MULTIFUNCTIONAL DIGITAL SYSTEMS
Operator's Manual
for Copying Functions
EPA ENERGY STAR ® (MFD)
The United States Environmental Protection Agency (EPA) has introduced a voluntary programme, the ENERGY
STAR programme, to encourage the widespread and voluntary use of energy-efficient technologies that enhance
the workplace, improve product performance and prevent pollution. As an ENERGY STAR Partner, the TOSHIBA
TEC CORPORATION has determined that this copier model meets the ENERGY STAR guidelines for energy
efficiency.
ENERGY STAR guidelines for this class of copier require ENERGY STAR copiers to have a ‘Sleep mode’
feature that automatically makes the copier enter the sleep mode after a period of inactivity. The copier must also
automatically change to a ‘Low power mode’ after a certain period of time since the last usage.
Specifically, this copier complies with the following requirements.
Low power mode:
The equipment automatically enters this mode when a specified period of time (the default setting at the time
of shipment: 15 minutes) has passed since its last use. “Saving energy” appears on the LCD screen.
Sleep mode:
The equipment automatically enters this mode when a specified period of time (the default setting at the time
of shipment: 30 minutes) has passed since its last use. “Sleep mode” appears on the LCD screen.
A maximum of 70 W (in the sleep mode) is provided as standard power consumption in the ENERGY STAR.
The power consumption of this equipment is within the provided one both in the lower power mode and sleep
mode.
Note 1: The period from the last use to the time the equipment enters into the sleep mode or the low power mode
can be changed. See the following page for details:
P.128 “Timer Setting”
Note 2: In the sleep mode, the equipment starts warming itself up when print data are received, or when any
button on the control panel is pressed. When the warm-up has completed, the equipment enters into the
ready status and starts printing out the data.
In accordance with EPA ENERGY STAR programme guidelines, TOSHIBA recommends the following recycled
paper.
Great White MultiUse 20 paper
If you have any questions regarding the use of recycled paper or some recommended types of recycled paper,
please contact your authorized TOSHIBA dealer.
ENERGY STAR is a U.S. registered mark.
Notice to Users
After a suitable place has been selected for the installation of the e-STUDIO165/205, please do not
change it. Avoid excessive heat, dust, vibration and direct sunlight. Also, provide proper ventilation as
the copier emits a small amount of ozone.
For EU only
Warning:
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Working environment
From EMC (Electromagnetic Compatibility) point of view, the operation of this product is being restricted
in following environments:
y
Medical Environments: This product is not certified as a medical product according to the Medical
Product Directive 93/42/EEC.
y
Domestic environments (e.g. a private living room with TV / Radio sets in the nearby surrounding
area) because this is a so called EMC class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures!
Any consequences resulting from the use of this product in restricted working environments are not the
responsibility of TOSHIBA TEC.
The consequences of the use of this product in restricted working environments may be an electromag-
netic interference with other devices or machines in the nearby surrounding area. This can result into
malfunction including data loss / data error pertaining to this product or the other devices / machines
involved in the electromagnetic interference.
Furthermore, for general safety reasons, the use of this product in environments with explosive atmo-
spheres is not permitted.
CE compliance
This product is labelled with the CE mark in accordance with the provisions of the applicable European
Directives, notably the Low Voltage Directive 73/23/EEC and the Electromagnetic Compatibility Direc-
tive 2004/108/EEC for this product and the electric accessories, the Radio Equipment and Telecommu-
nications Terminal Equipment Directive 99/5/EEC for the telecommunication accessories.
CE marking is the responsibility of TOSHIBA TEC GERMANY IMAGING SYSTEMS GmbH, Carl-
Schurz-Str. 7, 41460 Neuss, Germany, phone +49-(0)-2131-1245-0.
For a copy of the related CE Declaration of Conformity please contact your dealer or TOSHIBA TEC.
For Germany only
Machine Noise Information
Ordinance 3. GPSGV: The maximum sound pressure level is equal or less than 70 dB(A) according to
EN ISO 7779
Notice to Users
1
Following information is for EU-member states only:
This product is marked according to the requirement in EU-Directive 2002/96/EC.
(Directive on Waste electrical and electronic equipment - WEEE)
The use of the symbol indicates that this product may not be disposed as unsorted municipal waste and
has to be collected separately. By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about the take-back and recycling of this product please contact your sup-
plier where you purchased the product.
2
Notice to Users
Lineup of Our Manuals
Thank you for purchasing the TOSHIBA multifunctional digital systems e-STUDIO165/205.
We have provided you with these manuals for the operation of this equipment. Select and read
the manual best suited to your needs.
Operator’s Manual for Copying Functions
This manual describes the basic operations, mainly copying
functions, of this equipment. Be sure to read this before you
use the equipment.
Operator’s Manual for TOSHIBA Viewer (PDF)
This manual describes how to use the co-packed application
software TOSHIBA Viewer, and how to print data from other
Windows applications to this equipment.
To read manuals in PDF (Portable Document Format) files
Viewing and printing this operator’s manual in PDF files require that you install Adobe Reader or
Adobe Acrobat Reader on your PC. If Adobe Reader or Adobe Acrobat Reader is not installed
on your PC, download and install it from the website of Adobe Systems Incorporated.
Lineup of Our Manuals
3
Before Reading This Manual
This operator’s manual describes the following:
y How to use this equipment
y How to inspect and carry out maintenance on this equipment
y How to remedy mechanical and copying problems
Precautions in this manual
To ensure correct and safe use of this equipment, this operator’s manual describes safety pre-
cautions according to the three levels shown below.
You should fully understand the meaning and importance of these items before reading this
manual.
Indicates a potentially hazardous situation which, if not avoided, could result
in death, serious injury, or serious damage, or fire in the equipment or sur-
rounding assets.
Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury, partial damage of the equipment or surrounding
assets, or loss of data.
Indicates a procedure you should follow to ensure the optimal performance of
the equipment and problem-free copying.
Other than the above, this manual also describes information that may be useful for the opera-
tion of this equipment with the following signage:
Describes handy information that is useful to know when operating the equip-
ment.
Pages describing items related to what you are currently doing. See these
pages as required.
4
Before Reading This Manual
Description of original/paper direction
Paper or originals of A4 or B5 size can be placed either in a portrait direction or in a landscape
direction. In this manual, “-R” is added to this paper size when this size of paper or original is
placed in a landscape direction.
e.g.) A4 size original on the original glass
Placed in a portrait direction: A4
Placed in a landscape direction: A4-R
Paper or originals of A3 or B4 size can only be placed in a landscape direction, therefore “-R” is
not added to these sizes.
Screens
Screens on this manual may differ from the actual ones depending on the use-environment of
the equipment such as the installing status of options.
Trademarks
y Microsoft and Windows are the trademarks of Microsoft Corporation in the US and other
countries.
y Adobe, Adobe Acrobat, Adobe Reader and Adobe Acrobat Reader are the trademarks of
Adobe Systems Incorporated.
y Other company or product names shown in this manual may be a brand name or a trade-
mark of each company.
©2006 TOSHIBA TEC CORPORATION All rights reserved
Under the copyright laws, this manual cannot be reproduced in any form without prior written
permission of TOSHIBA TEC CORPORATION. No patent liability is assumed, however, with
respect to the use of the information contained herein.
Before Reading This Manual
5
6
Before Reading This Manual
CONTENTS
Lineup of Our Manuals.................................................................................3
General Precautions...................................................................................16
How to Use Antiskid Devices ....................................................................21
Disclaimer Notice .......................................................................................22
Left side / Inner side ................................................................................26
“Copy mode” main screen .......................................................................32
Turning power ON ...................................................................................33
Placing paper in the drawers of Paper Feed Pedestal (optional) ............41
Registering standard size (A3, A4, A4-R, A5-R, B4)...............................45
Acceptable originals ................................................................................50
Placing booklet-type originals such as books or catalogues ...................52
Placing originals on Reversing Automatic Document Feeder (optional) /
Automatic Document Feeder (optional)...................................................54
Making Copies ............................................................................................55
Stopping/Resuming copying....................................................................57
CONTENTS
7
Interrupting copying and making another copy - Interrupt copy - ............58
Preparation - Registering paper size placed on bypass tray...................60
Before Making Copies................................................................................68
Confirming set functions..........................................................................68
Paper Selection...........................................................................................69
Automatic paper selection (APS).............................................................69
Manual paper selection ...........................................................................70
Automatic magnification selection (AMS)................................................74
Specifying both the sizes of the original and the copy paper ..................76
Specifying reproduction ratio manually....................................................77
Selecting Image Mode................................................................................79
Adjusting Density Level.............................................................................80
Copy Menu ..................................................................................................82
Operating in copy menu ..........................................................................82
Copying on one side................................................................................93
Copying on both sides.............................................................................94
Printing Page Number, Date and Time - ANNOTATION - .....................101
Changing Copy Setting on Each Job - JOB BUILD - ............................102
Copying 2 or 4 Pages into 1 Page - 2IN1/4IN1 - ....................................104
8
CONTENTS
Changing Sizes in Horizontal and Vertical Directions - XY ZOOM - ...109
Registering combination of functions.....................................................111
Operating buttons for changing the settings..........................................118
Date and Time...........................................................................................119
Clock setting..........................................................................................119
Date and time display............................................................................121
Paper Size Setting ....................................................................................124
Walkup Screen Setting.............................................................................126
Timer Setting.............................................................................................128
Time of automatic function clear............................................................128
Time of automatic low power mode.......................................................130
Volume Adjustment..................................................................................137
Touch Key Tone Setting ..........................................................................139
Clearing counter values.........................................................................150
Printing out counter values....................................................................152
Menu Customize.......................................................................................155
APS / AMS .................................................................................................157
Image Mode...............................................................................................159
Density Adjustment..................................................................................161
Finishing Mode .........................................................................................163
Various List Printing ................................................................................165
Menu List Printing ....................................................................................167
CONTENTS
9
Paper Jams ...............................................................................................172
Checking position of paper jams ...........................................................172
Paper jams within fuser unit ..................................................................181
Paper jams within Paper Feed Unit (optional).......................................183
General operation..................................................................................192
Original/Copy paper-related items.........................................................194
Image trouble ........................................................................................195
Daily Inspection........................................................................................198
Cleaning charger ...................................................................................199
e-STUDIO165/205 Specifications ............................................................204
Specifications of Options ........................................................................206
Packing List ..............................................................................................208
Combination Matrix 2/2..........................................................................210
List Print Format.......................................................................................211
Department code list..............................................................................211
Function list ...........................................................................................212
10 CONTENTS
Supply notice list....................................................................................213
Mailbox list.............................................................................................214
Configuration page list...........................................................................215
NIC status page list ...............................................................................216
Menu list ................................................................................................217
INDEX .......................................................................................................................................219
CONTENTS 11
12 CONTENTS
TOSHIBA Quality is Second to None
Recommended toner cartridges
To assure optimal printing performance, we recommend that you use TOSHIBA toner cartridges.
If you use a TOSHIBA-recommended toner cartridge, you can utilize the following two check
functions of this equipment:
Cartridge detecting function:
This function checks if the toner cartridge is correctly installed and notifies you if it is not.
Toner remaining check function:
This function notifies you when there is little toner remaining in the cartridge, as well as notifying
it to your service representative automatically by the remote service.
Any copying or printing operation is available even if you are using a toner cartridge other than
the one we recommend. In that case, however, the equipment cannot detect whether the toner
cartridge is installed or not and therefore an error message “Toner not recognized” appears on
the LCD screen, even if the toner cartridge is correctly installed. You cannot utilize the toner
remaining check function and the remote service function notifying your service representative
automatically either.
If you are using a toner cartridge other than the one we recommend and you feel annoyed by
this message, contact your service representative. Your service technician will cancel the car-
tridge detecting function set by default. Remember once this function has been cancelled, you
will not be able to utilize the two functions mentioned above even if you change the cartridge to
the one we recommend.
TOSHIBA Quality is Second to None 13
Supplies / Parts
Dependability
Genuine TOSHIBA supplies are subjected to the strictest of inspections so that every supply you
receive will perform at optimal levels.
High Productivity
Genuine TOSHIBA supplies are created to meet the demands of our competitive world and pro-
vide high-speed reliable copies when you need them.
Stable Image Quality
Genuine TOSHIBA supplies are designed to provide consistently stable image output.
Copier Kind
Genuine TOSHIBA supplies are designed to keep the equipment and all its parts in trouble-free
working order. Reduction of machine wear is due to TOSHIBA’s intimate knowledge of the
equipment’s characteristics ensuring the highest standard of care.
Machine Balance
From the beginning TOSHIBA supplies and machines were made for each other. Whenever
TOSHIBA designs a new machine, it also designs a new toner that is made just for that
machine. By using Genuine TOSHIBA supplies with TOSHIBA equipment, you are guaranteed
optimum performance.
Toner
Optimum Image Quality
TOSHIBA toner is manufactured using ultra-fine quality materials under precisely controlled con-
ditions to ensure that your TOSHIBA equipment will continually generate sharp high-quality
images.
Cost Advantage
Genuine TOSHIBA toner provides value. Only the proper amount of toner is used during the
reproduction process thereby enabling the machine to continue to operate until all the toner has
been used. In this way you get the full value from each cartridge used.
Environmental Harmony
Genuine TOSHIBA toner is manufactured with the environment in mind. To care for Mother
Earth, we use embossed or plastic labels making our toner cartridges fully recyclable. In addi-
tion, dust and ozone levels have been reduced to improve the working environment.
User Friendly
Before approving our toners for sale, we test them to be sure that they pass the strictest of
health standards. This takes the worry out of handling the toner.
General
Service and Support Benefits
TOSHIBA’s Service technicians are certified to keep your equipment performing at optimum lev-
els. To ensure continuous image quality, utilize an authorized TOSHIBA Service provider to care
for and perform periodical maintenance on your equipment.
14 TOSHIBA Quality is Second to None
Features of e-STUDIO165/205
A black-and-white copier the e-STUDIO165/205 has realized the copying speed of 16 copies
*1
*1
per minute (the e-STUDIO165) and also the copying speed of 20 copies per minute (the
e-STUDIO205). Both of them can be a printer and a scanner when they are connected to your
*2, *3
PC with a USB cable
.
The e-STUDIO165/205 also has functions as a Fax, a network scanner and a network printer,
namely, it remarkably saves time and space at your workplace.
Lightweight and space-saving equipment with more emphasis on basic functions
y The receiving tray is relocated to the equipment’s inner side, occupying as little space as
possible.
y Operability of the control panel has been upgraded with its larger buttons and LCD screen.
y A wide range of paper sizes from A3 to A5-R are acceptable.
y The bypass tray equipped as a standard unit makes copying on various media types such as
overhead transparencies possible.
y Scanning data with a TWAIN driver is enabled as a standard function.
y A rich variety of convenient copying functions are adopted.
Functions extended by various options
y The Reversing Automatic Document Feeder (RADF) / Automatic Document Feeder (ADF)
dramatically saves the time when you need to copy massive amounts of originals.
y The Scanner Upgrade Kit promotes paperless at your office.
y The Fax Kit can add a function as a Fax machine.
y The Network Printer Kit works as a shared printer at your office.
y The Paper Feed Unit (PFU), the Paper Feed Pedestal (PFP) and the Drawer Module can
add maximum 4 more drawers.
y The Expansion Memory can increase the maximum number of originals which can be
scanned in one go when the finishing mode is used.
Ecological energy-saving design
y A toner recycling system which produces no used toner is adopted.
y Its warm-up time is shortened to approx. 25 seconds.
y The low power mode, which reduces unnecessary electric power by having the fuser unit
temperature lowered while the equipment is left inactive, is adopted.
y The sleep mode, which maintains the smallest possible power consumption during the
equipment’s inactive period after it has not been used within a specified period of time, is
adopted.
*1 These speeds are realized in the non-sort mode, when A4 originals placed in a portrait direction are con-
tinuously copied and the Reversing Automatic Document Feeder (optional) / Automatic Document
Feeder (optional) is not used.
*2 When this equipment is used as a printer, the co-packed software needs to be installed into your PC.
*3 When the equipment is used as a network printer with the Network Printer Kit (optional) installed, it can-
not be connected with your PC with a USB cable and used as a local printer.
Features of e-STUDIO165/205 15
General Precautions
When installing or moving
Warning
y This equipment requires 220 to 240 V AC, 8 A 50/60 Hz electric power. For Saudi Arabia 100
V version, it requires 127 V AC, 12 A 50/60 Hz electric power.
Do not use a power supply with a voltage other than that specified.
Avoid multiple connections in the same outlet. This could cause a fire or give you an electric
shock. If you are considering increasing the number of outlets, contact an electrician.
y Always connect this equipment to an outlet with an earth connection to avoid the danger of
fire or electric shock in case of short-circuiting. Contact your service representative for the
details. Be sure to use a 3-conductor, grounded wall outlet.
In areas, where a 2-pin plug is used, the equipment must be grounded for safety. Never
ground it to a gas pipe, a water pipe, or any other object not suitable for grounding.
y Plug the power cable securely into the outlet. If it is not plugged in properly, it could heat up
and cause a fire or give you an electric shock.
y Do not damage, break or attempt to repair the power cable.
The following things should not be done to the power cable.
-
-
-
-
-
-
Twisting it
Bending it
Pulling it
Placing anything on it
Making it hot
Situating it near radiators or other heat sources
This could cause a fire or give you an electric shock. If the power cable is damaged, contact
your service representative.
y When removing the plug from the outlet, do not pull the power cable. Always hold the plug
when removing it from the outlet. If the power cable is pulled, the wires may become broken
and this could cause a fire or give you an electric shock.
y Make sure that the ventilation holes are not blocked up.
If the temperature within the equipment becomes too high, a fire could result.
y Do not install the equipment by yourself or try to move it once it has been installed. This
could result in an injury or damage to the device. Contact your service representative if the
equipment needs to be installed or moved.
y Pull the plug out from the outlet more than once a year to clean around the prongs. Accumu-
lating dust and dirt could cause a fire due to the heat released by electric leakage.
16 General Precautions
Caution
y Avoid placing the equipment in a place unsuitable for its weight and also make sure the sur-
face is level.
Weight of the equipment: approx. 32.5 kg
y Be sure to use the adjusters (safety stopper) to fix the equipment firmly to the floor after mov-
ing/installing it. Make certain that the equipment is steady. If it moves, it could fall over and
injure someone.
P.21 “How to Use Antiskid Devices”
y When connecting the interface cable to the equipment, be sure to turn the power OFF. If the
power is not turned off, you could get an electric shock.
Other points
y The socket outlet shall be installed near the equipment and shall be easily accessible.
y Make sure that there is enough space around the system to facilitate changing of parts,
maintenance and clearing paper jams.
If there is insufficient space, some operations, such as bypass feeding, will become difficult
and the equipment could even break down.
To insure optimal operation, allow clearances of at least 80 cm on the right, and 10 cm on the
left and behind.
10 cm
10 cm
80 cm
y Be sure to fix the power cable securely so that no one trips over it.
y Adverse environmental conditions may affect the safe operation and performance of the
equipment, and the equipment could break down.
-
-
-
-
Avoid locations near windows or with exposure to direct sunlight.
Avoid locations with drastic temperature fluctuations.
Avoid too much dust.
Avoid locations that suffer from vibration.
y Allow the air to flow freely and make sure of ventilation.
With inadequate ventilation, the unpleasant odor released by the ozone will begin to domi-
nate the atmosphere.
General Precautions 17
When using the equipment
Warning
y Do not place metallic objects or containers with liquid (flower vases, coffee cups, etc.) on or
near the equipment. And keep paper clips and staples away from the air vent. This could
cause a fire or give you an electric shock.
y If the equipment becomes excessively hot, smoke comes out of it or there is an odd smell or
noise, proceed as follows.
Turn the power OFF and remove the plug from the outlet, then contact your service repre-
sentative.
y If the equipment will not be used for more than one month, remove the plug from the outlet
for safety purposes during that time.
This could cause a fire or give you an electric shock if an insulation failure occurs.
Caution
y Do not place heavy objects (4 kg or more) on the original glass and do not press on it with
force. Breaking the glass could cause personal injury.
y Do not place heavy objects (4 kg or more) on the equipment. If the objects fall off, this could
cause injury.
y Be careful not to let your fingers be caught when closing the drawer. This could injure you.
y Do not remove or connect the plug with wet hands, as this could give you an electric shock.
y Do not touch the fuser unit or the metal area around it. Since they are very hot, you could be
burned or the shock could cause you to get your hand injured in the machine.
y Be careful not to let your fingers be caught between the equipment and the side cover. This
could injure you.
y Do not touch the photoconductive drum surface or the transfer charger. This could cause
image problems.
y Do not touch the hinge (= a connecting part) on the rear side of the Reversing Automatic
Document Feeder (optional) / Automatic Document Feeder (optional). This could catch and
injure your fingers when you open or close the Reversing Automatic Document Feeder
(optional) / Automatic Document Feeder (optional).
18 General Precautions
Other points
y Do not turn the power OFF with jammed paper left inside the equipment. This could cause
malfunctions when the main switch is turned ON next time.
y Be sure to turn the power OFF when leaving the office or if there is a power failure.
y Be careful because the paper exit area and paper just after exiting are hot.
y Do not place anything other than paper on the receiving tray. This could disturb a normal
operation and cause malfunctions.
During maintenance or inspection
Warning
y Never attempt to repair, disassemble or modify the equipment by yourself. You could cause
a fire or get an electric shock.
Always contact your service representative for maintenance or repair of the internal parts of
the equipment.
y Always keep the plug and outlet clean. Prevent them from accumulating dust and dirt. This
could cause a fire and give you an electric shock due to the heat released by electric leak-
age.
y Do not let liquids such as water and oil get into the system when cleaning the floor. This
could cause a fire and give you an electric shock.
Other points
y Do not use such solvents as thinner or alcohol when cleaning the surface of the equipment.
-
-
This could warp the shape of the surface or leave it discoloured.
When using a chemical cleaning pad to clean it, pay attention to any cautionary points.
When handling supplies
Warning
y Never attempt to incinerate toner cartridges. This could cause an explosion. Do not dispose
of used toner cartridges. Contact your service representative.
