NEC MULTISYNC X554UNS 02 User Manual

User’s Manual

MultiSync X464UN

MultiSync X464UNV

MultiSync X554UN

MultiSync X554UNS

Declaration of conformity

FCC Information

1. Use the attached speciﬁed cables with the MultiSync X464UN (X464UN)/MultiSync X464UNV (X464UNV)/MultiSync X554UN

(X554UN)/MultiSync X554UN (X554UN(C))/MultiSync X554UNS (X554UNS) color display so as not to interfere with radio and

television reception.

(1) Please use the supplied power cord or equivalent to ensure FCC compliance.

(2) Please use a good quality shielded video signal cable.

Use of other cables and adapters may cause interference with radio and television reception.

2. This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.

The user may ﬁnd the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify

and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Ofﬁce, Washington,

D.C., 20402, Stock No. 004-000-00345-4.

Windows is a registered trademark of Microsoft Corporation.

NEC is a registered trademark of NEC Corporation.

OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and

Switzerland.

DisplayPort and DisplayPort Compliance Logo are trademarks owned by the Video Electronics Standards

Association.

All other brands and product names are trademarks or registered trademarks of their respective owners.

HDMI, the HDMI logo and High-Deﬁnition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC

in the United States and other countries.

Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and

areas.

CRESTRON and ROOMVIEW are registered trademarks of Crestron Electronics, Inc. in the United States and other countries.

GPL/LGPL Software Licenses

The product includes software licensed under GNU General Public License (GPL), GNU Lesser General Public License (LGPL),

and others.

For more information on each software, see “readme.pdf” inside the “about GPL&LGPL” folder on the supplied CD-ROM.

English-1

Important Information

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT

USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE

PRONGS CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM

WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER

CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have sufﬁcient magnitude to cause electric

shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has

been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION: Please use the power cord provided with this monitor in accordance with the table below. If a power cord is not

supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the

AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.

European

Continental

Plug Type

North America

U.K.

Chinese

Japanese

Plug Shape

U.S.A./

Canada

Region

Voltage

Taiwan

110

EU (except U.K.)

230

U.K.

230

China

220

Japan

100

120*

* When operating the MultiSync monitor with its AC 125-240V power supply, use a power supply cord that matches the power

supply voltage of the AC power outlet being used.

NOTE:

This product can only be serviced in the country where it was purchased.

Use the power cord which has BSMI mark at both ends when you use this monitor in Taiwan.

•

The intended primary use of this product is as an Information Technical Equipment in an ofﬁce or domestic environment.

The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.

Warning

This is a class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

English-2

Safety Precautions, Maintenance & Recommended Use

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE

FOLLOWING WHEN SETTING UP AND USING

THE MULTI-FUNCTION MONITOR:

Immediately unplug your monitor from the wall outlet and refer

servicing to qualiﬁed service personnel under the following

conditions:

•

DO NOT OPEN THE MONITOR. There are no user

serviceable parts inside and opening or removing covers may

expose you to dangerous shock hazards or other risks. Refer

all servicing to qualiﬁed service personnel.

•

When the power supply cord or plug is damaged.

If liquid has been spilled, or objects have fallen into the monitor.

If the monitor has been exposed to rain or water.

If the monitor has been dropped or the cabinet damaged.

•

Do not spill any liquids into the cabinet or use your monitor

near water.

If you notice any structural damage such as cracks or

unnatural wobbling.

Do not insert objects of any kind into the cabinet slots, as they

may touch dangerous voltage points, which can be harmful or

fatal or may cause electric shock, ﬁre or equipment failure.

•

If the monitor does not operate normally by following

operating instructions.

•

Do not place any heavy objects on the power cord.

Damage to the cord may cause shock or ﬁre.

Recommended Use

•

For optimum performance, allow 20 minutes for warm-up.

Do not place this product on a sloping or unstable cart, stand

or table, as the monitor may fall, causing serious damage to

the monitor.

Rest your eyes periodically by focusing on an object at least

5 feet away. Blink often.

•

Position the monitor at a 90° angle to windows and other light

sources to minimize glare and reﬂections.

•

Do not mount this product face up, face down or upside down

for an extended period of time as it may cause permanent

damage to the screen.

Clean the LCD monitor surface with a lint-free, non-abrasive

cloth. Avoid using any cleaning solution or glass cleaner!

The power supply cord you use must have been approved by

and comply with the safety standards of your country. (Type

H05VV-F 3G 1mm²should be used in Europe)

Adjust the monitor’s brightness, contrast and sharpness

controls to enhance readability.

•

In UK, use a BS-approved power cord with molded plug

having a black (13A) fuse installed for use with this monitor.

Avoid displaying ﬁxed patterns on the monitor for long

periods of time to avoid image persistence (after image

effects).

Do not place any objects onto the monitor and do not use the

monitor outdoors.

•

Get regular eye checkups.

•

Do not bend, crimp or otherwise damage the power cord.

If glass is broken, handle with care.

Ergonomics

To realize the maximum ergonomic beneﬁts, we recommend the

following:

Do not cover vent on monitor.

Do not use monitor in high temperature, humid, dusty, or oily

areas.

•

Use the preset Size and Position controls with standard

signals.

•

If monitor or glass is broken, do not come in contact with the

liquid crystal and handle with care.

•

Use the preset Color Setting.

Use non-interlaced signals.

Allow adequate ventilation around the monitor, so that heat

can properly dissipate. Do not block ventilated openings or

place the monitor near a radiator or other heat sources.

Do not put anything on top of the monitor.

Do not use primary color blue on a dark background, as

it is difﬁcult to see and may produce eye fatigue due to

insufﬁcient contrast.

•

The power cable connector is the primary means of detaching

the system from the power supply. The monitor should be

installed close to a power outlet, which is easily accessible.

Cleaning the LCD Panel

•

When the liquid crystal panel is dusty, please gently wipe

with a soft cloth.

Do not move or mount this product by hanging a rope or wire

to the backside handle.

Do not mount or secure this product by using the backside

handle. It may fall and cause personal injury.

•

Please do not rub the LCD panel with hard material.

Please do not apply pressure to the LCD surface.

Please do not use OA cleaner as it will cause deterioration or

discolor on the LCD surface.

•

Handle with care when transporting. Save packaging for

transporting.

Cleaning the Cabinet

If using the cooling fan continuously, it is recommended to

wipe holes clean a minimum of once a month.

•

Unplug the power supply

Please clean the holes of back cabinet to reject dirt and dust

at least once a year because of set reliability.

Gently wipe the cabinet with a soft cloth

To clean the cabinet, dampen the cloth with a neutral

detergent and water, wipe the cabinet and follow with a dry

cloth.

When using a LAN cable, do not connect to a peripheral

device with wiring that might have excessive voltage.

Do not use monitor under rapid temperature and humidity

change condition or avoid cold air from air-conditioning outlet

directly, as it may shorten the lifetime of the monitor or cause

condensation. If condensation happens, let the monitor stand

unplugged until there is no condensation.

NOTE: DO NOT clean with benzene thinner, alkaline detergent,

alcoholic system detergent, glass cleaner, wax, polish

cleaner, soap powder, or insecticide. Rubber or vinyl

should not be in contact with the cabinet for an extended

period of time. These types of ﬂuids and materials can

cause the paint to deteriorate, crack or peel.

Connecting to a TV*

•

Cable distribution system should be grounded (earthed) in

accordance with ANSI/NFPA 70, the National Electrical Code

(NEC), in particular Section 820.93, Grounding of Outer

Conductive Shield of a Coaxial Cable.

•

The screen of the coaxial cable is intended to be connected

to earth in the building installation.

* The product you purchased may not have this feature.

English-3

Contents

Your new MultiSync monitor box* should contain the following:

•

LCD monitor

Power cord*¹

•

Clamp x 1 (X464UN/X464UNV)/x 3 (X554UN/X554UNS)

Screw with washer (M4 x 10) x 1 (X464UN/X464UNV)/

x 3 (X554UN/X554UNS)

Thumbscrew for optional stand x 2*²

Video Signal Cable (DisplayPort cable)

LAN cable

•

CD-ROM

Setup Manual

Video Signal Cable

(DisplayPort cable)

Power Cord*¹

Screw with washer (M4 x 10)

x 1 (X464UN/X464UNV)/

x 3 (X554UN/X554UNS)

Clamp x 1 (X464UN/X464UNV)/

x 3 (X554UN/X554UNS)

LAN cable

Setup Manual

Thumbscrew for

optional stand x 2*²

CD-ROM

Setup Manual

Remember to save your original box and packing material to transport or ship the monitor.

Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than one

power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been approved by

and complies with the safety standard of your particular country.

Only for X554UN/X554UNS.

Options:

•

Wall mount

Tabletop Stand

Remote Control Kit (Remote control and sensor)

Over-frame Kit

English-4

Installation

This device cannot be used or installed without the Tabletop

Stand or other mounting accessory for support. For proper

installation it is strongly recommended to use a trained,

NEC authorized service person. Failure to follow NEC

standard mounting procedures could result in damage to the

equipment or injury to the user or installer. Product warranty

does not cover damage caused by improper installation.

Failure to follow these recommendations could result in

voiding the warranty.

Orientation

•

When using the display in the portrait position, the

monitor should be rotated clockwise so that the left side

is moved to the top, right side is moved to the bottom.

This will allow for proper ventilation and will extend the

lifetime of the monitor. Improper ventilation may shorten

the lifetime of the monitor.

Mounting

DO NOT mount the monitor yourself. Please ask dealer.

For proper installation it is strongly recommended to use

a trained, qualiﬁed technician. Please inspect the location

where the unit is to be mounted. Mounting on wall or ceiling

is the customer’s responsibility. Not all walls or ceilings are

capable of supporting the weight of the unit. Product warranty

does not cover damage caused by improper installation,

remodelling, or natural disasters. Failure to comply with these

recommendations could result in voiding the warranty.

DO NOT block ventilated openings with mounting

accessories or other accessories.

For NEC Qualiﬁed Personnel:

To ensure safe installation, use two or more brackets to

mount the unit. Mount the unit to at least two points on the

installation location.

Mounting location

•

The ceiling and wall must be strong enough to support the

monitor and mounting accessories.

Please note the following when mounting

on wall or ceiling

DO NOT install in locations where a door or gate can hit

the unit.

•

When using mounting accessories other than those that

are NEC approved, they must comply with the VESA-

compatible (FDMlv1) mounting method.

DO NOT install in areas where the unit will be subjected

to strong vibrations and dust.

DO NOT install near where the main power supply enters

the building.

•

NEC recommends mounting interfaces that comply with

UL1678 standard in North America.

Do not install in where people can easily grab and hang

onto the unit or the mounting apparatus.

Mounting

Bracket

X464UN/X464UNV:

NEC strongly recommends

Unit

No gap

When mounting in a recessed area, as in a wall, leave at

least 4 inches (100 mm) of space between the monitor

and the wall for proper ventilation.

using size M6 screws

No thread

4 mm

Washers

(10-12 mm + thickness

of bracket and washer in

length). If using screws

longer than 10-12 mm,

check the depth of the hole.

under

ꢀ 8.5 mm

Screw

•

Allow adequate ventilation or provide air conditioning

around the monitor, so that heat can properly dissipate

away from the unit and mounting apparatus.

10-12 mm (X464UN/X464UNV)

10-14 mm (X554UN/X554UNS)

Thickness

of bracket

and washers

(Recommended Fasten Force:

470 - 635N•cm). Bracket hole should be under ꢀ 8.5 mm.

Mounting on ceiling

•

Ensure that the ceiling is sturdy enough to support the

weight of the unit and the mounting apparatus over time,

against earthquakes, unexpected vibrations, and other

external forces.

•

X554UN/X554UNS: NEC strongly recommends using size

M6 screws (10-14 mm + thickness of bracket and washer

in length). If using screws longer than 10-14 mm, check

the depth of the hole. (Recommended Fasten Force:

470 - 635N•cm). Bracket hole should be under ꢀ 8.5 mm.

•

Be sure the unit is mounted to a solid structure within

the ceiling, such as a support beam. Secure the monitor

using bolts, spring lock washers, washer and nut.

Prior to mounting, inspect the installation location to

insure that it is strong enough to support the weight of the

unit so that the unit will be safe from harm.

DO NOT mount to areas that have no supporting internal

structure. DO NOT use wood screws or anchor screws for

mounting. DO NOT mount the unit to trim or to hanging

ﬁxtures.

•

Refer to the instructions included with the mounting

equipment for detailed information.

Make sure there is no gap between the monitor and the

bracket.

Maintenance

When used in a video wall conﬁguration for a longer

time, slight expansion of the displays may happen due

to temperature changes. Due to this it is recommended

that a one millimeter gap is kept between adjacent display

edges.

•

Periodically check for loose screws, gaps, distortions,

or other problems that may occur with the mounting

apparatus. If a problem is detected, please refer to

qualiﬁed personnel for service.

•

Regularly check the mounting location for signs of

damage or weakness that may occur over time.

English-5

3. Installing and removing optional table

top stand

Attaching Mounting Accessories

The monitor is designed for use with the VESA mounting

system. Use WM-46UN-L2 or WM-46UN-P for X464UN/

X464UNV, WM-55UN-L or WM-55UN-P for X554UN/

X554UNS.

CAUTION: Installing and removing the stand must be done

by two or more people.

To install, follow those instructions included with the stand or

mounting apparatus. Use only those devices recommended

by the manufacturer.

1. Attach Mounting Accessories

Be careful to avoid tipping monitor when attaching

accessories.

NOTE:

For X464UN/X464UNV, use ONLY thumbscrews

which are included with the optional table top

stand.

For X554UN/X554UNS, use ONLY thumbscrews

which are included in the monitor.

For NEC mounting accessory only

VESA Mounting Interface (M6)

When installing the LCD monitor stand, handle the unit with

care to avoid pinching your ﬁngers.

Optional table top stand

300 mm (X464UN/

X464UNV)

400 mm (X554UN/

X554UNS)

Table

Mounting accessories can be attached with the monitor in

the face down position. To avoid damaging the screen face,

place the protective sheet on the table underneath the LCD.

The protective sheet was wrapped around the LCD in the

original packaging. Make sure there is nothing on the table

that can damage the monitor.

