PUB.DIM-536
Digital Video Camcorder
English
Instruction Manual
Camescope vidéo numérique
Françai
s
Manuel d’instruction
Videocámara digital
Español
Manual de Instrucciones
Digital
Video
Cassette
Mini
This instruction manual covers the OPTURA20 and OPTURA10. Please note that
illustrations and explanation in this manual are based on the OPTURA20.
Ce manuel d’instruction traite des modèles OPTURA20 et OPTURA10. Veuillez noter
que les illustrations et les explications contenues dans ce manuel sont basées sur le
OPTURA20.
Este manual de instrucciones cubre la OPTURA20, y la OPTURA10. Tenga en cuenta
que las ilustraciones y las explicaciones de este manual se basan en la OPTURA20.
NTSC
Important Usage Instructions
WARNING:
E
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
COPYRIGHT WARNING:
Unauthorized recording of copyrighted materials may infringe on the rights of
copyright owners and be contrary to copyright laws.
Digital Video Camcorder, OPTURA20/OPTURA10 systems
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and use in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual.
If such changes or modifications should be made, you could be required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516)328-5600
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
Important Warning
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
the product’s enclosure, that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
The exclamation point, within an
equilateral triangle, is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the product.
SERVICE PERSONNEL.
2
IMPORTANT SAFETY INSTRUCTIONS
In these safety instructions the word “product”
refers to the Canon Digital Video Camcorder
OPTURA20/OPTURA10 and all its accessories.
10. Power Sources — The CA-570 Compact
Power Adapter should be operated only
from the type of power source indicated on
the marking label. If you are not sure of the
type of power supply to your home, consult
your product dealer or local power
E
1. Read Instructions — All the safety and
operating instructions should be read
before the product is operated.
company. Regarding other power sources
such as battery power, refer to instructions
in this manual.
2. Retain Instructions — The safety and
operating instructions should be retained
for future reference.
11. Polarization — The CA-570 Compact Power
Adapter is equipped with a polarized 2-
prong plug (a plug having one blade wider
than the other).
3. Heed Warnings — All warnings on the
product and in the operating instructions
should be adhered to.
The 2-prong polarized plug will fit into the
power outlet only one way. This is a safety
feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug.
If the plug still fails to fit, contact your
electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the
polarized plug.
4. Follow Instructions — All operating and
maintenance instructions should be
followed.
5. Cleaning — Unplug this product from the
wall outlet before cleaning. Do not use
liquid or aerosol cleaners. The product
should be cleaned only as recommended in
this manual.
12. Power Cord Protection — Power cords
should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them. Pay particular
attention to plugs and the point from
which the cords exit the product.
6. Accessories — Do not use accessories not
recommended in this manual as they may
be hazardous.
7. Avoid magnetic or electric fields — Do not
use the camera close to TV transmitters,
portable communication devices or other
sources of electric or magnetic radiation.
They may cause picture interference, or
permanently damage the camera.
13. Outdoor Antenna Grounding — If an
outside antenna is connected to the
product, be sure the antenna is grounded
so as to provide some protection against
voltage surges and built-up static charges.
Section 810 of the National Electrical Code,
ANSI / NFPA No. 70—1984, provides
information with respect to proper
8. Water and Moisture — Hazard of electric
shock — Do not use this product near
water or in rainy/moist situations.
grounding of the mast and supporting
structure, grounding of the lead-in wire to
an antenna discharge unit, size of
grounding conductors, location of antenna
discharge unit, connection to grounding
electrodes, and requirements for the
grounding electrode. See figure 1.
9. Placing or Moving — Do not place on an
unstable cart, stand, tripod, bracket or
table. The product may fall, causing serious
injury to a child or adult, and serious
damage to the product.
A product and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the product and cart combination to
overturn.
3
18. Damage Requiring Service — Disconnect
this product from the wall outlet and all
power sources including battery, and refer
servicing to qualified service personnel
under the following conditions:
EXAMPLE OF ANTENNA GROUNDING AS
PER NATIONAL ELECTRICAL CODE
Fig. 1
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
E
a. When the power-supply cord or plug is
damaged.
ANTENNA
DISCHARGE
UNIT
(NEC SECTION
810-20)
b. If any liquid has been spilled onto, or
objects have fallen into, the product.
c. If the product has been exposed to rain
or water.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE
GROUNDING ELECTRODE
SYSTEM
(NEC ART 250. PART H)
NEC - NATIONAL ELECTRICAL CODE
d. If the product does not operate normally
even if you follow the operating
instructions. Adjust only those controls
that are covered by the operation
instructions. Improper adjustment of
other controls may result in damage and
will often require extensive work by a
qualified technician to restore the
product to its normal operation.
e. If the product has been dropped or the
cabinet has been damaged.
14. Lightning — For added protection of this
product during a lightning storm, or when
it is left unattended and unused for long
periods of time, disconnect it from the wall
outlet and disconnect the antenna. This will
prevent damage to the product due to
lightning and power-line surges.
15. Overloading — Do not overload wall outlets
and extension cords as this can result in a
risk of fire or electric shock.
f. When the product exhibits a distinct
change in performance. This indicates a
need for service.
16. Objects and Liquid Entry — Never push
objects of any kind into this product
through openings as they may touch
dangerous voltage points or short out parts
that could result in a fire or electric shock.
Be careful not to spill liquid of any kind
onto the product.
19. Replacement Parts — When replacement
parts are required, be sure the service
technician has used replacement parts that
are specified by Canon or that have the
same characteristics as the original part.
Unauthorized substitutions may result in
fire, electric shock or other hazards.
17. Servicing — Do not attempt to service this
product yourself as opening or removing
covers may expose you to dangerous
voltage or other hazards. Refer all servicing
to qualified service personnel.
20. Safety Check — Upon completion of any
service or repairs to this product, ask the
service technician to perform safety checks
to determine that the product is in safe
operating order.
When replacement of power supply is required, please return it to the
responsible nearest Canon Service Center and please replace it with the same
type number CA-570.
The Adapter can be used with a power supply between 100 and 240 V AC.
For areas where 120 V AC power is not used, you will need a special plug
adapter. Contact your nearest Canon Service Center for further information.
4
Reference Guide
The following manuals are supplied with the camcorder:
E
❍ Digital Video Camcorder OPTURA20/OPTURA10 Instruction Manual
This manual explains the camcorder operations from basic video recording to the
use of the full range of features.
❍ DIGITAL VIDEO SOLUTION DISK Software Instruction Manual
This manual explains how to download images from the memory card to a
computer using the supplied USB cable. You can add sample images for Card Mix
and My Camera settings from the supplied DIGITAL VIDEO SOLUTION DISK.
❍ Windows XP Users Only
DV NETWORK SOLUTION DISK Software Instruction Manual
This manual explains how to download/upload images from/to the memory card
using a DV (IEEE1394) cable. You can also perform videoconference and file transfer
over the Internet using the provided software. Available functions depend upon
the camcorder model of your contact and networking environment.
Trademark Acknowledgements
• Canon and Bubble Jet are registered trademarks of Canon Inc.
• D is a trademark.
•
logo is a trademark.
• Windows® is either a registered trademark or trademark of Microsoft Corporation in
the United States and/or other countries.
• Other names and products not mentioned above may be registered trademarks or
trademarks of their respective companies.
5
Table of Contents
Introduction
E
Reference Guide..............................................................................................................5
Thank You for Choosing a Canon ................................................................................9
Introducing the OPTURA20/OPTURA10 ....................................................................10
Components Guide ......................................................................................................11
Mastering the Basics
Preparations
Using a Household Power Source ..............................................................................15
Attaching and Charging the Battery Pack ................................................................16
Installing the Backup Battery ......................................................................................19
Preparing the Camcorder ............................................................................................20
Loading a Cassette........................................................................................................22
Using the Wireless Controller......................................................................................24
Setting the Time Zone, Date and Time......................................................................25
Basic Recording
Recording Movies on a Tape ......................................................................................28
Zooming ........................................................................................................................30
Using the LCD Screen....................................................................................................32
Searching and Reviewing when Recording ..............................................................35
Tips for Making Better Videos ....................................................................................36
Basic Playback
Playing Back a Tape ......................................................................................................37
Playing Back on a TV Screen........................................................................................40
Using the Full Range of Features
General
Menus and Settings ......................................................................................................43
Changing the Remote Sensor Mode..........................................................................48
Customizing the Camcorder........................................................................................49
Other Camcorder Settings ..........................................................................................50
Recording
Changing the Recording Mode (SP/LP)......................................................................52
Recording Still Images on the Tape............................................................................53
Using the Recording Programs....................................................................................55
Using Digital Effects......................................................................................................59
Using the Multi-Image Screen ....................................................................................65
Turning Off the Image Stabilizer ................................................................................67
Recording With the Self-Timer....................................................................................68
Audio Recording ..........................................................................................................69
Using the VL-3 Video Light (Optional) ......................................................................71
Using the VFL-1 Video Flash Light (Optional) ..........................................................72
Using the DM-50 Microphone (Optional)..................................................................75
6
Manual Adjustments
Adjusting the Focus Manually ....................................................................................76
Adjusting Exposure Manually......................................................................................78
Setting the Shutter Speed............................................................................................79
Setting the White Balance ..........................................................................................81
E
Playback
Magnifying the Image..................................................................................................83
Displaying the Data Code ............................................................................................84
Photo Search/Date Search............................................................................................86
Returning to a Pre-marked Position ..........................................................................87
Editing
Recording to a VCR or Digital Video Device ............................................................88
Recording from Analog Video Devices (VCR, TV or Camcorder) ..........................90
Recording from Digital Video Devices (DV Dubbing)..............................................91
Converting Analog Signals into Digital Signals (Analog-Digital Converter) ........93
Replacing Existing Scenes (AV Insert) ........................................................................95
Audio Dubbing..............................................................................................................97
Connecting to a Computer Using a DV (IEEE1394) Cable ....................................100
Using a Memory Card
Inserting and Removing the Memory Card ............................................................101
Selecting the Image Quality/Size ..............................................................................102
Recording Still Images on a Memory Card..............................................................105
Recording Panoramic Images (Stitch Assist Mode) ................................................111
Recording Motion JPEG Movies on a Memory Card..............................................113
Playing Back a Memory Card ....................................................................................115
Protecting Images ......................................................................................................118
Erasing Images ............................................................................................................119
Selecting Still Images for Printing (Print Order) ....................................................120
Printing with the Direct Print Function....................................................................122
Combining Images (Card Mix) ..................................................................................128
Copying Still Images....................................................................................................132
Formatting a Memory Card ......................................................................................134
Connecting to a Computer Using a USB Cable ......................................................135
Creating a Start-up Image ........................................................................................136
Memory Card Information ........................................................................................137
Additional Information
Screen Displays ............................................................................................................140
List of Messages ..........................................................................................................144
Maintenance................................................................................................................147
Troubleshooting ..........................................................................................................150
System Diagram ..........................................................................................................153
Optional Accessories ..................................................................................................154
Specifications ..............................................................................................................157
Index ............................................................................................................................159
7
Conventions Used in This Manual
Operating Modes
E
Position of the
POWER Switch
Position of the
TAPE/CARD Switch
Operating Mode
CAMERA
PLAY (VCR)
CAMERA
b (TAPE)
b (TAPE)
(CARD)
PLAY (VCR)
CAMERA
CARD CAMERA
CARD PLAY (VCR)
PLAY (VCR)
(CARD)
Available functions depend upon the operating mode. It is indicated as follows:
CAMERA
: Function can be used in this mode.
CAMERA
: Function cannot be used in this mode.
Other Symbols and References
❍
❍
❍
❍
❍
: Reference page number.
: Functions to be operated on the body of the camcorder.
: Functions to be operated on the wireless controller.
: Additional topics that complement the basic operating procedures.
: Precautions related to the camcorder operation.
❍ Capital letters are used to refer to buttons on the camcorder or the wireless
controller.
❍ [ ] are used to refer to menu items displayed on the screen.
❍ “Screen” refers to the LCD and the viewfinder screen.
The serial number of this product can be found at the battery attachment unit of
the camcorder. Write down the number and other information here and retain this
book as a permanent record of your purchase to aid identification in case of theft.
Date of Purchase:
Purchased From:
Dealer Address:
Dealer Phone No.:
Model Name: OPTURA20/OPTURA10
Serial No.:
8
Thank You for Choosing a Canon
The Canon OPTURA20/OPTURA10 provides a full range of options and functions. We
recommend reading this manual thoroughly before you use the camcorder. It will help
you to become more familiar with your camcorder, and learn how to operate it
properly.
E
We suggest that you master the basic operations of the camcorder first, before
moving on to its full range of features.
Checking Supplied Accessories
WL-D79 Wireless
Controller
Two AA Batteries
Lens Cap and Lens
Cap Cord
SS-800 Shoulder Strap
Lithium Button
Battery CR2025
CA-570 Compact
Power Adapter
(incl. power cord)
STV-250N Stereo
Video Cable
BP-512 Battery Pack,
BP-508 Battery Pack
IFC-300PCU USB Cable SDC-8M SD Memory
Card (containing
Case for SD Memory
Card
DIGITAL VIDEO
SOLUTION DISK
sample images)
DV NETWORK
SOLUTION DISK
9
Introducing the OPTURA20/OPTURA10
Megapixel CCD
Advanced Accessory Shoe
E
Simply slide Canon’s VFL-1 Video Flash
Light, DM-50 Directional Stereo
Microphone or VL-3 Video Light into the
accessory shoe; the camcorder provides
power and connections.
The OPTURA20 and OPTURA10
incorporate a megapixel CCD, allowing
recording of high-resolution still images
on a memory card.
16× Optical and
320× Digital Zoom
(Card: 15× Optical and 60× Digital Zoom)
Digital Effects
Show your creativity by using the special
effects and faders. The multi-image
screen captures moving subjects in 4, 9 or
16 sequences of still images.
Image Stabilizer
Stabilizes your recordings even in long
telephoto shots.
Memory Card
You can record images on a SD Memory
Card or MultiMediaCard. Images
recorded in Stitch Assist mode can be
merged into one panoramic scene with
the supplied software.
Night Mode
Allows recording even in dark places.
The Night mode adjusts automatically to
the optimum shutter speed.
Super Night Mode and
Low Light Plus Mode (OPTURA20)
Direct Print
You can print still images by connecting
to a Canon printer with Direct Print
function.
With the OPTURA20’s Super Night mode
(in CAMERA mode) and Low Light Plus
mode (in CARD CAMERA mode), you can
keep on shooting without turning the
lights on. The assist lamp (White LED)
lights up to illuminate the subject.
USB Terminal
Allows transfer of memory card data to a
computer with built-in USB port. You can
organize and edit images on your
computer using the supplied software.
Still Images
Just press the photo button to capture
still images like photographs.
IEEE1394 DV Terminal
The DV terminal allows high-quality
transfer with virtually no deterioration in
quality of images. You can edit images
by connecting the camcorder to a PC
with IEEE1394 terminal. Windows XP
users can use the supplied software to
perform videoconference and file
transfer over the Internet*.
My Camera Settings
You can personalize your camcorder by
customizing the start-up image and
camcorder sounds.
Analog Line-in Recording/
Audio Dubbing/AV Insert Editing
*
Windows Messenger 4.5 or higher required.
10
Components Guide
OPTURA20/OPTURA10
E
REC SEARCH
–
button (p. 35) /
(record review) button (p. 35) /
(rewind) button (p. 37) /
CARD
–
button (p. 115)
REC SEARCH + button (p. 35) /
(fast forward) button (p. 37) /
CARD + button (p. 115)
CARD MIX button (p. 128) /
SLIDE SHOW button (p. 116)/
(stitch assist) button (p. 111)
(stop) button (p. 37) /
INDEX SCREEN button (p. 116)
(play/pause) button (p. 37)
DIGITAL EFFECTS
button (p. 59)
REC PAUSE (LINE-IN) button (p. 90,91) /
(self-timer) button (p. 68)
Digital effects
ON/OFF button
(p. 59)
TAPE/CARD switch (p. 8)
Using a tape
b
Using a memory card
EXP button (p. 78)
LCD screen
3.5 inch
2.5 inch
(p. 32)
FOCUS (∞) button
(p. 76)/
DATA CODE button
(p. 84)
BATT. (battery release)
button (p. 16)
Backup battery
compartment (p. 19)
Battery attachment unit
(p. 16) / Serial number
Memory card slot
(p. 101)
LCD panel
OPEN button (p. 32)
Strap mount (p. 21)
POWER indicator
Card access indicator
(p. 105)
Program selector (p. 55)
Easy recording
MENU button (p. 43)
Program AE
Q
Selector dial (p. 39, 43)
11
E
Diopter adjustment
lever (p. 20)
Zoom lever (p. 30)
Advanced accessory shoe (p. 71)
Accessory Shoe Cover (p. 21)
Focus ring
(p. 76)
Viewfinder (p. 20)
PHOTO button
(p. 53, 105)
Built-in speaker
(p. 39)
Start/stop button (p. 28)
POWER switch (p. 8)
Grip belt (p. 20)
Strap mount (p. 21)
CAMERA
OFF
Cassette compartment
]
(p. 22)
PLAY(VCR)
Cassette compartment
cover (p. 22)
12
E
Remote sensor
(p. 24)
Assist lamp
(White LED)
(p. 57)
Terminal cover
Stereo microphone
(p. 69)
S-video IN/OUT terminal (p. 40)
USB terminal
(p. 122, 135)
DV IN/OUT terminal
(p. 89)
Bottom view
MIC terminal (p. 69)
CHARGE indicator
(p. 16)
DC IN terminal (p. 15)
Tripod socket (p. 36)
AV IN/OUT terminal
(p. 40) / (phones)
terminal (p. 39, 70)
OPEN/EJECT switch (p. 22)
13
WL-D79 Wireless Controller
E
q
w
!
!
!
!
!
e
START
ZOOM
W
T
PHOTO
/STOP
r
SELF T. D.EFFECT.
MENU
SET
t
!
#
ON/OFF
TV SCREEN
#
INDEX SLIDE SHOW
CARD
@
@
#
y
u
DATA CODE
SEARCH SELECT
REW
ZERO SET
MEMORY
PLAY
STOP
SLOW
FF
@
@
12bit
AUDIO OUT
AUDIO DUB. PAUSE
2
i
o
@
@
AV INSERT AV DV REMOTE SET
REC
PAUSE
-
WIRELESS CONTROLLER WL D79
@
@
@
@
#
!
!
!
!
PHOTO button (p. 53, 105)
MENU button (p. 43)
SET button (p. 43)
!
!
@
@
@
@
@
@
@
@
@
@
#
#
#
#
q
w
e
r
t
y
u
i
o
!
!
!
!
!
!
!
!
D. EFFECTS (Digital effects) button (p. 59)
START/STOP button (p. 28)
SELF T. button (p. 68)
Search buttons (p. 86)
PLAY button (p. 37)
TV SCREEN button (p. 140)
DATA CODE button (p. 84)
FF
button (p. 37)
button (p. 38)
SEARCH SELECT button (p. 86)
ZERO SET MEMORY button (p. 87)
12bit AUDIO OUT button (p. 99)
AUDIO DUB. button (p. 98)
STOP button (p. 37)
2 button (p. 38)
REMOTE SET button (p. 48)
SLOW button (p. 38)
AV DV button (p. 94)
button (p. 38)
REC PAUSE button (p. 90)
REW
button (p. 37)
AV INSERT button (p. 96)
Digital effects ON/OFF button (p. 59)
Transmitter
PAUSE button (p. 38)
INDEX button (p. 116)
SLIDE SHOW button (p. 116)
Zoom buttons (p. 30)
CARD
buttons (p. 115)
Select buttons (p. 43)
14
Using a Household Power Source
You can operate the camcorder from a household power source using the supplied
power adapter. The power adapter converts current from a power outlet (100-240 V
AC, 50/60 Hz) to the DC current used by the camcorder.
E
1. Turn the POWER switch to OFF.
2. Connect the power cord to the
power adapter.
3. Plug the power cord into a power
outlet.
r
q
4. Connect the power adapter to the
camcorder’s DC IN terminal.
w
e
5. After use, turn off the camcorder and disconnect the power adapter
from the camcorder. Unplug the power cord from the power outlet and
disconnect it from the adapter.
❍ Turn off the camcorder before connecting or disconnecting the power adapter.
❍ If the adapter is used close to a TV, it may cause picture interference. Move the
adapter away from the TV or the antenna cable.
❍ Do not connect any products that are not expressly recommended to the
camcorder’s DC IN terminal or to the power adapter.
❍ You may hear some noise from the power adapter during use. This is not a
malfunction.
15
Attaching and Charging the Battery Pack
Charge the battery pack with the supplied power adapter before you use the
camcorder for the first time and subsequently when the message “CHANGE THE
BATTERY PACK” appears.
E
1. Turn the POWER switch to OFF.
q
w
2. Move the viewfinder upward.
3. Attach the battery pack to the
camcorder.
• Remove the terminal cover of the battery
pack.
• Align the end of the battery pack with the
e
line on the camcorder, press lightly and slide
it in the direction of the arrow until it clicks.
click
4. Connect the power cord to the
adapter.
CHARGE indicator
5. Plug the power cord into a power
outlet.
6. Connect the power adapter to the
camcorder’s DC IN terminal.
7. When charging is complete,
disconnect the power adapter from
the camcorder. Unplug the power
cord from the power outlet and
disconnect it from the adapter.
8. Remove the battery pack after use.
Press the BATT. button to remove the battery.
DC IN terminal
y
r
t
❍ The battery pack may be defective when the CHARGE indicator flashes rapidly.
❍ The CHARGE indicator informs you about the charge status.
0-50%:
More than 50%: Flashes twice every second
100%: Glows steadily
Flashes once every second
❍ Do not disconnect and reconnect the power cord while charging a battery
pack. The battery pack may not be charged correctly even if the CHARGE
indicator glows steady. The battery pack may also not be charged correctly
when a power outage occurs during charging. Remove the battery pack and
attach it back to the camcorder.
16
Charging, Recording and Playback Time
Below times are approximate and vary according to the charging, recording or
playback conditions.
E
Charging Time
Battery Pack
Charging Time
110 min.
BP-508 (OPTURA10)
BP-512 (OPTURA20/optional)
BP-511 (Optional)
BP-522 (Optional)
BP-535 (Optional)
120 min.
120 min.
210 min.
310 min.
• Charge the battery pack in temperatures between 41º F and 104º F (5º C and 40º C).
• A lithium ion battery pack can be charged at any charge state. Unlike conventional
battery packs, you do not need to completely use or discharge it before charging.
Recording Time
Battery Pack
Maximum Recording Time
Typical Recording Time*
Using the viewfinder Using the LCD Using the viewfinder Using the LCD
BP-512 (Supplied)
BP-511 (Optional)
BP-522 (Optional)
BP-535 (Optional)
150 min.
150 min.
320 min.
520 min.
110 min.
110 min.
230 min.
370 min.
80 min.
80 min.
175 min.
280 min.
60 min.
60 min.
125 min.
200 min.
BP-508 (Supplied)
BP-512 (Optional)
BP-511 (Optional)
BP-522 (Optional)
BP-535 (Optional)
80 min.
150 min.
150 min.
320 min.
520 min.
65 min.
115 min.
115 min.
235 min.
375 min.
45 min.
80 min.
80 min.
175 min.
280 min.
35 min.
65 min.
65 min.
130 min.
205 min.
* Approximate times for recording with repeated operations such as start/stop, zooming, power
on/off. Actual time may be shorter.
• We recommend that you prepare battery packs 2 to 3 times longer than you think you
might need.
• To conserve battery charge, turn off the camcorder instead of leaving it in record pause
mode.
Playback Time
Battery Pack
(Using the LCD)
BP-508 (OPTURA10)
BP-512 (OPTURA20/optional)
BP-511 (Optional)
–
70 min.
140 min.
140 min.
295 min.
470 min.
130 min.
130 min.
260 min.
430 min.
BP-522 (Optional)
BP-535 (Optional)
17
How much power is left?
The battery symbols indicate the charge status of the battery
pack.
E
When the battery pack is empty, “CHANGE THE BATTERY PACK”
appears for 4 seconds and
starts flashing.
The battery charge indicators are not constant – they vary
according to the condition under which battery pack and
camcorder are used.
Battery Pack Handling Precautions
DANGER!
Treat the battery pack with care.
• Keep it away from fire (or it might explode.)
• Do not expose the battery pack to temperature higher than 140º F (60º C). Do
not leave it near a heater or inside a car in hot weather.
• Do not try to disassemble or modify it.
• Do not drop or knock it.
• Do not get it wet.
❍ Charged battery packs continue to discharge naturally. Therefore, charge them on
the day of use, or the day before, to ensure a full charge.
❍ Attach the terminal cover whenever a battery pack is not in use. Contact to metallic
objects may cause a short circuit and damage the battery pack.
❍ Dirty terminals may cause a poor contact between the battery pack and the
camcorder. Wipe the terminals with a soft cloth.
❍ Since storing a charged battery pack for a long time (about 1 year) can shorten its
lifecycle or affect performance, we recommend to discharge the battery pack fully
and to store it in a dry place at temperatures no higher than 86˚ F (30˚ C). If you do
not use the battery pack for long periods, charge and discharge it fully at least once
a year. If you have more than 1 battery pack, perform these precautions at the
same time for all battery packs.
