored station.
sired station.
∗ Press and hold one of the [DIRECT] buttons for
2 seconds or longer to store that station into
preset memory.
Tuning
There are 3 types of tuning modes available,
seek, manual and preset tuning.
Manual memory
1. Select the desired station with seek tuning,
manual tuning or preset tuning.
Seek tuning
1. Press the [BND] button and select the desired
2. Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store the current
station into preset memory.
band (FM or AM).
∗ If “MANU” is lit in the display, press and hold
the [BND] button for 1 second or longer.
“MANU” in the display goes off and seek tun-
ing is now available.
Auto store
Auto store is a function for storing up to 6 sta-
tions that are automatically tuned in sequentially.
If 6 receivable stations cannot be received, a pre-
viously stored station remains unoverwritten at
the memory position.
2. Press the [a] or [d] button to automatically
seek a station.
When the [d] button is pressed, the station
is sought in the direction of higher frequen-
cies; if the [a] button is pressed, the station
is sought in the direction of lower frequencies.
1. Press the [BND] button and select the desired
band (FM or AM).
Manual tuning
2. Press and hold the [PS/AS] button for 2 sec-
onds or longer. The stations with good recep-
tion are stored automatically to the preset
channels.
There are 2 ways available: Quick tuning and
step tuning.
When you are in the step tuning mode, the fre-
quency changes one step at a time. In the quick
tuning mode, you can quickly tune the desired
frequency.
Preset scan
Preset scan receives the stations stored in pre-
set memory in order. This function is useful when
searching for a desired station in memory.
1. Press the [BND] button and select the desired
band (FM or AM).
∗ If “MANU” is not lit in the display, press and
hold the [BND] button for 1 second or longer.
“MANU” is lit in the display and manual tuning
is now available.
1. Press the [PS/AS] button.
2. When a desired station is tuned in, press the
[PS/AS] button again to continue receiving
that station.
2. Tune into a station.
Note:
●Quick tuning:
• Be careful not to press and hold the [PS/AS] but-
ton for 2 seconds or longer, otherwise the auto
store function is engaged and the unit starts stor-
ing stations.
Press the [a]/[d] button for 1 second or
longer to tune in a station.
●Step tuning:
Press the [a]/[d] button to manually tune in
a station.
16
VXZ756
Radio Operations
DVD Operations
Instant station recall (ISR)
Disc-In-Play function
Instant station recall is a special radio preset that
instantly accesses a favorite radio station at a
touch of a button. The ISR function even
operates with the unit in other modes.
As long as the ignition key is turned to the ON or
ACC position, this function allows you to turn the
power to the unit and start playing the disc
automatically when the disc is inserted even if
the power is not turned on.
●ISR memory
1. Select the station that you wish to store in
ISR memory.
Loading a disc
Insert the disc into the DVD/CD insertion slot
with its labeled side facing up, then the disc will
start playing.
2. Press and hold the [ISR] button for 2 seconds
or longer.
●Recalling a station with ISR
In any mode, press the [ISR] button to turn on
the radio function and tune the selected radio
station. “ISR” appears in the display. Press the
[ISR] button again to return to the previous
mode.
For 5-inch
(12 cm) disc
For 3-inch
(8 cm) single disc
Notes:
• Never insert foreign objects into the DVD/CD
SLOT.
• If the disc is not inserted easily, there may be
another disc in the mechanism or the unit may
require service.
Loading 8 cm compact discs
∗ No adapter is required to play an 8 cm CD.
∗ Insert the 8 cm CD into the center of the
insertion slot.
Backup Eject function
Pressing the [Q] button ejects the disc even if
the power to the unit was not turned on.
Press the [Q] button, then the disc will be
ejected.
Note:
• If the ejected disc is left as it is, it will be reloaded
after 15 seconds. However, single CDs will not be
reloaded, so make sure to remove them.
CAUTION
• Do not try to put your hand or fingers in the
disc insertion slot. Also never insert foreign
objects into the slot.
• Do not insert discs where adhesive comes
out from cellophane tape or a rental CD
label, or discs with marks where cellophane
tape or rental CD labels were removed. It
may be impossible to extract these discs
from the unit and they may cause the unit
to break down.
VXZ756
17
DVD Operations
DVD-Video Operations
Listening to a disc already
loaded in the unit
Watching a DVD-Video
After inserting a disc, the play mode is
automatically engaged.
Press the [SRC] button to select the DVD mode.
• Button operation may not be allowed
depending on the story of the disc.
When the unit enters the DVD mode, play starts
automatically.
If there is no disc loaded, the indication “NO
DISC” appears in the display.
■ After the menu screen is displayed
For normal DVD-Video discs, the menu screen
appears.
After the menu screen is displayed, select an
item in the following operations and play it back.
Selecting the DVD menu
1. Press the [MENU] button during playback.
∗ The DVD menus appears.
The displayed contents may differ, depending
on the DVD software.
• Example showing menu display.
Main Menu
2. Select an item by pressing the [ ] and [ ]
buttons and press the [ENT] button to enter.
Otherwise, select an item with the ten-key
buttons on the remote control unit and press
the [ENT] button to enter.
∗ The video images of the selected item are
played back.
• Depending on the disc, items cannot be
selected with the ten-key buttons.
Stopping playback
Press and hold the [
] button for 1 second or
longer during playback.
∗ Playback stops.
■ To resume playback
• Press the [
] button, and playback resumes
from the scene where playback is stopped.
Pausing playback
Press the [
] button during playback.
∗ Playback pauses.
■ To resume playback
• Press the [
resumes.
] button, and playback
18
VXZ756
DVD-Video Operations
Slow playback
Searching with a chapter/title
number
Press and hold the [SLOW] button on the remote
control unit during playback, or press and hold
the [d] button during pause.
You can locate the beginning of the scene using
the chapter numbers or title numbers recorded
on the DVD-Video disc.
∗ While the button is being pressed, slow
playback continues at the speed 1/2 times the
normal playback.
• Slow playback cannot be performed in the
backward direction. In addition, audio cannot
be reproduced during slow playback.
∗ This function can only be used from the remote
control unit.
1. Press the [SEARCH MODE] button during
playback and select “[C**]”.
∗ Each time you press the button, you can
switch between title number input “[T**]”
and chapter number input “[C**]”.
• Title
Skipping a chapter (searching)
Chapter means a small segment to divide the
data area of the disc.
A large segment to divide the data area
of the disc.
• Chapter
A small segment to divide the data area
Press the Chapter up [a] button or Chapter
down [d] button during playback.
∗ Chapters are skipped, as many as the times
the button is pressed, and playback starts.
of the disc.
Current
2. Input the number of the title that you want to
play back with the ten-key buttons (0 to 9).
• To input the title number “12”, press “1” of
ten-key buttons and then “2”.
location
a
d
Chapter
Chapter
Chapter
Backward
direction
Playback
direction
Press “1”.
Press “2”.
• Press the [d] button, and playback starts
from the beginning of the next chapter.
• Press the [a] button, and playback starts
from the beginning of the current chapter.
When this button is pressed again within
about 2 seconds, playback starts from the
beginning of the previous chapter.
• The unit may return to the menu screen
when the [d] button or [a] button is
pressed.
3. Press the [ENT] button on the remote control
unit.
∗ Playback starts from the scene of the input
title number or chapter number.
• If the input title number does not exist or
searching with a title number is not
allowed, the following message appears to
invalidate the input.
Fast-forward and fast-rewind
Press and hold the Fast-forward [d] button or
Fast-rewind [a] button during playback.
∗ Press and hold the button, and the playback
speed becomes 4-time faster first and then 16-
time faster 3 seconds later. Release the button,
and the normal speed is restored.
• No audio is reproduced during fast-forward and
fast-rewind operation.
• The menu screen may appear when the button
is pressed.
VXZ756
19
DVD-Video Operations
Repeat playback
Switching among languages
This operation plays back chapters/titles
recorded on the DVD-Video repeatedly.
On discs in which two or more audios or audio
languages have been recorded, you can switch
among the audio languages during playback.
Press the [RPT] button for chapter repeat.
∗ This function can only be used from the remote
control unit.
Press and hold the [RPT] button for 1 second or
longer for title repeat.
Press the [AUDIO] button during playback.
∗ Each time you press the button, you can
switch among audio languages.
• Depending on the disc, up to 8 audios may
be recorded. For details, see the mark of
8
● Chapter repeat:
Plays back one chapter repeatedly.
● Title repeat:
Plays back all chapters within the title repeatedly.
the disc (
: Indicates that 8 audios
Press the [RPT] button again, and repeat
playback is turned off.
have been recorded).
