Chopper (FX350) / Chopper Blender (FX350B)
(with FX350B)
First Use Safety Recommendation
Please read through this booklet for safe and efficient use of the appliance
even if you are familiar with using this appliance.
Keep this guide handy for future reference.
FX350 / FX350B
ENGLISH
Parts Identification
1. Blender lid cap (FX350B)
2. Blender lid (FX350B)
3. Blender jar (FX350B)
4. Blender Blade (FX350B)
5. Cover
10
6
10
2
1
5
6. Chopper Blade
7. Bowl
6
7
8. On / Off switch
9. Motor housing
3
8
9
4
10. Blade release button
FEATURES
•
•
•
•
•
•
700W
Single speed pulse operation
1 litre Blender jug (FX350B only)
Brake
Non-slip feet
Stainless steel blades
-3-
ENGLISH
Before first use:
•
Before using your Chopper Blender for the first time, make sure it is disconnected from the electrical supply,
then remove all packaging.
•
•
•
•
•
•
•
•
•
All parts should be cleaned before use.
Clean all parts as recommended in the section “How to take care of your Chopper/Chopper Blender”
The motor housing (9) must only be cleaned with a damp cloth, and dried thoroughly before use.
To clean the Blender jar (3), add 0.5L of warm water and a little detergent to the jar.
Fit the jar to the Motor housing & connect it to a suitable electrical supply.
Run the Blender for a few seconds until clean.
Rinse, repeat & rinse again.
Dry carefully, taking care when approaching the blades as these are very sharp.
All other parts can be washed using a mid detergent and warm water. These parts are not dishwasher safe
and must be hand washed.
•
•
After washing, rinse and allow all parts to dry thoroughly before re-assembly and storing.
Take care when handling the cutting blades as they are sharp.
How to assemble your Chopper (FX350)
•
•
•
•
Place the motor housing (9) on a flat, stable surface.
Place the bowl (7) over the stem on the motor housing.
Fit the blade (6) over the boss on the bowl. Press down gently to make sure it is locked in place.
Fit the cover (5) over the bowl; rotate anti-clockwise to lock in place.
Note: The chopper will not work unless the cover is correctly fitted.
How to assemble your Blender (FX350B)
•
•
•
•
Place the motor housing (9) on a flat, stable surface.
Place the blender lid (2) on top of the blender jar; rotate anti-clockwise to lock in place.
Fit the blender lid cap (1) into the blender lid & rotate anti-clockwise to lock in place.
Place the Blender jar (3) on the motor housing and rotate it in an anti-clockwise direction until it locks in
place.
Note: The blender will not work unless it is correctly fitted.
How to use your Chopper (FX350)
•
•
•
This appliance is designed to chop dry ingredients such as meat.
Do not use this appliance for any other purpose. For indoor domestic use only.
Prepare the ingredients by cutting them into small cubes and place them in the bowl (7). Do not over-fill the
bowl.
•
•
Fit the cover (5) over the bowl and rotate anti-clockwise to lock in place.
To avoid a hazard, this appliance must only be used for chopping dry ingredients.
Note: The chopper will not work unless the cover is correctly fitted.
Press the on / off switch (8) down.
•
The unit should only be operated for 5 to 15 second pulses only. Never operate the chopper continuously
for longer than 45 seconds at a time. Always allow the appliance to cool down for a minimum of 15 minutes
before next use.
•
•
•
When the correct consistency is achieved, disconnect the unit from the electrical supply.
Remove the cover, the blade and then remove the bowl & transfer the ingredients to a suitable container.
Take care when handling the cutting blades as they are sharp.
-4-
ENGLISH
How to use your Blender (FX350B)
•
Your Black & Decker blender has been designed for the following applications: blending, mixing and
crushing of solid and liquid food and beverage ingredients. This product is intended for household use only.
•
•
Prepare the ingredients and place them in the jar (3). Do not over-fill.
Fit the lid (2) over the bowl and the lid cap (1) to it, rotating both in an anti-clockwise direction to lock them
in place.
•
•
Place the Blender jar (3) on the motor housing and rotate it in an anti-clockwise direction until it locks in
place.
Do not open lid until the blades come to a complete stop.
Note: The blender will not work unless it is correctly fitted.
Press the on / off switch (8) down.
•
The unit should only be operated for 5 to 15 second pulses only. Never operate the chopper continuously
for longer than 45 seconds at a time. Always allow the appliance to cool down for a minimum of 15 minutes
before next use.
•
•
•
•
•
When the correct consistency is achieved, disconnect the unit from the electrical supply.
Remove the jar from the motor housing. Remove the lid & pour the ingredients into a suitable container.
How to take care of your Chopper (FX350) / Chopper Blender (FX350B)
The appliance must be cleaned thoroughly after each use.
Make sure the appliance is switched ‘OFF’ and unplug the unit from the power supply before cleaning.
NOTE: NEVER IMMERSE the motor housing (9) IN WATER OR ANY OTHER LIQUID.
To clean motor housing, wipe clean with a damp cloth. Allow to dry thoroughly before re-using or storing.
To clean the Blender jar, add 0.5L of warm water and a little detergent to the jar.
