York Evaporator Blowers K4eu090 User Manual

036-21300-002-A-0905

DESCRIPTION

These completely assembled units include a well-insulated cabinet, a

DX cooling coil with copper tubes and aluminum fins, expansion

valve(s), distributor(s), throwaway filters, a centrifugal blower, a blower

motor, an adjustable belt drive, a blower motor contactor and a small

holding charge of refrigerant-22.

The units are shipped in the vertical position ready for field installation.

They can be installed for horizontal operation by reversing the position

of the solid bottom panel with the return air duct flange on the front of

the unit.

Technical Guide

ACCESSORIES—FIELD INSTALLED

SUPPLY AIR PLENUMS

SPLIT-SYSTEM

These fully insulated plenums are available for free standing units

located within the conditioned space, are shipped knocked-down for

easy field assembly, are finished to match the exterior of the basic

unit, and have double deflection grills that can be adjusted to vary the

throw, spread and drop of the supply air.

EVAPORATOR BLOWERS

K2EU060, K4EU090, K3EU120 &

K3EU180

RETURN AIR GRILLS

These expanded metal grills are available for free standing units

located within the conditioned space, are finished to match the exterior

of the basic unit and are shipped in one piece for easy installation.

5 THRU 15 NOMINAL TONS

BASES

Bases are available to raise vertical units above the floor. Outdoor air

may be introduced through these bases by cutting an access opening

to accommodate the outdoor air duct connection. These bases are fin-

ished to match the exterior of the basic unit. They may have to be insu-

lated in the field for certain applications.

THREE-PHASE ELECTRIC HEATERS

Electric heaters are available in several capacities to provide maxi-

mum flexibility. Both the air conditioning unit and the heater can be

selected to precisely match the cooling and heating requirements of

the conditioned space. These heaters are designed for easy field

installation over the supply air opening of the unit. They have been

tested by and will be shipped with a CSA label. Every heater will be

fully protected against excessive current and temperature by fuses

and two high limit thermostats.

Units with electric heat will require only one power supply for both the

heating elements and the supply air blower motor, and the power wir-

ing can be protected by either dual element/time delay fuses or an

inverse time circuit breaker.

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

036-21300-002-A-0905

NOMENCLATURE

<RUNꢃ,QGRRUꢃ6SOLWꢃ6\VWHPꢃ3URGXFWꢃ1RPHQFODWXUH

. ꢄ (8 ꢀꢁꢀ $ ꢂꢂ

3URGXFWꢃ&DWHJRU\

.ꢁ ꢁ$LUꢁ+DQGOHUꢊꢁ6SOLWꢁ6\VWHPꢊꢁ$&

9ROWDJHꢃ&RGH

ꢂꢃꢁ ꢁꢆꢂꢇꢈꢆꢅꢂꢉꢍꢉꢃꢂ

ꢅꢅꢁ ꢁꢆꢂꢇꢈꢆꢅꢂꢉꢅꢉꢃꢂꢊꢁꢀꢃꢂꢉꢅꢉꢃꢂ

ꢄꢇꢁ ꢁꢄꢌꢄꢉꢅꢉꢃꢂ

3URGXFWꢃ*HQHUDWLRQ

ꢀꢁ ꢁ)RXUWKꢁ*HQHUDWLRQ

3URGXFWꢃ,GHQWLILHU

(8ꢁ ꢁ5ꢉꢆꢆꢊꢁ6WDQGꢋꢁ(IIꢋꢊꢁꢆꢉ3LSH

+HDWꢃ7\SHꢃ ꢃ1RPLQDOꢃ+HDWꢃ&DSDFLW\

$ꢁ ꢁ&RROLQJꢁ2QO\ꢁꢉꢁ6XLWDEOHꢁIRUꢁILHOGꢁLQVWDOOHGꢁHOHFWULFꢁKHDW

1RPLQDOꢃ&RROLQJꢃ

&DSDFLW\ꢃꢅꢃ0%+

ꢂꢃꢂꢁ ꢁꢄꢁ7RQ

ꢂꢎꢂꢁ ꢁꢌꢉꢍꢈꢆꢁ7RQ

ꢍꢆꢂꢁ ꢁꢍꢂꢁ7RQ

ꢍꢇꢂꢁ ꢁꢍꢄꢁ7RQ

THERMOSTATS

ACCESSORIES-FIELD INSTALLED (CONT.)

Wall-mounted thermostats and subbases (24-volt) with sys-

tem and fan switches are available to control the operation of

these split system air conditioners.

HOT WATER COILS

These drainable coils have 2 rows of 1/2" copper tubes, 12

aluminum fins per inch, a casing that is finished to match the

exterior of the basic unit, but no water control valve. The coils

slide out of their casings for easy field installation. They

should be mounted over the return air opening on 5, 7-1/2

and 10-ton units—between the unit coil and blower sections

on 15-ton units.

APPLICATION FLEXIBILITY

MODELS 5, 7-1/2 & 10 TON

These units are built in a single cabinet with two condensate

drain pans. This allows the units to be installed in either the

vertical or horizontal position for maximum flexibility.

STEAM COILS

On vertical applications, the air velocity across the cooling

coil keeps the condensate from dripping off the finned sur-

face onto the filters.

These non-freeze coils have 1 row of 1" copper tubes, a 5/8"

copper tube inside each 1" tube to distribute the steam evenly

across the entire length of the coil, 8 aluminum fins per inch,

a casing that is finished to match the exterior of the basic unit,

but no steam control valve. The coils slide out of their casings

for easy field installation and are pitched in their casings to

facilitate condensate drainage. They should be mounted over

the return air opening on 5, 7-1/2 and 10-ton units—between

the unit coil and blower sections on 15-ton units.

On horizontal applications, the unit must be installed with the

condensate drain pan under the entire cooling coil.

•

The Supply Air Plenum and the Return Air Grill accesso-

ries can be used on either arrangement.

The Base accessory can only be used on the vertical

arrangement.

•

SUSPENSION KIT

Units installed horizontally are designed for ceiling suspen-

sion. Four 3/8"-16 weld nuts are provided in the angle sup-

ports on the front of the unit (the side with the logo).

Knockouts are provided in the exterior panels for access to

these weld nuts. The hanger rods must be supplied in the

field.

Suspension kit 1HH0451 is available for 15-ton units installed

horizontally. The accessory includes two channel iron sup-

ports and the hardware to secure them to the top of the unit.

The hanger rods must be supplied by the field.

Unitary Products Group

036-21300-002-A-0905

MODEL 15 TON

$,5

287

These units have two distinct modules . . . a blower module

and a coil module. Although the unit is always shipped in the

vertical position with a vertical air discharge as shown in illus-

tration (a), the blower module can be repositioned in the field

as shown in illustrations (b) and (c) for maximum flexibility.

%/2:(5

%/2:(5ꢁ02725

&2,/

5(7851ꢁ$,5

'8&7ꢁ)/$1*(

•

The Supply Air Plenum, Return Air Grill and Base acces-

sories can be applied on arrangement (a).

The Return Air Grill and Base accessories can be

applied on arrangement (b).

The Supply Air Plenum, Return Air Grill and Suspension

accessories can be applied on arrangement (c).

