MIELE DA 424 V EXT User Manual

Operating and installation instructions

Cooker hoods

DA 420 V, DA 420 V EXT

DA 424 V, DA 424 V EXT

en - GB, AU, NZ

To avoid the risk of accidents

or damage to the appliance

it is essential to read these

instructions before it is installed

and used for the first time.

M.-Nr. 07 261 480

Contents

Operation with DSM 400 control module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Connection to a window contact switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Potential free connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Connection to a light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Condensate trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Silencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Caring for the environment

Disposal of the packing

material

Disposal of your old appliance

Electrical and electronic appliances

often contain materials which, if

handled or disposed of incorrectly,

could be potentially hazardous to

human health and to the environment.

They are, however, essential for the

correct functioning of your appliance.

Please do not therefore dispose of it

with your household waste.

The transport and protective packing

has been selected from materials which

are environmentally friendly for

disposal, and can normally be

recycled.

Packaging e.g. cling film, polystyrene

and plastic wrappings must be kept out

of the reach of babies and young

children. Danger of suffocation!

Dispose of or recycle all packaging

materials safely as soon as possible.

Please dispose of it at your local

community waste collection / recycling

centre or contact your dealer for

advice. Ensure that it presents no

danger to children while being stored

for disposal.

It should be unplugged or disconnected

from the mains electricity supply by a

competent person.

Warning and Safety instructions

This appliance is not intended for

This appliance complies with all

relevant local and national safety

requirements. Inappropriate use

use by persons (including children)

with reduced physical, sensory or

mental capabilities, or lack of

can, however, lead to personal injury

and damage to property.

experience or knowledge, unless they

are supervised whilst using it or have

been shown how to use it correctly by a

person responsible for their safety.

To avoid the risk of accidents and

damage to the appliance, please

read these instructions carefully

before using it for the first time.

They contain important information

on the safety, installation, use and

maintenance of the appliance.

Safety with children

This appliance is only intended for

use by adults who have read these

instructions.

This appliance is not a toy! To avoid

Keep these instructions in a safe

place and ensure that all users are

familiar with the contents. Pass them

on to any future owner of the

appliance.

the risk of injury, keep children well

away and do not allow them to play with

it or to use the controls. They will not

understand the potential dangers posed

by it. They should be supervised

whenever you are working in the kitchen.

Correct application

Older children may use the cooker

hood only when its operation has been

clearly explained to them and they are

able to use it safely, recognising the

dangers of misuse.

This appliance is intended for

domestic use only.

Any other usage is at the owner's risk

and could be dangerous. The

manufacturer cannot be held liable for

damage resulting from incorrect or

improper use or operation.

Please be aware that on cooker

hoods with halogen lighting, the lamps

will get very hot during use and remain

hot for some time after switching off. To

safeguard against burning, keep

children well away from the lamps at all

times.

Warning and Safety instructions

Technical safety

Installation, maintenance and

repairs may only be carried out by a

Miele authorised person in accordance

with current national and local safety

regulations.

Repairs and other work by unqualified

persons could be dangerous. The

manufacturer cannot be held liable for

unauthorised work.

Before installation, check the cooker

hood for visible signs of damage.

Under no circumstances should you

use a damaged appliance. A damaged

appliance is dangerous.

Before connecting the appliance to

the mains supply, make sure that the

voltage and frequency details given on

the data plate correspond with the

on-site electricity supply, otherwise the

appliance could be damaged. Consult

a qualified electrician if in any doubt.

Faulty components must only be

replaced by genuine Miele original

parts. The manufacturer can only

guarantee the safety of the appliance

when Miele replacement parts are

used.

The electrical safety of this

appliance can only be guaranteed

when continuity is complete between it

and an effective earthing system which

complies with current local and national

safety regulations. It is most important

that this basic safety requirement is

present and tested regularly, and

where there is any doubt, the

During installation, maintenance and

repair work, the appliance must be

disconnected from the mains electricity

supply. It is only completely isolated

from the electricity supply when:

– it is switched off at the isolator, or

– the screw-out fuse is removed (in

countries where this is applicable), or

household wiring system should be

inspected by a qualified electrician.

The manufacturer cannot be held liable – the mains fuse is disconnected, or

for the consequences of an inadequate

– it is switched off at the wall socket

earthing system (e.g. electric shock).

and the plug withdrawn, or

For safety reasons, this appliance

– the fuse from the fused spur

may only be used when it has been

connection unit is withdrawn.

fully installed.

