Toshiba Air Conditioner Rav Sp1400ut E User Manual

FILE NO. A03-013

SERVICE MANUAL

<OWNER’S MANUAL/INSTALLATION MANUAL>

SPLIT TYPE

RAV-SP1100UT-E

RAV-SP560AT-E, RAV-SP800AT-E

RAV-SP1100AT-E, RAV-SP1400AT-E

R410A

The type of all the indoor units described in this Service Manual is a new model, RAV-SP1100UT-E only.

For the other indoor units to be combined, refer to the Service Manuals for the following models.

Indoor unit

Service Manual No.

A02-013

A03-003

A03-007

A03-015

A02-013

RAV-SM560UT-E

RAV-SM800UT-E

RAV-SM1400UT-E

RAV-SM561BT-E

RAV-SM801BT-E

RAV-SM1101BT-E

RAV-SM1401BT-E

RAV-SM561CT-E

RAV-SM801CT-E

RAV-SM1101CT-E

RAV-SM1401CT-E

RAV-SM560KRT-E

RAV-SM800KRT-E

4-way Air Discharge Cassette type

Concealed Duct type

Under Ceiling type

High wall type

PRINTED IN JAPAN, Feb.,2004 ToMo

Indoor Unit (4-Way Air Discharge Cassette Type) ––––––––––––––––––––––––

RAV-SP1100UT-E

OWNWE’S MANUAL

ACCESSORIES (SOLD SEPARATELY) ...............................4

PRECAUTIONS FOR SAFETY ............................................4

PARTS NAME .......................................................................6

PARTS NAME OF REMOTE CONTROLLER .......................7

CORRECT USAGE ...............................................................9

AUTOMATIC OPERATION (Auto Changeover) ................10

ADJUSTMENT OF WIND DIRECTIONd ............................11

TIMER OPERATION ...........................................................12

MAINTENANCE..................................................................14

AIR CONDITIONER OPERATIONS AND PERFORMANCE ...15

RE-INSTALLATION ............................................................16

TROUBLES AND CAUSES ................................................16

INSTALLATION MANUAL

Accessory parts and Parts to be procured locally ........18 5 ELECTRICALWORK...................................................30

1 PRECAUTIONS FOR SAFETY....................................19 6 TEST RUN ...................................................................33

2 SELECTION OF INSTALLATION PLACE ...................21 7 TROUBLESHOOTING .................................................34

3 DRAIN PIPINGWORK .................................................26 8 MAINTENANCE...........................................................35

4 REFRIGERANT PIPING AND EVACUATING..............28

Outdoor Unit –––––––––––––––––––––––––––––––––––––––––––––––––––––––––

RAV-SP560AT-E, RAV-SP800AT-E

INSTALLATION MANUAL

1 PRECAUTIONS FOR SAFETY....................................36 5 EVACUATING...............................................................45

2 ACCESSORY AND REFRIGERANT ...........................37 6 ELECTRICALWORK...................................................47

3 SELECTION OF INSTALLATION ................................38 7 FINAL INSTALLATION CHECKS ................................48

4 REFRIGERANT PIPING ..............................................43

RAV-SP1100AT-E, RAV-SP1400AT-E

INSTALLATION MANUAL

1 PRECAUTIONS FOR SAFETY....................................50 5 EVACUATING...............................................................58

2 ACCESSORY AND REFRIGERANT ...........................51 6 ELECTRICALWORK...................................................60

3 SELECTION OF INSTALLATION ................................52 7 FINAL INSTALLATION CHECKS ................................61

4 REFRIGERANT PIPING ..............................................56

Accessories ––––––––––––––––––––––––––––––––––––––––––––––––––––

OWNER’S MANUAL

REMOTE CONTROLLER FOR AIR CONDITIONER (SPLITTYPE)

WEEKLYTIMER FOR AIR CONDITIONER (SPLITTYPE)

REMOTE CONTROLLER FOR AIR CONDITIONER

TCB-AX21U (W)-E.......................................... 63

RBC-EXW21E................................................. 72

RBC-AS21E .................................................... 78

INSTALLATION MANUAL

Standard Remote Controller

Simple Remote Controller

ProgramWeeklyTimer

Remote sensor

Remote ControllerWireless Kit

RBC-AMT21E ................................................. 81

RBC-AS21E .................................................... 82

RBC-EXW21E................................................. 83

TCB-TC21LE .................................................. 84

TCB-AX21U (W)-E.......................................... 85

Network Adapter for Air Conditioner

(Use for Indoor Unit Only)

TCB-PCNT20E ............................................... 86

PRECAUTIONS FOR SAFETY

• Ensure that all Local, National and International regulations are satisfied.

