Audison measurement standards
(Power measures taken according to audison standard, 1998 edition)
- 12VDC and 13.8VDC;
- 1 kHz or crossover cut-off frequency;
- 0.3% THD @ nominal power; 1% THD @ continuous power;
- Tolerance: +10%; -5%;
- Continous power given by RMS Voltage measured on resistive load;
- The nominal power of the amplifier is measured upon a battery voltage of 12 Volts with
a 4 Ohm load and with all channels in function.
OWNER’S MANUAL
CAR POWER AMPLIFIER
is a division of
62018 Potenza Picena (MC) Italy
CONTENTS
INSTALLATION
audison cable PRODUCTS FOR ELECTRIC CONNECTIONS
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p.
4
5
In-Out panel
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power supply panel
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
7
Controls panel
Functions and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Setting panel
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Amplifier configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Subsonic filter cut-off frequency modification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
VCA-VCA1D modules insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Technical features
Size for fixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
LRx 5.600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Accessories
VCR01K, VCRAK and VCRDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CLK2 - LRx Cooling Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Configurations
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Configurations table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Controls panel diagram and configuration switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Configuration examples
Front+Rear+Sub (F-R Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Multichannel+Sub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3 Channel Front+Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installation
Logo rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Amplifier fixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Electric connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
audison cable products for electric connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
audison measurement standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
22
3
DESCRIPTION
INSTALLATION
Audison LRx 5.600:
AMPLIFIER FIXING
Five channel car power amplifier characterised by excellent musical performances, small size and
outstanding energy reserve.
Its PWM power supply stage is made with two pairs of 70A MOSFETs; it is stabilised and oversize.
Input stage is provided with a special circuit (LNS) which allows the system disturbances rejection,
reducing noise that is usually due to the vehicle electric parts (alternator, electronic injection, etc.),
without altering musical signal quality.
Driver stages are characterised by a very linear circuitry.They have coupled differential transistors and an
A Class complementary voltage amplifier. Power sections have Darlington configuration with high gain
and SOA (Safety Operation Area) BJT TO247.Thanks to its great capacity to supply current, to the use of a
pair of BJT for every channel and of two pairs for the sub, this amplifier can easily drive even the hardest
loads and satisfy whatever power needs. It can give 60W on Front and Rear channels and 180W on sub
with 4 Ohm load, 85W on Front and Rear channels and 240W on sub at 2 Ohms in continuous mode.
Power increases up to 170Wx2 at 4 Ohms and to 240Wx1 at 2 Ohms in mono configuration (3-Ch).
Differently from what occurs with other amplifiers, LRx 5.600 is not blocked by protection systems
immediately below these load values. Its exclusive “Overload Limiter” circuit allows it to go on working,
limiting output power and pointing out how hard the applied load is by the“Limit”LED blinking.
Its big power reserve, its constant control at low frequencies and its exquisite timbre qualities make it an
ideal amplifier to realise systems designed to attain outstanding musical features and very high sound
pressures (SPL).
LRx 5.600 has a bypass subsonic filter (24dB/Oct.) with adjustable frequency, pre-set at 20Hz, and three
Butterworth crossovers with independent frequencies: HI/LO-PASS (12dB/Oct.), HI-PASS (12dB/Oct.) and
LO-PASS (24dB/Oct.). Constant Bass function is also available; it permits to control the subwoofer level
whatever the head unit Fader adjustment is.
ELECTRIC CONNECTIONS
Four switches under the setting panel in the amplifier bottom allow to choose:
• functioning configuration: Front/Rear and Multichannel;
CAUTION!
For the system safer protection, we
recommend the use of a strip fuse
on the cable that connects the
battery positive pole to the
amplifier POWER (+) terminal block.
This fuse has to be installed about
10 cm far from the battery; its value
will have to be equal or slightly
higher (+10% approx.) than
consumption @13.8 VDC, according
to the different configurations (see
“Technical features”).
• 3/5 channel output;
• the activation of a third input dedicated to subwoofer.
They also permit to configure the preamplified output (OUT) as additional input to accept the source
output for Rear system.
