Cateye CYCLOCOMPUTER CC COM10W User Manual

CATEYE COMMUTER  
CYCLOCOMPUTER CC-COM10W  
U.S. Pat. Nos. 5236759/5308419/6957926 Pat./Design Pat. Pending  
ENG  
CCCOM1W-100224 066600950  
2
Be sure to tighten the dial of the FlexTight bracket by hand. Tightening it strongly using  
a tool, etc. may damage the screw thread.  
When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.  
A temperature sensor is built in the computer. If the sensor is heated by direct sunlight  
or body heat, it may not indicate the temperature correctly.  
Dispose of used batteries according to local regulations.  
LCD screen may be distorted when viewed through polarized sunglass lenses.  
Wireless Sensor  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-  
tions:(1)This device may not cause harmful interference, and (2) this device must accept any inter-  
ference received, including interference that may cause undesired operation.  
Modifications  
The FCC requires the user to be notified that any changes or modifications made to this device that are  
not expressly approved by CatEye Co., Ltd. May void the user ’s authority to operate the equipment.  
WARNING / CAUTION  
Do not concentrate on the computer while riding. Ride safely!  
Install the magnet, sensor, and bracket securely. Check these periodically.  
If a child swallows a battery, consult a doctor immediately.  
Do not leave the computer in direct sunlight for a long period of time.  
Do not disassemble the computer.  
Do not drop the computer to avoid malfunction or damage.  
When you attempt to press MODE with the computer installed to the bracket, press  
around the marking section on the surface of the computer. Pressing other sections  
strongly may result in malfunction or damage.  
The sensor was designed to receive signals within a maximum range of 70 cm, to reduce  
chance of interference. When adjusting the wireless sensor, note the following:  
Signals cannot be received if the distance between the sensor and the computer is too large.  
The receiving distance may be shortened due to low temperature and exhausted batteries.  
Signals can be received only when the back of the computer is facing the sensor.  
Interference may occur, resulting in incorrect data, if the computer is:  
Near a TV, PC, radio, motor, or in a car or train.  
Close to a railroad crossing, railway tracks, TV stations and/or radar base.  
Using with other wireless devices in close proximity.  
Before using the computer, please thoroughly read this manual and keep  
it for future reference.  
How to install the unit on your bicycle  
Preparing the computer  
Operation of buttons  
when the computer is  
mounted on the bracket  
Tire circumference  
reference table  
1Bracket band  
2Bracket  
2
4
LIGHT  
5
( )  
mm  
ETRTO Tire size  
47-203 12x1.75  
54-203 12x1.95  
40-254 14x1.50  
47-254 14x1.75  
40-305 16x1.50  
47-305 16x1.75  
54-305 16x2.00  
L
1
3Nut  
Battery case cover  
935  
940  
1020  
1055  
1185  
1195  
1245  
3
4Sensor  
5Magnet  
7
MENU  
AC  
Click  
6Sensor rubber pad  
7Bracket rubber pad  
8Nylon ties (x2)  
MODE  
6
8
28-349 16x1-1/8 1290  
37-349 16x1-3/8 1300  
17x1-1/4  
km/h mph: Speed unit  
: Sensor signal reception icon  
32-369  
1340  
(
)
369  
Install the sensor and magnet  
40-355 18x1.50  
47-355 18x1.75  
32-406 20x1.25  
35-406 20x1.35  
40-406 20x1.50  
47-406 20x1.75  
50-406 20x1.95  
1340  
1350  
1450  
1460  
1490  
1515  
1565  
When using the computer for the first time or resetting to the fac-  
tory default setting, format according to the following procedure.  
The distance between the computer  
and the sensor must not exceed the  
transmission range of 70 cm. The back  
of the computer must face the sensor.  
A
B
Sensor zone  
The magnet  
passes  
through the  
sensor zone.  
Format (initialize)  
1
MENU  
1. Press and hold the MENU button.  
28-451 20x1-1/8 1545  
37-451 20x1-3/8 1615  
37-501 22x1-3/8 1770  
40-501 22x1-1/2 1785  
2. Press the AC button.  
YES!  
NO!  
3. Release the AC button.  
Right front fork  
(inside)  
AC  
47-507 24x1.75  
50-507 24x2.00  
1890  
1925  
(Keep pressing the MENU button.)  
5
4
4. Release the MENU button.  
54-507 24x2.125 1965  
(
)
25-520 24x1 520 1753  
24x3/4  
Tubuler  
Select the speed and temperature unit  
C
1785  
2
4
When MODE is pressed and held, “Speed unit”  
and “Temperature unit” will appear for selection.  
Select “km/h” or “mph” for the speed unit, and  
°C” or “°F” for the temperature unit.  
