®
ELECTRONICS CORP.
VOH701
7" Drop Down Video Monitor
Installation Guide
MATERIALS INCLUDED IN THIS PACKAGE:
1) VOH701 Video Monitor (1 pc)
2) Accessory Harness (P/N 8010730) (1 pc)
3) 2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc)
4) A/VAdapter Cable (112B3227)
5) Hardware Package
#4 x 3/8” Screws (5 pcs)
#8 x 5/8” Self Drilling Screws (4 pcs)
#8 Washers (4 pcs)
6) Dome Light Harness (1 pc)
1
2
3
5
4
6
TOOLS REQUIRED:
#2 Phillips Screwdriver
#1 Phillips Screwdriver
Utility or Razor Knife or Shears
Wire Strippers
Upholstery hook tool (for removal of panels as necessary)
Electrical Tape
MaskingTape
Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe)
Marker pen – to mark headliner
Scribe (to mark trim ring if used)
Misc. electrical connectors (to connect to vehicle power source). Requirements will vary from vehicle to
vehicle)
Video tape (to verify system operation after installation)
-1-
GENERAL INSTALLATION APPROACH:
1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP,
Tuner, RF Modulator/external amp, remote headphones, 2nd VCP, etc.).
2) Review all manuals to become familiar with electrical requirements and hook ups.
3) Decide upon mounting locations of all components and method of mounting.
4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as
all areas where interconnecting wire harnesses will need to be located. If any access holes need to
be cut into the vehicle (headliner, other trim components etc.), this should be done now as well.
(Refer to Page 3).
5) Route the wiring harnesses throughout the vehicle as necessary. (Refer to the Wiring Diagrams on
page 6 of this manual as well as the wiring instructions for the individual components and accessory
options being installed). Be sure that all wiring is protected from sharp edges and is routed in such a
manner that it will not be pinched when all components and interior trim are fully installed. Be sure to
leave enough slack in the wiring at each component to allow working room.
6) Remove all A/V system components from their packaging and place them loosely in the vehicle at
their respective locations.
7) Connect all components together (electrically) and verify proper operation of all system functions.
Note: This is best done BEFORE, components have been permanently mounted.
8) After verifying proper operation of the system, proceed to mount of each component.
9) When all components are mounted, recheck function of entire system again to ensure that no wiring
was pinched or connected improperly during final installation.
GENERAL SYSTEM CONFIGURATIONS:
The following is intended to give a rough guideline of system configurations that are possible with the
VOH701 Drop Down Video Systems :
System 1: Video Monitor VOH701, VCP.
-All wiring necessary is included with this package.
-Headphones are connected into the headphone jacks on the monitor itself.
System 2: Video Monitor (VOH701), VCP, 2nd VCP (or other A/V component)
-Same as system 1 but extra Source Component (PN 8010730) Harness must be
purchased.
System 3: Video Monitor/TV (VOH701), VCP, 2nd VCP (or other A/V component)
-Same as system 3, but TV antenna must be added (AN-300 or similar).
Notes :
-All systems have built-in game/camcorder inputs (the A/V input jacks on the video monitor itself).
-There are a few audio output options that can be added as follows :
a) Remote headphone jacks can be added to a VOH701 system. Refer to the wiring
diagram on page 6.
-The VOH701 video systems are only intended for an overhead, drop down installation. It is not intended
for seat back or any other type of mounting. The hinging mechanism is designed for horizontal, drop
down use only.
-2-
VEHICLE PREPARATION:
1)
Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when
key is off). Find a suitable location that will provide a good ground. Generally, these wires can be
found at the ignition switch or fuse-box.
2)
3)
The mounting method and location will vary from vehicle to vehicle, so this manual will only focus
on the installation of the video monitor and related console accessories.
Generally, the best location for the video monitor is where the vehicle's factory dome light is in-
stalled. The monitor should be located in such a manner that it can be comfortably viewed by rear
seat passengers. NEVER INSTALL THE MONITOR IN A PLACE WITHIN THE DRIVER'S VIEW.
THIS IS NOT ONLY DANGEROUS, BUT IT ISALSO ILLEGAL IN MANY STATES.
Once the mounting location of the monitor has been determined, there may be additional prepara-
tion work necessary, depending on the vehicle structure and installation method. Some of the
steps that may be required are:
4)
A) Removal of the vehicle's dome light
B) The headliner may need to be trimmed as per the drawing below.