20 General Precautions
How to Use Antiskid Devices
The Paper Feed Pedestal (optional) has 4 antiskid devices and 2 fall-preventing stoppers under
its bottom. When moving this equipment, turn them in the direction of arrows (see figures below)
and raise them to unfix the equipment. After it has been moved, be sure to turn them in the
opposite direction and lower them to fix it.
Adjusters
Safety stoppers
Do not install the equipment by yourself or try to move it once it has been installed.
This could result in an injury or damage to the device. Contact your service representative if the
equipment needs to be installed or moved.
How to Use Antiskid Devices 21
Disclaimer Notice
The following notice sets out the exclusions and limitations of liability of TOSHIBA TEC CORPO-
RATION (including its employees, agents and sub-contractors) to any purchaser or user (‘User’)
of the e-STUDIO165/205, including its accessories, options and bundled software (‘Product’).
1. The exclusion and limitations of liability referred to in this notice shall be effective to the full-
est extent permissible at law. For the avoidance of doubt, nothing in this notice shall be taken
to exclude or limit TOSHIBA TEC CORPORATION’s liability for death or personal injury
caused by TOSHIBA TEC CORPORATION’s negligence or TOSHIBA TEC CORPORA-
TION’s fraudulent misrepresentation.
2. All warranties, conditions and other terms implied by law are, to the fullest extent permitted
by law, excluded and no such implied warranties are given or apply in relation to the Prod-
ucts.
3. TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense, claim or dam-
age whatsoever caused by any of the following:
(a) use or handling of the Product otherwise than in accordance with the manuals, including
but not limited to Operator’s Manual, User’s Guide, and/or incorrect or careless handling or
use of the Product;
(b) any cause which prevents the Product from operating or functioning correctly which
arises from or is attributable to either acts, omissions, events or accidents beyond the rea-
sonable control of TOSHIBA TEC CORPORATION including without limitation acts of God,
war, riot, civil commotion, malicious or deliberate damage, fire, flood, or storm, natural
calamity, earthquakes, abnormal voltage or other disasters;
(c) additions, modifications, disassembly, transportation, or repairs by any person other than
service technicians authorized by TOSHIBA TEC CORPORATION; or
(d) use of paper, supplies or parts other than those recommended by TOSHIBA TEC COR-
PORATION.
4. Subject to paragraph 1, TOSHIBA TEC CORPORATION shall not be liable to Customer for:
(a) loss of profits; loss of sales or turnover; loss of or damage to reputation; loss of produc-
tion; loss of anticipated savings; loss of goodwill or business opportunities; loss of custom-
ers; loss of, or loss of use of, any software or data; loss under or in relation to any contract;
or
(b) any special, incidental, consequential or indirect loss or damage, costs, expenses, finan-
cial loss or claims for consequential compensation;
whatsoever and howsoever caused which arise out of or in connection with the Product or
the use or handling of the Product even if TOSHIBA TEC CORPORATION is advised of the
possibility of such damages.
TOSHIBA TEC CORPORATION shall not be liable for any loss, cost, expense, claim or dam-
age caused by any inability to use (including, but not limited to failure, malfunction, hang-up,
virus infection or other problems) which arises from use of the Product with hardware, goods
or software which TOSHIBA TEC CORPORATION has not directly or indirectly supplied.
22 Disclaimer Notice
1.
PREPARATION
This chapter describes what you need to know before using this equipment, such as how to turn the power
ON or how to set copy paper.
Left side / Inner side..........................................................................................................................26
Preparation 1 - Turning Power ON.........................................................................33
Turning power ON.............................................................................................................................33
Preparation 2 - Placing Copy Paper......................................................................35
Acceptable media types....................................................................................................................35
Placing paper in the drawers of Paper Feed Pedestal (optional)......................................................41
Preparation 3 - Registering Size of Paper Placed................................................45
Registering standard size (A3, A4, A4-R, A5-R, B4).........................................................................45
Registering other standard sizes.......................................................................................................47
1
PREPARATION
Description of Each Component
Front / Right side
1
2
3
4
12
11
10
5
6
9
8
7
1. Platen Cover (optional, KA-1640PC)
Place an original on the original glass and start copying with this cover closed.
2. Reversing Automatic Document Feeder (optional, MR-3019) / Automatic Document
of sheets can be placed may vary depending on the media type of the originals.) 2-sided
originals can be scanned with the Reversing Automatic Document Feeder (MR-3019).
P.54 “Placing originals on Reversing Automatic Document Feeder (optional) / Automatic
Document Feeder (optional)”
P.174 “Paper jams within Reversing Automatic Document Feeder (optional) / Automatic
Document Feeder (optional)”
3. Operator’s Manual pocket (Back side)
Keep the Operator’s Manual in this.
5. Bypass tray
Use this to make copies on special media types such as overhead transparencies or tracing
paper.
P.59 “Using Bypass Tray”
P.177 “Paper jams on bypass tray”
6. Paper feed cover (Upper: Paper Feed Unit / Lower: Paper Feed Pedestal)
24 Description of Each Component
7. Paper size indicator
8. Paper Feed Pedestal (optional, KD-1013)
Use this to add one more drawer to the equipment. Moreover, the Drawer Module (MY-1028)
(9) can add another drawer to it. In one drawer, the maximum 550 sheets of plain paper can
be placed at once.
9. Drawer Module (optional, MY-1028)
Use this to add one more drawer to the Paper Feed Pedestal (optional, KD-1013). The max-
imum 550 sheets of plain paper can be placed at once.
10. Paper Feed Unit (optional, MY-1027)
Use this to add one more drawer to the equipment. A maximum of 250 sheets of plain paper
can be placed in one go.
11. Drawer
Maximum 250 sheets of plain paper can be placed in one go.
12. Front cover
Open this cover when you replace the toner cartridge.
P.185 “Replacing Toner Cartridge”
Description of Each Component 25
1
PREPARATION
Left side / Inner side
12
1
11
10
2
3
9
8
7
6
5
4
1. Original glass
Use this to copy three-dimensional originals, book-type originals and special paper such as
P.50 “Placing Originals”
2. Control panel
Use this to perform copying, key in the copy quantity, or set other functions.
P.29 “Control panel”
Use this when using the optional scanning and Fax functions to select destinations.
4. Toner cartridge
P.185 “Replacing Toner Cartridge”
5. Power switch
Turn the power of the equipment ON or OFF with this.
P.33 “Preparation 1 - Turning Power ON”
6. Paper exit stopper
Use this to prevent the exiting paper from falling. Open this when you make a large amount
of copies on a larger size of paper (e.g. A3, B4).
7. AC-IN terminal
Use this to connect the co-packed power cable and the equipment.
26 Description of Each Component
8. USB terminal (4-pin)
With this terminal, the equipment can be connected to your PC using a commercially avail-
able USB cable.
9. Receiving tray
10. Scanning area
The data of originals transported from the Reversing Automatic Document Feeder (optional,
MR-3019)/Automatic Document Feeder (optional, MR-2017) are scanned here.
P.198 “Daily Inspection”
11. Original scale
Use this to check the size of an original placed on the original glass.
12. Platen sheet
P.198 “Daily Inspection”
Description of Each Component 27
1
PREPARATION
Configuration of options
The options listed below are available. Contact your service technician or service representative
for the details.
Reversing Automatic Document Feeder
(MR-3019)
Platen Cover
(KA-1640PC)
Automatic Document Feeder (MR-2017)
External Keyboard
(GJ-1040)
Network Printer Kit
(GA-1190)
Scanner Upgrade Kit
(GA-1200)
Expansion Memory
(GC-1240)
Automatic Duplexing Unit
(MD-0103)
Fax Kit
(GD-1220EU)
Main body
Paper Feed Unit
(MY-1027)
Drawer Module
(MY-1028)
Paper Feed Pedestal
(KD-1013)
28 Description of Each Component
Control panel
1 2
3
4
5
6 7
8
9
10
11
12 13
25 24
23
22
21 20
1918
17 16
15 14
1. APS/AMS selecting button/lamps
Automatic paper selection (APS): The equipment detects the size of original and automat-
ically selects the same size of copy paper.
P.69 “Paper Selection”
Automatic magnification selection (AMS): Set the size of copy paper to be used in
advance. The equipment then detects the size of original and automatically selects the most
suitable reproduction ratio to the copy paper.
2. [MIXED SIZE] button/lamp
Use this to copy originals whose sizes are different.
For the details of the mixed-size copying, see the following page:
P.72 “Copying Different Sizes in One Go - MIXED-SIZE COPYING -”
3. [ENERGY SAVER] button
Use this to let the equipment enter into the energy saving mode when the equipment is not
used.
For the details of the energy saving mode, see the following page:
4. [INTERRUPT] button
Use this to interrupt the copy job in process and perform another one (= interrupt copying).
For the details of interrupt copying, see the following page:
5. [USER FUNCTIONS] button
Use this to change the equipment’s default settings.
For the details of default setting change, see the following page:
P.115 “CHANGING EQUIPMENT’S SETTINGS”
Description of Each Component 29
1
PREPARATION
6. [SETTINGS] button
Use this to confirm the copying functions currently set.
P.68 “Confirming set functions”
7. Selecting button A (Left) / B (Centre) / C (Right)
Use them to select items or operation in each menu. Items or operation corresponding to
each button appears at the lower section of the LCD screen.
e.g.) “Copy mode” main screen
READY
1
ZOOM FINISHING EDIT
A
B
C
P.32 ““Copy mode” main screen”
8. LCD screen
Use this to check each menu and error messages displayed on it.
P.32 ““Copy mode” main screen”
9. Digital keys
Use them to key in any number such as copy quantity.
10. FAX TX/RX lamp
This lamp blinks at the transmission and reception of Fax data.
11. Function switching buttons
Use them to switch functions among copying, printing, scanning and Fax.
To utilize the scanning functions, the Scanner Upgrade Kit (optional) is required.
To utilize the Fax functions, the Fax Kit (optional) is required.
12. [FUNCTION CLEAR] button/lamp
Use this to clear the set copy functions.
13. Contrast adjustment volume
Use this to adjust the brightness level of the LCD screen (8).
14. [CLEAR/STOP] button
Use this to stop the copy job in process or return the copy quantity keyed in to “1”.
15. [START] button
Use this to start copying. Copies can be made when the lamp is lit. It blinks when the equip-
ment is waiting for copying to be started.
P.55 “Making Copies”
16. Alarm lamp
This lamp blinks when an error such as paper jams or running out of toner has occurred.
P.170 “When This Message Appears”
30 Description of Each Component
17. [DATA] lamp
This lamp blinks when print data are being received.
18. [CANCEL] button
Use this to cancel the current setting and return to the previous menu.
19. [ENTER] button
Use this to determine items or operation selected in each menu.
20.
/
/
/
(UP/DOWN/LEFT/RIGHT) buttons
Use them to select items you want to set in each menu. The selected item is highlighted.
21. Original mode button/lamps
Use this button to set the image quality of copy according to that of an original.
For the details of image quality, see the following page:
P.79 “Selecting Image Mode”
22. Density adjustment buttons/lamps
Use this button to adjust the density of copy image. The [AUTO] lamp below the
(automatic copy density mode) button is lit when the density is being automatically adjusted.
For the details of density adjustment, see the following page:
P.80 “Adjusting Density Level”
23. [DRAWER] button/lamps
of the paper source currently selected is lit. The lamp blinks when the selected drawer or tray
is running out of paper.
When paper in the drawer or on the bypass tray has run out, see the following page to add
paper:
P.35 “Preparation 2 - Placing Copy Paper”
24. [COPY] button/lamps
Use this button to select the size of paper to be used. The lamp of the paper size currently
selected blinks when this size of paper is not placed in the drawer or on the bypass tray.
P.70 “Manual paper selection”
25. [ORIGINAL] button/lamps
Use this button to specify the size of an original.
P.76 “Specifying both the sizes of the original and the copy paper”
Description of Each Component 31
1
PREPARATION
“Copy mode” main screen
After the power of the equipment is turned ON and the warm-up is finished, the display below is
shown on the LCD screen. This display is called the “copy mode” main screen.
1
2
READY
100%
1
NONSORT
3
5
ZOOM FINISHING EDIT
4
This “copy mode” main screen appears by default after turning the power ON. You can display
the main screen for the Fax function or the scanning function instead of the “copy mode” main
screen by changing the default setting.
P.126 “Walkup Screen Setting”
1. Message area
This area displays the current status of this equipment or error messages.
2. Copy quantity
3. Reproduction ratio
4. Selecting button display
ZOOM: Use this to specify the reproduction ratio manually.
Custom mode: Use this to recall the copying function registered as a custom function. You
can quickly recall functions frequently used by registering it on the custom mode.
P.155 “Menu Customize”
EDIT: This area displays the copy menu. Use this to recall the desired copying function.
P.82 “Copy Menu”
5. Custom mode setting
This area displays the current setting of the function which has been registered as custom
function.
32 Description of Each Component
Preparation 1 - Turning Power ON
Turning power ON
Open the power switch cover, and then press the power switch to
“ ” (ON) side.
1
The equipment starts warming itself up. The warm-up time takes approx. 25 seconds.
When the warm-up has finished, the equipment is ready for copying. “READY” appears
on the LCD screen.
READY
1
100%
NONSORT
ZOOM FINISHING EDIT
If you place an original and press the [START] button during the warm-up, copying auto-
matically starts when the warm-up has finished (= auto job start). When the job is
reserved, “Auto Start” appears on the LCD screen.
The LCD screen below is shown if the equipment is managed under
the department code function. Key in the department code.
2
Enter DEPARTMENT CODE
1
100%
NONSORT
Key in a 5-digit department code, and then press the [ENTER] button. Then the
equipment is ready for copying.
If the department code function is enabled, press the [FUNCTION CLEAR] button after
any operation has been finished to prevent unauthorized use of the equipment.
For the details of the department code, see the following page:
P.141 “Department Code”
Turning power OFF
Open the power switch cover, and then press the power switch to “ ” (OFF) side.
Preparation 1 - Turning Power ON 33
1
PREPARATION
Saving energy when not in use - Energy saving mode -
To reduce power consumption, the equipment automatically enters into the energy saving mode
when a specified period of time has passed since its last use. You can also turn the equipment
into this mode manually.
y The period of time at which the equipment enters into this mode is set at 30 minutes at the
shipment from the factory.
y The power consumption during this mode is set at 6 W or less. (When the Network Printer Kit
is installed, or when the equipment is connected to a PC with a USB cable, the power con-
sumption during this mode is set at 39 W or less.)
To turn the equipment into the energy saving mode manually
Press the [ENERGY SAVER] button on the control panel.
The equipment is now in the energy saving mode. The display on the LCD screen goes off and
the [ENERGY SAVER] lamp is lit.
When the Network Printer Kit (optional) is installed, or when this equipment is connected to a PC
with a USB cable, “Sleep mode” appears on the LCD screen. In these cases, the [ENERGY
SAVER] lamp is not lit.
Canceling the energy saving mode
If the [ENERGY SAVER] lamp is lit, press this button.
If “Sleep mode” is displayed on the LCD screen, press any button other than the [ENERGY
SAVER] button on the control panel.
The energy saving mode can be also cancelled under the following conditions:
y When the Platen Cover (optional) or the Reversing Automatic Document Feeder / Automatic
Document Feeder (optional) is raised
y When this equipment is connected to a PC with a USB cable
y When Fax data are received
When the Network Printer Kit (optional) is installed, or when this equipment is connected to a PC
with a USB cable, the energy saving mode can be cancelled when print data are received.
34 Preparation 1 - Turning Power ON
Preparation 2 - Placing Copy Paper
Place copy paper in an appropriate paper source before you start copying.
Acceptable media types
Acceptable media types differ depending on its paper source. See the table below for the details.
Maximumsheet
Feeder
Media type
Paper size
*1
capacity
Drawers of Plain paper
A/B format:
250 sheets
(64 - 80 g/m2)
(64 g/m2)
250 sheets
(80 g/m2)
the equip-
ment and
PaperFeed
Unit
A3, A4, A4-R, B4, B5, B5-R, FOLIO
LT format:
LD, LG, LT, LT-R, COMP, 13"LG
(optional)
Drawers of Plain paper
A/B format:
550 sheets
(64 - 80 g/m2)
(64 g/m2)
550 sheets
(80 g/m2)
the Paper
Feed Ped-
estal
(optional)
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO
LT format:
LD, LG, LT, LT-R, ST-R, COMP, 13"LG
Bypass tray Plain paper
A/B format:
100 sheets
64 - 80 g/m2)*2
(64 g/m2)
100 sheets
(80 g/m2)
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO
LT format:
LD, LG, LT, LT-R, ST-R, COMP, 13"LG
THICK PAPER 1
(81 - 105 g/m2)*3
THICK PAPER 2
(106 - 163 g/m2)*3
Tracing paper
1 sheet
(81 - 105 g/m2)
1 sheet
(106 - 163 g/m2)
1 sheet
Sticker labels*3
Transparencies*3, *4
1 sheet
1 sheet
A4 only
*1 “Maximum sheet capacity” refers to the maximum number of sheets when TOSHIBA-recommended
paper is used. See the following page for the TOSHIBA-recommended paper:
P.36 “Recommended paper”
*2 The paper of 50 to 63 g/m2 can be used if it is set on the bypass tray one by one.
*3 Automatic duplex copying is not available.
*4 Be sure to use the overhead transparencies that TOSHIBA recommends. When transparencies other
than the TOSHIBA-recommended ones are used, this could cause an equipment malfunction.
y You cannot mix various paper sizes in one drawer.
y “LT format” is the standard size for only use in North America.
Abbreviations for LT format sizes:
LT: Letter, LD: Ledger, LG: Legal, ST: Statement, COMP: Computer
Preparation 2 - Placing Copy Paper 35
1
PREPARATION
Recommended paper
To ensure the best copy performance, TOSHIBA recommends the paper types listed below. If
you want to use paper other than that we recommend, contact your service technician.
Media type
Product name
80 g/m2
Plain paper
TGIS Paper/Neusiedler
90 g/m2
THICK PAPER 1
THICK PAPER 2
Colour Copy/Neusiedler
Colour Copy/Neusiedler
Colour Copy/Neusiedler
Colour Copy/Neusiedler
Tracing paper/Ostrich International
100 g/m2
120 g/m2
160 g/m2
75 g/m2 only
Tracing paper
Sticker labels
Transparencies *1
3478/Zweckform-Avery
PP2500/3M
*1 Be sure to use the overhead transparencies that TOSHIBA recommends. When transparencies other
than the TOSHIBA-recommended ones are used, this could cause an equipment malfunction.
Paper types not acceptable
Do not use the types of paper listed below since they may cause paper jams.
y Damp paper
y Creased paper
y Wrinkled paper or paper prone to be curled
y Paper whose surface is extremely smooth or rough
Do not use the types of paper listed below since they may cause an equipment malfunction.
y Paper whose surface is specially treated
y Paper once printed with other copiers or printers
Storing paper
Observe the following cautions when storing copy paper:
y Wrap copy paper in its wrapping paper to prevent it from gathering dust.
y Do not expose copy paper to direct sunlight.
y Store copy paper in a damp-free place.
y Store copy paper on a flat surface to prevent it from being creased or bent.
36 Preparation 2 - Placing Copy Paper
Placing paper in drawers
Follow the procedure below to place copy paper in the drawer.
For the acceptable paper, see the following page:
P.35 “Acceptable media types”
Turn the power of the equipment ON.
1
Pull out the drawer carefully.
2
Pull out the drawer until it comes to a stop.
Press down the paper plate.
3
Press it down until you hear a click sound and it is no longer lifted up.
Preparation 2 - Placing Copy Paper 37
1
PREPARATION
Pull out the trailing guide (A), and then reinstall the guide at the
position of the desired paper size.
4
A
The paper size is indicated on the bottom inner surface of the drawer.
While pushing the green knob of the side guides fully, widen the
gap between them.
5
Widen the gap with both hands.
38 Preparation 2 - Placing Copy Paper
Place paper in the drawer.
6
2
y The maximum number of sheets can be placed in one go is 250 (80 g/m ). Be sure
that the stack height of paper is not higher than the line indicated at the inner side of
the guide.
P.35 “Acceptable media types”
y Fan the paper well before placing it in the drawer, otherwise multiple feeding could
occur.
y Place the paper face up. You may tell its “face” by the note on its wrapping paper.
Adjust the side guides to the desired paper size.
7
Be sure that a gap of approx. 0.5 mm (less than 1.0 mm in total) is left between the paper
and each side guide (shown as “A” in the picture). If the gap is inappropriate, this could
cause a paper misfeed.
A
Preparation 2 - Placing Copy Paper 39
1
PREPARATION
Be sure that the stack of paper fits completely under the latches of
the side guides.
8
Change the paper size indicator to match the size of paper placed.
9
Push the drawer straight into the equipment slowly until it comes to
a stop.
10
Do not let your fingers be caught when closing the drawer.
This could cause injury.
Register the paper size into the equipment.
When you place paper, register the size of the paper into the equipment. Be sure that the size is
registered correctly, or it could cause a paper jam.
For the registration of paper size, see the following page:
P.45 “Preparation 3 - Registering Size of Paper Placed”
Be sure to register the paper size when you have changed the paper size in the drawer, as well
as when you place paper in the corresponding drawer for the first time.
40 Preparation 2 - Placing Copy Paper
Follow the procedure below to place copy paper in the drawers of the Paper Feed Pedestal
(optional).
For the acceptable paper, see the following page:
P.35 “Acceptable media types”
Pull out the drawer carefully.
1
Pull out the drawer until it comes to a stop.
Pull out the trailing guide while pushing its lower part to the direc-
tion of the arrow. Then reinstall the guide at the position of the
desired paper size.
2
The paper size is indicated on the bottom inner surface of the drawer.
Preparation 2 - Placing Copy Paper 41
1
PREPARATION
Push the right side of the side guide lock to unlock it.
3
While pushing the green knob of the side guides, adjust the side
guides at the position of the desired paper size.
4
Adjust the side guides with both hands.
