OWNER’S MANUAL
Model SC-7500A
For 6 and 12-Volt Batteries
™
SpeedCharge
computer
smart
™
a m p
a m p
E N G I N E
S T A R T
S
L
O
W
75
2
C H A R G E
a m p
F
A
S
T
12 30
C H A R G E
Fully Automatic
Microprocessor Controlled
Battery Charger with
Engine Starter
CAUTION:
Read all Safety Rules and Operating Instructions,
and follow them with each use of this product.
Schumacher Electric Corporation
Mount Prospect, IL 60056 U.S.A.
Send Warranty Product Repairs to:
Customer Service Returns
P.O. Box 280,1025 E. Thompson, Hoopeston, IL 60942-0280
Questions? Call Customer Service: 1-800-621-5485
0099000621/0206
IMPORTANT SAFETY INSTRUCTIONS
WARNING – RISK OF EXPLOSIVE GASES
WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BAT-
TERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY
OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT
EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL
AND FOLLOW THE INSTRUCTIONS EXACTLY.
To reduce risk of battery explosion, follow these instructions and those published by
battery manufacturer and manufacturer of any equipment you intend to use in vicinity of
battery. Review cautionary markings on these products and on engine.
SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions for battery charger
model SC-7500A.
• WARNING: Handling the cord on this
product or cords associated with ac-
cessories sold with this product, may
expose you to lead, a chemical known
to the State of California to cause
cancer and birth defects or other
reproductive harm. Wash hands after
handling.
• To reduce risk of electrical shock,
unplug the charger from the outlet
before attempting any maintenance or
cleaning.
• Always charge battery in a well-venti-
lated area.
• WARNING: Battery chargers get hot
during operation and must have proper
ventilation. Air needs to flow around
entire charger. Do not set charger on
flammable materials like carpeting,
upholstery, paper, cardboard, etc.
Charger may damage leather and melt
plastic and rubber.
• Read all instructions and cautions
printed on the battery charger, battery,
and vehicle or equipment using bat-
tery.
• Use charger only on lead-acid type
rechargeable batteries, such as those
used in cars, trucks, tractors, air-
planes, vans, RVs, trolling motors, etc.
This charger is not intended to supply
power to a low voltage electrical
system other than in a starter-motor
application.
HELP US HELP YOU ——
Remember:
Place charger as far away from the bat-
tery being charged as the charger cables
will permit.
• Never use charger for charging dry
cell batteries that are commonly used
with home appliances like radios, ste-
reos, remote controls, etc. These bat-
teries may burst and cause personal
injury.
Do not expose charger to rain or snow.
Never charge a frozen battery. If battery
fluid (electrolyte) becomes frozen, bring
battery into a warm area to thaw before
you begin charging.
Never allow battery acid to drip on char-
ger when reading specific gravity or filling
battery.
• Do not disassemble charger. Take it
to a qualified service professional if
service or repair is required. Incorrect
assembly may result in fire or electri-
cal shock.
Never set a battery on top of the charger.
3
Neverplacechargerdirectlyabovebattery
being charged. The gases from the battery
will corrode and damage the charger.
topreventitfrombeingsteppedon, tripped
over, or damaged.
Never pull out the plug by the cord when
unplugging the charger. Pulling on the
cord may cause damage to the cord or
the plug.
Never touch the battery clamps together
when the charger is on. You could cause
a spark.
Never operate charger if it has received
a hard blow, been dropped, or otherwise
damaged.Takeittoaqualifiedprofessional
for inspection and repair.
Do not operate the charger if it has a
damaged power cord or plug. Have the
cord replaced.
Besuretopositionthechargerpowercord
PERSONAL SAFETY PRECAUTIONS
• Wear complete eye and clothing
protection when working with lead-
acid batteries.
• Remove all personal metal items
from your body such as rings, brace-
lets, necklaces and watches, while
working with a lead-acid battery. A bat-
tery can produce a short circuit current
high enough to weld a ring (or the like)
to metal, causing a severe burn.
• Make sure that someone is within
range of your voice to come to your
aid if needed while you work with or
are near a lead-acid battery.
