NEC MULTISYNC X841UHD 2 User Manual

Large Format Display

User’s Manual

MultiSync X841UHD-2

MultiSync X981UHD-2

Please ﬁnd your model name in the label on the backside of monitor.

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

U.S. Responsible Party: NEC Display Solutions of America, Inc.

Address:

500 Park Boulevard, Suite 1100

Itasca, Illinois 60143

(630) 467-3000

Tel. No.:

Type of Product:

Display Monitor

Equipment Classiﬁcation: Class B Peripheral

Model: MultiSync X841UHD-2 (X841UHD-2)

MultiSync X981UHD-2 (X981UHD-2)

We hereby declare that the equipment speciÞed above

conforms to the technical standards as speciÞed in the FCC Rules.

FCC Information

1. Use the attached speciﬁed cables with this color monitor so as not to interfere with radio and television reception.

(1) Please use the supplied power cord or equivalent to ensure FCC compliance.

(2) Please use the supplied shielded video signal cable.

2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.

The user may ﬁnd the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify

and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Ofﬁce, Washington,

D.C., 20402, Stock No. 004-000-00345-4.

Windows is a registered trademark of Microsoft Corporation.

NEC is a registered trademark of NEC Corporation.

OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and

Switzerland.

DisplayPort and DisplayPort Compliance Logo are trademarks owned by the Video Electronics Standards

Association.

All other brands and product names are trademarks or registered trademarks of their respective owners.

HDMI, the HDMI logo and High-Deﬁnition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC

in the United States and other countries.

Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and

areas.

CRESTRON and ROOMVIEW are registered trademarks of Crestron Electronics, Inc. in the United States and other countries.

GPL/LGPL Software Licenses

The product includes software licensed under GNU General Public License (GPL), GNU Lesser General Public License (LGPL),

and others.

For more information on each software, see “readme.pdf” inside the “about GPL&LGPL” folder on the supplied CD-ROM.

English-1

Important Information

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT

USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE

PRONGS CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM

WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER

CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have sufﬁcient magnitude to cause electric

shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has

been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION: Please use the power cord provided with this monitor in accordance with the table below. If a power cord is not

supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the

AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.

European

Continental

Plug Type

North America

U.K.

Chinese

Japanese

Plug Shape

U.S.A./

Canada

Region

Voltage

EU (except U.K.)

230

U.K.

230

China

220

Japan

100

Taiwan

110

120*

* When operating the MultiSync monitor with its AC 125-240V power supply, use a power supply cord that matches the power

supply voltage of the AC power outlet being used.

NOTE:

This product can only be serviced in the country where it was purchased.

Use the power cord which has BSMI mark at both ends when you use this monitor in Taiwan.

•

The intended primary use of this product is as an Information Technical Equipment in an ofﬁce or domestic environment.

The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.

English-2

Safety Precautions, Maintenance & Recommended Use

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE

FOLLOWING WHEN SETTING UP AND USING

THE MULTI-FUNCTION MONITOR:

Connecting to a TV*

•

Cable distribution system should be grounded (earthed) in

accordance with ANSI/NFPA 70, the National Electrical Code

(NEC), in particular Section 820.93, Grounding of Outer

Conductive Shield of a Coaxial Cable.

•

DO NOT OPEN THE MONITOR. There are no user

serviceable parts inside and opening or removing covers may

expose you to dangerous shock hazards or other risks. Refer

all servicing to qualiﬁed service personnel.

•

The screen of the coaxial cable is intended to be connected

to earth in the building installation.

•

Do not bend, crimp or otherwise damage the power cord.

Immediately unplug your monitor from the wall outlet and refer

servicing to qualiﬁed service personnel under the following

conditions:

Do not place any heavy objects on the power cord.

Damage to the cord may cause shock or ﬁre.

•

The power supply cord you use must have been approved

by and comply with the safety standards of your country.

(Type H05VV-F 3G 1mm²should be used in Europe).

•

When the power supply cord or plug is damaged.

If liquid has been spilled, or objects have fallen into the monitor.

If the monitor has been exposed to rain or water.

•

In UK, use a BS-approved power cord with molded plug

having a black (13A) fuse installed for use with this monitor.

If the monitor has been dropped or the cabinet damaged.

If you notice any structural damage such as cracks or

unnatural wobbling.

The power cable connector is the primary means of detaching

the system from the power supply. The monitor should be

installed close to a power outlet, which is easily accessible.

•

If the monitor does not operate normally by following

operating instructions.

•

Do not spill any liquids into the cabinet or use your monitor

near water.

Recommended Use

•

Do not insert objects of any kind into the cabinet slots,

as they may touch dangerous voltage points, which can

be harmful or fatal or may cause electric shock, ﬁre or

equipment failure.

For optimum performance, allow 20 minutes for warm-up.

Rest your eyes periodically by focusing on an object at least

5 feet away. Blink often.

•

Position the monitor at a 90° angle to windows and other light

sources to minimize glare and reﬂections.

•

Do not place this product on a sloping or unstable cart, stand

or table, as the monitor may fall, causing serious damage to

the monitor.

Clean the LCD monitor surface with a lint-free, non-abrasive

cloth. Avoid using any cleaning solution or glass cleaner!

Do not mount this product upside down for an extended

period of time as it may cause permanent damage to the

screen (X841UHD-2).

Adjust the monitor’s brightness, contrast and sharpness

controls to enhance readability.

Do not mount this product face down or upside down for an

extended period of time as it may cause permanent damage

to the screen (X981UHD-2).

Avoid displaying ﬁxed patterns on the monitor for long

periods of time to avoid image persistence (after image

effects).

Do not place any objects onto the monitor and do not use the

monitor outdoors.

•

Get regular eye checkups.

Ergonomics

•

If glass is broken, handle with care.

Do not cover vent on monitor.

To realize the maximum ergonomic beneﬁts, we recommend the

following:

If monitor or glass is broken, do not come in contact with the

liquid crystal and handle with care.

•

Use the preset Size and Position controls with standard

signals.

•

Allow adequate ventilation around the monitor, so that heat

can properly dissipate. Do not block ventilated openings or

place the monitor near a radiator or other heat sources.

Do not put anything on top of the monitor.

•

Use the preset Color Setting.

Use non-interlaced signals.

Do not use primary color blue on a dark background, as

it is difﬁcult to see and may produce eye fatigue due to

insufﬁcient contrast.

•

Do not move or mount this product by hanging a rope or wire

to the backside handle.

Do not mount or secure this product by using the backside

handle. It may fall and cause personal injury.

Cleaning the LCD Panel

•

When the liquid crystal panel is dusty, please gently wipe

with a soft cloth.

•

Handle with care when transporting. Save packaging for

transporting.

•

Please do not rub the LCD panel with hard material.

Please do not apply pressure to the LCD surface.

If using the cooling fan continuously, it is recommended to

wipe holes clean a minimum of once a month.

Please clean the holes of back cabinet to reject dirt and dust

at least once a year because of set reliability.

Please do not use OA cleaner as it will cause deterioration or

discolor on the LCD surface.

When using a LAN cable, do not connect to a peripheral

device with wiring that might have excessive voltage.

Cleaning the Cabinet

•

Unplug the power supply

Do not use monitor in high temperature, humid, dusty, or oily

areas.

Gently wipe the cabinet with a soft cloth

To clean the cabinet, dampen the cloth with a neutral detergent

and water, wipe the cabinet and follow with a dry cloth.

Do not use monitor under rapid temperature and humidity

change condition or avoid cold air from air-conditioning outlet

directly, as it may shorten the lifetime of the monitor or cause

condensation. If condensation happens, let the monitor stand

unplugged until there is no condensation.

NOTE: DO NOT clean with benzene thinner, alkaline detergent,

alcoholic system detergent, glass cleaner, wax, polish

cleaner, soap powder, or insecticide. Rubber or vinyl

should not be in contact with the cabinet for an extended

period of time. These types of ﬂuids and materials can

cause the paint to deteriorate, crack or peel.

* The product you purchased may not have this feature.

English-3

Contents

Your new MultiSync monitor box* should contain the following:

•

LCD monitor

Power cord*¹

•

Setup Manual

Clamp x 1

Video Signal Cable (DisplayPort cable)

Video Signal Cable (Mini DisplayPort to DisplayPort cable)

Wireless Remote Control and AAA Batteries

Screw with washer (M4 x 10) x 1

CD-ROM

Video Signal Cable

(DisplayPort cable)

Video Signal Cable

(Mini-DisplayPort to

DisplayPort cable)

Screw with washer

(M4 x 10) x 1

Clamp x 1

Power Cord*¹

Setup Manual

CD-ROM

Setup Manual

Wireless Remote Control

and AAA Batteries

Remember to save your original box and packing material to transport or ship the monitor.

Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than one

power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been approved by

and complies with the safety standard of your particular country.

English-4

Installation

This device cannot be used or installed without the Tabletop

Stand or other mounting accessory for support. For proper

installation it is strongly recommended to use a trained,

NEC authorized service person. Failure to follow NEC

standard mounting procedures could result in damage to the

equipment or injury to the user or installer. Product warranty

does not cover damage caused by improper installation.

Failure to follow these recommendations could result in

voiding the warranty.

Orientation

•

When using the display in the portrait position, the

monitor should be rotated clockwise so that the left side

is moved to the top, right side is moved to the bottom.

This will allow for proper ventilation and will extend the

lifetime of the monitor. Improper ventilation may shorten

the lifetime of the monitor.

Mounting

DO NOT mount the monitor yourself. Please ask your dealer.

For proper installation it is strongly recommended to use

a trained, qualiﬁed technician. Please inspect the location

where the unit is to be mounted. Mounting on wall or ceiling

is the customer’s responsibility. Not all walls or ceilings are

capable of supporting the weight of the unit. Product warranty

does not cover damage caused by improper installation,

remodelling, or natural disasters. Failure to comply with these

recommendations could result in voiding the warranty.

DO NOT block ventilated openings with mounting

accessories or other accessories.

For NEC Qualiﬁed Personnel:

LED Indicator

To ensure safe installation, use two or more brackets to

mount the unit. Mount the unit to at least two points on the

installation location.

•

When using the display in the portrait position, handles

and NEC logo plate position can be changed.

1. Changing handles position.

Please note the following when mounting

on wall or ceiling

For landscape position:

X841UHD-2:

X981UHD-2:

•

When using mounting accessories other than those that

are NEC approved, they must comply with the VESA-

compatible (FDMlv1) mounting method.

•

NEC recommends mounting interfaces that comply with

UL1678 standard in North America.

NEC strongly recommends

using size M8 screws

Mounting

Bracket

Unit

No gap

(15-17 mm + thickness

of bracket and washers in

length). If using screws

longer than 15-17 mm,

check the depth of the hole.

(Recommended Fasten

Force: 1125 - 1375N•cm).

No thread

6 mm

Washers

under

ꢀ 10 mm

Screw

15-17 mm

Thickness

of bracket

and washers

For portrait position:

X841UHD-2:

Bracket hole should be under ꢀ 10 mm.

X981UHD-2:

•

Prior to mounting, inspect the installation location to

insure that it is strong enough to support the weight of the

unit so that the unit will be safe from harm.

•

Refer to the instructions included with the mounting

equipment for detailed information.

Make sure there is no gap between the monitor and the

bracket.

English-5

2. Changing NEC logo plate position.

Removing the logo plate: Insert a thin stick (less than 2 mm

diameter) into the hole in the bottom of logo plate and

remove the logo plate by pushing it up from the bottom.

Attaching Mounting Accessories

The monitor is designed for use with the VESA mounting

system.

1. Attach eyebolts (not included) for

mounting

Attaching the logo plate: Hook the part (1) of logo plate into

the bezel and press in.

This model is equipped with attachable eyebolts to aid in

mounting.

•

Screw the eyebolts into eyebolt holes as shown in the

picture.

2 mm

•

Be sure eyebolts are secure.

In order to move the monitor into position, use a lifting

device attached to the eyebolts.

DO NOT mount the monitor using only the eyebolts.

X841UHD-2:

Eyebolt (M10) (not included)

Eyebolt Hole

Mounting location

•

The ceiling and wall must be strong enough to support the

monitor and mounting accessories.

X981UHD-2:

Eyebolt (M10) (not included)

DO NOT install in locations where a door or gate can hit

the unit.

DO NOT install in areas where the unit will be subjected

to strong vibrations and dust.

Eyebolt Hole

DO NOT install near where the main power supply enters

the building.

Do not install in where people can easily grab and hang

onto the unit or the mounting apparatus.

Landscape

When mounting in a recessed area, as in a wall, leave at

least 4 inches (100 mm) of space between the monitor

and the wall for proper ventilation.

Portrait

•

Allow adequate ventilation or provide air conditioning

around the monitor, so that heat can properly dissipate

away from the unit and mounting apparatus.

2. Attach Mounting Accessories

Be careful to avoid tipping monitor when attaching

accessories.

Mounting on ceiling

VESA Mounting Interface (M8)

•

Ensure that the ceiling is sturdy enough to support the

weight of the unit and the mounting apparatus over time,

against earthquakes, unexpected vibrations, and other

external forces.

•

Be sure the unit is mounted to a solid structure within

the ceiling, such as a support beam. Secure the monitor

using bolts, spring lock washers, washer and nut.

DO NOT mount to areas that have no supporting internal

structure. DO NOT use wood screws or anchor screws for

mounting. DO NOT mount the unit to trim or to hanging

ﬁxtures.

Maintenance

400 mm

•

Periodically check for loose screws, gaps, distortions,

or other problems that may occur with the mounting

apparatus. If a problem is detected, please refer to

qualiﬁed personnel for service.

Mounting accessories can be attached with the monitor in

the face down position. To avoid damaging the screen face,

place the protective sheet on the table underneath the LCD.

The protective sheet was wrapped around the LCD in the

original packaging. Make sure there is nothing on the table

that can damage the monitor.

•

Regularly check the mounting location for signs of

damage or weakness that may occur over time.

English-6

When using mounting accessories other than NEC compliant

and approved, they must comply with the VESA-compatible

mounting method.

5. Ventilation Requirements

When mounting in an enclosed space or recessed area,

leave adequate room between the monitor and the enclosure

to allow heat to disperse, as shown below.

NOTE:

Prior to installation, be sure to place the monitor

on a ﬂat area with adequate space.

3. Using Option Board

1. Turn off the main power switch.

2. Remove the attached slot cover by unscrewing the

installed screws (Figure 1).

3. Insert option board in to the monitor. Attach the slot cover

by using the removed screws.

NOTE:

Please contact your supplier for available option

boards.

Do not apply excessive force to manipulate the

optional board before ﬁxing it with screws.

Allow adequate ventilation or provide air conditioning around

the monitor, so that heat can properly dissipate away from

the unit and mounting apparatus; especially when you use

monitors in multiple screen.

