Instruction Manual
UC3030A
UC3530A
UC4030A
UC4530A
UC3530AP
UC4030AP
Important:
Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations!
Keep this instruction manual!
Delivery inventory
1
2
3
1. Electric chain saw
2. Guide bar
3. Saw chain
4
4. Cord grip for electric cord
5. Chain protection cover
6. Instruction manual (not shown)
5
In the case that one of the parts listed should not be included in
the delivery inventory, please, consult your sales agent.
EU Conformity Declaration
The undersigned, Yasuhiko Kanzaki, declare that the MAKITA
machines,
Packing/Disposal
The MAKITA electric chain saw will be delivered in a protective
cardboard box to prevent transport damages.
Type: ꢀꢀ6
EU prototype test certificate No.
Cardboardisabasicrawmaterialandisthereforeconsequently
reuseable or suitable for recycling (waste paper recycling).
UC3030A
M6 06 07 24243 068
UC3530A / AP M6 06 07 24243 068
UC4030A / AP M6 06 07 24243 068
UC4530A
M6 06 07 24243 068
manufactured by DOLMAR GmbH, Jenfelder Str. 38, ꢀꢀ045
Hamburg, Germany, conforms to the basic safety and health
requirements of the applicable EU guidelines:
Be a good steward of the environment! Do not dispose of
electrical appliances with the household trash!
EU Machinery Directive 98/37/ EG, EU EMC Directive 89/336/
EWG(modifiedby91/263/EWG,92/31/EWGand93/68/EWG),
EU low voltage Directive 73/ꢀ3 EWG (modified by 93/68/EWG,
Outdoor Noise Directive ꢀ000/14/EG.
The most important standards applied to properly meet the
requirements of the above EU Directive were: EN 60745-ꢀ-13,
EN 61000-3-ꢀ, EN 61000-3-3, EN 55014-1, EN 55014-ꢀ.
If the saw is no longer operable or repairable, ask the appro-
priate waste disposal authority about the proper means of dis-
posal.
In order to preclude any hazard to other persons from a de-
fective electrical appliance, cut off the power cord next to the
housing.
The conformity assessment procedure ꢀ000/14/EG was per-
formed per Annex V. The measured sound power level (Lwa)
is 101,5 dB(A). The guaranteed sound power level (Ld) is 103
dB(A).
CArEfUL! Before cutting off the power cord, pull the
plug. otherwise you can be exposed to a life-threatening
shock!
The EC-Type-Examination Certificate per 98/37/EG was
performed by: TÜV Süd Product Service GmbH, Zertifizier-
ungsstelle, Ridlerstr. 31, D-80339 München.
Yasuhiko Kanzaki CE ꢀ006
Intended use
Electric saws
This electric saw may be used only for sawing wood. It is in-
tended for occasional use in thin wood, caring for fruit trees,
felling, removing limbs, and trimming to length.
Managing Director
MAKITA InTErnATIonAL EUroPE LTD.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
Persons who may not sue the saw:
This saw must not be used by persons who are not familiar
with this instruction manual, children, young people, or anyone
under the influence of alcohol, drugs or medication.
Responsable person manufacturer:
Makita Corporation Anjo Aichi Japan
3
SAfETy PrECAUTIonS
General precautions
-
Toensurecorrectoperationtheuserhastoreadthisinstruc-
tion manual to make himself familiar with the characteristics
of the electric chain saw. Users insufficiently informed will risk
danger to themselves as well as others due to improper han-
dling.
-
It is recommended only to lend the electric chain saw to people
who have proven to be experienced with electric chain saws.
Always hand over the instruction manual.
-
-
-
First users should ask the dealer for basic instructions to become
familiarized with the characteristics of engine powered sawing.
Familiarize yourself with the use of an electric chain saw by
cutting off lengths from a log on a sawhorse.
Children and young persons aged under 18 years must not be
allowed to operate the electric chain saw. Persons over the age
of 16 years may, however, use the chain saw for the purpose
of being trained while under supervision of a qualified trainer.