• Take care not to drop any metal tool
or metal object onto the battery. This
may spark or short circuit the battery
or another electrical device that may
cause an explosion.
• Have plenty of fresh water and soap
nearby for use in case battery acid
contacts your eyes, skin, or clothing. If
this happens, wash immediately with
soap and water. Then get medical at-
tention.
• Always operate the battery charger in
an open, well-ventilated area.
• Avoid touching your eyes while
working with a battery. Acid particles
(corrosion) may get into your eyes. If
this occurs, flush eyes immediately
with running cold water for at least 10
minutes. Then immediately get medi-
cal attention.
• Never smoke or allow a spark or flame
in the vicinity of the battery or engine.
Batteries generate explosive gases.
• Neutralize any acid spills thoroughly
with baking soda before attempting to
clean up.
4
BEFORE USING YOUR BATTERY CHARGER
It is important to understand your charger's requirements. This section will tell you about
your charger's electrical requirements and how to prepare a battery for charging.
PLUGGING IT IN
Wrap clamp cables after unplugging the
power cord from the AC wall outlet and
store your charger in a dry location.
Your charger requires a 120V AC 2-prong
wall outlet receptacle installed according
to all local codes and ordinances.
USING AN EXTENSION CORD
The use of an extension cord is not rec-
ommended. If you must use an extension
cord, please make sure that you follow
these guidelines:
• Make sure that the pins on charger's
power cord fit firmly into the extension
cord, and that the extension cord fits
firmly into the receptacle.
• Checkthattheextensioncordisproperly
wired and in good electrical condition.
• Make sure that the wire size is large
enough for its length and for the AC
ampere rating, as specified in the chart
below.
ASSEMBLING YOUR CHARGER
Included with your battery charger are two
cord wrap cleats for storage of the clamp
cables.
To install, align the two tabs to correspond
with the two receptacles and push until you
hear a snap.
MINIMUM RECOMMENDED EXTENSION CORD
Length of Cord, in Feet
AWG* Size of Cord
25
18
50
16
100 150
12 10
*AWG=American Wire Gauge
PREPARING YOUR BATTERY TO BE CHARGED
It is important that you read and follow these guidelines while you are preparing to charge
the battery.
• Make sure that you have a 6 or 12 volt
lead-acid battery. Determine voltage of
battery by referring to vehicle owner’s
manual or the battery markings. Charge
battery initially at charger’s lowest rate.
• Take time to read all of the battery
manufacturer’s specific precautions,
such as removing or not removing vent
caps while charging, and recommended
rates of charge.
• Cleanthebatteryterminals.Becarefulto
keep corrosion from getting in or around
your eyes or on your hands.
• Be sure that the area around the bat-
tery is well ventilated while it is being
charged. Gas can be forcefully blown
away by using a piece of cardboard or
other nonmetallic material as a fan.
• Wearsafetyglasses.Seeadditional“Per-
sonal Safety Precautions” on page 4.
• If it is necessary to remove the battery
from the vehicle to charge it, always
remove the grounded terminal from the
battery first. Turn off all vehicle acces-
sories to avoid sparks from occurring.
• If required, for batteries with removable
ventcaps,adddistilledwatertoeachcell
until the battery acid reaches the level
recommendedbythemanufacturer.This
willhelppurgeexcessivegasesfromthe
cells.Becarefulnottooverfill.Ifyouhave
asealedbatterywithnon-removablevent
caps, no action is necessary.
• NOTE: A marine (boat) battery installed
in a boat must be removed and charged
on shore.
5
OPERATING INSTRUCTIONS
NOTE: A marine (boat) boat battery must be removed and charged on shore. To charge
it on board requires equipment specially designed for marine use.
IMPORTANT: Follow all safety instructions and precautions when charging your battery.
Wear complete eye protection and clothing protection. Charge your battery in a well-
ventilated area.
CHARGING BATTERY IN THE
VEHICLE:
part of the chassis or engine block,
away from the battery (see figure).
DO NOT connect clamp to negative
battery post, carburetor, fuel line or
sheet metal part.
