Oricom Secure 700 User Manual

TM  
Baby Monitor  
Secure 700  
User Guide  
SAFETY INFORMATION 1  
The installation location plays a decisive role in ensuring  
proper operation. Therefore, maintain a distance of at  
1 Safety Information  
least one meter from other electronic equipment, such as  
microwave ovens or hi−fi devices, otherwise they could  
cause mutual interference/faults.  
Please read this operating instruction manual thoroughly.  
Intended use  
Prevent excessive exposure to smoke, dust, vibration,  
chemicals, moisture, heat and direct sunlight. Do not use  
the equipment in potentially explosive areas.  
The surveillance system has been developed to monitor  
rooms. The baby unit sends acoustic and video signals  
from its point of installation to the parent unit. Any other  
use is considered unintended use.  
Power adapter plug  
The use of this equipment does not substitute personal  
supervision, e.g. of a child. Users are not relieved of their  
personal liability. Unauthorised modification or reconstruction  
is not permitted. Under no circumstances open the device or  
complete any repair work yourself.  
ATTENTION  
Only use the power adapter plugs supplied since other  
power adapter plugs could damage the surveillance  
system. Ensure access to the power adapter plug is not  
obstructed by furniture or such.  
!
Installation location and safety information  
Never lay the baby unit in a baby’s/child’s bed or playpen.  
Ensure that the baby unit and power cable are out of reach  
of babies/children, i.e. they are at least one meter away.  
Pay attention that the components are sufficiently well−  
ventilated when in operation. Do not lay a cushion, towel or  
such over the devices.  
The devices are not intended for medical purposes.  
Warning and signal tones from respiratory or heartbeat  
monitoring equipment are not transmitted.  
2 SAFETY INFORMATION  
devices in a separate waste container. The adjacent  
symbol indicates that the device must not be disposed of in  
normal domestic waste!  
Rechargeable batteries  
ATTENTION  
Batteries represent a hazard to health and  
the environment! Never open, damage or  
swallow batteries or allow them to pollute the  
environment.  
Never throw batteries into a fire. Only use batteries of the  
same type! Pay attention to correct polarity.  
!
Power failure  
They may contain toxic, ecologically hazardous heavy  
metals.  
In the event of a power failure, the devices only operate  
through battery power.  
You are legally obliged to dispose of power packs and  
batteries at the point of sale or in the corresponding  
containers provided at collection points provided by local  
public waste authorities. Disposal is free of charge. The  
adjacent symbols indicate that the batteries must not  
be disposed of in normal domestic waste and must be  
brought to collection points provided by local public waste  
authorities.  
Disconnect the power adapter plugs from the devices in  
this case.  
Medical equipment  
ATTENTION  
Never use the devices in the vicinity of medical  
equipment. Effects on such equipment cannot be fully  
ruled out.  
!
Packaging materials must be disposed of according to  
local regulations.  
Disposal  
In order to dispose of your device, take it to a  
collection point provided by your local public waste  
authorities (e.g. recycling centre). According to laws  
on the disposal of electronic and electrical devices, owners  
are obliged to dispose of old electronic and electrical  
GETTING TO KNOW YOuR SC700 3  
1
2
3
4
Antenna  
2 Getting to know your SC700  
Sound level LEDs  
Play / Pause  
Lullaby selector  
Talk button  
The buttons in this operating manual are subsequently  
depicted with a uniform contour. Therefore, slight  
deviations in the appearance of the symbols on the buttons  
compared to those depicted here are possible.  
5
6
7
Menu button  
VOX LED  
Monitor unit (Parent Unit)  
8
9
10  
11  
12  
Loudspeaker  
Microphone  
Power LED  
On/Off switch  
Reduce volume and brightness / menu options  
selection  
1
2
3
13  
12  
13  
12  
11  
3
4
14  
4
5
13  
Increase volume and brightness / menu options  
selection  
6
7
10  
9
14  
15  
16  
17  
Belt clip/Support  
Battery compartment  
Charger  
15  
8
17  
Charge contacts  
16  
4 GETTING TO KNOW YOuR SC700  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
Night light  
Light sensor  
Power LED  
Microphone  
Lens  
Antenna  
Loudspeaker  
Temperature sensor  
Socket for power adapter plug  
ON/OFF switch  
Battery compartment  
Camera unit (baby Unit)  
18  
23  
19  
24  
22  
21  
27  
20  
25  
26  
28  
26  
uSING YOuR SC700 5  
Operating with batteries (not supplied)  
3 Installation  
Use a small screwdriver to open the baby  
Insert the batteries, paying attention to  
correct polarity. Refer to the diagrams in  
the battery compartment. Close the battery  
compartment again.  