• When the power is turned on or when the
disc is changed with a new one, the
language set at the time of factory
shipment is selected. If that language has
not been recorded, the language specified
on the disc is selected.
• Depending on the disc, switching may be
completely impossible or impossible on
some scenes.
Using the title menu
On DVD discs containing two or more titles, you
can select from the title menu for playback.
1. Press the [DVD TITLE] button on the remote
control unit or press and hold the [MENU]
button for 1 second or longer on this unit
during playback.
• It may take time to switch among audios.
∗ The title menu screen appears.
• Press the [MENU] button to return to the
scene before the title menu screen and
play the DVD.
• Depending on the disc, the title menu
cannot be called with [DVD TITLE] button.
Switching subtitles
On DVD discs in which two or more subtitle
languages have been recorded, you can switch
among the subtitle languages during playback.
∗ This function can only be used from the remote
2. Press the [ ], [ ], [ ], [ ] buttons or use
the ten-key buttons to select an item.
• Movement of the selected item with the
buttons differs depending on the disc.
Selection using the ten-key buttons also
differs depending on the disc.
control unit.
Press the [SUB TITLE] button during playback.
∗ Each time you press the button, you can
switch among subtitles.
• Depending on the disc, up to 32 kinds of
• Depending on the disc, items cannot be
selected with the ten-key buttons.
subtitles may be recorded. For details, see
8
the mark of the disc (
: Indicates that 8
kinds of subtitles have been recorded).
• Depending on the disc, switching may be
completely impossible or impossible on
some scenes.
3. Press the [ENT] button.
• It may take time to switch among subtitles.
● To turn off subtitles
Press the [SUB TITLE] button several times, and
subtitles are turned off.
In initial setting:
Off
Subtitle 1
Subtitle 2
Subtitle X
20
VXZ756
DVD-Video Operations
By pressing the button for 1 second or longer
while the playback status is displayed, you can
switch among time displays.
Switching angles
On DVD discs in which video images have been
recorded in two or more angles, you can switch
among the angles during playback.
∗ This function can only be used from the remote
control unit.
Press the [ANGLE] button during playback.
∗ Each time you press the button, you can
switch among angles.
• Depending on the disc, up to 9 angles may
be recorded. For details, see the mark of
the disc (
: Indicates multi-angle).
8
• Depending on the disc, angles may switch
smoothly or switch with a momentary still
image.
• Depending on the disc, switching may be
completely impossible or impossible on
some scenes.
TITLE ELAPSED
TITLE REMAIN
• It may take time to switch among angles.
• Depending on the disc, scenes recorded in
two or more angles may be played back.
CHAPTER ELAPSED
CHAPTER REMAIN
Displaying the playback
status
∗ This function can only be used from the remote
• TITLE ELAPSED:
control unit.
Elapsed time of the title
Press the [P.TIME] button during playback.
∗ Each time you press the button, you can
switch between display (ON) and non-display
(OFF) of the playback status.
• TITLE REMAIN:
Remaining time of the title
• CHAPTER ELAPSED:
Elapsed time of the chapter
Title number
• CHAPTER REMAIN:
Remaining time of the chapter
Chapter number
Playback time
•
Digital 3/2.1 (Example):
Displaying the currently audio format
Audio format
VXZ756
21
Watching a video CD (V-CD)
After inserting a disc, the play mode is
automatically engaged.
Pausing playback
Press the [
] button during playback.
• Button operation may not be allowed
depending on the story of the disc.
∗ Playback pauses.
■ To resume playback
■ After the menu screen is displayed
For V-CD discs equipped with the PBC (Play
Back Control) function, the menu screen
appears. After the menu screen is displayed,
select an item in the following operations and
play it back.
• Press the [
resumes.
] button, and playback
Slow playback
Press and hold the [SLOW] button on the remote
control unit during playback, or press and hold
the [d] button during pause.
Selecting the V-CD menu
(for V-CD discs with PBC)
This key does not function on some discs.
∗ While the button is being pressed, slow
playback continues at the speed 1/2 times the
normal playback.
• Slow playback cannot be performed in the
backward direction. In addition, audio cannot
be reproduced during slow playback.
1. Press the [MENU] button during playback.
∗ The V-CD menu appears.
The displayed contents may differ, depending
on the V-CD software.
Skipping a track (searching)
• Example showing menu display.
Press the TRACK up [d] / TRACK down [a]
button during playback.
∗ The track is skipped and playback starts.
Current
location
a
d
Track
Track
Track
The menu screen can be switched depending
on a disc being played.
Backward
direction
Playback
direction
2. Select an item with the ten-key buttons on
the remote control unit and press the [ENT]
button to enter.
• Press the [d] button, and playback starts
from the beginning of the next track.
• Press the [a] button, and playback starts
from the beginning of the current track. When
this button is pressed again within about 2
seconds, playback starts from the beginning of
the previous track.
∗ The video images of the selected item are
played back.
Stopping playback
Press and hold the [
] button for 1 second or
This operation cannot be performed on some
discs with PBC.
longer during playback.
∗ Playback stops.
■ To resume playback
When the PBC is turned on
• When the [
] button is pressed, the disc
plays from the beginning.
If the unit is CeNET connected and the
function is switched, the disc plays from the
beginning.
When the PBC is turned off
• Press the [
] button, and playback resumes
from the scene where playback is stopped.
22
VXZ756
Watching a video CD (V-CD)
Fast-forward and fast-rewind
Changing audio output
Press and hold the Fast-forward [d] button or
You can change the audio output method.
Fast-rewind [a] button during playback.
∗ This function can only be used from the remote
control unit.
∗ Press and hold the button, and the playback
speed becomes 4-time faster first and then 16-
time faster 3 seconds later. Release the button,
and the normal speed is restored.
• No audio is reproduced during fast-forward and
fast-rewind operation.
Press the [AUDIO] button during playback.
∗ Each time you press the button, you can
switch among audio output methods.
LR (Stereo)
• The unit may return to the menu screen when
the button is pressed.
LL (Left)
Searching with a track
number
This operation allows searching with the track
numbers recorded on the video CDs.
RR (Right)
∗ This function can only be used from the remote
control unit.
Scan playback
1. Press the [SEARCH MODE] button during
playback.
This operation scans and plays back all tracks on
the disc, the first 10 seconds for each.
2. Input the number of the track that you want to
play back with the ten-key buttons (0 to 9).
• To input the track number “12”, press “1” of
the ten-key buttons and then “2”.
Press the [SCN] button.
∗ Press the [SCN] button again, and scan
playback is turned off.
You cannot do this operation when PBC is ON
for a disc with PBC functions.
Press “1”.
Repeat playback
Press “2”.
This operation plays back one track recorded on
the video CD repeatedly.
Press the [RPT] button.
3. Press the [ENT] button on the remote control
unit.
∗ Press the [RPT] button again, and repeat
playback is turned off.
You cannot do this operation when PBC is ON
for a disc with PBC functions.
∗ Playback starts from the scene of the input
track number.
• If the input track number does not exist or
searching with a track number is not
allowed, the following message appears to
invalidate the input.
Random playback
This operation plays back all tracks on the disc in
no particular order.
Press the [RDM] button.
∗ Press the [RDM] button again, and random
You cannot do this operation when PBC is ON
for a disc with PBC functions.
playback is turned off.
You cannot do this operation when PBC is ON
for a disc with PBC functions.
VXZ756
23
Watching a video CD (V-CD)
Displaying the playback
status
On/off of Play Back Control
On video CDs equipped with Play Back Control
function, you can turn it on/off.
∗ This function can only be used from the remote
∗ This function can only be used from the remote
control unit.
control unit.
Press the [P.TIME] button during playback.
∗ Each time you press the button, you can
switch between display (ON) and non-
display (OFF) of the playback status.
Press the [PBC] button.
∗ Each time you press the button, you can
switch between on and off.
∗ When the PBC is turned on or off, the disc
plays from the beginning.
∗ The factory default setting of PBC is “ON”.
Playback control (PBC)
This control signal is recorded on a Video CD for
version 2.0 and used to control playback. Using
pre-recorded menu screens in the Video CD with
PBC, you can enjoy playback of software with a
simplified dialog function or software with search
function. You can also enjoy a still picture at high
or standard resolution.
• Even when display of the playback status is
OFF, you can display the playback status by
operating the button.
• Depending on the playback status or disc, the
following indication may appear.
When the PBC is turned on
The beginning of a disc is played each time the
PBC is turned on or off.
By pressing the button for 1 second or longer,
you can switch among time displays.
