Large Format Display
User’s Manual
MultiSync X464UN
MultiSync X464UNS
MultiSync X464UNV
MultiSync X554UN
MultiSync X554UNS
MultiSync X554UNV
Please find your model name in the label on the backside of monitor.
Declaration of conformity
FCC Information
1. Use the attached specified cables with this display so as not to interfere with radio and television reception.
(1) Please use the supplied power cord or equivalent to ensure FCC compliance.
(2) Please use a good quality shielded video signal cable.
Use of other cables and adapters may cause interference with radio and television reception.
2. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington,
D.C., 20402, Stock No. 004-000-00345-4.
Windows is a registered trademark of Microsoft Corporation.
NEC is a registered trademark of NEC Corporation.
OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and
Switzerland.
DisplayPort and DisplayPort Compliance Logo are trademarks owned by the Video Electronics Standards
Association.
All other brands and product names are trademarks or registered trademarks of their respective owners.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC
in the United States and other countries.
Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and
areas.
CRESTRON and ROOMVIEW are registered trademarks of Crestron Electronics, Inc. in the United States and other countries.
GPL/LGPL Software Licenses
The product includes software licensed under GNU General Public License (GPL), GNU Lesser General Public License (LGPL),
and others.
For more information on each software, see “readme.pdf” inside the “about GPL&LGPL” folder on the supplied CD-ROM.
English-1
Important Information
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE
PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER
CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has
been included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION: Please use the power cord provided with this monitor in accordance with the table below. If a power cord is not
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
European
Continental
Plug Type
North America
U.K.
Chinese
Japanese
Plug Shape
U.S.A./
Canada
Region
Voltage
Taiwan
110
EU (except U.K.)
230
U.K.
230
China
220
Japan
100
120*
* When operating the MultiSync monitor with its AC 125-240V power supply, use a power supply cord that matches the power
supply voltage of the AC power outlet being used.
NOTE:
This product can only be serviced in the country where it was purchased.
Use the power cord which has BSMI mark at both ends when you use this monitor in Taiwan.
•
•
The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment.
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.
Warning
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
English-2
Safety Precautions, Maintenance & Recommended Use
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTI-FUNCTION MONITOR:
Immediately unplug your monitor from the wall outlet and refer
servicing to qualified service personnel under the following
conditions:
•
DO NOT OPEN THE MONITOR. There are no user
serviceable parts inside and opening or removing covers may
expose you to dangerous shock hazards or other risks. Refer
all servicing to qualified service personnel.
•
•
•
•
•
When the power supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the monitor.
If the monitor has been exposed to rain or water.
If the monitor has been dropped or the cabinet damaged.
•
•
Do not spill any liquids into the cabinet or use your monitor
near water.
If you notice any structural damage such as cracks or
unnatural wobbling.
Do not insert objects of any kind into the cabinet slots, as they
may touch dangerous voltage points, which can be harmful or
fatal or may cause electric shock, fire or equipment failure.
•
If the monitor does not operate normally by following
operating instructions.
•
•
Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or fire.
Recommended Use
•
•
For optimum performance, allow 20 minutes for warm-up.
Do not place this product on a sloping or unstable cart, stand
or table, as the monitor may fall, causing serious damage to
the monitor.
Rest your eyes periodically by focusing on an object at least
5 feet away. Blink often.
•
•
•
•
Position the monitor at a 90° angle to windows and other light
sources to minimize glare and reflections.
•
•
Do not mount this product face up, face down or upside down
for an extended period of time as it may cause permanent
damage to the screen.
Clean the LCD monitor surface with a lint-free, non-abrasive
cloth. Avoid using any cleaning solution or glass cleaner!
The power supply cord you use must have been approved by
and comply with the safety standards of your country. (Type
H05VV-F 3G 1mm2 should be used in Europe)
Adjust the monitor’s brightness, contrast and sharpness
controls to enhance readability.
•
•
In UK, use a BS-approved power cord with molded plug
having a black (13A) fuse installed for use with this monitor.
Avoid displaying fixed patterns on the monitor for long
periods of time to avoid image persistence (after image
effects).
Do not place any objects onto the monitor and do not use the
monitor outdoors.
•
Get regular eye checkups.
•
•
•
•
Do not bend, crimp or otherwise damage the power cord.
If glass is broken, handle with care.
Ergonomics
To realize the maximum ergonomic benefits, we recommend the
following:
Do not cover vent on monitor.
Do not use monitor in high temperature, humid, dusty, or oily
areas.
•
Use the preset Size and Position controls with standard
signals.
•
•
If monitor or glass is broken, do not come in contact with the
liquid crystal and handle with care.
•
•
•
Use the preset Color Setting.
Use non-interlaced signals.
Allow adequate ventilation around the monitor, so that heat
can properly dissipate. Do not block ventilated openings or
place the monitor near a radiator or other heat sources.
Do not put anything on top of the monitor.
Do not use primary color blue on a dark background, as
it is difficult to see and may produce eye fatigue due to
insufficient contrast.
•
•
The power cable connector is the primary means of detaching
the system from the power supply. The monitor should be
installed close to a power outlet, which is easily accessible.
Cleaning the LCD Panel
•
When the liquid crystal panel is dusty, please gently wipe
with a soft cloth.
Do not move or mount this product by hanging a rope or wire
to the backside handle.
Do not mount or secure this product by using the backside
handle. It may fall and cause personal injury.
•
•
•
Please do not rub the LCD panel with hard material.
Please do not apply pressure to the LCD surface.
Please do not use OA cleaner as it will cause deterioration or
discolor on the LCD surface.
•
•
•
•
•
Handle with care when transporting. Save packaging for
transporting.
Cleaning the Cabinet
If using the cooling fan continuously, it is recommended to
wipe holes clean a minimum of once a month.
•
•
•
Unplug the power supply
Please clean the holes of back cabinet to reject dirt and dust
at least once a year because of set reliability.
Gently wipe the cabinet with a soft cloth
To clean the cabinet, dampen the cloth with a neutral
detergent and water, wipe the cabinet and follow with a dry
cloth.
When using a LAN cable, do not connect to a peripheral
device with wiring that might have excessive voltage.
Do not use monitor under rapid temperature and humidity
change condition or avoid cold air from air-conditioning outlet
directly, as it may shorten the lifetime of the monitor or cause
condensation. If condensation happens, let the monitor stand
unplugged until there is no condensation.
NOTE: DO NOT clean with benzene thinner, alkaline detergent,
alcoholic system detergent, glass cleaner, wax, polish
cleaner, soap powder, or insecticide. Rubber or vinyl
should not be in contact with the cabinet for an extended
period of time. These types of fluids and materials can
cause the paint to deteriorate, crack or peel.
Connecting to a TV*
•
Cable distribution system should be grounded (earthed) in
accordance with ANSI/NFPA 70, the National Electrical Code
(NEC), in particular Section 820.93, Grounding of Outer
Conductive Shield of a Coaxial Cable.
•
The screen of the coaxial cable is intended to be connected
to earth in the building installation.
* The product you purchased may not have this feature.
English-3
Contents
Your new MultiSync monitor box* should contain the following:
•
•
•
•
•
LCD monitor
Power cord*1
•
•
Clamp x 1 (X464UN/X464UNS/X464UNV)/
x 3 (X554UN/X554UNS/X554UNV)
Screw with washer (M4 x 10) x 1 (X464UN/X464UNS/
X464UNV)/x 3 (X554UN/X554UNS/X554UNV)
Thumbscrew for optional stand x 2*2
Video Signal Cable (DisplayPort cable)
LAN cable
•
•
Setup Manual
CD-ROM
Video Signal Cable
(DisplayPort cable)
Power Cord*1
Screw with washer (M4 x 10)
x 1 (X464UN/X464UNS/X464UNV)/
x 3 (X554UN/X554UNS/X554UNV)
Clamp x 1 (X464UN/X464UNS/
X464UNV)/x 3 (X554UN/
X554UNS/X554UNV)
LAN cable
Setup Manual
Thumbscrew for
optional stand x 2*2
CD-ROM
Setup Manual
*
*
Remember to save your original box and packing material to transport or ship the monitor.
1
Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than one
power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been approved by
and complies with the safety standard of your particular country.
2
*
Only for X554UN/X554UNS/X554UNV.
Options:
•
•
•
•
Wall mount
Tabletop Stand
Remote Control Kit (Remote control and sensor)
Over-frame Kit
English-4
Installation
This device cannot be used or installed without the Tabletop
Stand or other mounting accessory for support. For proper
installation it is strongly recommended to use a trained,
NEC authorized service person. Failure to follow NEC
standard mounting procedures could result in damage to the
equipment or injury to the user or installer. Product warranty
does not cover damage caused by improper installation.
Failure to follow these recommendations could result in
voiding the warranty.
Orientation
•
When using the display in the portrait position, the
monitor should be rotated clockwise so that the left side
is moved to the top, right side is moved to the bottom.
This will allow for proper ventilation and will extend the
lifetime of the monitor. Improper ventilation may shorten
the lifetime of the monitor.
Mounting
DO NOT mount the monitor yourself. Please ask dealer.
For proper installation it is strongly recommended to use
a trained, qualified technician. Please inspect the location
where the unit is to be mounted. Mounting on wall or ceiling
is the customer’s responsibility. Not all walls or ceilings are
capable of supporting the weight of the unit. Product warranty
does not cover damage caused by improper installation,
remodelling, or natural disasters. Failure to comply with these
recommendations could result in voiding the warranty.
DO NOT block ventilated openings with mounting
accessories or other accessories.
For NEC Qualified Personnel:
To ensure safe installation, use two or more brackets to
mount the unit. Mount the unit to at least two points on the
installation location.
Mounting location
•
•
•
•
•
•
The ceiling and wall must be strong enough to support the
monitor and mounting accessories.
Please note the following when mounting
on wall or ceiling
DO NOT install in locations where a door or gate can hit
the unit.
•
When using mounting accessories other than those that
are NEC approved, they must comply with the VESA-
compatible (FDMlv1) mounting method.
DO NOT install in areas where the unit will be subjected
to strong vibrations and dust.
DO NOT install near where the main power supply enters
the building.
•
•
NEC recommends mounting interfaces that comply with
UL1678 standard in North America.
Do not install in where people can easily grab and hang
onto the unit or the mounting apparatus.
Mounting
Bracket
X464UN/X464UNS/X464UNV:
NEC strongly recommends
using size M6 screws
Unit
No gap
When mounting in a recessed area, as in a wall, leave at
least 4 inches (100 mm) of space between the monitor
and the wall for proper ventilation.
No thread
4 mm
Washers
(10-12 mm + thickness
under
ꢀ 8.5 mm
Screw
of bracket and washer in
length). If using screws
longer than 10-12 mm,
•
Allow adequate ventilation or provide air conditioning
around the monitor, so that heat can properly dissipate
away from the unit and mounting apparatus.
10-12 mm (X464UN/X464UNS/X464UNV)
10-14 mm (X554UN/X554UNS/X554UNV)
Thickness
of bracket
and washers
check the depth of the hole.
(Recommended Fasten Force:
470 - 635N•cm). Bracket hole should be under ꢀ 8.5 mm.
Mounting on ceiling
•
Ensure that the ceiling is sturdy enough to support the
weight of the unit and the mounting apparatus over time,
against earthquakes, unexpected vibrations, and other
external forces.
•
•
X554UN/X554UNS/X554UNV: NEC strongly recommends
using size M6 screws (10-14 mm + thickness of bracket
and washer in length). If using screws longer than
10-14 mm, check the depth of the hole. (Recommended
Fasten Force: 470 - 635N•cm). Bracket hole should be
under ꢀ 8.5 mm.
•
•
Be sure the unit is mounted to a solid structure within
the ceiling, such as a support beam. Secure the monitor
using bolts, spring lock washers, washer and nut.
Prior to mounting, inspect the installation location to
insure that it is strong enough to support the weight of the
unit so that the unit will be safe from harm.
DO NOT mount to areas that have no supporting internal
structure. DO NOT use wood screws or anchor screws for
mounting. DO NOT mount the unit to trim or to hanging
fixtures.
•
•
•
Refer to the instructions included with the mounting
equipment for detailed information.
Make sure there is no gap between the monitor and the
bracket.
Maintenance
•
Periodically check for loose screws, gaps, distortions,
or other problems that may occur with the mounting
apparatus. If a problem is detected, please refer to
qualified personnel for service.
When used in a video wall configuration for a longer
time, slight expansion of the displays may happen due to
temperature changes. Due to this it is recommended that
over one millimeter gap is kept between adjacent display
edges.
•
Regularly check the mounting location for signs of
damage or weakness that may occur over time.
English-5
3. Installing and removing optional table
top stand
Attaching Mounting Accessories
The monitor is designed for use with the VESA mounting
system.
CAUTION: Installing and removing the stand must be done
by two or more people.
1. Attach Mounting Accessories
To install, follow those instructions included with the stand or
mounting apparatus. Use only those devices recommended
by the manufacturer.
Be careful to avoid tipping monitor when attaching
accessories.
For NEC mounting accessory only*1
VESA Mounting Interface (M6)
NOTE:
For X464UN/X464UNS/X464UNV, use ONLY
thumbscrews which are included with the optional
table top stand.
For X554UN/X554UNS/X554UNV, use ONLY
thumbscrews which are included in the monitor.
When installing the LCD monitor stand, handle the unit with
care to avoid pinching your fingers.
Optional table top stand
300 mm (X464UN/
X464UNS/X464UNV)
400 mm (X554UN/
X554UNS/X554UNV)
Mounting accessories can be attached with the monitor in
the face down position. To avoid damaging the screen face,
place the protective sheet on the table underneath the LCD.
The protective sheet was wrapped around the LCD in the
original packaging. Make sure there is nothing on the table
that can damage the monitor.
Table
Protective Sheet
NOTE:
Install the stand so the long end of the feet
face forward. Use the ST-322 for the X464UN/
X464UNS/X464UNV and the ST-5220 for the
X554UN/X554UNS/X554UNV.
When using mounting accessories other than NEC compliant
and approved, they must comply with the VESA-compatible
mounting method.
4. Ventilation Requirements
When mounting in an enclosed space or recessed area,
leave adequate room between the monitor and the enclosure
to allow heat to disperse, as shown below.
*1: X464UN/X464UNV: WM-46UN-L2 or WM-46UN-P.
X464UNS: WM-46UN-L3 or WM-46UN-P2.
X554UN/X554UNS/X554UNV: WM-55UN-L or WM-55UN-P.
2. Using Option Board
1. Turn off the main power switch.
2. Remove the handle.*2
3. Remove the attached slot cover by unscrewing the
installed screws (Figure 1).
4. Insert option board in to the monitor. Attach the slot cover
by using the removed screws.
5. Attach the handle.*2
NOTE:
Please contact your supplier for available option
boards.
Do not apply excessive force to manipulate the
optional board before fixing it with screws.
