Mini Print Server
MODEL PS101
Installation Guide
Introduction
Thank you for purchasing a NETGEAR PS101
Mini Print Server. With this print server you can
share your printer with all the computers in your
home or office that run Microsoft® Windows®
95 OSR2, 98, 2000, NT 4.x, Me, or XP
operating system.
This installation guide shows you how to connect
the print server to your printer and configure it to
use with your computers. Setup is easy – if you
follow the instructions in this guide, the print server
will soon be up and running for your computers.
If you have problems, there is a troubleshooting section on page 9 to help you. You can get
more detailed troubleshooting information from the Reference Manual on the CD or online at
Installation Procedure Overview
Estimated time: 30 minutes
1. Unpack the box and verify the contents.
2. Connect the print server to the printer and to the network.
3. Configure the print server to be recognized on the network.
4. Configure each computer to print through the print server.
Note: You only need to go through procedures 1 through 3 once. Repeat procedure
4 for each computer that will share the printer with the print server. It takes less
than 5 minutes to configure and test each computer.
On the PS101 Resource CD, you will find a Reference Manual containing more detailed
information about installation, troubleshooting and configuration.
1
Unpack the Box and Verify the Contents
1
PS101 Mini
Print Server
Power adapter
PS101 Mini Print Server Resource CD,
installation guide, support information
card & warranty/registration card
When you open the box, verify that you received everything.
The package includes:
•
•
•
•
•
•
PS101 Mini Print Server
AC power adapter
PS101 Resource CD, including a full Reference Guide and print server software
PS101 Installation Guide (this document)
Warranty and registration card
Support information card
2
Connect the Print Server
The PS101 Mini Print Server connects directly to the Centronics parallel port on your
printer. After connecting it to your printer, you then connect the print server to a
network device (like a hub, router, or switch).
2
Before you share the printer with the NETGEAR PS101 Mini
Print Server, you should have at least one computer connected
to an Ethernet network and have one unused port on an
Ethernet hub, switch, or router.
Centronics parallel port on the printer
Note: For printers with a Mini-
Centronics C port, you will need to use
one of the other NETGEAR Print
Not Compatible with
Servers such as the PS111W, PS110 or
PS113 along with the correct cable.
Mini Centronics-C Printers
Note: The procedures described in this guide are for a
TCP/IP-based network environment. For NetBEUI
protocol printing, please see the Reference Manual.
ETHERNET
9V DC
LINK ALERT
Printer with PS101
attached
1. With the printer turned off, connect the print server to
the Centronics connector on the printer.
2. Insert one end of an Ethernet patch (or straight-through)
cable into an open Ethernet port in the network device
(hub, switch, or router) and insert the other end into the
Ethernet port on the print server.
Note: You may use a Category 3 (or higher)
Ethernet cable.
3. Turn the printer on.
4. Connect the power adapter’s cord into the back
of the print server and then plug the adapter into a
power source (such as a wall socket or power strip).
ETHERNET
9V DC
LINK ALERT
Printer with PS101 attached
Netgear Router
When power has been applied to the print server:
DSL modem
The LINK light (green) should light up and may
blink to show network activity.
The ALERT light (yellow) should be off.
Note: If any light does not operate as indicated,
go to the Troubleshooting section on page 9.
3
Install Printer Server Software and
Setup the Print Server
3
The PS101 comes with several software components that allow you to set up the
print server and use administrative tools. You should install all the software onto one Windows
computer to act as the print server administrator. For the other computers, only install the
NETGEAR Add Printer Wizard as described in procedure 4.
To install the NETGEAR Print Server software:
1. Insert the PS101 Printer Server Resource CD in
the CD-ROM drive. NETGEAR Print Server
Software Installation wizard starts up
automatically. If it doesn’t, double-click My
Computer, double-click your CD-ROM drive,
and double-click Setup.exe.
2. Follow the instructions in the installation wizard
to install the software.
3. For the administrative computer, install all components.
Note: If this computer will just use the printer, only select the NETGEAR Add
Printer Wizard. See procedure 4: Configure a Computer To Access the Print Server
for details.
4. Click Finish.
To set up the print server:
1. Click Start. Point to Programs and click NETGEAR Print Server>NETGEAR Print Server
Setup Wizard.
2. Follow the instructions in the installation wizard to set up the print server.
\If you have questions, click Help for information about a specific screen.
4
Note: The PS101 Print Server, by default, automatically obtains an IP address from
the network. However, NETGEAR recommends you use a fixed IP address to be
able to use a Web browser to print a test page or to make configuration changes
later. For a home or small office, use IP address information compatible with your
router setup. The IP address for the print server needs to be unique in the network.
