Ameristep RAPTOR TRIPOD 7700 User Manual

RAPTOR  
TRIPOD  
Instruction and Safety Manual  
Model #7700  
Thank You! for purchasing Ameristep®  
Non-Typical RAPTOR TRIPOD  
! CAUTION:  
Maximum Tested Weight Capacity Limit for this Product is: 300 POUNDS  
(Including Accessories, Gear and Attire) DO NOT Exceed tested weight limit capacity.  
!
This product is designed for only ONE PERSON.  
! WARNING: Every year serious injury and even death occurs from hunting related falls. To ensure your safety, please COMPLETELY read  
and follow this safety manual and ALL warning labels BEFORE assembling, installing, or utilizing this product.  
DO NOT USE THIS AMERISTEP® PRODUCT BEFORE FULLY UNDERSTANDING ALL SAFETY WARNINGS AND INSTRUCTIONS. IF YOU HAVE  
QUESTIONS, ARE UNSURE ABOUT ANY INFORMATION, or NEED ADDITIONAL INFORMATION CONCERNING THIS PRODUCT, CONTACT OUR  
CUSTOMER SERVICE DEPARTMENT. KEEP AND MAINTAIN THIS SAFETY & INSTRUCTION MANUAL FOR FUTURE REFERENCE.  
©2008 (rev 6/08)  
SAFETY MUST BE YOUR FIRST PRIORITY WITH THIS PRODUCT  
TREE/LADDER STAND SAFETY INSTRUCTIONS/WARNINGS  
®
Ameristep Tree/Ladder Stands are designed with your safety being our primary concern. We have invested time to properly design, engineer,  
manufacture, and test this product’s safety. This Tree/Ladder Stand will continuously be safe with appropriate equipment, usage and  
®
®
maintenance followed carefully in this safety and instruction booklet. Ameristep and Ameristep Retailers will not be responsible for any  
misuse of this product.  
• ALWAYS inspect tripod before each use and do not store outdoors when not in use.  
• ALWAYS check legs and ladder section connections every time you use tripod.  
• ALWAYS check ground under tripod to ensure it is firm and level.  
• ALWAYS maintain three points of contact when climbing ladder and ALWAYS lean forward as you climb.  
PROPER CARE AND MAINTENANCE:  
• ALWAYS inspect for defects from damage, rot, corrosion, cracks caused from freezing or excessive heat.  
• DO NOT use is damage is detected or suspected.  
• ALWAYS insure the appropriate maintenance such as retightening, or replacement of parts, preserving or refinishing wood, touch-up  
painting and lubrication is recommended.  
• DO NOT leave your Tree/Ladder Stand outside OR in a tree for more than two weeks at a time. Store inside when not in use.  
! CAUTION:  
Maximum Tested Weight Capacity Limit for this Product is: 300 POUNDS  
(Including Accessories, Gear and Attire) DO NOT Exceed tested weight limit capacity.  
This product is designed for only ONE PERSON.  
Never remove any safety warning stickers from this product.  
Safety must be your first priority during the use of this product.  
xxxx  
©2008 (rev 6/08)  
Page 3  
Ameristep® Inc.  