Only open the housing as described

in the instructions given in the

installation sheet and in the Cleaning

and care section of this booklet. Under

no circumstances should any other

parts of the housing be opened.

Tampering with electrical connections

or components and mechanical parts is

highly dangerous to the user, and can

cause operational faults.

Warning and Safety instructions

Do not connect the appliance to the

mains electricity supply by a

multi-socket unit or an extension lead.

These do not guarantee the required

safety of the appliance (e.g. danger of

overheating).

Using at the same time as other

heating appliances that depend on

the air from the room

Warning - danger of toxic fumes

For appliances with an external fan

motor fitted (...EXT models) the

connection of the two units must be

made using the connection cable and

the plug connectors.

These models may only be combined

with a Miele external motor.

This appliance may only be used in

mobile installations such as ships,

caravans, aircraft etc. if a risk

assessment of the installation has been

carried out by a suitably qualified

engineer.

Great care should be taken when

using the cooker hood at the same time

and in the same room or area of the

house as another heating appliance

which depends on the air in the room.

Such appliances include gas, oil, wood

or coal-fired boilers and heaters,

continuous flow or other water heaters,

gas hobs, cookers or ovens which draw

air in from the room and duct exhaust

gases out through a chimney or

extraction ducting.

In areas which may be subject to

infestation by cockroaches or other

vermin, pay particular attention to

keeping the appliance and its

surroundings in a clean condition at all

times. Any damage which may be

caused by cockroaches or other vermin

will not be covered by the guarantee.

When used in extraction mode, with or

without an external motor fitted, the

appliance draws air in from the room in

which it is installed and from

neighbouring rooms.

If there is insufficient air, an

underpressure will occur. The heating

appliance may be starved of oxygen,

impairing combustion.

Harmful gases could be drawn out of

the chimney or extraction ducting back

into the room, with potentially fatal

consequences.

Warning and Safety instructions

In order to ensure safe operation, and

to prevent gases given off by the

heating appliances from being drawn

back into the room when the cooker

hood and the heater are in operation

simultaneously, an underpressure of

0.04 mbar (4 pa) is the maximum

permissible in the room.

One of the following technical

measures may be necessary to ensure

safe operation.

– If the only way of ensuring adequate

ventilation is via an open window, a

window contact switch should be

fitted to ensure that the cooker hood

can only operate when the window is

opened sufficiently.

Take care when ventilating the room

through an open window that

ventilation is not impaired by a

closed blind or curtain.

– The cooker hood can be set up to

automatically switch on an air intake

fan or open a motorised inlet flap

when it is switched on.

– The cooker hood can be set up to

automatically switch off a heating

appliance which also depends on

the air from the room when it is

switched on.

Ventilation can be maintained by air

inlets which must not be blocked, in

windows, doors and outside wall vents,

or by other technical measures, such

as ensuring that the cooker hood can

only be switched on when the heating

appliance is switched off or vice versa.

A ventilation brick alone is not generally

sufficient to ensure safe ventilation.

The Miele DSM 400 control module

offers the possibility of combining other

components with the cooker hood (see

"Operation with Control module

DSM 400").

It is available to purchase as an

optional extra.

,The overall ventilation condition

of the dwelling must be taken into

account. If in any doubt, the advice

of a competent builder or, for gas, a

qualified gas fitter (registered with

an official gas safety body in

If in any doubt, the advice of a

competent builder or for gas , a

qualified gas fitter must be sought.

If the hood is being operated in

recirculation mode, the above

restrictions do not apply.

accordance with national safety

regulations) must be sought.

Warning and Safety instructions

Correct use

Do not use the cooker hood without

the filters in place. This way you will

avoid the risk of grease and dirt getting

into the appliance and hindering its

smooth operation.

Never use an open flame beneath

the cooker hood. To avoid the danger

of fire, do not flambé or grill over an

open flame.

When switched on, the cooker hood

could draw flames into the filter. Fat

particles drawn into the cooker hood

present a fire hazard.

The filters should be regularly

cleaned or changed as appropriate.

Saturated filters are a fire hazard. See

"Cleaning and care".

When using the cooker hood over a The cooker hood can get very hot

gas hob, ensure that any burners in use during cooking due to heat rising from

are always covered by a pan. Switch

the cooking zone off when a pan is

removed, even for a short time.

Regulate the flame so that it does not

burn up the sides of the pan.

Do not allow the pans to overheat

excessively (e.g. when using a wok).

The cooker hood can become

damaged when exposed to excessive

heat.

the hob.

Do not touch the housing or the grease

filters until the cooker hood has cooled

down.