Use electric chain saws always with the utmost care and atten-
tion.
1
-
-
Operate the electric chain saw only if you are in good physical
condition. Perform all work calm and carefully. The user has to
accept liability for others.
-
Neverusetheelectricchainsawaftertheconsumptionofalcohol
or drugs or medication.
ꢀ
Personal protective equipment
-
-
-
In order to avoid head, eye, hand or foot injuries as well as
to protect your hearing the following protective equipment
must be used during operation of the electric chain saw.
Thekindofclothingshouldbeappropriate, i. e. itshouldbetight-
fitting but not be a hindrance. Do not wear jewellery or clothing
which could become entangled with bushes or shrubs.
The protective helmet (1) is to be checked in regular intervals
for damage and is to be replaced after 5 years at the latest. Use
only approved protective helmets.If you have long hair wear a
hairnet.
-
The face shield (ꢀ) of the protective helmet (or the goggles)
protect against sawdust and wood chips. During operation of
the electric chain saw always wear a goggle or a face shield to
prevent eye injuries.
3
-
-
Wear adequate noise protection equipment (ear muffs (3),
ear plugs, etc.). Octave brand analysis upon request.
The protective brace and bib overall (4) is made of a nylon
structure with ꢀꢀ layers and protects against cuts. We strongly
recommenditsuse. Inanycasewearalongpairoftrousersmade
of solid material during operation of the electric chain saw.
Protective gloves (5) made of thick leather are part of the pre-
scribed equipment and must always be worn during operation
of the electric chain saw.
Duringoperationoftheelectricchainsawsafetyshoesorboots
(6) fitted with anti skid sole, steel toe caps and protection for
the leg are always to be used. Safety shoes equipped with a
protective layer provide protection against cuts and ensure a
secure footing.
-
-
4
Putting into operation
-
Do not operate the electric chain saw when it rains or in wet or
moist environment because the motor is not waterproof.
If the electric chain saw is moist, it must not be put into opera-
tion.
-
-
-
Avoid physical contact with grounded surfaces.
Do not operate the electric chain saw next to inflammable gases
or dusts. Explosion hazard.
-
-
Do always lead the power supply cable behind the user. Take
carethatthecableisnotclampedorcutbysharp-edgedobjects.
Lay the cable such that nobody is endangered.
Insert the plug only into safety sockets with approved installa-
tion. Make sure that the mains voltage corresponds to that on
the identification plate. Back-up fuse 16 A. If the saw is going to
be used outdoors connect it to a fault-current (FI) circuit breaker
with max. 30 mA triggering current.
5
4
-
-
Pay attention to the diameter of the extension cable. When using
a cable roll the cable should be completely wound off. Use only
extension cords that meet the specifications in “Technical data”.
If using the saw out of doors make sure that the extension cord is
approved for such use.
Before starting work the electric chain saw must be checked
for perfect function and operating safety according to the
prescriptions.
Checkespeciallythefunctionofthechainbrake,thecorrectmounting
of the guide bar, the correct sharpening and tightening of the saw
chain,thefirmmountingofthesprocketguard,theeasymotionofthe
powerswitch,thefunctionofthelockingbutton,thegoodmechanical
condition of cable and plug and the cleanliness and dryness of the
handles.
6
-
Put the electric chain saw only into operation if it is completely as-
sembled. Neverusetheelectricchainsawwhenitisnotcompletely
assembled.
-
-
Remove the adjusting tool before switching the saw on.
All protective installations and guard supplied with the chain saw
during operation.
-
Make sure that there are no children or other persons within the
working range. Also pay attention to any animals in the working
vicinity (6).
-
-
Before switching on the electric chain saw ensure that you have a
safe footing.
When switching on the electric chain saw always hold it with
both hands. Take the back handle with the right hand and the
tubular handle with the left hand. Hold the handles tightly with your
thumbs facing your fingers. The bar and chain must indicate away
from your body (7).