28-540 24x1-1/8 1795  
32-540 24x1-1/4 1905  
The clearance  
between the  
SENSOR ZONE  
(
)
25-559 26x1 559 1913  
5
32-559 26x1.25  
37-559 26x1.40  
40-559 26x1.50  
47-559 26x1.75  
50-559 26x1.95  
54-559 26x2.10  
1950  
2005  
2010  
2023  
2050  
2068  
sensor and  
magnet is 5  
mm or less.  
Max  
70 cm  
Unit  
selection  
Switch the screen  
(press & hold)  
Register  
the setting  
57-559 26x2.125 2070  
MENU  
* The magnet may be installed anywhere on the spoke  
if the above installation conditions are satisfied.  
MODE  
58-559 26x2.35  
75-559 26x3.00  
2083  
2170  
MODE  
28-590 26x1-1/8 1970  
37-590 26x1-3/8 2068  
37-584 26x1-1/2 2100  
1
2
Right front fork  
Install the sensor  
Install the magnet  
Set the date  
650C Tubuler  
1920  
3
Spoke on the right  
26x7/8  
4
When MODE is pressed and held, “Date format”,  
“Day”, “Month”, and “Year” will appear, in this  
order. Press MODE to change the value, and press  
MENU to register it. Set the values in the subsequent  
settings with in the same procedure.  
20-571 650x20C 1938  
23-571 650x23C 1944  
650x25C  
8
Pull  
securely  
5
SENSOR ZONE  
25-571  
1952  
(
)
26x1 571  
6
40-590 650x38A  
40-584 650x38B  
(
2125  
2105  
)
25-630 27x1 630 2145  
28-630 27x1-1/8 2155  
32-630 27x1-1/4 2161  
37-630 27x1-3/8 2169  
18-622 700x18C 2070  
19-622 700x19C 2080  
20-622 700x20C 2086  
23-622 700x23C 2096  
25-622 700x25C 2105  
28-622 700x28C 2136  
30-622 700x30C 2146  
32-622 700x32C 2155  
To the sensor zone  
* Install the sensor to the front fork as high as possible.  
Switch D/M and  
M/D or increase  
the value  
Switch the screen  
(press & hold)  
Register  
the setting  
3
Attach the bracket to the stem or handlebar  
MENU  
MODE  
MODE  
When attaching the bracket to the stem  
7
Stem  
Set the clock  
When MODE is pressed and held, “Display format”,  
“Hour”, and “Minute” will appear, in this order.  
* When 12h is selected, “AM/PM selection” is required.  
4
Cut  
2
1
Caution:  
700C  
Tubuler  
2130  
Round off the cut edge  
of the bracket band to  
prevent injury.  
12h  
24h  
Switch the  
screen  
Register  
the setting  
35-622 700x35C 2168  
38-622 700x38C 2180  
40-622 700x40C 2200  
42-622 700x42C 2224  
44-622 700x44C 2235  
45-622 700x45C 2242  
47-622 700x47C 2268  
(AM  
PM) or  
MENU  
increase the value  
(press & hold)  
MODE  
MODE  
When attaching the bracket to the handlebar  
* On account of the receiving sensitivity, attach the  
bracket so that the computer is kept horizontal.  
Enter the tire circumference  
Enter the tire circumference of your bicycle in mm.  
* Refer to the tire circumference reference table.  
Handlebar  
5
6
54-622 29x2.1  
60-622 29x2.3  
2288  
2326  
7
Measure more ac-  
curate tire circumfer-  
ence (L) of your bike  
To get the most  
accurate calibration  
do a wheel roll out.  
With the valve stem  
perpendicular to the  
ground, mark the  
pavement at the valve  
stem. With the riders  
weight on the bike,  
roll the wheel one tire  
revolution in a straight  
line and mark the  
ground when the valve  
stem is perpendicular  
to the ground again.  
Measure the distance in  
millimeters. This is the  
most accurate wheel  
calibration number.  
3
Increase  
the value  
Move digits  
Register the  
setting  
2
1
(press & hold)  
MENU  
MODE  
MODE  
To carry over the total distance  
After you performed the formatting operation, or  
purchased a new computer, you can start the total  
distance with the value you enter. The total distance  
is entered as a 5-digit integer number in km [mile].  
* To start the total distance with 0, press MENU without  
entering any value, and complete the setting.  
4
* For wing type handlebar or oversized stem,  
bracket can be mounted using the Bracket  
Holder and nylon ties. (Option)  
Remove/install the computer  
While supporting it by hand,  
Click  
2
Register the setting  
(Finish)  
Move digits  
(press & hold)  
Increase  
the value  
MENU  
push it out as if lifting  
the front up  
MODE  
MODE  
* After installation, check that the speed is displayed on the computer when gently turning the  
front wheel. When it is not displayed, check the positions of and  
A
,
B
C
.