Protective Sheet

NOTE:

Install the stand so the long end of the feet

face forward. Use the ST-322 for the X464UN/

X464UNV and the ST-5220 for the X554UN/

X554UNS.

When using mounting accessories other than NEC compliant

and approved, they must comply with the VESA-compatible

mounting method.

4. Ventilation Requirements

When mounting in an enclosed space or recessed area,

leave adequate room between the monitor and the enclosure

to allow heat to disperse, as shown below.

2. Using Option Board

1. Turn off the main power switch.

2. Remove the handle.*¹

3. Remove the attached slot cover by unscrewing the

installed screws (Figure 1).

4. Insert option board in to the monitor. Attach the slot cover

by using the removed screws.

5. Attach the handle.*¹

NOTE:

Please contact your supplier for available option

boards.

Do not apply excessive force to manipulate the

optional board before ﬁxing it with screws.

Allow adequate ventilation or provide air conditioning around

the monitor, so that heat can properly dissipate away from

the unit and mounting apparatus; especially when you use

monitors in multiple screen.

(Only for X464UN/X464UNV)

Figure 1

*1: Only for X464UN/X464UNV.

English-6

5. Prevent Tipping

When using the display with the optional table top stand

fasten the LCD to a wall using a cord or chain that can

support the weight of the monitor in order to prevent the

monitor from falling. Fasten the cord or chain to the monitor

using the provided clamps and screws.

For the X464UN/X464UNV, the clamps and screws are

included with the optional table top stand.

640 mm (X554UN/X554UNS)

100 mm (X464UN/X464UNV)

Screw Holes (X464UN/X464UNV)

Screw Holes (X554UN/X554UNS)

Cord or chain

Clamp

Screw (M4)

Before attaching the LCD monitor to the wall, make sure that

the wall can support the weight of the monitor.

Be sure to remove the cord or chain from the wall before

moving the LCD.

English-7

Parts Name and Functions

Control Panel

³ POWER button (

)

º EXIT button (EXIT)

Switches the power on/off. See also page 16.

Activates the OSD menu when the OSD menu is turned-off.

Acts as EXIT button within the OSD to move to previous

menu.

· MUTE button (MUTE)

Switches the audio mute ON/OFF.

¾ Remote control sensor and Power Indicator

» INPUT button (INPUT)

Receives the signal from the remote control (when using the

wireless remote control). See also page 11.

Acts as SET/POINT ZOOM button within OSD menu.

(Toggle switches between [DVI], [DPORT], [HDMI], [VGA] or

[Y/Pb/Pr], [SCART]*, [VIDEO]*, [S-VIDEO]*, [DPORT2]*,

[DPORT3]*, [HDMI2]*, [RGB/HV]* or [Y/Pb/Pr2]*). These are

available input only, shown as their factory preset name.

Glows green when the LCD monitor is in active mode*.

Glows red when the LCD is in POWER OFF mode.

Glows amber when the monitor is in Power Save Mode.

Green and Amber blink alternately while in Power Standby

mode with the “SCHEDULE SETTINGS” function enabled.

When a component failure is detected within the monitor, the

indicator will blink red.

¿ PLUS button (+)

Acts as (+) button to increase the adjustment with OSD menu.

Increases the audio output level when the OSD menu is

turned off.

* If “OFF” is selected in “POWER INDICATOR” (see page 25),

LED will not light when the LCD monitor is in active mode.

Control Key Lock Mode

´ MINUS button (-)

Acts as (-) button to decrease the adjustment with OSD menu.

Decreases the audio output level when the OSD menu is

turned off.

This control completely locks out access to all Control Key

functions. To activate the control key lock function, press

both and and hold down simultaneously for more than

3 seconds. To resume user mode, press both and and

hold simultaneously for more than 3 seconds.

² UP button (

Activates the OSD menu when the OSD menu is turned-off.

Acts as button to move the highlighted area up to select

adjustment items within OSD menu.

)

*: This function depends on which option board you use.

¶ DOWN button (

)

Activates the OSD menu when the OSD menu is turned-off.

Acts as button to move the highlighted area down to select

adjustment items within OSD menu.

English-8

Terminal Panel

Option control unit

From Option control unit

³ AC IN connector

¸ DisplayPort connectors

Connects with the supplied power cord.

IN connector: To input DisplayPort signals.

OUT connector: To output signal which is displayed.

See page 25 VIDEO OUT SETTING.

To output signal which is displayed as a main picture when

selected PIP mode. See page 11.

· Main Power Switch

On/Off switch to turn main power ON/OFF.

» EXTERNAL SPEAKER TERMINAL

¹ HDMI IN

To input digital HDMI signals.

To output the audio signal from AUDIO 1, DPORT and HDMI.

Red terminal is plus (+).

Black terminal is minus (-).

NOTE: This speaker terminal is for 15 W + 15 W (8 ohm) speaker.

Ƹ DVI IN (DVI-D)

To input digital RGB signals from a computer or HDTV device

having a digital RGB output.

* This connector does not support analog input.

¿ AUDIO OUT

To output the audio signal from the AUDIO IN 1, 2, DPORT and

HDMI to an external device (stereo receiver, ampliﬁer, etc.).

ƹ Option board slot

Slot 2 and slot 3 type accessories are available.

Please contact your supplier for detailed information.

NOTE: Please contact your supplier for available option board.

´ Service port

This USB slot is for future software upgrades.

² LAN port (RJ-45)

LAN connection. See page 31 and 34.

NOTE: Please give priority for use to LAN1.

ƺ Remote control sensor, AMBIENT LIGHT SENSOR

and HUMAN SENSOR

Receives the signal from the Remote control.

Detects the level of ambient light, allowing the monitor to

make automatic adjustments to the brightness setting,

resulting in a more comfortable viewing experience.

Do not cover this sensor. See page 19.

¶ AUDIO IN 1, 2

To input audio signal from external equipment such as a

computer or DVD player.

Detects human presence in front of the monitor. See page 45.

ᕨ RS-232C (D-Sub 9 pin)

Connect RS-232C input from external equipment such as a PC

in order to control RS-232C functions.

ƻ Kensington Lock

For security and theft prevention.

¾ REMOTE IN

Ƽ Intelligent wireless data sensor

Use the optional wired remote control by connecting it to your

monitor.

Sensor for wireless communication of the monitor information

and settings.

NOTE: Do not use this connector unless speciﬁed.

µVGA IN (mini D-Sub 15 pin)

To input analog RGB signals from a personal computer or

from other RGB equipment. This input can be used with an

RGB or COMPONENT source. Please select signal type in

TERMINAL SETTING. See page 27.

NOTE: When you use this connector for COMPONENT,

please use a suitable signal cable. If you have any questions,

please ask your dealer.

English-9

Wireless Remote Control (Optional)

´ AUDIO INPUT button

Selects audio input source [IN1], [IN2], [IN3]*², [OPTION]*²,

[HDMI], [DPORT], [HDMI2]*², [DPORT2]*², [DPORT3]*².

² OPTION MENU button*¹

¶ KEYPAD

Press buttons to set and change passwords, change channel

and set REMOTE ID.

º ENT button*¹

¾ DISPLAY button

Turns on/off the information OSD. See page 18.

µ MENU button

Turns on/off the menu mode.

¸ AUTO SET UP button

Enters auto setup menu. See page 20.

¹ EXIT button

Returns to previous menu within OSD menu.

Ƹ UP/DOWN button (

)

Acts as button to move the highlighted area up or down

to select adjustment items within OSD menu.

Small screen which adjusted “PIP” mode moves up or down.

ƹ MINUS/PLUS (-/+) button

Increases or decreases the adjustment level within OSD

menu settings.

Small screen which adjusted “PIP” mode moves left or right

and increases or decreases the size.

³ POWER button

Switches the power on/standby.

· INPUT button

ƺ SET/POINT ZOOM button

Selects input signal.

Makes selection. Activates POINT ZOOM function when OSD

menu is not shown.

DVI: DVI

HDMI: HDMI, HDMI2*²

DisplayPort: DPORT, DPORT2*², DPORT3*²

VGA: VGA

ƻVOLUME UP/DOWN button (VOL +/-)

Increases or decreases audio output level.

Y/Pb/Pr: Y/Pb/Pr, SCART*², Y/Pb/Pr2*²

RGB/HV*²: RGB/HV

Ƽ CH/ZOOM UP/DOWN button (CH/ZOOM +/-)*¹

Increases or decreases POINT ZOOM level.

VIDEO*²: VIDEO, S-VIDEO

OPTION: Depends on your connection

ƽ GUIDE button*¹

» PICTURE MODE button

Selects picture mode, [HIGHBRIGHT], [STANDARD],

[sRGB], [CINEMA], [CUSTOM1], [CUSTOM2]. See page 18.

ƾ MUTE button

Turns on/off mute function.

HIGHBRIGHT: for moving images such as DVD.

STANDARD: for images.

sRGB: for text based images.

CINEMA: for movies.

CUSTOM1 and CUSTOM2: activate auto dimming

function. See page 28.

ƿ STILL button

ON/OFF button: Activates/deactivates still picture mode.

STILL CAPTURE button: Captures still picture.

NOTE: This function is released when activating IMAGE

FLIP.

IMAGE FLIP button

¿ ASPECT button

Toggle switches between H FLIP, V FLIP, 180° ROTATE and

NONE. See page 21.

Selects picture aspect, [FULL], [WIDE], [DYNAMIC], [1:1],

[ZOOM] and [NORMAL]. See page 17.

English-10

PIP (Picture In Picture) button

Operating Range for the Optional

Remote Control

ON/OFF button: Toggle switches between PIP, POP,

PICTURE BY PICTURE-ASPECT and PICTURE BY

PICTURE-FULL. See page 22.

INPUT button: Selects the “picture in picture” input signal.

CHANGE button: Replaces to the main picture and sub

picture.

NOTE: Enable to change the sub picture size by pressing

SET/POINT ZOOM button during PIP mode.

Sub picture

Point the top of the remote control toward the sensor unit’s

remote control sensor in optional control kit during button

operation.

Use the remote control within a distance of about 7 m (23 ft.)

from remote control sensor or at a horizontal and vertical

angle of within 30° within a distance of about 3.5 m (10 ft.).

Main picture Connector

DP Out*⁵

DPORT*³

DVI

Yes

HDMI

Yes

VGA

Yes

Y/Pb/Pr

Yes

OPTION

Yes

DPORT

DVI

DisplayPort

DVI-D

DPORT

Yes

DVI

HDMI

Yes

HDMI 1

VGA

Yes

D-Sub*⁴

Y/Pb/Pr

OPTION

Yes

Option

Yes

OPTION

*3: When VIDEO OUT SETTING is ONN, DPORT ccannot bbe selectted as thhe sub piicture.

*4: If VGA or Y/Pb/Pr is selected as the main picture, DP out iss disabbled eveen when

VIDEO OUT SETTTING is ON.

*5: DP out can output signal only when VIDEO OUT SETTTING iis ON.

REMOTE ID button

Caution: Important, the remote control

system may not function

Activates REMOTE ID function.

when direct sunlight or strong

illumination strikes the remote

control sensor or when there is

an object in the path.

MTS button*¹

button*¹

Activates closed captioning.

NOTE: VIDEO*², S-VIDEO*²inputs only.

*1: This button’s action depends on which option board you use.

Refer to the option board’s manual for further information.

Handling the remote control

*2: This function depends on which option board you use.

•

Do not subject to strong shock.

Do not allow water or other liquid to splash the remote

control. If the remote control gets wet, wipe it dry

immediately.

•

Avoid exposure to heat and steam.

Other than to install the batteries, do not open the remote

control.

English-11

Setup

NEC recommends the following battery use:

1. Determine the installation location

CAUTION: Installing your LCD monitor must be done by a

qualiﬁed technician. Contact your dealer for more

information.

•

Place “AAA” size batteries matching the (+) and (-) signs

on each battery to the (+) and (-) signs of the battery

compartment.

•

Do not mix battery brands.

CAUTION: MOVING OR INSTALLING THE LCD MONITOR

MUST BE DONE BY TWO OR MORE PEOPLE.

Failure to follow this caution may result in injury if

the LCD monitor falls.

Do not combine new and old batteries. This can shorten

battery life or cause liquid leakage of batteries.

•

Remove dead batteries immediately to prevent battery

acid from leaking into the battery compartment.

CAUTION: Do not mount or operate the monitor upside

•

Do not touch exposed battery acid, it may injure skin.

down, face up or face down.

NOTE:

If you do not intend to use the Remote Control for

a long period of time, remove the batteries.

CAUTION: This LCD has a temperature sensor and cooling

fan, including a fan for the option board.

If the LCD becomes too hot, the cooling fan will

turn on automatically.

3. Connect external equipment

(See pages 14 and 15)

The option board’s fan is active although the

temperature is lower than normal operating

temperature for cooling the option board. If the

LCD becomes overheated while the cooling fan

is running, a “Caution” warning will appear. If the

“Caution” warning appears, discontinue use and

allow the unit to cool. Using the cooling fan will

reduce the likelihood of early circuit failure and

may help reduce image degradation and “Image

Persistance”.

If the LCD is used in an enclosed area or if the

LCD panel is covered with a protective screen,

please check the inside temperature of the

monitor by using the “HEAT STATUS” control

in the OSD (see page 25). If the temperature is

higher than the normal operating temperature,

please turn the cooling fan to ON within the FAN

CONTROL menu within the OSD (see page 25).

•

To protect the external equipment; turn off the main power

before making connections.

•

Refer to your equipment user manual for further

information.

NOTE:

Do not connect/disconnect cables when turning

on the monitor or other external equipment as this

may result in a loss of the monitor image.

4. Connect the supplied power cord

•

The equipment should be installed close to an easily

accessible power outlet.

Please fasten power cord to the LCD monitor by attaching

the screw and clamp.

Fully insert the prongs into the power outlet socket.

A loose connection may cause image degradation.

NOTE:

Please refer to the “Safety Precautions and

Maintenance” section of this manual for proper

selection of AC power cord.

IMPORTANT: Lay the protective sheet, which was wrapped

around the LCD monitor when it was

packaged, beneath the LCD monitor so as not

to scratch the panel.

2. Install the remote control (Optional)

batteries

The remote control is powered by two 1.5V AAA batteries.

To install or replace batteries:

Screw

Clamp

A. Press and slide to open the cover.

B. Align the batteries according to the (+) and (–) indications

inside the case.