NOTE:

The sound quality of the internal speakers will

differ according to the acoustics of the room.

6. Prevent Tipping

When using the display with the optional table top stand

fasten the LCD to a wall using a cord or chain that can

support the weight of the monitor in order to prevent the

monitor from falling. Fasten the cord or chain to the monitor

using the provided clamps and screws are included with the

optional table top stand.

Figure 1

4. Installing and removing optional table

top stand

CAUTION: Installing and removing the stand must be done

by four or more people.

420 mm (X841UHD-2)

480 mm (X981UHD-2)

To install, follow those instructions included with the stand or

mounting apparatus. Use only those devices recommended

by the manufacturer.

Screw Holes

NOTE:

Use ONLY screws which are included with the

optional table top stand.

When installing the LCD monitor stand, handle the unit with

care to avoid pinching your ﬁngers.

Optional table top stand

Cord or chain

Clamp

Screw (M4)

Before attaching the LCD monitor to the wall, make sure that

the wall can support the weight of the monitor.

Be sure to remove the cord or chain from the wall before

moving the LCD.

Table

Protective Sheet

NOTE:

Install the stand in the direction of the arrow

which is imprinted on the surface of the stand.

Use the ST-801.

DO NOT use this monitor on the ﬂoor with the

table top stand. Please use this monitor on a table

or with a mounting accessory for support.

English-7

Parts Name and Functions

Control Panel

³ POWER button (

)

º EXIT button (EXIT)

Switches the power on/off. See also page 16.

Activates the OSD menu when the OSD menu is turned off.

Acts as EXIT button within the OSD to move to previous

menu.

· MUTE button (MUTE)

Switches the audio mute ON/OFF.

¾ Remote control sensor and Power Indicator

» INPUT button (INPUT)

Receives the signal from the remote control (when using the

wireless remote control). See also page 11.

Acts as SET/POINT ZOOM button within OSD menu.

(Toggle switches between [DVI1], [DVI2], [DPORT], [HDMI1],

[HDMI2], [HDMI3], [HDMI4], [OPTION]*). These are available

inputs only, shown as their factory preset name.

Glows green when the LCD monitor is in active mode*.

Glows red when the LCD is in POWER OFF mode.

Glows amber when the monitor is in Power Save Mode.

Green and Amber blink alternately while in Power Standby

mode with the “SCHEDULE SETTINGS” function enabled.

When a component failure is detected within the monitor, the

indicator will blink red.

¿ PLUS button (+)

Increases the audio output level when the OSD menu is

turned off.

* If “OFF” is selected in “POWER INDICATOR” (see page 27),

LED will not light when the LCD monitor is in active mode.

Acts as (+) button to increase the adjustment with OSD menu.

´ MINUS button (-)

Decreases the audio output level when the OSD menu is

turned off.

µ Room light sensing sensor

Detects the level of ambient light, allowing the monitor

to make automatic adjustments to the backlight setting,

resulting in a more comfortable viewing experience. Do not

cover this sensor. See page 31.

Acts as (-) button to decrease the adjustment with OSD menu.

² UP button (

)

Control Key Lock Mode

Activates the OSD menu when the OSD menu is turned off.

Acts as button to move the highlighted area up to select

adjustment items within OSD menu.

This control completely locks out access to all Control Key

functions. To activate the control key lock function, press

both and and hold down simultaneously for more than

3 seconds. To resume user mode, press both and and

hold simultaneously for more than 3 seconds.

¶ DOWN button (

Activates the OSD menu when the OSD menu is turned off.

Acts as button to move the highlighted area down to select

adjustment items within OSD menu.

)

*: This function depends on which option board you use.

English-8

Terminal Panel

(X981UHD-2) (X841UHD-2)

³ Main Power Switch

On/Off switch to turn main power ON/OFF.

¸ Internal speaker

¹ Internal/External speaker switch

: Internal speaker

NOTE: Please power off the monitor when you use the

Internal/External speaker switch.

: External speaker.

· AC IN connector

Connects with the supplied power cord.

» Service port

This USB slot is for future software upgrades.

Ƹ EXTERNAL SPEAKER TERMINAL

To output the audio signal from LINE IN, DisplayPort and

HDMI.

Red terminal is plus (+).

Black terminal is minus (-).

NOTE: This speaker terminal is for 15 W + 15 W (8 ohm)

speaker.

¿ LAN port (RJ-45)

LAN connection. See page 34 and 37.

NOTE: Please give priority for use to LAN1.

´ REMOTE IN

Use the optional wired remote control by connecting it to your

monitor.

NOTE: Do not use this connector unless speciﬁed.

ƹ LINE OUT

To output the audio signal from the LINE IN, DisplayPort and

HDMI to an external device (stereo receiver, ampliﬁer, etc.).

* This connector does not support Headphone terminal.

ᕦ RS-232C (D-Sub 9 pin)

Connect RS-232C input from external equipment such as a

computer in order to control RS-232C functions.

ƺ USB Downstream

To connect the monitor to USB devices.

¶ LINE IN

ƻ USB Upstream

To connect the monitor to external equipment such as a

To input audio signal from external equipment such as a

computer or player.

computer

º DVI IN (DVI-D) (Dual Link)

To input digital RGB signals from a computer or HDTV device

having a digital RGB output.

Ƽ Option board slot

Slot 2 type accessory is available. Please contact your

supplier for detailed information.

* This connector does not support analog input.

NOTE: Please contact your supplier for available option board.

¾ HDMI IN

To input digital HDMI signals.

ƽ Kensington Lock

For security and theft prevention.

µ DisplayPort IN

To input DisplayPort signals.

ƾ Intelligent wireless data sensor

Sensor for wireless communication of the monitor information

and settings.

ƿ Rating Label

English-9

Wireless Remote Control

º MENU button

Turns on/off the menu mode.

¾ ACTIVE PICTURE button

Selects active picture.

µ EXIT button

Returns to previous menu within OSD menu.

¸ UP/DOWN button (

)

Acts as button to move the highlighted area up or down

to select adjustment items within OSD menu.

Small screen which adjusted “PIP” mode moves up or down.

¹ MINUS/PLUS (-/+) button

Increases or decreases the adjustment level within OSD

menu settings.

Small screen which adjusted “PIP” mode moves left or right

and increases or decreases the size.

Ƹ SET/POINT ZOOM button

Makes selection. Activates POINT ZOOM function when OSD

menu is not shown.

ƹVOLUME UP/DOWN button (VOL +/-)

Increases or decreases audio output level.

ƺ CH/ZOOM UP/DOWN button (CH/ZOOM +/-)*¹

Increases or decreases POINT ZOOM level.

ƻ GUIDE button*¹

³ POWER button

Switches the power on/standby.

Ƽ MUTE button

Turns on/off mute function.

· INPUT button

ƽ PICTURE MODE button

Selects picture mode, [HIGHBRIGHT], [STANDARD],

[sRGB], [CINEMA], [CUSTOM1], [CUSTOM2],

[SVE-(1-5) SETTINGS]. See page 21.

Selects input signal.

HDMI1: HDMI1

HDMI2: HDMI2

HDMI3: HDMI3

HDMI4: HDMI4

DVI1: DVI1

HIGHBRIGHT: for moving images such as DVD.

STANDARD: for images.

DVI2: DVI2

sRGB: for text based images.

DisplayPort: DPORT

CINEMA: for movies.

CUSTOM1 and CUSTOM2: activates auto dimming

function. See page 31.

OPTION: OPTION*²

» MULTI INPUT button

SVE-(1-5) SETTINGS: for images and movies.

Selects input signal. See page 29.

PRESET1: PRESET1*³

ƾ ASPECT button

Selects picture aspect, [FULL], [WIDE], [DYNAMIC], [1:1],

[ZOOM] and [NORMAL]. See page 17.

PRESET2: PRESET2*³.

¿ OPTION MENU button*¹

ƿ AUDIO INPUT button

´ KEYPAD

Selects audio input source [LINE IN], [OPTION]*², [HDMI1],

[HDMI2], [HDMI3], [HDMI4], [DPORT].

Presses buttons to set and change passwords, change

channel and set REMOTE ID.

IMAGE FLIP button

² ENT button*¹

Toggle switches between [H FLIP], [V FLIP], [180° ROTATE]

and [NONE]. See page 24.

¶ DISPLAY button

Turns on/off the information OSD. See page 18.

English-10

MULTI PICTURE button

Operating Range for the Remote

Control

ON/OFF button: Toggle switches between ON and OFF.

See page 17.

MODE button: Selects picture number and a mode from PIP,

PBP 1, PBP 2, PBP 3.

Points the top of the remote control toward the LCD monitor’s

remote sensor during button operation.

CHANGE button: Selects a pair of pictures. You can swap

images between the selected two pictures.

PICTURE ASPECT button: Selects active picture frame

aspect.

Uses the remote control within a distance of about 7 m (23 ft.)

from remote control sensor or at a horizontal and vertical

angle of within 30° within a distance of about 3.5 m (10 ft.).

ROTATE button: Selects a multi picture to rotate 90°.

ALL ROTATE button: All multi pictures rotate 90°.

When MULTI PICTURE is OFF, the displayed single

picture rotates 90°.

NOTE: Enable to change each multi picture size by pressing

SET/POINT ZOOM button during multi picture mode.

You cannot select input other than the setting of the

HDMI/DVI SELECT.

STILL button*⁴

ON/OFF button: Activates/deactivates still picture mode.

STILL CAPTURE button: Captures still picture.

NOTE: This function is released when selecting MULTI

PICTURE MODE, TEXT TICKER, SCREEN SAVER, POINT

ZOOM, IMAGE FLIP except for NONE, SUPER in INPUT

CHANGE, INPUT CONFIGURATION.

Caution: Important, the remote control

system may not function

when direct sunlight or strong

illumination strikes the remote

control sensor or when there is

an object in the path.

When STILL is active, ROTATE is not available.

REMOTE ID button

Activates REMOTE ID function. See page 33.

MTS button*¹

button*¹

Handling the remote control

•

Do not subject to strong shock.

Do not allow water or other liquid to splash the remote

control. If the remote control gets wet, wipe it dry

immediately.

Activates closed captioning.

NOTE: VIDEO*², S-VIDEO*²inputs only.

•

Avoid exposure to heat and steam.

*1: This button’s action depends on which option board you use.

Refer to the option board’s manual for further information.

Other than to install the batteries, do not open the remote

control.

*2: This function depends on which option board you use.

*3: This function depends on INPUT CONFIGURATION setting.

*4: When you use OPTION signal input, this function depends on which option

board you use.

NOTE:

The buttons with no explanation do not function.

English-11

Setup

NEC recommends the following battery use:

1. Determine the installation location

CAUTION: Installing your LCD monitor must be done by a

qualiﬁed technician. Contact your dealer for more

information.

•

Place “AAA” size batteries matching the (+) and (-) signs

on each battery to the (+) and (-) signs of the battery

compartment.

•

Do not mix battery brands.

CAUTION: MOVING OR INSTALLING THE LCD MONITOR

MUST BE DONE BY FOUR OR MORE PEOPLE.

Failure to follow this caution may result in injury if

the LCD monitor falls.

Do not combine new and old batteries. This can shorten

battery life or cause liquid leakage of batteries.

•

Remove dead batteries immediately to prevent battery

acid from leaking into the battery compartment.

CAUTION: Do not mount or operate the monitor upside

down (X841UHD-2).

•

Do not touch exposed battery acid, it may injure skin.

NOTE:

If you do not intend to use the Remote Control for

a long period of time, remove the batteries.

Do not mount or operate the monitor upside

down or face down (X981UHD-2).

CAUTION: This LCD has a temperature sensor and cooling

fan, including a fan for the option board.

3. Connect external equipment

(See pages 14 and 15)

If the LCD becomes too hot, the cooling fan will

turn on automatically.

•

To protect the external equipment; turn off the main power

before making connections.

The option board’s fan is active although the

temperature is lower than normal operating

temperature for cooling the option board. If the

LCD becomes overheated while the cooling fan

is running, a “Caution” warning will appear. If the

“Caution” warning appears, discontinue use and

allow the unit to cool. Using the cooling fan will

reduce the likelihood of early circuit failure and

may help reduce image degradation and “Image

Persistance”.

If the LCD is used in an enclosed area or if the

LCD panel is covered with a protective screen,

please check the inside temperature of the

monitor by using the “HEAT STATUS” control

in the OSD (see page 28). If the temperature is

higher than the normal operating temperature,

please turn the cooling fan to ON within the FAN

CONTROL menu within the OSD (see page 28).

•

Refer to your equipment user manual for further

information.

NOTE:

Do not connect/disconnect cables when turning

on the monitor or other external equipment as this

may result in a loss of the monitor image.

4. Connect the supplied power cord

•

The equipment should be installed close to an easily

accessible power outlet.

Please fasten power cord to the LCD monitor by attaching

the screw and clamp.

Fully insert the prongs into the power outlet socket.

A loose connection may cause image degradation.

NOTE:

Please refer to the “Safety Precautions and

Maintenance” section of this manual for proper

selection of AC power cord.

IMPORTANT: Lay the protective sheet, which was wrapped

around the LCD monitor when it was

X841UHD-2:

packaged, beneath the LCD monitor so as not

to scratch the panel.

2. Install the remote control batteries

The remote control is powered by two 1.5V AAA batteries.

To install or replace batteries:

Screw

Clamp

A. Press and slide to open the cover.

X981UHD-2:

B. Align the batteries according to the (+) and (–) indications

inside the case.

C. Replace the cover.

CAUTION: Incorrect usage of batteries can result in leaks or

bursting.

Screw

Clamp

English-12

5. Switch on the power of all the attached

external equipment

When connected with a computer, switch on the power of the

computer ﬁrst.

6. Operate the attached external equipment

Display the signal from the desired input source.

7. Adjust the sound

Make volume adjustments when required.

8. Adjust the screen (See pages 23 and 24)

Make adjustments of the screen display position when

necessary.

9. Adjust the image (See page 23)

Make adjustments such as backlight or contrast when

required.

10. Recommended Adjustments

To reduce the risk of the “Image Persistence”, please adjust

the following items based on the application being used:

“SCREEN SAVER”, “SIDE BORDER COLOR” (See page 28)

“DATE & TIME” (See page 25), “SCHEDULE SETTINGS”

(See page 24).

It is recommended that the “FAN CONTROL” setting

(See page 28) be turned to ON also.

English-13

Connections

NOTE:

Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a

loss of the monitor image.

NOTE:

Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.

Before making connections:

First turn off the power of all the attached equipment and make connections.

Refer to the user manual included with each separate piece of equipment.

