Table of Contents
TCO03 Notice............................................................................................................................................................
FCC Statement Warning............................................................................................................................................
Canadian DOC Notice...............................................................................................................................................
Precautions................................................................................................................................................................
Package Contents......................................................................................................................................................
Installation Instructions..............................................................................................................................................
Assembling the Monitor...................................................................................................................................
Detaching the Monitor .....................................................................................................................................
Adjusting the Viewing Angle ...........................................................................................................................
Connecting the Devices ..................................................................................................................................
Switching the Power .......................................................................................................................................
Adjusting Display Settings .........................................................................................................................................
External Controls ............................................................................................................................................
OSD Options .............................................................................................................................................................
OSD Menu ................................................................................................................................................................
Brightness & Contrast ...............................................................................................................................................
Tracking ..........................................................................................................................................................
Position ...........................................................................................................................................................
Color ...............................................................................................................................................................
Language Setting.............................................................................................................................................
OSD Option.......................................................................................................................................................
Autoconfiguration.............................................................................................................................................
Information ....................................................................................................................................................
Recall...............................................................................................................................................................
General Specifications...............................................................................................................................................
Technical Information.................................................................................................................................................
1
2
3
3
4
4
4
4
4
4
5
5
5
5
6
6
6
6
6
7
7
7
7
7
8
8
Pin Assignment ................................................................................................................................................. 9
Standard Timing Table........................................................................................................................................10
Troubleshooting................................................................................................................................................
11
IT Equipment Recycling Information
IT Equipment Recycling Information:
Acer is strongly committed to environmental protection and views recycling, in the form
of salvaging and disposal, of used equipment as one of the company’s top priorities in
minimizing the burden placed on the environment.
We at Acer are very conscious of the environmental forces that impose on our business
and strive to identify and provide the best working products to reduce the environmental
impact of our products.
For more information and help in recycling, please visit the following websites:
Worldwide:
and benefits.
Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF
ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE
ELECTRONIC INDUSTRIES ALLIANCE AT WWW. EIAE. ORG. FOR LAMP SPECIFIC DISPOSAL
INFORMATION CHECK WWW. LAMPRECYCLE. ORG.
Waste Electrical and Electronic Equipment (WEEE) Directive
Do not throw this electronic device into the municipal trash bin when discarding. To
minimize pollution and ensure utmost protection of the global environment, please recycle
it. For more information about the collection of WEEE welcome to visit our homepage at
www.acer.com under environment.
2
NOTE
A shielded-type signal cord is required in order to meet the FCC emission limits and also to prevent interference to
the radio and television reception. It is essential that only the supplied signal cord be used.
Canadian DOC Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numerique de la classe B repecte toutes les exigences du Reglement
sur le materiel brouilleur du Canada.
Preface
This manual is designed to assist users in setting up and using the LCD Monitor. Information in his document has
been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The
information in this document is subject to change without notice. This document contains proprietary information
protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of the manufacturer.
Important Safety Instructions
1. To clean LCD Monitor screen;Power off LCD Monitor and unplug the AC Cord.
Spray a non-solvent cleaning solution onto a rag and clean the screen gently.
2. Do not place the LCD Monitor near a window. Exposing the monitor to rain
water, moisture or sunlight can severely damage it. ter, moisture or sunlight can
severely damage it.
3. Do not apply pressure to the LCD screen.
Excess pressure
may cause permanent damage to the display.
4. Do not remove the cover or attempt to service this unit by yourself. Servicing of any
nature should be performed by an authorized technician.
5. Operate LCD Monitor in a room with a room temperature of 5°C ~ 40°C (or 41°F ~
104°F).Operating the LCD Monitor outside this range could result in permanent damage.
6. If any of the following occurs, immediately unplug your monitor and call an authorized
technician.
* Monitor to PC signal cable is frayed or damaged.
* Liquid spilled into LCD Monitor or the monitor has been exposed to rain.
* LCD Monitor or the case is damaged.
3
Package Contents
LCD Monitor
Power Cord
VGA cable
User manual (CD)
Quick start Guide
Assembling the Monitor
1. Position the monitor on top of the stand.
2.Connect the stand into the neck of monitor along the track.