Fit the jar to the Motor housing & connect it to a suitable electrical supply.
•
•
•
•
•
•
Run the Blender for a few seconds until clean. Rinse, repeat & rinse again.
Dry carefully, taking care when approaching the blades as these are very sharp.
All other parts can be washed using a mid detergent and warm water. These parts are not dishwasher safe
and must be hand washed.
•
•
After washing, rinse and allow all parts to dry thoroughly before re-assembly and storing.
Take care when handling the cutting blades as they are sharp.
Protecting the environment
Separate collection. This product must not be disposed of with normal household waste.
Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to
you, do not dispose it off with other household waste. Make this product available for separate collection.
Separate collection of used products and packaging allows materials to be recycled and used again.
Use of recycled materials helps prevent environmental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of electrical products from the household, at municipal
waste sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have
reached the end of their working life. To take advantage of this service please return your product to any
authorised repair agent who will collect them on our behalf. You can check the location of your nearest
authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual.
A list of authorised Black & Decker repair agents and full details of our after-sales service and contact are
-5-
ENGLISH
BLACK & DECKER HOME APPLIANCE 2 YEAR WARRANTY
Black & Decker provides a 2 Year Warranty for this product from the date of purchase against defects due to
defective materials or workmanship. Motor/element burn-outs due to voltage fluctuations are not covered under
warranty. If the product should become defective within the warranty period, Black & Decker will repair or (at Black &
Decker's discretion) replace it free of charge.
The warranty provisions do not cover failure due to accident, misuse, abuse, negligence or non observation of local
regulations on the part of the user. Equally, the warranty provisions do not apply where the appliance has been
serviced by a person not authorized by Black & Decker or serviced with non-approved parts and this has contributed
to the fault of the product. Superseded models without a replacement equivalent will either be repaired or (at Black &
Decker's discretion) replaced with another product of similar retail value.
UPON PURCHASE
Fill in the Warranty Registration Card with the original Authorized Dealer's stamp (indicating date of purchase) and
attach your purchase receipt to it. Retain in case of claims in the future.
MAKING A CLAIM
Take your defective product together with the Warranty Registration Card & purchase receipt to your local service
Centre. You can either do this in person or send it freight prepaid. If mailing or shipping your appliance, ensure that it
is packed carefully in a sturdy carton with enough packing material to prevent damage. Include a note describing the
problem to the service Centre and be sure to give your return address.
DESIGNED FOR DOMESTIC PURPOSES ONLY.
Names
&
Addresses for Black
&
Decker Service Concessionaries
Afghanistan: Ishan National Co., Opp. Ministry of Justice, Kabul. Tel.: +93-2-2101727. Algeria: SARL Outillage Corporation, 04
Route De Dely Brahim Cheraga, Alger. Tel.: +213-21-364363/508, Fax: +213-21-369667. Bahrain: Fawaz Al Zayani, P.O.Box
26563, Adliya, Manama. Tel.: +973-17-715252/712756, Fax: +973-17-713789. Bangladesh: Ultra Corporation, 8, Kushol Centre,
Uttara, Dhaka 1230. Tel.: +880-2-8919272/9756 Ext.28, Fax: +880-2-9887167. Egypt: Anasia Egypt for Trading S. A. E., P.O.Box
2443, 110 Mostafa Refaat Street, Sheraton Heliopolis 11361, Cairo. Tel.: +20-2-2684159, Fax: +20-2-2684169. Ethiopia: Tewfik
Sherif & Co. Ltd., P.O.Box 5583, Debre Zeit Road, Addis Ababa. Tel.: +251-1-651700/601, Fax: +251-1-650570. India: Gryphon
Impex Pvt. Ltd., D-6/4, Okhla Industrial Area, Phase-I, New Delhi-110020. Tel.: +91-11-26372602-4, Fax: +91-11-26372601. Iran:
Tehran - Service Centre of Iran, No 510, South Karger Ave, Below Pasteur Sq. Tehran. Tel.: +98-21-6490608/0656/6407672. Kish
Island: Cayhan Electric Co., No. 69, Paradise Shopping Centre, Kish Island. Tel.: +98-76444-22894. Jordan: Bashiti Hardware,
P.O.Box 1564, TLA Ali, Amman. Tel.: +962-6-5350009/4770741, Fax: +962-6-5350012/4789783. Kenya: Zylog Enterprises, IPS
Building, Kuanda Street, P.O.Box 40877, Nairobi. Tel.: +254-2-338188/199, Fax: +254-2-330642. Kuwait: Al Omar Technical Co.,
P.O.Box 4062, 13041 Safat, Kuwait. Tel.: +965-4848595/0039, Fax: +965-4845652. Lebanon: Est. F.A. Kettaneh SA, P.O.Box
110242, Dora Highway, Kettaneh Building, Beirut. Tel.: +961-1-255860/6, Fax: +961-1-255891. Libya: El Ghoul Brothers, P.O.Box
348, Islamic Call Bldg., Office 201-202, Benghazi. Tel.: +218-61-9097681/4183, Fax: +218-61-9094123. Madagascar: Group
Tana Confort S. A. R. L., B. P. 1770, Antananarivo. Tel.: +261-20-2264505, Fax: +261-20-2264244. Malta: John G. Cassar Ltd.,
36 Victory Str, Qormi QRM 06, Malta. Tel.: +356-21-493251, Fax: +356-21-483231. Mauritius: Happy World Marketing Ltd., Block
2, Industrial Estate, Coromandel, P.O.Box 429, Port Louis. Tel.: +230-2076700, Fax: +230-2337330/7400. Nepal: Universal
Trading Centre, P.O.Box 1947, Tripureswor, Kathmandu. Tel.: +977-1-262192/260587/785, Fax: 261154. Nigeria: Amin Bros. Eng.