Wiring Diagram

USB Upstream

USB Downsstream

LINE OUT

Computer

Speaker L

Speaker R

Internal/EExternall speakerr switch

Player

Stereo Ampliﬁer

Solid lines = video signal

Dotted lines = audio signal

Computer

Connected

equipment

Connecting

terminal

DisplayPort

DVI1 (DVI-D1)

DVI2 (DVI-D2)

HDMI1

Setting in

TERMINAL SETTINGS

HDMI/DVI

Connecting audio

terminal

DPORT

LINE IN

HDMI1

Input button in

remote control

DisplayPort

DVI1

Input signal name

SELECT*²

DPORT

DVI1

DVI2

HDMI1

HDMI2

HDMI3

HDMI4

OPTION

DPORT

DVI1

DVI-HD

DVI*³, HDMI/DVI

HDMI, HDMI/DVI

DVI2

HDMI1

HDMI2

HDMI3

RAW/EXPAND*¹

HDMI2

HDMI3

HDMI4

Option

HDMI2

HDMI3

HDMI4

OPTION

DPORT

LINE IN

HDMI1

HDMI2

HDMI3

HDMI4

OPTION

HDMI4

OPTION

DisplayPort

DVI1

DVI2

HDMI1

HDMI2

HDMI3

HDMI4

OPTION

DisplayPort

DVI1 (DVI-D1)

DVI2 (DVI-D2)

HDMI1

DVI-HD/DVI-PC*¹

RAW/EXPAND*¹

DVI*³, HDMI/DVI

HDMI, HDMI/DVI

DVI2

HDMI1

HDMI2

HDMI3

HDMI4

OPTION

HDMI2

HDMI3

HDMI4

Option

*1: Depends on signal type.

*2: INPUT CONFIGURATION (See page 18).

*3: DVI signal is not displayed by factory setting. To display DVI signal, set to “HDMI/DVI” or “DVI” at HDMI/DVI SELECT.

English-14

Connecting a Personal Computer

Connecting your computer to your LCD monitor will enable you to display your computer’s screen image.

Some display cards may not display an image correctly.

Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically.

Scanning frequency

DisplayPort

Resolution

DVI

HDMI

Remarks

Horizontal

31.5 kHz

37.9 kHz

48.4 kHz

45.0 kHz

47.8 kHz

49.7 kHz

60.0 kHz

64 kHz

Vertical

60 Hz

30 Hz

60 Hz

24 Hz

1.2

1.1a

Yes

640 x 480

800 x 600

Yes

1024 x 768

1280 x 720

1280 x 768

1280 x 800

1280 x 960

1280 x 1024

1360 x 768

1366 x 768

1400 x 1050

1440 x 900

1600 x 1200

1680 x 1050

1920 x 1080

1920 x 1200

1920 x 2160

3840 x 2160

Yes

47.7 kHz

65.3 kHz

55.9 kHz

75.0 kHz

65.3 kHz

67.5 kHz

74.6 kHz

133.3 kHz

65.7 kHz

67.5 kHz

133.3 kHz

54.0 kHz

Yes

Yes*

Recommended resolution - DVI

Recommended resolution - HDMI

Recommended resolution - DisplayPort

Compressed image

Yes

4096 x 2160

Yes

*: Dual Link cable.

•

If you use with a Macintosh device, set “Mirroring” to Off on your device.

Refer to your Macintosh’s owner’s manual for more information about your computer’s video output requirements and any

special identiﬁcation or conﬁguration your monitor’s image and monitor may require.

•

Input TMDS signals conforming to DVI standards.

To maintain display quality, use a cable that conforms to DVI standards.

Connecting a Player or Computer with HDMI

•

Please use an HDMI cable with HDMI logo.

It may take a moment for the signal to appear.

Some display cards or drivers may not display an image correctly.

When you use a computer with HDMI, please set OVER SCAN to “AUTO” or “OFF” (see page 30).

Connecting a Computer with DisplayPort

•

Please use DisplayPort cable with DisplayPort compliance logo.

It may take a moment for the signal to appear.

Please note that when connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not

appear.

•

Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.

Connecting a USB device with USB port

Up Stream Port: Connect to a USB compatible computer with a USB cable.

Down Stream Port: Connect USB compatible ﬂash memory, mouse or key board to Down Stream Port.

•

Please make sure the connector shape and orientation when connecting the USB cable.

Depending on the use of computer BIOS, OS or device, USB function may not working. In this case, please check User’s

manual of your computer or device, or contact your supplier for detail information.

•

Before turning off the main power switch of monitor or shutting down Windows^®, please turn off USB function and remove the

USB cable from the monitor. You may lose data when computer got crush.

It may take few seconds the monitor recognizes USB input. Do not eject USB cable or eject and insert USB cable before

monitor recognizes the input.

English-15

Basic Operation

Power ON and OFF Modes

The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off.

NOTE:

The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the

Power Button.

Main Power Switch

OFF

Power Button

Using the remote control

English-16

Power Indicator

Aspect

DVI1, DVI2, DPORT, OPTION*⁴, PRESET1*⁵, PRESET2*⁵

Mode

Status Indicator Light

Green*¹

FULL

1:1

ZOOM

NORMAL

Power ON

Power OFF and Power Save “AUTO Red

STANDBY”

Power consumption under 0.5 W*²

Power Save “AUTO POWER SAVE” Amber

Power consumption under 0.5 W

HDMI1, HDMI2, HDMI3, HDMI4, PRESET1*⁵, PRESET2*⁵

FULL WIDE DYNAMIC 1:1 ZOOM NORMAL

Power Standby when “SCHEDULE

SETTINGS” enabled

Green and Amber blink alternately

*4: This function depends on which option board you use.

*5: This function depends on INPUT CONFIGURATION setting.

Diagnosis (Detecting failure)

Red Blinking

(See Troubleshooting page 49)

*1 If “OFF” is selected in POWER INDICATOR (page 27), the LED will not light when the

LCD monitor is in active mode.

*2 Without any option, with factory settings.

Aspect ratio

of image

Recommended selection

for picture aspect*³

NORMAL

Unchanged view*³

Initial settings

Setting LAN POWER (see page 28) and POWER SAVE (see

page 27) windows appear the ﬁrst time the power is on.

These settings are only necessary upon initial setup.

However, this message window appears when the power is

on after FACTORY RESET is done.

4:3

DYNAMIC

FULL

Using Power Management

Squeeze

Letterbox

The LCD monitor follows the VESA approved DPM Display

Power Management function.

WIDE

The power management function is an energy saving

function that automatically reduces the power consumption

of the display when the keyboard or the mouse has not been

used for a ﬁxed period.

*³Grey areas indicate unused portions of the screen.

The power management feature on your new display has

been set to the “AUTO STANDBY” mode. This allows your

display to enter a Power Saving Mode when no signal is

applied. This could potentially increase the life and decrease

the power consumption of the display.

NORMAL: Displays the aspect ratio the same as it is sent

from the source.

FULL: Fills entire screen.

WIDE: Expands a 16:9 letter box signal to ﬁll entire screen.

NOTE:

Depending on the computer and display card

used, this function may not operate.

DYNAMIC: Expands a 4:3 pictures to ﬁll the entire screen

with non-linearity. Some of the outside image area will be cut

off due to expansion.

NOTE:

The monitor automatically goes into OFF at the

preset time period after signal is lost.

1:1: Displays the image in a 1 by 1 pixel format.

ZOOM

MULTI PICTURE MODE

The image can be expanded beyond the active display area.

The image which is outside of active display area is not

shown.

Selects MULTI PICTURE MODE. You can select up to

4 pictures. When MULTI PICTURE is “ON” and PICTURE

NUMBER is 2 PICTURES, the display images are like below.

ZOOM

PIP

PBP1

PICTURES

When MULTI PICTURE is “ON” and PICTURE NUMBER is

3 PICTURES, the display images are like below.

ZOOM

PIP

PBP1

PBP2

PBP3

PICTURES

When MULTI PICTURE is “ON” and PICTURE NUMBER is

4 PICTURES, the display image is set to like below.

A: PICTURE 1

B: PICTURE 2

C: PICTURE 3

D: PICTURE 4

PICTURES

MULTI PICTURE MODE (See page 25).

English-17

INPUT CONFIGURATION

You can display 3840 x 2160 60 Hz image by using multiple input signals.

Selects input sources. Depending on the setting at HDMI/DVI SELECT, the selection of INPUT CONFIGURATION is changed.

HDMI/DVI SELECT

INPUT CONFIGURATION

OFF

HDMIx4 (PRESET1) HDMIx2 (PRESET1) HDMIx2 (PRESET2)

HDMI

OFF

HDMIx2 (PRESET1)

DVIx2 (PRESET1)

HDMI/DVI

DVI

INPUT CONFIGURATION (See page 29).

Information OSD

The Information OSD provides information such as: Input Source, Picture Size, etc.

Press the DISPLAY button on the remote to bring up the Information OSD.

Input Name

Audio input mode

Picture aspect

Input Signal Information

Multi picture information

Communication Info

English-18

Picture Mode

Depending on the setting at SPECTRAVIEW ENGINE (see page 31), selection of Picture mode is changed.

SPECTRAVIEW ENGINE is “ON”:

Selects ﬁve picture modes by Picture mode in OSD menu or using Picture mode button on the wireless remote control.

Selecting Picture mode with wireless remote control

By pressing Picture mode button, picture mode changes.

SVE-1

SVE-2

SVE-3

SVE-4

SVE-5

Selecting or changing Picture mode at Picture mode in OSD menu.

Selects a setting from SVE-1 to SVE-5. By pressing SET button again you can set below menus.

Choose the Picture Mode that is most suitable for the type of content that is shown.

There are several types of mode (sRGB, Adobe^®RGB SIM., eciRGB_v2 SIM., DCI SIM., REC-Bt709, HIGH BRIGHT, FULL,

DICOM SIM, PROGRAMMABLE).

•

Each PICTURE MODE includes LUMINANCE, WHITE, GAMMA, BLACK, RED, GREEN, BLUE, COLOR VISION EMU,

UNIFORMITY and METAMERISM settings.

The type of PRESET

PRESET

sRGB

PURPOSE

Standard color space used for the Internet, Windows operating systems and digital cameras. Recommended setting

for general color management.

Adobe^®RGB SIM.

Provides a standard color space used in high-end graphics applications such as professional digital still cameras and

imaging.

eciRGB_v2 SIM.

DCI SIM.

Provides a color space proﬁle recommended by ECI (The European Color Initiative).

Color setting for digital cinema.

REC-Bt709

Color setting for High-deﬁnition television.

HIGH BRIGHT

FULL

Highest brightness setting.

Native display color gamut. Suitable for use with color managed applications.

Setting that conforms to the DICOM standard for the Grayscale Standard Display Function.

DICOM SIM.

PROGRAMMABLE

For “MultiProﬁler” software or the Hardware Calibration settings by NEC Display Solutions software (some OSD

settings are disabled).

MODE

PURPOSE

LUMINANCE

Adjusts the overall image and screen background brightness.

Press “LEFT” or “RIGHT” to adjust.

WHITE

Adjusts the white color by temperature or xy setting. A lower color temperature will make the screen reddish and a

higher color temperature will make the screen bluish. A stronger x makes the screen reddish, a stronger y makes it

greenish and weak xy makes it a bluish white.

English-19

GAMMA

Allows you to manually select the brightness level of grayscale. There are ﬁve selections: sRGB, L STAR,

DICOM SIM. and CST. We recommend to show grayscale image data on screen.

sRGB: GAMMA setting for sRGB.

L STAR: GAMMA setting for Lab color space.

DICOM SIM.: DICOM GSDF (Grayscale Standard Display Function) is typically used for medical imaging.

CST: CUSTOM VALUE can be adjusted when CST is selected as the GAMMA SELECTION setting.

CUSTOM VALUE: The gamma value is selected from the rate of 0.5 to 4.0 by 0.1 steps.

BLACK

Adjusts the black luminance.

Adjusts color gamut.

RED

GREEN

BLUE

COLOR VISION EMU Previews various typical human vision deﬁciencies and is useful for evaluating how people who have such

deﬁciencies will perceive colors. This preview is available in four modes: Types P (Protanopia), D (Deuteranopia) and

T (Tritanopia) emulate color vision dichromacy, and Grayscale can be used for evaluating contrast legibility.

NOTE: Depending on the vision of the user, including those with color vision deﬁciency, there will be a variation in

how the screen's color is seen and experienced.

A simulation is used to illustrate the view of those with a color vision deﬁciency. It is not their actual view. The

simulation is a reproduction of those with a strong color vision mode of type P, type D or type T. People with a slight

color vision deﬁciency will experience little to no difference compared to those with normal color vision.

UNIFORMITY

METAMERISM

This function electronically compensates for the slight variations in the white uniformity level as well as for deviations

in color that may occur throughout the display area of the screen. These variations are characteristic of LCD panel

technology. This function improves the color and evens out the luminance uniformity of the display.

NOTE: A higher number produces a better effect, but may also reduce CONTRAST RATIO.

Compensates the visual color difference with the other displays.

If you prefer to get closer display color to the picture mode setting, set to OFF.

NOTE:

- When the selected PICTURE MODE is different from your computer’s ICC color proﬁle, you may experience

inaccurate color reproduction.

- MultiProﬁler software, developed by NEC Display Solutions, is highly recommended to provide extended color

management features such as ICC proﬁle Emulation and Printer Emulation. The latest MultiProﬁler software is

available on the NEC Display Solutions website.

English-20

SPECTRAVIEW ENGINE is “OFF”:

Selects ﬁve picture modes by Picture mode in OSD menu or using Picture mode button on the wireless remote control.

DVI1, DVI2, DPORT, OPTION*, PRESET1*¹, PRESET2*¹

STANDARD

sRGB

CUSTOM1

CUSTOM2

HIGHBRIGHT

HDMI1, HDMI2, HDMI3, HDMI4, PRESET1*¹, PRESET2*¹

STANDARD CINEMA CUSTOM1 CUSTOM2

HIGHBRIGHT

The type of PRESET

PRESET

HIGH BRIGHT

STANDARD

sRGB

PURPOSE

Highest brightness setting.

Standard setting.

Standard color space used for the Internet, Windows operating systems and digital cameras. Recommended setting

for general color management.

CINEMA

CUSTOM

Setting that boosts dark tones; best suited for movies.

Activates auto dimming function.

*: This function depends on which option board you use.

*¹: This function depends on INPUT CONFIGURATION setting.

English-21

OSD (On-Screen-Display) Controls

NOTE:

Some functions may not be available depending on the model or optional equipment.

Input source

Main Menu Icons

Main Menu Item

Adjustment Settings

Sub Menu

THANK YOU FOR SAVING

PICTURE MODE

THE ENVIRONMENT.

CARBON FOOTPRINT

86.0 %

Goto Adjustment Return

Select

Key Guide

Press UP or DOWN

button to select

sub-menu.