Detaching the Monitor
Important
First, find a clean, flat surface to place the monitor after removing it from the stand. Place a clean dry cloth under the
monitor to protect it further. Pull the monitor slightly up and away from the stand.
Adjusting the Viewing Angle
The viewing angle of the monitor ranges from forward 5° to backward 15°.
Caution:
Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in
damaging the Monitor and Monitor stand.
Connecting the Devices
Please shut down the power of computer and monitor
before you do the connection.
Attach the monitor to the power cord which should then be
inserted into a properly grounded electric socket.
(1)
Power Cord
Connect the signal cable to the VGA output socket of the graphics card
on the computer. Then tighten the thumbscrews on the connector
(
VGA Cable
2)
WARNING: The D-Sub 15 pin plug of the VGA cable is trapezoid in shape. Make sure the shape of the plug matches
the shape of the socket it is inserted into, and that none of the pins are bent or otherwise damaged.
Operating Your Monitor
First, switch the power on to the monitor, then switch the power on to the computer. When you see the LED on
the power button go green, this indicates the computer is ready for use. Allow about 10 seconds for the video
signal to appear. If you do not see the green light on the power button or a video signal, check the connections .
If OSD is active, press to exit. If OSD is inactive, press and the
monitor will automatically optimize the display position, clock and
phase of your display.
1
AUTO
2
If OSD is active, press to select or adjust OSD options.
If OSD is active, press to select or adjust OSD options.
Press to view OSD. Press again to exit.
4
MENU
OSD Menu
Power on/off
Green: power on
Orange: in sleep mode
OSD Options
Please refer to "External Controls " on Page 5. To adjust the OSD settings :
1. Press the MENU button to open the OSD menu.
2. Use the buttons marked < or >, to highlight a control, then press the MENU button to enter
3. Use the buttons marked < or >, to adjust the control to the desired level.
4. When you have finished making all selections, press the MENU button to exit the OSD. (Or the adjustment
will auto-save after 45 seconds.)
OSD Menu
Brightness & Contrast
BRIGHTNESS:
This adjusts the brightness of the picture on the screen.Adjustable range
from the value of 0 to 100.
CONTRAST:
This adjusts dark and light shades of color relative to each other to achieve
a comfortable contrast. Adjustable range from the value of 0 to 100.
Tracking
FOCUS:
This removes any horizontal distortion and makes the picture clear and sharp.
CLOCK:
If there are any vertical stripes seen on the background of the screen this renders
them less noticeable by minimizing their size. It also changes the size of horizontal
screen.
Position
V-Position:
This removes any horizontal distortion and makes the picture clear and sharp.
H-Position:
This adjusts the horizontal.
Color Temperature
There are three ways of adjusting color temperature:
WARM:
Set the color temperature as CIE coordinate 6500°K.
COOL:
Set the color temperature as CIE coordinate 9300°K.
User defined:
You can adjust the colors red, green and blue to the intensity you
desire.
Language
Select the OSD menu language.
OSD Position
This changes the position of the OSD window on the screen.
TIMEOUT function allow user define the OSD appearing period from 10 seconds to
120 seconds.
AUTO Configuration
Adjust the monitor parameter automatically.
Source Change
Analog and Digital source change .(option)
Information
This shows brief information on the screen.
Recall
Recall to factory default settings
General Specification
Item
Specification
15-inch Flat panel active-matrix TFT LCD
1024 x 768 @75Hz
0.297 mm X 0.297 mm
16.2M
Display
Max resolution
Pixel Pitch
Color
Brightness
Contrast Ratio
250nits ( Typical)
450:1 (Typical)
Response Time
16ms (Typical)
120°
View Angle of Horizontal
View Angle of Vertical
External Controls Power Button
Control Buttons
100°
ON/ OFF
AUTO, MENU, <, >
VGA
Video In
Video
Analog 0.7V
Sync
TTL (+/ -)
DDC2B
Plug & Play
Power Source
100-240V AC, 50/60 Hz, 1.5A
Power consumption during
normal operation
< 25W
Power consumption during
active off operation
< 1W
Dimension (W_H_D)
Weight (Net/ Gross)
341x356.4x167.6mm (base included)
2.6Kg/ 4.1Kg
8
Technical Information
Pin Assignment
Signal
Signal
PIN
1
Description
Red
PIN
9
Description
+5V
2
Green
10
11
12
13
14
15
N.C.