In case LRx amplifiers are used in extremely difficult conditions (very low loads) or in installations where
space is too narrow and their heat sink cooling is not enough, they can be employed together with
CLK2 cooling system (optional). It is a system made of two units to apply onto the amplifier sides; each
of them is provided with an electronically controlled fan that allows the amplifier thermal stabilisation
(see“CLK2 – LRx Cooling Kit”).
Protection includes:
• RGP (Resettable Ground Protection) circuit; in case a short circuit occurs between loudspeakers outputs
and car chassis, it detects a high current flow in the pre-input ground and acts by putting the amplifier in
stand-by, protecting its circuitry;
It will have to be equal to the sum of
the values of all fuses in case system
consists of several amplifiers or in
case amplifiers have several fuses.
• a device against short circuits and against DC in the outputs, to protect loudspeakers.
• a device that detects the amplifier temperature excessive increase and stops its functioning until
optimal conditions occur again.
Once the causes which implied protection circuits intervention have been checked and solved, the
amplifier is reset by switching it off and on again.
The amplifier is also provided with another general protection which is insured by an internal strip fuse,
very easy to reach.
Optional:
LRx 5.600 FUSE: 50A
The following devices are available upon request:
1 – Three kits for subwoofer volume remote control:
• VCR01 and VCRAK (analogue and specific for subwoofer);
• VCRDK (digital; it can be used for master volume control or for level control of any ways in a
multichannel system).
2 - CLK2 cooling system.
4
21
IN-OUT PANEL
INSTALLATION
LOGO ROTATION
FUNCTIONS
1 - Remove the transparent
cover which protects
controls and then the 4
screws which block the
metal plate by using
multispanner.
1
FRONT-WF/REAR-TW/SUB
Power outputs of the amplifier Front, Rear and Sub channels. Connect
the speakers cables to these outputs according to polarity. Terminal
blocks accept cables up to 9 A.W.G. max (see “audison cable products
for electric connections” as far as their size is concerned). We
recommend the use of audison cable products.
Please use FRONT-WF channels +L and –R terminal blocks called mono
for the right channel (R) and REAR-TW channels +L and –R terminal
blocks for the left channel (L) in order to connect the amplifier in mono
(3 Ch.) and to exploit the maximum power insured by this configuration.
2 - Remove the plate without damaging the
silkscreen printed panel which will have to
stay on. We suggest that you seize both plate
grips with your hands and pull them by
blocking the silkscreen printed panel with
your fingers against the amplifier chassis at
the same time. This will permit to remove the
plate from the panel without damages.
2
POWER
PPS (Phantom Power Supply)
Power supply socket for audison external
audio accessories.
IN OUT
OTE
FUSE
2
5
3
3 - Remove the strip with
audison logo.
1
1
4
3
IN FRONT / 3 Ch-mono
Left (L) and right (R) channels inputs of the amplifier Front system. Front preamplified outputs of a source (head unit, CD
player, DAT, etc.) or of an external electronic crossover must be connected to them. In three channel configuration (3 ch),
the right channel (R) drives Front outputs in mono, while the left channel (L) drives Rear ones in mono. The subwoofer
can be driven by these two inputs together; if the source has the necessary, special output, it can be driven through In Sub
input, to select through the proper switch.
4 - Put the strip back again after turning it, so
that audison logo is upside down.
4
IN REAR/OUT
Left (L) and right (R) channels inputs of the amplifier REAR system. Rear preamplified outputs of a source (head unit, CD
player, DAT, etc.) or of an external electronic crossover must be connected to them. These inputs can also be configured
as amplifier HI-PASS preamplified outputs (see“Configurations table”).
5 - Mount the plate
back by fixing it
through the screws;
then, re-assemble the
transparent cover
which protects
5
IN SUB
controls.
Left (L) and right (R) channels inputs. They accept the possible subwoofer preamplified output coming from the source.
Since subwoofer output is mono, the two inputs are to be mixed when used together.