C. Replace the cover.

CAUTION: Incorrect usage of batteries can result in leaks or

bursting.

English-12

5. Switch on the power of all the attached

external equipment

When connected with a computer, switch on the power of the

computer ﬁrst.

6. Operate the attached external equipment

Display the signal from the desired input source.

7. Adjust the sound

Make volume adjustments when required.

8. Adjust the screen (See pages 20 and 21)

Make adjustments of the screen display position when

necessary.

9. Adjust the image (See page 20)

Make adjustments such as backlight or contrast when

required.

10. Recommended Adjustments

To reduce the risk of the “Image Persistence”, please adjust

the following items based on the application being used:

“SCREEN SAVER”, “SIDE BORDER COLOR” (See page 25)

“DATE & TIME”, “SCHEDULE SETTINGS” (See page 22).

It is recommended that the “FAN CONTROL” setting

(See page 25) be turned to ON also.

English-13

Connections

NOTE:

Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a

loss of the monitor image.

NOTE:

Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.

Before making connections:

First turn off the power of all the attached equipment and make connections.

Refer to the user manual included with each separate piece of equipment.

Wiring Diagram

DVD Player

Second monitor*

Solid lines = video signal

Dotted lines = audio signal

Stereo Ampliﬁer

Computer (Analog)

*: Multiple monitors that are daisy-chained have a limit to the connectable monitors.

Computer (Digital)

Connected

equipment

Connecting

terminal

DisplayPort

DVI (DVI-D)

HDMI

VGA (D-Sub)

Option

DisplayPort

DVI (DVI-D)

HDMI

Connecting

audio terminal

DPORT

AUDIO IN1/IN2

HDMI

AUDIO IN1/IN2

OPTION

DPORT

AUDIO IN1/IN2

HDMI

Input button

Setting in terminal mode

Input signal name

in remote control

DisplayPort

DVI

HDMI

DVI-HD

RAW/EXPAND*¹

HDMI

RGB/HV

Y/Pb/Pr

OPTION

DisplayPort

DVI

D-SUB MODE RGB

D-SUB MODE COMPONENT

VGA

COMPONENT

OPTION

DVI-PC

DVI

HDMI

RAW/EXPAND*¹

HDMI

VGA (D-Sub)

Option

VGA

OPTION

AUDIO IN1/IN2

OPTION

RGB/HV

OPTION

*1: depend on signal type.

English-14

Connecting a Personal Computer

Connecting your computer to your LCD monitor will enable you to display your computer’s screen image.

Some video cards may not display an image correctly.

Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically.

Scanning frequency

Horizontal Vertical

Remarks

Resolution

640 x 480

800 x 600

31.5 kHz

37.9 kHz

48.4 kHz

48 kHz

60 Hz

1024 x 768

1280 x 768

1360 x 768

1280 x 1024

1600 x 1200

1920 x 1080

48 kHz

64 kHz

75 kHz

Compressed image

67.5 kHz

Recommended resolution

•

If you use with a Macintosh PowerBook, set “Mirroring” to Off on your PowerBook.

Refer to your Macintosh’s owner’s manual for more information about your computer’s video output requirements and any

special identiﬁcation or conﬁguration your monitor’s image and monitor may require.

•

Input TMDS signals conforming to DVI standards.

To maintain display quality, use a cable that conforms to DVI standards.

Connecting a DVD Player or Computer with HDMI out

•

Please use an HDMI cable with HDMI logo.

It may take a moment for the signal to appear.

Some video cards or drivers may not display an image correctly.

When you use a computer with HDMI out, please set OVER SCAN to “OFF” (see page 27).

Connecting a Computer with DisplayPort

•

Please use DisplayPort cable with DisplayPort compliance logo.

It may take a moment for the signal to appear.

Please note that when connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not

appear.

•

Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.

English-15

Basic Operation

Power ON and OFF Modes

The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off.

NOTE:

The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the

Power Button.

OFF

Main Power Switch

Power Button

Using the optional remote control

English-16

Power Indicator

Picture Aspect

DVI, VGA, RGV/HV*⁴, DPORT, DPORT2*⁴, DPORT3*⁴

Mode

Status Indicator Light

Green*¹

FULL

1:1

ZOOM

NORMAL

Power ON

Power OFF and Power Save “AUTO Red

POWER STANDBY”

HDMI, Y/Pb/Pr, SCART*⁴, VIDEO*⁴, S-VIDEO*⁴, HDMI2*⁴, Y/Pb/Pr2*⁴

Power consumption under 0.5 W

FULL

WIDE

DYNAMIC

1:1

ZOOM

NORMAL

Power Save “AUTO POWER SAVE” Amber

Power consumption under 2.5 W*²

Aspect ratio

of image

Recommended selection

for picture aspect*³

Power Standby when “SCHEDULE

SETTINGS” enabled

Diagnosis (Detecting failure)

Green and Amber blink alternately

Unchanged view*³

Red Blinking

(See Troubleshooting page 46)

NORMAL

*1 If “OFF” is selected in POWER INDICATOR (page 25), the LED will not light when the

LCD monitor is in active mode.

*2 Without any option, with factory settings.

4:3

DYNAMIC

FULL

Using Power Management

The LCD monitor follows the VESA approved DPM Display

Power Management function.

The power management function is an energy saving

function that automatically reduces the power consumption

of the display when the keyboard or the mouse has not been

used for a ﬁxed period.

The power management feature on your new display has

been set to the “AUTO POWER SAVE” mode. This allows

your display to enter a Power Saving Mode when no signal is

applied. This could potentially increase the life and decrease

the power consumption of the display.

Squeeze

Letterbox

WIDE

*³Grey areas indicate unused portions of the screen.

NORMAL: Displays the aspect ratio the same as it is sent

from the source.

NOTE:

Depending on the PC and video card used, this

function may not operate.

FULL: Fills entire screen.

NOTE:

The monitor automatically goes into OFF at the

preset time period after signal is lost.

WIDE: Expands a 16:9 letter box signal to ﬁll entire screen.

DYNAMIC: Expands a 4:3 pictures to ﬁll the entire screen

with non-linearity. Some of the outside image area will be cut

off due to expansion.

Selecting a video source*⁴

To view a video source:

Use the input button to set [VIDEO], [S-VIDEO].

1:1: Displays the image in a 1 by 1 pixel format.

ZOOM

Use the COLOR SYSTEM menu to set [AUTO], [NTSC],

[PAL], [SECAM], [PAL60], [4.43NTSC], according to your

video format.

The image can be expanded beyond the active display area.

The image which is outside of active display area is not

shown.

ZOOM

*4: This function depends on which option board you use.

English-17

Information OSD

The Information OSD provides information such as: Input Source, Picture Size, etc.

Press the DISPLAY button on the remote to bring up the Information OSD.

ᕥ

Input Name

Audio input mode

Picture aspect

Input Signal Information

Sub picture information

Picture Mode

DVI, VGA, RGB/HV*, DPORT, DPORT2*, DPORT3*

STANDARD

sRGB

CUSTOM1

CUSTOM2

HIGHBRIGHT

HDMI, Y/Pb/Pr, SCART*, VIDEO*, S-VIDEO*, HDMI2*, Y/Pb/Pr2*

STANDARD

CINEMA

CUSTOM1

CUSTOM2

HIGHBRIGHT

*: This function depends on which option board you use.

English-18

OSD (On-Screen-Display) Controls

NOTE:

Some functions may not be available depending on the model or optional equipment.

Input source

Main Menu Icons

Main Menu Item

Adjustment Settings

Sub Menu

THANK YOU FOR SAVING

THE ENVIRONMENT.

CARBON FOOTPRINT

86.0 %

PICTURE MODE

Goto Adjustment Return

Select

Key Guide

Press UP or DOWN

button to select

sub-menu.

Press SET/POINT

ZOOM.

Press UP or DOWN,

PLUS or MINUS to select

the function or setting to

be adjusted.

Press MENU or EXIT.

Remote Control

Press UP or DOWN

button to select.

Press INPUT button

to decide.

Press UP or DOWN, PLUS

or MINUS button to select.

Press EXIT

Control Panel

OSD screen

English-19

Setting

Default

PICTURE

BACKLIGHT

Adjusts the overall image and background brightness. Press + or - to adjust.

NOTE: When MODE1 or MODE2 is selected in ROOM LIGHT SENSING, this function cannot be

changed.

CONTRAST

Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.

NOTE: When sRGB is selected in picture mode, this function cannot be changed.

SHARPNESS

BRIGHTNESS

Adjusts the crispness of the image. Press + or - to adjust.

50*²

Adjusts the image brightness in relationship to the background. Press + or - to adjust.

NOTE: When sRGB is selected in picture mode, this function cannot be changed.

HUE

Adjusts the hue of the screen. Press + or - to adjust.

NOTE: When sRGB is selected in picture mode, this function cannot be changed.

COLOR

Adjusts the color depth of the screen. Press + or - to adjust.

50*²

NOTE: When sRGB is selected in picture mode, this function cannot be changed.

COLOR TEMPERATURE

Adjusts the color temperature of the entire screen. A low color temperature will make the screen

reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further

adjustment, the individual R/G/B/ levels of the white point can be adjusted. To adjust the R/G/B

levels, CUSTOM must be showing as the COLOR TEMP selection.

10000K

NOTE: When sRGB is selected in picture mode, predeﬁned 6500k is set so it cannot be changed.

When PROGRAMMABLE1, PROGRAMMABLE2 or PROGRAMMABLE3 is selected in GAMMA

CORRECTION, this function cannot be changed.

COLOR CONTROL

Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.

NOTE: When sRGB is selected in picture mode, this function cannot be changed.

When INPUT2 of SUPER is selected in INPUT CHANGE and displayed, this function cannot be

changed.

GAMMA CORRECTION

Select a display gamma for best picture quality.

NOTE: When sRGB is selected in picture mode, this function cannot be changed.

PROGRAMMABLE1

(except sRGB

setting)

NATIVE

2.2

Gamma correction is handled by the LCD panel.

Typical display gamma for use with a PC.

Good for video (DVD, etc.)

2.4

S GAMMA

Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the

image (S-Curve).

DICOM SIM.

DICOM GSDF curve simulated for LCD type.

PROGRAMMABLE1, 2, 3 A programmable gamma curve can be loaded using NEC optional software.

MOVIE SETTINGS

NOTE: When INPUT2 of SUPER is selected in INPUT CHANGE and displayed, this function

cannot be changed.

NOISE REDUCTION*¹Adjusts the amount of noise reduction. Press + or - to adjust.

0*²

VIDEO, S-VIDEO inputs only

TELECINE

Automatically senses the sources frame rate for optimal picture quality.

AUTO*²

HDMI, Y/Pb/Pr, SCART*¹, VIDEO*¹,

S-VIDEO*¹, HDMI2*¹, Y/Pb/Pr2*¹inputs only

ADAPTIVE CONTRAST Sets the level of adjustment for dynamic contrast.

S-VIDEO*¹, HDMI2*¹, Y/Pb/Pr2*¹inputs only

OFF

HDMI, Y/Pb/Pr, SCART*¹, VIDEO*¹,

PICTURE MODE

RESET

Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [CUSTOM1] or

[CUSTOM2]. See page 18.

STANDARD

Resets the following settings within the PICTURE menu back to factory setting: BACKLIGHT,

CONTRAST, SHARPNESS, BRIGHTNESS, HUE, COLOR, COLOR TEMPERATURE,

COLOR CONTROL, GAMMA CORRECTION, MOVIE SETTINGS.

ADJUST

AUTO SETUP

Automatically adjusts Screen Size, H position, V position, Clock, Phase and White Level.

H Position, V Position and Phase are adjusted automatically when new timing is detected.

OFF

VGA, RGB/HV*¹inputs only

AUTO ADJUST

VGA, RGB/HV*¹inputs only

H POSITION

Controls the horizontal position of the image within the Display area of the LCD.

Press + to move right. Press - to move left.

All inputs except DVI, HDMI, DPORT

V POSITION

Controls the vertical position of the image within the Display area of the LCD.

Press + to move up. Press - to move down.

All inputs except DVI, HDMI, DPORT

CLOCK

Press + to expand the width of the image on the right of the screen.

Press - to narrow the width of the image on the left.

VGA, RGB/HV*¹inputs only

*1: This function depends on which option board you use.

*2: Depends on signal input.

English-20

PHASE

Adjusts the visual “noise” on the image.

VGA, RGB/HV*¹, Y/Pb/Pr, SCART*¹, Y/Pb/Pr2*¹

inputs only

H RESOLUTION

Adjusts the horizontal size of the image.

Adjusts the vertical size of the image.

VGA, RGB/HV*¹inputs only

V RESOLUTION

VGA, RGB/HV*¹inputs only

INPUT RESOLUTION

If there is a problem with signal detection, this function forces the monitor to display the signal at

the desired resolution. After selection, execute “AUTO SETUP” if required.

If no problem is detected, the only available option will be “AUTO”.

AUTO

VGA, RGB/HV*¹inputs only

ASPECT

Select the aspect ratio of the screen image.

FULL

NOTE: When the ASPECT is DYNAMIC, WIDE or ZOOM, the image will be changed FULL

image before IMAGE FLIP, then start to IMAGE FLIP.

When the ASPECT is DYNAMIC or ZOOM, the image will be changed FULL image before TILE

MATRIX, then start to TILE MATRIX. After TILE MATRIX, the ASPECT will be returned previous

ASPECT or set ASPECT during TILE MATRIX.

When the ASPECT is DYNAMIC or ZOOM, the image will be changed FULL image before POINT

ZOOM, then start to POINT ZOOM. After POINT ZOOM, the ASPECT will be returned previous

ASPECT. When the ASPECT is changed during POINT ZOOM, DYNAMIC and ZOOM will be

FULL image.

NORMAL

FULL

Displays the aspect ratio the same as it is sent from the source.

Fills entire screen.

WIDE

Expands a 16:9 letter box signal to ﬁll entire screen.

DYNAMIC

Expands a 4:3 pictures to ﬁll the entire screen with non-linearity. Some of the outside image area

will be cut off due to expansion. TILE MATRIX becomes invalid.

1:1

Display the image in a 1 by 1 pixel format. (If the input resolution is higher than a 1920 x 1080

resolution, the image will be scaled down to ﬁt the screen). TILE MATRIX becomes invalid.