• Read this “PRECAUTIONS FOR SAFETY” carefully before Installation.

• The precautions described below include the important items regarding safety. Observe them without fail.

• After the installation work, perform a trial operation to check for any problem.

Follow the Owner’s Manual to explain how to use and maintain the unit to the customer.

• Turn off the main power supply switch (or breaker) before the unit maintenance.

• Ask the customer to keep the Installation Manual together with the Owner’s Manual.

CAUTION

New Refrigerant Air Conditioner Installation

• THIS AIR CONDITIONER ADOPTS THE NEW HFC REFRIGERANT (R410A) WHICH DOES NOT DE-

STROY OZONE LAYER.

The characteristics of R410A refrigerant are ; easy to absorb water, oxidizing membrane or oil, and its pressure

is approx. 1.6 times higher than that of refrigerant R22. Accompanied with the new refrigerant, refrigerating oil

has also been changed. Therefore, during installation work, be sure that water, dust, former refrigerant, or

refrigerating oil does not enter the refrigerating cycle.

To prevent charging an incorrect refrigerant and refrigerating oil, the sizes of connecting sections of charging

port of the main unit and installation tools are charged from those for the conventional refrigerant.

Accordingly the exclusive tools are required for the new refrigerant (R410A).

For connecting pipes, use new and clean piping designed for R410A, and please care so that water or dust

does not enter. Moreover, do not use the existing piping because there are problems with pressure-resistance

force and impurity in it.

CAUTION

To Disconnect the Appliance from Main Power Supply.

This appliance must be connected to the main power supply by means of a switch with a contact separation of

at least 3 mm.

The installation fuse (25A D type

) must be used for the power supply line of this conditioner.

WARNING

• Ask an authorized dealer or qualified installation professional to install/maintain the air condi-

tioner.

Inappropriate installation may result in water leakage, electric shock or fire.

• Turn off the main power supply switch or breaker before attempting any electrical work.

Make sure all power switches are off. Failure to do so may cause electric shock.

• Connect the connecting cable correctly.

If the connecting cable is connected in a wrong way, electric parts may be damaged.

• When moving the air conditioner for the installation into another place, be very careful not to

enter any gaseous matter other than the specified refrigerant into the refrigeration cycle.

If air or any other gas is mixed in the refrigerant, the gas pressure in the refrigeration cycle becomes abnor-

mally high and it may resultingly causes pipe burst and injuries on persons.

• Do not modify this unit by removing any of the safety guards or by by-passing any of the safety

interlock switches.

• Exposure of unit to water or other moisture before installation may cause short-circuit of

electrical parts.

Do not store it in a wet basement or expose to rain or water.

• After unpacking the unit, examine it carefully if there are possible damage.

• Do not install in a place that might increase the vibration of the unit.

• To avoid personal injury (with sharp edges), be careful when handling parts.

• Perform installation work properly according to the Installation Manual.

Inappropriate installation may result in water leakage, electric shock or fire.

• When the air conditioner is installed in a small room, provide appropriate measures to ensure

that the concentration of refrigerant leakage occur in the room does not exceed the critical

level.

• Install the air conditioner securely in a location where the base can sustain the weight adequately.

• Perform the specified installation work to guard against an earthquake.

If the air conditioner is not installed appropriately, accidents may occur due to the falling unit.

• If refrigerant gas has leaked during the installation work, ventilate the room immediately.

If the leaked refrigerant gas comes in contact with fire, noxious gas may generate.

• After the installation work, confirm that refrigerant gas does not leak.

If refrigerant gas leaks into the room and flows near a fire source, such as a cooking range, noxious gas

might generate.

• Electrical work must be performed by a qualified electrician in accordance with the Installation

Manual. Make sure the air conditioner uses an exclusive power supply.

An insufficient power supply capacity or inappropriate installation may cause fire.

• Use the specified cables for wiring connect the terminals securely fix. To prevent external

forces applied to the terminals from affecting the terminals.

• Be sure to provide grounding.

Do not connect ground wires to gas pipes, water pipes, lightning rods or ground wires for telephone cables.

• Conform to the regulations of the local electric company when wiring the power supply.

Inappropriate grounding may cause electric shock.

• Do not install the air conditioner in a location subject to a risk of exposure to a combustible gas.

If a combustible gas leaks, and stays around the unit, a fire may occur.