❍ Although the battery pack’s operating temperature range is from 32˚ F to 104˚ F
(0˚ C to 40˚ C), the optimal range is from 50˚ F to 86˚ F (10˚ C to 30˚ C). At cold
temperatures, performance will temporarily decline. Warm it in your pocket before
use.
❍ Replace the battery pack if the usable time after full charge diminishes substantially
at normal temperatures.
18
Installing the Backup Battery
The backup battery allows the camcorder to retain date, time and other camcorder
settings while the power source is disconnected. Power the camcorder from a
household power source or with a battery pack when replacing the backup battery to
retain the setting.
E
1. Open the backup battery cover.
q
w
e
2. Insert the lithium battery with the
+ side facing outward.
3. Close the cover.
WARNING!
• The battery used in this device may present a fire or chemical burn hazard if
mistreated. Do not recharge, disassemble, heat above 212° F (100° C) or
incinerate the battery.
• Replace the battery with a CR2025 made by Panasonic, Hitachi Maxell, Sony,
Sanyo, or with Duracell2025. Use of other batteries may present a risk of fire or
explosion.
❍ Do not pick up the battery using tweezers or other metal tools as this will
cause a short circuit.
❍ Wipe the battery with a clean dry cloth to ensure proper contact.
❍ Keep the battery out of reach of children. If it is swallowed, seek medical
assistance immediately. The battery case may break and the battery fluids may
damage stomach and intestines.
❍ Do not disassemble, heat or immerse the battery in water to avoid the risk of
explosion.
The backup battery has a life span of about a year. j flashes to inform you that
it needs to be replaced.
19
Preparing the Camcorder
Adjusting the Viewfinder (Diopter Adjustment)
1. Turn on the camcorder and keep the
LCD panel closed to adjust the
E
viewfinder.
2. Adjust the diopter adjustment lever.
Do not leave the viewfinder exposed to direct sunlight as it may melt (due to
concentration of light by the lens). Adjust the angle of the viewfinder to prevent
sunlight from entering.
Attaching the Lens Cap
1. Attach the cord to the lens cap.
2. Pass the grip belt through the loop
on the cord.
Press the buttons on the lens cap when
attaching/removing it. Hook the lens cap on
the grip belt while you are recording, and
place it over the lens when you have finished.
Fastening the Grip Belt
Hold the camcorder with your right
hand and adjust the belt with your left.
Adjust the grip belt so that you can reach the
zoom lever and photo button with your index
finger, and the start/stop button with your
thumb.
20
Attaching the Shoulder Strap
For extra security and portability, attach the shoulder strap before using the
camcorder.
E
Pass the ends through the strap mount
and adjust the length of the strap.
Removing and Attaching the Accessory Shoe Cover
Remove the accessory shoe cover when attaching an accessory to the advanced
accessory shoe.
1. Lift the cover with your nail and
remove the cover.
Hook the cover on the lens cap cord or grip
belt while using the accessory shoe.
2. Insert the end into the accessory
shoe and attach it onto the shoe.
21
Loading a Cassette
Use only videocassettes marked with the D logo.
E
Loading and Unloading
1. Slide and hold the OPEN/EJECT
switch and open the cassette
w
Tape
compartment cover.
protection tab
q
The cassette compartment opens
automatically.
2. Load/unload the cassette.
• Load the cassette with the window facing
the grip belt and the REC/SAVE tab facing
upward.
• Unload the cassette by pulling it straight
out.
e
3. Press the P mark on the cassette
compartment until it clicks.
P U S H
Wait for the cassette compartment to retract
automatically.
4. Close the cassette compartment
cover.
click
r
❍ Do not interfere with the cassette compartment while it is opening or closing
automatically or attempt to close the cover until the cassette compartment has
fully retracted.
❍ Be careful not to get your fingers caught in the cassette compartment cover.
❍ If the camcorder is connected to a power source, cassettes can be
loaded/unloaded even if the POWER switch is set to OFF.
❍ v flashes if no cassette is inserted when turning on the power (in CAMERA
and PLAY (VCR) mode).
❍ With some types of tapes, the remaining tape display may not be accurate.
22
Protecting Tapes from Accidental Erasure
To protect your recordings from accidental
erasure, slide the tab on the cassette to the
left. (This switch position is usually labeled
SAVE or ERASE OFF.)
E
REC
SAVE
REC
SAVE
If you load a protected cassette in CAMERA
mode, the message “THE TAPE IS SET FOR
ERASURE PREVENTION” appears for approx. 4
seconds and v starts flashing. If you wish to record on that cassette, slide the tab
back to the right.
Cassette Handling Precautions
❍ Rewind tapes after use. If the tape becomes slack and damaged, it may cause picture
and sound distortion.
❍ Return cassettes in the case and store them upright.
❍ Do not leave the cassette in the camcorder after use.
❍ Do not use spliced tapes or nonstandard cassettes as they may damage the camcorder.
❍ Do not use tapes that have been jammed as video heads may become dirty.
❍ Do not insert anything into the small holes of the cassette, or cover them with
cellophane tape.
❍ Handle cassettes with care. Do not drop or subject them to severe impact as this may
damage the cassettes.
❍ Rewind tapes from time to time if they are stored for a long time.
❍ With cassettes equipped with a memory function, metal plated terminals may become
dirty with use and the cassette’s memory function may not work properly. Clean the
terminals with a cotton swab after about 10 times of loading/unloading.
23
Using the Wireless Controller
You can operate the camcorder with the
supplied wireless controller from a distance of
up to 16 feet (5 m). Point it at the camcorder’s
remote sensor when you press the buttons.
E
Following functions cannot be operated
without the wireless controller:
• Some special playback modes (
38)
• Photo/date search (
• Zero set memory (
86)
87)
• AV Insert (
• Audio dubbing (
❍ Camcorder and wireless controller are equipped with 2 remote sensor modes
48). If the wireless controller does not work, check if camcorder and
95)
97)
(
wireless controller are set to the same mode.
❍ The wireless controller may not work properly in bright places, such as
outdoors under direct sunlight, or when used too close to the camcorder.
❍ The operable range of the wireless controller may shorten when the
camcorder’s remote sensor is exposed to strong light.
❍ When the batteries run out, replace both at the same time.
Inserting Batteries
The wireless controller operates with two AA batteries.
1. Open the battery cover.
2. Insert the batteries following the +
and – markings.
q
w
3. Close the battery cover.
e
24
Setting the Time Zone, Date and Time
Set the time zone, date and time when you first start using your camcorder. Install the
E
backup battery before you begin (
19).
Setting the Time Zone/Daylight Saving Time
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
SYSTEM
T.ZONE/DST•••N.Y.
(
43)
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [SYSTEM] and press
the selector dial.
3. Turn the selector dial to select [T.ZONE/DST] and
press the selector dial.
• The time zone setting appears.
• The default setting is New York. Select your time zone and daylight saving time (DST)
setting if necessary.
4. Turn the selector dial to select the setting option that represents your
time zone.
To adjust for daylight saving time, select the time zone with the U next to the area.
5. Press the MENU button to close the menu.
25
16
1
4
E
20
19
2
18
24
3
17
6
7
9
10
15
8
5
21
23
14
12
22
11
13
14 15 16 17 18 19 20 21 22 23 24
1
2
3
4
5
6
7
8
9
10 11 12 13
No.
No.
Time zone
LONDON
PARIS
Time zone
WELLGTN (Wellington)
SAMOA
CAIRO
HONOLU. (Honolulu)
ANCHOR. (Anchorage)
L.A. (Los Angeles)
DENVER
MOSCOW
DUBAI
KARACHI
DACCA
CHICAGO
BANGKOK
H. KONG (Hong Kong)
TOKYO
N.Y. (New York)
CARACAS
RIO (Rio de Janeiro)
SYDNEY
SOLOMON
FERNAN. (Fernando de Noronha)
AZORES
❍ Once you have set time zone, date and time, you do not need to reset the
clock each time you travel to another time zone. Just set the time zone to the
one of your destination, and the camcorder automatically adjusts the clock.
❍ Days per month and leap years will be automatically adjusted.
Setting the Date and Time
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
D/TIME SET•••JAN. 1,2003
12:00 PM
SYSTEM
(
43)
1. Press the MENU button to open the menu.
26
2. Turn the selector dial to select [SYSTEM] and press
the selector dial.
3. Turn the selector dial to select [D/TIME SET] and
press the selector dial.
E
The year display starts to flash.
4. Turn the selector dial to select the year, and press the selector dial.
• The next part of the display starts flashing.
• Set the month, day, hours and minutes in the same way.
5. Press the MENU button to close the menu and to
start the clock.
Time zone, date and time appear for 4 seconds each time you
turn the power on.
❍ To change a part of the date or time, press the selector dial at step 4, and
move to the part you wish to change.
❍ The date can be set to any year between 2003 and 2030.
Displaying Date and Time during Recording
You can display time zone, date and time in the lower left corner of the screen (the
time zone disappears after 4 seconds). The 4-second display will no longer appear
when you turn the power on. The date and time display will not be superimposed on
your recordings.
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
DISPLAY SET UP
D/T DISPLAY••OFF
(
43)
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [DISPLAY SET UP] and
press the selector dial.
3. Turn the selector dial to select [D/T DISPLAY] and
press the selector dial.
4. Turn the selector dial to select [ON].
5. Press the MENU button to close the menu.
27
Recording Movies on a Tape
You can use the LCD screen or the viewfinder when recording. Adjust the angle of the
LCD panel or viewfinder for comfortable recording.
E
Before You Begin Recording
Make a test recording first to check if the camcorder operates correctly. Before you
make important recordings, clean the video heads (
148).
Preparations
Connect a power source. Load a cassette.
Recording
1. Remove the lens cap.
2. Set the camcorder to CAMERA mode.
w
If you have not set the time zone, date and
time, “SET THE TIME ZONE, DATE AND TIME”
appears. See Setting the Time Zone, Date and
q
Time (
25).
w
3. Open the LCD panel (
32).
To use the viewfinder, keep the LCD panel
closed or rotate it so that the screen faces in
r t
the same direction of the lens (
33).
4. Press the start/stop button to begin
recording.
Wait until the tape counter came to a
complete stop before you begin recording.
5. Press the start/stop button again to
pause recording.
e
Restart recording by pressing the start/stop button.
28
When You Have Finished Recording
1. Turn the POWER switch to OFF.
2. Close the LCD panel and return the viewfinder to its original position.
3. Replace the lens cap.
E
4. Unload the cassette.
5. Disconnect the power source.
When recording outdoors or through a window, do not leave LCD screen,
viewfinder or lens exposed to direct sunlight as it may cause damage.
❍ Turn the power off if you do not intend to use the camcorder for a longer
time.
❍ When you start recording, the camcorder counts from 1 second to 10 seconds
(recording reminder). Recordings shorter than 10 seconds may be difficult to
edit later. On the other hand, a recording not containing a particular action
should generally last no longer than 10 seconds.
❍ The camcorder will shut off after 5 minutes when left in record pause mode to
protect tape and video heads. “ AUTO POWER OFF” appears 20 seconds
before shutoff. To continue recording, turn the POWER switch to OFF and then
back to CAMERA.
❍ For when to use the [ (Easy Recording) or Q (program AE) mode, see Using
the Recording Programs (
55).
❍ When you do not remove the cassette, you can record the next scene without
producing any noise or blank sections between the recordings even if you turn
the camcorder off.
❍ About the built-in microphone: When recording near loud sounds (such as
fireworks, drums or concerts), sound may become distorted or may be
recorded not in the actual sound level.
❍ For extra recording time, see Changing the Recording Mode (
52).
About the LCD and viewfinder screen: The screens are produced with extremely
high-precision manufacturing techniques, with more than 99.99% of the pixels
operating to specification. Less than 0.01% of the pixels may occasionally misfire or
appear as black or green dots. This has no effect on the recorded image and does
not constitute a malfunction.
29
Zooming
The camcorder’s zoom lens allows you to choose the best picture angle for your
recordings. The camcorder automatically switches between optical zooming and
digital zooming. Image resolution is slightly lower with the digital zoom.
E
Zoom in
T
W
Zoom out
16× Optical Zoom (Card: 15×)
Move the zoom lever toward W to zoom out (wide-
angle). Move it toward T to zoom in (telephoto).
• Press the zoom lever slightly for a slow zoom. Press harder for a
faster zoom.
• You can also use the T and W buttons on the wireless controller.
However, you cannot control the zoom speed.
64×/320× Digital Zoom (Card: 60×)
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
CAMERA SET UP
D.ZOOM•••••••64×
(
43)
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [CAMERA SET UP] and
press the selector dial.
3. Select [D.ZOOM] and press the selector dial.
4. Select a setting option.
5. Press the MENU button to close the menu.
30
❍ Keep at least 3.3 ft. (1 m) to the subject. At wide-angle, you can focus on a
subject as close as 0.39 in. (1 cm).
❍ A zoom indicator appears for 4 seconds. It extends in light blue when the
digital zoom is set to 64×, and extends further in dark blue when set to 320×.
❍ Digital zoom cannot be used in the Night mode and Super Night (OPTURA20)
mode.
E
❍ Digital zoom cannot be used when the multi-image screen is selected.
❍ Because the image stabilizer cannot be used in CARD CAMERA mode, we
recommend mounting the camcorder on a tripod at large magnifications.
31
Using the LCD Screen
1. Push the OPEN button at the LCD
panel and open the LCD panel.
E
The LCD screen switches on and the
viewfinder switches off.
2. Rotate the LCD panel and choose the
angle of the screen.
You can rotate the LCD panel so that the
screen faces in the same direction as the lens
(
33), or push it flat against the camcorder with the screen facing outward.
3. Close the LCD panel after use.
• Close the LCD panel firmly until it clicks.
• The LCD screen switches off and the
viewfinder switches on.
❍ Make sure to open the LCD panel at 90 degrees before rotating it.
❍ Rotate the LCD panel in the vertical position before closing the LCD panel.
❍ When recording outdoors or through a window, do not leave the LCD screen,
viewfinder or lens exposed to direct sunlight as it may cause damage.
❍ Do not hold the camcorder by the LCD panel or the viewfinder.
❍ Bright light or reflected light may cause a vertical light bar to appear on the
screen. This is not a malfunction.
❍ Bright light may make it difficult to use the LCD screen. In such case, use the
viewfinder instead.
32
Adjusting the Brightness of the LCD Screen
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
–
BRIGHTNESS•••
+
DISPLAY SET UP
(
43)
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [DISPLAY SET UP] and
press the selector dial.
3. Turn the selector dial to select [BRIGHTNESS] and
press the selector dial.
4. Turn the selector dial and adjust the level.
Turn the selector dial up to make the screen brighter and down to make it darker.
5. Press the MENU button to close the menu.
Changing the brightness of the LCD screen does not affect that of the viewfinder
or the recordings.
Allowing the Subject to Monitor the LCD Screen
You can rotate the LCD panel so that the
screen faces in the same direction as the lens.
The viewfinder switches on allowing you to
use the viewfinder while the subject can
monitor the screen.
When you rotate the screen so that the screen faces in the same direction as the lens,
the image appears mirror reversed (LCD MIRROR ON). However, you can choose to
display the image as it is being recorded (LCD MIRROR OFF).
33
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
DISPLAY SET UP
LCD MIRROR•••ON
E
(
43)
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [DISPLAY SET UP] and
press the selector dial.
3. Turn the selector dial to select [LCD MIRROR] and
press the selector dial.
4. Turn the selector dial to select [OFF].
5. Press the MENU button to close the menu.
When [LCD MIRROR] is set to [ON], most screen displays appear mirror reversed.
34
Searching and Reviewing when Recording
REC SEARCH – button/
v (record review) button
REC SEARCH + button
E
Record Review
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CAMERA
In record pause mode, this function allows you to review the last few seconds of your
recording to check if it has been recorded properly.
Press and release the c (record review) button.
The camcorder rewinds the tape, plays back the last few seconds,
and returns to record pause mode.
Record Search
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CAMERA
In record pause mode, this function allows you to play back the tape (forward or
reverse) to locate the point where you wish to begin recording.
Press and hold the REC SEARCH + button (forward) or –
button (reverse).
• Release the button at the point you wish to begin recording.
• The camcorder returns to record pause mode.
❍ Noise may appear on the screen when you play back the tape in reverse.
❍ There will be no sound during Record Review and Record Search.
35
Tips for Making Better Videos
Holding the Camcorder
E
For maximum stability, grip the camcorder in your right hand and keep your right
elbow pressed against your body. If necessary, support the camcorder with your left
hand. Be careful that your fingers do not touch the microphone or lens.
Low-angle Recording
High-angle Recording
For More Stability
Lean against a wall
Put the camcorder on a table
Lie on your elbow
Use a tripod
Lighting
When recording outdoors, we recommend
recording with the sun at your back.
❍ When using a tripod, do not leave the viewfinder exposed to direct sunlight as
it may melt (due to concentration of the light by the lens).
❍ Do not use tripods with fastening screws longer than 0.2 inch (5.5 mm) as it
may damage the camcorder.
36
Playing Back a Tape
When you use the LCD screen for playback, the camcorder plays back the sound via
built-in speaker. The built-in speaker is monaural. Use headphones for stereo sound or
when using the viewfinder for playback.
E
Preparations
Connect a power source. Load a cassette.
Playback
1. Set the camcorder to PLAY (VCR)
mode.
q
2. Open the LCD panel.
t
e
You can also close the LCD panel with the
screen facing outward.
r
3. Press the ` button to rewind the
tape.
To fast forward the tape, press the 1
button. To stop playback, press the 3 button.
4. Press the e/a button to begin
playback.
w
5. Press the 3 button to stop playback.
❍ If the playback picture is distorted, clean the video heads using a Canon Head
Cleaning Cassette or a commercially available digital video head-cleaning
cassette (
❍ To use the viewfinder, close the LCD panel. The built-in speaker does not
sound. Use headphones when using the viewfinder ( 39).
❍ For displaying the date and time during playback, see Displaying the Data Code
84).
148).
(
37
Special Playback Modes
Special playback modes (except of playback pause and fast/rewind playback) can only
be operated with the wireless controller.
E
` (rewind) button
1 (fast forward) button
REW
PLAY
STOP
FF
PAUSE SLOW
2
e/a (play/pause)
button
3 (stop) button
e/a (Playback Pause)
To pause playback, press the e/a button. Press the e/a button to resume playback.
The camcorder goes into stop mode after 5 minutes in playback pause mode.
1 (Fast Forward Playback) / ` (Rewind Playback)
Plays back the tape at 9.5 times normal speed (forward or reverse). Press and hold the
button during normal playback or fast forward.
+/ae (Frame Advance) / –/4a (Frame Reverse)
Plays back frame-by-frame. Press the button repeatedly during playback pause. Press
and hold it to play back continuous frame advance/frame reverse.
SLOW I (Slow Forward)/(Slow Reverse)
Plays back at about 1/3 normal speed. For slow forward playback, press the SLOW M
button. For slow reverse playback, press the –/4a button followed by the SLOW M
button. Press the e (play) button to return to normal playback.
–/4a (Reverse Playback)
Plays back in reverse at normal speed. Press the button during normal playback. Press
the e (play) button return to normal playback. The camcorder goes into stop mode
after 5 minutes in reverse playback pause.
× 2 (Forward× 2 Playback)/(Reverse 2× Playback)
Plays back at 2 times normal speed. Press the button during normal or reverse
playback. Press the e (play) button return to normal playback.
❍ There is no sound during special playback.
❍ The picture may become distorted during some special playback modes.
38
Playing Back with the Built-in Speaker/Headphones
E
H (phones) terminal
Selector dial
Built-in speaker
❍ When using the built-in speaker, make sure that “H” is not displayed on the
screen. When using the headphones, make sure that “H” is displayed. Change
the setting as necessary (
70).
❍ The built-in speaker does not sound when “H” is displayed.
❍ Do not connect headphones unless “H” is displayed as it produces noise.
❍ The built-in speaker is monaural. Use headphones for stereo sound.
❍ The setting has to be done separately for each operating mode. Make sure to
change the setting when you have change the operating mode.
Adjusting the Volume
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY (VCR)
Turn the selector dial up to increase the volume, and
down to lower the volume.
• A volume bar appears for 4 seconds.
• You can turn off the volume completely by turning the selector
dial down until [OFF] appears. Turn the selector dial up to increase the volume again.
❍ Sound may become distorted when the volume is turned up too high.
❍ The headphone volume can be adjusted in all operating modes.
❍ The camcorder retains the setting even if you turn it off (separately for
headphones and built-in speaker).
❍ See also Using Headphones during Recording (
70).
39
Playing Back on a TV Screen
You can connect the camcorder to a TV or VCR to play back your recordings on a TV
screen.
E
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change
the setting (
70).
❍ When you use the TV as a monitor during recording, keep the TV volume
turned down as long as the camcorder’s audio terminals are connected. An
unpleasant high-pitched squeal, called feedback, may be produced if sound
from the TV speakers is picked up by the microphone.
❍ For high picture quality, we recommend using a TV with an S (S1) terminal.
❍ TVs with S1-terminal or Video ID-1 system: Recordings made in the 16:9 mode
(
50) will be automatically played back in wide screen mode.
TVs with S (S1)-Video Input Terminal
Refer also to the TV or VCR instruction manual.
INPUT
Signal flow
S(S1)-VIDEO
S-150 S-video Cable (optional)
VIDEO
AUDIO
L
Signal flow
R
STV-250N Stereo Video Cable (supplied)
1. Turn off all devices before starting the connections.
2. Connect the S-150 S-video Cable (optional) to the S-video terminals.
40
3. Connect the STV-250N Stereo Video Cable to the camcorder’s AV
terminal and the audio terminals of the TV/VCR.
Connect the white plug to the white AUDIO terminal L (left), and the red plug to the
red AUDIO terminal R (right). Do not connect the yellow plug.
E
4. If connecting to a TV, set the input selector to VIDEO. If connecting to a
VCR, set the input selector to LINE.
TVs with Audio/Video Terminals
Refer also to the TV or VCR instruction manual.
VIDEO
AUDIO
L
R
Signal flow
STV-250N Stereo Video Cable (supplied)
1. Turn off all devices before starting the connections.
2. Connect the STV-250N Stereo Video Cable to the camcorder’s AV
terminal and the audio/video terminals on the TV/VCR.
Connect the white plug to the white audio terminal L (left), the red plug to the red
audio terminal R (right) and the yellow plug to the yellow video terminal VIDEO.
3. If connecting to a TV, set the input selector to VIDEO. If connecting to a
VCR, set the input selector to LINE.
41
Selecting the Audio Output Channel
You can select the output channels when playing back a tape with audio recorded on
two channels.
E
CAMERA
CARD CAMERA
CARD PLAY (VCR)
PLAY (VCR)
AUDIO SET UP
OUTPUT CH••••L/R
(
43)
1. Press the MENU button to open the menu.
2. Turn the selector dial to select [AUDIO SET UP] and
press the selector dial.
3. Turn the selector dial to select [OUTPUT CH] and
press the selector dial.
4. Turn the selector dial to select a setting option.
• L/R: Stereo: L+R channels, Bilingual: Main+Sub.
• L/L: Stereo: L channel, Bilingual: Main.
• R/R:Stereo: R channel, Bilingual: Sub.
5. Press the MENU button to close the menu.
The setting resets to the L/R setting when you turn the camcorder off.
42
Menus and Settings
Many of the camcorder’s advanced functions are selected from menus that appear on
the screen.
E
Selecting Menus and Settings
1. Set the camcorder to the correct operating mode.
2. Press the MENU button to open the menu.
3. Turn the selector dial to select a submenu and press
the selector dial.
4. Turn the selector dial to select a menu item and
press the selector dial.
5. Turn the selector dial to select a setting option.
6. Press the MENU button to close the menu.
When setting the white balance or shutter speed, press the
selector dial first before pressing the MENU button.
❍ Pressing the MENU button at any time closes the menu.
❍ Selecting [[ RETURN] takes you back one level.
❍ When the submenu consists of 2 pages, select [NEXT PAGE] to move to the
second page, and [PREV PAGE] to return to the first page.
❍ Items that are not available appear in purple.
❍ You may find it more convenient to use the wireless controller to operate the
menu. Press the MENU button on the wireless controller to open or close the
menu. Use the select buttons in place of the selector dial and press the SET
button in place of pressing the selector dial.
43
Menu and Default Settings
Default settings are shown in boldface.
CAMERA Menu (CAM. MENU)
E
PLAY (VCR)
CARD CAMERA
CARD CAMERA
CAMERA
Submenu
\CARD MIX
Menu Item
MIX TYPE
Setting Options
CARD CHROMA, CARD LUMI.,
CAM. CHROMA, C. ANIMATION
CORNER, STRAIGHT, RANDOM
130
130
ANIMAT. TYPE
MIX LEVEL
130
79
CAMERA SET UP SHUTTER
D. ZOOM
AUTO, 1/60, 1/100, 1/250, 1/500, 1/1000,
1/2000, 1/4000, 1/8000
OFF, 64 ,
30
67
82
73
77
50
110
52
39
69
69
70
33
34
140
27
51
48
50
25
26
49
49
49
49
× 320×
IMAGE S. i
WHITE BAL.