ZOOM

The image can be expanded/reduced.

NOTE: The expanded image which is outside of active display area is not shown. The reduced

image may have some image degradation.

ZOOM

HZOOM

Maintains the aspect ratio while zooming.

Amount of horizontal zoom.

Amount of vertical zoom.

Horizontal position.

VZOOM

H POS

V POS

Vertical position.

IMAGE FLIP

NOTE: OVER SCAN is disabled when IMAGE FLIP is selected.

When the ASPECT is DYNAMIC, WIDE or ZOOM, the image will be changed FULL image before

IMAGE FLIP, then start to IMAGE FLIP.

When selecting IMAGE FLIP except for NONE, following functions are released: PIP MODE,

TILE MATRIX, SUPER in INPUT CHANGE, STILL, POINT ZOOM.

IMAGE FLIP

Display the inverse image right-left, up-down or rotation.

Press + or - to select.

NONE

H FLIP

Normal mode.

The image inverts right-left.

The image inverts up-down.

The image rotates 180 degrees.

V FLIP

180° ROTATE

OSD FLIP

Determines the OSD display direction.

OFF

If “ON” is selected, OSD will invert depending on the image.

RESET

Resets “ADJUST” settings back to factory settings.

AUDIO

VOLUME

BALANCE

Increases or decreases output volume level.

Select “STEREO” or “MONO” of audio output.

CENTER,

STEREO

If you select “STEREO”, adjust the balance of L/R volume.

Press + button to move the stereo sound image to right.

Press - button to move the stereo sound image to left.

TREBLE

To accentuate or reduce the high frequency sound.

Press + button to increase TREBLE sound.

Press - button to decrease TREBLE sound.

*1: This function depends on which option board you use.

English-21

BASS

To accentuate or reduce the low frequency sound.

Press + button to increase BASS sound.

Press - button to decrease BASS sound.

SURROUND

Artiﬁcial surround sound.

OFF

NOTE: Audio out is disabled when this function is set to ON.

PIP AUDIO

LINE OUT

Selects source of PIP audio.

MAIN AUDIO

FIXED

Selecting “VARIABLE” enables control of the line out level with the VOLUME button.

NOTE: Audio out is disabled when this function is set to ON.

AUDIO INPUT

AUDIO DELAY

RESET

Selects audio input source [IN1], [IN2], [IN3]*¹, [OPTION]*¹, [HDMI], [DPORT], [HDMI2]*¹,

[DPORT2]*¹, [DPORT3]*¹.

Depend on

signal input

Enables to set the delay time to output the audio. DELAY TIME can be set between 0 and

100 milliseconds. “ON” activates this function.

ON,

37 MSEC.

Resets “AUDIO” options back to factory settings except VOLUME.

SCHEDULE

OFF TIMER

Sets the monitor to power off after a length of time.

A time between 1 to 24 hours is available.

OFF

SCHEDULE SETTINGS

SCHEDULE LIST

DATE & TIME

Creates a working schedule for the monitor to use.

List of schedules.

Sets the date, time, and daylight saving region. Date & time must be set in order for the

“SCHEDULE” function to operate. See page 29.

YEAR

MONTH

Conﬁgures the year for the real-time clock.

Conﬁgures the month for the real-time clock.

Conﬁgures the day for the real-time clock.

Conﬁgures the time for the real-time clock.

Conﬁgures daylight savings on or off.

DAY

TIME

OFF

DAYLIGHT SAVING

RESET

Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER,

SCHEDULE SETTINGS.

PIP

KEEP PIP MODE

Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off.

When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.

OFF

PIP MODE

Selects Picture-in-Picture mode.

NOTE: This function is released when selecting IMAGE FLIP except for NONE.

OFF

PIP

Normal mode.

Picture in Picture mode.

Picture out Picture mode.

POP

PICTURE BY PICTURE- Picture by picture (split screen) mode, with keep aspect.

ASPECT

PICTURE BY PICTURE

FULL

Picture by picture (split screen) mode, with full screen.

SUB INPUT

Selects sub picture input signal.

Depends on

signal input

PIP SIZE

Determines the size of the sub-picture used in Picture-in-Picture (PIP) mode.

Press the SET/POINT ZOOM button to adjust. Press + or CH+ to expand. Press - or CH- to

reduce.

It is also possible to change the sub-picture size by pressing the SET/POINT ZOOM button when

the sub-picture is shown.

PIP POSITION

ASPECT

Determines the location where the PIP appears on the screen.

X = 95, Y = 92

FULL

Selects sub picture aspect, [FULL], [NORMAL] and [WIDE]. See page 17.

TEXT TICKER

MODE

OFF

Enables Text Ticker and allows you to set Horizontal or Vertical direction.

Selects the location of the Text Ticker on the screen.

POSITION

SIZE

Determines the size of the Text Ticker in relationship to the overall screen size.

*1: This function depends on which option board you use.

English-22

BLEND

Sets the transparency of the Text Ticker (0: transparent, 100: opaque).

Enables auto-detection of the Text Ticker.

DETECT

FADE IN

Enables fade-in of the text ticker.

RESET

Resets PIP options back to factory settings except SUB INPUT and ASPECT.

OSD

LANGUAGE

ENGLISH

DEUTSCH

FRANÇAIS

ITALIANO

ESPAÑOL

SVENSKA

РУССКИЙ

Select the language used by the OSD.

ENGLISH

(Depends on

destination)

MENU DISPLAY TIME

OSD POSITION

Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.

Determines the location where the OSD appears on the screen.

30 SEC.

X = 128, Y = 225

DOWN

RIGHT

LEFT

INFORMATION OSD

Selects whether the information OSD is displayed or not. The information OSD will be displayed

when the input signal or source changes. The information OSD will also give a warning when

there is no-signal or the signal is out-of range.

ON, 3 SEC.

An interval between 3 to 10 seconds for the Information OSD to appear is available.

MONITOR INFORMATION Indicates the model and serial number of your monitor and ﬁrmware version.

CARBON SAVINGS: Display the estimated carbon saving information in kg-CO2. The carbon

footprint factor in the carbon saving calculation is based on the OECD (2008 Edition).

CARBON USAGE: Display the estimated carbon usage information in kg-CO2. This is the

arithmetic estimation, not actual measurement value. This estimation is based without any

options.

OSD TRANSPARENCY

OSD ROTATION

LANDSCAPE

Set the transparency of the OSD.

OFF

Determines the OSD display direction between landscape and portrait.

Display the OSD with landscape mode.

LANDSCAPE

PORTRAIT

Display the OSD with portrait mode.

INPUT NAME

You can create a name for the INPUT currently being used.

Max: 8 characters, including Space, A-Z, 0-9, and some symbols.

MEMO

RESET

Sets a title and message via HTTP server. See page 42.

Resets the following settings within the OSD menu back to factory setting:

MENU DISPLAY TIME, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY.

MULTI DISPLAY

ID CONTROL

Sets the monitor ID number from 1-100 and group ID from A-J. DETECTED MONITORS shows

the number of all monitors which follow in the chain with LAN.

NOTE: Group ID is made of multiple selections.

AUTO ID

When “YES” is selected, monitor ID numbers are set automatically in all monitors which follow in

the chain with LAN.

NOTE: All monitors which follow in the chain with LAN should be ON. When executing this

function while in standby mode or power save mode, “LAN POWER” should be ON.

AUTO ID RESET

Resets monitor ID number of all monitors which follow in the chain with LAN.

NOTE: AUTO ID RESET should be done when changes the number of monitors which follow in

the chain with LAN.

English-23

IR LOCK SETTINGS

Prevents the monitor from being controlled by the wireless remote control.

When ACTIVATE is selected, all the settings are activated.

UNLOCK

NOTE: IR LOCK SETTINGS is a function intended only to the wireless remote control buttons.

This function does not lock out access to all buttons at the back of the monitor. To return to

normal operation, press the “DISPLAY” button on the remote control for 5 seconds.

MODE SELECT

UNLOCK

Selects the mode UNLOCK, ALL LOCK or CUSTOM LOCK.

All buttons on the remote control are available for normal operations.

Locks all remote control buttons.

ALL LOCK

CUSTOM LOCK

Selects which buttons to be locked from POWER, VOLUME, and INPUT button.

Except for CUSTOM LOCK settings, other buttons on the remote control are locked.

POWER: When LOCK is selected, POWER button is locked.

VOLUME: When UNLOCK is selected, sets minimum and maximum volume between VOL.0 to

VOL.100.

VOLUME (+) button and VOLUME (-) buttons are only available from the minimum

volume to the maximum volume you set.

When LOCK is selected, VOLUME (+) button and VOLUME (-) buttons are locked.

INPUT:

When UNLOCK is selected, choose up to three buttons from DVI, DisplayPort, VGA,

HDMI, Y/Pb/Pr, VIDEO*¹, S-VIDEO*¹, OPTION*¹which you prefer to be unlocked.

The unselected buttons are locked. When LOCK is selected, all INPUT buttons are

locked.

TILE MATRIX

Allows one image to be expanded and displayed over multiple screens (up to 100) through a

distribution ampliﬁer.

NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate

without a distribution ampliﬁer at a lower number of screens.

This function is released when selecting IMAGE FLIP except for NONE.

When “DYNAMIC” or “ZOOM” is selected in ASPECT while executing TILE MATRIX, the setting

will be applied after completing of TILE MATRIX.

H MONITORS

V MONITORS

POSITION

Number of monitors arranged horizontally.

Number of monitors arranged vertically.

Select which section of the tiled image to be displayed on the monitor.

Turns the TILE COMP feature on.

TILE COMP

NONE

TILE MATRIX ENABLE Enables Tile Matrix.

FRAME COMP

Sets the tiled image timing to be displayed on the monitor. Large number makes large inﬂuence

to displayed image.

NOTE: If FRAME COMP is set to AUTO or MANUAL, V SCAN REVERSE is not available.

The image may be distorted when turning the power on or changing the settings.

NONE

FRAME COMP is not available.

AUTO

Sets display timing to vertical direction of all monitors automatically.

Sets display timing to individual monitor.

MANUAL

V SCAN REVERSE*²

Reverse scanning image direction. Normal scanning direction is top to bottom.

NONE

NOTE: If V SCAN REVERSE is set to AUTO or MANUAL, FRAME COMP is not available.

NONE

AUTO

V SCAN REVERSE is not available.

Sets automatically calculated image scanning direction to all monitors.

Sets scanning direction to individual monitor.

MANUAL

NON REVERSE

REVERSE

Sets normal scanning direction and delays 1 frame display image timing.

Reverse scanning direction to individual monitor.

TILE MATRIX MEM

When “INPUT” is selected, TILE MATRIX setting is applied to each signal input.

COMMON

AUTO TILE MATRIX

SETUP

Allows auto setting of multiple screens by inputting the number of monitors arranged horizontally DEACTIVATE

and vertically on the primary monitor. Following settings are set automatically: MONITOR

ID, TILE MATRIX, TILE MATRIX MEM, Input Signal, VIDEO OUT SETTING, DisplayPort in

TERMINAL SETTING.

NOTE: All monitors which follow in the chain with LAN should be ON. When executing this

function while in standby mode or power save mode, “LAN POWER” should be set to ON.

AUTO ID will be automatically executed. When you use this function, it is recommended that

monitors are chained by DisplayPort cable.

Example of installation via LAN:

Primary monitor

H MONITORS

V MONITORS

*1: This function depends on which option board you use.

*2: Except for X554UNS.

English-24

POWER ON DELAY

DELAY TIME

Adjusts the delay time between being in “standby” mode and entering “power on” mode.

“POWER ON DELAY” can be set between 0 and 50 seconds.

0 SEC.

OFF

LINK TO ID

When “ON” selected, delay time is linked with Monitor ID. It takes more time as larger ID number.

VIDEO OUT SETTING

Enables the signal output from DPORT. See also page 27 “DisplayPort” in TERMINAL SETTING.

NOTE: When VGA or Y/Pb/Pr is selected as the main picture, nothing will be output from DPORT.

When this function is ON, DPORT cannot be selected as the sub picture. When this function is

ON, INPUT CHANGE is limited to be NORMAL or QUICK. When this function is ON and DPORT

is selected as the main picture, PIP CHANGE button of remote control (see page 11) is disabled.

POWER INDICATOR

SETTING COPY

Turns ON or OFF the LED located at the back of the monitor.

If “OFF” is selected, LED will not light when the LCD monitor is in active mode.

In a daisy chain scenario, select the OSD menu categories that you want to copy over to the

other monitor.

NOTE: When you use this function, monitors should be daisy chained by LAN. This function

resets to default when power is off. This function has a limit depending on the cable you use.

COPY START

ALL INPUT

RESET

Select “YES” and press the SET button to start copying.

All input terminals settings are copied when you select this item. Default is off.

Resets “MULTI DISPLAY” options back to factory settings except for POWER ON DELAY and

VIDEO OUT SETTING.

DISPLAY PROTECTION

POWER SAVE

Sets how long the monitor waits to go into power save mode after the signal is lost.

AUTO

NOTE: When connecting DVI, the video card might not stop sending the digital data even

though the image might have disappeared. If this occurs the monitor will not switch into power

management mode. POWER SAVE is disabled when AUTO OFF or CUSTOM is selected in

HUMAN SENSING.

STANDBY

AUTO POWER SAVE

AUTO STANDBY

The monitor automatically goes into OFF at the preset time period after signal is lost.

The monitor will return to normal mode when signal is restarted.

The monitor automatically goes into OFF at the preset time period after signal is lost.

Press the power button to return to normal mode.

DISABLE

The monitor will not goes into OFF after signal is lost.

HEAT STATUS

FAN CONTROL

Displays status of the FAN, BACKLIGHT and TEMPERATURE.

Cooling fan reduces the temperature of the display to protect from overheating.

AUTO, HIGH

If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.

SCREEN SAVER

GAMMA

Use the SCREEN SAVER function to reduce the risk of Image Persistence.

The display gamma is changed and ﬁxed when “ON” is selected.

OFF

BACKLIGHT

The brightness of backlight is decreased when “ON” is selected.

NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.

MOTION

The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at

user determined intervals. You can set interval time and zooming ratio.

This function is disabled when PIP, STILL, TEXT TICKER or TILE MATRIX are enabled.