Do not use a steam-cleaner to clean

this appliance. Steam could reach the

electrical components and cause a

short circuit.

Correct installation

Always switch the cooker hood on

when a cooking zone is in use,

Refer to the cooker or hob

manufacturer's instructions as to

whether a cooker hood may be

operated above the cooker/hob.

otherwise condensation may collect in

the hood, which could cause corrosion.

When cooking with oil or fat, chip

The minimum safety distances

pans and deep fat fryers etc, do not

leave the pans unattended. Never leave

an open grill unattended when grilling.

Overheated oil and fat can ignite and

could set the cooker hood on fire.

between the top of the cooker or hob

and the bottom of the cooker hood

given in the "Appliance dimensions"

section of this booklet must be

maintained, unless the hob

manufacturer states that a greater

safety distance is required.

If more than one cooking appliance is

fitted beneath the cooker hood, and

they have different minimum safety

distances to the cooker hood, select

the greater distance.

Warning and Safety instructions

Safety regulations prohibit the fitting

of a cooker hood over solid fuel stoves.

All ducting, pipework and fittings

must be of non-flammable material.

These can be obtained from the Miele

Spare Parts department or from

builders' merchants.

The appliance must not be

connected to a chimney or vent flue

which is in use. Neither should it be

connected to ducting which ventilates

rooms with fireplaces.

If exhaust air is to be extracted into

a chimney or ventilation duct no longer

used for other purposes, seek

professional advice.

Accessories

Only use genuine Miele spare parts

and accessories with this appliance. If

spare parts or accessories from other

manufacturers are used, this will

invalidate the guarantee, and Miele

cannot accept liability.

The manufacturer cannot be held

liable for damage caused by

non-compliance with these Warning

and Safety instructions.

Modes of operation

The cooker hood works with

. . . air recirculation:

(Applies to the DA 420 V only. A

conversion kit and charcoal filter are

required, which are available as

optional accessories: see "Technical

Data")

. . . air extraction:

The air is drawn in, cleaned by the

grease filters and directed outside.

The air is drawn in and cleaned first by

the grease filters and then by a

charcoal filter. The cleaned air is then

recirculated back into the kitchen

through grilles in the top of the cooker

hood telescopic tower.

The cooker hood is fitted with a

non-return flap, which is closed when

the cooker hood is switched off. No

exchange of room air and outside air

can take place. When the cooker hood

is switched on, the non-return flap

opens for the cooking vapours to be

blown directly outside.

Before using the cooker hood in

recirculation mode, ensure that the

charcoal filter is in place. See

"Cleaning and care".

. . . an external motor:

( ...EXT models only)

EXT models are designed to be

connected to an external motor located

outside the room.

The external motor is connected to the

cooker hood by means of a control

cable and is operated by the controls

on the cooker hood.

Guide to the appliance

aCover plate

bTelescopic tower

cCanopy

mTouch control for the grease filters

The indicator lamp for the grease filter

touch control lights up when the grease

filters need to be cleaned.

The canopy is not designed to be

used as a shelf.

This control is used to reset the

operating hours counter after cleaning

the grease filters (see "Cleaning and

care").

dGrease filters

eCharcoal filter

It can also be used to check and alter

the operating hours counter.

Available as an optional accessory for

recirculation mode (DA 420 V only)

nTouch control for the charcoal

filter

fRecirculation grille

(DA 420 V only)

(only for recirculation mode on the DA

420 V)

The indicator lamp for the charcoal filter

touch control lights up when the

charcoal filter used in recirculation

mode needs to be replaced. For this to

happen, the operating hours counter

needs to be set before the appliance is

used for the first time.

gControls

hHob lighting

iTouch control for hob lighting

This control switches the lighting on

and off, and is also a dimmer switch.

The control is used to reset the

operating hours counter after replacing

the charcoal filter (see "Cleaning and

care").

jOn/Off touch control for the fan

kTouch controls to select the fan

power level

It can also be used to check and alter

the operating hours counter.

lTouch control for the run-on

option

oControls for raising and lowering

the canopy

The fan can be set to switch off

automatically after either 5 or 15

minutes.

The height of the canopy can be

adjusted by up to 260 mm (this can be

extended to 300 mm, see "Installation").

For information about using the

appliance, see "Operation".

Miele|home

Con|ctivity

– When the hob is switched on the

cooker hood lights and the fan also

comes on.

– During cooking the cooker hood

automatically sets its power level

according to the number of cooking

zones in operation and their power

levels.