ON, OFF
AUTO, SET W, INDOOR T, OUTDOOR U
(FLASH)
AUTO , RED-EYE
AUTO, OFF
ON, OFF
, FLASH ON , FLASH OFF
(AF AST LAMP*)
16:9
PHOTO REC
REC MODE
AV/PHONES
WIND SCREEN
AUDIO MODE
H VOLUME
TAPE , CARD
SP, LP
VCR SET UP
AV, PHONES H
ON, OFF
AUDIO SET UP
16bit, 12bit
DISPLAY SET UP BRIGHTNESS
LCD MIRROR
ON, OFF
TV SCREEN
ON, OFF
D/T DISPLAY
ON, OFF
DEMO MODE
ON, OFF
SYSTEM
WL. REMOTE
BEEP
A1, A2, OFF B
ON, OFF
T.ZONE/DST
D/TIME SET
SHTR SOUND
S-UP SOUND
S/STOP SOUND
SELF-T SOUND
See list of time zones
MY CAMERA
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
*OPTURA20 only
44
(
): Appears when you connect the optional VFL-1 Video Flash Light and set it to ON.
PLAY (VCR) Menu (VCR MENU)
CAMERA
CARD CAMERA
Setting Options
CARD CAMERA
PLAY (VCR)
Submenu
VCR SET UP
Menu Item
REC MODE
E
SP, LP
52
39
AV/PHONES
AV \ DV OUT
OUTPUT CH
AUDIO DUB.
WIND SCREEN
AUDIO MODE
12bit AUDIO
MIX BALANCE
SI QUALITY
AV, PHONES H
ON, OFF
94
AUDIO SET UP
L/R, L/L, R/R
42
AUDIO IN, MIC. IN
ON, OFF
98
69
16bit, 12bit
69
STEREO1, STEREO2, MIX/FIXED, MIX/VARI.
99
99
CARD SET UP
SUPER FINE, FINE, NORMAL
320 × 240, 160 × 120
RESET, CONTINUOUS
CANCEL, EXECUTE
102
103
104
132
33
MOVIE SIZE
FILE NOS.
CARD
OPERATIONS
COPY
\
DISPLAY SET UP BRIGHTNESS
DISPLAYS
ON, OFF <PLAYBK>
ON, OFF
140
85
6SEC. DATE
DATA CODE
DATE/TIME, CAMERA DATA, CAM. & D/T
DATE, TIME, DATE & TIME
A1, A2, OFF B
ON, OFF
85
D/TIME SEL.
85
SYSTEM
WL. REMOTE
BEEP
48
50
T.ZONE/DST
D/TIME SET
SHTR SOUND
S-UP SOUND
S/STOP SOUND
SELF-T SOUND
See list of time zones
25
26
MY CAMERA
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
49
49
49
49
45
CARD CAMERA Menu (C. CAM. MENU)
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
Setting Options
CARD CAMERA
E
Submenu
Menu Item
CAMERA SET UP SHUTTER
D.ZOOM
AUTO, 1/60, 1/100, 1/250
79
OFF, 60×
30
81
WHITE BAL.
DRIVE MODE
(FLASH)
AUTO, SET W, INDOOR T, OUTDOOR U
CONT. , AEB
, SINGLE
107
73
AUTO , RED-EYE , FLASH ON , FLASH OFF
AUTO, OFF
(AF AST LAMP*)
FOCUS PRI.
ND
77
ON, OFF
107
106
102
102
103
104
39
AUTO, OFF
CARD SET UP
SI QUALITY
SI SIZE
SUPER FINE, FINE, NORMAL
1280 × 960, 640 × 480
320 × 240, 160 × 120
RESET, CONTINUOUS
AV, PHONES H
MOVIE SIZE
FILE NOS.
VCR SET UP
AV/PHONES
WIND SCREEN
H VOLUME
AUDIO SET UP
ON, OFF
69
70
DISPLAY SET UP BRIGHTNESS
LCD MIRROR
33
ON, OFF
34
TV SCREEN
ON, OFF
140
27
D/T DISPLAY
ON, OFF
DEMO MODE
ON, OFF
51
SYSTEM
WL. REMOTE
BEEP
A1, A2, OFF B
ON, OFF
48
50
T.ZONE/DST
D/TIME SET
SHTR SOUND
S-UP SOUND
S/STOP SOUND
SELF-T SOUND
See list of time zones
25
26
MY CAMERA
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
49
49
49
49
*OPTURA20 only
(
): Appears when you connect the optional VFL-1 Video Flash Light and set it to ON.
46
CARD PLAY (VCR) Menu (C.PLAY MENU)
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
Submenu
CARD
OPERATIONS
Menu Item
COPY
Setting Options
CANCEL, EXECUTE
\
133
(Single Image
PRINT ORDERS
ALL ERASE
YES, NO
121
Display)
IMAGE ERASE
FORMAT
CANCEL, SINGLE, ALL
119
134
118
120
52
CANCEL, EXECUTE
\
CARD
OPERATIONS
(Index Screen)
PROTECT
\
PRINT ORDER
VCR SET UP
REC MODE
AV/PHONES
SP, LP
AV, PHONES H
39
DISPLAY SET UP BRIGHTNESS
DISPLAYS
33
ON, OFF <PLAYBK>
DATE, TIME, DATE & TIME
A1, A2, OFF A
ON, OFF
140
85
D/TIME SEL.
SYSTEM
WL. REMOTE
BEEP
48
50
T.ZONE/DST
D/TIME SET
See list of time zones
25
26
136
49
MY CAMERA
CREATE START-UP IMAGE
SEL. S-UP IMG
SHTR SOUND
S-UP SOUND
S/STOP SOUND
SELF-T SOUND
NO IMAGE, CANON LOGO, MY IMAGE1,
MY IMAGE2
PATTERN1, PATTERN2, PATTERN3
49
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
PATTERN1, PATTERN2, PATTERN3
49
49
49
\
PRINT
Appears when connecting a printer with direct print function.
127
47
Changing the Remote Sensor Mode
Two remote sensor modes and an off setting are available to prevent interference
from other Canon wireless controllers being used nearby.
E
Turning the Remote Sensor Off
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
SYSTEM
WL.REMOTE•••
•
1
(
43)
Open the menu and select [SYSTEM]. Select [WL.
REMOTE], set it to [OFF B] and close the menu.
“B“ appears.
Changing the Remote Sensor Mode
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
SYSTEM
WL.REMOTE••••
1
(
43)
1. On the camcorder, open the menu and select
[SYSTEM]. Select [WL. REMOTE], set it to [A 2] and
close the menu.
The selected mode appears for 4 seconds.
2. On the wireless controller, press and hold the
REMOTE SET button. Press the ZOOM T button for
mode 2. Keep the button pressed for over 2 seconds.
AUDIO DUB. PAUSE
SLOW
2
AV INSERT AV DV REMOTE SET
REC
PAUSE
-
WIRELESS CONTROLLER WL D79
If you have set the camcorder to mode 1, press the ZOOM W
button for mode 1.
START
/STOP
ZOOM
W
T
PHOTO
SELF T. D.EFFECT.
MENU
SET
ON/OFF
TV SCREEN
❍ The wireless controller returns to mode 1 when you
replace the batteries. Change the mode if necessary.
❍ Make sure that camcorder and wireless controller are set to the same mode.
Display the camcorder’s mode by pressing any button on the wireless controller
(except of the REMOTE SET button) and set the wireless controller’s mode to
the same mode. Change the batteries if the wireless controller still does not
work.
48
Customizing the Camcorder
You can personalize your camcorder by customizing the start-up image and the sound
it makes for start-up, shutter, start/stop and self-timer (collectively called the My
Camera settings). You can also create your own start-up image. See Creating a Start-
E
up Image (
136).
Changing the My Camera Settings
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
MY CAMERA
SHTR SOUND•••PATTERN1
S–UP SOUND•••PATTERN1
S/STOP SOUND•PATTERN1
SELF–T SOUND•PATTERN1
(
43)
1. Open the menu and select [MY CAMERA].
2. Select the menu item you wish to change.
• When selecting a start-up image (only in CARD PLAY (VCR) mode): [NO IMAGE],
[CANON LOGO], [MY IMAGE1] and [MY IMAGE2] appears.
• When selecting a sound: [PATTERN1], [PATTERN2] and [PATTERN3] appear.
3. Select a setting option and close the menu.
49
Other Camcorder Settings
Beep
E
You will hear a beep upon camcorder operations such as power on/off, start/stop, self-
timer countdown, automatic shut-off, and unusual conditions of the camcorder. The
beep will not be recorded.
If you turn off the beep, all camcorder sounds including the ones of the My Camera
settings will be turned off.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
SYSTEM
BEEP•••••••••ON
(
43)
To turn the beep off, open the menu and select [SYSTEM]. Select [BEEP],
set it to [OFF] and close the menu.
Recording in 16:9 (Wide Screen TV Recording)
You can record in the 16:9 format for playback on wide screen TVs.
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CAMERA
CAMERA SET UP
16:9•••••••••OFF
(
43)
To switch 16:9 on, open the menu and select [CAMERA SET UP]. Select
[16:9], set it to [ON] and close the menu.
”16:9” appears.
❍ The 16:9 mode is an electronically processed effect.
❍ The 16:9 mode cannot be selected in the Easy Recording mode.
❍ The multi-image screen cannot be used when the 16:9 format is selected.
❍ If you play back a 16:9 recording on a normal TV, the image appears vertically
“squashed” (compressed).
❍ If you connect the camcorder to a TV with an S1 terminal or Video ID-1
system, recordings made in the 16:9 mode will be automatically played back in
wide screen mode.
50
Demonstration Mode
The demonstration mode displays the camcorder’s main features. It starts
automatically when you leave the camcorder turned on without loading a cassette
and without inserting a memory card for more than 5 minutes. You can also start the
demonstration mode through the menu.
E
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
DISPLAY SET UP
DEMO MODE••••ON
(
43)
With no cassette and memory card inserted, open the menu and select
[DISPLAY SET UP]. Select [DEMO MODE], set it to [OFF] and close the
menu.
To cancel the demo mode, press any button, turn off the camcorder, load a cassette or
insert a memory card.
51
Changing the Recording Mode (SP/LP)
You can choose from SP (standard play) and LP (long play). LP extends the tape usage
by 1.5 times.
E
❍ Tapes recorded in LP mode cannot be used for audio dubbing (
insert ( 95).
97) or AV
❍ Depending on the nature and usage condition of the tape, picture and sound
recorded in LP mode may be distorted. We recommend using the SP mode for
important recordings.
❍ We recommend recording in SP mode if you plan to transfer the images to a
computer.
❍ If you record in both SP and LP modes on the same tape, the playback picture
may become distorted and the time code may not be written correctly.
❍ If you play back a tape that has been recorded in LP mode with another digital
device on this camcorder, or vice versa, picture and sound may become
distorted.
CARD CAMERA
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
VCR SET UP
REC MODE•••••SP
(
43)
To change to LP mode, open the menu and select [VCR SET UP]. Select
[REC MODE], set it to [LP] and close the menu.
52
Recording Still Images on the Tape
You can record still images on the tape. Starting your recording with a still image
allows you to easily locate the beginning of the recording with the Photo Search
E
function (
You can also record still images on a memory card while recording movies on a tape
110).
Open the menu and select [CAMERA SET UP]. Select [PHOTO REC], confirm that
86).
(
[TAPE }] is selected and close the menu.
PHOTO button
PHOTO button
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CAMERA
In Record Pause Mode
1. Press the PHOTO button halfway.
• F appears in green. If it does not appear in green, adjust the
focus with the focus ring.
• Exposure is locked.
• Focus can be adjusted manually with the focus ring when the
PHOTO button is pressed halfway.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
2. Press the PHOTO button fully.
• F disappears.
• The camcorder records the still image for approx. 6 seconds.
During this time, the camcorder displays the still image and
keeps recording the sound.
• The camcorder returns to record pause mode.
53
During Recording
1. Press the PHOTO button fully.
• The camcorder records the still image for approx. 6 seconds.
During this time, the camcorder displays the still image and
keeps recording the sound
E
• The camcorder returns to record pause mode.
❍ When you turn the POWER switch to OFF while the camcorder is recording the
still image, it will not turn off until recording is complete.
❍ Record still images under sufficient lighting condition (in which you can identify
the subject on the screen).
54
Using the Recording Programs
The camcorder is equipped with the Easy Recording program and several program AE
modes. The availability of functions differs depending on the selected mode.
E
Availability of Functions in Each Mode:
Position of the
Program Selector
[
Q
Position of the
TAPE/CARD switch
b /
b
1
1
*
*
Recording Program
[
h
Digital Zoom
Shutter Speed
Focus
h
×
h
h
A
A
h
h
h
A
h
h
h
h
h
h
A
White Balance
Exposure
Image Stabilizer*2
Digital Effects
16:9
ON
×
h
×
h
×
h*2
h*2
h
h
h
h
×
×
Card Mix
×
h
×
A: Auto setting h: Available ×: Not available
Shaded area: Can be used only when the TAPE/CARD switch is set to b.
*1: OPTURA20 only.
*2: Only Black and White can be used in CARD CAMERA mode.
Easy Recording Program
The camcorder adjusts focus, exposure and other settings
[
automatically, allowing you to just point and shoot.
Program AE Modes
Auto
The camcorder adjusts focus, exposure and other settings
automatically. However, you have the option of adjusting the
settings manually.
55
Sports
Use this mode to record sports scenes (such as tennis or golf),
moving objects (such as roller coasters) or when recording from a
moving car.
E
❍ This mode is set at a high shutter speed and should therefore be used in sufficient
light.
❍ This mode is mainly intended for frame-by-frame or slow playback. The picture may
not appear smooth when played back in normal speed.
Portrait
Use this mode to give accent to your subject by blurring the
background or foreground.
❍ The blur effect increases the more you zoom to telephoto.
❍ This mode is set at a higher shutter speed. The picture may not
appear smooth when played back.
Spotlight
Use this mode to record spotlit scenes such as shows, recitals or
fireworks.
Sand & Snow
Use this mode in bright places such as a sunny beach or ski resort. It
prevents the subject from being underexposed.
❍ The subject may become overexposed in dark surroundings. Check
the image on the screen.
❍ This mode is set at a higher shutter speed. The picture may not appear smooth when
played back.
Low Light
Use this mode to record in dimly lit places. The shutter is fixed at a
slow shutter speed.
❍ Moving subjects may leave a trailing afterimage.
❍ Picture quality may not be as good as in other modes.
❍ The camcorder may have difficulty to focus automatically.
56
Night
Use this mode to record in dark places. The shutter speed is
adjusted automatically. It is useful when recording in places with
changing light conditions (such as in amusement parks).
E
❍ Night mode cannot be used in CARD CAMERA mode.
❍ Moving subjects may leave a trailing afterimage.
❍ Picture quality may not be as good as in other modes.
❍ White points may appear on the screen.
❍ Autofocus may not work as well as in other modes. In such case, adjust the focus
manually.
Super Night (CAMERA mode)
In CAMERA mode, use this mode to record in very dark places. The
shutter speed is adjusted automatically. The White LED lights up
automatically illuminating the subject in the center of the screen,
allowing you to record brightly in color.
Low Light Plus (CARD CAMERA mode)
In CARD CAMERA mode, use this mode to record in dark places.
The shutter is fixed at a slow shutter speed. The White LED lights up
illuminating the subject in the center of the screen, allowing you to
record brightly in color.
❍ The range of the White LED is limited. Check the image on the screen when
recording.
❍ Use this mode for recordings at close range (up to 6.6 ft (2m)).
❍ Moving subjects may leave a trailing afterimage.
❍ Picture quality may not be as good as in other modes.
❍ White points may appear on the screen.
❍ Autofocus may not work as well as in other modes. In such case, adjust the focus
manually.
57
Selecting the Program AE Mode
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
E
1. Set the program selector to Q.
2. Press the selector dial.
A list of the program AE modes appears.
3. Select a mode and press the selector dial.
The symbol of the mode appears on the upper left corner of the
screen.
(Auto) disappears after 4 seconds.
❍ Do not change the mode during recording as the brightness of the image may
change abruptly.
❍ The setting resets to the Auto mode when you switch the program selector to
[.
❍ Bright light in a dark scene may cause a vertical light bar to appear. This is not
a malfunction.
58
Using Digital Effects
You can use the digital effects during recording and playback.
E
Faders (
Effects (
60): Begin or end scenes with a fade to or from black.
63): Add flavor to your recordings.
Multi-image screen (
65)
Availability of Digital Effects by Operating Modes:
CAMERA
PLAY (VCR)
CARD CAMERA CARD PLAY (VCR)
Movies Still Images
Faders
Effects
h
h
i
h
h
h
i
i
i
h*1
Multi-image
screen
h*2
h*2
h
i
i
h: Available i: Not available
*1: Black and White only.
*2: Cannot be used in Night and Super Night (OPTURA20) mode.
❍ Turn off the digital effect when you do not use it.
Press the DIGITAL EFFECTS button to open the menu. Select [D.EFFECTS |]
and press the ON/OFF button.
❍ The camcorder retains the setting even if you turn it off or change the program
AE mode.
❍ The digital effect turns off if you switch the program selector to [.
❍ Digital effects can be selected but not activated on a blank blue screen
(appears in PLAY (VCR) mode).
❍ Digital effects activated during playback do not change the recording.
❍ Digital effects cannot be used during DV dubbing and photo/date search.
❍ Digital effects can also be set with the wireless controller.
59
Faders
Fade Trigger (FADE-T)
The image gradually fades in.
E
The image gradually fades out.
Wipe (WIPE)
The image begins as a vertical
line in the center and
expands sideways until
it fills the whole screen.
The image is wiped off from the
sides of the screen.
Corner Wipe (CORNER)
The image appears from the
corners until it fills the
whole screen.
The image is wiped off from the
corners.
Jump (JUMP)
A small image appears from
the left, jumps into the
center and enlarges
until it fills the whole
screen.
The image shrinks, jumps from
the center to the left and
disappears.
Flip (FLIP)
The image flips into the screen.
The image flips out of the screen.
60
Puzzle (PUZZLE)
The image appears in 16 pieces.
The pieces move
around until the
E
puzzle is solved.
The image is divided into 16
pieces. The pieces move around
and disappear.
Zigzag (ZIGZAG)
The image appears in zigzag
from the top of the
screen.
Black stripes appear in zigzag
from the bottom of the screen
until they cover the whole image.
Beam (BEAM)
The screen turns yellow, forms
a beam that becomes
thinner and the image
appears.
A yellow beam appears in the
center of the screen and expands
until it covers the whole image.
Tide (TIDE)
The image appears from
both sides like tides.
The image disappears from both
sides like tides.
61
Selecting a Fader
CARD CAMERA
CARD PLAY (VCR)
CAMERA
PLAY (VCR)
E
1. In CAMERA mode, set the program selector to Q.
2. Press the DIGITAL EFFECTS button.
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.
3. Select [FADER].
4. Select the fader option.
5. Press the DIGITAL EFFECTS button.
The name of the selected fader flashes.
CAMERA mode:
6. Fade in: In record pause mode, press the ON/OFF
button and begin recording by pressing the
start/stop button.
Fade out: During recording, press the ON/OFF button
and pause recording by pressing the start/stop button.
The fader can be activated/deactivated by pressing the ON/OFF button.
PLAY (VCR) mode:
6. Fade in: In playback pause mode, press the ON/OFF
button and begin playback by pressing the e/a
button.
Fade out: During playback, press the ON/OFF button
and pause playback by pressing the e/a button.
The fader can be activated/deactivated by pressing the ON/OFF button.
Faders cannot be selected when Card Mix is activated.
62
Effects
Art (ART)
The image becomes like a paint (solarization).
E
Black and White (BLK & WHT)
The image becomes black and white.
Sepia (SEPIA)
The image becomes monochrome with a brownish tint.
Mosaic (MOSAIC)
The image is blurred through enlarging the size of some pixels.
Ball (BALL)
The image becomes like a ball.
Cube (CUBE)
The image becomes a cube and rotates.
Wave (WAVE)
Both ends of the image sway in waves.
Color Masking (COLOR M.)
The image becomes a rhombus surrounded by a masking frame that
changes the colors.
Mirror (MIRROR)
Creates a symmetrical image as if there would be a mirror in the
center of the screen.
Only Black and White can be used in CARD CAMERA mode.
63
Selecting an Effect
CARD CAMERA
CARD PLAY (VCR)
CAMERA
PLAY (VCR)
E
1. In CAMERA mode, set the program selector to Q.
2. Press the DIGITAL EFFECTS button.
[D.EFFECTS OFF], [FADER], [EFFECT] and [MULTI-S] appear.
3. Select [EFFECT].
4. Select the effect.
5. Press the DIGITAL EFFECTS button.
The name of the selected effect flashes.
6. Press the ON/OFF button.
• The name of the selected effect stops flashing.
• The effect can be activated/deactivated by pressing the ON/OFF
button.
Selecting an Effect in CARD CAMERA Mode
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
CARD CAMERA
1. Press the DIGITAL EFFECTS button.
“BLK&WHT” flashes.
2. Press the ON/OFF button.
• “BLK&WHT” stops flashing.
• The effect can be activated/deactivated by pressing the ON/OFF
button.
64
Using the Multi-Image Screen
The multi-image screen captures moving subjects in 4, 9 or 16 sequences of still images
with the Image Capture feature and displays them at one time. Sound will be
recorded normally. This feature can be used in CAMERA and PLAY (VCR) mode.
You can choose the transition speed at which to capture the subject from manual, fast
(every 4 frames), moderate (every 6 frames*) or slow (every 8 frames*).
E
* In Low Light mode: moderate (every 8 frames), slow (every 12 frames).
Selecting the Multi-Image Screen
CARD CAMERA
CARD PLAY (VCR)
CAMERA
PLAY (VCR)
1. In CAMERA mode, set the program selector to Q.
2. Press the DIGITAL EFFECTS button.
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.
3. Select [MULTI-S].
[S.SPEED] and [S.SPLIT] appears.
4. Select [S.SPEED].
[MANUAL], [FAST], [MOD.] and [SLOW] appear.
5. Select the transition speed.
6. Select [MULTI-S] again.
[S.SPEED] and [S.SPLIT] appears.
7. Select [S.SPLIT].
[4], [9], [16] settings appear.
8. Select the number of sequences.
9. Press the D.EFFECTS SELECT button.
[MULTI-S] flashes.
65
Capturing
10.Press the ON/OFF button.
• MANUAL: Images will be captured each time you press the ON/OFF button. The blue
frame indicating the next sequence disappears after the last image. To cancel the last
captured image, press and hold the ON/OFF button. To cancel the multi-image screen,
press and release the ON/OFF button.
E
• FAST, MODERATE, SLOW: The set number of images will be captured at the set speed.
To cancel the multi-image screen, press the ON/OFF button.
11.Press the start/stop button begin recording.
The multi-image screen is recorded on the tape.
❍ The multi-image screen can be operated in record or record pause mode.
❍ You can operate the multi-image screen only in the following playback modes:
-
When [S.SPEED] is set to [MANUAL]: Playback pause, slow forward/reverse
playback
-
When [S.SPEED] is set to [FAST], [MOD.] or [SLOW]: Playback pause
❍ The multi-image screen cannot be operated in Night and Super Night
(OPTURA20) mode.
❍ The multi-image screen cannot be selected when Card Mix is activated.
❍ In PLAY (VCR) mode: Pressing any tape operation button (such as play or
pause), or performing date/photo search cancels the multi-image screen.
66
Turning Off the Image Stabilizer
The image stabilizer allows you to obtain steady recordings even at telephoto. There is
no need to turn off the image stabilizer during normal recording. However, the
camcorder tries to compensate for horizontal movements and you may therefore
decide to turn it off during panning. The image stabilizer cannot be turned off when
the program selector is set to [.
E
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CAMERA
CAMERA SET UP
IMAGE S.
•••ON
(
43)
Open the menu and select [CAMERA SET UP]. Select [IMAGE S. i], set it
to [OFF] and close the menu.
i disappears.
❍ We recommend turning off the image stabilizer when you mount the
camcorder on a tripod.
❍ The image stabilizer is designed to compensate a normal degree of camcorder
shake.
❍ The image stabilizer cannot be used in CARD CAMERA mode.
❍ The image stabilizer cannot be used in Low Light mode.
❍ The image stabilizer might not be as effective when recording in dark places
using the Night or Super Night (OPTURA20) mode.
67
Recording With the Self-Timer
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
E
PHOTO
button
PHOTO button
Start/stop button
SELF T. button
Start/stop button
(self-timer)
button
1. Press the
(self-timer) button.
“
” appears.
When recording movies
2. Press the start/stop button.
The camcorder starts recording after a 10-second countdown (2
seconds when using the wireless controller). The count down
appears on the screen.
3. Press the start/stop button to stop recording.
The camcorder returns to record pause mode.
When recording still images
2. Press the PHOTO button.
• The camcorder starts recording after a 10-second countdown
(2 seconds when using the wireless controller). The count down
appears on the screen.
• F appears in green when recording begins.
•
The camcorder records the still image for approx. 6 seconds and returns to record pause
mode (in CARD CAMERA mode, it displays the still image when recording is complete).
❍ To cancel the self-timer, press the
(self-timer) button.