C) If the mini-console (P/N 1181300) will be used, it will have to be trimmed to fit the
contour of the vehicle's headliner. Refer to the "Mini-Console installation" section late in
this manual.
Note :
If your installation will require you to cut out the headliner, the box that this kit came in can be used as a
template. You can remove the shelf that the video monitor rests on and trace the opening onto the
.
FULLSIZE CONSOLE INSTALLATION
There are several "full size" custom consoles available for selected vehicles. Some of these
vehicles are the Chevrolet Suburban, Ford Expedition, and Dodge Durango. These full size consoles
incorporate several additional features, and are particularly useful if the vehicle you are installing this
system into already has an OEM overhead console in the headliner. Refer to the installation manual that
comes with the console itself for complete installation instructions.
-3-
MINI CONSOLE INSTALLATION:
This page only covers special installation considerations for the mini-console installation. If the video
monitor is to be installed with a custom full sized overhead console, refer to page 3.
If the video monitor is to be installed in a vehicle with the mini console (P/N 1181300), this console may
need to be trimmed to fit the contour of the vehicle headliner.
1)
In this installation, the video monitor is mounted directly to the overhead cross-member in the roof
using the mounting screw bosses. These screw bosses should contact the cross-member di-
rectly (i.e.: no gap between the screw boss and the roof structure). Also, be sure that the screws
do not pierce the outer roof skin when fully fastened to the cross-member. The mini-console is
attached to the video monitor using the perimeter screw bosses. It is important that the screws
used in this installation are not overtightened, and that the video monitor and mini-console are
mounted in such a way that the assembly does not distort (or bend) when the mounting screws
are tightened. An alternate method is to use a piece of plywood (5"x9"x3/4"). First secure the
plywood block to the cross-member, then screw the monitor into the plywood. See the drawing on
page 5.
2)
3)
It is best to mount the video monitor to the roof structure without the mini-console first. There
should be a gap between the headliner and the outer flange of the video monitor. The mini-console
should be cut to full this gap. Apply masking tape to the outer surface of the mini-console in the
areas where the cut will be made.
Mark the cut to follow the necessary contour of the roof. The suggested method of marking is as
follows:
A)
First mark the narrowest point of the mini-console on the masking tape. Be careful
to consider not only vertical location, but fore-aft location.
B)
Using the handle of a screwdriver, make a “transfer marking tool”. See diagram
below. Place the tool against the roof and the marker against the masking tape on
the mini-console. Trace the cut to be made around the entire perimeter of the mini-
console.
C)
D)
Cut the mini-console using a sharp utility knife or shears. Make the cut in several
passes over the marked line, each time cutting a little deeper. It is not necessary to
cut completely through the plastic, the cut only need be over 50% of the wall thick-
ness of the plastic. By bending the cut back and forth several times, the plastic will
break cleanly at the cut.
Check the fit of the trimmed console and make any minor adjustments necessary.
4)
5)
The mini-console can be painted or covered with a material that matches the headliner before
assembling the mini-console to video monitor.
The finished mini-console should be attached to the video monitor, then attach the assembly to the
roof.
Headliner
C
Cut line
Lowest point mark
Tivt
Tape marker to screwdriver. Starting at your mark
for the lowest point, trace the contour of the roof
-4-
MOUNTING THE MINI-CONSOLE
Roof
Roof Support
Headliner
5"x9"x3/4" Plywood
Block or Optional
VOHBKT
(4) #8x1" self drilling
screws (not supplied)
Mini-Console
Video Unit
(4) #8 flat washers
(not supplied)
(4) #8x3/4" self tapping
screws (not supplied)
-5-
VOH701
Note: cables
exiting the pod
should be routed
as shown.
Mini-Din Connectors
Dome Light
Item #6
1
2
Power Harness
Item # 3
Red: +12 VDC
(Accessory Cir.)
Black: Ground
Optional Hard Wired FM Modulator Output
RCA-Female
12 VDC Power and Ground
Left
Input
Am/Fm
Antenna
LEFT
FM
WHITE
TO
FACTORY
RADIO
Patch Cord
Modulator
1070610
*Refer to Instructions with the RF
Modulator Kit for further details.
RIGHT
RED
RCA Male to Male
Accessory Harness
Item#2
Right
Input
Dash Radio
RCA-Female
Red RCA (Audio Right)
White RCA (Audio Left)
Yellow RCA (Video)
Power Connector
4 Pin
"Y" Adapter
for use with
Non-Stereo
Installations
Item# 5
IR LED:
Clean the IR Receiver Window on the front of the VCP.