– After switching the hob off the fan

and the hob lighting will switch off

automatically after a period of time.

For detailed information about this

function please read the separate

instruction booklet supplied with the

XKM 2000 DA communication module.

This cooker hood is communication

enabled.

Communication module XKM 2000 DA

a, available as an optional extra,

enables the operation of the cooker

hood to be automatically controlled by

the operating status of a Miele electric

hob with onset controls.

The communication module is fitted to

the cooker hood in the area of the

motor and is connected to the controls

of the cooker hood.

This module must be installed by a

Miele service technician or suitably

qualified electrician.

For communication to take place, the

hob must be fitted with communication

module XKM 2000 KM b.

The hob transmits information about its

operating status to the cooker hood via

the household power supply

(Powerline) c.

Use

To switch the fan on

Automatic switch-off of the Intensive

setting

You can set the Intensive setting so that

it only runs for 10 minutes before

reverting automatically to level III.

^ Press the On/Off touch control.

^ To set this option, both the fan and

the hob lighting must be switched off.

The fan runs at power level "II".

The indicator lamp will come on.

If the cooker hood has been

connected to a window contact

switch via the DSM 400 control

module, then the fan cannot be

switched on if the window is shut.

The indicator lamp will flash.

^ Press the run-on option touch control

for approximately 10 seconds. The

first fan setting indicator will light up.

^ Then press, one after the other,

– the hob lighting touch control,

– the – touch control, and

To select a power level

^ Use the – / + controls to select the

power level required.

Touch control + = higher setting

Touch control – = lower setting

Depending on the intensity of the

cooking vapours, levels I to III (green

indicator lamps) are usually sufficient

for normal cooking.

– the hob lighting touch control again.

Intensive setting

When frying or cooking food with a

strong aroma, you may wish to select

the Intensive setting (yellow indicator

lamp) for a short period.

Use

Run-on option

It is advisable to run the fan for a few

minutes after cooking has finished to

neutralise any lingering odours in the

air, whether you are using air extraction

or recirculation mode.

The indicator lamps for fan power levels

I and IV will flash if the automatic

switch-off of the Intensive setting is not

activated.

The fan can be set to switch off

automatically after either 5 or 15

minutes:

^ Press the + touch control to activate

automatic switch-off.

The indicator lamps for fan power

levels I and IV will now light up

constantly.

Press the – touch control to

deactivate the automatic switch-off

function.

^ After cooking has finished, press the

run-on option touch control whilst the

fan is still running.

– Press once = The fan will switch off

after 5 minutes (left-hand indicator

lamp).

^ Press the run-on option touch control

to confirm your selection.

– Press twice = The fan will switch off

after 15 minutes (right-hand indicator

lamp).

If you do not confirm your selection

within 4 minutes, the cooker hood will

automatically revert to the original

setting.

To switch off the run-on option, press

the run-on option touch control again.

The appliance will then not switch off

automatically.

To switch the fan off

^ Press the On/Off touch control to

switch the fan off.

The indicator lamp will go out.

Use

To switch the lighting on

Safety cut-out

The hob lighting can be switched on

and off independently of the fan.

Should the cooker hood be left on, the

fan will switch off automatically after 10

hours. The lighting will remain on.

^ Briefly press the lighting touch

control to switch on the hob lighting.

^ Pressing the On/Off touch control will

switch the fan back on again.

The indicator lamp will come on.

The lighting will switch on at maximum

brightness.

Dimming the lighting

The brightness of the lighting can be

adjusted.

^ With the lighting switched on, press

and hold the hob lighting touch

control in.

The brightness will gradually dim until

you release the touch control.

^ Press the touch control in again to

increase the brightness to the level

required and then release it.

If you keep the touch control pressed

in, the light will continually change

between bright and dim.

To switch the lighting off

^ Press the hob lighting touch control

briefly to switch the lighting off.

The indicator lamp will go out.

Use

Filter operating hours counter

Reading the filter operating hours

counter

The number of hours the appliance has

been in operation is stored in memory.

To check the percentage of time set

already used:

The indicator lamp for the grease filter

touch control will come on after 30

hours of operation. The grease filters

must then be cleaned.

^ Press the On/Off touch control to

switch the fan on.

Afterwards, the filter operating hours

counter must be reset.

^ To do this, press and hold the grease

filter touch control for about 3 seconds.

^ Press and hold the grease filter or the

charcoal filter touch control.

The indicator lamp for the touch control

will go out.

For recirculation mode, the operating

hours counter for the charcoal filter

needs to be set to the required time

(see "Setting and altering the charcoal

filter operating hours counter").