Required tools for installation work

R410A (Special requirement)

1) Philips screwdriver

2) Hole core drill (65 mm)

3) Spanner

4) Pipe cutter

5) Knife

17) Gauge manifold

(Charge hose : R410A special requirement)

18) Vacuum pump

(Charge hose : R410A special requirement)

19) Torque wrench

1/4 (17 mm) 16 N•m (1.6 kgf•m)

3/8 (22 mm) 42 N•m (4.2 kgf•m)

1/2 (26 mm) 55 N•m (5.5 kgf•m)

5/8 (15.9 mm) 120 N•m (12.0 kgf•m)

20) Copper pipe gauge adjusting projection margin

11) Electro circuit tester

12) Hexagonal wrench

13) Flare tool

14) Pipe bender

15) Level vial

6) Reamer

16) Metal saw

7) Gas leak detector

8) Tape measure

9) Thermometer

10) Mega-tester

21) Vacuum pump adapter

ACCESSORY AND REFRIGERANT

Accessory and Installation Parts

Refrigerant Piping

• Piping kit used for the conventional refrigerant cannot be

used.

• Use copper pipe with 0.8 mm or more thickness for Ø6.4,

Ø9.5, Ø12.7.

Outdoor unit

Protective bush

Installation manual x 1

(For SM800, SP560, SP800)

Use copper pipe with 1.0 mm or more thickness for Ø15.9.

Drain nipple

• Flare nut and flare works are also different from those of

the conventional refrigerant. Take out the flare nut at-

tached to the main unit of the air conditioner, and use it.

Guard material for

passage part

(For SM800, SP560, SP800)

Waterproof rubber cap

SELECTION OF INSTALLATION

<SP560AT-E>

CAUTION

Length of refrigerant pipe

<SP560AT-E, SP800AT-E only>

connected to

Item

indoor/outdoor unit

When using an air conditioner under low outside

temperature condition (Outside temp.:–5°C or

lower) with COOL mode, prepare a duct or wind

shield so that it is not affected by the wind.

Addition of refrigerant is

20m or shorter

unnecessary at the local site.

Add 20g of refrigerant for every

1m of pipe which exceeds 20m.

21m to 50m

* Caution at addition of refrigerant

Suction hood (Side)

Discharge hood

Suction hood

(Rear side)

When the total length of refrigerant pipe exceeds

20m, add 20g/m of refrigerant and the maximum total

length of pipe is 50m.

Discharge

(Max. amount of additional refrigerant is 600g.)

Discharge guide

Fin

Charge the refrigerant accurately. Overcharge may

cause a serious trouble of compressor.

Fin

Suction

<SP800AT-E>

Length of refrigerant pipe

connected to

Item

indoor/outdoor unit

Before installation

Addition of refrigerant is

unnecessary at the local site.

30m or shorter

Be careful to the following items before installation.

Add 40g of refrigerant for every

1m of pipe which exceeds 30m.

31m to 50m

Length of refrigerant pipe

* Caution at addition of refrigerant

<SM560AT-E>

When the total length of refrigerant pipe exceeds

30m, add 40g/m of refrigerant and the maximum total

length of pipe is 50m.

Length of refrigerant pipe

connected to

Item

indoor/outdoor unit

(Max. amount of additional refrigerant is 800g.)

Addition of refrigerant is

20m or shorter

unnecessary at the local site.

Charge the refrigerant accurately. Overcharge may

cause a serious trouble of compressor.

Add 20g of refrigerant for every

1m of pipe which exceeds 20m.

21m to 30m

* Caution at addition of refrigerant

Air purge

When the total length of refrigerant pipe exceeds

20m, add 20g/m of refrigerant and the maximum total

length of pipe is 30m.

• For air purge, use a vacuum pump.

• Do not use refrigerant charged in the outdoor unit for

air purge. (The refrigerant for air purge is not con-

tained in the outdoor unit.)

(Max. amount of additional refrigerant is 200g.)

Charge the refrigerant accurately. Overcharge may

cause a serious trouble of compressor.

<SM800AT-E>

Electrical cabling

Length of refrigerant pipe

• Be sure to fix the power cables and indoor/outdoor

connecting cables with clamps so that they do not

contact with the cabinet, etc.

connected to

Item

indoor/outdoor unit

Addition of refrigerant is

unnecessary at the local site.

20m or shorter

Add 40g of refrigerant for every

1m of pipe which exceeds 20m.

21m to 50m

* Caution at addition of refrigerant

When the total length of refrigerant pipe exceeds

20m, add 40g/m of refrigerant and the maximum total

length of pipe is 50m.

(Max. amount of additional refrigerant is 1200g.)

Charge the refrigerant accurately. Overcharge may

cause a serious trouble of compressor.

Installation Place

Necessary Space for Installation

Obstacle at rear side

• A place which provides a specified space around the

outdoor unit.

• A place where the operation noise and discharged air

are not given to your neighbors.