To cancel the self-timer once the countdown has begun, press the start/stop
button (when recording movies) or PHOTO button (when recording still
images).
❍ The self-timer will be canceled when you turn off the camcorder.
68
Audio Recording
Changing the Audio Mode
E
You can record sound in two audio modes—16-bit and 12-bit. The 12-bit mode records
sound on two channels (stereo 1), leaving 2 channels free (stereo 2) for adding new
sound later. Select the 16-bit mode for higher sound quality.
CARD CAMERA
CARD PLAY (VCR)
CAMERA
PLAY (VCR)
AUDIO SET UP
AUDIO MODE•••12bit
(
43)
Open the menu and select [AUDIO SET UP]. Select [AUDIO MODE], set it to
[16bit] and close the menu.
“16bit” appears for approximately 4 seconds.
For adding new sound, see Audio Dubbing (
97).
Recording with an External Microphone
You can use an external microphone for
recording. Almost all stereo microphones with
a plug diameter of 0.14 inch (3.5 mm) can be
connected to the MIC terminal. Use a
microphone with a built-in power supply
(condenser microphone).
❍ The audio level differs from that of the built-in microphone.
❍ Be careful with long microphones as they may appear in the picture.
❍ See also Using the DM-50 Microphone (
75).
Wind Screen
You can reduce the wind noise when recording in windy places.
CARD PLAY (VCR)
CAMERA
PLAY (VCR)
CARD CAMERA
AUDIO SET UP
WIND SCREEN••OFF
(
43)
Open the menu and select [AUDIO SET UP]. Select [WIND SCREEN], set it
to [ON] and close the menu.
“WS ON” appears when you turn the wind screen on.
69
❍ Low sound may be reduced together with the wind noise. We recommend
turning off the wind screen for normal recordings.
❍ The wind screen function cannot be turned on/off during recording.
❍ The wind screen function can also be used for audio dubbing (when [AUDIO
DUB.] is set to [MIC. IN] in the [AUDIO SET UP] submenu).
E
❍ The wind screen function cannot be used when an external microphone is
connected to the MIC terminal or when the DM-50 Microphone is attached to
the advanced accessory shoe.
Using Headphones during Recording
You can use headphones to monitor the sound during recording.
When using headphones, make sure that “H” is displayed. If “H” is not displayed
change the setting following the procedure below.
Switching the AV/Headphones Terminal
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
VCR SET UP
AV/PHONES••••AV
(
43)
Open the menu and select [VCR SET UP]. Select [AV/PHONES], set it to [AV]
or [PHONES H ] and close the menu.
Adjusting the Headphone Volume
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
AUDIO SET UP
HVOLUME•••••
(
43)
Open the menu and select [AUDIO SET UP]. Select [ H VOLUME], adjust
the volume with the selector dial and close the menu.
You can turn off the volume completely by turning the selector dial down until [OFF]
appears. Turn the selector dial up to increase the volume again.
70
Using the VL-3 Video Light (Optional)
This video light enables you to record brightly in color even in dark places. This VL-3
E
Video Light attaches to the camcorder’s
advanced accessory shoe for cable-free
operation and is powered by the camcorder’s power supply.
Refer also to the VL-3 Video Light instruction manual.
❍ Always turn off the camcorder before attaching/removing the video light.
❍ Do not touch or place flammable material or plastic close to the lamp or the
surrounding parts during or immediately after use; they become very hot.
❍ Do not look directly at the lamp while the video light is on.
❍ Do not carry the camcorder by the video light.
1. Remove the accessory shoe cover.
q
2. Slide the video light into the
accessory shoe until it clicks.
3. Tighten the shoe lock.
K
C
LO
w
Be careful that the video light does not come
off when tightening the shoe lock.
4. Set the camcorder to CAMERA or
CARD CAMERA mode.
r
5. Set the video light’s power switch to
AUTO or ON.
e
•
(Connection) appears.
• ON: The video light stays on.
• AUTO: The video light turns on and off
automatically.
K
C
LO
t
O
T
N
U
O
A
F
F
O
L
O
C
K
71
Using the VFL-1 Video Flash Light (Optional)
The VFL-1 Video Flash Light allows you to record still images and movies even at night
E
or in dark places. This video flash light attaches to the camcorder’s
advanced
accessory shoe for cable-free operation and is powered by the camcorder’s power
supply.
Using it as video light, you can set it to turn on and off automatically according to the
surrounding brightness. Using it as flash, you can set it to fire automatically according
to the brightness of the subject and the settings of the camcorder, or to fire a pre-
flash to reduce the red-eye effect.
Refer also to the VFL-1 Video Flash Light instruction manual.
❍ Always turn off the camcorder before attaching/removing the video flash light.
❍ Do not carry the camcorder by the video flash light.
Attaching the Video Flash Light
1. Remove the accessory shoe cover.
q
2. Slide the video flash light into the
accessory shoe until it clicks.
3. Tighten the shoe lock.
w
Be careful that the video flash light does not
come off when tightening the shoe lock.
r
e
t
72
Using the Video Flash Light as Flash
Selecting the Flash Mode
E
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
CAMERA SET UP
FLASH••••••AUTO
(
43)
1. Set the camcorder to CAMERA or CARD CAMERA mode.
2. Set the video flash light’s POWER switch to ON.
3. Open the menu and select [CAMERA SET UP]. Select [FLASH], select a
setting option and close the menu.
• AUTO : The flash fires automatically according to the brightness of the subject.
• RED-EYE : The flash fires automatically according to the brightness of the subject,
and fires a pre-flash for red-eye reduction.
• FLASH ON : The flash always fires.
• FLASH OFF : The flash does not fire. Use this setting in places where flash
photography is prohibited.
• The symbol of the selected flash mode appears on the screen. “ ” disappears after
4 seconds.
Recording a Still Image with Flash
1. Press the PHOTO button halfway.
F appears in green.
2. Press the PHOTO button fully.
The flash fires and the still image shown on the screen will be recorded.
❍ Do not fire the flash close to people’s eyes.
❍ Do not fire the flash at persons while they are driving.
❍ Do not fire the flash with the flash bulb covered with your hand.
❍ The practical range of the flash is approx. 3.3 to 18 ft. (1 to 5.5 m). The range
depends upon the recording condition.
❍ The camcorder fires a pre-flash to obtain the subject’s exposure data and
adjusts the main flash to the optimal intensity (flash exposure compensation).
When [RED-EYE ] is set, the pre-flash fires between the flash for red-eye
reduction and the main firing (the main firing takes place about 1 second after
the flash for red-eye reduction).
❍ The effect of flash photography may not be obtained in bright places.
❍ For the red-eye reduction mode to be effective, the subject needs to look at
the flash. The degree of reduction depends upon the distance and on each
individual.
73
❍ The red-eye reduction mode cannot be used in stitch assist mode.
❍ The flash cannot be used in Night and Super Night (OPTURA20) mode.
❍ The flash will not fire in the following cases:
-
-
When you press the EXP button in [AUTO ] or [RED-EYE ] mode.
When a shutter speed of 1/2000 or faster is set in CAMERA mode (the flash
mark appears in purple). However, if [FLASH ON ] is selected, the display
of the selected shutter speed flashes in purple for 4 seconds and the shutter
speed becomes set to 1/1000; the flash fires.
E
-
-
When an abnormality occurs during charging (the flash mark flashes in red).
When the multi-image screen is selected or when you are recording movies
onto a tape (no flash mark appears).
-
When the flash mark does not appear in green when you press the PHOTO
button. Set it to [FLASH ON ] if necessary.
❍ When the flash is fired with an accessory such as an optional tele-converter
attached to the camcorder, its shadow may be recorded.
❍ An image recorded with flash may flicker when played back on a different
device.
Using the Video Flash Light as Video Light
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
1. Set the camcorder to CAMERA or CARD CAMERA mode.
2. Set the video flash light’s POWER switch to AUTO or ON.
(Connection) appears.
•
• ON: The video light stays on.
• AUTO: The video light turns on and off automatically.
❍ Do not touch or place flammable material or plastic close to the lamp or the
surrounding parts during or immediately after use; they become very hot.
❍ Do not look directly at the lamp while the video light is on.
74
Using the DM-50 Microphone (Optional)
The high sensitive Directional Stereo Microphone DM-50 attaches to the
advanced accessory shoe for cable-free operation and is powered by the camcorder’s
power supply. Use it for recording or dubbing audio.
E
Refer also to the DM-50 Microphone instruction manual.
❍ Always turn the camcorder off before attaching/removing the microphone.
❍ Do not connect any microphone to the MIC terminal when the DM-50
Microphone is connected.
❍ Do not carry the camcorder by the microphone.
1. Remove the accessory shoe cover.
2. Slide the microphone into the
q
accessory shoe until it clicks.
3. Tighten the shoe lock.
w
Be careful that the microphone does not
come off when tightening the shoe lock.
4. Set the camcorder to CAMERA or
CARD CAMERA mode.
r
(Connection) appears.
5. Set the microphone’s directivity
switch.
• SHOTGUN: For recording clear sound from
the front (monaural).
• STEREO 1: For recording sound from the
front and surrounding area.
• STEREO 2: For recording surrounding
sound in a wider range than in
STEREO 1.
t
e
75
Adjusting the Focus Manually
Autofocus may not work well on the following subjects:
E
Subjects with
Reflective surfaces
low contrast
(e.g. White Wall)
Fast Moving Subjects Horizontal Stripes
Through dirty or
wet windows
Different Distances
Dark Subjects
Night Scenes
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
1. Set the program selector to Q.
2. Adjust the zoom.
When you operate the zoom after adjusting the focus, the
subject may not stay in focus. Adjust the zoom before the focus.
3. Press the FOCUS button.
“MF” appears.
4. Turn the focus ring to adjust the focus.
• Turn the focus ring up or down until the image appears
focused.
5. Press the FOCUS button to return to autofocus.
The setting resets to autofocus when you switch the program selector to [.
76
Infinity Focus
Use this function when you wish to focus on faraway subjects such as mountains or
fireworks.
E
Press the focus button more than 3 seconds in step 3.
“MF ∞” appears. When you operate the zoom or turn the focus ring, “∞” disappears and
the camcorder changes to manual focus.
AF-Assist Lamp (Optional VFL-1 Attached)
When you attach the VFL-1 Video Flash Light to the camcorder and set it to fire a flash
(
73), the AF-assist lamp (White LED) illuminates the subject in the center of the
screen to enable the camcorder to focus in dark places.
*
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
CARD CAMERA
*[FOCUS PRI.] set to [ON]
When you press the PHOTO button halfway, the AF-assist lamp turns on
automatically responding to the surrounding brightness.
*
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
*[FOCUS PRI.] set to [OFF]
When you press the PHOTO button halfway and turn the focus ring, the
AF-assist lamp turns on responding to the surrounding brightness.
❍ The camcorder may not be able to focus even though the AF-assist lamp is
lighting. In such case, adjust the focus manually.
❍ The AF-assist lamp lights up brightly. Consider turning off the AF-assist lamp in
public places such as in restaurants or theaters.
❍ Turn off the AF-assist lamp in places where flash photography is prohibited.
Turning Off the AF-Assist Lamp
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
CAMERA SET UP
AF AST LAMP••AUTO
(
43)
To turn off the AF-assist lamp, open the menu and select [CAMERA SET
UP]. Select [AF AST LAMP], set it to [OFF] and close the menu.
77
Adjusting Exposure Manually
Exposure Lock
You can lock the exposure when recording in situations where the lighting may
E
change suddenly to control the brightness of the image.
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
1. Set the program selector to Q.
2. Press the EXP button.
• “E.LOCK 0” appears on the screen.
• When you operate the zoom, the brightness of the image may
change.
Exposure Adjustment
When the exposure is locked, you can adjust it manually to handle difficult lighting
conditions. The camcorder’s iris can be set to any position from fully closed to fully
open.
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
Turn the selector dial to adjust the brightness of the
image.
• To make the image brighter, turn the selector dial up (to a
maximum of +11).
• To make the image darker, turn the selector dial down (to a minimum of –11).
Press the EXP button to return to auto exposure.
78
Setting the Shutter Speed
In the
(Auto) mode, you can adjust the shutter speed manually to make stable
E
shots of fast moving subjects.
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
CAMERA SET UP
SHUTTER••••••AUTO
(
43)
1. Set the program selector to Q.
2. Set the program AE mode to the [
AUTO] mode.
3. Open the menu and select [CAMERA SET UP].
4. Select [SHUTTER].
5. Select the shutter speed and press the selector dial.
CAMERA Mode
CARD CAMERA Mode
AUTO
1/60
AUTO
1/60
1/100
1/250
1/500
1/1000
1/2000
1/4000
1/8000
1/100
1/250
6. Close the menu.
❍ Do not point the camcorder directly at the sun when the shutter speed is set to
1/1000 or higher.
❍ The image may flicker when recording with high shutter speeds.
❍ The setting resets to the auto setting when you switch the program selector to
[, or change the program AE mode.
❍ If the shutter speed is set to 1/500 or higher in CAMERA mode and you switch
to CARD CAMERA mode, it automatically changes to 1/250.
❍ Recording under fluorescent lights: When the camcorder is set to [ (Easy
Recording) or when the program AE mode is set to Auto, Night or Super Night
(OPTURA20) mode, it automatically detects the flicker of fluorescent lighting
and adjusts the shutter speed accordingly. However, if the brightness of the
screen starts to flicker, select Auto mode and set the shutter speed to 1/100.
79
❍ Guidelines for Recording with High Shutter Speeds:
-
-
-
Outdoor sports such as golf or tennis: 1/8000, 1/4000,
1/2000
E
Moving objects such as cars or roller coasters: 1/1000,
1/500 or 1/250
Indoor sports such as basketball: 1/100
80
Setting the White Balance
The camcorder’s auto white balance system adjusts the colors to appear natural for
different lighting conditions. However, you can use the preset modes to reproduce
colors more accurately, or set a custom white balance to obtain the optimal setting.
E
Zoom lever
Program selector
White sheet
or paper
Selector dial
MENU button
❍ When the program selector is set to [, white balance is preset to [AUTO].
Indoor, outdoor and custom white balance cannot be selected.
❍ The camcorder retains the setting even if you turn it off.
❍ When you have set the custom white balance:
-
-
Reset the white balance when the lighting condition changes.
Turn off the digital zoom.
❍ Setting the white balance manually may provide better results in the following
cases:
-
-
-
-
Changing lighting conditions
Close-ups
Subjects in a single color (sky, sea or forest)
Under mercury lamps or certain types of fluorescent lights
❍ Use the T Indoor or U Outdoor mode in the following cases:
T Indoor:
-
-
-
Changing lighting condition
Under video light
Under sodium lamps
U Outdoor:
-
-
For night scenes or fireworks
Sunrise or sunset
* Use the auto setting for normal outdoor scenes.
81
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
CAMERA SET UP
WHITE BAL.•••AUTO
E
(
43)
For T (Indoor) or U (Outdoor) Setting:
1. Set the program selector to Q.
2. Open the menu and select [CAMERA SET UP].
3. Select [WHITE BAL.].
4. Select [INDOOR T] or [OUTDOOR U].
“T” or “U” appears.
5. Close the menu.
For Custom White Balance:
1. Set the program selector to Q.
2. Open the menu and select [CAMERA SET UP].
3. Select [WHITE BAL.].
4. Point the camcorder at a white object (such as a sheet of paper), zoom
in until it fills the whole screen and select [SET W].
• W flashes and stops flashing when settings is complete.
• Depending on the light source, W may keep flashing. The result will still be better
than with the auto setting.
5. Close the menu.
82
Magnifying the Image
The playback image can be magnified up to 5 times.
E
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY (VCR)
1. Move the zoom lever toward T.
• The image is magnified by 2 times.
• To further enlarge the image, move the zoom lever toward T.
To shrink the image below 2 times magnification, move the
zoom lever toward W.
• A frame appears indicating the position of the enlarged part.
2. Move the image.
• Turn the selector dial to move the image to the right and left,
or up and down. Pressing the selector dial switches between
the directions.
• To cancel the magnification, move the zoom lever toward W until the frame
disappears.
Movies played back from a memory card cannot be magnified.
83
Displaying the Data Code
Once date and time are set, the camcorder maintains a data code containing
recording date and time and other camera data such as shutter speed and exposure
(f-stop). Only date and time appear when playing back a memory card.
E
MENU button
Select
buttons
MENU button
DATA CODE
button
DATA CODE
button
Selector dial
❍ The data code display turns off when you turn the camcorder off.
❍ The data code may not be displayed if a recording made with this camcorder is
played back on a different digital camcorder.
❍ The data code cannot be displayed in frame advance/reverse playback. Camera
data may not appear in some special playback modes.
❍ When the TV screen displays are hidden (
140), the displays still appear on
the LCD screen. If you turn on the data code, displays other than the data
code will disappear from the LCD screen.
Available Data Code Combinations (in PLAY (VCR) mode):
DATA CODE
Date/Time &
Camera data
(tape only)
Date/Time
Camera data
D/TIME SEL.
F1.8
Date
Time
F1.8
1/250
JAN. 1,2003
1/250
JAN. 1,2003
F1.8
F1.8
1/250
1/250
12:00:00 PM
12:00:00 PM
F1.8
1/250
12:00 PM
JAN. 1,2003
12:00 PM
JAN. 1,2003
Date & Time
F1.8
1/250
84
Selecting the Date/Time Display Combination
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY (VCR)
E
DISPLAY SET UP
D/TIME SEL.••DATE & TIME
(
43)
Open the menu and select [DISPLAY SET UP]. Select [D/TIME SEL.], set it to
[DATE] or [TIME] and close the menu.
Selecting the Data Code Display Combination
CAMERA
CARD CAMERA
CARD PLAY (VCR)
PLAY (VCR)
DISPLAY SET UP
DATA CODE••••DATE/TIME
(
43)
Open the menu and select [DISPLAY SET UP]. Select [DATA CODE], set it to
[CAMERA DATA] or [CAM. & D/T] and close the menu.
Displaying the Data Code
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY (VCR)
Press the DATA CODE button.
Only date and time appear in CARD PLAY (VCR) mode.
Six-Second Auto Date
Date and time appear for 6 seconds when you begin playback, or to indicate that date
or time zone has changed.
CAMERA
CARD CAMERA
CARD PLAY (VCR)
PLAY (VCR)
DISPLAY SET UP
6SEC.DATE••••OFF
(
43)
Open the menu and select [DISPLAY SET UP]. Select [6SEC.DATE], set it to
[ON] and close the menu.
85
Photo Search/Date Search
You can search for a still image recorded
anywhere on the tape with the photo search
function, or locate the change of the
E
SEARCH SELECT button
Search buttons
date/time zone with the date search function.
STOP 3 button
CAMERA
CARD CAMERA
CARD PLAY (VCR)
PLAY (VCR)
1. Press the SEARCH SELECT button to choose between
photo search and date search.
INDEX SLIDE SHOW
CARD
DATA CODE SEARCH SELECT
ZERO SET
REW
PLAY
STOP
FF
MEMORY
“PHOTO SEARCH” or “DATE SEARCH” appears.
12bit
AUDIO OUT
2. Press the + or - button to begin searching.
INDEX SLIDE SHOW
CARD
DATA CODE SEARCH SELECT
ZERO SET
• Press the + button to search forward and the - button to
search backward.
REW
PLAY
STOP
FF
MEMORY
12bit
AUDIO OUT
• Press more than once to search for further still images or date
changes (up to 10 times).
• Press the + or - button to change the search direction.
• Press the 3 (stop) button stop searching.
❍ Photo search: A still image recorded very close to the point you start the search
may not be detected.
❍ Date search: A recording of longer than a minute per date/area is required.
❍ Date search: Playback may start slightly before or after the date change.
❍ Date search may not function if the data code is not correctly displayed.
86
Returning to a Pre-marked Position
If you wish to return to a particular scene
later, mark the point with the zero set
E
REW ` button
memory and the tape will stop at that point
when you rewind/fast forward the tape.
PLAY e button
FF 1 button
ZERO SET
MEMORY
button
STOP 3 button
CARD CAMERA
CARD PLAY (VCR)
CAMERA
PLAY (VCR)
1. Press the ZERO SET MEMORY button at the point
you wish to return to later.
INDEX SLIDE SHOW
CARD
DATA CODE SEARCH SELECT
ZERO SET
REW
PLAY
STOP
FF
MEMORY
• “0:00:00 ” appears.
12bit
AUDIO OUT
• To cancel, press the ZERO SET MEMORY button again.
2. When you have finished playback, fast forward or
rewind the tape.
• “RTN 1” or “` RTN” appears.
• The tape stops automatically at “0:00:00”.
• The tape counter changes to time code.
❍ Time code and tape counter display may not match accurately.
❍ The zero set memory may not function correctly when blank sections exist on
the tape.
❍ If you remove the tape, the zero set memory is canceled and the counter
display shows the time code.
87
Recording to a VCR or Digital Video Device
You can copy your recordings by connecting the camcorder to a VCR or a digital video
device. If you connect a digital video device, you can copy recordings with virtually no
generation loss in image and sound quality.
E
When connecting a VCR:
❍ Make sure that “H” is not displayed on the screen. If “H” is displayed, change
the setting (
70).
❍ The quality of the edited tape will be slightly lower than that of the original.
When connecting a digital video device:
❍ You can connect only one device to the camcorder with the DV cable.
❍ Blank sections may be recorded as anomalous picture.
❍ If the picture does not appear, reconnect the DV cable or turn the camcorder
off and back on again.
Example: Recording to a VCR
CAMERA
CARD CAMERA
CARD CAMERA
PLAY (VCR)
1. Connect the camcorder to the VCR.
See Playing Back on a TV Screen ( 40).
2. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
3. Connected device: Load a blank cassette and set the device to record
pause mode.
4. Locate the scene you wish to copy and pause playback shortly before
the scene.
5. Play back the tape.
6. Connected device: Begin recording when the scene you wish to copy
appears. Stop recording when copying is complete.
7. Stop playback.
88
Connecting a Digital Video Device
Refer also to the instruction manual of the digital video device.
E
Side with an arrow
Signal flow
Commercially available DV cable
89
Recording from Analog Video
Devices (VCR, TV or Camcorder)
E
You can record videos or TV programs from a VCR or analog camcorder on the tape in
the camcorder.
❍ Anomalous signals sent from the connected device may be recorded as
anomalous picture (although it may not appear so on the screen), or it may not
be recorded at all.
❍ You cannot record from tapes with copyright protective signals.
❍ Headphones cannot be used during analog line-in recording. If the
AV/headphones terminal set to [PHONES H], it will automatically switch to [AV].
CAMERA
CARD CAMERA
CARD CAMERA
PLAY (VCR)
1. Connect the camcorder to the analog video device.
See Playing Back on a TV Screen ( 40).
2. Set the camcorder to PLAY (VCR) mode and load a blank cassette.
3. Connected device: Load the recorded cassette.
4. Press the REC PAUSE button.
In record pause mode and during recording, you can check the
picture on the screen.
5. Connected device: Play back the tape.
6. Press the e/a button when the scene you wish to
record appears.
7. Press the 3 button to stop recording.
• Press the e/a button to pause recording.
• Press the e/a button again to restart recording.
8. Connected device: Stop playback.
90
Recording from Digital Video
Devices (DV Dubbing)
E
You can record from other digital video devices equipped with a DV terminal with
virtually no loss in picture and sound quality.
❍ When recording from digital video devices, make sure that “AV \ DV” is not
displayed on the screen. If “AV \ DV” is displayed, change the setting
(
94).
❍ Anomalous signals sent from the connected device may be recorded as
anomalous picture (although it may not appear so on the screen), or it may not
be recorded at all.
❍ Copyright protected signals cannot be recorded.
❍ Blank sections may be recorded as anomalous picture.
❍ If the picture does not appear, reconnect the DV cable or turn the camcorder
off and back on again.
❍ You can connect only one device with the DV cable.
❍ You can use the camcorder for playback and recording without reconnecting
the DV cable.
CAMERA
CARD CAMERA
CARD CAMERA
PLAY (VCR)
1. Connect the camcorder to the digital video device.
See Connecting a Digital Video Device ( 89).
2. Set the camcorder to PLAY (VCR) mode and load a blank cassette.
“DV IN” appears.
3. Connected device: Load the recorded cassette.
4. Press the REC PAUSE button.
In record pause mode and during recording, you can check the
picture on the screen.
5. Connected Device: Play back the tape.
6. Press the e/a button when the scene you wish to
record appears.
7. Press the 3 button to stop recording.
• Press the e/a button to pause recording.
• Press the e/a button again to restart recording.
8. Connected Device: Stop playback.
91
Copyright Signal
Certain software tapes are copyright protected. If you attempt to play back such tape,
“COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED” appears and you will not be able
to view the contents of the tape. If you attempt to record from such tape via the DV
terminal, “COPYRIGHT PROTECTED DUBBING RESTRICTED” appears and you will not
be able to record the contents of the tape.
E
92
Converting Analog Signals into Digital
Signals (Analog-Digital Converter)
E
By connecting the camcorder to a VCR or 8mm video camcorder, you can convert
analog video/audio signals to digital signals and output the digital signals via the DV
terminal. The DV terminal serves as output terminal only.
❍ Headphones cannot be used during analog-digital conversion.