1. Avoid personal injury by keeping clear
of fan blades, belts, pulleys and other
engine parts.
Connecting to a positive-grounded
system: Connect the black (NEGA-
TIVE) output clamp to the NEGATIVE
post of the battery. Rock and twist
the clamp back and forth to be sure
a solid electrical connection is made.
Then connect the red (POSITIVE)
output clamp to a heavy, unpainted
metal part of the chassis or engine
block, away from the battery. DO NOT
connect clamp to positive battery
post, carburetor, fuel line or sheet
metal part.
2. Avoid damaging the charger by keep-
ing the power cord and output cords
away from the hood, door or moving
engine parts.
3. Note the polarity of the battery posts
by checking the identification marks
on the battery: POSITIVE (POS, P or
+) and NEGATIVE (NEG, N or -). The
positive post is usually larger than the
negative post.
4. Identify which battery post is ground-
ed or connected to the chassis. THIS
IS NORMALLY THE NEGATIVE
POST.
6. Plug power cord into a 120V AC
2-prong wall outlet. The charger will
be set to the default state of 12V
REGULAR battery type, no charge
rate (tester mode).
7. Press the appropriate control buttons
to select the desired charge rate and
battery type. Within a few seconds,
the CHARGING (yellow) LED should
light and the charging process should
start. If the CHECK (red) LED is on,
check for correct cable connections.
8. To disconnect the charger, unplug
its power cord before attempting to
disconnect the output clamps. Then,
standing away from the battery, re-
move the output clamp from the chas-
sis or engine block. Finally, remove
the output clamp from the battery
post.
NEGATIVE GROUNDED SYSTEM
5. Connecting to a negative-grounded
system: Connect the red (POSITIVE)
output clamp to the POSITIVE post of
the battery. Rock and twist the clamp
back and forth to be sure a solid
electrical connection is made. Then
connect the black (NEGATIVE) output
clamp to a heavy, unpainted metal
9. Clean and store the charger in a dry
location.
6
USING ENGINE START
CHARGING BATTERY REMOVED
FROM THE VEHICLE:
Your battery charger can be used to jump
start your car if the battery is low. Fol-
low these instructions on how to use the
ENGINE START feature.
POSITIVE
NEGATIVE
RY
GER
BATTE
IMPORTANT: Follow all safety instructions
and precautions when charging your bat-
tery. Wear complete eye protection and
clothing protection. Charge your battery
in a well-ventilated area.
POWER
CORD
TO
GROUNDED
POWER
OUTLET
IMPORTANT: Using the ENGINE START
feature WITHOUT a battery installed in
the vehicle could cause damage to the
vehicle’s electrical system.
1. Note the polarity of the battery posts by
checkingtheidentificationmarksonthe
battery: POSITIVE (POS, P or +) and
NEGATIVE (NEG, N or -). The positive
post is usually larger than the negative
post.
2. Attach at least a 24-inch-long, 6-gauge
(AWG), insulated battery cable to
NEGATIVE (NEG, N or -) battery post.
Rockandtwisttheclampbackandforth
to be sure a solid electrical connection
is made.
3. Connect the red (POSITIVE) output
clamp to the POSITIVE battery post.
Rockandtwisttheclampbackandforth
to be sure a solid electrical connection
is made.
4. Position yourself as far away from the
battery as possible, and then connect
the black (NEGATIVE) output clamp to
the free end of the cable.
1. Forbatteryconnections,seepage6and
follow instructions 1 – 6 of CHARGING
BATTERY IN THE VEHICLE. With the
chargerpluggedinandconnectedtothe
battery of the vehicle, set the CHARGE
RATE to 75A START. Only the 75A
START, CHARGING, and VOLTAGE
LEDs should be lit, unless the 6V
REGULAR battery type has been se-
lected. In that case, the 6V REGULAR
LED will also be lit.
2. Crank the engine for no more than 5
seconds. If engine does not start, wait
3 minutes before cranking again.
3. Aftertheenginestarts,unplugthepower
cord before disconnecting the output
clamps from the battery.