Allow adequate ventilation or provide air conditioning around
the monitor, so that heat can properly dissipate away from
the unit and mounting apparatus; especially when you use
monitors in multiple screen.
(Only for X464UN/X464UNS/X464UNV)
Figure 1
*2: Only for X464UN/X464UNS/X464UNV.
English-6
5. Prevent Tipping
X464UNS and X554UNS only:
Installing Optional Sensor Unit
Fixed by screw: Remove the seal, which is pasted on the
bezel you want to set, and then secure the sensor unit using
the attached screw.
When using the display with the optional table top stand
fasten the LCD to a wall using a cord or chain that can
support the weight of the monitor in order to prevent the
monitor from falling. Fasten the cord or chain to the monitor
using the provided clamps and screws.
Fixed by double-sided tape: You can set the sensor unit at
any side of the monitor.
For the X464UN/X464UNS/X464UNV, the clamps and
screws are included with the optional table top stand.
640 mm*
NOTE:
When installing the sensor on the upper and left
sides of the monitor, follow instructions below to
avoid damage to the monitor.
100 mm*1
Screw Holes*1
Screw Holes*
Installing on the upper and left side of the monitor.
Fixed by screw: Set the sensor unit close to the back side.
Fixed by double-sided tape: Set the sensor unit keeping it
8 mm away from the front edge.
Screw Position
Cord or chain
Clamp
Screw (M4)
*: X554UN/X554UNS/X554UNV
*1: X464UN/X464UNS/X464UNV
Before attaching the LCD monitor to the wall, make sure that
the wall can support the weight of the monitor.
Seal
Be sure to remove the cord or chain from the wall before
moving the LCD.
Double-sided tape
8 mm
English-7
Parts Name and Functions
Control Panel
³ POWER button (
)
º EXIT button (EXIT)
Switches the power on/off. See also page 16.
Activates the OSD menu when the OSD menu is turned-off.
Acts as EXIT button within the OSD to move to previous
menu.
· MUTE button (MUTE)
Switches the audio mute ON/OFF.
¾ Remote control sensor and Power Indicator
» INPUT button (INPUT)
Receives the signal from the remote control (when using the
wireless remote control). See also page 11.
Acts as SET/POINT ZOOM button within OSD menu.
(Toggle switches between [DVI], [DPORT], [HDMI], [VGA] or
[Y/Pb/Pr], [SCART]*, [VIDEO]*, [S-VIDEO]*, [HDMI2]*,
[HDMI3]*, [RGB/HV]* or [Y/Pb/Pr2]*). These are available
input only, shown as their factory preset name.
Glows green when the LCD monitor is in active mode*.
Glows red when the LCD is in POWER OFF mode.
Glows amber when the monitor is in Power Save Mode.
Green and Amber blink alternately while in Power Standby
mode with the “SCHEDULE SETTINGS” function enabled.
When a component failure is detected within the monitor, the
indicator will blink red.
¿ PLUS button (+)
Acts as (+) button to increase the adjustment with OSD menu.
Increases the audio output level when the OSD menu is
turned off.
* If “OFF” is selected in “POWER INDICATOR” (see page 25),
LED will not light when the LCD monitor is in active mode.
Control Key Lock Mode
´ MINUS button (-)
Acts as (-) button to decrease the adjustment with OSD menu.
Decreases the audio output level when the OSD menu is
turned off.
This control completely locks out access to all Control Key
functions. To activate the control key lock function, press
both and and hold down simultaneously for more than
3 seconds. To resume user mode, press both and and
hold simultaneously for more than 3 seconds.
² UP button (
Activates the OSD menu when the OSD menu is turned-off.
Acts as button to move the highlighted area up to select
adjustment items within OSD menu.
)
*: This function depends on which option board you use.
¶ DOWN button (
)
Activates the OSD menu when the OSD menu is turned-off.
Acts as button to move the highlighted area down to select
adjustment items within OSD menu.
English-8
Terminal Panel
Option control unit
From Option control unit
³ AC IN connector
¸ DisplayPort connectors
Connects with the supplied power cord.
IN connector: To input DisplayPort signals.
OUT connector: To output signal which is displayed.
See page 25 VIDEO OUT SETTING.
To output signal which is displayed as a main picture when
selected PIP mode. See page 11.
· Main Power Switch
On/Off switch to turn main power ON/OFF.
» EXTERNAL SPEAKER TERMINAL
¹ HDMI IN
To input digital HDMI signals.
To output the audio signal from AUDIO 1, DPORT and HDMI.
Red terminal is plus (+).
Black terminal is minus (-).
NOTE: This speaker terminal is for 15 W + 15 W (8 ohm) speaker.
Ƹ DVI IN (DVI-D)
To input digital RGB signals from a computer or HDTV device
having a digital RGB output.
* This connector does not support analog input.
¿ AUDIO OUT
To output the audio signal from the AUDIO IN 1, 2, DPORT and
HDMI to an external device (stereo receiver, amplifier, etc.).
This connector does not support Headphone terminal.
ƹ Option board slot
Slot 2 and slot 3 type accessories are available.
Please contact your supplier for detailed information.
NOTE: Please contact your supplier for available option board.
´ Service port
This USB slot is for future software upgrades.
ƺ Remote control sensor, AMBIENT LIGHT SENSOR
² LAN port (RJ-45)
LAN connection. See page 32 and 35.
NOTE: Please give priority for use to LAN1.
and HUMAN SENSOR
Receives the signal from the Remote control.
Detects the level of ambient light, allowing the monitor to
make automatic adjustments to the brightness setting,
resulting in a more comfortable viewing experience.
Do not cover this sensor. See page 19.
¶ AUDIO IN 1, 2
To input audio signal from external equipment such as a
computer or DVD player.
Detects human presence in front of the monitor. See page 46.
ᕨ RS-232C (D-Sub 9 pin)
ƻ Kensington Lock
Connect RS-232C input from external equipment such as a PC
in order to control RS-232C functions.
For security and theft prevention.
Ƽ Intelligent wireless data sensor
Sensor for wireless communication of the monitor information
and settings.
¾ REMOTE IN
Use the optional wired remote control by connecting it to your
monitor.
ƽ Rating Label
NOTE: Do not use this connector unless specified.
µVGA IN (mini D-Sub 15 pin)
To input analog RGB signals from a personal computer or
from other RGB equipment. This input can be used with an
RGB or COMPONENT source. Please select signal type in
TERMINAL SETTING. See page 28.
NOTE: When you use this connector for COMPONENT,
please use a suitable signal cable. If you have any questions,
please ask your dealer.
English-9
Wireless Remote Control (Optional)
´ AUDIO INPUT button
Selects audio input source [IN1], [IN2], [IN3]*2, [OPTION]*2,
[HDMI], [DPORT], [HDMI2]*2, [HDMI3]*2.
² OPTION MENU button*1
¶ KEYPAD
Press buttons to set and change passwords, change channel
and set REMOTE ID.
º ENT button*1
¾ DISPLAY button
Turns on/off the information OSD. See page 18.
µ MENU button
Turns on/off the menu mode.
¸ AUTO SET UP button
Enters auto setup menu. See page 20.
¹ EXIT button
Returns to previous menu within OSD menu.
Ƹ UP/DOWN button (
/
)
Acts as button to move the highlighted area up or down
to select adjustment items within OSD menu.
Small screen which adjusted “PIP” mode moves up or down.
ƹ MINUS/PLUS (-/+) button
Increases or decreases the adjustment level within OSD
menu settings.
Small screen which adjusted “PIP” mode moves left or right
and increases or decreases the size.
³ POWER button
Switches the power on/standby.
· INPUT button
ƺ SET/POINT ZOOM button
Selects input signal.
Makes selection. Activates POINT ZOOM function when OSD
menu is not shown.
DVI: DVI
HDMI: HDMI, HDMI2*2, HDMI3*2
DisplayPort: DPORT
ƻVOLUME UP/DOWN button (VOL +/-)
Increases or decreases audio output level.
VGA: VGA
Y/Pb/Pr: Y/Pb/Pr, SCART*2, Y/Pb/Pr2*2
RGB/HV*2: RGB/HV
Ƽ CH/ZOOM UP/DOWN button (CH/ZOOM +/-)*1
Increases or decreases POINT ZOOM level.
VIDEO*2: VIDEO, S-VIDEO
OPTION: Depends on your connection
ƽ GUIDE button*1
» PICTURE MODE button
Selects picture mode, [HIGHBRIGHT], [STANDARD],
[sRGB], [CINEMA], [CUSTOM1], [CUSTOM2]. See page 18.
ƾ MUTE button
Turns on/off mute function.
HIGHBRIGHT: for moving images such as DVD.
STANDARD: for images.
sRGB: for text based images.
CINEMA: for movies.
CUSTOM1 and CUSTOM2: activate auto dimming
function. See page 29.
ƿ STILL button
ON/OFF button: Activates/deactivates still picture mode.
STILL CAPTURE button: Captures still picture.
NOTE: This function is released when activating IMAGE
FLIP.
IMAGE FLIP button
¿ ASPECT button
Toggle switches between H FLIP, V FLIP, 180° ROTATE and
NONE. See page 21.
Selects picture aspect, [FULL], [WIDE], [DYNAMIC], [1:1],
[ZOOM] and [NORMAL]. See page 17.
English-10
PIP (Picture In Picture) button
Operating Range for the Optional
Remote Control
ON/OFF button: Toggle switches between PIP, POP,
PICTURE BY PICTURE-ASPECT and PICTURE BY
PICTURE-FULL. See page 22.
INPUT button: Selects the “picture in picture” input signal.
CHANGE button: Replaces to the main picture and sub
picture.
NOTE: Enable to change the sub picture size by pressing
SET/POINT ZOOM button during PIP mode.
Sub picture
Point the top of the remote control toward the sensor unit’s
remote control sensor in optional control kit during button
operation.
Use the remote control within a distance of about 7 m (23 ft.)
from remote control sensor or at a horizontal and vertical
angle of within 30° within a distance of about 3.5 m (10 ft.).
Main picture Connector
DP Out*5
DPORT*3
DVI
Yes
No
HDMI
Yes
Yes
No
VGA
Yes
Yes
Yes
No
Y/Pb/Pr
Yes
Yes
Yes
No
OPTION
Yes
DPORT
DVI
DisplayPort
DVI-D
No
DPORT
Yes
Yes
DVI
HDMI
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
HDMI
VGA
Yes
Yes
Yes
Yes
Yes
-
D-Sub*4
Y/Pb/Pr
OPTION
Yes
No
No
Yes
-
Option
Yes
Yes
Yes
No
OPTION
*3: When VIDEO OUT SETTING is ONN, DPORT ccannot bbe selectted as thhe sub piicture.
*4: If VGA or Y/Pb/Pr is selected as the main picture, DP out iss disabbled eveen when
VIDEO OUT SETTTING is ON.
*5: DP out can output signal only when VIDEO OUT SETTTING iis ON.
REMOTE ID button
Caution: Important, the remote control
system may not function
Activates REMOTE ID function.
when direct sunlight or strong
illumination strikes the remote
control sensor or when there is
an object in the path.
MTS button*1
button*1
Activates closed captioning.
NOTE: VIDEO*2, S-VIDEO*2 inputs only.
*1: This button’s action depends on which option board you use.
Refer to the option board’s manual for further information.
Handling the remote control
*2: This function depends on which option board you use.
•
•
Do not subject to strong shock.
Do not allow water or other liquid to splash the remote
control. If the remote control gets wet, wipe it dry
immediately.
•
•
Avoid exposure to heat and steam.
Other than to install the batteries, do not open the remote
control.
English-11
Setup
NEC recommends the following battery use:
1. Determine the installation location
CAUTION: Installing your LCD monitor must be done by a
qualified technician. Contact your dealer for more
information.
•
Place “AAA” size batteries matching the (+) and (-) signs
on each battery to the (+) and (-) signs of the battery
compartment.
•
•
Do not mix battery brands.
CAUTION: MOVING OR INSTALLING THE LCD MONITOR
MUST BE DONE BY TWO OR MORE PEOPLE.
Failure to follow this caution may result in injury if
the LCD monitor falls.
Do not combine new and old batteries. This can shorten
battery life or cause liquid leakage of batteries.
•
Remove dead batteries immediately to prevent battery
acid from leaking into the battery compartment.
CAUTION: Do not mount or operate the monitor upside
•
Do not touch exposed battery acid, it may injure skin.
down, face up or face down.
NOTE:
If you do not intend to use the Remote Control for
a long period of time, remove the batteries.
CAUTION: This LCD has a temperature sensor and cooling
fan, including a fan for the option board.
If the LCD becomes too hot, the cooling fan will
turn on automatically.
3. Connect external equipment
(See pages 14 and 15)
The option board’s fan is active although the
temperature is lower than normal operating
temperature for cooling the option board. If the
LCD becomes overheated while the cooling fan
is running, a “Caution” warning will appear. If the
“Caution” warning appears, discontinue use and
allow the unit to cool. Using the cooling fan will
reduce the likelihood of early circuit failure and
may help reduce image degradation and “Image
Persistance”.
If the LCD is used in an enclosed area or if the
LCD panel is covered with a protective screen,
please check the inside temperature of the
monitor by using the “HEAT STATUS” control
in the OSD (see page 26). If the temperature is
higher than the normal operating temperature,
please turn the cooling fan to ON within the FAN
CONTROL menu within the OSD (see page 26).
•
To protect the external equipment; turn off the main power
before making connections.
•
Refer to your equipment user manual for further
information.
NOTE:
Do not connect/disconnect cables when turning
on the monitor or other external equipment as this
may result in a loss of the monitor image.
4. Connect the supplied power cord
•
•
•
The equipment should be installed close to an easily
accessible power outlet.
Please fasten power cord to the LCD monitor by attaching
the screw and clamp.
Fully insert the prongs into the power outlet socket.
A loose connection may cause image degradation.
NOTE:
Please refer to the “Safety Precautions and
Maintenance” section of this manual for proper
selection of AC power cord.
IMPORTANT: Lay the protective sheet, which was wrapped
around the LCD monitor when it was
packaged, beneath the LCD monitor so as not
to scratch the panel.
2. Install the remote control (Optional)
batteries
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
Screw
Clamp
A. Press and slide to open the cover.
B. Align the batteries according to the (+) and (–) indications
inside the case.
C. Replace the cover.
CAUTION: Incorrect usage of batteries can result in leaks or
bursting.
English-12
5. Switch on the power of all the attached
external equipment
When connected with a computer, switch on the power of the
computer first.
6. Operate the attached external equipment
Display the signal from the desired input source.
7. Adjust the sound
Make volume adjustments when required.
8. Adjust the screen (See pages 20 and 21)
Make adjustments of the screen display position when
necessary.
9. Adjust the image (See page 20)
Make adjustments such as backlight or contrast when
required.
