Master Plumber Mp35 User Manual

by  
Garbage Disposal  
Product Installation Manual  
WH007  
Before Installing:  
NOTE: The Cyclonehaus Garbage Disposal has been designed to  
operate on 110 volt, 50/60 Hz exclusively. Using any other voltage or Hz  
may affect the garbage disposal  
IMPORTANT: Read all instructions thoroughly. Keep this guide for future  
reference.  
CAUTION: Review safety instructions first to avoid risk of fire,  
electrical shock or injury before using disposal.  
Tools and Materials You May Need:  
• Phillips & Flat Screwdriver  
• Hacksaw  
• Pipe Wrench  
• Dowel or Steel Punch  
• Power Cord  
• Plumber’s Putty  
• Dishwasher Connector Kit  
• Hammer  
• Strain Relief  
1
2. EZ MOUNT SYSTEM  
7. From underneath the sink, slip fiber gasket (see 1)  
onto exposed sink flange. With arrows pointing up, screw  
support ring (see 2) onto the sink flange, hand tighten  
until the sink flange will not move (see photo H). At this  
point you may want to insert stopper in sink and fill with  
water to check sink flange seal and ensure there are no  
leaks.  
8. Place mount ring (see 3) over sink flange and hold in  
place while installing cushion mount (see 4) (large side  
down) so the groove on the inside of cushion mount fits  
over lip on sink flange, similar to putting the lid on a  
plastic container (see photo I, J and K).  
I
H
1
2
3
J
4
K
CUSHION MOUNT DETAIL  
IMPORTANT NOTICE: CUSHION MOUNT DETAIL  
When the cushion mount is installed correctly, the lip of the sink flange fits into the groove on  
the inside of the cushion mount and mount ring can be pulled downward over cushion mount  
and will be free to rotate. The bottom bead of the cushion mount acts as a gasket between the  
bottom of the sink flange and the top of the disposal. See photo D.  
3
3. GROUNDING INSTRUCTIONS  
FOR GARBAGE DISPOSALS EQUIPPED WITH A GROUNDED PLUG-IN CORD  
This appliance must be grounded. In the event of a malfunction or breakdown, grounding provides  
a path of least resistance for electric current to reduce the risk of electric shock. This appliance is  
equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug  
must be plugged into an appropriate outlet that is properly installed and grounded in accordance  
with all local codes and ordinances.  
4. ELECTRICAL CONNECTIONS  
IF YOU ARE NOT FAMILIAR WITH ELECTRICAL POWER AND PROCEDURES,  
CALL A QUALIFIED ELECTRICIAN.  
DANGER: IMPROPER CONNECTION OF THE EQUIPMENT-GROUNDING CONDUCTOR CAN  
RESULT IN A RISK OF ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN IF YOU  
ARE IN DOUBT AS TO WHETHER THE APPLIANCE IS PROPERLY GROUNDED. DO NOT  
MODIFY THE PLUG PROVIDED WITH THE APPLIANCE IF IT WILL NOT FIT THE OUTLET,  
HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.  
1. Connect garbage disposal to 110 volt, 50/60 Hx AC current only.  
2. If plug-in cord is used, use a three prong plug (see photo L). Ground wire should be attached to  
the ground screw in the bottom of the end bell (see photo M).  
3. Use a cable clamp strain relief connector were power cord enters the garbage disposal (see  
photo N).  
L
M
N
4
Wiring Disposal Directly to House Current  
This appliance must be connected to a grounded, metal permanent wiring system or an equip-  
ment-grounding conductor must be run with the circuit conductors and connected to the equip-  
ment-grounding terminator or lead on the appliance.  
1. If you use BX cable:  
a. Install cable connector in hole.  
b. Connect white wire to white lead of disposal.  
c. Connect black.  
d. Connect bare ground.  
IF BX cable it not used, provide a separate ground wire to nearest cold water metal pipe or other  
suitable ground, using the screw in the bottom of the end bell for the ground wire (see photo C).  
2. If your power supply does not include a ground wire, you must provide one unless metal cable  
is used. Attach a copper wire securely to disposal ground screw and attach other end of wire to a  
metal cold water pipe. Use only UL approved ground clamp. If plastic pipe is used in your home, a  
qualified electrician must install a proper ground.  
5. ATTACHING DISCHARGE ELBOW  
1. Connect waste elbow to the disposal (see photo J) proceed to step 6 then connect bottom of the  
elbow by tightening the slip nut (see photo K).  
