Omega 22040c User Manual

Operating Instructions & Parts Manual  
Long Chassis Hydraulic Service Jacks  
Capacity  
4 Ton  
Model  
22040C, 22041C  
22050C, 22051C  
22100C, 22101C  
5 Ton  
10 Ton  
Models 22040C, 22050C & 22100C  
Models 22041C, 22051C & 22101C (Air Options)  
U.S. Patent No's. 5,755,099 • 5,946,912 • 5,341,723  
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.  
Obey all safety messages that follow this symbol to avoid possible injury or death.  
!
! ADVERTENCIA  
! WARNING  
To avoid crushing and related injuries:  
• Leer, comprender, y seguir las instrucciónes antes  
de utilizar el aparato.  
NEVER work on, under or around a  
load supported only by a hydraulic  
jack. ALWAYS use adequately rated  
jack stands.  
• El manual de instrucciónes y la información de  
seguridad deben estar comunicado en lengua del  
operador antes del uso.  
• No seguir estas indicaciónes puede causar daños  
personales o materiales.  
SFA Companies  
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.  
Printed in China  
22040C-M1 rev 06/08  
Release Valve  
(Handle Knob)  
Lift Control Valve  
(for air actuated models only)  
Handle  
Saddle  
Handle Position Lock  
Front Wheel  
Oil Filler Plug/Screw  
(on Reservoir)  
Handle Sleeve  
Foot Pedal  
Grease Fitting  
Rear Caster  
Figure 1 - Typical Long Chassis Jack Nomenclature (22051C shown)  
PREPARATION  
Assembly  
Always secure the handle into the handle sleeve by means of the bolt lock washer and nut provided. Tighten securely  
to prevent accidental removal of handle while in use.  
Before Use  
1. Verify that the product and application are compatible, if in doubt call Omega Technical Service (888) 332-6419.  
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the  
product, its components and recognize the hazards associated with its use.  
3. To familiarize yourself with basic operation, turn the release valve (handle knob):  
a. Clockwise until firm resistance is felt to further turning. This is the ‘CLOSED’ release valve position used to  
raise the saddle.  
b. Counter-clockwise, but no more than 1/2 turn from the closed position. This is the ‘OPEN’ release valve  
position used to lower the saddle.  
4. With saddle fully lowered, locate and remove cover plate, then remove the oil filler plug/screw. Pump 6 to 8 full  
strokes. This will help release any pressurized air which may be trapped within the reservoir. Check oil level. Proper  
oil level will vary from just covering the ram cylinder to 3/16” above it as seen from the oil filler hole. Reinstall the  
oil filler plug/screw.  
5. For air option models 22041C, 22051C & 22101C, Pour a teaspoon of good quality, air tool lubricant into the air supply  
inlet of the lift control valve. Connect to air supply and operate for 3 seconds to evenly distribute lubricant.  
Note: These models are equipped with the popular 1/4" NPT air coupler. When installing a different air coupler of  
your choice, ensure that thread tape or compound is used when servicing connections. To ensure dependable,  
trouble free operation an inline air dryer and oiler is recommended.  
6. Ensure that jack rolls freely. Raise and lower the unloaded saddle throughout the lifting range before putting into  
service to ensure the pump operates smoothly. Replace worn or damaged parts and assemblies with Omega  
authorized replacement parts only.  
Bleeding / Venting Trapped Air  
With the release valve in the OPEN position (3b.) and with saddle fully lowered, locate and remove the oil filler plug/  
screw. Pump 6 to 8 full strokes. This will help release any pressurized air which may be trapped within the reservoir.  
Reinstall the oil filler plug/screw.  
3
! WARNING  
! WARNING  
Study, understand, and follow all printed  
materials provided with/on this product before use.  
X
Do not exceed rated capacity.  
• Use only on hard, level surface.  
This is a lifting device only!  
To avoid crushing and related injuries:  
Never work on, under or around a load supported  
only by hydraulic jack.  
Immediately after lifting, support the load with  
a pair of appropriately rated jack stands.  
Always use adequately rated jack stands.  
• Chock each unlifted tire in both directions.  
Do not use this device to lift, level, lower, support nor  
move a house, mobile home, travel trailer, camper or  
any building structure.  
Be alert and sober when using this product. Do not  
operate under the influence of drugs or alcohol.  
• Lift only on areas of the vehicle as specified by  
the vehicle manufacturer.  
• Never wire, clamp or otherwise disable the lift  
control valve to function by other than operator's  
hand.  
Do not move or dolly the vehicle while on the jack.  
• No alterations shall be made to this product.  
• Failure to heed these markings may result in  
personal injury and/or property damage.  
OPERATION  
Lifting  
Only attachments and/or adapters supplied by the manufacturer shall be used. Lift only on area of the  
vehicle as specified by the vehicle manufacturer.  
!