10. Recommended Adjustments
To reduce the risk of the “Image Persistence”, please adjust
the following items based on the application being used:
“SCREEN SAVER”, “SIDE BORDER COLOR” (See page 26)
“DATE & TIME”, “SCHEDULE SETTINGS” (See page 22).
It is recommended that the “FAN CONTROL” setting
(See page 26) be turned to ON also.
English-13
Connections
NOTE:
Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a
loss of the monitor image.
NOTE:
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.
Before making connections:
*
*
First turn off the power of all the attached equipment and make connections.
Refer to the user manual included with each separate piece of equipment.
Wiring Diagram
DVD Player
Second monitor*
Solid lines = video signal
Dotted lines = audio signal
Stereo Amplifier
Computer (Analog)
*: Multiple monitors that are daisy-chained have a limit to the connectable monitors.
Computer (Digital)
Connected
equipment
Connecting
terminal
DisplayPort
DVI (DVI-D)
HDMI
VGA (D-Sub)
VGA (D-Sub)
Option
DisplayPort
DVI (DVI-D)
HDMI
Connecting
audio terminal
DPORT
AUDIO IN1/IN2
HDMI
AUDIO IN1/IN2
AUDIO IN1/IN2
OPTION
DPORT
AUDIO IN1/IN2
HDMI
Input button
Setting in terminal mode
Input signal name
in remote control
DisplayPort
DVI
RAW/EXPAND*1
DVI-HD
DP
DVI
HDMI
RAW/EXPAND*1
D-SUB MODE RGB
D-SUB MODE COMPONENT
RAW/EXPAND*1
RAW/EXPAND*1
DVI-PC
HDMI
RGB/HV
Y/Pb/Pr
OPTION
DisplayPort
DVI
HDMI
RGB/HV
OPTION
AV
VGA
COMPONENT
OPTION
DP
DVI
HDMI
VGA
OPTION
PC
RAW/EXPAND*1
-
VGA (D-Sub)
Option
AUDIO IN1/IN2
OPTION
RAW/EXPAND*1
*1: depend on signal type.
English-14
Connecting a Personal Computer
Connecting your computer to your LCD monitor will enable you to display your computer’s screen image.
Some display cards may not display an image correctly.
Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically.
<Typical factory preset signal timing>
Scanning frequency
Horizontal Vertical
Remarks
Resolution
640 x 480
800 x 600
31.5 kHz
37.9 kHz
48.4 kHz
48 kHz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
1024 x 768
1280 x 768
1360 x 768
1280 x 1024
1600 x 1200
1920 x 1080
48 kHz
64 kHz
75 kHz
Compressed image
67.5 kHz
Recommended resolution
•
If you use with a Macintosh PowerBook, set “Mirroring” to Off on your PowerBook.
Refer to your Macintosh’s owner’s manual for more information about your computer’s video output requirements and any
special identification or configuration your monitor’s image and monitor may require.
•
•
Input TMDS signals conforming to DVI standards.
To maintain display quality, use a cable that conforms to DVI standards.
Connecting a DVD Player or Computer with HDMI out
•
•
•
•
Please use an HDMI cable with HDMI logo.
It may take a moment for the signal to appear.
Some display cards or drivers may not display an image correctly.
When you use a computer with HDMI out, please set OVER SCAN to “OFF” (see page 28).
Connecting a Computer with DisplayPort
•
•
•
Please use DisplayPort cable with DisplayPort compliance logo.
It may take a moment for the signal to appear.
Please note that when connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not
appear.
•
Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.
English-15
Basic Operation
Power ON and OFF Modes
The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off.
NOTE:
The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the
Power Button.
OFF
Main Power Switch
ON
Power Button
Using the optional remote control
English-16
Power Indicator
Picture Aspect
DVI, VGA, RGV/HV*4, DPORT
Mode
Status Indicator Light
Green*1
FULL
1:1
ZOOM
NORMAL
Power ON
Power OFF and Power Save “AUTO Red
STANDBY”
Power consumption under 0.5 W*2
Power Save “AUTO POWER SAVE” Amber
Power consumption under 2.5 W
HDMI, Y/Pb/Pr, SCART*4, VIDEO*4, S-VIDEO*4, HDMI2*4, HDMI3*4,
Y/Pb/Pr2*4
FULL
WIDE
DYNAMIC
1:1
ZOOM
NORMAL
Power Standby when “SCHEDULE
SETTINGS” enabled
Diagnosis (Detecting failure)
Green and Amber blink alternately
Aspect ratio
of image
Recommended selection
for picture aspect*3
Unchanged view*3
Red Blinking
(See Troubleshooting page 47)
NORMAL
*1 If “OFF” is selected in POWER INDICATOR (page 25), the LED will not light when the
LCD monitor is in active mode.
*2 Without any option, with factory settings.
4:3
DYNAMIC
FULL
Initial settings
Setting LAN POWER (see page 27) and POWER SAVE
(see page 26) windows appear on first time the power is on.
These settings are only necessary upon initial setup.
However, these message window appears when the power is
on after FACTORY RESET is done.
Squeeze
Letterbox
When LAN POWER is set to ON and POWER SAVE is set to
“DISABLE” after FACTORY RESET, then the monitor power
is off and on again, the message window will not appear.
WIDE
Using Power Management
*3 Grey areas indicate unused portions of the screen.
The LCD monitor follows the VESA approved DPM Display
Power Management function.
NORMAL: Displays the aspect ratio the same as it is sent
The power management function is an energy saving
function that automatically reduces the power consumption
of the display when the keyboard or the mouse has not been
used for a fixed period.
The power management feature on your new display has
been set to the “AUTO STANDBY” mode. This allows your
display to enter a Power Saving Mode when no signal is
applied. This could potentially increase the life and decrease
the power consumption of the display.
from the source.
FULL: Fills entire screen.
WIDE: Expands a 16:9 letter box signal to fill entire screen.
DYNAMIC: Expands a 4:3 pictures to fill the entire screen
with non-linearity. Some of the outside image area will be cut
off due to expansion.
1:1: Displays the image in a 1 by 1 pixel format.
NOTE:
Depending on the PC and Display card used, this
function may not operate.
ZOOM
The image can be expanded beyond the active display area.
The image which is outside of active display area is not
shown.
NOTE:
The monitor automatically goes into OFF at the
preset time period after signal is lost.
ZOOM
Selecting a video source*4
To view a video source:
Use the input button to set [VIDEO], [S-VIDEO].
ZOOM
Use the COLOR SYSTEM menu to set [AUTO], [NTSC],
[PAL], [SECAM], [PAL60], [4.43NTSC], according to your
video format.
*4: This function depends on which option board you use.
English-17
Information OSD
The Information OSD provides information such as: Input Source, Picture Size, etc.
Press the DISPLAY button on the remote to bring up the Information OSD.
³
·
»
¿
ᕥ
Input Name
Audio input mode
Picture aspect
Input Signal Information
Sub picture information
Picture Mode
DVI, VGA, RGB/HV*, DPORT
STANDARD
sRGB
CUSTOM1
CUSTOM2
HIGHBRIGHT
HDMI, Y/Pb/Pr, SCART*, VIDEO*, S-VIDEO*, HDMI2*, HDMI3*, Y/Pb/Pr2*
STANDARD
CINEMA
CUSTOM1
CUSTOM2
HIGHBRIGHT
*: This function depends on which option board you use.
English-18
OSD (On-Screen-Display) Controls
NOTE:
Some functions may not be available depending on the model or optional equipment.
Input source
Main Menu Icons
Main Menu Item
70
50
50
50
Adjustment Settings
50
Sub Menu
50
THANK YOU FOR SAVING
THE ENVIRONMENT.
CARBON FOOTPRINT
86.0 %
PICTURE MODE
Goto Adjustment Return
Close
Select
Key Guide
Press UP or DOWN
button to select
sub-menu.
Press SET/POINT
ZOOM.
Press UP or DOWN,
PLUS or MINUS to select
the function or setting to
be adjusted.
Press MENU or EXIT.
Remote Control
Press UP or DOWN
button to select.
Press INPUT button
to decide.
Press UP or DOWN, PLUS
or MINUS button to select.
Press EXIT
Control Panel
OSD screen
English-19
Setting
Default
PICTURE
BACKLIGHT
Adjusts the overall image and background brightness. Press + or - to adjust.
NOTE: When MODE1 or MODE2 is selected in ROOM LIGHT SENSING, this function cannot be
changed.
Depends on
destination
CONTRAST
Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
50
SHARPNESS
BRIGHTNESS
Adjusts the crispness of the image. Press + or - to adjust.
50*2
50
Adjusts the image brightness in relationship to the background. Press + or - to adjust.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
HUE
Adjusts the hue of the screen. Press + or - to adjust.
50
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
COLOR
Adjusts the color depth of the screen. Press + or - to adjust.
50*2
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
COLOR TEMPERATURE
Adjusts the color temperature of the entire screen. A low color temperature will make the screen
reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further
adjustment, the individual R/G/B/ levels of the white point can be adjusted. To adjust the R/G/B
levels, CUSTOM must be showing as the COLOR TEMP selection.
10000K
NOTE: When sRGB is selected in picture mode, predefined 6500k is set so it cannot be changed.
When PROGRAMMABLE1, PROGRAMMABLE2 or PROGRAMMABLE3 is selected in GAMMA
CORRECTION, this function cannot be changed.
COLOR CONTROL
Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
When INPUT2 of SUPER is selected in INPUT CHANGE and displayed, this function cannot be
changed.
0
GAMMA CORRECTION
Select a display gamma for best picture quality.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
PROGRAMMABLE1
(except sRGB
setting)
NATIVE
2.2
Gamma correction is handled by the LCD panel.
Typical display gamma for use with a PC.
Good for video (DVD, etc.)
2.4
S GAMMA
Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the
image (S-Curve).
DICOM SIM.
DICOM GSDF curve simulated for LCD type.
PROGRAMMABLE1, 2, 3 A programmable gamma curve can be loaded using NEC optional software.
MOVIE SETTINGS
NOTE: When INPUT2 of SUPER is selected in INPUT CHANGE and displayed, this function
cannot be changed.
NOISE REDUCTION*1 Adjusts the amount of noise reduction. Press + or - to adjust.
0*2
SCART, VIDEO, S-VIDEO inputs only
TELECINE
Automatically senses the sources frame rate for optimal picture quality.
AUTO*2
HDMI, Y/Pb/Pr, SCART*1, VIDEO*1, S-VIDEO*1,
HDMI2*1, HDMI3*1, Y/Pb/Pr2*1 inputs only
ADAPTIVE CONTRAST Sets the level of adjustment for dynamic contrast.
HDMI, Y/Pb/Pr, SCART*1, VIDEO*1, S-VIDEO*1,
OFF
HDMI2*1, HDMI3*1, Y/Pb/Pr2*1 inputs only
PICTURE MODE
RESET
Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [CUSTOM1] or
[CUSTOM2]. See page 18.
STANDARD
-
Resets the following settings within the PICTURE menu back to factory setting: BACKLIGHT,
CONTRAST, SHARPNESS, BRIGHTNESS, HUE, COLOR, COLOR TEMPERATURE,
COLOR CONTROL, GAMMA CORRECTION, MOVIE SETTINGS.
ADJUST
AUTO SETUP
Automatically adjusts Screen Size, H position, V position, Clock, Phase and White Level.
H Position, V Position and Phase are adjusted automatically when new timing is detected.
-
OFF
-
VGA, RGB/HV*1 inputs only
AUTO ADJUST
VGA, RGB/HV*1 inputs only
H POSITION
Controls the horizontal position of the image within the Display area of the LCD.
Press + to move right. Press - to move left.
All inputs except DVI, HDMI, DPORT
V POSITION
Controls the vertical position of the image within the Display area of the LCD.
Press + to move up. Press - to move down.
-
-
All inputs except DVI, HDMI, DPORT
CLOCK
Press + to expand the width of the image on the right of the screen.
Press - to narrow the width of the image on the left.
VGA, RGB/HV*1 inputs only
*1: This function depends on which option board you use.
*2: Depends on signal input.
English-20
PHASE
Adjusts the visual “noise” on the image.
-
VGA, RGB/HV*1, Y/Pb/Pr, SCART*1, Y/Pb/Pr2*1
inputs only
H RESOLUTION
Adjusts the horizontal size of the image.
Adjusts the vertical size of the image.
-
-
VGA, RGB/HV*1 inputs only
V RESOLUTION
VGA, RGB/HV*1 inputs only
INPUT RESOLUTION
If there is a problem with signal detection, this function forces the monitor to display the signal at
the desired resolution. After selection, execute “AUTO SETUP” if required.
If no problem is detected, the only available option will be “AUTO”.
AUTO
VGA, RGB/HV*1 inputs only
ASPECT
Select the aspect ratio of the screen image.
FULL
NOTE: When the ASPECT is DYNAMIC, WIDE or ZOOM, the image will be changed FULL
image before IMAGE FLIP, then start to IMAGE FLIP.
When the ASPECT is DYNAMIC or ZOOM, the image will be changed FULL image before TILE
MATRIX, then start to TILE MATRIX. After TILE MATRIX, the ASPECT will be returned previous
ASPECT or set ASPECT during TILE MATRIX.
When the ASPECT is DYNAMIC or ZOOM, the image will be changed FULL image before POINT
ZOOM, then start to POINT ZOOM. After POINT ZOOM, the ASPECT will be returned previous
ASPECT. When the ASPECT is changed during POINT ZOOM, DYNAMIC and ZOOM will be
FULL image.
NORMAL
FULL
Displays the aspect ratio the same as it is sent from the source.
Fills entire screen.
-
-
-
-
WIDE
Expands a 16:9 letter box signal to fill entire screen.
DYNAMIC
Expands a 4:3 pictures to fill the entire screen with non-linearity. Some of the outside image area
will be cut off due to expansion. TILE MATRIX becomes invalid.
1:1
Display the image in a 1 by 1 pixel format. (If the input resolution is higher than a 1920 x 1080
resolution, the image will be scaled down to fit the screen). TILE MATRIX becomes invalid.
-
-
ZOOM
The image can be expanded/reduced.
NOTE: The expanded image which is outside of active display area is not shown. The reduced
image may have some image degradation.
ZOOM
HZOOM
Maintains the aspect ratio while zooming.
Amount of horizontal zoom.
Amount of vertical zoom.
Horizontal position.
-
VZOOM
H POS
V POS
Vertical position.
IMAGE FLIP
NOTE: OVER SCAN is disabled when IMAGE FLIP is selected.
-
When the ASPECT is DYNAMIC, WIDE or ZOOM, the image will be changed FULL image before
IMAGE FLIP, then start to IMAGE FLIP.
When selecting IMAGE FLIP except for NONE, following functions are released: PIP MODE,
TILE MATRIX, SUPER in INPUT CHANGE, STILL, POINT ZOOM.
IMAGE FLIP
Display the inverse image right-left, up-down or rotation.
