9,000 BTU Portable Air Conditioner
PE1-09R-30
Operating Instructions
Model No. PE1-09R-30
®
© 2006 Soleus Air International
PACKAGE CONTENTS
Portable Air Conditioner
Exhaust Hoses (2)
Hose Adapters (2)
W indow Kit Adapter (2)
Remote Control
AAA Batteries (2)
W indow Kit - 3 Sliding Panels (1 dual hose panel, 2 extension panels)
Air Intake and Outlet Covers (2)
Owner‘s Manual
W ARNING: This unit has a voltage rating of 115
volts. The cord has a plug as shown in A. An adapter as
shown in C is available for connecting three-blade
grounding-type plugs to two-slot receptacles. The
grounding lug extending from the adapter must be con-
nected to a permanent ground such as a properly
grounded outlet box. The adapter should not be used if
a three-slot grounded receptacle is available.
DO NOT DEFEAT THE SAFETY PURPOSE OF
THE GROUNDED PLUG.
SPECIFICATIONS
MODEL
PE1-09R-30
9,000 BTU/H
1200 W atts
50 pts/Day
980 W
ñ
The cooling capacity is meas-
ured at an ambient temperature
of DB 86 °F, W B 78 °F.
COOLING CAPACITY
HEATING CAPACITY
DEHUMIDIFYING CAPACITY
ñ
Noise level is measured at a
distance of 3.28 ft away from
the front of the unit, when the
unit is in cooling mode.
COOLING
HEATING
AIR FLOW VOLUME
POW ER
1350W
177 CFM
ñ
ñ
Power consumption is meas-
ured when the fan runs at the
highest speed setting.
115 V~ 60 HZ
9/12 AMP
HEATING/COOLING
POW ER SOURCE
SOUND PRESSURE LEVEL
NET W EIGHT
46 dB(A)
75 Lbs
These specifications are for
reference only. For actual data,
please refer to the rating label
on the back of the unit.
COOLING
60.8̧-108̧ꢀ
23̧-89.6̧ꢀ
OPERATING
TEMPERATURE
HEATING
ñ
If the environment temperature
is higher than the max operat-
ing temperature or lower than
the minimum operating tem-
perature, the air conditioner
may not work properly.
ASSEMBLED
PACKAGE
17.75“ W x 18.25“ D x 32.5“ H
DIMENSIONS
21“ W x 18.5“ D x 34.5“ H
R22
REFRIGERANT
3
PRODUCT DIAGRAM
Control Panel
Louvers
Signal Receptor
Casters
Filter Compartment
4
PARTS & ASSEMBLY
PARTS
EXHAUST HOSE
W INDOW KIT
ASSEMBLY & INSTALLATION
INSTALLATION
W hen the unit is operating as an air conditioner or dehumidifier, the unit draws in fresh outdoor air and exhausts hot air
out of the room to complete the air exchange. W hen the unit is operating in fan or heater modes, no outdoor air exchange
takes place. The window kit and exhaust hose do not need to be installed when the unit is used as a fan or heater.
NOTE: The supplied window kit can be installed in sliding windows and sliding glass doors up to 8 ft. long
(approximate length).
MOUNTING THE EXHAUST HOSES
ñ
Choose a suitable location, near a grounded electrical outlet and suitable window or door. Remove
packaging and locate components.
ñ
ñ
Extend both ends of the exhaust hoses approximately 6 inches.
Screw the window kit adapter onto one end of the exhaust hose clockwise. Screw the hose adapter onto
the other end of the exhaust hose clockwise. Repeat on the other exhaust hose.
ñ
ñ
Remove outlet covers from the back of the unit by screwing them counter-clockwise, then lifting up.
Mount the exhaust hoses onto the back of the unit by locking the hose adapters into place.
5
DUAL HOSE W INDOW KIT INSTALLATION
6
CONTROL PANEL, DISPLAY, & OPERATING INSTRUCTIONS
CONTROL PANEL & MULTI-COLOR DISPLAY
CONTROL PANEL
TEMP & TIMER SELECTION
POW ER BUTTON
MODE BUTTON
TIMER BUTTONS
SW ING (LOUVER
OSCILLATION)
FAN SPEED BUTTON
MULTI-COLOR DISPLAY
AUTO
A/C
DEHUM.