One or more of the indicator lamps for

the – / + touch controls will flash.

The number of flashing lamps shows

the percentage of the operating time

which has already been used up.

1 lamp

2 lamps

3 lamps

25 %

50 %

75 %

The indicator lamp for the charcoal filter

touch control will light up after the

cooker hood has operated for the

4 lamps = 100 %

number of hours set. The charcoal filter

must then be replaced with a new one.

The number of operating hours used

remains in the memory, even when the

appliance is switched off or there is a

power cut.

Afterwards, the filter operating hours

counter must be reset.

^ Press the charcoal filter touch control

for about 3 seconds.

The indicator lamp for the touch control

will go out.

Use

Filter operating hours counter

You can set the operating hours

counter to suit the type of cooking you

do.

The – / + control lamps show the time

which has been set:

1st lamp from the left = 20 hours

2nd lamp from the left = 30 hours

3rd lamp from the left = 40 hours

4th lamp from the left = 50 hours

– Select a short time if you roast or fry

a lot.

– If you use very little fat for cooking,

select a longer time.

– If you only cook occasionally we

recommend that you still select a

short time, because grease which

has built up gradually over a long

period of time will harden on the

grease filter and make cleaning more

difficult.

^ Use the – / + touch controls to select

the desired time.

^ Confirm the selection by pressing the

grease filter touch control.

Altering the grease filter operating

hours counter

All the indicator lamps will go out.

The operating hours counter for the

grease filter is set at 30 hours. The time

set can be lengthened or shortened:

you can choose 20, 30, 40 or 50 hours.

If you do not confirm your selection

within 4 minutes, the cooker hood

will automatically revert to the

original setting.

^ Press the On/Off touch control to

switch the fan off.

^ Press the run-on option touch control

and the grease filter touch control at

the same time.

The indicator lamp for the grease filter

touch control and one of the – / + touch

control lamps will flash.

Use

Setting and altering the charcoal

filter operating hours counter

^ Use the – / + touch controls to select

the desired time.

(with recirculation mode)

The charcoal filter is needed for

recirculation mode.

The cooker hood is set at the factory for ^ Confirm the selection by pressing the

extraction mode. On delivery, the

operating hours counter for the

charcoal filter is set to unlimited.

charcoal filter touch control.

All the indicator lamps will go out.

If you do not confirm your selection

within 4 minutes, the cooker hood

will automatically revert to the

original setting.

For recirculation mode, the operating

hours counter needs to be set to the

required time:

^ Press the On/Off touch control to

switch the fan off.

^ Press the run-on option touch control

and the charcoal filter touch control

at the same time.

The indicator lamp for the charcoal filter

touch control and one of the lamps

above the – / + touch controls will flash.

The – / + control lamps show the time

which has been set:

1st lamp from the left = 120 hours

2nd lamp from the left = 180 hours

3rd lamp from the left = 240 hours

4th lamp from the left = unlimited

Use

Adjusting the height of the

canopy

The height adjustment feature on the

canopy can be used to –

– adapt the height of the hood to suit

the installation conditions.

– adjust the working area underneath

the hood to the height of the user.

– maximise vapour extraction by

lowering the canopy during

particularly intensive cooking.

– create more working space above

the hob by raising the canopy when

required.

The height of the canopy can be

adjusted by up to 260 mm (this can be

extended to 300 mm, see “Installation”).

^ The canopy can be raised or lowered

by touching the Up or Down controls

briefly.

^ Pressing the control again stops the

canopy.

If it is not stopped, the canopy will

automatically be raised or lowered to its

fullest extent.

Repeated use of the height

adjustment feature over several

minutes will cause it to cut out. It can

be used again after a pause.

Cleaning and care

Avoid:

,^{Before carrying out any cleaning}

or maintenance work, disconnect

the cooker hood from the mains

supply. Ensure that:

– it is switched off at the isolator, or

– the fuse is withdrawn from the

fused spur connection unit, or

– the mains fuse is disconnected, or

– the screw-out fuse is removed (in

countries where this is applicable).

– cleaning agents containing soda,

acids, chlorides or solvents,

– abrasive cleaning agents, e.g.

powder cleaners or cream cleaners

and abrasive sponges, as well as pot

scourers or sponges which have

been used previously with abrasive

cleaning agents.

These will damage the surface

material.

A range of Miele branded cleaning and

conditioning agents are available to

order through your Miele Dealer /

Chartered Agent, the Miele Spare Parts

Department, or via the internet on

www.miele-shop.com.