Press + or - to select.
NONE
NONE
H FLIP
-
Normal mode.
-
The image inverts right-left.
The image inverts up-down.
The image rotates 180 degrees.
V FLIP
-
-
180° ROTATE
OSD FLIP
Determines the OSD display direction.
OFF
If “ON” is selected, OSD will invert depending on the image.
RESET
Resets “ADJUST” settings back to factory settings.
-
AUDIO
VOLUME
BALANCE
Increases or decreases output volume level.
40
Select “STEREO” or “MONO” of audio output.
CENTER,
STEREO
If you select “STEREO”, adjust the balance of L/R volume.
Press + button to move the stereo sound image to right.
Press - button to move the stereo sound image to left.
TREBLE
To accentuate or reduce the high frequency sound.
Press + button to increase TREBLE sound.
Press - button to decrease TREBLE sound.
0
*1: This function depends on which option board you use.
English-21
BASS
To accentuate or reduce the low frequency sound.
Press + button to increase BASS sound.
Press - button to decrease BASS sound.
0
SURROUND
Artificial surround sound.
OFF
NOTE: Audio out is disabled when this function is set to ON.
PIP AUDIO
LINE OUT
Selects source of PIP audio.
MAIN AUDIO
FIXED
Selecting “VARIABLE” enables control of the line out level with the VOLUME button.
NOTE: Audio out is disabled when this function is set to ON.
AUDIO INPUT
AUDIO DELAY
RESET
Selects audio input source [IN1], [IN2], [IN3]*1, [OPTION]*1, [HDMI], [DPORT], [HDMI2]*1,
[HDMI3]*1.
Depends on
signal input
Enables to set the delay time to output the audio. DELAY TIME can be set between 0 and
100 milliseconds. “ON” activates this function.
ON,
37 MSEC.
Resets “AUDIO” options back to factory settings except VOLUME.
-
SCHEDULE
OFF TIMER
Sets the monitor to power off after a length of time.
A time between 1 to 24 hours is available.
OFF
SCHEDULE SETTINGS
SCHEDULE LIST
DATE & TIME
Creates a working schedule for the monitor to use.
List of schedules.
-
-
Sets the date, time, and daylight saving region. Date & time must be set in order for the
“SCHEDULE” function to operate. See page 30.
YEAR
MONTH
Configures the year for the real-time clock.
Configures the month for the real-time clock.
Configures the day for the real-time clock.
Configures the time for the real-time clock.
Configures daylight savings on or off.
-
-
DAY
-
TIME
-
OFF
-
DAYLIGHT SAVING
RESET
Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER,
SCHEDULE SETTINGS.
PIP
KEEP PIP MODE
Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off.
When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.
OFF
OFF
PIP MODE
Selects Picture-in-Picture mode.
NOTE: This function is released when selecting IMAGE FLIP except for NONE.
OFF
PIP
Normal mode.
Picture in Picture mode.
Picture out Picture mode.
POP
PICTURE BY PICTURE- Picture by picture (split screen) mode, with keep aspect.
ASPECT
PICTURE BY PICTURE
FULL
-
Picture by picture (split screen) mode, with full screen.
SUB INPUT
Selects sub picture input signal.
Depends on
signal input
PIP SIZE
Determines the size of the sub-picture used in Picture-in-Picture (PIP) mode.
Press the SET/POINT ZOOM button to adjust. Press + or CH+ to expand. Press - or CH- to
reduce.
37
It is also possible to change the sub-picture size by pressing the SET/POINT ZOOM button when
the sub-picture is shown.
PIP POSITION
ASPECT
Determines the location where the PIP appears on the screen.
X = 95, Y = 92
FULL
Selects sub picture aspect, [FULL], [NORMAL] and [WIDE]. See page 17.
*1: This function depends on which option board you use.
English-22
TEXT TICKER
MODE
OFF
Enables Text Ticker and allows you to set Horizontal or Vertical direction.
Selects the location of the Text Ticker on the screen.
POSITION
SIZE
Determines the size of the Text Ticker in relationship to the overall screen size.
Sets the transparency of the Text Ticker (0: transparent, 100: opaque).
Enables auto-detection of the Text Ticker.
BLEND
DETECT
FADE IN
RESET
Enables fade-in of the text ticker.
Resets PIP options back to factory settings except SUB INPUT and ASPECT.
-
OSD
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
SVENSKA
РУССКИЙ
Select the language used by the OSD.
ENGLISH
(Depends on
destination)
MENU DISPLAY TIME
OSD POSITION
UP
Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.
Determines the location where the OSD appears on the screen.
30 SEC.
X = 128, Y = 225
DOWN
RIGHT
LEFT
INFORMATION OSD
Selects whether the information OSD is displayed or not. The information OSD will be displayed
when the input signal or source changes. The information OSD will also give a warning when
there is no-signal or the signal is out-of range.
ON, 3 SEC.
An interval between 3 to 10 seconds for the Information OSD to appear is available.
MONITOR INFORMATION Indicates the model and serial number of your monitor and firmware version.
CARBON SAVINGS: Display the estimated carbon saving information in kg-CO2. The carbon
footprint factor in the carbon saving calculation is based on the OECD (2008 Edition).
CARBON USAGE: Display the estimated carbon usage information in kg-CO2. This is the
arithmetic estimation, not actual measurement value. This estimation is based without any
options.
-
OSD TRANSPARENCY
OSD ROTATION
LANDSCAPE
Set the transparency of the OSD.
OFF
Determines the OSD display direction between landscape and portrait.
Display the OSD with landscape mode.
LANDSCAPE
PORTRAIT
Display the OSD with portrait mode.
INPUT NAME
You can create a name for the INPUT currently being used.
-
Max: 8 characters, including Space, A-Z, 0-9, and some symbols.
MEMO
RESET
Sets a title and message via HTTP server. See page 43.
-
-
Resets the following settings within the OSD menu back to factory setting:
MENU DISPLAY TIME, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY.
English-23
MULTI DISPLAY
ID CONTROL
Sets the monitor ID number from 1-100 and group ID from A-J. DETECTED MONITORS shows
the number of all monitors which follow in the chain with LAN.
1
NOTE: Group ID is made of multiple selections.
AUTO ID/IP SETTING
SETTING ITEM
When “YES” is selected, AUTO ID/IP SETTING window is shown.
Do not connect network devices between the monitors connected with LAN.
NO
Select an item from [MONITOR ID], [IP ADDRESS] and [ID and IP].
When “YES” is set, selected item at SETTING ITEM is set.
ID/IP SETTING
START
MONITOR ID
IP ADDRESS
When “YES” is set, monitor ID numbers are set automatically to the all monitors.
Set the first octet to the third octet at “BASE ADDRESS”.
The fourth octet is automatically set from “1” and counting up till the number of monitors
connected with LAN.
“BASE ADDRESS” is shown when “IP ADDRESS” or “ID and IP” is selected at SETTING ITEM.
ID and IP
Set “MONITOR ID” and “IP ADDRESS”.
DETECTED
MONITORS
This item is shown after “SETTING ITEM” is selected and “ID/IP ADDRESS START” is set to
“YES”.
The number of monitors which MONITOR ID is given is shown.
If the shown number and actual monitor number which MONITOR ID is given are different, select
“RETRY” to recount monitors.
Select “OK” when “FINISH!!” is displayed. If “OK” is not selected after “FINISH!!” is displayed, the
settings that have been made will be invalid and will not be reflected.
AUTO ID/IP RESET
RESET ITEM
When “RESET” is selected, AUTO ID/IP RESET window is shown.
Select a setting from [MONITOR ID], [IP ADDRESS], and [ID and IP].
NO
ID/IP RESET START When “YES” is set, the setting of selected item at RESET ITEM returns to default setting.
When the setting returns to default setting, “FINISH!!” is displayed.
After “AUTO ID/IP RESET START” is activated, “MONITOR ID” and “IP ADDRESS” settings will
be individual settings even though monitors are connected with LAN.
NOTE: “AUTO ID RESET” should be done when changes the number of monitors which follow in
the chain with LAN.
COMMAND
TRANSFER
When “YES” is set, command is sent to all the monitors which follow in the chain with LAN.
NOTE: The all monitors connected with LAN should be “ON”. When executing this function in
standby mode or power save mode, “LAN POWER” should be “ON”.
Do not turn off the monitors while AUTO ID/IP SETTING or AUTO ID/IP RESET is activating.
IR LOCK SETTINGS
Prevents the monitor from being controlled by the wireless remote control.
When ACTIVATE is selected, all the settings are activated.
UNLOCK
NOTE: IR LOCK SETTINGS is a function intended only to the wireless remote control buttons.
This function does not lock out access to all buttons at the back of the monitor. To return to
normal operation, press the “DISPLAY” button on the remote control for 5 seconds.
MODE SELECT
UNLOCK
Selects the mode UNLOCK, ALL LOCK or CUSTOM LOCK.
All buttons on the remote control are available for normal operations.
Locks all remote control buttons.
ALL LOCK
CUSTOM LOCK
Selects which buttons to be locked from POWER, VOLUME, and INPUT button.
Except for CUSTOM LOCK settings, other buttons on the remote control are locked.
POWER: When LOCK is selected, POWER button is locked.
VOLUME: When UNLOCK is selected, sets minimum and maximum volume between VOL.0 to
VOL.100.
VOLUME (+) button and VOLUME (-) buttons are only available from the minimum
volume to the maximum volume you set.
When LOCK is selected, VOLUME (+) button and VOLUME (-) buttons are locked.
INPUT:
When UNLOCK is selected, choose up to three buttons from DVI, DisplayPort, VGA,
HDMI, Y/Pb/Pr, VIDEO*1, S-VIDEO*1, OPTION*1 which you prefer to be unlocked.
The unselected buttons are locked. When LOCK is selected, all INPUT buttons are
locked.
*1: This function depends on which option board you use.
English-24
TILE MATRIX
Allows one image to be expanded and displayed over multiple screens (up to 100) through a
distribution amplifier.
NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate
without a distribution amplifier at a lower number of screens.
This function is released when selecting IMAGE FLIP except for NONE.
Dynamic or Zoom will not work when Tile Matrix is activated.
When “DYNAMIC” or “ZOOM” is selected in ASPECT while executing TILE MATRIX, the setting
will be applied after completing of TILE MATRIX.
H MONITORS
V MONITORS
POSITION
Number of monitors arranged horizontally.
Number of monitors arranged vertically.
1
1
Select which section of the tiled image to be displayed on the monitor.
Turns the TILE COMP feature on.
1
TILE COMP
NO
NO
NONE
TILE MATRIX ENABLE Enables Tile Matrix.
FRAME COMP
Sets the tiled image timing to be displayed on the monitor. Large number makes large influence
to displayed image.
NOTE: If FRAME COMP is set to AUTO or MANUAL, V SCAN REVERSE is not available.
The image may be distorted when turning the power on or changing the settings.
NONE
FRAME COMP is not available.
AUTO
Sets display timing to vertical direction of all monitors automatically.
Sets display timing to individual monitor.
MANUAL
V SCAN REVERSE*1
Reverse scanning image direction. Normal scanning direction is top to bottom.
NONE
NOTE: If V SCAN REVERSE is set to AUTO or MANUAL, FRAME COMP is not available.
NONE
AUTO
V SCAN REVERSE is not available.
Sets automatically calculated image scanning direction to all monitors.
Sets scanning direction to individual monitor.
MANUAL
NON REVERSE
REVERSE
Sets normal scanning direction and delays 1 frame display image timing.
Reverse scanning direction to individual monitor.
TILE MATRIX MEM
When “INPUT” is selected, TILE MATRIX setting is applied to each signal input.
COMMON
AUTO TILE MATRIX
SETUP
Allows auto setting of multiple screens by inputting the number of monitors arranged horizontally DEACTIVATE
and vertically on the primary monitor. Following settings are set automatically: MONITOR
ID, TILE MATRIX, TILE MATRIX MEM, Input Signal, VIDEO OUT SETTING, DisplayPort in
TERMINAL SETTING.
NOTE: All monitors which follow in the chain with LAN should be ON. When executing this
function while in standby mode or power save mode, “LAN POWER” should be set to ON.
AUTO ID will be automatically executed. When you use this function, it is recommended that
monitors are chained by DisplayPort cable.
Example of installation via LAN:
Primary monitor
H MONITORS
V MONITORS
3
3
POWER ON DELAY
DELAY TIME
Adjusts the delay time between being in “standby” mode and entering “power on” mode.
“POWER ON DELAY” can be set between 0 and 50 seconds.
0 SEC.
OFF
LINK TO ID
When “ON” selected, delay time is linked with Monitor ID. It takes more time as larger ID number.
VIDEO OUT SETTING
Enables the signal output from DPORT. See also page 28 “DisplayPort” in TERMINAL SETTING.
NOTE: When VGA or Y/Pb/Pr is selected as the main picture, nothing will be output from DPORT.
When this function is ON, DPORT cannot be selected as the sub picture. When this function is
ON, INPUT CHANGE is limited to be NORMAL or QUICK. When this function is ON and DPORT
is selected as the main picture, PIP CHANGE button of remote control (see page 11) is disabled.
ON
POWER INDICATOR
Turns ON or OFF the LED located at the back of the monitor.
ON
If “OFF” is selected, LED will not light when the LCD monitor is in active mode.
*1: Except for X464UNS/X554UNS/X554UNV.
English-25
SETTING COPY
In a daisy chain scenario, select the OSD menu categories that you want to copy over to the
other monitor.
NO
NOTE: When you use this function, monitors should be daisy chained by LAN. This function
resets to default when power is off. This function has a limit depending on the cable you use.
COPY START
ALL INPUT
RESET
Select “YES” and press the SET button to start copying.
All input terminals settings are copied when you select this item. Default is off.
Resets “MULTI DISPLAY” options back to factory settings except for POWER ON DELAY and
VIDEO OUT SETTING.
-
DISPLAY PROTECTION
POWER SAVE
Sets how long the monitor waits to go into power save mode after the signal is lost.
AUTO
NOTE: When connecting DVI, the display card might not stop sending the digital data even
though the image might have disappeared. If this occurs the monitor will not switch into power
management mode. POWER SAVE is disabled when AUTO OFF or CUSTOM is selected in
HUMAN SENSING.
STANDBY
AUTO POWER SAVE
AUTO STANDBY
The monitor automatically goes into OFF at the preset time period after signal is lost.
The monitor will return to normal mode when signal is restarted.
-
-
The monitor automatically goes into OFF at the preset time period after signal is lost.
Press the power button to return to normal mode.
DISABLE
The monitor will not goes into OFF after signal is lost.
-
HEAT STATUS
FAN CONTROL
Displays status of the FAN, BACKLIGHT and TEMPERATURE.
-
Cooling fan reduces the temperature of the display to protect from overheating.
AUTO, HIGH
If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.