Note: The jack is equipped with handle position lock. To adjust the handle, release lock device by pulling the lever  
up, then back until lever is locked into place.  
1. Follow the vehicle manufacturer’s recommended guidelines for lifting. Engage the emergency brake and chock  
each unlifted wheel in both directions to prevent inadvertent vehicle movement.  
2. Locate and close the release valve by turning the release valve knob clockwise until firm resistance is felt.  
3. Refer to the vehicle manufacturer owner’s manual to locate approved lifting points on the vehicle. Center jack  
saddle under lift point.  
4. Verify lift point, then pump handle or foot pedal to contact lift point. To lift, pump handle or squeeze lift control valve  
(models 22041C, 22051C & 22101C) until load reaches desired height. Never use foot pedal to raise load.  
5. Transfer the load immediately to appropriately rated jack stands.  
NEVER use hydraulic jack as a stand alone device! ALWAYS transfer the lifted load IMMEDIATELY to a  
pair of appropriately rated jack stands. Use one pair of jack stands per vehicle. Rated capacity is per  
pair only! Do not exceed rated capacity.  
!
Lowering  
Be sure all tools and personnel are clear before lowering load. Slowly open the release valve! The more  
you turn the release valve knob counter-clockwise, the faster the load will come down. Maintain control  
of the rate of speed at which the load lowers at all times!  
!
1. Raise load high enough to clear the jack stands.  
2. Remove jack stands carefully. (always used in pairs).  
3. Slowly turn the release valve knob counter-clockwise, but no more than 1/2 full turn. If the load fails to lower:  
a. Use another jack to raise the vehicle high enough to reinstall jack stands.  
b. Remove the malfunctioning jack and then the jack stands.  
c. Use the functioning jack to lower the vehicle.  
4. After removing jack from under the vehicle, fully lower the saddle to reduce ram exposure to rust and  
contamination.  
4
Lubrication  
MAINTENANCE  
A periodic coating of light lubricating oil to pivot points,  
axles and hinges will help to prevent rust and assure  
that wheels, casters and pump assemblies move freely.  
To help ensure trouble free operation, an inline air dryer  
and oiler is recommended.  
Important: Use ONLY good grade hydraulic jack oil.  
Avoid mixing different types of fluid and Never use  
brake fluid, turbine oil, transmission fluid, motor oil or  
glycerin. Improper fluid can cause failure of the jack and  
the potential for sudden and immediate loss of load. We  
recommend Mobil DTE 13M.  
Cleaning  
Periodically check the pump piston and ram for signs  
of rust or corrosion. Clean as needed and wipe with  
an oily cloth.  
Adding oil  
1. With saddle fully lowered set jack in its upright, level  
position. Locate and remove oil filler plug/screw.  
2. Fill with oil until ~3/16" above the inner cylinder as  
seen from the oil filler hole. Reinstall the oil filler  
plug/screw.  
Note: Never use sandpaper or abrasive material on  
these surfaces!  
Storage  
Changing oil  
When not in use, store the jack with saddle fully  
For best performance, replace the complete fluid supply  
at least once per year.  
lowered.  
1. With saddle fully lowered, remove the oil filler plug/  
screw.  
2. Lay the jack on its side and drain the fluid into a  
suitable container.  
REPLACEMENT PARTS  
(refer to page 6 thru12)  
Not all components of the jack are replacement  
items, but are illustrated as a convenient reference of  
location and position in the assembly sequence. When  
ordering parts, give Model number, serial number and  
parts description. Call or write for current pricing: SFA  
Companies, 10939 N. Pomona Ave. Kansas City, MO  
64153, U.S.A. Tel:(888)332-6419 Fax:(816)891-6599  
Note: Dispose of hydraulic fluid in accordance with  
local regulations.  
3. Fill with oil until ~3/16" above the inner cylinder as  
seen from the oil filler hole. Reinstall the oil filler  
plug/screw.  