FAN
HEAT
TIMER ON
TIMER OFF
FAN SPEED
TEMPERATURE
AND TIMER
INDICATOR
OSCILLATION ON/OFF
EMERGENCY
CONDENSATE-
BUCKET FULL
SLEEP MODE ON/OFF
7
OPERATING INSTRUCTIONS
CONTROL PANEL BUTTONS (Refer to the images on page 7)
1) Power On and Off - Press the POW ER button once to manually turn the unit on. Press the POW ER
button once more to turn the unit off.
2) Mode Selection - Press the M ODE Button repeatedly to cycle between the different modes: Auto mode,
Air Conditioner, Dehumidifier, Fan only, and Heater.
3) Fan Speed Control - Press the FAN SPEED Button to cycle through the different fan speeds: High,
M edium, and low. The fan speed can be visually distinguished by the speed of the digital air segments
progressing out from the windmill fan image on the Multi-color display. There is an additional auto speed
setting that is enabled in only heating and cooling modes. This speed is next setting after low when press-
ing the speed control button. The speeds will cycle through in this order: Low, M edium, High, Auto. Each
change in speed will be associated with a —beep“ sound from the unit.
4) Temperature - Select the desired temperature by pressing either 9 or : key when using the unit in
cooling or heating mode. The temperature indicator flashes to display the desired temperature setting. After
the temperature is set, the unit will display this temperature setting until it is changed by the user. The
Multi-color display shows temperature in Celsius or Fahrenheit. Press the °F/°C button on the control
panel to select the desired temperature setting.
5) SW ING - To turn on the exclusive W AVEFLO® oscillation, press the SW ING button on the control
panel. Once you press SW ING, the louvers on the unit will oscillate up and down and back and forth.
6) Timer - To program the timer, press the TIM ER ON button until the display shows a flashing —
“.
Press the : or 9 buttons to change the clock to the desired time for the unit to automatically turn on.
Press the TIM ER OFF button and the display on the unit will flash —
“. Press the : or 9
buttons to change the clock to the desired time for the unit to automatically turn off. The TIM ER OFF
indicator will flash for 3 seconds to activate the times you programmed.
NOTE: The timer will also remember your settings when it is set. If you set the timer while in Air Condition-
ing mode, the timer will automatically turn the unit on and off in air conditioning mode according to the de-
sired programmed times. The timer will also remember the temperature settings, fan speed, and oscillation set-
ting. The timer works when the unit is in Air Conditioner mode, Heating mode, Dehumidifier mode, Fan
mode, and Auto mode
OPERATING THE UNIT USING THE CONTROL PANEL
Air Conditioner Mode
1) Install the exhaust hoses and window kit properly (see pages 6 & 7).
2) Plug the Power Cord into an electrical outlet.
3) Turn on the unit by pressing the POW ER button on the control panel.
4) Press the Mode button until the —
“ icon appears on the Multi-color display
5) Press the : or 9 buttons until the desired room temperature appears on the control panel
display. The temperature ranges from 61°F - 88 °F (16 °C - 31 °C).
8
6) Select the desired fan speed by pressing the FAN button.
NOTE: During hot days, the unit will cool the room most efficiently by setting the temperature at the lowest
setting and the fan speed on high. Reducing the length of the exhaust duct, insulating the exhaust hose and
window kit, and keeping direct sunlight to a minimum will also improve the cooling efficiency.
Dehumidifier Mode
1) Install the exhaust hoses and window kit properly (see pages 6 & 7).
2) Plug the Power Cord into an electrical outlet.
3) Turn on the unit by pressing the POW ER Button on the control panel.
4) Press the M ODE button until the —
“ appears on the control panel display.
NOTE: The unit operates at low fan speed during dehumidifier mode. The unit cools room slightly during
the dehumidification. Keep the windows and doors closed to aid the effectiveness of the unit in removing the
moisture from the room.
NOTE: The unit will not perform in dehumidifier mode when the room temperature is lower than 61°F .
Fan Mode
1) Plug the Power Cord into an electrical outlet.
2) Turn on the unit by pressing the POW ER button on the control panel.
3) Press the M ODE button until the —
“ icon appears on the control panel display.
4) Select the fan speed by pressing the FAN button.
5) To circulate more air, press the SW ING button on the remote control. The louvers will oscillate in our
exclusive W AVEFLO® pattern; back and forth and up and down, spreading more air throughout the
room.
NOTE: It is not necessary for the exhaust hoses and window kit to be installed to operate the unit in fan mode.