SCREEN SAVER
GAMMA
Use the SCREEN SAVER function to reduce the risk of Image Persistence.
The display gamma is changed and fixed when “ON” is selected.
OFF
OFF
BACKLIGHT
The brightness of backlight is decreased when “ON” is selected.
NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.
MOTION
The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at
user determined intervals. You can set interval time and zooming ratio.
This function is disabled when PIP, STILL, TEXT TICKER or TILE MATRIX are enabled.
OFF
15
SIDE BORDER COLOR
Adjusts the color of the side borders when a 4:3 image is displayed.
Press + button, the bar will become lighter.
Press - button, the bar will become darker.
CHANGE PASSWORD
SECURITY
Allows the security password to be changed.
The factory preset password is 0000.
-
Locks the security password.
OFF
START-UP LOCK: Security password is required when the monitor power is on.
CONTROL LOCK: Security password is required when the remote control button or control button
on the monitor is pressed.
BOTH LOCK: Security password is required when the monitor power is on, or the remote control
button or control button on the monitor is pressed.
RESET
Resets the following settings within the DISPLAY PROTECTION menu back to factory setting:
POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR.
-
EXTERNAL CONTROL
IP ADDRESS SETTING
NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN
SETTING is applied.
IP SETTING
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from
your network administrator.
AUTO
NOTE: Consult your network administrator for the IP address when “AUTO” is selected for
[IP SETTING].
IP ADDRESS
Set your IP address of the network connected to the monitor when “MANUAL” is selected for
[IP SETTING].
192.168.0.10
255.255.255.0
0.0.0.0
SUBNET MASK
DEFAULT GATEWAY
Set your subnet mask number of the network connected to the monitor when “MANUAL” is
selected for [IP SETTING].
Set your default gateway of the network connected to the monitor when “MANUAL” is selected
for [IP SETTING].
NOTE: Set as [0.0.0.0] to delete the setting.
English-26
DNS
Set for IP ADDRESS setting of DNS server.
AUTO
AUTO: Automatically assign an IP address of DNS server connected to the monitor.
MANUAL: Set your IP address of DNS server connected to the monitor.
DNS PRIMARY
Set your primary DNS settings of the network connected to the monitor.
NOTE: Set as [0.0.0.0] to delete the setting.
0.0.0.0
0.0.0.0
DNS SECONDARY
Set your secondary DNS settings of the network connected to the monitor.
NOTE: Set as [0.0.0.0] to delete the setting.
MAC ADDRESS
LAN POWER
Displays the MAC ADDRESS.
-
Selects LAN operation mode. When “ON” selected, allows to supply power to LAN during power
save mode or standby mode.
OFF
NOTE: For enabling “AUTO ID” or “AUTO TILE MATRIX SETUP”, this function should be ON.
DDC/CI
PING
ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor.
Confirm the response by communicating to the preset IP address.
ENABLE
192.168.0.10
NO
IP ADDRESS RESET
RESET
Resets IP ADDRESS SETTING back to factory settings.
NO
-
Resets the following setting within the EXTERNAL CONTROL menu back to factory settings:
DDC/CI.
ADVANCED OPTION1
INPUT DETECT
Selects the method of input detection the monitor uses when more than two input devices are
connected.
NONE
NOTE: When SUPER is selected in INPUT CHANGE, this function cannot be changed.
NONE
The Monitor will not search the other video input ports.
FIRST DETECT*2
When the current video input signal is not present, then the monitor searches for a video signal
from the other video input port. If the video signal is present in the other port, then the monitor
switches the video source input port to the new found video source automatically.
The monitor will not look for other video signals while the current video source is present.
LAST DETECT*2
When the monitor is displaying a signal from the current source and a new secondary source
is supplied to the monitor, the monitor will automatically switch to the new video source. When
current video input signal is not present, the monitor searches for a video signal from the other
video input port. If the video signal is present in the other port, then the monitor switches the
video source input port to the new found video source automatically.
VIDEO DETECT
Y/Pb/Pr, Y/Pb/Pr2*1, SCART*1, VIDEO*1 or S-VIDEO*1 inputs will have priority over DVI, VGA,
RGB/HV*1. When Y/Pb/Pr, Y/Pb/Pr2*1, SCART*1, VIDEO*1 or S-VIDEO*1 input signal is present
the monitor will change and keep to the Y/Pb/Pr, Y/Pb/Pr2*1, SCART*1, VIDEO*1 or S-VIDEO*1
input.
CUSTOM DETECT
Set the priority of input signals.
When CUSTOM DETECT is selected, monitor searches listed inputs only.
Priority of option input signal is only available in PRIORITY3 except for slot 2 type PC option.
LONG CABLE COMP*1
Manually compensates for image degradation caused from using a long cable.
(Analog input only)
ON/OFF
ON: Activates this function.
OFF: Deactivates this function.
OFF
0
SOG PEAK
Adjusts the sensitivity of the Sync On Green input signals. Adjusts the slice level when separating
synchronization from sync On Green signal input. Press “LEFT” or “RIGHT” to select.
GAIN
Adjusts gain value.
0
R-H.POSITION
G-H.POSITION
B-H.POSITION
Adjusts the position of the red component of the image.
Adjusts the position of the green component of the image.
Adjusts the position of the blue component of the image.
0
0
0
SYNC TERMINATION Selects the terminate resistance for matching the cable impedance.
INPUT CHANGE Sets input change speed. When selected “SUPER”, allows to switch high-speed between set two
HIGH
NORMAL
signals.
NOTE: When “QUICK” is selected, picture may be distorted when signal input is changed.
“SUPER” is released when selecting IMAGE FLIP except for NONE.
This function should be chosen after all adjustment options have been made for the input.
*1: This function depends on which option board you use.
*2: Only for DVI, DPORT, VGA, RGB/HV*1, HDMI, HDMI2*1, HDMI3*1 input.
English-27
TERMINAL SETTING
DVI MODE
Selects the kind of DVI-D equipment which is connected to the DVI input.
DVI-HD
Select “DVI-HD” when DVD player or computer equipment, which requires HDCP authentication,
is connected.
Select “DVI-PC” when a computer equipment, which not requires HDCP authentication, is
connected.
D-SUB MODE
Selects the type of signal associated with the D-SUB input.
RGB: Analog input (R, G, B, H, V)
COMPONENT: Component (Y, Cb/Pb, Cr/Pr)
RGB
RGB
BNC MODE*1
Selects the kind of equipment which is connected to the BNC input.
RGB: Analog input.
COMPONENT: Component.
SCART MODE*1
Input mode for devices using SCART connectors.
OFF
1.1a
DisplayPort
Selects DisplayPort mode [1.1a] or [1.2].
[1.2] should be selected when using Multi-Stream Transport.*2
HDMI SIGNAL
DEINTERLACE
RAW: Disable the expanded feature.
EXPAND: Expand image contrast and increase detail in the dark and bright areas.
Depends on
signal input
Selects the IP (Interlace to Progressive) conversion function.
ON
NOTE: For DVI input “DVI-HD” needs to be enabled in the DVI mode menu. When INPUT2 of
SUPER is selected in INPUT CHANGE and displayed, this function cannot be changed.
ON
Converts interlaced signals to progressive. This is the default setting.
OFF
Disables IP conversion. This setting is best suited for motion pictures, but increases the risk of
image retention.
COLOR SYSTEM*1
The selected Color System depends on the video format of the input signal.
AUTO
VIDEO, S-VIDEO inputs only
AUTO
NTSC
Automatically chooses Color System setting based on input signal.
PAL
SECAM
4.43 NTSC
PAL-60
OVER SCAN
Some video formats may require different scanning modes in order to best display the image.
ON
HDMI, Y/Pb/Pr, SCART*1, VIDEO*1, S-VIDEO*1,
HDMI2*1, HDMI3*1 inputs only
ON
Image size is larger than what can be displayed. The image edge will appear cropped.
Approximately 95% of the image will be shown on the screen.
OFF
Image size stays within the display area. The whole image is displayed on the screen.
NOTE: When you use a computer with HDMI out, please set “OFF”.
OPTION SETTING
OPTION POWER
You can set this setting when option board accessory is connected to the monitor.
Please contact your supplier for detailed information about Option board slot accessories.
-
Allow the monitor to supply power to Option board slot during power save mode or standby
OFF
mode.
NOTE: This function should be set to ON when using power save management by slot 2 type
option.
AUDIO
The function is available for slot 2 type option. Selects sound input signal according to slot2 type
option’s specifications. To activate DIGITAL, select OPTION for input signal and OPTION for
AUDIO INPUT.
ANALOG
NOTE: DIGITAL is activated only when OPTION is selected for input signal and OPTION for
AUDIO INPUT.
INTERNAL PC
OFF WARNING
The function is available for slot 2 type PC.
If OPTION POWER is OFF, a warning message appears when monitor power is turned off.
NOTE: Warning message does not appear when monitor power is turned off by OFF TIMER
setting or SCHEDULE setting.
OFF
OFF
AUTO OFF
Monitor power is automatically “OFF” when connected PC is OFF or the monitor is in power save
mode.
NOTE: Monitor power is not automatically “ON” when connected PC is ON.
START UP PC
FORCE QUIT
When ON is selected, connected PC start-up.
NO
NO
When ON is selected, it performs force-quit PC.
Please use this function only when the operating system cannot be shut down manually.
*1: This function depends on which option board you use.
*2: Multi-Stream Transport requires the corresponding display card. Contact your dealer for limitations of this function.
English-28
120Hz
(not adjustable)
-
-
-
TOUCH PANEL
RESET
(not adjustable)
Resets the following settings within the ADVANCED OPTION menu back to factory setting:
INPUT DETECT (except the priority of input signals), INPUT CHANGE (except for INPUT1 and
INPUT2), TERMINAL SETTING, DEINTERLACE, COLOR SYSTEM, OVER SCAN, AUDIO in
OPTION SETTING.
ADVANCED OPTION2
AUTO DIMMING
Adjusts the backlight of the LCD automatically depending on the amount of ambient light.
-
AUTO BRIGHTNESS
Adjusts the brightness level according to the input signal.
NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.
OFF
DPORT, DVI, VGA, RGB/HV*1 inputs only
ROOM LIGHT
SENSING*2
The backlight of the LCD screen can be set to increase or decrease depending on the amount of
ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If
the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the
viewing experience more comfortable to the eye in a variety of lighting conditions.
NOTE: When ROOM LIGHT SENSING is set to MODE1 or MODE2, BACKLIGHT, AUTO
BRIGHTNESS and BACKLIGHT in SCREEN SAVER function are disabled.
OFF
Do not cover the room light sensing sensor when you use MODE1 or MODE2.
AMBIENT parameter setting
ROOM LIGHT SENSING in OSD, select MODE1 or MODE2 and set MAX LIMIT, IN BRIGHT and
IN DARK in each mode.
MAX LIMIT: This is the max level of backlight which you set.
IN BRIGHT: This is the backlight level that the monitor will go up to when the ambient light level is
highest.
IN DARK: This is the level of backlight that the monitor will go down to when the ambient light
level is low.
When the ROOM LIGHT SENSING is enabled the Backlight level of the screen changes
automatically according to the lighting conditions of the room (see figure below).
Factory Setting
BACKLIGHT range
BACKLIGHT range when
set to MAX LIMIT.
BACKLIGHT level set for
the monitor to use when
ambient lighting level is
low.
BACKLIGHT level set
for the monitor to use
when ambient lighting
level is high.
IN DARK
dark
IN BRIGHT
room bright condition
bright
Screen Backlight value by MODE1
Screen Backlight value by MODE2
MAX LIMIT: BACKLIGHT level is limited to your set level.
IN DARK: BACKLIGHT level set for the monitor to use when ambient lighting level is low.
IN BRIGHT: BACKLIGHT level set for the monitor to use when ambient lighting level is high.
HUMAN SENSING*2
HUMAN SENSING has three settings.
DISABLE
NOTE: POWER SAVE is disabled when AUTO OFF or CUSTOM is selected in HUMAN
SENSING.
DISABLE
No human sensing.
-
-
AUTO OFF
At the preset time, when no person is detected, BACKLIGHT and VOLUME automatically go
into OFF. When a person comes near the monitor again, the monitor will automatically return to
normal mode.
CUSTOM
BACKLIGHT and VOLUME automatically shift to the set value when detecting no person. When
a person comes near the monitor again, the monitor automatically return to normal mode and
display the input signal selected in INPUT SELECT.
-
INTELLI. WIRELESS DATA Select “ON” to activate INTELLIGENT WIRELESS DATA function (see page 45). A password is
required when using the function.
ON
RESET
Resets “ADVANCED OPTION 2” settings back to factory setting, except for INTELLI. WIRELESS
DATA.
-
-
FACTORY RESET
All items are returned to factory shipment state.
NOTE: You can reset all items in all daisy chain displays. Please be careful to avoid resetting all
items inadvertently.
*1: This function depends on which option board you use.
*2: The function is available only when connecting the optional control unit.
English-29
NOTE 1: CREATING A SCHEDULE
The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be programmed.
To program the schedule:
1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET/POINT ZOOM or the + button
to enter the Settings menu. Highlight the desired schedule number and press SET/POINT ZOOM. The box next to the number will turn yellow.
The schedule can now be programmed.
2. Use the down button to highlight the hours setting in the ON time slot. Use the + and - buttons to set the hour. Use the up and down buttons to
highlight the minutes setting. Use the + and - buttons to set the minutes. Set the OFF time in the same manner.
3. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to highlight
PIC. MODE. Use the + and - buttons to choose the picture mode.
4. Use the down button to select a day on which the schedule will be enabled. Push the
SET/POINT ZOOM button to enable. If the schedule is to be ran every day, choose
EVERY DAY and press the SET/POINT ZOOM button. The circle next to EVERY DAY
will turn yellow. If a weekly schedule is desired, choose the days of the week using the up OFF TIMER
and down buttons and pressing SET/POINT ZOOM to select. Then highlight the EVERY
WEEK option and press SET/POINT ZOOM.
DVI
SCHEDULE:
(THU) JUN.18.2009 15:38
SETTINGS:
1
2
3
4
5
6
7
SCHEDULE SETTINGS
SCHEDULE LIST
DATE & TIME
RESET
ON:
– – : – –
– – : – –
– – – –
– – – –
OFF:
INPUT:
PIC. MODE:
5. After a schedule is programmed the remaining schedules can then be set. Press MENU
to leave the OSD or press EXIT to go back to the previous menu.
EVERY DAY
EVERY WEEK
MON
TUE
FRI
WED
SAT
THU
SUN
NOTE: If schedules are overlapping then the schedule with the highest number will have
priority over the schedule with the lowest number. For example schedule #7 will have
priority over schedule #1.
Return
Close
Choose
Mark
If selected input or picture mode is not available now, disable input or picture mode
is shown in red.
NOTE 2: IMAGE PERSISTENCE
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a
residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a long period of time should be avoided.