TRACK ELAPSED
TRACK REMAIN
∗
TOTAL ELAPSED
∗
TOTAL REMAIN
∗ Displayed when the PBC is “OFF”.
Note:
• Depending on some discs, the [P.TIME] indication
may not be displayed on some scenes. Also, it
may occur that the P.TIME operation does not
work. When this happens, the indication
“INVALID” will appear.
24
VXZ756
Listening to a CD
∗ This unit is a CD TEXT compatible model.
This unit supports the display of the DISC TITLE,
TRACK TITLE and ARTIST of the CD TEXT.
Skipping a track (searching)
Press the TRACK up [d]/ TRACK down [a]
buttons.
After inserting a disc, the play mode is
automatically engaged.
∗ Tracks are skipped, as many as the times
the button is pressed, and playback starts.
• Press the [d] button, and playback starts
from the beginning of the next track.
• Press the [a] button, and playback starts
from the beginning of the current track.
When this button is pressed again within
about 2 seconds, playback starts from the
beginning of the previous track.
• Example showing CD TEXT display.
Fast-forward and fast-rewind
Press and hold the Fast-forward [d] button or
Fast-rewind [a] button during playback.
∗ Press and hold the button, and the
playback speed becomes 4-time faster first
and then 8-time faster 3 seconds later.
Release the button, and the normal speed
is restored.
Note:
• This unit supports only CD TEXT in
alphanumerics. Also, some character data may not
be reproduced properly on the monitor.
Searching with a track
number
Top function
The top function resets the CD player to the first
track of the disc. Press the [BND] button to play
the first track (track No. 1) on the disc.
This operation allows searching using the track
numbers recorded on the CDs.
∗ This function can only be used from the remote
Pausing playback
control unit.
Press the [
] button during playback.
1. Press the [SEARCH MODE] button during
∗ Playback pauses.
playback.
■ To resume playback
2. Input the number of the track that you want to
play back with the ten-key buttons (0 to 9).
• To input the track number “12”, press “1” of
the ten-key buttons and then “2”.
• Press the [
] button again, and
playback resumes.
Displaying CD titles
This unit can display title data for CD-text disc
and user titles input with this unit.
Press “1”.
Each time you press the [TITLE] button, the title
changes in the following order:
Press “2”.
User title (disc) ➜ CD-text title (disc) ➜ Artist
name ➜ CD-text title (track) ➜ User title
(disc)...
3. Press the [ENT] button on the remote control
unit.
Note:
• If the CD playing is not a CD-text CD or no user
titld=(as been input, “NO TITLE” appears in the
display.
∗ Playback starts from the track of the input
track number.
• If the input track number does not exist or
searching with a track number is not
allowed, the following message appears to
invalidate the input.
VXZ756
25
Listening to a CD
Listening to an MP3/WMA
MP3/WMA
Scan playback
This operation scans and plays back all tracks
recorded on the disc, the first 10 seconds for
each.
What is MP3?
MP3 is an audio compression method and classi-
fied into audio layer 3 of MPEG standards. This
audio compression method has penetrated into
PC users and become a standard format.
Press the [SCN] button.
∗ Press the [SCN] button again, and scan
playback is turned off.
This MP3 features the original audio data com-
pression to about 10 percent of its initial size with
a high sound quality. This means about 10 music
CDs can be recorded on a CD-R disc or CD-RW
disc to allow a long listening time without having
to change CDs.
Repeat playback
This operation plays back tracks recorded on the
CD repeatedly.
Press the [RPT] button.
∗ Press the [RPT] button again, and repeat
playback is turned off.
What is WMA?
WMA is the abbreviation of Windows Media Au-
dio, an audio file format developed by Microsoft
Corporation.
Random playback
This operation plays back all tracks on the disc in
no particular order.
Notes:
∗ Searching track down is invalid during
random playback.
• This unit does not support a WMA file protected by
DRM (Digital Rights Management). Only files with
DRM turned OFF are played.
• Windows Media™, and the Windows ® logo are
trademarks, or registered trademarks of Microsoft
Corporation in the United States and/or other
countries.
Press the [RDM] button.
∗ Press the [RDM] button again, and random
playback is turned off.
Changing the display of the
playback status
●To disable DRM (Digital Rights Manage-
ment):
∗ This function can only be used from the remote
1. When using Windows Media Player 8, click
on TOOLS ➜ OPTIONS ➜ COPY MUSIC
tab, then under COPY SETTINGS, unclick the
check box for PROTECT CONTENT. Then,
reconstruct files.
control unit.
By pressing the [P.TIME] button for 1 second or
longer, you can switch among time displays.
2. When using Windows Media Player 9, click
on TOOLS ➜ OPTIONS ➜ MUSIC RECORD
tab, then under Recording settings, unclick
the Check box for RECORD PROTECTED
MUSIC. Then, reconstruct files.
Personally constructed WMA files are used at
your own responsibility.
Precautions when creating
MP3/WMA disc
● Usable sampling rates and bit rates:
1. MP3: Sampling rate 32 kHz-48 kHz,
Bit rate: 8 kbps-320 kbps / VBR
2. WMA: Bit rate 32 kbps-192 kbps
TRACK ELAPSED
TRACK REMAIN
TOTAL ELAPSED
TOTAL REMAIN
26
VXZ756
Listening to an MP3/WMA
● File extensions
After disc selection, the play mode is
1. Always add a file extension “.MP3” or “.WMA”
to MP3 or WMA file by using single byte let-
ters. If you add a file extension other than
specified or forget to add the file extension ,
the file cannot be played.
automatically engaged.
• Example showing WMA/ID3 Tag display.
2. Files without MP3/WMA data will be skipped
and cannot be played.
● Logical format (File system)
1. When writing MP3/WMA file on a CD-R disc or
CD-RW disc, please select “ISO9660 level 1, 2
or JOLIET or Romeo” as the writing software
format. Normal play may not be possible if the
disc is recorded on another format.
2. The folder name and file name can be dis-
played as the title during MP3/WMA play but
the title must be within 62 single byte ASCII
characters (including an extension).
Note:
• This unit supports only WMA/ID3 Tag information
in ASCII characters. Also, some character data
may not be reproduced properly on the monitor.
3. Do not affix a name to a file inside a folder
having the same name.
Top function
● Folder structure
1. A disc with a folder having more than 8 hierar-
chical levels will be impossible.
The top function resets the MP3/WMA player to
the first track of a folder being played. Press the
[BND] button to play the first track (track No. 1)
of a folder.
● Number of files or folders
1. Up to 999 files/255 folders can be played. But
if there are 999 files in one folder, other
folders cannot be played.
Pausing playback
Press the [
∗ Playback pauses.
■ To resume playback
] button during playback.
2. Tracks are played in the order that they were
recorded onto a disc. (Tracks might not
always be played in the order displayed on
the PC.)
• Press the [
] button again, and
playback resumes.
3. Some noise may occur depending on the
type of encoder software used while
recording.
4. In case of a track recorded at VBR
(variable bit rate), the display for the play
time of the track may be slightly different
from the actual play time.
Also, the recommended value of VBR
ranges from 64 kbps to 320 kbps.
5. Depending on the damage conditions of a
file, it may occur that the file is not played
and the next file is played instead.
Also, if the damage is in a severe
condition, play stops showing the “DISC
ERROR” display.
VXZ756
27
Listening to an MP3/WMA
Displaying MP3/WMA titles
Fast-forward and fast-rewind
This unit can display title data for MP3/WMA
disc.
Press and hold the Fast-forward [d] button or
Fast-rewind [a] button during playback.
∗ Press the button, and the playback speed
becomes 4-time faster first and then 8-time
faster 3 seconds later. Release the button,
and the normal speed is restored.
Each time you press the [TITLE] button, the title
changes in the following order:
Folder ➜ TRACK ➜ Album TAG ➜ Artist TAG
➜ Title TAG ➜ Folder...
Note:
Notes:
• Fast-rewind cannot be performed while WMA files
are being played.
• If MP3/WMA disc is not input TAG, “NO TAG” ap-
pears in the display.
• For MP3, supports ID3 Tags V2.4 / 2.3 / 2.2 / 1.1 /
1.0.
• Tag displays give priority to V2.4 / 2.3 / 2.2.
• In the case of album Tags for WMA, the informa-
tion written into the extension header is displayed.
• Only ASCII characters can be displayed in Tags.
Selecting a track on the
screen
∗ This function can only be used from the remote
control unit.
Select a desired file with the Cursor button (“
and “ ”) and press the [ENT] button.
∗ Play starts.
”
Skipping a track (searching)
Press the TRACK up [d] / TRACK down [a]
• Example showing FOLDER list display.
buttons.