901 Tacoma Ct. • P.O. Box 189 • Clio, MI 48420  
(810) 686-4035  
HARDWARE AND PARTS  
THE  
RAPTOR TRIPOD  
Model #7700  
(1) Shooting Rail  
Connection  
(1) Top Ladder Section  
(1) Left Platform  
(1) Right Platform  
(1) Shooting Rail  
(1) Middle Ladder Section  
(1) Footrest  
(1) Bottom Ladder Section  
(1) Seat Frame  
(2) Bottom Leg  
(2) Middle Leg  
(1) Back Rest  
(2) Top Leg  
(1) M8 x 30mm HEX BOLT  
(2 Washers, 1 Lock-Nut)  
(1) Stabilizer Bar  
(1) Seat Frame Base  
(2) M8 x 40mm HEX BOLT  
(3 Washers, 1 Lock-Nut)  
(3 Parts) BackPack Straps  
(1) 5½” Swivel Washer  
(1) Shooting Rest Pad  
(1) Sling  
(2) M8 x 45mm HEX BOLT  
(3 Washers, 1 Lock-Nut)  
(2) Buckle Loop  
(2) Buckle Strap  
(2) S-Hook Brace Strap  
(2) M8 x 70mm HEX BOLT  
(2 Washers, 1 Lock-Nut)  
(1) Seat Back Cushion  
(1) Seat Cushion  
(1) Cable  
(4) M8 x 70mm HEX BOLT  
(3 Washers, 1 Lock-Nut)  
(1) Shooting Rail Cover  
(4) Ground Stakes  
WRENCH (2)  
(2) M8 x 75mm HEX BOLT  
(3 Washers, 1 Lock-Nut)  
(2) D-Clips  
©2008 (rev 6/08)  
Page 4  
Ameristep® Inc.  
901 Tacoma Ct. • P.O. Box 189 • Clio, MI 48420  
(810) 686-4035  
PLATFORM ASSEMBLY  
THE  
RAPTOR TRIPOD  
Model #7700  
! NOTE: You will need:  
(1) Seat Frame Base  
(1) Seat Frame  
(1) 5½” Swivel Washer  
(1) M8 x 30mm HEX BOLT  
(2 Washers, 1 Lock-Nut)  
(1) Seat Back Cushion  
(1) Seat Cushion  
(1) Shooting Rail  
Connection  
(1) Shooting Rail Cover  
(1) Shooting Rest Pad  
(1) Back Rest  
(1) Shooting Rail  
Step 1: Seat Frame to Connection Base with 5.5”  
Washer in between them using (1) M8 x 30 mm bolt.  
1
3
2
Step 2: Mount BACK REST to SEAT FRAME using (2) M8 x 70 mm  
bolts. Assemble SHOOTING REST by inserting SHOOTING REST into  
SHOOTING REST CONNECTION; then inserting assembled SHOOTING  
REST SYSTEM into SEAT FRAME. Sliding each part of SHOOTING  
REST SYSTEM requires depressing spring-loaded buttons which are  
also used to adjust SHOOTING REST to desired position.  
Step 3: Slide on SEAT CUSHION, SEAT BACK  
CUSHION, and SHOOTING REST PADS.  
©2008 (rev 6/08)  
Page 5  
Ameristep® Inc.  
901 Tacoma Ct. • P.O. Box 189 • Clio, MI 48420  
(810) 686-4035  
PLATFORM • FOOTREST • SEAT ASSEMBLY  
THE  
RAPTOR TRIPOD  
Model #7700  
! NOTE: You will need:  
(2) Top Leg  
(2) D-Clips  
(1) Top Ladder Section  
(1) Left Platform  
(1) Right Platform  
(1) Footrest  
(2) M8 x 75mm HEX BOLT  
(3 Washers, 1 Lock-Nut)  
(2) M8 x 70mm HEX BOLT  
(2 Washers, 1 Lock-Nut)  
(2) M8 x 70mm HEX BOLT  
(3 Washers, 1 Lock-Nut)  
4
5
Step 4: Assemble PLATFORM by putting RIGHT and LEFT PLATFORM  
SECTIONS sections together and bolting them with (2) M8 x 70 mm bolts.  
Mount FOOTREST to front of PLATFORM using (2) M8 x 70 mm bolts with  
welded stoppers underneath PLATFORM.  
Step 5: Mount (2) TOP LEGS and TOP LADDER SECTION to CONNECTION BASE  
by passing TOP LEGS through PLATFORM; sliding them into CONNECTION BASE.  