Heating Mode
1) Plug the Power Cord into an electrical outlet.
2) Turn on the unit by pressing the POW ER button on the control panel.
3) Press the M ODE button until the —
— icon appears on the control panel display.
4) Press the 9or : buttons until the desired room temperature appears on the control panel display. The
temperature ranges from 61°F - 88 °F (16 °C - 31 °C).
5) Select the fan speed by pressing the FAN button. It is recommended to set the fan speed to low.
Auto Mode
1) Install the exhaust hoses and window kit properly (see pages 6 & 7).
2) Plug the Power Cord into an electrical outlet.
3) Turn on the unit by pressing the POW ER button on the control panel.
4) Press the M ODE button until the —
“ icon appears on the control panel display. Select the fan speed
by pressing the FAN button.
9
NOTE: During AUTO mode, the unit operates in Heating mode when the room temperature is below 68 °F,
Dehumidifier mode when the room temperature is between 68 °F to 80 °F. And Air Conditioner mode when
the room temperature is above 80 °F.
Emergency Condensate Holding Tank
W hen the room temperature is low and the indoor humidity is high, the air conditioner may not be able to
evaporate some of the moisture fast enough. W hen this happens, the water will accumulate in an emergency
condensate tank inside the unit. Once the emergency condensate tank is full, the unit will automatically shut
off and the —
“ will appear on the control panel display. To empty the condensate tank, pull the drain plug
at the bottom back of the unit. You will need a small pan, approximately 1“ high to catch the water coming out
of the condensate tank. Once the condensate tank is drained, the unit will begin working within a few minutes.
The emergency condensate tank is approximately 1.5 Liters of water. Another option is to purchase a small
hose from a hardware store that can fit around the 5/8“ drain plug on the back of the unit and drain the unit into
a gravity drain or larger pan for continuous drainage. It is not advised to use continuous drainage when the
room temperature is higher than 90°F .
10
OPERATING THE UNIT USING THE REMOTE CONTROL
REMOTE CONTROL
LCD DISPLAY
MODE BUTTON
FAN SPEED
POW ER BUTTON
TEMP SETTING
TIMER ON
SW ING (LOUVER
OSCILLATION)
SLEEP BUTTON
TIMER OFF
MINUTE SELECTER
HOUR SELECTER
11
REMOTE CONTROL OPERATING INSTRUCTIONS
1) Power On and Off - Press the POW ER (I/O) button once to manually turn the unit on. Press the Power
button once more to turn the unit off. W hen you press the POW ER button the upper right square on the
remote control LCD Display will light up. W hen in Air Conditioner, Heating, and Auto mode, the selected
temperature will appear on the remote control display. W hen the unit is in Fan mode and Dehumidifier
mode you will see the —- -“ icon instead of the set temperature. This shows that temperature selection is not
available when the unit is in Fan or Dehumidifier mode.
2) Mode Selection - Press the M ODE Button repeatedly to cycle between the different modes: Auto, Air
Conditioner, Dehumidifier, Fan only, and Heater mode. The upper left square on the Remote control dis-
play will light up showing which mode is selected. In Air Conditioner mode the display will show
—COOLING“, in Heating mode the display will show —HEAT“, in Dehumidifier mode the display will
show —DRY“, in Fan mode the display will show —FAN“, and in Auto mode the display will show
—AUTO“.
3) Fan Speed - Press the FAN speed button to cycle through low, medium, and high fan speeds. The dis-
play on the remote control will show LOW , MED, & HIGH under the —SPEED“ label on the remote con-
trol LCD display. There is an additional auto speed setting that is enabled in only heating and cooling
modes. This speed is next setting after low when pressing the FAN speed button on the remote control.
The speeds will cycle through in this order: High, M edium, Low, Auto. Each change in speed will be as-
sociated with a —beep“ sound from the unit. The remote control will not display —AUTO“ under the speed
label. Once Auto fan speed is selected the unit will beep and there will not be a fan speed displayed on the
remote control.
4) Temperature Setting - W hen the unit is in Air Conditioner or Heating mode you can select your desired
temperature. Press the K or L to select your desired temperature setting. The temperature on the LCD dis-
play on the remote control will increase or decrease accordingly. Pressing the L and K buttons simultane-
ously will change the temperature select between °F and °C.