2. If you are connecting to a dishwasher, return to proper section. If not, make sure all plumbing  
connections are tight and in accordance with all plumbing codes and ordinances. Run water and  
check for leaks.  
J
K
5
6. CONNECTING DISPOSAL TO EZ MOUNT  
1. Line up disposal under mounting assembly. Guide hopper projections into mount ring slots. Turn  
mount ring about 1/4” to right so that the disposal is temporarily supported (see photo O).  
2. Turn mount ring and disposal until disposal elbow lines up with trap (see photo P).  
3. Turn mount ring to the right (counter-clockwise) until it locks up tight. Insert shaft of screwdriver  
into slot on mount ring and tighten until the lock position is achieved. Hopper projections must be to  
extreme left of mounting slots (see photo Q).  
4. If mount ring is hard to turn, you may add a small amount of petroleum jelly or liquid soap to  
hopper projections. Run water and check for leaks.  
P
O
Q
8. AIR SWITCH INSTALLATION  
1. Drill a 1 1/4” hole in the countertop.  
2. Use the rubber gasket above the counter for the air switch on the outside and tighten with plastic  
nut from below your sink.  
3. Attach one end of the air tube to bottom of air switch button and the other end to the bottom  
center of the garbage disposal. Cut the tube to desired length.  
4. Your air switch is ready to be used. Press to deploy the garbage disposal and press once again  
to stop.  
6
7. DISHWASHER CONNECTION  
If you are utilizing a dishwasher, complete the following procedure.  
1. Using a blunt instrument like a steel punch or wooden dowel, knock out entire plug. Do not use a screwdriver  
or sharp instrument. When knockout plug falls into garbage disposal, remove it.  
2. Connect dishwasher hose using hose clamp. If hose size is different, you will need a Dishwasher Connector  
Kit. Make sure all plumbing connections are tight and in accordance with all plumbing codes and ordinates. Run  
water and check for leaks.  
* Airgap may not be required  
for all installations. Check  
local plumbing codes.  
7
9. OPERATING INSTRUCTIONS  
The Anti-Jam Swivel Impellers make a clicking sound as they swing into place.  
This indicates normal operation.  
1. Remove sink stopper. Turn on a medium flow of cold water.  
2. Turn switch to ON position; your motor is turning at full speed and ready to use.  
3. Scrape in food waste. Down the drain go table scraps, peels, rinds, seeds, etc. To speed up food  
waste disposal, cut or break up large rinds and cobs. Fibrous husks require considerable grinding  
time and are more easily thrown away with other trash. Do not be alarmed that the disposal slows  
down while grinding. The disposal is actually increasing torque (grinding power) and is operating  
under normal conditions.  
4. Before turning disposal off, let water and disposal run for approximately 15 seconds after  
shredding stops. This assures that all waste is thoroughly flushed through the trap and drain.  
5. It is not recommended to use hot water while running disposal. Cold water will keep waste and  
fats solid so the disposal can flush away particles.  
TIPS FOR SUCCESSFUL OPERATION  
1. Be sure disposal is empty before using your dishwasher so it may drain properly.  
2. You may want to leave the stopper in the drain when not in use to prevent utensils and foreign  
objects from falling in.  
3. Your disposal is ruggedly built to give you many years of trouble-free service. It will handle all  
normal food wastes but it will NOT grind or dispose of such items as plastic, tin cans, bottle caps,  
glass, china, leather, cloth, rubber, string, clam and oyster shells, aluminum foil, feathers, bones,  
coffee grounds, etc.  
10. CARE AND MAINTENANCE  
DO NOT ATTEMPT TO LUBRICATE YOUR DISPOSAL!  
The motor is permanently lubricated. The disposal is self-cleaning and scours its internal parts with  
each use. NEVER put lye or chemical drain cleaners into the disposal, as they cause serious  
corrosion of metal parts. If used, resulting damage can be easily detected and all warranties are  
void. Mineral deposits from your water can form on the stainless steel turntable, giving the appear-  
ance of rust. DO NOT BE ALARMED, the stainless steel turntables used will not corrode.  
To clean disposal, run multiple trays of ice through disposal during a grinding cycle.  
We reserve the right to change the features, packing and  
fittings of the WH007 without notice.  
8

Trion Air Boss Dc 112 User Manual
Toshiba Ras 18lah A User Manual
Snapper 10a900 User Manual
Scotsman Ice Air And Water Cooled C1848 User Manual
Samsung Sf 555p User Manual
Samsung Aw1809b User Manual
Samsung Aw109ab User Manual
Olympus Camedia B 20lpc User Manual
NEC NP04WK User Manual
GE 19 User Manual