❍ Unload the tape from the camcorder.
❍ Turn off all devices before starting the connections.
❍ Depending on the signal sent from the connected device, the conversion from
analog to digital signals might not work properly (e.g., signals that include
copyright protective signals or anomalous signals such as ghost signals).
We recommend powering the camcorder from a household power source.
Connecting the Devices
This illustration shows how to connect using a S-video cable. You can also connect the
yellow plug of the stereo video cable to the VIDEO terminal. Refer also to the
instruction manual of the connected device.
OUTPUT
Signal flow
S(S1)-VIDEO
S-150 S-video Cable
(optional)
VIDEO
L
Signal flow
AUDIO
R
STV-250N Stereo Video
Cable (supplied)
DV
Signal flow
Commercially available DV cable
93
Turning On the Analog-Digital Converter
CAMERA
CARD CAMERA
CARD CAMERA
PLAY (VCR)
E
Press the AV \ DV button on the wireless controller.
OR
VCR SET UP
AV DV OUT••••OFF
(
43)
Open the menu and select [VCR SET UP]. Select [AV\DV OUT], set it to
[ON] and close the menu.
❍ For normal use, set [AV\DV OUT] to [OFF] (so that “AV\DV” does not
appear on the screen). If it is set to [ON], digital signals cannot be input via the
camcorder’s DV terminal.
❍ Depending on the software and the specifications of your computer, you may
not be able to transfer converted signals via the DV terminal.
94
Replacing Existing Scenes (AV Insert)
You can insert and replace images/audio on the tape of the camcorder with
images/audio from other video devices connected via AV terminal or DV terminal.
E
Scene to be inserted
Playback tape
Insert start
Insert end
Tape in the
camcorder
before inserting
Tape in the
camcorder after
inserting
Inserted scene
❍ You cannot insert from a TV program when the synchronized signals are
distorted.
Camcorder:
❍ Use only tapes recorded in SP mode.
❍ AV insert will stop if the camcorder detects a blank section or a section not
recorded in SP mode on the tape.
Connected device:
❍ Use only tapes without blank sections.
❍ AV insert may not work correctly if the tape has a blank section or changes in
the recording mode.
❍ AV insert cannot be performed when the quality of the recording is poor, or
during special playback such as fast forward, rewind, playback pause, slow
playback etc.
95
Example: AV Insert from a VCR
CAMERA
CARD CAMERA
CARD CAMERA
PLAY (VCR)
E
1. Connect the camcorder to the VCR.
See Playing Back on a TV Screen ( 40).
2. VCR: Load a recorded cassette. Locate the scene you wish to insert and
pause playback shortly before the scene.
3. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
Make sure the tape-protect switch is set to allow recording.
4. Locate the scene you wish to replace and pause playback shortly before
the scene.
You can use the playback buttons on the camcorder or the special playback buttons on
the wireless controller.
12bit
STOP
5. Press the AV INSERT button on the wireless
controller.
AUDIO OUT
AUDIO DUB. PAUSE
SLOW
2
AV INSERT AV DV REMOTE SET
REC
“AV INSERT” and “2a” appear.
PAUSE
6. VCR: Play back the tape.
7. Press the PAUSE a button on the wireless controller
when the scene you wish to insert appears.
ZERO SET
MEMORY
REW
PLAY
STOP
SLOW
FF
12bit
AUDIO OUT
AUDIO DUB. PAUSE
2
AV INSERT AV DV REMOTE SET
8. Press the STOP 3 button on the wireless controller
ZERO SET
MEMORY
REW
PLAY
STOP
SLOW
FF
12bit
AUDIO OUT
to stop inserting.
AUDIO DUB. PAUSE
2
Press the PAUSE a button on the wireless controller to pause
AV INSERT AV DV REMOTE SET
inserting.
9. VCR: Stop playback.
Set the zero set memory at the end of the scene you wish to replace. The
camcorder will automatically stop AV insert at that point.
96
Audio Dubbing
You can add sound from audio devices (AUDIO IN) or with the built-in or an external
microphone (MIC. IN).
E
❍ Use only tapes recorded in SP mode 12-bit audio sound with this camcorder.
Audio dubbing will stop if the tape has a blank section or a section recorded in
LP mode, 16-bit or 12-bit 4-channel sound. In above case, create a copy in SP
mode 12-bit audio sound using the analog line-in function.
❍ Do not connect/disconnect any cable to/from the camcorder while dubbing.
❍ You cannot use the DV terminal for audio dubbing.
❍ If you add sound to a tape not recorded with this camcorder, sound quality
may decrease.
❍ Sound quality may decrease when you add sound to the same scene for more
than 3 times.
Connecting an Audio Device
AV
Signal flow
L
STV-250N Stereo Video Cable
(supplied)
R
You can monitor the picture on the LCD screen or a TV connected via the
S-video terminal, and check the sound with the built-in speaker.
97
Using a Microphone
E
MIC
❍ When using the built-in microphone: Do not connect any cables to the
microphone terminal or the accessory shoe.
❍ When using an external microphone: Connect it to the microphone terminal.
❍ When using the DM-50 Microphone: Do not connect any cables to the
microphone terminal.
❍ When you connect a TV via the S-video terminal, you can check the picture on
the TV screen and the sound with headphones connected to the camcorder.
When you connect a TV via the AV terminal, you can check the picture on the
TV screen but you cannot check the sound with headphones.
Dubbing
CAMERA
CARD CAMERA
CARD CAMERA
PLAY (VCR)
AUDIO SET UP
AUDIO DUB.•••AUDIO IN
(
43)
1. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
2. Open the menu and select [AUDIO SET UP]. Select [AUDIO DUB.], set it
to [AUDIO IN] or [MIC. IN] and close the menu.
3. Locate the scene you wish audio dubbing to start.
4. Press the PAUSE a button on the wireless controller.
5. Press the AUDIO DUB. button on the wireless
12bit
STOP
SLOW
AUDIO OUT
AUDIO DUB. PAUSE
2
controller.
AV INSERT AV DV REMOTE SET
• “AUDIO DUB.” and “ a” appear.
• If the optional DM-50 microphone is attached,
(Connection) appears.
REC
PAUSE
6. Press the PAUSE a button on the wireless controller
to begin dubbing.
ZERO SET
MEMORY
REW
PLAY
STOP
SLOW
FF
12bit
AUDIO OUT
AUDIO DUB. PAUSE
2
• Audio device: Begin playback.
AV INSERT AV DV REMOTE SET
• Microphone: Direct your voice to the microphone.
98
7. Press the STOP 3 button on the wireless controller
to stop dubbing.
ZERO SET
MEMORY
REW
PLAY
STOP
SLOW
FF
12bit
AUDIO OUT
AUDIO DUB. PAUSE
2
Audio device: Stop playback.
AV INSERT AV DV REMOTE SET
E
Set the zero set memory at the end of the scene you wish to dub audio. The
camcorder will automatically stop audio dubbing at that point.
Playing Back the Added Sound
You can select to play back Stereo 1 (original sound), Stereo 2 (added sound), or adjust
the balance of both sounds.
MENU button
12bit AUDIO
OUT button
Selector dial
CAMERA
CARD CAMERA
CARD CAMERA
PLAY (VCR)
AUDIO SET UP
12bit AUDIO•••STEREO1
(
43)
1. Open the menu and select [AUDIO SET UP]. Select [12bit AUDIO OUT],
select a setting and close the menu.
• STEREO1: Plays back the original sound.
• STEREO2: Plays back the added sound.
• MIX/FIXED: Plays back stereo 1 and stereo 2 in the same level.
• MIX/VARI.: Plays back stereo 1 and stereo 2. The mix balance can be adjusted.
2. If you have selected [MIX/VARI.], adjust the mix level: Open the menu
and select [AUDIO SET UP]. Select [MIX BALANCE], adjust the balance
with the selector dial and close the menu.
Turn the selector dial down to increase the volume of Stereo 1 and up to increase the
volume of Stereo 2.
❍ The camcorder resets to [STEREO1] when you turn the camcorder off. However,
the mix balance is memorized by the camcorder.
❍ You can also press the 12bit AUDIO OUT button on the wireless controller to
select the audio output. However, the mix balance can only be adjusted in the
menu.
99
Connecting to a Computer Using a DV (IEEE1394) Cable
You can transfer recordings to a computer equipped with a DV (IEEE1394) terminal or
IEEE1394 capture board (optional software required).
E
DV IN/OUT
terminal
DV
IEEE1394 (DV)
terminal
Commercially available DV cable
❍ Do not disconnect the DV cable, or turn off the camcorder or computer while
data is being transferred to the computer.
❍ Operation may not work correctly depending on the software and the
specifications/settings of your computer.
❍ We recommend powering the camcorder from a household power source
while it is connected to the computer.
❍ Refer also to the instruction manual of the computer.
❍ Optional software required. Refer also to the instruction manual of the
software.
❍ For transferring recordings from a memory card to the computer using a USB
cable, see p. 135.
DV NETWORK SOLUTION DISK (Windows XP Users)
Windows XP users can use the software on the supplied DV NETWORK SOLUTION
DISK to perform videoconference and file transfer over the Internet, or upload files
from the computer to the memory card and use the camcorder as card reader/writer.
The available functions depend upon the camcorder model and the networking
environment. For details, refer to the DV NETWORK SOLUTION DISK Software
Instruction Manual.
❍ Do not disconnect the DV cable, remove the memory card or turn off the
camcorder or computer while data is being transferred to the computer (while
the camcorder’s card access indicator is flashing). Doing so may damage the
memory card’s data.
❍ The image files on your memory card and the image files saved on the hard
disk drive of your computer are your valuable, original data files. If you wish to
use image files on your computer, be sure to make copies of them first,
retaining the original.
100
Inserting and Removing the Memory Card
You can use
SD Memory Cards or a
Terminals
E
commercially available MultiMediaCards with
this camcorder. The SD Memory Card has a
protect switch for prevent accidental erasure.
❍ This camcorder is compatible with SD Memory Cards or MultiMediaCards only.
Do not use any other types of memory cards.
❍ Turn off the camcorder before inserting or removing the memory card.
Otherwise, it may result in data damage.
❍ Do not touch the memory card terminals.
❍ If you use memory cards other than the supplied one, make sure to format
them with the camcorder (
❍ For instructions on how to connect the camcorder to the computer, see
Connecting to a Computer Using a USB Cable ( 135).
134).
Inserting the Card
1. Turn off the camcorder.
2. Open the cover.
3. Insert the memory card all the way
into the memory card slot.
4. Close the cover.
Do not close the cover forcefully without
having the card correctly inserted.
Removing the Card
Do not forcefully remove the memory card without first pushing it in.
1. Turn off the camcorder.
Make sure that the card access indicator is not
flashing before you turn off the camcorder.
2. Open the cover.
3. Push the memory card to release it.
Remove the memory card.
4. Close the cover.
Card access indicator
101
Selecting the Image Quality/Size
Changing the Still Image Quality
You can choose between Superfine, Fine and Normal.
E
CAMERA
CARD PLAY (VCR)
PLAY (VCR)
CARD CAMERA
CARD SET UP
SI QUALITY•••FINE
(
43)
Open the menu and select [CARD SET UP]. Select [SI QUALITY], set it to
[SUPER FINE] or [NORMAL] and close the menu.
Changing the Still Image Size
You can choose between 1280 × 960 pixels and 640 × 480 pixels.
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
CARD CAMERA
CARD SET UP
SI SIZE••••••1280×960
(
43)
Open the menu and select [CARD SET UP]. Select [SI SIZE], set it to
[640×480] and close the menu.
❍ Still images recorded in 1280 × 960 pixels may not be displayed correctly in a
camcorder not supporting this size.
❍ Still images are compressed and recorded in the JPEG (Joint Photographic
Experts Group) format.
❍ Depending on subject and recording condition, changing the image quality
may not show a significant difference.
❍ Estimated Capacity of a 8 MB Memory Card and File Size per Image:
640 × 480
1280 × 960
Image Size
Image Quality
File Size
File Size
No. of Images
No. of Images
per Image
850 KB
550 KB
300 KB
per Image
175 KB
120 KB
65 KB
Superfine
Fine
6 images
10 images
18 images
34 images
50 images
84 images
Normal
These figures are approximate. They vary according to the recording condition
and the subject. Sample images already recorded on the supplied SD Memory
Card are to be included in the total number.
❍ Remaining Image Capacity:
flashing in red: No card
in green: 6 or more images
in yellow: 1 to 5 images
in red: No more images
102
❍ The indication may not decrease even though a recording has been made, or
may decrease by 2 images at once.
❍ All indicators are displayed in green when a memory card is played back.
❍ The remaining image capacity indicates the number of still images, even when
movies are recorded.
E
Changing the Movie Size
You can choose between 320 × 240 pixels and 160 × 120 pixels.
CAMERA
CARD PLAY (VCR)
PLAY (VCR)
CARD CAMERA
CARD SET UP
MOVIE SIZE•••320×240
(
43)
Open the menu and select [CARD SET UP]. Select [MOVIE SIZE], set it to
[160×120] and close the menu.
❍ Movies are recorded in the Motion JPEG format.
❍ Maximum continuous recording time:
Max. Continuous
Recording Time
Image Size
Total File Size
File Size per Second
320 × 240
160 × 120
10 sec.
30 sec.
2.7 MB
2.7 MB
270 KB/sec.
90 KB/sec.
File Numbers
Images are automatically assigned file numbers from 0101 to 9900 and stored in
folders containing up to 100 images. Folders are assigned numbers from 101 to 998.
(The sample images on the supplied memory card are saved in the [100canon] folder.)
You can choose to use consecutive file numbers (CONTINUOUS) or to reset the file
number each time a different memory card is inserted (RESET). We recommend setting
the file numbers to CONTINUOUS.
CONTINUOUS
The camcorder memorizes the file number of the last image and assigns the
consecutive file number to the next image, even when a new memory card is inserted.
(If a higher file number already exists on the memory card, the consecutive number
will be assigned.) There will be no duplication of file numbers. This is useful for
organizing images on a computer.
RESET
The file number will be reset each time a new memory card is inserted, starting with
101-0101. If the memory card already contains image files, the consecutive file number
will be assigned.
103
When you record 3 images on the supplied memory card.
101-0101
101
E
101-0102
CONTINUOUS
RESET
101-0103
When you replace the memory
card and record an image.
101-0104
101-0101
101
101
CAMERA
CARD PLAY (VCR)
PLAY (VCR)
CARD CAMERA
CARD SET UP
FILE NOS.••••CONTINUOUS
(
43)
To change the setting, open the menu and select [CARD SET UP]. Select
[FILE NOS.], set it to [RESET] and close the menu.
104
Recording Still Images on a Memory Card
You can record still images with the
PHOTO button
E
Card access
indicator
camcorder, from a tape in the camcorder
108) or from devices connected via the
DV terminal or AV terminal ( 109).
(
❍ Do not turn off the camcorder, disconnect the power source or remove the
memory card while the card access display (<<< or >>>) in the upper right
corner of the screen or the card access indicator is flashing. Doing so could
result in data damage.
❍ When you are using a SD Memory Card, make sure that the protect switch is
set to allow recording.
Make sure to insert a memory card with enough remaining capacity.
Recording with the Camcorder
In autofocus mode, the camcorder keeps focusing automatically. Furthermore, this
camcorder is equipped with the Focus-Priority mode for even more accurate focus. In
Focus-Priority mode, you can choose between three focusing points (
However, you can turn off the Focus-Priority mode if you wish to put timing ahead of
focusing ( 107).
106).
When the program selector is set to [, the Focus-Priority mode is set to ON (only the
center focusing point available).
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
CARD CAMERA
1. Set the camcorder to CARD CAMERA mode.
A white focusing frame appears in the center of the screen. The camcorder will focus on
the subject in the center of the screen. To change the focusing point, see Selecting a
Focusing Point (
106).
2. Press the PHOTO button halfway.
• F and focusing frame turn green when focus is adjusted. The
beep sounds twice. The picture may appear out of focus for a
moment while the camcorder is focusing.
• Exposure is locked.
•
Focus can be adjusted manually with the focus ring when the PHOTO button is pressed
halfway.
•
When you press the PHOTO button on the wireless controller, recording starts immediately.
105
3. Press the PHOTO button fully.
• F disappears and you hear a shutter sound.
• The card access indicator flashes and the card access display
appears.
E
• The still image shown on the screen will be recorded on the memory card.
❍ To use the self-timer (
68), press the
(self-timer) button before step 2
and press the PHOTO button fully.
❍ If the subject is not suitable for autofocus, the focusing frame turns yellow and
locks the focus. The confirmation sound beeps once. Adjust the focus manually
with the focus ring.
❍
The focusing frame gives an indication of the focusing point. Depending on the
size of the subject or the distance, the camcorder may focus outside the frame.
❍ When the subject is too bright (overexposed), “OVEREXP” starts flashing. If
you have turned off the built-in ND filter, we recommend changing the setting
back to AUTO. Open the menu and select [CAMERA SET UP]. Select [ND
FILTER], set it to [AUTO] and close the menu.
❍ “OVEREXP” does not appear when you press the EXP button.
Selecting the Focusing Point
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
CARD CAMERA
FINE
50
1. Set the camcorder to CARD CAMERA mode.
A white focusing frame appears in the center of the screen.
2. Set the program selector to Q.
FINE
50
3. Turn the selector dial to display all focusing frames.
Three focusing frames appear on the screen, one of it in green.
4. Turn the selector dial to select the focusing point.
FINE
50
Turn the selector dial up to select the frame to the right, down
to select the frame to the left.
5. Record the still image.
❍ If you operate the zoom lever, press the EXP button or do not press the PHOTO
button within 4 seconds, the frames other than the selected one disappear.
106
❍ The focusing point can be selected only when Focus-Priority is set to [ON] in
CARD CAMERA mode. The focusing point returns to the center if you turn off
the camcorder, change from CARD CAMERA mode or move the program
selector to [.
E
❍ The focusing point cannot be selected in Stitch Assist mode.
❍ The focusing point cannot be selected when using the digital zoom. When you
zoom into the digital zoom range, the focusing frame flashes for 4 seconds
and disappears. When you return to the optical zoom range, the focusing
frame reappears.
❍ The focusing point cannot be selected when focusing manually.
❍ The focusing point cannot be selected when recording movies on a memory
card.
Turning Off the Focus-Priority Mode
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
CARD CAMERA
CAMERA SET UP
FOCUS PRI.•••ON
(
43)
Open the menu and select [CAMERA SET UP]. Select [FOCUS PRI.], set it to
[OFF] and close the menu.
Continuous Shooting
You can capture a quick series of still images with the continuous shooting function.
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
CARD CAMERA
CAMERA SET UP
DRIVE MODE•••SINGLE
(
43)
1. Set the camcorder to CARD CAMERA mode.
2. Open the menu and select [CAMERA SET UP]. Select [DRIVE MODE], set
it to [CONT. ] and close the menu.
3. Press and hold the PHOTO button to record the still images.
A series of still images will be recorded.
4. Release the PHOTO button to end recording.
107
❍ The setting resets to [SINGLE] when you turn the camcorder off.
❍ Maximum number of continuous shots at one time (at 16 MB or more
available capacity):
E
Optional VFL-1
Attached
Frames per
Second
Maximum Number
of Continuous Shots
Still Image Size
1280 × 960
640 × 480
Flash ON/OFF
Flash OFF
2 frames
3 frames
2 frames
10 images
30 images
10 images
Flash ON
*These figures are approximate and vary with the recording conditions and subjects.
❍ If you attach the optional VFL-1 Video Flash Light, the practical range of the
flash in the Continuous Shooting mode is approx. 3.3 ft. (1 m) to 6.6 ft. (2 m).
Auto Exposure Bracketing
With Auto Exposure Bracketing (AEB), the camcorder records a still image in three
different exposures (dark, normal, light), allowing you to choose the perfect exposed shot.
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
CARD CAMERA
CAMERA SET UP
DRIVE MODE•••SINGLE
(
43)
1. Set the camcorder to CARD CAMERA mode.
2. Open the menu and select [CAMERA SET UP]. Select [DRIVE MODE], set
it to [AEB ] and close the menu.
3. Press the PHOTO button.
Three still images in different exposures are recorded to the memory card.
The setting resets to [SINGLE] when you turn the camcorder off.
Recording from a Tape in the Camcorder
You can record images from a tape in the camcorder as still images on a memory card.
CAMERA
CARD CAMERA
CARD PLAY (VCR)
PLAY (VCR)
1. Set the camcorder to PLAY (VCR) mode.
2. Play back the tape.
3. Press the PHOTO button halfway when the scene you wish to record
appears.
• The camcorder pauses playback. The remaining image capacity and other information
appear.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
108
4. Press the PHOTO button fully.
• The card access indicator flashes.
• The still image shown on the screen will be recorded on the memory card.
• You can also record a still image by pressing the PHOTO button fully when the tape is
in playback pause mode.
E
❍ A still image recorded from an image in 16:9 format will be vertically
compressed.
❍ The data code of the still image will reflect the date and time it has been
recorded on the memory card.
❍ There will be no shutter sound in PLAY (VCR) mode.
❍ The size of the still image will be 640 × 480.
Recording from Other Video Devices
You can record images from devices connected via the S-video terminal or AV terminal
(analog line-in function), or via the DV terminal as still images on a memory card.
When recording via the AV terminal, make sure that “AV\DV” is displayed on
the screen. When recording via the DV terminal, make sure that “AV\DV” is not
displayed. Change the setting as necessary (
94).
CAMERA CARD CAMERA
CARD PLAY (VCR)
PLAY (VCR)
1. Connect the camcorder to the video device.
• S-video/AV terminal: See Playing Back on a TV Screen (
• DV terminal: See Connecting a Digital Video Device (
2. Set the camcorder to PLAY (VCR) mode.
40).
89).
If a cassette is loaded, make sure the tape is stopped.
3. Connected device: Load a recorded cassette and play back the tape.
4. Press the PHOTO button halfway when the scene you wish to record
appears.
• The still image, remaining image capacity and other information appear.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
5. Press the PHOTO button fully.
• The card access indicator flashes.
• The still image shown on the screen will be recorded on the memory card.
❍ A still image recorded from an image in 16:9 format will be vertically
compressed.
❍ The data code of the still image will reflect the date and time it has been
recorded on the memory card.
❍ There will be no shutter sound in PLAY (VCR) mode.
❍ The size of the still image will be 640 × 480.
109
Recording Still Images on a Memory Card While Recording
Movies on a Tape
You can record still images on a memory card by pressing the PHOTO button while
you are recording a movie on the tape.
E
❍ The size of the still image will be 640 × 480.
❍ You can use the full zoom range (16× optical zoom and 64×/320× digital
zoom).
❍ The quality of the still image is slightly lower than a still image recorded in
CARD CAMERA mode.
❍ Card mix cannot be used when [PHOTO REC] is set to [CARD ].
❍ The still image cannot be recorded on a memory card when a fader, effect or
the multi-image screen is activated.
❍ The beep does not sound when you press the PHOTO button while recording a
movie on the tape.
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CAMERA
CAMERA SET UP
PHOTO REC••••TAPEb
(
43)
1. Set the camcorder to CAMERA mode.
2. Open the menu and select [CAMERA SET UP]. Select [PHOTO REC], set it
to [CARD ] and close the menu.
3. While you are recording a movie, press the PHOTO button.
The image shown on the screen will be recorded on the memory card.
110
Recording Panoramic Images (Stitch Assist Mode)
You can shoot a series of overlapping images and merge them into one large
panoramic scene using the supplied software (PhotoStitch) on a computer.
E
When Recording in Stitch Assist Mode:
PhotoStitch detects the overlapping portion of adjoining images and merges them. Try
to include a distinctive item (landmark, etc.) in the overlapping portion.
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
CARD CAMERA
1. Set the camcorder to CARD CAMERA mode.
2. Press the button.
3. Select the direction with the CARD +/– button.
CARD + button: clockwise. CARD – button: counterclockwise.
4. Select the program AE mode and zoom on the subject.
Adjust focus and exposure manually as necessary. Once the sequence has started, you
cannot change the program AE mode, exposure, zoom or focus.
5. Press the PHOTO button to record the first image.
Direction and number of recorded images appear.
6. Record the second image so that it overlaps a portion of the first image.
• Minor discrepancies in the overlapped area can be corrected with the software.
• You can retake an image by pressing the CARD +/– button to return to the previous
image.
• A maximum of 26 images can be recorded.
7. Press the
button after the last image.
For details on how to merge these images, refer to the DIGITAL
VIDEO SOLUTION DISK Software Instruction Manual.
111
❍ Compose each image so that it overlaps 30 to 50% of the adjoining image. Try
to keep the vertical misalignment within 10%.
❍ Do not include moving subject in the overlapping portion.
❍ Do not try to stitch images that include both distant and close subjects. They
may appear warped or doubled up.
E
❍ The continuous shooting mode cannot be used in Stitch Assist mode.
112
Recording Motion JPEG Movies on a Memory Card
You can record Motion JPEG movies with the camcorder, from a tape in the camcorder
E
(
114), or from devices connected via the AV terminal (analog line-in) or the DV
terminal ( 114).
❍ Do not turn off the camcorder, disconnect the power source or remove the
memory card while the card access display (<<< or >>>) in the upper right
corner of the screen or the card access indicator is flashing. Doing so could
result in data damage.