&21'(16$7(

'5$,1

&211(&7,21

$,5ꢁ

&21'(16$7(

'5$,1ꢁ3$1

),/7(56

ꢆ9(57,&$/ꢃ326,7,21ꢇ

),/7(56

&2,/

5(7851

$,5ꢁ'8&7

)/$1*(

%/2:(5

$,5ꢁ

$,5

287

%/2:(5ꢁ02725

&21'(16$7(ꢁ'5$,1ꢁ3$1

&21'(16$7(

'5$,1ꢁ&211(&7,21

ꢆ+25,=217$/ꢃ326,7,21ꢇ

FIGURE 1 - VERTICAL AND HORIZONTAL

APPLICATION KEU060, 090 & 120

ꢏ9(57,&$/ꢁ326,7,21ꢐ

ꢏ+25,=217$/ꢁ326,7,21ꢐ

FIGURE 2 - VERTICAL AND HORIZONTAL APPLICATION KEU180

Unitary Products Group

036-21300-002-A-0905

ꢆꢉꢄꢈꢇ

ꢏꢀꢐꢁꢅꢈꢇꢑꢉꢍꢃ

:(/'ꢁ18876

ꢀꢋꢂꢉꢄꢃꢈ ꢆ+%5ꢇꢈꢇ

ꢁꢁꢂꢋꢄꢌ ꢆ+%5ꢇꢉꢇꢊ ꢃꢅꢇ

ꢀꢁꢂꢃꢄꢅ ꢆ+%5ꢇꢈꢇ

ꢁꢉꢂꢃꢄꢁ ꢆ+%5ꢇꢉꢇꢊ ꢃꢅꢇ

ꢍꢉꢍꢈꢀꢁꢏ.(8ꢂꢃꢂꢐ

ꢍꢉꢅꢈꢇꢁꢏ.(8ꢂꢎꢂꢊꢁꢍꢆꢂꢐ

;

&(17(5

2)ꢁ*5$9,7<

!)2

/54

5(7851ꢁ$,5ꢁ*5,//ꢊꢁ+27ꢁ:$7(5ꢁ&2,/ꢁ

$1'ꢁ67($0ꢁ&2,/ꢁ$&&(6625,(6ꢁ

,167$//('ꢁ217+,6ꢁ(1'ꢁ2)ꢁ7+(ꢁ81,7ꢋ

6833/<ꢁ$,5ꢁ3/(180ꢁ$1'

(/(&75,&ꢁ+($7(5ꢁ$&&(6625,(6

,167$//('ꢁ21ꢁ7+,6ꢁ(1'ꢁ2)ꢁ7+(

81,7ꢋ

FIGURE 3 - SUSPENSION MOUNTING (HORIZONTAL) - KEU060, 090 AND 120

TABLE 1: UNIT SUSPENSION MOUNTING (HORIZONTAL APPLICATION) WEIGHTS

Shipping

Weight

(lb)

Operating

Weight

(lb)

CG (in)

4-Point Loading (lb)

Unit Model

K*EU060

K*EU090

K*EU120

K*EU180

225

210

22.50

26.50

15.00

24.00

340

235

370

355

440

425

104

141

TABLE 2: KEU OPERATING WEIGHTS (LBS.)

MODEL

060

210

090

120

180

BASIC UNIT

(Cooling Only)

Base

325

425

Return Air Grill

Supply Air Plenum

Hot Water Coil

Steam Coil

100

105

115

100

105

115

135

145

ACCESSORIES

10 KW

16 KW

26 KW

36 KW

72 KW

Electric Heater

125

Unitary Products Group

036-21300-002-A-0905

ꢏꢀꢐꢁ+DQJHUꢁ5RGV

ꢏ)LHOGꢁ6XSSOLHGꢐ

ꢅꢑ

ꢒ6XVSHQVLRQ

ꢁ&KDQQHOV

$,5ꢁ,1

&2,/

6(&7,21

ꢍ

5HIHUꢁWRꢁ3DUWꢁ1Rꢋꢁ

%/2:(5

6(&7,21

$,5ꢁ287

ꢂꢅꢄꢉꢍꢃꢃꢆꢆꢉꢂꢂꢍꢁIRU

LQVWDOODWLRQꢁLQVWUXFWLRQVꢁRQ

WKHꢁVXVSHQVLRQꢁDFFHVVRU\

DQGꢁIRUꢁWKHꢁLQGLYLGXDOꢁORDG

RQꢁHDFKꢁKDQJHUꢁURGꢋ

5(7851ꢁ$,5ꢁ*5,//(

$FFHVVRU\ꢁ,QVWDOOHG

2Qꢁ7KLVꢁ(QGꢁ2Iꢁ8QLW

6833/<ꢁ$,5ꢁ3/(180

$QGꢁ(/(&75,&ꢁ+($7(5

$FFHVVRULHVꢁ,QVWDOOHGꢁ2Q

7KLVꢁ(QGꢁ2Iꢁ8QLW

FIGURE 4 - SUSPENSION ACCESSORY (HORIZONTAL) - KEU180

TABLE 3: SOUND POWER RATINGS

SOUND POWER (dB 10^-12WATTS)

ESP

IWG

BLOWER

OCTAVE BAND CENTERLINE FREQUENCY (HZ)

UNIT

MODEL

CFM

dB(A)

10 FT.¹

RPM

BHP

125

250

500

1,000

2,000

4,000

8,000

SWL dB(a)

060

090

120

180

2,000

3,000

4,000

6,000

0.50

0.60

0.70

0.75

940

750

850

750

0.70

1.05

1.75

2.75

1. At a distance of 10 feet from the blower.

NOTE:

These values have been accessed using a model of sound propagation from a point source into the hemispheric free field. The dBA values provided are

for reference only. Calculation of dBA values cover matters of system design and the fan manufacturer has no way of knowing the details of each sys-

tem. This constitutes an exception to any specification or guarantee requiring a dBA value or sound data in any other form than sound power level rat-

ings.

Unitary Products Group

036-21300-002-A-0905

TABLE 4: HEATING CAPACITY - ELECTRIC HEAT ACCESSORY

CAPACITY

1ST STAGE 2ND STAGE

NOMINAL RATINGS¹

UNIT MODEL

HEATER MODEL

VOLTAGE TEST

MBH

34.2

54.7

88.9

MBH

34.2

54.7

MBH

2HT045010

2HT045016

2HT045026

208 / 240²

480³

060

20.5

34.2

2HS045010

2HS045016

2HS045026

2HS045036

2HS045010

2HS045016

2HS045026

2HS045036

2HS045072

34.2

54.7

88.9

123

34.2

54.7

34.2

54.7

123

600⁴

208 / 240²

480³

20.5

34.2

68.3

600⁴

090, 120

208 / 240²

480³

600⁴

208 / 240²

480³

600⁴

208 / 240²

280³

34.2

54.7

88.9

123

600⁴

208 / 240²

280³

20.5

34.2

68.3

123

600⁴

208 / 240²

280³

180

600⁴

208 / 240²

280³

600⁴

208 / 240²

280³

246

600⁴

1. Capacity Ratings do not include the heat generated by the air blower motor.

2. For 208 volts, multiply the MBH and KW by (208/240)² or 0.751.

For 230 volts, multiply the MBH and KW by (230/240)² or 0.918.

3. For 460 volts, multiply the MBH and KW by (460/480)² or 0.918.

4. For 575 volts, multiply the MBH and KW by (575/600)² or 0.918.

Unitary Products Group

036-21300-002-A-0905

TABLE 5: STEAM COIL CAPACITY , MBH@2 PSIG

DRY BULB TEMPERATURE OF AIR ENTERING COIL, ºF

STEAM COIL

UNIT MODEL

CFM

MODEL

1600

2000

2400

3000

3600

3200

4000

4800

6000

7200

104.0

115.2

124.9

172.2

191.2

207.5

196.4

217.3

236.1

298.2

329.1

356.4

94.0

83.9

73.9

1NF0450

060

104.0

113.0

155.5

172.6

187.1

177.6

195.3

212.9

268.4

297.0

321.8

93.1

81.9

100.9

139.1

154.3

167.4

158.8

175.3

190.4

236.7

265.6

287.9

89.0

122.4

136.0

147.4

140.0

154.8

167.8

211.5

234.1

254.0

090

120

180

1NF0451

1NF0452

1. These capacities do not include any blower motor heat.

2. Multiply these capacities by the following factors to correct for higher steam pressures.

Steam Pressure, psig

Capacity correction factor

1.05

1.12

1.19

1.25

1.30

NOTE: Steam rate (lb./hr.) = 1.025 x MBH

CAUTION: Do NOT operate a motor above its nominal HP rating when a unit is equipped with a steam coil acces-

sory.