Remove Adhesive Backing and Apply IR LED to IR
Window on the Face of the VCP.
1) Make the connections to the vehicle for the 2 pin wiring harness.
2) Insert the Circular Mini-Din Connector of the source component harness through the wire tie loop on
the main PCB and into the Mini-Din Connector on the main PCB.
3) Pull the wire tie loop tight and cut off the excess.
4) Connect the wired RF Modulator and / or the remote headphone jacks to the video monitor if those
options are being included.
5) Connect power harness to vehicle’s electrical system by tapping into an accessory hot line and a
good ground.
6) Verify all functions of the System before final mounting of the finished assembly.
Note: A second VCP or other A/V Component can be connected to the video monitor system using a
second source component harness (purchased separately, part number: 8010730). This second har-
ness would plug into the second Mini-Din connector on the main PCB as in steps 2 and 3 above.
A/V Source Definitions:
1= VCP (Right Mini-Din on main PCB)
2= 2nd VCP (or game or DVD, etc.…. left Mini-Din)
3= AUX-INPUT (RCA jacks on the face of the monitor).
-6-
CONNECTING THE DOME LIGHTS
The dome lights in the video monitor require three connections to the vehicle's wiring. There are two
common types of dome light circuits used, positive or negative switched. Positive systems supply volt-
age to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs.
To determine which system you have you must locate the wires at the dome light. On a positive switched
system, with all the doors closed and the lights out, both wires at the dome light will rest at ground. When
the light is activated, one of these wires will switch to +12 vdc. This is the vehicle's switching wire. On a
negative switched system, with all the doors closed and the lights out, both wires at the dome light will
rest at + 12vdc. When the light is activated, one of these wires will switch to ground. This is the switching
wire.
For positive systems, connect the purple / brown (Lamp auto) wire to the vehicle's switched wire. Then
connect the red / black (lamp on) wire to a fused constant 12 volt source and the black / red (lamp
common) wire to a good ground. Positive systems are commonly found on Ford vehicles.
For negative systems, connect the purple / brown (Lamp auto) wire to the vehicle's switched wire. Then
connect the red / black (lamp on) wire to a good ground and the black / red (lamp common) wire to fused
constant 12 volt source. Negative systems are commonly found on General Motors and import vehicles.
Note:
Some vehicles which incorporate transistorized control of the dome light circuit, such as the 1999 Dodge
Caravan, may require that the purple / brown (Lamp auto) wire be connected to the door pin switch wire,
as the additional current draw of the Monitor's lights may not be supported by the output of the vehicles
body control computer.
Positive Switched Dome lighting
To
constant
+12vdc
Red / black - Lamp on
To 12 pin
Black / red - Lamp common
connector
Purple / brown - Lamp Auto
on Monitor
Factory Dome light circuit
To
constant
+12vdc
Factory Door ajar
switch or Body
Control computer
-7-
Negative Switched Dome lighting
Red / black - Lamp on
To 12 pin
connector
Black / red - Lamp common
Purple / brown - Lamp Auto
To
constant
Factory Dome light circuit
To
constant
Factory Door ajar
switch or Body
Troubleshooting:
SYMPTOM:
REMEDY:
No power at Video Monitor
-Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor.
Verify ground connection with continuity test from known good ground to
black wire at 2 pin Power Harness
Power but no video or
sound
-Verify that the correct source is selected (i.e.: 1,2,3 or 4). Verify that the
source is on and playing a known good media (such as a videotape). Verify
connections at both ends of the source component harness.
Picture, but no sound
-Push and hold the volume up button until sound is heard over headphones.
If problem is limited to the dash radio, verify radio is tuned to the correct
channel, and that power to the wired RF modulator is on. (Refer to instruc-
tions with modulator kit). Otherwise, verify all connections per the wiring
diagram on page 6.
No Infrared remote func-
tions for VCP (or other com-
ponents)
-Check batteries in the hand held remote (not included with this kit). Verify
that the IR LED ( page 6 Wiring Diagram) is property attached to the sen-
sor window of the VCP (or other component).
-8-
NOTES
-9-
For Customer Service
Visit Our Website At
WWW.audiovox.com
Product Information, Photos,
FAQ’s Owner’s Manuals
128-6882
© Copyright 2003 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788
|