Trane Uh Prc001 En User Manual

Propeller Unit  
Heaters/Unitary  
17.4 to 705.6 MBh  
Two Versatile Models -Various Sizes  
Easy Installation  
October 1999  
UH-PRC001-EN  
Contents  
Introduction  
2
4
Features and Benefits  
Application Considerations  
Selection Procedure  
8
11  
Manual Selection Procedure  
Model Number Description  
19  
21  
Performance Data  
23  
44  
47  
50  
Electric Power  
Dimension and Weights  
Mechanical Specifications  
UH-PRC001-EN  
3
Features and  
Benefits  
Trane propeller unit heaters feature the  
largest selection of standard sizes from  
any line in the industry. In fact, vertical  
Model P and horizontal Model S unit  
heaters provide enough off-the-shelf’  
selections to fit almost any application.  
The versatile two-in-one Model P is  
available in 15 sizes with capacities from  
41.3 MBh to 705.6 MBh while the  
S is available in 29 sizes with the  
capacities from 17.4 MBh up to 404 MBh.  
Both are designed for durability,  
attractiveness and compactness.These  
features combined with economical  
operation, give strategically sized Trane  
unit heaters an edge unmatched by any  
other manufacturer.  
companion standard and bypass Model  
The Space-Saving Model S  
Two Units in One – the Versatile Model P  
TheTrane Model P can be quickly field  
converted from standard to low final  
temperature PL design simply by  
Put Heat Where Its Needed  
Exclusive louver fin diffusers featured on  
Trane unit heaters put heat where its  
needed.  
The Model S features attractive,  
functional styling in a space-saving,  
compact design.  
In addition,Trane offers an exclusive  
bypass Model S design to meet low final  
temperature, high cfm requirements.This  
design uses a modified coil which allows  
some of the air to flow over the top of the  
coil without being heated.This cooler  
band of air prevents the heated air from  
rising so warm air throw is increased  
while efficiency is improved.  
removing the units patented knockout  
air ports.This unique two-in-one design  
allows the stocking wholesaler to cut  
inventories in half and still meet most  
customer application requirements.  
These patentedTrane diffusers provide  
an unlimited combination of air diffusion  
patterns as well as greater air throw  
distance. In fact, when the louver cone  
diffuser is added to the Model P, up to 45  
percent greater air throw distance is  
possible.  
Patented Trane louver cone diffusers allow  
directional flexibility of heated air.  
On Model S units, the combination of  
horizontal louver blades and patented  
vertical diffuser fins provide four-  
directional control of air delivery.  
Optional low cost louver fin diffusers can  
be adjusted to provide up to 25 percent  
more air throw.  
Trane Model S features louvered discharge as  
standard.  
4
UH-PRC001-EN  
Features and  
Benefits  
The Model S Coil  
Compact Design  
The Model S unit heater features a  
unique single tube serpentine coil.This  
compact, efficient coil has piping  
connections at the back for added space  
savings, convenience and appearance.  
Model S single circuit coils use threaded  
connectors at the back of the unit.  
Trane designed Model S and P propeller  
unit heaters for easy installation and low  
maintenance.TheTrane Sigma-Flo® fin  
design allows coil size to be reduced  
while maintaining high capacity  
performance equal to larger flat-fin coils.  
Reduced size and weight makesTrane  
unit heaters easy to handle and install.  
The Model P Motor  
Rectangular Draw-Thru Coils  
The Model P motor is mounted below  
the top panel inside the heater casing.  
This reduces unit height and permits the  
unit to be installed closer to the ceiling  
for added headroom.  
The Model P draw-thru coils use short  
lengths of steel pipe threaded for supply  
and return connections.These features  
make piping connections much easier  
for the installer.  
UH-PRC001-EN  
5
Features and  
Benefits  
Model P  
A
ExclusiveTrane designed aluminum fans  
provide smooth, nonsurge performance.  
This, in turn, provides efficient, quiet  
operation.  
C
D
G
F
B
High performance Sigma-Flo® fins in a  
one-row coil have more efficient heat  
transfer characteristics than flat fin coils.  
B
C
Steel pipe headers are electrically  
induction-brazed to coil tubes.  
E
D
A
Top panel features knockout air ports  
that, when removed, convert the unit  
from standard to low final air  
temperature, higher cfm operation.  
E
Bottom plate provides drawn fan orifice  
to assure smooth airflow.  
F
Model S  
A
Exclusive, compact one-row  
serpentine coil features high  
performance Sigma-Flo fins.  
Sturdy motor mounts absorb vibration  
and anchor the motor securely.  
G
Totally enclosed industrial designed  
motors feature built-in overload  
protection.  
B
One-piece wraparound casing with  
picture-frame front panel combines  
attractiveness with durability.  
B
C
C
Heavy-gauge, one-piece back panel  
can be easily removed for quick coil  
access.  
G
A
E
D
Rear connections and a compact  
design provide more headroom than  
conventional units.  
H
E
Sturdy fan guard provides stronger  
motor mount and quiet operation.  
F
Unique coil supports anchor coil  
F
D
tubes without restricting expansion.  
G
Trane horizontal louvers stay in  
position with the exclusive louver  
keeper design.  
H
Totally enclosed industrial design  
motors feature built-in overload  
protection.  
6
UH-PRC001-EN  
Features and  
Benefits  
Model P  
Simple Hanger and Piping Connections  
The Model P uses weldnut type hanger  
connections, while the Model S uses a  
nutsert type hanger connection. Hanger  
rods screw easily into threaded anchor  
points. Piping connections can be made  
equally as easy. Model P units provide  
threaded connections for inlet and outlet,  
top and bottom.  
Fully Accessible for Easy Maintenance  
Model S and P unit heaters are fully  
accessible for maintenance. Only four  
main bolts are needed to disassemble  
the Model P. And when quick access is  
needed, the Model S features a  
one-piece back that can be easily  
removed and slid over pipes without  
breaking connections.  
External Couplings  
The Model S provides threaded  
connections for supply and return on the  
back of its casing. In addition, back  
connections reduce the amount of space  
needed for installation.  
Model S  
Motors can also be easily removed. Both  
units feature totally enclosed motors  
with thermal overload protection. As an  
added benefit, Model P fan-motor  
assemblies can be conveniently  
removed from below through the fan  
outlet.  
UH-PRC001-EN  
7
Application  
Considerations  
General Rules  
In locating or spottingTrane Propeller  
Unit Heaters – either the Model S  
Horizontal or Model P Projection Unit  
Heater – the following general rules  
should be considered.  
1. Spot units at points of greatest heat  
loss. Blanket outside doorways  
effectively and provide ample coverage  
for exposed window areas.  
2. Units, especially in the case of the  
Model S Horizontal Unit Heater, should  
be arranged to blow toward or along  
exposed walls, preferably striking the  
wall at a slight angle so that the heated  
air exerts a wiping effect along the wall.  
Balance of units required to supply Btu  
requirements should be spaced  
strategically in balance of the area.  
3. Unit heaters should be arranged to  
blow into open spaces such as aisles and  
not directly at any worker. An exception  
to this rule involves the use of the Model  
P Unit Heater equipped with the Louver  
Cone Diffuser.This combination can be  
used effectively over closely spaced bins  
or machines without regard for open  
space. But not even the Model P Unit  
Heater with Louver Cone Diffuser should  
be in such close proximity to the workers  
to cause discomfort.  
4.TheTrane solid-state speed control will  
provide maximum capacity flexibility and  
quieter operation. Note that this speed  
controller is available only on selected  
models.  
5. Mounting heights and distance of  
throw recommendations as given  
elsewhere in this catalog should be  
carefully observed.  
6. In the case of Model P Units, they  
should be spotted so that they will most  
effectively prevent stratification of  
excessively warm air at the ceiling. By  
carefully observing this rule, this type of  
unit may be used between seasons to  
tap waste heat at the ceiling and drive it  
down to occupied zones, thereby  
eliminating the need for added heat on  
the system.  
Figure AC-1 –The floor plan and elevation of a typical industrial building showing how a  
Trane Unit Heater System will heat various parts.Where ceilings are high in the main  
manufacturing section, large Projection Heaters without diffusers are used.Where ceilings  
are exceptionally high, as in crane bays, Model P Units with Louver Cone Diffusers provide  
up to 45% greater throw to top the “ceiling heat reservoir.” Model P Units with half closed  
Louver Cones blanket doorways. Model S Units with Louver Fins blanket windows.  
extremely small height of the Model S,  
and because all piping connections are  
made at the back of the unit, the Model S  
provides a greater saving in headroom  
than other horizontal unit heater makes.  
As illustrated in Figure AC-1, the Model S  
Unit Heaters may be mounted  
In plants where the ceilings are  
exceptionally high, such as in crane bays  
as illustrated in Figure AC-1, Model P  
Units with Louver Cone Diffusers can  
increase the downward projection of  
heat by as much as 45% over units  
without diffusers.  
conveniently from the ceiling, or from  
building structural supports and beams.  
With Louver Fin Diffusers, they are ideal  
for blanketing windows, and Model S  
Bypass” Unit Heaters, provide further  
flexibility of application where greater  
throw and more effective distribution of  
air in the living zone is required.  
Model P Units with the Louver Cone  
Diffusers can also be used to blanket  
doorways effectively, as shown in Figure  
AC-1 by simply adjusting half of the  
louvers vertically, and half closed.  
Model S horizontal-type units are ideal  
for mounting in plant areas where  
ceilings are low. In fact, due to the  
7. Do not spot units close to any  
obstruction that will impede the full and  
natural air delivery of the unit.  
Typical Factory  
In the typical industrial building, where  
ceilings are high, Model P Unit Heaters  
may be used without diffusers.  
8
UH-PRC001-EN  
Application  
Considerations  
General Notes  
Hot Water System – Using Circulating  
Pump  
The following general notes on piping  
propeller unit heaters are presented  
based on competent engineering and  
installation practice:  
1. Suspend unit heaters securely with  
provisions for easy removal.  
Overhead supply and return mains are  
used with bottom connections to mains.  
Manual vent (pet cock) is used at high  
point on return main. Automatic air vent  
may be substituted if desired. Refer to  
Figure AC-2.  
2. Make certain units hang level vertically  
and horizontally.  
3. Provide for expansion in supply lines  
(note swing joints in suggested piping  
arrangements).  
4. Provide unions adjacent to unit heaters  
in both supply and return laterals. Also  
provide shut-off valves in all supply  
laterals.  
5. Use 45' angle runoffs from all supply  
and return mains.  
6. Provide at least 7" (more if necessary)  
clearance above tops of Model P  
Projection Unit Heaters. Motors are  
removable from below on all sizes.  
It is desirable to form dirt pockets with  
pipe of the same size as the return  
tapping of the unit heater. Pipe in the  
branch-off should be the same size as the  
tapping in the trap. Beyond the trap, the  
return lateral should be increased one  
size to the return main.  
Figure AC-3  
High Pressure Steam System  
Overhead supply main is used with  
lower return main. Where steam  
pressure fluctuates over a wide range, a  
swing check valve should be placed in  
the return lateral between strainer and  
bucket trap to prevent reverse flow of  
condensate of flash steam when  
pressure drops suddenly.Top of bucket  
trap must be located below return outlet  
of coil for complete drainage of  
condensate. Refer to Figure AC-3.  
Figure AC-2  
UH-PRC001-EN  
9
Application  
Considerations  
Table AC-1 - Model P Coil Face Area  
Unit Numbers  
42-P & P-L  
Fin Area In Sq. Ft  
1.20  
64-P & P-L  
1.49  
80-P & P-L  
1.98  
102-P & P-L  
122-P & P-L  
146-P & P-L  
166-P & P-L  
202-P & P-L  
252-P & P-L  
280-P & P-L  
336-P & P-L  
384-P & P-L  
500-P & P-L  
600-P & P-L  
720-P & P-L  
3.28  
3.28  
3.88  
4.85  
4.85  
6.52  
6.52  
6.52  
7.82  
8.72  
11.63  
13.08  
Figure AC-4  
Table AC-2 - Supply and Return Sizes at 2 Psi  
Capacity In Lbs. Of  
Size Of  
Supply  
1”  
1 1/4”  
1 1/2”  
2”  
Size Of  
Steam Per Hour  
Gravity Return  
39  
87  
134  
272  
449  
822  
3/4”  
3/4”  
1”  
1 1/4”  
1 1/2”  
2”  
2 1/2”  
3”  
Note: This table is based on 1/2 lb. drop per 100 ft. of  
equivalent run of steam line and approximately 1/4 lb. drop  
in the return line per 100 ft. increase steam run-outs one  
size if more than 8 ft. long.  
Figure AC-5  
Vapor orVacuum System  
Lower supply and return mains are used.  
Piping should be similar to that used with  
overhead supply main if it is separately  
vented and trapped. Bottom supply for  
steam mains may be used if steam is dry.  
Refer to Figure AC-4. For proper pipe size,  
refer toTable AC-2.  
Hot Water System with Circulating  
Pump  
Lower supply and return mains are  
shown. Overhead supply and return  
main connections, similar to those in  
Figure AC-2 may be used.The automatic  
air vent is shown here but a manual vent  
(pet cock) may be substituted. Refer to  
Figure AC-5.  
Figure AC-6  
High Pressure Steam System  
Overhead supply and return mains are  
used.The top of the bucket trap must be  
located below bottom return outlet of coil  
for complete drainage of condensate.  
Refer to Figure AC-6.  
10  
UH-PRC001-EN  
Selection  
Procedure  
Trane Propeller Unit Heaters  
Spacing of Units  
oversized heaters to extend the  
Both Model S and Model P Propeller  
Unit Heaters are ideally suited to such a  
wide variety of installations that there  
can be no hard and fast rules regulating  
their selection.  
In determining the type and size of the  
units for any building, the following  
points are generally considered:  
It is the usual practice to divide the  
building into areas with like exposures,  
or in relation to heat load distribution  
desired.  
In general, Model S Unit Heaters may  
be selected for buildings where direct  
horizontal air currents are desired and  
where there are no obstacles to  
interrupt the flow of air from the  
heaters.  
Model P Unit Heaters are successfully  
used where high or low mounting  
heights are required and should  
ordinarily be specified with diffusers,  
depending upon the mounting height  
and application.  
maximum effective mounting height of  
the Model P or the distance of throw of  
the Model S. Conversely,Trane Diffusers  
enable extremely low mounting since the  
adjustable blades direct heat where it is  
wanted without creating uncomfortable  
hot spots near the units.  
Second: After the original selection has  
been made, units may be located with  
confidence because adjustments in heat  
distribution are possible to  
accommodate future changes or  
unforeseen draft conditions.  
BTU Requirements  
While the choice of units depends upon  
several important factors, the total Btu  
requirement is usually determined first.  
In calculating heat loss, methods as  
recommended by the ASHRAE Guide  
may be used, or any other procedure  
which is known to be acceptable.  
Air Changes  
Better diffusion and more even  
temperatures can be maintained in a  
heated space when the rate of air  
recirculation through the heaters is  
relatively high. For buildings where large  
numbers of people are engaged, it is  
desirable to provide for a greater number  
of air changes than for sparsely occupied  
areas.  
A greater number of small units are used  
where wide diffusion and even  
temperatures are necessary. A few  
centrally located units of large capacity  
would be used where there are few  
occupants.  
Mounting Heights  
Type of Building  
The maximum effective mounting  
height is determined by the outlet  
temperature of the air, the outlet  
velocity, the cfm for which the heater is  
designed, and if a diffuser is used the  
setting of its blades.  
The higher the outlet temperature of  
the air, the more difficult it is to force it  
down into the living zone.  
The cfm also affects the mounting  
height as a large volume of air will  
travel farther than a small volume  
under the same initial conditions of  
temperature and velocity.  
In the preliminary planning stages, it is  
well to remember that the lowest  
possible mounting height is desirable in  
order to get the most heat down to the  
floor line and to allow the greatest  
possible diffusion adjustment to  
provide tailor-made distribution for  
each area.  
Once the total Btu requirement is known,  
the type of building together with its  
architecture and its purpose is  
considered.  
In the many cases where a combination  
of space characteristics is found, a  
combination of Model S and Model P  
Unit Heaters may be used to create the  
most satisfactory heating system.  
The Model P Unit Heater has the natural  
ability to tap the reservoir of heated air  
which collects at the ceiling level and  
return it to active service in the floor  
zone.  
The Model P can be used on either high  
or low ceilings. From high mounting  
positions the Model P will allow ample  
clearance for moving objects and can  
project heat down into occupied areas  
regardless of obstacles which would  
restrict the flow of air from horizontal  
units.  
From low mounting positions the Model  
P, with proper diffusion, can be used  
without disturbing nearby occupants  
with direct blasts of high velocity heated  
air, or requiring return lines so low as to  
leave insufficient head room.  
The superior horizontal action of the  
Model S, on the other hand, is ideal for  
creating a wiping effect of warm air  
along exposed walls which neutralizes  
drafts at their source, beaming heat  
down narrow aisles and production  
lines, and blanketing large windows,  
doors and other points of high heat loss.  
Comfort Conditions and Economy  
Air circulation, diffusion and spacing of  
units are closely related to economy and  
comfort in the selection of unit heaters.  
The more units used to provide the  
required number of Btus, the more  
comfortable will be the conditions for  
personnel. On the other hand, a few  
large units can be selected to provide  
plenty of heat at low first cost, but may  
be slower in response and thorough  
distribution of heat.  
In providing for the use of diffusers  
please remember, adjustment of a  
Louver Cone Diffuser to deflect the air  
toward the horizontal immediately  
lowers the mounting height limit.  
Adjustment for lateral deflection with  
the Louver Fin Diffuser shortens the  
distance of throw.  
Here again, adjustable diffusion  
equipment can go a long way toward  
saving the buyer first cost expense while  
still providing completely satisfactory  
comfort conditions.  
Diffusion  
The use of Trane Louver Cone or  
Louver Fin Diffusers influences the  
selection of units in two principal ways:  
First: It is seldom necessary to install  
UH-PRC001-EN  
11  
Selection  
Procedure  
Formula  
Example 1  
Determining FinalTemperature  
Final temperature of air leavingTrane  
Unit Heaters may be determined as  
follows:  
The following formula is used to arrive at  
final air temperature volume when 70 F  
(Standard Air Basis) is known or vice  
versa:  
Given: Model 60S Horizontal Propeller  
Unit Heater with a rated capacity of  
60,500 Btu at 2 lbs. steam with 60 F  
entering air.  
Inlet AirTemp. +  
Btu rating  
= FinalTemp  
Cfm at 70F x 1.085  
Cfm at final temp. =  
460 + Final temp.  
Desired: Capacity of this unit using  
15 lbs. steam and 40 F entering air.  
Cfm at 70 F x  
Inlet AirTemp. 40F +  
81,070 = FinalTemp  
460 + 70  
815(from table 3) x 1.085  
Cfm at 70 F =  
Example 2:  
460 + 70  
460 + Final temp.  
Under 40 F and across from 15 lbs. in  
SP-2, page 14, we find the factor 1.34.  
60,500 x 1.34 = 81,070 Btu per hour.  
Cfm final air x  
Problem: ATrane Model S Horizontal  
Unit Heater is desired to deliver 280,000  
Btu per hour in a garage where  
ventilation is required. Entering air  
temperature is 40 F. Steam at 30 lbs.  
pressure is available.Temperature to be  
maintained is 70 F.  
Determining Special Steam Capacities  
Where capacity of the unit under  
standard conditions is known 2 lbs.  
steam, 60 F entering air and it is  
desired to know the capacity of this  
same unit under different steam and air  
conditions, follow instructions given in  
Example 1 below.  
Equivalent Direct Radiation  
If working in EDR, rather than Btu,  
multiply the EDR by the same factor in  
the same way.Thus:  
252 (From Table 3) x 1.34 =  
Solution: Under 40 F and across from 30  
lbs. inTable SP-2 page 14, find the factor  
1.51.  
81,070  
240  
338 sq. ft. or  
Determining Amount of Condensate  
To determine the amount of condensate,  
divide the capacity in BTU by the latent  
heat of steam:  
Where a set of conditions is given Btu,  
temperature rise, final temperature, cfm,  
steam pressure available, etc. Refer to  
Example 2.  
Equivalent capacity of required unit at  
2 lbs. steam 60 F entering air is  
81,070  
945  
Useful Data  
= 86 lbs per hour.  
Required Btu per hour = 280,00 =185,400  
F
1.51 Btu  
Btu  
= Sq. ft. of radiation (EDR)  
240  
945 = Latent Heat of Steam at 15 psi.  
(SeeTable SP-9, page 18.)  
From Table SP-3, page 15, select a  
Number 186S Unit Heater with a  
capacity of 185,200 Btu per hour with  
standard coil, and at 2 lbs. steam and 60  
F entering air.  
Sq. ft. of radiation =Lbs. of condensate  
4
per hour  
Btu  
Latent heat  
= Lbs. of water per hour  
Cfm xTemp. rise x 1.085 = Btu.  
Specific heat of air (70 F) = .241  
The capacity of this unit at 30 lbs. steam  
and 40 F entering air is  
1.51 x 185,200 = 279,650 Btu per hour.  
Surplus Capacity  
Specific weight of one cubic foot of air  
(70 F) =.075.  
While the ventilation load is being  
handled, any air entering the space over  
the desired room temperature should be  
considered in the heating calculations.  
This surplus capacity can be found by  
multiplying the difference between the  
final temperature leaving the heater and  
the room temperature to be maintained  
by 1.085 and that by the cfm.That  
amount of heat can be used to offset  
heat losses.  
Cfm x 60 = cfh.  
Therefore, .241 x .075 x 60 = 1.085  
12  
UH-PRC001-EN  
Selection  
Procedure  
Model S Nomenclature  
UHS  
A
0 1 8  
S
2
E
A
A
1
T
A
W
D
A
D
B
E
123  
4
5 6 7  
8
9
10 11 12 13 14 15 16 17 18 19 20 21  
Digits 1,2,3 – Product Type  
Digit 4 – Development Sequence  
Digits 5,6,7 – Unit Size  
Table SP-1 – Max. Mounting Heights and Distance ofThrow for Model S Units  
(Based on 2 Lbs. Steam Pressure 60 F Entering Air)  
Maximum Throw  
Final  
Temp.  
(F)  
With Louver Fin  
Outlet  
Velocity  
162  
186  
319  
347  
343  
454  
382  
476  
411  
452  
528  
431  
529  
442  
550  
583  
220  
359  
363  
439  
407  
458  
394  
448  
495  
430  
514  
439  
536  
Mounting Without  
Set for  
Unit  
18-S  
CFM  
280  
Height  
8
Diffuser  
12  
15  
18  
20  
22  
28  
28  
28  
32  
40  
45  
40  
50  
50  
60  
65  
18  
20  
25  
28  
30  
32  
32  
40  
45  
42  
48  
55  
60  
Maximum Throw  
117  
118  
126  
125  
129  
117  
127  
118  
126  
127  
121  
124  
118  
127  
118  
122  
106  
104  
107  
105  
108  
107  
108  
108  
107  
109  
107  
108  
105  
15  
18  
22  
25  
27  
35  
35  
35  
40  
50  
56  
50  
62  
62  
75  
80  
22  
25  
31  
35  
37  
40  
40  
50  
56  
52  
60  
68  
75  
20-S2  
38-S  
318  
8
544  
9
Digit 8 – CoilType  
42-S  
590  
9
9
60-S  
815  
S = Hot Water or Steam  
W = Hot Water withTurbulators  
70-S  
1100  
1214  
1535  
1760  
2380  
2808  
3300  
4100  
4480  
5660  
6017  
390  
10  
11  
12  
13  
14  
14  
15  
15  
15  
15  
15  
8
90-S  
100-S  
126-S  
168-6  
186-S  
230-S  
260-S  
320-S  
354-S  
400-S  
19-S2  
31-S  
Digit 9 – Fin Series  
2 = 132  
8 = 108  
Digit 10 – Design Sequence  
Digit 11 Tube Material  
Digit 12 – Fin Material  
635  
897  
8
9
45-S  
53-S  
1090  
1337  
1510  
1740  
2440  
2700  
3392  
4059  
4607  
5644  
10  
12  
13  
14  
15  
15  
15  
15  
15  
15  
69-S  
77-S  
91-S  
127-S  
137-S  
181-S  
207-S  
243-S  
273-S  
Digit 13 —Voltage  
Digit 14 — MotorType  
Digit 15 — Motor Mount/Fan Guard  
Digit 16 — Special Coatings  
Digit 17 — Diffuser  
Digit 18 — Manual Starter  
Digit 19 — Speed Controller (115/60/1  
standard motors)  
Digit 20 —Thermostats  
Digit 21 — Subbase  
Digit 22 —Voltage  
UH-PRC001-EN  
13  
Selection  
Procedure  
Model S  
Model P  
Maximum mounting heights for Model  
S Unit Heaters are given inTable SP-1.  
When equipped with standard Louver  
Fin Diffusers the distance of throw may  
be increased as much as 25% by toeing-  
inthe vertical blades. Distance of throw  
decreases in proportion to the amount of  
deflection given the airstream to either  
side of the heater.  
Maximum mounting heights for Model P  
Unit Heaters are given in Table SP-10,  
page 19.These distances are figured  
from the floor line to the bottom plate of  
the unit heater.  
Where ceilings are unusually low, a  
nearly horizontal flow of air can be  
obtained by equipping these units with  
Louver Cone Diffusers.The individually  
adjustable blades of the Louver Cone  
permit an infinite variety of adjustments  
to meet any on-the-job problems. By  
setting the blades vertically to straighten  
the airstream, as much as 45% increase  
in throw can be obtained.  
Mounting the unit at or below maximum  
mounting height will insure that heated  
air reaches the living zone.  
Table SP-2 – Factors for Determining Steam Capacity of Model S Horizontal Unit Heaters at Various Pressures and Temperatures  
Table Based on 2 PSIG and 60 F Entering Air  
Steam  
Temperature of Entering Air (F)  
Pressure PSIG  
-10  
0
10  
20  
30  
40  
50  
60  
70  
80  
90  
100  
0
2
5
1.54  
1.59  
1.64  
1.73  
1.80  
1.86  
1.97  
2.06  
2.13  
2.20  
2.26  
2.28  
1.45  
1.50  
1.55  
1.64  
1.71  
1.77  
1.87  
1.96  
2.04  
2.09  
2.16  
2.18  
1.37  
1.41  
1.46  
1.55  
1.61  
1.68  
1.78  
1.86  
1.94  
2.00  
2.06  
2.09  
1.27  
1.32  
1.37  
1.46  
1.53  
1.58  
1.68  
1.77  
1.85  
1.90  
1.96  
1 .99  
1.19  
1.24  
1.29  
1.38  
1.44  
1.50  
1.60  
1.68  
1.76  
1.81  
1.87  
1.90  
1.11  
1.16  
1.21  
1.29  
1.34  
1.42  
1.51  
1.60  
1.67  
1.73  
1.78  
1.81  
1.03  
1.08  
1.13  
1.21  
1.28  
1.33  
1.43  
1.51  
1.58  
1.64  
1.70  
1.72  
0.96  
1.00  
1.05  
1.13  
1.19  
1.25  
1.35  
1.43  
1.50  
1.56  
1.61  
1.64  
0.88  
0.93  
0.97  
1.06  
1.12  
1.17  
1.27  
1.35  
1.42  
1.47  
1.53  
1.55  
0.81  
0.85  
0.90  
0.98  
1.04  
1.10  
1.19  
1.27  
1.34  
1.39  
1.45  
1.47  
0.74  
0.78  
0.83  
0.91  
0.97  
1.02  
1.12  
1.19  
1.26  
1.31  
1.37  
1.40  
0.67  
0.71  
0.76  
0.84  
0.90  
0.95  
1.04  
1.12  
1.19  
1.24  
1.29  
1.32  
Blow-  
Through  
Type  
10  
15  
20  
30  
40  
50  
60  
70  
75  
Notes:  
To determine the Btu per hour capacity of a Model S Horizontal Unit Heater at any steam pressure and entering air temperature multiply rated capacity at 2 psig steam 60 F entering air (Table  
SP-3) by factor from above table. Factors in italics: Units should not be operated when entering air is below freezing at steam pressures below 10 psig.  
14  
UH-PRC001-EN  
Selection  
Procedure  
Table SP-3 – Model S Horizontal Unit Heater Steam Capacities  
2 Lbs. Steam 60 F Entering AirTemp  
Motor  
HP  
Motor  
RPM  
BTU  
Condensate  
Lbs Per Hr  
Final  
CFM 70 F  
Air Basis  
Outlet  
Oper.  
Size  
18-S  
Per Hour  
EDR  
Temp  
Velocity  
Weight  
Standard Units  
1050  
950  
17,400  
16,600  
13,900  
20,000  
19,000  
15,500  
38,700  
35,900  
32,700  
41,600  
38,000  
34,700  
60,500  
56,000  
51,200  
68,200  
64,900  
59,700  
87,600  
81,200  
74,200  
96,000  
91,500  
84,000  
72  
69  
18  
17  
14  
21  
20  
17  
40  
37  
33  
43  
39  
35  
64  
58  
52  
70  
67  
61  
90  
84  
76  
99  
94  
86  
117  
118  
118  
118  
120  
120  
126  
130  
135  
125  
130  
136  
129  
133  
139  
117  
123  
128  
127  
131  
137  
118  
123  
128  
280  
266  
224  
318  
162  
154  
130  
186  
173  
145  
319  
279  
238  
347  
294  
251  
343  
300  
256  
454  
397  
339  
382  
334  
285  
476  
417  
356  
1/50  
1/50  
1/20  
1/20  
1/20  
1/8  
40  
40  
40  
40  
55  
60  
75  
85  
800  
58  
1050  
950  
84  
20-S2  
38-S  
79  
298  
250  
544  
472  
399  
590  
495  
420  
815  
800  
64  
1550  
1300  
1100  
1550  
1300  
1100  
1550  
1300  
1100  
1550  
1300  
1100  
1550  
1300  
1100  
1550  
1300  
1100  
162  
150  
136  
174  
158  
145  
252  
234  
214  
285  
271  
248  
366  
340  
310  
400  
380  
350  
42-S  
60-S  
706  
597  
1100  
953  
806  
1214  
1053  
891  
1535  
1330  
1126  
70-S  
90-S  
1/8  
100-S  
1/8  
126-S  
168-8  
1/6  
1/6  
1100  
1100  
125,700  
172,000  
525  
716  
130  
178  
126  
127  
1760  
2380  
411  
452  
100  
145  
186-S  
230-S  
260-S  
320-S  
354-8  
400-S  
1/4  
1/4  
1/2  
1/2  
1/2  
3/4  
1100  
1100  
1100  
1100  
1100  
1145  
185,200  
229,700  
256,300  
324,000  
355,500  
404,073  
775  
957  
1070  
1350  
1480  
1684  
191  
237  
265  
335  
368  
418  
121  
124  
118  
127  
118  
122  
2808  
3300  
4100  
4480  
5660  
6017  
528  
431  
529  
442  
550  
583  
145  
190  
195  
245  
250  
260  
Notes:  
1. Constant speed units are rated at capacities shown in regular type: Capacities in italic faced type apply only to  
units with multi-speed motors.  
2. Capacities based on 2 psi steam and 60 F entering air.  
UH-PRC001-EN  
15  
Selection  
Procedure  
Table SP-4 – Model S Horizontal Unit Heater Steam Capacities cont  
2 Lbs. Steam 60 F Entering AirTemp  
Motor  
HP  
Motor  
RPM  
BTU  
Per Hour  
Condensate  
Lbs Per Hr  
Final  
Temp  
CFM 70 F  
Air Basis  
Outlet  
Velocity  
Oper.  
Weight  
Size  
EDR  
Low FinalTemp. BypassUnits  
1050  
950  
19,300  
18,300  
16,300  
30,400  
27,800  
25,300  
45,800  
41,300  
37,300  
53,300  
50,200  
46,200  
69,400  
63,400  
57,600  
76,600  
71,700  
65,800  
80  
20  
19  
17  
31  
29  
26  
47  
43  
39  
55  
52  
48  
72  
66  
60  
79  
74  
68  
106  
108  
110  
104  
109  
112  
107  
112  
116  
105  
109  
114  
108  
112  
116  
107  
111  
390  
360  
220  
205  
173  
359  
302  
257  
363  
304  
259  
439  
383  
327  
407  
346  
295  
458  
300  
341  
19-S2  
1/25  
1/20  
1/20  
1/8  
77  
68  
40  
40  
55  
55  
70  
80  
800  
300  
635  
1550  
1300  
1100  
1550  
1300  
1100  
1550  
1300  
1100  
1550  
1300  
1100  
1550  
1300  
1100  
127  
116  
106  
191  
173  
156  
223  
209  
192  
290  
264  
240  
320  
299  
274  
31-S  
45-S  
53-S  
69-S  
77-S  
520  
450  
897  
740  
630  
1090  
940  
795  
1337  
1125  
955  
1/8  
1510  
1304  
1100  
1/8  
116  
91-S  
127-S  
1/6  
1/6  
1100  
1100  
91,000  
125,800  
380  
524  
94  
130  
108  
108  
1740  
2440  
394  
448  
95  
135  
137-S  
181-S  
207-S  
243-S  
273-S  
1/4  
1/4  
1/2  
1/2  
1/2  
1100  
1100  
1100  
1100  
1100  
135,800  
180,700  
206,900  
238,700  
272,200  
567  
755  
863  
995  
1135  
140  
187  
214  
248  
283  
107  
109  
107  
108  
105  
2700  
3392  
4059  
4607  
5644  
495  
430  
514  
439  
536  
135  
180  
185  
230  
235  
Notes:  
1. Constant speed units are rated at capacities shown in regular type: Capacities in italic faced type apply only to units with multi-speed motors.  
2. Capacities based on 2 psi steam and 60 F entering air.  
16  
UH-PRC001-EN  
Selection  
Procedure  
Table SP-5 – Model P Projection Unit Heater Steam Capacities  
2 Lbs. Steam 60 F Entering AirTemperature  
Motor  
HP  
Motor  
RPM  
BTU  
Condensate  
Lbs Per Hr  
Final  
CFM 70 F  
Air Basis  
CFM at  
FinalTemp.  
Outlet  
Velocity  
Oper.  
Weight Lbs.  
Size  
Per Hour  
EDR  
Temp.  