TABLE 6: HOT WATER CAPACITY , MBH

ENTERING WATER TEMP. MINUS ENTERING AIR TEMP., ºF

WATER COIL MODEL

UNIT MODEL

GPM

CFM

110

130

150

1600

2000

2400

3000

3600

3200

4000

4800

6000

7200

46.5

60.4

74.6

89.0

101.8

113.4

123.3

169.7

190.4

208.1

196.6

218.6

237.4

294.1

326.6

354.3

1HW0450

060

51.7

67.2

83.0

99.2

56.0

73.0

90.4

107.9

148.5

166.6

182.1

172.1

191.3

207.5

257.4

285.9

309.8

78.0

101.3

113.3

124.0

117.1

130.2

140.9

175.1

195.0

210.8

124.7

139.6

153.0

144.6

160.7

174.3

215.8

240.3

260.4

090

120

180

87.7

95.5

1HW0451

1HW0452

90.3

100.2

108.3

135.5

150.0

162.4

1. These capacities do no include any blower motor heat.

NOTE: Water Temperature Drop, F = 2 x MBH

CAUTION: Do NOT operate a motor above its nominal HP rating when a unit is equipped with a hot water coil accessory.

TABLE 7: PRESSURE DROP VS. GPM

TABLE 8: CAPACITY CORRECTION VS. GPM

GPM

Pressure Drop, PSI

GPM

.10

.32

.67

GPM

Capacity Correction

GPM

1.12

1.16

1HW0450

1HW0451

1HW0452

1HW0450

1HW0451

1HW0452

Pressure Drop, PSI

GPM

.17

.58

1.22

Capacity Correction

GPM

1.11

1.15

Pressure Drop, PSI

.20

.67

1.41

Capacity Correction

1.12

1.17

Unitary Products Group

036-21300-002-A-0905

TABLE 9: SUPPLY AIR BLOWER PERFORMANCE - KEU060 (5 TON)

EXTERNAL STATIC PRESSURE

CFM

0.2

0.4

0.6

0.8

RPM

677

BHP

0.08

0.24

0.39

0.54

0.70

0.88

1.07

1.27

1.50

1.74

RPM

753

BHP

0.19

0.35

0.50

0.65

0.81

0.99

1.17

1.38

1.60

1.85

RPM

831

BHP

0.29

0.45

0.60

0.75

0.91

1.09

1.27

1.48

1.70

1.95

RPM

912

BHP

0.38

0.54

0.69

0.85

1.01

1.18

1.37

1.57

1.80

----

1400

1600

1800

2000

2200

2400

2600

2800

3000

3200

174

325

466

607

757

918

1094

1286

1495

1721

268

355

506

647

789

938

1100

1276

1468

1677

----

725

225

366

507

657

818

994

1187

1395

1622

801

879

419

959

773

849

927

560

1008

1056

1106

1156

1207

1258

1311

----

822

898

975

701

871

947

1025

1075

1126

1178

1230

1283

851

922

997

1012

1188

1380

1589

1815

972

1048

1100

1152

1205

1024

1076

1129

EXTERNAL STATIC PRESSURE

1.2 1.4

CFM

1.0

1.6

RPM

997

BHP

0.47

0.63

0.78

0.93

1.09

1.27

1.45

1.66

1.88

----

RPM

1086

1134

1182

1230

1280

1330

1381

1433

1485

----

BHP

0.54

0.71

0.86

1.01

1.17

1.34

1.53

1.74

1.96

----

RPM

1181

1228

1276

1325

1375

1425

1476

1527

----

BHP

0.61

0.77

0.92

1.08

1.24

1.41

1.60

1.80

----

RPM

1282

1329

1377

1426

1476

1526

1577

1628

----

BHP

0.67

0.83

0.98

1.13

1.29

1.47

1.66

1.86

----

1400

1600

1800

2000

2200

2400

2600

2800

3000

3200

435

586

727

869

1018

1180

1356

1548

1757

----

507

570

622

774

914

1056

1205

1367

1543

1735

----

1044

1092

1141

1191

1241

1292

1343

1395

----

658

721

799

861

940

1003

1153

1314

1490

1682

----

1090

1251

1427

1620

1828

----

Exceeds the BHP limitation.

Unitary Products Group

036-21300-002-A-0905

TABLE 10: SUPPLY AIR BLOWER PERFORMANCE - KEU090 (7.5 TON)

EXTERNAL STATIC PRESSURE

CFM

0.2

0.4

0.6

0.8

RPM

561

579

599

619

640

662

684

706

728

750

771

792

813

BHP

0.30

0.44

0.58

0.71

0.84

0.97

1.09

1.20

1.31

1.42

1.52

1.62

1.72

RPM

612

630

649

670

691

713

735

757

779

800

822

843

864

BHP

0.43

0.57

0.71

0.84

0.97

1.10

1.21

1.33

1.44

1.55

1.65

1.75

1.84

RPM

670

688

707

728

749

771

793

815

837

859

880

901

922

BHP

0.57

0.71

0.85

0.98

1.11

1.23

1.35

1.47

1.58

1.69

1.79

1.89

1.98

RPM

734

752

771

792

813

835

857

879

900

922

944

965

986

BHP

0.71

0.85

0.99

1.12

1.25

1.37

1.49

1.61

1.72

1.83

1.93

2.03

2.12

2200

2400

2600

2800

3000

3200

3400

3600

3800

4000

4200

4400

4600

281

400

530

661

414

533

663

794

542

662

792

922

666

786

916

1047

1166

1282

1393

1500

1603

1702

1798

1890

1979

786

905

1035

1151

1262

1369

1472

1571

1667

1759

1848

901

1021

1132

1239

1342

1441

1537

1629

1718

1013

1120

1223

1322

1418

1510

1599

EXTERNAL STATIC PRESSURE

1.2 1.4

CFM

1.0

1.6

RPM

801

819

838

859

880

902

924

945

967

989

1011

1032

1052

BHP

0.84

0.98

1.12

1.25

1.38

1.51

1.63

1.74

1.85

1.96

2.06

2.16

2.25

RPM

869

BHP

0.95

1.09

1.23

1.36

1.49

1.62

1.74

1.85

1.96

2.07

2.17

2.27

----

RPM

936

BHP

1.03

1.17

1.31

1.45

1.57

1.70

1.82

1.93

2.04

2.15

2.25

----

RPM

1000

1018

1038

1058

1079

1101

1123

1145

1167

1189

1210

----

BHP

1.07

1.21

1.35

1.49

1.61

1.74

1.86

1.97

2.08

2.19

2.29

----

2200

2400

2600

2800

3000

3200

3400

3600

3800

4000

4200

4400

4600

783

886

962

999

916

887

1019

1148

1272

1392

1507

1618

1725

1828

1928

2023

2116

----

954

1095

1223

1348

1467

1583

1694

1801

1904

2003

2099

----

1132

1261

1385

1505

1620

1731

1838

1941

2041

2136

----

1044

1169

1288

1404

1515

1622

1725

1824

1920

2012

2101

906

973

927

994

948

1015

1037

1059

1081

1103

1124

1146

----

970

992

1014

1036

1057

1079

1100

----

Exceeds the BHP limitation.