42 Preparation 2 - Placing Copy Paper
Place paper in the drawer.
5
2
y The maximum number of sheets can be placed in one go is 550 (80 g/m ). Be sure
that the stack height of paper is not higher than the line indicated at the inner side of
the guide.
P.35 “Acceptable media types”
y Fan the paper well before placing it in the drawer, otherwise multiple feeding could
occur.
y Place the paper face up. You may tell its “face” by the note on its wrapping paper.
Adjust the side guides.
6
7
Be sure that a gap of approx. 0.5 mm (less than 1.0 mm in total) is left between the paper
and each side guide (shown as “A” in the picture). If the gap is inappropriate, this could
cause a paper misfeed.
A
Push the left side of the side guide lock to lock it.
Preparation 2 - Placing Copy Paper 43
1
PREPARATION
Change the paper size indicator to match the size of paper placed.
8
Push the drawer straight until it comes to a stop.
9
Do not let your fingers be caught when closing the drawer.
This could cause injury.
Register the paper size into the equipment.
When you place paper, register the size of the paper into the equipment. Be sure that the size is
registered correctly, or it could cause a paper jam.
For the registration of paper size, see the following page:
P.45 “Preparation 3 - Registering Size of Paper Placed”
Be sure to register the paper size when you have changed the paper size in the drawer, as well
as when you place paper in the corresponding drawer for the first time.
44 Preparation 2 - Placing Copy Paper
Preparation 3 - Registering Size of Paper Placed
When you place paper in a drawer for the first time or when you place paper whose size is differ-
ent from that of the paper which has been placed in the drawer, the new paper size needs to be
registered into the equipment.
Registration of standard sizes (A3, A4, A4-R, A5-R, B4) differs from that of standard sizes other
The paper size can be registered on the LCD screen by checking menus.
P.124 “Paper Size Setting”
Registering standard size (A3, A4, A4-R, A5-R, B4)
In this section, A4 size is registered in the drawer of the equipment as an example.
Press and hold the [COPY] and [DRAWER] buttons simultaneously
for more than two seconds.
1
The LCD screen shows as follows:
Select paper size
1
100%
NONSORT
ZOOM FINISHING EDIT
Press the [DRAWER] button several times until the lamp of the
drawer in which you placed paper is lit.
2
Preparation 3 - Registering Size of Paper Placed 45
1
PREPARATION
Press the [COPY] button several times until the lamp of the paper
size you placed in the drawer is lit.
3
If the [CANCEL] button is pressed at this step, the size is not registered and the
equipment will return to its normal status.
Press the [ENTER] button.
The paper size has been registered.
4
46 Preparation 3 - Registering Size of Paper Placed
Registering other standard sizes
When standard size paper other than A3, A4, A4-R, A5-R or B4 is placed, register this size as
“OTHER” size.
In this section, LT size is registered in the drawer of the equipment as an example.
Press and hold the [COPY] and [DRAWER] buttons simultaneously
for more than two seconds.
1
The LCD screen shows as follows:
Select paper size
1
100%
NONSORT
Press the [DRAWER] button several times until the lamp of the
drawer in which you placed paper is lit.
2
Preparation 3 - Registering Size of Paper Placed 47
1
PREPARATION
Press the [COPY] button several times until the [OTHER] lamp is lit.
3
Press the selecting button B or C to select the paper size placed in
the drawer.
4
e.g.) Placing LT size
Select paper size LG
LT
LT-R
Press the [ENTER] button.
The LCD screen shows as follows:
5
6
Select paper size
1
100%
NONSORT
Press the [ENTER] button.
The paper size has been registered as “OTHER” size and the equipment will return to its
normal status.
48 Preparation 3 - Registering Size of Paper Placed
2.
HOW TO MAKE COPIES
This chapter describes basic copy operations.
Acceptable originals..........................................................................................................................50
Placing originals on the original glass...............................................................................................51
Placing booklet-type originals such as books or catalogues.............................................................52
Interrupting copying and making another copy - Interrupt copy -......................................................58
Using Bypass Tray..................................................................................................59
Preparation - Registering paper size placed on bypass tray.............................................................60
Bypass copying on standard size paper............................................................................................64
2
HOW TO MAKE COPIES
Placing Originals
Acceptable originals
Booklets, three-dimensional objects and some types of special media can be placed on the orig-
inal glass, as well as plain paper. When the Reversing Automatic Document Feeder (optional) /
Automatic Document Feeder (optional) is used, a stack of plain paper originals can be automat-
ically scanned one by one.
Acceptable sizes for auto-
Type of origi-
nals
Maximum
size
Setting position
Remarks
*1
matic size detection
*3
Original glass
Plain paper
297 mm x 432 A3, A4, A4-R, A5-R, B4, B5,
Special media
mm
B5-R
types*2
Booklets
3-dimensional
objects
*4, *5, *6, *7
Reversing Auto-
matic Document
Feeder (optional) /
Automatic Docu-
ment Feeder
Plain paper
A3, A4, A4-R, A5-R, B4, B5,
B5-R, FOLIO
(optional)
*1 The automatic size detection function is not enabled for LT format.
*2 “Special media types” refers to special paper which is not acceptable for the Reversing Automatic Docu-
ment Feeder (optional) / Automatic Document Feeder (optional), such as overhead transparencies or
tracing paper.
*3 Do not place heavy objects (4 kg or more) and do not press on it with force.
*4 The size of FOLIO originals can be detected automatically only when they are placed on the Reversing
Automatic Document Feeder (optional).
*5 Their paper weight should be between 50 g/m2 and 127 g/m2 (in both cases of 1-sided and 2-sided).
*6 Some media types may not be used.
*7 A5 size originals must be placed in a landscape direction.
Maximum number of originals scanned in one go
In terms of A4 originals, the maximum number of sheets which can be scanned in one go is 250.
When the number of sheets scanned has exceeded 250 during one copy job in process, scan-
ning stops and “Count over” appears on the LCD screen.
Count over
Cancel job
Print
Select “Print” on the LCD screen to copy the data scanned so far. Select “Cancel job” to delete
all the data scanned so far.
50 Placing Originals
When the built-in memory has become full during scanning
When the built-in memory in the equipment has become full during the scanning of the copy job,
scanning stops even if the number of sheets scanned so far has not exceeded the maximum
value. “Memory is full” appears on the LCD screen.
Memory is full
Cancel job
Print
Select “Print” on the LCD screen to copy the data scanned so far. Select “Cancel job” to delete
all the data scanned so far.
Placing originals on the original glass
Plain paper or some special media types which are not acceptable for the Reversing Automatic
Document Feeder (optional) / Automatic Document Feeder (optional), such as overhead trans-
parencies or tracing paper, should be placed on the original glass.
Do not place heavy objects (4 kg or more) and do not press on it with force.
Breaking the glass could injure you.
Raise the Platen Cover (optional) or the Reversing Automatic Docu-
ment Feeder (optional) / Automatic Document Feeder (optional).
1
Raise the Platen Cover (optional) or the Reversing Automatic Document Feeder
(optional) / Automatic Document Feeder (optional) 60 degrees or more from the equip-
ment to detect the original size.
Place the original face down on the original glass and align it
against the left rear corner of the glass.
2
Placing Originals 51
2
HOW TO MAKE COPIES
When copying highly transparent originals
When copying highly transparent originals such as overhead transparencies or tracing
paper, place a blank sheet of paper (A), the same size as the original or larger, over the
original (B).
A
B
Lower the Platen Cover (optional) or the Reversing Automatic Doc-
ument Feeder (optional) / Automatic Document Feeder (optional)
carefully.
3
Placing booklet-type originals such as books or catalogues
Place a book-type original on the original glass.
Do not place heavy objects (4 kg or more) and do not press on it with force.
Breaking the glass could injure you.
Raise the Platen Cover (optional) or the Reversing Automatic Docu-
ment Feeder (optional) / Automatic Document Feeder (optional).
1
Open the desired page of the original and place it face down.
Align it against the left rear corner of the glass.
2
52 Placing Originals
Lower the Platen Cover (optional) or the Reversing Automatic Doc-
ument Feeder (optional) / Automatic Document Feeder (optional)
carefully.
3
y Do not try to lower the Platen Cover (optional) or the Reversing Automatic Document
Feeder (optional) / Automatic Document Feeder (optional) forcibly when the original
is very thick. There will be no problem in copying even if they are not fully lowered.
y Do not look fully at the original glass since intensive light may leak out during copy-
ing.
Using Reversing Automatic Document Feeder (optional) / Automatic
Document Feeder (optional)
When a stack of originals are placed on the Reversing Automatic Document Feeder (optional) /
Automatic Document Feeder (optional), the originals are automatically scanned one by one. The
*1
following types of originals are available
:
Maximum number of
sheets acceptable
Media types
Maximum size
Paper weight
50 - 127 g/m2
Plain paper
297 mm x 432 mm 100 sheets
(or stack height 16 mm)
*1 To scan 2-sided originals, the Reversing Automatic Document Feeder (optional) is required.
y Some media types may not be used.
y The maximum number of sheets acceptable varies depending on the media types of the
originals.
y A5 size originals must be placed in a landscape direction.
y Sizes which the Reversing Automatic Document Feeder (optional) / Automatic Document
Feeder (optional) can detect automatically are A3, A4, A4-R, A5-R, B4, B5, B5-R and
FOLIO. (The size of FOLIO originals can be detected automatically only when they are
placed on the Reversing Automatic Document Feeder (optional).)
Precautions for Reversing Automatic Document Feeder
(optional) / Automatic Document Feeder (optional)
Do not use the following types of original since such types may cause a paper jam or damage to
the equipment:
y Extremely wrinkled, folded or curled ones
y Ones with carbon paper
y Taped, pasted or cut-out ones
y Clipped or stapled ones
y Ones with holes or tears
y Damp ones
y Overhead transparencies or tracing paper
y Coating paper (e.g. coated with wax)
The following types of originals are usable but need extra care:
y Ones which cannot be slid with fingers or whose surface is specially treated (they may not be
separated from each other at feeding)
y Folded or curled ones (should be smoothed out before being used)
Placing Originals 53
2
HOW TO MAKE COPIES
When black streaks appear on the copied image
If the scanning area or the guide area is dirty, image problems such as black streaks on the cop-
ied image may occur. Weekly cleaning of these areas is recommended.
P.198 “Daily Inspection”
Placing originals on Reversing Automatic Document Feeder (optional)
/ Automatic Document Feeder (optional)
Align all the originals.
1
Place them face up and align the side guides to the original length.
2
y The top sheet of the originals will be scanned first.
2
y The total sheets of originals placed must not exceed 100 (50 to 80 g/m ) or the stack
height of the originals must not exceed 16 mm regardless of their sizes.
When placing a large amount of originals with a long width
Pull out the original stopper so that the exiting originals will not fall. When replacing this
stopper, lift it slightly and push it in.
54 Placing Originals
Making Copies
Various copying functions are available. See the following page for the details:
Check if paper is placed in the drawer.
For the acceptable types and sizes of paper, see the following pages:
1
P.35 “Acceptable media types”
P.37 “Placing paper in drawers”
2
P.50 “Acceptable originals”
P.54 “Placing originals on Reversing Automatic Document Feeder (optional) /
Automatic Document Feeder (optional)”
P.51 “Placing originals on the original glass”
P.52 “Placing booklet-type originals such as books or catalogues”
Key in the desired number of copies (= copy quantity) when you
copy more than one set.
3
e.g.) 5 sets
READY
5
100%
NONSORT
ZOOM FINISHING EDIT
Select the copy modes as required.
4
P.67 “COPYING FUNCTIONS”
P.81 “ADVANCED COPYING FUNCTIONS”
Some functions may not be used together with other functions. For the details, see the
following page.
P.209 “Copying Function Combination Matrix”
Making Copies 55
2
HOW TO MAKE COPIES
Press the [START] button.
Copying starts. The paper will exit with its copied side down.
5
The paper exit area and exiting paper are hot immediately after the exit. Handle them
with care.
When “Next original?” appears
Next original?
YES
NO
This message appears when “SORT” is selected for the exiting method while an original is being
placed on the original glass, or when 2-sided copying is being performed.
Place the next original on the original glass, and then press the [START] button. The data of the
next original will be scanned. When all the originals have been scanned, select “NO”, and then
press the [START] or [ENTER] button. Copying starts.
When the number of sheets exiting has exceeded 250
To prevent exiting paper from falling off the receiving tray, the equipment causes copying to
pause when approx. 250 sheets of paper have been continuously exited. The LCD screen
shows as follows:
Clear paper output tray:
PRESS START KEY.
Remove the paper from the receiving tray, and then press the [START] button. Copying
resumes.
Press the [CLEAR/STOP] button to end the copy job. “Memory clear?” appears on the LCD
screen. Select “YES”, and then press the [START] or [ENTER] button.
When the paper has run out
When the paper in the drawer has run out during copying, the copying stops and the LCD screen
shows as follows:
e.g.) Paper in the drawer of the equipment has run out
DRAWER1 empty
Open DRAWER1
Load paper
Close DRAWER1
The [DRAWER] lamp corresponding to the one whose paper has run out blinks.
Add paper to the drawer and press the [START] button. Copying then resumes.
56 Making Copies
Stopping/Resuming copying
Press the [CLEAR/STOP] button to stop scanning or copying.
Press the [CLEAR/STOP] button during scanning or copying.
1
Scanning or copying stops, and the LCD screen shows as follows:
Memory clear?
YES
NO
Or
Cancel job?
YES
NO
Press the selecting button C and select “YES” to end the copy job. Then press the
[START] or [ENTER] button.
Press the selecting button C and select “NO” to resume the copy
job. Then press the [START] or [ENTER] button.
2
Making Copies 57
2
HOW TO MAKE COPIES
Interrupting copying and making another copy - Interrupt copy -
You can interrupt scanning or copying of one job and make another copy job (= interrupt copy-
ing). The copy quantity or functions applied to the interrupted job are stored in the memory of
this equipment, so that you will not need to set them again when the interrupted job resumes.
Press the [INTERRUPT] button.
The [INTERRUPT] lamp blinks, and the lamp will be fully lit after a while.
1
The LCD screen shows as follows:
Job interrupted
1
100%
NONSORT
ZOOM FINISHING EDIT
When the [INTERRUPT] button is pressed during scanning, the [INTERRUPT] lamp
blinks, and then the lamp will be fully lit after the scanning has finished.
Replace the original with a new one.
2
3
Select the copy modes as required, and then press the [START]
button.
Interrupt copying starts.
After you have finished interrupt copying, press the [INTERRUPT]
button.
4
5
The copying status returns to the one before the interruption.
Press the [START] button.
The job interrupted will resume.
58 Making Copies
Using Bypass Tray
Place paper on the bypass tray when you use the following media types as copy paper:
2
y Thick paper (81 to 163 g/m )
y Special media types such as tracing paper, sticker labels or overhead transparencies
y Standard size paper which cannot be placed in the drawers of the equipment and Paper
Feed Unit (optional) (e.g. A5-R)
Using the bypass tray is recommended also for copying on standard-size paper other than those
placed in the drawers. The following sizes are available for bypass copying:
Maximum sheet
Media type
Paper size
*1
capacity
100 sheets (64 g/m2)
100 sheets (80 g/m2)
1 sheet
Plain paper
(64 - 80 g/m2)*2
A/B format:
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO
LT format:
THICK PAPER 1
LD, LG, LT, LT-R, ST-R, COMP, 13"LG
(81 - 105 g/m2)*3
THICK PAPER 2
(106 - 163 g/m2)*3
Tracing paper
(81 - 105 g/m2)
1 sheet
(106 - 163 g/m2)
1 sheet
(75 g/m2)*3
Sticker labels*3
Transparencies*3, *4
1 sheet
1 sheet
A4 only
*1 “Maximum sheet capacity” refers to the maximum number of sheets when TOSHIBA-recommended
paper is used. See the following page for the TOSHIBA-recommended paper:
P.36 “Recommended paper”
*2 The paper of 50 to 63 g/m2 can be used if it is set on the bypass tray one by one.
*3 Automatic duplex copying is not available.
*4 Be sure to use the overhead transparencies that TOSHIBA recommends. When transparencies other
than the TOSHIBA-recommended ones are used, this could cause an equipment malfunction.
Using Bypass Tray 59
2
HOW TO MAKE COPIES
Preparation - Registering paper size placed on bypass tray
Register the size of the paper into the equipment in advance.
The registration procedure for other paper sizes is different from the standard sizes (A3, A4, A4-
R, A5-R or B4).
The paper size can be registered on the LCD screen by checking menus.
P.124 “Paper Size Setting”
Registering standard size (A3, A4, A4-R, A5-R, B4)
In this section, the registration procedure is described with A4 size paper placed on the bypass
tray as an example.
Press and hold the [COPY] and [DRAWER] buttons simultaneously
for more than two seconds.
1
The LCD screen shows as follows:
Select paper size
1
100%
NONSORT
60 Using Bypass Tray
Press the [DRAWER] button several times until the lamp of the
bypass tray is lit.
2
3
Press the [COPY] button several times until the lamp of the paper
size you placed on the bypass tray is lit.
If the [CANCEL] button is pressed at this step, the size is not registered and the
equipment will return to its normal status.
Press the [ENTER] button.
The paper size has been registered.
4
Using Bypass Tray 61
2
HOW TO MAKE COPIES
Registering other standard sizes
When standard size paper other than A3, A4, A4-R, A5-R or B4 is placed, register this size as
“OTHER” size.
In this section, the registration procedure is described with LT size paper placed on the bypass
tray as an example.
Press and hold the [COPY] and [DRAWER] buttons simultaneously
for more than two seconds.
1
The LCD screen shows as follows:
Select paper size
1
100%
NONSORT
Press the [DRAWER] button several times until the lamp of the
bypass tray is lit.
2
62 Using Bypass Tray
Press the [COPY] button several times until the [OTHER] lamp is lit.
3
Press the selecting button B or C to select the paper size placed in
the drawer.
4
5
e.g.) Placing LT size
Select paper size LG
LT
LT-R
If the [CANCEL] button is pressed at this step, the size is not registered and the
equipment will return to its normal status.
Press the [ENTER] button.
The paper size has been registered as “OTHER” size.
Using Bypass Tray 63
2
HOW TO MAKE COPIES
Bypass copying on standard size paper
Standard size paper can be used for bypass copying. In this section, the procedure is described
Register the size of the paper into the equipment in advance.
P.60 “Preparation - Registering paper size placed on bypass tray”
Place paper straight on the bypass tray face down. Then align the
side guides to the paper length while holding (A).
1
A
y Be sure that the stack height of paper does not exceed the indicators of the side
guides.
y Fan the stack of paper well before placing it on the bypass tray.
y Do not push the paper forcibly into the entrance of the bypass feeder. This could
cause a paper misfeed.
When you place paper of a larger size, pull out the paper holder before you start bypass
copying.
64 Using Bypass Tray
Check if the lamp of the paper size placed on bypass tray is lit. If
not, press the [COPY] button several times until the lamp of the
desired paper size is lit.
2
The LCD screen shows as follows:
Ready for bypass
1
100%
SORT
ZOOM FINISHING EDIT
Select the media type most suited to the paper placed in the drawer.
(1) Press the selecting button C once.
(2) Press the selecting button A three times to select “PAPER TYPE”, and then press the
[ENTER] button.
3
Paper type setting menu appears.
PAPER TYPE THICK PAPER1
THICK PAPER2
TRANSPARENCY
(3) Press the selecting button C for several times until you select the desired media type,
and then press the [ENTER] button.
You can select the media type from the following three:
2
THICK PAPER 1: Thick paper (81 to 105 g/m )
2
THICK PAPER 2: Thick paper (106 to 163 g/m ), sticker labels
TRANSPARENCY: Overhead transparencies
2
y You do not need to select the media type when you use plain paper (64 to 80 g/m ) or
tracing paper. When the media type is already set at either of them, select “OFF”.
y If you select a different media type from the one you placed on the bypass tray, this
could cause a paper jam or the quality of the copied image could be lowered.
Place the original.
4
Using Bypass Tray 65
2
HOW TO MAKE COPIES
Select the other copy modes as required, and then press the
[START] button.
5
Copying starts.
When you make copies on overhead transparencies using the bypass tray, pick up the
transparencies which have exited onto the receiving tray one by one. If the transparen-
cies pile up, they may become curled and not be good for projection.
y When the paper on the bypass tray has run out during copying, copying continues
with the paper of the same size in the drawer as the one on the bypass tray. (If the
size of the paper on the bypass tray has not been registered in advance, however,
copying stops. In this case, add paper to the bypass tray and press the [START] but-
ton to resume copying.)
y When bypass copying has finished, the [FUNCTION CLEAR] lamp blinks. Press the
[FUNCTION CLEAR] button so that the paper size setting for the bypass tray will be
cleared. Press the [FUNCTION CLEAR] button again so that bypass copying will be
switched to copying with drawer feeding.
66 Using Bypass Tray
3.
COPYING FUNCTIONS
This chapter describes various functions related to copy operations, such as how to make enlargement or
reduction copies, or how to adjust the quality of copy images.
Paper Selection.......................................................................................................69
Manual paper selection.....................................................................................................................70
Zooming In/Out Copy Image..................................................................................74
Specifying both the sizes of the original and the copy paper ............................................................76
Specifying reproduction ratio manually .............................................................................................77
Selecting Image Mode ............................................................................................79
Adjusting Density Level .........................................................................................80
3
COPYING FUNCTIONS
Before Making Copies
Default settings
Initial settings established when the equipment is powered on before any of the user functions
are changed are called default settings. Each setting returns to its default when the power is
turned ON, when the energy saving mode is cancelled, and when the [FUNCTION CLEAR] but-
ton is pressed.
The default settings of the basic copying functions at the time of the installation are shown
below.
Item
Copy quantity
Paper selection
Contents
Default setting at installation
1 - 999
1
Automatic paper selection (APS), Man- Automatic paper selection (APS)
ual paper selection
Reproduction ratio
25 - 200%
100%
Density adjustment
Automatic copy density mode, Manual Automatic copy density mode
copy density mode
The default settings above can be changed. For the details, see the following page:
P.115 “CHANGING EQUIPMENT’S SETTINGS”
Confirming set functions
Press the [SETTINGS] button to confirm the set functions.