If you don’t know what to use, you may click Suggest New Values to get a useable
IP address. If you are using a NETGEAR router with default settings, the following
settings should work:
IP address: 192.168.0.150 (The first three numbers should match the
numbers for the network device. Make sure the last 3 digits are unique
on your network.)
Subnet mask: 255.255.255.0
Gateway IP address: 192.168.0.1 (the address of your router)
3. When complete, click Finish.
4. When asked if you want to set up a printer right away, click Yes and continue to
procedure 4: Confirgure a Computer To Access the Print Server. You have already completed
the software installation and are running the NETGEAR Add Printer Wizard.
Advanced Settings
Advanced users may want to change the default name of the Print Server or make other
changes in the settings. There are 2 ways to administer your NETGEAR Print Server. The
Reference Manual on the Resource CD has full instructions.
a. Open a Web browser and go to the IP address for the print server. (For example, type
b. You can use the NETGEAR Print Server Administration program. Click Start. Point to
Programs and click NETGEAR Print Server>NETGEAR Print Server Administration.
5
Configure a Computer To Access the
Print Server
Before using the PS101 on your network, each computer that needs to access the print server
must have:
4
•
•
•
A connection to the network.
The printer added using the NETGEAR Add Printer Wizard.
Either the printer driver software already installed or, if this is a new printer, access to the
printer driver software (either on a CD or downladed to a disk).
To install the Add Printer Wizard (for a non-administrative
computer):
Note: You can skip ahead “To configure
computers...” if you have already installed the
NETGEAR software on this computer.
1. Insert the PS101 Printer Server Resource CD in
the CD-ROM drive. NETGEAR Print Server
Software Installation wizard starts up
automatically. If it doesn’t, double-click My
Computer, double-click your CD-ROM drive,
and double-click Setup.exe.
2. Follow the instructions in the installation wizard to
install the software.
3. When asked, select only the NETGEAR Add Printer Wizard.
4. Click Finish.
6
To configure computers running Windows NT, 2000, and XP:
1. Click Start, point to Programs> NETGEAR Print Server and click NETGEAR Add Printer
Wizard.
2. Read, follow the instructions, and click OK in the Setup
message window.
3. In the list, select the print server port with the printer
you want to add to this computer and click Add. When
you see the AddPort screen, write down the port name
(such as PSFF0091_P1).
Printer port name:_____________________________.
4. Scroll down in Add Printer Wizard screen. Select the Print
Server port with port name as written above.
Click Next.
Note: Do NOT select the default port “LPT1.”
5. Select the printer manufacturer on the left and
the model on the right
or, if you need to install the printer driver, click
Have Disk and follow the instructions.
6. If you have installed the printer driver for this
printer, you will be asked to keep the existing
driver or replace it. Select either one and click
Next. Follow the instruction on screen if any.
7. Type a name for this printer and determine whether you want this as the default printer.
Click Next.
8. Select No when asked about sharing the printer and click Next.
Note: The print server will perform this function.
9. Select Yes when asked about printing a test page and click Next.
10. Click Finish.
If you cannot print the test page, go to Troubleshooting on page 9.
If you successfully printed the test page, you can configure other computers to access this
printer by repeating procedure 4 on each computer.
7
To configure computers running Windows 95, 98, and Me:
1. Click Start, point to Programs> NETGEAR Print Server and click NETGEAR Add Printer
Wizard.
2. Read, follow the instructions, and click OK in the Setup message window.
3. Select the port with the printer you connect and click
Add in the Printer Select screen. When the AddPort
screen shows, write down the port name ( such as
PSFF0091_P1).
Printer port name: _____________________________.
4. Select the printer manufacturer on the left and the model
on the right or, if you need to install the printer driver,
click Have Disk and follow the instructions.
5. Click Next and select the print server in the
Available ports list. This should match the port
name from step 3. Then click Next.
Note: Do NOT select the default port “LPT1.”
6. Type a name for this printer and determine
whether you want this as the default printer.
7. Select Yes when asked about printing a test page.
8. Click Finish.
If you cannot print the test page, go to Troubleshooting on page 9.
If you successfully printed the test page, you can configure other computers to access this
printer by repeating procedure 4 on each computer.
8
Troubleshooting
The LINK light is not lit
The print server has no power.
•
•
Make sure the power adapter is properly connected to the print server.
Make sure the power adapter is properly connected to a functioning power outlet. If it is
in a power strip, make sure the power strip is turned on. If it is plugged directly into the
wall, verify that it is not a switched outlet.
•
Make sure you are using the correct NETGEAR power adapter supplied with your
print server.
The printer is not on or there is a connection problem.
•
•
Make sure the printer is turned on.
Make sure the connector is securely plugged in at the print server and the printer.
There is a network hardware connection problem.