5
20
POWER SUPPLY PANEL
CONFIGURATION EXAMPLES
FUNCTIONS
3 CHANNEL FRONT+REAR
Pre Out
1
REMOTE IN
Front
Rear
Terminal to connect Remote cable, which comes from the
source and which controls the amplifier switching on. Applied
voltage must be between 7 and 15VDC.
2
POWER
IN OUT
REMOTE
3
1
FUSE
LRx 2
Config. 3
4
5
2
REMOTE OUT
Terminal to repeat the switching on control (Remote IN) coming from the source. It is used to
switch on another amplifier or device in the system simultaneously. Available voltage is the same
as the one applied on Remote IN.
+
+
3
VCR (optional kit)
Terminals to connect VCR01/VCRA/VCRD adjuster included in sub output volume remote control
kits (VCR01K/VCRAK/VCRDK).
LRx 5.600
Config. 3
Tweeter
Woofer
Tweeter
4
Woofer
FUSE (50A)
Rear
Strip fuse. It insures the amplifier general protection. In case the fuse breaks down, please replace
it by respecting its original value.
CAUTION: If you want to protect the system even more, please put a strip fuse onto the cable
which connects the battery positive pole to the amplifier POWER (+) terminal block (see “Electric
connections”).
+
+
+
Subwoofer
5
POWER
Terminal blocks for the amplifier power supply cable connection. Connect positive and
negative poles according to indicated polarities. Holes have 8mm diameter and accept cables
up to 3 A.W.G. max. In order to get the best current transfer, please use power supply cables
with as big a section as possible. audison cable catalogue offers you a complete range of such
products which can satisfy whatever demands; you can also find Maincrimp terminals in it. We
strongly recommend their use because they contain the cable non protected end and allow the
terminal block to fasten all its useful section.
Tweeter
Tweeter
Woofer
Woofer
Front L
Front R
6
19
CONFIGURATION EXAMPLES
POWER SUPPLY PANEL
FRONT+REAR+SUB (F-R MODE)
FUSE REPLACEMENT
Pre Out
Rear
Front
Sbu
LRx 5.600
Config. 2
1 - Open the transparent cover by pushing the two teeth in
its lowest corners to the direction indicated by the arrows.
+
+
+
+
+
Subwoofer
Tweeter
Woofer
Tweeter
Woofer
Tweeter
2 - Remove the screws which fasten the fuse to eliminate
pieces of the broken one; prevent them from going into the
device.
Woofer
Rear L
Rear R
Woofer
Tweeter
Front R
Front L
MULTICHANNEL+SUB
Pre Out
Front
3 - Check the value of the new fuse to assemble, then fix it by
LRx 5.600
Config. 4
gradually and alternately fastening the two screws. This will
avoid voltage drops along the line and will make the device
perfect functioning easier.
+
+
+
+
Woofer
Woofer
Midrange
Midrange
Tweeter
Tweeter
+
4 - Close the transparent cover.
Front L
Front R
Subwoofer
18
7
CONTROLS PANEL
CONFIGURATIONS
FUNCTIONS AND CONTROLS
CONFIGURATIONS TABLE
LRx 5.600 can be configured as follows:
1
Config. 1 = 5 Ch.: Front (Hi 12dB) + Rear (Hi 12dB) + Sub (Lo 24dB); IN Front (1 IN); Input Sub (IN Sub/IN Front)
Config. 2 = 5 Ch.: Front (Hi 12 dB) + Rear (Hi 12dB) + Sub (Lo 24dB); IN Front/Rear (2 IN); Input Sub (IN Sub/IN
Front + Rear)
LIMIT (orange LED)
It indicates the Overload Limiter circuit is on.
Caution:
When this led is on (although sporadically), it means the applied load is a hard one. The activation
of Overload Limiter circuit (output power limiter) will anyway allow the amplifier to function
without distortions. In case Overload Limiter gets on too frequently (at every power peak), you will
need to check if there are any failures or a too hard load (that’s to say impedance is about 50%
lower than the minimum recommended one). The amplifier can go on functioning in these
conditions but power will inevitably decrease.