OFF

SIDE BORDER COLOR

CHANGE PASSWORD

Adjusts the color of the side borders when a 4:3 image is displayed.

Press + button, the bar will become lighter.

Press - button, the bar will become darker.

Allows the security password to be changed.

The factory preset password is 0000.

SECURITY

RESET

Locks the security password.

OFF

Resets the following settings within the DISPLAY PROTECTION menu back to factory setting:

POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR.

EXTERNAL CONTROL

IP ADDRESS SETTING

NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN

SETTING is applied.

IP SETTING

Enabling this option automatically assigns an IP address to the monitor from your DHCP server.

Disabling this option allows you to register the IP address or subnet mask number obtained from

your network administrator.

AUTO

NOTE: Consult your network administrator for the IP address when “AUTO” is selected for

[IP SETTING].

IP ADDRESS:

Set your IP address of the network connected to the monitor when “MANUAL” is selected for

[IP SETTING].

192.168.0.10

English-25

SUBNET MASK:

Set your subnet mask number of the network connected to the monitor when “MANUAL” is

selected for [IP SETTING].

255.255.255.0

0.0.0.0

DEFAULT GATEWAY:

Set your default gateway of the network connected to the monitor when “MANUAL” is selected

for [IP SETTING].

NOTE: Set as [0.0.0.0] to delete the setting.

DNS

Set for IP ADDRESS setting of DNS server.

AUTO

AUTO: Automatically assign an IP address of DNS server connected to the monitor.

MANUAL: Set your IP address of DNS server connected to the monitor.

DNS PRIMARY:

Set your primary DNS settings of the network connected to the monitor.

NOTE: Set as [0.0.0.0] to delete the setting.

0.0.0.0

DNS SECONDARY:

Set your secondary DNS settings of the network connected to the monitor.

NOTE: Set as [0.0.0.0] to delete the setting.

MAC ADDRESS

LAN POWER

Displays the MAC ADDRESS.

Selects LAN operation mode. When “ON” selected, allows to supply power to LAN during power

save mode or standby mode.

OFF

NOTE: For enabling “AUTO ID” or “AUTO TILE MATRIX SETUP”, this function should be ON.

DDC/CI

PING

ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor.

Conﬁrm the response by communicating to the preset IP address.

ENABLE

192.168.0.10

IP ADDRESS RESET

RESET

Resets IP ADDRESS SETTING back to factory settings.

Resets the following setting within the EXTERNAL CONTROL menu back to factory settings:

DDC/CI.

ADVANCED OPTION1

INPUT DETECT

Selects the method of input detection the monitor uses when more than two input devices are

connected.

NONE

NOTE: When SUPER is selected in INPUT CHANGE, this function cannot be changed.

NONE

The Monitor will not search the other video input ports.

FIRST DETECT*²

When the current video input signal is not present, then the monitor searches for a video signal

from the other video input port. If the video signal is present in the other port, then the monitor

switches the video source input port to the new found video source automatically.

The monitor will not look for other video signals while the current video source is present.

LAST DETECT*²

When the monitor is displaying a signal from the current source and a new secondary source

is supplied to the monitor, the monitor will automatically switch to the new video source. When

current video input signal is not present, the monitor searches for a video signal from the other

video input port. If the video signal is present in the other port, then the monitor switches the

video source input port to the new found video source automatically.

VIDEO DETECT

Y/Pb/Pr, Y/Pb/Pr2*¹, SCART*¹, VIDEO*¹or S-VIDEO*¹inputs will have priority over DVI, VGA,

RGB/HV*¹. When Y/Pb/Pr, Y/Pb/Pr2*¹, SCART*¹, VIDEO*¹or S-VIDEO*¹input signal is present

the monitor will change and keep to the Y/Pb/Pr, Y/Pb/Pr2*¹, SCART*¹, VIDEO*¹or S-VIDEO*¹

input.

CUSTOM DETECT

Set the priority of input signals.

When CUSTOM DETECT is selected, monitor searches listed inputs only.

LONG CABLE COMP*¹

Manually compensates for image degradation caused from using a long cable.

(Analog input only)

ON/OFF

ON: Activates this function.

OFF: Deactivates this function.

OFF

SOG PEAK

Adjusts the sensitivity of the Sync On Green input signals. Adjusts the slice level when separating

synchronization from sync On Green signal input. Press “LEFT” or “RIGHT” to select.

GAIN

Adjusts gain value.

R-H.POSITION

G-H.POSITION

B-H.POSITION

Adjusts the position of the red component of the image.

Adjusts the position of the green component of the image.

Adjusts the position of the blue component of the image.

SYNC TERMINATION Selects the terminate resistance for matching the cable impedance.

HIGH

NORMAL

INPUT CHANGE Sets input change speed. When selected “SUPER”, allows to switch high-speed between set two

signals.

NOTE: When “QUICK” is selected, picture may be distorted when signal input is changed.

“SUPER” is released when selecting IMAGE FLIP except for NONE.

This function should be chosen after all adjustment options have been made for the input.

*1: This function depends on which option board you use.

*2: Only for DVI, DPORT, VGA, RGB/HV*¹, HDMI, HDMI2*¹, DPORT2*¹, DPORT3*¹input.

English-26

TERMINAL SETTING

DVI MODE

Selects the kind of DVI-D equipment which is connected to the DVI input. Select “DVI-PC” when

PC or other computer equipment is connected. Select “DVI-HD” when DVD player, which has

DVI-D output, is connected.

DVI-HD

RGB

D-SUB MODE

Selects the type of signal associated with the D-SUB input.

RGB: Analog input (R, G, B, H, V)

COMPONENT: Component (Y, Cb/Pb, Cr/Pr)

BNC MODE*¹

Selects the kind of equipment which is connected to the BNC input.

RGB: Analog input.

RGB

COMPONENT: Component.

SCART MODE*¹

Input mode for devices using SCART connectors.

OFF

1.1a

DisplayPort

Selects DisplayPort mode [1.1a] or [1.2].

[1.2] should be selected when using Multi-Stream Transport.*²

HDMI SIGNAL

DEINTERLACE

RAW: Disable the expanded feature.

EXPAND: Expand image contrast and increase detail in the dark and bright areas.

EXPAND

Selects the IP (Interlace to Progressive) conversion function.

NOTE: For DVI input “DVI-HD” needs to be enabled in the DVI mode menu. When INPUT2 of

SUPER is selected in INPUT CHANGE and displayed, this function cannot be changed.

Converts interlaced signals to progressive. This is the default setting.

OFF

Disables IP conversion. This setting is best suited for motion pictures, but increases the risk of

image retention.

COLOR SYSTEM*¹

The selected Color System depends on the video format of the input signal.

AUTO

VIDEO, S-VIDEO inputs only

AUTO

NTSC

Automatically chooses Color System setting based on input signal.

PAL

SECAM

4.43 NTSC

PAL-60

OVER SCAN

Some video formats may require different scanning modes in order to best display the image.

HDMI, Y/Pb/Pr, SCART*¹, VIDEO*¹, S-VIDEO*¹,

HDMI2*¹inputs only

Image size is larger than what can be displayed. The image edge will appear cropped.

Approximately 95% of the image will be shown on the screen.

OFF

Image size stays within the display area. The whole image is displayed on the screen.

NOTE: When you use a computer with HDMI out, please set “OFF”.

OPTION SETTING

OPTION POWER

You can set this setting when option board accessory is connected to the monitor.

Please contact your supplier for detailed information about Option board slot accessories.

Allow the monitor to supply power to Option board slot during power save mode or standby

OFF

mode.

NOTE: This function should be set to ON when using power save management by slot 2 type

option.

AUDIO

The function is available for slot 2 type option. Selects sound input signal according to slot2 type

option’s speciﬁcations. To activate DIGITAL, select OPTION for input signal and OPTION for

AUDIO INPUT.

ANALOG

NOTE: DIGITAL is activated only when OPTION is selected for input signal and OPTION for

AUDIO INPUT.

INTERNAL PC

OFF WARNING

The function is available for slot 2 type PC.

If OPTION POWER is OFF, a warning message appears when monitor power is turned off.

NOTE: Warning message does not appear when monitor power is turned off by OFF TIMER

setting or SCHEDULE setting.

OFF

AUTO OFF

Monitor power is automatically “OFF” when connected PC is OFF or the monitor is in power save

mode.

NOTE: Monitor power is not automatically “ON” when connected PC is ON.

START UP PC

FORCE QUIT

When ON is selected, connected PC start-up.

When ON is selected, it performs force-quit PC.

Please use this function only when the operating system cannot be shut down manually.

*1: This function depends on which option board you use.

*2: Multi-Stream Transport requires the corresponding video card. Contact your dealer for limitations of this function.

English-27

120Hz

(not adjustable)

TOUCH PANEL

RESET

(not adjustable)

Resets the following settings within the ADVANCED OPTION menu back to factory setting:

INPUT DETECT (except the priority of input signals), INPUT CHANGE (except for INPUT1 and

INPUT2), TERMINAL SETTING, DEINTERLACE, COLOR SYSTEM, OVER SCAN, AUDIO in

OPTION SETTING.

ADVANCED OPTION2

AUTO DIMMING

Adjusts the backlight of the LCD automatically depending on the amount of ambient light.

AUTO BRIGHTNESS

DPORT, DVI, VGA, RGB/HV*¹, DPORT2*¹,

DPORT3*¹inputs only

Adjusts the brightness level according to the input signal.

NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.

OFF

ROOM LIGHT

SENSING*²

The backlight of the LCD screen can be set to increase or decrease depending on the amount of

ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If

the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the

viewing experience more comfortable to the eye in a variety of lighting conditions.

NOTE: When ROOM LIGHT SENSING is set to MODE1 or MODE2, BACKLIGHT, AUTO

BRIGHTNESS and BACKLIGHT in SCREEN SAVER function are disabled.

OFF

Do not cover the room light sensing sensor when you use MODE1 or MODE2.

AMBIENT parameter setting

ROOM LIGHT SENSING in OSD, select MODE1 or MODE2 and set MAX LIMIT, IN BRIGHT and

IN DARK in each mode.

MAX LIMIT: This is the max level of backlight which you set.

IN BRIGHT: This is the backlight level that the monitor will go up to when the ambient light level is

highest.

IN DARK: This is the level of backlight that the monitor will go down to when the ambient light

level is low.

When the ROOM LIGHT SENSING is enabled the Backlight level of the screen changes

automatically according to the lighting conditions of the room (see ﬁgure below).

Factory Setting

BACKLIGHT range

BACKLIGHT range when

set to MAX LIMIT.

BACKLIGHT level set for

the monitor to use when

ambient lighting level is

low.

BACKLIGHT level set

for the monitor to use

when ambient lighting

level is high.

IN DARK

dark

IN BRIGHT

room bright condition

bright

Screen Backlight value by MODE1

Screen Backlight value by MODE2

MAX LIMIT: BACKLIGHT level is limited to your set level.

IN DARK: BACKLIGHT level set for the monitor to use when ambient lighting level is low.

IN BRIGHT: BACKLIGHT level set for the monitor to use when ambient lighting level is high.

HUMAN SENSING*²

HUMAN SENSING has three settings.

DISABLE

NOTE: POWER SAVE is disabled when AUTO OFF or CUSTOM is selected in HUMAN

SENSING.

DISABLE

No human sensing.

AUTO OFF

At the preset time, when no person is detected, BACKLIGHT and VOLUME automatically go

into OFF. When a person comes near the monitor again, the monitor will automatically return to

normal mode.

CUSTOM

BACKLIGHT and VOLUME automatically shift to the set value when detecting no person. When

a person comes near the monitor again, the monitor automatically return to normal mode and

display the input signal selected in INPUT SELECT.

INTELLI. WIRELESS DATA Select “ON” to activate INTELLIGENT WIRELESS DATA function (see page 44). A password is

required when using the function.

RESET

Resets “ADVANCED OPTION 2” settings back to factory setting, except for INTELLI. WIRELESS

DATA.

FACTORY RESET

Resets OSD options back to factory settings EXCEPT FOR: PICTURE MODE, VOLUME,

SCHEDULE SETTINGS, DATE & TIME, DAYLIGHT SAVINGS, SUB INPUT in PIP, ASPECT

in PIP, LANGUAGE, OSD ROTATION, MEMO, POWER ON DELAY, CHANGE PASSWORD,

SECURITY, IP ADDRESS SETTING, LAN POWER, PING and LONG CABLE COMP.

*1: This function depends on which option board you use.

*2: The function is available only when connecting the optional control unit.

English-28

NOTE 1: CREATING A SCHEDULE

The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be programmed.

To program the schedule:

1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET/POINT ZOOM or the + button

to enter the Settings menu. Highlight the desired schedule number and press SET/POINT ZOOM. The box next to the number will turn yellow.

The schedule can now be programmed.

2. Use the down button to highlight the hours setting in the ON time slot. Use the + and - buttons to set the hour. Use the up and down buttons to

highlight the minutes setting. Use the + and - buttons to set the minutes. Set the OFF time in the same manner.

3. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to highlight

PIC. MODE. Use the + and - buttons to choose the picture mode.

4. Use the down button to select a day on which the schedule will be enabled. Push the

SET/POINT ZOOM button to enable. If the schedule is to be ran every day, choose

EVERY DAY and press the SET/POINT ZOOM button. The circle next to EVERY DAY

will turn yellow. If a weekly schedule is desired, choose the days of the week using the up OFF TIMER

and down buttons and pressing SET/POINT ZOOM to select. Then highlight the EVERY

WEEK option and press SET/POINT ZOOM.

DVI

SCHEDULE:

(THU) JUN.18.2009 15:38

SETTINGS:

SCHEDULE SETTINGS

SCHEDULE LIST

DATE & TIME

RESET

ON:

– – : – –

– – – –

OFF:

INPUT:

PIC. MODE:

5. After a schedule is programmed the remaining schedules can then be set. Press MENU

to leave the OSD or press EXIT to go back to the previous menu.

EVERY DAY

EVERY WEEK

MON

TUE

FRI

WED

SAT

THU

SUN

NOTE: If schedules are overlapping then the schedule with the highest number will have

priority over the schedule with the lowest number. For example schedule #7 will have

priority over schedule #1.

Return

Choose

Mark

If selected input or picture mode is not available now, disable input or picture mode

is shown in red.