•
Make sure the connectors are securely plugged in at the print server and the network
device (hub, switch, or router).
•
•
Make sure the network device is turned on.
Be sure the correct cable is used. In most instances, use a Category 3 (or higher) Ethernet
patch cable. If the network device has Auto Uplink (MDI/MDIX) ports, you may use a
™
cross-over cable.
The ALERT light is lit.
•
Turn the printer off and unplug the print server’s power adapter. Turn the printer on and
then plug in the print server’s power adapter.
•
Contact NETGEAR if this doesn’t solve the problem.
9
I can not print from my computer
•
You may not have selected the correct printer in the Print dialog box.
•
You may not have configured the computer to work with the print server. Go through
procedure 4 on page 6 for each computer that will use the print server.
•
The computer may not be communicating to the print server. To test for printing directly
from the print server:
1. Open a browser and go to the IP address for the print server. (For example, type
Note: If you do not know the IP address, you use the NETGEAR Print Server
Administration program. Click Start. Point to Programs and click NETGEAR Print
Server>NETGEAR Print Server Administration. The Reference Manual on the
Resource CD has full instructions.
2. Click Printer Ports on the left.
3. Click Print Test Page.
4. After the test page prints, click Logout.
5. Click Yes (or OK) if asked about closing the browser window.
Could print previously but can no longer print from
my computer
•
If the print server is set up to ‘obtain IP address automatically’, the IP address may have
changed. Restart your computer. You may also use the IP Setup program on the
administrative computer to assign a fixed IP address to the print server. Click Start. Point
to Programs and click NETGEAR Print Server>IPSetup.
•
The print server may be overheated. Unplug the power adapter and then plug it in again.
Remove any paper or other material that may be restricting ventilation. Lower the
temperature in the surrounding environment.
10
Glossary of Terms
Category 3 (CAT3): A twisted pair cable that meets specified requirements for 10 Mbps
networking up to 328 ft. (100m).
Category 5 (CAT5): A shielded twisted pair cable that meets requirements for 10 and 100 Mbps
networking up to 328 ft. (100m).
Local Area Network (LAN): A communications network within a limited area, such as one
building.
TCP/IP: Transfer Control Protocol (TCP) with Internet Protocol (IP). The main
internetworking protocol used in the Internet.
Mini Print Server System Requirements
•
•
•
Windows 95 OSR2, 98, Me, NT 4.x, 2000, XP
A printer with a Centronics parallel port
Network software
11
Mini Print Server Specifications
Network Protocols: IEEE 802.3i, 10BASE-T CSMA/CD Interface, NetBEUI and TCP/IP
Electromagnetic Emissions: CE mark, commercial; FCC Part 15, Class A; EN 55 022
(CISPR 22), Class A; VCCI Class A ITE; EN50082-1, C-Tick N10947
Safety Agency Approvals: CE mark, commercial, UL listed, CSA certified, TUV licensed, T-Mark
Dimensions
Width 1.3 in. (6.2 cm)
Height 0.8 in. (2.0 cm)
Depth 2.3 in. (6.0 cm)
Weight 0.4 lb. (0.1 kg)
Status LEDs
Link and Alert lights
Power Adapter
9 V DC, 0.50A (customized power plug for individual countries)
Environmental Specifications
Operating temperature
Operating humidity
Warranty
32˚ to 104˚ F (0˚ to 40˚ C)
10 to 90%, noncondensing
Limited 2-year warranty
12
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice. NETGEAR does not assume any liability
that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the Model PS101 Mini Print Server has been suppressed in accordance with the conditions set
out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992.The operation of some equipment (for example, test
transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the
notes in the operating instructions. Federal Office for Telecommunications Approvals has been notified of the placing
of this equipment on the market and has been granted the right to test the series for compliance with the regulations.
VCCI Statement
This equipment is in the Class A category (information equipment to be used in a residential area or an adjacent area
thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing
Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas. When used
near a radio or TV receiver, it may become the cause of radio interference. Read instructions for correct handling.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures: (1) Reorient or relocate the receiving antenna, (2)
Increase the separation between the equipment and receiver, (3) Connect the equipment into
an outlet on a circuit different from that to which the receiver is connected, (4) Consult the
dealer or an experienced radio/TV technician for help.
EN 55 022 Statement
This is to certify that the Model PS101 Mini Print Server is shielded against the generation of radio interference in
accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the
application of EN 55 022 Class A (CISPR 22). Compliance is dependent upon the use of shielded data cables.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (Model PS101 Mini Print Server) does not exceed the Class A limits for radio-noise emissions
from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (Model PS101 Mini Print Server) respecte les limites de bruits radioélectriques visant les
appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des
Communications du Canada.
April 2002
13
|