The current settings and functions set appear on the LCD screen.
NONSORT
2IN1 1>1 SIMPLEX
Press the selecting button B or C to display all the settings so that the display will be switched to
the next one. After you finished the confirmation, press the [SETTINGS] button again.
68 Before Making Copies
Paper Selection
You can select the size of copy paper in two ways; one is automatic paper selection in which the
equipment automatically selects copy paper of the same size as the original, and the other is
manual paper selection in which you can select the desired paper size manually.
Automatic paper selection (APS):
The equipment detects the size of the original placed and automatically selects copy paper of
the same size as the original.
The following sizes of originals are available:
A3, A4, A4-R, A5-R, B4, B5, B5-R and FOLIO (The size of FOLIO originals can be detected
automatically only when they are placed on the Reversing Automatic Document Feeder
(optional).)
Manual paper selection:
You can select the desired size of copy paper manually. This function can be used in a case the
APS cannot be used, such as when originals are non-standard sizes or overhead transparen-
cies.
Automatic paper selection (APS)
When you place a standard size original, the equipment detects its size and automatically
selects copy paper of the same size as the original.
The following sizes of originals are available:
A3, A4, A4-R, A5-R, B4, B5, B5-R and FOLIO (The size of FOLIO originals can be detected
automatically only when they are placed on the Reversing Automatic Document Feeder
(optional).)
manual paper selection for the following originals:
y Highly transparent ones (e.g. overhead transparencies, tracing paper)
y Wholly dark ones or ones with dark borders
y Non-standard size ones (e.g. newspapers, magazines)
P.70 “Manual paper selection”
Place paper in the drawer.
1
Register the size of the paper into the equipment in advance.
P.45 “Preparation 3 - Registering Size of Paper Placed”
Place the original.
2
Paper Selection 69
3
COPYING FUNCTIONS
Press the APS/AMS selecting button and select APS. (The APS
lamp is lit.)
3
y The default setting at the installation is APS.
y If the direction of paper in the drawer differs from that of originals, the image of the
original can be copied being rotated by 90 degrees, as long as their sizes are the
same (B5 and A4 only).
Select the other copy modes as required, and then press the
[START] button.
4
Manual paper selection
Select the paper size with this method when you use the following originals whose sizes may not
be detected correctly with automatic paper selection:
y Highly transparent ones (e.g. overhead transparencies, tracing paper)
y Wholly dark ones or ones with dark borders
y Non-standard size (e.g. newspapers, magazines)
In this method, if the desired size of copy paper is not placed in the drawer, replace the paper
already placed in the drawer with the desired one, or place the desired size of paper on the
bypass tray.
P.37 “Placing paper in drawers”
P.59 “Using Bypass Tray”
Place paper in the drawer.
1
Place the original.
2
70 Paper Selection
Press the [DRAWER] button several times until the lamp of the
desired drawer is lit.
3
4
e.g.) Selecting the drawer of the equipment
Select the other copy modes as required, and then press the
[START] button.
Paper Selection 71
3
COPYING FUNCTIONS
Copying Different Sizes in One Go - MIXED-SIZE COPYING -
When different sizes of originals are mixed and placed on the Reversing Automatic Document
Feeder (optional), some combinations of sizes can be copied in one go. The combination of A3
and A4, B4 and B5, or A4-R and FOLIO is available.
Place paper in the drawer.
1
Bypass copying is disabled. Place paper in the drawer.
Place originals on the Reversing Automatic Document Feeder
(optional).
2
Press the [MIXED SIZE] button.
The mixed-size copying mode is set and the [MIXED SIZE] lamp is lit.
The equipment is switched to the automatic paper selection mode and the [APS] lamp is
lit. When copying in the automatic paper selection mode, step 4 is not necessary. In this
case, proceed to step 5.
3
In the automatic paper selection mode, a copy is made on copy paper of the same size
as the original. Place paper whose sizes are the same as those of the originals in the cor-
responding drawers in advance.
72 Copying Different Sizes in One Go - MIXED-SIZE COPYING -
If you want to copy all the originals on the same size paper, press
the [DRAWER] button to select the drawer.
4
e.g.) Selecting the drawer of the equipment
When the mixed-size copying function is used, copy paper larger than the set original
cannot be used for copying. Use paper of the same size as the original or smaller. For
example, when mixed originals of A4 and A3 sizes are set, select the A4 size paper or
smaller.
Select the other copy modes as required, and then press the
[START] button.
5
Copying starts.
When “Change direction ORG” appears
The originals are not placed in a correct direction. Place them in a correct direction, and
then press the [ENTER] button. Then press the [START] button to resume copying.
When the copying has finished, press the [FUNCTION CLEAR] button.
Copying Different Sizes in One Go - MIXED-SIZE COPYING - 73
3
COPYING FUNCTIONS
Zooming In/Out Copy Image
You can set the reproduction ratio of the copy image in the following three ways:
Automatic magnification selection (AMS):
Specify the size of the copy paper in advance. As the original is placed, the equipment then
detects the size of the original and sets the reproduction ratio most suited to the size of copy
paper automatically.
The following sizes of originals are available:
A3, A4, A4-R, A5-R, B4, B5, B5-R and FOLIO (The size of FOLIO originals can be detected
automatically only when they are placed on the Reversing Automatic Document Feeder
(optional).)
Specifying both the sizes of the original and the copy paper:
When you specify the sizes of both the original and the copy paper, the equipment automatically
sets the reproduction ratio most suited to both of these sizes. This function can be used in case
the AMS cannot be used, such as when originals are overhead transparencies.
Specifying reproduction ratio manually:
Specify the reproduction ratio manually from 25% to 200%.
The reproduction ratio can be set in the horizontal and vertical direction separately. In this case,
select XY zoom function in the copy menu.
P.109 “Changing Sizes in Horizontal and Vertical Directions - XY ZOOM -”
Automatic magnification selection (AMS)
Specify the copy paper size to be used in advance. The equipment then detects the size of the
original and automatically sets the most suitable reproduction ratio for the size of copy paper, as
the original is placed.
The following sizes of originals are available:
A3, A4, A4-R, A5-R, B4, B5, B5-R and FOLIO (The size of FOLIO originals can be detected
automatically only when they are placed on the Reversing Automatic Document Feeder
(optional).)
Automatic magnification selection (AMS) may not work correctly for the size of originals listed
below. Use other methods to set the reproduction ratio for the following originals:
y Highly transparent ones (e.g. overhead transparencies, tracing paper)
y Wholly dark ones or ones with dark borders
y Non-standard size (e.g. newspapers, magazines)
74 Zooming In/Out Copy Image
Place paper in the drawer.
1
2
Press the [COPY] button several times until the lamp of the desired
paper size is lit.
e.g.) Selecting A4 size
You can select the desired paper size with the [DRAWER] button in the same procedure.
Press the APS/AMS selecting button until the AMS lamp is lit.
3
Place the original.
The equipment detects the size of the original, and then the most suitable reproduction
ratio to the copy paper size is set.
4
5
Select the other copy modes as required, and then press the
[START] button.
When “Change direction ORG” appears
The direction of the original placed is not correct. Press the [FUNCTION CLEAR] button to exit
the original. Then rotate the original by 90 degrees to place it in the correct direction.
Zooming In/Out Copy Image 75
3
COPYING FUNCTIONS
Specifying both the sizes of the original and the copy paper
Place paper in the drawer.
1
Place the original.
2
Press the [ORIGINAL] button several times until the lamp of the
desired original size is lit.
3
e.g.) Selecting B4 for the original
Press the [COPY] button several times until the lamp of the desired
paper size is lit.
4
e.g.) Selecting A4 for copy paper
y You can select the desired paper size with the [DRAWER] button in the same proce-
dure.
y When standard size paper other than A3, A4, A4-R, A5-R or B4 is placed, register
this size as “OTHER” size in advance.
P.47 “Registering other standard sizes”
The most appropriate reproduction ratio for both the sizes of the original and the copy
paper is set.
Select the other copy modes as required, and then press the
[START] button.
5
76 Zooming In/Out Copy Image
Specifying reproduction ratio manually
Place paper in the drawer.
1
Place the original.
2
Press the selecting button A.
3
The LCD screen shows as follows:
ZOOM
100%
25% ---- 200%
100%
-
+
Press the selecting button B (–) or C (+) to set the desired reproduc-
tion ratio.
One press of each button increases or decreases the reproduction ratio by 1%. When
you keep pressing either of them, the reproduction ratio also keeps changing. The
reproduction ratio can be set from 25% to 200%.
4
Press the selecting button A to return it to 100%.
Press the [ENTER] button.
The reproduction ratio is set.
5
6
Press the [COPY] button several times until the lamp of the desired
paper size is lit.
e.g.) Selecting A4 for copy paper
y You can select the desired paper size with the [DRAWER] button in the same proce-
dure.
y When standard size paper other than A3, A4, A4-R, A5-R or B4 is placed, register
this size as “OTHER” size in advance.
P.47 “Registering other standard sizes”
Zooming In/Out Copy Image 77
3
COPYING FUNCTIONS
Select the other copy modes as required, and then press the
[START] button.
7
78 Zooming In/Out Copy Image
Selecting Image Mode
You can select the most suitable quality of the copied image in the following three modes
depending on the originals:
TEXT/PHOTO: Originals with text and photographs mixed
PHOTO: Originals with photographs
TEXT: Originals with text only or with text and fine illustrations only
“TEXT/PHOTO” is set by default at the installation of the equipment.
Place paper in the drawer.
1
Place the original.
2
Press the original mode button until the lamp of the desired mode
is lit.
3
e.g.) Original with photographs
Select the other copy modes as required, and then press the
[START] button.
4
Selecting Image Mode 79
3
COPYING FUNCTIONS
Adjusting Density Level
The automatic copy density mode, which automatically selects the most suitable density level for
the copied image by detecting that of the original, is set by default at the installation of the equip-
ment. You can also adjust the density level as desired manually (=manual copy density mode) in
the following procedure:
Place paper in the drawer.
1
Place the original.
2
Press the density adjustment buttons (
to adjust the density to the desired level.
The density level can be set within 7 stages. One press of each button increases or
decreases the density level by one stage. When you keep pressing either of them, the
density level also keeps changing.
(light) or
(dark))
3
Select the other copy modes as required, and then press the
[START] button.
4
To return it to the automatic copy density mode
Press the
(AUTO) button.
80 Adjusting Density Level
4.
ADVANCED COPYING FUNCTIONS
This chapter describes some useful copying functions, such as how to copy more than one page into a single
sheet of paper or how to print date and time on copy paper.
Copying Both Sides of Card into 1 Page - ID CARD -........................................107
Changing Sizes in Horizontal and Vertical Directions - XY ZOOM -.................109
Registering Functions Frequently Used - JOB MEMORY -...............................111
4
ADVANCED COPYING FUNCTIONS
Copy Menu
This equipment provides you of many convenient copying functions. When you press the select-
ing button C on the “copy mode” main screen, the copy menu appears. Select the desired func-
tion in this menu.
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
More than one copying function can be used together. However, some combinations of functions
are disabled. For the details of the disabled combinations, see the following page:
P.209 “Copying Function Combination Matrix”
Operating in copy menu
When you select the desired function in the menu, press the selecting buttons A, B and C. In this
section, the procedure for selecting the XY zoom function is explained as an example.
Select the desired function with the selecting buttons A, B and C.
e.g.) Press the selecting button C to select “XY ZOOM”.
1
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
A
B
C
Press the same selecting button for several times until you select
the desired function.
2
3
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Press the [ENTER] button.
The function setting screen appears. Perform the setting by following the instructions
displayed on the screen.
82 Copy Menu
The copying functions displayed on the copy menu are shown below.
Function
Description
FINISHING
P.84,
P.86)
Selects finishing modes for paper copied and exited to the receiving tray.
SORT: Exited in the same order as originals in each set.
NONSORT: Exited without being sorted.
(
P.85,
ALTERNATION: Exited while they are being sorted and rotated alternately one
set by one.
MAGAZINE SORT: Exited in a booklet-type page arrangement.
IMAGE SHIFT
P.88)
Makes a binding margin on copy paper. The margin width can be set between 4
mm and 15 mm.
(
LEFT MARGIN: Makes a binding margin on the left side of paper.
RIGHT MARGIN: Makes a binding margin on the right side of paper.
EDGE ERASE
P.90)
Makes a margin along the edge of copy paper. The margin width can be set
between 4 mm and 15 mm.
(
PAPER TYPE
P.64)
Selects the media type of copy paper. This function is available only in the
bypass copying.
(
THICK PAPER1: Thick paper 1 (81 - 105 g/m2)
THICK PAPER2: Thick paper 2 (106 - 163 g/m2)
TRANSPARENCY: Overhead transparencies
DUPLEX
P.92)
Selects whether originals and copy paper are 1-sided or 2-sided.
1>1 SIMPLEX: 1-sided original to 1-sided copy
1>2 DUPLEX: 1-sided original to 2-sided copy
2>2 DUPLEX: 2-sided original to 2-sided copy
2>1 SPLIT: 2-sided original to 1-sided copy
(
BOOK > 2: Booklet-type original to 2-sided copy
DUAL PAGE
P.99)
Makes copies of the double-page spread of a booklet. The right and left pages
are copied separately. The book margin width can be set between 8 mm to 30
mm.
(
ANNOTATION
P.101)
Prints page numbers, date and time.
PAGE NUMBER: Prints page numbers.
(
Page, Date&Time: Print page numbers, date and time.
JOB BUILD
P.102)
Scans and copies originals made of several jobs (= stacks). Settings and scan-
ning methods can be changed for each job. When all the originals have been
scanned, they are copied in one go.
(
2IN1/4IN1
P.104)
Makes copies of 2 or 4 pages of originals into 1 page by reducing their reproduc-
tion ratio.
(
2IN1: Makes copies of 2 pages into 1 page.
4IN1: Makes copies of 4 pages into 1 page.
ID CARD
P.107)
Makes copies of the both sides of a card into 1 page of A4 paper.
(
XY ZOOM
P.109)
Selects the reproduction ratio in the horizontal and vertical directions separately.
(
JOB MEMORY
P.111)
Registers the combination of functions used frequently and recall it as required.
RECALL: Recalls the combination of functions registered.
MEMORY: Registers the combination of functions.
(
Copy Menu 83
4
ADVANCED COPYING FUNCTIONS
Copying in Same Page Order as Originals - Sort Copying -
When you make several sets of copies, the copies can be made to exit in the same order as the
originals in each set. This is called sort copying.
Copied and sorted in 2 sets
1
1
1
2
2
2
3
3
3
Copied in 2 sets without being sorted
1
1
1
2
3
2
2
3
3
Place paper in the drawer.
Place the original.
1
2
When originals are placed on the Reversing Automatic Document Feeder (optional), this
function is automatically set. In this case, proceed to step 5.
Select “FINISHING” in the copy menu, and then press the [ENTER]
button.
3
4
5
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select “SORT”, and then press the [ENTER] button.
FINISHING
SORT
NONSORT
ALTERNATION
The sort copying is set.
Select the other copy modes as required, and then press the
[START] button.
84 Copying in Same Page Order as Originals - Sort Copying -
Sorting Alternately One Set by One - ALTERNATION -
When you make several sets of copies, the copies can be sorted and made to exit alternately
one set by one. This is called alternation. You need to place copy paper in one drawer in a land-
scape direction and place that of the same size in another drawer in a portrait direction in
advance.
A4 or B5 size is available for this function.
Place paper in the drawer.
1
Place the original.
2
Key in the desired number of copies.
3
Select “FINISHING” in the copy menu, and then press the [ENTER]
button.
4
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select “ALTERNATION”, and then press the [ENTER] button.
5
FINISHING
SORT
NONSORT
ALTERNATION
The alternation is set.
Select the other copy modes as required, and then press the
[START] button.
6
Sorting Alternately One Set by One - ALTERNATION - 85
4
ADVANCED COPYING FUNCTIONS
Sorting in Magazine Type Arrangement - MAGAZINE SORT -
The copies can be made to exit in a booklet-type page arrangement. This is called magazine
sort. You can make a booklet by folding and binding the stack of copied paper at its centre.
1
2
3
12
1
10
3
8
5
12
y A3, A4-R and B4 sizes are available for this function.
y The Automatic Duplexing Unit (optional) is required.
y This function cannot be used together with the image shift.
P.88 “Shifting Paper to Make Margin - IMAGE SHIFT -”
Place paper in the drawer.
1
Place the original.
2
Select “FINISHING” in the copy menu, and then press the [ENTER]
button.
3
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select “MAGAZINE SORT”, and then press the [ENTER] button.
4
FINISHING
NONSORT
ALTERNATION
MAGAZINE SORT
86 Sorting in Magazine Type Arrangement - MAGAZINE SORT -
Select the duplex copying mode most suited to the original, and
then press the [ENTER] button.
1>2 DUPLEX: When originals are 1-sided
2>2 DUPLEX: When originals are 2-sided
5
6
MAGAZINE SORT
1>2 DUPLEX
2>2 DUPLEX
The magazine sort is set.
Select the other copy modes as required, and then press the
[START] button.
Sorting in Magazine Type Arrangement - MAGAZINE SORT - 87
4
ADVANCED COPYING FUNCTIONS
Shifting Paper to Make Margin - IMAGE SHIFT -
You can make a margin on copy paper by shifting the whole paper to the right or left. The margin
can be used for punching holes or stapling.
y When you place paper on the bypass tray, register the size of the paper into the equipment in
advance.
y This function cannot be used together with the magazine sort.
P.86 “Sorting in Magazine Type Arrangement - MAGAZINE SORT -”
Place paper in the drawer.
1
Place the original.
2
Select “IMAGE SHIFT” in the copy menu, and then press the
[ENTER] button.
3
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select whether you make a margin on the right or left side of the
paper, and then press the [ENTER] button.
4
LEFT MARGIN: The margin will be made on the left.
RIGHT MARGIN: The margin will be made on the right.
IMAGE SHIFT LEFT MARGIN
RIGHT MARGIN
OFF
88 Shifting Paper to Make Margin - IMAGE SHIFT -
Specify the margin width, and then press the [ENTER] button.
The margin width can be set between 4 mm and 15 mm.
5
6
RIGHT MARGIN
7mm
4mm ---- 15mm
-
+
The image shift is set.
Select the other copy modes as required, and then press the
[START] button.
Shifting Paper to Make Margin - IMAGE SHIFT - 89
4
ADVANCED COPYING FUNCTIONS
Erasing Shadow on Edge - EDGE ERASE -
When you make copies of thick objects such as books, the edge of copied image may be dark-
ened by shadow. When you use this copied image as an original, you can erase this shadow
and make a margin only on the edge of paper with this function.
y Only standard size originals are available.
y When you place paper on the bypass tray, register the size of the paper into the equipment in
advance.
Place paper in the drawer.
1
Place the original.
2
Select “EDGE ERASE” in the copy menu, and then press the
[ENTER] button.
3
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select “ON”, and then press the [ENTER] button.
4
EDGE ERASE
ON
OFF
90 Erasing Shadow on Edge - EDGE ERASE -
Specify the margin width, and then press the [ENTER] button.
The margin width can be set between 4 mm and 15 mm.
5
6
EDGE ERASE
7mm
4mm ---- 15mm
-
+
The edge erase is set.
Select the other copy modes as required, and then press the
[START] button.
Erasing Shadow on Edge - EDGE ERASE - 91
4
ADVANCED COPYING FUNCTIONS
Copying on Both Sides - DUPLEX -
You can select whether originals and paper are 1-sided or 2-sided individually. You can make
copies of 1-sided originals into the both sides of paper so that you can save paper. Also you can
copy a book into the both sides of paper so that you can make another book.
1>1 SIMPLEX ( P.93)
2>1 SPLIT ( P.93)
1>2 DUPLEX ( P.94)
2>2 DUPLEX ( P.94)
92 Copying on Both Sides - DUPLEX -
BOOK > 2 ( P.96)
-13-
3-
-13-
-12-
-15-
-12-
-15-
y To scan 2-sided originals automatically, the Reversing Automatic Document Feeder
(optional) is required.
y To copy on the both sides of paper, the Automatic Duplexing Unit (optional) is required.
Copying on one side
You can copy 1-sided or 2-sided originals on the one side of paper.
Place paper in the drawer.
1
Place the original.
2
Select “DUPLEX” in the copy menu, and then press the [ENTER]
button.
3
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select the duplex copying mode, and then press the [ENTER] but-
ton.
4
1>1 SIMPLEX: 1-sided original to 1-sided copy
2>1 SPLIT: 2-sided original to 1-sided copy
DUPLEX
2>2 DUPLEX
2>1 SPLIT
BOOK > 2
The mode of duplex copying is set.
Copying on Both Sides - DUPLEX - 93
4
ADVANCED COPYING FUNCTIONS
Select the other copy modes as required, and then press the
[START] button.
5
6
Copying starts.
Place the next original if you are using the original glass, and then
select “YES”. Repeat this procedure until all the originals are
scanned.
You can press the [START] button instead of selecting “YES”.
Next original?
YES
NO
When all the originals have been scanned
Select “NO”.
Copying on both sides
You can copy 1-sided or 2-sided originals on the both side of paper.
Place paper in the drawer.
1
2
Use plain paper (64 to 80 g/m ).
Place the original.
2
3
Select “DUPLEX” in the copy menu, and then press the [ENTER]
button.
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
94 Copying on Both Sides - DUPLEX -
Select the duplex copying mode, and then press the [ENTER] but-
ton.
1>2 DUPLEX: 1-sided original to 2-sided copy
2>2 DUPLEX: 2-sided original to 2-sided copy
4
5
DUPLEX
1>1 SIMPLEX
1>2 DUPLEX
2>2 DUPLEX
Select the finishing mode, and then press the [ENTER] button.
BOOK TYPE: Open to left
TABLET TYPE: Open to top
DUPLEX
BOOK TYPE
TABLET TYPE
The mode of duplex copying is set.
Select the other copy modes as required, and then press the
[START] button.