TROUBLESHOOTING  
Symptom  
Possible Causes  
Corrective Action  
Jack will not lift load  
• Release valve not tightly closed  
• Overload condition  
• Ensure release valve tightly closed  
• Remedy overload condition  
• Air pressure inadequate  
• Ensure adequate air pressure  
Jack will lift, but not maintain  
pressure  
• Release valve not tightly closed  
• Hydraulic unit malfunction  
• Ensure release valve tightly closed  
• Discontinue use, contact Omega  
technical service  
Jack will not lower after unloading • Reservoir overfilled  
• Linkages binding  
• Drain fluid to proper level  
• Clean and lubricate moving parts  
• Ensure proper fluid level  
• Fluid level low  
Poor lift performance  
• Fluid level low  
Air trapped in system  
• Ensure proper fluid level  
• With ram fully retracted, remove oil  
filler plug/screw to let pressurized  
air escape. Reinstall oil filler plug/  
screw  
Will not lift to full extension  
• Fluid level low  
• Ensure proper fluid level  
5
Replacement parts illustration for Model 22040C  
25  
23  
37  
24  
26  
38  
27  
44  
21  
39  
3
16  
17  
F
40  
31  
J
19  
2
E
D
6
18  
C
B
A
G
7
4
1
5
H
30  
11  
8
I
12  
14  
41  
9
45  
13  
15  
43  
42  
Figure 2 - Replacement Parts Illustration for Model 22040C  
6
Replacement parts illustration for Model 22041C  
23  
37  
24  
25  
26  
17  
38  
27  
44  
28  
21  
39  
3
16  
29  
F
40  
31  
J
19  
2
E
D
18  
36  
34  
C
B
6
35  
A
32  
G
7
1
10  
5
H
33  
8
I
41  
9
4
30  
14  
11  
15  
43  
13  
42  
Figure 3 - Replacement Parts Illustration for Model 22041C  
7
Replacement Parts List for Models 22040C & 22041C:  
Item  
1
22040C Part#  
22041C Part#  
Description  
Filter  
Qty  
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
2
1
1
1
1
-
G251-20008-000  
2
G423-20003-000  
5905-00100-100  
5901-00071-000  
Reservoir  
3
Filler Plug  
4
O-ring, D7.1x2.65  
Release Valve  
Hyd. Cartridge  
Washer  
5
G251-20004-000  
G250-20004-000  
6
G100-43000-000  
B300-14002-000  
G651-31002-000  
G651-31001-000  
7
8
Pump Cylinder  
Pump Piston  
Hyd. Cartridge  
Universal Joint  
Spring  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
21  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
-
N/A  
G100-44000-000  
G423-70000-000  
N/A  
G423-30000-000  
G251-00005-000  
5405-12039-000  
Pin  
5405-02028-000  
G423-40000-000  
G100-00015-000  
5102-06015-000  
G251-00009-000  
G251-00010-000  
G423-00011-000  
G423-00013-000  
5111-55020-000  
G423-00010-000  
G251-40001-000  
5402-04028-000  
Retaining Pin  
Piston Link  
Return Spring, Pedal  
Screw  
Foot Pedal  
Handle Fork  
Return Spring  
Saddle  
Screw, Philips  
Cover  
Knob  
Spring Pin  
A070-40009-000  
Hose clip  
N/A  
5110-04012-000  
5107-05016-000  
G423-60000-000  
A20060-0006  
Screw, Philips  
Screw  
5110-05025-000  
G423-20000-000  
Hyd. Power Unit  
Air Hose  
A27060-0003  
Air Motor  
N/A  
A20060-0007  
Lift Control Valve  
Hose Assembly  
Quick coupler, Male  
Handle Assembly  
Front Wheel Assembly  
Caster Assembly  
Bolt Assembly  
Pump Assembly  
Pin  
A20060-0015  
A20060-0016  
G251-40000-000  
G100-90009-K01  
G423-90004-K01  
G250-90004-K02  
G250-90009-K03  
G651-31000-000  
5405-12050-000  
5307-00012-000  
5404-04030-000  
Washer  
Retaining Pin  
Nut  
5205-00005-000  
N/A  
G4230S-088 (includes 3,4 & A to J)  
Seal Kit for Hyd. Unit  
Seal Kit for Air Motor  
Piston for Air Motor  
Label (s)  
-
A27010-0000  
N/A  
-
A270-01100-0000  
22041C-L0  
-
22040C-L0  
-
22040C-M0  
Manual  
-
8
Replacement parts illustration for Models 22050C & 22051C  
Figure 4 - Replacement Parts Illustration for Model 22050C & 22051C  
9
Replacement Parts List for Models 22050C & 22051C:  
Item  
1
2
3
4
5
6
7
8
22050C  
22051C  
Description  
Filter  
Reservoir  
Filler Plug  
O-ring, D7.1x2.65  
Release Valve  
Hyd. Cartridge  
Washer  
Pump Cylinder  
Pump Piston  
Hyd. Cartridge  
Universal Joint  
Spring  
Qty  
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
2
2
2
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