1. Single unit installation

• A place that is not exposed to a strong wind.

• A place that does not block a passage.

• When the outdoor unit is installed in an elevated

position, be sure to secure its feet.

• There must be sufficient space for carrying in the

unit.

2. Obstacles at both right and left sides.

• A place where the drain water does not make any

The height of the

obstacle should be

lower than the height

of the outdoor unit.

problem.

CAUTION

150

or more

300

or more

1. Install the outdoor unit at a place where dis-

charge air is not blocked.

3. Serial installation of two or more units

2. When an outdoor unit is installed in a place that

is always exposed to a strong wind like a coast

or on a high story of a building, secure a normal

fan operation by using a duct or a wind shield.

3. When installing the outdoor unit in a place that is

constantly exposed to a strong wind such as the

upper stairs or rooftop of a building, apply the

windproof measures referring to the following

examples.

150

or more

300

or more

300

or more

300

or more

The height of the obstacle should be lower

than the height of the outdoor unit.

1) Install the unit so that its

discharge port faces to the

wall of the building. Keep a

distance 500 mm or more

between the unit and the

wall surface.

150

or more

2) Supposing the wind direction during the

operation season of the air conditioner, install

the unit so that the discharge port is set at

right angle to the wind direction.

Obstacle at front side

Strong

wind

Strong

wind

1. Single unit installation

4. Installation in the following places may result in

some troubles. Do not install the unit in such

places below.

2. Serial installation of two or more units

• A place full of machine oil.

• A place full of sulfuric gas.

• A place where high-frequency radio waves are

likely to be generated as from audio equip-

ment, welders, and medical equipment.

SELECTION OF INSTALLATION

Installation of Outdoor Unit

• Before installation, check strength and horizontality of

the base so that abnormal sound does not generate.

1000

or more

• According to the following base diagram, fix the base

firmly with the anchor bolts.

(Anchor bolt, nut: M10 x 4 pairs)

<SM560AT-E>

600

115

Obstacles at both front and rear sides

Open the upper side and both right and left sides.

The height of obstacle at both front and rear side,

should be lower than the height of the outdoor unit.

Ø28 Drain hole

1. Single unit installation

<SM800AT-E, SP560AT-E, SP800AT-E>

150

600

150

430

Drain hole

Drain nipple mounting hole

Knockout hole

2. Serial installation of two or more units

Set the out margin of the anchor bolt to 15mm or less.

15 or less

300

or more

300

or more

• In case of draining through the drain hose, attach the

following drain nipple and the waterproof rubber cap,

and use the drain hose (Inner diam.: 16mm) sold on

the market. And also seal the screws securely with

silicone material, etc. so that water does not drop

down. Some conditions may cause dewing or drip-

ping of water.

Serial installation at front and rear sides

Open the upper side and both right and left sides.

The height of obstacle at both front and rear sides

should be lower than the height of the outdoor unit.

1000

or more

300

or more

1500

or more

2000

or more

200

or more

Drain nipple

Waterproof rubber cap

<SM560AT-E>

Refrigerant Piping Connection

CAUTION

TAKE NOTICE THESE IMPORTANT

Waterproof rubber cap

4 POINTS BELOW FOR PIPING WORK

1. Keep dust and moisture away from inside the

connecting pipes.

2. Tightly connect the connection between pipes

and the unit.

Base plate

3. Evacuate the air in the connecting pipes using

VACUUM PUMP.

Drain nipple

4. Check gas leak at connected points.

<SM800AT-E, SP560AT-E, SP800AT-E>

Knockout hole

Capacity

rank

Liquid side

Gas side

Outer

Thickness

0.8

Thickness

RAV-

diameter

Open

Waterproof rubber cap

Drain nipple

SM560

SP560

Ø6.4

Ø12.7

0.8

SM800

SP800

Ø9.5

0.8

Ø15.9

1.0

• When there is a possibility of freezing of drain at the

cold district or a snowfall area, be careful for drainage

ability of drain.The drainage ability increases when a

knockout hole on the base plate is opened. (Open the

knockout hole to outside using a screwdriver, etc.)

For Reference

If a heating operation would be continuously performed

for a long time under the condition that the outdoor

temperature is 0°C or lower, draining of defrosted water

may be difficult due to freezing of the bottom plate,

resulting in a trouble of the cabinet or fan.

Optional Installation Parts

(Local Procure)

Parts name

Refrigerant piping

Q’ty

It is recommended to procure an anti-freeze heater

locally for a safety installation of the air conditioner.

Liquid side : Ø6.35 mm or Ø9.52 mm

Each one

For details, contact the dealer.