NOTE 2: IMAGE PERSISTENCE

Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a

residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not

permanent, but constant images being displayed for a long period of time should be avoided.

To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the

monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at

regular intervals whenever the screen is idle or turning off the monitor when not in use.

Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.

For long life use as Public Display

Image Sticking of LCD Panel

When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or

“ghost” image of previous image may be observed. (Image Persistence)

Image Persistence is not permanent, but when ﬁxed image is displayed for long period, ionic impurities inside LCD are accumulated along the

displayed image, and may be permanent. (Image Sticking)

Recommendations

To prevent Image Sticking, and for longer life usage of LCD, the following are recommended.

1. Fixed image should not be displayed for long period. Change ﬁxed images after short intervals.

2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule Functions.

3. Lower environmental temperatures prolong the lifespan of the monitor.

When Protective surface (glass, acrylic) is installed over the LCD surface, the LCD surface is located in an enclosed space, the monitor are

stacked, utilize the temperature sensors inside monitor.

To reduce the environmental temperature, use the Cooling Fan, Screen Saver and Low Brightness.

4. Please use “Screen Saver Mode” of monitor.

English-29

Remote Control Function

REMOTE CONTROL ID FUNCTION

Monitor ID:1

Monitor ID:2

Monitor ID:3

REMOTE CONTROL ID

The optional remote control can be used to control up to 100 individual MultiSync monitors

using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID

mode works in conjunction with the Monitor ID, allowing control of up to 100 individual

MultiSync monitors. For example: if there are many monitors being used in the same area,

a remote control in normal mode would send signals to every monitor at the same time (see

Figure 1). Using the remote in REMOTE CONTROL ID mode will only operate one speciﬁc

monitor within the group (see Figure 2).

Remote works

Figure 1

Remote in

Normal mode or

the REMOTE ID

is set to 0

TO SET REMOTE CONTROL ID

While holding down the REMOTE ID SET button on the remote control, use the KEYPAD to

input the Monitor ID (1-100) of the display to be controlled via remote. The remote can then

be used to operate the monitor having that speciﬁc Monitor ID number.

When 0 is selected or when the remote control is in normal mode, all monitors will be

operated.

Monitor ID:1

Monitor ID:2

Monitor ID:3

TO SET/RESET REMOTE CONTROL MODE

ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for

2 seconds.

Remote does

not work

Remote does

not work

Remote works

Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold

down for 2 seconds.

In order for this feature to work properly, the display must be assigned a Monitor ID number.

The Monitor ID number can be assigned under the MULTI DISPLAY menu in the OSD

(See page 23).

Figure 2

Remote set up

to use REMOTE

ID:3

Point the remote control towards the remote sensor of the desired monitor and press the

REMOTE ID SET button. The MONITOR ID number is shown on the display when your

remote control is in ID mode.

You need an optional remote control for this function.

Use the remote control to operate a monitor that has a speciﬁc MONITOR ID number assigned to it.

1. Set the MONITOR ID number for the display (See page 23). The MONITOR ID number can range from 1-100.

This MONITOR ID number allows the remote control to operate this speciﬁc monitor without affecting other monitors.

2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number

(1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose “0” to simultaneously

control all displays in range.

3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button.

The MONITOR ID number is shown in red on the display.

If the REMOTE CONTROLID is “0”, then all displays in range will show their respective MONITOR ID number in red.

If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same.

NOTE: GROUP ID cannot be speciﬁed via the remote control.

English-30

Multiple Monitors Connection

You can control mutliple monitors by using RS-232C, REMOTE IN or LAN daisy-chain connection.

NOTE:

Multiple monitors that are daisy-chained have a limit to the connectable monitors.

When manually specify the ID number or control by the speciﬁed ID number, please execute AUTO ID (see page 23)

previously.

Main Monitor

Connector

Sub Monitors

Connector

OUT

RS-232C

REMOTE IN

LAN1

LAN2

LAN1

LAN2

Connection

MultiSync

LAN1 LAN2

LAN Cable

MultiSync

English-31

Controlling the LCD monitor via RS-232C Remote Control

This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal.

Functions that can be controlled by a personal computer are:

•

Power ON or OFF.

Switching between input signals.

Sound Mute ON or OFF.

Connection

LCD Monitor + PC

MultiSync

RS-232C

RS-232C Cable

NOTE:

If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your

dealer for details.

For the pin assignment, please see page 49 “2) RS-232C input/output”.

To control a monitor, please use the control command. Instructions for the control command can be found on the CD included

with the display. The ﬁle is called “External_control.pdf”.

1) Interface

PROTOCOL

BAUD RATE

DATA LENGTH

PARITY BIT

STOP BIT

RS-232C

9600 [bps]

8 [bits]

NONE

1 [bit]

FLOW CONTROL NONE

This LCD monitor uses RXD, TXD and GND lines for RS-232C control.

The reverse type cable (null modem cable) (not include) should be used for RS-232C control.

English-32

2) Control command diagram

For other commands, please see “External_Control.pdf” ﬁle on the CD-ROM.

Function (Monitor ID = 1)

Code Data

Power ON

01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 31 03 73 0d

01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 34 03 76 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 46 03 04 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 33 03 71 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 31 03 73 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 31 03 72 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 43 03 01 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 35 03 77 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 37 03 75 0d

01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 44 03 06 0d

01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 31 03 09 0d

01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 32 03 0a 0d

Power OFF

Input Source Select DisplayPort

Input Source Select DVI

Input Source Select VGA

Input Source Select HDMI

Input Source Select Y/Pb/Pr

Input Source Select VIDEO

Input Source Select S-VIDEO

Input Source Select OPTION

Sound Mute ON

Sound Mute OFF

English-33

Controlling the LCD monitor via LAN Control

Connecting to a Network

Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function.

To use a LAN connection, you are required to assign an IP address.

Example of LAN connection:

Server

NOTE: Use a category 5 or higher LAN cable.

Hub

LAN cable

Network Setting by Using an HTTP Browser

Overview

Connecting the monitor to a network allows for monitor control from a computer via the network.

To perform the monitor control from a web browser, you must have an exclusive application installed on your computer.

The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP

server function. Please be sure to use “Microsoft Internet Explorer 7.0” or a higher version for the web browser.

(This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will

vary depending on the version of browser. Please refer to the help ﬁles and the other information provided in your software.)

Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the

monitor and entering the following URL.

Network Setting

http://<the Monitor’s IP address>/index.html

TIP:

The default IP address is assigned automatically to the monitor.

The exclusive application can be downloaded from our website.

NOTE:

If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to

refresh your web browser (or clear the cache).

The display or button’s response can be slowed down or operation may not be accepted depending the settings of

your network. Should this happen, consult your network administrator.

The LCD monitor may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a

moment and repeat. If you still can’t get a response, turn the monitor off and then back on.

To control a monitor please use the control command. See “Control command diagram” (page 33).

English-34

Preparation Before Use

Connect the monitor to a commercially available LAN cable before engaging in browser operations.

Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting

method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be

displayed depending on the effectiveness of the cache, and the contents set from the browser may not be reﬂected in operation.

It is recommended that a proxy server not be used unless it is unavailable.

Handling of the Address for Operation via a Browser

The host name can be used under the following cases:

If the host name corresponding to the IP address of the monitor has been registered to the domain name server (DNS) by the

network administrator, you can then access the network settings of the display via that registered host name using a compatible

browser.

If the host name corresponding to the IP address of the monitor has been conﬁgured in the “HOSTS” ﬁle of the computer being

used, you can then access the network settings of the display via that host name using a compatible browser.

Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by

specifying http://pd.nec.co.jp/index.html for the address or the entry column of the URL.

Example 2: When the IP address of the monitor is “192.168.73.1”, access is gained to the mail alert settings by specifying

http://192.168.73.1/index.html for the address or the entry column of the URL.

Operation

Access the following address to show HOME. Click each link on the left side of HOME.

http://<the Monitor’s IP address>/index.html

REMOTE CONTROL

Enable to control equivalent as the remote control key.

OSD menu

Enable to set the following OSD menu.

PICTURE, ADJUST, AUDIO, SCHEDULE, PIP, OSD, MULTI DISPLAY, DISPLAY PROTECTION, EXTERNAL CONTROL,

ADVANCED OPTION1, ADVANCED OPTION2.

NOTE:

Function of buttons which are shown on setting pages.

[APPLY]: Reﬂect your settings.

[CANCEL]: Return to the previous settings. NOTE: CANCEL is disabled after clicking APPLY.

[RELOAD]: Reload the settings.

[RESET]: Resets to the initial setting.

English-35

Network Setting

Click “NETWORK” on the left side of HOME.

IP SETTING

Set for IP ADDRESS setting.

AUTO: Automatically assign an IP address.

MANUAL: Set your IP address of the network connected to the monitor.

NOTE: Consult your network administrator for the IP address when [AUTO] is selected for

[IP SETTING].

IP ADDRESS

Set your IP address of the network connected to the monitor when [MANUAL] is selected for

[IP SETTING].

SUBNET MASK

Set your subnet mask number of the network connected to the monitor when [MANUAL] is selected

for [IP SETTING].

DEFAULT GATEWAY Set your default gateway of the network connected to the monitor when [MANUAL] is selected for

[IP SETTING].

NOTE: Set as [0.0.0.0] to delete the setting.

DNS

Set for IP ADDRESS setting of DNS server.

AUTO: Automatically assign an IP address of DNS server connected to the monitor.

MANUAL: Set your IP address of DNS server connected to the monitor.

PRIMARY DNS

Set your primary DNS settings of the network connected to the monitor.

NOTE: Set as [0.0.0.0] to delete the setting.

SECONDARY DNS

Set your secondary DNS settings of the network connected to the monitor.

NOTE: Set as [0.0.0.0] to delete the setting.

NOTE:

The following settings will reset back to the factory setting when “IP ADDRESS RESET” is selected by an EXTERNAL

CONTROL of OSD:

[IP SETTING]: AUTO, [IP ADDRESS]: 192.168.0.10, [SUBNET MASK]: 255.255.255.0, [DNS]: AUTO [DEFAULT

GATEWAY], [PRIMARY DNS] and [SECONDARY DNS] are blank.

English-36

Mail Setting

Click “MAIL” on the left side of HOME.

This option notiﬁes your computer of an error message via e-mail when using wired LAN. An error message notiﬁcation will be

sent when an error occurs in the monitor.

ALERT MAIL

Checking [ENABLE] will turn on the Alert Mail feature.

Checking [DISABLE] will turn off the Alert Mail feature.

STATUS MESSAGE

HOST NAME

Checking [ENABLE] will turn on the STATUS MESSAGE feature.

Checking [DISABLE] will turn off the STATUS MESSAGE feature.

Type in the hostname of the network connected to the monitor.

Up to 15 alphanumeric characters can be used.

DOMAIN NAME

Type in the domain name of the network connected to the monitor.

Up to 60 alphanumeric characters can be used.

SENDER’S ADDRESS

SMTP SERVER

Type in the senders address. Up to 60 alphanumeric and symbols characters can be used.

Type in the SMTP server name to be connected to the monitor.

Up to 60 alphanumeric characters can be used.

RECIPIENT’S

Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.

ADDRESS 1 TO 3

AUTHENTICATION

METHOD

This selects the authentication method of the e-mail transmission.

POP3 SERVER

USER NAME

This speciﬁes the address of the POP3 server that is used in the authentication of the e-mail.

This sets the user name for logging into the authentication server when authentication is required

for the e-mail transmission. Up to 60 alphanumeric characters can be used.

TEST MAIL

Click this button to send a test mail to check if your settings are correct.

NOTE:

TIP:

• If you execute a test, you may not receive an Alert mail.

Should this happen, check if the network settings are correct.

• If you entered an incorrect address in a test, you may not receive an Alert mail.

Should this happen, check if the Recipient’s Address is correct.

The Alert Mail settings will not be affected even when [RESET] is done from the menu.

For Control command diagram, please see ﬁle “External_Control.pdf” on the CD-ROM.

English-37

Alert error message list

Error number

* ErrorCode

Alert mail Message

Explanation

Measure

The monitor’s power supply is not

functioning normally.

Standby power Abnormal

Please contact your supplier.

70h ~ 7Fh

80h ~ Fh

The cooling fan has stopped.

Cooling fan Abnormal

Backlight abnormal

Please contact your supplier.

The monitor’s back light unit is not

functioning normally.

90h ~ 9Fh

A0h ~ AFh

The monitor is overheated.

Temperature Abnormal

Please contact your supplier.

SENSOR reached at the temperature

that the user had speciﬁed.

Reconﬁrm the setting condition from

OSD (DISPLAY PROTECTION-FAN

CONTROL) or please contact your

supplier.

A2h

*condition: DISPLAY PROTECTION-FAN

CONTROL-COOLING FAN = AUTO

The monitor doesn’t have the input

signal.

No signal

Please check “No picture” in

“Troubleshooting”.

B0h ~ BFh

D0h

The remaining capacity of the error log Proof of Play log memory size is 1 more

decreased.

Please get a log by using PD external

command. See page 43.

hour.

The system error occurred in the

monitor.

System error.

Please contact your supplier.

E0h ~ EFh

Sample: The following examples are content of Alert Mail that informs the temperature anomaly of monitor.

Sample: The following examples are content of test mail by browser.

English-38

SNMP Setting

Click “SNMP” on the left side of HOME.

This function allows for getting status and controlling of a monitor via the network.

Version:

SNMP v1 Authenticated plaintext by community name, not return a conﬁrmation message of Trap.

SNMP v2c Authenticated plaintext by community name, return a conﬁrmation message of Trap.

Community name:

The default setting of community name is “public”. It is read only. You can set community names for up to 3 settings.

Trap:

Sending error message to speciﬁed address when an error occurs in the monitor.

Check Box

Temperature

Explanation

Temperature abnormal

Cooling fan abnormal

Power abnormal

Error code

0xA0, 0xA1, 0xA2

Fan

0x80, 0x81

Power

0x70, 0x71, 0x72, 0x78

Inverter/Backlight

No Signal

Inverter or backlight abnormal 0x90, 0x91

No signal

0xB0

0xD0

0xE0

PROOF OF PLAY

System Error

Lower the log storage

System error

English-39

AMX Setting

Click “AMX” on the left side of HOME.

AMX BEACON

Turn on or off for detection from AMX Device Discovery when connecting to the network supported by

AMX’s NetLinx control system.