Config. 3 = 3 Ch.:Front L + R (Hi 12dB) + Sub (Lo 24dB); IN Front (1 IN); Input Sub (IN Sub/IN Front + Rear)
Config. 4 = 5 Ch. Multichannel:Woofer (Hi/Lo 12dB) + Tweeter (Hi 12dB) + Sub (Lo 24dB); IN Front (1 IN); Pre
Out:(Hi 12dB)
Config. 5 = 3 Ch. Multichannel:Woofer L + R (Hi/Lo 12dB) + Sub (Lo 24dB); IN Front (1 IN); Pre Out:(Hi 12dB)
IN-REAR
PRE-OUT
MIXED SUB*
IN-SUB
CONFIG.
FRONT/WF
REAR/TWEETER
SUB
24dB
IN-SELECT
1 IN
MODE
FR
CH SELECT
5 CH
PRE IN
FR SUB
*
MC
MC
MC
MC
MC
12dB
12dB
NOT USED
1IN/SUB
1
F2
F3
F1
F1
F1
F1
F1
2 IN
FR SUB
*
FR
FR
FR
FR
5 CH
3 CH
12dB
12dB
IN REAR
2IN/SUB
1IN/SUB
1IN/SUB
1IN/SUB
2
3
4
5
F2
F3
24dB
24dB
24dB
24dB
BRIDGED
BRIDGED
12dB
FR SUB
*
1
12dB
NOT USED
F2 (RIGHT)
F2 (LEFT)
NOT USED
1 IN
FR SUB
*
5 CH
12dB
12dB
12dB
F3
F3
F2
BRIDGED
F4
F4
2
11
BRIDGED
12dB
1 IN
FR SUB
*
3 CH
12dB
12dB
F2 (RIGHT) F4
F2 (LEFT) F4
*
MIXED SUB (F+R)/IN SUB switch can be set as follows:
- MIXED SUB (F+R): sub is driven by Front and Rear signals together
- IN SUB: sub is driven by the special input.
CONTROLS PANEL DIAGRAM AND CONFIGURATION SWITCHES
3
10
9
8
7
4
5
6
2
ON (green LED)
It indicates the amplifier is on.
8
17
CONTROLS PANEL
CONFIGURATIONS
BLOCK DIAGRAM
3
7
F1
SUBSONIC
It permits to adjust the subwoofer
24dB/Oct. LO-PASS filter cut-off frequency
between 40 Hz and 150 Hz.
S U B
F R O N T
R E A R
R E A R
F R O N T
It permits to eliminate subsonic
frequencies; these sounds cannot be
heard by human ears but cause useless
and damaging stress to amplifier and
speakers.
Subsonic filter can be bypassed
(BYPASS) and it is pre-set at 20 Hz. Its
cut-off frequency can be adjusted
between 16 and 32 Hz through 4 Hz
steps; this occurs by replacing the special
resistors located into a socket which can
be reached through the setting panel in
the amplifier bottom.
8
F3
It permits to adjust the Rear system
12dB/Oct. HI-PASS filter cut-off frequency
between 40 Hz and 150 Hz. It works only in
Front-Rear configuration.
9
F4
4
It permits to adjust the woofer 12dB/Oct.
LO-PASS filter and the Mid-Tweeter
12dB/Oct. HI-PASS filter crossover
frequencies between 150 Hz and 5 kHz. It
works only in Multichannel configuration.
SUB (Level)
It adjusts the amplifier Sub channel input
sensitivity and sets its output level.
5
10
F2
REAR M-TW (Level)
It permits to adjust the 12dB/Oct. HI-PASS
filter cut-off frequency between 40 and
150 Hz; this filter is for woofer in
Multichannel configurations and for Front
system in Front-Rear configurations.
It adjusts the amplifier Rear channels input
sensitivity and sets its output level.
In multichannel configuration, the
adjustment concerns the channels for the
high frequencies HI-PASS filter (M-Tw).
11
SAFETY (red LED)
6
It indicates that the amplifier protection
circuits are on. In order for the amplifier to
work again, you need to switch the system
off and then on after 10 seconds at least.
We recommend to check all connections
before switching the amplifier on again.
If LED stays on, please contact Audison
authorised after sale centres.