∗ Tracks are skipped, as many as the times
the button is pressed, and playback starts.
• Press the [d] button, and playback starts
from the beginning of the next track.
• Press the [a] button, and playback starts
from the beginning of the current track.
When this button is pressed again within
about 2 seconds, playback starts from the
beginning of the previous track.
This operation skips the track over the folder.
Screen selection flow
Folder select
This function allows you to select a folder con-
taining MP3/WMA files and start playing from the
first track in the folder.
ID3 Tag display screen
∗ This function can only be used from the source
Press the
[RTN] button or
[MENU] button
FILE list display screen
unit.
Press the [DN] button to move to the previous
folder.
FOLDER list display screen
Press the [UP] button to move to the next folder.
∗ Press the [UP] button while in the final folder to
1 Select with the Cursor button (“ ” and “ ”)
shift to the first folder.
and determine with the [ENT] button.
∗ Folder without an MP3/WMA file is not select-
able.
2 In case of a file on which ID3 Tag information
data have been recorded...
If any cursor button input was not made for a
specified period of time after file selection,
ID3 Tag screen is displayed.
28
VXZ756
Listening to an MP3/WMA
Playback by selecting a folder Listening to one track
and track (Direct select mode) repeatedly
This operation allows searching using the folder
and track numbers recorded on the MP3/WMA
disc.
(Track repeat playback)
This operation plays back the track currently
being played back repeatedly.
∗ This function can only be used from the remote
control unit.
Press the [RPT] button.
■ To cancel track repeat playback
Press the [RPT] button again.
1. Press the [SEARCH MODE] button during
playback.
∗ Each time you press the button, you can
switch between “T000” for track number
input and “F000” for folder number input.
Listening to tracks in a folder
repeatedly
2. Input the number for the track or folder that
you want to play back with the ten-key
buttons (0 to 9).
(Folder repeat playback)
This operation plays back tracks in an MP3/WMA
folder repeatedly.
3. Press the [ENT] button on the remote control
unit.
When you select the folder number playback
Press and hold the [RPT] button for 1 second or
longer.
starts from Track 1 of the input folder number.
■ To cancel folder repeat playback
When you are searching for some other folder
and track while a file is being played, pressing
the [MENU] button will return to the file being
played.
Press the [RPT] button again.
Listening to tracks in a
random order
(Track random playback)
Searching a desired track
(Track scan playback)
This operation plays the tracks in the folder in a
random order.
This operation plays back all tracks recorded on
the disc, about 10 seconds for each.
Press the [RDM] button.
∗ Searching track down is invalid during
Press the [SCN] button.
∗ Scan playback starts from the next track.
■ To cancel track scan playback
random playback.
■ To cancel track random playback
Press the [RDM] button again.
Press the [SCN] button again.
Listening to tracks in a
random order
Searching for a desired folder
(Folder scan playback)
(Folder random playback)
This operation plays back the first tracks of all
folders on the MP3/WMA disc, about 10 seconds
for each.
This operation plays back tracks recorded on the
disc in no particular order.
Press and hold the [RDM] button for 1 second or
longer.
Press and hold the [SCN] button for 1 second or
longer.
∗ Scan playback starts from the first track of
the next folder to the one currently being
played back.
■ To cancel folder random playback
Press the [RDM] button again.
■ To cancel folder scan playback
Press the [SCN] button again.
VXZ756
29
Listening to an MP3/WMA
Play list mode
This function allows you to play tracks, up to lat-
est 5 time stamps, by reading the play list infor-
mation written on the disc.
Changing the display of the
playback status
∗ This function can only be used from the remote
control unit.
∗ This function can only be used from the source
By pressing the [P.TIME] button for 1 second or
longer, you can switch among time displays.
unit.
1. Press and hold the [P.LIST] button for 1 sec-
ond or longer to turn on or off the play list
mode.
∗ Play list play is possible only when there is a
file whose extension is “.M3U” on the CD-R/
RW.
∗ Up to 5 play lists can be recognized, and up to
255 files can be recognized per play list.
2. Press the [DN] button to move to the previous
play list.
Press the [UP] button to move to the next play
list.
Notes:
TRACK ELAPSED
TRACK REMAIN
• The SCN/RPT/RDM functions cannot be used
while in the play list mode.
• The title changes from folder name to play list
name.
Making a play list
1. Write desired tracks to a CD-R/RW, etc. Be
sure to use ASCII characters for all file
names.
2. Make a play list by using a multimedia player,
etc. and save the data. The file format must
be M3U.
3. Again, write this play list to the CD-R/RW, etc.
Notes:
• When writing to a CD-R/RW, etc., be sure to use
ASCII characters.
• Up to 5 layers can be recognized as a list. For writ-
ten play lists, latest 5 lists are recognized in the or-
der in which they are written.
• When writing to a CD-R/RW, etc., turn off the Disc
At Once function.
• When adding a play list, it is recommended to
write it in the “Root” folder.
30
VXZ756
Changing Initial Settings such as Menu Language, etc.
(Main menu)
Selecting the monitor menu
Notes:
• The setup main menu appears only while in the
DVD mode.
• “PREFERENCES” appears only when there is no
disc loaded and playback stops.
• “AUDIO SETUP” appears only when the speaker
system is set to “5.1ch”.
Source unit Remote control
Source unit Remote control
• Menu settings described in this section are
displayed on the monitor.
If the set language has not been recorded on the
disc, the language specified on the disc is used for
display.
(Sub menu)
1. Press the [SET UP] button on the remote
control unit or press and hold the [ADJ]
button on the unit for 1 second or longer in
the DVD mode to display the main menu.
2. Select “GENERAL SETUP”,
Source unit Remote control
“PREFERENCES”, or “AUDIO SETUP” with
the “ ” or “ ” button and press the [ENT] to
enter.
Source unit Remote control
3. Press the “ ” or “ ” button to select the left
menu item.
4. Press the “ ” button to go to the option list.
5. Press the “ ” button to go to back to the left
menu item.
6. Press the [RTN] button to display the main
menu.
7. Press the [SET UP] button on the remote
control unit or press the [ADJ] button on the
unit to return to the original mode from the
setup mode engaged.
VXZ756
31
Changing Initial Settings such as Menu Language, etc.
● When watching through a wide TV monitor
Setting up the screen size
(16:9)
Set up the screen size according to the TV
monitor to which the unit is connected.
• WIDE:
∗ The factory default setting is “NORMAL/PS”.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “TV DISPLAY” from
“GENERAL SETUP”, and press the “
”
button to go to the option list.
3. Press the [ENT] button to enter.
Setting up the TV type
Set the TV type to NTSC, PAL, MULTI.
∗ The factory default setting is “PAL” or “MULTI”.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “TV TYPE” from
“GENERAL SETUP”, and press the “
”
button to go to the option list.
2. Press the “ ” or “ ” button to select a
screen size.
∗ The color of the selected item changes.
● When watching through a conventional TV
monitor (4:3)
• NORMAL/PS : The leftmost and rightmost
areas of the screen are cut off.
2. Press the “ ” or “ ” button to select “MULTI”,
“NTSC” or “PAL”.
3. Press the [ENT] button.
This function allows displaying the important
part of image fully on the screen. In some
cases, image is displayed while being
panned (scrolled).
• This setting can also be changed in the
Adjust Mode. Refer to the subsection
“Setting up the TV type” in the section “TV
Operations” for details.
• NORMAL/LB : A black zone is created in the
top and bottom areas of the screen.
Setting up the angle mark
display
You can set up so that the angle mark appears
on scenes where the angles can be switched.
∗ The factory default setting is “ON”.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “ANGLE MARK” from
This method displays Cinema Scope and
Vista Vision images without cutting them off
by creating a black zone on the top and
bottom gaps.
“GENERAL SETUP”, and press the “
”
button to go to the option list.
32
VXZ756
Changing Initial Settings such as Menu Language, etc.
Setting up the subtitle
language
∗ The factory default setting is “OFF”.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “SUBTITLE” from
“PREFERENCES”, and press the “ ” button
to go to the option list.
2. Press the “ ” or “ ” button to select “ON” or
“OFF”.
3. Press the [ENT] button.
Setting up the audio language
∗ The factory default setting is “ENGLISH”.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “AUDIO” from
“PREFERENCES”, and press the “ ” button
to go to the option list.
2. Press the “ ” or “ ” button to select a
language to be used.
Languages SELECT in the order:
ENGLISH
FRENCH
SPANISH
CHINESE
JAPANESE
OFF
2. Press the “ ” or “ ” button to select a
language to be used.