Standard Models  
42-P  
64-P  
80-P  
102-P  
122-P  
1/25  
1/20  
1/20  
1/8  
1550  
41,300  
172  
43  
124  
595  
660  
877  
30  
35  
40  
55  
55  
1150  
1550  
33,600  
65,500  
140  
273  
35  
68  
131  
121  
436  
989  
495  
1085  
658  
1005  
1150  
1550  
52,800  
80,600  
220  
336  
55  
83  
129  
122  
706  
1200  
785  
1320  
727  
1220  
1150  
1070  
65,100  
101,800  
271  
424  
67  
106  
130  
123  
858  
1490  
954  
1635  
894  
980  
850  
1070  
87,900  
124,400  
366  
518  
91  
129  
129  
124  
1180  
1790  
1315  
1970  
783  
1170  
1/6  
146-P  
166-P  
202-P  
252-P  
280-P  
336-P  
384-P  
500-P  
600-P  
720-P  
1/6  
1/6  
1070  
1070  
1070  
1070  
1070  
1120  
1120  
1120  
1120  
1120  
152,000  
173,000  
210,200  
249,800  
283,800  
333,400  
386,000  
496,000  
585,000  
705,000  
633  
720  
157  
179  
208  
260  
294  
345  
400  
514  
605  
729  
123  
121  
118  
115  
119  
119  
118  
117  
117  
119  
2220  
2620  
3200  
4180  
4430  
5210  
6140  
8020  
9450  
11,000  
2440  
2870  
1045  
1230  
1495  
1205  
1275  
1500  
1770  
1640  
1930  
2250  
80  
80  
1/4  
838  
3490  
85  
1/4  
1040  
1180  
1390  
1610  
2070  
2440  
2940  
4550  
135  
135  
135  
175  
250  
260  
325  
1/2  
4840  
3/4  
5690  
3/4  
6700  
8750  
1-1/2  
1-1/2  
3
10,300  
12,020  
Low FinalTemperature Models - Standard Model P Units With All Air Ports Open  
42-P-L  
64-P-L  
80-P-L  
102-P-L  
122-P-L  
1/25  
1/20  
1/20  
1/8  
1150  
34,800  
145  
36  
108  
668  
716  
950  
30  
35  
40  
55  
55  
1150  
1550  
26,000  
57,200  
108  
238  
27  
59  
111  
104  
470  
1200  
506  
1280  
672  
1190  
1150  
1550  
45,800  
68,000  
191  
283  
48  
71  
109  
106  
862  
1360  
925  
1455  
858  
1350  
1150  
1070  
55,000  
85,400  
229  
356  
57  
89  
111  
108  
995  
1640  
1070  
1760  
992  
1050  
850  
1070  
71,200  
111,000  
296  
462  
74  
115  
111  
107  
1290  
2180  
1390  
2330  
827  
1390  
1/6  
146-P-L  
166-P-L  
202-P-L  
252-P-L  
280-P-L  
336-P-L  
384-P-L  
500-P-L 1-1/2  
600-P-L 1-1/2  
720-P-L  
1/6  
1/6  
1/4  
1/4  
1/2  
3/4  
3/4  
1070  
1070  
1070  
1070  
1070  
1120  
1120  
1120  
1120  
1120  
125,800  
149,000  
176,800  
214,900  
251,800  
291,000  
344,000  
428,000  
515,000  
620,000  
524  
620  
130  
154  
183  
224  
260  
302  
356  
446  
533  
642  
109  
107  
108  
104  
106  
107  
108  
102  
106  
108  
2360  
2920  
2530  
3130  
1080  
1340  
1560  
1270  
1420  
1610  
1870  
1860  
2060  
2380  
80  
80  
736  
3390  
3640  
85  
895  
4500  
5040  
5700  
6600  
9380  
10,300  
11,900  
4800  
5380  
135  
135  
135  
175  
250  
260  
325  
1050  
1210  
1430  
1785  
2140  
2580  
6100  
7080  
9940  
11,000  
12,750  
3
Notes:  
Constant speed units are rated at capacities shown in regular type; capacities in italic faced type apply only to units with multi-speed motors.  
To determine BTU per hour capacities at various steam pressures and entering air temperatures, use conversion factors from Table SP-7, page 18.  
Final temperatures at new conditions can be calculated by applying basic formula.  
Table SP-6 – Maximum Spread (Ft.)  
Unit No.  
Spread (Ft.)  
Note:  
42P  
15  
64P  
17  
80P  
20  
102P  
24  
122P  
26  
146P  
27  
166P  
28  
202P  
32  
252P  
35  
280P  
37  
336P  
45  
384P  
50  
500P  
54  
600P  
57  
720P  
60  
The “spread” is the diameter of the comfort zone at floor level, projected by the Model P unit without the louver cone diffuser, based on two pounds steam pressure and 60 F entering air.  
UH-PRC001-EN  
17  
Selection  
Procedure  
Model P Nomenclature  
Digit 15 – Fan Guard  
Digit 16 – Unit Coating  
Digit 17 – Diffuser  
UHP  
A
0 4 2  
P
4
C
A
A
1
T
A
R
C
A
D
B
E
123  
4
5 6 7  
8
9
10 11 12 13 14 15 16 17 18 19 20 21  
Digits 1,2,3 – Product Type  
Digit 10 – Design Sequence  
Digit 4 – Development Sequence  
Digits 5,6,7 – Unit Size  
Digit 8 – CoilType  
Digit 11 Tube Material  
Digit 12 – Fin Material  
Digit 13 –Voltage  
Digit 18 – Manual Starter  
Digit 19 – Speed Controller (115/60/1  
standard motors)  
Digit 20 –Thermostats  
Digit 21 – Subbase  
Digit 9 – Fin Series  
Digit 14 – MotorType  
Table SP-7 – Factors For Determining Steam Capacity Of Model P Projection Unit Heaters At Various Pressures And Temperatures  
Table Based on 2 PSIG and 60 F Entering Air  
Steam  
Temperature of Entering Air (F)  
Pressure PSIG  
-10  
0
10  
20  
30  
40  
50  
60  
70  
80  
90  
100  
0
2
1.49  
1.52  
1.58  
1.64  
1.70  
1.75  
1.83  
1.90  
1.96  
2.02  
2.07  
2.10  
1.41  
1.45  
1. 50  
1.57  
1.62  
1.67  
1.75  
1.82  
1.87  
1.94  
1.99  
2.02  
1.33  
1.37  
1.42  
1.49  
1.55  
1.60  
1.68  
1.75  
1.81  
1.87  
1.92  
1.94  
1.25  
1.29  
1.34  
1.41  
1.47  
1.52  
1.61  
1.68  
1.74  
1.79  
1.84  
1.86  
1.18  
1.22  
1.27  
1.34  
1.40  
1.45  
1.53  
1.61  
1.67  
1.72  
1.76  
1.79  
1.11  
1.15  
1.20  
1.27  
1.32  
1.37  
1.46  
1.53  
1.59  
1.64  
1.69  
1.71  
1.03  
1.07  
1.12  
1.19  
1.25  
1.30  
1.39  
1.46  
1.52  
1.57  
1.62  
1.64  
0.96  
1.00  
1.05  
1.12  
1.18  
1.23  
1.32  
1.39  
1.45  
1.50  
1.55  
1.57  
0.90  
0.93  
0.98  
1.05  
1.11  
1.16  
1.25  
1.32  
1.38  
1.43  
1.47  
1.49  
0.83  
0.86  
0.91  
0.98  
1.04  
1.09  
1.18  
1.25  
1.31  
1.36  
1.40  
1.42  
0.76  
0.80  
0.85  
0.91  
0.97  
1.02  
1.11  
1.18  
1.24  
1.29  
1.33  
1.36  
0.69  
0.73  
0.78  
0.85  
0.90  
0.96  
1.04  
1.11  
1.17  
1.22  
1.27  
1.29  
5
10  
Draw-  
Through  
Unit  
15  
20  
30  
40  
50  
60  
70  
75  
Note:  
To determine the Btu per hour capacity of a Model P projection unit heater at any steam pressure and entering air temperature, multiply rated capacity at 2 psig steam 60 F entering air (Table  
SP-5) by factor from above table.  
Table SP-8 – Factors for Determining Unit  
Heater Capacities at 25 or 50 Cycles  
Additional Selection Data  
MultiplierTo Be AppliedTo  
RPM  
25 CY  
60-Cycle 1100 RPM Ratings  
Motor and Fan Speeds  
25 and 50 Cycle Unit Heat Capacities  
Table SP-8 shows the Btu, cfm, and the  
hp required on unit heaters when  
operated on 25 or 50 cycle circuits.  
The multipliers inTable SP-8 may be  
applied to standard 60 cycle unit  
capacities to determine the capacities of  
the same unit when operating on  
25 or 50 cycle current.These multipliers  
may be used on units cataloged at  
1050 to 1150 RPM.  
50 CY  
1425  
950  
BTU  
1.17  
.87  
CFM  
1.25  
.833  
.623  
HP  
Motor and fan speeds are selected to  
provide efficient performance.The  
solid-state speed control will provide an  
infinite number of speeds between the  
highest and the lowest cataloged fan  
speeds.The speed control is not  
calibrated in specific fan speeds. For use  
on units with 115 volt/60 cycle/  
1 phase, 1/8 hp and smaller standard  
motors only.  
1425  
1.95  
.572  
.242  
710  
710  
.7  
Table SP-9 – Properties of Steam  
Gauge Pressure  
Temp.  
F
Latent  
Heat  
965  
960  
952  
945  
939  
933  
928  
919  
Lbs.  
2
5
219  
227  
239  
250  
259  
267  
274  
287  
298  
307  
316  
320  
10  
15  
20  
25  
30  
40  
50  
60  
70  
75  
For the smallerTrane Unit Heaters  
cataloged at 1550 RPM, the capacity data  
in the catalog may be applied to either  
25 or 50 cycle service.  
Standard and Bypass Units  
Standard models meet most  
requirements and are most economical.  
Bypass units meet conditions as  
mentioned above, and are also used  
where low final temperature is specified.  
911  
904  
897  
891  
18  
UH-PRC001-EN  
Selection  
Procedure  
Table SP-10 - Maximum Mounting Heights in Feet for Model P Unit Heaters  
with and without Louver Cone Diffuser  
Hot Water Selection Example  
Selection Procedure  
Unit  
Size  
Steam Pressure (PSI)  
Unit  
Size  
Steam Pressure (PSI)  
10 50 75  
Select the proper size of unit heater for  
whatever application desired, as  
illustrated by the following examples.  
2
5
10  
50  
75  
2
5
42-P  
10.5 10.0 10.0  
9.0  
8.0  
146-P-L  
18.0 17.5  
17.5 15.0 14.0  
22.5 22.0 21.5 18.5 18.0  
18.0 17.5 17.0 14.5 14.0  
12.5 12.0 12.0 11.0 10.0  
42-P LS*  
42-P-L**  
42-P-L LS  
64-P  
8.0  
9.0  
8.0  
8.0  
8.0  
8.0  
8.0  
9.5  
166-P  
Example 1:  
8.5  
8.5 8.0  
22.5 22.0 21.5 19.0 18.0  
22.0 21.5 21.0 18.5 17.5  
27.5 27.0 26.5 23.5 22.5  
22.0 21.5 21.0 18.5 17.5  
27.5 27.0 26.5 24.0 23.0  
25.5 250 24.5 22.0 21.0  
31.5 31.0 30.5 27.0 26.0  
20.0 19.5 19.0 17.0 16.0  
25.0 24.0 23.5 20.5 19.5  
24.0 23.5 23.0 20.0 19.0  
29.5 28.5 28.0 24.5 23.5  
21.0 20.5 20.0 17.5 17.0  
26.0 25.5 25.0 22.0 21.0  
25.5 25.0 24.5 21.0 20.0  
32.0 31.0 30.0 26.0 25.0  
24.0 23.0 22.0 20.0 19.0  
30.0 29.0 28.0 25.0 24.0  
29.0 28.5 28.0 25.0 24.0  
36.0 35.0 34.0 30.0 29.0  
Select a Model S horizontal unit heater to  
deliver 95 MBH with 220°F entering  
water temperature (EWT), 70°F entering  
air temperature (EAT) and a 30°F water  
temperature drop (WTD).  
12.5 12.0 12.0 10.5  
166-P-L  
202-P  
14.5 14.0 13.5 12.0 11.5  
9.0  
10.5 10.0 10.0 9.0  
12.0 11.5 11.5 10.0  
8.5  
8.5  
8.0  
8.0  
8.5  
9.5  
202-P-L  
252-P  
14.5 14.0 14.0 12.0 11.5  
64-P LS  
64-P-L  
64-P-L LS  
80-P  
9. 5  
9.0  
9.0  
8.0  
8.0  
9.0  
11.5 11.0 11.0 9.5  
15.0 14.5 14.5 12.5 12.0  
252-P-L  
280-P  
Step 1.  
Determine GPM:  
GPM = Btu/hr = 95000 = 6.53  
(485)WTD 485 x 30  
19.0 18.5 18.5 16.5 16.0  
11.5 11.0  
11.0  
9.5  
8.0  
14.0 13.5 13.5 12.0 11.5  
15.0 14.5 14.0 12.0 4.5  
18.5 18.0 17.5 15.5 13.5  
11.0 10.5 10.5 9.0 8.5  
13.5 13.0 13.0 11.5 11.0  
18.0 17.5 17.5 15.0 14.0  
280-P-L  
336-P  
80-P LS  
80-P-L  
Step 2.  
336-P-L  
384-P  
22.0 21.0 21.0 19.0 18.0  
Refer toTable SP-11 to select the  
conversion factor at 220° EWT and 70°  
EAT. Factor is 1.058.  
80-P-L LS 13.0 12.5 12.0 11.0 10.5  
28.5 28.0  
27.5 24.0 23.0  
17.0 16.5 16.0 14.0 13.5  
35.5 35.0 34.0 30.0 29.0  
32.5 31.5 30.5 27.5 26.5  
41.0 40.0 39.0 35.0 33.5  
29.5 29.0 28.5 25.0 24.0  
36.5 36.0 35.5 32.0 30.5  
35.0 34.0 33.0 29.0 28.0  
43.5 42.5 41.5 35.0 34.0  
34.0 33.0 32.0 28.0 27.0  
42.5 41.5 40.5 36.0 34.5  
37.0 36.0 35.0 31.0 30.0  
46.5 45.5 44.5 39.0 37.0  
38.5 37.5 36.5 32.0 30.5  
48.0 47.0 46.0 40.0 39.0  
42.5 41.5 40.5 35.0 33.5  
53.0 52.0 51.0 44.0 42.0  
102-P  
14.0 13.5 13.0 11.5 11.0  
384-P-L  
500-P  
17.0 16.5 16.0 14.0 13.5  
102-P LS  
102-P-L  
11.0 10.5 10.5  
9.5  
9.0  
Step 3.  
13.5 13.0 13.0 12.0 11.5  
17.5 17.0 16.5 15.0 14.5  
21.5 21.0 20.5 18.5 17.5  
500-P-L  
600-P  
Determine equivalent MBH at standard  
conditions (200° EWT, 60° EAT).  
Equiv. MBH = MBH = 95 = 89.8  
Factor 1.058  
102-P-L LS 15.0 14.5 14.5 13.0 12.5  
18.5 18.0 18.0 16.0 15.0  
122-P  
16.0 15.5 15.5 14.0 13.5  
19.5 19.0 18.5 17.0 16.0  
21.0 20.5 20.0 17.5 17.0  
26.0 25.5 25.0 22.5 21.5  
15.5 15.0 14.5 13.0 12.0  
19.0 18.5 18.0 16.0 15.5  
600-P-L  
720-P  
Step 4.  
122-P-L  
146-P  
Select unit size by entering the hot water  
tables at the 200 °F EWT column. Select  
the unit which will provide 89.8 MBH at  
6.53 GPM. In this example, the selection  
indicates a Model S 126W2 unit heater,  
from Table PD-2, page 28.  
To determine the actual capacity of this  
Model S 126W2 at operating conditions  
(220° EWT and 70° EAT) proceed as  
follows.  
720-P-L  
Notes:  
*LS = Low speed.  
**PL = Model P low final temperature model with all air ports open.  
Figures in bold face show maximum mounting height with louver cone diffusers set vertically.  
To meet CSA and OSHA requirements, Model P Unit Heaters mounted lower than 8.0 ft. from the floor must be equipped with  
an OSHA fan guard. Above table based on 60 F entering air temperature. In providing for the use of diffusers, it must be  
remembered that adjustment of a LCD to deflect air toward horizontal immediately lowers the mounting height limit.  
Step 1.  
Determine the MBH at 6.53 GPM by  
interpolation in the 200° column. (In this  
case 90.8 MBH.) Multiply this MBH by the  
conversion factor 90.8 MBH x 1.058 = 96  
MBH.  
Step 2.  
The GPM remains constant = 6.53 GPM.  
Step 3.  
Calculate the water temperature drop  
WTD = Btu/hr  
=
96000 = 30.3  
GPM x 485 (6.53) (485)  
UH-PRC001-EN  
19  
Selection  
Procedure  
Step 4.  
Example 2  
Step 4.  
WTD = 27.5 x 0.546 = 15°  
Step 5.  
Determine the pressure drop at 6.53  
GPM. Pressure drops are cataloged for  
both standard wall (SWT) and heavy  
wall. (HWT) tube coils. In this example, if  
a SWT coil is selected the pressure drop,  
by interpolation is 2.38 feet of water.  
Determine the capacity of a Model 336P  
unit heater operating at 180° (EWT), 100°  
(EAT) and 15° (WTD).  
Btu/hr  
485xWTD (485)(15)  
123,000  
= 16.9  
GPM =  
=
Step 1.  
Find conversion factor (in Table SP-11)  
= 0.546  
Step 6.  
Pressure drop interpolated at 27.5°WTD  
Step 5.  
Step 2.  
for a SWT coil is 1.82 feet of water.  
Calculate the final air temperature  
Adjust the water temperature drop  
Step 7.  
Btu/hr  
CFM x 1.085  
15  
.546  
F.T. = E.A.T. +  
Adj. WTD =  
= 27.5°  
Calculate final temperature  
Btu/hr  
F.T. = E.A.T. +  
96000  
1661 x 1.085  
= 70 +  
=
70 + 53.2 = 123.2°  
Step 3.  
CFM x 1.085  
123,000  
= 121.8°  
Multiply the MBH (interpolated) at  
27.5°WTD, 200° EWT and 60° EAT by the  
factor to obtain the MBH at desired  
conditions.  
= 100°  
+
5210 x 1.085  
0.546 x 224.9 = 123.0 MBH  
Note:  
If a constant water temperature drop is desired, apply the conversion factor to the WTD and to the desired MBH and enter 200° EWT column at these conditions. Select the unit which will  
provide the equivalent MBH at the adjusted WTD. The GPM can then be interpolated from the table at the adjusted WTD. To determine the actual capacity at operating conditions proceed as  
outlined in example #2.  
If a constant GPM is desired, enter the 200° EWT column at the given or calculated GPM. Select the unit which will provide the equivalent MBH at this GPM. To determine the actual capacity  
at operating conditions in this case proceed as outlined in example #1.  
Table SP-11 – Unit Heater Hot Water Conversion Factors (Applies To Tables PD-1 - PD-5)  
Ent.  
Air  
Entering WaterTemperature  
Temp. 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390 400  
30 .962 1.036 1.110 1.182 1.259 1.331 1.408 1.482 1.554 1.627 1.702 1.780 1.850 1.925 2.000 2.070 2.142 2.220 2.295 2.370 2.440 2.515 2.590 2.660 2.735  
40 .880 .954 1.024 1.100 1.171 1.249 1.318 1.391 1.468 1.539 1.612 1.686 1.759 1.831 1.909 1.976 2.048 2.120 2.193 2.268 2.348 2.417 2.488 2.560 2.632  
50 .795 .869 .940 1.011 1.085 1.158 1.230 1.301 1.374 1.448 1.520 1.590 1.664 1.735 1.809 1.882 1.953 2.024 2.095 2.168 2.242 2.312 2.388 2.459 2.530  
60 .715 .785 .859 .929 1.000 1.071 1.141 1.215 1.285 1.359 1.429 1.500 1.571 1.642 1.715 1.785 1.858 1.930 2.000 2.070 2.140 2.215 2.285 2.360 2.430  
70 .634 .704 .774 .845 .917 .988 1.058 1.129 1.200 1.270 1.340 1.410 1.482 1.552 1.622 1.694 1.764 1.838 1.907 1.976 2.045 2.116 2.188 2.258 2.332  
80 .568 .628 .698 .768 .838 .908 .978 1.048 1.118 1.188 1.258 1.328 1.398 1.468 1.538 1.604 1.674 1.742 1.815 1.884 1.952 2.020 2.091 2.162 2.230  
90 .484 .552 .622 .690 .760 .829 .898 .967 1.036 1.106 1.173 1.244 1.311 1.380 1.450 1.515 1.585 1.655 1.723 1.795 1.862 1.930 1.998 2.067 2.137  
100 .410 .478 .546 .615 .684 .753 .820 .889 .957 1.025 1.095 1.161 1.230 1.300 1.368 1.433 1.499 1.569 1.638 1.705 1.776 1.843 1.910 1.977 2.046  
Apply to the 200 F entering water capacities only.  
Table SP-12 –Trane Unit Heater Nomenclature (Applies To Tables PD-1 - PD-5)  
Abbreviations  
MBH  
Definitions  
1000 BTU Per Hour  
GPM  
Gallons Per Minute  
FinalTemperature °F  
Feet OfWater Pressure Drop - Standard WallTubes.  
Feet OfWater Pressure Drop - Heavy WallTubes  
FT  
PD-S.W.T.  
PD-H.W.T  
Propylene  
Propylene  
Glycol  
Correction Factors for Propylene  
Glycol/Water  
When sizing equipment for systems that  
will utilize a propylene glycol solution,  
consider the following factors:  
2. GPM required @180F,  
20°D (no correction to  
pump curve)  
Glycol  
1.10%  
7. pH@50% by volume.  
8. Freezing Point  
9.5  
3. Pump head required  
@180F w/increase in  
GPM  
55% by volume —  
50%  
40%  
30%  
20%  
-28F  
-13F  
+28F  
+17F  
1. Heat transfer @180F with no increase  
1.23%*  
in flow rate  
Propylene  
Glycol  
4. Specific gravity  
(water = 1.0)  
1.045-1.055*  
**Com pared to water  
20% solution  
50% solution  
.97*  
.90*  
5. Pounds/Gallons@60F  
(water = 8.3453  
Pounds/Gallons)  
8.77  
20  
UH-PRC001-EN  
Model  
Num ber  
Description  
MODEL P UNIT HEATER  
UHP  
A
0 4 2  
P
4
C
A
A
1
T
A
R
C
A
D
B
E
123  
4
5 6 7  
8
9
10 11 12 13 14 15 16 17 18 19 20 21  
Digits 1,2,3 — Product Type  
Digit 13 —Voltage  
Motors  
UHP  
Standard motors are 115/60/1, totally  
enclosed, with thermal overload  
1 = 115/60/1*  
2 = 208/60/3  
3 = 230/60/3  
4 = 460/60/3  
5 = 575/60/3 (Totally Enclosed)  
Digit 4 — Development Sequence  
protection for all units through size 280P.  
Standard motors for 42P, 64P and 80P  
are standard pole, sleeve bearing.The  
102P motor is permanent split capacitor  
type with sleeve bearings. Motor for unit  
sizes 122P through 280P are permanent  
split capacitor type with permanently  
lubricated ball bearings. Motors used on  
unit sizes 336P through 720P are 230/460/  
60/3, totally enclosed, with permanently  
lubricated ball bearings. Unit sizes  
smaller than 336P are also available with  
230/460/60/3 motors.  
A
Digits 5,6,7 — Unit Size  
Digit 14 — MotorType  
042  
064  
080  
102  
122  
146  
166  
202  
252  
280  
336  
384  
500  
600  
720  
T =Totally Enclosed*  
E = Explosion Proof  
Digit 15 — Fan Guard  
0 = Standard*  
A = OSHA Guard**  
Digit 16 — Unit Coating  
0 = None  
R = Epoxy  
T = Epoxy Phenollic  
W = Baked Phenolic  
All motors, fractional hp and integral hp,  
have Class “B” insulation.The 115/60/1  
motors used as standard on unit sizes  
42P through 102P can be operated at  
multiple speeds with the addition of a  
solid-state control.  
Digit 17 — Diffuser  
0 = None  
A = Fin Diffuser  
C = Fin Diffuser w/coating  
Digit 8 — CoilType  
P = Steam or Hot Water*  
All units available with explosion-proof  
motors.  
Digit 9 — Fin Series  
Digit 18 — Manual Starter  
4 = 144*  
* Standard features of stock vertical heaters.  
**For the 3-phase and explosion-proof m otors, the OSHA  
guard ships separately.  
0 = None  
A = Manual Starter w/o overload protection  
Digit 10 — Design Sequence  
C
Digit 19 — Speed Controller (115/60/1  
standard motors)  
Digit 11 Tube Material  
0 = None  
D = Solid-State Speed Controller  
(only available up to unit size 102)  
A = Copper*  
C = Red Brass  
F = Steel  
Digit 20 —Thermostats  
Digit 12 — Fin Material  
0 = None  
B = Light-DutyT-stat  
C = Heavy-DutyT-stat  
A = Aluminum*  
C = Copper  
Digit 21 — Subbase  
0 = None  
E = Light-Duty  
F = Heavy-Duty  
UH-PRC001-EN  
21  
Model  
Num ber  
Description  
MODEL S UNIT HEATER  
UHS  
A
0 1 8  
S
2
E
A
A
1
T
A
W
D
A
D
B
E
123  
4
5 6 7  
8
9
10 11 12 13 14 15 16 17 18 19 20 21  
Motors  
Digits 1,2,3 — Product Type  
Digit 13 —Voltage  
Totally enclosed, 115/60/1 Class B”  
insulated, shaded pole and PSC motors  
are STD. 1/25 through 1/8 hp are sleeve  
bearing. 1/6 through 3/4 hp are ball  
bearing. All single phase motors have  
built-in overload protection. Sleeve  
bearing motors can be oiled. Ball  
bearing motors are permanently  
lubricated.The  
115/60/1 motors used as standard on unit  
sizes 18S through 100S can be operated  
at multiple speeds with the addition of a  
solid-state control.  
All units available with explosion-proof  
motors.  
*Standard features of stock horizontal unit heaters.  
**Units equipped with 115 volt totally enclosed m otors  
com e with a standard fan guard/m otor m ount. Units  
equipped with 3 phase or explosion proof m otors com e  
with no guard and the m otors are base m ounted.  
UHS  
1 = 115/60/1*  
2 = 208/60/3  
3 = 230/60/3  
4 = 460/60/3  
5 = 575/60/3 (Totally Enclosed)  
Digit 4— Development Sequence  
A
Digits 5,6,7 — Unit Size  
Digit 14 — MotorType  
Standard  
018  
Modified  
019  
T =Totally Enclosed*  
E = Explosion Proof  
020  
038  
042  
060  
070  
090  
100  
126  
168  
186  
230  
260  
320  
354  
400  
031  
045  
053  
069  
077  
091  
127  
137  
181  
207  
243  
273  
Digit 15 — Motor Mount/Fan Guard  
0 = Standard**  
A = OSHA Fan Guard/Motor Mount (115 volt  
totally enclosed motors ONLY)  
B = Standard Fan Guard with Motor Base (3  
phase or explosion proof motors ONLY)  
Digit 16 — Special Coatings  
0 = No Special Coatings  
R = Epoxy Coating  
T = Epoxy Phenolic Coating  
W = Baked Phenolic Coating  
Digit 17 — Diffuser  
Digit 8 — CoilType  
0 = None  
B = Fin Diffuser  
D = Fin Diffuser w/coating  
S = Steam or Hot Water*  
W = Hot Water (Adds a Spiral)  
Digit 9 — Fin Series  
Digit 18 — Manual Starter  
2 = 132  
8 = 108**  
0 = None  
A = Manual Starter w/o overload protection  
(Single Phase Only)  
DIGIT 10 — Design Sequence  
E
Digit 19 — Speed Controller (115/60/1  
standard motors)  
Digit 11 Tube Material  
0 = None  
D = Solid-State Speed Controller  
(only available up to unit size 100)  
A = Copper*  
C = Red Brass  
F = Steel  
Digit 20 —Thermostats  
Digit 12 — Fin Material  
0 = None  
B = Light-DutyT-stat  
C = Heavy-DutyT-stat  
A = Aluminum*  
C = Copper  
Digit 21 — Subbase  
0 = None  
E = Light-Duty  
F = Heavy-Duty  
22  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-1 – Model S Unit Heater Hot Water Capacities – 60°F Ent. AirTemp.  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
180 F  
200 F  
220 F  
240 F  
Unit  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
Size  
Drop °F MBH GPM  
FT S.W.T. H.W.T. MBH GPM  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
18-S  
5
9.9 4.07 92.4  
7.0 1.45 83.1  
4.2 .58 73.8  
.17  
.03  
.01  
.21  
.03  
.01  
12.0 4.94 99.4  
9.2 1.89 90.1  
.24  
.04  
.01  
.28  
.05  
.01  
14.1 5.81 106.4  
11.3 2.32 97.0  
8.4 1.16 87.7  
.31  
.06  
.02  
.37  
.07  
.02  
16.2 6.69 113.3  
13.4 2.76 104.0  
10.6 1.45 94.7  
.39  
.08  
.03  
.47  
.10  
.03  
CFM 280  
RPM 1075 15  
HP 1/50  
10  
6.3  
.87 80.8  
20-S2  
5
11.8 4.86 94.5  
8.3 1.71 84.2  
.24  
.04  
.01  
.28  
.04  
.01  
14.3 5.90 101.9  
10.8 2.23 91.7  
7.3 1.01 81.5  
.33  
.06  
.01  
.39  
.07  
.02  
16.9 6.95 109.4  
13.4 2.76 99.1  
9.9 1.36 88.9  
.43  
.08  
.02  
51  
.10  
.03  
19.4 8.00 116.8  
15.9 3.28 106.6  
12.4 1.71 96.4  
.54  
.11  
.04  
.64  
.13  
.04  
CFM 315  
10  
RPM 1075 15  
HP 1/50  
4.8  
.66 74.0  
5
25.0 10.30 102.4 1.23  
1.48  
.33  
29.8 12.27 110.5  
26.2 5.40 104.5  
22.6 3.11 98.4  
1.64 1.96  
34.5 14.23 118.6 2.09 2.50  
39.3 16.19 126.7 2.58 3.09  
38-S  
10  
15  
21.4 4.42 96.4  
17.9 2.46 90.3  
14.3 1.47 84.3  
.28  
.10  
.04  
.02  
.38  
.14  
.06  
.03  
.01  
.46  
.17  
31.0 6.38 112.5  
27.4 3.76 106.5  
.51  
.20  
.09  
.05  
.02  
.61  
.24  
.11  
.06  
.03  
35.7 7.36 120.6  
32.2 4.42 114.6  
28.6 2.95 108.5  
25.0 2.06 102.5  
21.5 1.47 96.4  
.64  
26  
.77  
.31  
.15  
.08  
.06  
CFM 543  
.12  
RPM 1550 20  
.05 19.1 1.97 92.4  
.02  
.08 23.8 2.46 10 0.5  
.04  
.02  
.13  
.07  
.04  
HP 1/20  
25  
30  
10.8  
.89 78.2  
15.5 1.28 86.3  
11.9 .82 80.3  
20.3 1.67 94.4  
16.7 1.15 88.4  
5
26.2 10.81 100.9 1.34  
1.61  
.36  
31.2 12.87 108.7  
27.5 5.67 102.9  
23.8 3.26 97.1  
1.78 2.13  
36.2 14.93 116.5 2.28 2.72  
41.2 16.98 124.3 2.81 3.36  
42-S  
10  
15  
22.5 4.64 95.1  
18.8 2.58 89.3  
15.0 1.55 83.5  
.30  
.11  
.42  
.16  
.07  
.03  
.02  
.50  
.19  
32.5 6.69 110.7  
28.8 3.95 104.8  
.55  
.22  
.10  
.05  
.03  
.66  
.26  
.12  
.06  
.03  
37.5 7.72 118.4  
33.7 4.64 112.6  
30.0 3.09 106.8  
26.3 2.17 101.0  
22.6 1.55 95.2  
.70  
28  
.84  
.34  
.17  
.09  
.05  
CFM 591  
.13  
RPM 1550 20  
.04  
.02  
.05 20.0 2.06 91.2  
.02  
.09 25.0 2.58 99.0  
.04  
.02  
.14  
07  
.04  
HP 1/20  
25  
30  
11.3  
.93 77.6  
16.3 1.34 85.4  
12.6 .86 79.6  
21.3 1.76 93.2  
17.6 1.21 87.4  
5
39.0 16.09 104.1 3.40  
4.07  
1.00  
.40  
46.2 19.03 112.2  
42.3 8.72 107.8  
38.4 5.28 103.5  
4.46 5.33  
1.12 1.34  
5.33 21.98 120.3 5.65 6.76  
49.5 10.19 115.9 1.45 1.74  
60-S  
10  
15  
35.2 7.25 99.8  
31.3 4.30 95.4  
27.4 2.83 91.0  
23.6 1.94 86.7  
19.7 1.35 82.3  
.83  
.33  
.16  
.08  
.04  
.01  
56.6 11.67 124.0 1.81 2.17  
CFM 815  
.46  
.23  
.13  
.07  
.02  
.55  
.28 41.7 4.30 107.2  
.15  
.09  
.03  
45.6 6.26 111.6  
.62  
.32  
.18  
.11  
.74  
.38  
.22  
.13  
.05  
52.7 7.25 119.6  
48.9 5.04 115.3  
45.0 3.71 110.9  
41.1 2.83 106.5  
33.4 1.72 97.8  
.78  
.41  
.24  
.15  
.06  
.94  
.49  
.29  
.18  
.07  
RPM 1550 20  
.19 34.6 3.56 99.1  
HP 1/20  
25  
30  
40  
.10  
.05  
.01  
30.7 2.53 94.7  
26.9 1.84 90.4  
37.9 3.12 102.8  
34.0 2.34 98.5  
26.3 1.35 89.7  
12.0  
.62 73.5  
19.1  
.99 81.6  
.04  
5
45.7 18.84 98.3 4.49  
41.1 8.48 94.5 1.10  
5.38  
1.32  
.52  
54.1 22.29 105.3  
49.5 10.21 101.5  
45.0 6.18 97.7  
5.90 7.06  
1.48 1.77  
10  
15  
57.9 11.93 108.5 1.92 2.30  
66.3 13.66 115.5 2.40 2.87  
61.7 8.48 111.7 1.03 1.24  
70-S  
36.6 5.03 90.7  
32.1 3.30 86.9  
27.5 2.27 83.0  
23.0 1.58 79.2  
.44  
.21  
.11  
.06  
.01  
.61  
.30  
.17  
.10  
.73  
.36 48.8 5.03 10 0.9  
.20  
.11  
.04  
53.3 7.33 104.7  
.81  
.42  
.24  
.14  
.05  
.97  
.50  
.28  
.17  
.06  
CFM 1100 20  
RPM 1550 25  
.25 40.4 4.17 93.9  
57.2 5.89 107.9  
52.6 4.34 104.1  
48.1 3.30 100.3  
39.0 2.01 92.7  
.54  
.32  
.20  
.08  
.65  
.38  
.23  
.10  
.13  
.07  
.02  
35.9 2.96 90.1  
31.3 2.15 86.2  
22.2 1.15 78.6  
44.3 3.65 97.1  
39.7 2.73 93.3  
30.6 1.58 85.6  
HP 1/8  
30  
40  
13.9  
.71 71.6  
.03  
10  
15  
20  
53.9 11.10 100.9 2.14  
2.56  
1.08  
64.3 13.25 108.8  
60.0 8.24 105.5  
2.84 3.40  
74.7 15.39 116.7 3.64 4.36  
70.4 9.67 113.4 1.60 1.92  
.78 66.1 6.81 110.2 .86 1.03  
85.1 17.54 124.6 4.50 5.39  
80.8 11.10 121.3 2.01 2.40  
76.5 7.88 118.1 1.10 1.32  
49.6 6.81 97.6  
45.3 4.67 94.4  
41.0 3.38 91.1  
36.7 2.52 87.9  
28.1 1.45 81.3  
.91  
.47  
.26  
.16  
.06  
.02  
1.23 1.47  
90-S  
.56 55.7 5.74 102.3  
.65  
.38  
.24  
.10  
.04  
CFM 1214 25  
RPM 1550 30  
.32  
.19  
.07  
.03  
51.4 4.24 99.0  
47.1 3.24 95.8  
38.5 1.98 89.2  
29.9 1.23 82.7  
.45  
.28  
.12  
.05  
61.8 5.09 106.9  
57.5 3.95 103.7  
48.9 2.52 97.1  
40.3 1.66 90.6  
.52  
.33  
.15  
.07  
.62  
.40  
.18  
.09  
72.2 5.95 114.8  
67.9 4.67 111.6  
59.3 3.06 105.0  
50.7 2.09 98.5  
.67  
.44  
.21  
.11  
.80  
.52  
.25  
.13  
HP 1/8  
40  
50  
19.5  
.80 74.8  
10  
15  
20  
60.6 12.48 96.4 2.63  
55.7 7.65 93.4 1.11  
3.15  
1.33  
72.3 14.90 103.4  
67.4 9.26 100.5  
3.50 4.19  
1.51 1.81  
84.0 17.32 110.5 4.49 5.37  
79.1 10.87 107.5 1.97 2.36  
95.8 19.74 117.5 5.55 6.64  
90.9 12.48 114.6 2.47 2.96  
86.0 8.86 111.6 1.35 1.62  
100-S  
50.8 5.23 90.5  
45.9 3.78 87.5  
41.0 2.82 84.6  
31.2 1.61 78.7  
.57  
.32  
.19  
.07  
.03  
.68 62.5 6.44 97.5  
.80  
.47  
.29  
.12  
.05  
.02  
.95 74.2 7.65 104.6 1.06 1.27  
CFM 1535 25  
RPM 1550 30  
.39  
.23  
.09  
.03  
57.6 4.75 94.6  
52.7 3.62 91.6  
42.9 2.21 85.8  
33.1 1.37 79.9  
.56  
.35  
.15  
.06  
.02  
69.3 5.72 101.6  
64.4 4.43 98.7  
54.6 2.82 92.8  
44.8 1.85 86.9  
35.0 1.20 81.0  
.63  
.40  
.18  
.09  
.04  
.76  
.48  
.22  
.10  
.05  
81.1 6.68 108.7  
76.2 5.23 105.7  
66.4 3.42 99.9  
56.6 2.33 94.0  
46.8 1.61 88.1  
.82  
.53  
.25  
.13  
.07  
.98  
.64  
.30  
.15  
.08  
HP 1/8  
40  
50  
60  
21.4  
.88 72.8  
23.3  
.80 74.0  
10  
15  
20  
80.0 16.48 101.9 5.29  
74.9 10.29 99.2 2.31  
6.33  
2.76  
95.0 19.58 109.7  
89.9 12.36 107.1  
6.97 8.34 110.0 22.68 117.6 8.88 10.62  
3.09 3.70 104.9 14.42 115.0 3.99 4.78  
120.0 16.48 122.8 4.97 5.95  
126-S  
69.8 7.20 96.6 1.23 1.47 84.9 8.74 104.4 1.68 2.01 99.9 10.29 112.3 2.20 2.64 114.9 11.84 120.2 2.77 3.32  
CFM 1760 25  
RPM 1100 30  
64.8 5.34 93.9  
59.7 4.10 91.3  
49.5 2.55 85.9  
39.4 1.62 80.6  
29.2 1.00 75.3  
.73  
.46  
.20  
.09  
.04  
.87  
.55  
.24  
.11  
.05  
79.8 6.58 101.8  
74.7 5.13 99.1  
64.6 3.33 93.8  
54.4 2.24 88.5  
44.3 1.52 83.2  
1.02 1.22  
94.8 7.82 109.6 1.36 1.62  
109.8 9.05 117.5 1.73 2.07  
104.7 7.20 114.9 1.15 1.38  
94.6 4.87 109.5  
84.4 3.48 104.2  
74.3 2.55 98.9  
.66  
.31  
.15  
.08  
.79  
.37  
.19  
.09  
89.7 6.16 107.0  
79.6 4.10 101.7  
69.4 2.86 96.4  
59.3 2.04 91.0  
.89 1.07  
HP 1/6  
40  
50  
60  
.44  
.23  
.13  
.52  
.28  
.15  
.58  
.32  
.19  
.70  
.39  
.22  
UH-PRC001-EN  
23  
Perform ance  
Data  
Table PD-1 (Continued) — Model S Unit Heater Hot Water Capacities – 60°F Ent. AirTemp.  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
15  
20  
25  
180 F  
200 F  
220 F  
240 F  
Unit  
Size  
PD  
FT S.W.T. H.W.T. MBH GPM  
101.4 13.93 99.2 4.60 5.51 121.2 16.66 106.9  
95.5 9.84 97.0 2.50 2.99 115.3 11.88 104.6 3.37 4.04 135.2 13.93 112.3 4.39 5.26 155.0 15.98 120.0 5.50 6.58  
89.6 7.38 94.7 1.51  
83.6 5.75 92.4  
71.8 3.70 87.8  
60.0 2.47 83.2  
48.1 1.65 78.6  
PD  
PD  
FT S.W.T. H.W.T MBH GPM  
6.12 7.33 141.1 19.39 114.6 7.87 9.41  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T.  