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at
regular intervals whenever the screen is idle or turning off the monitor when not in use.
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.
For long life use as Public Display
Image Sticking of LCD Panel
When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or
“ghost” image of previous image may be observed. (Image Persistence)
Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along the
displayed image, and may be permanent. (Image Sticking)
Recommendations
To prevent Image Sticking, and for longer life usage of LCD, the following are recommended.
1. Fixed image should not be displayed for long period. Change fixed images after short intervals.
2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule Functions.
3. Lower environmental temperatures prolong the lifespan of the monitor.
When Protective surface (glass, acrylic) is installed over the LCD surface, the LCD surface is located in an enclosed space, the monitor are
stacked, utilize the temperature sensors inside monitor.
To reduce the environmental temperature, use the Cooling Fan, Screen Saver and Low Brightness.
4. Please use “Screen Saver Mode” of monitor.
English-30
Remote Control Function
REMOTE CONTROL ID FUNCTION
Monitor ID:1
Monitor ID:2
Monitor ID:3
REMOTE CONTROL ID
The optional remote control can be used to control up to 100 individual MultiSync monitors
using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID
mode works in conjunction with the Monitor ID, allowing control of up to 100 individual
MultiSync monitors. For example: if there are many monitors being used in the same area,
a remote control in normal mode would send signals to every monitor at the same time (see
Figure 1). Using the remote in REMOTE CONTROL ID mode will only operate one specific
monitor within the group (see Figure 2).
Remote works
Remote works
Remote works
Figure 1
Remote in
Normal mode or
the REMOTE ID
is set to 0
TO SET REMOTE CONTROL ID
While holding down the REMOTE ID SET button on the remote control, use the KEYPAD to
input the Monitor ID (1-100) of the display to be controlled via remote. The remote can then
be used to operate the monitor having that specific Monitor ID number.
When 0 is selected or when the remote control is in normal mode, all monitors will be
operated.
Monitor ID:1
Monitor ID:2
Monitor ID:3
TO SET/RESET REMOTE CONTROL MODE
ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for
2 seconds.
Remote does
not work
Remote does
not work
Remote works
Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold
down for 2 seconds.
In order for this feature to work properly, the display must be assigned a Monitor ID number.
The Monitor ID number can be assigned under the MULTI DISPLAY menu in the OSD
(See page 24).
Figure 2
Remote set up
to use REMOTE
ID:3
Point the remote control towards the remote sensor of the desired monitor and press the
REMOTE ID SET button. The MONITOR ID number is shown on the display when your
remote control is in ID mode.
You need an optional remote control for this function.
Use the remote control to operate a monitor that has a specific MONITOR ID number assigned to it.
1. Set the MONITOR ID number for the display (See page 23). The MONITOR ID number can range from 1-100.
This MONITOR ID number allows the remote control to operate this specific monitor without affecting other monitors.
2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number
(1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose “0” to simultaneously
control all displays in range.
3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button.
The MONITOR ID number is shown in red on the display.
If the REMOTE CONTROLID is “0”, then all displays in range will show their respective MONITOR ID number in red.
If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same.
NOTE: GROUP ID cannot be specified via the remote control.
English-31
Multiple Monitors Connection
You can control multiple monitors by using RS-232C, REMOTE IN or LAN daisy-chain connection.
NOTE:
Multiple monitors that are daisy-chained have a limit to the connectable monitors.
When manually specify the ID number or control by the specified ID number, please execute AUTO ID (see page 24)
previously.
Main Monitor
Connector
Sub Monitors
Connector
IN
OUT
IN
OUT
RS-232C
REMOTE IN
LAN1
LAN2
LAN1
LAN2
Connection
MultiSync
MultiSync
LAN1 LAN2
LAN1 LAN2
LAN Cable
LAN Cable
MultiSync
English-32
Controlling the LCD monitor via RS-232C Remote Control
This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal.
Functions that can be controlled by a personal computer are:
•
•
•
Power ON or OFF.
Switching between input signals.
Sound Mute ON or OFF.
Connection
LCD Monitor + PC
MultiSync
PC
RS-232C
RS-232C Cable
NOTE:
If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your
dealer for details.
For the pin assignment, please see page 54 “2) RS-232C input/output”.
To control a monitor, please use the control command. Instructions for the control command can be found on the CD included
with the display. The file is called “External_control.pdf”.
1) Interface
PROTOCOL
BAUD RATE
DATA LENGTH
PARITY BIT
STOP BIT
RS-232C
9600 [bps]
8 [bits]
NONE
1 [bit]
FLOW CONTROL NONE
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
The reverse type cable (null modem cable) (not include) should be used for RS-232C control.
English-33
2) Control command diagram
For other commands, please see “External_Control.pdf” file on the CD-ROM.
Function (Monitor ID = 1)
Code Data
Power ON
01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 31 03 73 0d
01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 34 03 76 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 46 03 04 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 33 03 71 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 31 03 73 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 31 03 72 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 43 03 01 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 35 03 77 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 37 03 75 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 44 03 06 0d
01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 31 03 09 0d
01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 32 03 0a 0d
Power OFF
Input Source Select DisplayPort
Input Source Select DVI
Input Source Select VGA
Input Source Select HDMI
Input Source Select Y/Pb/Pr
Input Source Select VIDEO
Input Source Select S-VIDEO
Input Source Select OPTION
Sound Mute ON
Sound Mute OFF
English-34
Controlling the LCD monitor via LAN Control
Connecting to a Network
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function.
To use a LAN connection, you are required to assign an IP address.
Example of LAN connection:
Server
NOTE: Use a category 5 or higher LAN cable.
Hub
LAN cable
Network Setting by Using an HTTP Browser
Overview
Connecting the monitor to a network allows for monitor control from a computer via the network.
To perform the monitor control from a web browser, you must have an exclusive application installed on your computer.
The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP
server function. Please be sure to use “Microsoft Internet Explorer 7.0” or a higher version for the web browser.
(This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will
vary depending on the version of browser. Please refer to the help files and the other information provided in your software.)
Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the
monitor and entering the following URL.
Network Setting
TIP:
The default IP address is assigned automatically to the monitor.
The exclusive application can be downloaded from our website.
NOTE:
If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to
refresh your web browser (or clear the cache).
The display or button’s response can be slowed down or operation may not be accepted depending the settings of
your network. Should this happen, consult your network administrator.
The LCD monitor may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a
moment and repeat. If you still can’t get a response, turn the monitor off and then back on.
To control a monitor please use the control command. See “Control command diagram” (page 34).
English-35
Preparation Before Use
Connect the monitor to a commercially available LAN cable before engaging in browser operations.
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting
method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be
displayed depending on the effectiveness of the cache, and the contents set from the browser may not be reflected in operation.
It is recommended that a proxy server not be used unless it is unavailable.
Handling of the Address for Operation via a Browser
The host name can be used under the following cases:
If the host name corresponding to the IP address of the monitor has been registered to the domain name server (DNS) by the
network administrator, you can then access the network settings of the display via that registered host name using a compatible
browser.
If the host name corresponding to the IP address of the monitor has been configured in the “HOSTS” file of the computer being
used, you can then access the network settings of the display via that host name using a compatible browser.
Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by
Example 2: When the IP address of the monitor is “192.168.73.1”, access is gained to the mail alert settings by specifying
http://192.168.73.1/index.html for the address or the entry column of the URL.
Operation
Access the following address to show HOME. Click each link on the left side of HOME.
REMOTE CONTROL
Enable to control equivalent as the remote control key.
OSD menu
Enable to set the following OSD menu.
PICTURE, ADJUST, AUDIO, SCHEDULE, PIP, OSD, MULTI DISPLAY, DISPLAY PROTECTION, EXTERNAL CONTROL,
ADVANCED OPTION1, ADVANCED OPTION2.
NOTE:
Function of buttons which are shown on setting pages.
[APPLY]: Reflect your settings.
[CANCEL]: Return to the previous settings. NOTE: CANCEL is disabled after clicking APPLY.
[RELOAD]: Reload the settings.
[RESET]: Resets to the initial setting.
English-36
Network Setting
Click “NETWORK” on the left side of HOME.
IP SETTING
Set for IP ADDRESS setting.
AUTO: Automatically assign an IP address.
MANUAL: Set your IP address of the network connected to the monitor.
NOTE: Consult your network administrator for the IP address when [AUTO] is selected for
[IP SETTING].
IP ADDRESS
Set your IP address of the network connected to the monitor when [MANUAL] is selected for
[IP SETTING].
SUBNET MASK
Set your subnet mask number of the network connected to the monitor when [MANUAL] is selected
for [IP SETTING].
DEFAULT GATEWAY Set your default gateway of the network connected to the monitor when [MANUAL] is selected for
[IP SETTING].
NOTE: Set as [0.0.0.0] to delete the setting.
DNS
Set for IP ADDRESS setting of DNS server.
AUTO: Automatically assign an IP address of DNS server connected to the monitor.
MANUAL: Set your IP address of DNS server connected to the monitor.
PRIMARY DNS
Set your primary DNS settings of the network connected to the monitor.
NOTE: Set as [0.0.0.0] to delete the setting.
SECONDARY DNS
Set your secondary DNS settings of the network connected to the monitor.
NOTE: Set as [0.0.0.0] to delete the setting.
NOTE:
The following settings will reset back to the factory setting when “IP ADDRESS RESET” is selected by an EXTERNAL
CONTROL of OSD:
[IP SETTING]: AUTO, [IP ADDRESS]: 192.168.0.10, [SUBNET MASK]: 255.255.255.0, [DNS]: AUTO [DEFAULT
GATEWAY], [PRIMARY DNS] and [SECONDARY DNS] are blank.
English-37
Mail Setting
Click “MAIL” on the left side of HOME.
This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be
sent when an error occurs in the monitor.
ALERT MAIL
Checking [ENABLE] will turn on the Alert Mail feature.
Checking [DISABLE] will turn off the Alert Mail feature.
STATUS MESSAGE
Checking [ENABLE] will turn on the STATUS MESSAGE feature.
Checking [DISABLE] will turn off the STATUS MESSAGE feature.
SENDER’S ADDRESS
SMTP SERVER
Type in the senders address. Up to 60 alphanumeric and symbols characters can be used.
Type in the SMTP server name to be connected to the monitor.
Up to 60 alphanumeric characters can be used.
RECIPIENT’S
Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.
ADDRESS 1 TO 3
AUTHENTICATION
METHOD
This selects the authentication method of the e-mail transmission.
POP3 SERVER
USER NAME
This specifies the address of the POP3 server that is used in the authentication of the e-mail.
This sets the user name for logging into the authentication server when authentication is required
for the e-mail transmission. Up to 60 alphanumeric characters can be used.
PASSWORD
TEST MAIL
This sets the password for logging into the authentication server when authentication is required for
the e-mail transmission. Up to 60 alphanumeric characters can be used.
Click this button to send a test mail to check if your settings are correct.
NOTE:
• If you execute a test, you may not receive an Alert mail.
Should this happen, check if the network settings are correct.
• If you entered an incorrect address in a test, you may not receive an Alert mail.
Should this happen, check if the Recipient’s Address is correct.
TIP:
The Alert Mail settings will not be affected even when [RESET] is done from the menu.
For Control command diagram, please see file “External_Control.pdf” on the CD-ROM.
English-38
Alert error message list
Error number
* ErrorCode
Alert mail Message
Explanation
Measure
The monitor’s power supply is not
functioning normally.
Standby power Abnormal
Please contact your supplier.
70h ~ 7Fh
80h ~ Fh
The cooling fan has stopped.
Cooling fan Abnormal
Backlight abnormal
Please contact your supplier.
Please contact your supplier.
The monitor’s back light unit is not
functioning normally.
90h ~ 9Fh
A0h ~ AFh
The monitor is overheated.
Temperature Abnormal
Please contact your supplier.
SENSOR reached at the temperature
that the user had specified.
Reconfirm the setting condition from
OSD (DISPLAY PROTECTION-FAN
CONTROL) or please contact your
supplier.
A2h
*condition: DISPLAY PROTECTION-FAN
CONTROL-COOLING FAN = AUTO
The monitor doesn’t have the input
signal.
No signal
Please check “No picture” in
“Troubleshooting”.
B0h ~ BFh
D0h
The remaining capacity of the error log Proof of Play log memory size is 1 more
decreased.
Please get a log by using PD external
command. See page 44.
hour.
The system error occurred in the
monitor.
System error.
Please contact your supplier.
E0h ~ EFh
Sample: The following examples are content of Alert Mail that informs the temperature anomaly of monitor.
Sample: The following examples are content of test mail by browser.
English-39
SNMP Setting
Click “SNMP” on the left side of HOME.
This function allows for getting status and controlling of a monitor via the network.
Version:
SNMP v1 Authenticated plaintext by community name, not return a confirmation message of Trap.
SNMP v2c Authenticated plaintext by community name, return a confirmation message of Trap.
Community name:
The default setting of community name is “public”. It is read only. You can set community names for up to 3 settings.
Trap:
Sending error message to specified address when an error occurs in the monitor.
Check Box
Temperature
Explanation
Temperature abnormal
Cooling fan abnormal
Power abnormal
Error code
0xA0, 0xA1, 0xA2
Fan
0x80, 0x81
Power
0x70, 0x71, 0x72, 0x78
Inverter/Backlight
No Signal
Inverter or backlight abnormal 0x90, 0x91
No signal
0xB0
0xD0
0xE0
PROOF OF PLAY
System Error
Lower the log storage
System error
English-40
AMX Setting
Click “AMX” on the left side of HOME.
AMX BEACON
Turn on or off for detection from AMX Device Discovery when connecting to the network supported by
AMX’s NetLinx control system.
TIP:
When using a device that supports AMX Device Discovery, all AMX NetLinx control system will
recognize the device and download the appropriate Device Discovery Module from an AMX server.
Checking [ENABLE] will detect the device from AMX Device Discovery.
Checking [DISABLE] will not detect the device from AMX Device Discovery.
CRESTRON Setting
Click “CRESTRON” on the left side of HOME.
CRESTRON ROOMVIEW compatibility
The monitor supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and
controlled from a computer or a controller.
ROOMVIEW
ROOMVIEW for managing from the computer.
ON: Enables ROOMVIEW.
OFF: Disables ROOMVIEW.
CRESTRON
CONTROL
CRESTRON CONTROL for managing from the controller.
ON: Enables CRESTRON CONTROL.
OFF: Disables CRESTRON CONTROL.
CONTROLLER IP
ADDRESS
Set your IP address of CRESTRON SERVER.
IP ID
Set your IP ID of CRESTRON SERVER.
TIP: The CRESTRON settings are required only for use with CRESTRON ROOMVIEW.
For more information, visit http://www.crestron.com
English-41
Name Setting
Click “NAME” on the left side of HOME.