Press SET/POINT

ZOOM.

Press UP or DOWN,

PLUS or MINUS to select

the function or setting to

be adjusted.

Press MENU or EXIT.

Remote Control

Press UP or DOWN

button to select.

Press INPUT button

to decide.

Press UP or DOWN, PLUS

or MINUS button to select.

Press EXIT

Control Panel

OSD screen

English-22

Setting

Default

PICTURE

BACKLIGHT*¹

Adjusts the overall image and background brightness. Press + or - to adjust.

NOTE: When MODE1 or MODE2 is selected in ROOM LIGHT SENSING, this function cannot be

changed.

Depends on

destination

CONTRAST*¹

Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.

NOTE: When sRGB is selected in picture mode, this function cannot be changed.

SHARPNESS*¹

BRIGHTNESS*¹

Adjusts the crispness of the image. Press + or - to adjust.

50*²

Adjusts the image brightness in relationship to the background. Press + or - to adjust.

NOTE: When sRGB is selected in picture mode, this function cannot be changed.

COLOR TEMPERATURE*¹Adjusts the color temperature of the entire screen. A low color temperature will make the screen

reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further

adjustment, the individual R/G/B/ levels of the white point can be adjusted. To adjust the R/G/B

levels, CUSTOM must be showing as the COLOR TEMP selection.

10000K

NOTE: When sRGB is selected in picture mode, predeﬁned 6500k is set so it cannot be changed.

When PROGRAMMABLE1, PROGRAMMABLE2 or PROGRAMMABLE3 is selected in GAMMA

CORRECTION, this function cannot be changed.

COLOR CONTROL*¹

Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.

NOTE: When sRGB is selected in picture mode, this function cannot be changed.

GAMMA CORRECTION*¹

Select a display gamma for best picture quality.

NOTE: When sRGB is selected in picture mode, this function cannot be changed.

NATIVE*²

(except sRGB

setting)

NATIVE

2.2

Gamma correction is handled by the LCD panel.

Typical display gamma for use with a computer.

Good for video (DVD, etc.)

2.4

S GAMMA

Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the

image (S-Curve).

DICOM SIM.

DICOM GSDF curve simulated for LCD type.

PROGRAMMABLE1, 2, 3 A programmable gamma curve can be loaded using NEC optional software.

UHD UPSCALING*¹

PICTURE MODE

Achieves high-deﬁnition effect.

OFF

Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [CUSTOM1],

[CUSTOM2], [SVE-1 SETTINGS], [SVE-2 SETTINGS], [SVE-3 SETTINGS], [SVE-4 SETTINGS]

or [SVE-5 SETTINGS]. See page 19.

Depends on

destination

RESET

Resets the following settings within the PICTURE menu back to factory setting: BACKLIGHT,

CONTRAST, SHARPNESS, BRIGHTNESS, COLOR TEMPERATURE, COLOR CONTROL,

GAMMA CORRECTION, UHD UPSCALING.

ADJUST

ASPECT

Select the aspect ratio of the screen image.

FULL

NOTE: When the ASPECT is DYNAMIC or ZOOM, the image will be changed to FULL image

before POINT ZOOM, IMAGE FLIP, SCREEN SAVER, then start to POINT ZOOM, IMAGE FLIP,

SCREEN SAVER. After POINT ZOOM, IMAGE FLIP, SCREEN SAVER, ASPECT will be returned

to previous ASPECT. When ASPECT is changed during POINT ZOOM, IMAGE FLIP, SCREEN

SAVER, DYNAMIC and ZOOM will be FULL image.

When INPUT CONFIGURATION is active, ZOOM is not available. ZOOM is not available with

3840 x 2160 60 Hz signal.

NORMAL

FULL

Displays the aspect ratio the same as it is sent from the source.

Fills entire screen.

WIDE

Expands a 16:9 letter box signal to ﬁll entire screen.

DYNAMIC

Expands a 4:3 pictures to ﬁll the entire screen with non-linearity. Some of the outside image area

will be cut off due to expansion.

1:1

Displays the image in a 1 by 1 pixel format. (If the input resolution is higher than a 3840 x 2160

resolution, the image will be scaled down to ﬁt the screen).

If ROTATE of MULTI PICTURE CONTROL is selected, characters and lines may be displayed in

blurring, depending on the signal resolution.

*1: If SPECTRAVIEW ENGINE is ON, this function is grayed out.

*2: Depends on signal input.

English-23

ZOOM

The image can be expanded/reduced.

NOTE: The expanded image which is outside of active display area is not shown. The reduced

image may have some image degradation.

ZOOM

Maintains the aspect ratio while zooming.

Amount of horizontal zoom.

Amount of vertical zoom.

Horizontal position.

HZOOM

VZOOM

H POS

V POS

Vertical position.

IMAGE FLIP

NOTE: When the ASPECT is DYNAMIC, the image will be changed to FULL image before

IMAGE FLIP, then start to IMAGE FLIP. This function is not available when MOTION in SCREEN

SAVER or ROTATE is “ON”.

When selecting IMAGE FLIP except for NONE, following functions are released:

MULTI PICTURE MODE, TEXT TICKER, STILL, POINT ZOOM and ROTATE.

When input signal is Interlace, the image may be disturbed.

IMAGE FLIP

Display the inverse image right-left, up-down or rotation.

Press + or - to select.

NONE

H FLIP

V FLIP

Normal mode.

The image inverts right-left.

The image inverts up-down.

The image rotates 180 degrees.

180° ROTATE

OSD FLIP

Determines the OSD display direction.

OFF

If “ON” is selected, OSD will invert depending on the image.

RESET

Resets “ADJUST” settings back to factory settings.

Increases or decreases output volume level.

AUDIO

VOLUME

BALANCE

Select “STEREO” or “MONO” of audio output.

CENTER,

STEREO

If you select “STEREO”, adjust the balance of L/R volume.

Press + button to move the stereo sound image to right.

Press - button to move the stereo sound image to left.

TREBLE

BASS

To accentuate or reduce the high frequency sound.

Press + button to increase TREBLE sound.

Press - button to decrease TREBLE sound.

To accentuate or reduce the low frequency sound.

Press + button to increase BASS sound.

Press - button to decrease BASS sound.

SURROUND

Artiﬁcial surround sound.

NOTE: LINE OUT is disabled when this function is set to “ON”.

OFF

PICTURE 1

FIXED

MULTI PICTURE AUDIO

Selects source of MULTI PICTURE AUDIO.

NOTE: This function depends on MULTI PICTURE setting.

LINE OUT

Selecting “VARIABLE” enables control of the line out level with the VOLUME button.

Selects audio input source LINE IN, DPORT, HDMI1, HDMI2, HDMI3, HDMI4, OPTION*¹.

AUDIO INPUT

Depends on

signal input

AUDIO DELAY

RESET

Enables to set the delay time to output the audio. DELAY TIME can be set between 0 and

100 milliseconds. “ON” activates this function.

ON,

37 MSEC.

Resets “AUDIO” options back to factory settings except VOLUME.

SCHEDULE

OFF TIMER

Sets the monitor to power off after a length of time.

A time between 1 to 24 hours is available.

OFF/1 HOUR

SCHEDULE SETTINGS

SCHEDULE LIST

Creates a working schedule for the monitor to use.

NOTE: If your schedule is across date, please set ON time and OFF time individually at Settings.

List of schedules.

*1: This function depends on which option board you use.

English-24

DATE & TIME

Sets the date, time, and daylight saving region. Date & time must be set in order for the

“SCHEDULE” function to operate. See page 32.

YEAR

MONTH

Conﬁgures the year for the real-time clock.

Conﬁgures the month for the real-time clock.

Conﬁgures the day for the real-time clock.

Conﬁgures the time for the real-time clock.

Conﬁgures daylight savings on or off.

DAY

TIME

OFF

DAYLIGHT SAVING

RESET

Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER,

SCHEDULE SETTINGS.

MULTI PICTURE CONTROL*¹

KEEP MULTI PICTURE

MODE

Allows the monitor to remain in MULTI PICTURE and TEXT TICKER mode after powering off.

When Power is returned, MULTI PICTURE and TEXT TICKER appear without having to enter

the OSD.

OFF

MULTI PICTURE MODE*³Selects picture number and display form.

NOTE: This function is released when selecting SUPER in INPUT CHANGE, SCREEN SAVER,

INPUT CONFIGURATION, IMAGE FLIP except for NONE.

When this function is “ON”, STILL, POINT ZOOM are not available.

MULTI PICTURE

When “OFF” is selected one picture is displayed.

When “ON” is selected several pictures are displayed.

PICTURE NUMBER

Selects [2 PICTURES], [3 PICTURES], [4 PICTURES].

After selected PICTURE NUMBER, select display form PIP, PBP1, PBP2, or PBP3. Depending

on the setting at PICTURE NUMBER, display form selection is changed. See page 17.

2 PICTURES/

PIP

ACTIVE PICTURE*²

ACTIVE

When MULTI PICTURE is “OFF”, [PICTURE 1] is Active Picture. When MULTI PICTURE is “ON”,

sets Active Picture.

PICTURE1

NOTE: This function depends on MULTI PICTURE setting.

ACTIVE FRAME

INPUT SELECT*³

ON: Active picture is shown with frame.

Selects Multi Picture input. Press the + button or - button to select input.

NOTE: This function is not available when MULTI PICTURE is “OFF”.

Press SET button after selecting Active Picture input.

PICTURE SIZE*²

Sets Active Picture size.

Press the SET/POINT ZOOM button to adjust picture size. Press + or CH+ to expand. Press - or

CH- to reduce.

NOTE: This function is not available when MULTI PICTURE is 4 PICTURES PBP.

Depends on the setting at MULTI PICTURE MODE, some picture cannot change it’s size.

PICTURE POSITION*²

PICTURE ASPECT*²

Sets Active Picture location.

Pressing the + button moves Active Picture to the right, and pressing the - button moves it to

the left.

X=95, Y=92

Pressing the

button moves Active Picture up, and pressing the

button moves it down.

NOTE: This function is not available when MULTI PICTURE is 4 PICTURES PBP.

Selects Active Picture frame aspect, [FULL], [NORMAL] and [EXPAND].

To change aspect ratio of the screen image, see page 17.

NOTE: This function depends on MULTI PICTURE setting.

NORMAL

OFF

ROTATE*³

ROTATE ALL

PICTURE1

PICTURE2

PICTURE3

PICTURE4

When “ON” is selected, all pictures rotate.

When “OFF” is selected, sets each picture ROTATE settings.

NOTE: When TEXT TICKER, IMAGE FLIP except for NONE, STILL is ON or SCREEN SAVER

is active, this function is not available. If ASPECT “1:1” is selected, characters and lines may be

displayed in blurring, depending on the signal resolution.

When ROTATE is ON, POINT ZOOM and IMAGE FLIP except for NONE are not available.

Each picture ROTATE settings are released when MULTI PICTURE is set to “OFF”.

When input signal is Interlace, the image may be disturbed.

If input signal is 3840 x 2160 60 Hz and [3 PICTURES], [4 PICTURES] is selected at PICTURE

NUMBER in MULTI PICTURE MODE, ROTATE is not available.

If ROTATE of MULTI PICTURE CONTROL is selected in the input signal with a high refresh rate,

the image may not be displayed smoothly. To reduce this condition, please set the input signal

with a low refresh rate.

*1: This function is released when selecting SUPER in INPUT CHANGE, SCREEN SAVER, INPUT CONFIGURATION, IMAGE FLIP except for NONE.

*2: When TEXT TICKER is active, this function is not available.

*3: When you select OPTION for multi picture input, this function depends on which option board you use.

English-25

TEXT TICKER*¹

MODE

OFF

Enables Text Ticker and allows you to set Horizontal or Vertical direction.

Selects the location of the Text Ticker on the screen.

Determines the size of the Text Ticker in relationship to the overall screen size.

Enables auto-detection of the Text Ticker.

POSITION

SIZE

DETECT

PICTURE1

PICTURE2

Selects input signals.

NOTE: When this function is active, POINT ZOOM, STILL and ROTATE are not available.

RESET

Resets MULTI PICTURE CONTROL options back to factory settings except for INPUT SELECT

and PICTURE ASPECT.

OSD

LANGUAGE

ENGLISH

DEUTSCH

FRANÇAIS

ITALIANO

ESPAÑOL

SVENSKA

РУССКИЙ

Select the language used by the OSD.

ENGLISH

(Depends on

destination)

MENU DISPLAY TIME

OSD POSITION

Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.

Determines the location where the OSD appears on the screen.

30 SEC.

X = 128, Y = 225

DOWN

RIGHT

LEFT

INFORMATION OSD

Selects whether the information OSD is displayed or not. The information OSD will be displayed

when the input signal or source changes. The information OSD will also give a warning when

there is no-signal or the signal is out-of range.

ON, 3 SEC.

An interval between 3 to 10 seconds for the Information OSD to appear is available.

COMMUNICATION

INFO

MONITOR ID and IP ADDRESS will be displayed when the remote control Display button is

pressed.

MONITOR INFORMATION Indicates the model and serial number of your monitor and ﬁrmware version.

CARBON SAVINGS: Display the estimated carbon saving information in kg-CO2. The carbon

footprint factor in the carbon saving calculation is based on the OECD (2008 Edition).

CARBON USAGE: Display the estimated carbon usage information in kg-CO2. This is the

arithmetic estimation, not actual measurement value. This estimation is based without any

options.

OSD TRANSPARENCY

OSD ROTATION

LANDSCAPE

Set the transparency of the OSD.

OFF

Determines the OSD display direction between landscape and portrait.

Display the OSD with landscape mode.

LANDSCAPE

PORTRAIT

Display the OSD with portrait mode.

INPUT NAME

You can create a name for the INPUT currently being used.

Max: 8 characters, including Space, A-Z, 0-9, and some symbols.

MEMO

RESET

Sets a title and message via HTTP server. See page 45.

Resets the following settings within the OSD menu back to factory setting:

MENU DISPLAY TIME, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY.

*1: When you select OPTION for multi picture input, this function depends on which option board you use.

English-26

MULTI DISPLAY

ID CONTROL

Sets the monitor ID number from 1-100 and group ID from A-J. DETECTED MONITORS shows

the number of all monitors which follow in the chain with LAN.

NOTE: Group ID is made of multiple selections.

AUTO ID

When “YES” is selected, monitor ID numbers are set automatically in all monitors which follow in

the chain with LAN.

NOTE: All monitors which follow in the chain with LAN should be ON. When executing this

function while in standby mode or power save mode, “LAN POWER” should be ON.

AUTO ID RESET

Resets monitor ID number of all monitors which follow in the chain with LAN.

NOTE: AUTO ID RESET should be done when changes the number of monitors which follow in

the chain with LAN.