161.0 22.12 122.3 9.75 11.67  
PD  
FT S.W.T. H.W.T  
MBH GPM  
168-S  
1.81 109.4 9.02 102.4  
1.17 103.5 7.11 100.1  
2.08 2.48 129.3 10.66 110.0 2.74 3.28  
1.37 1.63 123.4 8.47 107.7 1.83 2.19  
149.1 12.29 117.7 3.47 4.15  
143.2 9.84 115.4 2.34 2.80  
131.4 6.77 110.9 1.21 1.45  
119.5 4.93 106.3  
107.7 3.70 101.7  
CFM 2381 30  
RPM 1100 40  
.97  
.45  
.22  
.11  
.54  
.27  
.13  
91.7 4.72 95.5  
79.8 3.29 90.9  
68.0 2.34 86.3  
.67  
.36  
.20  
.80 111.5 5.75 103.2  
.92 1.11  
.51  
.30  
HP 1/6  
50  
60  
.43  
.23  
99.7 4.11 98.6  
87.9 3.02 94.0  
.61  
.36  
.69  
.42  
.83  
.50  
15  
110.2 15.14 96.2 5.33  
6.38 131.7 18.10 103.2  
7.09 8.48 153.2 21.05 110.3 9.10 10.89  
20 103.9 10.70 94.1 2.90 3.47 125.4 12.92 101.2 3.91 4.68 146.9 15.14 108.2 5.09 6.09 168.4 17.36 115.3 6.37 7.62  
186-S  
25  
97.5 8.04 92.0 1.76  
91.2 6.27 89.9 1.14  
2.10 119.1 9.81 99.1  
1.36 112.7 7.74 97.0  
.63 100.1 5.16 92.8  
2.41 2.88 140.6 11.59 106.1 3.18 3.80  
1.59 1.90 134.3 9.22 104.1 2.13 2.54  
162.1 13.36 113.2 4.02 4.81  
155.8 10.70 111.1 2.72 3.25  
143.1 7.37 107.0 1.41 1.69  
130.5 5.38 102.8  
117.8 4.05 98.7  
CFM 2808 30  
RPM 1100 40  
78.6 4.05 85.8  
65.9 2.72 81.6  
53.3 1.83 77.5  
.53  
.26  
.13  
.78  
.42  
.23  
.93 121.6 6.27 99.9 1.08 1.29  
HP 1/4  
50  
60  
.32  
.16  
87.4 3.60 88.7  
74.8 2.57 84.5  
.50 109.0 4.49 95.8  
.28 96.3 3.31 91.6  
.60  
.35  
.72  
.42  
.81  
.49  
.97  
.59  
15  
142.7 19.61 99.9 1.98  
2.37 171.3 23.53 107.8  
2.65 3.18 199.8 27.46 115.8 3.43 4.10  
228.4 31.38 123.8 4.26 5.10  
20 133.2 13.72 97.2 1.06 1.27 161.7 16.67 105.2 1.44 1.73 190.3 19.61 113.2 1.89 2.26 218.8 22.55 121.1 2.38 2.85  
230-S  
25  
123.6 10.19 94.5  
114.1 7.84 91.9  
95.0 4.89 86.5  
75.8 3.13 81.2  
56.7 1.95 75.9  
.63  
.40  
.17  
.08  
.03  
.75 152.2 12.54 102.5  
.47 142.6 9.80 99.8  
.21 123.5 6.36 94.5  
.10 104.4 4.30 89.2  
.88 1.05 180.7 14.90 110.5 1.17 1.40  
209.3 17.25 118.5 1.49 1.78  
CFM 3299 30  
RPM 1100 40  
.57  
.27  
.13  
.07  
.03  
.68 171.2 11.76 107.8  
.32 152.1 7.84 102.5  
.16 133.0 5.48 97.1  
.08 113.9 3.91 91.8  
.77  
.38  
.20  
.11  
.06  
.92  
.45  
.24  
.13  
.07  
199.7 13.72 115.8  
180.6 9.31 110.5  
161.5 6.66 105.1  
142.4 4.89 99.8  
123.3 3.63 94.5  
.99 1.19  
.50  
.28  
.16  
.10  
.60  
.33  
.19  
.11  
HP 1/4  
50  
60  
70  
.04  
85.3 2.93 83.8  
66.2 1.95 78.5  
.04  
94.8 2.79 86.5  
15  
160.0 21.98 96.0 2.43  
2.91 192.1 26.40 103.2  
3.25 3.89 224.3 30.81 110.4 4.20 5.03  
256.4 35.23 117.7 5.23 6.26  
20 149.0 15.35 93.5 1.29 1.55 181.1 18.67 10 0.7 1.77 2.11 213.3 21.98 108.0 2.32 2.77 245.4 25.29 115.2 2.92 3.49  
260-S  
25  
138.0 11.38 91.0  
127.1 8.73 88.6  
105.1 5.42 83.6  
83.2 3.43 78.7  
61.3 2.10 73.8  
.76  
.48  
.21  
.09  
.04  
.92 170.2 14.03 98.3  
.58 159.2 10.94 95.8  
.25 137.3 7.07 90.9  
.11 115.3 4.75 85.9  
1.07 1.28 202.3 16.68 105.5 1.42 1.70  
234.5 19.33 112.7 1.82 2.17  
223.5 15.35 110.3 1.21 1.45  
CFM 4099 30  
RPM 1100 40  
.69  
.32  
.16  
.08  
.04  
.82 191.4 13.15 103.0  
.38 169.4 8.73 98.1  
.19 147.5 6.08 93.2  
.10 125.6 4.31 88.2  
.05 103.6 3.05 83.3  
.94 1.12  
.46  
.24  
.13  
.07  
.55  
.29  
.16  
.09  
201.6 10.39 105.3  
179.6 7.40 100.4  
157.7 5.42 95.5  
135.8 4.00 90.5  
.61  
.34  
.19  
.11  
.73  
.40  
.23  
.14  
HP 1/2  
50  
60  
70  
.05  
93.4 3.21 81.0  
71.5 2.10 76.1  
15  
205.7 28.26 102.3 4.47  
5.35 245.6 33.75 110.5  
5.93 7.09 285.6 39.24 118.7 7.60 9.10  
325.5 44.73 127.0 9.41 11.27  
20 194.4 20.03 10 0.0 2.44 2.92 234.3 24.15 108.2 3.28 3.93 274.3 28.26 116.4 4.26 5.10 314.2 32.38 124.6 5.33 6.37  
320-S  
30  
171.7 11.79 95.3  
149.0 7.68 90.6  
126.3 5.21 86.0  
103.7 3.56 81.3  
81.0 2.38 76.7  
.97  
.46  
.23  
.12  
.06  
1.16 211.6 14.54 103.5  
.55 189.0 9.74 98.9  
.28 166.3 6.85 94.2  
.14 143.6 4.93 89.5  
.07 120.9 3.56 84.9  
1.34 1.61 251.6 17.28 111.7 1.79 2.15  
291.5 20.03 120.0 2.29 2.74  
268.9 13.85 115.3 1.20 1.43  
CFM 4481 40  
RPM 1100 50  
.67  
.36  
.20  
.12  
06  
.80 228.9 11.79 107.1  
.43 206.2 8.50 102.4  
.24 183.6 6.31 97.8  
.14 160.9 4.74 93.1  
.08 138.2 3.56 88.4  
.92 1.10  
.52  
.30  
.18  
.11  
.62  
.36  
246.2 10.15 110.6  
223.5 7.68 106.0  
.69  
.42  
.27  
.17  
.83  
.51  
.32  
.21  
HP 1/2  
60  
70  
80  
.22 200.8 5.91 101.3  
.13  
98.3 2.53 80.2  
178.2 4.59 96.6  
15  
232.6 31.96 97.9 5.55  
6.65 277.8 38.17 105.2  
7.37 8.82 323.1 44.38 112.6 9.46 11.32  
20 219.6 22.63 95.8 3.03 3.63 264.9 27.30 103.1 4.08 4.88 310.1 31.96 110.5 5.30 6.34 355.4 36.62 117.9 6.62 7.92  
354-S  
30  
193.7 13.31 91.5 1.20  
1.43 239.0 16.42 98.9  
.67 213.1 10.98 94.7  
.34 187.2 7.71 90.5  
.17 161.3 5.54 86.3  
.09 135.3 3.99 82.0  
1.67 1.99 284.2 19.53 106.3 2.22 2.66  
329.5 22.63 113.6 2.84 3.40  
303.5 15.64 109.4 1.48 1.77  
277.6 11.44 105.2  
251.7 8.65 101.0  
225.8 6.65 96.8  
199.9 5.15 92.5  
CFM 5661 40  
RPM 1100 50  
167.8 8.65 87.3  
141.9 5.85 83.1  
116.0 3.99 78.9  
90.1 2.65 74.7  
.56  
.28  
.15  
.07  
.83  
.45  
.25  
.14  
.08  
.99 258.3 13.31 102.1 1.13 1.36  
.53 232.4 9.58 97.8  
.30 206.5 7.09 93.6  
.17 180.6 5.32 89.4  
.09 154.7 3.99 85.2  
.64  
.38  
.23  
.14  
.76  
.45  
.27  
.16  
.86 1.03  
HP 1/2  
60  
70  
80  
.52  
.33  
.21  
.63  
.40  
.25  
109.4 2.82 77.8  
15  
278.0 38.21 101.6 7.36  
8.69 335.0 46.18 110.3 10.06 11.81 391.0 53.74 118.5 12.80 15.14  
20 263.5 27.16 99.4 4.06 4.95 321.0 33.09 108.0 5.79 6.91 379.0 39.07 116.7 7.65 9.02 435.5 44.89 125.1 9.60 11.28  
400-S  
30  
229.0 15.73 94.3 1.52  
1.73 286.0 19.66 102.8  
.88 256.0 13.19 98.3  
.43 227.0 9.36 94.0  
.28 196.0 6.74 89.3  
.13 166.0 4.89 84.8  
2.29 2.59 345.0 23.71 111.6 3.16 3.83  
1.11 1.32 314.0 16.18 107.0 1.61 1.82  
403.0 27.69 120.8 4.21 5.13  
372.0 19.17 115.6 2.17 2.47  
341.0 14.06 111.0 1.26 1.45  
314.0 10.79 107.0  
285.0 8.39 102.6  
CFM 6017 40  
RPM 1140 50  
198.0 10.20 89.5  
168.0 6.93 85.1  
143.0 4.91 81.4  
118.0 3.47 77.7  
.68  
.37  
.21  
.11  
.60  
.34  
.21  
.73 283.0 11.67 102.3  
.42 252.0 8.66 97.7  
.28 222.0 6.54 93.2  
.89 1.07  
HP 3/4  
60  
70  
80  
.53  
.32  
.65  
.41  
.78  
.51  
.92  
.62  
See Table SP-12 for abbreviations.  
24  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-1 (Continued) — Model S Unit Heater Hot Water Capacities – 60°F Ent. AirTemp.  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
260 F  
300 F  
340 F  
380 F  
Unit  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
Size  
Drop °F MBH GPM  
FT S.W.T. H.W.T. MBH GPM  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
18-S  
10  
20  
15.5 3.19 111.0  
.10  
.01  
.12  
.02  
19.7 4.07 124.9  
14.1 1.45 106.3  
.15  
.02  
.00  
.18  
.03  
.01  
24.0 4.94 138.8  
18.3 1.89 120.2  
.21  
.04  
.01  
.25  
.05  
.01  
28.2 5.81 152.7  
22.5 2.32 134.1  
16.9 1.16 115.5  
.27  
.05  
.02  
.00  
.32  
.06  
.02  
.01  
CFM 280  
9.8 1.01 92.3  
RPM 1075 30  
8.4  
.58 87.6  
12.6  
.87 101.5  
HP 1/50  
40  
11.2  
.58 96.8  
10  
20  
30  
40.5 8.34 128.7  
33.4 3.44 116.6  
26.2 1.80 104.5  
.79  
.16  
.05  
.02  
.94  
.20  
.06  
.02  
50.0 10.30 144.9  
42.9 4.42 132.8  
35.7 2.46 120.7  
28.6 1.47 108.6  
1.10 1.32  
.13  
.06  
.03  
.01  
.15  
.07  
.03  
.01  
38-S  
.25  
.09  
.04  
.01  
.30  
.10  
.04  
.02  
CFM 543  
45.3 3.11 136.8  
38.1 1.97 124.7  
31.0 1.28 112.7  
RPM 1550 40  
HP 1/20  
19.1  
.98 92.4  
47.7 2.46 140.9  
40.5 1.67 128.8  
33.4 1.15 116.7  
.08  
04  
02  
10  
.05  
.03  
50  
60  
21.5  
.89 96.5  
23.9  
.82 100.6  
10  
20  
30  
42.5 8.75 126.2  
35.0 3.61 114.6  
27.6 1.89 103.0  
20.1 1.04 91.3  
.86  
.18  
.06  
.02  
1.02  
.21  
.07  
.02  
52.4 10.81 141.8  
45.0 4.64 130.2  
37.5 2.58 118.5  
30.1 1.55 106.9  
1.20 1.43  
.37  
.14  
.06  
.03  
.01  
.44  
.17  
.07  
.04  
.02  
42-S  
.27  
.10  
.04  
.02  
.32  
.11  
.05  
.02  
55.0 5.67 145.7  
47.5 3.26 134.1  
40.1 2.06 122.5  
32.6 1.34 110.9  
CFM 591  
RPM 1550 40  
HP 1/20  
50.1 2.58 138.1  
42.6 1.76 126.4  
35.1 1.21 114.8  
.09  
.05  
.02  
.11  
.05  
.03  
50  
60  
22.6  
.93 95.3  
25.2  
.86 99.2  
20  
30  
40  
50  
56.0 5.77 123.4  
48.3 3.32 114.6  
40.6 2.09 105.9  
32.8 1.35 97.1  
.51  
.19  
.09  
.04  
.02  
.62  
.23  
.10  
.05  
.02  
70.3 7.25 139.5  
62.6 4.30 130.8  
54.9 2.83 122.0  
47.1 1.94 113.3  
39.4 1.35 104.6  
.74  
.30  
.14  
.07  
.04  
.89  
.35  
.17  
.09  
.05  
.20  
.11  
.06  
.02  
.25  
.13  
.08  
.03  
60-S  
69.2 3.56 138.2  
61.4 2.53 129.5  
53.7 1.84 120.7  
CFM 815  
75.7 3.12 145.6  
68.0 2.34 136.9  
52.5 1.35 119.4  
.16  
.09  
.04  
.01  
.19  
.11  
.04  
.02  
RPM 1550 60  
HP 1/20  
25.1  
.86 88.4  
80  
100  
38.3  
.99 103.3  
37.1  
.76 101.9  
20  
30  
40  
65.5 6.75 114.9  
56.4 3.88 107.3  
47.4 2.44 99.7  
38.3 1.58 92.1  
29.2 1.00 84.4  
.68  
.26  
.11  
.05  
.02  
.81  
.31  
.14  
.06  
.03  
82.3 8.48 129.0  
73.2 5.03 121.3  
64.1 3.30 113.7  
55.0 2.27 106.1  
45.9 1.58 98.5  
.98 1.17  
99.0 10.21 143.0 1.31 1.56  
.36  
.21  
.12  
.05  
.02  
.43  
.25  
.15  
.06  
.02  
.39  
.19  
.10  
.05  
.01  
.47  
.22  
.12  
.06  
.02  
89.9 6.18 135.4  
80.8 4.17 127.7  
71.8 2.96 120.1  
62.7 2.15 112.5  
44.5 1.15 97.2  
.54  
.27  
.15  
.08  
.03  
.65  
.32  
.18  
.10  
.03  
70-S  
97.6 5.03 141.8  
88.5 3.65 134.2  
79.4 2.73 126.5  
61.2 1.58 111.3  
CFM 1100 50  
RPM 1550 60  
HP 1/8  
80  
100  
27.7  
.71 83.2  
43.0  
.89 96.0  
40  
50  
69.7 3.59 112.9  
61.1 2.52 106.4  
52.6 1.81 99.9  
.27  
.15  
.08  
.02  
.32  
.17  
.10  
.03  
90.6 4.67 128.7  
82.0 3.38 122.2  
73.4 2.52 115.7  
56.2 1.45 102.7  
.41  
.24  
.14  
.05  
.02  
.50  
.34  
.21  
.09  
.04  
.02  
.40  
.25  
.11  
.05  
.02  
.29  
.13  
.06  
.03  
.34  
.16  
.08  
.04  
90-S  
.28 102.8 4.24 138.0  
CFM 1214 60  
RPM 1550 80  
.17  
.06  
.02  
94.2 3.24 131.5  
77.0 1.98 118.5  
59.8 1.23 105.4  
115.0 3.95 147.3  
97.8 2.52 134.3  
80.7 1.66 121.2  
63.5 1.09 108.2  
35.4  
.91 86.9  
HP 1/8  
100  
120  
39.0  
.80 89.6  
42.7  
.73 92.4  
40  
50  
60  
78.1 4.02 106.9  
68.3 2.82 101.0  
58.5 2.01 95.1  
38.9 1.00 83.4  
.33  
.18  
.10  
.03  
.01  
.40 101.6 5.23 121.0  
.51  
.29  
.17  
.06  
.02  
.61 125.0 6.44 135.1  
.34 115.2 4.75 129.2  
.20 105.4 3.62 123.3  
.71  
.41  
.26  
.11  
.05  
.02  
.01  
.84  
.49  
.31  
.13  
.06  
.02  
.01  
.55  
.35  
.16  
.08  
.04  
.02  
.66  
.42  
.19  
.09  
.04  
.02  
.21  
.12  
.03  
.01  
91.8 3.78 115.1  
82.0 2.82 109.2  
62.4 1.61 97.4  
138.7 5.72 143.3  
128.9 4.43 137.4  
109.3 2.82 125.6  
89.7 1.85 113.9  
70.1 1.20 102.1  
100-S  
CFM 1535 80  
RPM 1550 100  
.08  
.03  
85.8 2.21 111.5  
66.2 1.37 99.8  
19.3  
.40 71.6  
42.8  
.88 85.7  
HP 1/8  
120  
140  
46.6  
27.0  
.80 88.0  
.40 76.2  
50.5  
.74 90.3.  
50  
60  
80  
99.5 4.10 112.1  
89.3 3.07 106.8  
69.0 1.78 96.1  
48.7 1.00 85.5  
.42  
.25  
.10  
.04  
.01  
.51 129.5 5.34 127.8  
.30 119.4 4.10 122.5  
.65  
.41  
.18  
.08  
.03  
.78 159.6 6.58 143.6  
.49 149.4 5.13 138.2  
.21 129.1 3.33 127.6  
.10 108.8 2.24 117.0  
.90 1.08  
.38  
.20  
.11  
.06  
.03  
.46  
.24  
.14  
.07  
.04  
.59  
.27  
.14  
.07  
.03  
.01  
.70  
.33  
.17  
.08  
.04  
.02  
126-S  
.12  
.04  
.01  
99.1 2.55 111.9  
78.8 1.62 101.3  
58.5 1.00 90.6  
159.2 4.10 143.3  
138.9 2.86 132.7  
118.6 2.04 122.1  
98.3 1.45 111.5  
78.0 1.00 100.8  
CFM 1760 100  
RPM 1100 120  
28.4  
.49 74.9  
.04  
88.5 1.52 106.4  
68.2 1.00 95.7  
HP 1/6  
140  
160  
47.9  
.62 85.1  
40  
50  
60  
151.2 7.79 118.5 1.53  
1.83 191.0 9.84 133.9  
1.07 179.1 7.38 129.3  
.67 167.3 5.75 124.8  
.28 143.6 3.70 115.6  
.12 120.0 2.47 106.4  
2.23 2.66  
139.4 5.75 114.0  
127.6 4.38 109.4  
103.9 2.68 100.2  
80.2 1.65 91.1  
.90  
.56  
.23  
.10  
.04  
1.35 1.61 218.8 9.02 144.7 1.84 2.21  
168-S  
.87 1.04 207.0  
7.11 140.1 1.22 1.46  
CFM 2381 80  
RPM 1100 100  
.40  
.20  
.10  
.05  
02  
.48 183.3 4.72 131.0  
.60  
.32  
.17  
.10  
.05  
.02  
.71  
.38  
.21  
.11  
.06  
.03  
223.0 5.75 146.3  
199.4 4.11 137.2  
175.7 3.02 128.0  
152.1 2.24 118.9  
128.4 1.65 109.7  
104.7 1.20 100.5  
.81  
.45  
.26  
.16  
.09  
.05  
.97  
.54  
.32  
.19  
.11  
.06  
.24 159.7 3.29 121.8  
.12 136.0 2.34 112.6  
.05 112.3 1.65 103.5  
HP 1/6  
120  
140  
160  
180  
56.6  
.97 81.9  
.05  
96.3 1.65 97.3  
72.6 1.07 88.1  
49.0  
.63 79.0  
.02  
88.7 1.14 94.3  
65.0 .74 85.2  
UH-PRC001-EN  
25  
Perform ance  
Data  
Table PD-1 (Continued) — Model S Unit Heater Hot Water Capacities – 60°F Ent. AirTemp.  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
40  
50  
60  
80  
260 F  
300 F  
340 F  
380 F  
Unit  
Size  
PD  
FT S.W.T. H.W.T. MBH GPM  
164.7 8.48 114.0 1.78 2.13 207.7 10.70 128.2  
152.0 6.27 109.9 1.04  
139.4 4.79 105.7  
114.1 2.94 97.4  
88.8 1.83 89.1  
63.5 1.09 80.8  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
2.58 3.09 250.8 12.92 142.3 3.47 4.15  
1.56 1.87 238.1 9.81 138.2 2.14 2.56  
1.01 1.21 225.5 7.74 134.0 1.42 1.69  
1.25 195.1 8.04 124.0  
.78 182.4 6.27 119.9  
.33 157.1 4.05 111.6  
.14 131.8 2.72 103.3  
.06 106.5 1.83 95.0  
.65  
.28  
.12  
.05  
186-S  
.47  
.23  
.12  
.06  
.02  
.56 200.2 5.16 125.7  
.28 174.9 3.60 117.4  
.14 149.6 2.57 109.1  
.07 124.3 1.83 100.8  
.70  
.37  
.21  
.11  
.06  
.03  
.83  
.45  
.25  
.14  
.07  
.04  
243.2 6.27 139.8  
217.9 4.49 131.5  
192.6 3.31 123.2  
167.3 2.46 114.9  
142.0 1.83 106.6  
116.7 1.34 98.3  
.94 1.13  
CFM 2808 100  
RPM 1100 120  
.53  
.31  
.19  
.11  
.06  
.63  
.37  
.22  
.13  
.08  
HP 1/4  
140  
160  
180  
81.2 1.20 86.7  
55.9  
.72 78.4  
.03  
99.0 1.28 92.5  
73.7  
.84 84.2  
40  
50  
60  
209.2 10.78 118.4  
190.1 7.84 113.1  
171.0 5.87 107.8  
132.8 3.42 97.1  
94.6 1.95 86.4  
.64  
.36  
.22  
.09  
.03  
.76 266.3 13.72 134.4  
.44 247.2 10.19 129.1  
.26 228.1 7.84 123.7  
.10 189.9 4.89 113.1  
.04 151.7 3.13 102.4  
.94 1.13  
.78  
.50  
.24  
.12  
.06  
.03  
.01  
.93  
.60  
.28  
.14  
.07  
.04  
.02  
.56  
.35  
.15  
.07  
.03  
.67 304.3 12.54 145.0  
.42 285.2 9.80 139.7  
.19 247.0 6.36 129.0  
.08 208.8 4.30 118.3  
.04 170.6 2.93 107.7  
230-S  
CFM 3299 80  
RPM 1100 100  
304.1 7.84 145.0  
265.9 5.48 134.3  
227.7 3.91 123.6  
189.5 2.79 112.9  
151.3 1.95 102.3  
.33  
.18  
.10  
.05  
.03  
.39  
.21  
.12  
.07  
.04  
HP 1/4  
120  
140  
160  
113.5 1.95 91.7  
13.4 1.95 97.0  
94.2 1.21 86.3  
40  
50  
60  
233.7 12.04 112.5  
211.8 8.73 107.6  
189.8 6.52 102.7  
146.0 3.76 92.8  
102.1 2.10 83.0  
.78  
.44  
.26  
.10  
.04  
.93 298.0 15.35 127.0  
.53 276.1 11.38 122.1  
.32 254.1 8.73 117.1  
.12 210.3 5.42 107.3  
.04 166.4 3.43 97.4  
1.15 1.38 362.3 18.67 141.5 1.57 1.87  
.68  
.43  
.19  
.08  
.04  
.81 340.3 14.03 136.5  
.51 318.4 10.94 131.6  
.22 274.6 7.07 121.7  
.10 230.7 4.75 111.9  
.04 186.8 3.21 102.0  
.95 1.14  
260-S  
.61  
.29  
.14  
.07  
.03  
.01  
.73  
.34  
.17  
.09  
.04  
.02  
382.7 13.15 146.1  
338.8 8.73 136.2  
295.0 6.08 126.3  
251.1 4.31 116.5  
207.2 3.05 106.6  
163.4 2.10 96.7  
.82  
.40  
.21  
.12  
.06  
.03  
.98  
.48  
.25  
.14  
.08  
.04  
CFM 4099 80  
RPM 1100 100  
HP 1/2  
120  
140  
160  
122.5 2.10 87.6  
143.0 2.10 92.1  
99.1 1.28 82.3  
40  
50  
60  
80  
308.8 15.91 123.5 1.50  
1.80 388.7 20.03 140.0  
1.06 366.0 15.09 135.3  
.67 343.4 11.79 130.6  
.29 298.0 7.68 121.3  
.13 252.7 5.21 112.0  
.06 207.3 3.56 102.6  
2.17 2.60  
1.32 1.58  
.86 1.03  
286.1 11.79 118.9  
263.5 9.05 114.2  
218.1 5.62 104.9  
172.8 3.56 95.5  
127.4 2.19 86.2  
.89  
.56  
.24  
.11  
.05  
320-S  
.41  
.21  
.11  
.05  
.02  
.49 377.9 9.74 137.7  
.25 332.6 6.85 128.4  
.13 287.2 4.93 119.1  
.06 241.9 3.56 109.8  
.03 196.5 2.53 100.4  
.59  
.32  
.18  
.10  
.06  
.03  
.71  
.39  
.22  
.12  
.07  
.04  
CFM 4481 100  
RPM 1100 120  
412.5 8.50 144.8  
367.1 6.31 135.5  
321.8 4.74 126.2  
276.4 3.56 116.9  
231.1 2.65 107.5  
.45  
.27  
.16  
.10  
.06  
.54  
.32  
.20  
.12  
.07  
HP 1/2  
140  
160  
180  
162.0 2.38 93.3  
116.6 1.50 84.0  
151.2 1.73 91.1  
50  
60  
80  
322.9 13.31 112.6 1.10  
1.32 413.4 17.04 127.3  
.83 387.5 13.31 123.1  
.36 335.6 8.65 114.6  
.16 283.8 5.85 106.2  
.07 232.0 3.99 97.8  
1.64 1.96 503.8 20.77 142.0 2.24 2.68  
1.06 1.27 477.9 16.42 137.8 1.48 1.78  
297.0 10.20 108.4  
245.2 6.32 99.9  
193.4 3.99 91.5  
141.5 2.43 83.0  
.69  
.30  
.13  
.06  
354-S  
.50  
.25  
.13  
.06  
.03  
.60 426.1 10.98 129.4  
.30 374.3 7.71 120.9  
.15 322.5 5.54 112.5  
.08 270.7 3.99 104.1  
.03 218.9 2.82 95.6  
.74  
.40  
.22  
.13  
.07  
.03  
.88  
.48  
.27  
.15  
.08  
.04  
516.6 13.31 144.1  
464.8 9.58 135.7  
413.0 7.09 127.2  
361.2 5.32 118.8  
309.4 3.99 110.4  
257.6 2.95 101.9  
.99 1.19  
CFM 5661 100  
RPM 1100 120  
.56  
.33  
.20  
.12  
.07  
.67  
.40  
.24  
.15  
.09  
HP 1/2  
140  
160  
180  
180.2 2.65 89.3  
128.4 1.65 80.9  
167.1 1.91 87.2  
50  
60  
80  
400.0 16.49 119.8 1.67  
371.0 12.75 115.5 1.02  
1.88 520.0 21.44 137.8  
1.23 490.0 16.83 133.3  
.54 425.0 10.95 123.6  
.28 362.0 7.46 114.1  
.19 300.0 4.15 104.9  
2.66 3.11 641.0 26.43 155.9 3.88 4.71  
1.71 1.94 610.0 20.96 151.7 2.56 2.96  
400-S  
306.0 7.88 105.8  
244.0 5.03 96.5  
180.0 3.09 86.9  
.46  
.21  
.18  
.81  
.41  
.22  
.13  
.04  
.95 540.0 13.91 140.8 1.22 1.42  
662.0 17.06 159.0 1.80 2.61  
CFM 6017 100  
RPM 1140 120  
.52 478.0 9.85 131.5  
.30 415.0 7.13 122.1  
.15 350.0 5.15 112.3  
.05 285.0 3.67 192.6  
.67  
.37  
.21  
.13  
.04  
.80  
.48  
.29  
.15  
.05  
596.0 12.28 149.1  
530.0 9.10 139.3  
461.0 6.78 129.0  
394.9 5.08 118.9  
325.0 3.72 108.6  
.98 1.18  
.57  
.35  
.21  
.12  
.71  
.42  
.30  
.13  
HP 3/4  
140  
160  
180  
235.0 3.46 95.1  
171.0 2.20 85.6  
220.0 2.52 92.9  
26  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-2 – Model S Unit Heater Hot Water Capacities – 60°F Ent. AirTemp. Hot Water with Turbulators and 132 Fin Series  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
5
10  
15  
180 F  
200 F  
220 F  
240 F  
Unit  
Size  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T.  