4. Clean and store the charger in a dry
location.
5. Plug the power cord into a 120V AC
2-prongwalloutlet.Thechargerwillbeset
tothedefaultstateof12VREGULARbat-
tery type, no charge rate (tester mode).
6. Press the appropriate control buttons
to select the desired charge rate and
battery type. Within a few seconds, the
CHARGING (yellow) LED should light
and the charging process should start.
If the CHECK (red) LED is on, check for
correct cable connections.
7. To disconnect the charger, unplug its
powercordbeforeattemptingtodiscon-
nectthechargerclamps.Then,standing
away from the battery, remove the out-
put clamp from the NEGATIVE battery
post. Finally, remove the output clamp
from the POSITIVE battery post.
8. Clean and store the charger in a dry
location.
NOTE:Duringthestartingsequencelisted
above, the charger is set to one of three
states.
1. Wait for cranking - The charger waits
untiltheengineisactuallybeingcranked
before delivering 75 amps for engine
start. The charger delivers charge at a
rate of up to 12 amps while waiting and
will reset if the engine is not cranked
within 5 minutes. (If the charger resets,
it sets itself for a 2A charge and 12V
REGULAR battery.) While waiting for
cranking, the digital display shows
the battery voltage (it can’t be set to
percent).
2. Cranking - When cranking is detected,
the charger will automatically deliver
up to its maximum output (at least75A)
as required by the starting system for
7
up to 5 seconds or until the engine
cranking stops. The digital display
shows a countdown of the remaining
crank time in seconds. It starts at 5 and
counts down to 0.
the cool down period, no current is de-
livered to the battery. After 3 minutes,
the 75A START LED will stop blinking
andwilllightcontinuously,indicatingthat
anothercrankcyclecanbestarted.The
digital display will change from display-
ing the countdown back to displaying
the battery voltage. The CHARGING
LED will then be lit.
3. Cool Down - After cranking, the char-
ger enters a mandatory 3-minute (180
second) cool down state. During this
period, no settings can be changed.
The buttons are ignored. The digital
display indicates the remaining cool
down time in seconds. It starts at 180
and counts down to 0. The 75A START
LED blinks once every second. During
ENGINE STARTING NOTES:
• If the battery is disconnected during
the cool down period, the charger will
reset.
USING YOUR BATTERY CHARGER
OVERVIEW
a normal charge. If the charger detects a
sulfated battery, the charger will switch to
a special mode of operation designed for
such batteries. Activation of the special
desulfation mode is indicated by blinking
the CHARGING LED. If successful, nor-
mal charging will resume after the battery
is desulfated. The CHARGING LED will
then stop blinking and light continuously.
Desulfation could take up to 10 hours. If
desulfation fails, charging will be aborted
and the CHECK (red) LED will blink.
Using this battery charger is very simple.
First, connect the battery and AC power
following the precautions listed under
“OPERATING INSTRUCTIONS”. Then
select the appropriate BATTERY TYPE
and CHARGE RATE for your battery. The
charger will then do everything automati-
cally. This section explains a few details.
CHARGING: If the charger does not
detect a properly connected battery, the
CHECK (red) LED will light continuously
until such a battery is detected. Charging
will not begin while the CHECK LED is on.
When charging begins, the CHARGING
LED will be lit.
COMPLETION OF CHARGING:
Charge completion is indicated by
the CHARGED (green) LED; when
lit, the charger has stopped charging
and switched to the Maintain Mode of
operation.
AUTOMATIC SHUT OFF: When the 2A,
12A 30A charge rate is selected, the
charger is set to perform an automatic
charge. When an automatic charge is
performed, the charger stops charging au-
tomatically after the battery is charged.
MAINTAIN MODE: When the CHARGED
(green) LED is lit, the charger has started
Maintain Mode. This mode of operation is
also known as Float-Mode Monitoring. In
this mode, the charger keeps the battery
fully charged by delivering a small amount
of current, when necessary. The voltage
is maintained at a level determined by the
BATTERY TYPE selected.