Gas side : Ø12.7 mm or Ø15.9 mm

Pipe insulating material

(polyethylene foam, 6 mm thick)

Putty, PVC tapes

Each one

SELECTION OF INSTALLATION

How to remove the front panel

Knockout of Pipe Cover

1. Remove screws of the front panel.

2. Pull the front panel downward.

<SM800AT-E, SP560AT-E, SP800AT-E>

Removing the front panel, the electric parts appear at

the front side.

• The metal pipes are attachable to the piping holes.

If the size of the used power pipe does not match

with the hole, adjust the hole size to match with pipe

size.

Rear direction

Pipe cover

• Be sure to fix the power cable and indoor/outdoor

connecting cable with bundling band sold on the

market so that they do not make contact with the

compressor and discharge pipe.

(Temperature of the compressor and discharge pipe

becomes high.)

Side direction

Front direction

Down direction

In order to avoid the force applied to on the connect-

ing section, be sure to fix the cables to the cord

clamps provided on the pipe valve fixing plate and the

electric parts box.

Knockout procedure

• The indoor/outdoor connecting pipes can be con-

nected to 4 directions.

Electric parts box

Front panel

Take off the knockout part of the pipe cover in which

pipes or wires pass through the base plate.

• As shown in the figure, do not remove the pipe cover

from the cabinet so that the knockout hole can be

easily punched.To knock out, it is easily taken off by

hands by punching a position at the lower side of 3

connected parts with screwdriver along the guideline.

Pipe valve

fixing plate

Piping

hole

• After marking the knockout hole, remove the burr and

mount the attached protective bush and guard

material for pass-through part in order to protect

pipes and wires.

Cord clamp

After connecting the pipes, be sure to mount the pipe

cover. The pipe cover is easily mounted by cutting off

the slit at the lower part of the pipe cover.

REFRIGERANT PIPING

• Flaring size : A (Unit : mm)

Pipe Forming/End Positioning

0.4

<SM560AT-E>

Outer diam. of copper pipe

• Forming of pipe

R410A

R22

9.0

Form the pipe along with a marked line of the cabinet.

• End positioning of pipe

6.35

9.52

12.7

15.9

9.1

13.2

16.6

19.7

13.0

16.2

19.4

Match the ends of both pipes at a distance of

85 mm apart from the marked line.

* In case of flaring for R410A with the conventional

flare tool, pull it out approx. 0.5 mm more than that of

R22 to adjust to the specified flare size. The copper

pipe gauge is useful for adjusting projection margin

size.

Marked line

• Projection margin in flaring : B (Unit : mm)

Rigid (Clutch type)

Flaring

1. Cut the pipe with a pipe cutter.

Outer diam.

of copper

pipe

R410A tool used

R410A R22

Conventional tool used

R410A R22

6.35

9.52

12.7

15.9

0 to 0.5 (Same as left) 1.0 to 1.5 0.5 to 1.0

90˚

Obliquity Roughness

Warp

Imperial (Wing nut type)

2. Insert a flare nut into the pipe, and flare the pipe.

Outer diam. of

copper pipe

R410A

R22

As the flaring sizes of R410A differ from those of

refrigerant R22, the flare tools newly manufactured

for R410A are recommended.

However, the conventional tools can be used by

adjusting projection margin of the copper

6.35

9.52

12.7

15.9

1.5 to 2.0

2.0 to 2.5

1.0 to 1.5

1.5 to 2.0

pipe.

REFRIGERANT PIPING

Tightening of Connecting Part

REQUIREMENT

(Unit: N•m)

1. Do not put the spanner on the cap. The valve

may be broken.

Outer diam. of copper pipe

6.35mm (diam.)

Tightening torque

2. If applying excessive torque, the nut may be

broken according to some installation conditions.

14 to 18 (1.4 to 1.8kgf•m)

33 to 42 (3.3 to 4.2kgf•m)

50 to 62 (5.0 to 6.2kgf•m)

68 to 82 (6.8 to 8.2kgf•m)

9.52mm (diam.)

12.7mm (diam.)

• After the installation work, be sure to check gas leak

of connecting part of the pipes with nitrogen.

15.9mm (diam.)

Flare at

indoor unit side

Cover

Flare at

outdoor unit side

• Align the centers of the connecting pipes and tighten

the flare nut strong as far as possible with your

fingers.

Then fix the nut with a spanner and tighten it with

torque wrench as shown in the figure.

Half union or packed valve

Flare nut

• Pressure of R410A is higher than that of R22

(Approx. 1.6 times).Therefore, using a torque

wrench, tighten the flare pipe connecting sections

which connect the indoor/outdoor units at the speci-

fied tightening torque. Incomplete connections may

cause not only a gas leak, but also a trouble of the

refrigeration cycle.