TIP:

When using a device that supports AMX Device Discovery, all AMX NetLinx control system will

recognize the device and download the appropriate Device Discovery Module from an AMX server.

Checking [ENABLE] will detect the device from AMX Device Discovery.

Checking [DISABLE] will not detect the device from AMX Device Discovery.

CRESTRON Setting

Click “CRESTRON” on the left side of HOME.

CRESTRON ROOMVIEW compatibility

The monitor supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and

controlled from a computer or a controller.

For more information, visit http://www.crestron.com

ROOMVIEW

ROOMVIEW for managing from the computer.

ON: Enables ROOMVIEW.

OFF: Disables ROOMVIEW.

CRESTRON

CONTROL

CRESTRON CONTROL for managing from the controller.

ON: Enables CRESTRON CONTROL.

OFF: Disables CRESTRON CONTROL.

CONTROLLER IP

ADDRESS

Set your IP address of CRESTRON SERVER.

IP ID

Set your IP ID of CRESTRON SERVER.

TIP: The CRESTRON settings are required only for use with CRESTRON ROOMVIEW.

For more information, visit http://www.crestron.com

English-40

Name Setting

Click “NAME” on the left side of HOME.

Set a monitor name. The name must be 16 characters or less. The default is model name.

Network Password Setting

Click “NETWORK PASSWORD” on the left side of HOME.

PJLink PASSWORD Set a password for PJLink*. A password must be 32 characters or less. Do not forget your password.

However, if you forget your password, consult with your dealer.

HTTP PASSWORD

Set a password for HTTP server. A password must be 10 characters or less.

HTTP PASSWORD

ENABLE

HTTP PASSWORD is required when logging in HTTP server.

Set a monitor name as USER NAME when inputting the password.

*What is PJLink?

PJLink is a standardization of protocol used for controlling devices of different manufacturers. This standard protocol is

established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005.

The device supports all the commands of PJLink Class 1.

Setting of PJLink will not be affected even when [RESET] is done from the menu.

English-41

PD List Information

Click “PD LIST” on the left side of HOME.

Show the list of ID and IP address of multiple monitors that are daisy-chained.

Only the master monitor can show the list.

Memo Setting

Click “MEMO” on the left side of HOME.

Set a title and meesage.

TITLE

A title must be 24 characters or less.

MESSAGE

A message must be 240 characters or less.

MEMO PASSWORD The default is “0000”.

MEMO PASSWORD MEMO PASSWORD is required when setting MEMO.

ENABLE

English-42

POINT ZOOM

Using “SET/POINT ZOOM” button on a remote control allows to enlarge a partial of image.

Press CH+/- button to zoom up or down. The image can be expanded from 1 to 10 times.

Press [SET/POINT ZOOM] button on a remote control. An icon will be a magniﬁer.

Move magniﬁer icon by [ ] [ ] [+] [-] button.

Press [CH+] to zoom up. Press [CH-] to zoom down.

Press [SET/POINT ZOOM] to disappear the icon.

Press [EXIT] to return to a normal size.

Press [MENU] to display OSD menu.<Setting Procedure>

NOTE:

• The image may be distorted during this function.

• This function does not work when set to PIP, POP, PBP, TILE MATRIX, SCREEN SAVER, SUPER in INPUT

CHANGE, IMAGE FLIP.

• When selected DYNAMIC or ZOOM in ASPECT, the image will be changed FULL, then start to POINT ZOOM.

After POINT ZOOM, the ASPECT will be returned previous ASPECT settings. When the ASPECT is changed

during POINT ZOOM, DYNAMIC and ZOOM will be FULL image.

• The magniﬁer icon does not move to no image area.

• POINT ZOOM will be released after changing input signal or power off.

• POINT ZOOM will be released when setting IMAGE FLIP or changing ASPECT setting during POINT ZOOM.

PROOF OF PLAY

This function allows to send message for the current status of monitor by self checking.

Check item

INPUT

Message

DVI, VGA, Y/Pb/Pr, HDMI, DPORT, HDMI2*, DPORT2*, DPORT3*, RGB/HV*, Y/Pb/Pr2*, SCART*,

VIDEO*, S-VIDEO*, OPTION*

①

②

③

Resolution

ex. (H)1920, (V)1080 , (H)1360, (V)768 or No signal or Invalid signal

IN1, IN2, IN3*, HDMI, DPORT, HDMI2*, DPORT2*, DPORT3*, OPTION (analog)*,

OPTION (digital)*

Audio INPUT

Audio signal

Picture Image

Audio out

Audio in or No Audio in or N/A (IN1, IN2, IN3*, OPTION (analog)*)

Normal Picture or No Picture

④

⑤

⑥

⑦

Normal Audio or No Audio

Cumulative time

(hour)/(minutes)/(second)

*: This function depends on which option board you use.

Sample:

HDMI

①

②

③

④

⑤

⑥

⑦

1920 x 1080

HDMI

Audio in

Normal Picture

Normal Audio

0h/0m/0s

NOTE:

For Proof of Play function, please see “External_Control.pdf” on the CD-ROM.

English-43

INTELLIGENT WIRELESS DATA

This function allows to get the data of monitor’s status by wireless communication even while the monitor is off.

Some menu of OSD, you can set by this function.

NOTE:

Sensor position: see page 9.

Please contact your supplier for detailed information.

Function name

Item Name

Read/Write

R/W

INPUT TYPE

PICTURE

ADJUST

AUDIO

R/W

SCHEDULE

PIP

R/W

Setting read and write

function

OSD

R/W

MULTI DISPLAY

R/W

DISPLAY PROTECTION

EXTERNAL CONTROL

ADVANCED OPTION1

ADVANCED OPTION2

FACTORY RESET

MODEL NAME

R/W

Read only

SERIAL NUMBER

MANUFACTURED DATE

FIRMWARE1

Display information

All data for service

FIRMWARE2

MAC ADDRESS

English-44

Features

Ultra Narrow Bezel: Provides the optimum solution in a tiling environment.

Reduced Footprint: Provides the ideal solution for environments with superior image quality.

Color Control Systems: Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a

variety of standards.

OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six

axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard provides

the monitor with a uniform color proﬁle. This assures that the colors displayed on the monitor are exactly the same as on the

color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your screen

and customise the color accuracy of your monitor to a variety of standards.

sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays and

other peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation and

backward compatibility with other common color standards.

OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use

on-screen menus.

Plug and Play: The Microsoft^®solution with the Windows^®operating system facilitates setup and installation by allowing

the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically

optimizing display performance.

IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a

lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and

lowering the air conditioning costs of the workplace.

FullScan Capability: Allows you to use the entire screen area in most resolutions, signiﬁcantly expanding image size.

VESA Standard (FDMIv1) Mounting Interface: Allows you to connect your LCD monitor to any VESA standard (FDMIv1) third

party mounting arm or bracket. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard

in North America.

DVI-D: The digital-only subset of DVI ratiﬁed by the Digital Display Working Group (DDWG) for digital connections between

computers and displays. As a digital-only connector, analog support is not provided for a DVI-D connector. As a DVI-based

digital only connection, only a simple adapter is necessary for compatibility between DVI-D and other DVI-based digital

connectors such as DFP and P&D. The DVI interface of this display supports HDCP.

TILE MATRIX,TILE COMP: Shows one image over multiple screens with accuracy while compensating for bezel width.

ZOOM: Expands/reduces image size for horizontal and vertical direction.

Self-diagnosis: If an internal error should occur, a failure state will be indicated.

HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent over

a Digital Visual Interface (DVI). If you are unable to view material via the DVI input, this does not necessarily mean the display is

not functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP

and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).

Option board slot: You can use an option board. Please contact your supplier for detailed information.

English-45

Troubleshooting

RED LED on monitor is blinking

No picture

•

A certain failure might have occurred, please contact your

nearest authorized NEC DISPLAY SOLUTIONS service

facility.

•

The signal cable should be completely connected to the

display card/computer.

•

The display card should be completely seated in its slot.

•

If the monitor is powered off by the inside temperature

being higher than the normal operating temperature, a RED

LED will blink six times. Power on the display again after

conﬁrming the inside temperature has been reduced to

normal operation temperature.

Check the main Power Switch, it should be in the ON

position.

•

Power Switch and computer power switch should be in the

ON position.

Check to make sure that a supported mode has been

selected on the display card or system being used. (Please

consult display card or system manual to change graphics

mode.)

Display image is not sized properly

•

Use the OSD Image Adjust controls to increase or decrease

the coarse adjustment.

•

Check to make sure that a supported mode has been

selected on the display card or system being used.

(Please consult display card or system manual to change

graphics mode.)

•

Check the monitor and your display card with respect to

compatibility and recommended settings.

•

Check the signal cable connector for bent or pushed-in pins.

The monitor automatically goes into OFF at the preset time

period after signal is lost. Press the power button.

Selected resolution is not displayed properly

•

Use OSD Display Mode to enter Information menu and

conﬁrm that the appropriate resolution has been selected. If

not, select corresponding option.

Power Button does not respond

•

Unplug the power cord of the monitor from the AC outlet to

turn off and reset the monitor.

No Sound

•

Check the main Power Switch on the back side of the monitor.

•

Check to see if audio cable is properly connected.

Image persistence

•

Check to see if mute is activated.

Please be aware that LCD Technology may experience

a phenomenon known as Image Persistence. Image

Persistence occurs when a residual or “ghost” image of a

previous image remains visible on the screen. Unlike CRT

monitors, LCD monitors’ image persistence is not permanent,

but constant images being displayed for a long period of time

should be avoided. To alleviate image persistence, turn off

the monitor for as long as the previous image was displayed.

For example, if an image was on the monitor for one hour

and a residual image remains, the monitor should be turned

off for one hour to erase the image.

Check to see if volume is set at minimum.

Check to see if computer supports an audio signal through

DisplayPort.

If unsure, contact the computer manufacturer.

•

Check to see if SURROUND is ON.

Remote Control is not available

•

Check the Remote Control’s batteries status.

Check if batteries are inserted correctly.

Check if the Remote Control is pointing at the monitor’s

remote sensor.

NOTE:

As with all personal display devices, NEC DISPLAY

SOLUTIONS recommends displaying moving images

and using a moving screen saver at regular intervals

whenever the screen is idle or turning off the monitor

when not in use.

•

Check the IR LOCK SETTING status.

The remote control system may not function when direct

sunlight or strong illumination strikes the remote control

sensor of the LCD monitor, or when there is an object in the

path.

Image is unstable, unfocused or swimming is apparent

•

“SCHEDULE”/“OFF TIMER” function is not working properly

Signal cable should be completely attached to the computer.

•

The “SCHEDULE” function will be disabled when the “OFF

TIMER” is set.

•

Use the OSD Image Adjust controls to focus and adjust

display by increasing or decreasing the ﬁne adjustment.

When the display mode is changed, the OSD Image Adjust

settings may need to be re-adjusted.

•

If the “OFF TIMER” function is enabled and the power to

the LCD monitor is turned off when the power supply is

interrupted unexpectedly, then the “OFF TIMER” will be reset.

•

Check the monitor and your display card with respect to

compatibility and recommended signal timings.

Snowy Picture, Poor Sound in TV

•

Check antenna/cable connection. Use new cable if

necessary.

If your text is garbled, change the video mode to non-

interlace and use 60Hz refresh rate.

The image may be distorted when turning the power on or

changing the settings.

Interference in TV

•

Check components for shielding, move away from monitor if

necessary.

Image of component signal is greenish

Check to see if the Y/Pb/Pr input connector is selected.

•

RS-232C or LAN control is not available

Check RS-232C or LAN cable connection.

•

LED on monitor is not lit (no green or red color can be seen)

•

Power Switch should be in the ON position and power cord

should be connected.

•

Check the main Power Switch, it should be in the ON position.

Make certain the computer is not in a power-saving mode

(touch the keyboard or mouse).

•

Check to see that the power indicator option in the OSD is

set to ON.

Either light vertical or horizontal stripes may appear, depending on the speciﬁc display pattern. This is no product fault or degradation.

English-46

Speciﬁcations - X464UN

Product Speciﬁcations

LCD Module

46”/1168 mm diagonal

Pixel Pitch: 0.530 mm

Resolution: 1920 x 1080

Color: Over 16 million colors (depending on video card used)

Brightness: 700 cd/m²(Max.), 500 cd/m²(Factory setting Typ.) @25°C

Contrast Ratio: 3500:1

Viewing Angle: 89° (typ) @ CR>10

Frequency

Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)

31.5 kHz - 91.1 kHz (Digital Input)

Vertical: 50.0 - 85.0 Hz

Pixel Clock

Viewable Size

Input Signal

DVI

25.2 MHz - 162.0 MHz

1018.1 x 572.7 mm

DVI-D 24pin

Digital RGB

DVI (HDCP)

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, 1920X1080 (60Hz), 1080p, 1080i

DisplayPort DisplayPort Connector Digital RGB

DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920x1080 (60 Hz),

1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*^1,*⁴

VGA*²

HDMI

15pin Mini D-sub

Analog RGB

Sync

0.7 Vp-p/75 ohm

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920X1080 (60Hz)

Separate: TTL level (Pos./Neg.)

Composite sync on Green Video: 0.3 Vp-p Neg.

HDMI Connector

15pin Mini D-sub

Digital YUV

Digital RGB

HDMI

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920x1080 (60 Hz),

1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,

3840x2160 (30Hz/24Hz/25Hz)*^1,*⁴, 4096x2160 (24Hz)*^1,*⁴

Y/Pb/Pr*²

Component

Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm

HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz

Output Signal

DisplayPort DisplayPort Connector Digital RGB

AUDIO

DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3

Stereo L/R 0.5 Vrms

STEREO Mini Jack

Analog Audio

Input

HDMI Connector

Digital Audio

PCM 32, 44.1, 48 KHz (16/20/24bit)

Stereo L/R 0.5 Vrms

DisplayPort Connector Digital Audio

STEREO Mini Jack Analog Audio

AUDIO

Output

Speaker Output

Control

External Speaker Jack 15 W + 15 W (8 ohm)

RS-232C In: 9 Pin D-sub

LAN: RJ-45 10/100 BASE-T

Remote IN: Stereo Mini jack 3.5

Service port

USB service port for maintenance

3.0 - 1.2 A @ 100-240V AC, 50/60Hz

Temperature*³: 0 - 40°C / 32 - 104°F

Power Supply

Operational Environment

Storage Environment

Humidity: 20 - 80% (without condensation)

Altitude: 0 - 3000 m (Brightness may decrease with altitude)

Temperature: -20 - 60°C / -4 - 140°F

Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C

Dimension

1024.0 (W) x 578.6 (H) x 99.7 (D) mm / 40.3 (W) x 22.8 (H) x 3.9 (D) inches

Weight

23.0 kg (50.7 lbs)

VESA compatible mounting interface

Power Management

Plug & Play

300 mm x 300 mm (M6, 4 Holes)

VESA DPM

VESA DDC2B, DDC/CI, DisplayPort

16V/3.6 A

Power supply for Slot 2 type OPTION

Accessories

Setup manual, Power Cord, Video Signal cable (DisplayPort to DisplayPort cable), LAN cable,

Clamp x 1, Screw x 1, CD-ROM

NOTE: Technical speciﬁcations are subject to change without notice.