ABORTED CHARGE: If charging can’t
be completed normally, charging will be
aborted. When charging is aborted, the
charger’s output is shut off and the red
CHECK LED and digital display blink on
and off (at opposite times). In that state, the
charger ignores all buttons. To reset from
after an aborted charge, either disconnect
the battery or unplug the charger.
GENERAL CHARGING NOTES:
The charger is designed to control its
cooling fan for efficient operation. Con-
sequently, it is normal for the fan to start
and stop when maintaining a fully charged
battery. The fan does not run in Tester
Mode.
DESULFATION MODE: If a battery is
left discharged for an extended period,
it could become sulfated and not accept
8
If the charge mode is changed after charg-
ing has started (by pressing the CHARGE
RATE or BATTERY TYPE button), the
charging process will be restarted.
The voltage displayed during charging is
the charging voltage and usually will be
higher than the battery’s resting voltage.
CHARGER CONTROLS
DISPLAY MODE SWITCH
With the exception of AGM and gel cell
batteries, all other battery types may or
may not have vent caps. Vent caps are
located on top of the battery and provide a
meanstoadddistilledwaterwhenneeded.
Batteriesshouldbemarkedwiththeirtype.
If charging a battery that is not marked,
check the manual of the item that uses
the battery. If the battery type is unknown,
use the REGULAR setting. Make sure the
batterycomplieswiththesafetyinstructions
on page 3.
Use this switch button to set the function of
the digital display to one of the following.
• BATTERY %: The digital display shows
an estimate of the percent of charge of
the battery connected to the charger
battery clamps.
• VOLTAGE:Thedigitaldisplayshowsthe
voltage at the charger battery clamps in
DC volts.
• ALTERNATOR %: The digital display
shows an estimated percentage of the
output of the vehicle charging system
connectedtothechargerbatteryclamps
as compared to a properly functioning
system.
CHARGE RATE SWITCH
Use this switch button to set the maximum
charge rate to one of the following.
• 2ASLOWCHARGERATE:Intendedfor
charging small batteries such as those
commonlyusedingardentractors,snow
mobiles and motorcycles. The 2A rate
is not intended to be used as a trickle
charger for larger batteries.
• 12A FAST 30A RAPID CHARGE
RATE: Use for charging automotive bat-
teries, marine batteries, and deep cycle
batteries. Not intended for industrial
applications.
BATTERY TYPE SWITCH
Use this switch button to set the type of
battery to be charged to one of the fol-
lowing.
• 12V REGULAR: This is the type of
battery usually used in cars, trucks,
and motorcycles. These batteries have
vent caps and are often marked “low
maintenance” or “maintenance-free”.
• 12V DEEP CYCLE: Deep cycle batter-
ies are usually marked as “deep cycle”
or “marine”. Deep cycle batteries are
usually larger than the other types.
• 12V AGM/GEL: AGM and gel cell bat-
teries have sealed cases without vent
caps. Such batteries are often smaller
than the other types.
• 75ASTART:Provides75ampsforcrank-
ing an engine with a weak or run down
battery. Always use in combination with
a battery.
NOTE: To turn OFF the charger, unplug
from the power cord from the wall outlet.
• 6V REGULAR: This is the type of bat-
tery usually used in antique and some
specializedvehicles.The6VREGULAR
batterytypeisnotselectableforbatteries
greater than 8.5V DC.
9
CONTROL PANEL GUIDE
10
USING THE BUILT-IN BATTERY TESTER
OVERVIEW
powered up, the battery will remain a
tester (not a charger) indefinitely, unless
a charge rate is selected.
This battery charger has a built-in battery
tester that displays either an accurate
battery voltage or an estimate of the
battery’s relative charge based on the
battery voltage and the Battery Council
International scale.
TESTING AFTER CHARGING
After the battery has been changed from
tester to charger (by selecting a charge
rate), it remains a charger. To change
the battery back to a tester, press the
CHARGE RATE switch until all charge
rate LEDs are off.
TESTING SEQUENCE
There are four basic steps required to
use the SC-7500A as a battery tester.
1. Connect the charger battery clamps to
the battery. Be sure to follow all of the
precautions listed under “OPERATING
INSTRUCTIONS”.