3. Press the [ENT] button.
Languages SELECT in the order:
Setting up the disc menu
language
ENGLISH
∗ The factory default setting is “ENGLISH”.
FRENCH
SPANISH
CHINESE
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “DISC MENU” from
“PREFERENCES”, and press the “ ” button
to go to the option list.
JAPANESE
3. Press the [ENT] button.
VXZ756
33
Changing Initial Settings such as Menu Language, etc.
2. Press the “ ” or “ ” button to select a
language to be used.
■ Country code list
Country
Input code
Languages SELECT in the order:
ENGLISH
Region number 3
BRUNEI DARUSSALAM
Kingdom of Cambodia
INDONESIA
KOREA, DEMOCRATIC PEOPLE’S REPUBLIC OF
KOREA,REPUBLIC OF
LAO PEOPLE’S DEMOCRATIC REPUBLIC
MALAYSIA
MYANMAR
PHILIPPINES
SINGAPORE
6678
7572
7368
7580
7582
7665
7789
7777
8072
8371
FRENCH
SPANISH
CHINESE
JAPANESE
3. Press the [ENT] button.
Setting up the country code
THAILAND
VIET NAM
EAST TIMOR
HONG KONG
MACAU
8472
8678
8480
7275
7779
8487
Set up the country number for setting up of the
parental level.
∗ The default setting is “8583” (US).
TAIWAN, PROVINCE OF CHINA
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “LOCALE” from
“PREFERENCES”, and press the “ ” button
to go to the option list.
Region number 4
ANTIGUA AND BARBUDA
ARGENTINA
AUSTRALIA
BAHAMAS
BARBADOS
BELIZE
BOLIVIA
6571
6582
6585
6683
6666
6690
6679
6682
6776
6779
BRAZIL
CHILE
COLOMBIA
COSTA RICA
CUBA
6782
6785
6877
6879
6967
8386
7074
7168
7184
7189
DOMINICA
DOMINICAN REPUBLIC
ECUADOR
EL SALVADOR
FIJI
GRENADA
GUATEMALA
GUYANA
2. Press the [ENT] button to display the input
screen.
3. Press the ten-key buttons to input a 4-digit
country number.
4. Press the [ENT] button.
HAITI
HONDURAS
JAMAICA
KIRIBATI
MARSHALL ISLANDS
MEXICO
7284
7278
7477
7573
7772
7788
34
VXZ756
Changing Initial Settings such as Menu Language, etc.
Setting up the parental level
You can change the level of parental lock (audio-
visual restriction).
Country
Input code
MICRONESIA, FEDERATED STATES OF
NAURU
NEW ZEALAND
7077
7882
7890
7873
This function allows cutting scenes that are
unfavorable for children or replacing them
automatically with other scenes prepared in
advance. For example, by replacing scenes of
radical violence or portrayals of sex with safe
scenes, you can make a trouble-free story as if it
were so from the beginning.
NICARAGUA
PALAU
PANAMA
PAPUA NEW GUINEA
PARAGUAY
PERU
SAINT KITTS AND NEVIS
SAINT LUCIA
SAINT VINCENT AND THE GRENADINES
SAMOA
8087
8065
8071
8089
8069
7578
7667
8667
8783
8366
∗ The factory default setting is level “8”.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “PARENTAL” from
“PREFERENCES”, and press the “ ” button
to go to the option list.
SOLOMON ISLANDS
SURINAME
TONGA
TRINIDAD AND TOBAGO
TUVALU
URUGUAY
VANUATU
VENEZUELA
ANGUILLA
ARUBA
VIRGIN ISLANDS (BRITISH)
8382
8479
8484
8486
8589
8689
8669
6573
6587
8671
CAYMAN ISLAND
7589
6789
6767
6775
7075
7170
8070
7180
7185
7781
2. Press the “ ” or “ ” button to select a
parental level.
CHRISTMAS ISLAND
COCOS (KEELING) ISLANDS
COOK ISLANDS
FALKLAND ISLANDS (MALVINAS)
FRENCH GUIANA
FRENCH POLYNESIA
GUADELOUPE
You can select from 1 to 8 or NO PARENTAL.
3. Press the [ENT] button to display the
PASSWORD VERIFICATION screen.
GUAM
MARTINIQUE
MONTSERRAT
7783
6578
7867
7885
7870
7780
8078
8475
8467
8770
NETHERLANDS ANTILLES
NEW CALEDONIA
NIUE
NORFOLK ISLAND
NORTHERN MARIANA ISLANDS
PITCAIRN
TOKELAU
TURKS AND CAICOS ISLANDS
WALLIS AND FUTUNA ISLANDS
4. Press the ten-key buttons to input a 4-digit
password.
∗ Factory default setting is “0000”.
VXZ756
35
Changing Initial Settings such as Menu Language, etc.
Setting up the password for
setting up of the parental level
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “PASSWORD” from
“PREFERENCES”, and press the “ ” button
to go to the option list.
Turning on/off speakers
You can turn on/off or select the size of front
speakers, a center speaker, surround speakers,
and a subwoofer depending on your speaker
system.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “SP-SEL” from
“AUDIO SETUP”.
2. Press the [ENT] button to display the
PASSWORD CHANGE screen.
2. Press the [ENT] button to display the SP-SEL
screen.
3. Input an old password.
4. Input a new password.
5. Input a confirm password.
Each time you press the [ENT] button, the setting
item changes as following order:
It is recommended that you take down a
memo about the password and keep it safely
to avoid forgetting it.
If you forget your password, you can set a
new password by entering [4356] as the OLD
PASSWORD.
SP-SEL
FRONT-SP
CENTER-SP
SRD-SP
Note:
When a disc with view limited is played
SUB-WOOFER
• When a disc with view limited is played, the
input screen requiring you to input the password
may appear. When this happens, enter the
correct password, otherwise play does not start.
36
VXZ756
Changing Initial Settings such as Menu Language, etc.
3. Press the “ ” button to go to the option list
Setting the speaker gain
and press “ ” or “ ” buttons to select the
setting.
You can select the settings as shown in the
following table.
∗ If you select “OFF” for this function, you cannot
adjust the speaker gain.
∗ This function appears only when there is no
disc loaded or playback stops.
∗ The factory default setting is “OFF”.
FRONT-SP
LARGE ∗
SMALL
SMALL ∗
OFF
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “SP-GAIN SET” from
“AUDIO SETUP”, and press the “ ” button
to go to the option list.
(Front speaker)
CENTER-SP
(Center speaker)
SRD-SP
LARGE ∗
SMALL
OFF
(Surround speaker)
SUB-WOOFER
(Subwoofer)
ON ∗
OFF
Asterisk (∗) indicates the factory default setting.
When you select “SMALL” for FRONT-SP,
setting for other speakers is subject to following
restriction.
• SRD-SP cannot be set to “LARGE”.
• SUB-WOOFER cannot be set to “OFF”.
• Only the following 4 patterns are available.
2. Press “ ” or “ ” buttons to select “ON” or
“OFF”.
3. Press the [ENT] button.
SUB-
WOOFER
FRONT-SP CENTER-SP
SRD-SP
Adjusting the speaker gain
SMALL
SMALL
SMALL
SMALL
SMALL
SMALL
OFF
SMALL
OFF
ON
ON
∗ This function cannot be operated when the disc
is loaded or when “SP-GAIN SET” is set to
“OFF”.
SMALL
OFF
ON
∗ You cannot adjust the speaker gain for
speakers set to “OFF” in “SP-SEL”.
∗ The factory default setting is “0 dB”.
OFF
ON
4. Press the [ENT] button.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “SP-GAIN” from
“AUDIO SETUP”.
5. Press the “ ” button to go back to the left
pane.
6. Repeat steps 2 to 4 to turn on/off each
speaker.
VXZ756
37
Changing Initial Settings such as Menu Language, etc.
2. Press the [ENT] button to display the SP-
Adjusting the speaker delay
time
GAIN screen.
The time necessary for sound to travel from
speakers to a listener differs depending on the
speaker location or the car size. By adjusting the
delay time of each speaker, you can hear the
sound from the front speakers and the other
speakers simultaneously.
∗ This function cannot be operated when
CENTER-SP and SRD-SP are set to “OFF” in
“SP-SEL”.
∗ The factory default setting is “0 ms”.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “DELAY” from
“AUDIO SETUP”.
3. Press “ ” or “ ” buttons to select the
speaker.
Each time you press the buttons, you can switch
among speakers.
FRONT L
CENTER
FRONT R
SRD L
SRD R
2. Press the [ENT] button to display the DELAY
SUB-WOOFER
screen.
The test tone is output from the speaker you
select.