6
7
Copying starts.
Place the next original if you are using the original glass, and then
select “YES”. Repeat this procedure until all the originals are
scanned.
You can press the [START] button instead of selecting “YES”.
Next original?
YES
NO
When all the originals have been scanned
Select “NO”.
Copying on Both Sides - DUPLEX - 95
4
ADVANCED COPYING FUNCTIONS
Copying booklet on both sides
You can copy booklet-type originals such as books or catalogues on the both sides of paper, as
in the same manner as the original.
Place paper in the drawer.
1
2
y Use plain paper (64 to 80 g/m ).
y B5 and A4 sizes are available.
Press the [DRAWER] button to select the drawer to use.
2
3
Select “DUPLEX” in the copy menu, and then press the [ENTER]
button.
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select “BOOK > 2”, and then press the [ENTER] button.
4
DUPLEX
2>2 DUPLEX
2>1 SPLIT
BOOK > 2
96 Copying on Both Sides - DUPLEX -
Select whether the beginning page of the copy is the right or left
page, and also select whether the ending page is the right or left
page. Then press the [ENTER] button.
5
Select among “RIGHT > RIGHT”, “RIGHT > LEFT”, “LEFT > LEFT” and “LEFT > RIGHT”.
BOOK > 2
RIGHT > RIGHT
RIGHT > LEFT
LEFT > LEFT
e.g.) Copy begins with page 2 and ends with page 6: “LEFT > LEFT”
2
3
6
7
Specify the margin width, and then press the [ENTER] button.
The margin width can be set between 8 mm and 30 mm.
6
BOOK MARGIN
15mm
8mm ---- 30mm
-
+
The mode of duplex copying is set.
Copying on Both Sides - DUPLEX - 97
4
ADVANCED COPYING FUNCTIONS
Place the original, and then select other copy modes as required.
Then press the [START] button.
7
Do not place heavy objects (4 kg or more) and do not press on it with force.
Breaking the glass could injure you.
Scanning starts.
Open the next page and place the original, and then select “YES”.
Repeat this procedure until the last page to be copied is left.
You can press the [START] button instead of selecting “YES”.
8
Next original?
YES
YES(SINGLE)
When copying the last page
If the last page is 1-sided, select “YES (SINGLE)”. If it is 2-sided, select “YES”.
When all the originals have been scanned
Select “NO”.
98 Copying on Both Sides - DUPLEX -
Copying Right and Left Pages Separately - DUAL PAGE -
When you place a booklet-type original on the original glass while it is being opened, the right
and left pages of the opened section can be copied separately on different paper. Also, when the
Automatic Duplexing Unit (optional) is installed, they can be copied on both sides of paper. You
do not need to move the original on the original glass.
2
3
2
3
y B5 and A4 sizes are available for this function.
y When you place paper on the bypass tray, register the size of the paper into the equipment in
advance.
Place paper in the drawer.
1
Place an original.
2
Do not place heavy objects (4 kg or more) and do not press on it with force.
Breaking the glass could injure you.
Select “DUAL PAGE” in the copy menu, and then press the
[ENTER] button.
3
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Copying Right and Left Pages Separately - DUAL PAGE - 99
4
ADVANCED COPYING FUNCTIONS
Select “ON”, and then press the [ENTER] button.
4
5
DUAL PAGE
ON
OFF
Specify the margin width, and then press the [ENTER] button.
The margin width can be set between 8 mm and 30 mm.
BOOK MARGIN
15mm
8mm ---- 30mm
-
+
The dual page is set.
Select the other copy modes as required, and then press the
[START] button.
6
7
Copying starts.
Place the original again after turning a page, and select “YES”.
Repeat this procedure until all the originals are scanned.
You can press the [START] button instead of selecting “YES”.
Next original?
YES
NO
When all the pages are scanned
When all the pages are scanned, select “NO”.
100 Copying Right and Left Pages Separately - DUAL PAGE -
Printing Page Number, Date and Time - ANNOTATION -
You can print page numbers, date and time on copied paper.
Place paper in the drawer.
1
Place the original.
2
Select “ANNOTATION” in the copy menu, and then press the
[ENTER] button.
3
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select the item to print, and then press the [ENTER] button.
PAGE NUMBER: Page numbers
Page, Date&Time: Page numbers, date and time
4
ANNOTATION PAGE NUMBER
Page,Date&Time
OFF
The annotation is set.
Select the other copy modes as required, and then press the
[START] button.
5
Printing Page Number, Date and Time - ANNOTATION - 101
4
ADVANCED COPYING FUNCTIONS
Changing Copy Setting on Each Job - JOB BUILD -
This function is useful for originals consisting of several jobs (= stacks). You can change settings
and scanning methods for each job, and when all the originals have been scanned under the dif-
ferent settings, they are copied in one go. A maximum of 250 pages can be handled in one go,
and a maximum of 5 jobs can be scanned.
Some functions cannot be used together with this function or may have some restrictions.
When the following functions are set for the first job, they are also set for the rest:
Paper size selection, Finishing modes, Image shift
Functions not available:
Mixed-size copying, APS, Copying booklet on both sides (“BOOK>2”), Specifying reproduction
ratio manually, XY zoom, Magazine sort, Dual page, 2IN1/4IN1, ID card, Annotation
Place paper in the drawer.
1
Set copy quantities.
2
Select “JOB BUILD” in the copy menu, and then press the [ENTER]
button.
3
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
102 Changing Copy Setting on Each Job - JOB BUILD -
Select “ON”, and then press the [ENTER] button.
4
JOB BUILD
ON
OFF
The job build function is set and the LCD screen shows as follows:
READY
(JOB BUILD)
1
100%
SORT
ZOOM FINISHING EDIT
Place the first job of the originals.
5
6
Select other copy modes as required, and then press the [START]
button.
Scanning starts. When the scanning is finished, the LCD screen shows as follows:
JOB BUILD
Scan next page
End job build
Place the next job.
Repeat steps 6 and 7 until all the jobs are scanned.
7
8
When all the originals have been scanned, select “End job build”,
and then press the [ENTER] button.
JOB BUILD
Scan next page
End job build
Copying starts.
Changing Copy Setting on Each Job - JOB BUILD - 103
4
ADVANCED COPYING FUNCTIONS
Copying 2 or 4 Pages into 1 Page - 2IN1/4IN1 -
2 or 4 pages of originals can be copied into 1 page by reducing their reproduction ratio. When
the Automatic Duplexing Unit (optional) is used, maximum 8 pages can be copied in 1 sheet,
using its both sides.
2IN1
4IN1
2IN1 DUPLEX (a: Side 1, b: Side 2)
y When a copy is turned with the line as a pivot, originals are printed on Side 2 (back face) as
shown.
a
b
a
b
4IN1 DUPLEX (a: Side 1, b: Side 2)
y When a copy is turned with the line as a pivot, originals are printed on Side 2 (back face) as
shown.
a
b
a
b
104 Copying 2 or 4 Pages into 1 Page - 2IN1/4IN1 -
Place paper in the drawer.
1
2
When you place paper on the bypass tray, register the size of the paper into the equip-
ment in advance.
Select “2IN1/4IN1” in the copy menu, and then press the [ENTER]
button.
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select either of 2IN1 or 4IN1, and then press the [ENTER] button.
2IN1: 2 pages of originals to 1 page of copy
4IN1: 4 pages of originals to 1 page of copy
3
4
2IN1/4IN1
2IN1
4IN1
OFF
Select the duplex copying mode, and then press the [ENTER] but-
ton.
1>1 SIMPLEX: 1-sided original to 1-sided copy
1>2 DUPLEX: 1-sided original to 2-sided copy
2>2 DUPLEX: 2-sided original to 2-sided copy
2>1 SPLIT: 2-sided original to 1-sided copy
2IN1
1>1 SIMPLEX
1>2 DUPLEX
2>2 DUPLEX
Copying 2 or 4 Pages into 1 Page - 2IN1/4IN1 - 105
4
ADVANCED COPYING FUNCTIONS
Select the finishing mode, and then press the [ENTER] button.
BOOK TYPE: Open to left
TABLET TYPE: Open to top
5
DUPLEX
BOOK TYPE
TABLET TYPE
When “1>1 SIMPLEX” is selected in step 4, this procedure is not necessary.
The 2IN1 / 4IN1 is set.
Select the other copy modes as required, and then press the
[START] button.
6
106 Copying 2 or 4 Pages into 1 Page - 2IN1/4IN1 -
Copying Both Sides of Card into 1 Page - ID CARD -
The both sides of a card-sized original can be copied into one side of A4 paper. This function is
useful when you need to copy massive amounts of 2-sided cards.
Front side
Back side
Place paper in the drawer.
1
2
Select “ID CARD” in the copy menu, and then press the [ENTER]
button.
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select “ON”, and then press the [ENTER] button.
3
4
ID CARD
ON
OFF
The ID card function is set.
Raise the Platen Cover (optional) or the Reversing Automatic Docu-
ment Feeder (optional) / Automatic Document Feeder (optional).
Copying Both Sides of Card into 1 Page - ID CARD - 107
4
ADVANCED COPYING FUNCTIONS
Place a card original on the original glass.
Place the card face down, aligning and pushing it to the left rear corner of the original
glass.
5
Lower the Platen Cover (optional) or the Reversing Automatic Doc-
ument Feeder (optional) / Automatic Document Feeder (optional)
carefully.
6
7
Select the other copy modes as required, and then press the
[START] button.
The scanning of its top side starts. The LCD screen shows as follows:
Set back of ID CARD
1
100%
SORT
Raise the Platen Cover (optional) or the Reversing Automatic Docu-
ment Feeder (optional) / Automatic Document Feeder (optional).
8
Turn over the card and place it on the original glass again.
Align and push it to the left rear corner of the original glass.
9
Lower the Platen Cover (optional) or the Reversing Automatic Doc-
ument Feeder (optional) / Automatic Document Feeder (optional)
carefully.
10
Press the [START] button.
11
108 Copying Both Sides of Card into 1 Page - ID CARD -
Changing Sizes in Horizontal and Vertical Directions - XY ZOOM -
You can select each reproduction ratio of the horizontal and vertical directions separately.
Place paper in the drawer.
1
Place the original.
2
Select “XY ZOOM” in the copy menu, and then press the [ENTER]
button.
3
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Press the selecting button B (–) or C (+) to set the desired reproduc-
tion ratio.
One press of each button increases or decreases the reproduction ratio by 1%. When
you keep pressing either or them, the reproduction ratio also keeps changing. The
reproduction ratio can be set from 25% to 200%.
4
The direction can be switched with the selecting button A (X/Y).
XY ZOOM
X:120% Y: 80%
25% ---- 200%
X/Y
-
+
Press the [ENTER] button.
The reproduction ratios are set.
5
Changing Sizes in Horizontal and Vertical Directions - XY ZOOM - 109
4
ADVANCED COPYING FUNCTIONS
Press the [COPY] button several times until the lamp of the desired
paper size is lit.
6
e.g.) Selecting A4 for copy paper
You can select the desired paper size with the [DRAWER] button in the same procedure.
y When standard size paper other than A3, A4, A4-R, A5-R or B4 is placed, register
this size as “OTHER” size in advance.
y
P.47 “Registering other standard sizes”
Select the other copy modes as required, and then press the
[START] button.
7
110 Changing Sizes in Horizontal and Vertical Directions - XY ZOOM -
Registering Functions Frequently Used - JOB MEMORY -
You can register the combination of functions frequently used, and recall it as required. The
combinations once registered will not be deleted by turning the power of the equipment OFF. Up
to 4 combinations of functions can be registered.
• Reproduction ratio: 85%
• Copy quantity: 20
MEMORY
• Copy density: Automatic
• Paper size: B5
• Reproduction ratio: 85%
• Copy quantity: 20
RECALL
• Copy density: Automatic
• Paper size: B5
The functions available are shown below.
Original size, APS/AMS, Mixed-size copying, Reproduction ratio, Image mode, Copy density,
Finishing modes, Image shift, Edge erase, Paper type, Duplex, Dual page, Annotation, Job
build, 2IN1/4IN1, XY zoom
Registering combination of functions
Set all functions you want to register.
e.g.) Reproduction ratio: 85%, copy qty.: 20, density: automatic density mode, paper size:
B5
1
Select “JOB MEMORY” in the copy menu, and then press the
[ENTER] button.
2
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select “MEMORY”, and then press the [ENTER] button.
3
JOB MEMORY
RECALL
MEMORY
Registering Functions Frequently Used - JOB MEMORY - 111
4
ADVANCED COPYING FUNCTIONS
Select among “MEMORY1”, “MEMORY2”, “MEMORY3” and
“MEMORY4”. Then press the [ENTER] button.
4
e.g.) Selecting “MEMORY4”
MEMORY
MEMORY2
MEMORY3
MEMORY4
A mark on the left end of the memory name indicates that the combination of functions
has already been registered to the memory. When you select a memory number already
registered, the memory content will be overwritten.
The combination of the functions has been registered.
Recalling combination of functions
Select “JOB MEMORY” in the copy menu, and then press the
[ENTER] button.
1
FINISHING DUPLEX 2IN1/4IN1
IMAGE SHIFT DUAL PAGE ID CARD
EDGE ERASE ANNOTATION XY ZOOM
PAPER TYPE JOB BUILD JOB MEMORY
Select “RECALL”, and then press the [ENTER] button.
2
JOB MEMORY
RECALL
MEMORY
112 Registering Functions Frequently Used - JOB MEMORY -
Select among “MEMORY1”, “MEMORY2”, “MEMORY3” and
“MEMORY4”. Then press the [ENTER] button.
e.g.) Selecting “MEMORY4”
3
4
RECALL
MEMORY2
MEMORY3
MEMORY4
A memory to which the combination of functions has already been registered has a mark
on the left end of the memory name.
The combination of the functions is recalled.
Select the other copy modes as required, and then press the
[START] button.
Registering Functions Frequently Used - JOB MEMORY - 113
4
ADVANCED COPYING FUNCTIONS
114 Registering Functions Frequently Used - JOB MEMORY -
5.
CHANGING EQUIPMENT’S SETTINGS
This chapter describes how to change each setting of this equipment.
Before Changing the Settings .............................................................................117
Displaying the “user functions mode” main screen .........................................................................117
Operating buttons for changing the settings ...................................................................................118
Date and Time .......................................................................................................119
Clock setting....................................................................................................................................119
Display Language Setting....................................................................................122
Timer Setting.........................................................................................................128
Time of automatic low power mode ................................................................................................130
Department Code..................................................................................................141
Changing department names or codes...........................................................................................145
Deleting department codes .............................................................................................................148
Printing out counter values..............................................................................................................152
Cancelling department management ..............................................................................................153
Menu Customize ...................................................................................................155
APS / AMS..............................................................................................................157
Various List Printing.............................................................................................165
Menu List Printing.................................................................................................167
ROM Version Display............................................................................................168
Before Changing the Settings
The settings of this equipment can be changed depending on your usage. The screen and the
basic button operation are explained in this section.
Displaying the “user functions mode” main screen
To change the settings, operate the buttons on the control panel viewing the menu. Press the
[USER FUNCTIONS] button on the control panel.
The “user functions mode” main screen is displayed. Select the item from this screen and
change the setting.
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Checking the total number of sheets ever copied or printed
You can check the total number of sheets ever copied or printed. The total number of sheets is
displayed on the top right corner of the “user functions mode” main screen.
The total number of sheets cannot be reset.
Checking the menu structure
The menu of this equipment can be printed as a list. See the page below for details.
P.167 “Menu List Printing”
Menu items not described in this manual
This operator’s manual explains the general settings and the setting of copying function in this
equipment. The settings used when the options such as Fax or Scanner are installed are
described in the manuals that come with the options.
Before Changing the Settings 117
5
CHANGING EQUIPMENT’S SETTINGS
Operating buttons for changing the settings
Use the following buttons when changing the settings.
[FUNCTION CLEAR] button
[CANCEL] button
/
buttons
buttons
/
[ENTER] button
Digital keys
[CLEAR/STOP] button
[FUNCTION CLEAR] button: Use this to return the display to the “user functions mode” main
screen.
[CANCEL] button:
Use this to cancel the selected operation. The screen returns to
the previous menu.
/
button:
button:
Use this to move the cursor to the right and left.
/
Use this to move the cursor up and down to select the menu
and item.
[ENTER] button:
Digital keys:
Use this to perform the selection of the menu and item.
Use this to enter the values.
[CLEAR/STOP] button:
Use this to clear the entered value in one go.
Examples of the menu operation are shown below.
INITIAL SETUP
01.DATE & TIME
02.LANGUAGE
When the button is pressed, the cursor moves up.
03.TERMINAL ID
When the button is pressed, the cursor moves down.
The [ENTER] button or digital key [0] [1] *1
The specified operation is performed
and the next menu appears.
LANGUAGE
01.English
02.Français
03.Espanôl
The [ENTER] button The [CANCEL]
or digital key [1] *1 button
The specified operation is performed and
the screen returns to the previous menu.
The specified operation is canceled and
the screen returns to the previous menu.
*1 At the head of items, 1 or 2-digit numbers are attached. Instead of pressing the
button, keying in this number selects and performs the item directly.
,
and [ENTER]
Returning to the “copy mode” main screen
Press the
(copy mode) button. The screen returns to the “copy mode” main screen.
118 Before Changing the Settings
Date and Time
This section describes how to set a clock and the time stamp display.
Clock setting
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “INITIAL SETUP” with
the [ENTER] button.
and
buttons, and then press
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “DATE & TIME” with
[ENTER] button.
and
buttons, and then press the
INITIAL SETUP
01.DATE & TIME
02.LANGUAGE
03.TERMINAL ID
Select “SETTING” with
[ENTER] button.
and
buttons, and then press the
DATE & TIME
01.SETTING
02.TIME FORMAT
03.DATE FORMAT
Date and Time 119
5
CHANGING EQUIPMENT’S SETTINGS
Key in the date.
e.g.) April 10, 2006: [2] [0] [0] [6] [0] [4] [1] [0]
5
SETTING
YYYY-MM-DD DAY
2006-04-10 SUN
HH:MM
09:45 AM
Select the date of the week with the
and
buttons, and then
6
7
press the
button.
SETTING
YYYY-MM-DD DAY
2006-04-10 MON
HH:MM
09:45 AM
Key in the time.
e.g.) 10:30 am: [1] [0] [3] [0]
SETTING
YYYY-MM-DD DAY
2006-04-10 MON
HH:MM
10:30 AM
If 12-hour display is set, press the
or
button to switch the a.m./p.m.
After all the items have finished being entered, press the [ENTER]
button.
8
9
The time is set and the screen returns to the menu in step 4.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
10
The screen returns to the “copy mode” main screen.
120 Date and Time
Date and time display
You can set the display format of the date and time by selecting each item from the “DATE &
TIME” menu.
DATE & TIME
01.SETTING
02.TIME FORMAT
03.DATE FORMAT
Time display format
Select the time display format.
24 HOUR: 24-hour display
12 HOUR: 12-hour display
TIME FORMAT
1.24 HOUR
2.12 HOUR
Date format
Select the date display format.
e.g.) April 10, 2006
YYYY-MM-DD 2006-04-10
MM-DD-YYYY 04-10-2006
DD-MM-YYYY 10-04-2006
YY-MM-DD
MM-DD-YY
DD-MM-YY
06-04-10
04-10-06
10-04-06
DATE FORMAT
1.YYYY-MM-DD
2.MM-DD-YYYY
3.DD-MM-YYYY
Month format
Select the month display.
NUMERIC: Display the month using the numbers.
NAME:
Display the month using letters of alphabet. (E.g.: Jan, Feb, etc.)
MONTH MODE
1.NUMERIC
2.NAME
Date and Time 121
5
CHANGING EQUIPMENT’S SETTINGS
Display Language Setting
This section describes how to switch the display language on the screen.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “INITIAL SETUP” with
the [ENTER] button.
and
buttons, and then press
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “LANGUAGE” with
[ENTER] button.
and
buttons, and then press the
INITIAL SETUP
01.DATE & TIME
02.LANGUAGE
03.TERMINAL ID
Select the display language with the
press the [ENTER] button.
and
buttons, and then
LANGUAGE
01.English
02.Français
03.Espanôl
The display language is set and the screen returns to the menu in step 3.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
5
The screen returns to the “user functions mode” main screen.
122 Display Language Setting
Press the
(copy mode) button.
6
The screen returns to the “copy mode” main screen.
Display Language Setting 123
5
CHANGING EQUIPMENT’S SETTINGS
Paper Size Setting
This section describes how to set the paper size placed in the drawer or on the bypass tray.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
and
buttons, and then
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “DRAWER SIZE” with
the [ENTER] button.
and
buttons, and then press
GENERAL SETTINGS
01.DRAWER SIZE
02.WALKUP SCREEN
03.TIMERS
124 Paper Size Setting
Select the desired drawer with
the [ENTER] button.
and
buttons, and then press
5
6
DRAWER SIZE
01.DRAWER 1
02.DRAWER 2
03.DRAWER 3
Select the desired paper size with
press the [ENTER] button.
and
buttons, and then
Select paper size
01.A3
02.A4
03.A4-R
The paper size is set and the screen returns to the menu in step 5.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
7
8
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
Paper Size Setting 125
5
CHANGING EQUIPMENT’S SETTINGS
Walkup Screen Setting
This section describes how to set the screen when the power of the equipment is turned ON. In
the initial screen set at the time of shipping, the "copy mode” main screen is displayed.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
buttons, and then
buttons, and then
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
and
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “WALKUP SCREEN” with
press the [ENTER] button.
and
GENERAL SETTINGS
01.DRAWER SIZE
02.WALKUP SCREEN
03.TIMERS
126 Walkup Screen Setting
Select the desired walkup screen with
then press the [ENTER] button.
Choose one among COPY, FAX or SCAN.
and
buttons, and
5
WALKUP SCREEN
1.COPY
2.FAX
3.SCAN
y “FAX” is displayed only when the Fax Kit (optional) is installed.
y “SCAN” is displayed only when the Scanner Upgrade Kit (optional) is installed.