❍ When you are using a SD Memory Card, make sure that the protect switch is
set to allow recording.
❍ Do not load/unload a cassette during recording.
❍ Make sure to insert a memory card with enough remaining capacity.
❍ The sound of a movie recorded on a memory card will be monaural.
Recording with the Camcorder
CAMERA
PLAY (VCR)
CARD PLAY (VCR)
CARD CAMERA
1. Set the camcorder to CARD CAMERA mode.
2. Press the start/stop button to begin recording.
You can record up to 10 seconds in 320 × 240 and up to 30
seconds in 160 × 120.
3. Press the start/stop button to stop recording.
The camcorder starts writing the movie on the memory card.
To use the self-timer (
68), press the
(self-timer) button before step 2 and
press the start/stop button.
113
Recording from a Tape in the Camcorder
You can record movies from a tape in the camcorder on a memory card.
CAMERA
CARD CAMERA
CARD PLAY (VCR)
PLAY (VCR)
E
1. Set the camcorder to PLAY (VCR) mode.
2. Play back the tape.
3. Press the start/stop button when the scene you wish to record appears.
You can record up to 10 seconds in 320 × 240 and up to 30 seconds in 160 × 120.
4. Press the start/stop to stop recording.
❍ A movie recorded from an image in 16:9 format will be vertically compressed.
❍ The data code of the movie will reflect the date and time it has been recorded
on the memory card.
Recording from Other Video Devices
You can record movies from devices connected via the S-video terminal or AV terminal
(analog line-in function), or via the DV terminal on a memory card.
CAMERA
CARD CAMERA
CARD PLAY (VCR)
PLAY (VCR)
1. Connect the camcorder to the video device.
• S-video/AV terminal: See Playing Back on a TV Screen (
• DV terminal: See Connecting a Digital Video Device (
2. Set the camcorder to PLAY (VCR) mode.
40).
89).
If a cassette is loaded, make sure the tape is stopped.
3. Connected device: Load a recorded cassette and play back the tape.
4. Press the start/stop button when the scene you wish to record appears.
You can record up to 10 seconds in 320 × 240 and up to 30 seconds in 160 × 120.
5. Press the start/stop button to stop recording.
❍ A movie recorded from an image in 16:9 format will be vertically compressed.
❍ The data code of the movie will reflect the date and time it has been recorded
on the memory card.
114
Playing Back a Memory Card
You can play back memory card images on the LCD screen, viewfinder screen, or on a
E
connected TV screen (see Playing Back on a TV Screen
40).
You can display a single image (single image display), 6 at one time (index screen
116), or one after another (slide show 116). Use the Card Jump function to quickly
locate an image without displaying them one by one ( 117).
❍ Images not recorded with this camcorder, uploaded from a computer (except
the sample images 138), edited on a computer and images whose file
names have been changed may not be played back correctly.
❍ Do not turn off the camcorder, disconnect the power source or remove the
memory card while the card access display (<<<) in the upper right of corner of
the screen or the card access indicator is flashing. Doing so could result in data
damage.
❍ Make sure to insert a memory card that contains images.
❍ Only date and time will be displayed when pressing the DATA CODE button.
❍ You can enlarge still images up to 5 times during playback (
83).
Single Image Display
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Set the camcorder to CARD PLAY (VCR) mode.
• The last recorded image appears.
• Movies are displayed with the first scene as a still image indicated by “e/a”.
2. Press the CARD +/– button to move between images.
Press the CARD + button to display the next image and the
CARD – button to display the previous image.
3. To play back a movie, press the e/a button.
The last scene appears as a still image when playback is
complete.
115
Index Screen
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
1. In single image display, press the INDEX SCREEN
button.
• Up to 6 images appear.
• Movies are displayed with the first scene as a still image
indicated by “ ”.
2. Press the CARD +/– button to change the image
selection.
3. Move the
mark to the image you wish to view.
• Turn the selector dial up to move to the next image and down
to move to the previous image.
• Turning the selector dial up on the last image displays the next
index screen. Turning the selector dial down on the first image
displays the previous index screen.
4. Press the INDEX SCREEN button.
The index screen is canceled and the selected image appears in
single image display.
Slide Show
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. In single image display, press the SLIDE SHOW
button.
Images are played back one after another.
2. Press the SLIDE SHOW button to stop the slide show.
116
Card Jump Function
You can locate still images/movies without displaying them one by one. The number in
the upper right of the screen indicates the image number of the current image by the
total number of images.
E
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
In single image display, press and hold the CARD + or
CARD – button.
• Press the CARD + button to jump forward and the CARD – button
to jump backward.
• When you release the button, the still image/movie of the
displayed image number appears.
117
Protecting Images
You can protect important images from accidental erasure during single image display
or index screen display.
E
If a memory card is formatted, all images, even protected ones, will be erased
permanently.
❍ The sample images recorded on the supplied SD Memory Card are already
protected.
❍ Movies can only be protected when the first or last scene is displayed as a still
image. They cannot be protected during playback pause.
❍ Make sure to insert a memory card that contains images.
Protecting during Single Image Display
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Select the image you wish to protect.
2. Press the selector dial to open the FILE OPERATION menu.
3. Select [PROTECT ].
• “ ” appears and now the image cannot be erased.
• To cancel the protection, press the selector dial.
4. Select [b RETURN] to close the menu.
Protecting during Index Screen Display
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CARD OPERATIONS
PROTECT
(
43)
1. In single image display, press the INDEX SCREEN button.
Up to 6 images appear.
2. Open the menu and select [CARD OPERATIONS].
3. Select [\ PROTECT
4. Select the image you wish to protect and press the selector dial.
• “ ” appears on the image.
].
• Repeat this step to protect more images.
• To cancel the protection, press the selector dial.
5. Press the MENU button.
To cancel the protection, press the selector dial in step 4. “
the image can now be erased.
” disappears and
118
Erasing Images
You can erase images singly or all at once.
E
Be careful when erasing images. Erased images cannot be recovered.
❍ Protected images cannot be erased.
❍ Movies can only be erased when the first or last scene is displayed as a still
image. They cannot be erased in playback pause mode.
❍ Make sure to insert a memory card that contains images.
Erasing a Single Image
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Select the image you wish to erase.
2. Press the selector dial to open the FILE OPERATION menu.
3. Select [IMAGE ERASE].
• “ERASE THIS IMAGE?”, [NO] and [YES] appears.
• If an image is protected, [YES] appears in purple.
4. Select [YES].
The image is erased and the previous image appears.
5. Select [b RETURN] to close the menu.
Erasing a Single Image/All Images
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CARD OPERATIONS
IMAGE ERASE
(
43)
1. Open the menu and select [CARD OPERATIONS].
2. Select [IMAGE ERASE].
3. Select [SINGLE] or [ALL].
• When erasing a single image: “ERASE THIS IMAGE?” [NO] and [YES] appears. If an
image is protected, [YES] appears in purple.
• When erasing all images: “ERASE ALL IMAGES? [EXCEPT FOR
and [YES] appears.
IMAGES]”, [NO]
4. Select [YES] and close the menu.
• When erasing a single image: The image is erased and the previous image appears. To
erase another image, select the image with the CARD +/– button and select [YES].
• When erasing all images: All images with exception of the protected images are erased.
119
Selecting Still Images for Printing (Print Order)
You can select still images for printing and set the number of copies. These print order
settings are compatible with the Digital Print Order Format (DPOF) standards.
E
❍ Make sure to insert a memory card that contains images.
❍ A maximum of 200 still images can be selected.
❍ Movies cannot be printed.
Selecting in Single Image Display
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. Select the still image you wish to print.
2. Press the selector dial to open the FILE OPERATION menu.
3. Select [ PRINT ORDER].
4. Select the number of copies.
• “ ” appears on the image.
• To cancel the print order, set the number of copies to 0.
5. Select [b RETURN] to close the menu.
Selecting in Index Screen Display
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CARD OPERATIONS
PRINT ORDER
(
43)
1. In single image display, press the INDEX SCREEN button.
Up to 6 images appear.
2. Open the menu and select [CARD OPERATIONS].
3. Select [\ PRINT ORDER].
4. Select the still image you wish to print and press the selector dial.
5. Set the number of copies with the selector dial and close the menu.
• “ ” appears on the image.
• To cancel the print order, set the number of copies to 0.
• Repeat steps 4 and 5 to continue the print order setting.
120
Erasing All Print Orders
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
E
CARD OPERATIONS
PRINT ORDERS ALL ERASE
(
43)
1. In single image display, open the menu and select [CARD OPERATIONS].
2. Select [
“ERASE ALL
PRINT ORDERS ALL ERASE].
PRINT ORDERS?”, [NO] and [YES] appears.
3. Select [YES].
All “ ” disappear.
4. Select [b RETURN] to close the menu.
121
Printing with the Direct Print Function
You can print still images by connecting the camcorder to a printer with Direct Print
function. The Direct Print function can also be used with the print order settings
E
(
120).
❍ Observe the following precautions during printing, otherwise printing may not
be performed correctly.
-
-
-
-
Do not turn off the camcorder or the printer.
Do not change the position of the TAPE/CARD switch.
Do not detach the cable.
Do not remove the memory card.
❍ Still images not recorded with this camcorder may not be printed correctly on a
printer with direct print function.
❍ The direct print function is supported by Canon Card Photo Printers with the
logo and Canon Bubble Jet Printers with the
logo.
❍ Refer to the instruction manual of each printer for information on which
interface cable to use with the camcorder.
The Card Photo Printers CP-10 and CP-100 are supplied with two direct
interface cables. Use the cable with the USB logo on the connector (DIF-100).
❍ We recommend powering the camcorder from a household power source.
❍ Refer also to the instruction manual of the respective printer.
❍ The screenshots in this section are examples taken from a printer with direct
print function. Options for the [Style] category will differ slightly depending on
the printer.
Connecting the Printer to the Camcorder
Printer with
direct print function
1. Turn off the camcorder and insert a memory card that contains still images.
2. Connect a power source to the printer and turn on the printer.
122
3. Set the camcorder to CARD PLAY (VCR) mode.
Wait until the card access indicator stops flashing.
4. Connect the camcorder to the printer using the cable.
E
Print
SET
”
” appears when the printer is properly connected to the camcorder. (Does
not appear with movies, or still images that cannot be played back with the camcorder.)
Printing
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
1. In single image display, select the still image you
wish to print and press the selector dial.
The print setting menu appears.
2. Set the number of copies, the print style and the
trimming settings.
• Selecting the Number of Copies.
• Setting the Print Style (
124).
126).
• Trimming Settings (
3. Select [Print] and press the selector dial.
Printing starts. The print setting menu disappears when printing
is complete.
If an error message appears, see Printing Errors (
Messages ( 146).
127) and Direct Print Related
Selecting the Number of Copies
A maximum of 9 copies can be selected for one still image.
1. In the print setting menu, turn the selector dial so
that appears next to [Copies] and press the
selector dial.
2. Turn the selector dial to select the number of copies and press the
selector dial.
123
Setting the Print Style
Card Photo Printer:
Image
Standard
Multiple
Prints 1 still image per page.
E
Prints 8 copies of the same still image on one page.
Borders Borderless Prints right to the edges of the page.
Bordered Prints with a border.
• [Multiple] can only be selected when printing on card size paper.
• [Borders] can only be selected when [Image] is set to [Standard].
Bubble Jet Printer:
Paper Size
Card #1*, Card #2*, Card #3*, LTR, A4
For details on paper type, refer to the Bubble Jet Printer User
Guide.
Borders Borderless Prints right to the edges of the page.
Bordered Prints with a border.
* Recommended paper size
Card Photo Printer: Selecting the Image Style
1. In the print setting menu, turn the selector dial to
select [Style] and press the selector dial.
2. Make sure that
dial.
is selected and press the selector
3. Turn the selector dial to select the image style and press the selector
dial.
4. Press the MENU button.
You return to the print setting menu.
124
Bubble Jet Printer: Selecting the Paper Size
1. In the print setting menu, turn the selector dial to
select [Style] and press the selector dial.
E
2. Make sure that is selected and press the selector
dial.
3. Turn the selector dial to select the paper size and press the selector dial.
4. Press the MENU button.
You return to the print setting menu.
Selecting the Borders
1. In the print setting menu, turn the selector dial to
select [Style] and press the selector dial.
2. Turn the selector dial to select
selector dial.
and press the
3. Turn the selector dial to select a borders option and press the selector
dial.
4. Press the MENU button.
You return to the print setting menu.
❍ Bordered: The image area remains relatively unchanged from the recorded
image when it is printed.
❍ Borderless/Multiple: The center portion of the recorded image is printed at an
enlarged size. The image’s top, bottom and sides may be cropped slightly.
❍ Card Photo Printer: A still image set to [Multiple] will be printed without
borders.
125
Trimming Settings
Set the print style before you start with the trimming settings.
E
1. In the print setting menu, select [Trimming] and press
the selector dial.
The trimming frame appears.
2. Change the size of the trimming frame.
MENU
W
T
• Move the zoom lever toward T to shrink the frame, and toward
W to enlarge the frame.
• To cancel the trimming settings, move the zoom lever toward W until the trimming
frame disappears.
3. Move the trimming frame.
• Turn the selector dial to move the image to the right and left, or up and down.
Pressing the selector dial switches between the directions.
4. Press the MENU button.
You return to the print setting menu.
❍ About the color of the trimming frame:
-
-
-
White: No trimming settings.
Green: Recommended trimming size.
Red: The image is magnified beyond recommended size. The image may
print out coarsely.
❍ The trimming frame may not appear depending on the image size, paper size
or borders settings.
❍ The trimming setting applies only to one image.
❍ The trimming setting is canceled with the following operations:
-
-
-
When you turn off the camcorder.
When you disconnect the interface cable.
When you expand the trimming frame beyond its maximum size.
126
Printing with Print Order Settings
You can print still images you have selected with the Print Order function. If you wish
to print more than 1 copy, set the number of copies in the print order (
120).
E
When printing with print order settings, you can select the print style such as
bordered or borderless, but not the trimming settings.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
PRINT
(
43)
1. Connect the printer to the camcorder (
2. Press the MENU button.
122).
3. Select [\
• The print setting menu appears.
• “Set print order” appears, when you connect a printer with direct print function and
select [\ PRINT] without having set the print order.
The total number of prints set in the print order is displayed on the upper left of the screen.
PRINT].
•
4. Set the print style.
Setting the Print Style (
124).
5. In the print setting menu, select [OK] and press the selector dial.
Printing starts. The print setting menu disappears when printing is complete.
❍ Cancel Printing
Press the selector dial while “Now Printing” is displayed. A confirmation dialog
appears. Select [OK] and press the selector dial. Printing stops even if it is
incomplete and the paper is fed through.
❍ Restarting Printing (with
print order only)
Open the CARD PLAY (VCR) menu and select [\
PRINT]. Select [Restart] in
the print setting menu and press the selector dial. The remaining images will
be printed.
Printing cannot be restarted in the following cases:
-
-
When you change the print order settings.
When you delete a still image with print order settings.
❍ Printing Errors
-
-
If an error occurs during the printing process, an error message appears
146).
(
Bubble Jet Printer: With most errors, printing resumes automatically after
you correct the error. If the error persists, press the selector dial to cancel
printing. Refer also to the Bubble Jet Printer Quick Start Guide for details.
Card Photo Printer: Turn the selector dial to select [Stop] or [Restart] and
press the selector dial. (The [Restart] setting may not appear with some error
messages. In that case, select [Stop].)
-
❍ Follow below procedure when disconnecting the interface cable:
1. Disconnect the cable from the camcorder and printer.
2. Turn off the camcorder.
127
Combining Images (Card Mix)
You can produce effects not possible with just a tape with the Card Mix function.
Choose one of the sample images provided on the supplied SD Memory Card (such as
picture frames, backgrounds and animations) and combine it with the live video
recording.
E
❍ Card mix cannot be used when [PHOTO REC] is set to [CARD ].
❍ Movies recorded on a memory card cannot be combined with camcorder
recordings.
❍ Make sure to load a cassette and to insert a memory card that contains card
mix images.
❍ Additional sample images are provided on the supplied DIGITAL VIDEO
SOLUTION DISK. For instructions on how to upload them to the memory card,
refer to Adding Still Images from Your Computer to the Memory Card in the
DIGITAL VIDEO SOLUTION DISK Software Instruction Manual.
❍ Reselect the card mix image when you have turned off the camcorder, changed
the position of the program selector or removed the memory card.
Card Mix Effects
You can select from the following 4 types of Card Mix effects:
Card Chroma Key (CARD CHROMA)
Combines frames with your recordings. The live video recording will appear in place of
the blue area of the card mix image. If you create your own frame, make sure that the
area the live recording should appear is blue.
Mix level adjustment: blue area of the still image.
Live video recording
Card mix image
128
Card Luminance Key (CARD LUMI.)
Combines illustrations or title with your recordings. The live video recording will
appear in place of the light area of the card mix image. You can create your own title
or illustration by drawing on a white paper and recording it to the memory card.
Mix level adjustment: light area of the still image.
E
Live video recording
Card mix image
Camera Chroma Key (CAM. CHROMA)
Combines backgrounds with your recordings. Record your subject in front of a blue
curtain, and the subject not blue will be superimposed on the card mix image.
Mix level adjustment: blue area of the live video recording.
Live video recording
Card mix image
Card Animation (C. ANIMATION)
Combines animations with your recordings. You can choose from 3 types of card
animation effects.
Corner: Animation appears on the upper left and the lower right corner of the screen.
Straight: Animation appears on the top and bottom of the screen and moves to the
right and left.
Random: Animation moves randomly in the display.
Mix level adjustment: blue area of the card animation image.
Live video recording
Card mix image
129
Selecting the Card Mix Effect
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CAMERA
E
CARD MIX
MIX TYPE•••••CARD CHROMA
–
+
MIX LEVEL••••
(
43)
1. Set the program selector to Q.
2. Open the menu and select [\CARD MIX].
The card mix menu appears.
3. Select the image you wish to combine with the
CARD +/– button.
4. Select [MIX TYPE].
[CARD CHROMA], [CARD LUMI.], [CAM. CHROMA] and [C. ANIMATION] appears.
5. Select the mix type matching the image you have selected (
138).
• The screen shows the combined image.
• When you have selected [C. ANIMATION], select [ANIMAT. TYPE] and select between
[CORNER], [STRAIGHT] and [RANDOM].
6. To adjust the mix level, select [MIX LEVEL] and adjust it with the
selector dial.
7. Close the menu.
“CARD MIX” flashes.
Activating the Card Mix Effect
1. Press the CARD MIX button.
• “CARD MIX” stops flashing.
• The combined image appears.
• You can activate and deactivate the card mix effect by pressing
the CARD MIX button.
130
Recording with the Card Mix Effect
Movie:
1. Press the start/stop button to begin recording.
The combined image is recorded on the tape.
E
2. Press the start/stop button to end recording.
Still Image:
1. Press the PHOTO button halfway.
F flashes in white and turns green when focus is adjusted.
2. Press the PHOTO button fully.
• The camcorder records the still image on the tape for approx.
6 seconds. During this time, the camcorder displays the still
image and keeps recording the sound.
• The camcorder returns to record pause mode.
131
Copying Still Images
You can copy still images from tape to memory card, or from memory card to tape.
E
❍ All still images from the selected still image onward will be copied.
❍ The size of a still image copied from tape to memory card will be 640 × 480.
❍ The data code of the still image reflects the date and time it has been copied.
Copying Still Images from Tape to Memory Card
Insert a memory card with enough remaining capacity, and load a recorded cassette.
CAMERA
CARD CAMERA
CARD PLAY (VCR)
PLAY (VCR)
[
COPY
]
CARD OPERATIONS
(
43)
1. Locate the still image you wish to copy on the tape and stop the tape
shortly before the still image.
• You can also use the photo search function to easily locate the
still image.
• To copy all still images from the tape, rewind the tape to the
beginning.
2. Open the menu and select [CARD OPERATIONS].
3. Select [COPY [b \
] ].
[CANCEL] and [EXECUTE] appears.
4. Select [EXECUTE].
• “NOW COPYING” appears.
• The still image being copied is shown on the screen.
• Copying stops when the tape reaches the end or the memory card is full (“CARD
FULL” appears).
5. Press the 3 (stop) button to end copying.
132
Copying Still Images from Memory Card to Tape
Load a cassette with enough free space, and insert a recorded memory card. Make
sure that the protect tab on the cassette is set to allow recording.
E
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
[
COPY
]
CARD OPERATIONS
(
43)
1. Select the first still image you wish to copy with the
CARD +/– buttons.
To copy all still images from the memory card, select the first still
image.
2. Open the menu and select [CARD OPERATIONS].
3. Select [COPY [
\ b] ].
[CANCEL] and [EXECUTE] appears.
4. Select [EXECUTE].
• “NOW COPYING” appears.
• It takes about 6 seconds per still image to be copied to the tape.
• Copying stops when all still images are copied or the tape is full.
5. Press the 3 (stop) button to end copying.
133
Formatting a Memory Card
Format new memory cards, or when you get the message “CARD ERROR”. You can
also format a memory card to erase all images recorded on it.
The camcorder formats memory cards in the Design rule for Camera File system (DCF)
standard.
E
❍ Formatting a memory card erases all data, including protected images.
❍ Images erased by formatting cannot be recovered.
❍ If you use a memory card other than the supplied one, format it with the
camcorder.
❍ Makes sure to insert the memory card you wish to format into the camcorder.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
CARD OPERATIONS
FORMAT
(
43)
1. Open the menu and select [CARD OPERATIONS].
2. Select [FORMAT].
[CANCEL] and [EXECUTE] appears.
3. Select [EXECUTE].
[FORMAT THIS CARD?], [NO] and [YES] appears.
4. Select [YES] and close the menu.
• Formatting starts.
• Selecting [NO] brings you back to step 3.
134
Connecting to a Computer Using a USB Cable
You can download images from the memory card to a computer using the supplied
USB cable. With the supplied software, you can easily download, browse and archive
images, and arrange still images for printout.
E
For instructions on how to connect the camcorder to the computer, and
install and operate the software, refer to the DIGITAL VIDEO SOLUTION
DISK Software Instruction Manual.
• Refer also to the computer instruction manual.
PC CONNECT
• “PC CONNECT
” appears to indicate that the camcorder is
connected to the computer via USB cable.
❍ Do not disconnect the USB cable, remove the memory card, change the
position of the POWER switch or turn off the camcorder and computer while
data is being transferred to the computer (while the camcorder’s card access
indicator is flashing). Doing so may damage the memory card’s data.
❍ Operation may not work correctly depending on the software and the
specifications/settings of your computer.
❍ The image file on your memory card and the image files saved on the hard disk
drive of your computer are valuable, original data files. If you wish to use
image files on your computer, make copies of them first, and use the copied
file, retaining the original.
❍ We recommend powering the camcorder from a household power source
while it is connected to the computer.
❍ For transferring recordings from to a computer using a DV cable, see p. 100.
❍ Still images/movies recorded on a tape cannot be transferred to a computer via
USB interface.
135
Creating a Start-up Image
You can create a start-up image using a still image on the memory card or a sample
start-up image provided on the DIGITAL VIDEO SOLUTION DISK and save it as [MY
IMAGE1] or [MY IMAGE2].
E
❍ Make sure to insert a memory card with enough remaining capacity.
❍ Before you create a start-up image, you need to record a still image on the
memory card.
❍ Retain the original data of the still image you have set as the start-up image on
your computer or removable disk.
Preparations
Record a still image on the memory card.
OR
Upload a still image from your computer to the memory card using the
software in the DIGITAL VIDEO SOLUTION DISK.
For instruction on how to upload a still image to the memory card, refer to Adding Still
Images from Your Computer to the Memory Card in the DIGITAL VIDEO SOLUTION DISK
Software Instruction Manual.
Setting the Still Image as Start-up Image
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY (VCR)
MY CAMERA
CREATE START–UP IMAGE
(
43)
1. Open the menu.
2. Select [MY CAMERA].
3. Select [CREATE START-UP IMAGE].
[SET THIS AS START-UP IMAGE1?], [YES] and [NO] appears.
4. Select a still image with the CARD +/– buttons and select [YES].
[SAVE AS MY IMAGE1], [MY IMAGE2] and [CANCEL] appears.
5. Select [MY IMAGE1].
[OVERWRITE MY IMAGE1?], [YES] and [NO] appears.
6. Select [YES].
• The still image will be saved, and the image that was saved to [MY IMAGE1] is erased.
• Select this image as start-up image following the procedure in Customizing the
Camcorder (
49).
136
Memory Card Information
Images recorded on a memory card with this camcorder can be transferred to a
computer using the following products for SD Memory Cards or MultiMediaCards:
E
PC Card Adapter: An adapter to insert a memory card into the card slot on the
computer.
USB Reader/Writer: Connects to the USB port of a computer for direct access to the
memory card.
FD Adapter:
An adapter to insert a memory card into the floppy disk drive on
the computer.
Memory Cards that are confirmed to operate with this camcorder
(as of February 2003):
SD Memory Card: Panasonic: 16 MB, 32 MB, 64 MB, 128 MB, 256 MB, 512 MB
SanDisk: 16 MB, 32 MB, 64 MB
MultiMediaCard: SanDisk: 16 MB, 32 MB, 64 MB
However, we cannot guarantee that all of these memory cards work properly.