5) SW ING - To turn on the exclusive W AVEFLO® oscillation, press the SW ING button on the remote
control. Once you press SW ING, the louvers on the unit will oscillate up and down and back and forth.
The bottom left square of the remote control display will show the —
oscillation (SW ING) is selected.
— icon when W AVEFLO®
6) TIMER - To program the timer, first press the T-ON button. Once T-ON is pressed the auto-on timer will
blink in the bottom right rectangle of the remote control display. Press the MIN and HOUR buttons to
change the clock to the desired time for the unit to automatically turn on. The minutes will increase by 10
with each press of the M IN button and the hours will increase by 1 with each press of the HOUR button.
Press the T-OFF button and the remote control display will flash the desired auto-off timer. Press the MIN
and HOUR buttons to change the clock to the desired time for the unit to automatically turn off. The timer
is set when the auto-off time stops flashing and the words —ON“ and —OFF“ are displayed next to the time.
7) CLOCK - To set the clock on the remote control, hold down either the M IN or HOUR button until the
displayed time flashes on the remote control display. Change the minutes by pressing the M IN button and
change the hours by pressing the HOUR button.
12
MAINTENANCE
Note: Make sure power is off and the power cord is not plugged into an electrical outlet prior to
performing any maintenance on the unit.
Clean or replace filter - If the air filter is blocked with a dust, the airflow volume may reduce. It is
recommended to clean the filter once every two weeks or as needed.
1) Remove the filter from the filter compartment on the back of the unit.
2) W ash the air filter by immersing it gently into warm water with a neutral detergent. Rinse the filter
and dry it thoroughly out of sunlight.
3) Slide the filter back into the filter compartment after it is thoroughly dried.
4) If the filter is torn or unusable, order a new filter by calling the customer service number on the
warranty page of this manual.
Clean the unit Housing
1) Keep the unit from being exposed directly to the sun to prevent color fading.
2) Clean the surface with a damp cloth and dry it with a soft towel.
Storing the Unit for an Extended Period of Time or Transporting the unit
1) Empty any excess water by unplugging the water drainage stop in the back of the unit (located at
the bottom).
2) Unplug the unit.
3) The unit should be stored in a cool dry place.
DISCLAIMER
ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER‘S MANUAL ARE THE
PRESENTATION OF THE MANUFACTURER. SOLEUS INTERNATIONAL HAS NOT CONDUCTED INDEPENDENT
TEST TO THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREW ITHIN.
13
WARRANTY
One Year Limited W arranty
Soleus International Inc. warrants the accompanying Soleus Air PE1-09R-30 Portable Air Conditioner to be free of de-
fects in material and workmanship for the applications specified in its operation instruction for a period of ONE (1) year
from the date of original retail purchase in the United States.
If the unit exhibits a defect in normal use, Soleus International Inc. will, at its option, either repair or replace it, free of
charge within a reasonable time after the unit is returned during the warranty period.
As a condition to any warranty service obligation, the consumer must present this W arranty Certificate along with a
copy of the original purchase invoice.
THIS W ARRANTY DOES NOT COVER:
ñ
Damage, accidental or otherwise, to the unit while in the possession of a consumer not caused by a defect in
material or workmanship.
ñ
Damage caused by consumer misuse, tampering, or failure to follow the care and special handling provisions
in the instructions.
ñ
ñ
Damage to the finish of the case, or other appearance parts caused by wear.
Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus Interna-
tional Inc.
ñ
Freight and Insurance cost for the warranty service.
ALL W ARRANTIES, INCLUDING ANY IMPLIED W ARRANTY OF MERCHANT ABILITY ARE LIMITED TO
ONE-YEAR DURATION OF THIS EXPRESS LIMITED W ARRANTY. SOLEUS INTERNATIONAL INC.
DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT
SHALL SOLEUS INTERNATIONAL INC‘S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR
BREACH OF ANY W RITTEN OR IMPLIED W ARRANTY W ITH RESPECT TO THIS UNIT.
This warranty covers only new products purchased from our authorized dealers or retailers. It does not cover used, sal-
vaged, or refurbished products.
As some states do not allow the limitation or exclusion of incidental or consequential damages, or do not allow
limitation on implied warranties, the above limitations and exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that vary from state to state.
For W arranty, Technical Support, Customer Service, M issing or Defective Parts
Please Call (888) 876-5387
Or W rite To:
Soleus International Inc.
9451 Telstar Ave.
El Monte, CA 91731 USA
14
|