TESTER STATUS LEDs
When the SC-7500A is operating as
a battery tester, the status LEDs light
under the following conditions:
2. Connectthechargerpowercordtoa120V
AC 2-prong wall outlet.Again, be sure to
follow all of the precautions listed under
“OPERATING INSTRUCTIONS”.
3. If necessary, press the BATTERY
TYPE button until the correct type is
indicated.
4. Read the voltage on the digital display
or press the display mode button to set
the tester to BATTERY % and read the
battery percent.
• The CHARGED (green) LED will light if
a charged battery is tested.
• The CHARGING (yellow) LED does not
light in the battery test mode.
• The CHECK (red) LED lights unless a
properly connected battery is detected.
• When the tester display mode is set to
VOLTAGE,theCHARGEDandCHARG-
ING LEDs won't light.
INITIAL PERCENT CALCULATION
When a battery % is calculated for the
first time after connecting a battery, the
digital display will show three dashes
(“---”) for a period as long as several
seconds while the tester analyzes the
battery.
TESTER AND CHARGER
When first turned on, the SC-7500A oper-
ates only as a tester, not as a charger. To
continue to use it as only a tester, avoid
pressing the CHARGE RATE switch but-
ton. Selecting a charge rate activates the
battery charger and deactivates the tester.
Pressing the CHARGE RATE button when
the 75A Start LED is lit (except during the
180 second cool down) will shut off the
charger and activate the tester.
NOTES FOR TESTING BATTERY %
A recently charged battery could have a
temporarily high voltage due to what is
known as “surface charge”. The voltage
of such a battery will gradually drop during
the period immediately after the charging
system is disengaged. Consequently, the
tester could display inconsistent values
for such a battery. For a more accurate
reading, the surface charge should be
removed by temporarily creating a load on
the battery, such as by turning on lights or
other accessories.
POWER-UP IDLE TIME LIMIT
If no switch button is pressed within ten
minutes after the battery is first powered
up, the charger will automatically switch
from tester to charger, if a battery is
connected. In that case, the battery will
be set for the 2A charge rate and 12V
REGULAR battery type.
The battery % ranges from 0 to 100.
TESTER WITHOUT TIME LIMIT
The battery tester is only designed to test
batteries. Testing a device with a rapidly
changing voltage could yield unexpected
or inaccurate results.
If either the DISPLAY MODE or BAT-
TERY TYPE button is pressed within
the first ten minutes after the battery is
11
USING THE BUILT-IN ALTERNATOR TESTER
This battery charger has a built-in alter-
TESTER STATUS LEDs
nator tester that displays either an accu-
rate alternator voltage or an estimate of
the alternator’s relative output compared
to normal alternators. The Alternator %
values displayed should be taken as
general reference, not precise diagnosis.
The alternator tester functions the same
as the battery tester (see previous sec-
tion of this manual for details) with a few
differences.
When the SC-7500A is operating as an
alternator tester, the status LEDs light
under the following conditions.
• The CHARGED (green) LED will light
if the output of the charging system is
at the normally desired level.
• The CHARGING (yellow) LED does
not light in the alternator test mode.
• The CHECK (red) LED lights if the
VOLTAGE is much higher or lower
than normally desired.
TESTING SEQUENCE
There are three basic steps required to use
the SC-7500A as an alternator tester.
• When the tester display mode is set
to VOLTAGE, the CHARGED and
CHARGING LEDs won't light (it could
be testing a battery or an alternator).
1. Connect the charger battery clamps to
the battery or charging system. Be sure
to follow all of the precautions listed
under “OPERATING INSTRUCTIONS”.
2. Connect the charger power cord to a
120VAC 2-prong wall outlet. Again, be
sure to follow all of the precautions listed
under “OPERATING INSTRUCTIONS”.
3. Start the vehicle and turn on the
vehicle’s headlights. Read the voltage
on the digital display or press the
DISPLAY MODE button to set the
tester to ALTERNATOR % and read
the alternator percent.
ALTERNATOR TESTING NOTES
• The alternator percent display can
range from 0 to 199.