Memory Card Handling Precautions
❍ Format new memory cards with the camcorder. Memory cards formatted with other
devices such as a computer may not operate correctly.
❍ We recommend saving backups of memory card images on your computer’s hard drive
or other external memory device. Image data may be corrupted or lost due to memory
card defects or exposure to static electricity. Canon Inc. makes no warranties for
corrupted or lost data.
❍ Do not turn off the camcorder, disconnect the power source or remove the memory
card while the card access indicator is flashing.
❍ Do not use memory cards in places subject to strong magnetic fields.
❍ Do not leave memory cards in places subject to high humidity and high temperature.
❍ Do not disassemble memory cards.
❍ Do not bend, drop, or subject memory cards to shocks and do not expose them to
water.
❍ Moving a memory card rapidly between hot and cold temperatures may cause
condensation to form on its external and internal surfaces. If condensation forms on
the card, put it aside until the droplets have evaporated completely.
❍ Do not touch or expose the terminals to dust or dirt.
❍ Store and carry memory cards in the supplied case to protect the terminals.
❍ Check the direction before inserting the memory card. Forcing a memory card
backwards into the slot may damage the memory card or the camcorder.
❍ Do not remove the label from the memory card, or affix other labels on the memory
card. If you wish to add labels, affix them to the case.
137
Sample Images
27 sample images are pre-recorded on the supplied SD Memory Card: 8 card chroma
key images, 5 card luminance key images, 2 camera chroma key images and 12 card
animation images.
E
Card Chroma Key
Card Luminance Key
Camera Chroma Key
Card Animation
138
The sample images recorded on the supplied SD Memory Card are intended only
for the personal use with this camcorder. Do not use these sample images for
other purposes.
E
If you have mistakenly erased the sample images on the supplied SD Memory
Card, they can be downloaded from the homepage http://www.canondv.com.
For details on how to add the downloaded images to the memory card, refer to
Adding Still Images from Your Computer to the Memory Card in the DIGITAL
VIDEO SOLUTION DISK Software Instruction Manual.
If you cannot use the USB cable to connect the camcorder to a computer, you will
need a PC Card Adapter to upload the images to a memory card.
PhotoEssentials – Royalty Free Stock Photography
The PhotoEssentials suite of royalty-free images on CD-ROM features premium quality assignment
photography and is ideally suited for use in advertising, brochures, reports, multimedia, websites,
books, packaging and more.
For more information, please visit their website www.photoessentials.com
139
Screen Displays
LCD Screen Displays
You can hide the displays on the LCD screen to have a clear screen for playback.
E
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY (VCR)
DISPLAY SET UP
DISPLAYS•••••ON
(
43)
Open the menu and select [DISPLAY SET UP]. Select [DISPLAYS], set it to
[OFF <PLAYBK>] and close the menu.
• The LCD screen will become completely blank (also the TV screen if connected).
• Warning messages still appear, and the data code appears if turned on.
• Tape operation displays appear for 2 seconds.
• Displays cannot be hidden on the index screen.
TV Screen Displays
When you connect a TV for recording/playback, you can hide the displays on the TV
screen. For connecting instructions, see Playing Back on a TV Screen (
40).
CAMERA
PLAY (VCR) CARD CAMERA
CARD PLAY (VCR)
Press the TV SCREEN button on the wireless controller.
SELF T. D.EFFECT.
MENU
SET
ON/OFF
TV SCREEN
• When the POWER switch is set to CAMERA: The displays
disappear from the TV screen and appear when you press the
button again.
INDEX SLIDE SHOW
CARD
DATA CODE SEARCH SELECT
• When the POWER switch is set to PLAY (VCR): The displays appear on the connected TV
screen and disappear when you press the button again. The setting resets to the OFF
setting when you turn the camcorder off.
When the TV screen displays are hidden, the displays still appear on the LCD screen. If
you turn on the data code, displays other than the data code will disappear from the LCD
screen.
You can also change the setting in the menu during recording:
PLAY (VCR)
CARD PLAY (VCR)
CAMERA
CARD CAMERA
DISPLAY SET UP
TV SCREEN••••ON
(
43)
Open the menu and select [DISPLAY SET UP]. Select [TV SCREEN], set it to
[OFF] and close the menu.
140
Screen Displays during Basic Recording/Playback
indicates flashing.
E
CAMERA mode (battery pack attached):
• Remote sensor mode and audio mode disappear after 4
seconds.
SP PAUSE
0:00:00
5min
1
12bit
PLAY (VCR) mode:
STEREO1
SP STOP
0:00:00:00:00
5min
• Remote sensor mode and volume bar disappear after 4
seconds.
1
: Fast forward playback/
rewind playback ( 38)
: ×2 playback
RTN
RTN
REC
/
/
: Zero set memory (forward
and reverse) ( 87)
PAUSE
STOP
EJECT
PLAY
FF
2
1
2
1
/
/
: AV insert editing ( 95)
: Audio dubbing ( 97)
(forward and reverse) ( 38)
: ×1 playback
/
/
(forward and reverse) ( 38)
: Slow playback
(forward and reverse) ( 38)
: Frame advance playback/
frame reverse playback ( 38)
: Playback pause
REW
/
/
/
(forward and reverse) ( 38)
: Date search/photo search ( 86)
/
STEREO1
PAUSE
1:23:45:00
END
Time code ( 87)
Remaining tape
: Backup
battery ( 19)
Remaining battery charge ( 18)
: Condensation
warning ( 148)
1
16bit
Remote sensor mode ( 48)
Audio mode ( 69)
141
Screen Displays during Advanced Recording/Playback
CAMERA Mode
E
Recording reminder ( 29)/
Self-timer countdown ( 68)/
Photo recording timer ( 53)
Image stabilizer ( 67)
Zoom ( 30)
Recording mode
Exposure level ( 78)
Program AE ( 55)
Manual focus ( 76)
Shutter speed ( 79)
White balance ( 81)
Card mix ( 128)
(
52)
W
T
SP
Self-timer ( 68)
Headphones ( 70)
0
1sec
E.LOCK
MF
1/100
Wind screen ( 69)
Audio mode ( 69)
CARD MIX
FADE–T
WSON
12bit
16:9
Digital effects ( 59)
12:00 PM
JAN.1,2003
16:9 mode ( 50)
Photo mode ( 53)
PHOTO
Date and time ( 84)
AF/AE locked in
Photo mode ( 53)
Accessory attached to
the Advanced Accessory
shoe ( 71)
PLAY (VCR) Mode
Photo search/
Date search ( 86)
MIX/VARI.
1
12bit audio out ( 99)
1
10
10
1
PHOTO SEARCH
Photo search/
Volume level of built-in
speaker or headphones
Date search ( 86)/
AV insert ( 95)/
Audio dubbing ( 97)
F1.8
(
39)
1/1000
12bit
DV IN
12:00 PM
JAN.1,2003
Audio mode ( 69)
DV input ( 91)
Data code ( 84)
142
CARD CAMERA Mode
Stitch assist ( 111)
Movie recording timer
113) /
Self-timer countdown
68)
(
E
(
Zoom ( 30)
Card access display ( 105)
Still image quality ( 102)
Remaining card capacity
Program AE ( 55)
W
T
S.FINE
50
(
102)
1 2
1sec
0
Exposure level ( 78)
Manual focus
E.LOCK
MF
1/100
1280
320
Still image size ( 102)
Movie size ( 103)
Self-timer ( 68)/
(
76)
Shutter speed
79)
White balance
81)
12:00 PM
JAN.1,2003
Movie recording ( 113)
•
(
CLOSE
Stitch assist ( 111)
(
Date and time ( 84)
Accessory attached to
the Advanced Accessory
shoe ( 71)
AF/AE locked in
Photo mode ( 105)
CARD PLAY (VCR) Mode
Print order ( 120)
Protect mark ( 118)
Folder number-
File number ( 103)
Slide show ( 116)
Card access display
SLIDE SHOW
101–0143
43/50
Current image/
total images
640 480
(
115)
12:00 PM
JAN.1,2003
Data code ( 84)
143
List of Messages
Message
Explanation
E
SET THE TIME ZONE,
DATE AND TIME
You have not set the time zone, date and time. This message 25
appears each time you turn the power on until you set the
time zone, date and time.
CHANGE THE
BATTERY PACK
Battery pack is exhausted. Replace or charge the battery
pack.
16
THE TAPE IS SET FOR
Cassette is protected. Replace the cassette or change the
23
ERASURE PREVENTION position of the protect switch.
REMOVE THE
CASSETTE
Camcorder stopped operating to protect the tape. Unload
and reload the cassette.
22
CHECK THE DV INPUT DV cable is not connected, or the connected digital device is
turned off.
89
CONDENSATION HAS Condensation has been detected in the camcorder.
BEEN DETECTED
148
22
TAPE END
Tape reached the end. Rewind the tape or replace the
cassette.
CHECK THE CASSETTE You attempted to perform audio dubbing or AV insert on a
[REC MODE] tape recorded in a mode other than the SP mode.
CHECK THE CASSETTE You attempted to perform audio dubbing on a tape
[AUDIO MODE] recorded in 16-bit or 12-bit 4-channel sound.
CHECK THE CASSETTE You attempted to perform audio dubbing or AV insert on a
52
97
95
[BLANK]
tape with a blank section.
HEADS DIRTY, USE
CLEANING CASSETTE
Video heads are dirty. Clean the video heads.
148
92
COPYRIGHT PROTECTED
PLAYBACK IS RESTRICTED
You attempted to play back a copyright protected tape.
You attempted to dub a copyright protected tape. May also
COPYRIGHT
92
PROTECTED DUBBING appear when an anomalous signal is received during analog
RESTRICTED
line-in recording, or during analog-digital conversion of a
copyright protected tape.
144
Memory Card Related Messages
Message
Explanation
NO CARD
Memory card not is inserted into the camcorder.
101
101
E
THE TAPE IS SET FOR
SD Memory Card is set for erasure prevention. Replace the
ERASURE PREVENTION card or change the position of the protect switch.
NO IMAGES
No images are recorded on the memory card.
115
CARD ERROR
A memory card error occurred. The camcorder cannot record 101
or play back the image.
The error may be temporary. If the message disappears after
4 seconds and flashes red, turn the camcorder off, remove
the card and reinsert the card. If
can continue recording/playback.
changes to green, you
CARD FULL
No remaining capacity on the memory card. Replace with
another card or erase images.
119
NAMING ERROR
File or folder number has reached the maximum value.
103
115
UNIDENTIFIABLE
IMAGE
Image is recorded in a not compatible JPEG format or
another format not compatible with the camcorder, or the
image file is corrupted.
PRINT ORDER
ERROR
You attempted to set more than 200 still images in the print 120
order.
THIS IMAGE CANNOT Some analog images cannot be recorded on the memory
BE RECORDED card depending on the signal.
109
145
Direct Print Related Messages
Message
Explanation
No Paper
Paper cassette is not correctly inserted or is out of paper.
The paper jammed during printing.
E
Paper Jam
No Ink
The ink cartridge is not inserted or is out of ink.
There is a problem with the ink cassette.
The printer battery is depleted.
Ink Cassette Error
Recharge the printer
battery
Communication Error The printer is experiencing a data transmission error.
Could not print X
images
You attempted to use the print order settings to print X
images that were made with another camcorder, have a
different format or were edited on a computer.
Cannot Print!
You attempted to print an image that was made with
another camcorder, has a different format, or was edited on
a computer.
Set print order
Cannot trim
You attempted to print an image from the CARD PLAY (VCR)
menu [\ PRINT] without having set the print order.
You attempted to trim an image with an image size of
160 ×120.
Readjust trimming
You changed the print style after you set the trimming
settings.
Paper has been
changed
Paper size has been changed between print setting and start
of printing.
Incompatible paper
size
You attempted to print on paper that cannot be used with
the camcorder.
Paper and ink do not
match
The ink cannot be used with the selected paper type.
Printer in use
The printer is printing from a computer or a memory card
inserted into the printer. It automatically starts printing
from the camcorder when current prints are complete.
Printer warming up
Printer is warming up. The printer automatically starts
printing when it is ready.
No printhead
No print head is installed in the printer.
Printer cover open
Media type error
Printer cover is open. Close the printer cover securely.
Wrong paper. Cancel printing and set the paper you chose in
the print settings menu.
Paper lever error
Low ink level
Paper lever error occurred. Adjust the paper selection lever
to the proper position.
The ink tank needs to be replaced soon. Prepare a new ink
tank. If you select [Continue] in the error screen, you can
restart printing.
Waste tank full
Printer error
Waste tank is full. You can restart printing by pressing the
RESUME/CANCEL button on the Bubble Jet Printer. Request
replacement of the waste tank at the shop where you
purchased the printer or the nearest Canon customer
support center listed in the Bubble Jet Quick Start Guide.
Turn off the printer and turn it back on. If the error persists,
consult the nearest Canon customer support center listed in
the Bubble Jet Quick Start Guide.
146
Maintenance
Camcorder Handling Precautions
E
❍ Do not carry the camcorder by the LCD panel or viewfinder.
❍ Do not leave the camcorder in places subject to high temperatures, such as a sun-
heated car, and high humidity.
❍ Do not use the camcorder in places subject to magnetic or electric fields such as
near the TV transmitters or portable communication devices.
❍ Do not point the lens or viewfinder at strong light sources. Do not leave the
camcorder pointed at a bright subject.
❍ Do not use the camcorder in dusty or sandy places. Dust or sand getting inside the
cassette or camcorder may cause damage. Dust and sand can also damage the lens.
Attach the lens cap after use.
❍ The camcorder is not waterproof. Water, mud or salt getting inside the cassette or
camcorder may cause damage.
❍ Be careful of heat generated by lighting equipment.
❍ Do not disassemble the camcorder. If the camcorder does not function properly,
consult qualified service personnel.
❍ Handle the camcorder with care. Do not subject the camcorder to shocks or
vibration as this may cause damage.
❍ Avoid sudden changes in temperature. Moving the camcorder rapidly between hot
and cold temperatures may cause condensation to form on its internal surfaces
(
148).
Storage
❍ If you do not intend to use the camcorder for a long time, store it in a place free of
dust, in low humidity, and at temperatures not higher than 86˚F (30˚C).
❍ After storage, check the functions of your camcorder to make sure that the
camcorder is still working properly.
Cleaning
Camcorder Body and Lens
❍ Use a soft, dry cloth to clean the camcorder body and lens. Never use chemically
treated cloth or volatile solvents such as paint thinner.
LCD Screen
❍ Clean the LCD screen using a commercially available cleaning cloth for glasses.
❍ Condensation may form on the surface of the screen when the temperature
changes suddenly. Wipe it with a soft dry cloth.
147
❍ At cold temperatures, the screen may be darker than usual. This is not a
malfunction. The screen returns to normal when the camcorder warms up.
E
Video Heads
❍ When the message “HEADS DIRTY, USE CLEANING CASSETTE” appears, or when
the playback picture becomes distorted, the video heads need to be cleaned.
❍ To maintain the best picture quality, we recommend cleaning the video heads
frequently with the Canon DVM-CL Digital Video Head Cleaning Cassette or a
commercially available dry cleaning cassette.
❍ Do not use wet type cleaning cassettes as this may damage the camcorder.
Condensation
Moving the camcorder rapidly between hot and cold temperature may cause
condensation (water droplets) to form on its internal surfaces. Stop using the
camcorder if condensation is detected. Continued use may damage the camcorder.
Condensation may form in the following cases:
When the camcorder is moved from an
air-conditioned room to a warm, humid
place
When the camcorder is moved from a
cold place to a warm room
When the camcorder is left in a humid
room
When a cold room is heated rapidly
How to avoid condensation:
❍ Unload the cassette, place the camcorder in an airtight plastic bag and let it adjust
to temperature changes slowly before removing it from the bag.
148
When condensation is detected:
❍ The camcorder stops operating and the warning message “CONDENSATION HAS
BEEN DETECTED” appears for approx. 4 seconds and h starts flashing.
❍ If a cassette is loaded, the warning message “REMOVE THE CASSETTE” appears and
v starts flashing. Remove the cassette immediately and leave the cassette
compartment open. Leaving the cassette in the camcorder may damage the tape.
❍ A cassette cannot be loaded when condensation is detected.
E
Resuming use:
❍ It takes about 1 hour until the water droplets evaporate. After the condensation
warning stops flashing, wait for 1 more hour before resuming use.
Using the Camcorder Abroad
Power Sources
You can use the compact power adapter to operate the camcorder and to charge
battery packs in any country with power supply between 100 and 240 V AC, 50/60 Hz.
Consult the Canon Service Center for information on plug adapters for overseas use.
Playback on a TV Screen
You can only play back your recordings on TVs with NTSC system. The NTSC system is
used in the following countries/areas:
American Samoa, Antigua, Aruba, Bahamas, Barbados, Bermuda, Bolivia, Canada,
Chile, Columbia, Costa Rica, Cuba, Ecuador, El Salvador, Guam, Guatemala, Greenland,
Haiti, Honduras, Jamaica, Japan, Korea, Mexico, Micronesia, Myanmar, Nicaragua,
Panama, Peru, Philippines, Puerto Rico, Saint Kitts and Nevis, Saint Lucia, Saint Vincent
and the Grenadines, Surinam, Taiwan, Trinidad and Tobago, USA, Venezuela, Virgin
Islands.
149
Troubleshooting
If you have a problem with your camcorder, refer to this checklist. Consult your dealer
or a Canon Service Center if the problem persists.
E
Power Source
Problem
Cause
Solution
Camcorder will not turn Battery pack is exhausted.
on.
Replace or charge the
battery pack.
16
16
16
28
16
22
16
–
Battery pack is not correctly Attach the battery pack
attached.
correctly.
The camcorder switches Battery pack is exhausted.
off by itself.
Replace or charge the
battery pack.
Power save function has
been activated.
Turn on the camcorder.
Cassette compartment
will not open.
Battery pack is exhausted.
Replace or charge the
battery pack.
Cassette compartment cover Open the cassette
is not fully open.
compartment cover fully.
Cassette compartment
stopped during loading/
unloading.
Battery pack is exhausted.
Replace or charge the
battery pack.
The camcorder
malfunctions.
Consult a Canon Service
Center.
LCD/viewfinder switches Battery pack is exhausted.
on and off.
Replace or charge the
battery pack.
16
Recording/Playback
28
22
16
Buttons will not work.
Camcorder is not turned on. Turn on the camcorder.
Cassette is not loaded.
Load a cassette.
k flashes on the
Battery pack is exhausted.
Replace or charge the
battery pack.
screen.
148
22
h flashes on the screen. Condensation is detected.
See reference page.
“Remove the cassette”
appears on the screen.
Camcorder stopped
operating to protect the
tape.
Unload and reload the
cassette.
48
24
The wireless controller
will not work.
Camcorder and wireless
controller are not set to the modes.
same remote sensor mode.
Change the remote sensor
Batteries of the wireless
controller are exhausted.
Replace the batteries.
150
Recording
Problem
Cause
Solution
Image will not appear
on the screen.
Camcorder is not set to
CAMERA mode.
Set the camcorder to
CAMERA mode.
28
25
E
“Set the time zone, date Time zone, date and time
and time” appears on
the screen.
Set the time zone, date and
time, or replace the backup
battery and reset the date
and time.
are not set, or the backup
battery is exhausted.
Pressing the start/stop
button will not start
recording.
Camcorder is turned off.
Cassette is not loaded.
Turn on the power.
Load a cassette.
28
22
22
Tape reached the end (
flashes on the screen).
Rewind the tape or replace
the cassette.
Cassette is protected (v
Replace the tape or change
the position of the protect
switch.
23
flashes on the screen).
Camcorder is set to a mode
other than the CAMERA mode. CAMERA mode.
Set the camcorder to
28
76
20
Camcorder will not
focus.
Autofocus does not work on Focus manually.
that subject.
Viewfinder is not adjusted.
Adjust the viewfinder with
the diopter adjustment lever.
Lens is dirty.
Clean the lens.
147
–
A vertical light bar
appears on the screen.
Bright light in a dark scene
may cause a vertical light
bar (smear) to appear. This is
not a malfunction.
– – –
– – –
Sound is distorted or
recorded in a lower
volume than the actual
volume.
When recording near loud
sound (such as fireworks,
drums or concerts), sound
may become distorted or
may not be recorded in the
actual sound level. This is
not a malfunction.
–
Viewfinder picture is
blurred.
Viewfinder is not adjusted.
Adjust the viewfinder with
the diopter adjustment lever.
20
37
Playback
Pressing the playback
button does not start
playback.
Camcorder is turned off, or is Set the camcorder to PLAY
not set to PLAY (VCR) mode. (VCR) mode.
22
37
Cassette is not loaded.
Load a cassette.
Rewind the tape.
Tape reached the end (
flashes on the screen).
70
94
40
Image will not appear
on the TV screen.
[AV/PHONES] is set to
[PHONESH] in the menu.
Set [AV/PHONES] to [AV] in
the menu.
[AV / DV OUT] is set to
[ON].
Set [AV / DV OUT] to [OFF].
Tape is running, but
image will not appear
on the TV screen.
TV/VIDEO selector on the TV Set the selector to VIDEO.
is not set to VIDEO.
148
92
Video heads are dirty.
Clean the video heads.
You attempted to play back Stop playback/dubbing.
or dub copyright protected
tape.
39
No sound from the built- Speaker volume is turned
in speaker. off.
Adjust the volume with the
selector dial.
151
Memory Card Operation
Problem
Cause
Solution
Memory card cannot be Memory card was not facing Turn the memory card over
inserted. the correct direction. and reinsert it.
101
E
Memory card cannot be Memory card is full.
recorded.
Replace the memory card or 119
erase images.
Memory card is not
formatted.
Format the memory card.
134
Memory card is not inserted. Insert a memory card.
101
103
File number reached
maximum value.
Set [FILE NUMBERS] to
[RESET] and insert a new
memory card.
SD Memory Card is
protected.
Change the position of the
protect switch.
101
115
Memory card cannot be Camcorder is not set to
Set the camcorder to CARD
PLAY (VCR) mode.
played back.
CARD PLAY (VCR) mode.
Memory card is not inserted. Insert a memory card.
101
118
101
Image cannot be erased. Image is protected.
Cancel the protection.
SD memory card is
protected.
Change the position of the
protect switch.
flashes red.
Card error occurred.
Turn off the camcorder.
Remove and reinsert the
memory card. Format the
memory card if flashing
persists.
134
152
(Availability differs from area to area)
System Diagram
E
WS-20 Wrist Strap
WD-H37 Wide-
converter
BP-500 Series
Battery Pack
CG-570
Battery Charger
SS-800 Shoulder Strap
CB-570
Car Battery Cable
TL-H37 Tele-
converter
CA-570 Compact
Power Adapter
WL-D79 Wireless MiniDV
Controller
Video
Cassette
FS-H37U
Filter Set
CA-570 Compact
Power Adapter
BP-500 Series
Battery Pack
VFL-1 Video Flash Light
S-150 S-video Cable
TV
VL-3 Video Light
STV-250N
Stereo Video Cable
VCR
Commercially available
DV Cable
Digital Device
DM-50 Directional
Stereo Microphone
PC Card Adapter
USB Reader/Writer
FD Adapter
SD Memory Card
BP-900 Series
Battery Pack*
VL-10Li Battery
Video Light
MultiMediaCard
Stereo Microphone
(commercially available)
IFC-300PCU USB Cable
Computer
SC-1000 Soft
Carrying Case
SC-A50 Soft
Carrying Case
Canon printers with
direct print function
* Charging with the CA-920 Compact Power Adapter or CH-910 Dual Battery
Charger/Holder (both optional)
153
Optional Accessories
Call or visit your local retailer/dealer for genuine Canon video accessories. You can also
obtain genuine accessories for your Canon camcorder by calling: 1-800-828-4040,
Canon U.S.A. Information Center.
E
BP-500 Series Battery Packs
BP-512
BP-522
BP-535
When you need extra battery packs, select from
the following: BP-511, BP-512, BP-522 or BP-535.
CG-570 Battery Charger
The battery charger can be used with the
supplied CA-570 Compact Power Adapter or the
optional CB-570 Car Battery Cable to charge
BP-500 series battery packs.
Battery Pack
Charging Time
55 min.
BP-508 (OPTURA10)
BP-512 (OPTURA20/optional)
BP-511 (Optional)
BP-522 (Optional)
BP-535 (Optional)
95 min.
95 min.
140 min.
205 min.
CB-570 Car Battery Cable
Use the car battery cable with the CG-570
Battery Charger to charge battery packs on the
move. The car battery cable plugs into your
car’s cigarette lighter and runs off a 12-24 V DC
negative ground battery.
TL-H37 Tele-converter
This tele-converter lens increases the focal
length of the camcorder lens by a factor of 1.5.
• The image stabilizer is not as effective when
the tele-converter is attached.
• The image quality may be degraded at the telephoto side.
• The minimum focusing distance with the Tele-converter is 8.2 ft (2.5 m); 0.98 in.
(2.5 cm) at maximum wide angle.
154
WD-H37 Wide-converter
This lens decreases focal length by a factor of
0.7, giving you a wide perspective for indoor
shots or panoramic views.