1
L mm  
How to restart  
Specification  
Battery  
Computer : Lithium battery (CR2032) x 1, Sensor : Lithium battery (CR2032) x 1  
After changing the battery, or when the computer displays an error, restart the computer  
Battery life Computer : Approx. 1 years (If the computer is used for 1 hour/day; the battery life will vary  
depending on the conditions of use.)  
according to the following procedure.  
* With the restarting operation, the speed unit, date, tire size, and record data in the data view are retained.  
* When the restarting operation is performed before 0:00 in the morning, the trip distance and the Car-  
bon offset for the day are not saved due to the data view’s update timing. To retain the measurement  
data for the day, perform the restarting operation before starting measurement on the next day.  
Refer to “Data view’s update timing” for the procedure to save the data view.  
Sensor : Unit Total Distance reaches about 10000 km (6250 mile)  
*
*
It may be shortened significantly when backlight is used frequently.  
This is the average figure of being used under 20 °C temperature and the distance between the  
computer and the sensor is 65 cm.  
Controller..........................4 bit, 1-chip microcomputer (Crystal controlled oscillator)  
Display..............................Liquid crystal display  
Sensor ..............................No contact magnetic sensor  
Transmission distance......Between 20 and 70 cm  
Tire circumference range ......0100 mm - 3999 mm (Initial value: 2096 mm)  
Working temperature........32 °F - 104 °F (0 °C - 40 °C) (This product will not display appropriately when  
exceeding the Working Temperature range. Slow response or black LCD at lower or  
higher temperature may happen respectively.)  
Dimensions/weight Computer : 2-9/32” x 1-1/2” x 3/4” (58 x 38 x 19 mm) / 1.02 oz (29 g)  
Sensor : 1-41/64” x 1-3/8” x 19/32” (41.5 x 35 x 15 mm) / 0.53 oz (15 g)  
The factory-loaded battery life might be shorter than the above-mentioned specification.  
The specifications and design are subject to change without notice.  
1. Press the AC button on the back of the computer.  
2. Set the date. To set the date, refer to “Preparing the computer-3”.  
* At the time of setting the date, the latest record date in the data view is initially displayed, and any  
date before that cannot be set.  
3. Set the clock. Refer to “Preparing the computer 4”.  
Maintenance  
*
*
To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and  
wipe it off with a dry cloth.  
Standard parts  
Optional parts  
#160-2196  
Speed sensor  
#160-2193  
Bracket  
#169-9691  
Wheel  
magnet  
COIN  
Replacing the battery  
Computer  
If turns on, replace the battery. Install a new lithium battery  
(CR2032) with the (+) side facing upward. After the battery change,  
go through the restart operation, by pressing the AC button.  
* Then restart the computer according to “How to restart”.  
#160-2190  
Parts kit  
#160-2770  
Bracket holder  
Close  
#160-0280  
Bracket band  
Open  
CR2032  
#166-5150  
Lithium battery (CR2032)  
Sensor  
When the speed is not displayed even after adjusting cor-  
rectly, replace the battery. Install a new lithium battery  
(CR2032) with the (+) side facing upward. After replacement,  
check the positions of the sensor and magnet.  
CR2032  
Close  
Open  
COIN  
Troubleshooting  
MODE does not work when the computer is mounted on its bracket.  
Check that there is no dirt between the bracket and the computer.  
Wash off the bracket with water to get rid of any dirt.  
The sensor signal reception icon does not flash (the speed is not displayed). (Move the com-  
puter near the sensor, and turn the front wheel. If the sensor signal reception icon flashes, this  
trouble may be a matter of transmission distance due to battery drain, but not any malfunction.)  
Check that the clearance between the sensor and magnet is not too large. (Clearance: within 5 mm)  
Check that the magnet passes through the sensor zone correctly.  
Adjust the positions of the magnet and sensor.  
Is the computer installed at the correct angle?  
Back of computer must face toward the sensor.  
Check that the distance between the computer and sensor is correct. (Distance: within 20 to 70 cm)  
Install the sensor within the specified range.  
Is the computer or sensor battery weak?  
In winter, battery performance diminishes.  
Replace with new batteries. After replacement, follow the procedure “Replacing the battery”.  
No display.  
Is battery in the computer run down?  
Replace it. Then restart the computer referring to “How to restart”.  
Incorrect data appear.  
Restart the computer referring to “How to restart”.  
3

Advent ADV10 User Manual
Blaupunkt RDM 169 US User Manual
Citizen Calculator SRP 280N User Manual
Clarion OHM641 User Manual
Dell Car Video System 2407WFP HC User Manual
DXG Technology DXG DXG 565V User Manual
Geneva Lab SOUNDS SYSTEM XL User Manual
Grundig 400 PE User Manual
JVC 1000MKV_UN_VP User Manual
JVC GR DV3000A User Manual