.91 1.08  
PD  
FT S.W.T. H.W.T. MBH GPM  
13.2 5.45 98.7  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
.46  
.11  
.04  
.02  
.01  
.56  
.14  
.05  
15.7 6.47 106.0  
14.0 2.88 100.9  
12.2 1.68 95.8  
.66  
.15  
.06  
.03  
.01  
.01  
.72  
.18  
.07  
18.2 7.50 113.2  
16.5 3.39 108.2  
14.7 2.02 103.1  
.75  
.20  
.08  
.04  
.02  
.01  
.90  
.23  
.10  
.05  
.03  
.01  
20.7 8.53 120.5  
18.9 3.91 115.4  
17.2 2.36 110.4  
15.5 1.59 105.3  
13.7 1.13 100.2  
20-W2  
CFM 315  
11.5 2.36 93.6  
9.7 1.34 88.5  
.24  
.10  
.29  
.12  
.06  
.04  
.02  
RPM 1075 20  
8.0  
6.3  
.82 83.4  
.02 10.5 1.08 90.7  
.04 13.0 1.34 98.0  
.05  
.03  
.02  
HP 1/50  
25  
30  
.52 78.3  
.01  
8.7  
7.0  
.72 85.6  
.48 80.5  
.02  
.01  
11.2  
9.5  
.93 92.9  
.65 87.8.  
12.0  
.82 95.1  
5
10  
15  
28.4 11.71 110.9 2.70  
3.22  
.89  
.40  
.21  
.13  
33.5 13.80 120.0  
31.4 6.47 116.3  
29.3 4.03 112.5  
27.2 2.80 108.8  
25.1 2.07 105.0  
23.0 1.58 101.3  
3.41 4.07  
.96 1.15  
38.6 15.89 129.1 4.21 5.03  
36.5 7.52 125.4 1.20 1.43  
43.6 17.99 138.3 5.05 6.03  
41.6 8.56 134.5 1.45 1.74  
38-W2  
26.3 5.42 107.2  
24.2 3.33 103.4  
22.1 2.28 99.7  
20.0 1.65 95.9  
17.9 1.23 92.2  
.75  
.33  
.18  
.11  
CFM 514  
.44  
.24  
.14  
.52  
.28 32.3 3.33 117.9  
34.4 4.72 121.6  
.55  
.31  
.19  
.66  
.37  
.23  
.15  
39.5 5.42 130.8  
37.4 3.85 127.0  
35.3 2.91 123.2  
33.2 2.28 119.5  
.68  
.38  
.24  
.16  
.81  
.46  
.29  
.19  
RPM 1550 20  
HP 1/20  
25  
30  
.17  
.11  
30.2 2.49 114.1  
28.1 1.93 110.4  
.07  
.08  
.09  
.13  
5
10  
15  
20  
28.8 11.89 110.2 2.77  
3.31  
.92  
.41  
.22  
.13  
.08  
.03  
34.0 14.02 119.1  
31.9 6.57 115.4  
29.8 4.09 111.8  
27.6 2.85 108.1  
25.5 2.10 104.4  
23.4 1.61 100.7  
3.50 4.18  
.99 1.18  
39.2 16.14 128.1 4.32 5.16  
37.0 7.63 124.4 1.23 1.47  
44.3 18.27 137.1 5.18 6.19  
42.2 8.70 133.4 1.49 1.78  
26.7 5.51 106.5  
24.6 3.38 102.8  
22.5 2.32 99.1  
20.4 1.68 95.4  
18.2 1.25 91.7  
.77  
.34  
.18  
.11  
.07  
.03  
42-W2  
.45  
.24  
.15  
.10  
.53  
.29 32.8 3.38 117.0  
34.9 4.80 120.7  
.57  
.32  
.20  
.13  
.06  
.68  
.38  
.23  
.15  
.07  
40.1 5.51 129.7  
38.0 3.91 126.0  
35.8 2.95 122.3  
33.7 2.32 118.6  
29.5 1.52 111.3  
.70  
.39  
.25  
.17  
.08  
.83  
.47  
.29  
.20  
.10  
CFM 530  
RPM 1550 25  
HP 1/20  
.18  
.11  
.05  
30.7 2.53 113.4  
28.6 1.96 109.7  
24.3 1.25 102.3  
30  
40  
14.0  
.72 84.3  
19.2  
.99 93.3  
.04  
10  
15  
20  
25  
40.4 8.33 109.3 2.10  
2.50  
1.16  
47.9 9.88 118.5  
45.5 6.25 115.6  
2.66 3.17  
55.5 11.43 127.7 3.30 3.94  
53.1 7.29 124.8 1.56 1.86  
.84 50.6 5.22 121.8 .90 1.07  
63.0 12.99 136.9 3.97 4.73  
60.6 8.33 134.0 1.89 2.26  
58.2 6.0 0 131.0 1.10 1.31  
38.0 5.22 106.4  
35.6 3.67 103.4  
33.1 2.73 100.5  
30.7 2.11 97.5  
25.9 1.33 91.6  
.97  
.54  
.34  
.22  
.10  
1.24 1.48  
60-W2  
.65 43.1 4.44 112.6  
.71  
.44  
.30  
.15  
.08  
CFM 755  
.40  
.26  
.13  
.06  
40.7 3.35 109.7  
38.3 2.63 106.7  
33.4 1.72 100.8  
28.6 1.18 94.9  
.53  
.36  
.18  
.10  
48.2 3.98 118.9  
45.8 3.15 115.9  
41.0 2.11 110.0  
36.1 1.49 104.1  
.57  
.39  
.20  
.11  
.68  
.46  
.24  
.14  
55.8 4.60 128.1  
53.3 3.67 125.1  
48.5 2.50 119.2  
43.7 1.80 113.3  
.71  
.49  
.26  
.15  
.85  
.58  
.31  
.18  
RPM 1550 30  
HP 1/20  
40  
50  
21.1  
.87 85.7  
.05  
10  
15  
20  
46.3 9.54 102.5 2.63  
43.6 5.99 100.0 1.22  
3.14  
1.45  
54.9 11.32 110.4  
52.2 7.17 107.9  
3.33 3.98  
1.56 1.86  
63.5 13.10 118.3 4.14 4.94  
60.8 8.36 115.8 1.96 2.34  
72.2 14.87 126.2 4.97 5.94  
69.4 9.54 123.7 2.38 2.84  
66.7 6.88 121.2 1.38 1.65  
70-W2  
40.8 4.21 97.5  
38.1 3.14 95.0  
35.4 2.43 92.5  
30.0 1.54 87.5  
24.5 1.01 82.5  
.68  
.42  
.28  
.13  
.07  
.03  
.82 49.5 5.10 105.4  
.89 1.06 58.1 5.99 113.3 1.13 1.35  
CFM 1004 25  
RPM 1550 30  
.51  
.33  
.16  
.08  
.04  
46.7 3.85 102.9  
44.0 3.02 100.4  
38.6 1.99 95.4  
33.1 1.37 90.4  
.56  
.38  
.19  
.10  
.06  
.67  
.45  
.23  
.12  
.07  
55.4 4.56 110.8  
52.6 3.62 108.3  
47.2 2.43 103.3  
41.8 1.72 98.3  
36.3 1.25 93.3  
.72  
.49  
.26  
.15  
.09  
.86  
.59  
.31  
.17  
.10  
64.0 5.28 118.7  
61.3 4.21 116.2  
55.8 2.88 111.2  
50.4 2.08 106.2  
44.9 1.54 101.3  
.89 1.06  
.61  
.33  
.19  
.12  
.73  
.39  
.23  
.14  
HP 1/8  
40  
50  
60  
19.1  
.65 77.5  
27.7  
.95 85.4  
UH-PRC001-EN  
27  
Perform ance  
Data  
Table PD-2 (Continued) – Model S Unit Heater Hot Water Capacities – 60°F Ent. AirTemp. Hot Water with Turbulators and 132 Fin Series  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
10  
15  
20  
180 F  
200 F  
220 F  
240 F  
Unit  
Size  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T. MBH GPM  
FT S.W.T. H.W.T MBH GPM  
72.1 14.85 117.2  
69.1 9.50 114.8  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
60.9 12.56 108.3 5.44  
58.0 7.97 106.0 2.58  
6.49  
3.08  
6.84 8.17  
3.27 3.90  
83.2 17.15 126.0 8.45 10.08  
80.3 11.03 123.7 4.07 4.86  
77.3 7.97 121.3 2.38 2.84  
74.4 6.13 119.0 1.55 1.85  
71.5 4.91 116.7 1.07 1.28  
91.4 12.56 132.5 4.91 5.85  
88.5 9.12 130.2 2.89 3.45  
85.5 7.05 127.8 1.90 2.26  
82.6 5.67 125.5 1.33 1.58  
90-W2  
55.1 5.67 103.7 1.48 1.77 66.2 6.82 112.5 1.89 2.26  
CFM 1162 25  
RPM 1550 30  
52.1 4.30 101.3  
49.2 3.38 99.0  
43.3 2.23 94.4  
37.5 1.54 89.7  
31.6 1.09 85.1  
.94  
.64  
.33  
.18  
.10  
1.12  
.76  
.39  
.22  
.12  
63.3 5.22 110.2  
60.3 4.14 107.9  
54.5 2.81 103.2  
48.6 2.00 98.5  
42.7 1.47 93.9  
1.22 1.45  
.84 1.00  
.45  
.26  
.16  
HP 1/8  
40  
50  
60  
.53  
.31  
.19  
65.6 3.38 112.0  
59.7 2.46 107.4  
53.9 1.85 102.7  
.58  
.35  
.22  
.70  
.42  
.26  
76.7 3.95 120.9  
70.9 2.92 116.2  
65.0 2.23 111.6  
.73  
.45  
.29  
.88  
.53  
.35  
10  
15  
20  
67.3 13.87 103.5 6.42  
64.0 8.79 101.3 3.04  
7.66  
79.6 16.40 111.4  
76.3 10.49 109.3  
8.07 9.63  
3.85 4.60  
3.62  
88.6 12.18 117.2 4.80 5.73  
100.9 13.87 125.2 5.79 6.90  
97.7 10.06 123.1 3.41 4.07  
94.4 7.78 121.0 2.23 2.66  
91.1 6.26 118.8 1.56 1.86  
100-W2  
60.7 6.26 99.2 1.74 2.08 73.0 7.53 107.2 2.23 2.66 85.3 8.79 115.1 2.91 3.35  
CFM 1427 25  
RPM 1550 30  
57.5 4.74 97.1 1.11  
1.32  
.89  
.46  
.25  
.14  
69.8 5.75 105.1  
66.5 4.57 102.9  
59.9 3.09 98.7  
53.4 2.20 94.5  
46.9 1.61 90.3  
1.43 1.71  
.98 1.17  
82.1 6.77 113.0 1.82 2.17  
78.8 5.41 110.9 1.26 1.51  
72.3 3.72 106.7  
65.7 2.71 102.4  
59.2 2.03 98.2  
54.2 3.72 95.0  
47.6 2.45 90.8  
41.1 1.69 86.5  
34.6 1.19 82.3  
.75  
.38  
.21  
.12  
HP 1/8  
40  
50  
60  
.52  
.30  
.18  
.63  
.36  
.22  
.68  
.41  
.26  
.82  
.49  
.30  
84.6 4.36 114.6  
78.0 3.22 110.4  
71.5 2.45 106.2  
.86 1.03  
.53  
.34  
.63  
.40  
15  
20  
25  
84.8 11.66 107.1 6.44  
7.68 100.8 13.86 116.0  
8.10 9.66 116.8 16.05 124.8 10.04 11.98  
132.8 18.25 133.7 12.05 14.38  
81.1 8.36 105.0 3.75 4.47  
97.1 10.01 113.9 4.75 5.66 113.1 11.66 122.8 5.93 7.03 129.1 13.31 131.6 7.17 8.55  
126-W2  
77.4 6.38 102.9 2.42  
73.7 5.06 100.9 1.66  
2.88  
1.98  
1.05  
.61  
93.4 7.70 111.8  
89.7 6.16 109.8  
82.2 4.24 105.6  
74.8 3.08 101.5  
67.3 2.31 97.3  
3.09 3.69 109.4 9.02 120.7 3.90 4.65  
2.15 2.57 105.7 7.26 118.6 2.73 3.26  
125.4 10.34 129.6 4.74 5.65  
121.7 8.36 127.5 3.35 3.99  
114.2 5.88 123.4 1.89 2.25  
106.8 4.40 119.2 1.18 1.41  
CFM 1661 30  
RPM 1100 40  
66.2 3.41 96.7  
58.8 2.42 92.6  
51.3 1.76 88.5  
.88  
.51  
.31  
1.18 1.41  
98.2 5.06 114.5 1.52 1.81  
HP 1/6  
50  
60  
.71  
.45  
.85  
.54  
90.8 3.74 110.4  
83.3 2.86 106.2  
.93 1.11  
.60 .72  
.37  
99.3 3.41 115.1  
.78  
.93  
20 108.7 11.20 104.2 7.45 8.89 129.8 13.37 112.8 9.39 11.20 150.9 15.55 121.4 11.70 13.95 172.1 17.73 130.0 14.09 16.81  
168-W2  
25  
104.1 8.58 102.3 4.85  
99.6 6.84 100.5 3.37  
90.5 4.66 96.8 1.82  
81.4 3.36 93.1 1.08  
5.78 125.3 10.33 110.9  
4.01 120.7 8.29 109.1  
2.17 111.6 5.75 105.4  
1.29 102.6 4.23 101.7  
6.16 7.34 146.4 12.07 119.5 7.73 9.22  
4.32 5.15 141.9 9.75 117.7 5.45 6.50  
2.41 2.87 132.8 6.84 114.0 3.07 3.66  
1.48 1.76 123.7 5.10 110.3 1.91 2.27  
.96 1.14 114.6 3.94 106.6 1.26 1.50  
167.5 13.81 128.1 9.36 11.17  
163.0 11.20 126.3 6.65 7.93  
153.9 7.93 122.6 3.80 4.53  
144.8 5.97 118.9 2.40 2.86  
135.8 4.66 115.2 1.61 1.92  
CFM 2267 30  
RPM 1100 40  
HP 1/6  
50  
60  
72.4 2.49 89.4  
.67  
.80  
93.5 3.21 98.0  
28  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-2 (Continued) – Model S Unit Heater Hot Water Capacities – 60°F Ent. AirTemp. Hot Water with Turbulators and 132 Fin Series  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
20  
25  
30  
180 F  
200 F  
220 F  
240 F  
Unit  
Size  
PD  
FT S.W.T. H.W.T. MBH GPM  
117.6 12.12 10 0.3 8.49 10.12 140.5 14.48 108.1 10.71 12.77 163.4 16.84 116.0 13.33 15.90  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
112.7 9.29 98.6 5.52  
107.8 7.41 96.9 3.83  
98.0 5.05 93.6 2.08  
88.2 3.63 90.2 1.23  
6.59 135.6 11.18 106.5  
4.57 130.7 8.98 104.8  
2.47 120.9 6.23 101.4  
1.47 111.0 4.58 98.0  
.91 101.2 3.48 94.7  
7.01 8.36 158.5 13.06 114.3 8.81 10.50  
4.92 5.87 153.5 10.55 112.6 6.21 7.41  
2.74 3.27 143.7 7.41 109.2 3.50 4.17  
1.68 2.01 133.9 5.52 105.9 2.17 2.59  
1.09 1.30 124.1 4.26 102.5 1.43 1.70  
181.3 14.95 122.1 10.67 12.73  
176.4 12.12 120.4 7.58 9.04  
166.6 8.58 117.1 4.33 5.16  
156.8 6.46 113.7 2.73 3.26  
147.0 5.05 110.4 1.83 2.19  
137.1 4.04 107.0 1.28 1.53  
186-W2  
CFM 2690 40  
RPM 1100 50  
HP 1/4  
60  
70  
80  
78.3 2.69 86.8  
68.5 2.02 83.5  
.76  
.48  
.58  
91.4 2.69 91.3  
81.6 2.10 87.9  
.73  
.49  
.87 114.3 3.36 99.1  
.59 104.4 2.69 95.8  
.98 1.17  
.69 .82  
127.3 3.28 103.6  
.92 1.09  
15  
163.8 22.50 107.2 5.82  
6.94 194.7 26.75 116.1  
7.32 8.73 225.6 30.99 125.0 9.07 10.81  
256.4 35.24 133.9 10.88 12.97  
20 156.6 16.14 105.1 3.39 4.04 187.5 19.32 114.0 4.29 5.12 218.4 22.50 122.9 5.36 6.40 249.2 25.69 131.8 6.47 7.72  
230-W2  
25  
149.4 12.32 103.0 2.19  
142.2 9.77 101.0 1.51  
2.61 180.3 14.86 111.9  
1.80 173.1 11.89 109.9  
.96 158.7 8.18 105.7  
.55 144.3 5.95 101.6  
.33 129.9 4.46 97.4  
.20 115.6 3.40 93.3  
2.80 3.33 211.2 17.41 120.8 3.52 4.20  
1.95 2.33 204.0 14.01 118.7 2.47 2.95  
1.07 1.28 189.6 9.77 114.6 1.38 1.64  
242.1 19.96 129.7 4.28 5.11  
234.9 16.14 127.6 3.03 3.61  
220.5 11.36 123.5 1.71 2.04  
206.1 8.50 119.4 1.07 1.27  
CFM 3200 30  
RPM 1100 40  
127.8 6.59 96.8  
113.4 4.68 92.7  
99.0 3.40 88.5  
84.7 2.49 84.4  
.80  
.46  
.28  
.17  
HP 1/4  
50  
60  
70  
80  
.65  
.41  
.27  
.77 175.2 7.22 110.5  
.49 160.8 5.52 106.3  
.32 146.4 4.31 102.2  
.84 1.00  
.55  
.37  
.65  
.44  
191.7 6.59 115.2  
177.3 5.22 111.1  
162.9 4.20 106.9  
.71  
.49  
.34  
.84  
.58  
.41  
20 173.1 17.84 10 0.6 4.0 0 4.77 207.4 21.37 108.6 5.07 6.05 241.6 24.90 116.6 6.34 7.56 275.8 28.42 124.6 7.65 9.13  
25  
30  
165.1 13.61 98.7 2.58  
157.0 10.79 96.8 1.78  
3.08 199.3 16.43 106.7  
2.12 191.2 13.14 104.8  
1.12 175.1 9.02 101.0  
.65 159.0 6.56 97.3  
.39 142.9 4.91 93.5  
.24 126.8 3.73 89.7  
3.30 3.93 2335 19.25 114.7 4.16 4.96  
2.30 2.74 225.5 15.49 112.8 2.92 3.48  
1.26 1.50 209.4 10.79 109.1 1.62 1.93  
267.8 22.07 122.7 5.06 6.05  
259.7 17.84 120.9 3.57 4.26  
243.6 12.55 117.1 2.02 2.40  
227.5 9.38 113.3 1.26 1.50  
260-W2  
CFM 3933 40  
RPM 1100 50  
140.9 7.26 93.0  
124.8 5.14 89.2  
108.7 3.73 85.5  
92.6 2.73 81.7  
.94  
.54  
.33  
.20  
.76  
.48  
.31  
.20  
.90 193.3 7.97 105.3  
.57 177.1 6.08 101.5  
.37 161.0 4.74 97.7  
.24 144.9 3.73 94.0  
.99 1.18  
HP 1/2  
60  
70  
80  
.64  
.43  
.30  
.76  
.51  
.35  
211.4 7.26 109.5  
195.3 5.75 105.8  
179.1 4.62 102.0  
.83  
.57  
.40  
.99  
.68  
.48  
110.7 2.85 85.9  
20 223.0 22.98 107.2 7.98 9.51 266.2 27.43 116.4 10.02 11.95 309.4 31.89 125.6 12.45 14.95 352.7 36.34 134.7 14.96 17.84  
25  
30  
213.9 17.63 105.3 5.21  
204.8 14.07 103.4 3.63  
186.6 9.61 99.5 1.98  
168.4 6.94 95.7 1.18  
6.21 257.1 21.20 114.5  
4.33 248.0 17.04 112.5  
2.36 229.8 11.84 108.7  
1.41 211.6 8.72 104.8  
.88 193.4 6.64 101.0  
.56 175.2 5.16 97.1  
6.59 7.86 300.3 24.76 123.6 8.25 9.84  
4.64 5.53 291.2 20.01 121.7 5.84 6.96  
2.60 3.10 273.0 14.07 117.8 3.30 3.94  
1.60 1.91 254.8 10.50 114.0 2.06 2.46  
1.05 1.25 236.6 8.13 110.1 1.36 1.63  
343.6 28.32 132.8 9.97 11.89  
334.5 22.98 130.9 7.10 8.47  
316.3 16.30 127.0 4.07 4.86  
298.1 12.29 123.2 2.58 3.08  
279.9 9.61 119.3 1.74 2.08  
261.7 7.70 115.4 1.22 1.46  
320-W2  
CFM 4350 40  
RPM 1100 50  
HP 1/2  
60  
70  
80  
150.2 5.16 91.8  
132.0 3.89 88.0  
.74  
.47  
.70  
.48  
.84 218.5 6.43 106.3  
.57 200.3 5.16 102.4  
.94 1.12  
.67 .80  
157.0 4.05 93.3  
243.5 6.27 111.6  
.88 1.05  
20 249.7 25.73 101.6 9.61 11.46 298.1 30.72 109.7 12.07 14.40 346.5 35.71 117.8 15.0 0 17.89  
25  
30  
239.5 19.75 99.9 6.28  
229.3 15.76 98.2 4.37  
209.0 10.77 94.8 2.38  
188.6 7.77 91.4 1.42  
7.48 287.9 23.74 108.0  
5.21 277.8 19.08 106.3  
2.84 257.4 13.26 102.9  
1.69 237.0 9.77 99.5  
1.06 216.6 7.44 96.1  
.68 196.2 5.78 92.7  
7.93 9.46 336.4 27.73 116.1 9.94 11.85  
5.59 6.66 326.2 22.41 114.4 7.03 8.38  
3.13 3.73 305.8 15.76 111.0 3.97 4.74  
1.93 2.30 285.4 11.76 107.6 2.48 2.96  
1.26 1.50 265.0 9.10 104.2 1.64 1.96  
.85 1.01 244.6 7.20 100.8 1.13 1.35  
384.8 31.72 124.2 12.01 14.33  
374.6 25.73 122.5 8.55 10.20  
354.2 18.25 119.1 4.90 5.85  
333.8 13.76 115.7 3.11 3.71  
313.4 10.77 112.3 2.10 2.50  
293.1 8.63 108.9 1.47 1.75  
272.7 7.02 105.5 1.06 1.26  
354-W2  
CFM 5528 40  
RPM 1100 50  
HP 1/2  
60  
70  
80  
168.2 5.78 88.0  
147.8 4.35 84.6  
.89  
.57  
175.8 4.53 89.3  
.58  
.69 224.3 5.78 97.4  
.80  
.96  
20 282.5 29.12 102.3 10.88 12.90 340.0 35.05 110.8 14.25 17.23 396.0 40.92 119.2 17.59 21.10 454.0 46.80 127.9 21.25 26.20  
25  
30  
270.0 22.27 100.4 7.10  
260.0 17.87 98.9 4.91  
235.0 12.11 95.1 2.61  
213.0 8.78 91.9 1.56  
190.0 6.53 88.4 1.04  
8.47 324.0 26.72 108.5  
5.84 313.0 21.51 106.8  
3.06 289.0 14.90 103.2  
1.94 266.0 10.97 99.8  
1.31 243.0 8.35 96.3  
.96 221.0 6.51 93.1  
9.53 11.25 382.0 31.51 117.1 12.25 14.62  
6.66 7.97 369.0 25.36 115.2 8.82 10.36  
3.65 4.24 346.0 17.84 111.7 4.88 5.81  
2.21 2.62 323.0 13.32 108.3 3.03 3.51  
1.43 1.82 298.0 10.24 104.6 1.96 2.39  
1.04 1.28 276.0 8.13 101.3 1.37 1.72  
440.0 36.29 125.8 14.95 18.10  
428.0 29.42 124.0 11.05 13.10  
405.0 20.88 120.6 6.32 7.61  
381.0 15.71 117.0 3.97 4.60  
357.0 12.27 113.4 2.65 3.14  
335.0 9.87 110.1 1.87 2.30  
312.0 8.04 106.7 1.35 1.71  
400-W2  
CFM 6017 40  
RPM 1140 50  
HP 3/4  
60  
70  
90  
168.0 4.95 85.1  
.75  
197.0 5.08 89.5  
.77  
.98 252.0 6.49 97.7 1.05 1.30  
UH-PRC001-EN  
29  
Perform ance  
Data  
Table PD-2 (Continued) – Model S Unit Heater Hot Water Capacities – 60°F Ent. AirTemp. Hot Water with Turbulators and 132 Fin Series  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
20  
30  
40  
50  
60  
260 F  
300 F  
340 F  
380 F  
Unit  
Size  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T. MBH GPM  
18.0 1.85 112.6  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
.07  
.02  
.01  
.08  
.03  
.01  
22.9 2.36 127.1  
19.5 1.34 116.9  
.10  
.04  
.02  
.01  
.11  
.04  
.02  
.01  
27.9 2.88 141.7  
24.4 1.68 131.5  
21.0 1.08 121.3  
.13  
.05  
.02  
.01  
.01  
.15  
.06  
.03  
.01  
.01  
.07  
.03  
.02  
.01  
.08  
.04  
.02  
.01  
20-W2  
CFM 315  
RPM 1075  
HP 1/50  
14.5  
11.0  
.99 102.4  
.57 92.2  
29.4 2.02 146.1  
26.0 1.34 135.9  
16.0  
12.5  
.82 106.8  
.52 96.6  
17.5  
14.0  
.72 111.2  
.48 101.0  
22.5  
19.0  
.93 125.7  
.65 115.6  
40  
50  
60  
80  
34.1 1.76 121.1  
29.9 1.23 113.6  
.10  
.06  
.03  
.01  
.12  
.07  
.04  
.01  
44.2 2.28 139.3  
40.1 1.65 131.8  
35.9 1.23 124.3  
.15  
.09  
.05  
.02  
.01  
.18  
.10  
.06  
.03  
.01  
.08  
.03  
.02  
.01  
.09  
.04  
.02  
.01  
38-W2  
25.7  
17.3  
.88 106.1  
.45 91.1  
46.0 1.58 142.5  
CFM 514  
27.5  
19.1  
.71 109.3  
.39 94.3  
37.7  
29.3  
20.9  
.97 127.5  
.60 112.5  
.36 97.5  
47.8 1.23 145.8  
.05  
.02  
.01  
.01  
06  
RPM 1550 100  
HP 1/20  
39.5  
31.1  
22.7  
.81 130.8  
.53 115.7  
.33 100.7  
.03  
.01  
.01  
120  
140  
40  
50  
60  
80  
34.6 1.78 120.2  
30.4 1.25 112.9  
.10  
.06  
.03  
.01  
.12  
.07  
.04  
.01  
45.0 2.32 138.2  
40.7 1.68 130.8  
36.5 1.25 123.4  
.15  
.09  
.06  
.02  
.01  
.18  
.11  
.07  
.03  
.01  
.08  
.04  
.02  
.01  
.09  
.04  
.02  
.01  
42-W2  
26.2  
17.7  
.90 105.5  
.46 90.7  
46.8 1.61 141.4  
CFM 530  
28.0  
19.5  
.72 108.7  
.40 93.9  
38.3  
29.8  
21.4  
.99 126.6  
.61 111.9  
.37 97.1  
48.6 1.25 144.6  
.05  
.03  
.01  
.01  
.06  
.03  
.02  
.01  
RPM 1550 100  
HP 1/20  
40.2  
31.7  
23.2  
.83 129.8  
.54 115.1  
.34 100.3  
120  
140  
40  
50  
60  
80  
56.1 2.89 128.4  
51.2 2.11 122.5  
46.4 1.59 116.6  
.32  
.19  
.12  
.05  
.02  
.01  
.38  
.23  
.14  
.06  
.03  
.01  
71.1 3.67 146.8  
66.3 2.73 140.9  
61.5 2.11 135.0  
51.8 1.33 123.2  
.45  
.28  
.18  
.09  
.04  
.02  
.01  
.54  
.33  
.22  
.10  
.05  
.03  
.01  
60-W2  
CFM 755  
36.7  
27.1  
17.4  
.95 104.8  
.56 93.0  
.30 81.2  
66.9 1.72 141.6  
57.2 1.18 129.8  
47.5  
37.9  
28.2  
.12  
.07  
.04  
.02  
.01  
.15  
.08  
.04  
.02  
.01  
RPM 1550 100  
HP 1/20  
42.1  
32.5  
22.8  
.87 111.4  
.56 99.6  
.34 87.8  
72.3 1.49 148.2  
62.6 1.08 136.4  
.09  
.05  
.03  
.02  
.11  
.07  
.04  
.02  
120  
140  
160  
.82 118.0  
.56 106.2  
.36 94.4  
52.9  
43.3  
.78 124.6  
.56 112.8  
40  
50  
60  
64.4 3.32 119.2  
59.0 2.43 114.2  
53.6 1.84 109.2  
42.7 1.10 99.2  
.40  
.24  
.15  
.07  
.03  
.01  
.48  
.29  
.18  
.08  
.03  
.01  
81.7 4.21 135.0  
76.3 3.14 130.0  
70.8 2.43 125.0  
59.9 1.54 115.0  
49.0 1.01 105.0  
.57  
.35  
.23  
.11  
.06  
.03  
.01  
.67  
.42  
.27  
.13  
07  
.03  
.01  
.46  
.31  
.16  
.09  
.05  
.03  
.01  
.55  
.37  
.19  
.10  
.06  
.03  
.02  
93.5 3.85 145.8  
88.1 3.02 140.8  
77.2 1.99 130.8  
66.3 1.37 120.8  
70-W2  
CFM 1004 80  
RPM 1550 100  
94.4 2.43 146.7  
83.5 1.72 136.7  
72.6 1.25 126.7  
61.7  
50.8  
.20  
.12  
.07  
.04  
.02  
.24  
.14  
.08  
.05  
.03  
31.8  
20.9  
.65 89.2  
.36 79.2  
HP 1/8  
120  
140  
160  
38.1  
27.2  
.65 95.0  
.40 85.0  
55.4  
44.5  
33.6  
.95 110.8  
.65 100.8  
.43 90.8  
.91 116.7  
.65 106.7  
50  
60  
82.0 3.38 125.0  
76.1 2.62 120.4  
64.4 1.66 111.1  
52.7 1.09 101.8  
.55  
.37  
.17  
.09  
.04  
.02  
.01  
.66 104.3 4.30 142.7  
.77  
.52  
.27  
.15  
.08  
.05  
.03  
.01  
.92  
.63  
.44  
.21  
.11  
.05  
.02  
.01  
98.4 3.38 138.0  
86.7 2.23 128.7  
74.9 1.54 119.4  
63.2 1.09 110.1  
80  
.32 108.9 2.81 146.4  
.37  
.21  
.13  
.08  
.05  
.03  
.44  
.25  
.15  
.10  
.06  
.03  
90-W2  
100  
.18  
.10  
.06  
.03  
.01  
97.2 2.00 137.1  
85.5 1.47 127.8  
73.7 1.09 118.5  
62.0  
50.3  
CFM 1162 120  
RPM 1550 140  
40.9  
29.2  
17.5  
.70 92.5  
.43 83.2  
.23 73.9  
107.7 1.85 145.4  
96.0 1.41 136.1  
84.3 1.09 126.8  
.18  
.12  
.08  
.05  
.21  
.14  
.09  
.06  
51.5  
39.7  
28.0  
.76 100.8  
.51 91.5  
.32 82.2  
HP 1/8  
160  
180  
.80 109.2  
.58 99.9  
72.5  
.83 117.5  
40  
50  
60  
80  
96.9 4.99 122.6 1.05  
1.25 121.5 6.26 138.5  
.78 114.9 4.74 134.2  
.51 108.4 3.72 130.0  
1.43 1.71  
.91 1.09  
90.3 3.72 118.3  
83.8 2.88 114.1  
70.7 1.82 105.6  
57.6 1.19 97.2  
.65  
.43  
.20  
.10  
.05  
.02  
.01  
.62  
.31  
.17  
.10  
.05  
.03  
.01  
.73 133.0 4.57 145.9  
.37 119.9 3.09 137.4  
.21 106.8 2.20 129.0  
.12  
.06  
.03  
.02  
.81  
.43  
.25  
.15  
.09  
.06  
.03  
.96  
.51  
.30  
.18  
.11  
.07  
.04  
100-W2  
.24  
.12  
.06  
.03  
.01  
95.3 2.45 121.5  
82.2 1.69 113.1  
69.1 1.19 104.6  
CFM 1427 100  
RPM 1550 120  
131.4 2.71 144.9  
118.3 2.03 136.4  
105.2 1.55 128.0  
92.1 1.19 119.5  
.33  
.21  
.13  
.09  
.06  
.39  
.25  
.16  
.11  
.07  
44.5  
31.4  
18.3  
.76 88.7  
.46 80.3  
.24 71.8  
93.7 1.61 120.5  
80.6 1.19 112.1  
67.5  
54.4  
HP 1/8  
140  
160  
180  
56.0  
42.9  
29.8  
.82 96.2  
.55 87.7  
.34 79.3  
.87 103.6  
.62 95.2  
79.0  
.91 111.1  
60  
80  
115.3 3.96 124.0  
100.4 2.59 115.7  
85.5 1.76 107.4  
70.6 1.21 99.2  
.97  
.49  
.26  
.14  
.08  
.04  
.02  
1.16 147.3 5.06 141.7  
.58 132.4 3.41 133.5  
.31 117.5 2.42 125.2  
.17 102.6 1.76 116.9  
1.36 1.62  
.72  
.42  
.25  
.15  
.09  
.05  
.86 164.4 4.24 151.2  
.50 149.5 3.08 143.0  
.30 134.6 2.31 134.7  
.18 119.7 1.76 126.4  
.11 104.8 1.35 118.2  
.97 1.15  
126-W2  
100  
.58  
.37  
.24  
.16  
.10  
.69  
.44  
.29  
.19  
.12  
CFM 1661 120  
RPM 1100 140  
55.7  
40.8  
25.9  
.82 90.9  
.53 82.6  
.30 74.4  
.09  
.05  
.02  
87.7 1.29 108.7  
151.7 2.23 144.2  
136.8 1.76 135.9  
121.9 1.40 127.6  
.33  
.23  
.16  
.39  
.27  
.19  
HP 1/6  
160  
180  
72.8  
57.9  
.94 100.4  
.66 92.1  
.06  
89.9 1.03 109.9  
30  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-2 (Continued) – Model S Unit Heater Hot Water Capacities – 60°F Ent. AirTemp. Hot Water with Turbulators and 132 Fin Series  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
60  
80  
260 F  
300 F  
340 F  
380 F  
MBH GPM  
Unit  
Size  
PD  
FT S.W.T. H.W.T. MBH GPM  
156.9 5.39 123.8 1.98 2.36 199.2 6.84 141.0  
138.8 3.57 116.4 1.02  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
FT S.W.T. H.W.T.  