Unitary Products Group

036-21300-002-A-0905

TABLE 11: SUPPLY AIR BLOWER PERFORMANCE - KEU120 (10 TON)

EXTERNAL STATIC PRESSURE

CFM

0.2

0.4

0.6

0.8

RPM

571

595

619

643

667

692

716

740

765

789

813

837

861

884

907

BHP

0.13

0.37

0.60

0.81

1.01

1.20

1.39

1.57

1.76

1.95

2.14

2.33

2.52

2.72

2.93

RPM

630

654

678

702

726

751

775

799

824

848

872

896

920

943

966

BHP

0.36

0.60

0.82

1.03

1.23

1.43

1.61

1.80

1.99

2.17

2.36

2.55

2.75

2.95

3.15

RPM

682

706

730

754

778

803

827

852

876

900

924

948

972

995

1019

BHP

0.52

0.77

0.99

1.20

1.40

1.59

1.78

1.97

2.15

2.34

2.53

2.72

2.92

3.12

3.32

RPM

733

756

780

804

829

853

877

902

926

950

974

998

1022

1045

1069

BHP

0.66

0.91

1.13

1.34

1.54

1.73

1.92

2.11

2.29

2.48

2.67

2.86

3.05

3.25

3.46

2800

3000

3200

3400

3600

3800

4000

4200

4400

4600

4800

5000

5200

5400

5600

122

332

489

618

349

559

716

845

558

768

925

1054

1249

1435

1614

1790

1963

2136

2310

2486

2665

2847

3033

3224

753

964

1120

1306

1485

1661

1834

2008

2182

2357

2536

2718

2905

3095

939

1149

1329

1504

1678

1851

2025

2201

2380

2562

2748

2939

1119

1294

1468

1641

1815

1991

2169

2352

2538

2728

EXTERNAL STATIC PRESSURE

1.2 1.4

CFM

1.0

1.6

RPM

786

BHP

0.80

1.04

1.27

1.48

1.67

1.87

2.06

2.24

2.43

2.61

2.80

2.99

3.19

3.39

----

RPM

846

BHP

0.96

1.20

1.43

1.64

1.84

2.03

2.22

2.40

2.59

2.77

2.96

3.15

3.35

----

RPM

920

BHP

1.17

1.41

1.64

1.85

2.05

2.24

2.43

2.61

2.80

2.99

3.18

3.37

----

RPM

1010

1034

1057

1082

1106

1130

1155

1179

1203

1228

1252

----

BHP

1.46

1.71

1.93

2.14

2.34

2.53

2.72

2.91

3.09

3.28

3.47

----

2800

3000

3200

3400

3600

3800

4000

4200

4400

4600

4800

5000

5200

5400

5600

744

893

1092

1319

1528

1723

1909

2088

2264

2437

2610

2784

2960

3139

----

1364

1592

1800

1996

2182

2361

2536

2710

2883

3057

3233

----

809

971

870

1121

1329

1525

1711

1890

2066

2239

2412

2586

2762

2941

3123

----

943

833

1180

1375

1561

1741

1916

2090

2263

2437

2613

2791

2973

3160

----

894

967

857

918

991

882

942

1016

1040

1064

1089

1113

1137

1161

1185

----

906

967

930

991

955

1016

1040

1064

1088

1112

1136

----

979

1003

1027

1051

1075

1098

----

Exceeds the BHP limitation.

Unitary Products Group

036-21300-002-A-0905

TABLE 12: SUPPLY AIR BLOWER PERFORMANCE - KEU180 (15 TON)

EXTERNAL STATIC PRESSURE

CFM

0.2

0.4

0.6

0.8

RPM

555

562

569

577

586

595

604

614

624

635

645

656

667

679

690

701

BHP

0.41

0.66

0.89

1.10

1.29

1.47

1.64

1.81

1.97

2.14

2.30

2.46

2.62

2.78

2.95

3.13

RPM

594

600

608

616

624

634

643

653

663

673

684

695

706

717

729

740

BHP

0.67

0.92

1.14

1.35

1.55

1.73

1.90

2.07

2.23

2.39

2.55

2.71

2.87

3.04

3.21

3.38

RPM

633

640

648

656

664

673

683

693

703

713

724

735

746

757

768

780

BHP

0.91

1.16

1.39

1.60

1.79

1.97

2.15

2.31

2.48

2.64

2.80

2.96

3.12

3.29

3.46

3.63

RPM

676

683

690

698

707

716

726

735

745

756

766

777

788

800

811

823

BHP

1.16

1.42

1.64

1.85

2.04

2.23

2.40

2.57

2.73

2.89

3.05

3.21

3.37

3.54

3.71

3.88

4000

4200

4400

4600

4800

5000

5200

5400

5600

5800

6000

6200

6400

6600

6800

7000

382

620

851

1085

1319

1531

1725

1905

2075

2236

2392

2544

2694

2843

2993

3145

3299

3456

3618

616

854

1085

1297

1491

1671

1841

2002

2158

2310

2459

2609

2759

2910

3064

3222

3384

828

1066

1260

1440

1610

1771

1927

2079

2228

2378

2528

2679

2833

2991

3153

1022

1202

1372

1533

1689

1841

1991

2140

2290

2442

2596

2753

2915

EXTERNAL STATIC PRESSURE

1.2 1.4

CFM

1.0

1.6

RPM

723

729

737

745

754

763

772

782

792

802

813

824

835

846

858

869

BHP

1.43

1.68

1.91

2.12

2.31

2.49

2.66

2.83

2.99

3.16

3.32

3.48

3.64

3.80

3.97

4.15

RPM

775

781

789

797

806

815

824

834

844

854

865

876

887

898

910

921

BHP

1.72

1.97

2.20

2.41

2.60

2.78

2.96

3.12

3.29

3.45

3.61

3.77

3.93

4.10

4.26

4.44

RPM

833

840

848

856

864

873

883

893

903

913

924

935

946

957

968

980

BHP

2.05

2.30

2.53

2.74

2.93

3.11

3.28

3.45

3.61

3.77

3.93

4.10

4.26

4.42

4.59

4.77

RPM

900

BHP

2.42

2.67

2.90

3.11

3.30

3.48

3.66

3.82

3.99

4.15

4.31

4.47

4.63

4.80

4.97

5.14

4000

4200

4400

4600

4800

5000

5200

5400

5600

5800

6000

6200

6400

6600

6800

7000

1333

1567

1779

1973

2153

2323

2484

2640

2792

2942

3091

3241

3392

3547

3704

3866

1604

1839

2051

2245

2425

2594

2755

2911

3063

3213

3362

3512

3664

3818

3976

4137

1910

2144

2356

2550

2730

2899

3061

3216

3368

3518

3667

3817

3969

4123

4281

4442

2258

2493

2704

2899

3079

3248

3409

3565

3717

3867

4016

4166

4318

4472

4629

4791

907

915

923

931

940

950

960

970

980

991

1002

1013

1024

1035

1047

Exceeds the BHP limitation.