IR LOCK SETTINGS

Prevents the monitor from being controlled by the wireless remote control.

When ACTIVATE is selected, all the settings are activated.

UNLOCK

NOTE: IR LOCK SETTINGS is a function intended only to the wireless remote control buttons.

This function does not lock out access to all buttons at the back of the monitor. To return to

normal operation, press the “DISPLAY” button on the remote control for 5 seconds.

MODE SELECT

UNLOCK

Selects the mode UNLOCK, ALL LOCK or CUSTOM LOCK.

All buttons on the remote control are available for normal operations.

Locks all remote control buttons.

ALL LOCK

CUSTOM LOCK

Selects which buttons to be locked from POWER, VOLUME, and INPUT button.

Except for CUSTOM LOCK settings, other buttons on the remote control are locked.

POWER: When LOCK is selected, POWER button is locked.

VOLUME: When UNLOCK is selected, sets minimum and maximum volume between VOL.0 to

VOL.100.

VOLUME (+) button and VOLUME (-) button are only available from the minimum

volume to the maximum volume you set.

When LOCK is selected, VOLUME (+) button and VOLUME (-) button are locked.

INPUT:

When UNLOCK is selected, choose up to three buttons from DVI1, DVI2, DPORT,

HDMI1, HDMI2, HDMI3, HDMI4, OPTION*¹, PRESET1*², PRESET2*², which you

prefer to be unlocked.

The unselected buttons are locked. When LOCK is selected, all INPUT buttons are

locked.

POWER ON DELAY

DELAY TIME

Adjusts the delay time between being in “standby” mode and entering “power on” mode.

“POWER ON DELAY” can be set between 0 and 50 seconds.

0 SEC.

OFF

LINK TO ID

When “ON” selected, delay time is linked with Monitor ID. It takes more time as larger ID number.

POWER INDICATOR

Turns ON or OFF the LED located at the front of the monitor.

If “OFF” is selected, LED will not light when the LCD monitor is in active mode.

SETTING COPY

In a daisy chain scenario, select the OSD menu categories that you want to copy over to the

other monitor.

NOTE: When you use this function, monitors should be daisy chained by LAN. This function

resets to default when power is off. This function has a limit depending on the cable you use.

COPY START

ALL INPUT

RESET

Select “YES” and press the SET button to start copying.

All input terminals settings are copied when you select this item. Default is off.

Resets “MULTI DISPLAY” options back to factory settings except for POWER ON DELAY.

DISPLAY PROTECTION

POWER SAVE

Sets how long the monitor waits to go into power save mode after the signal is lost.

AUTO

NOTE: When connecting DVI, the display card might not stop sending the digital data even

though the image might have disappeared. If this occurs the monitor will not switch into power

management mode. POWER SAVE is disabled when AUTO OFF or CUSTOM is selected in

HUMAN SENSING*³.

STANDBY

AUTO POWER SAVE

AUTO STANDBY

DISABLE

The monitor automatically goes into OFF at the preset time period after signal is lost.

The monitor will return to normal mode when signal is restarted.

180

The monitor automatically goes into OFF at the preset time period after signal is lost.

Press the power button to return to normal mode.

The monitor will not goes into OFF after signal is lost.

*1: This function depends on which option board you use.

*2: This function depends on INPUT CONFIGURATION setting.

*3: The function is available only when connecting the optional control unit.

English-27

HEAT STATUS

FAN CONTROL

Displays status of the FAN, BACKLIGHT and TEMPERATURE.

Cooling fan reduces the temperature of the display to protect from overheating.

AUTO, HIGH

If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.

SCREEN SAVER

Use the SCREEN SAVER function to reduce the risk of Image Persistence.

NOTE: This function is released when INPUT CONFIGURATION is active. When SCREEN

SAVER is ON, the image will be changed FULL image. After released SCREEN SAVER, the

image will be displayed with current ASPECT setting.

3840 x 2160 (60 Hz) input cannot be selected.

When SCREEN SAVER is active, MULTI PICTURE, ROTATE, STILL, IMAGE FLIP except for

NONE or TEXT TICKER, POINT ZOOM are not available.

GAMMA*

The display gamma is changed and ﬁxed when “ON” is selected.

OFF

BACKLIGHT*

The brightness of backlight is decreased when “ON” is selected.

NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.

MOTION*¹

The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at

user determined intervals. You can set interval time and zooming ratio.

OFF

SIDE BORDER COLOR

Adjusts the color of the side borders when a 4:3 image is displayed.

Press + button, the bar will become lighter.

Press - button, the bar will become darker.

CHANGE PASSWORD

SECURITY

Allows the security password to be changed.

The factory preset password is 0000.

Locks the security password.

OFF

START-UP LOCK: Security password is required when the monitor power is on.

CONTROL LOCK: Security password is required when the remote control button or control button

on the monitor is pressed.

BOTH LOCK: Security password is required when the monitor power is on, or the remote control

button or control button on the monitor is pressed.

RESET

Resets the following settings within the DISPLAY PROTECTION menu back to factory setting:

POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR.

EXTERNAL CONTROL

NETWORK

Displays current network settings.

INFORMATION

IP ADDRESS SETTINGS

NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN

SETTING is applied.

IP SETTING

Enabling this option automatically assigns an IP address to the monitor from your DHCP server.

Disabling this option allows you to register the IP address or subnet mask number obtained from

your network administrator.

AUTO

NOTE: Consult your network administrator for the IP address when “AUTO” is selected for

[IP SETTING].

IP ADDRESS

Set your IP address of the network connected to the monitor when “MANUAL” is selected for

[IP SETTING].

192.168.0.10

255.255.255.0

0.0.0.0

SUBNET MASK

DEFAULT GATEWAY

Set your subnet mask number of the network connected to the monitor when “MANUAL” is

selected for [IP SETTING].

Set your default gateway of the network connected to the monitor when “MANUAL” is selected

for [IP SETTING].

NOTE: Set as [0.0.0.0] to delete the setting.

DNS

Set for IP ADDRESS SETTINGS of DNS server.

AUTO

AUTO: Automatically assign an IP address of DNS server connected to the monitor.

MANUAL: Set your IP address of DNS server connected to the monitor.

DNS PRIMARY

DNS SECONDARY

LAN POWER

Set your primary DNS settings of the network connected to the monitor.

NOTE: Set as [0.0.0.0] to delete the setting.

0.0.0.0

OFF

Set your secondary DNS settings of the network connected to the monitor.

NOTE: Set as [0.0.0.0] to delete the setting.

Selects LAN operation mode. When “ON” selected, allows to supply power to LAN during power

save mode or standby mode.

NOTE: For enabling “AUTO ID”, this function should be ON.

DDC/CI

PING

ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor.

Conﬁrm the response by communicating to the preset IP address.

ENABLE

192.168.0.10

IP ADDRESS RESET

RESET

Resets IP ADDRESS SETTINGS back to factory settings.

Resets the following setting within the EXTERNAL CONTROL menu back to factory settings:

DDC/CI.

*: If SPECTRAVIEW ENGINE is ON, this function is grayed out.

*1: When you select OPTION for signal input, this function depends on which option board you use.

English-28

ADVANCED OPTION1

INPUT DETECT

Selects the method of input detection the monitor uses when more than two input devices are

connected.

NONE

NOTE: When SUPER is selected in INPUT CHANGE, this function cannot be changed.

NONE

The Monitor will not search the other video input ports.

FIRST DETECT*¹

When the current video input signal is not present, then the monitor searches for a video signal

from the other video input port. If the video signal is present in the other port, then the monitor

switches the video source input port to the new found video source automatically.

The monitor will not look for other video signals while the current video source is present.

LAST DETECT*¹

When the monitor is displaying a signal from the current source and a new secondary source

is supplied to the monitor, the monitor will automatically switch to the new video source. When

current video input signal is not present, the monitor searches for a video signal from the other

video input port. If the video signal is present in the other port, then the monitor switches the

video source input port to the new found video source automatically.

CUSTOM DETECT*¹

LONG CABLE COMP

Set the priority of input signals.

When CUSTOM DETECT is selected, monitor searches listed inputs only.

NOTE: Priority of option input signal is only available in PRIORITY3 except for slot 2 type PC

option.

Compensates for image degradation caused by using a long cable.

A lower number produces less compensation.

MODE1

If displayed image has noise, selects MODE2 or MODE3.

If you are using a long cable equipped with Equalizer, selects MODE0 or MODE1.

NOTE: LONG CABLE COMP does not compensate signal with DisplayPort cable.

INPUT CHANGE*¹

Sets input change speed. When selected “SUPER”, allows to switch high-speed between set two

signals.

NORMAL

NOTE: When “QUICK” is selected, picture may be distorted when signal input is changed.

When INPUT CONFIGURATION is ACTIVE, “SUPER” is not available.

When “SUPER” is active, MULTI PICTURE MODE, TEXT TICKER, STILL, POINT ZOOM are not

available.

This function should be chosen after all adjustment options have been made for the input.

TERMINAL SETTINGS

HDMI/DVI SELECT

Selects input terminal sources [HDMI], [DVI] or [HDMI/DVI].

NOTE: Selected input only displays.

DVI signal is not displayed by factory setting. To display DVI signal, set to “HDMI/DVI” or “DVI”.

HDMI

OFF

INPUT

CONFIGURATION

Selects input sources. See page 18.

When this function is “ON”, MULTI PICTURE MODE, TEXT TICKER, SCREEN SAVER, STILL,

POINT ZOOM, SUPER in INPUT CHANGE, ZOOM in ASPECT are not available.

HDMI

Selects “ON” or “OFF” the multi input sources [HDMI x 4 (PRESET1)], [HDMI x 2 (PRESET1)],

[HDMI x 2 (PRESET2)]

HDMI x 4 (PRESET1): When [HDMI x 2 (PRESET1)] or [HDMI x 2 (PRESET2)] is set,

[HDMI x 4 (PRESET1)] is disable.

HDMI x 2 (PRESET1): When “TOP & BOTTOM” is set, [HDMI x 2 (PRESET2)] is disable.

HDMI x 2 (PRESET2): When “TOP & BOTTOM” is set, [HDMI x 2 (PRESET1)] is disable.

DVI

Selects “LEFT & RIGHT” or “TOP & BOTTOM” the multi input sources [DVI x 2 (PRESET1)].

Selects “LEFT & RIGHT” the multi input sources [HDMI x 2 (PRESET1)].

OFF

HDMI/DVI

DVI MODE

Selects the kind of DVI-D equipment which is connected to the DVI input.

DVI-HD

Select “DVI-HD” when DVD player or computer equipment, which requires HDCP authentication,

is connected.

Select “DVI-PC” when a computer equipment, which not requires HDCP authentication, is

connected.

DisplayPort

BIT RATE

Selects DisplayPort mode [1.1a] or [1.2]. (If the input resolution is higher than a 3840 x 2160

resolution, the image will be scaled down to ﬁt the screen).

1.2

If DisplayPort 1.1a is selected, you can set [RBR] or [HBR].

If DisplayPort 1.2 is selected, you can set [RBR], [HBR] or [HBR2].

NOTE: This function depends on DisplayPort setting.

HBR

HBR2

HDMI SIGNAL

RAW: For computer setting. Displays all input signals of 0-255 steps.

EXPAND: For audio-visual equipment setting. Expands input signals of 16-235 steps to

0-255 steps.

EXPAND

*1: When you select OPTION for signal input, this function depends on which option board you use.

English-29

DEINTERLACE

Selects the IP (Interlace to Progressive) conversion function.

NOTE: For DVI input “DVI-HD” needs to be enabled in the DVI mode menu.

Converts interlaced signals to progressive. This is the default setting.

OFF

Disables IP conversion. This setting is best suited for motion pictures, but increases the risk of

image retention.

MOVIE SETTINGS

Selects suitable settings for Movie.

TELECINE

Automatically senses the sources frame rate for optimal picture quality.

AUTO*³

OFF

HDMI1, HDMI2, HDMI3, HDMI4, PRESET1*²,

PRESET2*²inputs only.

ADAPTIVE

Sets the level of adjustment for dynamic contrast.

CONTRAST*¹

HDMI1, HDMI2, HDMI3, HDMI4, PRESET1*²,

PRESET2*²inputs only.

OVER SCAN

Some video formats may require different scanning modes in order to best display the image.

AUTO

HDMI1, HDMI2, HDMI3, HDMI4, PRESET1*²,

PRESET2*²inputs only.

Image size is larger than what can be displayed. The image edge will appear cropped.

Approximately 95% of the image will be shown on the screen.

OFF

Image size stays within the display area. The whole image is displayed on the screen.

NOTE: When you use a computer with HDMI out, please set “OFF”.

AUTO*⁵

Sets scanning modes automatically.

OPTION SETTINGS

OPTION POWER

Allow the monitor to supply power to Option board slot during power save mode or standby

OFF

mode.

NOTE: This function should be set to ON when using power save management by slot 2 type

option.

AUDIO*⁴

Selects sound input signal according to slot2 type option’s speciﬁcations. To activate DIGITAL,

select OPTION for input signal and OPTION for AUDIO INPUT.

NOTE: DIGITAL is activated only when OPTION is selected for input signal and OPTION for

AUDIO INPUT.

ANALOG

INTERNAL PC*⁴

OFF WARNING

The function is available for slot 2 type PC.

If OPTION POWER is OFF, a warning message appears when monitor power is turned off.

NOTE: Warning message does not appear when monitor power is turned off by OFF TIMER

setting or SCHEDULE setting.

OFF

AUTO OFF

Monitor power is automatically “OFF” when connected PC is OFF or the monitor is in power save

mode.

NOTE: If you select “OFF”, monitor power is not automatically “ON” when connected PC is ON.

START UP PC

FORCE QUIT

When ON is selected, connected PC start-up.

When ON is selected, it performs force-quit PC.

Please use this function only when the operating system cannot be shut down manually.

SLOT2 CH SETTING*⁴Selects signal type according to slot 2 type option’s speciﬁcations.

AUTO

1CH

Sets signal type automatically.

Fill entire the signal which is selected in SLOT2 CH SELECT.

2CH

DisplayPort signal is displayed in the left half, TMDS signal is displayed in the right half. If you do

not have either of the input signal, the signal having the input is automatically displayed on the

full screen.

SLOT2 CH SELECT*⁴

DPORT

This function is available only when SLOT2 CH SETTING is 1CH.

TMDS

Shows the DisplayPort signal from slot 2 type PC option into full entire screen.

Shows the TMDS signal from slot 2 type PC option into full entire screen.

TMDS

120Hz

(not adjustable)

TOUCH PANEL

RESET

(not adjustable)

Resets the following settings within the ADVANCED OPTION1 menu back to factory setting:

INPUT DETECT (priority of input signals only), INPUT CHANGE (except for INPUT1 and

INPUT2), TERMINAL SETTINGS, DEINTERLACE, MOVIE SETTINGS, OVER SCAN, AUDIO in

OPTION SETTINGS.