MONITOR NAME
HOST NAME
Set a monitor name. The name must be 16 characters or less. The default is model name.
Type in the hostname of the network connected to the monitor.
Up to 15 alphanumeric characters can be used.
DOMAIN NAME
Type in the domain name of the network connected to the monitor.
Up to 60 alphanumeric characters can be used.
Network Password Setting
Click “NETWORK PASSWORD” on the left side of HOME.
PJLink PASSWORD Set a password for PJLink*. A password must be 32 characters or less. Do not forget your password.
However, if you forget your password, consult with your dealer.
HTTP PASSWORD
Set a password for HTTP server. A password must be 10 characters or less.
HTTP PASSWORD
ENABLE
HTTP PASSWORD is required when logging in HTTP server.
Set a monitor name as USER NAME when inputting the password.
*What is PJLink?
PJLink is a standardization of protocol used for controlling devices of different manufacturers. This standard protocol is
established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005.
The device supports all the commands of PJLink Class 1.
Setting of PJLink will not be affected even when [RESET] is done from the menu.
English-42
PD List Information
Click “PD LIST” on the left side of HOME.
Show the list of ID and IP address of multiple monitors that are daisy-chained.
Only the master monitor can show the list.
Memo Setting
Click “MEMO” on the left side of HOME.
Set a title and meesage.
TITLE
A title must be 24 characters or less.
MESSAGE
A message must be 240 characters or less.
MEMO PASSWORD The default is “0000”.
MEMO PASSWORD MEMO PASSWORD is required when setting MEMO.
ENABLE
English-43
POINT ZOOM
Using “SET/POINT ZOOM” button on a remote control allows to enlarge a partial of image.
Press CH+/- button to zoom up or down. The image can be expanded from 1 to 10 times.
1
2
3
4
5
6
Press [SET/POINT ZOOM] button on a remote control. An icon will be a magnifier.
Move magnifier icon by [ ] [ ] [+] [-] button.
Press [CH+] to zoom up. Press [CH-] to zoom down.
Press [SET/POINT ZOOM] to disappear the icon.
Press [EXIT] to return to a normal size.
Press [MENU] to display OSD menu.<Setting Procedure>
NOTE:
• The image may be distorted during this function.
• This function does not work when set to PIP, POP, PBP, TILE MATRIX, SCREEN SAVER, SUPER in INPUT
CHANGE, IMAGE FLIP.
• When selected DYNAMIC or ZOOM in ASPECT, the image will be changed FULL, then start to POINT ZOOM.
After POINT ZOOM, the ASPECT will be returned previous ASPECT settings. When the ASPECT is changed
during POINT ZOOM, DYNAMIC and ZOOM will be FULL image.
• The magnifier icon does not move to no image area.
• POINT ZOOM will be released after changing input signal or power off.
• POINT ZOOM will be released when setting IMAGE FLIP or changing ASPECT setting during POINT ZOOM.
PROOF OF PLAY
This function allows to send message for the current status of monitor by self checking.
Check item
INPUT
Message
DVI, VGA, Y/Pb/Pr, HDMI, DPORT, HDMI2*, HDMI3*, RGB/HV*, Y/Pb/Pr2*, SCART*, VIDEO*,
S-VIDEO*, OPTION*
①
Resolution
ex. (H)1920, (V)1080 , (H)1360, (V)768 or No signal or Invalid signal
IN1, IN2, IN3*, HDMI, DPORT, HDMI2*, HDMI3*, OPTION (analog)*, OPTION (digital)*
Audio in or No Audio in or N/A (IN1, IN2, IN3*, OPTION (analog)*)
Normal Picture or No Picture
②
③
④
⑤
⑥
⑦
Audio INPUT
Audio signal
Picture Image
Audio out
Normal Audio or No Audio
Cumulative time
(hour)/(minutes)/(second)
*: This function depends on which option board you use.
Sample:
HDMI
①
②
③
④
⑤
⑥
⑦
1920 x 1080
HDMI
Audio in
Normal Picture
Normal Audio
0h/0m/0s
NOTE:
For Proof of Play function, please see “External_Control.pdf” on the CD-ROM.
English-44
INTELLIGENT WIRELESS DATA
This function allows to get the data of monitor’s status by wireless communication even while the monitor is off.
Some menu of OSD, you can set by this function.
NOTE:
Sensor position: see page 9.
Please contact your supplier for detailed information.
Function name
Item Name
Read/Write
R/W
INPUT TYPE
PICTURE
ADJUST
AUDIO
R/W
R/W
R/W
SCHEDULE
PIP
R/W
R/W
Setting read and write
function
OSD
R/W
MULTI DISPLAY
R/W
DISPLAY PROTECTION
EXTERNAL CONTROL
ADVANCED OPTION1
ADVANCED OPTION2
FACTORY RESET
MODEL NAME
R/W
R/W
R/W
R/W
R/W
Read only
Read only
Read only
Read only
Read only
Read only
Read only
SERIAL NUMBER
MANUFACTURED DATE
FIRMWARE1
Display information
All data for service
FIRMWARE2
MAC ADDRESS
English-45
Features
Ultra Narrow Bezel: Provides the optimum solution in a tiling environment.
Reduced Footprint: Provides the ideal solution for environments with superior image quality.
Color Control Systems: Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a
variety of standards.
OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six
axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard provides
the monitor with a uniform color profile. This assures that the colors displayed on the monitor are exactly the same as on the
color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your screen
and customise the color accuracy of your monitor to a variety of standards.
sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays and
other peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation and
backward compatibility with other common color standards.
OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use
on-screen menus.
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing
the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically
optimizing display performance.
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a
lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and
lowering the air conditioning costs of the workplace.
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.
VESA Standard (FDMIv1) Mounting Interface: Allows you to connect your LCD monitor to any VESA standard (FDMIv1) third
party mounting arm or bracket. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard
in North America.
DVI-D: The digital-only subset of DVI ratified by the Digital Display Working Group (DDWG) for digital connections between
computers and displays. As a digital-only connector, analog support is not provided for a DVI-D connector. As a DVI-based
digital only connection, only a simple adapter is necessary for compatibility between DVI-D and other DVI-based digital
connectors such as DFP and P&D. The DVI interface of this display supports HDCP.
TILE MATRIX,TILE COMP: Shows one image over multiple screens with accuracy while compensating for bezel width.
ZOOM: Expands/reduces image size for horizontal and vertical direction.
Self-diagnosis: If an internal error should occur, a failure state will be indicated.
HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent over
a Digital Visual Interface (DVI). If you are unable to view material via the DVI input, this does not necessarily mean the display is
not functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP
and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).
Option board slot: You can use an option board. Please contact your supplier for detailed information.
English-46
Troubleshooting
LED on monitor is not lit (no green or red color can be seen)
No picture
•
Power Switch should be in the ON position and power cord
should be connected.
•
The signal cable should be completely connected to the
display card/computer.
•
•
Check the main Power Switch, it should be in the ON position.
•
•
•
The display card should be completely seated in its slot.
Make certain the computer is not in a power-saving mode
(touch the keyboard or mouse).
Check the main Power Switch, it should be in the ON position.
Power Switch and computer power switch should be in the
ON position.
•
Check to see that the power indicator option in the OSD is set
to ON.
•
Check to make sure that a supported mode has been
selected on the display card or system being used. (Please
consult display card or system manual to change graphics
mode.)
RED LED on monitor is blinking
•
A certain failure might have occurred, please contact your
nearest authorized NEC DISPLAY SOLUTIONS service
facility.
•
Check the monitor and your display card with respect to
compatibility and recommended settings.
•
If the monitor is powered off by the inside temperature being
higher than the normal operating temperature, a RED LED will
blink six times. Power on the display again after confirming
the inside temperature has been reduced to normal operation
temperature.
•
•
Check the signal cable connector for bent or pushed-in pins.
The monitor automatically goes into OFF at the preset time
period after signal is lost. Press the power button.
Power Button does not respond
•
Display image is not sized properly
•
Unplug the power cord of the monitor from the AC outlet to
turn off and reset the monitor.
Use the OSD Image Adjust controls to increase or decrease
the coarse adjustment.
•
•
Check the main Power Switch on the back side of the monitor.
•
Check to make sure that a supported mode has been
selected on the display card or system being used.
(Please consult display card or system manual to change
graphics mode.)
Check the DVI MODE setting when DVD player or computer
equipment is connected to the DVI input.
Snowy Picture, Black Screen in DVI input
•
Check the DVI MODE setting when DVD player or computer
equipment is connected to the DVI input.
Selected resolution is not displayed properly
•
Use OSD Display Mode to enter Information menu and
confirm that the appropriate resolution has been selected. If
not, select corresponding option.
Image persistence
•
Please be aware that LCD Technology may experience
a phenomenon known as Image Persistence. Image
Persistence occurs when a residual or “ghost” image of a
previous image remains visible on the screen. Unlike CRT
monitors, LCD monitors’ image persistence is not permanent,
but constant images being displayed for a long period of time
should be avoided. To alleviate image persistence, turn off the
monitor for as long as the previous image was displayed. For
example, if an image was on the monitor for one hour and a
residual image remains, the monitor should be turned off for
one hour to erase the image.
No Sound
•
•
•
•
Check to see if audio cable is properly connected.
Check to see if mute is activated.
Check to see if volume is set at minimum.
Check to see if computer supports an audio signal through
DisplayPort.
If unsure, contact the computer manufacturer.
•
Check to see if SURROUND is ON.
Remote Control is not available
NOTE:
As with all personal display devices, NEC DISPLAY
SOLUTIONS recommends displaying moving images
and using a moving screen saver at regular intervals
whenever the screen is idle or turning off the monitor
when not in use.
•
•
•
Check the Remote Control’s batteries status.
Check if batteries are inserted correctly.
Check if the Remote Control is pointing at the monitor’s
remote sensor.
•
•
Check the IR LOCK SETTING status.
Image is unstable, unfocused or swimming is apparent
The remote control system may not function when direct
sunlight or strong illumination strikes the remote control
sensor of the LCD monitor, or when there is an object in the
path.
•
Signal cable should be completely attached to the computer.
•
Use the OSD Image Adjust controls to focus and adjust
display by increasing or decreasing the fine adjustment.
When the display mode is changed, the OSD Image Adjust
settings may need to be re-adjusted.
“SCHEDULE”/“OFF TIMER” function is not working properly
•
The “SCHEDULE” function will be disabled when the “OFF
TIMER” is set.
•
•
•
Check the monitor and your display card with respect to
compatibility and recommended signal timings.
•
If the “OFF TIMER” function is enabled and the power to
the LCD monitor is turned off when the power supply is
interrupted unexpectedly, then the “OFF TIMER” will be reset.
If your text is garbled, change the video mode to non-interlace
and use 60Hz refresh rate.
The image may be distorted when turning the power on or
changing the settings.
Snowy Picture, Poor Sound in TV
Check antenna/cable connection. Use new cable if necessary.
•
Image of component signal is greenish
Check to see if the Y/Pb/Pr input connector is selected.
•
Interference in TV
•
Check components for shielding, move away from monitor if
necessary.
RS-232C or LAN control is not available
Check RS-232C or LAN cable connection.
•
Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or degradation.
English-47
Specifications - X464UN
Product Specifications
LCD Module
46”/1168 mm diagonal
Pixel Pitch: 0.530 mm
Resolution: 1920 x 1080
Color: Over 16 million colors (depending on display card used)
Brightness: 700 cd/m2 (Max.) @25°C
Contrast Ratio: 3500:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Pixel Clock
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz
50.0 - 85.0 Hz (Analog Input)
Vertical: 24.0 - 85.0 Hz (Digital Input)
Analog: 13.5 MHz, 25.0 MHz - 195.0 MHz
Digital: 25.0 MHz - 165.0 MHz (DVI)
25.0 MHz - 300.0 MHz (HDMI/DisplayPort)
Viewable Size
Input Signal
DVI
1018.1 x 572.7 mm
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz), 1080p, 1080i
DisplayPort DisplayPort Connector Digital RGB
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*1, *4
VGA*2
HDMI
15pin Mini D-sub
Analog RGB
Sync
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI Connector
15pin Mini D-sub
Digital YUV
Digital RGB
HDMI
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,
3840x2160 (30Hz/24Hz/25Hz)*1, *4, 4096x2160 (24Hz)*1, *4
Y/Pb/Pr*2
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
Output Signal
DisplayPort DisplayPort Connector Digital RGB
AUDIO
AUDIO
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
Stereo L/R 0.5 Vrms
STEREO Mini Jack
Analog Audio
Input
HDMI Connector
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
STEREO Mini Jack Analog Audio
AUDIO
Output
Speaker Output
Control
External Speaker Jack 15 W + 15 W (8 ohm)
RS-232C In: 9 Pin D-sub
LAN: RJ-45 10/100 BASE-T
Remote IN: Stereo Mini jack 3.5
Service port
USB service port for maintenance
3.0 - 1.2 A @ 100-240V AC, 50/60Hz
Temperature*3: 0 - 40°C / 32 - 104°F
Power Supply
Operational Environment
Storage Environment
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
1024.0 (W) x 578.6 (H) x 99.7 (D) mm / 40.3 (W) x 22.8 (H) x 3.9 (D) inches
Weight
23.0 kg (50.7 lbs)
VESA compatible mounting interface
Power Management
Plug & Play
300 mm x 300 mm (M6, 4 Holes)
VESA DPM
VESA DDC2B, DDC/CI, DisplayPort
16V/3.6 A
Power supply for Slot 2 type OPTION
Accessories
Setup manual, Power Cord, Video Signal cable (DisplayPort to DisplayPort cable), LAN cable,
Clamp x 1, Screw x 1, CD-ROM
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: Common terminal.
*3: When you use option board accessories, please contact your supplier for detailed information.
*4: Displayed text may be blurred.