Safety information  
ATTENTION  
It is essential to read the Safety Information in Chapter 1  
before using your SC700.  
!
The baby unit is operated by means of 4 AAA Alkaline batteries  
(not contained in the material supplied). The baby the power  
adapter plug.  
Checking the package contents  
In the case of a low battery charge, the Power LED flashes  
slowly. The batteries must be replaced,  
The package contains:  
One monitor unit One rechargeable  
Operating with a power adapter plug  
One camera unit  
baby unit  
(parent unit) with  
belt clip/support  
battery for the  
parent unit  
Connect the baby unit as illustrated in the diagram. For  
safety reasons, only use the power adapter plug supplied.  
One power  
One charger with  
adapter plug for power adapter plug  
The baby unit for the parent unit  
An operating  
manual  
Connecting and aligning the baby unit  
ATTENTION  
Position the baby unit with a minimum distance of 1 m  
!
to other electronic devices, otherwise there is a risk of  
mutual disturbance. Point the upper section of the baby  
unit towards the baby or object you want to monitor.  
Check that the baby or object is suitably displayed on the  
parent unit.  
Mains power outlet  
6
Connecting the parent unit  
The parent unit is powered by a 3.6 V, 930 mAh battery pack.  
The rechargeable battery pack can be recharged directly in  
the parent unit when it is inserted in the charging station. The  
Power LED lights up red when the parent unit is being charged.  
In the case of a low battery charge, the Power LED flashes  
slowly. The battery pack must then be recharged.  
ATTENTION  
Position the parent with a minimum distance of 1 m to  
other electronic devices, otherwise there is a risk.  
!
Using the belt clip/support  
Operating with a power adapter plug  
You can use the belt clip/support as a belt clip by turning it  
upwards.  
Connect the parent unit as illustrated in the diagram. For  
safety reasons, only use the power adapter plug supplied.  
When tuned downwards, it can be used as a support to  
keep it in a standing position.  
Important Note  
Mains power outlet  
Operation with rechargeable batteries  
Before using your SC700 for the first time, please charge  
the batteries in the parent unit for a minimum of 14 hours.  
This will help to increase the performance of your battery.  
6. Turn the belt clip upwards.  
7. Open the battery compartment on the rear side of the  
parent unit.  
8. Insert the batteries, paying attention to correct polarity.  
9. Close the battery compartment again.  
10.Turn the belt clip back downwards.  
OpERATING ThE BABY uNIT 7  
Connecting and aligning the baby unit  
ATTENTION  
4 Operating the baby Unit  
Check the baby unit and parent unit are working properly each  
time before the equipment is put into operation.  
Position the baby unit with a minimum distance of 1 m  
to other electronic devices, otherwise there is a risk of  
mutual disturbance. Point the upper section of the baby  
unit towards the baby or object you want to monitor.  
Check that the baby or object is suitably displayed on the  
parent unit.  
!
Switching the baby unit on/off  
Position the baby unit in a good position for the monitoring  
tasks required and align the camera lens to the area to be  
monitored.  
Night vision  
Slide the switch to ON.  
The baby unit is equipped with 8 infrared diodes. This  
enables the transmission of pictures from areas which  
are not illuminated. The night vision function is activated  
automatically when the light conditions make it necessary.  
The Power LED lights up green. The baby unit is  
now ready to operate.  
To switch the unit off, slide the switch to OFF.  
In the case of a low battery voltage, the Power LED flashes  
slowly.  
When the night−time vision function is activated, the screen  
In this event replace the 4 x AAA batteries with fresh alkaline  
batteries.  
display on the parent unit turns to black and white.  
8 OpERATING ThE pARENT uNIT  
Press this button twice.  
5 Operating the Parent Unit  
This icon appears in the display for a few seconds.  
Use the button to set temperature measurement to  
OFF, °C or °F.  
