Model: LCD4WM
3.5” Window Mounted
LCD Monitor
Installation Manual
Features
•
•
•
•
•
•
•
•
3.5” Inductive Touch Screen LCD Monitor
Low Profile, Slim Design
High Resolution TFT LCD
Built in Speaker
Two video inputs
Fully Adjustable
Auto brightness adjustment
DC12V – DC24V
Warnings
The product is intended to assist in safe driving and to allow the driver to
have a broader rear view while the vehicle is in reverse. You, as the
driver, are solely responsible for the safe operation of your vehicle and
the safety of your passengers according to local traffic regulations. Do not
use any features of this system to the extent it distracts you from safe
driving. Your first priority while driving should always be the safe
operation of your vehicle. Audiovox Electronics Corporation cannot
accept any responsibility whatsoever for accidents resulting from failure
to observe these precautions or safety instructions.
1. This product utilizes high voltage. Any unauthorized modifications or
damage to the product may result in electrical shock. Handle all
components with care. Inspect regularly for damage to components
and cabling.
2. You are responsible for ensuring that the installation of this product
does not void or affect the vehicle manufacturer’s warranty.
Audiovox Electronics Corporation or its subsidiaries are not liable in
full or in part for improper installation resulting in loss or damage to
your property, or for voiding all or part of the vehicle manufacturer’s
warranty.
3. Do not apply excessive force to any of the components contained
within this kit. Excessive force used before, during or after
installation that results in a damaged or non-functional part will void
all warranties.
4. Please follow the procedures in this installation manual. Improper
installation or modification of this product will void all warranties.
3
Product Description
This advanced high resolution monitor will show a clear picture from a
reversing camera or any other video source.
The modern thin design and no button touch screen and built in speaker
are all features not found on competitive products.
The LCD is perfect for use on your car, truck, or van.
This wired Monitor is designed for use with an Advent camera but is
compatible with most video sources and other cameras and can be
connected using a standard RCA connector.
Packing List
Parts
Barcode # Quantity
3.5" Window Mount Monitor
30252030
30252160
1
1
5M Power Harness (8-Pin) & S-Video (M) to RCA (F)
Adaptor
5M Extension Cable (4-Pin)
Mounting Bracket
Manual
30252170
30252060
30252020
1
1
1
4
LCD Monitor Installation
1. Choose a suitable place for the screen in clear view of the driver
(recommended positions include next to the Rear Vision Mirror or in
the corner of the front window).
2. Examine the vehicle to determine the best way to run the power wires
to: accessory power, the reverse lights and to the camera at the rear of
the vehicle.
3. Mount the ‘tombstone’ metal lug onto the front Windscreen with
Permatex adhesive – follow the Permatex instructions on
application/drying.
4. Run the wiring harness from the LCD location to the rear of the
vehicle.
5. Attach reverse & accessory power wires.
6. Connect your reversing camera.
Note: When using a Advent Camera with your Advent Monitor the signal
and power for the camera will be supplied through the monitor extension
cable. Please also note that the microphone in the camera will be played
on the speaker built into the LCD monitor.
7. Connect the LCD Monitor to the harness.
8. Power up and adjust on screen settings.
NOTE: To adjust monitor settings lightly touch along the bottom of the
screen to enact the inductive screen menu and follow prompts.
5
Wiring the Camera to the Vehicle’s Reverse Lamp
1. Locate the reverse lamp in the tail light assembly.
2. Using the tap connector supplied, perform the following steps:
a) Place the un-stripped positive lead from the tail lamp in the run
channel, which runs completely through the connector.
b) Insert the un-stripped red power wire from the camera
completely into the other channel in the connector.
c) Make the connection between the wires by crimping down the
metal connector with a pair of pliers, making sure the metal is
flush with the plastic insulator.
d) Close the top plastic hinged cover until latched.
3. Attach the black wire to the ground (negative).
4. Repeat the above steps for the red wire.
6
Monitor Wiring Diagram
Note: If used with an Advent camera – the power and signal will be
provided through a single cable from the monitor.
Specifications
1. Voltage: DC9V – DC28V
2. Current: 300mA Maximum
3. Signal System: Switchable
4. Viewing Angle: 160 degrees
5. Minimum Illumination: 0.7 Lux
6. Image Display: Selectable Normal/Reverse Image
7. Adjustable Viewing Angle
7
Troubleshooting
Symptom
Solution
No power to the monitor
1. Check that reverse power is
attached to orange wire.
2. Check that accessory power is
attached to red wire
3. Check that black is attached to
vehicle body (ground)
4. Check fuse and if blown
ONLY replace is fuse of same
amperage.
No image from backup camera
when vehicle placed in reverse
1. Check that camera is
functioning correctly
2. Check that orange wire is
attached to reverse power.
3. Check that backup camera is
attached to input CAM1.
Image is mirrored or requires
adjustment
1. All settings are adjusted by
pressing on the bottom right
corner of the screen (*Touch)
and following prompts.
Sound can not be heard from
Advent camera
1. Increase volume through touch
menu.
8
7
© 2008 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788
|