Co. Ltd., 30A (Plot 1291), Akin Adesola Street, Victoria Island, Lagos. Tel.: +234-1-3201778, Fax: +234-1-2613667. Oman: Oman
Mktg. & Service Co., P.O.Box 2734, Ruwi, Muscat. Tel.: +968-560232, Fax: +968-560255. Pakistan: Karachi - Ammar Service &
Spares, 60, Bank Arcade, Serai Road, Karachi. Tel.: +92-21-2426905, Fax: 2427214/5243. Pakistan: Lahore - Electronics Inn,
212-G Raja Centre, Main Market, Gulberg, Lahore. Tel.: +92-42-5756750. Philippines: Modern House International Enterprises,
213 Rizal Ave. Extension, between 2nd and 3rd Ave. Kalookan City. Tel.: +632 366-4487, Fax: +632 366-4489. Qatar: Al Muftah
Trading & Cont., P.O.Box 875, Doha. Tel.: +974-4650880/4446868, Fax: +974-4441415. Saudi Arabia: Dammam - Ebrahim
Fawaz Al Zayani, P.O.Box 76026, Al Raka, Dammam. Tel.: +966-3-8140914, Fax: +966-3-8140824. Jeddah: Anasia - P.O.Box
50959, Jeddah - 21477. Tel.: +966-2-6710014, Fax: +966-2-6725929. EAC (Al Yousuf) - P.O. Box 30377, Jeddah - 21477. Tel.:
+966-2-6519912, Fax: +966-2-6511153. Madina: Garziz Trdg. for Bldg. Mat.&Decor., P.O.Box 3364, Madina. Tel.: +966-4-
8261490/8227636, Fax: +966-4-8265741. Riyadh: Anasia, P.O.Box 18689, Riyadh - 11425. Tel.: +966-1-2693751, Fax: +966-1-
4501178. Yanbu: Bin Afif, P.O.Box 530 Yanbu, Al Bahr. Tel.: +966-4-3222626/8867, Fax: +966-4-3222210. Sri Lanka: Delmege
Gen. Equip. Pvt. Ltd., No. 428/1AT. B., Jaya Mawatha (Darley Road), Colombo-10. Tel.: +94-11-2665914, Fax: +94-11-2665915.
Sudan: United Distribution Company, P.O.Box 325, Sayed Abdul Rehman Street, Khartoum. Tel.: +249-11-772612/777296, Fax:
+249-11-770919. Tanzania: General Motors Investment, P. O Box 16541, 14 Vingunguti Nyerere Road, Dar Es Salaam. Tel.: +255-
22-2862661/5022, Fax: +255-22-2862667/5412/3. Tunisia: STE Tunisienne De Quincaillerie Stq., Nvelle Z.I 2013, Ben Arous,
Tunis, Tunisia, Tel: +216 71386102, Fax: +216 71380412. UAE: Abu Dhabi - Light House Electric., P.O.Box 120, Abu Dhabi. Tel.:
+971-2-6726131, Fax: +971-2-6720667. Dubai - Black & Decker (O) A.G., P.O.Box 5420, Dubai. Tel.: +971-4-7028234/233, Fax:
+971-4-2822765. Ideal Mach. & Equipt. R. W/shop P.O.Box 37116, Al Quoz, Dubai. Tel.: +971-4-3474160, Fax: +971-4-3474157.
Sharjah - McCoy Middle East LLC, P.O.Box 20228, Sharjah. Tel.: +971-6-5336321, Fax: +971-6-5336320. Uganda: The Building
Centre, Kitgum House, 52 Station Road, P.O.Box 7436, Kampala. Tel.: +256-41-234567, Fax: +256-41-236413. Yemen: Aden -
Middle East Trad. Co. Ltd., Mulla Dakka, Aden. Tel.: +967-2-240950, Fax: +967-2-240952. Sana'a: Middle East Trad. Co. Ltd.,
P.O.Box 12363, Hayel Street, Sana'a. Tel.: +967-1-204201, Fax: +967-1-204204. Taiz: Middle East Trad. Co. Ltd., Campa area
near Al-Kair mosque, Taiz. Tel.: +967-4-231610/232033, Fax: +967-4-219869. Zimbabwe: J.D.Distributors, P.O.Box 226, 17
Bessemer Road, Graniteside, Harare Tel.: +263-4-753913-7, Fax: 753918.
WARRANTY REGISTRATION CARD
|