• The DISPLAY MODE cannot be set to
ALTERNATOR % during charging.
12
BATTERY PERCENT AND CHARGE TIME
This charger adjusts the charging time in
There are some important facts to keep in
mind when charging a battery.
order to charge the battery completely,
efficiently and safely. The microproces-
sor automatically makes the necessary
decisions. However, this section includes
guidelines that can be used to estimate
charging times.
• When the display indicates 77%
charged, the battery has been charged
enough to start most vehicles and has
already been charged as much as by
many other battery chargers.
The duration of the charging process de-
pends on three factors:
• When the display indicates 85%
charged, the battery has already been
charged at least as much as by most
other battery chargers.
1. Battery State – If a battery has only
been slightly discharged, it can be
charged in less than a few hours.
The same battery could take up to 10
hours if very weak. The battery state
can be estimated by using the built-in
tester (see page 11). The lower the
reading the longer charging will take.
• The battery % shown in tester mode
is an estimate based on the bat-
tery voltage and the Battery Council
International scale. The battery %
shown in charger mode is an estimate
of the relative charge in the battery
compared to the charge it should have
if the charging process is allowed to
complete.
2. Battery rating – A higher rated
battery will take longer to charge
than a lower rated battery under the
same conditions. A battery is rated in
ampere-hours (AH), reserve capacity
(RC) and cold cranking amps (CCA).
The lower the rating the quicker the
battery will be charged.
• The battery % shown in tester mode
can be used to estimate the relative
charge time. The lower the % shown,
the longer the charge time for a given
battery.
3. Charge rate – The charge rate is
measured in amps. This charger
provides charge rates of 2A, 12A
and 30A. The 75A rate is for engine
start only. The 2A rate is for charg-
ing smaller batteries such as those
used for motorcycles and garden
tractors. Such batteries should not be
charged using the 12A or 30A rate.
The 12A and 30A rates are for charg-
ing larger batteries. In the 30A mode,
the charger begins at a low charge
rate and increases the charge rate if
it is determined that the battery can
accept the higher rate. All charging
modes will decrease the charge rate
as the battery approaches maximum
charge. After the charging process
has started, the digital display can be
used to determine charging progress
by selecting the BATTERY % mode.
• The battery % shown in charger mode
is an indication of the relative progress
of the charging process. The higher
the battery % displayed, the less
charge time remains.
• The more a battery is discharged,
the faster it absorbs charge from a
charger. That means that the battery
% increases faster at the beginning
of the charging process than at the
end. In other words, it takes longer
for the battery to absorb the last few
percent of charge than the first several
percent.
13
CHARGING TIPS
Read this entire manual before using your charger. The tips below serve only as a guide
for specific situations.
If your vehicle won’t start:You don’t need
to fully charge a battery to start your ve-
hicle. If the charger won’t start your vehicle
using the 75ASTART rate, try charging the
battery using the 12A 30A rate for 10
or 15 minutes. That should charge the bat-
tery enough to allow the 75A START rate
to start the vehicle. If the vehicle will then
be operated continuously for an extended
period (such as a long drive), the vehicle
could charge the battery back to normal
during that period. If the vehicle will only
be operated for a short period (short drive),
the battery might need to be charged again
before it could start the vehicle again.
Reviving your battery: If you only wish
to charge your battery enough to operate
your vehicle, you don’t need to wait for the
entire charging process to be completed.
When the charger displays a battery %
of 77 or more (see page 13), the battery
has usually been charged enough for the
vehicle to start and operate normally.
Completing an interrupted charge: If
the charging process has been interrupted
and restarted after the charger displays a
battery % of 85 or more, the charger could
go straight to Maintain Mode (see page 8).
However, if the original charge was started
using 12A 30A, the charge can often
be completed using the 2A rate.
MAINTENANCE AND CARE
A minimal amount of care can keep your battery charger working properly for years.
1. Clean the clamps each time you are finished charging. Wipe off any battery fluid
that may have come in contact with the clamps to prevent corrosion.