Externally

threaded side

Internally

threaded side

Fix with spanner.

Tighten with torque wrench.

• As shown in the figure, be sure to use a double

spanner to loosen or tighten the flare nut of the valve

at gas side. If using a single spanner, the nut cannot

be tightened with necessary tightening torque.

Do not apply refrigerating machine oil to

the flared surface.

On the contrary, use a single spanner to loosen or

tighten the flare nut of the valve at liquid side.

Cover

Cap

Piping valve

Loosened

Tightened

Flare nut

SM800 type valve at gas side

EVACUATING

Air Purge

This air conditioner can be installed up to the connecting pipe length and height difference in the following table.

Height difference (m)

Max. connecting

pipe length (m)

Hexagonal

wrench size

Capacity rank

Outdoor unit at upper side Outdoor unit at lower side

SM560 type

4mm

SM800, SP560, SP800 type

With respect to the preservation of terrestrial environment, adopt “Vacuum pump” for air purge (Evacuate air in

the connecting pipes) when installing the unit.

• Do not discharge the refrigerant gas to the atmosphere to preserve the terrestrial environment.

• Use a vacuum pump to discharge the air (nitrogen, etc.) remained in the set. If the air remains, the capacity

may decrease.

For the vacuum pump, be sure to use one with backflow preventer so that the oil in the pump does not backflow

into the pipe of the air conditioner when the pump stops. (If oil in the vacuum pump is put in an air conditioner

including R410A, it may cause trouble on the refrigeration cycle.)

Vacuum pump

As shown in the right figure, connect the charge hose after the manifold valve are closed completely.

Attach the connecting port of the charge hose with a projection to push the valve core (setting pin) to the charge port of the set.

Open the handle Low fully.

Turn ON the vacuum pump (*1)

Loosen the flare nut of the packed valve (Gas side) a little to check the air passes through. (*2)

Tighten the flare nut again.

Execute vacuuming until the compound pressure gauge indicates –101kPa (–76cmHg). (*1)

Close handle Low completely.

Turn OFF the vacuum pump.

Leave the vacuum pump as it is for 1 or 2 minutes, and check the indicator of the compound pressure gauge does not return.

Open fully the valve stem or the valve handle. (First, at liquid side, then gas side)

Disconnect the charge hose from the charge port.

Tighten valve and caps of the charge port surely.

EVACUATING

<SM560AT-E>

How to open the valve

Compound pressure gauge

Pressure gauge

Valve unit

–101kPa

(–76cmHg)

Manifold valve

Handle Lo

Handle Hi

(Keep fully closed)

Handle

Pull out the handle and

using cutting pliers, etc.

turn it counterclockwise

by 90˚. (Open fully)

Charge hose

(For R410A only)

Charge hose

(For R410A only)

Vacuum pump adapter

for counter-flow prevention

(For R410A only)

Charge port

Flare nut

Valve unit

Vacuum

pump

Packed valve (Gas side)

Service port (Valve core (Setting pin))

Push in handle.

Flare nut

Valve unit

Stopper

Charge cap

Charge port

Flare nut

Charge port

Valve rod

Handle position

<SM800AT-E, SP560AT-E, SP800AT-E>

Compound pressure gauge

Pressure gauge

–101kPa

(–76cmHg)

Handle

Manifold valve

Handle Lo

Handle Hi

Closed completely

Opened fully

(Keep fully closed)

Charge hose

(For R410A only)

*1. Use the vacuum pump, vacuum pump adapters,

and gauge manifold referring to the manuals

attached to each tool before using them. For the

vacuum pump, check oil is filled up to the specified

line of the oil gauge.

Charge hose

(For R410A only)

Service port

(Valve core (Setting pin))

Vacuum pump adapter

for counter-flow prevention

(For R410A only)

*2. While the air is purged, check again that the

connecting port of charge hose, which has a

projection to push the valve core, is firmly con-

nected to the charge port.

Vacuum

pump

Packed valve at gas side

Valve handling precautions

• Open the valve stem or the handle until it strikes

the stopper. It is unnecessary to apply further

force.

Ø6.4

14 to 18N•m (1.4 to 1.8kgf•m)

Ø9.5

33 to 42N•m (3.3 to 4.2kgf•m)

Valve size

Ø12.7 33 to 42N•m (3.3 to 4.2kgf•m)

Ø15.9 20 to 25N•m (2.0 to 2.5kgf•m)

14 to 18N•m (1.4 to 1.8kgf•m)

• Securely tighten the cap with a torque wrench.

• Cap tightening torque

Charge port

ELECTRICAL WORK

For the air conditioner that has no power cable, connect

a power cable as mentioned below.