Check the baby unit and parent unit are working properly each  
time before the equipment is put into operation.  
18°C The current temperature is displayed during the  
temperature measurement, e.g. in °C.  
Switching the parent unit on/off  
Press and hold this button until you hear 2 acoustic  
signals. The logo appears first then the image being  
taken by the baby unit camera.  
Press and hold the button for approx. 1 second to  
switch the unit off.  
Switching this night light on/off  
Press the button three times.  
This icon appears in the display for a few seconds.  
Use this button to switch the night light on the baby  
unit on or off.  
In the case of a low battery charge, the Power LED flashes  
slowly.  
Operating the Parent unit  
Adjusting the VOX1 sensitivity  
The VOX1 function (sound detection) causes the  
system to start transmitting automatically from the  
baby unit to the parent unit immediately a voice or  
sound is detected.  
Setting the brightness  
Press the button once.  
This icon appears in the display for a few seconds.  
Use this button to adjust the brightness to one of five  
settings.  
Press this button four times.  
This icon appears in the display for a few seconds.  
Adjusting the temperature measurement  
IMPORTANT INFORMATION  
Use this button to set VOX to OFF or adjust the  
sensitivity to one of 5 levels. When one of the five  
levels has been set, the VOX LED lights up red and  
the display goes out after 10 seconds.  
The ideal temperature for a baby to sleep is 16° - 18 °C. Please  
set or adjust the room temperature accordingly.  
The display is reactivated when a sound is detected  
pACK CONTENTS 9  
or a button on the parent unit is pressed.  
Registration  
1 VOX: Voice Operated Transmission = Sound detection  
The parent unit and baby unit are pre−registered.  
If necessary, registration can also be completed  
manually:  
Baby unit/Parent unit  
1 Switch the baby unit off. Switch set to OFF.  
2 Cover the light sensor with a black cloth and switch  
the baby unit on. Position ON.  
3 With the parent unit switched on press and hold  
this button on the parent unit for a few seconds.  
Selecting a lullaby  
Press the button on the right hand side of the parent  
unit.  
This icon appears in the display.  
Use the button to select one of the 5 lullabies (1-5).  
If no number is displayed, all of the lullabies will  
continue to play in sucession until deactivated.  
Use this button to adjust the volume to one of five  
settings. The volume levels will be adjusted on both  
the baby unit and parent unit simultaneously.  
C1  
4 This icon appears in the display.  
5 The Power LED on the baby unit flashes quickly  
for approx. 15 seconds.  
This icon appears during the volume adjustment.  
6 Press this button to confirm the selection.  
Intercom function  
7 C1.... appears initially, then C1....OK.  
Press and hold the button.  
This icon appears in the display.  
Speak into the microphone to talk with the person  
near the other unit.  
When a connection is established, the image viewed  
by the lens appears in the display.  
If C1...X appears (registration failed), it may be  
necessary to remove the power and remove the  
batteries from the baby unit for a few seconds.  
While talking, any lullabies playing are muted.  
Range  
This icon flashes in the display when the distance  
between the baby unit and parent unit is too great.  
Move the parent unit nearer to the baby unit.  
10 FAuLT FINDING  
Beeping noise − Increase the distance between  
6 Customer Support  
( a c o u s t i c  
feedback)  
parent unit and baby unit.  
− Reduce the volume on the parent  
unit.  
Should you experience difficulties operating the SC700  
please refer to the problems and solutions guide below.  
If you still experience difficulties please contact Oricom  
Customer Support on 1300 889 785 for assistance.  
Noise  
− The battery power is too low.  
Picture but no − Volume setting is too low.  
sound  
Problems and solutions  
transmission  
Problems  
Solutions  
Picture is in − The night vision function is active.  
b l a c k a n d  
white  
The battery pack − The power adapter plug is not  
in the  
Equipment does − Baby unit and/or parent unit are not  
not function  
No reception  
switched on.  
The batteries are empty or  
defective.  
− The power adapter plugs are not  
connected.  
− Baby unit and parent unit are not  
registered.  
connected.  
parent unit is not  
charged  
− The parent unit and baby unit are  
too far apart.  
− The VOX sensitivity is set too low.  
R e c e p t i o n − The parent unit and baby unit are  
interference  
too far apart.  
− The battery power is too low.  