*1: If SPECTRAVIEW ENGINE is ON, this function is grayed out.

*2: This function depends on INPUT CONFIGURATION setting.

*3: Depends on signal input.

*4: This function depends on which option board you use.

*5: When you select OPTION for signal input, this function depends on which option board you use.

English-30

ADVANCED OPTION2

AUTO DIMMING*

Adjusts the backlight of the LCD automatically depending on the amount of ambient light.

AUTO BRIGHTNESS

DVI1, DVI2, DPORT, OPTION*¹,

PRESET*², PRESET2*²inputs only.

Adjusts the brightness level according to the input signal.

NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.

OFF

BACKLIGHT DIMMING* Adjusts automatically each of the clusters of the backlight of the LCD independently, according to

the input signal.

ROOM LIGHT

SENSING*

The backlight of the LCD screen can be set to increase or decrease depending on the amount of

ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If

the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the

viewing experience more comfortable to the eye in a variety of lighting conditions.

NOTE: When ROOM LIGHT SENSING is set to MODE1 or MODE2, BACKLIGHT, AUTO

BRIGHTNESS and BACKLIGHT in SCREEN SAVER function are disabled.

OFF

Do not cover the room light sensing sensor when you use MODE1 or MODE2.

AMBIENT parameter setting

ROOM LIGHT SENSING in OSD, select MODE1 or MODE2 and set MAX LIMIT, IN BRIGHT and

IN DARK in each mode.

MAX LIMIT: This is the max level of backlight which you set.

IN BRIGHT: This is the backlight level that the monitor will go up to when the ambient light level is

highest.

IN DARK: This is the level of backlight that the monitor will go down to when the ambient light

level is low.

When the ROOM LIGHT SENSING is enabled the Backlight level of the screen changes

automatically according to the lighting conditions of the room (see ﬁgure below).

Factory Setting

BACKLIGHT range

BACKLIGHT range when

set to MAX LIMIT.

BACKLIGHT level set for

the monitor to use when

ambient lighting level is

low.

BACKLIGHT level set

for the monitor to use

when ambient lighting

level is high.

IN DARK

dark

IN BRIGHT

room bright condition

bright

Screen Backlight value by MODE1

Screen Backlight value by MODE2

MAX LIMIT: BACKLIGHT level is limited to your set level.

IN DARK: BACKLIGHT level set for the monitor to use when ambient lighting level is low.

IN BRIGHT: BACKLIGHT level set for the monitor to use when ambient lighting level is high.

HUMAN SENSING*³

HUMAN SENSING has three settings.

DISABLE

NOTE: POWER SAVE is disabled when AUTO OFF or CUSTOM is selected in HUMAN

SENSING.

DISABLE

No human sensing.

AUTO OFF

At the preset time, when no person is detected, BACKLIGHT* and VOLUME automatically go

into OFF. When a person comes near the monitor again, the monitor will automatically return to

normal mode.

CUSTOM

BACKLIGHT* and VOLUME automatically shift to the set value when detecting no person. When

a person comes near the monitor again, the monitor automatically return to normal mode and

display the input signal selected in INPUT SELECT.

INTELLI. WIRELESS DATA Select “ON” to activate INTELLIGENT WIRELESS DATA function (see page 47). A password is

required when using the function.

SPECTRAVIEW ENGINE

RESET

Select “ON” to activate SPECTRAVIEW ENGINE (see page 19).

OFF

Resets “ADVANCED OPTION 2” settings back to factory setting, except for INTELLI. WIRELESS

DATA.

FACTORY RESET

All items are returned to factory shipment state.

NOTE: You can reset all items in all daisy chain displays. Please be careful to avoid resetting all

items inadvertently.

*: If SPECTRAVIEW ENGINE is ON, this function is grayed out.

*1: This function depends on which option board you use.

*2: This function depends on INPUT CONFIGURATION setting.

*3: The function is available only when connecting the optional control unit.

English-31

NOTE 1: CREATING A SCHEDULE

The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be programmed.

To program the schedule:

1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET/POINT ZOOM or the + button

to enter the Settings menu. Highlight the desired schedule number and press SET/POINT ZOOM. The box next to the number will turn yellow.

The schedule can now be programmed.

2. Use the down button to highlight the hours setting in the ON time slot. Use the + and - buttons to set the hour. Use the up and down buttons to

highlight the minutes setting. Use the + and - buttons to set the minutes. Set the OFF time in the same manner.

3. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to highlight

PIC. MODE. Use the + and - buttons to choose the picture mode.

4. Use the down button to select a day on which the schedule will be enabled. Push the

SET/POINT ZOOM button to enable. If the schedule is to be ran every day, choose

EVERY DAY and press the SET/POINT ZOOM button. The circle next to EVERY DAY

will turn yellow. If a weekly schedule is desired, choose the days of the week using the up OFF TIMER

and down buttons and pressing SET/POINT ZOOM to select. Then highlight the EVERY

WEEK option and press SET/POINT ZOOM.

DVI1

SCHEDULE:

(THU) JUN.18.2009 15:38

SETTINGS:

SCHEDULE SETTINGS

SCHEDULE LIST

DATE & TIME

RESET

ON:

– – : – –

– – – –

OFF:

INPUT:

PIC. MODE:

5. After a schedule is programmed the remaining schedules can then be set. Press MENU

to leave the OSD or press EXIT to go back to the previous menu.

EVERY DAY

EVERY WEEK

MON

TUE

FRI

WED

SAT

THU

SUN

NOTE: If schedules are overlapping then the schedule with the highest number will have

priority over the schedule with the lowest number. For example schedule #7 will have

priority over schedule #1.

Return

Choose

Mark

If selected input or picture mode is not available now, disable input or picture mode

is shown in red.

NOTE 2: IMAGE PERSISTENCE

Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a

residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not

permanent, but constant images being displayed for a long period of time should be avoided.

To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the

monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at

regular intervals whenever the screen is idle or turning off the monitor when not in use.

Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.

For long life use as Public Display

Image Sticking of LCD Panel

When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or

“ghost” image of previous image may be observed. (Image Persistence)

Image Persistence is not permanent, but when ﬁxed image is displayed for long period, ionic impurities inside LCD are accumulated along the

displayed image, and may be permanent. (Image Sticking)

Recommendations

To prevent Image Sticking, and for longer life usage of LCD, the following are recommended.

1. Fixed image should not be displayed for long period. Change ﬁxed images after short intervals.

2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule Functions.

3. Lower environmental temperatures prolong the lifespan of the monitor.

When Protective surface (glass, acrylic) is installed over the LCD surface, the LCD surface is located in an enclosed space, the monitor are

stacked, utilize the temperature sensors inside monitor.

To reduce the environmental temperature, use the Cooling Fan, Screen Saver and Low Brightness.

4. Please use “Screen Saver Mode” of monitor.

English-32

Remote Control Function

REMOTE CONTROL ID FUNCTION

Monitor ID:1

Monitor ID:2

Monitor ID:3

REMOTE CONTROL ID

The remote control can be used to control up to 100 individual MultiSync monitors using

what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode

works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync

monitors. For example: if there are many monitors being used in the same area, a remote

control in normal mode would send signals to every monitor at the same time (see

Figure 1). Using the remote in REMOTE CONTROL ID mode will only operate one speciﬁc

monitor within the group (see Figure 2).

Remote works

Figure 1

Remote in

Normal mode or

the REMOTE ID

is set to 0

TO SET REMOTE CONTROL ID

While holding down the REMOTE ID SET button on the remote control, use the KEYPAD to

input the Monitor ID (1-100) of the display to be controlled via remote. The remote can then

be used to operate the monitor having that speciﬁc Monitor ID number.

When 0 is selected or when the remote control is in normal mode, all monitors will be

operated.

Monitor ID:1

Monitor ID:2

Monitor ID:3

TO SET/RESET REMOTE CONTROL MODE

ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for

2 seconds.

Remote does

not work

Remote does

not work

Remote works

Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold

down for 2 seconds.

In order for this feature to work properly, the display must be assigned a Monitor ID number.

The Monitor ID number can be assigned under the MULTI DISPLAY menu in the OSD

(See page 27).

Figure 2

Remote set up

to use REMOTE

ID:3

Point the remote control towards the remote sensor of the desired monitor and press the

REMOTE ID SET button. The MONITOR ID number is shown on the display when your

remote control is in ID mode.

Use the remote control to operate a monitor that has a speciﬁc MONITOR ID number assigned to it.

1. Set the MONITOR ID number for the display (See page 27). The MONITOR ID number can range from 1-100.

This MONITOR ID number allows the remote control to operate this speciﬁc monitor without affecting other monitors.

2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number

(1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose “0” to simultaneously

control all displays in range.

3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button.

The MONITOR ID number is shown in red on the display.

If the REMOTE CONTROLID is “0”, then all displays in range will show their respective MONITOR ID number in red.

If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same.

NOTE: GROUP ID cannot be speciﬁed via the remote control.

English-33

Multiple Monitors Connection

You can control multiple monitors by using RS-232C, REMOTE IN or LAN daisy-chain connection.

NOTE:

Multiple monitors that are daisy-chained have a limit to the connectable monitors.

When manually specify the ID number or control by the speciﬁed ID number, please execute AUTO ID (see page 27)

previously.

Main Monitor

Connector

Sub Monitors

Connector

OUT

RS-232C

REMOTE IN

LAN1

LAN2

LAN1

LAN2

Connection

MultiSync

LAN1 LAN2

LAN Cable

MultiSync

English-34

Controlling the LCD monitor via RS-232C Remote Control

This LCD monitor can be controlled by connecting a personal computer with a RS-232C (reverse type) terminal.

Functions that can be controlled by a personal computer are:

•

Power ON or OFF.

Switching between input signals.

Sound Mute ON or OFF.

Connection

LCD Monitor + computer

MultiSync

computer

RS-232C

RS-232C Cable

NOTE:

If your computer is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact

your dealer for details.

For the pin assignment, please see “2) RS-232C input/output” below.

To control a monitor, please use the control command. Instructions for the control command can be found on the CD included

with the display. The ﬁle is called “External_control.pdf”.

1) Interface

PROTOCOL

BAUD RATE

DATA LENGTH

PARITY BIT

STOP BIT

RS-232C

9600 [bps]

8 [bits]

NONE

1 [bit]

FLOW CONTROL NONE

This LCD monitor uses RXD, TXD and GND lines for RS-232C control.

The reverse type cable (null modem cable) (not include) should be used for RS-232C control.

2) PIN ASSIGNMENT

RS-232C input/output

Pin No Name

D-SUB 9P (Monitor side)

RXD

TXD

GND

This LCD monitor uses RXD, TXD and GND lines for RS-232C control.

English-35

3) Control command diagram

For other commands, please see “External_Control.pdf” ﬁle on the CD-ROM.

Function (Monitor ID = 1)

Code Data

Power ON

01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 31 03 73 0d

01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 34 03 76 0d

Power OFF

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 46 03 04 0d

Input Source Select DisplayPort

Input Source Select DVI1

Input Source Select DVI2

Input Source Select HDMI1

Input Source Select HDMI2

01 30 41 30 45 30 41 02 31 31 30 36 30 30 30 46 03 04 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 33 03 71 0d

01 30 41 30 45 30 41 02 31 31 30 36 30 30 30 33 03 71 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 34 03 76 0d

01 30 41 30 45 30 41 02 31 31 30 36 30 30 30 34 03 76 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 31 03 72 0d

01 30 41 30 45 30 41 02 31 31 30 36 30 30 31 31 03 72 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 32 03 71 0d

01 30 41 30 45 30 41 02 31 31 30 36 30 30 31 32 03 71 0d

Input Source Select HDMI3

Input Source Select HDMI4

01 30 41 30 45 30 41 02 31 31 30 36 30 30 38 32 03 78 0d

01 30 41 30 45 30 41 02 31 31 30 36 30 30 38 33 03 79 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 44 03 06 0d

Input Source Select OPTION

01 30 41 30 45 30 41 02 31 31 30 36 30 30 30 44 03 06 0d

Sound Mute ON

Sound Mute OFF

01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 31 03 09 0d

01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 32 03 0a 0d

English-36

Controlling the LCD monitor via LAN Control

Connecting to a Network

Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function.

To use a LAN connection, you are required to assign an IP address.

Example of LAN connection:

Server

NOTE: Use a category 5 or higher LAN cable.

Hub

LAN cable

(not supplied)

Network Setting by Using an HTTP Browser

Overview

Connecting the monitor to a network allows for monitor control from a computer via the network.

To perform the monitor control from a web browser, you must have an exclusive application installed on your computer.

The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP

server function. Please be sure to use “Microsoft Internet Explorer 7.0” or a higher version for the web browser.

(This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will

vary depending on the version of browser. Please refer to the help ﬁles and the other information provided in your software.)

Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the

monitor and entering the following URL.

Network Setting

http://<the Monitor’s IP address>/index.html

TIP:

The default IP address is assigned automatically to the monitor.

The exclusive application can be downloaded from our website.

NOTE:

If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to

refresh your web browser (or clear the cache).

The display or button’s response can be slowed down or operation may not be accepted depending the settings of

your network. Should this happen, consult your network administrator.

The LCD monitor may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a

moment and repeat. If you still can’t get a response, turn the monitor off and then back on.

To control a monitor please use the control command. See “Control command diagram” (page 36).

English-37

Preparation Before Use

Connect the monitor to a commercially available LAN cable before engaging in browser operations.

Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting

method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be

displayed depending on the effectiveness of the cache, and the contents set from the browser may not be reﬂected in operation.

It is recommended that a proxy server not be used unless it is unavailable.

Handling of the Address for Operation via a Browser

The host name can be used under the following cases:

If the host name corresponding to the IP address of the monitor has been registered to the domain name server (DNS) by the

network administrator, you can then access the network settings of the display via that registered host name using a compatible

browser.

If the host name corresponding to the IP address of the monitor has been conﬁgured in the “HOSTS” ﬁle of the computer being

used, you can then access the network settings of the display via that host name using a compatible browser.

Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by

specifying http://pd.nec.co.jp/index.html for the address or the entry column of the URL.

Example 2: When the IP address of the monitor is “192.168.73.1”, access is gained to the mail alert settings by specifying

http://192.168.73.1/index.html for the address or the entry column of the URL.

Operation

Access the following address to show HOME. Click each link on the left side of HOME.

http://<the Monitor’s IP address>/index.html

REMOTE CONTROL

Enable to control equivalent as the remote control key.

OSD menu

Enable to set the following OSD menu.