Unitary Products Group

036-21300-002-A-0905

TABLE 13: STATIC RESISTANCE FOR UNIT ACCESSORIES (IWG) - KEU060-120

Electric Heat KW

Supply Air

Plenum

Return

Air Grill

Hot Water

Coil

Steam

Coil

CFM

2200

2400

2600

2800

3000

3200

3400

3600

3800

4000

4200

4400

4600

4800

5000

0.01

0.02

0.03

0.04

0.01

0.02

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.12

0.13

0.14

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.12

0.14

0.15

0.16

0.18

0.19

0.21

0.02

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.02

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.07

0.09

0.10

0.12

0.14

0.16

0.17

0.19

0.22

0.24

0.26

0.28

0.31

0.33

0.36

0.11

0.13

0.15

0.16

0.18

0.20

0.23

0.25

0.27

0.30

0.33

0.36

0.39

0.43

0.46

TABLE 14: STATIC RESISTANCE FOR UNIT ACCESSORIES (IWG) - KEU180

Electric Heat KW

Supply Air

Plenum

Return

Air Grill

Hot Water

Coil

Steam

Coil

CFM

4600

4800

5000

5200

5400

5600

5800

6000

6200

6400

6600

6800

7000

7200

7400

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.08

0.09

0.10

0.11

0.12

0.13

0.14

0.15

0.16

0.17

0.12

0.13

0.14

0.16

0.17

0.18

0.20

0.21

0.22

0.24

0.25

0.27

0.29

0.30

0.32

0.18

0.19

0.21

0.23

0.24

0.26

0.28

0.30

0.32

0.34

0.36

0.38

0.41

0.43

0.45

0.23

0.25

0.27

0.29

0.31

0.34

0.37

0.40

0.43

0.47

0.51

0.55

0.59

0.64

0.68

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.31

0.33

0.36

0.38

0.41

0.44

0.47

0.50

0.53

0.56

0.59

0.62

0.66

0.69

0.73

0.39

0.43

0.46

0.50

0.54

0.58

0.62

0.66

0.71

0.75

0.80

0.85

0.90

0.95

1.01

Unitary Products Group

036-21300-002-A-0905

TABLE 15: SUPPLY AIR PLENUM PERFORMANCE DATA

Angle of Deflection

Vertical

Horizontal

Vertical

Louvers

(Plan

Horizontal

Vertical

Louvers

(Plan

Horizontal

Louvers

(Elevation

View)

Louvers

(Elevation

View)

Louvers

(Plan

Louvers

(Elevation

View)

Face

Model CFM Velocity

(FPM)

View)

Spread

Throw

(Feet)

Throw

(Feet)

Spread

(Feet)

Throw

(Feet)

Spread

(Feet)

18˚

Min. Max. Min. Max

Min.

Max Min. Max

Drop (Feet)

Min. Max. Min. Max.

Drop (Feet)

1600

1800

2000

2200

2400

2700

3000

3300

3600

3200

3600

4000

4400

4800

5400

6000

6600

7200

630

710

106

116

126

107

060

090

120

180

790

870

940

615

690

770

845

101

110

920

820

920

110

123

135

147

132

149

165

182

199

1025

1130

1230

880

102

115

127

112

124

138

152

106

1000

1110

1220

1330

107

119

131

143

109 166

1. Adjusting the vertical louvers will vary the throw, the spread and the drop.

2. Adjusting the horizontal louvers will only vary the drop.

3. The velocity of the air will be 125 ft./min. at the minimum distance and 80 ft./min. at the maximum distance.

4. The velocity of the conditioned air at the bottom of the drop will be 50 ft./min. Drafts will occur if the drop extends into the occupied

level of the conditioned space.

TABLE 16: BLOWER MOTOR AND DRIVE DATA

MOTOR

ADJUSTABLE MOTOR PULLEY

FIXED BLOWER PULLEY

OUTSIDE PITCH

BELT (NOTCHED)

PITCH

BLOWER

RANGE

(RPM)

OUTSIDE PITCH

MODEL

DESIG-

NATION

BORE DESIG-

(IN.)

FRAME

DIA.

(IN.)

DIA.

(IN.)

DIA.

(IN.)

DIA.

(IN.)

LENGTH QTY.

(IN.)

NATION

060

090

120

180

810/1110

655/880

700/950

625/810

3/4

1-1/2

1VL44

1VM50

3.1-4.1

2.1-4.1

3.1-4.1

3.7-4.7

2.8-3.8

3.4-4.4

5/8

7/8

AL64

AK79

BK80

BK105

6.2

7.9

7.4

9.9

5.8

7.5

7.0

9.5

3/4

A32

A36

A57

33.3

37.3

58.3

Unitary Products Group

036-21300-002-A-0905

TABLE 17: KEU PHYSICAL DATA

Model

Component

Description

060

090

120

180

Centrifugal Blower (Dia. X Wd. in.)

15 X 15

18 X 18

EVAPORATOR

BLOWER¹

Fan Motor HP (Belt Drive)

Rows Deep

3/4

1-1/2

Finned Length (in.)

Fins per Inch

EVAPORATOR

COIL

Face Area (ft.²)

5.0

8.6

10.2

12.1

Rows Deep

Finned Length (in.)

Fins Per Inch

Face Area (ft.²)

HOT WATER COIL

3.8

5.4

9.0

Inlet Connection

1” NPTE

1-3/8” O.D

Outlet Connection

Rows Deep

1” NPTE

1-3/8” O.D

Finned Length (in.)

Fins Per Inch

STEAM COIL

Face Area (ft.²)

3.8

5.4

9.0

Inlet Connection

1-1/2” NPTE

Outlet Connection

Quantity Per Unit (16” X 25” X 1”)

Quantity Per Unit (20” X 20” X 1”)

Total Face Area (ft.²)

Refrigerant 22 (lbs./oz.)

1-1/2” NPTE

AIR FILTERS

5.6

0/7

11.1

0/7

11.1

0/10

16.7

0/0

HOLDING CHARGE

1. Refer to Blower Motor and Drive Data table for additional blower and drive information.

All of these 1750 RPM motors are solid base, 56 frame with 1.15 service factor, inherent protection and permanently lubricated ball bearings.

Unitary Products Group

036-21300-002-A-0905

ꢋꢄꢌꢎ (/,% 7ꢄ"53().'

). 2%!2 0!.%,

ꢆ&OR ,OW 6OLTAGE

#ONTROL 0ANEL

ꢀꢈꢂꢃꢄꢌ

ꢃꢀꢂꢃꢄꢁ

ꢌꢂꢃꢄꢅ

ꢋꢄꢌꢎ +./#+/54

). 2%!2 0!.%,

ꢆ&OR 0OWER 7IRING

ꢃꢂꢅꢀꢄꢀꢅ +./#+/54

ꢆ2EMOVED ONLY WHEN

%LECTRIC (EAT !CCESSORY

IS USED

!)2

/54

ꢀꢂꢋꢄꢌ

ꢃ

ꢁꢂꢃꢄꢅ

ꢀꢄꢁ

ꢃꢃꢂꢃꢄꢅ

ꢅꢅꢂꢀꢄꢁ

ꢅꢂꢃꢄꢁ

ꢃꢃꢂꢏꢄꢌ

ꢅꢂꢏꢄꢃꢈ

",/7%2 -/4/2

!.$ $2)6%

!##%33 0!.%,

ꢆ4HIS SIDE INLY

&),4%2 !##%33

0!.%,ꢆ4HIS

SIDE ONLY

ꢁꢀꢂꢃꢄꢌ

All dimensions are in inches. They are

subject to change without notice. Certi-

fied dimensions will be provided upon

request.

(/,% 7)4( '2/-ꢂ

-%4 &/2 ꢀꢄꢌ /ꢐ$ꢐ

,)15)$ ,).%

ꢅꢇ

ꢀꢂꢋꢄꢌ

(/,% 7)4( '2/-ꢂ

-%4 &/2 ꢋꢄꢌ /ꢐ$ꢐ

35#4)/. ,).%

ꢃꢂꢏꢄꢌ

ꢅ

ꢃꢂꢀꢄꢌ

ꢃꢂꢀꢄꢃꢈ

ꢃꢇꢂꢀꢄꢌ

ꢃꢂꢃꢄꢌ

!)2

ꢅ

ꢅꢅ

ꢋꢄꢌ /ꢐ$ꢐ $2!).

#/..ꢐ ꢆ-UST BE

TRAPPED

ꢀꢅ

ꢅ

FIGURE 1 - UNIT DIMENSIONS KEU060

ACCESSORIES

1. Overall dimensions of the unit will vary if an electric

heater, a supply air plenum or a base is used.

2. This dimension is required for removal of the coil. Only

26” is required for normal service.

•

ELECTRIC HEATER - Add 13” to unit height when used.

SUPPLY AIR PLENUM - Add 24-1/4” to unit height when used.