FRONT WF (Level)
It adjusts the amplifier Front channels input
sensitivity and sets its output level.
In multichannel configuration, the
adjustment concerns the channels for the
woofer BAND-PASS filter (Wf).
9
16
SETTING PANEL
ACCESSORIES
FUNCTIONS
Installation:
It permits to reach the switches for the amplifier configuration, the resistors to set subsonic filter cut-off
frequency and to insert VCA modules for the subwoofer volume remote control.
Setting panel
Remote
1 - Remove the setting panel in the
amplifier bottom in order to carry out
operations.
First fan
Second fan
2 - Once operations have
been carried out, please
close the setting panel.
AMPLIFIER CONFIGURATION
Remote
IN
Remote
OUT
LRx 5.600 is configured through IN SELECT, Ch. SELECT, MODE and IN SUB/MIXED SUB (F+R) switches,
located under the setting panel.
+
POWER
• IN SELECT (1 IN – 2 IN)
It permits to use OUT preamplified output as additional input for the head unit Rear preamplified
output, if available (2 IN).This configuration also activates Constant Bass function.
If this switch is on 1 IN, you will be able to make a Front+Rear+Sub system by using only the Front input.
• Ch. SELECT (5 Ch. – 3 Ch. mono)
It configures the amplifier output as 3 or 5 channels. If switch is on 5 Ch., you will be able to make a
Front+Rear+Sub system; if it is on 3 Ch. mono, you will be able to have a Front+Sub system.
• MODE
It permits to choose the amplifier functioning configuration between
Front-Rear and Multichannel. If switch is on Front-Rear, Hi-Pass filters for
Front (F2) and Rear (F3) system are activated. If it is on Multich., Hi-Pass
filters for Woofer (F2) and for Woofer/Mid-Tweeter (F4) are activated.
• IN SUB/MIXED SUB (F+R)
+
Ground
Battery
It activates IN SUB input to accept the source third preamplified output
for subwoofer (IN SUB).
12 V
In case source doesn’t have it, it is possible to drive the subwoofer by
taking the necessary signal from IN Front and IN Rear inputs (MIXED SUB
F+R).
10
15
ACCESSORIES
SETTING PANEL
CLK2 - LRx Cooling Kit
SUBSONIC FILTER CUT-OFF FREQUENCY MODIFICATION
Subsonic filter is pre-adjusted at 20 Hz. In order to modify this value, please act according to what
follows.
This cooling system is specially designed to provide LRx amplifiers with the right working
temperature.
CLK2 should be used when LRx amplifiers work in extremely hard conditions (very low loads) or in
installations where space is too narrow and heat sink cooling is not enough. It consists of two units to
apply onto the amplifier sides; each of them is provided with an electronically controlled fan. Its
intervention depends on a thermal sensor that starts the system as soon as LRx heat sink reaches
45°C. The same sensor is connected to a special circuit which controls the two fans speed progressive
increase when temperature increases, too.
Procedure:
Air flux constant control allows the amplifier very good thermal stabilization and limits noise.
S1
C1
SW1
S2
C1
Replace FS1, FS2, FS3, FS4 resistors according to
the values in the setting panel table.
Remark: Cut the new resistors
rheophores according to the
size in the picture.
10 mm
VCA-VCA1D MODULES INSERTION
LRx 5.600 can accept one of the three optional kits which allow the subwoofer volume remote control:
VCR01K,VCRAK or VCRDK.
These kits have a specific module,VCA or VCA1D, to insert into the amplifier through the setting panel.
Installation:
1 - Remove BYP12 bridge.
2 - Insert VCA/VCA1D module.
- Insertion key. It prevents the module from
being inserted in the wrong way.
14
11
ACCESSORIES
TECHNICAL FEATURES
VCR01K,VCRAK and VCRDK
SIZE FOR FIXING
LRx 5.600 can accept one of the optional kits that allow the subwoofer volume remote control.
VCR01K and VCRAK are analogue and special for sub; VCRDK is digital and can be used for master
volume control or for level control of any ways in a multichannel system.