Important for appliances with

stainless steel housing

(This infomation does not apply to the

controls).

Stainless steel surfaces can be cleaned

using the Miele E-cloth, or with a

proprietary non-abrasive cleaning

agent designed specifically for use on

stainless steel.

Housing

General notes

The surfaces and controls are

susceptible to scratches and

abrasions. Please observe the

following cleaning instructions.

To help prevent re-soiling, a

conditioning agent for stainless steel

can also be used. Apply sparingly,

following the instructions on the label.

^ All external surfaces and controls can

be cleaned with warm water and a

small amount of washing-up liquid

applied with a well wrung-out soft

sponge or cloth.

If too much conditioning agent is

used traces of it may appear in the

area where the canopy rises and

falls.

^ Wipe the surfaces dry using a soft

cloth.

Do not use too much water when

cleaning the controls. Water could

penetrate into the electronics and

cause damage.

Cleaning and care

Controls

Grease filters

Re-usable metal filters are fitted which

remove solid particles (oil, dust, etc.)

from the kitchen vapours, preventing

soiling of the cooker hood.

The controls may suffer

discolouration or damage if soiling is

left on them for too long. Remove

soiling straight away.

Observe the General notes on cleaning

earlier in this section.

The grease filters should be cleaned

regularly (at least every 3-4 weeks) to

avoid a build-up of grease.

Do not use stainless steel cleaning

agents on the controls.

However, they should be cleaned

immediately if the grease filter touch

control lamp comes on.

,An oversaturated filter is a fire

hazard.

^ To take out the grease filters, release

the locking clip on the filter, lower the

filter 45°, unhook it at the back and

remove it.

To avoid damaging the filter or the

hob below, make sure you hold the

filter securely at all times when

handling it.

Cleaning and care

Cleaning the grease filters by hand

^ When removing the filters for

cleaning, also clean off any residues

of oil or fat from the now accessible

housing to prevent the risk of these

catching fire.

^ Clean the filters with a soft nylon

brush in a mild solution of hot water

and a small amount of washing-up

liquid.

Do not use:

– undiluted washing-up liquid,

– cleaning agents containing

descaling agents,

– powder cleaners, cream cleaners or

abrasive all-purpose cleaning

agents,

When putting the grease filters back

in position, ensure that the locking

clips are facing down towards the

hob.

– oven sprays.

Cleaning the grease filters in the

dishwasher

If the grease filters are inadvertently

replaced upside down, insert a small

screwdriver blade into the slits to

disengage the clip.

^ Place the filters as upright as

possible in the lower basket, with the

short sides upright, and wash on a

65°C programme, ensuring the spray

arm is not obstructed. If a Miele

dishwasher is being used, select the

Sensor wash programme.

^ After replacing the grease filters,

press the grease filter touch control

for approximately 3 seconds to re-set

the operating hours counter.

^ Use a mild dishwasher detergent.

The indicator lamp will go out.

Depending on the cleaning agent

used, cleaning the filters in a

dishwasher can cause permanent

discolouration to the surface.

However, this will not affect the

functioning of the filters in any way.

If the grease filters are cleaned before

the operating hours counter has

reached its maximum, the grease filter

touch control should be pressed for

approximately 6 seconds to reset the

counter.

^ After cleaning, leave the filters to dry

on an absorbent surface before

replacing them.

Cleaning and care

Fitting and replacing the

charcoal filter

Always replace the charcoal filter im-

mediately if

If the cooker hood is connected for

recirculation, a charcoal filter must be

inserted in addition to the grease filters.

It is designed to absorb cooking

odours.

– the indicator lamp for the charcoal

filter touch control lights up,

It is fitted in the canopy above the

grease filters.

– if it is no longer effective in absorbing

kitchen odours.

New filters can be purchased from

your Miele Dealer / Chartered Agent

or from the Miele Spare Parts

Department.

See back cover for contact details,

and "Technical data" for the model

number of the filter.

It should, however, be replaced at least

every 6 months.

Used charcoal filters can be disposed

of with the normal household waste.

^ After fitting the new charcoal filter,

press the charcoal filter touch control

for approximately 3 seconds to re-set

the operating hours counter.

^ Before fitting or replacing a charcoal

filter, the grease filters must first be

taken out (see previous section for

instructions on how to do this).

The indicator lamp will go out.

^ Take the charcoal filter out of its

packaging.

^ If a charcoal filter is replaced before

the operating hours counter has

reached its maximum, the charcoal

filter touch control should be pressed

for approximately 6 seconds to reset

the counter.