How to wire

1. Connect the connecting cable to the terminal as

identified with their respective numbers on the

terminal block of indoor and outdoor unit.

SM800AT-E

Model RAV-

SM560AT-E SP560AT-E

H07 RN-F or 245 IEC 66 (1.0 mm²or more)

SP800AT-E

2. When connecting the connecting cable to the

outdoor unit terminal, prevent water coming in the

outdoor unit.

220 – 240 V

Single phase 50 Hz

Power supply

Maximum running current

Installation fuse rating

12A

15A

3. Insulate the unsheathed cords (conductors) with

electrical insulation tape. Process them so that they

do not touch any electrical or metal parts.

25 A (D type

)

H07 RN-F or 245 IEC 66

(2.5 mm²or more)

Power cable

4. For inter connecting cable, do not use a wire jointed

to another on the way.

Use wires long enough to cover the entire length.

CAUTION

Terminal block

• Wrong wiring may cause a burnout to some

electrical parts.

• Be sure to use the cord clamps attached to the

product.

• Do not damage or scratch the conductive core

and inner insulator of power and inter-connecting

cables when peeling them.

Screw

Power cable

Connecting

cable

• Be sure to comply with local regulations of the

cable from outdoor unit to indoor unit.

(wire size and cabling method etc.)

• Use the power and Inter-connecting cables with

specified thickness, specified type and protective

devices required.

Stripping length power cord and connecting cable

1 2 3

<SM560AT-E>

How to remove the valve cover

1. Remove screws of the valve cover.

2. Pull the valve cover downward to remove it.

Earth line Earth line

(mm)

Connecting

cable

Power cable

Valve cover

CAUTION

Piping cover

• The installation fuse (25A D type

) must

be used for the power supply line of this air

conditioner.

Cord clamp

• Incorrect/incomplete wiring might cause an

electrical fire or smoke.

Indoor/outdoor

connecting cables

• Prepare the exclusive power supply for the air

conditioner.

Power cable

• This product can be connected to the mains.

Connection to the fixed wiring :

A switch which disconnects all poles and has a

contact separation of at least 3 mm must be

incorporated in the fixed wiring.

FINAL INSTALLATION CHECKS

Check and Test Operation

Valve cover

For R410A, use the leak detector exclusively manufactured for

HFC refrigerant (R410A, R134a, etc.).

Piping

cover

The conventional leak detector for HCFC refrigerant (R22,

etc.) cannot be used because its sensitivity for HFC refrigerant

lowers to approx. 1/40.

Flare nut

connections

(Indoor unit)

• Pressure of R410A is approx. 1.6 times higher than that of

R22.

If installation work is incompletely finished, a gas leakage may

occur when pressure rises during operation.

Therefore, be sure to test the piping connections for leakage.

Check points

of outdoor unit

• Check gas leakage at the flare nut connections, valve stem

cap connections and service port cap fittings with a leak

detector or soap water.

CAUTION

When the remote controller is used for the first time, it accepts an operation approx. 5 minutes after the power

supply has been turned on.

It is not a trouble, but is because the setup of the remote controller is being checked.

For the second power-ON time and after, approx. 1 minute is required to start the operation by the remote controller.

Useful Functions

(SM800AT-E, SP560AT-E, SP800AT-E)

Self-Diagnosis by LED Indication

In addition to the code checking by remote controller of the indoor unit, troubles of the outdoor unit can be diag-

nosed by LED indications on the cycle control P.C. board of the outdoor unit. Utilize them for various checks.

For the check by remote controller of the indoor unit, refer to the Installation Manual of the indoor unit.

Before a check, confirm each bit of the DIP switch is set to OFF position.

LED indication and code checking

Cycle control P.C. board

LED indication

Cause

D800 D801 D802 D803

Heat exchanger sensor (TE) error

Suction sensor (TS) error

Discharge sensor (TD) error

High-pressure protection error

Outdoor temperature sensor (TO) error

DC outside fan error

D800 ¡ : Red

D801 ¡ :Yellow

D802 ¡ :Yellow

D803 ¡ :Yellow

Communication error between IPDU (Abnormal stop)

High-pressure release operation

Discharge temp. error

¥ : Rapid flash

l : Go off

EEPROM error

Communication error between IPDU (No abnormal stop)

G-Tr short-circuit protection

Detect circuit error

¡ : Go on

Current sensor error

Comp. lock error

Comp. break down

Installation/ServicingTools

Changes in the product and components

In the case of an air conditioner using R410A, in order to prevent any other refrigerant from being charged acciden-

tally, service port diameter of the outdoor unit control valve (3 way valve) has been changed. (1/2 UNF 20 threads

per inch)

• In order to increase the pressure resisting strength of the refrigerant piping flare processing diameter and size of

opposite side of flare nuts has been changed. (for copper pipes with nominal dimensions 1/2 and 5/8)

New tools for R410A

Applicable to R22 model

Changes

As pressure is high, it is impossible to measure by means of conventional

gauge. In order to prevent any other refrigerant from being charged, each

port diameter is changed.