Depress spring-loaded button on each TOP LEG until button snaps into hole in  
CONNECTION BASE port. Line up holes in each Top Leg with corresponding hole  
in PLATFORM and lock Legs to PLATFORM using D-CLIPS (one for each leg).  
5a  
5b  
Step 5a: Bolt TOP LADDER SECTION to CONNECTION BASE  
using (2) M8 x 45 mm bolts (fig 5a).  
Then, bolt TOP LADDER SECTION to PLATFORM  
using (2) M8 x 75 mm bolts (fig 5b).  
Page 6  
©2008 (rev 6/08)  
Ameristep® Inc.  
901 Tacoma Ct. • P.O. Box 189 • Clio, MI 48420  
(810) 686-4035  
TRIPOD LEGS  
THE  
RAPTOR TRIPOD  
Model #7700  
! NOTE: You will need:  
(2) Middle Leg  
(2) Bottom Leg  
(1) Middle Ladder Section  
6
Step 6: Slide each of (2) MIDDLE LEGS into bottom of TOP LEGS by depressing  
spring-loaded button until each leg section snaps into corresponding hole in TOP LEG  
as shown. Slide MIDDLE LADDER SECTION into bottom of TOP LADDER SECTION.  
Make sure brackets at bottom of MIDDLE LADDER SECTION face inward.  
Make sure as each ladder section is slid together, each ladder  
section has slid fully into its corresponding ladder section.  
5th Hole  
7
Step 7: Slide each of (2) BOTTOM LEGS into bottom of MIDDLE LEGS by depressing spring-loaded  
button until each leg section snaps into corresponding FIFTH HOLE from bottom of MIDDLE LEGS.  
Make sure button is in fifth hole in bottom section initially as this will make platform level on level  
ground. Once tripod is set up, use multiple adjustment holes to level tripod if ground is uneven.  
Page 7  
©2008 (rev 6/08)  
Ameristep® Inc.  
901 Tacoma Ct. • P.O. Box 189 • Clio, MI 48420  
(810) 686-4035  
STABILIZER BAR • TRUSS SYSTEM  
THE  
RAPTOR TRIPOD  
Model #7700  
! NOTE: You will need:  
(2) S-Hook Brace Strap  
(2) Buckle Loop  
(1) Cable  
(2) Buckle Strap  
(1) Stabilizer Bar  
(2) M8 x 40mm HEX BOLT  
(3 Washers, 1 Lock-Nut)  
Step 8: Mount STABILIZER BAR to brackets  
using (2) M8 x 40 mm bolts.  
8
9a  
9
Step 9: TRUSS SYSTEM; Attach BUCKLE STRAPS to PLATFORM (fig 9)  
and Bottom of BOTTOM LADDER SECTION (fig 9a).  
BUCKLE STRAP on One Side and  
BUCKLE LOOP on other side.  
Strap at Bottom  
Ladder Section  
Strap at Platform  
Assemble BUCKLE STRAPS together as shown above.  
901 Tacoma Ct. • P.O. Box 189 • Clio, MI 48420  
Page 8  
©2008 (rev 6/08)  
Ameristep® Inc.  
(810) 686-4035  
ASSEMBLY TRUSS SYSTEM CONTINUED  
THE  
RAPTOR TRIPOD  
Model #7700  
Step 10: Place HOOK END of CABLE to each BUCKLE STRAP  
(at PLATFORM and BOTTOM LADDER SECTION) looping CABLE  
over STABILIZER BAR.  
10a  
Make sure CABLE PLASTIC SLIDE makes contact with STABILIZER BAR  
BEFORE raising Stabilizer up so it is horizontal to ground. ALSO make  
sure there is ample tension in CABLE by tightening truss straps.  
Be sure truss system is tight (shown below).  
Cable  
Plastic Slide  
10b  
10  
11a  
Step 11: Attach S-HOOK BRACE STRAPS, (1) to each Leg. There is a sticker  
marking placement for each S-HOOK BRACE STRAP on each Leg.  