2.75 3.28  
1.49 1.77  
168-W2  
1.22 181.0 4.66 133.6  
.68 162.9 3.36 126.2  
.39 144.7 2.49 118.8  
.23 126.6 1.86 111.5  
.13 108.5 1.40 104.1  
CFM 2267 100  
RPM 1100 120  
120.6 2.49 109.9  
102.5 1.76 101.7  
84.3 1.24 94.3  
.57  
.33  
.19  
.11  
.05  
.88 1.05 205.2 4.23 143.4 1.20 1.43  
.55  
.35  
.22  
.14  
.65 187.0 3.21 136.0  
.41 168.9 2.49 128.7  
.26 150.7 1.94 121.3  
.16 132.6 1.52 113.9  
.78  
.52  
.35  
.24  
.93  
.62  
.42  
.28  
HP 1/6  
140  
160  
180  
211.1 3.11 145.8  
193.0 2.49 138.5  
174.9 2.00 131.1  
.70  
.49  
.35  
.83  
.59  
.42  
66.2  
48.1  
.85 86.9  
.55 79.5  
.06  
90.3 1.03 96.7  
50  
60  
80  
179.7 7.41 121.6 3.31  
169.8 5.83 118.2 2.25  
150.2 3.87 111.5 1.17  
3.95 225.4 9.29 137.2  
2.69 215.6 7.41 133.9  
1.39 195.9 5.05 127.1  
.78 176.3 3.63 120.4  
.45 156.7 2.69 113.7  
.26 137.0 2.02 106.9  
.14 117.4 1.51 100.2  
4.51 5.38  
3.13 3.73  
186-W2  
1.69 2.02 241.7 6.23 142.8 2.24 2.67  
1.00 1.20 222.1 4.58 136.1 1.37 1.63  
CFM 2690 100  
RPM 1100 120  
130.6 2.69 104.7  
110.9 1.90 98.0  
91.3 1.34 91.3  
.65  
.38  
.21  
.12  
.06  
.62  
.39  
.25  
.15  
.74 202.4 3.48 129.4  
.47 182.8 2.69 122.6  
.30 163.1 2.10 115.9  
.18 143.5 1.64 109.2  
.89 1.06  
248.2 4.26 145.0 1.16 1.38  
HP 1/4  
140  
160  
180  
.59  
.40  
.27  
.71  
.48  
.32  
228.5 3.36 138.3  
208.9 2.69 131.6  
189.2 2.17 124.8  
.80  
.56  
.40  
.95  
.67  
.48  
71.6  
52.0  
.92 84.5  
.60 77.8  
.07  
97.7 1.12 93.5  
60  
80  
222.6 7.65 124.1  
193.8 4.99 115.8  
165.1 3.40 107.5  
136.3 2.34 99.3  
107.5 1.58 91.0  
78.8 1.01 82.7  
.88  
.44  
.24  
.13  
.07  
.03  
.01  
1.05 284.4 9.77 141.9  
.53 255.6 6.59 133.6  
.28 226.9 4.68 125.3  
.16 198.1 3.40 117.1  
.08 169.3 2.49 108.0  
.04 140.6 1.81 100.5  
.02 111.8 1.28 92.2  
1.23 1.47  
.53  
.33  
.22  
.14  
.09  
.63  
.40  
.26  
.17  
.11  
.65  
.38  
.23  
.14  
.08  
.05  
.78  
230-W2  
100  
.45 288.6 5.95 143.1  
.27 259.9 4.46 134.8  
.17 231.1 3.40 126.6  
.10 202.3 2.61 118.3  
.06 173.6 1.99 110.0  
CFM 3200 120  
RPM 1100 140  
292.9 4.31 144.4  
264.1 3.40 136.1  
235.4 2.69 127.8  
.30  
.21  
.14  
.36  
.25  
.17  
HP 1/4  
160  
180  
50.0  
.57 74.4  
50  
60  
80  
261.7 10.79 121.3 1.54  
245.6 8.44 117.6 1.03  
1.83 330.2 13.61 137.4  
1.23 314.0 10.79 133.6  
.62 281.8 7.26 126.0  
.33 249.6 5.14 118.5  
.18 217.4 3.73 110.9  
.10 185.2 2.73 103.4  
.05 152.9 1.97 95.8  
.02 120.7 1.38 88.3  
2.11 2.52  
1.45 1.73  
260-W2  
213.4 5.50 110.0  
181.2 3.73 102.5  
148.9 2.56 94.9  
116.7 1.72 87.3  
84.5 1.09 79.8  
.52  
.28  
.15  
.08  
.04  
.02  
.77  
.44  
.27  
.16  
.10  
.05  
.92 350.3 9.02 142.1 1.03 1.23  
CFM 3933 100  
RPM 1100 120  
.53 318.1 6.56 134.5  
.32 285.8 4.91 127.0  
.19 253.6 3.73 119.4  
.11 221.4 2.85 111.9  
.06 189.2 2.17 104.3  
.62  
.39  
.25  
.17  
.11  
.74  
.47  
.30  
.20  
.13  
354.3 6.08 143.0  
322.1 4.74 135.5  
289.8 3.73 127.9  
257.6 2.95 120.4  
.52  
.35  
.24  
.17  
.62  
.42  
.29  
.20  
HP 1/2  
140  
160  
180  
52.3  
.60 72.2  
60  
80  
323.1 11.10 128.5 2.14  
286.7 7.39 120.7 1.11  
2.55  
1.33 373.2 9.61 139.1  
.75 336.8 6.94 131.4  
.44 300.4 5.16 123.0  
.25 264.0 3.89 115.9  
.14 227.6 2,93 108.2  
.08 191.2 2.19 100.5  
1.61 1.92  
.96 1.14  
320-W2  
100  
250.3 5.16 113.0  
213.9 3.67 105.3  
177.5 2.61 97.6  
141.1 1.82 89.9  
104.8 1.20 82.2  
.63  
.37  
.21  
.12  
.06  
CFM 4350 120  
RPM 1100 140  
.60  
.38  
.25  
.15  
.71 386.8 6.64 142.0  
.46 350.4 5.16 134.3  
.29 314.1 4.05 126.5  
.18 277.7 3.18 118.8  
.85 1.01  
.54  
.39  
.64  
.46  
.57  
.39  
.27  
.68  
HP 1/2  
160  
180  
.46 400.5 5.16 144.9  
.32  
364.1 4.17 137.1  
50  
60  
80  
382.2 15.76 123.7 3.76  
361.8 12.43 120.3 2.57  
321.1 8.27 113.5 1.34  
4.49 479.1 19.75 139.9  
3.07 458.7 15.76 136.5  
1.60 417.9 10.77 129.7  
.90 377.1 7.77 122.9  
.53 336.4 5.78 116.1  
.31 295.6 4.35 109.3  
.17 254.9 3.28 102.5  
.09 214.1 2.45 95.7  
5.10 6.08  
3.55 4.24  
354-W2  
1.93 2.31 514.7 13.26 145.8 2.54 3.03  
1.15 1.38 474.0 9.77 139.0 1.57 1.87  
CFM 5528 100  
RPM 1100 120  
280.3 5.78 106.7  
239.6 4.11 99.9  
198.8 2.93 93.1  
158.0 2.04 86.3  
117.3 1.34 79.6  
.76  
.44  
.26  
.15  
.08  
.72  
.46  
.30  
.19  
.86 433.2 7.44 132.2 1.02 1.22  
HP 1/2  
140  
160  
180  
.55 392.4 5.78 125.4  
.35 351.7 4.53 118.6  
.22 310.9 3.56 111.8  
.69  
.47  
.32  
.82  
.56  
.38  
489.3 7.20 141.6  
448.5 5.78 134.8  
407.7 4.67 128.0  
.92 1.09  
.65  
.47  
.78  
.56  
50  
60  
80  
440.0 18.14 125.8 5.00  
417.0 14.33 122.4 3.41  
372.0 9.59 115.6 1.78  
326.0 6.72 108.8 1.08  
5.92 559.0 23.05 143.5  
3.95 535.0 18.38 140.0  
2.18 489.0 12.60 133.1  
1.33 443.0 9.13 126.3  
.92 397.0 6.82 119.4  
.71 351.0 5.17 112.5  
.52 305.0 3.93 105.6  
.43 259.0 2.97 98.7  
7.55 8.97  
5.13 6.16  
400-W2  
2.79 3.26 620.0 15.98 152.7 4.09 4.77  
1.62 2.03 590.0 11.96 146.7 2.58 3.03  
1.10 1.37 540.0 9.28 140.8 1.69 2.04  
.78 1.00 501.0 7.38 134.9 1.22 1.53  
CFM 6017 100  
RPM 1140 120  
280.0 4.81 101.9  
234.0 3.45 95.0  
188.0 2.42 88.1  
143.0 1.64 81.4  
.70  
.51  
.35  
.23  
HP 3/4  
140  
160  
180  
612.0 9.01 151.5 1.60 2.00  
568.0 7.37 144.9 1.20 1.52  
527.0 6.04 138.8  
.57  
.42  
.78 461.0 5.94 128.9  
.62 422.0 4.83 123.1  
.91 1.21  
.71 .92  
.96 1.14  
UH-PRC001-EN  
31  
Perform ance  
Data  
Table PD-3 – Model P Unit Heater Hot Water Capacities – 60°F Ent. AirTemp.  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
10  
15  
20  
180 F  
200 F  
220 F  
240 F  
Unit  
Size  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T. MBH GPM  
23.8 4.90 96.9  
20.8 2.86 92.2  
17.8 1.83 87.5  
14.8 1.22 82.9  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
.26  
.09  
.04  
.02  
.34  
.12  
28.8 5.93 104.6  
25.7 3.54 99.9  
.37  
.14  
.06  
.03  
.02  
.49  
.18  
.08  
.04  
.02  
33.7 6.95 112.2  
30.7 4.22 107.6  
27.7 2.86 102.9  
24.7 2.04 98.3  
21.7 1.49 93.6  
.49  
.19  
.09  
.05  
.03  
.65  
.25  
.12  
.06  
.03  
38.7 7.98 119.9  
35.7 4.90 115.3  
32.7 3.37 110.6  
29.7 2.45 105.9  
26.7 1.83 101.3  
20.6 1.06 91.9  
.64  
.25  
.12  
.07  
.04  
.01  
.84  
.33  
.16  
.09  
.05  
.02  
42-P  
CFM 595  
.05 22.7 2.34 95.2  
RPM 1550 25  
.02  
19.7 1.63 90.6  
16.7 1.15 85.9  
HP 1/40  
30  
40  
10  
15  
20  
18.9 3.90 100.0  
16.6 2.27 95.0  
14.2 1.46 90.0  
.17  
.06  
.03  
.22  
.08  
22.9 4.71 108.3  
20.5 2.82 103.3  
.24  
.09  
.04  
.02  
.01  
.31  
.12  
26.8 5.52 116.6  
24.4 3.36 111.6  
.32  
.12  
.06  
.03  
.02  
.42  
.16  
.08  
.04  
.02  
30.7 6.33 125.0  
28.4 3.90 120.0  
26.0 2.68 115.0  
23.7 1.95 110.0  
21.3 1.46 105.0  
.41  
.16  
.08  
.04  
.02  
.01  
.54  
.21  
.10  
.06  
.03  
.01  
42-P  
CFM 436  
.03 18.1 1.87 98.3  
.05 22.1 2.27 106.7  
RPM 1150 25  
HP 1/40  
15.8 1.30 93.3  
.03  
.01  
19.7 1.63 101.7  
17.4 1.19 96.7  
30  
40  
13.4  
.92 88.4  
16.6  
.85 95.0  
10  
15  
20  
25  
40.0 8.25 97.3  
35.8 4.91 93.3  
31.5 3.25 89.4  
27.3 2.25 85.4  
23.0 1.58 81.4  
.75  
.28  
.13  
.06  
.03  
1.00  
.37  
48.1 9.92 104.8  
43.9 6.03 100.9  
1.05 1.40  
56.2 11.58 112.4 1.40 1.86  
64.3 13.25 119.9 1.80 2.39  
.41  
.19  
.10  
.06  
.02  
.54  
.26  
.14  
.08  
.02  
51.9 7.14 108.4  
47.7 4.19 104.4  
43.4 3.58 100.5  
39.2 2.69 96.5  
30.7 1.58 88.6  
.56  
.27  
.15  
.09  
.03  
.01  
.74  
.36  
.20  
.12  
.04  
.02  
60.0 8.25 115.9  
55.8 5.75 112.0  
51.5 4.25 108.0  
47.3 3.25 104.0  
38.8 2.00 96.1  
30.2 1.25 88.2  
.73  
.36  
.21  
.12  
.05  
.02  
.97  
.49  
.27  
.16  
.07  
.03  
64-P  
.17 39.6 4.08 96.9  
CFM 989  
.08  
.04  
35.3 2.91 92.9  
31.1 2.14 89.0  
22.6 1.16 81.0  
RPM 1550 30  
HP 1/20  
40  
50  
22.2  
.91 80.7  
10  
15  
20  
25  
31.7 6.53 101.4  
28.4 3.90 97.1  
25.1 2.58 92.7  
21.8 1.79 88.4  
18.5 1.27 84.1  
.48  
.18  
.08  
.04  
.02  
.64  
.24  
38.1 7.85 109.7  
34.8 4.78 105.4  
.67  
.26  
.13  
.07  
.04  
.90  
.35  
.17  
.09  
.05  
44.5 9.17 118.1  
41.2 5.66 113.7  
37.8 3.90 109.4  
34.5 2.85 105.1  
31.2 2.15 100.8  
24.6 1.27 92.1  
.90 1.19  
50.9 10.48 126.4 1.15 1.53  
.36  
.18  
.10  
.06  
.02  
.48  
.23  
.13  
.08  
.03  
47.5 6.53 122.1  
44.2 4.56 117.7  
40.9 3.37 113.4  
37.6 2.58 109.1  
31.0 1.60 100.5  
24.4 1.00 91.8  
.47  
.23  
.13  
.08  
.03  
.01  
.62  
.31  
.18  
.11  
.04  
.02  
64-P  
.11 31.5 3.24 101.1  
CFM 706  
.06  
.03  
28.2 2.32 96.7  
24.8 1.71 92.4  
RPM 1150 30  
HP 1/20  
40  
50  
10  
15  
20  
48.9 10.07 97.5  
43.7 6.01 93.6  
38.6 3.97 89.6  
33.4 2.75 85.7  
28.2 1.94 81.7  
.70  
.26  
.12  
.06  
.03  
.90  
.34  
58.7 12.11 105.1  
53.6 7.36 101.2  
.98 1.27  
68.6 14.14 112.7 1.31 1.69  
78.5 16.17 120.3 1.68 2.16  
.38  
.18  
.10  
.05  
.02  
.49  
.23 58.3 6.01 104.8  
63.5 8.72 108.7  
.52  
.25  
.14  
.08  
.03  
.67  
.33  
.18  
.10  
.04  
73.3 10.07 116.3  
68.2 7.02 112.3  
63.0 5.19 108.4  
57.8 3.97 104.4  
47.5 2.45 96.5  
37.2 1.53 88.6  
.68  
.34  
.19  
.11  
.05  
.02  
.87  
.44  
.25  
.15  
.06  
.02  
80-P  
.15 48.4 4.99 97.2  
CFM 1200 25  
RPM 1550 30  
.08  
.04  
43.3 3.57 93.2  
38.1 2.62 89.3  
27.8 1.43 81.3  
.12  
.07  
.02  
53.1 4.38 100.8  
48.0 3.30 96.8  
37.7 1.94 88.9  
HP 1/20  
40  
50  
10  
15  
20  
25  
38.7 7.99 101.6  
34.7 4.77 97.3  
30.7 3.16 93.0  
26.7 2.20 88.7  
22.7 1.56 84.4  
.45  
.17  
.08  
.04  
.02  
.58  
.22  
46.5 9.59 110.0  
42.5 5.84 105.7  
.63  
.24  
.12  
.06  
.03  
.81  
.31  
54.3 11.20 118.4  
50.3 6.91 114.1  
.84 1.08  
62.1 12.81 126.7 1.07 1.38  
.33  
.16  
.09  
.05  
.02  
.43  
.21  
.12  
.07  
.03  
58.1 7.99 122.4  
54.1 5.57 118.1  
50.1 4.13 113.8  
46.1 3.16 109.5  
38.0 1.96 100.9  
30.0 1.24 92.2  
.43  
.22  
.12  
.07  
.03  
.01  
.56  
.28  
.16  
.10  
.04  
.02  
80-P  
.10 38.5 3.97 101.4  
.15 46.3 4.77 109.7  
CFM 858  
.05  
.03  
34.5 2.84 97.0  
30.5 2.09 92.7  
.08  
.04  
42.3 3.49 105.4  
38.3 2.63 101.1  
30.2 1.56 92.5  
RPM 1150 30  
HP 1/20  
40  
50  
See Table SP-12 for abbreviations.  
32  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-3 (Continued) – Model P Unit Heater Hot Water Capacities – 60°F Ent.AirTemp.  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
10  
15  
20  
180 F  
200 F  
220 F  
240 F  
Unit  
Size  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T. MBH GPM  
64.9 13.38 99.1 1.50  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
101.8 20.98 121.4 3.40 4.42  
97.3 13.38 118.7 1.45 1.88  
92.9 9.57 116.0  
88.4 7.29 113.3  
83.9 5.77 110.6  
75.0 3.86 105.2  
66.1 2.72 99.9  
57.1 1.96 94.5  
FT S.W.T. H.W.T.  
1.96  
.80  
77.2 15.91 106.6  
72.7 9.99 103.9  
.40 68.3 7.03 101.2  
2.06 2.68  
.85 1.11  
89.5 18.45 114.0 2.69 3.50  
85.0 11.68 111.3 1.13 1.48  
60.4 8.30 96.4  
56.0 5.77 93.8  
51.5 4.24 91.1  
47.0 3.23 88.4  
38.1 1.96 83.0  
.61  
.31  
.17  
.10  
.04  
102-P  
.44  
.25  
.16  
.07  
.03  
.58 80.6 8.30 108.6  
.59  
.35  
.22  
.10  
.05  
.03  
.78  
.46  
.29  
.13  
.07  
.03  
.77 1.0 0  
CFM 1528 25  
RPM 1070 30  
.23  
.14  
.05  
63.8 5.26 98.5  
59.3 4.08 95.8  
50.4 2.60 90.4  
41.5 1.71 85.0  
.33  
.21  
.09  
.04  
76.1 6.27 105.9  
71.6 4.92 103.2  
62.7 3.23 97.8  
53.8 2.22 92.4  
44.8 1.54 87.0  
.46  
.30  
.14  
.07  
.04  
.60  
.39  
.18  
.09  
.05  
HP 1/8  
40  
50  
60  
10  
15  
20  
53.6 11.04 100.9 1.04  
1.36  
.56  
63.7 13.13 108.6  
60.1 8.26 105.8  
1.43 1.86  
73.8 15.22 116.3 1.87 2.43  
70.2 9.65 113.6 .79 1.03  
.40 66.6 6.86 110.8  
84.0 17.31 124.1 2.36 3.07  
80.4 11.04 121.3 1.01 1.31  
50.0 6.86 98.1  
46.3 4.77 95.4  
42.7 3.52 92.6  
39.1 2.69 89.8  
31.9 1.64 84.3  
.43  
.22  
.12  
.07  
.03  
.59  
.31  
.18  
.11  
.78  
102-P  
.28 56.5 5.82 103.1  
.41  
.24  
.16  
.07  
.04  
.02  
.54  
.32  
.20  
.09  
.05  
.02  
76.7 7.91 118.6  
73.1 6.03 115.8  
69.5 4.77 113.0  
62.3 3.21 107.5  
55.0 2.27 102.0  
47.8 1.64 96.5  
.53  
.32  
.21  
.10  
.05  
.03  
.70  
.42  
.27  
.13  
.07  
.04  
CFM 1208 25  
.16  
.10  
.04  
52.9 4.36 100.3  
49.2 3.38 97.6  
42.0 2.16 92.0  
34.8 1.43 86.5  
.23  
.15  
.06  
.03  
63.0 5.19 108.1  
59.4 4.08 105.3  
52.1 2.69 99.8  
44.9 1.85 94.2  
37.6 1.29 88.7  
RPM 850  
HP 1/8  
30  
40  
50  
60  
.05  
.02  
10  
15  
20  
79.7 16.43 101.1 2.22  
2.89  
1.17  
94.9 19.55 108.9  
89.3 12.27 106.0  
3.04 3.96 110.0 22.68 116.7 3.99 5.18  
1.26 1.64 104.4 14.35 113.8 1.67 2.18  
125.2 25.80 124.5 5.04 6.55  
119.6 16.43 121.6 2.14 2.78  
74.1 10.19 98.2  
68.6 7.06 95.3  
63.0 5.19 92.4  
57.4 3.94 89.5  
46.2 2.38 83.8  
.90  
.45  
.25  
.15  
.06  
122-P  
.59 83.7 8.63 103.1  
.65  
.37  
.23  
.10  
.04  
.02  
.85 98.9 10.19 110.9  
.87 1.14 114.0 11.75 118.7 1.13 1.48  
CFM 1790 25  
RPM 1100 30  
.33  
.20  
.08  
78.1 6.44 100.2  
72.5 4.98 97.3  
61.4 3.16 91.6  
50.2 2.07 85.8  
39.0 1.34 80.1  
.49  
.30  
.13  
.06  
.03  
93.3 7.69 108.0  
87.7 6.02 105.1  
76.5 3.94 9.94  
65.3 2.69 93.6  
54.2 1.86 87.9  
.51  
.32  
.15  
07  
.67  
.42  
.19  
.09  
.05  
108.4 8.94 115.8  
102.8 7.06 112.9  
91.7 4.72 107.2  
80.5 3.32 101.4  
69.3 2.38 95.7  
.68  
.43  
.20  
.10  
.06  
.88  
.57  
.27  
.14  
.07  
HP 1/6  
40  
50  
60  
.04  
10  
15  
20  
99.0 20.41 101.1 3.18  
92.8 12.76 98.5 1.32  
4.27 117.6 24.24 108.8  
1.77 111.4 15.31 106.3  
.91 105.2 10.84 103.7  
4.32 5.81 136.2 28.07 116.5 5.61 7.54  
1.83 2.45 130.0 17.86 114.0 2.40 3.23  
154.8 31.89 124.2 7.05 9.47  
148.6 20.41 121.7 3.04 4.09  
146-P  
86.7 8.93 96.0  
80.5 6.63 93.4  
74.3 5.10 90.8  
61.9 3.19 85.7  
49.5 2.04 80.6  
.68  
.39  
.24  
.10  
.04  
.96 1.29 123.8 12.76 111.4 1.28 1.72 142.4 14.67 119.1 1.64 2.20  
CFM 2220 25  
RPM 1100 30  
.52  
.32  
.14  
.06  
99.0 8.16 101.1  
92.8 6.38 98.5  
80.5 4.15 93.4  
68.1 2.81 88.3  
55.7 1.91 83.1  
.56  
.36  
.16  
.08  
.04  
.76 117.6 9.70 108.8  
.48 111.4 7.65 106.3  
.77 1.03  
136.2 11.23 116.5  
130.0 8.93 114.0  
117.6 6.06 108.8  
105.2 4.34 103.7  
92.8 3.19 98.5  
.99 1.33  
.49  
.23  
.12  
.06  
.66  
.31  
.16  
.09  
.65  
.31  
.17  
.10  
.87  
.42  
.23  
.13  
HP 1/6  
40  
50  
60  
.22  
.10  
.05  
99.0 5.10 101.1  
86.6 3.57 96.0  
74.3 2.55 90.8  
10  
15  
20  
111.5 22.98 99.2 2.70  
104.6 14.38 96.8 1.12  
3.59 132.4 27.29 106.6  
1.49 125.5 17.24 104.1  
.77 118.6 12.22 101.7  
.44 111.7 9.21 99.3  
.27 104.8 7.20 96.9  
3.67 4.88 153.3 31.59 113.9 4.77 6.34  
1.55 2.06 146.4 20.11 111.5 2.04 2.71  
174.2 35.89 121.3 6.00 7.96  
167.3 22.98 118.8 2.59 3.44  
166-P  
97.7 10.07 94.4  
90.8 7.49 92.0  
84.0 5.77 89.5  
70.2 3.62 84.7  
56.4 2.32 79.8  
.58  
.33  
.20  
.09  
.04  
.81 1.08 139.5 14.38 109.1 1.09 1.45 160.4 16.53 116.4 1.39 1.95  
CFM 2620 25  
RPM 1100 30  
.48  
30  
.64 132.6 10.93 106.6  
.40 125.7 8.64 104.2  
.18 111.9 5.77 99.4  
.65  
.42  
.20  
.10  
.06  
.87  
.56  
.26  
.14  
.07  
153.5 12.65 114.0  
146.6 10.07 111.6  
132.8 6.84 106.7  
119.0 4.91 101.9  
105.3 3.62 97.0  
.85 1.12  
.55  
.27  
.14  
.08  
.79  
.36  
.19  
.11  
HP 1/6  
40  
50  
60  
.11  
.05  
91.1 4.69 92.0  
77.3 3.19 87.2  
63.5 2.18 82.3  
.14  
.07  
.03  
.09  
.04  
98.2 4.05 94.5  
84.4 2.90 89.7  
See Table SP-12 for abbreviations.  