Gauge manifold

In order to increase pressure resisting strength, hose materials and port

size are changed (to 1/2 UNF 20 threads per inch).

When purchasing a charge hose, be sure to check the port size.

Charge hose

Electronic balance

for refrigerant charging

As pressure is high and gasification speed is fast, it is difficult to read the

indicated value by means of charging cylinder, as air bubbles occur.

Torque wrench

The sizes of opposite sides of flare nuts have been increased. Inciden-

tally, a common wrench is used for nominal diameters 1/4 and 3/8.

(nominal diam. 1/2, 5/8)

Flare tool

(clutch type)

By increasing the clamp bar’s receiving hole, strength of spring in the tool

has been improved.

Gauge for projection adjustment

—

Used when flare is made with using conventional flare tool.

Connected to the conventional vacuum pump. It is necessary to use an

adapter to prevent vacuum pump oil from flowing back to the charge hose.

The charge hose connecting part has two ports - one for conventional

refrigerant (7/16 UNF 20 threads per inch) and the other for R410A. If the

vacuum pump oil (mineral) mixes with R410A, sludge may occur and

damage the equipment.

Vacuum pump adapter

Gas leakage detector

Exclusive for HFC refrigerant.

• Incidentally, the “refrigerant cylinder” comes with the refrigerant designation (R410A) and protector coating in the

U.S.’s ARI specified rose color (ARI color code: PMS 507).

• Also, the “charge port and packing for refrigerant cylinder” require 1/2 UNF 20 threads per inch corresponding to

the charge hose’s port size.

PRECAUTIONS FOR SAFETY

• Ensure that all Local, National and International regulations are satisfied.

• Read this “PRECAUTIONS FOR SAFETY” carefully before Installation.

• The precautions described below include the important items regarding safety. Observe them without fail.

• After the installation work, perform a trial operation to check for any problem.

Follow the Owner’s Manual to explain how to use and maintain the unit to the customer.

• Turn off the main power supply switch (or breaker) before the unit maintenance.

• Ask the customer to keep the Installation Manual together with the Owner’s Manual.

CAUTION

New Refrigerant Air Conditioner Installation

• THIS AIR CONDITIONER ADOPTS THE NEW HFC REFRIGERANT (R410A) WHICH DOES NOT DE-

STROY OZONE LAYER.

The characteristics of R410A refrigerant are ; easy to absorb water, oxidizing membrane or oil, and its pressure

is approx. 1.6 times higher than that of refrigerant R22. Accompanied with the new refrigerant, refrigerating oil

has also been changed. Therefore, during installation work, be sure that water, dust, former refrigerant, or

refrigerating oil does not enter the refrigerating cycle.

To prevent charging an incorrect refrigerant and refrigerating oil, the sizes of connecting sections of charging

port of the main unit and installation tools are charged from those for the conventional refrigerant.

Accordingly the exclusive tools are required for the new refrigerant (R410A).

For connecting pipes, use new and clean piping designed for R410A, and please care so that water or dust

does not enter. Moreover, do not use the existing piping because there are problems with pressure-resistance

force and impurity in it.

CAUTION

To Disconnect the Appliance from Main Power Supply.

This appliance must be connected to the main power supply by means of a switch with a contact separation of

at least 3 mm.

The installation fuse (25A D type

) must be used for the power supply line of this conditioner.

WARNING

• Ask an authorized dealer or qualified installation professional to install/maintain the air condi-

tioner.

Inappropriate installation may result in water leakage, electric shock or fire.

• Turn off the main power supply switch or breaker before attempting any electrical work.

Make sure all power switches are off. Failure to do so may cause electric shock.

• Connect the connecting cable correctly.

If the connecting cable is connected in a wrong way, electric parts may be damaged.

• When moving the air conditioner for the installation into another place, be very careful not to

enter any gaseous matter other than the specified refrigerant into the refrigeration cycle.

If air or any other gas is mixed in the refrigerant, the gas pressure in the refrigeration cycle becomes abnor-

mally high and it may resultingly causes pipe burst and injuries on persons.

• Do not modify this unit by removing any of the safety guards or by by-passing any of the safety

interlock switches.

• Exposure of unit to water or other moisture before installation may cause a short-circuit of