These kits are available as accessories and consist of three elements:
1) Volume adjuster (VCR01/VCRA/VCRD);
445 mm
412 mm
2) VCA/VCA1D module to put inside the amplifiers;
3) Wire to connect VCR01/VCRA/VCRD adjusters to the proper sockets in the amplifier rear panel
and to the car lights switch, in order to light it up.
Install VCR01/VCRA/VCRD adjusters in a place you can easily and comfortably reach, according to
the following connection diagram.
POWER
IN OUT
REMOTE
Drilling dimensions for fixing
*
FUSE
Remote Out
LRx 5.600
Yellow/White
Yellow/White
POWER SUPPLY
Output power (RMS) @ 13.8 VDC;THD 1%
Blue
Voltage:. . . . . . . . . . . . . . . . . . . . . . . . . . . 11 ÷ 15 VDC
Idling current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 A
Idling current when off: . . . . . . . . . . . . . . . 0.02 mA
- A config.: 60W x 4 (4 Ohms) + 180W x 1 (4 Ohms)
- B config.: 85W x 4 (2 Ohms) + 240W x 1 (2 Ohms)
- C config.(3 Ch.): 170W x 2 (4 Ohms) + 240W x 1 (2 Ohms)
VCR 01
0
FILTERS/INPUTS
Consumption @ 13.8 VDC
(Max Musical Power):
- A config. (see Output Power): . . . . . . . . . . . . 33 A
- B/C config. (see Output Power):. . . . . . . . . 48.9 A
Front-Rear/Front 3 Ch.:
12dB/Oct. Hi-Pass (40 ÷ 150 Hz)
Multichannel:
Control
min
max
- Woofer:
12dB/Oct. Band-Pass
VCR01
VCRD/VCRA
(40 ÷ 150 Hz/150 ÷ 5000 Hz)
- Mid/Tweeter: 12dB/Oct. Hi-Pass (150 ÷ 5000 Hz)
SUB (IN F-R: Constant Bass):
AMPLIFIER STAGE
Black
Black
Red
Distortion – THD (1kHz): . . . . . . . . . . . . . . . 0.009 %
Bandwidth (-3dB): . . . . . . . . . . . . . . . . 4 Hz ÷ 85 kHz
S/N ratio(A weighed @ 1V): . . . . . . . . . . . . . . 105 dB
Damping factor (1 kHz, 4 Ohms): . . . . . . . . . . . 240
Input sensitivity: . . . . . . . . . . . . . . . . . . 0.2 ÷ 5 VRMS
Input impedance: . . . . . . . . . . . . . . . . . . . . 15kOhms
FUSE
(250mA)
Ground
FUSE
24dB/Oct. Lo-Pass (40 ÷ 150 Hz)
Bypass/ 24dB/Oct. Hi-Pass, 16÷32 Hz
(pre-set at 20 Hz)
Red
Subsonic:
(250mA)
Orange
Pre Out (IN Front): 12dB/Oct. Hi-Pass (40 ÷ 150 Hz)
Inputs: . . . . . . . IN Front - IN Rear (Pre Out) - IN Sub
OTHER FUNCTIONS
Lights
switch
Load impedance:
Remote IN: . . . . . . . . . . . . . . . . . . 7 ÷ 15 VDC – 1 mA
Remote OUT:. . . . . . . . . . . . . . . . . . . 12 VDC – 10 mA
Auxiliary power supply (PPS):. 12 VDC – 300 mA
INVCR (SUB volume)VCA/VCA1D attenuation: 100 dB
Fuse: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 A
- Front/Rear (4 Ch. stereo): . . . . . . . . . . . . 4-2 Ohms
- Front/Rear (2 Ch. mono in bridge): . . . . 4 Ohms
- Sub: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 – 2 Ohms
Ground
+
-
Nominal output power (RMS)
NP @ 12VDC;THD 0.3%: . . . . . . . . . . . . . . . . . . . . . . .
60W x 4 (4 Ohms) + 180W x 1 (4 Ohms)
Battery
MAX SIZE (L x H x D):
WEIGHT: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9 kg
176 x 56 x 445 mm
12
13
|