BASE - Add 20” to unit height when used.

3. Although no clearance is required for service and oper-

ation, some clearance may be required for routing the

power and control wiring.

4. Allow enough clearance to trap the condensate drain

line.

TABLE 18: UNIT CLEARANCES KEU060

MINIMUM CLEARANCES

060

24”

Side with RETURN AIR opening

Side with SUPPLY AIR opening¹

Side with PIPING CONNECTIONS²

36”

12”

Side opposite with PIPING CONNECTIONS

Side with access for both POWER & CONTROL

WIRING^3,

Bottom⁴

Unitary Products Group

036-21300-002-A-0905

ꢃꢂꢀꢄꢌꢎ +./#+/54

&/2 0/7%2 7)2).' ꢆ"ACK 0ANEL

$O NOT REMOVE THIS KNOCKOUT WHEN

THE UNIT IS EQUIPPED WITH AN %LECTRIC

(EAT !CCESSORYꢐ 2EFER TO DETAIL OF

THE (EATER !CCESSORY FOR POWER

WIRING ACCESS OPENING

ꢏꢅꢂꢃꢄꢁ

ꢃꢌꢂꢋꢄꢌ

ꢋꢄꢌꢎ (/,% 7ꢄ"53().'

&/2 #/.42/,

7)2).'

ꢃꢏꢂꢀꢄꢌ

ꢆ"ACK 0ANEL

ꢃꢂꢅꢀꢄꢀꢅ +./#+/54

ꢆ2EMOVED ONLY WHEN

%LECTRIC (EAT !CCESSORY

IS USED

!)2

/54

ꢀꢂꢏꢄꢌ

ꢁꢂꢃꢄꢁ

ꢃ

ꢈꢂꢀꢄꢁ

ꢏꢄꢌ

ꢃꢈꢂꢃꢄꢌ

ꢅꢂꢃꢄꢁ

ꢅꢏꢂꢋꢄꢌ

ꢃꢏ

",/7%2 -/4/2

!.$ $2)6%

!##%33 0!.%,

ꢆ4HIS SIDE ONLY

(/,% 7)4( '2/-ꢂ

-%4 &/2 ꢃꢄꢅ /ꢐ$ꢐ

,)15)$ ,).%

All dimensions are in inches. They are

subject to change without notice. Certi-

fied dimensions will be provided upon

request.

ꢏꢃꢂꢃꢄꢌ

ꢅꢀ

ꢁ

(/,% 7)4( '2/-ꢂ

-%4 &/2 ꢃꢂꢃꢄꢌ /ꢐ$ꢐ

35#4)/. ,).%

ꢌꢂꢀꢄꢌ

ꢃꢂꢏꢄꢌ

ꢅꢂꢏꢄꢌ

ꢀꢂꢃꢄꢁ

ꢃꢂꢀꢄꢌ

ꢃꢂꢀꢄꢁ

!)2

ꢅ

ꢃꢂꢃꢄꢌ

ꢋꢄꢌ /ꢐ$ꢐ $2!).

#/..ꢐ ꢆ-UST BE

TRAPPED

ꢅꢏꢂꢃꢄꢌ

ꢅ

ꢁꢌ

ꢃ

&),4%2 !##%33 0!.%,

ꢆ7HEN UNIT IS INSTALLED IN

A HORIZONTAL POSITIONꢊDO

NOT BLOCK THIS AREA WITH

REFRIGERANT PIPING

FIGURE 2 - UNIT DIMENSIONS KEU090 & 120

ACCESSORIES

1. Overall dimensions of the unit will vary if an electric

heater, a supply air plenum or a base is used.

2. This dimension is required for removal of the coil. Only

26” is required for normal service.

•

ELECTRIC HEATER - Add 14-1/4” to unit height when used.

SUPPLY AIR PLENUM - Add 27-1/2” to unit height when used.

BASE - Add 20” to unit height when used.

3. Although no clearance is required for service and oper-

ation, some clearance may be required for routing the

power and control wiring.

TABLE 19: UNIT CLEARANCES KEU090 & 120

MINIMUM CLEARANCES

Side with RETURN AIR opening

090-120

4. Allow enough clearance to trap the condensate drain

line.

24”

36”

12”

Side with SUPPLY AIR opening¹

Side with PIPING CONNECTIONS²

Side opposite with PIPING CONNECTIONS

Side with access for both POWER & CONTROL

WIRING^3,

Bottom⁴

Unitary Products Group

036-21300-002-A-0905

(

)

All dimensions are in inches. They are

subject to change without notice. Certi-

fied dimensions will be provided upon

request.

(

)

FIGURE 3 - UNIT DIMENSIONS KEU180

ACCESSORIES

1. Overall dimension of the unit will vary if an electric

heater, a supply air plenum or a base is used.

2. This dimension is required for removal of the DX coil.

Only 26” is required for normal servicing.

3. If the coil has to be removed, this dimension is required

to loosen screws that secure the coil to the unit frame.

This dimension will also be required for blower motor

access if the piping connections are made on the oppo-

site side of the unit.

•

ELECTRIC HEATER - Add 14-1/4” to unit height when using 10,

16, 26, or 36 KW heater

•

SUPPLY AIR PLENUM - Add 27” to unit height when used.

BASE - Add 24” to unit height when used.

HOT WATER OR STEAM COIL - Add 6” to unit depth when used.

TABLE 20: UNIT CLEARANCES KEU180

MINIMUM CLEARANCES

180

24”

4. Allow enough clearance to trap the condensate drain

lines.

Side Air with RETURN AIR opening

Side with SUPPLY AIR opening¹

Side with PIPING CONNECTIONS²

Side opposite PIPING CONNECTIONS³

Bottom⁴

61”

26”

Unitary Products Group

036-21300-002-A-0905

6833/<ꢃ$,5ꢃ3/(180

ꢅ

(

)

ꢍꢍꢉꢍꢈꢆ

ꢍꢉꢍꢈꢆ

ꢈ63ꢀꢄꢉꢌ

ꢈ63ꢀꢄꢉꢈ

ꢈꢍꢀꢃꢅꢃ.12&.2876ꢃ)25ꢃ32:(5ꢃ ꢃ&21752/ꢃ:,5,1*

6+,33('ꢁ.12&.('ꢉ'2:1

ꢁꢁꢁ)25ꢁ),(/'ꢁ$66(0%/<

WITH ELECTRIC HEAT - Remove this 2-1/2” knockout and one of the 7/8”

knockouts from the rear panel of the plenum. Remove the 1-23/32” knockout

and one of the 7/8” knockouts from the top panel of the basic unit. Install a 1/

2” squeeze connector in both of the 7/8” openings.

ꢀꢊꢀꢋꢃꢀꢁꢀꢋꢃꢈꢌꢀꢃꢅꢃ.12&.287ꢃ)25ꢃ32:(5ꢃ:,5,1*

WITH ELECTRIC HEAT - Remove this 2-1/2” knockout from the

rear panel of the plenum. Route the power wiring conduit through

this opening and connect it to the field-supplied fitting on the elec-

tric heat accessory. Connect the power wiring to the fuse block in

the heater control box.

Route the power wiring conduit through the 2-1/2” opening and connect it

to the field-supplied fitting on the electric heat accessory. Connect the

power wiring to the fuse block in the heater control box.

Route the control wires through the 7/8” openings and connect them to

the terminals on block TB1. Secure them with the 1/2” squeeze connec-

tors.

Install the control wiring per basic unit Installation Manual.

DO NOT route any field control wiring through the plenum.

Electric Heaters are NOT CSA approved for installation

within a supply air plenum.

Electric Heaters are NOT CSA approved for installation

within a supply air plenum.