3
Blue
N.C.
4
N.C.
DDC_SDA
HSYNC
VSYNC.
DDC_SCL
5
GND
6
Red_GND
Green_GND
Blue_GND
7
8
9
Standard Timing Table
If the selected timing is NO T included in table below, this LCD monitor will go into the sleep mode.
VESA MODES
Horizontal
Vertical
Mode
Resolution
Total
Nominal
Frequency
+/-0.5KHz
Sync
Polarity
Nominal
Frequency
+/-1Hz
Sync
Polarity
Nominal
Pixel
Clock
(MHz)
640*480@60Hz
640*480@72Hz
640*480@75Hz
800*600@56Hz
800*600@60Hz
800*600@72Hz
800*600@75Hz
1024*768@60Hz
1024*768@70Hz
1024*768@75Hz
800*525
31.469
N
N
N
P
P
P
P
N
N
P
59.940
72.809
75.000
56.250
60.317
72.188
75.000
60.004
70.069
75.029
N
N
N
P
P
P
P
N
N
P
25.175
VGA
832*520
37.861
31.500
31.500
36.000
40.000
50.000
49.500
65.000
75.000
78.750
840*500
37.500
1024*625
1056*628
1040*666
1056*625
1344*806
1328*806
1312*800
35.156
SVGA
37.879
48.077
46.875
48.363
XGA
EGA
56.476
60.023
IBM MODES
640*350@70Hz
720x400@70Hz
800*449
900*449
31.469
31.469
P
N
70.086
P
N
25.175
28.322
70.087
MAC MODES
49.728
57.284
SVGA
XGA
832*624@75Hz
1024*768@60Hz
1024*768@75Hz
1152*667
1312*813
1328*804
N
N
N
74.551
60.001
74.927
N
N
48.780
64.000
80.000
XGA
60.241
N
Troubleshooting
This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among
various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new
display mode or new VGA cardis selected.
Attention
This LCD Monitor Supports Multiple VGA Modes. Refer to the Standard Timing Table for a listing of modes supported
by this LCD Monitor.
PROBLEM Picture is unclear and unstable
The picture is unclear and unstable, please perform the following steps :
1. Enter PC to "Shut Down Windows" status while you're in MS-Windows environment.
2. Check the screen to see if there's any black vertical stripes appear. If there are,take advantage of the "Clock"
function in OSD menu and adjust (by increment or decrement numbers)until those bars disappear.
3. Move to "FOCUS" function in OSD menu again and adjust the monitor screen to its most clear display.
4. Click "No" on "Shut Down Windows" and back to the normal PC operating environment.
PROBLEM There is no picture on LCD Monitor
If there's no picture on the LCD Monitor, please perform the following steps:
1. Make sure the power indicator on the LCD Monitor is ON, all connections are secured,and the system is running
on the correct timing. Refer to Chapter 3 for information on timing.
2. Turn off the LCD Monitor and then turn it back on again. If there is still no picture,press the Adjustment Control
button several times.
3. If step 2 doesn't work, connect your PC system to another external CRT.If your PC system Functions properly with
a CRT Monitor but it does not function with the LCD Monitor,the output timing of the VGA card may be out of the
LCD's synchronous range.
Please change to an alternative mode listed in the Standard Timing Table or replace the VGA card,and then repeat
steps 1 and 2.
PROBLEM There is no picture on LCD Monitor
If you have chosen an output timing that is outside of the LCD Monitor's synchronous range (Horizontal: 24 ~ 80 KHz
and Vertical:56 ~ 75 Hz), the OSD will display a "Out of Range" message. Choose a mode that is supported by your
LCD Monitor. Also, if the signal cable is not connected to LCD monitor at all or properly, the monitor screen will
a message "No Input Signal".
display
Caution: Do not attempt to service the monitor yourself or open the computer yourself.
Please refer all servicing to qualified service personnel if the problems cannot be solved in "Troubleshooting" section.
11
|