English-48
Specifications - X464UNS
Product Specifications
LCD Module
46”/1168 mm diagonal
Pixel Pitch: 0.530 mm
Resolution: 1920 x 1080
Color: Over 16 million colors (depending on display card used)
Brightness: 700 cd/m2 (Max.) @25°C
Contrast Ratio: 3500:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Pixel Clock
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz
50.0 - 85.0 Hz (Analog Input)
Vertical: 24.0 - 85.0 Hz (Digital Input)
Analog: 13.5 MHz, 25.0 MHz - 195.0 MHz
Digital: 25.0 MHz - 165.0 MHz (DVI)
25.0 MHz - 300.0 MHz (HDMI/DisplayPort)
Viewable Size
Input Signal
DVI
1018.1 x 572.7 mm
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz), 1080p, 1080i
DisplayPort DisplayPort Connector Digital RGB
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*1, *4
VGA*2
HDMI
15pin Mini D-sub
Analog RGB
Sync
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI Connector
15pin Mini D-sub
Digital YUV
Digital RGB
HDMI
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,
3840x2160 (30Hz/24Hz/25Hz)*1, *4, 4096x2160 (24Hz)*1, *4
Y/Pb/Pr*2
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
Output Signal
DisplayPort DisplayPort Connector Digital RGB
AUDIO
AUDIO
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
Stereo L/R 0.5 Vrms
STEREO Mini Jack
Analog Audio
Input
HDMI Connector
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
STEREO Mini Jack Analog Audio
AUDIO
Output
Speaker Output
Control
External Speaker Jack 15 W + 15 W (8 ohm)
RS-232C In: 9 Pin D-sub
LAN: RJ-45 10/100 BASE-T
Remote IN: Stereo Mini jack 3.5
Service port
USB service port for maintenance
3.0 - 1.2 A @ 100-240V AC, 50/60Hz
Temperature*3: 0 - 40°C / 32 - 104°F
Power Supply
Operational Environment
Storage Environment
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
1022.0 (W) x 576.6 (H) x 101.3 (D) mm / 40.2 (W) x 22.7 (H) x 4.0 (D) inches
Weight
20.4 kg (45.0 lbs)
VESA compatible mounting interface
Power Management
Plug & Play
300 mm x 300 mm (M6, 4 Holes)
VESA DPM
VESA DDC2B, DDC/CI, DisplayPort
16V/3.6 A
Power supply for Slot 2 type OPTION
Accessories
Setup manual, Power Cord, Video Signal cable (DisplayPort to DisplayPort cable), LAN cable,
Clamp x 1, Screw x 1, CD-ROM
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: Common terminal.
*3: When you use option board accessories, please contact your supplier for detailed information.
*4: Displayed text may be blurred.
English-49
Specifications - X464UNV
Product Specifications
LCD Module
46”/1168 mm diagonal
Pixel Pitch: 0.530 mm
Resolution: 1920 x 1080
Color: Over 16 million colors (depending on display card used)
Brightness: 500 cd/m2 (Max.) @25°C
Contrast Ratio: 3500:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Pixel Clock
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz
50.0 - 85.0 Hz (Analog Input)
Vertical: 24.0 - 85.0 Hz (Digital Input)
Analog: 13.5 MHz, 25.0 MHz - 195.0 MHz
Digital: 25.0 MHz - 165.0 MHz (DVI)
25.0 MHz - 300.0 MHz (HDMI/DisplayPort)
Viewable Size
Input Signal
DVI
1018.1 x 572.7 mm
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz), 1080p, 1080i
DisplayPort DisplayPort Connector Digital RGB
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*1, *4
VGA*2
HDMI
15pin Mini D-sub
Analog RGB
Sync
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI Connector
15pin Mini D-sub
Digital YUV
Digital RGB
HDMI
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,
3840x2160 (30Hz/24Hz/25Hz)*1, *4, 4096x2160 (24Hz)*1, *4
Y/Pb/Pr*2
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
Output Signal
DisplayPort DisplayPort Connector Digital RGB
AUDIO
AUDIO
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
Stereo L/R 0.5 Vrms
STEREO Mini Jack
Analog Audio
Input
HDMI Connector
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
STEREO Mini Jack Analog Audio
AUDIO
Output
Speaker Output
Control
External Speaker Jack 15 W + 15 W (8 ohm)
RS-232C In: 9 Pin D-sub
LAN: RJ-45 10/100 BASE-T
Remote IN: Stereo Mini jack 3.5
Service port
USB service port for maintenance
2.6 - 1.1 A @ 100-240V AC, 50/60Hz
Temperature*3: 0 - 40°C / 32 - 104°F
Power Supply
Operational Environment
Storage Environment
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
1024.0 (W) x 578.6 (H) x 117.3 (D) mm / 40.3 (W) x 22.8 (H) x 4.6 (D) inches
Weight
22.8 kg (50.3 lbs)
VESA compatible mounting interface
Power Management
Plug & Play
300 mm x 300 mm (M6, 4 Holes)
VESA DPM
VESA DDC2B, DDC/CI, DisplayPort
16V/3.6 A
Power supply for Slot 2 type OPTION
Accessories
Setup manual, Power Cord, Video Signal cable (DisplayPort to DisplayPort cable), LAN cable,
Clamp x 1, Screw x 1, CD-ROM
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: Common terminal.
*3: When you use option board accessories, please contact your supplier for detailed information.
*4: Displayed text may be blurred.
English-50
Specifications - X554UN
Product Specifications
LCD Module
55”/1388 mm diagonal
Pixel Pitch: 0.630 mm
Resolution: 1920 x 1080
Color: Over 16 million colors (depending on display card used)
Brightness: 700 cd/m2 (Max.) @25°C
Contrast Ratio: 3500:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Pixel Clock
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz
50.0 - 85.0 Hz (Analog Input)
Vertical: 24.0 - 85.0 Hz (Digital Input)
Analog: 13.5 MHz, 25.0 MHz - 195.0 MHz
Digital: 25.0 MHz - 165.0 MHz (DVI)
25.0 MHz - 300.0 MHz (HDMI/DisplayPort)
Viewable Size
Input Signal
DVI
1209.6 x 680.4 mm
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz), 1080p, 1080i
DisplayPort DisplayPort Connector Digital RGB
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*1, *4
VGA*2
HDMI
15pin Mini D-sub
Analog RGB
Sync
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI Connector
15pin Mini D-sub
Digital YUV
Digital RGB
HDMI
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,
3840x2160 (30Hz/24Hz/25Hz)*1, *4, 4096x2160 (24Hz)*1, *4
Y/Pb/Pr*2
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
Output Signal
DisplayPort DisplayPort Connector Digital RGB
AUDIO
AUDIO
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
Stereo L/R 0.5 Vrms
STEREO Mini Jack
Analog Audio
Input
HDMI Connector
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
STEREO Mini Jack Analog Audio
AUDIO
Output
Speaker Output
Control
External Speaker Jack 15 W + 15 W (8 ohm)
RS-232C In: 9 Pin D-sub
LAN: RJ-45 10/100 BASE-T
Remote IN: Stereo Mini jack 3.5
Service port
USB service port for maintenance
3.8 - 1.6 A @ 100-240V AC, 50/60Hz
Temperature*3: 0 - 40°C / 32 - 104°F
Power Supply
Operational Environment
Storage Environment
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
1215.3 (W) x 686.1 (H) x 99.6 (D) mm / 47.8 (W) x 27.0 (H) x 3.9 (D) inches
Weight
29.2 kg (64.4 lbs)
VESA compatible mounting interface
Power Management
Plug & Play
400 mm x 400 mm (M6, 4 Holes)
VESA DPM
VESA DDC2B, DDC/CI, DisplayPort
16V/3.6 A
Power supply for Slot 2 type OPTION
Accessories
Setup manual, Power Cord, Video Signal cable (DisplayPort to DisplayPort cable), LAN cable,
Clamp x 3, Screw x 3, CD-ROM, Thumbscrew for optional stand x 2
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: Common terminal.
*3: When you use option board accessories, please contact your supplier for detailed information.
*4: Displayed text may be blurred.
English-51
Specifications - X554UNS
Product Specifications
LCD Module
55”/1388 mm diagonal
Pixel Pitch: 0.630 mm
Resolution: 1920 x 1080
Color: Over 16 million colors (depending on display card used)
Brightness: 700 cd/m2 (Max.) @25°C
Contrast Ratio: 3500:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Pixel Clock
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz
50.0 - 85.0 Hz (Analog Input)
Vertical: 24.0 - 85.0 Hz (Digital Input)
Analog: 13.5 MHz, 25.0 MHz - 195.0 MHz
Digital: 25.0 MHz - 165.0 MHz (DVI)
25.0 MHz - 300.0 MHz (HDMI/DisplayPort)
Viewable Size
Input Signal
DVI
1209.6 x 680.4 mm
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz), 1080p, 1080i
DisplayPort DisplayPort Connector Digital RGB
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*1, *4
VGA*2
HDMI
15pin Mini D-sub
Analog RGB
Sync
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI Connector
15pin Mini D-sub
Digital YUV
Digital RGB
HDMI
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,
3840x2160 (30Hz/24Hz/25Hz)*1, *4, 4096x2160 (24Hz)*1, *4
Y/Pb/Pr*2
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
Output Signal
DisplayPort DisplayPort Connector Digital RGB
AUDIO
AUDIO
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
Stereo L/R 0.5 Vrms
STEREO Mini Jack
Analog Audio
Input
HDMI Connector
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
STEREO Mini Jack Analog Audio
AUDIO
Output
Speaker Output
Control
External Speaker Jack 15 W + 15 W (8 ohm)
RS-232C In: 9 Pin D-sub
LAN: RJ-45 10/100 BASE-T
Remote IN: Stereo Mini jack 3.5
Service port
USB service port for maintenance
3.8 - 1.6 A @ 100-240V AC, 50/60Hz
Temperature*3: 0 - 40°C / 32 - 104°F
Power Supply
Operational Environment
Storage Environment
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
1213.5 (W) x 684.3 (H) x 100.4 (D) mm / 47.8 (W) x 26.9 (H) x 4.0 (D) inches
Weight
27.9 kg (61.5 lbs)
VESA compatible mounting interface
Power Management
Plug & Play
400 mm x 400 mm (M6, 4 Holes)
VESA DPM
VESA DDC2B, DDC/CI, DisplayPort
16V/3.6 A
Power supply for Slot 2 type OPTION
Accessories
Setup manual, Power Cord, Video Signal cable (DisplayPort to DisplayPort cable), LAN cable,
Clamp x 3, Screw x 3, CD-ROM, Thumbscrew for optional stand x 2
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: Common terminal.
*3: When you use option board accessories, please contact your supplier for detailed information.
*4: Displayed text may be blurred.
English-52
Specifications - X554UNV
Product Specifications
LCD Module
55”/1388 mm diagonal
Pixel Pitch: 0.630 mm
Resolution: 1920 x 1080
Color: Over 16 million colors (depending on display card used)
Brightness: 500 cd/m2 (Max.) @25°C
Contrast Ratio: 3500:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Pixel Clock
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz
50.0 - 85.0 Hz (Analog Input)
Vertical: 24.0 - 85.0 Hz (Digital Input)
Analog: 13.5 MHz, 25.0 MHz - 195.0 MHz
Digital: 25.0 MHz - 165.0 MHz (DVI)
25.0 MHz - 300.0 MHz (HDMI/DisplayPort)
Viewable Size
Input Signal
DVI
1209.6 x 680.4 mm
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz), 1080p, 1080i
DisplayPort DisplayPort Connector Digital RGB
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*1, *4
VGA*2
HDMI
15pin Mini D-sub
Analog RGB
Sync
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920X1080 (60Hz)
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
HDMI Connector
15pin Mini D-sub
Digital YUV
Digital RGB
HDMI
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, WUXGA60*1, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,
3840x2160 (30Hz/24Hz/25Hz)*1, *4, 4096x2160 (24Hz)*1, *4
Y/Pb/Pr*2
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
Output Signal
DisplayPort DisplayPort Connector Digital RGB
AUDIO
AUDIO
DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3
Stereo L/R 0.5 Vrms
STEREO Mini Jack
Analog Audio
Input
HDMI Connector
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
STEREO Mini Jack Analog Audio
AUDIO
Output
Speaker Output
Control
External Speaker Jack 15 W + 15 W (8 ohm)
RS-232C In: 9 Pin D-sub
LAN: RJ-45 10/100 BASE-T
Remote IN: Stereo Mini jack 3.5
Service port
USB service port for maintenance
2.9 - 1.1 A @ 100-240V AC, 50/60Hz
Temperature*3: 0 - 40°C / 32 - 104°F
Power Supply
Operational Environment
Storage Environment
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
1213.5 (W) x 684.3 (H) x 100.4 (D) mm / 47.8 (W) x 26.9 (H) x 4.0 (D) inches
Weight
25.2 kg (55.6 lbs)
VESA compatible mounting interface
Power Management
Plug & Play
400 mm x 400 mm (M6, 4 Holes)
VESA DPM
VESA DDC2B, DDC/CI, DisplayPort
16V/3.6 A
Power supply for Slot 2 type OPTION
Accessories
Setup manual, Power Cord, Video Signal cable (DisplayPort to DisplayPort cable), LAN cable,
Clamp x 3, Screw x 3, CD-ROM, Thumbscrew for optional stand x 2
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: Common terminal.
*3: When you use option board accessories, please contact your supplier for detailed information.
*4: Displayed text may be blurred.
English-53
Pin Assignment
1) Analog multi input (MiniDsub15p): VGA, Y/Pb/Pr
Pin No Name
1
2
Red, Y/Pb/Pr_Pr
Green, Y/Pb/Pr_Y
Blue, Y/Pb/Pr_Pb
GND
3
4
Mini D-SUB 15P (Monitor side)
5
DDC-GND
Red-GND
Green-GND
Blue-GND
+5V (DDC)
GND
1
5
6
6
7
10
15
11
8
9
10
11
12
13
14
15
NC
DDC-SDA
H-SYNC
V-SYNC
DDC-SCL
2) RS-232C input/output
Pin No Name
1
2
3
4
5
6
7
8
9
NC
D-SUB 9P (Monitor side)
RXD
TXD
NC
5
1
GND
NC
6
9
NC
NC
NC
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
English-54
Manufacturer’s Recycling and Energy Information
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top
priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly
products, and always strive to help define and comply with the latest independent standards from agencies such as ISO
(International Organisation for Standardization) and TCO (Swedish Trades Union).
Disposing of your old NEC product
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures
and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.
All required information concerning the disposal of the product and country-specific information on recycling facilities can be
found on our following websites:
http://www.nec-display-solutions.com/greencompany/ (in Europe),
http://www.nec-display.com (in Japan) or
http://www.necdisplay.com (in USA).
Energy Saving
This monitor features an advanced energy saving capability. When a Display Power Management signal is sent to the monitor,
the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.
Mode
Power consumption
LED colour
Approx. 120 W (X464UN)
Approx. 120 W (X464UNS)
Approx. 90 W (X464UNV)
Approx. 150 W (X554UN)
Approx. 150 W (X554UNS)
Approx. 110 W (X554UNV)
Normal Operation*1, *2
Green
Energy Saving Mode (AUTO POWER SAVE)
Energy Saving Mode*1 (AUTO STANDBY)
Power Off
Less than 2.5 W
Less than 0.5 W
Less than 0.5 W
Amber
Red
Red
*1: without any option, with factory settings.
*2: depends on destination.
For additional information visit:
http://www.necdisplay.com/ (in USA)
http://www.nec-display-solutions.com/ (in Europe)
WEEE Mark (European Directive 2012/19/EU)
Within the European Union
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic
products carrying the mark (left) must be disposed of separately from normal household waste. This includes
monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your
NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased
the product, or if applicable, follow any agreements made between yourself and NEC.
The mark on electrical and electronic products only applies to the current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority
so as to comply with the correct disposal method.
English-55
|