E
FS-H37U Filter Set
Neutral density and MC protector filters help
you to control difficult lighting conditions.
VL-10Li Battery Video Light
This compact yet powerful video light can be
used for both indoor and outdoor shooting. It
attaches to the camcorder’s accessory shoe and
is powered by BP-900 series battery packs.
• Approximate usage time: BP-915: 60 min., BP-930: 120 min., BP-945: 170 min.
• BP-900 series battery packs are charged with the CA-920 Compact Power Adapter.
VFL-1 Video Flash Light
This video flash light allows you to record still
images and movies even at night or in dark
places. It attaches to the camcorder’s advanced
accessory shoe for cable-free operation.
VL-3 Video Light
This video light enables you to record brightly
in color even in dark places. It attaches to the
camcorder’s advanced accessory shoe for cable-
free operation.
DM-50 Directional Stereo Microphone
This highly sensitive, super-directional
microphone attaches to the camcorder’s
advanced accessory shoe. It can be used as
directional microphone (monaural) or stereo
microphone.
WS-20 Wrist Strap
Use this for extra additional protection for
active shooting.
155
SC-1000 Soft Carrying Case
A handy camcorder bag with padded
compartments and plenty of space for
accessories.
E
SC-A50 Soft Carrying Case
This lightweight bag keeps the camcorder
within easy reach without weighing you down
or getting in the way.
E
N
N
This mark identifies genuine Canon video accessories. When you
use Canon video equipment, we recommend Canon-brand
accessories or products bearing the same mark.
O
U
N
IN
A
C
E
Y
I
D
E
R
O S
O
S
A
C
E
Provided Accessories:
WL-D79 Wireless Controller
D83-0622-000
D81-1430-000
D52-0220-000
9468A002AA
6760A002AA
D85-1360-000
SS-800 Shoulder Strap
Lens Cap
CA-570 Compact Power Adapter
BP-512 Battery Pack (OPTURA20)
BP-508 Battery Pack (OPTURA10)
STV-250N Stereo Video Cable
IFC-300PCU USB Cable
3067A002AA (D82-0590-201)
6906A001AA
Optional Accessories:
BP-511 Battery Pack
BP-522 Battery Pack
3055A002AA (D85-1112-201)
3174A002AA (D85-1122-201)
6741A002AA
BP-535 Battery Pack
SC-1000 Soft Carrying Case
SC-A50 Soft Carrying Case
WD-H37 Wide-converter
TL-H37 Tele-converter
3083A002AA (D81-1200-201)
D81-1302-201
8836A001AA
8835A001AA
FS-H37U Filter Set
8837A001AA
DM-50 Directional Stereo Microphone
VFL-1 Video Flash Light
VL-3 Video Light
VL-10Li Battery Video Light
JR 7.2V 10WF Halogen Bulb
WS-20 Wrist Strap
3176A002AA (D84-0120-201)
8834A001AA
3175A002AA (D86-0121-201)
3140A002AA (D86-0081-201)
3141A002AA (D86-0090-201)
3118A002AA (D81-0190-202)
3134A002AA (D36-0032-201)
DVM-CL DV Cleaning Cassette
156
Specifications
OPTURA20/OPTURA10
E
Power supply (rated):
7.4 V DC
Power consumption
(AF turned on):
OPTURA20: 3.4 W (using viewfinder), 4.6 W (using LCD screen)
OPTURA10: 3.4 W (using viewfinder), 4.4 W (using LCD screen)
Television system:
EIA standard (525 lines, 60 fields) NTSC color signal
Video recording system:
2 rotary heads, helical scanning DV system (Consumer digital VCR
SD system); Digital component recording
Audio recording system:
Image sensor:
Tape: PCM digital sound: 16 bit (48 kHz/2 ch); 12 bit (32 kHz/4 ch)
Card: ADPCM digital sound: 16 bit (16 kHz/1 ch), 4 bit
1/4“ CCD (charge coupled device), approx. 1,330,000 pixels
(Effective pixels: tape: approx. 690,000 pixels, card: approx.
1,230,000 pixels)
Tape format:
Tape speed:
Videocassettes bearing the “MiniDV” mark.
SP: 0.74 ips (18.81 mm/s), LP: 0.49 ips (12.56 mm/s)
SP: 80 min., LP: 120 min.
Maximum recording time
(80 min. cassette):
Fast forward/rewind time:
Lens:
Approx. 2 min. 20 sec. (with a 60 min. cassette)
F1.8-3.0, 16× power zoom, f=4.0-64.0 mm; (card: F1.8-3.0,
15× power zoom, f=4.3-64.0 mm)
Focusing system:
TTL autofocus, manual focusing possible
Minimum focusing distance: 3.3 ft. (1 m), 0.39 in. (1 cm) on maximum wide angle
Maximum shutter speed:
Minimum illumination:
1/8,000 sec. (1/250 sec. when using a memory card)
0.5 lx (using the Night mode in CAMERA mode)
Recommended illumination: More than 100 lx
Filter diameter:
Viewfinder:
LCD screen:
37 mm
0.33 in., TFT color LCD, approx. 113,000 pixels
OPTURA20: 3.5 in., TFT Color, approx. 123,000 pixels
OPTURA10: 2.5 in., TFT Color, approx. 112,000 pixels
Microphone:
Stereo electret condenser microphone
SD Memory Card, MultiMediaCard
Recording media:
Number of recording pixels:
Still image: 1280 × 960, 640 × 480 pixels
Movie: 320 × 240 pixels (approx. 10 sec.), 160 × 120 pixels
(approx. 30 sec.), 15 frames/sec.
The figures in brackets represent the maximum length of one
movie clip.
Estimated SD Memory Card 1280 × 960: Superfine: 6 images/Fine: 10 images/Normal 18
SDC-8M capacities:
images;
640 × 480: Superfine: 34 images/Fine 50 images/Normal 84 images
The actual number varies according to the images. Sample images recorded on the supplied SD
Memory Card are to be included in the total number.
File format:
Design rule for Camera File system (DCF), Exif 2.2 compliant,
Digital Print Order Format (DPOF) compliant (still images only)
This camcorder supports Exif 2.2 (also called “Exif Print”). Exif Print is a standard for enhancing the
communication between camcorders and printers. By connecting to an Exif Print-compliant printer,
the camcorder’s image data at the time of shooting is used and optimized, yielding extremely high
quality prints.
Image format:
Still image: JPEG (Compression mode: Superfine, Fine, Normal),
Movie: Motion JPEG
157
USB terminal:
mini-B
DV terminal input/output:
AV terminal input/output:
Special 4-pin connector (IEEE 1394 compliant)
ø3.5 mm minijack
Audio input: -10 dBV/40 kohms or more
Audio output: -10 dBV (47 kohm load)/3 kohms or less
E
Video:
1 Vp-p/75 ohms unbalanced
S-video terminal
input/output:
1 Vp-p/75 ohms (Y signal), 0.286 Vp-p/75 ohms (C signal)
MIC terminal input:
ø3.5 mm stereo mini-jack
–57 dBV (with 600 ohm mic)/5 kohms or more
Headphone terminal:
Operating temperatures:
Dimensions:
ø3.5 mm stereo minijack
32 – 104˚F (0 – 40˚C)
3 × 7.3 × 3.6 in. (75 × 186 × 92 mm)
OPTURA20: 1.4 lb. (625 g), OPTURA10: 1.4 lb. (620 g)
Weight:
CA-570 Compact Power Adapter
Power supply:
Power consumption:
Rated output:
100 – 240 V AC, 50/60 Hz
17W
8.4 V DC, 1.5 A
Operating temperature:
Dimensions:
32 – 104˚F (0 – 40˚C)
2.1 × 3.5 × 1.1 in. (52 × 90 × 29 mm)
4.8 oz. (135 g)
Weight:
BP-512/BP-508 Battery Pack
Battery type:
Rechargeable Lithium Ion Battery
Rated voltage:
Operating temperature:
Battery capacity:
Dimensions:
7.4 V DC
32 – 104˚F (0 – 40˚C)
BP-512: 1100 mAh, BP-508: 800 mAh
1.5 × 0.83 × 2.2 in. (38 × 21 × 55 mm)
BP-512: 2.5 oz. (70g), BP-508: 2.3 oz. (65g)
Weight:
SDC-8M SD Memory Card
Capacity:
8 MB
Interface:
SD Memory Card standard
32 – 104˚F (0 – 40˚C)
1.3 × 0.94 × 0.08 in. (32 × 24 × 2.1 mm)
0.07 oz. (2 g)
Operating temperature:
Dimensions:
Weight:
Weight and dimensions are approximate. Errors and omissions excepted. Subject to
change without notice.
158
Index
12bit audio . . . . . . . . . . . . . . . . . . 99
16:9 wide screen . . . . . . . . . . . . . . 50
6-second auto date . . . . . . . . . . . . 85
Digital effects . . . . . . . . . . . . . . . . 59
Digital zoom . . . . . . . . . . . . . . . . . 30
Direct print function . . . . . . . . . . 122
DV dubbing. . . . . . . . . . . . . . . . . . 91
DV terminal. . . . . . . . . . . . . . 89, 100
E
A
Abroad, using the camcorder . . . 149
Accessories. . . . . . . . . . . . . . . . 9, 154
Advanced accessory shoe . . . . 71-75
AF assist lamp* . . . . . . . . . . . . . . . 77
Analog line-in . . . . . . . . . . . . . . . . 90
Analog-digital converter. . . . . . . . 93
Assist lamp*. . . . . . . . . . . . . . . 57, 77
Audio dubbing . . . . . . . . . . . . . . . 97
Audio mode . . . . . . . . . . . . . . . . . 69
Auto . . . . . . . . . . . . . . . . . . . . . . . 55
Auto Exposure Bracketing . . . . . 108
Autofocus . . . . . . . . . . . . . . . . . . . 76
AV insert . . . . . . . . . . . . . . . . . . . . 95
AV/DV . . . . . . . . . . . . . . . . . . . . . 93
AV/headphones terminal . . . . 39, 70
E
Easy recording. . . . . . . . . . . . . . . . 55
Effects . . . . . . . . . . . . . . . . . . . . . . 63
Erasing still images . . . . . . . . . . . 119
Exposure . . . . . . . . . . . . . . . . . . . . 78
F
Faders . . . . . . . . . . . . . . . . . . . . . . 60
Fast forward . . . . . . . . . . . . . . . . . 37
File numbers . . . . . . . . . . . . . . . . 103
Focusing . . . . . . . . . . . . . . . . . . . . 76
Focusing point. . . . . . . . . . . . . . . 106
Focus-priority . . . . . . . . . . . . . . . 107
Formatting . . . . . . . . . . . . . . . . . 134
B
G
Backup battery . . . . . . . . . . . . . . . 19
Battery charger . . . . . . . . . . . . . . 154
Battery pack . . . . . . . . . . . . . . . . . 16
Beep . . . . . . . . . . . . . . . . . . . . . . . 50
Brightness . . . . . . . . . . . . . . . . . . . 33
Grip belt . . . . . . . . . . . . . . . . . . . . 20
H
Headphones . . . . . . . . . . . . . . 39, 70
I
Image quality . . . . . . . . . . . . . . . 102
Image stabilizer. . . . . . . . . . . . . . . 67
Index screen . . . . . . . . . . . . . . . . 116
C
Card animation . . . . . . . . . . . . . . 129
Card mix . . . . . . . . . . . . . . . . . . . 128
Computer . . . . . . . . . . . . . . 100, 135
Condensation . . . . . . . . . . . . . . . 148
Connections - TV. . . . . . . . . . . . . . 40
Connections - VCR. . . . . . . . . . . . . 40
Continuous Shooting . . . . . . . . . 107
Copyright signals. . . . . . . . . . . . . . 92
Copying still images . . . . . . . . . . 132
L
LCD mirror mode . . . . . . . . . . . . . 33
LCD screen. . . . . . . . . . . . . . . . . . . 32
Lens cap . . . . . . . . . . . . . . . . . . . . 20
Low light mode. . . . . . . . . . . . . . . 56
Low light plus mode * . . . . . . . . . 57
LP mode . . . . . . . . . . . . . . . . . . . . 52
D
Data code . . . . . . . . . . . . . . . . . . . 84
Date and time. . . . . . . . . . . . . . . . 25
Date search . . . . . . . . . . . . . . . . . . 86
Demo mode . . . . . . . . . . . . . . . . . 51
M
Magnifying the image . . . . . . . . . 83
Maintenance . . . . . . . . . . . . . . . . 147
Manual focus . . . . . . . . . . . . . . . . 76
* OPTURA20 only
159
Memory card. . . . . . . . . . . . . . . . 101
Menus . . . . . . . . . . . . . . . . . . . 43-47
Microphone. . . . . . . . . . . . . . . . . . 69
MIC terminal . . . . . . . . . . . . . . . . . 69
Movie size . . . . . . . . . . . . . . . . . . 103
MultiMediaCard . . . . . . . . . . . . . 101
Multi-image screen . . . . . . . . . . . . 65
My Camera settings . . . . . . . . . . . 49
Search select . . . . . . . . . . . . . . . . . 86
Self-timer . . . . . . . . . . . . . . . . . . . 68
Shutter sound . . . . . . . . . . . . . . . . 49
Shutter speed . . . . . . . . . . . . . . . . 79
Slide show . . . . . . . . . . . . . . . . . . 116
SP mode . . . . . . . . . . . . . . . . . . . . 52
Speaker . . . . . . . . . . . . . . . . . . . . . 39
Sports mode . . . . . . . . . . . . . . . . . 56
Spotlight mode . . . . . . . . . . . . . . . 56
Still image quality . . . . . . . . . . . . 102
Still image size . . . . . . . . . . . . . . 102
Stitch Assist mode . . . . . . . . . . . . 111
Super Night mode * . . . . . . . . . . . 57
E
N
Night mode. . . . . . . . . . . . . . . . . . 57
O
Output channel. . . . . . . . . . . . . . . 42
T
Tape protection. . . . . . . . . . . . . . . 23
Telephoto . . . . . . . . . . . . . . . . . . . 30
Time code . . . . . . . . . . . . . . . . . . 141
Time zone . . . . . . . . . . . . . . . . . . . 25
Tripod . . . . . . . . . . . . . . . . . . . . . . 36
Troubleshooting . . . . . . . . . . . . . 150
TV Screen. . . . . . . . . . . . . . . . 40, 140
P
Photo search . . . . . . . . . . . . . . . . . 86
Playback - Memory card . . . . . . . 115
Playback - Tape . . . . . . . . . . . . . . . 37
Playback pause . . . . . . . . . . . . . . . 38
Portrait mode . . . . . . . . . . . . . . . . 56
Power adapter . . . . . . . . . . . . . . . 15
Print order. . . . . . . . . . . . . . . . . . 120
Protect. . . . . . . . . . . . . . . . . . . . . 118
U
USB terminal . . . . . . . . . . . . . . . . 135
R
Record pause mode . . . . . . . . . . . 28
Record review . . . . . . . . . . . . . . . . 35
Record search . . . . . . . . . . . . . . . . 35
Recording Movies
V
Video. . . . . . . . . . . . . . . . . . . . . . . 40
Video heads. . . . . . . . . . . . . . . . . 148
Video ID-1 system . . . . . . . . . . . . . 40
Video light. . . . . . . . . . . . 71, 72, 155
Videocassettes. . . . . . . . . . . . . . . . 22
Viewfinder . . . . . . . . . . . . . . . . . . 20
(memory card). . . . . . . . . . . . . . 113
Recording Movies (tape). . . . . . . . 28
Recording programs . . . . . . . . . . . 55
Recording Still Images
(memory card). . . . . . . . . . . . . . 105
Recording Still Images (tape) . . . . 53
Recording to a VCR. . . . . . . . . . . . 88
Remote sensor. . . . . . . . . . . . . . . . 48
Rewind . . . . . . . . . . . . . . . . . . . . . 37
W
White balance. . . . . . . . . . . . . . . . 81
Wide screen. . . . . . . . . . . . . . . . . . 50
Wireless controller . . . . . . . . . . . . 24
Z
Zero set memory. . . . . . . . . . . . . . 87
Zooming . . . . . . . . . . . . . . . . . . . . 30
S
S1 video terminal . . . . . . . . . . . . . 40
Sample images . . . . . . . . . . . . . . 138
Sand & Snow mode. . . . . . . . . . . . 56
Screen displays . . . . . . . . . . . . . . 140
SD Memory Card . . . . . . . . . . . . . 101
* OPTURA20 only
160
U.S.A.
CANON® OPTURA20/OPTURA10 DIGITAL VIDEO CAMCORDER LIMITED
WARRANTY
E
The limited warranty set forth below is given by Canon U.S.A., Inc. (“CUSA”) with respect to each Canon
OPTURA20/OPTURA10 Digital Video Camcorder (“DV Camcorder”) purchased and used in the United States.
Each Canon DV Camcorder, when delivered to you in new condition in its original container, is warranted against defective
material or workmanship as follows: for a period of one (1) year from the date of original purchase (three (3) months in the
case of the video head part), defective parts or DV Camcorders returned to a CUSA factory service center (“CUSA Center”)
or an authorized DV Camcorder service facility (“Service Facility”), and proven to be defective upon inspection, will be
repaired or exchanged for new or comparable rebuilt parts or DV Camcorders. The warranty period for repaired or
replacement parts or DV Camcorders shall begin upon shipment of the same, but shall in no event exceed the original
warranty period of the defective part or DV Camcorder.
Non-Canon brand peripheral equipment and software which may be distributed with Canon DV Camcorders are
sold “AS IS”, without warranty of any kind by CUSA, including any implied warranty regarding merchantability
or fitness for a particular purpose. The sole warranty with respect to such non-Canon brand items is given by
the manufacturer or producer thereof.
CUSA shall have no responsibility under this limited warranty for use of Canon DV Camcorders in conjunction with
incompatible peripheral equipment and incompatible software.
In order to obtain warranty service, contact the authorized Canon retail dealer from whom you purchased the DV
Camcorder or call the CANON INFORMATION CENTER AT 1-800-828-4040 (which is open from 9:00 a.m. to 5:00 p.m.
(E.S.T.), Monday through Friday, excluding holidays). Have your unit serial number and your date of purchase available
when you make the call to expedite service. In either case you will be directed to ship the DV Camcorder, postage prepaid,
to the CUSA Center or Service Facility nearest to you. You must include a copy of the proof of purchase (bill of sale) and a
complete explanation of the problem. DV Camcorders covered by this limited warranty will be repaired and returned to you
without charge by the CUSA Center or the Service Facility. Repairs not under warranty will be at such cost as the CUSA
Center or Service Facility may from time to time generally establish.
This limited warranty covers all defects encountered in normal use of the DV Camcorder, and does not apply in the
following cases:
(a) Loss of or damage to the DV Camcorder due to abuse, mishandling, improper packaging by you, alteration, accident,
leaking batteries, exterior nicks, scratches or dents, electrical current fluctuations, failure to follow operating
instructions, maintenance and environmental instructions prescribed in CUSA’s instruction manual, or service performed
by other than a CUSA Center or Service Facility.
(b) Use of parts or supplies (other than those sold by CUSA) which cause damage to the DV Camcorder or cause
abnormally frequent service calls or service problems.
(c) If any DV Camcorder has had its serial number or dating altered or removed.
This limited warranty does not apply to accessories or consumables for the DV Camcorder, which are sold “AS IS”, without
warranty of any kind by CUSA.
NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, APPLIES TO THE DV CAMCORDER AFTER THE APPLICABLE PERIOD OF EXPRESS
WARRANTY STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY, EXCEPT AS MENTIONED
ABOVE, GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THE DV CAMCORDER SHALL BIND
CUSA. (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU) CUSA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS,
EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OF DATA, OR ANY OTHER
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE
DV CAMCORDER, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CUSA HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CUSA
BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE DV CAMCORDER SOLD BY CUSA AND CAUSING
THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS,
DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF
USE, MISUSE OR INABILITY TO USE THE DV CAMCORDER NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CUSA.
(SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.) THIS LIMITED WARRANTY SHALL NOT EXTEND TO
ANYONE OTHER THAN THE ORIGINAL PURCHASER OF ANY DV CAMCORDER, OR THE PERSON FOR WHOM IT
WAS PURCHASED AS A GIFT, AND STATES YOUR EXCLUSIVE REMEDY.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Canon U.S.A., Inc.
One Canon Plaza
Lake Success, New York 11042
161
CANADA
CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY
E
The limited warranty set forth below is given by Canon Canada Inc. (“Canon Canada”) with respect to Canon digital video
equipment purchased in Canada. This limited warranty is only effective upon presentation of a bill of sale or other proof of
purchase for this Canon digital video equipment to a Canon Service Facility when repairs are required.
Canon consumer video digital equipment is warranted under normal, non-commercial, personal use, against defective
materials or workmanship as follows:
Parts: Defective parts will be exchanged for new parts or, at Canon Canada’s option, comparable rebuilt parts for a period
of one year from the date of original purchase, except Video Heads which will be exchanged for a period of 3 months from
the date of purchase.
Labour:
For a period of one year from the date of original purchase, labour will be provided free of charge by our
Canon Service Facilities in Canada.
This limited warranty covers all defects except where:
(a) The loss or damage to the product results from:
i) accident, natural disaster, mishandling, abuse, neglect, unauthorized product modification or failure to follow
instructions contained in the instruction manual;
ii) the use of accessories, attachments, products, supplies, parts or devices with this Canon product that do not
conform to Canon specifications or that cause abnormally frequent service problems;
iii) repairs or services performed by any party other than a Canon Service Facility;
iv) defective batteries or any exposure to water, sand or dirt;
v) shipping (claim must be presented to the shipper);
(b) Any serial number on the video equipment is altered or removed.
(c) The digital video equipment is used for commercial, professional or industrial purposes.
This limited warranty does not cover the cabinet (exterior finish) of the digital video equipment, video cassette tapes, head
cleanings, nor does it apply to digital video equipment purchased outside Canada.
TO OBTAIN WARRANTY SERVICE
Ship your Canon digital video equipment in its original carton, box or equivalent, properly packed, fully insured with
shipping charges prepaid, together with a copy of your bill of sale or other proof of purchase and a description of the
problem to any of the Canon Service Facilities in Canada.
LIMITATIONS
Except as otherwise required by applicable legislation, this warranty is in lieu of all other warranties, conditions, guarantees
or representations, express or implied, statutory or otherwise, relative to this Canon product, including implied warranties
or conditions of merchantability or fitness for a particular purpose.
Canon Canada assumes no liability for special, consequential or incidental damages or loss that may arise, whether on
account of negligence or otherwise, from the use, misuse or inability to use this Canon product (including loss of profit,
revenue, video tapes or enjoyment) or from failure to conform to any express or implied warranties, conditions, guarantees
or representations. Any recovery under this limited warranty shall not exceed the purchase price of the product. Canon
Canada does not assume or authorize any other person to assume for Canon Canada any other liability with respect to this
Canon product.
This warranty does not extend to any person other than the original purchaser of this Canon product or the person for
whom it was purchased as a gift and states your exclusive remedy.
NOTICE TO CONSUMER
If you plan to take important videos or if the product has not been used for some time, please check all functions with the
instruction book before using it.
162
CANON INC.
U.S.A.
CANON U.S.A., INC. NEW JERSEY OFFICE
100 Jamesburg Road, Jamesburg, NJ 08831 USA
CANON U.S.A., INC. CHICAGO OFFICE
100 Park Blvd., Itasca, IL 60143 USA
CANON U.S.A., INC. LOS ANGELES OFFICE
15955 Alton Parkway, Irvine, CA 92618 USA
CANON U.S.A., INC. HONOLULU OFFICE
210 Ward Avenue, Suite 200, Honolulu, HI 96814 USA
● If you have any questions, call the Canon U.S.A. Information
Center toll-free at 1-800-828-4040 (U.S.A. only).
CANADA
CANON CANADA INC. NATIONAL HEADQUARTERS
6390 Dixie Road, Mississauga, Ontario L5T 1P7
CANON CANADA INC. CALGARY
2828, 16th Street, N.E. Calgary, Alberta T2E 7K7
CANON CANADA INC. MONTREAL
5990 Côte de Liesse, Quebec H4T 1V7
● If you have any questions, call the Canon Canada Information
Center toll-free at 1-800-828-4040. (Canada only)
● Si vous avez des questions, veuillez téléphoner sans frais au
Canada 1-800-828-4040. (Canada seulement)
MEXICO
CANON MEXICANA, S. DE R.L. DE C.V.
Periferico Sur No. 4124 Col. Ex-Rancho de Anzaldo C.P. 01900
México, D.F., México
CENTRO Y
SURAMÉRICA
CANON LATIN AMERICA, INC.
703 Waterford Way Suite 400 Miami, FL 33126 USA
ASIA
CANON HONGKONG COMPANY LTD.
9/F, The Hong Kong Club Building, 3A Chater Road, Central, Hong Kong
Printed on 100% reused paper.
Document réalisé avec du papier recyclé à 100%.
El papel aqui utilizado es 100% reciclado.
PRINTED IN JAPAN
PUB.DIM-536
0000Ni0.0
© CANON INC. 2003
DY8-9120-373-000
IMPRIME AU JAPON
IMPRESO EN JAPÓN
|