WITHOUT ELECTRIC HEAT - Remove both 7/8” knockouts from the rear

panel of the plenum and both 7/8” knockouts from the top panel of the

basic unit. Install a 1/2” squeeze connector in one of the plenum open-

ings and both of the unit openings. Install a 1/2” conduit fitting in the other

opening of the plenum.

WITHOUT ELECTRIC HEAT - Install the power and the control wiring

per basic unit Installation Manual. DO NOT route any wiring through

the plenum and DO NOT remove this knockout.

Connect the power wiring conduit to the fitting on the plenum. Route the

power wiring through the conduit, one of the squeeze connectors on the

unit, and the field-supplied squeeze connector on the blower motor contac-

tor box. Connect the power wiring to the blower motor contactor.

Plenum Dimensions (inches)

Plenum Unit

Model Model

1SP0450 060

36 25-1/2 34-2/8 31-3/4 15-3/4 7-5/8 7/8 2-1/8 11-1/4

090

1SP0451

120

52-1/8 28-1/4 27-1/2 49-3/8 17-7/8 8-3/4 7/8 1-1/8 15-1/4 1-3/4

Route the control wires through the remaining plenum and unit open-

ings and connect them to the terminals on block TB1. Secure them

with the 1/2” squeeze connectors.

1SP0452 180 60-3/4 31

27 55-3/4 19-7/8 6-1/8 1- 2-1/2 19-1/2 1-3/4

ꢍ

(

)

$&&(66ꢁ23(1,1*ꢁ)25ꢁ32:(5ꢁ6833/<ꢁ:,5,1*

ꢍꢂ.:ꢁ7+58ꢁꢅꢃ.:ꢁꢉꢁ$GGꢁDꢁꢍꢉꢍꢈꢀꢑꢁFRQGXLWꢁILWWLQJ

ꢁꢁꢁWRꢁWKHꢁꢍꢉꢆꢅꢈꢅꢆꢑꢁKROHꢁIRUꢁZLUHꢁVL]HVꢁXSꢁWKURXJK

ꢁꢁꢁꢓꢍꢁ$:*ꢋꢁꢁ5HPRYHꢁWKHꢁNQRFNRXWꢁULQJꢁDQGꢁDGGꢁD

ꢁꢁꢁꢍꢉꢍꢈꢆꢑꢁFRQGXLWꢁILWWLQJꢁWRꢁWKHꢁꢍꢉꢅꢍꢈꢅꢆꢑꢁKROHꢁIRU

ꢁꢁꢁZLUHꢁVL]HVꢁXSꢁWKURXJKꢁꢓꢂꢁ$:*ꢋ

+($7(5

(/(0(17

&+$0%(5

ꢌꢆ.:ꢁ7+58ꢁꢅꢃ.:ꢁꢉꢁ$GGꢁDꢁꢍꢉꢍꢈꢀꢑꢁFRQGXLWꢁILWWLQJ

ꢁꢁꢁWRꢁWKHꢁꢍꢉꢆꢅꢈꢅꢆꢑꢁKROHꢁIRUꢁZLUHꢁVL]HVꢁXSꢁWKURXJK

ꢁꢁꢁꢓꢍꢁ$:*ꢋꢁꢁ5HPRYHꢁWKHꢁNQRFNRXWꢁULQJꢁDQGꢁDGGꢁD

ꢁꢁꢁꢆ ꢑꢁFRQGXLWꢁILWWLQJꢁWRꢁWKHꢁꢆꢉꢍꢈꢆꢑꢁKROHꢁIRUꢁZLUHꢁVL]HV

ꢁꢁꢁXSꢁWKURXJKꢁꢓꢂꢂꢁ ꢂꢂ $:*ꢋ

ꢅꢈꢀ

&21752/ꢁ%2;

$&&(66ꢁ3$1(/

ꢍꢈꢆ

:,5,1*ꢁ+$51(66ꢁ/2&$7,21

7KLVꢁRSHQLQJꢁLQꢁWKHꢁERWWRPꢁRIꢁWKHꢁKHDWHU

FRQWUROꢁER[ꢁLVꢁXVHGꢁIRUꢁWKHꢁZLULQJꢁKDUQHVV

WKDWꢁFRQQHFWVꢁWKHꢁKHDWHUꢁDFFHVVRU\ꢁWRꢁWKH

EDVLFꢁXQLWꢋꢁꢁ,WꢁLVꢁSURYLGHGꢁZLWKꢁDꢁVTXHH]H

FRQQHFWRUꢁIRUꢁVHFXULQJꢁWKHꢁZLULQJꢁKDUQHVVꢊ

DQGꢁLWVꢁORFDWLRQꢁFRUUHVSRQGVꢁWRꢁWKHꢁORFDꢉ

WLRQꢁRIꢁWKHꢁꢍꢉꢆꢅꢈꢅꢆꢑꢁNQRFNRXWꢁLQꢁWKHꢁWRS

SDQHOꢁRIꢁWKHꢁEDVLFꢁXQLWꢋ

FIGURE 5 - ACCESSORY DIMENSIONS

Unitary Products Group

036-21300-002-A-0905

TABLE 21: ELECTRIC HEATER DIMENSIONS KEU060, 090, 120 & 180

Heater Dimensions (inches)

Heater

Model

Nom.

Unit

Model

2HT04501025¹

2HT04501625¹

2HT04502625¹

060

25-1/8 22-1/2

7/8

1/2 5-1/4 1-11/16 1-3/4 20-1/8 16-7/8

2HS04501025, 46, 58

2HS04501625, 46, 58

2HS04502625, 46, 58

2HS04503625, 46, 58

090

120

180

27-1/4 25-1/4 14-1/4

1/2 5-1/2

1-1/2

2-1/4

1-1/2 22-1/4 19-1/4

2-1/2 22-1/4 19-1/4

2HS04507225, 46, 58

180

29-7/8 26-3/8 21-3/4 2-3/8 5-1/4 3/4 6-3/8

1. The 2HT heaters are not CSA approved for 060 units mounted horizontally.

RETURN AIR GRILLE

5/8

FIGURE 7 - BASE ACCESSORY

FIGURE 6 - RETURN AIR GRILL

Grill Dimensions (Inches)

Grill Model

Unit Model

Grill Model

Unit Model

1BS0450

1BS0451

1BS0452

060

1RG0450

1RG0451

1RG0452

060

090

120

090

120

25-1/8

31-5/8

180

60-3/4

180

60-3/4

Unitary Products Group

036-21300-002-A-0905

1-1/2" NPTE

CONNS.

Steam Coil Dimensions (inches)

Coil

Model

Unit

Model

21-7/8

060

090

120

180

2-1/2

2-5/8 10-5/8

2-5/8 13-5/8

1NF0450

1NF0451

60-3/4 32-1/4

3-5/16 3-1/2 17-1/2

1NF0452

1. Installs over the return air opening of the unit-before the filters.

2. Installs between the coil and blower section of the unit.

FIGURE 8 - STEAM COIL

Hot Water Coil Dimensions (inches)

Coil

Unit

Model

1”

NPTE

ꢍ³ꢁ137(

&211¶6ꢋ

060

090

120

36 21-7/8

1-11/16 2-3/4 6-1/4 3-3/8

1-11/16 2-3/4 5-7/8 3-3/8

2-5/32 3-5/16 6-9/16 3-27/32

1HW0450

ꢆ

1”

NPTE

1HW0451

1”

NPTE

)

(

1HW0451

1-3/8

NPTE

180 60-3/4 32-1/4

1HW0452

1. Installs over the return air opening of the unit-before the filters.

2. Installs between the coil and blower section of the unit.

ꢆ

FIGURE 9 - HOT WATER COIL

Unitary Products Group

036-21300-002-A-0905

TABLE 22: KEU ELECTRICAL DATA

Min.