If sticker is not present, make sure straps are on a level, horizontal plane with  
STABILIZER BAR.  
Once BUCKLE STRAPS are wrapped around each leg and positioned properly,  
attach hooks on ends of each S-HOOK BRACE STRAP to holes on STABILIZER  
BAR (fig 11a). Make sure legs are pushed out so as to create tension on straps.  
11  
Page 9  
©2008 (rev 6/08)  
Ameristep® Inc.  
901 Tacoma Ct. • P.O. Box 189 • Clio, MI 48420  
(810) 686-4035  
GROUND STAKES • DISMANTLE TRIPOD  
THE  
RAPTOR TRIPOD  
Model #7700  
! CAUTION:  
Make sure tripod legs are on level ground at all times.  
Do not use in hazardous weather conditions such as lightning,  
high winds, and freezing rain.  
Step 12: Once tripod has been set up at desired hunting location, use (4)  
GROUND STAKES to hold tripod in place. Each leg has a foot with one hole  
for each Ground Stake to be driven through. The feet on Bottom Ladder  
Section one hole on each foot for remaining two stakes to be driven through.  
12  
DISMANTLING TRIPOD  
Step 1: Dismantle TRUSS SYSTEM by unhooking S-HOOK BRACE STRAPS  
from STABILIZER BAR, loosen TRUSS STRAPS and remove CABLE.  
Step 2: Gently tip tripod over on its side.  
3a  
Step 3: Depress spring-loaded buttons on each leg where  
MIDDLE LEGS meet UPPER LEGS. Separate MIDDLE and LOWER LEG  
SECTIONS from UPPER LEGS (fig 3).  
Depress spring-loaded buttons that adjust leg height between  
MIDDLE and LOWER LEGS and slide leg sections together and lock  
them at shortest length (fig 3a).  
3
Step 4: Remove LOWER and MIDDLE LEG SECTIONS.  
5
6
Step 6: Remove Shooting Rail by  
depressing button and sliding Rail out.  
Step 5: Remove D-CLIPS holding UPPER LEGS to PLATFORM and  
push button to release UPPER LEGS from CONNECTION BASE.  
Page 10  
©2008 (rev 6/08)  
Ameristep® Inc.  
901 Tacoma Ct. • P.O. Box 189 • Clio, MI 48420  
(810) 686-4035  
FOLDING TRIPOD FOR TRANSPORT AND STORAGE  
THE  
RAPTOR TRIPOD  
Model #7700  
! NOTE: You will need:  
(3 Parts) BackPack Straps  
(1) Sling Strap  
fig 2  
Step 8: Place CABLE in seat cushion pocket for transport.  
Install BackPack Straps as shown above.  
Step 7: Fold up remaining assembled portion.  
Step 9: Stack Leg and Ladder sections as shown and strap  
together with SLING STRAP and place GROUND STAKES in  
pocket on SLING STRAP.  
Raptor Tripod - Shown Packed  
BUCKLE STRAP INSTRUCTION  
TAG END  
1. Thread tag end of STRAP up  
through hole in underside of BUCKLE.  
2. Push "PRESS" button to allow  
tag end of STRAP to be fed through  
opening under PRESS BUTTON out  
through front.  
3. Pull tag end to adjust strap length.  
STRAP will only loosen when "Press"  
button is pushed again.  
©2008 (rev 6/08)  
Page 11  
Ameristep® Inc.  
901 Tacoma Ct. • P.O. Box 189 • Clio, MI 48420  
(810) 686-4035  
LIMITED WARRANTY  
READ THIS AGREEMENT  
This Ameristep® product has a limited warranty. No other warranties, whether expressed or implied,including warranties of  
merchantability and fitness for a particular purpose, apply to the product.  
I. GENERAL PROVISIONS OF LIMITED WARRANTY  
A. The original purchaser of this Ameristep® product is warranted against defects in material and workmanship for one year  
following the date of its retail purchase.  