PICTURE, ADJUST, AUDIO, SCHEDULE, MULTI PICTURE CONTROL, OSD, MULTI DISPLAY, DISPLAY PROTECTION,

EXTERNAL CONTROL, ADVANCED OPTION1, ADVANCED OPTION2.

NOTE:

Function of buttons which are shown on setting pages.

[APPLY]: Reﬂect your settings.

[CANCEL]: Return to the previous settings. NOTE: CANCEL is disabled after clicking APPLY.

[RELOAD]: Reload the settings.

[RESET]: Resets to the initial setting.

English-38

Network Setting

Click “NETWORK” on the left side of HOME.

IP SETTING

Set for IP ADDRESS setting.

AUTO: Automatically assign an IP address.

MANUAL: Set your IP address of the network connected to the monitor.

NOTE: Consult your network administrator for the IP address when [AUTO] is selected for

[IP SETTING].

IP ADDRESS

Set your IP address of the network connected to the monitor when [MANUAL] is selected for

[IP SETTING].

SUBNET MASK

Set your subnet mask number of the network connected to the monitor when [MANUAL] is selected

for [IP SETTING].

DEFAULT GATEWAY Set your default gateway of the network connected to the monitor when [MANUAL] is selected for

[IP SETTING].

NOTE: Set as [0.0.0.0] to delete the setting.

DNS

Set for IP ADDRESS setting of DNS server.

AUTO: Automatically assign an IP address of DNS server connected to the monitor.

MANUAL: Set your IP address of DNS server connected to the monitor.

PRIMARY DNS

Set your primary DNS settings of the network connected to the monitor.

NOTE: Set as [0.0.0.0] to delete the setting.

SECONDARY DNS

Set your secondary DNS settings of the network connected to the monitor.

NOTE: Set as [0.0.0.0] to delete the setting.

NOTE:

The following settings will reset back to the factory setting when “IP ADDRESS RESET” is selected by an EXTERNAL

CONTROL of OSD:

[IP SETTING]: AUTO, [IP ADDRESS]: 192.168.0.10, [SUBNET MASK]: 255.255.255.0, [DNS]: AUTO [DEFAULT

GATEWAY], [PRIMARY DNS] and [SECONDARY DNS] are blank.

English-39

Mail Setting

Click “MAIL” on the left side of HOME.

This option notiﬁes your computer of an error message via e-mail when using wired LAN. An error message notiﬁcation will be

sent when an error occurs in the monitor.

ALERT MAIL

Checking [ENABLE] will turn on the Alert Mail feature.

Checking [DISABLE] will turn off the Alert Mail feature.

STATUS MESSAGE

Checking [ENABLE] will turn on the STATUS MESSAGE feature.

Checking [DISABLE] will turn off the STATUS MESSAGE feature.

SENDER’S ADDRESS

SMTP SERVER

Type in the senders address. Up to 60 alphanumeric and symbols characters can be used.

Type in the SMTP server name to be connected to the monitor.

Up to 60 alphanumeric characters can be used.

RECIPIENT’S

Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.

ADDRESS 1 TO 3

AUTHENTICATION

METHOD

This selects the authentication method of the e-mail transmission.

POP3 SERVER

USER NAME

This speciﬁes the address of the POP3 server that is used in the authentication of the e-mail.

This sets the user name for logging into the authentication server when authentication is required

for the e-mail transmission. Up to 60 alphanumeric characters can be used.

PASSWORD

TEST MAIL

This sets the password for logging into the authentication server when authentication is required for

the e-mail transmission. Up to 60 alphanumeric characters can be used.

Click this button to send a test mail to check if your settings are correct.

NOTE:

• If you execute a test, you may not receive an Alert mail.

Should this happen, check if the network settings are correct.

• If you entered an incorrect address in a test, you may not receive an Alert mail.

Should this happen, check if the Recipient’s Address is correct.

TIP:

For Control command diagram, please see ﬁle “External_Control.pdf” on the CD-ROM.

English-40

Alert error message list

Error number

* ErrorCode

Alert mail Message

Explanation

Measure

The monitor’s power supply is not

functioning normally.

Standby power Abnormal

Please contact your supplier.

70h ~ 7Fh

80h ~ Fh

The cooling fan has stopped.

Cooling fan Abnormal

Backlight abnormal

Please contact your supplier.

The monitor’s back light unit is not

functioning normally.

90h ~ 9Fh

A0h ~ AFh

The monitor is overheated.

Temperature Abnormal

Please contact your supplier.

SENSOR reached at the temperature

that the user had speciﬁed.

Reconﬁrm the setting condition from

OSD (DISPLAY PROTECTION-FAN

CONTROL) or please contact your

supplier.

A2h

*condition: DISPLAY PROTECTION-FAN

CONTROL-COOLING FAN = AUTO

The monitor doesn’t have the input

signal.

No signal

Please check “No picture” in

“Troubleshooting”.

B0h ~ BFh

D0h

The remaining capacity of the error log Proof of Play log memory size is 1 more

decreased.

Please get a log by using PD external

command. See page 46.

hour.

The system error occurred in the

monitor.

System error.

Please contact your supplier.

E0h ~ EFh

Sample: The following examples are content of Alert Mail that informs the temperature anomaly of monitor.

Sample: The following examples are content of test mail by browser.

English-41

SNMP Setting

Click “SNMP” on the left side of HOME.

This function allows for getting status and controlling of a monitor via the network.

Version:

SNMP v1 Authenticated plaintext by community name, not return a conﬁrmation message of Trap.

SNMP v2c Authenticated plaintext by community name, return a conﬁrmation message of Trap.

Community name:

The default setting of community name is “public”. It is read only. You can set community names for up to 3 settings.

Trap:

Sending error message to speciﬁed address when an error occurs in the monitor.

Check Box

Temperature

Explanation

Temperature abnormal

Cooling fan abnormal

Power abnormal

Error code

0xA0, 0xA1, 0xA2

Fan

0x80, 0x81

Power

0x70, 0x71, 0x72, 0x78

Inverter/Backlight

No Signal

Inverter or backlight abnormal 0x90, 0x91

No signal

0xB0

0xD0

0xE0

PROOF OF PLAY

System Error

Lower the log storage

System error

English-42

AMX Setting

Click “AMX” on the left side of HOME.

AMX BEACON

Turn on or off for detection from AMX Device Discovery when connecting to the network supported by

AMX’s NetLinx control system.

TIP:

When using a device that supports AMX Device Discovery, all AMX NetLinx control system will

recognize the device and download the appropriate Device Discovery Module from an AMX server.

Checking [ENABLE] will detect the device from AMX Device Discovery.

Checking [DISABLE] will not detect the device from AMX Device Discovery.

CRESTRON Setting

Click “CRESTRON” on the left side of HOME.

CRESTRON ROOMVIEW compatibility

The monitor supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and

controlled from a computer or a controller.

For more information, visit http://www.crestron.com

ROOMVIEW

ROOMVIEW for managing from the computer.

ON: Enables ROOMVIEW.

OFF: Disables ROOMVIEW.

CRESTRON

CONTROL

CRESTRON CONTROL for managing from the controller.

ON: Enables CRESTRON CONTROL.

OFF: Disables CRESTRON CONTROL.

CONTROLLER IP

ADDRESS

Set your IP address of CRESTRON SERVER.

IP ID

Set your IP ID of CRESTRON SERVER.

TIP: The CRESTRON settings are required only for use with CRESTRON ROOMVIEW.

For more information, visit http://www.crestron.com

English-43

Name Setting

Click “NAME” on the left side of HOME.

MONITOR NAME

HOST NAME

Set a monitor name. The name must be 16 characters or less. The default is model name.

Type in the hostname of the network connected to the monitor.

Up to 15 alphanumeric characters can be used.

DOMAIN NAME

Type in the domain name of the network connected to the monitor.

Up to 60 alphanumeric characters can be used.

Network Password Setting

Click “NETWORK PASSWORD” on the left side of HOME.

PJLink PASSWORD Set a password for PJLink*. A password must be 32 characters or less. Do not forget your password.

However, if you forget your password, consult with your dealer.

HTTP PASSWORD

Set a password for HTTP server. A password must be 10 characters or less.

HTTP PASSWORD

ENABLE

HTTP PASSWORD is required when logging in HTTP server.

Set a monitor name as USER NAME when inputting the password.

*What is PJLink?

PJLink is a standardization of protocol used for controlling devices of different manufacturers. This standard protocol is

established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005.

The device supports all the commands of PJLink Class 1.

English-44

PD List Information

Click “PD LIST” on the left side of HOME.

Show the list of ID and IP address of multiple monitors that are daisy-chained.

Only the master monitor can show the list.

Memo Setting

Click “MEMO” on the left side of HOME.

Set a title and message.

TITLE

A title must be 24 characters or less.

MESSAGE

A message must be 240 characters or less.

MEMO PASSWORD The default is “0000”.

MEMO PASSWORD MEMO PASSWORD is required when setting MEMO.

ENABLE

English-45

POINT ZOOM

Using “SET/POINT ZOOM” button on a remote control allows to enlarge a partial of image.

Press CH+/- button to zoom up or down. The image can be expanded from 1 to 10 times.

Press [SET/POINT ZOOM] button on a remote control. An icon will be a magniﬁer.

Move magniﬁer icon by [ ] [ ] [+] [-] button.

Press [CH+] to zoom up. Press [CH-] to zoom down.

Press [SET/POINT ZOOM] to disappear the icon.

Press [EXIT] to return to a normal size.

Press [MENU] to display OSD menu.<Setting Procedure>

NOTE:

• The image may be distorted during this function.

• This function does not work when set to IMAGE FLIP except for NONE, MULTI PICTURE MODE, SCREEN

SAVER, SUPER in INPUT CHANGE, INPUT CONFIGURATION, ROTATE, TEXT TICKER.

• When selected DYNAMIC or ZOOM in ASPECT, the image will be changed FULL, then start to POINT ZOOM.

After POINT ZOOM, the ASPECT will be returned previous ASPECT settings. When the ASPECT is changed

during POINT ZOOM, DYNAMIC and ZOOM will be FULL image.

• The magniﬁer icon does not move to no image area.

• POINT ZOOM will be released after changing input signal or power off.

• POINT ZOOM will be released when changing ASPECT setting during POINT ZOOM.

• When this function is active, STILL is not available.

• POINT ZOOM is not available with 3840 x 2160 (60 Hz) signal.

PROOF OF PLAY

This function allows to send message for the current status of monitor by self checking.

Check item

INPUT

Message

DVI1, DVI2, DPORT, HDMI1, HDMI2, HDMI3, HDMI4, OPTION*, PRESET1*¹, PRESET2*¹

ex. (H)1920, (V)1080 , (H)1360, (V)768 or No signal or Invalid signal

LINE IN, DPORT, HDMI1, HDMI2, HDMI3, HDMI4, OPTION*

Audio in or No Audio in or N/A (LINE IN, OPTION*)

Normal Picture or No Picture

①

②

③

④

⑤

⑥

⑦

Resolution

AUDIO INPUT

Audio signal

Picture Image

LINE OUT

TIME

Normal Audio or No Audio

(year)/(month)/(day)/(hour)/(minutes)/(second)

*: This function depends on which option board you use.

*1: This function depends on INPUT CONFIGURATION setting.

Sample:

HDMI

①

②

③

④

⑤

⑥

⑦

1920 x 1080

HDMI

Audio in

Normal Picture

Normal Audio

2014/1/1/0h/0m/0s

NOTE:

For Proof of Play function, please see “External_Control.pdf” on the CD-ROM.

English-46

INTELLIGENT WIRELESS DATA

This function allows to get the data of monitor’s status by wireless communication even while the monitor is off.

Some menu of OSD, you can set by this function.

NOTE:

Sensor position: See page 9.

Please contact your supplier for detailed information.

Function name

Setting Copy

Setting read and write function

Display information

Security Setting

English-47

Features

Reduced Footprint: Provides the ideal solution for environments with superior image quality.

SPECTRAVIEW ENGINE: This system is designed for professionals with color-critical applications.

Each display screen is calibrated at factory. By making adjustments directly in the display hardware, optimal settings are

conﬁgured without any user interaction.

OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six

axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard provides

the monitor with a uniform color proﬁle. This assures that the colors displayed on the monitor are exactly the same as on the

color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your screen

and customise the color accuracy of your monitor to a variety of standards.

sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays and

other peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation and

backward compatibility with other common color standards.

OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use

on-screen menus.

Plug and Play: The Microsoft^®solution with the Windows^®operating system facilitates setup and installation by allowing

the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically

optimizing display performance.

IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a

lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and

lowering the air conditioning costs of the workplace.

FullScan Capability: Allows you to use the entire screen area in most resolutions, signiﬁcantly expanding image size.

VESA Standard (FDMIv1) Mounting Interface: Allows you to connect your LCD monitor to any VESA standard (FDMIv1) third

party mounting arm or bracket. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard

in North America.

DVI-D: The digital-only subset of DVI ratiﬁed by the Digital Display Working Group (DDWG) for digital connections between

computers and displays. As a digital-only connector, analog support is not provided for a DVI-D connector. As a DVI-based

digital only connection, only a simple adapter is necessary for compatibility between DVI-D and other DVI-based digital

connectors such as DFP and P&D. The DVI interface of this display supports HDCP. The DVI interface of this display supports

DVI Dual Link.

ZOOM: Expands/reduces image size for horizontal and vertical direction.

Self-diagnosis: If an internal error should occur, a failure state will be indicated.

USB hub adds excitement to your computing by connecting you to digital cameras, scanners and more.

HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent

over a digital signal. If you are unable to view material via the digital input, this does not necessarily mean the display is not

functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP and

might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).

Option board slot: You can use an option board. Please contact your supplier for detailed information.

English-48

Troubleshooting

Image is blinking

No picture

•

If you use a repeater, distributor, long cable, this may

cause image roughness or blink for a moment. Please set

the LONG CABLE COMP in that case. if the state of the

screen is not improved, please connect the cable to the

monitor directly without using a repeater or a distributor,

or replace the cable of use.

•

The signal cable should be completely connected to the

display card/computer.

•

The display card should be completely seated in its slot.

Check the main Power Switch, it should be in the ON

position.

•

Power Switch and computer power switch should be in

the ON position.

•

Some HDMI cable may not display an image correctly.

If input resolution is 1920 x 2160, 3840 x 2160 or

4096 x 2160, please use the HDMI cable that supports

4K resolution.

Check to make sure that a supported mode has been

selected on the display card or system being used.

(Please consult display card or system manual to change

graphics mode.)

Image is unstable, unfocused or swimming is apparent

•

Signal cable should be completely attached to the

computer.

•

Check the monitor and your display card with respect to

compatibility and recommended settings.

•

Use the OSD Image Adjust controls to focus and adjust

display by increasing or decreasing the ﬁne adjustment.