Max. Fuse¹/

Power

Supply

Voltage

Indoor

Motor

FLA

Heater

Model

Number

Nominal

Heater

Model

(TONS)

Applied

Heater KW

Electric

Heat Amps

Circuit

Ampacity

(AMPS)

9.5

HACR

Breaker²

(AMPS)

None

2HT04501025

2HT04501625

2HT04502625

None

7.5

20.8

33.4

54.2

35.6

51.2

77.3

8.6

208

240

7.6

6.9

12.0

19.5

060

(5)

2HT04501025

2HT04501625

2HT04502625

None

10.0

16.0

26.0

24.1

38.5

62.5

38.7

56.7

86.8

8.3

2HS04501025

2HS04501625

2HS04502625

2HS04503625

None

7.5

20.8

33.4

54.2

75.1

34.3

49.9

76.0

102.1

7.5

208

240

460

575

208

240

460

575

6.6

6.0

3.0

2.4

7.5

6.8

3.4

2.7

12.0

19.5

27.0

110

2HS04501025

2HS04501625

2HS04502625

2HS04503625

None

10.0

16.0

26.0

36.0

24.1

38.5

62.5

86.6

37.6

55.6

85.7

115.8

3.8

125

090

(7.5)

2HS04501046

2HS04501646

2HS04502646

2HS04503646

None

10.0

16.0

26.0

36.0

12.0

19.2

31.3

43.3

18.8

27.8

42.8

57.9

3.0

2HS04501058

2HS04501658

2HS04502658

2HS04503658

None

10.0

16.0

26.0

36.0

9.6

15.0

22.2

34.3

46.3

9.4

15.4

25.0

34.6

2HS04501025

2HS04501625

2HS04502625

2HS04503625

None

7.5

20.8

33.4

54.2

75.1

35.4

51.1

77.1

103.2

8.5

12.0

19.5

27.0

110

2HS04501025

2HS04501625

2HS04502625

2HS04503625

None

10.0

16.0

26.0

36.0

24.1

38.5

62.5

86.6

38.6

56.6

86.7

116.8

4.3

125

120

(10)

2HS04501046

2HS04501646

2HS04502646

2HS04503646

None

10.0

16.0

26.0

36.0

12.0

19.2

31.3

43.3

19.3

28.3

43.3

58.4

3.4

2HS04501058

2HS04501658

2HS04502658

2HS04503658

10.0

16.0

26.0

36.0

9.6

15.4

22.6

34.6

46.7

15.4

25.0

34.6

Unitary Products Group

036-21300-002-A-0905

TABLE 22: KEU ELECTRICAL DATA (CONTINUED)

Min.

Circuit

Ampacity

(AMPS)

13.3

Max. Fuse¹/

Power

Supply

Voltage

Indoor

Motor

FLA

Heater

Model

Number

Nominal

Heater

Model

(TONS)

Applied

Heater KW

Electric

Heat Amps

HACR

Breaker²

(AMPS)

None

2HS04501025

2HS04501625

2HS04502625

2HS04503625

2HS04507225

None

7.5

20.8

33.4

54.2

75.1

150.1

39.3

12.0

19.5

27.0

54.1

54.9

208

240

460

575

10.6

9.6

81.0

107.1

200.9

12.0

110

225

2HS04501025

2HS04501625

2HS04502625

2HS04503625

2HS04507225

None

10.0

16.0

26.0

36.0

72.0

24.1

38.5

62.5

86.6

173.2

42.1

60.1

90.2

100

125

250

120.3

228.5

6.0

180

(15)

2HS04501046

2HS04501646

2HS04502646

2HS04503646

2HS04507246

None

10.0

16.0

26.0

36.0

72.0

12.0

19.2

31.3

43.3

86.6

21.0

30.1

4.8

45.1

60.1

114.3

4.9

125

2HS04501058

2HS04501658

2HS04502658

2HS04503658

2HS04507258

10.0

16.0

26.0

36.0

72.0

9.6

16.9

15.4

25.0

34.6

69.3

24.1

3.9

36.1

48.2

91.5

100

1. Dual element time delay.

2. HACR type per NEC.

3. The K*EU060 indoor motor is single phase. The electrical heaters MUST be supplied with 3-phase voltage only.

Unitary Products Group

036-21300-002-A-0905

COOLING ONLY UNITS AND UNITS WITH

UNITS WITH ELECTRIC HEAT ACCESSORY

STEAM OR HOT WATER COIL ACCESSORY

3-PHASE

LINE VOLTAGE

POWER SUPPLY

POWER WIRING,

DESCONNECT

SWITCH

AND FUSING

(OR CIRCUIT

BREAKER)

LINE VOLTAGE

POWER SUPPLY

POWER WIRING,

TERMINALS ON

SUPPLY AIR

BLOWER MOTOR

TERMINALS

ON FUSE HOLDER

IN ELECTRIC HEAR

CONTROL BOX

DESCONNECT SWITCH

AND FUSING TO BE

SUPPLIED BY FIELD

CONTACTOR

10M

GROUND LUG

IN ELECTRIC HEAT

CONTROL BOX

TO BE SUPPLIED

BY FIELD

GROUND

SCREW

NOTE: USE COPPER

CONDUCTORS ONLY

*Not required on 060 (1-Phase

only) All other units are 3-Phase.

WIRE IN ACCORDANCE WITH LOCAL

AND NATIONAL ELECTRICAL CODES

FIGURE 10 - FIELD WIRING FOR POWER SUPPLY

COOLING ONLY UNITS

2-STAGE COOLING FOR HCA180/KEU180**

1-STAGE COOLING

COND.

UNIT

COND.

UNIT

24-VOLT

CONTROL

WIRING

24-VOLT

CONTROL

WIRING

TERMINALS ON

THERMOSTAT 6TH13700724

WITH SUB-BASE 2TB08700124

TERMINALS ON

THERMOSTAT 6TH04701724

WITH SUB-BASE 2TB04700124

TERMINAL

BLOCK 4TB

ON BLOWER UNIT

TERMINAL BLOCK 4TB

ON BLOWER UNIT

FIGURE 11 - COOLING ONLY UNIT

UNITS WITH STEAM OR HOT WATER COIL ACCESSORY

1-STAGE COOLING

24-VOLT CONTROL WIRING

2-STAGE COOLING FOR HCA180/KEU180**

24-VOLT CONTROL WIRING

COND.

UNIT

COND.

UNIT

TERMINALS ON

THERMOSTAT

6TH04701524

WITH SUB-BASE

2TB04700324

TO HEATER COIL

CONTROL CIRCUIT

TERMINAL

BLOCK 4TB

ON BLOWER UNIT

TERMINAL

BLOCK 4TB

ON BLOWER UNIT

TO HEATER COIL

CONTROL CIRCUIT

TERMINALS ON THERMOSTAT 6TH13700724

WITH SUB-BASE 2TB17700324

FIGURE 12 - UNIT WITH STEAM OR HOT WATER COIL ACCESSORY

Unitary Products Group

036-21300-002-A-0905

(

)

FIGURE 13 - FIELD WIRING FOR UNITS WITH ELECTRIC HEAT

Unitary Products Group

036-21300-002-A-0905

Unitary Products Group

036-21300-002-A-0905

Unitary Products Group

Subject to change without notice. Printed in U.S.A.

036-21300-002-A-0905

Supersedes: 036-21300-001-A-0901

Unitary

Products

Group

5005

York

Drive

Norman

73069

Whirlpool Acd052pk0 User Manual
Toshiba Ras 13uav E2 User Manual
Roberts Gorden Uha Series 150 User Manual
Mitsubishi 4g9 User Manual
Linak 00ch01eu 00 User Manual
JENSEN JE2411 User Manual
DELL XPS L321X User Manual
CRAFTSMAN 172.417700 User Manual
CANON POWERSHOT SD1100 IS User Manual
BLACK DECKER HEDGE HOG HS1010 User Manual