The walkup screen is set and the screen returns to the menu in step 4.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
6
7
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
After the mode has been changed and the time of the automatic function clear has
passed, the setting becomes enabled.
Walkup Screen Setting 127
5
CHANGING EQUIPMENT’S SETTINGS
Timer Setting
This section describes how to set the following timers.
AUTO CLEAR: Time until the selected setting is cleared automatically
AUTO LOW POWER: Time until the low power mode is entered
AUTO SLEEP: Time until the sleep mode is entered after the low power mode has
been entered
For the low power mode and sleep mode, see “EPA ENERGY STAR” on the first page of this
manual.
Time of automatic function clear
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
2
3
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
and
buttons, and then
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
128 Timer Setting
Select “TIMERS” with
[ENTER] button.
and
buttons, and then press the
4
5
6
GENERAL SETTINGS
01.DRAWER SIZE
02.WALKUP SCREEN
03.TIMERS
Select “AUTO CLEAR” with
[ENTER] button.
and
buttons, and then press the
TIMERS
1.AUTO CLEAR
2.AUTO POWER SAVE
3.AUTO SLEEP
Select the time of “AUTO CLEAR” with
then press the [ENTER] button.
and
buttons, and
Selectable times are as follows. (Unit: second)
15, 30, 45, 60, 75, 90, 105, 120, 135, 150, 180, 210, 240, 270, 300
TIMERS
AUTO
CLEAR:
300SEC
15SEC
45
The time of the automatic function clear is set and the screen returns to the menu in step
5.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
7
8
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
Timer Setting 129
5
CHANGING EQUIPMENT’S SETTINGS
Time of automatic low power mode
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
and
buttons, and then
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “TIMERS” with
[ENTER] button.
and
buttons, and then press the
GENERAL SETTINGS
01.DRAWER SIZE
02.WALKUP SCREEN
03.TIMERS
130 Timer Setting
Select “AUTO LOW POWER” with
press the [ENTER] button.
and
buttons, and then
5
6
TIMERS
1.AUTO CLEAR
2.AUTO POWER SAVE
3.AUTO SLEEP
Select the time of “AUTO LOW POWER” with
and then press the [ENTER] button.
Selectable times are as follows. (Unit: minute)
and
buttons,
1, 2, 3, 4, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 70, 80, 90, 100, 110, 120, 150, 180,
210, 240
TIMERS
AUTO POWER
SAVE:
240MIN
1MIN
15
The time of the automatic low power mode is set and the screen returns to the menu in
step 5.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
7
8
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
Timer Setting 131
5
CHANGING EQUIPMENT’S SETTINGS
Time of automatic sleep mode
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
and
buttons, and then
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “TIMERS” with
[ENTER] button.
and
buttons, and then press the
GENERAL SETTINGS
01.DRAWER SIZE
02.WALKUP SCREEN
03.TIMERS
132 Timer Setting
Select “AUTO SLEEP” with
[ENTER] button.
and
buttons, and then press the
5
6
TIMERS
1.AUTO CLEAR
2.AUTO POWER SAVE
3.AUTO SLEEP
Select the time of “AUTO SLEEP” with
then press the [ENTER] button.
and
buttons, and
Selectable times are as follows. (Unit: minute)
3, 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 70, 80, 90, 100, 110, 120, 150, 180, 210,
240
TIMERS
AUTO
SLEEP:
240MIN
3MIN
15
The time of the automatic sleep mode is set and the screen returns to the menu in step 5.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
7
8
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
Timer Setting 133
5
CHANGING EQUIPMENT’S SETTINGS
Weekly Timer Setting
This section describes how to set the weekly timer. Use the weekly timer to set the equipment to
enter the sleep mode automatically at the specified time. You can set the equipment to enter the
stand-by status when the office hour starts, and to enter the sleep mode when the office hour
ends. The time can be set for each day of the week.
y If the equipment is in the energy saving mode at the time when the weekly timer is set to turn
the power OFF, it does not become ready status at the time when the weekly timer is set to
turn the power ON. In this case, make the equipment in the ready status by following the pro-
cedure below.
-
-
Press the [ENERGY SAVER] button.
Open the Platen Cover (optional) or Reversing Automatic Document Feeder (optional) /
Automatic Document Feeder (optional).
-
Connect the equipment to a PC with a USB cable.
y If the power of the equipment is turned OFF, the weekly timer function does not work.
When the Fax Kit (optional) is used, it is recommended to use this function for the energy sav-
ing.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
2
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
134 Weekly Timer Setting
Select “GENERAL SETTINGS” with
press the [ENTER] button.
and
buttons, and then
3
4
5
6
7
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “WEEKLY TIMER” with
the [ENTER] button.
and
buttons, and then press
GENERAL SETTINGS
02.WALKUP SCREEN
03.TIMERS
04.WEEKLY TIMER
Select “ON” with
button.
and
buttons, and then press the [ENTER]
WEEKLY TIMER
1.OFF
2.ON
Select the desired day of the week with the
and then press the [ENTER] button.
and
buttons,
WEEKLY TIMER
1.SUNDAY
2.MONDAY
3.TUESDAY
Key in the time to turn the power ON, and then press the [ENTER]
button.
e.g.) 10:30: [1] [0] [3] [0]
SUNDAY
ON TIME:
HH:MM
10:30 AM
If 12-hour display is set, press the
or
button to switch the a.m./p.m.
Weekly Timer Setting 135
5
CHANGING EQUIPMENT’S SETTINGS
Key in the time to turn the power OFF, and then press the [ENTER]
button.
8
SUNDAY
OFF TIME: HH:MM
07:30 PM
The time to turn the power ON/OFF is set and the screen returns to the menu in step 6.
Set the time to turn the power ON/OFF for each day of the week by
following steps 6 to 8.
9
When all the setting is completed, select “COMPLETE”, and then
press the [ENTER] button.
10
WEEKLY TIMER
6.FRIDAY
7.SATURDAY
8.COMPLETE
The weekly timer is set and the screen returns to the menu in step 4.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
11
12
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
Clearing the weekly timer
Select “OFF” in step 5.
The time settings remain even if the weekly timer is cleared. They become valid when the
weekly timer is set to ON again.
136 Weekly Timer Setting
Volume Adjustment
This section describes how to set the alarm volume, key touch volume, ringer volume and moni-
tor volume.
The menu of this setting is displayed only when the Fax Kit (optional) is installed. When it is not
installed, the touch key tone can be switched ON/OFF.
P.139 “Touch Key Tone Setting”
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
and
and
buttons, and then
buttons, and then
buttons, and then
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “SPEAKER VOLUME” with
press the [ENTER] button.
GENERAL SETTINGS
03.TIMERS
04.WEEKLY TIMER
05.SPEAKER VOLUME
Volume Adjustment 137
5
CHANGING EQUIPMENT’S SETTINGS
Select the desired volume with the
press the [ENTER] button.
The volume of the following items can be set:
Alarm volume, Key touch volume, Ringer volume and Monitor volume
e.g.) When “ALARM VOLUME” is selected
and
buttons, and then
5
6
SPEAKER VOLUME
1.ALARM VOLUME
2.KEY TOUCH VOLUME
3.RINGER VOLUME
Adjust the volume with the
[ENTER] button.
and
buttons, and then press the
The volume can be adjusted in eight levels from 0 (no sound) to 7(max.).
ALARM VOLUME
VOLUME:
7
0
3
The volume is set and the screen returns to the menu in step 5.
Adjust the other volumes as required by following steps 5 and 6.
7
8
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
9
The screen returns to the “copy mode” main screen.
138 Volume Adjustment
Touch Key Tone Setting
This section describes how to switch ON/OFF the touch tone when the buttons on the control
panel are pressed.
The menu of this setting is displayed only when the Fax Kit (optional) is not installed. When it is
installed, all of the volume can be adjusted.
P.137 “Volume Adjustment”
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
buttons, and then
buttons, and then
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
and
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “TOUCH KEY TONE” with
press the [ENTER] button.
and
GENERAL SETTINGS
03.TIMERS
04.WEEKLY TIMER
05.TOUCH KEY TONE
Touch Key Tone Setting 139
5
CHANGING EQUIPMENT’S SETTINGS
Select “ON” or “OFF” with
[ENTER] button.
and
buttons, and then press the
5
TOUCH KEY TONE
1.OFF
2.ON
The screen returns to the menu in step 4.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
6
7
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
140 Touch Key Tone Setting
Department Code
This section describes how to manage and understand the records of copying, Fax transmis-
management.
When the department code management is enabled, a screen prompting you to enter your
department code is displayed before you use this equipment. Thus the unauthorized use of this
equipment is prevented.
P.33 “Turning power ON”
Setting department codes
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
2
3
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
and
buttons, and then
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Department Code 141
5
CHANGING EQUIPMENT’S SETTINGS
Select “DEPARTMENT CODE” with
press the [ENTER] button.
and
buttons, and then
4
5
6
GENERAL SETTINGS
04.WEEKLY TIMER
05.SPEAKER VOLUME
06.DEPARTMENT CODE
Select “YES” with
button.
and
buttons, and then press the [ENTER]
DEPARTMENT CODE
1.YES
2.NO
Select “NEW” with
[ENTER] button.
and
buttons, and then press the
DEPARTMENT CODE
1.RECOVER OLD DATA
2.NEW
y This screen is not displayed when you set the department management of this equip-
ment for the first time or when the department management is already enabled
(“YES” in step 5 is already selected).
y If “NEW” is selected, the master code and department code which have been set by
that time will be deleted. (If you use the master code and department code already
registered, select “RECOVER OLD DATA”.)
Then, set a master code (administrator’s code). If the External Keyboard (optional) is
installed, proceed to step 7. If not, proceed to step 8.
142 Department Code
Enter the master code name, and then press the [ENTER] button.
7
MASTER CODE
MASTER CODE NUMBER:
01
ENTER MASTER CODE NAME(MAX20):
y Enter the master code name only when the External Keyboard (optional) is installed.
y A maximum of 20 desired letters can be set for the master code name.
y The master code name entry can be omitted. In this case, do not enter the master
code name and just press the [ENTER] button.
For how to enter letters, see the manual which comes with the Fax Kit or Scanner
Upgrade Kit (both optional).
Key in the master code, and then press the [ENTER] button.
8
9
MASTER CODE
MASTER CODE NUMBER:
ENTER MASTER CODE:
01
12345
y Enter 5 digits for the master code.
y Do not forget this master code because it is required for setting or deleting each
department code.
The master code is now registered on the department number “01”. Then, set a
department code.
Register a department code. Key in the desired department number,
and then press the [ENTER] button.
DEPARTMENT CODE
ENTER DEPARTMENT NUMBER(1-99):
2
Select the desired department number from “02” to “99”. (The master code is already
registered on “01”.)
If the External Keyboard (optional) is installed, proceed to step 10. If not, proceed to step
11.
Department Code 143
5
CHANGING EQUIPMENT’S SETTINGS
Enter the department name, and then press the [ENTER] button.
10
DEPARTMENT CODE
DEPARTMENT NUMBER:
02
ENTER DEPARTMENT NAME(MAX20):
y Enter the department name only when the External Keyboard (optional) is installed.
y A maximum of 20 desired letters can be set for the department name.
y The department name entry can be omitted. In this case, do not enter the department
name and just press the [ENTER] button.
For how to enter letters, see the manual which comes with the Fax Kit or Scanner
Upgrade Kit (both optional).
Key in the department code, and then press the [ENTER] button.
11
DEPARTMENT CODE
DEPARTMENT NUMBER:
ENTER DEPARTMENT CODE:
02
55310
y Enter 5 digits for the department code.
y Department codes already registered cannot be keyed in.
The screen returns to the one in step 9.
Register the other department codes as required, following steps
from 9 to 11.
12
13
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
14
The screen returns to the “copy mode” main screen.
144 Department Code
Changing department names or codes
This section describes how to change the department names or codes already registered. Key
in the master code in the department code entry screen, and then proceed to the following
steps:
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
and
and
buttons, and then
buttons, and then
buttons, and then
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “DEPARTMENT CODE” with
press the [ENTER] button.
GENERAL SETTINGS
04.WEEKLY TIMER
05.SPEAKER VOLUME
06.DEPARTMENT CODE
Department Code 145
5
CHANGING EQUIPMENT’S SETTINGS
Select “YES” with
button.
and
buttons, and then press the [ENTER]
5
DEPARTMENT CODE
1.YES
2.NO
Key in the department number you want to change its setting, and
then press the [ENTER] button.
6
7
DEPARTMENT CODE
ENTER DEPARTMENT NUMBER(1-99):
2
The screen below is displayed for approx. 2 seconds.
DEPARTMENT CODE
DEPARTMENT NUMBER:
02
Already assigned
Select “MODIFY” with
[ENTER] button.
and
buttons, and then press the
DEPARTMENT CODE
1.DELETE
2.MODIFY
3.RETAIN
If the External Keyboard (optional) is installed, proceed to step 8. If not, proceed to step
9.
146 Department Code
Enter a new department name, and then press the [ENTER] button.
8
DEPARTMENT CODE
DEPARTMENT NUMBER:
02
ENTER DEPARTMENT NAME(MAX20):
y Enter the department name only when the External Keyboard (optional) is installed.
y A maximum of 20 desired letters can be set for the department name.
y The department name entry can be omitted. In this case, do not enter the department
name and just press the [ENTER] button.
For how to enter letters, see the manual which comes with the Fax Kit or Scanner
Upgrade Kit (both optional).
Key in a new department code, and then press the [ENTER] button.
9
DEPARTMENT CODE
DEPARTMENT NUMBER:
ENTER DEPARTMENT CODE:
02
37802
y Enter 5 digits for the department code.
y Department codes already registered cannot be entered.
The setting has been changed and the screen returns to the one in step 6.
Change the other department codes as required, following steps
from 6 to 9.
10
11
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
12
The screen returns to the “copy mode” main screen.
Department Code 147
5
CHANGING EQUIPMENT’S SETTINGS
Deleting department codes
This section describes how to delete the department codes already registered. Key in the mas-
ter code in the department code entry screen, and then proceed to the following steps:
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
and
and
buttons, and then
buttons, and then
buttons, and then
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “DEPARTMENT CODE” with
press the [ENTER] button.
GENERAL SETTINGS
04.WEEKLY TIMER
05.SPEAKER VOLUME
06.DEPARTMENT CODE
148 Department Code
Select “YES” with
button.
and
buttons, and then press the [ENTER]
5
6
DEPARTMENT CODE
1.YES
2.NO
Key in the department number you want to delete, and then press
the [ENTER] button.
DEPARTMENT CODE
ENTER DEPARTMENT NUMBER(1-99):
2
The screen below is displayed for approx. 2 seconds.
DEPARTMENT CODE
DEPARTMENT NUMBER:
02
Already assigned
Select “DELETE” with
[ENTER] button.
and
buttons, and then press the
7
DEPARTMENT CODE
1.DELETE
2.MODIFY
3.RETAIN
Master codes cannot be deleted but only department codes can be deleted.
The department code is now deleted and the screen returns to the one in step 6.
Delete the other department codes as required, following steps 6
and 7.
8
9
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
10
The screen returns to the “copy mode” main screen.
Department Code 149
5
CHANGING EQUIPMENT’S SETTINGS
Clearing counter values
This section describes how to clear counter values indicating the total number of pages copied
in each department. Key in the master code in the department code entry screen, and then pro-
ceed to the following steps:
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
and
and
buttons, and then
buttons, and then
buttons, and then
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “GENERAL SETTINGS” with
press the [ENTER] button.
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “DEPARTMENT CODE” with
press the [ENTER] button.
GENERAL SETTINGS
04.WEEKLY TIMER
05.SPEAKER VOLUME
06.DEPARTMENT CODE
150 Department Code
Select “YES” with
button.
and
buttons, and then press the [ENTER]
5
6
DEPARTMENT CODE
1.YES
2.NO
Key in the department number you want to clear its counter, and
then press the [ENTER] button.
Keying in the department number of the master code (“01”) will clear all the department
number counter values.
DEPARTMENT CODE
ENTER DEPARTMENT NUMBER(1-99):
2
The screen below is displayed for approx. 2 seconds.
DEPARTMENT CODE
DEPARTMENT NUMBER:
02
Already assigned
Select “COUNT CLEAR” with
the [ENTER] button.
and
buttons, and then press
7
8
DEPARTMENT CODE
2.MODIFY
3.RETAIN
4.COUNT CLEAR
The screen below is displayed for approx. 2 seconds.
DEPARTMENT CODE
DEPARTMENT NUMBER:
02
Cleared
The counter value is now cleared and the screen returns to the one in step 6.
Clear the other counter values as required, following steps 6 and 7.
Department Code 151
5
CHANGING EQUIPMENT’S SETTINGS
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
9
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
10
The screen returns to the “copy mode” main screen.
Printing out counter values
This section describes how to print out the value of the total number of pages copied in each
department.
y Counter values to be printed belong to the department which you entered on the department
code entry screen.
y If you want to print the counter values of all the departments registered, key in the master
code in the department code entry screen, and then proceed to the following steps:
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “LISTS” with
[ENTER] button.
and
buttons, and then press the
2
USER FUNCTIONS
1216
01.DEFAULT SETTINGS
02.LISTS
03.INITIAL SETUP
152 Department Code
Select “DEPARTMENT CODE” with
press the [ENTER] button.
and
buttons, and then
3
LISTS
1.DEPARTMENT CODE
3.SUPPLY NOTICE
The department code list is printed out.
See the list example in the following page:
P.211 “Department code list”
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
4
5
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
Cancelling department management
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
2
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Department Code 153
5
CHANGING EQUIPMENT’S SETTINGS
Select “GENERAL SETTINGS” with
press the [ENTER] button.
and
buttons, and then
3
4
5
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “DEPARTMENT CODE” with
press the [ENTER] button.
and
buttons, and then
GENERAL SETTINGS
04.WEEKLY TIMER
05.SPEAKER VOLUME
06.DEPARTMENT CODE
Select “NO” with
button.
and
buttons, and then press the [ENTER]
DEPARTMENT CODE
1.YES
2.NO
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
6
7
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
154 Department Code
Menu Customize
This section describes how to change the setting of the custom function. The copy function
which has been registered as custom function can be quickly recalled.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “COPY SETUP” with
[ENTER] button.
and
buttons, and then press the
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “MENU CUSTOMIZE” with
press the [ENTER] button.
and
buttons, and then
COPY SETUP
01.MENU CUSTOMIZE
02.APS/AMS
03.IMAGE MODE
Menu Customize 155
5
CHANGING EQUIPMENT’S SETTINGS
Select the setting you want to register to the menu customize with
5
the
and
buttons, and then press the [ENTER] button.
The following copy functions can be registered:
Finishing modes, Duplex, 2IN1/4IN1, Image shift, Dual-page and ID card
MENU CUSTOMIZE
4.IMAGE SHIFT
5.DUAL PAGE
6.ID CARD
The item of the menu customize is set and the screen returns to the menu in step 4.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
6
7
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
156 Menu Customize
APS / AMS
This section describes how to set the initial selection between “Automatic Paper Selection” and
“Automatic Magnification Selection”.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
buttons, and then press the
buttons, and then press the
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “COPY SETUP” with
[ENTER] button.
and
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “APS/AMS” with
[ENTER] button.
and
COPY SETUP
01.MENU CUSTOMIZE
02.APS/AMS
03.IMAGE MODE
APS / AMS 157
5
CHANGING EQUIPMENT’S SETTINGS
Select the initial selection with the
press the [ENTER] button.
APS: Automatic Paper Selection is initially selected.
AMS: Automatic Magnification Selection is initially selected.
NO: No initial selection
and
buttons, and then
5
APS/AMS
1.APS
2.AMS
3.NO
The initial selection is set and the screen returns to the menu in step 4.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
6
7
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
158 APS / AMS
Image Mode
This section describes how to change the image mode.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
buttons, and then press the
buttons, and then press the
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “COPY SETUP” with
[ENTER] button.
and
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “IMAGE MODE” with
[ENTER] button.
and
COPY SETUP
01.MENU CUSTOMIZE
02.APS/AMS
03.IMAGE MODE
Image Mode 159
5
CHANGING EQUIPMENT’S SETTINGS
Select the image mode with the
the [ENTER] button.
and
buttons, and then press
5
TEXT/PHOTO: Originals with text and photographs mixed
PHOTO:
TEXT:
Originals with photogravure
Originals with text (or text and line art) only
IMAGE MODE
1.TEXT/PHOTO
2.PHOTO
3.TEXT
The image mode is set and the screen returns to the menu in step 4.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
6
7
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
160 Image Mode
Density Adjustment
This section describes how to switch the mode of the density adjustment.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
buttons, and then press the
buttons, and then press the
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “COPY SETUP” with
[ENTER] button.
and
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “LIGHT/DARK” with
[ENTER] button.
and
COPY SETUP
02.APS/AMS
03.IMAGE MODE
04.LIGHT/DARK
Density Adjustment 161
5
CHANGING EQUIPMENT’S SETTINGS
Select the mode of the density adjustment with the
tons, and then press the [ENTER] button.
and
but-
5
6
AUTO:
The equipment detects the density of an original and sets the appropriate
copy density automatically.
MANUAL:
You can set the copy density manually.
LIGHT/DARK
1.AUTO
2.MANUAL
If “AUTO” is selected, the automatic copy density mode is set and the screen returns to
the menu in step 4. Proceed to step 7.
When you select “MANUAL”, proceed to step 6.
Select the density with the
[ENTER] button.
and
buttons, and then press the
The density can be set in seven levels from “LIGHT3” (Lighter) to “DARK3” (Darker).