UH-PRC001-EN  
33  
Perform ance  
Data  
Table PD-3 (Continued) – Model P Unit Heater Hot Water Capacities – 60°F Ent. AirTemp.  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
260 F  
300 F  
340 F  
380 F  
Unit  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
Size  
Drop °F MBH GPM  
FT S.W.T. H.W.T. MBH GPM  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
42-P  
50  
60  
19.6  
.81 90.3  
.01  
.01  
29.5 1.22 105.7  
.02  
.01  
.02  
.01  
39.4 1.63 121.1  
33.4 1.15 111.8  
.03  
.02  
.04  
.02  
49.4 2.04 136.5  
43.4 1.49 127.2  
.04  
.02  
.01  
.06  
.03  
.01  
CFM 595  
RPM 1550 80  
HP 1/40  
23.5  
.81 96.4  
31.3  
.81 108.5  
42-P  
CFM 436  
50  
23.7  
.98 110.0  
.01  
.02  
31.5 1.30 126.7  
26.8 .92 116.7  
.02  
.01  
.03  
.01  
39.4 1.63 143.4  
34.7 1.19 133.4  
.03  
.02  
.04  
.02  
RPM 1150 60  
HP 1/40  
64-P  
50  
60  
38.3 1.58 95.7  
29.8 1.02 87.8  
.03  
.01  
.04  
.02  
54.5 2.25 110.8  
46.0 1.58 102.9  
.06  
.03  
.01  
.08  
.04  
.01  
70.7 2.91 125.9  
62.2 2.14 117.9  
45.2 1.16 102.1  
.10  
.05  
.02  
.13  
.07  
.02  
86.9 3.58 141.0  
78.4 2.69 133.0  
61.3 1.58 117.2  
.14  
.08  
.03  
.01  
.19  
.11  
.04  
.01  
CFM 989  
RPM 1550 80  
HP 1/20  
29.0  
.75 87.0  
100  
44.3  
.91 101.3  
64-P  
50  
60  
30.8 1.27 100.1  
.02  
.01  
.03  
.01  
43.5 1.79 116.8  
36.9 1.27 108.2  
.04  
.02  
.05  
.03  
56.3 2.32 133.5  
49.7 1.71 124.9  
.06  
.03  
.01  
.08  
.05  
.02  
69.1 2.85 150.2  
62.5 2.15 141.5  
49.2 1.27 124.2  
.09  
.05  
.02  
.01  
.12  
.07  
.03  
.01  
CFM 706  
24.1  
.83 91.5  
RPM 1150 80  
HP 1/20  
36.4  
.94 107.6  
100  
36.0  
.74 106.9  
80-P  
50  
47.1 1.94 96.2  
36.8 1.26 88.2  
.03  
.01  
.04  
.02  
66.8 2.75 111.3  
56.5 1.94 103.4  
.06  
.03  
.07  
.04  
86.5 3.57 126.5  
76.2 2.62 118.5  
55.6 1.43 102.7  
.09  
.05  
.02  
.12  
.06  
106.3 4.38 141.6  
96.0 3.30 133.7  
75.3 1.94 .117.9  
.13  
.08  
.03  
.01  
.17  
.10  
.04  
CFM 1200 60  
RPM 1550 80  
.02  
100  
54.7  
1.13 102.0  
.01  
80-P  
50  
60  
37.8 1.56 100.6  
29.8 1.02 92.0  
.02  
.01  
.02  
.01  
53.4 2.20 117.3  
45.3 1.56 108.7  
.04  
.02  
.05  
.02  
69.0 2.84 134.1  
60.9 2.09 125.5  
44.9 1.16 108.2  
.06  
.03  
.01  
.08  
.04  
.01  
84.6 3.49 150.8  
76.5 2.63 142.2  
60.5 1.56 125.0  
.08  
.05  
.02  
.11  
.06  
.02  
CFM 858  
RPM 1150 80  
HP 1/20  
50  
78.4 3.23 107.3  
69.4 2.39 101.9  
51.6 1.33 91.1  
.10  
.06  
.02  
.13 103.0 4.24 122.1  
.16  
.10  
.04  
.02  
.21 127.6 5.26 137.0  
.13 118.7 4.08 131.6  
.05 100.8 2.60 120.8  
.24  
.15  
.06  
.03  
.01  
.31  
.19  
.08  
.04  
.02  
152.2 6.27 151.8  
143.3 4.92 146.4  
125.4 3.23 135.6  
107.5 2.22 124.9  
89.6 1.54 114.1  
71.8 1.06 103.3  
.33  
.21  
.09  
.05  
.02  
.01  
.42  
.27  
.12  
.06  
.03  
.02  
102-P  
60  
.07  
.02  
94.0 3.23 116.7  
76.2 1.96 105.9  
58.3 1.20 95.2  
CFM 1528 80  
RPM 1070 100  
.02  
82.9 1.71 110.0  
65.0 1.12 99.2  
HP 1/8  
120  
140  
50  
60  
65.2 2.69 109.7  
57.9 1.99 104.2  
43.4 1.12 93.1  
.07  
.04  
.01  
.09  
.05  
.02  
85.4 3.52 125.2  
78.2 2.69 119.7  
63.7 1.64 108.6  
49.2 1.01 97.6  
.11  
.07  
.03  
.01  
.15 105.7 4.36 140.6  
.17  
.10  
.04  
.02  
.01  
.22  
.13  
.06  
.03  
.01  
126.0 5.19 156.1  
118.7 4.08 150.6  
104.3 2.69 139.5  
89.8 1.85 128.5  
75.3 1.29 117.4  
.23  
.14  
.07  
.03  
.02  
.30  
.19  
.09  
.04  
.02  
102-P  
.09  
.04  
.01  
98.5 3.38 135.1  
84.0 2.16 124.1  
69.5 1.43 113.0  
CFM 1208 80  
RPM 850 100  
HP 1/8  
120  
55.0  
.95 102.0  
50  
60  
95.6 3.94 109.2  
84.5 2.90 103.5  
62.1 1.60 92.0  
.14  
.08  
.03  
.19 125.9 5.19 124.8  
.11 114.8 3.94 119.1  
.24  
.14  
.05  
.02  
.31 156.2 6.44 140.4  
.18 145.1 4.98 134.7  
.07 122.7 3.16 123.2  
.03 100.4 2.07 111.7  
.35  
.21  
.09  
.04  
.02  
.45  
.28  
.12  
.05  
.02  
186.5 7.69 156.0  
175.4 6.02 150.3  
163.0 3.94 138.8  
130.7 2.69 127.3  
108.3 1.86 115.8  
86.0 1.27 104.3  
.48  
.30  
.14  
.07  
.03  
.02  
.62  
.39  
.18  
.09  
.04  
.02  
122-P  
CFM 1790 80  
RPM 1100 100  
.03  
92.4 2.38 107.6  
70.1 1.44 96.1  
HP 1/6  
120  
140  
78.0 1.34 100.2  
50  
60  
80  
123.8 5.10 111.4  
111.4 3.83 106.2  
86.6 2.23 96.0  
61.9 1.28 85.7  
.23  
.13  
.05  
.02  
.30 160.9 6.63 126.8  
.18 148.5 5.10 121.7  
.07 123.8 3.19 111.4  
.36  
.22  
.09  
.04  
.02  
.48 198.1 8.16 142.2  
.30 185.7 6.38 137.1  
.12 160.9 4.15 126.8  
.05 136.1 2.91 116.5  
.02 111.4 1.91 106.2  
.52  
.33  
.15  
.07  
.04  
.02  
.70  
.44  
.20  
.10  
.05  
.02  
235.2 9.70 157.7  
222.8 7.65 152.5  
198.1 5.10 142.2  
173.3 3.57 131.9  
148.5 2.55 121.7  
123.8 1.82 111.4  
99.0 1.28 101.1  
.70  
.45  
.21  
.11  
.06  
03  
.94  
.61  
.29  
.15  
.08  
.04  
.02  
146-P  
CFM 2220 100  
RPM 1100 120  
.02  
99.0 2.04 101.1  
74.2 1.28 90.8  
HP 1/6  
140  
160  
86.6 1.28 96.0  
.02  
50  
60  
80  
139.9 5.77 109.2  
126.2 4.33 104.4  
98.6 2.54 94.7  
.19  
.11  
.04  
.26 181.7 7.49 123.9  
.15 167.9 5.77 119.1  
.06 140.4 3.62 109.4  
.31  
.19  
.08  
.03  
.01  
.41 223.5 9.21 138.6  
.25 209.7 7.20 133.8  
.11 182.1 4.69 124.1  
.05 154.6 3.19 114.4  
.02 127.0 2.18 104.7  
.44  
.28  
.13  
.06  
.03  
.01  
.59  
.37  
.17  
.08  
.04  
.02  
265.2 10.93 153.3  
251.4 8.64 148.4  
223.9 5.77 138.8  
196.3 4.05 129.1  
168.8 2.90 119.4  
141.2 2.08 109.7  
113.7 1.46 100.0  
.60  
.39  
.18  
.09  
.05  
.03  
.01  
.80  
.51  
.24  
.12  
.07  
.04  
.02  
166-P  
CFM 2620 100  
RPM 1100 120  
112.8 2.32 99.7  
85.3 1.46 90.0  
HP 1/6  
140  
160  
99.5 1.46 95.0  
34  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-4 – Model P Unit Heater Hot Water Capacities – 60°F Ent. AirTemp.  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
180 F  
200 F  
220 F  
240 F  
Unit  
Size  
PD  
PD  
PD  
FT S.W.T. H.W.T MBH GPM  
5.02 6.66  
2.12 2.81 172.7 23.72 109.7 2.79 3.70  
1.11 1.47 164.4 16.94 107.4 1.48 1.97 189.1 19.49 114.5 1.90 2.52  
PD  
PD  
PD  
PD  
PD  
Drop °F MBH GPM  
FT S.W.T. H.W.T. MBH GPM  
131.6 27.11 97.9 3.69  
123.3 16.94 95.5 1.53  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
10  
15  
4.90 156.2 32.20 105.0  
2.03 148.0 20.33 102.6  
197.3 27.11 116.8 3.54 4.70  
202-P  
20 115.1 11.86 93.1  
.78 1.04 139.7 14.40 10 0.2  
CFM 3200 25  
RPM 1100 30  
106.8 8.80 90.8  
98.5 6.77 88.4  
82.0 4.23 83.6  
65.5 2.70 78.9  
.45  
.28  
.11  
.05  
.60 131.5 10.84 97.9  
.37 123.2 8.47 95.5  
.15 106.7 5.50 90.7  
.65  
.41  
.18  
.09  
.04  
.87 156.2 12.87 105.0  
.55 147.9 10.16 102.6  
.25 131.4 6.77 97.8  
.12 114.9 4.74 93.1  
.89 1.18  
180.8 14.91 112.1 1.15 1.53  
.57  
.27  
.14  
.07  
.76  
.36  
.18  
.10  
172.6 11.86 109.7  
156.1 8.04 105.0  
139.6 5.75 100.2  
123.1 4.23 95.4  
.75 1.00  
HP 1/4  
40  
50  
60  
.36  
.19  
.11  
.48  
.26  
.15  
.07  
90.2 3.72 86.0  
73.7 2.53 81.2  
.06  
98.4 3.38 88.3  
10  
15  
166.9 34.40 97.0 6.75  
158.1 21.73 95.0 2.86  
8.98  
3.82 188.9 25.95 101.8  
3.92 5.22 219.6 30.17 108.6 5.12 6.80  
250.3 34.40 115.4 6.45 8.57  
252-P  
20 149.4 15.40 93.1 1.51 2.01 180.1 18.56 99.9 2.10 2.80 210.9 21.73 106.7 2.77 3.69 241.6 24.90 113.5 3.52 4.69  
CFM 4162 25  
RPM 1100 30  
140.7 11.60 91.2  
131.9 9.06 89.2  
114.5 5.90 85.3  
97.0 4.00 81.5  
79.5 2.73 77.6  
.89  
.57  
.26  
.12  
.06  
1.19 171.4 14.13 98.0  
.75 162.7 11.18 96.0  
.34 145.2 7.48 92.2  
.17 127.7 5.26 88.3  
.08 110.2 3.79 84.4  
1.26 1.68 202.1 16.66 104.8 1.69 2.25  
.82 1.09 193.4 13.29 102.8 1.11 1.48  
.39  
.20  
.11  
232.9 19.20 111.6 2.17 2.89  
224.1 15.40 109.6 1.44 1.92  
206.6 10.65 105.8  
189.2 7.80 101.9  
171.7 5.90 98.0  
HP 1/4  
40  
50  
60  
.52 175.9 9.06 99.0  
.27 158.4 6.53 95.1  
.15 141.0 4.84 91.2  
.55  
.30  
.17  
.73  
.40  
.23  
.73  
.41  
.24  
.97  
.54  
.32  
15  
180.4 24.78 97.5 3.66  
4.88 215.4 29.60 104.8  
5.02 6.67 250.5 34.42 112.1 6.55 8.71  
20 170.3 17.55 95.4 1.93 2.57 205.4 21.17 102.7 2.68 3.57 240.5 24.78 110.0 3.54 4.72 275.6 28.40 117.3 4.51 6.0 0  
280-P  
25  
160.2 13.21 93.3 1.14  
1.52 195.3 16.10 100.6  
.96 185.3 12.73 98.5  
.43 165.1 8.51 94.4  
.21 145.0 5.98 90.2  
.10 124.9 4.29 86.0  
1.61 2.15 230.4 19.00 107.9 2.16 2.88  
1.04 1.39 220.4 15.14 105.8 1.42 1.89  
265.5 21.89 115.2 2.77 3.69  
255.4 17.55 113.1 1.84 2.45  
235.3 12.12 109.0  
215.2 8.87 104.8  
195.1 6.70 100.6  
CFM 4430 30  
RPM 1100 40  
150.2 10.32 91.2  
130.1 6.70 87.1  
109.9 4.53 82.9  
89.8 3.08 78.7  
.72  
.32  
.16  
.08  
.49  
.26  
.14  
.66 200.2 10.32 101.7  
.34 180.1 7.42 97.5  
.19 160.0 5.50 93.3  
.70  
.38  
.22  
.93  
.50  
.29  
.92 1.23  
.52  
.31  
HP 1/2  
50  
60  
.69  
.41  
15  
213.4 29.32 97.7 5.02  
6.68 254.9 35.03 105.1  
6.88 9.14  
20 201.3 20.75 95.6 2.63 3.51 242.9 25.03 103.0 3.67 4.89 284.5 29.32 110.3 4.86 6.46 326.0 33.60 117.7 6.18 8.22  
336-P  
25  
189.3 15.61 93.5 1.55  
2.07 230.9 19.04 100.8  
1.31 218.9 15.04 98.7  
.59 194.9 10.04 94.5  
.28 170.8 7.04 90.2  
.14 146.8 5.04 86.0  
2.21 2.94 272.5 22.46 108.2 2.95 3.93  
1.42 1.90 260.5 17.89 106.1 1.93 2.58  
314.0 25.89 115.6 3.80 5.05  
302.0 20.75 113.4 2.51 3.35  
278.0 14.32 109.2 1.26 1.68  
254.0 10.47 104.9  
229.9 7.90 100.7  
CFM 5210 30  
RPM 1140 40  
177.3 12.18 91.4  
153.3 7.90 87.1  
129.3 5.33 82.9  
105.2 3.61 78.6  
.98  
.44  
.21  
.10  
.67  
.35  
.19  
.90 236.4 12.18 101.8  
.47 212.4 8.76 97.6  
.25 188.4 6.47 93.3  
.95 1.26  
.51  
.29  
HP 3/4  
50  
60  
.69  
.39  
.71  
.42  
.94  
.56  
15  
246.7 33.89 97.0 4.81  
6.46 294.7 40.49 104.2  
6.60 8.86  
20 232.8 23.99 94.9 2.52 3.39 280.3 28.94 102.2 3.52 4.73 328.9 33.89 109.4 4.66 6.26 376.9 38.84 116.6 5.94 7.97  
384-P  
25  
218.9 18.05 92.9 1.48  
2.00 267.0 22.01 100.1  
1.26 253.1 17.39 98.0  
.57 225.4 11.61 93.8  
.27 197.7 8.15 89.7  
.13 170.0 5.84 85.5  
2.11 2.84 315.0 25.97 107.3 2.83 3.80  
1.36 1.83 301.2 20.69 105.2 1.85 2.49  
363.1 29.93 114.5 3.65 4.89  
349.2 23.99 112.4 2.41 3.24  
321.5 16.56 108.3 1.21 1.62  
293.8 12.11 104.1  
266.0 9.14 99.9  
CFM 6140 30  
RPM 1140 40  
205.1 14.09 90.8  
177.4 9.14 86.6  
149.6 6.17 82.5  
121.9 4.19 78.3  
.94  
.42  
.20  
.10  
.64  
.33  
.18  
.87 273.4 14.09 101.0  
.45 245.7 10.13 96.9  
.24 218.0 7.49 92.7  
.91 1.22  
.49  
.28  
HP 3/4  
50  
60  
.66  
.38  
.67  
.40  
.91  
.54  
20 305.7 31.50 95.1 4.19 5.71 368.1 37.93 102.3 5.81 7.91  
500-P  
25  
288.4 23.78 93.1 2.49  
271.1 18.63 91.2 1.59  
3.39 350.8 28.92 100.3  
2.16 333.6 22.92 98.3  
.99 299.1 15.41 94.4  
.49 264.6 10.90 90.4  
.25 230.0 7.90 86.4  
3.52 4.79 413.3 34.07 107.5 4.69 6.38  
2.29 3.11 396.0 27.21 105.5 3.09 4.20  
1.10 1.49 361.5 18.63 101.5 1.53 2.09  
475.7 39.22 114.7 6.00 8.17  
458.5 31.50 112.7 3.99 5.43  
424.0 21.84 108.7 2.03 2.76  
389.4 16.05 104.8 1.15 1.56  
CFM 8020 30  
RPM 1160 40  
236.6 12.19 87.2  
202.1 8.33 83.2  
167.6 5.76 79.3  
.73  
.36  
.18  
HP 1-1/2  
50  
60  
.58  
.32  
.79 327.0 13.48 97.6  
.44 292.5 10.05 93.6  
.84 1.15  
.49  
.67  
354.9 12.19 100.8  
.69  
.94  
15  
378.1 51.96 96.9 6.43  
8.40 451.2 62.00 104.0  
8.78 11.46  
20 358.1 36.90 94.9 3.41 4.45 431.1 44.43 102.0 4.72 6.17 504.2 51.96 109.2 6.22 8.12  
600-P  
25  
338.0 27.86 93.0 2.02  
317.9 21.84 91.0 1.29  
2.65 411.1 33.89 100.1  
1.69 391.0 26.86 98.1  
.78 350.8 18.08 94.2  
.39 310.7 12.81 90.3  
.20 270.5 9.29 86.4  
2.86 3.73 484.1 39.91 107.2 3.81 4.97  
1.86 2.43 464.0 31.88 105.3 2.51 3.28  
.89 1.17 423.9 21.84 101.3 1.25 1.63  
557.2 45.93 114.3 4.88 6.36  
537.1 36.90 112.4 3.24 4.24  
496.9 25.61 108.5 1.65 2.15  
456.8 18.83 104.6  
416.6 14.31 100.6  
CFM 9450 30  
RPM 1160 40  
277.8 14.31 87.1  
237.6 9.79 83.2  
197.4 6.78 79.3  
.59  
.29  
.15  
HP 1-1/2  
50  
60  
.47  
.26  
.62 383.7 15.82 97.4  
.34 343.6 11.80 93.5  
.69  
.40  
.90  
.53  
.93 1.22  
.56  
.74  
15  
455.6 62.60 98.2 7.21  
9.88  
20 431.3 44.45 96.1 3.82 5.22 519.4 53.52 103.5 5.29 7.25 607.5 62.60 110.9 6.97 9.56  
720-P  
25  
407.1 33.56 94.1 2.27  
382.8 26.30 92.1 1.45  
3.10 495.1 40.82 101.5  
1.97 470.9 32.35 99.5  
.90 422.3 21.76 95.4  
.45 373.7 15.41 91.3  
.23 325.2 11.17 87.2  
3.20 4.38 583.2 48.08 108.9 4.27 5.85  
2.08 2.84 558.9 38.40 106.8 2.81 3.85  
1.00 1.36 510.4 26.30 102.8 1.40 1.91  
.53  
.29  
671.3 55.34 116.2 5.46 7.49  
647.0 44.45 114.2 3.63 4.98  
598.4 30.83 110.1 1.85 2.52  
549.9 22.67 106.1 1.05 1.43  
CFM 11,000 30  
RPM 1165 40  
334.2 17.22 88.0  
285.7 11.78 83.9  
237.1 8.15 79.9  
.66  
.33  
.17  
HP 3  
50  
60  
.72 461.8 19.04 98.7  
.40 413.3 14.20 94.6  
.77 1.05  
.45 .61  
501.3 17.22 102.0  
.63  
.86  
See Table SP-12 for abbreviations.  
UH-PRC001-EN  
35  
Perform ance  
Data  
Table PD-4 (Continued) – Model P Unit Heater Hot Water Capacities – 60°F Ent. AirTemp.  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
50  
60  
80  
260 F  
300 F  
340 F  
380 F  
Unit  
Size  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T.  
.82 1.08  
PD  
FT S.W.T. H.W.T. MBH GPM  
164.2 6.77 107.3  
147.7 5.07 102.6  
114.7 2.96 93.0  
FT S.W.T. H.W.T MBH GPM  
.35 213.6 8.80 121.5  
FT S.W.T. H.W.T  
.55 263.0 10.84 135.7  
MBH GPM  
.26  
.15  
.06  
.42  
.25  
.11  
.05  
.02  
.60  
.38  
.17  
.08  
.04  
.02  
.80  
.50  
.23  
.11  
.05  
.03  
312.3 12.87 150.0  
295.8 10.16 145.2  
262.8 6.77 135.7  
229.8 4.74 126.2  
196.8 3.38 116.7  
163.8 2.41 107.2  
130.7 1.68 97.7  
.20 197.1 6.77 116.8  
.07 164.1 4.23 107.3  
.34 246.4 8.47 131.0  
.14 213.4 5.50 121.5  
.06 180.4 3.72 112.0  
.03 147.4 2.53 102.5  
.52  
.25  
.13  
.07  
.04  
.02  
.70  
.33  
.17  
.09  
.05  
.02  
202-P  
CFM 3200 100  
RPM 1100 120  
131.1 2.70 97.8  
98.1 1.68 88.2  
HP 1/4  
140  
160  
114.4 1.68 92.9  
50  
60  
80  
219.9 9.06 108.7  
202.4 6.95 104.8  
167.5 4.31 97.1  
132.5 2.73 89.3  
.53  
.33  
.13  
.06  
.71 281.4 11.60 122.3  
.43 263.9 9.06 118.4  
.18 228.9 5.90 110.7  
.08 194.0 4.00 103.0  
.82 1.09 342.8 14.13 135.9 1.16 1.54  
404.3 16.66 149.5 1.55 2.06  
386.8 13.29 145.7 1.01 1.35  
.52  
.23  
.11  
.06  
.03  
.69 325.3 11.18 132.0  
.31 290.4 7.48 124.3  
.15 255.4 5.26 116.6  
.08 220.5 3.79 108.8  
.04 185.5 2.73 101.1  
- 150.6 1.94 93.3  
.75 1.00  
252-P  
.36  
.19  
.10  
.06  
.03  
.47  
.25  
.14  
.07  
.04  
351.8 9.06 137.9  
316.9 6.53 130.2  
281.9 4.84 122.4  
247.0 3.64 114.7  
212.0 2.73 107.0  
177.1 2.03 99.2  
142.2 1.46 91.5  
.50  
.27  
.16  
.09  
.05  
.03  
.02  
.66  
.36  
.21  
.12  
.07  
.04  
.02  
CFM 4162 100  
RPM 1100 120  
159.0 2.73 95.2  
124.1 1.83 87.5  
HP 1/4  
140  
160  
180  
200  
50  
60  
250.3 10.32 112.1  
230.2 7.91 107.9  
189.9 4.89 99.5  
149.7 3.08 91.1  
109.4 1.88 82.8  
.68  
.41  
.17  
.07  
.03  
.90 320.5 13.21 126.7  
.55 300.3 10.32 122.5  
.23 260.1 6.70 114.1  
.10 219.9 4.53 105.7  
.04 179.6 3.08 97.4  
1.04 1.39 390.6 16.10 141.3 1.48 1.97  
460.8 19.00 155.9 1.98 2.63  
440.7 15.14 151.7 1.30 1.72  
.66  
.30  
.14  
.07  
.03  
.88 370.5 12.73 137.1  
.40 330.3 8.51 128.7  
.19 290.0 5.98 120.3  
.10 249.8 4.29 112.0  
.05 209.5 3.08 103.6  
.95 1.27  
80  
.45  
.24  
.13  
.07  
.04  
.60 400.5 10.32 143.3  
.63  
34  
.85  
.46  
.26  
.16  
.09  
.05  
.03  
280-P  
100  
.31  
.17  
.09  
.05  
360.2 7.42 134.9  
320.0 5.50 126.6  
279.7 4.12 118.2  
239.5 3.08 109.8  
199.2 2.28 101.5  
159.0 1.64 93.1  
CFM 4430 120  
RPM 1100 140  
20  
139.4 2.05 89.0  
.12  
07  
HP 1/2  
160  
180  
200  
169.3 2.18 95.2  
.04  
.02  
50  
60  
295.5 12.18 112.3  
271.5 9.33 108.0  
223.4 5.76 99.5  
175.4 3.61 91.0  
127.3 2.19 82.5  
.92  
.56  
.23  
.10  
.04  
1.23 378.7 15.61 127.0  
.75 354.6 12.18 122.7  
.31 306.6 7.90 114.2  
.13 258.5 5.33 105.7  
.05 210.5 3.61 97.2  
1.43 1.90 461.8 19.04 141.7 2.02 2.69  
.90 1.20 437.8 15.04 137.4 1.30 1.74  
544.9 22.46 156.4 2.71 3.60  
520.9 17.89 152.1 1.77 2.36  
80  
.40  
.20  
.10  
.04  
.54 389.7 10.04 128.9  
.26 341.7 7.04 120.4  
.13 293.6 5.04 111.9  
.06 245.6 3.61 103.4  
.62  
.32  
.17  
.09  
.05  
.02  
.82  
.43  
.23  
.12  
.07  
.03  
472.9 12.18 143.6  
424.8 8.76 135.1  
376.7 6.47 126.6  
328.7 4.84 118.1  
280.6 3.61 109.6  
232.6 2.66 101.1  
104.5 1.90 92.6  
.87 1.15  
336-P  
100  
.47  
.27  
.16  
.09  
.05  
.03  
.63  
.36  
.21  
.12  
.07  
.04  
CFM 5210 120  
RPM 1140 140  
162.4 2.39 88.7  
HP 3/4  
160  
180  
200  
197.5 2.54 94.9  
149.4 1.71 86.4  
36  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-4 (Continued) – Model P Unit Heater Hot Water Capacities – 60°F Ent.AirTemp.  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
260 F  
300 F  
340 F  
380 F  
Unit  
Size  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
Drop °F MBH GPM  
FT S.W.T. H.W.T. MBH GPM  
341.8 14.09 111.3  
314.1 10.79 107.1  
258.6 6.66 98.8  
203.2 4.19 90.5  
147.8 2.54 82.2  
FT S.W.T. H.W.T MBH GPM  
1.19 437.9 18.05 125.7  
FT S.W.T. H.W.T  
1.37 1.84 534.0 22.01 140.2 1.94 2.61  
.86 1.16 506.2 17.39 136.0 1.25 1.68  
MBH GPM  
630.0 25.97 154.6 2.61 3.50  
602.3 20.69 150.4 1.70 2.28  
546.9 14.09 142.1  
491.4 10.13 133.8  
436.0 7.49 125.4  
380.6 5.60 117.1  
325.1 4.19 108.8  
269.7 3.09 100.5  
214.3 2.21 92.2  
FT S.W.T. H.W.T.  
50  
60  
.88  
.54  
.22  
.09  
.04  
.72 410.2 14.09 121.6  
.30 354.7 9.14 113.2  
.13 299.3 6.17 104.9  
.05 243.8 4.19 96.6  
80  
.39  
.19  
.09  
.04  
.52 450.8 11.61 127.7  
.25 395.4 8.15 119.3  
.12 339.9 5.84 111.0  
.06 284.5 4.19 102.7  
.59  
.31  
.17  
.09  
.05  
.02  
.79  
.41  
.22  
.12  
.06  
.03  
.83 1.12  
384-P  
100  
.45  
.26  
.15  
.09  
.05  
.03  
.60  
.35  
.20  
.10  
.07  
.04  
CFM 6140 120  
RPM 1140 140  
188.4 2.77 88.3  
HP 3/4  
160  
180  
200  
229.1 2.95 94.4  
173.6 1.99 86.1  
50  
60  
451.9 18.63 111.9 1.49  
2.03 576.8 23.78 126.3  
1.25 542.3 18.63 122.3  
.53 473.2 12.19 114.4  
.23 404.2 8.33 106.5  
.10 335.2 5.76 98.5  
2.28 3.11 701.7 28.92 140.6 3.21 4.37  
1.45 1.98 667.2 22.92 136.7 2.09 2.84  
826.6 34.07 155.0 4.28 5.82  
792.1 27.21 151.0 2.81 3.83  
723.0 18.63 143.1 1.39 1.90  
417.4 14.34 108.0  
348.3 8.97 100.0  
279.3 5.76 92.1  
210.3 3.61 84.2  
.92  
.39  
.17  
.07  
80  
.66  
33  
.90 598.1 15.41 128.7 1.00 1.36  
500-P  
100  
.45 529.1 10.90 120.8  
.23 460.1 7.90 112.9  
.11 391.0 5.76 104.9  
.05 322.0 4.15 97.0  
.53  
.29  
.16  
.09  
.05  
.72  
.40  
.22  
.12  
.06  
654.0 13.48 135.2  
585.0 10.05 127.2  
515.9 7.60 119.3  
446.9 5.76 111.4  
377.9 4.33 103.4  
308.8 3.18 95.5  
.77 1.04  
CFM 8020 120  
RPM 1160 140  
.17  
.08  
.04  
.45  
.27  
.16  
.10  
.05  
.61  
.36  
.22  
.13  
.07  
266.1 3.92 90.6  
197.1 2.54 82.7  
HP 1-1/2  
160  
180  
200  
253.0 2.90 89.1  
50  
60  
529.9 21.84 111.7 1.21  
1.58 676.0 27.86 125.9  
.98 635.8 21.84 122.0  
.41 555.5 14.31 114.2  
.18 475.2 9.79 106.3  
.08 394.9 6.78 98.5  
1.86 2.42 822.1 33.89 140.2 2.61 3.41  
1.18 1.54 781.9 26.86 136.3 1.70 2.22  
968.2 39.91 154.4 3.48 4.54  
928.1 31.88 150.5 2.29 2.99  
847.8 21.84 142.7 1.14 1.48  
489.7 16.82 107.8  
409.4 10.55 99.9  
329.1 6.78 92.1  
248.8 4.27 84.3  
.75  
.32  
.14  
.06  
80  
.54  
.27  
.14  
.07  
.03  
.71 701.6 18.08 182.4  
.35 621.3 12.81 120.6  
.18 541.0 9.29 112.8  
.09 460.7 6.78 104.9  
.04 380.4 4.90 97.1  
.82 1.07  
600-P  
100  
.43  
.24  
.13  
.07  
.04  
.56  
.31  
.18  
.10  
.05  
767.5 15.82 134.8  
687.1 11.80 127.0  
606.8 8.93 119.2  
526.5 6.78 111.4  
446.2 5.11 103.5  
365.9 3.77 95.7  
.63  
.36  
.22  
.13  
.08  
.04  
.82  
.48  
.29  
.17  
.10  
.06  
CFM 9450 120  
RPM 1160 140  
314.6 4.63 90.7  
234.3 3.02 82.8  
HP 1-1/2  
160  
180  
200  
300.1 3.44 89.3  
50  
60  
638.0 26.30 113.5 1.36  
1.85 814.1 33.56 128.2  
1.14 765.6 26.20 124.1  
.48 668.5 17.22 116.0  
.21 571.4 11.78 107.9  
.09 474.2 8.15 99.7  
2.08 2.85 990.3 40.82 143.0 2.93 4.02 1166.4 48.08 157.7 3.89 5.36  
1.32 1.81 941.7 32.35 138.9 1.90 2.61 1117.8 38.40 153.7 2.56 3.52  
589.4 20.25 109.4  
492.3 12.68 101.2  
395.2 8.15 93.1  
298.1 5.12 85.0  
.84  
.35  
.16  
.07  
80  
.61  
.30  
.15  
.08  
.03  
.83 844.6 21.76 130.8  
.41 747.5 15.41 122.6  
.21 650.4 11.17 114.5  
.10 553.3 8.15 106.4  
.05 456.2 5.88 98.2  
.91 1.25 1020.7 26.30 145.5 1.27 1.74  
720-P  
100  
.48  
.27  
.15  
.08  
.04  
.66  
.36  
.20  
.11  
.06  
923.6 19.04 137.4  
826.5 14.20 129.3  
729.4 10.74 121.1  
632.3 8.15 113.0  
535.2 6.13 104.8  
438.1 4.51 96.7  
.70  
.41  
.24  
.15  
.09  
.05  
.96  
.56  
.33  
.20  
.12  
.07  
CFM 11,000 120  
RPM 1165 140  
377.1 5.55 91.6  
280.0 3.61 83.5  
HP 3  
160  
180  
200  
359.1 4.11 90.1  
UH-PRC001-EN  
37  
Perform ance  
Data  
Table PD-5 – Model P-L Unit Heater Hot Water Capacities – 60°F Ent. AirTemp. (Capacities shown are for units with all Air Ports open)  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
10  
15  
20  
180 F  
200 F  
220 F  
240 F  
Unit  
Size  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T. MBH GPM  
19.7 4.07 87.2  
17.3 2.37 83.8  
14.8 1.53 80.4  
12.3 1.02 77.0  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
.18  
.06  
.03  
.01  
.24  
.09  
23.9 4.92 92.9  
21.4 2.94 89.5  
.26  
.10  
.04  
.02  
.01  
.34  
.13  
28.0 5.77 98.61  
25.5 3.50 95.2  
.34  
.13  
.06  
.03  
.02  
.46  
.18  
.08  
.04  
.02  
-  
32.1 6.61 104.3  
29.6 4.07 100.9  
27.1 2.80 97.5  
24.7 2.03 94.0  
22.2 1.53 90.6  
.44  
.18  
.09  
.05  
.03  
.01  
.59  
.23  
.11  
.06  
.04  
.01  
42-P-L  
CFM 668  
.04 18.9 1.95 86.1  
.06 23.0 2.37 91.8  
RPM 1550 25  
.02  
16.4 1.36 82.7  
.03  
.02  
20.6 1.69 88.4  
18.1 1.24 85.0  
HP 1/40  
30  
40  
14.0  
.96 79.3  
17.3  
.89 83.8  
10  
15  
20  
13.9 2.86 87.2  
12.2 1.68 84.0  
10.6 1.09 80.8  
.09  
.03  
.01  
.12  
.04  
16.7 3.45 92.8  
15.1 2.08 89.6  
.13  
.05  
.02  
.01  
.17  
.07  
19.6 4.04 98.4  
18.0 2.47 95.2  
.17  
.07  
.03  
.02  
.01  
.23  
.09  
.04  
.02  
.01  
22.5 4.63 104.1  
20.8 2.86 100.8  
19.2 1.98 97.6  
17.6 1.45 94.4  
15.9 1.09 91.2  
.22  
.09  
.04  
.02  
.01  
.30  
.12  
.06  
.03  
.02  
42-P-L  
CFM 470  
.02 13.5 1.39 86.4  
.03 16.3 1.68 92.0  
RPM 1150 25  
HP 1/40  
11.8  
.98 83.2  
.02  
14.7 1.21 88.8  
13.1 .90 85.6  
30  
10  
15  
20  
34.6 7.12 86.5  
30.9 4.25 83.7  
27.3 2.81 81.0  
23.6 1.95 78.2  
20.0 1.37 75.4  
.57  
.21  
.10  
.05  
.03  
.76  
.28  
41.5 8.56 91.9  
37.9 5.21 89.1  
.80 1.06  
48.5 10.00 97.2 1.06 1.41  
55.5 11.43 102.6 1.36 1.80  
.31  
.15  
.08  
.04  
.01  
.41  
44.9 6.16 94.5  
.42  
.21  
.11  
.56  
.28  
.15  
.09  
.03  
51.8 7.12 99.8  
48.2 4.97 97.0  
44.6 3.67 94.2  
40.9 2.81 91.4  
33.6 1.73 85.8  
26.4 1.09 80.2  
.55  
.28  
.16  
09  
.04  
.02  
.73  
.37  
.21  
.12  
.05  
.02  
64-P-L  
.13 34.2 3.53 86.3  
.20 41.2 4.25 91.7  
CFM 1200 25  
RPM 1550 30  
.06  
.03  
30.6 2.52 83.5  
27.0 1.85 80.7  
19.7 1.01 75.1  
.10  
.06  
.02  
37.6 3.10 88.9  
33.9 2.33 86.1  
26.7 1.37 80.5  
.07  
.02  
HP 1/20  
40  
50  
10  
15  
20  
25  
27.0 5.56 88.9  
24.2 3.33 85.9  
21.4 2.21 82.9  
18.7 1.54 80.0  
15.9 1.09 77.0  
.35  
.13  
.06  
.03  
.02  
.47  
.18  
32.4 6.68 94.7  
29.6 4.07 91.7  
.50  
.19  
.09  
.05  
.03  
.66  
.26  
37.8 7.80 100.4  
35.1 4.82 97.5  
.66  
.26  
.13  
.07  
.04  
.02  
.88  
.35  
.17  
.10  
.06  
.02  
43.3 8.91 106.2  
40.5 5.56 103.3  
37.7 3.89 10 0.3  
34.9 2.88 97.3  
32.2 2.21 94.4  
26.6 1.37 88.4  
.84 1.12  
.34  
.17  
.10  
.06  
.02  
.01  
.46  
.23  
.13  
.08  
.03  
.01  
64-P-L  
.08 26.9 2.77 88.7  
.12 32.3 3.33 94.5  
CFM 862  
.04  
.02  
24.1 1.99 85.8  
21.3 1.46 82.8  
.07  
.04  
29.5 2.43 91.5  
26.7 1.84 88.6  
21.2 1.09 82.6  
RPM 1150 30  
HP 1/20  
40  
50  
21.1  
.87 82.5  
10  
15  
20  
40.7 8.40 87.6  
36.5 5.02 84.7  
32.3 3.33 81.9  
28.1 2.31 79.0  
23.8 1.64 76.1  
.49  
.18  
.08  
.04  
.02  
.64  
.24  
48.9 10.09 93.2  
44.7 6.14 90.3  
.69  
.27  
.13  
.07  
.04  
.89  
.35  
57.1 11.78 98.7  
52.9 7.27 95.9  
.92 1.19  
65.4 13.47 104.3 1.18 1.52  
.37  
.18  
.10  
.06  
.02  
.47  
.23  
.13  
.07  
.03  
61.1 8.40 101.4  
56.9 5.86 98.6  
52.7 4.34 95.7  
48.4 3.33 92.8  
40.0 2.06 87.1  
31.5 1.30 81.3  
.48  
.24  
.14  
.08  
.03  
.01  
.62  
.31  
.18  
.11  
.04  
.02  
8O-P-L  
.11 40.5 4.17 87.4  
.17 48.7 5.02 93.0  
CFM 1360 25  
RPM 1550 30  
.05  
.03  
36.3 2.99 84.6  
32.0 2.20 81.7  
.09  
.05  
44.5 3.66 90.1  
40.2 2.76 87.3  
31.8 1.64 81.5  
HP 1/20  
40  
50  
10  
15  
20  
32.1 6.61 89.7  
28.8 3.96 86.7  
25.5 2.63 83.6  
22.2 1.83 80.6  
.31  
.12  
.05  
.03  
.40  
.15  
38.5 7.94 95.7  
35.2 4.84 92.6  
.44  
.17  
.08  
.04  
.02  
.56  
.22  
44.9 9.26 101.6  
41.7 5.73 98.6  
.58  
.23  
.11  
.06  
.04  
.01  
.75  
.30  
.15  
.08  
.05  
.02  
51.4 10.59 107.6  
48.1 6.61 104.6  
44.8 4.62 101.5  
41.6 3.43 98.5  
38.3 2.63 95.5  
31.7 1.63 89.4  
.74  
.30  
.15  
09  
.05  
.02  
.96  
.39  
.20  
.11  
.07  
.03  
80-P-L  
CFM 995  
.07 32.0 3.29 89.6  
.11 38.4 3.96 95.6  
RPM 1150 25  
HP 1/20  
.04  
28.7 2.36 86.6  
25.4 1.75 83.5  
.06  
.03  
35.1 2.89 92.5  
31.8 2.19 89.5  
25.3 1.30 83.4  
30  
40  
See Table SP-12 for abbreviations.  