^ Insert the charcoal filter into the

canopy.

When fitting for the first time:

^ Set the operating hours counter to

suit your requirements (see

"Operation").

Cleaning and care

Changing a halogen lamp

^ Before any cleaning or maintenance

work, disconnect the cooker hood

from the mains supply. Ensure that

– it is switched off at the isolator, or

– the screw-out fuse is removed (in

countries where this is applicable).

,^{Exercise caution when changing}

halogen lamps. They get very hot

during use and remain hot for some

time after being switched off. Let

them cool down before you change

them.

Do not touch the surface directly

when changing a lamp, as grease

particles from your fingers will

adhere to the surface and damage

it. Please follow the manufacturer's

instructions.

^ To access the halogen lamp, push

the lamp cover gently upwards. The

cover will open and can be pulled

down.

^ Pull the old halogen lamp out of the

connection socket and replace it with

a new one (20 W, G 4 fitting).

^ Push the cover back up and make

sure it clicks into place.

After Sales Service

In the event of a fault which you cannot

correct yourself, or if the appliance is

under guarantee, please contact:

– Your Miele Dealer / Chartered Agent

– The Miele Customer Contact Centre

(see back cover for address).

When contacting your Dealer or Miele,

please quote the model and serial

number of your appliance. These are

shown on the data plate which is visible

when the grease filter is removed.

For G.B.: Please note that telephone

calls may be monitored and

recorded for training purposes.

Appliance dimensions

1) Cut-out for feeding through the

exhaust ducting, the mains cable and,

with ... EXT models, the connection

cable to the external motor

In recirculation mode, only the mains

cable is required.

2) Height range for appliance in

extraction mode (the appliance is

delivered with this height range as

standard).

3) Height range for appliance in

recirculation mode

4) Possible height range for appliance

in extraction mode (see "Installation").

5) Ventilation grille positioned at the top

for recirculation

DA 420 V

Exhaust connection C 150 mm (not

needed for recirculation mode)

(Ceiling fixing viewed from above)

DA 424 V

(Ceiling fixing viewed from above)

Appliance dimensions

Safety distance between hob and

cooker hood (S)

The minimum safety distances

between the top of a cooker or hob

and the bottom of the cooker hood

are as follows, unless a greater

distance is specified by the

manufacturer of your cooking

appliance:

–

550 mm (GB), 600 mm (AU, NZ)

above electric hobs and

cookers,

–

650 mm above an open grill or

deep fat fryer,

650 mm above gas hobs and

cookers.

If this cooker hood is installed above

a Miele Wok CS 1028 CombiSet

appliance, a minimum safety

distance of 760 mm must be

maintained between the burner and

the lower edge of the cooker hood.

For further advice, see "Warning and

Safety" instructions.

If the distance falls below the

recommended safety distance when

the canopy is lowered, the maximum

interval it is allowed to be lowered must

be re-set during installation (see

"Installation").

Installation

,^{Before installation, it is important}

to read the information given on the

following pages as well as the

"Appliance dimensions" and the

"Warning and Safety instructions" at

the beginning of this booklet.

This is particularly crucial when

using the cooker hood at the same

time as a heating appliance that

relies on oxygen from the same

room to avoid the danger of toxic

fumes building up.

2 screws M4 x 8 mm

for securing the tower.

4 spacers to use in the event of an

uneven ceiling.

Installation instructions

See enclosed Installation sheet for

instructions on how to install this

appliance.

1 floating bracket to give a choice of

position for the exhaust cut-out in the

ceiling.

Assembly parts

4 screws 8 x 60 mm with

4 washers and

4 plugs S 10 to secure the cover plate

to the ceiling

1 hose clip for securing the exhaust

ducting to the exhaust stub.

Special installation instructions

for recirculation mode

,The screws and plugs are for use

in concrete ceilings only.

For other types of construction,

alternative suitable fixings will be

required.

In order to use the cooker hood in

recirculation mode, it has to be fitted

with a special conversion kit which is

available from the Spare Parts

Make sure the ceiling is strong

enough to bear the weight of the

cooker hood.

Department (see "Technical data"). It is

supplied with its own fitting instructions.

After the cooker hood has been

installed, the charcoal filter has to be

fitted, and the operating hours counter

has to be set. See "Cleaning and Care"

and "Filter operating hours counter".

Installation

Extending or limiting the adjustment

range

,^{Ensure that the tower is held}

securely while carrying out the

following steps. Danger of inury.