LIGHT/DARK
1.LIGHT3
2.LIGHT2
3.LIGHT1
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
7
8
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
162 Density Adjustment
Finishing Mode
This section describes how to set the initial finishing mode.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “DEFAULT SETTINGS” with
press the [ENTER] button.
and
buttons, and then
buttons, and then press the
buttons, and then press the
2
3
4
USER FUNCTIONS
01.DEFAULT SETTINGS
02.LISTS
1216
03.INITIAL SETUP
Select “COPY SETUP” with
[ENTER] button.
and
DEFAULT SETTINGS
01.GENERAL SETTINGS
02.COPY SETUP
03.FAX SETUP
Select “FINISHING” with
[ENTER] button.
and
COPY SETUP
03.IMAGE MODE
04.LIGHT/DARK
05.FINISHING
Finishing Mode 163
5
CHANGING EQUIPMENT’S SETTINGS
Select the initial finishing mode with the
then press the [ENTER] button.
and
buttons, and
5
The following finishing modes can be selected:
NONSORT, SORT, ALTERNATION and MAGAZINE SORT
FINISHING
2.SORT
3.ALTERNATION
4.MAGAZINE SORT
The initial finishing mode is set and the screen returns to the menu in step 4.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
6
7
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
164 Finishing Mode
Various List Printing
This section describes how to print the list in order to check the following information.
DEPARTMENT CODE:
The department codes which have been registered and the counter
values of each department code
FUNCTION:
The contents of the settings in this equipment
SUPPLY NOTICE:
ITU MAILBOX:
Supply information of the equipment
The box numbers and attributes of the mail boxes which have been
registered, and the registration date/time of the originals
CONFIGURATION PAGE: The setting status of the Network Printer Kit (optional)
NIC STATUS PAGE:
The NIC (Network Interface Card) information of the Network
Printer Kit (optional)
Press the [USER FUNCTIONS] button.
1
2
The “user functions mode” main screen is displayed.
Select “LISTS” with
[ENTER] button.
and
buttons, and then press the
USER FUNCTIONS
1216
01.DEFAULT SETTINGS
02.LISTS
03.INITIAL SETUP
Various List Printing 165
5
CHANGING EQUIPMENT’S SETTINGS
Select the list you want to print with the
then press the [ENTER] button.
and
buttons, and
3
LISTS
1.DEPARTMENT CODE
2.FUNCTION
3.SUPPLY NOTICE
y “SUPPLY NOTICE” is displayed only when the Fax Kit or Scanner Upgrade Kit (both
optional) is installed.
y “ITU MAILBOX” is displayed only when the Fax Kit (optional) is installed.
Network Printer Kit (optional) is installed.
The list is printed.
See the following page for the printing example of each list.
P.211 “List Print Format”
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
4
5
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
166 Various List Printing
Menu List Printing
This section describes how to print the menu list of the equipment.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “MENU LIST” with
[ENTER] button.
and
buttons, and then press the
2
USER FUNCTIONS
02.LISTS
1216
04.MENU LIST
The menu list is printed.
See the following page for the example of the menu list.
P.211 “List Print Format”
Press the [CANCEL] or [FUNCTION CLEAR] button.
The screen returns to the “user functions mode” main screen.
3
4
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
Menu List Printing 167
5
CHANGING EQUIPMENT’S SETTINGS
ROM Version Display
This section describes how to display the product version.
Press the [USER FUNCTIONS] button.
1
The “user functions mode” main screen is displayed.
Select “MACHINE REVISIONS” with
press the [ENTER] button.
and
buttons, and then
2
USER FUNCTIONS
04.MENU LIST
1216
05.TEST MODE
06.MACHINE REVISIONS
The product version of the equipment is displayed.
Press the [CANCEL] button several times or press the [FUNCTION
CLEAR] button once.
3
4
The screen returns to the “user functions mode” main screen.
Press the
(copy mode) button.
The screen returns to the “copy mode” main screen.
168 ROM Version Display
6.
TROUBLESHOOTING
This chapter describes how to deal with error messages, how to release a paper jam, how to replace a toner
cartridge and how to resolve other troubles.
Checking position of paper jams.....................................................................................................172
Paper jam behind transfer unit........................................................................................................179
Paper jams within fuser unit............................................................................................................181
Paper jams within Paper Feed Pedestal (optional).........................................................................184
Replacing Toner Cartridge...................................................................................185
Before Calling Service Technician ......................................................................192
General operation ...........................................................................................................................192
Toner-related items .........................................................................................................................193
Original/Copy paper-related items ..................................................................................................194
Image trouble ..................................................................................................................................195
6
TROUBLESHOOTING
When This Message Appears
and take a countermeasure accordingly.
Message
Meaning
Countermeasure
Misfeed in ***
This appears when an origi- Remove any jammed paper.
nal or a sheet of copy paper
is jammed at the place indi-
cated by “***”.
P.172 “Paper Jams”
Close ***
This appears when any
cover of the equipment indi-
cated by “***” is not securely
closed.
Close the cover securely.
CASSETTE * empty
Count over
This appears when the paper Set paper in the drawer.
in a drawer indicated by “***”
has run out.
P.37 “Placing paper in drawers”
The number of pages
scanned has exceeded the
maximum value (250
sheets).
Select “Print” on the LCD screen to copy
the data scanned so far. Select “Cancel
job” to delete all the data scanned so far.
Call for service
This appears when the repair Contact your service representative.
or adjustment by your ser-
vice technician is needed.
When the [8] key of the digital keys and
the [CLEAR/STOP] button are pressed
simultaneously, an error code (consisting
of a letter of the alphabet and numbers)
appears on the display. Contact your ser-
vice technician with this code.
Never attempt to repair, disassemble
or modify the equipment by yourself.
This could cause an electric shock, a fire
or serious injury. Contact your service
representative when the equipment is in
an abnormal condition or any malfunction
is found.
Time for maintenance
This appears when the main- Contact your service representative.
tenance by your service
technician is needed.
BYPASS empty
Toner is low
Paper set on the bypass tray Place paper on the bypass tray.
has run out.
P.59 “Using Bypass Tray”
There is only a little toner
remaining in the toner car-
tridge.
There is still a little toner remaining in the
toner cartridge. Do not replace the toner
cartridge until “Toner empty” appears on
the display.
y
y
The message may not appear
because the toner remaining in the
cartridge does not lie evenly.
When the message appears, it is
advisable to purchase a new
TOSHIBA-recommended cartridge to
prepare for its replacement.
170 When This Message Appears
Message
Meaning
Countermeasure
Toner not recognized
The toner cartridge is not
installed correctly.
Install the toner cartridge correctly.
mended by TOSHIBA is
being used.
tridge.
If you want to use a toner cartridge other
annoyed by this message, contact your
service representative.
P.13 “Recommended toner cartridges”
Replace the toner cartridge with a new
one.
Toner empty
The toner in the toner car-
tridge has run out.
P.185 “Replacing Toner Cartridge”
Enter the correct department code. If you
do not know the department code, contact
your administrator.
Invalid Dept.Code
The department code
entered in the department
code entering screen is not
correct.
Memory is full
The built-in memory of the
equipment has become full.
Select “Print” on the LCD screen to copy
the data scanned so far. Select “Cancel
job” to delete all the data scanned so far.
Clear paper output tray:
PRESS START KEY.
Approx. 250 sheets of paper Remove the paper from the receiving tray,
have continuously exited and and then press the [START] button. Copy-
the equipment stops copy-
ing to prevent the copied
ing resumes.
Press the [CLEAR/STOP] button to end
paper from overflowing from the copy job. “Memory clear?” appears on
the tray.
the LCD screen. Select “YES”, and then
press the [START] or [ENTER] button.
When This Message Appears 171
6
TROUBLESHOOTING
Paper Jams
Checking position of paper jams
When a jam of copying paper or original occurs in the equipment, the copying operation stops
and the following message appears on the display to indicate the positions where the paper is
jammed.
Misfeed in copier
Open side cover
of the copier.
1/ 6
Check the message, remove any paper jam, and then press the [START] button to resume
copying.
When a jam of copying paper or original occurs in the equipment, the procedure to remove the
jammed paper appears on the display. Press the
procedure.
and
buttons to scroll up and down the
Message
Misfeed in doc.feeder
Inside of the optional Reversing Automatic Document Feeder /
Automatic Document Feeder
(
P.174)
Misfeed in bypass
Misfeed in duplexer
Misfeed in copier
Bypass tray ( P.177)
Inside of the optional Automatic Duplexing Unit (
P.178)
Inside of the transfer unit (
Inside of the fuser unit (
P.179)
P.181)
Drawer of the optional Paper Feed Unit (
P.183)
P.184)
Drawer of the optional Paper Feed Pedestal (
172 Paper Jams
When paper jams occur frequently
/ Automatic Document Feeder (optional) are placed.
P.53 “Precautions for Reversing Automatic Document Feeder (optional) / Automatic Doc-
ument Feeder (optional)”
P.36 “Paper types not acceptable”
y The sizes of paper placed in the drawer or on the bypass tray are not registered into the
equipment properly.
P.45 “Preparation 3 - Registering Size of Paper Placed”
P.60 “Preparation - Registering paper size placed on bypass tray”
y More jammed paper is still remaining after the release of a paper jam.
y There is no gap between the side guides and the paper in the drawer, or the gap is too wide.
y The stack height of the paper is exceeding the indicators in the drawer.
When releasing jammed paper
Observe the following precautions when you release jammed paper:
Do not tear jammed paper.
Pull out jammed paper carefully with both hands, trying not to tear it. If you release it forcibly, the
jammed paper will be torn and it will make the release difficult. If it is torn, be sure that the torn
part is not left inside the equipment.
Do not touch the fuser unit or the metal part around the unit.
When you release paper jammed within the fuser unit, do not touch the fuser unit or the metal
part around the unit. This could cause burns, or injury to your hands if you touch the inside of the
equipment.
Do not touch the photoconductive drum.
When you release the paper jammed within the transfer unit or the fuser unit, be careful not to
touch the photoconductive drum. This could stain the copy images.
Paper Jams 173
Open the transport guide.
4
5
Raise the guide plate under the transport guide, and then release
the original jammed under the guide plate.
Close the transport guide, and then close the upper cover.
6
7
When the Automatic Document Feeder is used, the releasing procedure ends here.
When the Reversing Automatic Document Feeder is used, go on to the following
procedure.
Open the Reversing Automatic Document Feeder.
Paper Jams 175
6
TROUBLESHOOTING
Open the reverse cover, and then remove the original.
8
9
Close the Reversing Automatic Document Feeder slowly.
Raise the lever, and then open the upper cover.
10
176 Paper Jams
6
TROUBLESHOOTING
Release the jammed paper.
3
Be sure not to touch the photoconductive drum when releasing the jammed paper.
Open the transport guide of the paper feeding area and check if any
paper is jammed under this guide. Clear the paper if there is any.
4
5
Close the transfer unit and the side cover.
180 Paper Jams
Paper jams within fuser unit
y Be careful not to let your fingers be caught between the equipment and the side cover.
This could injure you.
y Do not touch the fuser unit or the metal part around the unit.
This could cause burns, or injury to your hands if you touch the inside of the equipment.
Open the side cover, and then lay down the transfer unit. Then
press down the two fuser pressure release levers (green) until they
come to a stop.
1
Press down the levers fully until they stop.
Open the transport guide while holding the knob (A).
2
A
Paper Jams 181
6
TROUBLESHOOTING
Release the jammed paper.
Pull the jammed paper up or down as shown below depending on the position of the
paper.
3
Be sure not to touch the photoconductive drum when releasing the jammed paper.
Pulling it up
Pulling it down
Return the transport guide to its original position, and then close
the transfer unit and the side cover.
4
182 Paper Jams
Replacing Toner Cartridge
When the toner cartridge runs out of toner, the following message appears on the display.
Toner empty
Open front cover.
1/ 3
Then, replace the cartridge with a new one.
When the toner cartridge runs out of toner, the procedure to replace the toner cartridge appears
on the display. Press the and buttons to scroll up and down the procedure.
Never attempt to incinerate toner cartridges. This could cause an explosion.
y Before inserting a new toner cartridge, check the product name of the cartridge. If you can
see “T-1640”, this cartridge is usable.
y Do not dispose of used toner cartridges. Contact your service representative.
y Do not touch the parts on the circuit board mounted on the toner cartridge because they may
be damaged.
Replacing Toner Cartridge 185
6
TROUBLESHOOTING
Recommended toner cartridges
To assure an optimal printing performance, we recommend that you use TOSHIBA toner cartridges.
If you use a TOSHIBA-recommended toner cartridge, you can utilize the following two check functions of
this equipment:
Cartridge detecting function: This function checks if the toner cartridge is correctly installed and notifies
you if it is not.
Toner-remaining check function: This function notifies you when there is little toner remaining in the
cartridge, as well as notifying it to your service representative automatically by the remote service.
Any copying or printing operation is available even if you are using a toner cartridge other than the one
we recommend. In that case, however, the equipment cannot detect whether the toner cartridge is
installed or not and therefore an error message “Toner not recognized” appears on the LCD screen, even
if the toner cartridge is correctly installed. You cannot utilize the toner remaining check function and the
remote service function notifying your service representative automatically either.
If you are using a toner cartridge other than the one we recommend and you feel annoyed by this mes-
sage, contact your service representative. Your service technician will cancel the cartridge detecting func-
tion set by default. Remember once this function has been cancelled, you will not be able to utilize the two
functions mentioned above even if you change the cartridge to the one we recommend.
186 Replacing Toner Cartridge
Open the front cover.
1
2
Hold down the green lever.
Pull out the toner cartridge.
3
Never attempt to incinerate toner cartridges. This could cause an explosion.
Replacing Toner Cartridge 187
6
TROUBLESHOOTING
Shake the new toner cartridge well to loosen the toner inside.
4
5
6
Pull out the seal in the direction of the arrow.
Insert the toner cartridge along the rail.
y Before inserting the toner cartridge, check if the green lever is raised and raise it if
not.
y Insert it until you hear a click sound.
188 Replacing Toner Cartridge
Clean the charger.
7
Hold the cleaning knob of the charger and pull it out toward you carefully until it comes to
a stop. Then reinsert it in its original position carefully. Repeat this procedure two or three
times.
Check if the cleaning knob is fully inserted after cleaning.
Open the side cover.
8
9
Pull the transfer unit toward you carefully to lay it down while hold-
ing up the green lever.
Replacing Toner Cartridge 189
6
TROUBLESHOOTING
Remove the transfer charger cleaner from the front pocket of the
transfer unit.
10
11
Wipe the transfer charger wire with the transfer charger cleaner.
(1) Insert the transfer charger cleaner into the front end of the transfer charger.
(2) Push the cleaner onto the front wall, and then check if the cleaner pad has contacted
with the transfer charger wire.
(3) Clean the wire from its front end to the other end in two reciprocating motions.
(4) Remove the cleaner from the front end of the transfer charger after cleaning.
Return the transfer charger cleaner into the cleaner pocket, and
then close the transfer unit.
12
13
Close the side cover.
190 Replacing Toner Cartridge
Close the front cover.
The equipment starts supplying toner.
14
Replacing Toner Cartridge 191
6
TROUBLESHOOTING
Before Calling Service Technician
When you encounter trouble using this equipment, check the items listed below.
General operation
Phenomenon
Usual cause
Countermeasure
The equipment does not
operate at all.
The power cable is not
plugged in securely.
Plug in the power cable securely.
The weekly timer functions
and the equipment is in the
sleep mode.
Press any button on the control panel.
The equipment does not
operate even when you press screen.
any of the buttons.
A message appears on the
termeasure accordingly.
P.170 “When This Message Appears”
Press the [ENERGY SAVER] button to
cancel this mode.
The equipment is in the
energy saving mode.
P.34 “Saving energy when not in use -
Energy saving mode -”
When the use of the equip-
ment is managed under
department management,
and the department code
has not been entered.
It has been a short time
since the power was turned
ON.
Enter your department code.
P.33 “Preparation 1 - Turning Power
ON”
P.141 “Department Code”
Wait for the completion of warm-up and
then try again.
Scanning stops in the mid-
dle. (“Count over” appears on scanned has exceeded the
the display.)
The number of pages
Select “Print” on the LCD screen to copy
the data scanned so far. Select “Cancel
job” to delete all the data scanned so far.
Select “Print” on the LCD screen to copy
the data scanned so far. Select “Cancel
job” to delete all the data scanned so far.
maximum value.
Scanning stops in the mid-
dle. (“Memory is full” appears equipment has become full.
on the display.)
The built-in memory of the
Copying stops in the middle.
(“Clear paper output tray:
PRESS START KEY.”
Approx. 250 sheets of paper Remove the paper from the receiving tray,
have continuously exited and and then press the [START] button. Copy-
the equipment stops copy-
ing to prevent the copied
ing resumes.
Press the [CLEAR/STOP] button to end
appears on the display.)
paper from overflowing from the copy job. “Memory clear?” appears on
the tray.
the LCD screen. Select “YES”, and then
press the [START] or [ENTER] button.
The equipment automatically enters into
this mode when a specified period of time
has passed since its last use. Copying is
enabled.
“Saving energy” appears on
the display.
The equipment is in the low
power mode.
“Sleep mode” appears on the The equipment is in the
display. sleep mode.
The equipment automatically enters into
this mode when a specified period of time
has passed since its last use. Warm-up
pressed. Copying is enabled when the
warm-up has finished.
Copy functions cannot be set. Other functions that cannot
Some functions cannot be combined set
together.
P.209 “Copying Function Combination
Matrix”
be set simultaneously with
copy functions have been
set.
192 Before Calling Service Technician
Phenomenon
Usual cause
Countermeasure
The department management Any department code other
department management when it has
been already enabled, enter the master
code in the department code entry
screen, otherwise the department man-
agement menu cannot be displayed.
P.141 “Department Code”
menu does not appear even
though “DEPARTMENT
CODE” is selected.
than the master code has
been entered in the depart-
ment code entry screen.
Toner-related items
Phenomenon
Usual cause
Countermeasure
“Toner is low” appears on the There is only a little toners
There is still some toner in the toner car-
tridge. Do not replace the toner cartridge
until “Toner empty” appears.
display.
remaining in the toner car-
tridge.
“Toner empty” appears on the The toner in the toner car-
Replace the toner cartridge with a new
one.
display.
tridge has run out.
“Toner not recognized”
appears on the display.
The toner cartridge is not
installed. Or it is not installed
correctly.
Install the toner cartridge correctly.
A toner cartridge not recom- Use a TOSHIBA-recommended toner car-
mended by TOSHIBA is
being used.
tridge. If you use a toner cartridge other
than the one we recommend and you feel
annoyed by this message, contact your
service representative.
P.13 “Recommended toner cartridges”
Contact your service representative.
“Toner is low” does not
appear on the display,
although toner is nearly
empty.
The toner-remaining check
function has been disabled
since the purchase of the
equipment.
The equipment does not
become ready for copying
after the toner cartridge is
inserted.
The toner cartridge inserted
is not usable for this equip-
ment.
Check the product name of the toner car-
tridge. If you can see “T-1640”, this car-
tridge is usable.
Before Calling Service Technician 193
6
TROUBLESHOOTING
Original/Copy paper-related items
Phenomenon
Usual cause
Countermeasure
An original jams.
An original not acceptable for Check if the original is acceptable for the
the equipment is being used. equipment.
P.53 “Precautions for Reversing Auto-
matic Document Feeder (optional) / Auto-
matic Document Feeder (optional)”
Copy paper jams.
Copy paper not acceptable
for the equipment is being
used.
the equipment.
The size of the copy paper in Register the size of the placed copy paper
the drawer or on the bypass properly.
tray is not registered prop-
erly in the equipment.
P.45 “Preparation 3 - Registering Size
of Paper Placed”
P.60 “Preparation - Registering paper
size placed on bypass tray”
Jammed paper is located in
a place you cannot see eas- recheck the position where the paper jam
ily.
has occurred.
P.172 “Paper Jams”
There is no gap between the Adjust the gap between the side guides
side guides and paper in the and the paper properly.
drawer. Or the gap is too
wide.
P.37 “Placing paper in drawers”
Multiple feeding occurs.
Paper is clinging to each
other.
Fan the paper well and place it again.
194 Before Calling Service Technician
Image trouble
Phenomenon
Usual cause
Countermeasure
The density of the copy
image is light.
Toner has run out.
“Toner empty” appears on the display
when toner has run out. Replace the toner
cartridge if the message appears.
P.185 “Replacing Toner Cartridge”
Make the density darker if you use the
manual copy density mode. Or use the
automatic copy density mode.
The copy density is set
lighter.
The transfer charger wire is
dirty.
Clean the transfer charger wire.
P.200 “Cleaning transfer charger”
Make the density lighter if you use the
manual copy density mode. Or use the
automatic copy density mode.
The density of the copy
image is dark.
The copy density is set
darker.
The copied image is stained. The Reversing Automatic
Document Feeder (optional)
/ Automatic Document
Feeder (optional) or the
Platen Cover (optional) is not
lowered fully.
Lower them fully to block outside light.
The original glass, platen
sheet, scanning area or
guides are dirty.
Clean them.
P.198 “Daily Inspection”
The copy density is set
darker.
Make the density lighter if you use the
manual copy density mode. Or use the
automatic copy density mode.
A highly transparent original Place a blank sheet of paper, the same
is used.
size as the original or larger, over the orig-
inal.
The copy image is fogged.
There is a slight gap
between the original glass
and the original.
Lower the Platen Cover (optional) or the
Reversing Automatic Document Feeder
(optional) / Automatic Document Feeder
(optional) fully so that the original will con-
tact with the original glass.
The copy paper is damp.
Replace with dry copy paper.
The density level of the copy
image is uneven in a horizon- dirty.
tal direction.
The transfer charger wire is
Clean the transfer charger wire.
P.200 “Cleaning transfer charger”
Before Calling Service Technician 195
6
TROUBLESHOOTING
Phenomenon
Usual cause
Countermeasure
The copy image is partially
missing.
The size or direction of the
copy paper and the original,
or the reproduction ratio is
not set properly.
original or set the reproduction ratio suit-
able to the copy paper size.
The margin for binding is too Adjust the image shift value again.
wide.
P.88 “Shifting Paper to Make Margin -
IMAGE SHIFT -”
The copy image has black
streaks in a horizontal direc-
tion.
The scanning area or guides Clean them.
are stained.
P.198 “Daily Inspection”
The charger is dirty.
Clean the charger.
P.199 “Cleaning charger”
The copy image has white
streaks in a horizontal direc-
tion.
The transfer charger wire is
dirty.
Clean the transfer charger wire.