B. The exclusive remedy for defects in material and workmanship under the warranty is replacement/ replacement parts.  
C. Ameristep® will, at its option, replace products not conforming to this limited warranty. This is the sole and exclusive  
remedy available under legal theory for this Ameristep® product.  
II. NO OTHER WARRANTIES  
NO OTHER WARRANTIES OR REPRESENTATIONS, WHETHER EXPRESSED OR IMPLIED, INCLUDING  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY TO THE PRODUCT.  
III. EXCLUSIONS, LIMITATIONS, ANND CONDITIONS OF LIMITED WARRANTY  
A. This warranty cannot be assigned or transferred.  
B. This warranty only applies if the Ameristep® product is used in accordance with Ameristep's written instructions.  
C. Ameristep® products are intended only for use in hunting. Ameristep® products are not intended or authorized for  
use in any situations that may create health or injury risks.  
D. This warranty is void if the product is damaged through abuse, accident, improper use, negligence or normal wear & tear.  
E. This warranty is void if the product is altered, changed, or modified in any manner.  
F. This warranty is void if any attempt is made to repair the product without written authorization from Ameristep®.  
G. Except as provided in this limited warranty, all Ameristep® products are provided "as is." All other warranties and  
representations, oral or written, express or implied,including but not limited to any implied warranties of merchantability  
or fitness for a particular purpose, are excluded and do not apply.  
IV. PROCEDURES IN EVENT OF DEFECT  
A. If you find a product to be defective, contact Ameristep at 1-810-686-4035.  
B. When you receive authorization from Ameristep®, return the product as directed by Ameristep®.  
V. LIMITATION OF DAMAGES  
A. Ameristep shall not, under any circumstances or legal theory, be liable or responsible for direct, indirect, special,  
incidental, or consequential damages.  
B. Ameristep shall not, under any circumstances or legal theory, be liable or responsible for any amount in excess of the  
product purchase price.  
C. Ameristep shall not, under any circumstances or legal theory, be liable or responsible for damage to items or equipment  
used with the Ameristep product.  
D. Ameristep shall not, under any circumstances or legal theory, be liable for personal injury, personal loss, lost profits, lost  
wages, goodwill, downtime, economic loss in excess of the product purchase price, or any non-economic damages.  
VI. ADDITIONAL PROVISIONS  
A. This agreement is the entire agreement between you and Ameristep®. This agreement supercedes any prior or different  
agreements, representations, or proposals, whether written or oral.  
B. No representative, agent, or employee, of Ameristep® is authorized to make warranties, representations, or obligations,  
other than those set for th in this limited warranty.  
C. This agreement may only be changed through an express written agreement with Ameristep®.  
D. Waiver by any party of any default or breach of this agreement will not constitute a waiver of any subsequent default or  
breach of the same or different kind.  
E. If any action or provision of this agreement is found to be invalid, such invalidity does not affect or extend to other  
sections or provisions in the agreement.  
F. This warranty gives you the specific legal rights. You may also have other rights that vary from state to state. This  
agreement shall be governed by the laws of the State of Michigan, United States of America.  
See our Full Line of Products, Accessories and Replacement Parts at:  
©2008 (rev 6/08)  
Ameristep® Inc.  
901 Tacoma Ct. • P.O. Box 189 • Clio, MI 48420  
(810) 686-4035  

AOC Car Video System e1620Sw User Manual
Canon Camera Accessories EF 1 4X III User Manual
Canon LEGRIA FS20 User Manual
Casio Calculator FX 115W User Manual
Casio s v p a m fx 300MS User Manual
Cobra Digital DVC5200 User Manual
Elite Screens Car Video System VMAX (PLUS) SERIES User Manual
Hanns G HSG1060 User Manual
Harbor Freight Tools Binoculars 41021 User Manual
JBL CS60 4 User Manual