4. Press “ ” button to go to the right pane.
5. Press “ ” or “ ” buttons to adjust the
speaker gain. The gain level ranges from “-
6dB” to “+6dB”.
6. Press the “ ” button to go back to the left
pane.
7. Repeat steps 3 to 5 to adjust the each
speaker gain.
Note:
3. Press “ ” or “ ” buttons to select the item.
• The test tone will not be output when DVD or CD
is being played with mute ON.
In that case, press the [MUTE] button on the
remote control unit to cancel the mute, or adjust
the volume.
Each time you press the buttons, you can switch
between center and surround speakers.
CENTER-SP
SRD-SP
4. Press “ ” button to go to the right pane.
5. Press “ ” or “ ” buttons to adjust the delay
time. The delay time ranges from “0 ms” to “5
ms” when you select “CENTER-SP” (1ms
step), or “0ms” to “15ms” when you select
“SRD-SP” (3ms step).
38
VXZ756
Changing Initial Settings such as Menu Language, etc.
6. Press the [ENT] button.
Setting the down mix
∗ This function can be operated only when the
Adjusting the dynamic range
speakers other than FRONT-SP are set to
“OFF” in “SP-SEL”.
This function allows you to select the method of
down-mixing when the channel format and the
output channel configuration are not in
agreement.
This function allows you to adjust the dynamic
range, the ratio of the loudest sounds to the
quietest sounds.
∗ The factory default setting is “MAX”.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “DRC” from “AUDIO
SETUP”.
∗ The factory default setting is “Lo/Ro”.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “DOWN MIX” from
“AUDIO SETUP”.
2. Press “ ” button to go to the right pane.
3. Press “ ” or “ ” buttons to select the setting.
You can select the dynamic range from
“MIN”, “STD”, or “MAX”.
2. Press “ ” button to go to the right pane.
3. Press “ ” or “ ” buttons to select “Lo/Ro” or
“Lt/Rt”.
4. Press the [ENT] button.
“Lo/Ro”: Down-mixing the discrete 5-channel
master etc. to 2-channel stereo track
“Lt/Rt”: Writing down matrix-encoded sounds
to 2-channel stereo track
Setting the Dolby Pro Logic
Decode processing
You can set whether or not 2-channel source is
processed using Dolby Pro Logic Decode.
4. Press the [ENT] button.
∗ The factory default setting is “ON”.
1. Following the steps 1 to 3 in “Selecting the
monitor menu”, select “Dolby PL” from
“AUDIO SETUP”.
2. Press “ ” button to go to the right pane.
3. Press “ ” or “ ” buttons to select “ON” or
“OFF”.
4. Press the [ENT] button.
VXZ756
39
Common Operations
Display Adjust Mode
Setting the clock
1. Press and hold the [DISP] button for 1
second or longer to switch to the display
adjust mode.
Entering MESSAGE
INFORMATION
When “MESSAGE” is selected for the screen
saver setting, you can change the contents of the
message.
∗ Up to 30 characters can be entered.
∗ The factory default setting is “Welcome to Clarion”.
1. Press and hold the [DISP] button for 1 second
2. Press the [a]/[d] button to select “CLOCK
E”.
3. Press the [
] button.
or longer to switch to the display adjust mode.
4. Press the [a]/[d] button to select the hour
2. Press the [a]/[d] button to select
or the minute.
“MSG INPUT E”.
5. Turn the [ROTARY] knob to set the correct
time.
3. Press the [
] button.
4. Press the [a]/[d] button to move the cursor.
5. Press the [BND] button to select a character.
Each time you press the [BND] button, the
character changes in the following orders:
∗ The clock is displayed in 12-hour format.
6. Press the [
memory.
] button to store the time into
7. Press the [DISP] button to return to the
Capital letters ➜ Small letters ➜ Numbers
and Symbols ➜ Umlaut ➜ Capital letters…
previous mode.
Note:
6. Turn the [ROTARY] knob to select the desired
• You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the car’s
battery or take out this unit, the clock is reset.
While setting the clock, if another button or
operation is selected, the clock set mode is
canceled.
character.
7. Repeat steps 4 to 6 to enter up to 30
characters for message.
8. Press and hold the [
] button for 2 seconds or
longer to store the message in memory and
return to the display adjust mode.
Turning the screen saver
function on or off
∗ Press and hold the [BND] button for 1 second or
longer to delete the message. Then press and
hold the [
] button for 2 seconds or longer to
This unit features various screen saver patterns
that are exhibited across the display. If the screen
savers are not desired, they can be turned off.
return the message to the default setting.
9. Press the [DISP] button to return to the
previous mode.
If the button operation is performed with the
screen saver function on, the operation display
corresponding to the button operation is shown
for about 30 seconds and the display returns to
the screen saver display.
Setting the method for title
scroll
Set how to scroll in CD-TEXT, MP3/WMA TITLE.
∗ The factory default setting is “ON”.
∗ The factory default setting is “ON”.
1. Press and hold the [DISP] button for 1 second
1. Press and hold the [DISP] button for 1 second
or longer to switch to the display adjust mode.
or longer to switch to the display adjust mode.
2. Press the [a]/[d] button to select
2. Press the [a]/[d] button to select “AUTO
“SCREEN SVR”.
SCROL”.
3. Turn the [ROTARY] knob to select the setting.
Each time you turn the [ROTARY] knob, the
setting changes in the following order:
OFF ➜ ON ➜ MESSAGE
3. Turn the [ROTARY] knob to select “ON” or
“OFF”.
● ON:
Scrolls automatically.
● OFF:
Scrolls just 1 time when the title was changed
or you press and hold the [TITLE] button for 1
second or longer.
4. Press the [DISP] button to return to the previ-
ous mode.
4. Press the [DISP] button to return to the
previous mode.
40
VXZ756
Common Operations
Dimmer control
You can set the dimmer control.
∗ The factory default setting is “ON”.
Setting the amplifier bypass
circuit
∗ The factory default setting is “OFF”.
1. Press and hold the [DISP] button for 1 second
1. Press the [ADJ] button to switch to the adjust
or longer to switch to the display adjust mode.
mode.
2. Press the [a]/[d] button to select
2. Press the [a]/[d] button to select “AMP
“DIMMER”.
CANCEL”.
3. Turn the [ROTARY] knob to select “ON” or
3. Turn the [ROTARY] knob to select “ON” or
“OFF”.
“OFF”.
4. Press the [DISP] button to return to the previ-
● ON:
ous mode.
Uses with connected AMP.
● OFF:
Uses with inside AMP.
Adjusting the display contrast
You can adjust the display contrast to match the
angle of installation of the unit.
∗ The factory default setting is “5”. (Adjustment level:
1 to 16)
4. Press the [ADJ] button to return to the previ-
ous mode.
Adjusting the auxiliary input
sensitivity
Adjust the auxiliary sensitivity when the audio
from an external device is difficult to hear even
after adjusting the volume.
1. Press and hold the [DISP] button for 1 second
or longer to switch to the display adjust mode.
2. Press the [a]/[d] button to select
“CONTRAST”.
3. Turn the [ROTARY] knob to adjust the con-
∗ The factory default setting is “MID”.
1. Press the [ADJ] button to switch to the adjust
trast.
4. Press the [DISP] button to return to the previ-
mode.
ous mode.
2. Press the [a]/[d] button to select
“AUX SENSE”.
Adjust Mode
3. Turn the [ROTARY] knob to select from
“LOW”, “MID” or “HIGH”.
Setting the low pass filter
4. Press the [ADJ] button to return to the previ-
∗ This function can only be adjusted when the
subwoofer output is set to “ON” and the speaker
system is set to “5.1ch”. For details on how to set
the subwoofer, refer to the subsection “Turning
on/off speakers” in the section “Changing Initial
Settings such as Menu Language, etc.”.
ous mode.
Performing a system check
This function verifies the devices hooked up
through CeNET.
∗ This function cannot be adjusted when as follows:
“Pro Logic” is set to “ON”, the speaker system is
set to “5.1ch”, DVD/DTS-CD is being played.
1. Press the [ADJ] button to switch to the adjust
mode.
2. Press the [a]/[d] button to select “SYSTM
∗ The factory default setting is “THROUGH”. If the
speaker system is set to “5.1ch”, the factory default
setting is “50Hz”.
CHK E”.
3. Press and hold the [
] button for 1 second
or longer to start the system check.
1. Press the [ADJ] button to switch to the adjust
mode.
The digital connection configuration is auto-
matically checked.
2. Press the [a]/[d] button to select
“SUB-W LPF”.
When the system check is complete, perform
the speaker setting.