-
G251-20008-000  
G250-20002-000  
5905-00100-200  
5901-00071-000  
G250-20004-000  
G250-24000-000  
B300-14002-000  
G651-31002-000  
G651-31001-000  
G250-23000-000  
G250-30000-000  
G251-00005-000  
5405-12036-000  
5405-02028-000  
G250-50000-000  
G251-00004-000  
5110-06016-000  
G251-00009-000  
G251-00010-000  
5304-00018-000  
G251-00003-000  
5304-00028-000  
G251-00002-000  
5110-06010-000  
G250-00002-000  
G251-40001-000  
5402-04028-000  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
-
Pin  
Retaining Pin  
Piston Link  
Return Spring, Pedal  
Screw  
Foot Pedal  
Handle Fork  
Snap Ring  
Return Spring  
Snap Ring  
Saddle  
Screw, Philips  
Cover  
Knob  
Spring Pin  
Hose clip  
Screw, Philips  
Screw  
Hyd. Power Unit  
Air Hose  
N/A  
A070-40009-000  
5110-04012-000  
5105-05012-000  
G250-70000-000  
G250-20000-000  
A20060-0006  
A27060-0003  
A20060-0007  
A20060-0015  
A20060-0016  
Air Motor  
N/A  
Lift Control Valve  
Hose Assembly  
Quick coupler, Male  
Handle Assembly  
Front Wheel Assembly  
Caster Assembly  
Bolt Assembly  
Pump Assembly  
Handle Grip  
Seal Kit for Hyd. Unit  
Seal Kit for Air Motor  
G250-40000-000  
G250-90004-K01  
G250-90004-K02  
G250-90009-K03  
G651-31000-000  
G251-00007-000  
G2501S-074 ( includes 3,4 & A to J)  
-
-
-
A27010-0000  
A270-01100-0000 Piston for Air Motor  
N/A  
22050C-L0  
22051C-L0  
Label (s)  
-
22040C-M0  
Manual  
-
Seal Kit (G2501S-074)Contents:  
Item Description  
Qty  
Item Description  
Qty  
1
1
1
2
3
4
Filler Plug  
1
1
2
1
1
1
E
F
G
H
I
Back-up Washer  
O-ring, D53x5  
Packing  
O-ring, D15x2.65  
Back-up Washer  
O-ring, D7.1x2.65  
O-ring, D116x4  
O-ring, D73.8x3.5  
Back-up Washer  
U-cup  
A
B
C
D
2
1
J
Packing (for 22050C only)  
10  
Replacement parts illustration for Models 22100C & 22101C  
Figure 5 - Replacement Parts Illustration for Model 22100C & 22101C  
11  
Replacement Parts List for Models 22100C & 22101C:  
Item  
1
22100C  
22101C  
Description  
Filter  
Qty  
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
1
1
2
1
2
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
-
G251-20008-000  
2
G100-40003-000  
G62S-03301-000  
5901-00071-000  
G251-20004-000  
G100-43000-000  
B300-14002-000  
G651-31002-000  
G651-31001-000  
G100-44000-000  
G100-90009-K04  
5405-12039-000  
5404-02028-000  
G100-70000-000  
G100-00015-000  
5402-05025-000  
G251-00009-000  
G251-00010-000  
5304-00018-000  
G100-00014-000  
5305-00024-000  
G100-90009-K02  
5111-55022-000  
G100-00016-000  
G251-40001-000  
5402-04028-000  
Reservoir  
3
Filler Screw  
O-ring, D7.1x2.65  
Release Valve  
Hyd. Cartridge  
Washer  
4
5
6
7
8
Pump Cylinder  
Pump Piston  
Hyd. Cartridge  
Universal Joint  
Pin  
9
10  
11  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
-
Retaining Pin  
Piston Link  
Return Spring, Pedal  
Pin  
Foot Pedal  
Handle Fork  
Snap Ring  
Return Spring  
Snap Ring  
Saddle Assy.  
Screw, Philips  
Cover  
Knob  
Spring Pin  
A070-40009-000 Hose clip  
N/A  
5110-04012-000  
5110-05025-000  
Screw, Philips  
Screw  
G100-80000-000  
G100-40000-000 Hyd. Power Unit  
A20060-0006  
A27060-0003  
A20060-0007  
A20060-0015  
A20060-0016  
Air Hose  
Air Motor  
N/A  
Lift Control Valve  
Hose Assembly  
Quick coupler, Male  
Handle Assembly  
Front Wheel Assembly  
Caster Assembly  
Bolt Assembly  
G100-90009-K01  
G100-90004-K02  
G661-70000-000  
G250-90009-K03  
G651-31000-000  
G251-00007-000  
Pump Assembly  
Handle Grip  
G1001S-98  
G1000S-98  
A27010-0000  
Seal Kit for Hyd. Unit  
Seal Kit for Air Motor  
-
N/A  
-
A270-01100-0000 Piston for Air Motor  
-
22100C-L0  
22101C-L0  
Label (s)  
-
22040C-M0  
Manual  
-
12  

Sharp Mx M450 User Manual
Sharp Ar C160 User Manual
Sanyo Twicell Hf B1u User Manual
Philips Silver 389 User Manual
Philips Sbcsc465 User Manual
Mitsubishi Electronics Pffy Nemu A User Manual
LG DLEX2650 User Manual
HAMILTON BEACH DURATHON 19801 CCC User Manual
Defiant Dual Brite Motion Security Light User Manual
ACER ASPIRE 5 A514 54G User Manual