When the display mode is changed, the OSD Image

Adjust settings may need to be re-adjusted.

Check the signal cable connector for bent or pushed-in

pins.

The monitor automatically goes into OFF at the preset

time period after signal is lost. Press the power button.

•

Check the monitor and your display card with respect to

compatibility and recommended signal timings.

Check the DVI MODE setting when DVD player or

computer equipment is connected to the DVI input.

If your text is garbled, change the video mode to non-

interlace and use 60Hz refresh rate.

•

Check HDMI/DVI SELECT setting.

Check the DVI cable you use. If input resolution is

1920 x 2160 or 3840 x 2160, DVI Dual Link cable needs

to be used.

The image may be distorted when turning the power on or

changing the settings.

LED on monitor is not lit

(no green or red color can be seen)

•

Check the OPTION POWER setting when you use option

board accessories.

•

Power Switch should be in the ON position and power

cord should be connected.

Snowy Picture, Black Screen in DVI input

•

Check the DVI MODE setting when DVD player or

computer equipment is connected to the DVI input.

Check the main Power Switch, it should be in the ON

position.

Make certain the computer is not in a power-saving mode

(touch the keyboard or mouse).

Power Button does not respond

•

Unplug the power cord of the monitor from the AC outlet

to turn off and reset the monitor.

Check to see that the power indicator option in the OSD is

set to ON.

•

Check the main Power Switch of the monitor.

RED LED on monitor is blinking

Image persistence

•

A certain failure might have occurred, please contact your

nearest authorized NEC DISPLAY SOLUTIONS service

facility.

•

Please be aware that LCD Technology may experience

a phenomenon known as Image Persistence. Image

Persistence occurs when a residual or “ghost” image of

a previous image remains visible on the screen. Unlike

CRT monitors, LCD monitors’ image persistence is not

permanent, but constant images being displayed for

a long period of time should be avoided. To alleviate

image persistence, turn off the monitor for as long as the

previous image was displayed. For example, if an image

was on the monitor for one hour and a residual image

remains, the monitor should be turned off for one hour to

erase the image.

•

If the monitor is powered off by the inside temperature

being higher than the normal operating temperature, a

RED LED will blink six times. Power on the display again

after conﬁrming the inside temperature has been reduced

to normal operation temperature.

Display image is not sized properly

•

Use the OSD Image Adjust controls to increase or

decrease the coarse adjustment.

•

Check to make sure that a supported mode has been

selected on the display card or system being used.

(Please consult display card or system manual to change

graphics mode).

NOTE:

As with all personal display devices, NEC

DISPLAY SOLUTIONS recommends displaying

moving images and using a moving screen saver

at regular intervals whenever the screen is idle or

turning off the monitor when not in use.

English-49

No Sound

•

Check to see if audio cable is properly connected.

Check to see if mute is activated.

Check to see if volume is set at minimum.

Check to see if computer supports an audio signal

through DisplayPort.

If unsure, contact the computer manufacturer.

•

When LINE OUT is not functioning, check to see if

SURROUND is ON.

Check Internal/External speaker switch.

Remote Control is not available

•

Check the Remote Control’s batteries status.

Check if batteries are inserted correctly.

Check if the Remote Control is pointing at the monitor’s

remote sensor.

•

Check the IR LOCK SETTINGS status.

The remote control system may not function when direct

sunlight or strong illumination strikes the remote control

sensor of the LCD monitor, or when there is an object in

the path.

“SCHEDULE”/“OFF TIMER” function is not working

properly

•

The “SCHEDULE” function will be disabled when the

“OFF TIMER” is set.

•

If the “OFF TIMER” function is enabled and the power to

the LCD monitor is turned off when the power supply is

interrupted unexpectedly, then the “OFF TIMER” will be

reset.

Snowy Picture, Poor Sound in TV

•

Check antenna/cable connection. Use new cable if

necessary.

USB Hub does not operate

•

Check to make sure the USB cable is properly connected.

Refer to your USB device User’s Manual.

•

Check if the USB upstream port on the monitor is

connected to the USB downstream port on the computer.

And make sure the computer is ON.

Interference in TV

•

Check components for shielding, move away from

monitor if necessary.

RS-232C or LAN control is not available

•

Check RS-232C (reverse type) or LAN cable (category 5

or higher) connection.

Either light vertical or horizontal stripes may appear, depending on the speciﬁc display pattern. This is no product fault or degradation.

English-50

Speciﬁcations - X841UHD-2

Product Speciﬁcations

LCD Module

84”/2134.6 mm diagonal

Pixel Pitch: 0.4845 mm

Resolution: 3840 x 2160

Color: Over 1073 million colors (depending on display card used)

Brightness: 500 cd/m²(Max.) @25°C

Contrast Ratio: 1400:1

Viewing Angle: 89° (typ) @ CR>10

Frequency

Horizontal: 31.5 kHz - 133.3 kHz (Digital Input)

Vertical: 24.0 - 85.0 Hz

Pixel Clock

Viewable Size

Input Signal

DVI

25 MHz - 300 MHz (HDMI), 25 MHz - 330 MHz (Dual Link), 25 MHz - 540 MHz (DisplayPort)

1860.5 x 1046.5 mm

DVI-D 24pin

(Dual Link)

Digital RGB

DVI (HDCP)

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, 1920 x 1080 (60 Hz),

1920 x 2160 (60 Hz), 3840 x 2160 (30 Hz),1080p, 1080i

DisplayPort DisplayPort Connector Digital RGB

DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60, 1920 x 1080 (60 Hz),

1920 x 2160 (60 Hz), 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz,

3840 x 2160 (60 Hz (DisplayPort1.2)/30 Hz/24 Hz)

HDMI

HDMI Connector

Digital YUV

Digital RGB

HDMI

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60, 1920 x 1080 (60 Hz),

1920 x 2160 (60 Hz), 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz,

576i@50Hz, 480i@60Hz, 3840 x 2160 (30 Hz/24 Hz/25 Hz), 4096 x 2160 (24 Hz)*^1,*³

AUDIO

LINE IN

Stereo Mini Jack

HDMI Connector

Analog Audio

Digital Audio

Stereo L/R 0.5 Vrms

PCM 32, 44.1, 48 KHz (16/20/24bit)

Stereo L/R 0.5 Vrms

DisplayPort Connector Digital Audio

LINE OUT Stereo Mini Jack

Speaker Output

Analog Audio

External Speaker Jack 15 W + 15 W (8 ohm)

Internal Speaker 10 W + 10 W (Stereo)

Control

RS-232C In: 9 Pin D-sub

LAN: RJ-45 10/100 BASE-T

Remote IN: Stereo Mini Jack 3.5 ɸ

USB Hub

I/F: USB Speciﬁcation Revision 2.0

Port: Upstream 1

Downstream 1

Load Current: Maximum 0.5 A per port

Service port

USB service port for maintenance

6.7 - 2.7 A @ 100-240V AC, 50/60Hz

Power Supply

Operational Environment

Temperature*²: 0 - 40°C / 32 - 104°F

Humidity: 20 - 80% (without condensation)

Altitude: 0 - 3000 m (Brightness may decrease with altitude)

Storage Environment

Temperature: -20 - 60°C / -4 - 140°F

Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C

Dimension

1931 (W) x 1117 (H) x 85 (D) mm / 76.0 (W) x 44.0 (H) x 3.3 (D) inches

Weight

70.5 kg (155.4 lbs)

VESA compatible mounting interface

Power Management

Plug & Play

400 mm x 400 mm (M8, 4 Holes)

VESA DPM

VESA DDC2Bi, DDC/CI, DisplayPort

16V/3.6 A

Power supply for Slot 2 type OPTION

Accessories

Setup manual, Power Cord, Video Signal cable, Remote Control, AAA Battery x 2, Clamp x 1,

Screw x 1, CD-ROM

NOTE: Technical speciﬁcations are subject to change without notice.

*1: Compressed image.

*2: When you use option board accessories, please contact your supplier for detailed information.

*3: Displayed text may be blurred.

English-51

Speciﬁcations - X981UHD-2

Product Speciﬁcations

LCD Module

98”/2477.0 mm diagonal

Pixel Pitch: 0.5622 mm

Resolution: 3840 x 2160

Color: Over 1073 million colors (depending on display card used)

Brightness: 500 cd/m²(Max.) @25°C

Contrast Ratio: 1300:1

Viewing Angle: 89° (typ) @ CR>10

Frequency

Horizontal: 31.5 kHz - 133.3 kHz (Digital Input)

Vertical: 24.0 - 85.0 Hz

Pixel Clock

Viewable Size

Input Signal

DVI

25 MHz - 300 MHz (HDMI), 25 MHz - 330 MHz (Dual Link), 25 MHz - 540 MHz (DisplayPort)

2158.8 x 1214.4 mm

DVI-D 24pin

(Dual Link)

Digital RGB

DVI (HDCP)

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, 1920 x 1080 (60 Hz),

1920 x 2160 (60 Hz), 3840 x 2160 (30 Hz),1080p, 1080i

DisplayPort DisplayPort Connector Digital RGB

DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60, 1920 x 1080 (60 Hz),

1920 x 2160 (60 Hz), 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz,

3840 x 2160 (60 Hz (DisplayPort1.2)/30 Hz/24 Hz)

HDMI

HDMI Connector

Digital YUV

Digital RGB

HDMI

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60, 1920 x 1080 (60 Hz),

1920 x 2160 (60 Hz), 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz,

576i@50Hz, 480i@60Hz, 3840 x 2160 (30 Hz/24 Hz/25 Hz), 4096 x 2160 (24 Hz)*^1,*³

AUDIO

LINE IN

Stereo Mini Jack

HDMI Connector

Analog Audio

Digital Audio

Stereo L/R 0.5 Vrms

PCM 32, 44.1, 48 KHz (16/20/24bit)

Stereo L/R 0.5 Vrms

DisplayPort Connector Digital Audio

LINE OUT Stereo Mini Jack

Speaker Output

Analog Audio

External Speaker Jack 15 W + 15 W (8 ohm)

Internal Speaker 10 W + 10 W (Stereo)

Control

RS-232C In: 9 Pin D-sub

LAN: RJ-45 10/100 BASE-T

Remote IN: Stereo Mini Jack 3.5 ɸ

USB Hub

I/F: USB Speciﬁcation Revision 2.0

Port: Upstream 1

Downstream 1

Load Current: Maximum 0.5 A per port

Service port

USB service port for maintenance

7.7 - 3.0 A @ 100-240V AC, 50/60Hz

Power Supply

Operational Environment

Temperature*²: 0 - 40°C / 32 - 104°F

Humidity: 20 - 80% (without condensation)

Altitude: 0 - 3000 m (Brightness may decrease with altitude)

Storage Environment

Temperature: -20 - 60°C / -4 - 140°F

Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C

Dimension

2204.8 (W) x 1259.8 (H) x 108.0 (D) mm / 86.8 (W) x 49.6 (H) x 4.3 (D) inches

Weight

90.6 kg (199.7 lbs)

VESA compatible mounting interface

Power Management

Plug & Play

400 mm x 400 mm (M8, 4 Holes)

VESA DPM

VESA DDC2Bi, DDC/CI, DisplayPort

16V/3.6 A

Power supply for Slot 2 type OPTION

Accessories

Setup manual, Power Cord, Video Signal cable, Remote Control, AAA Battery x 2, Clamp x 1,

Screw x 1, CD-ROM

NOTE: Technical speciﬁcations are subject to change without notice.

*1: Compressed image.

*2: When you use option board accessories, please contact your supplier for detailed information.

*3: Displayed text may be blurred.

English-52

Manufacturer’s Recycling and Energy Information

NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top

priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly

products, and always strive to help deﬁne and comply with the latest independent standards from agencies such as ISO

(International Organisation for Standardization) and TCO (Swedish Trades Union).

Disposing of your old NEC product

The aim of recycling is to gain an environmental beneﬁt by means of re-use, upgrading, reconditioning or reclamation of

material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely

disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures

and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.

All required information concerning the disposal of the product and country-speciﬁc information on recycling facilities can be

found on our following websites:

http://www.nec-display-solutions.com/greencompany/ (in Europe),

http://www.nec-display.com (in Japan) or

http://www.necdisplay.com (in USA).

Energy Saving

This monitor features an advanced energy saving capability. When a Display Power Management signal is sent to the monitor,

the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.

Mode

Power consumption

LED color

Approx. 380 W (X841UHD-2)

Approx. 420 W (X981UHD-2)

Normal Operation*^1,*²

Green

Energy Saving Mode (AUTO POWER SAVE)

Energy Saving Mode*¹(AUTO STANDBY)

Power Off

Less than 0.5 W

Amber

Red

*1: without any option, with factory settings.

*2: depends on destination.

For additional information visit:

http://www.necdisplay.com/ (in USA)

http://www.nec-display-solutions.com/ (in Europe)

http://www.nec-display.com/global/index.html (Global)

For Energy Saving information: [Default setting: AUTO STANDBY]

For ErP requirement:

Setting: DISPLAY PROTECTION

EXTERNAL CONTROL

POWER SAVE

LAN POWER

AUTO STANDBY

OFF

ADVANCED OPTION 1

INPUT DETECT

NONE

Power consumption: 0.5 W or less.

Time for power management function: Approx. 5-600 sec.

For ErP (Network standby) requirement:

Setting: DISPLAY PROTECTION

EXTERNAL CONTROL

POWER SAVE

LAN POWER

INPUT DETECT

AUTO POWER SAVE

OFF

NONE

ADVANCED OPTION 1

Power consumption: 0.5 W or less (with 1 port activating)/2.0 W or less (with all ports activating)

Time for power management function: Approx. 5-600 sec. (Depend on setting)

English-53

WEEE Mark (European Directive 2012/19/EU)

Disposing of your used product: In the European Union

EU-wide legislation as implemented in each Member State requires that used electrical and electronic products

carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors

and electrical accessories, such as signal cables or power cords. When you dispose of such products, please

follow the guidance of your local authority or ask the shop where you purchased the product, or if applicable,

follow applicable legislation or agreement you may have. The mark on electrical and electronic products may

only apply to the current European Union Member States.

Outside the European Union

If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority

and ask for the correct method of disposal.

For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household

waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in

accordance with legislation.

According the EU directive 2006/66/EC, the battery can’t be disposed improperly.The battery shall be separated to

collect by local service.

English-54

Toshiba R410a User Manual
Toshiba Carrier Rav Sp360ct Ul User Manual
Samsung As12cm2x User Manual
Panasonic Kx Tg5832al User Manual
Mitsubishi Electronics Msz Fa25va User Manual
MAKITA HR2410 02 User Manual
GE ASN18 User Manual
EMERSON LC220EM1 User Manual
CRAFTSMAN 137.415030 User Manual
ASUS UX31A User Manual