The height range for the appliance can

be extended or limited by moving the

limit switch.

It may be necessary to do this if

– the distance between the hob and

the canopy when it is lowered is less

than the minimum safety disance

required. By moving the limit switch,

the height range for the appliance

can be limited (the canopy will not be

lowered as far).

– a greater adjustment range is

required (the canopy will be lowered

further). A maximum appliance

height of 1030 mm is possible (for

extraction mode only, not possible

for recirculation mode).

dai2258

^ Push the tower upwards.

^ Install the cooker hood according to

the installation instructions supplied.

^ Press the Down button to lower the

canopy. The canopy will be lowered

to its fullest extent.

dai2259

^ Now secure the tower with the screw

you removed earlier.

dai2257

^ Remove the grease filters.

^ Remove the cooker hood tower fixing

screw.

Installation

dai2262

^ Secure the limit switch opposite the

guide on the telescopic tower (see

illustration).

^ Raise and lower the canopy and

check that the limit switch is working.

dai2260

^ Loosen the top limit switch.

^ Remove the safety screw and push

the tower downwards.

^ If a greater safety distance "S"

between the canopy and the hob is

required a, raise the canopy until the

required safety distance has been

reached.

dai2264

^ Then secure the tower with the safety

screw again.

^ If a greater adjustable range is

required b, lower the canopy. A

maximum appliance height of 1030

mm is possible.

Replace the grease filters.

Electrical connection

If the switch is not accessible after

installation (depending on country), an

additional means of disconnection must

be provided for all poles.

All electrical work should be

undertaken by a suitably qualified

and competent person in strict

accordance with current national

and local safety regulations.

(BS 7671 in the UK).

For extra safety it is advisable to install

a residual current device (RCD) with a

trip current of 30 mA.

Installation, repairs and other work

by unqualified persons could be

dangerous, for which the

Important

AUS: This appliance is supplied for

connection to an a.c. single phase

230 V, 50 Hz supply.

manufacturer cannot be held liable.

Ensure power is not supplied to the

appliance until after installation or

repair work has been carried out.

The wires in the mains lead are

coloured in accordance with the

following code:

Green/yellow = earth

= neutral

= live

Do not connect the appliance to the

mains electricity supply by an

extension lead. These do not

guarantee the required safety of the

appliance.

Blue

Brown

WARNING:

THIS APPLIANCE MUST BE

EARTHED

The voltage and connected load are

given on the data plate. This is visible

when the grease filters have been

removed. Ensure that these match the

household mains supply.

Connection of this appliance should be

made via a suitable isolator or a double

pole fused spur connection unit which

complies with national and local safety

regulations and the On-Off switch

should be easily accessible after the

appliance has been built in.

When switched off there must be an

all-pole contact gap of 3 mm in the

switch (including switch, fuses and

relays according to EN 60 335).

Operation with DSM 400 control module

The Miele DSM 400 control module can

be used to combine the cooker hood

with other components.

If the control module is

disconnected in order to operate the

cooker hood without the window

contact switch (e.g. after moving

house) the cooker hood electronics

must be reset by a Miele service

technician.

It enables the following:

Connection to a window contact

switch

If adequate ventilation to the room can

only be ensured by having a window

open when the cooker hood is in use at

the same time as a heating appliance

which depends on the air from the

same room, then the control module

can be used to connect a window

contact switch (not supplied) to the

appliance.

Potential free connection

This enables a further appliance to be

controlled by the switch setting on the

cooker hood fan.

– For instance it can be used to ensure

a sufficient supply of fresh air when

the cooker hood and a heating

appliance which also depends on

the air in the room are being used

together, by switching on an air

intake fan, or opening a motorised

inlet flap as soon as the cooker hood

fan is switched on.

Once connnected, the cooker hood can

only be operated when the window is

sufficiently open (see also "Warning

and Safety instructions").

When the window is closed, the cooker

hood fan cannot be switched on. The

indicator lamp for the On/Off touch

control on the cooker hood will flash.

It is important to ensure that the fan

power is sufficient and that the air

intake has a suitable cross-sectional

diameter.

The same applies to operation with an

external motor (depending on model).

The cooker hood lighting is not affected

by this.

– If a sufficient air intake cannot be

guaranteed, then the potential free

contact will enable a heating

...EXT models can also be connected to

a window contact switch.

appliance, which depends on air in

the same room as a cooker hood, to

be switched off when the cooker

hood is in operation.

Take care when ventilating the room

through an open window that ventilation

is not impaired by a closed blind or

curtain.