2. Coil the input and output cords neatly when storing the charger. This will help pre-
vent accidental damage to the cords and charger.
3. Occasional cleaning of the case of the charger with a soft cloth will keep the finish
shiny.
14
TROUBLESHOOTING
Performance problems often can be corrected by the user. Please read through this chart
for a possible solution to common problems.
PROBLEM
POSSIBLE CAUSE
SOLUTION
The battery is connected
and the charger is on,
but isn't charging.
The charger is in tester
mode, not charger mode.
Press the CHARGE
RATE button to activate
charging and select a
charge rate.
Indicator lights are lit in
an erratic manner not
explained in the “Using
Your Battery Charger”
section.
You might have acciden-
tally activated a special
diagnostic mode.
Make sure nothing is
touching the control
panel, then unplug the
charger and plug it in
again.
The charger may be
defective.
Return to place of pur-
chase for replacement.
The CHECK (red) LED
always flashes before
the battery is completely
charged.
The incorrect BATTERY
TYPE may have been
selected.
Reset the charger by
unplugging it or briefly
disconnecting it or briefly
disconnecting the nega-
tive battery clip. Select
the desired CHARGE
RATE and BATTERY
TYPE again, if neces-
sary.
This will happen if the
battery did not reach full
charge within 24 hours.
May be due to a very
large battery or a bank
of batteries requiring
more power than a 30/12
Amp charger can deliver
within 24 hours. The bat-
tery may also be faulty.
Engine crank time is less
than specified.
Starter motor may be
drawing more than 80
Amps.
Charge the battery at the
12A 30A rate for 10
to 15 minutes then crank
the engine.
The green CHARGED
LED lights a few minutes
after connecting to the
battery.
The battery may be
fully charged or recently
charged, leaving the bat-
tery voltage high enough
to appear to be fully
charged.
If the battery is in a ve-
hicle, turn the headlights
on for a few minutes
to reduce the battery
voltage and try charging
again.
The incorrect BATTERY
TYPE may have been
selected.
Reset the charger by un-
plugging it or briefly dis-
connecting the negative
battery clip. Select the
desired CHARGE RATE
and BATTERY TYPE
again, if necessary.
15
WARRANTY
SCHUMACHER ELECTRIC CORPORATION,
801 BUSINESS CENTER DRIVE,
MOUNT PROSPECT, ILLINOIS 60056-2179
MAKES THIS LIMITED WARRANTY TO THE ORIGINAL PURCHASER AT RETAIL OF
THIS PRODUCT. THIS LIMITED WARRANTY IS NOT TRANSFERABLE.
Schumacher Electric Corporation warrants this battery charger for one year from date of
purchase at retail against defective material or workmanship. If such should occur, the
unit will be repaired or replaced at the option of the manufacturer. It is the obligation of
the purchaser to forward the unit together with proof of purchase, transportation and/or
mailing charges prepaid to the manufacturer or its authorized representative.
This limited warranty is void if the product is misused, subjected to careless handling, or
repaired by anyone other than the manufacturer or its authorized representative.
The manufacturer makes no warranty other than this limited warranty and expressly
excludes any implied warranty including any warranty for consequential damages.
THIS IS THE ONLY EXPRESS LIMITED WARRANTYAND THE MANUFACTURER NEI-
THER ASSUMES NOR AUTHORIZES ANYONE TO ASSUME OR MAKE ANY OTHER
OBLIGATION TOWARDS THE PRODUCT OTHER THAN THIS EXPRESS LIMITED
WARRANTY. THE MANUFACTURER MAKES NO WARRANTY OF MERCHANTABIL-
ITY OR FITNESS FOR PURPOSE OF THIS PRODUCTAND EXPRESSLY EXCLUDES
SUCH FROM THIS LIMITED WARRANTY.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES OR LENGTH OF IMPLIED WARRANTY SO THE
ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTSAND YOU MAYALSO HAVE
OTHER RIGHTS THAT VARY FROM STATE TO STATE.
WARRANTY VALIDATION: The enclosed “Warranty Validation Card” must be completed
and mailed within 10 days of product purchase to activate this limited warranty.
16
|