*1: Compressed image.

*2: Common terminal.

*3: When you use option board accessories, please contact your supplier for detailed information.

*4: Displayed text may be blurred.

English-47

Speciﬁcations - X464UNV

Product Speciﬁcations

LCD Module

46”/1168 mm diagonal

Pixel Pitch: 0.530 mm

Resolution: 1920 x 1080

Color: Over 16 million colors (depending on video card used)

Brightness: 500 cd/m²(Max.), 350 cd/m²(Factory setting Typ.) @25°C

Contrast Ratio: 3500:1

Viewing Angle: 89° (typ) @ CR>10

Frequency

Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)

31.5 kHz - 91.1 kHz (Digital Input)

Vertical: 50.0 - 85.0 Hz

Pixel Clock

Viewable Size

Input Signal

DVI

25.2 MHz - 162.0 MHz

1018.1 x 572.7 mm

DVI-D 24pin

Digital RGB

DVI (HDCP)

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, 1920X1080 (60Hz), 1080p, 1080i

DisplayPort DisplayPort Connector Digital RGB

DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920x1080 (60 Hz),

1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*^1,*⁴

VGA*²

HDMI

15pin Mini D-sub

Analog RGB

Sync

0.7 Vp-p/75 ohm

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920X1080 (60Hz)

Separate: TTL level (Pos./Neg.)

Composite sync on Green Video: 0.3 Vp-p Neg.

HDMI Connector

15pin Mini D-sub

Digital YUV

Digital RGB

HDMI

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920x1080 (60 Hz),

1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,

3840x2160 (30Hz/24Hz/25Hz)*^1,*⁴, 4096x2160 (24Hz)*^1,*⁴

Y/Pb/Pr*²

Component

Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm

HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz

Output Signal

DisplayPort DisplayPort Connector Digital RGB

AUDIO

DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3

Stereo L/R 0.5 Vrms

STEREO Mini Jack

Analog Audio

Input

HDMI Connector

Digital Audio

PCM 32, 44.1, 48 KHz (16/20/24bit)

Stereo L/R 0.5 Vrms

DisplayPort Connector Digital Audio

STEREO Mini Jack Analog Audio

AUDIO

Output

Speaker Output

Control

External Speaker Jack 15 W + 15 W (8 ohm)

RS-232C In: 9 Pin D-sub

LAN: RJ-45 10/100 BASE-T

Remote IN: Stereo Mini jack 3.5

Service port

USB service port for maintenance

2.6 - 1.1 A @ 100-240V AC, 50/60Hz

Temperature*³: 0 - 40°C / 32 - 104°F

Power Supply

Operational Environment

Storage Environment

Humidity: 20 - 80% (without condensation)

Altitude: 0 - 3000 m (Brightness may decrease with altitude)

Temperature: -20 - 60°C / -4 - 140°F

Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C

Dimension

1024.0 (W) x 578.6 (H) x 117.3 (D) mm / 40.3 (W) x 22.8 (H) x 4.6 (D) inches

Weight

22.8 kg (50.3 lbs)

VESA compatible mounting interface

Power Management

Plug & Play

300 mm x 300 mm (M6, 4 Holes)

VESA DPM

VESA DDC2B, DDC/CI, DisplayPort

16V/3.6 A

Power supply for Slot 2 type OPTION

Accessories

Setup manual, Power Cord, Video Signal cable (DisplayPort to DisplayPort cable), LAN cable,

Clamp x 1, Screw x 1, CD-ROM

NOTE: Technical speciﬁcations are subject to change without notice.

*1: Compressed image.

*2: Common terminal.

*3: When you use option board accessories, please contact your supplier for detailed information.

*4: Displayed text may be blurred.

English-48

Speciﬁcations - X554UN

Product Speciﬁcations

LCD Module

55”/1388 mm diagonal

Pixel Pitch: 0.630 mm

Resolution: 1920 x 1080

Color: Over 16 million colors (depending on video card used)

Brightness: 700 cd/m²(Max.), 500 cd/m²(Factory setting Typ.) @25°C

Contrast Ratio: 3500:1

Viewing Angle: 89° (typ) @ CR>10

Frequency

Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)

31.5 kHz - 91.1 kHz (Digital Input)

Vertical: 50.0 - 85.0 Hz

Pixel Clock

Viewable Size

Input Signal

DVI

25.2 MHz - 162.0 MHz

1209.6 x 680.4 mm

DVI-D 24pin

Digital RGB

DVI (HDCP)

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, 1920X1080 (60Hz), 1080p, 1080i

DisplayPort DisplayPort Connector Digital RGB

DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920x1080 (60 Hz),

1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*^1,*⁴

VGA*²

HDMI

15pin Mini D-sub

Analog RGB

Sync

0.7 Vp-p/75 ohm

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920X1080 (60Hz)

Separate: TTL level (Pos./Neg.)

Composite sync on Green Video: 0.3 Vp-p Neg.

HDMI Connector

15pin Mini D-sub

Digital YUV

Digital RGB

HDMI

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920x1080 (60 Hz),

1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,

3840x2160 (30Hz/24Hz/25Hz)*^1,*⁴, 4096x2160 (24Hz)*^1,*⁴

Y/Pb/Pr*²

Component

Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm

HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz

Output Signal

DisplayPort DisplayPort Connector Digital RGB

AUDIO

DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3

Stereo L/R 0.5 Vrms

STEREO Mini Jack

Analog Audio

Input

HDMI Connector

Digital Audio

PCM 32, 44.1, 48 KHz (16/20/24bit)

Stereo L/R 0.5 Vrms

DisplayPort Connector Digital Audio

STEREO Mini Jack Analog Audio

AUDIO

Output

Speaker Output

Control

External Speaker Jack 15 W + 15 W (8 ohm)

RS-232C In: 9 Pin D-sub

LAN: RJ-45 10/100 BASE-T

Remote IN: Stereo Mini jack 3.5

Service port

USB service port for maintenance

3.8 - 1.6 A @ 100-240V AC, 50/60Hz

Temperature*³: 0 - 40°C / 32 - 104°F

Power Supply

Operational Environment

Storage Environment

Humidity: 20 - 80% (without condensation)

Altitude: 0 - 3000 m (Brightness may decrease with altitude)

Temperature: -20 - 60°C / -4 - 140°F

Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C

Dimension

1215.3 (W) x 686.1 (H) x 99.6 (D) mm / 47.8 (W) x 27.0 (H) x 3.9 (D) inches

Weight

29.2 kg (64.4 lbs)

VESA compatible mounting interface

Power Management

Plug & Play

400 mm x 400 mm (M6, 4 Holes)

VESA DPM

VESA DDC2B, DDC/CI, DisplayPort

16V/3.6 A

Power supply for Slot 2 type OPTION

Accessories

Setup manual, Power Cord, Video Signal cable (DisplayPort to DisplayPort cable), LAN cable,

Clamp x 3, Screw x 3, CD-ROM, Thumbscrew for optional stand x 2

NOTE: Technical speciﬁcations are subject to change without notice.

*1: Compressed image.

*2: Common terminal.

*3: When you use option board accessories, please contact your supplier for detailed information.

*4: Displayed text may be blurred.

English-49

Speciﬁcations - X554UNS

Product Speciﬁcations

LCD Module

55”/1388 mm diagonal

Pixel Pitch: 0.630 mm

Resolution: 1920 x 1080

Color: Over 16 million colors (depending on video card used)

Brightness: 700 cd/m²(Max.), 500 cd/m²(Factory setting Typ.) @25°C

Contrast Ratio: 3500:1

Viewing Angle: 89° (typ) @ CR>10

Frequency

Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)

31.5 kHz - 91.1 kHz (Digital Input)

Vertical: 50.0 - 85.0 Hz

Pixel Clock

Viewable Size

Input Signal

DVI

25.2 MHz - 162.0 MHz

1209.6 x 680.4 mm

DVI-D 24pin

Digital RGB

DVI (HDCP)

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, 1920X1080 (60Hz), 1080p, 1080i

DisplayPort DisplayPort Connector Digital RGB

DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920x1080 (60 Hz),

1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (30Hz/24Hz)*^1,*⁴

VGA*²

HDMI

15pin Mini D-sub

Analog RGB

Sync

0.7 Vp-p/75 ohm

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920X1080 (60Hz)

Separate: TTL level (Pos./Neg.)

Composite sync on Green Video: 0.3 Vp-p Neg.

HDMI Connector

15pin Mini D-sub

Digital YUV

Digital RGB

HDMI

VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*¹, WUXGA60*¹, 1920x1080 (60 Hz),

1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,

3840x2160 (30Hz/24Hz/25Hz)*^1,*⁴, 4096x2160 (24Hz)*^1,*⁴

Y/Pb/Pr*²

Component

Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm

HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz

Output Signal

DisplayPort DisplayPort Connector Digital RGB

AUDIO

DisplayPort Complies with Standard V1.2, applicable to HDCP V1.3

Stereo L/R 0.5 Vrms

STEREO Mini Jack

Analog Audio

Input

HDMI Connector

Digital Audio

PCM 32, 44.1, 48 KHz (16/20/24bit)

Stereo L/R 0.5 Vrms

DisplayPort Connector Digital Audio

STEREO Mini Jack Analog Audio

AUDIO

Output

Speaker Output

Control

External Speaker Jack 15 W + 15 W (8 ohm)

RS-232C In: 9 Pin D-sub

LAN: RJ-45 10/100 BASE-T

Remote IN: Stereo Mini jack 3.5

Service port

USB service port for maintenance

3.8 - 1.6 A @ 100-240V AC, 50/60Hz

Temperature*³: 0 - 40°C / 32 - 104°F

Power Supply

Operational Environment

Storage Environment

Humidity: 20 - 80% (without condensation)

Altitude: 0 - 3000 m (Brightness may decrease with altitude)

Temperature: -20 - 60°C / -4 - 140°F

Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C

Dimension

1213.5 (W) x 684.3 (H) x 100.4 (D) mm / 47.8 (W) x 26.9 (H) x 4.0 (D) inches

Weight

27.9 kg (61.5 lbs)

VESA compatible mounting interface

Power Management

Plug & Play

400 mm x 400 mm (M6, 4 Holes)

VESA DPM

VESA DDC2B, DDC/CI, DisplayPort

16V/3.6 A

Power supply for Slot 2 type OPTION

Accessories

Setup manual, Power Cord, Video Signal cable (DisplayPort to DisplayPort cable), LAN cable,

Clamp x 3, Screw x 3, CD-ROM, Thumbscrew for optional stand x 2

NOTE: Technical speciﬁcations are subject to change without notice.

*1: Compressed image.

*2: Common terminal.

*3: When you use option board accessories, please contact your supplier for detailed information.

*4: Displayed text may be blurred.

English-50

Pin Assignment

1) Analog multi input (MiniDsub15p): VGA, Y/Pb/Pr

Pin No Name

Red, Y/Pb/Pr_Pr

Green, Y/Pb/Pr_Y

Blue, Y/Pb/Pr_Pb

GND

Mini D-SUB 15P (Monitor side)

DDC-GND

Red-GND

Green-GND

Blue-GND

+5V (DDC)

GND

DDC-SDA

H-SYNC

V-SYNC

DDC-SCL

2) RS-232C input/output

Pin No Name

D-SUB 9P (Monitor side)

RXD

TXD

GND

This LCD monitor uses RXD, TXD and GND lines for RS-232C control.

3) REMOTE IN

English-51

Manufacturer’s Recycling and Energy Information

NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top

priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly

products, and always strive to help deﬁne and comply with the latest independent standards from agencies such as ISO

(International Organisation for Standardization) and TCO (Swedish Trades Union).

Disposing of your old NEC product

The aim of recycling is to gain an environmental beneﬁt by means of re-use, upgrading, reconditioning or reclamation of

material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely

disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures

and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.

All required information concerning the disposal of the product and country-speciﬁc information on recycling facilities can be

found on our following websites:

http://www.nec-display-solutions.com/greencompany/ (in Europe),

http://www.nec-display.com (in Japan) or

http://www.necdisplay.com (in USA).

Energy Saving

This monitor features an advanced energy saving capability. When a Display Power Management signal is sent to the monitor,

the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.

Mode

Power consumption

LED colour

Approx. 120 W (X464UN)

Approx. 90 W (X464UNV)

Approx. 150 W (X554UN)

Approx. 150 W (X554UNS)

Normal Operation*¹

Green

Energy Saving Mode*¹

Power Off

Less than 2.5 W

Less than 0.5 W

Amber

Red

*1: without any option, with factory settings.

WEEE Mark (European Directive 2012/19/EU)

Within the European Union

EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic

products carrying the mark (left) must be disposed of separately from normal household waste. This includes

monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your

NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased

the product, or if applicable, follow any agreements made between yourself and NEC.

The mark on electrical and electronic products only applies to the current European Union Member States.

Outside the European Union

If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority

so as to comply with the correct disposal method.

English-52

Uniden Ubw2101 User Manual
Samsung Svmi 16e User Manual
Samsung Mc18ac2 09 User Manual
Panasonic Kx Tg5664 User Manual
Panasonic Kx Fl611 User Manual
HP 9000 A 180 User Manual
D LINK AC1200 DWR 961 User Manual1
CRAFTSMAN 137.415030 User Manual
CANON POWERSHOT A420 User Manual
ASUS VP229Q User Manual