P.200 “Cleaning transfer charger”
196 Before Calling Service Technician
7.
MAINTENANCE AND INSPECTION
This chapter describes how to clean this equipment to ensure you get the best possible copy performance.
Daily Inspection ....................................................................................................198
Cleaning charger.............................................................................................................................199
Cleaning transfer charger................................................................................................................200
7
MAINTENANCE AND INSPECTION
Daily Inspection
We recommend a weekly cleaning of the following items to assure you the best scanning perfor-
mance:
y Be sure not to scratch the parts to be cleaned.
y Do not use solvent such as thinner or benzene to clean machinery. This could cause defor-
mation or tarnishing.
y When using chemical cleaning pads, observe the precautions pertaining to the product.
2
3
4
1
1. Scanning area
Wipe with a sheet of soft dry cloth or soft cloth dampened in water and squeezed tightly. Do
not use alcohol or solvent.
2. Original glass
3. Guides
4. Platen sheet
Clean in the following procedure according to the level of staining:
-
-
-
Wipe with a soft dry cloth.
Wipe with a soft cloth dampened in water and squeezed tightly.
Wipe with a soft cloth dampened in alcohol and squeezed tightly, and then wipe with a
soft dry cloth.
-
Wipe with a soft cloth dampened in diluted mild detergent and squeezed tightly. Then
wipe with a soft cloth dampened in water and squeezed tightly. Then wipe with a soft dry
cloth.
198 Daily Inspection
Cleaning charger
If the inside of the charger is dirty, staining may appear on the copied image. Clean the charger
following the procedure below.
Open the front cover.
1
Clean the charger.
Hold the cleaning knob of the charger and pull it out toward you carefully until it comes to
a stop. Then reinsert it in its original position carefully. Repeat this procedure two or three
times.
2
Check if the cleaning knob is fully inserted after cleaning.
Close the front cover.
3
Daily Inspection 199
7
MAINTENANCE AND INSPECTION
Cleaning transfer charger
When the transfer charger wire is dirty, white steaks or unevenness of the density may appear
on copied images, or the density of the whole image may be lowered. Clean the transfer charger
wire following the procedure below.
Be careful not to let your fingers be caught between the equipment and the side cover.
This could injure you.
Open the side cover.
1
Pull the transfer unit toward you carefully to lay it down while hold-
ing up the green lever.
2
200 Daily Inspection
Remove the transfer charger cleaner from the front pocket of the
transfer unit.
3
4
Wipe the transfer charger wire with the transfer charger cleaner.
(1) Insert the transfer charger cleaner into the front end of the transfer charger.
(2) Push the cleaner onto the front wall, and then check if the cleaner pad has contacted
with the transfer charger wire.
(3) Clean the wire from its front end to the other end in two reciprocating motions.
(4) Remove the cleaner from the front end of the transfer charger after cleaning.
Return the transfer charger cleaner into the cleaner pocket, and
then close the transfer unit.
5
6
Close the side cover.
Daily Inspection 201
7
MAINTENANCE AND INSPECTION
202 Daily Inspection
8.
SPECIFICATIONS AND OPTIONS
e-STUDIO165/205 Specifications.........................................................................204
Copying Function Combination Matrix...............................................................209
Department code list .......................................................................................................................211
Mailbox list ......................................................................................................................................214
Menu list..........................................................................................................................................217
Function list.....................................................................................................................................212
Supply notice list .............................................................................................................................213
8
SPECIFICATIONS AND OPTIONS
e-STUDIO165/205 Specifications
Model name
DP-1650/2040
Type
Desktop type
Original glass
Fixed
Printing (copying) system
Developing system
Fusing method
Indirect electrophotographic method
2-component magnetic brush developing
2 halogen lamps
Photosensor type
Original scanning system
OPC
Flat surface scanning system
(When the Reversing Automatic Document Feeder / Automatic
Document Feeder is installed: Fixed scanning system by feeding
the original)
Original scanning sensor
Scanning light source
Linear CIS sensor
LED
Resolution
Scanning
600 dpi x 600 dpi
Writing
2400 dpi x 600 dpi (Smoothing process)
Acceptable originals
Acceptable original size
Acceptable copy
paper size
Sheets, books and 3-dimensional objects
Max. A3
Drawer
Bypass
A3, A4, A4-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, COMP,
13"LG
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R,
COMP, 13"LG
64 - 80 g/m2
Acceptable copy
paper weight
Drawer
Bypass
64 - 80 g/m2 (for continuous feed)
50 - 163 g/m2 (for single feed)
64 - 80 g/m2 (When the Automatic Duplexing Unit is used.)
Approx. 25 seconds
Warm-up time
First copy time (A4 portrait)
Continuous copy speed
Multiple copying
7.6 seconds or less
See
P.205 “Continuous copying speed”
Up to 999 copies (digital key entry)
Excluded image
width
Copy
Leading edge: 3.0±2.0 mm, Trailing edge: 3.0±2.0 mm,
Both edges: 2.0±2.0 mm
Printer
Leading edge: 5.0±2.0 mm, Trailing edge: 5.0±2.0 mm,
Both edges: 5.0±2.0 mm
Reproduction ratio
Paper supply
Actual size 100±0.5%
Zoom
25 - 200% (in 1% increments)
250 sheets (80 g/m2)
Drawer
100 sheets (80 g/m2)
Bypass
Toner density adjustment
Exposure control
Magnetic auto-toner system
Automatic plus manual selection from 7 exposure steps
Temperature: 10 º - 30 ºC, Humidity: 20 - 85% (No condensation)
220 - 240 V±10%, 8 A (50/60 Hz),
Environment (for normal use)
Power requirements
127 V±10%, 12 A (50/60 Hz) (for Saudi Arabia 100 V version only)
1.6 kW or less (including optional equipments),
1.5 kW or less (including optional equipments) (for Saudi Arabia
100 V version only)
Power consumption
Dimensions (equipment only)
Weight
600 mm (W) x 658.6 mm (D) x 462.5 mm (H)
Approx. 32.5 kg
Space occupied (equipment only)
Storage capacity
948 mm (W) x 658.6 mm (D)
Max. 250 sheets or until the memory is full (TOSHIBA’s own chart)
Approx. 250 sheets (64 g/m2)
Loading capacity for the receiving
tray
y These specifications vary depending on the copying conditions and the environment.
y Specifications and appearance are subject to change without notice in the interest of product
improvement.
204 e-STUDIO165/205 Specifications
Continuous copying speed
sheets/min.
e-STUDIO205
Paper size
Feeder
e-STUDIO165
A4, A5-R*1, B5, LT, ST-R*1
Drawer
16
16
20
20
Bypass tray
Drawer
A4-R, B5-R, LT-R
B4, FOLIO, LG, COMP, 13"LG
A3, LD
15.5
15.5
13
15.5
15.5
13
Bypass tray
Drawer
Bypass tray
Drawer
13
13
11
11
Bypass tray
11
11
*1 A5-R and ST-R can be placed only on the bypass tray.
y The values above are measured when originals are set on the original glass, 100% and non-
sort multiple copies are made.
y TOSHIBA-recommended paper is used for the values of the specifications above.
y The bypass copying speed is as listed above when specifying the paper size.
y This specification varies depending on the copying conditions and the environment.
e-STUDIO165/205 Specifications 205
8
SPECIFICATIONS AND OPTIONS
Specifications of Options
Reversing Automatic Document Feeder
Model name
Copy sides
MR-3019
1-side, Duplex
100 originals (50 - 80 g/m2) or 16 mm or less in height (more than 80 g/m2)
Number of originals
(A4)
Feeding speed
45.5 - 182 mm/s
Acceptable originals
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R, COMP (A5
and ST size are not acceptable.)
1-sided original: 50 - 127 g/m2, 2-sided original: 50 - 127 g/m2
Power supplied from the equipment
600 mm (W) x 513 mm (D) x 135 mm (H)
Approx. 11.5 kg
Paper weight
Power source
Dimensions
Weight
Power consumption
33 W max.
Automatic Document Feeder
Model name
Copy sides
MR-2017
1-side
100 originals (50 - 80 g/m2) or 16 mm or less in height (more than 80 g/m2)
Number of originals
(A4)
Feeding speed
45.5 - 182 mm/s
Acceptable originals
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R, COMP (A5
and ST size are not acceptable.)
50 - 127 g/m2
Paper weight
Power source
Dimensions
Power supplied from the equipment
600 mm (W) x 513 mm (D) x 135 mm (H)
Approx. 11.0 kg
Weight
Power consumption
30 W max.
Automatic Duplexing Unit
Model Name
MD-0103
Acceptable Paper
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R, COMP,
13"LG
64 - 80 g/m2
Power Source
Weight
Approx. 1.2 kg
Paper Feed Unit
Model name
MY-1027
Acceptable paper size
A3, A4, A4-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, COMP, 13"LG (Non-
standard sizes are not acceptable.)
64 - 80 g/m2
Paper weight
250 sheets (80 g/m2)
Maximum capacity
Dimensions
Weight
530 mm (W) x 577 mm (D) x 125 mm (H)
Approx. 5.0 kg
206 Specifications of Options
Paper Feed Pedestal
Model name
KD-1013
Acceptable paper size
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R, COMP (A5,
ST and non-standard size are not acceptable.)
64 - 80 g/m2
Paper weight
550 sheets (80 g/m2)
Maximum capacity
Dimensions
Weight
623 mm (W) x 657 mm (D) x 367 mm (H)
Approx. 26.0 kg
Drawer Module
Model name
MY-1028
Acceptable paper size
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R, COMP (A5,
ST and non-standard size are not acceptable.)
64 - 105 g/m2
Paper weight
Maximum capacity
Weight
550 sheets (80 g/m2)
Approx. 4.0 kg
TOSHIBA-recommended paper is used for the values above. Specifications and appearance are
subject to change without notice in the interest of product improvement.
Specifications of Options 207
List Print Format
Department code list
DEPARTMENT CODE LIST
PAGE
:
:
:
:
001
TIME
10-04-2006
09:30
TEL NUMBER
NAME
XXX-XXX-XXXX
XXXXXXXXXX
DEPT NBR
NAME
DEPT CODE
COPY PGS
TX PGS
RX PGS
Print PGS
D
D
D
D
01
02
03
99
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXX
XXXXX
XXXXX
XXXXX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
List Print Format 211
8
SPECIFICATIONS AND OPTIONS
Function list
XXXXX XXXXXX
XXXXX XXXXXX
XXXXXXXXXXX
XXXXX
FUNCTION LIST
PAGE
:
:
:
:
001
TIME
10-04-2006
09:30
TEL NUMBER
NAME
XXX-XXX-XXXX
XXXXXXXXXX
:
QWERTY
112MB
RECOVERY TX
TTI
:
OFF
ON
KEYBOARD TYPE
:
:
AVAILABLE MEMORY
SEND AFTER SCAN
ACCOUNT CODE
SEPARATOR PAGE
SECURE RX
MEMORY RX
REDUCTION
DISCARD
:
:
:
:
:
:
:
:
:
OFF
OFF
OFF
OFF
ON
GENERAL SETTING
DRAWER SIZE
:
:
:
A4
DRAWER
BYPASS
1
COPY
ON
WALKUP SCREEN
TIMERS
OFF
OFF
OFF
:
:
:
:
45SEC
15MIN
15MIN
OFF
PRIVILEGED RX
RTI
AUTO CLEAR
AUTO POWER SAVE
AUTO SLEEP
WEEKLY TIMER
SPEAKER VOLUME
ALARM VOLUME
KEY TOUCH VOLUME
RINGER VOLUME
MONITOR VOLUME
REPORTS & LIST
JOURNAL
:
:
:
:
0
1
4
4
:
:
TX & RX
ON
MANUAL OUTPUT
AUTO
COMMUNICATION REPORT
DOCUMENT TX
MEMORY TX
:
:
:
:
:
:
ON ERROR
ON ERROR (IMAGE)
ON ERROR (IMAGE)
ON ERROR
COPY SETUP
MENU CUSTOMIZE
APS/AMS
MULTI TX
:
:
:
:
:
FINISHING
APS
MULTI POLL
ON ERROR (IMAGE)
ON ERROR (IMAGE)
:ON ERROR (IMAGE)
RELAY ORIGINATOR
RELAY STATION
RELAY DESTINATION
RECEPTION LIST
LOCAL MAILBOX
REMOTE MAILBOX
RELAY STATION
TEXT/PHOTO
AUTO
IMAGE MODE
LIGHT/DARK
FINISHING
NON SORT
:
:
:
OFF
OFF
ON
FAX SETUP
:
:
:
:
:
:
:
OFF
3MIN
ON
LINE MONITOR
RECEIVE INTERVAL
ECM
STD
AUTO
MF
:
:
:
OFF
DOCUMENT MODE
LIGHT/DARK
DIAL TYPE
REMOTE SERVICE
NO JOB
REMOTE ACCESS
DOWNLOAD FIRMWARE
RDC PASSWORD
ACCESS DIGIT
REDIAL MODE
INTERVAL
:
:
:
:
:
:
1MIN
1
:
:
245
150
TOTAL PAGE
COUNTER
SCAN
PRINT
AUTO
1
RECEPTION MODE
RING DELAY
MEMORY TX
SECURITY TX
ON
OFF
212 List Print Format
Supply notice list
SUPPLY NOTICE FORM
SETUP INFORMATION
D E S T I N AT I O N S E T U P
:
:
X X X - X X X - X X X X
D AT E
&
T I M E
1 0 - 0 4 - 2 0 0 6
0 9 : 3 0
C U S T O M E R N U M B E R
S H I P T O N A M E
:
X X X - X X X - X X X X
X X X X X X X X X X
X X X X X X X X X X
X X X X X X X X X X
X X X - X X X - X X X X
:
S H I P T O A D D R E S S
C O N TA C T N A M E
:
:
C O N TA C T T E L N U M B E R
:
e-STUDIO 165/205 Series
MACHINE NAME
:
:
:
:
XXXXXXXXXX
XXX-XXX-XXXX
XXXX
FAX NUMBER
TOTAL PRINTED PAGES
TOTAL SCANNED PAGES
XXX
List Print Format 213
8
SPECIFICATIONS AND OPTIONS
Mailbox list
MAILBOX/RELAY BOX REPORT
:
:
:
:
001
PAGE
10-04-2006
09:30
TIME
XXX-XXX-XXXX
XXXXXXXXXX
TEL NUMBER
NAME
MAILBOX
BOX NBR
TYPE
PGS FILE NBR DATE
TIME
FROM
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
CONFIDENTIAL BOX
CONFIDENTIAL BOX
BULLETIN BOARD
BULLETIN BOARD
X
X
X
X
XX
XX
XX
XX
XX
XX
XX
XX
XX:XX
XX:XX
XX:XX
XX:XX
XXXX
XXXX
XXXX
XXXX
RELAY
RELAY BOX
END STATION
REPLY TO NUMBER
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
ABB
001
002
ABB.
003
GROUP
1111
XXXXXXXXXX
214 List Print Format
Configuration page list
CONFIGURATION PAGE
S/N
:
:
XXXXXXXXXX
XXXXXXXXXXX
TIME
:
'06-04-10 09:30
F/W Ver.
GENERAL
MEMORY SIZE
:
:
256MB
OPTIONAL FUNCTIONAL KIT
NOT INSTALLED
NETWORK SETTING
GENERAL PRODUCT
GENERAL
ETHERNET SPEED/DUPLEX MODE
:
10BASE FULL
NETWORK
TCP/IP
ADDRESS MODE
IP ADDRESS
:
:
:
:
DYNAMIC
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
SUBNET MASK
DEFAULT GATEWAY
0.
0.
0.
0
IPX/SPX
ENABLE IPX/SPX
FRAME TYPE
APPLE TALK
:
:
ENABLE
AUTO SENSE
ENABLE APPLE TALK
DEVICE NAME
:
:
:
DISABLE
XXXXXXXXXXXX
*
DESIRED ZONE
SESSION
DNS SESSION
ENABLE DNS
:
:
:
ENABLE
PRIMARY DNS SERVER ADDRESS
SECONDARY DNS SERVER ADDRESS
0.
0.
0.
0.
0.
0.
0
0
DDNS SESSION
ENABLE DDNS
HOST NAME
:
:
:
ENABLE
XXXXXXXXXXXX
DOMAIN NAME
NETWARE SESSION
ENABLE BINDERY
:
:
:
:
:
ENABLE
ENABLE
ENABLE NDS
CONTEXT
TREE
SEARCH ROOT
BONJOUR SESSION
ENABLE BONJOUR
LINK LOCAL HOST NAME
:
:
ENABLE
MFP 00000376
List Print Format 215
8
SPECIFICATIONS AND OPTIONS
NIC status page list
Unit Serial No
: XXXXXXXX
Network Address : XX;XX;XX;XX;XX;XX
Network Topology : Ethernet
Connector: RJ45
Network Speed
: auto (default)
Novell Network Information
Print Server Name
Password Defined
enabled
XXXXXXXXXXXX
:
:
Search Root not defined
Directory Services Tree not defined
Directory Service Context not defined
Scan Rate
Frame Type
: 5
: Auto Sense
TCP/IP Network Information
IP Address
Subnet Mask
enabled
:
:
:
:
:
:
:
:
XX . XXX . XXX . XX
XXX . XXX . X .
XX . XXX . XXX .
X
X
Default Gateway
Primary DNS Server
DNS Name
Host Name
Primary WINS Server
NetBios Name
XXX . XX . XXX . XX
XXXXXXXXXXXX
XXX . XX . XXX . XX
XXXXXXXXXXXX
IPP Network Information
I n t e r n e t P r i n t i n g P r o t o c o l
enabled
X X X X X X X X X X
:
AppleTalk Network Information
disabled
Novell Connection Information
Couldn't attach to server
AppleTalk Connection Information
AppleTalk Printer Name: XXXXXXXXXXXX
Raw Socket Connection Information
Port Number: 9100
216 List Print Format
Menu list
MENU LIST (PROGRAM)
PAGE
:
:
:
:
001
TIME
10-04-2006
09:30
TEL NUMBER
NAME
XXX-XXX-XXXX
XXXXXXXXXX
01.DEFAULT SETTINGS
01.GENERAL SETTING
01.DRAWER SIZE
04.REPORT
01.JOURNAL
01.MANUAL OUTPUT
&
LIST
02.WALKUP SCREEN
03.TIMERS
02.AUTOMATIC JOURNAL
02.COMMUNICATION REPORT
01.TX REPORT
04.WEEKLY TIMER
05.SPEAKER VOLUME
06.DEPARTMENT CODE
02.MEMORY-TX REPORT
03.MULTI-ADD REPORT
04.MULTIPOLL REPORT
05.RELAY ORIGINATOR REPORT
06.RELAY STATION REPORT
07.RELAY END REPORT
03.RECEPTION LIST
02.COPY SETUP
01.MENU CUSTOMIZE
02.APS/AMS
03.IMAGE MODE
04.LIGHT/DARK
05.FINISHING
01.LOCAL MAILBOX LIST
02.REMOTE MAILBOX LIST
03.RELAY RECEPTION LIST
03.FAX SETUP
01.LINE MONITOR
02.RECEIVE INTERVAL
03.ECM
05.REMOTE SERVICE
01.REMOTE ACCESS
02.DOWNLOAD FIRMWARE
03.RDC PASSWORD
04.SUPPLY NOTICE
04.DOCUMENT MODE
05.DIAL TYPE
06.REDIAL MODE
07.RECEPTION MODE
08.MEMORY TX
09.SEQURITY TX
10.COVER SHEET
11.RECOVERY TRANSMIT
12.TTI
02.LISTS
1. DEPARTMENT CODE
2. FUNCTION
3. SUPPLY NOTICE
4. ITU MAILBOX
5. CONFIGURATION PAGE
6. NIC STATUS PAGE
13.SEND AFTER SCAN
14.ACCOUNT CODE
15.SEPARATOR PAGE
16.SECURE RX
17.MEMORY RX
18.REDUCTION
19.DISCARD
20.PRIVILEGED RX
21.RTI
List Print Format 217
8
SPECIFICATIONS AND OPTIONS
218 List Print Format
INDEX
DRAWER button/lamps ................................31
Numerics
A
APS / AMS ............................................... 157
Arrow buttons ............................................. 31
Automatic copy density mode ....................... 80
E
B
Before calling service technician ................. 192
C
Copy menu ................................................ 82
Copy mode main screen .............................. 32
Interrupt copy ..............................................58
Language .................................................122
D
DATA lamp ................................................ 31
Date and time ........................................... 119
Date and time display ................................ 121
Date format .............................................. 121
Default settings ........................................... 68
M
MAGAZINE SORT .......................................86
Making copies .............................................55
Making margin ............................................88
Manual paper selection ................................70
INDEX 219
Maximum number of originals scanned in
Message .................................................. 170
Message area ............................................. 32
S
Specifications of options .............................206
START button .............................................30
O
ORIGINAL button/lamps .............................. 31
Original glass ............................................. 26
P
Paper exit stopper ....................................... 26
Paper jam (Automatic Duplexing Unit) ......... 178
Paper jam (bypass tray) ............................. 177
Paper jam (Paper Feed Unit) ...................... 183
Paper jam
Placing originals ...................................50, 54
Placing paper in the drawers ..................37, 41
Platen Cover .............................................. 24
Platen sheet ............................................... 27
Precautions for
V
W
R
XY ZOOM .......................................... 83, 109
Receiving tray ............................................. 27
Recommended paper .................................. 36
Recommended toner cartridge .............13, 186
Registering paper size placed on bypass tray 60
Z
Zooming in/out copy image ...........................74
220 INDEX
DP-1650/2040
OME06003100
|
Zebra Technologies Zebra Xi4tm User Manual
Trion Air Boss Dc 4m User Manual
Sony Bravia Kdl 20s2020 User Manual
Siemens Sipart Ps2 6dr52xx User Manual
Samsung Aw09f2tbb User Manual
Royal Sovereign Arp 9011tl User Manual
Panasonic Dp 2310 User Manual
LG LT340HBU User Manual
JVC DLA G150CLU User Manual
CRAFTSMAN 358.350180 User Manual