38  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-5 (Continued) – Model P-L Unit Heater Hot Water Capacities – 60°F Ent.AirTemp. (Capacities shown are for units with all Air Ports open)  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
10  
15  
20  
180 F  
200 F  
220 F  
240 F  
Unit  
Size  
PD  
PD  
PD  
FT S.W.T. H.W.T MBH GPM  
63.7 13.13 93.5 1.43 1.86 73.8 15.22 98.8 1.87 2.43  
60.1 8.26 91.6 70.2 9.65 96.9 .79 1.03  
.40 66.6 6.86 95.0  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T. MBH GPM  
53.6 11.04 88.2 1.04  
FT S.W.T. H.W.T  
MBH GPM  
84.0 17.31 104.2 2.36 3.07  
80.4 11.04 102.3 1.01 1.31  
76.7 7.91 10 0.4  
73.1 6.03 98.5  
69.5 4.77 96.6  
62.3 3.21 92.8  
55.0 2.27 88.9  
47.8 1.64 85.1  
FT S.W.T. H.W.T.  
1.36  
.56  
50.0 6.86 86.3  
46.3 4.77 84.4  
42.7 3.52 82.5  
39.1 2.69 80.6  
31.9 1.64 76.8  
.43  
.22  
.12  
.07  
.03  
.59  
.31  
.18  
.11  
.05  
.02  
.78  
102-P-L  
.23 56.5 5.82 89.7  
.41  
.24  
.16  
.07  
.04  
.02  
.54  
.32  
.20  
.09  
.05  
.02  
.53  
.32  
.21  
.10  
.05  
.03  
.70  
.42  
.27  
.13  
.07  
.04  
CFM 1752 25  
RPM 1070 30  
.16  
.10  
.04  
52.9 4.36 87.8  
49.2 3.38 85.9  
42.0 2.16 82.1  
34.8 1.43 78.3  
.23  
.15  
.06  
.03  
63.0 5.19 93.1  
59.4 4.08 91.2  
52.1 2.69 87.4  
44.9 1.85 83.6  
37.6 1.29 79.8  
HP 1/8  
40  
50  
60  
10  
15  
20  
45.9 9.45 88.2  
42.8 5.89 86.3  
39.8 4.10 84.5  
36.8 3.03 82.6  
33.8 2.32 80.8  
.78  
.32  
.16  
.09  
.06  
1.02  
.42  
54.5 11.24 93.5  
51.5 7.07 91.7  
1.06 1.39  
63.2 13.02 98.8 1.39 1.81  
71.8 14.80 104.2 1.75 2.28  
.44  
.23  
.13  
.08  
.04  
.58  
.30  
.18  
.11  
.05  
60.1 8.26 97.0  
57.1 5.89 95.1  
54.1 4.46 93.3  
51.1 3.51 91.4  
45.0 2.32 87.7  
39.0 1.61 84.0  
.59  
.31  
.18  
.12  
.05  
.03  
.77  
.40  
.24  
.15  
.07  
.04  
68.8 9.45 102.3  
65.8 6.78 10 0.4  
62.7 5.17 98.6  
59.7 4.10 96.7  
53.7 2.76 93.0  
47.6 1.96 89.3  
41.6 1.43 85.5  
.75  
.40  
.24  
.16  
.07  
.04  
.02  
.98  
.52  
.31  
.20  
.10  
.05  
.03  
102-P-L  
.21 48.5 4.99 89.8  
CFM 1499 25  
.12  
.07  
45.4 3.75 87.9  
42.4 2.91 86.1  
36.4 1.87 82.4  
RPM 850  
HP 1/8  
30  
40  
50  
60  
10  
15  
20  
70.3 14.49 89.7 1.75  
2.28  
.93  
83.7 17.24 95.4  
78.8 10.83 93.3  
2.40 3.12  
.99 1.30  
97.0 19.99 101.0 3.14 4.08  
92.1 12.66 99.0 1.32 1.72  
110.4 22.74 106.7 3.97 5.15  
105.5 14.49 104.6 1.69 2.19  
65.5 8.99 87.7  
60.6 6.24 85.6  
55.7 4.59 83.6  
50.9 3.49 81.5  
41.1 2.12 77.4  
31.4 1.29 73.3  
.71  
.36  
.20  
.12  
.05  
.02  
122-P-L  
.47 73.9 7.62 91.3  
.51  
.30  
.18  
.08  
.04  
.67  
.39  
.24  
.10  
.05  
87.3 8.99 96.9  
82.4 6.79 94.8  
77.6 5.33 92.8  
67.8 3.49 88.7  
58.1 2.39 84.6  
48.4 1.66 80.4  
.69  
.41  
.26  
.12  
.06  
.03  
.90 10 0.6 10.37 102.5  
.89 1.16  
CFM 2180 25  
RPM 1100 30  
.26  
.16  
.06  
.02  
69.1 5.69 89.2  
64.2 4.41 87.1  
54.5 2.81 83.0  
44.8 1.84 78.9  
.53  
.34  
.15  
.08  
.04  
95.8 7.89 100.5  
90.9 6.24 98.4  
81.2 4.18 94.3  
71.4 2.94 90.2  
61.7 2.12 86.1  
.53  
.34  
.16  
.08  
.05  
.70  
.45  
.21  
.11  
.06  
HP 1/6  
40  
50  
60  
10  
15  
20  
80.4 16.56 91.4 2.15  
2.89  
1.20  
95.4 19.66 97.3  
90.5 12.43 95.3  
2.92 3.92 110.4 22.76 103.1 3.78 5.08  
1.23 1.66 105.5 14.50 101.2 1.62 2.18  
125.5 25.86 109.0 4.75 6.37  
120.5 16.56 107.1 2.05 2.76  
75.4 10.36 89.5  
70.5 7.26 87.5  
65.5 5.40 85.6  
60.6 4.16 83.7  
50.7 2.61 79.8  
40.9 1.68 76.0  
.89  
.46  
.27  
.16  
.07  
.03  
146-P-L  
.62 85.5 8.81 93.4  
.65  
.38  
.24  
.11  
.87 10 0.6 10.36 99.3  
.87 1.16 115.6 11.91 105.0 1.11 1.49  
CFM 2360 25  
RPM 1100 30  
.36  
.22  
.09  
.04  
80.6 6.64 91.5  
75.6 5.20 89.5  
65.8 3.39 85.7  
55.9 2.30 81.8  
46.0 1.58 78.0  
.52  
.33  
.15  
.07  
.04  
95.6 7.88 97.3  
90.7 6.23 95.4  
80.8 4.16 91.6  
70.9 2.92 87.7  
61.1 2.10 83.8  
.52  
.34  
.16  
.08  
.04  
.70  
.45  
.21  
.11  
.06  
110.7 9.12 103.2  
105.7 7.26 101.3  
95.8 4.94 97.4  
86.0 3.54 93.6  
76.1 2.61 89.7  
.67  
.44  
.21  
.12  
.07  
.90  
.59  
.29  
.16  
.09  
HP 1/6  
40  
50  
60  
.05  
.03  
10  
15  
20  
94.6 19.50 89.9 1.98  
2.64 112.3 23.15 95.4  
1.10 106.5 14.64 93.6  
.57 10 0.7 10.38 91.8  
2.70 3.58 130.0 26.80 101.0 3.50 4.65  
1.14 1.52 124.2 17.07 99.2 1.50 1.99  
147.7 30.44 106.6 4.40 5.83  
141.9 19.50 104.8 1.90 2.52  
88.8 12.21 88.0  
83.0 8.56 86.2  
77.3 6.37 84.4  
71.5 4.91 82.6  
59.9 3.09 78.9  
.82  
.43  
.25  
.15  
.06  
166-P-L  
.60  
.35  
.22  
.10  
.05  
.02  
.80 118.4 12.21 97.4  
.47 112.7 9.29 95.6  
.30 106.9 7.34 93.7  
.80 1.06 136.1 14.03 103.0 1.02 1.36  
CFM 2920 25  
RPM 1100 30  
.33  
.20  
.09  
95.0 7.83 90.0  
89.2 6.13 88.1  
77.6 4.00 84.5  
66.0 2.72 80.8  
54.5 1.87 77.2  
.48  
.31  
.15  
.08  
.04  
.64  
.41  
.20  
.10  
.06  
130.4 10.75 101.1  
124.6 8.56 99.3  
113.0 5.82 95.7  
101.4 4.18 92.0  
89.9 3.09 88.4  
.62  
.41  
.20  
.11  
.06  
.83  
.54  
.26  
.14  
.08  
HP 1/6  
40  
50  
60  
.14  
.07  
.03  
95.3 4.91 90.1  
83.7 3.45 86.4  
72.2 2.48 82.8  
See Table SP-12 for abbreviations.  
UH-PRC001-EN  
39  
Perform ance  
Data  
Table PD-5 (Continued) – Model P-L Unit Heater Hot Water Capacities – 60°F Ent.AirTemp. (Capacities shown are for units with all Air Ports open)  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
260 F  
300 F  
340 F  
380 F  
Unit  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
Size  
Drop °F MBH GPM  
FT S.W.T. H.W.T. MBH GPM  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
42-P-L  
CFM 668  
RPM 1550 60  
HP 1/40  
50  
24.7 1.02 94.0  
.01  
.02  
32.9 1.36 105.4  
.02  
.01  
.03  
.01  
41.1 1.69 116.7  
36.2 1.24 109.9  
.03  
.02  
.04  
.02  
27.9  
.96 98.6  
42-P-L  
CFM 470  
50  
18.0  
.74 95.2  
.01  
.01  
23.7  
.98 106.4  
.01  
.01  
29.4 1.21 117.6  
.02  
.01  
.02  
.01  
RPM 1150 60  
HP 1/40  
26.1  
.90 111.2  
64-P-L  
50  
33.3 1.37 85.6  
.02  
.01  
.03  
.01  
47.3 1.95 96.3  
40.0 1.37 90.7  
.05  
.02  
.06  
.03  
61.2 2.52 107.0  
53.9 1.85 101.4  
39.4 1.01 90.3  
.07  
.04  
.01  
.10  
.05  
.02  
75.2 3.10 117.7  
67.9 2.33 112.1  
53.3 1.37 101.0  
.11  
.06  
.02  
.01  
.14  
.08  
.03  
.01  
CFM 1200 60  
RPM 1550 80  
26.1  
.90 80.0  
HP 1/20  
100  
38.8  
.80 89.8  
64-P-L  
50  
60  
26.5 1.09 88.3  
.02  
.02  
37.3 1.54 99.9  
31.8 1.09 94.0  
.03  
.02  
.04  
.02  
48.2 1.99 111.5  
42.6 1.46 105.6  
.05  
.03  
.01  
.06  
.03  
.01  
59.0 2.43 123.1  
53.5 1.84 117.2  
42.4 1.09 105.3  
.07  
.04  
.01  
.09  
.05  
.02  
CFM 862  
RPM 1150 80  
HP 1/20  
31.5  
.81 93.7  
80-P-L  
50  
39.7 1.64 86.9  
31.2 1.07 81.2  
.02  
.01  
.03  
.01  
56.1 2.31 98.0  
47.6 1.64 92.3  
.04  
.02  
.05  
.03  
72.5 2.99 109.1  
64.0 2.20 103.4  
47.1 1.21 91.9  
.06  
.04  
.01  
.08  
.05  
.01  
88.9 3.66 120.3  
80.4 2.76 114.5  
63.5 1.64 103.0  
.09  
.05  
02  
.12  
.07  
.03  
.01  
CFM 1360 60  
RPM 1550 80  
HP 1/20  
100  
46.6  
.96 91.6  
.01  
80-P-L  
50  
60  
31.6 1.30 89.3  
.01  
.02  
44.5 1.83 101.2  
37.9 1.30 95.1  
.03  
.01  
.03  
.02  
57.4 2.36 113.1  
50.8 1.75 107.1  
.04  
.02  
.01  
.05  
.03  
.01  
70.2 2.89 125.1  
63.7 2.19 119.0  
50.6 1.30 106.8  
.06  
.03  
.01  
.08  
.04  
.02  
CFM 995  
RPM 1150 80  
HP 1/20  
37.7  
.97 94.9  
102-P-L  
50  
65.2 2.69 94.3  
57.9 1.99 90.5  
43.4 1.12 82.9  
.07  
.04  
.01  
.09  
.05  
.02  
85.4 3.52 104.9  
78.2 2.69 101.1  
63.7 1.64 93.5  
49.2 1.01 85.9  
.11  
.07  
.03  
.01  
.15 105.7 4.36 115.6  
.17  
.10  
.04  
.02  
.01  
.22  
.13  
.06  
.03  
.01  
126.0 5.19 126.3  
118.7 4.08 122.5  
104.3 2.69 114.8  
89.8 1.85 107.2  
75.3 1.29 99.6  
.23  
.14  
.07  
.03  
.02  
.30  
.19  
.09  
04  
CFM 1752 60  
RPM 1070 80  
.09  
.04  
.01  
98.5 3.38 111.8  
84.0 2.16 104.2  
69.5 1.43 96.6  
HP 1/8  
100  
120  
55.0  
.95 88.9  
.02  
50  
60  
56.3 2.32 94.6  
50.2 1.72 90.9  
.05  
.03  
.07  
.04  
73.6 3.03 105.2  
67.5 2.32 101.5  
55.4 1.43 94.1  
.09  
.05  
.02  
.11  
.07  
.03  
90.9 3.75 115.9  
84.8 2.91 112.2  
72.7 1.87 104.7  
60.6 1.25 97.3  
.12  
.08  
.03  
.02  
.16  
.10  
.04  
.02  
108.2 4.46 126.5  
102.1 3.51 122.8  
90.0 2.32 115.3  
77.9 1.61 107.9  
65.8 1.13 100.5  
.17  
.11  
.05  
.03  
.01  
.22  
.14  
.07  
.03  
.02  
102-P-L  
CFM 1499 80  
RPM 850 100  
HP 1/8  
120  
50  
60  
84.8 3.49 95.8  
75.1 2.58 91.1  
55.6 1.43 83.5  
.11  
.06  
.02  
.15 111.5 4.59 107.1  
.08 101.7 3.49 103.0  
.19  
.11  
.04  
.02  
.24 138.2 5.69 118.4  
.15 128.4 4.41 114.3  
.06 109.0 2.81 106.1  
.28  
.17  
.07  
.03  
.01  
.36  
.22  
.10  
.04  
.02  
164.8 6.79 129.7  
155.1 5.33 125.6  
135.7 3.49 117.4  
116.2 2.39 109.1  
96.7 1.66 100.9  
77.3 1.14 92.7  
.38  
.24  
.11  
.05  
.03  
.01  
.49  
.31  
.14  
.07  
.04  
.02  
122-P-L  
CFM 2180 80  
RPM 1100 100  
.03  
82.3 2.12 94.8  
62.8 1.29 86.6  
.02  
89.5 1.84 97.8  
70.0 1.20 89.6  
HP 1/6  
120  
140  
50  
60  
80  
101.0 4.16 99.4  
91.1 3.13 95.6  
71.4 1.84 87.9  
.15  
.09  
.03  
.21 131.1 5.40 111.2  
.12 121.2 4.16 107.3  
.05 101.5 2.61 99.6  
.24  
.15  
.06  
.03  
.33 161.2 6.64 122.9  
.20 151.3 5.20 119.1  
.09 131.5 3.39 111.4  
.04 111.8 2.30 103.7  
.35  
.22  
.01  
.05  
.02  
.01  
.47  
.30  
.14  
.07  
.03  
.02  
191.2 7.88 134.7  
181.4 6.23 130.8  
161.6 4.16 123.1  
141.9 2.92 115.4  
122.1 2.10 107.7  
102.4 1.51 100.0  
82.6 1.06 92.3  
.48  
.31  
.15  
.08  
.04  
.02  
.01  
.64  
.41  
.19  
.10  
.05  
.03  
.02  
146-P-L  
CFM 2360 100  
RPM 1100 120  
81.7 1.68 91.9  
92.0 1.58 95.9  
72.3 1.06 88.2  
HP 1/6  
140  
160  
50  
60  
80  
119.1 4.91 97.6  
107.6 3.69 93.9  
84.4 2.17 86.6  
.14  
.08  
.03  
.19 154.5 6.37 108.8  
.11 142.9 4.91 105.1  
.04 119.8 3.09 97.8  
.23  
.14  
.06  
.03  
.30 189.9 7.83 119.9  
.19 178.3 6.13 116.3  
.08 155.2 4.00 109.0  
.03 132.1 2.72 101.7  
.33  
.21  
.09  
.05  
.02  
.01  
.43  
.27  
.12  
.06  
.03  
.01  
225.3 9.29 131.1  
213.7 7.34 127.5  
190.6 4.91 120.2  
167.5 3.45 112.9  
144.3 2.48 105.6  
121.2 1.78 98.2  
98.0 1.26 90.9  
.44  
.28  
.13  
.07  
.04  
.02  
.01  
.59  
.38  
.18  
.09  
.05  
.03  
.01  
166-P-L  
CFM 2920 100  
RPM 1100 120  
96.7 1.99 90.5  
108.9 1.87 94.4  
85.8 1.26 87.1  
HP 1/6  
140  
160  
40  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-5 (Continued) – Model P-L Unit Heater Hot Water Capacities – 60°F Ent.AirTemp. (Capacities shown are for units with all Air Ports open)  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
180 F  
200 F  
220 F  
240 F  
Unit  
Size  
PD  
FT S.W.T. H.W.T. MBH GPM  
114.3 23.56 91.1 2.83 3.76 135.8 27.98 96.9  
107.2 14.73 89.1 1.17  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
Drop °F MBH GPM  
FT S.W.T. H.W.T MBH GPM  
FT S.W.T. H.W.T  
MBH GPM  
FT S.W.T. H.W.T.  
10  
15  
3.85 5.11 157.2 32.39 102.7 5.01 6.64  
1.63 2.16 150.1 20.62 100.8 2.14 2.84  
1.56 128.6 17.67 95.0  
.80 121.5 12.52 93.0  
.46 114.4 9.43 91.1  
.28 107.3 7.37 89.2  
171.5 23.56 106.6 2.72 3.60  
202-P-L  
20 10 0.1 10.32 87.2  
.60  
.35  
.21  
.09  
.04  
.85 1.13 142.9 14.73 98.9 1.14 1.51 164.4 16.94 104.7 1.46 1.94  
CFM 3390 25  
RPM 1100 30  
93.0 7.67 85.3  
85.9 5.90 83.3  
71.6 3.69 79.5  
57.4 2.37 75.6  
.50  
.32  
.14  
.07  
.03  
.67 135.8 11.20 96.9  
.42 128.7 8.84 95.0  
.19 114.5 5.90 91.1  
.09 100.3 4.13 87.3  
.68  
.44  
.21  
.11  
.06  
.91  
.58  
.27  
.14  
.06  
157.3 12.96 102.8  
150.1 10.32 100.8  
135.9 7.00 97.0  
121.7 5.02 93.1  
107.5 3.69 89.2  
.88 1.18  
.58  
.28  
.15  
.09  
.77  
.37  
.20  
.11  
HP 1/4  
40  
50  
60  
.12  
.05  
93.1 4.80 85.3  
78.8 3.25 81.4  
64.6 2.22 77.6  
.05  
86.0 2.96 83.4  
10  
15  
142.3 29.33 89.1 5.01  
135.0 18.54 87.6 2.13  
6.66 168.5 34.72 94.5  
2.84 161.1 22.14 93.0  
6.75 8.98  
2.91 3.88 187.3 25.73 98.3 3.80 5.05  
213.5 29.33 103.7 4.78 6.36  
252-P-L  
20 127.6 13.15 86.1 1.12 1.50 153.8 15.85 91.4 1.56 2.08 180.0 18.54 96.8 2.06 2.74 206.1 21.24 102.2 2.62 3.48  
CFM 4507 25  
RPM 1100 30  
120.3 9.92 84.6  
112.9 7.76 83.1  
98.3 5.06 80.1  
83.6 3.44 77.1  
68.9 2.37 74.1  
.67  
.42  
.19  
.09  
.05  
.89 146.4 12.07 89.9  
.57 139.1 9.56 88.4  
.26 124.4 6.41 85.4  
.13 109.7 4.52 82.4  
.94 1.26 172.6 14.23 95.3 1.26 1.68  
198.8 16.39 100.6 1.61 2.15  
191.4 13.15 99.1 1.07 1.43  
176.7 9.11 96.1  
162.1 6.68 93.1  
147.4 5.06 90.1  
.61  
.29  
.15  
.08  
.82 165.3 11.35 93.8  
.39 150.6 7.76 90.8  
.21 135.9 5.60 87.8  
.11 121.2 4.16 84.8  
.83 1.10  
HP 1/4  
40  
50  
60  
.41  
.22  
.13  
.55  
.30  
.17  
.54  
.31  
.18  
.72  
.41  
.24  
.06  
95.0 3.26 79.4  
10  
15  
166.9 34.40 90.5 6.75  
158.1 21.73 88.9 2.86  
8.98  
3.82 188.9 25.95 94.5  
3.92 5.22 219.6 30.17 100.2 5.12 6.80  
250.3 34.40 105.8 6.45 8.57  
280-P-L  
20 149.4 15.40 87.3 1.51 2.01 180.1 18.56 92.9 2.10 2.80 210.9 21.73 98.6 2.77 3.69 241.6 24.90 104.2 3.52 4.69  
CFM 5040 25  
RPM 1100 30  
140.7 11.60 85.7  
131.9 9.06 84.1  
114.5 5.90 80.9  
97.0 4.00 77.7  
79.5 2.73 74.5  
.89  
.57  
.26  
.12  
.06  
1.19 171.4 14.13 91.3  
.75 162.7 11.18 89.7  
.34 145.2 7.48 86.6  
.17 127.7 5.26 83.4  
.08 110.2 3.79 80.2  
1.26 1.68 202.1 16.66 97.0 1.69 2.25  
.82 1.09 193.4 13.29 95.4 1.11 1.48  
232.9 19.20 102.6 2.17 2.89  
224.1 15.40 101.0 1.44 1.92  
HP 1/2  
40  
50  
60  
.39  
.20  
.11  
.52 175.9 9.06 92.2  
.27 158.4 6.53 89.0  
.15 141.0 4.84 86.5  
.55  
.30  
.17  
.73  
.40  
.23  
206.6 10.65 97.8  
189.2 7.80 94.6  
171.7 5.90 91.4  
.73  
.41  
.24  
.97  
.54  
.32  
15  
184.9 25.41 89.9 3.84  
5.11 220.9 30.35 95.7  
5.26 6.99 256.9 35.30 101.5 6.87 9.13  
20 174.6 17.99 88.2 2.02 2.69 210.6 21.70 94.1 2.81 3.74 246.6 25.41 99.9 3.71 4.94 282.6 29.12 105.7 4.73 6.28  
336-P-L  
25  
164.3 13.54 86.6 1.19  
1.59 200.2 16.51 92.4  
1.00 189.9 13.05 90.7  
.45 169.2 8.72 87.4  
.22 148.6 6.12 84.0  
.11 127.9 4.39 80.7  
1.69 2.25 236.2 19.48 98.2 2.26 3.01  
1.09 1.46 225.9 15.52 96.5 1.48 1.98  
272.2 22.44 104.0 2.91 3.87  
261.9 17.99 102.3 1.92 2.56  
241.2 12.43 99.0  
220.5 9.09 95.7  
199.9 6.87 92.3  
CFM 5700 30  
RPM 1140 40  
153.9 10.57 84.9  
133.3 6.87 81.5  
112.6 4.64 78.2  
91.9 3.16 74.9  
.75  
.34  
.16  
.08  
.52  
.27  
.15  
.69 205.2 10.57 93.2  
.36 184.6 7.61 89.8  
.20 163.9 5.63 86.5  
.73  
.40  
.23  
.97  
.53  
.30  
.97 1.29  
.54  
.32  
HP 3/4  
50  
60  
.72  
.43  
15  
218.3 29.99 90.5 3.82  
5.13 260.7 35.82 96.4  
5.24 7.04 303.2 41.66 102.3 6.86 9.20  
20 206.1 21.24 88.8 2.01 2.70 248.5 25.61 94.7 2.80 3.76 291.0 29.99 10 0.6 3.70 4.97 333.5 34.36 106.6 4.72 6.33  
384-P-L  
25  
193.9 15.98 87.1 1.18  
1.59 236.4 19.49 93.0  
1.00 224.2 15.40 91.3  
.45 199.8 10.30 87.9  
.22 175.4 7.23 84.5  
.11 151.1 5.19 81.1  
1.68 2.26 278.8 22.99 98.9 2.25 3.03  
1.09 1.46 266.6 18.32 97.2 1.48 1.98  
321.3 26.49 104.9 2.90 3.89  
309.1 21.24 103.2 1.92 2.57  
284.7 14.67 99.8  
260.4 10.73 96.4  
236.0 8.11 93.0  
CFM 6600 30  
RPM 1140 40  
181.7 12.48 85.4  
157.3 8.11 82.0  
133.0 5.48 78.6  
108.6 3.73 75.2  
.75  
.34  
.16  
.08  
.51  
.27  
.14  
.69 242.3 12.48 93.8  
.36 217.9 8.98 90.4  
.20 193.6 6.65 87.0  
.72  
.39  
.23  
.97  
.53  
.30  
.96 1.29  
.54  
.32  
HP 3/4  
50  
60  
.72  
.43  
15  
272.3 37.42 86.8 5.77  
7.85  
20 257.9 26.58 85.3 3.06 4.16 310.5 32.0 0 90.5 4.23 5.76 363.1 37.42 95.7 5.57 7.58  
500-P-L  
25  
243.5 20.07 83.9 1.82  
229.1 15.74 82.5 1.16  
2.47 296.1 24.41 89.1  
1.58 281.7 19.35 87.7  
.73 252.8 13.03 84.8  
.36 224.0 9.23 82.0  
.19 195.2 6.70 79.2  
2.56 3.49 348.7 28.75 94.3 3.41 4.65  
1.67 2.27 334.3 22.97 92.8 2.25 3.07  
.80 1.09 305.4 15.74 90.0 1.12 1.52  
.43  
.24  
401.3 33.08 99.4 4.37 5.94  
386.9 26.58 98.0 2.91 3.96  
358.0 18.45 95.2 1.48 2.01  
CFM 9380 30  
RPM 1160 40  
200.2 10.32 79.7  
171.4 7.06 76.8  
142.6 4.90 74.0  
.53  
.27  
.14  
HP 1-1/2  
50  
60  
.58 276.6 11.40 87.2  
.32 247.8 8.51 84.3  
.62  
.36  
.84  
329.2 13.57 92.3  
.84 1.14  
.51  
.49 300.4 10.32 89.5  
.69  
15  
330.6 45.43 89.6 5.01  
6.54 394.4 54.19 95.3  
6.83 8.91  
20 313.2 32.28 88.0 2.65 3.47 377.0 38.85 93.7 3.68 4.80 440.8 45.43 99.4 4.84 6.32 504.6 52.0 0 105.2 6.14 8.0 0  
600-P-L  
25  
295.8 24.39 86.5 1.58  
278.4 19.13 84.9 1.01  
2.07 359.6 29.65 92.2  
1.32 342.2 23.51 90.6  
.61 307.4 15.84 87.5  
.30 272.6 11.24 84.4  
.16 237.8 8.17 81.3  
2.23 2.91 423.4 34.91 97.9 2.97 3.87  
1.45 1.90 406.0 27.89 96.3 1.96 2.56  
487.2 40.17 103.6 3.79 4.95  
469.8 32.28 102.0 2.53 3.30  
435.0 22.41 98.9 1.29 1.68  
CFM 10,300 30  
RPM 1160 40  
243.6 12.55 81.8  
208.8 8.61 78.7  
174.0 5.98 75.6  
.46  
.23  
.12  
.70  
.37  
.21  
.92 371.2 19.13 93.2  
.49 336.4 13.87 90.1  
.27 301.6 10.36 87.0  
.97 1.27  
.54  
.31  
HP 1-1/2  
50  
60  
.70 400.2 16.50 95.8  
.41  
.73  
.44  
.95  
.58  
365.4 12.55 92.7  
15  
397.9 54.68 90.8 5.60  
7.67  
20 376.9 38.84 89.2 2.97 4.06 453.7 46.76 95.1 4.11 5.63 530.6 54.68 101.1 5.41 7.42 607.4 62.60 107.0 6.86 9.42  
720-P-L  
25  
355.9 29.34 87.6 1.77  
334.8 23.00 85.9 1.13  
2.41 432.7 35.67 93.5  
1.54 411.7 28.28 91.9  
.70 369.6 19.04 88.6  
.35 327.5 13.50 85.4  
.18 285.4 9.80 82.1  
2.49 3.40 509.6 42.01 99.5 3.32 4.54  
1.62 2.21 488.5 33.56 97.8 2.19 2.99  
.78 1.06 446.4 23.00 94.6 1.09 1.48  
.42  
.23  
586.4 48.34 105.4 4.24 5.82  
565.4 38.84 103.8 2.83 3.87  
523.3 26.96 100.5 1.44 1.96  
481.2 19.83 97.3  
439.1 15.08 94.0  
CFM 11,900 30  
RPM 1165 40  
292.7 15.08 82.7  
250.7 10.33 79.4  
208.6 7.17 76.2  
.52  
.26  
.13  
HP 3  
50  
60  
.56 404.4 16.67 91.3  
.31 362.3 12.44 88.1  
.60  
.35  
.82  
.48  
.82 1.11  
.49 .67  
UH-PRC001-EN  
41  
Perform ance  
Data  
Table PD-5 (Continued) – Model P-L Unit Heater Hot Water Capacities – 60°F Ent.AirTemp. (Capacities shown are for units with all Air Ports open)  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
50  
60  
80  
260 F  
300 F  
340 F  
380 F  
Unit  
Size  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T. MBH GPM  
143.1 5.90 98.9  
128.9 4.43 95.0  
100.4 2.59 87.3  
FT S.W.T. H.W.T MBH GPM  
.27 186.0 7.67 110.6  
FT S.W.T. H.W.T  
.43 228.8 9.43 122.2  
MBH GPM  
FT S.W.T. H.W.T.  