3. Turn the [ROTARY] knob to select the setting.
Each time you turn the [ROTARY] knob, the
setting changes in the following order:
Turn the [ROTARY] knob to select the
speaker system and press the [
] button.
THROUGH ➜ 50Hz ➜ 80Hz ➜ 120Hz
The display returns to the previous mode.
4. Press the [ADJ] button to return to the previ-
For details on the speaker setting, refer to the
“System check and speaker setting”.
ous mode.
VXZ756
41
Common Operations
Other operations
Entering titles
Titles up to 10 characters long can be stored in
memory and displayed for CD, CD changer and
Radio/TV stations. The number of titles that can
be entered for each mode are as follows.
Clearing titles
1. Play a track or tune in to a radio/TV station for
which you want to delete the title.
2. Do one of the following:
● In the CD or CD changer mode
Press the [TITLE] button to select “USER
TITLE”.
Mode
Number of titles
50 titles
● In the radio or TV mode
CD mode
TV mode
Radio mode
Skip this step.
20 titles
3. Press and hold the [TITLE] button for 1 sec-
ond or longer to switch to the title input dis-
play.
30 titles
CD changer mode
DCZ625 connected
CDC655Tz connected
Number of titles
100 titles
4. Press and hold the [BND] button for 1 second
or longer to delete the title.
100 titles
5. Press and hold the [
] button for 2 sec-
1. Press the [SRC] button to select the mode
you want to enter a title (Radio, CD, CD
changer or TV).
onds or longer to store the setting and return
to the previous mode.
Cellular telephone mute
2. Play a track or tune in to a radio/TV station for
which you want to enter the title.
This unit requires special wiring to mute the au-
dio signal automatically when a cellular tele-
phone rings in the car.
3. Do one of the following:
● In the CD or CD changer mode
∗ This function is not compatible with all cellular tele-
phones. Contact your local authorized Clarion dealer
for information on proper installation and compat-
ibility.
Press the [TITLE] button to select “USER
TITLE”.
● In the radio or TV mode
Skip this step.
AUX function
This system has an external input jack so you
can listen to audio from an external device con-
nected to this unit.
4. Press and hold the [TITLE] button for 1 sec-
ond or longer to switch to the title input dis-
play.
5. Press the [a]/[d] button to move the cursor.
6. Press the [BND] button to select a character.
Each time you press the [BND] button, the
character changes in the following order:
Capital letters ➜ Small letters ➜ Numbers
and Symbols ➜ Umlaut ➜ Capital letters…
7. Turn the [ROTARY] knob to select the desired
character.
8. Repeat steps 5 to 7 to enter up to 10 charac-
ters for the title.
9. Press and hold the [
] button for 2 sec-
onds or longer to store the title into memory
and return to the previous mode.
42
VXZ756
9. OPERATIONS OF ACCESSORIES
CD Changer Operations
CD changer functions
Procedure to scroll a title
When an optional CD changer is connected
through the CeNET cable, this unit controls all
CD changer functions. This unit can control a
total of 2 changers.
Set “AUTO SCROL” to “ON” or “OFF”.
(The factory default setting is “ON”. Refer to the
subsection “Setting the method for title scroll”
in section “Common Operations”.)
Press the [SRC] button and select the CD
changer mode to start play. If 2 CD changers are
connected, press the [SRC] button to select the
CD changer for play.
● When set to “ON”
The title is automatically kept scrolling.
● When set to “OFF”
To scroll just 1 time when the title was changed
or you press and hold the [TITLE] button for 1
second or longer.
∗ If “NO MAG” appears in the display, insert the
magazine into the CD changer. “DISC CHECK”
appears in the display while the player loads
(checks) the magazine.
∗ If “NO DISC” appears in the display, eject the
magazine and insert discs into each slot. Then,
reinsert the magazine back into the CD
changer.
Selecting a CD
Press the [UP] or [DN] button to select the
desired disc.
∗ If a CD is not loaded in a slot of magazine,
pressing the [UP] or [DN] button can not work.
∗ Pressing the [BND] button also advances to
next disc.
Note:
• Some CDs recorded in CD-R/CD-RW mode may
not be usable.
Selecting a track
CAUTION
● Track-up
CD-ROM discs cannot be played from every
CD changer, it’s depended on the model.
1. Press the [d] button to move ahead to the
beginning of the next track.
Pausing play
2. Each time you press the [d] button, the
track advances ahead to the beginning of the
next track.
1. Press the [
] button to pause play.
“PAUSE” appears in the display.
● Track-down
2. To resume play, press the [
again.
] button
1. Press the [a] button to move back to the
beginning of the current track.
Displaying CD titles
2. Press the [a] button twice to move to the
This unit can display title data for CD-text CDs
and user titles input with this unit.
beginning of the previous track.
Fast-forward/fast-rewind
● Fast-forward
● When connected to CDC655Tz or DCZ625
Each time you press the [TITLE] button, the title
changes in the following order:
Press and hold the [d] button for 1 second or
longer.
User title (disc) ➜ CD-text title (disc) ➜ Artist
name ➜ CD-text title (track) ➜ User title
(disc)…
● Fast-rewind
Press and hold the [a] button for 1 second or
longer.
Notes:
• If the CD playing is not a CD-text CD or no user
title has been input, “NO TITLE” appears in the
display.
• If a CD-text CD is not input its disc title or a track
title, “NO TITLE” appears in the display.
VXZ756
43
CD Changer Operations
Scan play
Disc random play
Scan play locates and plays the first 10 seconds
of each track on a disc automatically. This
function continues on the disc until it is
cancelled.
The disc random play selects and plays
individual tracks or discs automatically in no
particular order. This function continues
automatically until it is cancelled.
∗ The scan play is useful when you want to
1. Press and hold the [RDM] button for 1
select a desired track.
second or longer.
1. Press the [SCN] button.
2. To cancel disc random play, press the [RDM]
2. To cancel the scan play, press the [SCN]
button again.
button again.
Disc scan play
Disc scan play locates and plays the first 10
seconds of the first track on each disc in the
currently selected CD changer. This function
continues automatically until it is cancelled.
∗ Disc scan play is useful when you want to
select a desired CD.
1. Press and hold the [SCN] button for 1 second
or longer.
2. To cancel disc scan play, press the [SCN]
button again.
Repeat play
Repeat play continuously plays the current track.
This function continues automatically until it is
cancelled.
1. Press the [RPT] button.
2. To cancel repeat play, press the [RPT] button
again.
Disc repeat play
After all the tracks on the current disc have been
played, disc repeat play automatically replays the
current disc over from the first track. This
function continues automatically until it is
cancelled.
1. Press and hold the [RPT] button for 1 second
or longer.
2. To cancel disc repeat play, press the [RPT]
button again.
Random play
Random play selects and plays individual tracks
on the disc in no particular order. This function
continues automatically until it is cancelled.
1. Press the [RDM] button.
2. To cancel random play, press the [RDM]
button again.
44
VXZ756
TV Operations
1. Press the [BND] button and select the desired
TV tuner functions
band (TV1 or TV2).
When an optional TV tuner is connected through
the CeNET cable, this unit controls all TV tuner
functions. To watch TV it requires a TV tuner and
a monitor.
∗ If “MANU” is not lit in the display, press and
hold the [BND] button for 1 second or longer.
“MANU” lights in the display and manual tuning
is now available.
2. Tune into a station.
Watching a TV
●Quick tuning:
1. Press the [SRC] button and select the TV
Press and hold the [a]/[d] button for 1 sec-
mode.
ond or longer to tune in a station.
2. Press the [BND] button to select the desired
TV band (TV1 or TV2). Each time the button
is pressed, the input selection toggles be-
tween TV1 and TV2.
●Step tuning:
Press the [a]/[d] button to manually tune in
a station.
3. Press the [a]/[d] button to tune in the de-
Recalling a preset station
sired TV station.
A total of 12 TV stations can be stored (6-TV1
and 6-TV2). This allows you to select your favor-
ite TV stations and store them in memory.
Watching a video
The TV tuner features a VTR input for an external
A/V source, such as a game station.
1. Press the [BND] button and select the desired
TV band (TV1 or TV2).
1. Press and hold the [ADJ] button for 1 second
2. To recall a stored TV station, press the de-
or longer to select VTR.
sired [DIRECT] button to select that station.
2. To return to the TV broadcast, press and hold
∗ Press and hold one of the [DIRECT] buttons for
2 seconds or longer to store the current station
into preset memory.
the [ADJ] button for 1 second or longer.
TV tuning
There are 3 types of TV tuning modes available,
seek, manual and preset tuning.