Other electronic devices are  
causing interference in the field of  
transmission.  
TEChNICAL SpECIFICATIONS 11  
F r e q u e n c y 2.4 GHz  
range  
7 Technical Specifications  
Technical data  
Permissible am- 0°C to 40°C  
bient tempera-  
ture  
Feature  
Value  
Camera (baby Socket: 6 V DC  
unit) Sensor: 1 night light sensor  
IR diodes: 8  
Monitor (parent Screen: 2,4" LC display  
unit) Socket: 6 V DC  
Power supply Power adapter plug, input:  
Transmission 15 ~ 17 dBm  
power (TX PA  
power)  
(parent unit)  
100-240 VAC, 50-60Hz, 150 mA  
Power adapter plug, output:  
6 VDC, 800 mA  
or rechargeable battery NiMH  
3.6 V , 950 mAh  
Initial charging Up to 16 h  
time for battery  
Power supply Power adapter plug, input:  
(baby unit)  
100-240 VAC, 50-60Hz, 150 mA  
Power adapter plug, output:  
6 VDC, 800 mA  
or 4 AAA Alkaline batteries  
Range  
Up to 150 meters under optimum  
conditions.  
Range is reduced in buildings  
through  
walls, doors etc.  
12 GuARANTEE  
Warranty (Australia)  
(a) Warranty Oricom International Pty Ltd (Oricom) warrants that  
the product is free from defects in materials and workmanship  
for a period of 12 months effective from the date of purchase.  
This warranty in no way affects your statutory warranty under  
the Trade Practices Act 1974 or any other similar legislation.  
It is important that you read the Warranty Card as it contains  
full and additional details of the warranty, limitation of warranty  
and conditions for receiving the warranty services during the  
warranty period. The Warranty Card is located in the package.  
Oricom will not be liable for consequential losses including loss of  
profits arising from a cause of action in contract, tort or any other  
statutory or common law (except where a statute or any law prohibits  
this exclusion). The warranty does not extend to damage caused by  
misuse, negligence, excessive voltage or lightning. This warranty in  
no way affects your statutory rights. Full details of the warranty are  
contained in the enclosed warranty card.  
Customer Support  
(b) Exclusion and limitation of liability. Oricom will not be in  
breach of a warranty or condition expressly stated in this User  
Guide or the Warranty Card or implied by the Trade Practices  
Act and excludes any liability arising under any statutory or  
common law for damages or any other remedy if the damage  
occurs as a result of:  
If you feel this product is not working correctly please consult  
the user guide and ensure that you are using the product in  
accordance with the instructions.  
To order spare parts additional parent units, replacement parts  
and in case of any technical issues you may have with this  
product please consult our website for further information or send  
us an email for a prompt response to your enquiry.  
(i) Failure by you to follow the instructions in the User Guide  
for the installation and proper functioning of the product;  
(ii) Negligence on your part or misuse by you of the product;  
In the unlikely event of a fault developing, please contact us  
for assistance. If the product is then found to be faulty you will  
be asked to return it directly to us with a copy of the purchase  
receipt.  
(iii) Any un-controlled external cause to the product not  
functioning including but not limited to electricity failure,  
lighting, over voltage;  
(iv) Non adherence by you to the warnings in the User Guide  
and the User Guide generally; and  
(v) Modification to the product or services carried out to the  
product by anyone other than Oricom or on Oricom's  
behalf.  
(vi) Batteries supplied with this product are covered under this  
warranty for a period of 90 days.  
Australia  
Oricom International Pty Ltd  
Locked Bag 658  
Customer Support  
Phone: 1300 889 785  
South Windsor, NSW 2756  
Fax: +61 2 4574 8898  
New Zealand  
Baby First Limited  
Customer Support  
Email: admin@babyfirst.co.nz  
Phone: 0800 429329  
TM  

Toshiba Air Conditioner Rav Sm804bt Tr User Manual
Sharp Af S80ex User Manual
Sanyo C2472 User Manual
Sanyo 26khh72r User Manual
Philips 3121 233 42852 User Manual
Panasonic Kx Tca391aln User Manual
HITACHI 51SWX20B User Manual
Defiant Battery Powered Motion Light User Manual
BROTHER HL 3170CDW User Manual
ACER AS317 User Manual