.20  
.12  
.04  
.32  
.20  
.08  
.04  
.02  
.46  
.29  
.13  
.06  
.03  
.01  
.61  
.39  
.17  
271.7 11.20 133.9  
257.4 8.84 130.0  
229.0 5.90 122.3  
.63  
.40  
.19  
.10  
.05  
.03  
.01  
.83  
.54  
.25  
.13  
.07  
.04  
.02  
.16 171.7 5.90 106.7  
.06 143.3 3.69 99.0  
.26 214.6 7.37 118.3  
.11 186.1 4.80 110.6  
.05 157.7 3.25 102.9  
.02 129.2 2.22 95.1  
202-P-L  
CFM 3390 100  
RPM 1100 120  
114.8 2.37 91.2  
86.4 1.48 83.5  
.08 200.5 4.13 114.5  
.04  
.02  
172.1 2.96 106.8  
143.6 2.11 99.0  
115.2 1.48 91.3  
HP 1/4  
140  
160  
100.8 1.48 87.4  
50  
60  
80  
188.2 7.76 98.5  
173.5 5.96 95.5  
144.2 3.71 89.5  
114.8 2.37 83.5  
.40  
.24  
.10  
.04  
.53 240.6 9.92 109.2  
.33 225.9 7.76 106.2  
.14 196.5 5.06 100.2  
.06 167.1 3.44 94.2  
.61  
.39  
.18  
.09  
.04  
.02  
.81 292.9 12.07 119.9  
.52 278.2 9.56 116.9  
.24 248.8 6.41 110.9  
.12 219.5 4.52 104.9  
.06 190.1 3.26 98.9  
.03 160.7 2.37 92.9  
.86 1.15  
345.2 14.23 130.6 1.15 1.53  
.56  
.27  
.14  
.08  
.04  
.02  
.74  
.36  
.19  
.10  
.06  
.03  
330.5 11.35 127.6  
301.2 7.76 121.6  
271.8 5.60 115.6  
242.4 4.16 109.6  
213.1 3.14 103.6  
183.7 2.37 97.6  
154.3 1.77 91.6  
.76 1.01  
252-P-L  
.37  
.20  
.12  
.07  
.04  
.02  
.50  
.27  
.16  
.09  
.06  
.03  
FM 4507 100  
RPM 1100 120  
137.8 2.37 88.2  
108.4 1.60 82.2  
HP 1/4  
140  
160  
180  
131.4 1.69 86.9  
50  
60  
80  
219.9 9.06 100.2  
202.4 6.95 97.0  
167.5 4.31 90.6  
132.5 2.73 84.2  
.53  
.33  
.13  
.06  
.71 281.4 11.60 111.5  
.43 263.9 9.06 108.3  
.18 228.9 5.90 101.9  
.08 194.0 4.00 95.5  
.82 1.09 342.8 14.13 122.7 1.16 1.54  
404.3 16.66 133.9 1.55 2.06  
386.8 13.29 130.7 1.01 1.35  
.52  
.23  
.11  
.06  
.03  
.69 325.3 11.18 119.5  
.31 290.4 7.48 113.1  
.15 255.4 5.26 106.7  
.08 220.5 3.79 100.3  
.04 185.5 2.73 93.9  
.75 1.00  
280-P-L  
.36  
.19  
.10  
.06  
.03  
.47  
.25  
.14  
.07  
.04  
351.8 9.06 124.3  
316.9 6.53 117.9  
281.9 4.84 111.6  
247.0 3.64 105.2  
212.0 2.73 98.8  
177.1 2.03 92.4  
142.2 1.46 86.0  
.50  
.27  
.16  
.09  
.05  
.03  
.02  
.66  
.36  
.21  
.12  
.07  
.04  
.02  
FM 5040 100  
RPM 1100 120  
159.0 2.73 89.1  
124.1 1.83 82.7  
HP 1/2  
140  
160  
180  
200  
150.6 1.94 87.5  
50  
60  
256.5 10.57 101.5  
235.9 8.10 98.1  
194.5 5.01 91.5  
153.2 3.16 84.8  
111.8 1.92 78.1  
.71  
.43  
.18  
.08  
.03  
.94 328.5 13.54 113.1  
.58 307.8 10.57 109.8  
.24 266.5 6.87 103.1  
.10 225.2 4.64 96.4  
.04 183.8 3.16 89.7  
1.09 1.46 400.5 16.51 124.8 1.55 2.06  
472.5 19.48 136.4 2.07 2.76  
451.8 15.52 133.1 1.36 1.81  
.69  
.31  
.15  
.07  
.04  
.92 379.8 13.05 121.4 1.00 1.33  
80  
.41 338.5 8.72 114.7  
.20 297.1 6.12 108.0  
.10 255.8 4.39 101.4  
.05 214.5 3.16 94.7  
.47  
.25  
.13  
.07  
.04  
.63  
.33  
.18  
.10  
.05  
410.5 10.57 126.4  
369.1 7.61 119.7  
327.8 5.63 113.0  
286.4 4.22 106.3  
245.1 3.16 99.6  
203.8 2.33 92.9  
162.4 1.67 86.3  
.66  
.36  
.21  
.12  
.07  
.04  
.02  
.89  
.48  
.28  
.16  
.10  
.05  
.03  
336-P-L  
100  
CFM 5700 120  
RPM 1140 140  
142.5 2.10 83.0  
HP 3/4  
160  
180  
200  
173.1 2.23 88.0  
42  
UH-PRC001-EN  
Perform ance  
Data  
Table PD-5 (Continued) – Model P-L Unit Heater Hot Water Capacities – 60°F Ent. AirTemp. (Capacities shown are for units with all Air Ports open)  
(Conversion Factors inTable SP-11 Apply Only to 200 F Entering WaterTemperature Columns)  
Entering WaterTemperature  
Water  
Temp.  
Drop °F MBH GPM  
50  
60  
80  
260 F  
300 F  
340 F  
380 F  
Unit  
Size  
PD  
PD  
PD  
FT S.W.T. H.W.T MBH GPM  
.95 387.8 15.98 114.2 1.09 1.46 472.7 19.49 126.0 1.55 2.08  
PD  
PD  
PD  
PD  
PD  
FT S.W.T. H.W.T. MBH GPM  
302.8 12.48 102.3  
278.5 9.57 98.9  
229.8 5.92 92.1  
181.0 3.73 85.3  
132.3 2.27 78.5  
FT S.W.T. H.W.T  
MBH GPM  
557.6 22.99 137.9 2.07 2.78  
533.3 18.32 134.5 1.35 1.82  
484.6 12.48 127.7  
435.8 8.98 120.9  
387.1 6.65 114.1  
338.4 4.98 107.3  
289.7 3.73 100.4  
240.9 2.76 93.6  
192.2 1.98 86.8  
FT S.W.T. H.W.T.  
.70  
.43  
.18  
.08  
.03  
.58 363.4 12.48 110.7  
.24 314.7 8.11 103.9  
.10 266.0 5.48 97.1  
.04 217.2 3.73 90.3  
.69  
.31  
.15  
.07  
.03  
.92 448.3 15.40 122.6 1.00 1.34  
384-P-L  
.42 399.6 10.30 115.8  
.20 350.9 7.23 109.0  
.10 302.2 5.19 102.2  
.05 253.5 3.73 95.4  
.47  
.24  
.13  
.07  
.04  
.63  
.33  
.18  
.10  
.05  
.66  
.36  
.21  
.12  
.07  
.04  
.02  
.89  
.48  
.28  
.16  
.10  
.05  
.03  
CFM 6600 100  
RPM 1140 120  
HP 3/4  
140  
160  
180  
200  
168.5 2.48 83.5  
204.7 2.64 88.6  
50  
60  
80  
381.8 15.74 97.5 1.09  
1.48 487.0 20.07 107.9  
.92 458.2 15.74 105.0  
.39 400.5 10.32 99.3  
.17 342.8 7.06 93.7  
.07 285.1 4.90 88.0  
1.66 2.26 592.2 24.41 118.2 2.34 3.19  
1.06 1.44 563.4 19.35 115.4 1.52 2.07  
697.4 28.75 128.5 3.11 4.24  
668.6 22.97 125.7 2.05 2.79  
610.9 15.74 120.0 1.02 1.39  
353.0 12.12 94.7  
295.3 7.61 89.0  
237.6 4.90 83.3  
179.9 3.09 77.7  
.67  
.29  
.13  
.06  
500-P-L  
.49  
.24  
.12  
.06  
.66 505.7 13.03 109.7  
.33 448.0 9.23 104.0  
.17 390.3 6.70 98.4  
.08 332.6 4.90 92.7  
.73 1.00  
CFM 9380 100  
RPM 1160 120  
.39  
.22  
.12  
.07  
.04  
.53  
.29  
.17  
.09  
.05  
553.2 11.40 114.4  
495.5 8.51 108.7  
437.8 6.45 103.0  
380.1 4.90 97.4  
322.5 3.69 91.7  
264.8 2.73 86.0  
.56  
.33  
.20  
.12  
.07  
.04  
.76  
.45  
.27  
.16  
.10  
.06  
HP 1-1/2  
140  
160  
180  
200  
227.4 3.35 82.3  
274.9 3.54 87.0  
217.3 2.49 81.3  
50  
60  
80  
464.0 19.13 101.5  
429.2 14.74 98.4  
359.6 9.26 92.2  
290.0 5.98 86.0  
220.4 3.79 79.7  
.95  
.59  
.25  
.11  
.05  
1.24 591.6 24.39 112.9  
.77 556.8 19.13 109.8  
.33 487.2 12.55 103.6  
.15 417.6 8.61 97.4  
.06 348.0 5.98 91.1  
1.45 1.89 719.2 29.65 124.4 2.04 2.66  
.92 1.21 684.4 23.51 121.2 1.32 1.73  
846.9 34.91 135.8 2.71 3.53  
812.1 27.89 132.7 1.78 2.33  
600-P-L  
.42  
.21  
.11  
.05  
.56 614.8 15.84 115.0  
.28 545.2 11.24 108.8  
.14 475.6 8.17 102.6  
.07 406.0 5.98 96.3  
.64  
.34  
.19  
.11  
.06  
.03  
.83  
.44  
.25  
.14  
.08  
.04  
742.4 19.13 126.4  
672.8 13.87 120.2  
603.2 10.36 114.0  
533.6 7.86 107.8  
464.0 5.98 101.5  
394.4 4.52 95.3  
324.8 3.35 89.1  
.89 1.16  
CFM 10,300 100  
RPM 1160 120  
.49  
.29  
.17  
.10  
.06  
.04  
.64  
.37  
.23  
.14  
.08  
.05  
HP 1-1/2  
140  
160  
180  
200  
278.4 4.10 84.9  
336.4 4.33 90.1  
266.8 3.06 83.9  
50  
60  
80  
558.0 23.00 103.2 1.06  
1.44 711.7 29.34 115.1  
.89 669.6 23.00 111.9  
.38 585.5 15.08 105.3  
.17 501.3 10.33 98.8  
.07 417.2 7.17 92.3  
- 333.0 4.90 85.8  
1.62 2.21 865.4 35.67 127.0 2.27 3.12 1019.1 42.01 138.9 3.03 4.16  
1.03 1.41 823.3 28.28 123.8 1.48 2.03 977.0 33.56 135.7 1.99 2.74  
516.0 17.72 100.0  
431.8 11.12 93.4  
347.6 7.17 86.9  
263.5 4.53 80.4  
.65  
.28  
.12  
.05  
720-P-L  
.47  
.24  
.12  
.06  
.65 739.2 19.04 117.2  
.32 655.0 13.50 110.7  
.16 570.9 9.80 104.2  
.08 486.7 7.17 97.7  
.71  
.38  
.21  
.12  
.07  
.03  
.97  
.52  
.29  
.16  
.09  
.05  
892.9 23.00 129.2  
808.7 16.67 122.6  
724.5 12.44 116.1  
640.4 9.43 109.6  
556.2 7.17 103.1  
472.1 5.41 96.6  
387.9 4.00 90.0  
.99 1.36  
CFM 11,900 100  
RPM 1165 120  
.55  
.32  
.19  
.12  
.07  
.04  
.75  
.43  
.26  
.16  
.09  
.05  
HP 3  
140  
160  
180  
200  
402.5 5.19 91.2  
318.4 3.65 84.7  
UH-PRC001-EN  
43  
Electric  
Power  
Table EP-1 Electric Power — Model S Unit Heater — Motor  
Accessory  
Operating  
Voltage  
115/60/1  
115/60/1  
115/60/1  
115/60/1  
115/60/1  
115/60/1  
Model  
Number  
18,19,20  
Motor  
Type  
MAX  
FUSE  
15  
15  
15  
15  
15  
15  
AMP  
0.35  
2.1  
1.7**  
2.3**  
3.6**  
MCA  
0.4  
2.6  
2.1  
2.9  
HP  
RPM  
1075  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
1/50*  
1/20*  
1/8*  
1/6  
1/4  
1/2  
1/6  
1/6  
1/6  
1/6  
31,38,42,45,60  
53,69,70,77,90,100  
91,126,127,168  
137,181,186,230  
207,243,260,273,320,354  
18,19,20  
31,38,42,45,60  
53,69,70,77,90,100  
91,126,127,168  
137,181,186,230  
207,243,260,273,320,354  
400  
1550  
1550  
1100  
1100  
1100  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
4.5  
6.8  
1.2-1.4/0.7  
1.2-1.4/0.7  
1.2-1.4/0.7  
1.2-1.4/0.7  
1.5-1.8/0.9  
2.3-2.5/1.3  
3.9-4.0/2.0  
5.4**  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
0.98-1.1/0.55  
0.98-1.1/0.55  
0.98-1.1/0.55  
0.98-1.1/0.55  
1.2-1.4/0.7  
1.8-2.0/1.0  
3.1-3.2/1.6  
15-15/15  
15-15/15  
15-15/15  
15-15/15  
15-15/15  
15-15/15  
15-15/15  
1/4  
1/2  
3/4  
*Optional variable speed switch is available.  
**These motors have automatic thermal overload protection or impedance protection.  
Table EP-2 Electric Power — Model S Unit Heater — Motor  
Accessory  
Model  
Number  
Motor  
Type  
Operating  
Voltage  
MAX  
FUSE  
AMP  
MCA  
HP  
1/6  
1/6  
1/6  
1/6  
1/4  
1/2  
RPM  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
1145  
1145  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
18,19,20  
115/60/1  
115/60/1  
3.8  
3.8  
4.8  
4.8  
4.8  
4.8  
5.5  
9.8  
15  
31,38,42,45,60  
53,69,70,77,90,100  
91,126,127,168  
137,181,186,230  
207,243,260,273,320,354  
18,19,20  
15  
115/60/1  
3.8  
15  
115/60/1  
3.8  
15  
115/60/1  
4.4  
15  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
115/60/1  
7.8  
15  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
1.0-1.0/0.5  
1.0-1.0/0.5  
1.0-1.0/0.5  
1.0-1.0/0.5  
1.1-1.1/0.55  
3.1-3.2/1.6  
3.1-3.2/1.6  
1.3-1.3/0.6  
1.3-1.3/0.6  
1.3-1.3/0.6  
1.3-1.3/0.6  
1.4-1.4/0.7  
3.9-4.0/2.0  
3.9-4.0/2.0  
15-15/15 1/6  
15-15/15 1/6  
15-15/15 1/6  
15-15/15 1/6  
15-15/15 1/4  
15-15/15 3/4  
15-15/15 3/4  
31,38,42,45,60  
53,69,70,77,90,100  
91,126,127,168  
137,181,186,230  
207,243,260,273,320,354  
400  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Table EP-3Electric Power — Model S Unit Heater Motor  
Accessory  
Model  
Number  
18-230  
207,243,260,273,320,354  
400  
Motor  
Type  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Operating  
Voltage  
575/60/3  
575/60/3  
575/60/3  
MAX  
FUSE  
15  
15  
15  
AMP  
0.6  
0.8  
MCA  
0.8  
1.0  
HP  
1/3  
1/2  
3/4  
RPM  
1140  
1140  
1140  
1.3  
1.6  
CAUTION: Select appropriate AMP, MCA, and MAX FUSE for the multiple voltage motors. For example, the AMP, MCA, and MAX FUSE for Model 18 with a 230 volt Totally Enclosed motor is  
1.1, 1.4, and 15 respectively.  
44  
UH-PRC001-EN  
Electric  
Power  
Table EP-4 Electric Power — Model P Unit Heater — Motor  
Accessory  
Operating  
Voltage  
Model  
Number  
Motor  
Type  
MAX  
FUSE  
AMP  
MCA  
1.6  
HP  
RPM  
42  
64,80  
102  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
115/60/1  
1.23**  
2.1  
15  
1/40*  
1/20*  
1/8*  
1/6  
1/4  
1/4  
1/2  
1/6  
1/6  
1/6  
1/6  
1/4  
1/4  
1/2  
3/4  
1-½  
3
1550  
1550  
1070  
1100  
1100  
1100  
1100  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
1160  
1165  
115/60/1  
115/60/1  
2.6  
1.5  
15  
15  
1.2**  
122,146,166  
202  
115/60/1  
2.3**  
2.9  
15  
115/60/1  
3.6**  
4.5  
15  
252  
115/60/1  
3.6**  
4.5  
15  
280  
115/60/1  
5.4**  
6.8  
15  
42  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
0.98-1.1/0.55  
0.98-1.1/0.55  
0.98-1.1/0.55  
0.98-1.1/0.55  
1.2-1.4/0.7  
1.2-1.4/0.7  
1.8-2.0/1.0  
3.1-3.2/1.6  
5.3-5.0/2.5  
9.9-9.8/4.9  
1.2-1.4/0.7  
1.2-1.4/0.7  
1.2-1.4/0.7  
1.2-1.4/0.7  
1.5-1.8/0.9  
1.5-1.8/0.9  
2.3-2.5/1.3  
3.9-4.0/2.0  
6.6-6.3/3.1  
12.4-12.3/6.1  
15-15/15  
15-15/15  
15-15/15  
15-15/15  
15-15/15  
15-15/15  
15-15/15  
15-15/15  
15-15/15  
20-20/15  
64,80  
102  
122,146,166  
202  
252  
280  
336,384  
500,600  
720  
*Optional variable speed switch is available.  
**These motors have automatic thermal overload protection or impedance protection.  
CAUTION: Select appropriate AMP, MCA, and MAX FUSE for the multiple voltage motors. For example, the AMP, MCA, and MAX FUSE for Model 720 with a 230 volt Totally Enclosed motor  
is 9.8, 12.3, and 20 respectively.  
Table EP-5 Electric Power — Model P Unit Heater — Motor  
Accessory  
Model  
Number  
Motor  
Type  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
Operating  
Voltage  
MAX  
FUSE  
AMP  
3.8  
MCA  
4.8  
HP  
1/6  
1/6  
1/6  
1/6  
1/4  
1/4  
1/2  
RPM  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
1140  
42  
115/60/1  
115/60/1  
15  
15  
15  
15  
15  
15  
20  
64,80  
102  
3.8  
4.8  
115/60/1  
3.8  
4.8  
122,146,166  
202  
115/60/1  
3.8  
4.8  
115/60/1  
4.4  
5.5  
252  
115/60/1  
4.4  
5.5  
280  
115/60/1  
7.8  
9.8  
42  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
208-230/460/60/3  
208-230/460/60/3  
1.0-1.0/0.5  
1.0-1.0/0.5  
1.3-1.3/0.6  
1.3-1.3/0.6  
15-15/15 1/6  
15-15/15 1/6  
64,80  
UH-PRC001-EN  
45  
Electric  
Power  
Table EP – 6 Electric Power — Model P Unit Heater — Motor  
Accessory  
Operating  
Voltage  
Model  
Number  
Motor  
Type  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
with Thermal Overload  
Explosion Proof  
MAX  
FUSE  
AMP  
MCA  
HP  
RPM  
1140  
1140  
1140  
1140  
1140  
1145  
1150  
1150  
102  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
208-230/460/60/3  
230/460/60/3  
1.0-1.0/0.5  
1.0-1.0/0.5  
1.1-1.1/0.55  
1.1-1.1/0.55  
1.9-1.9/0.95  
3.1-3.2/1.6  
5.2/2.6  
1.3-1.3/0.6  
1.3-1.3/0.6  
1.4-1.4/0.7  
1.4-1.4/0.7  
2.4-2.4/1.2  
3.9-4.0/2.0  
6.5/3.3  
15-15/15 1/6  
15-15/15 1/6  
15-15/15 1/4  
15-15/15 1/4  
15-15/15 1/2  
15-15/15 3/4  
122,146,166  
202  
252  
280  
336,384  
500,600  
720  
15/15  
1-½  
3
with Thermal Overload  
208-230/460/60/3  
10.0-10.0/5.0  
12.5-12.5/6.3  
20-20/15  
Table EP - 7 Electric Power — Model P Unit Heater — Motor  
Accessory  
Model  
Number  
42-252  
280  
336,384  
500,600  
720  
Motor  
Type  
Operating  
Voltage  
MAX  
FUSE  
15  
15  
15  
AMP  
0.6  
0.8  
1.3  
2.0  
MCA  
0.8  
1.0  
1.6  
2.5  
HP  
1/3  
1/2  
3/4  
1-½  
3
RPM  
1140  
1140  
1140  
1160  
1165  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
Totally Enclosed  
575/60/3  
575/60/3  
575/60/3  
575/60/3  
575/60/3  
15  
15  
3.75  
4.7  
CAUTION: Select appropriate AMP, MCA, and MAX FUSE for the multiple voltage motors. For example, the AMP, MCA, and MAX FUSE for Model 720 with a 230 volt Explosion Proof motor  
is 10.0, 12.5, and 20 respectively.  
46  
UH-PRC001-EN  
Dim ensions  
and Weights  
Figure DW-1  
Motor Mount Type-2  
Motor Mount Type-1  
Note:  
Motor Mount Type-1 is used on all standard single-phase m otors.  
Motor Mount Type-2 is used on three-phase, explosion proof 1 or 3-phase, and other special m otors.  
Table DW-1 – Model S Unit Heater Roughing-In Dimensions (Figure DW-1)*  
Number Of Number Of  
Fan  
Dia.  
Horizontal  
Louvers-Std.  
Louver-Fin.  
Diffusers  
Model  
A
B
C
D
DD  
205/8  
205/8  
205/8  
211/4  
211/4  
211/4  
211/4  
221/2  
221/2  
221/2  
221/2  
221/2  
221/2  
235/8  
245/8  
235/8  
245/8  
251/2  
251/2  
26  
E
6
EE  
F
G
H
25/8  
J
K
13/4  
13/4  
13/4  
2
2
2
2
2
L
18, 19 & 20 111/4  
207/8  
207/8  
207/8  
237/8  
237/8  
237/8  
237/8  
263/4  
263/4  
263/4  
263/4  
311/8  
311/8  
333/4  
333/4  
333/4  
333/4  
393/8  
393/8  
393/8  
393/8  
521/8  
521/8  
521/8  
141/4  
141/4  
141/4  
171/4  
171/4  
171/4  
171/4  
201/4  
201/4  
201/4  
201/4  
231/4  
231/4  
261/4  
261/4  
261/4  
261/4  
321/4  
321/4  
321/4  
321/4  
321/4  
321/4  
321/4  
93/8  
153/8  
161/8  
161/8  
17  
111/4  
11 1/4  
11 1/4  
111/4  
111/4  
11 1/4  
11 1/4  
11 1/4  
11 1/4  
11 1/4  
11 1/4  
11 1/4  
11 1/4  
11 1/4  
121/4  
11 1/4  
121/4  
121/4  
121/4  
123/4  
123/4  
123/4  
123/4  
123/4  
31/8  
31/8  
31/8  
31/2  
31/2  
31/2  
31/2  
41/8  
41/8  
41/8  
41/8  
41/8  
41/8  
45/8  
45/8  
45/8  
45/8  
51/8  
51/8  
51/8  
51/8  
53/8  
53/8  
53/8  
85/8  
11/4  
11/4  
11/4  
11/4  
11/4  
11/4  
11/4  
11/4  
11/4  
11/4  
11/4  
11/2  
11/2  
11/2  
11/2  
11/2  
11/2  
11/2  
11/2  
11/2  
11/2  
11/2  
11/2  
11/2  
31  
38 & 42  
45  
60  
53  
70  
69  
90  
77  
100  
91  
126  
168  
186  
127  
137  
181  
111/4  
111/4  
93/8  
63/4  
63/4  
7
85/8  
25/8  
-
4
5
3
4
93/8  
11 5/8  
11 5/8  
145/8  
11 5/8  
145/8  
145/8  
175/8  
145/8  
175/8  
145/8  
205/8  
235/8  
235/8  
175/8  
175/8  
235/8  
221/8  
235/8  
231/8  
221/8  
235/8  
221/8  
25/8  
25/8  
-
131/2  
131/2  
131/2  
131/2  
131/2  
131/2  
163/4  
163/4  
163/4  
163/4  
193/4  
193/4  
193/4  
193/4  
193/4  
193/4  
251/4  
25 1/4  
25 /4  
251/4  
251/4  
10  
10  
10  
10  
17  
7
25/8  
-
171/4  
171/4  
181/2  
181/2  
183/4  
183/4  
21  
71/4  
71/4  
71/4  
71/4  
71/2  
71/2  
93/4  
93/4  
93/4  
93/4  
93/4  
93/4  
93/4  
93/4  
111/4  
111/4  
11 1/4  
11 1/4  
-
25/8  
-
25/8  
25/8  
-
11 1/4  
11 1/4  
11 1/4  
11 1/4  
11 1/4  
11 1/4  
123/8  
123/8  
123/8  
123/8  
131/4  
131/4  
131/4  
131/4  
133/4  
133/4  
133/4  
-
6
6
5
5
25/8  
2
2
2
25/8  
25/8  
25/8  
-
25/8  
-
21/2  
21/2  
21/2  
21/2  
21/2  
21/2  
21/2  
2
21/2  
2
2
21/2  
2
21  
-
7
8
6
7
221/8  
221/8  
221/8  
221/8  
23  
25/8  
25/8  
25/8  
25/8  
25/8  
-
-
-
-
-
230  
207  
260  
320 & 354  
243 & 273  
400  
23  
25/8  
10  
9
241/2  
241/2  
25  
25/8  
26  
25/8  
25/8  
-
10  
10  
9
9
261/2  
261/2  
261/2  
-
25  
-
25/8  
25/8  
10  
9
*Note: All dimensions approximate in inches for roughing-in purposes. Detailed certified drawings available on request.  
UH-PRC001-EN  
47  
Dim ensions  
and Weights  
Table DW-2 - Model P Unit Heater Roughing In Dimensions (Figure DW-2)*  
Unit  
Size  
102  
Fan  
Dia.  
163/4  
L
P
A
251/4  
B
61/8  
C
2
D
171/2  
E
11/8  
F
3
G
17  
H
13/8  
K
23/4  
(Min.)  
7
(NPT)  
11/2  
R
41/8  
S
91/8  
T
23/4  
U
17  
V
41/8  
122  
146  
166  
202  
252  
280  
336  
384  
500  
600  
720  
163/4  
193/4  
193/4  
193/4  
251/4  
251/4  
251/4  
251/4  
30  
251/4  
291/2  
291/2  
291/2  
371/2  
371/2  
371/2  
371/2  
42  
61/8  
61/8  
61/8  
75/8  
75/8  
75/8  
75/8  
91/8  
91/8  
121/8  
135/8  
2
171/2  
205/8  
205/8  
205/8  
263/8  
263/8  
263/8  
263/8  
311/4  
311/4  
311/4  
13/4  
11/4  
13/4  
2
3
4
4
17  
201/2  
201/2  
201/2  
28  
28  
28  
28  
30  
13/8  
13/4  
13/4  
13/4  
13/4  
13/4  
13/4  
13/4  
21/4  
21/4  
21/4  
23/4  
31/2  
31/2  
31/2  
31/2  
31/2  
31/2  
31/2  
41/4  
41/4  
41/4  
7
7
7
7
7
7
7
7
7
7
7
11/2  
2
2
2
2
2
2
2
21/2  
21/2  
21/2  
41/8  
41/2  
41/2  
41/2  
43/4  
43/4  
43/4  
43/4  
6
93/4  
23/4  
23/4  
23/4  
23/4  
23/4  
23/4  
23/4  
23/4  
3
17  
201/2  
201/2  
201/2  
18  
18  
18  
18  
30  
41/8  
41/2  
41/2  
41/2  
93/4  
93/4  
93/4  
93/4  
6
23/8  
23/8  
23/8  
3
95/8  
101/8  
12  
4
1
31/2  
31/2  
4
115/8  
113/4  
123/4  
141/8  
141/4  
173/4  
201/4  
3
3
3
31/2  
31/2  
31/2  
11/4  
21/8  
2
31/2  
3
15/8  
21/8  
3
30  
30  
42  
42  
3
4
30  
30  
6
6
3
3
30  
30  
6
6
Figure DW-2  
48  
UH-PRC001-EN  
Dim ensions  
and Weights  
Table DW-3 - Model P Unit Heater Roughing In Dimensions (Figure DW-3)*  
Unit  
Size  
42  
64  
80  
Fan  
Dia.  
111/4  
131/2  
131/2  
L
P
(NPT)  
11/2  
A
B
C
D
11 3/4  
14  
E
/4  
1
1
F
4
4
3
G
11  
14  
14  
H
K
(Min.)  
R
S
T
U
11  
14  
14  
V
3
181/4  
211/4  
211/4  
45/8  
45/8  
61/8  
11/4  
15/8  
15/8  
13/8  
13/8  
13/8  
17/8  
17/8  
17/8  
7
7
7
35/8  
35/8  
35/8  
65/8  
71/8  
85/8  
23/4  
23/4  
23/4  
35/8  
35/8  
35/8  
11/2  
14  
11/2  
Figure DW-3  
Table DW-4 - Louver Cone Diffuser Roughing  
In Dimensions (Figure DW-4)*  
No. of  
Unit Size  
42  
64 & 80  
102 & 122  
146, 166 & 202  
252, 280, 336 & 384 351/2 311/2 133/4  
500, 600 & 720  
*Note:  
A
B
C
D
Louvers  
161/2 141/4 61/2  
20 17  
241/4 21  
25/8  
31/8  
8
8
8
8
12  
12  
8
93/4 315/16  
283/8 243/4 11 1/2 45/8  
4
43/4  
411/2 371/4 17  
All dimensions approximate in inches for roughing-in  
purposes. Detailed certified drawings available on request.  
Figure DW-4  
UH-PRC001-EN  
49  
Mechanical  
Specifications  
Model P  
Coils  
type with sleeve bearings. Motor for unit  
sizes 122P through 280P are permanent  
split capacitor types with permanently  
lubricated ball bearings. Motors used on  
unit sizes 336P through 720P are 230/460/  
60/3, totally enclosed, with permanently  
lubricated ball bearings. Unit sizes  
smaller than 336P are also available with  
230/400/60/3 motors.  
All motors fractional hp and integral hp,  
have Class Binsulation.The (115/60/1  
motors used as standard on unit sizes  
42P through 102P can be operated at  
multiple speeds with the addition of a  
solid-state control.  
Hot water-steam coils are rectangular  
3 or 4-sided, one-pass, multiple circuit,  
with aluminum Sigma-Flo® fins  
General  
The NRTLC/Cindicator adjacent to the  
CSA mark signifies that the product has  
been evaluated to the applicable ANSI/  
UL and CSA Standards, for use in the  
U.S. and Canada.  
NRTL, i.e. Nationally Recognized Testing  
Laboratory, is a designation granted by  
the U.S. Occupational Safety and Health  
Administration to laboratories which  
have been recognized to perform  
certification to U.S. Standards.  
mechanically bonded to tubes. Standard  
coils are seamless copper tubing. Coils  
tested at 375 psi under water. Supply  
and return connections are steel pipe.  
Standard coils have .025 copper tubing  
suitable for use on steam pressure to 75  
psi or hot water up to 225 psi or 325 F.  
When Specified) Heavy .049 red brass  
tubing suitable for 75 psi steam or up to  
425 deg. F water at 300 psi .049 cupro-  
nickel tubing suitable for 75 psi steam or  
up to 450 deg. F water at 400 psi .049  
steel tubing suitable for 450 deg. F water  
at 400 psi.  
Casing  
Formed by two square steel plates.  
Bottom plate forms orifice for air  
delivery. Air ports stamped in top plate  
as standard for easy removal for low  
final air temperature.  
All units available with explosion-proof  
motors. Only sizes 42P, 64P, 102P and  
146P are available from stock with  
115/60/1 explosion-proof motors.  
Motors  
Standard motors are 115/60/1, totally  
enclosed, with thermal overload  
protection for all units through size 280P.  
Standard motors for 42P, 64P and 80P  
are shaded pole, sleeve bearing.The  
102P motor is permanent split capacitor  
Fan  
Louver Cone Diffuser  
Trane high efficiency Model A fan with  
aluminum blades is quiet, factory  
balanced and sturdy for standard or  
spark-proof applications.  
(When Specified) Available for complete  
versatility in air diffusion patterns.  
Adjustable 18-gauge steel blades held in  
set position by spring steel clips.  
Model S  
Coils  
sizes have odd numbers (19, 77, 243,  
etc.).  
General  
Hot water-steam headerless coils are  
single tube, single serpentine on all sizes  
except 230 thru 354 which have two  
circuits. Fins are aluminum  
Sigma-Flo, mechanically bonded to  
seamless copper tubing. All coils  
one-row deep in air flow direction.  
Coils tested at 400 psi air under water.  
Standard coils have .031 copper tubing  
suitable for use on steam pressures to 75  
psi or hot water up to 200 psi or  
325 F.  
(When Specified) Heavy .049 red brass  
tubing suitable for 75 psi steam or 390  
deg. F water at 260 psi .031 cupro-  
nickel tubing suitable for 450 deg. F  
water at 400 psi .049 steel tubing  
suitable for 450 deg. F water at 400 psi.  
(When Specified) Coils with turbulators  
(Suffix W) available for high performance  
on hot water.  
The NRTLC/Cindicator adjacent to the  
CSA mark signifies that the product has  
been evaluated to the applicable ANSI/  
UL and CSA Standards, for use in the  
U.S. and Canada.  
NRTL, i.e. Nationally RecognizedTesting  
Laboratory, is a designation granted by  
the U.S. Occupational Safety and Health  
Administration to labortories which have  
been recognized to perform certification  
to U.S. Standards.  
Motors  
Totally enclosed, 115/60/1 Class B”  
insulated shaded pole and PSC motors  
1
are STD. 1/50 through /8 hp are sleeve  
3
bearing, 1/6 through /4 hp are ball  
bearing. All single phase motors have  
built in overload protection. Sleeve  
bearing motors can be oiled. Ball  
bearing motors are permanently  
lubricated.  
The 115/60/1 motors used as standard on  
unit sizes 18S through 100S can be  
operated at multiple speeds with the  
addition of a solid- state control.  
All units available with explosion-proof  
motors. Only sizes 18S, 42S, 90S and  
126S are available from stock with  
115/60/1 explosion-proof motors.  
Casing  
Two-piece with picture framefront  
formed into wraparound sides, top and  
bottom. Adjustable horizontal louvers  
are standard. 18 gauge back panel with  
deep-draw fan orifice for extreme  
rigidity. Steel supply and return pipe tap  
connectors bolted to back. Casings  
phosphatized to prevent corrosion and  
painted with blue gray baked enamel.  
Louver Fin Diffuser  
(When Specified) Coils with fin series  
132 (Suffix 2) for high performance on  
hot water or steam.  
(When Specified) Bypass Model S units  
with modified coils for air bypass. Unit  
(When Specified) For versatility in lateral  
diffusion, used with standard louvers,  
provides four-direction control. Ships  
separately and clips onto horizontal  
louvers.  
Fan  
Trane designed and built high efficiency  
Model A fan with aluminum blades is  
quiet, factory balanced and sturdy for  
standard or sparkproof applications.  
50  
UH-PRC001-EN  
NRTL/C  
Literature Order Number  
File Number  
UH-PRC001-EN  
PL-UN-UH-000-PRC001-10-99  
UH-DS-1 8/96  
Supersedes  
The Trane Com pany  
Unitary Products Group  
2701 Wilma Rudolph Blvd.  
Clarksville,TN 37040  
Stocking Location  
Inland - LaCrosse  
TheTrane Company has a policy of continuous product and product data improvement, it reserves the right  
to change product design and specifications without notice.  
An American Standard Company  

Tekkeon Mp3400 User Manual
Sony Found Not Kdl 37xbr6 User Manual
Sharp Air Cleaner Kc 850u User Manual
Schumacher 5216a Pe User Manual
Sanyo 24ks72 User Manual
Samsung Avmch072ca1 User Manual
Rocketfish Rf Gwii1121 User Manual
Precisionaire Gas Turbine Rigid Filters Cell Gt User Manual
KENWOOD KDC X492 User Manual
AT&T MOTOROLA MOTO Z9 User Manual