Manual memory
1. Select the desired station with seek tuning,
manual tuning or preset tuning.
Seek tuning
1. Press the [BND] button and select the desired
2. Press and hold one of [DIRECT] buttons for 2
seconds or longer to store the current station
into preset memory.
TV band (TV1 or TV2).
∗ If “MANU” is lit in the display, press and hold
the [BND] button for 1 second or longer.
“MANU” in the display goes off and seek tuning
is now available.
Auto store
Auto store selects 6 TV stations automatically
and stores each one into preset memory.
2. Press the [a]/[d] button to automatically
seek a station. Press the [d] button to auto-
matically tune up the frequency band to the
next available TV station; press the [a] but-
ton to automatically tune down.
If the 6 stations with good reception are not avail-
able, stations previously stored in memory re-
main. Only stations with strong reception are
stored into memory.
1. Press the [BND] button and select the desired
Manual tuning
TV band (TV1 or TV2).
There are 2 ways available: Quick tuning and
step tuning.
2. Press and hold the [PS/AS] button for 2 sec-
onds or longer. The stations with good recep-
tion are stored automatically to the preset
channels.
When you are in the step tuning mode, the fre-
quency changes one step at a time. In the quick
tuning mode, you can quickly tune the desired
frequency.
VXZ756
45
TV Operations
Preset scan
Setting the TV diver
Preset scan allows the user to view each preset
position before it automatically advances to the
next preset. This function is useful for searching
for a desired TV station in memory.
You can change the reception setting for the TV
antenna connected to the TV tuner.
∗ The factory default setting is “ON”.
1. Press the [ADJ] button to switch to the adjust
1. Press the [PS/AS] button.
mode.
2. When the desired station is found, press the
[PS/AS] button again to remain tuned to that
station.
2. Press the [a]/[d] button to select “TV
DIVER”.
3. Turn the [ROTARY] knob to select “ON” or
Note:
“OFF”.
• Do not press and hold the [PS/AS] button for 2
seconds or longer. Doing so will trigger the auto
store function and start storing stations into
memory.
● ON:
Sets the diver setting to ON.
● OFF:
Sets the diver setting to OFF.
Setting up the TV type
4. Press the [ADJ] button to return to the previ-
Set the TV type to NTSC, PAL, MULTI.
ous mode.
1. Press the [ADJ] button to switch to the adjust
mode.
2. Press the [a] or [d] button to select “TV
TYPE”.
3. Turn the [ROTARY] knob to select the
setting.
Each time you turn the [ROTARY] knob, the
setting changes in the following order.
MULTI ➜ NTSC ➜ PAL
4. Press the [ADJ] button to return to the
previous mode.
Setting the TV area
When you select the TV area (TV reception
area), the TV tuner area setting changes.
1. Press the [ADJ] button to switch to the adjust
mode.
2. Press the [a]/[d] button to select “TV
AREA E”.
3. Press the [
] button.
4. Turn the [ROTARY] knob to select the
reception area.
5. Press the [
] button.
6. Press the [ADJ] button to return to the
previous mode
The above operations are required when a TV
tuner other than TTX7501z is connected.
46
VXZ756
10. IN CASE OF DIFFICULTY
Problem
Cause
Measure
Power does not
turn on.
Fuse is blown.
Replace with a fuse of the same amperage. If the
fuse blows again, consult Clarion dealer.
(No sound is
produced.)
Incorrect wiring.
Consult Clarion dealer.
No audio when
operating the unit shorted to ground or
Amplifier turn-on lead is
Turn the unit off and check each wire for a possible
short. If the amplifier turn-on lead shorts out, cover it
with amplifiers.
excessive current is required. with insulation such as tape.
Nothing happens The microprocessor has
when buttons are malfunctioned due to noise,
Turn off the power, then
press the [RELEASE] button
and remove the DCP.
pressed.
etc.
Press the reset button for
about 2 seconds with a thin
rod.
Reset button
Display is not
accurate.
DCP or source unit
connectors are dirty.
Wipe the dirt off with a soft cloth moistened with
cleaning alcohol.
No audio.
The speaker protection
circuit is operating.
1. Check the speaker connection.
2. Turn down sound volume. Function can also be
restored by turning the power off and on again.
3. If the sound is muted again, consult Clarion dealer.
No audio.
MP3/WMA files are absent
on the disc.
Write MP3/WMA files onto the disc properly.
Files are not recognized as
an MP3/WMA file.
Use MP3/WMA files encoded properly.
File system is not correct.
Use ISO9660 level 1, 2 or JOLIET or Romeo file system.
Clean the disc with a soft cloth.
Sound skips or is Disc is dirty.
noisy.
Disc is heavily scratched or
Replace with a disc with no scratches.
warped.
Sound is cut or
skipped.
MP3/WMA files are not
encoded properly.
Use MP3/WMA files encoded properly.
Noise is generated
or noise is mixed
with sound.
Poor sound quality Water droplets may form on Let dry for about 1 hour with the power on.
in extremely cold
weather or
the internal lens when the
car is parked in a humid
extreme humidity. place.
Wrong filename
File system is not correct.
Use ISO9660 level 1, 2 or JOLIET or Romeo file system.
Play list play is
not performed.
File name or extension is not Use ASCII characters for MP3/WMA file name.
correct.
Use “.M3U” for the file extension of a play list.
VXZ756
47
11. ERROR DISPLAYS
If an error occurs, one of the following displays is displayed.
Take the measures described below to eliminate the problem.
Error Display
ERROR 2
Cause
Measure
A DISC is caught inside the DVD deck and
is not ejected.
This is a failure of DVD deck’s mechanism
and consult Clarion dealer.
ERROR 3
ERROR 6
A DISC cannot be played due to scratches,
etc.
Replace with a non-scratched disc.
Eject the disc then reload it properly.
Set the correct Parental level.
A DISC is loaded upside-down inside the
DVD deck and cannot play.
ERROR P
ERROR R
Parental level error
Region code error
Eject the disc and replace correct region
code disc.
ERROR 2
ERROR 3
ERROR 6
A DISC inside the CD changer is not loaded This is a failure of CD changer’s mechanism
properly.
and consult Clarion dealer.
A DISC inside the CD changer cannot be
played due to scratches, etc.
Replace with a non-scratched disc.
A DISC inside the CD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
If an error display other than the ones described above appears, press the reset button. If the problem
persists, turn off the power and consult Clarion dealer.
48
VXZ756
12. SPECIFICATIONS
FM Tuner
Frequency Range:
Audio
Maximum Power Output:
87.0 MHz to 108.0 MHz
208 W (52 W × 4 ch)
Usable Sensitivity:
9 dBf
Continuous Average Power Output:
17 W × 4, into 4 Ω, 20 Hz to 20 kHz, 1%THD
50dB Quieting Sensitivity:
15 dBf
Bass Control Action (60 Hz/100 Hz/200 Hz):
+16 dB, -12dB
Alternate Channel Selectivity:
70 dB
Treble Control Action (10 kHz/15 kHz):
12 dB
Stereo Separation (1 kHz):
35 dB
Line Output Level (CD 1 kHz):
2.0 V
Frequency Response ( 3 dB):
30 Hz to 15 kHz
General
Power Supply Voltage:
AM Tuner
Frequency Range:
14.4 V DC (10.8 to 15.6 V allowable), negative
ground
531 kHz to 1629 kHz
Current Consumption:
Less than 15 A, 3A
Usable Sensitivity:
25 µV
Speaker Impedance:
4 Ω (4 Ω to 8 Ω allowable)
DVD Player section
System:
Weight / Source unit:
4 lb. (1.6 kg)
Digital Versatile Disc System with CDDA
capable
Weight / Remote control unit:
3.5 oz. (100 g) (including battery)
Usable Discs:
DVD Video Disc, Video CD, Compact disc
Dimensions / Source unit:
7” (Width) × 2” (Height) × 6-5/16” (Depth)
[178 (W) × 50 (H) × 156.5 (D) mm]
Dimensions / Remote control unit:
2-1/8” (Width) × 6-1/8” (Height) × 1-1/16” (Depth)
[54 (W) × 155 (H) × 27 (D) mm]
Frequency Response:
20 Hz to 22 kHz ( 1 dB)
Signal to Noise Ratio:
100 dB
Distortion:
0.02%
Channel Separation:
80 dB
Analog audio output:
2.0 Vrms
Note:
• Specifications and design are subject to change without notice for further improvement.
VXZ756
49
50
VXZ756
Clarion Co., Ltd.
PE-2751K
280-8177-00
2005/3
All Rights Reserved. Copyright © 2005: Clarion Co., Ltd.
|