7
-
-
Switch on the saw only in the manner described in this manual. Do
not overload your saw. It will work better and more safely if you use
it within its intended performance range.
Switchofftheelectricchainsawimmediatelyifyouobserveachange
in its operating behavior.
CAUTIon: When releasing the power switch the chain keeps
on running for a short period of time (free-wheeling).
Protect the power cord from heat, oil and sharp edges.
-
-
Route the power cord in such a way that in cannot get caught in
branches or other objects during sawing.-If the cable is being
damaged or cut, pull out the power supply plug immediately.
Ifthesawingdeviceishitbystones,nailsorotherhardobjects,pullout
the power supply plug and check the sawing device immediately
Pulloutthepowersupplyplugbeforecheckingthechaintension,
tightening the chain, replacing it or clearing malfunctions.
When stopping work or leaving the electric chain saw switch off the
chain saw and pull out the power supply plug. Put the electric chain
saw in a safe location to prevent danger to others.
-
-
-
8
● device malfunction
● maintenance
● refill oil
-
-
-
-
For refilling the oil tank the power supply plug must be pulled out.
Do not smoke or light open fires.
Avoid skin or eye contact with mineral oil products. Always wear
gloves when refilling the oil tank.
●
sharpen the saw chain
Takecarethatnochainoiloozesintothesoil(environmentalprotec-
tion). Use an appropriate base.
If oil has been spilt, clean the electric chain saw immediately.
● stop
● transport
●
shutdown
Working behavior/method of working
9
-
-
-
Do not work on your own. There must be someone around in case
of an emergency (within shouting distance).
During sawing operation always hold the electric chain saw with
both hands. Thus you will be able to guide it safely.
Only use the electric chain saw during good light and visibility pe-
riods. Be aware of slippery or wet areas, and of ice and snow (risk
of slipping). The risk of slipping is extremely high when working on
recently peeled wood (bark).
-
Never work on unstable surfaces. Make sure that there are no
obstacles in the working area, risk of stumbling.Always ensure that
you have a safe footing.
-
-
-
Never saw above your shoulder height.
Never saw while standing on a ladder.
Never climb up into trees to perform sawing with the electric chain
saw.
Never bend forward by far to perform sawing.
-
10
5
-
Guide the electric chain saw in such a way that no part of your
body is within the elongated swiveling range of the saw (11).
-
-
Use the electric chain saw for sawing wood only.
Do not let the chain touch the ground when it is running. If you
are cutting wood lying directly on the ground, turn it over before
completing the cut so that you do not cut into the ground.
-
-
Clear the area of the cut of foreign objects such as sand, stones,
nails, wire etc. Such objects can damage the blade and cause
dangerous kickback.
When sawing precut timber or thin woods use a safe support
(sawing jack,1ꢀ). When sawing precut timber or thin pieces use
a stable support (sawhorse, 1ꢀ). Do not saw stacked timber!
Do not let another person steady the timber, and do not steady
it with your foot!
11
-
-
Secure round timber.
Z
When working on slopes, always work facing the slope.
-
-
for performing crosscuts the toothed ledge (1ꢀ,Z) must be
applied to the timber to be cut.
Before performing a crosscut firmly apply the toothed ledge to
the timber, only then can the timber be cut with the chain run-
ning. For this the electric chain saw is lifted at the back handle
and guided with the tubular handle. The toothed ledge serves
as a center of rotation. Continue by slightly pressing down the
tubularhandleandsimultaneouslypullingbackwardstheelectric
chain saw. Apply the toothed ledge a little bit deeper and once
again lift the back handle.
1ꢀ
-
-
-
The sawing device must be running whenever you remove the
electric chain saw from the timber.
When performing several cuts the electric chain saw must be
switched off in between.
When the timber must be pierced for cutting or longitudinal
cuts are to be performed it is urgently recommended to
have these works carried out by specially trained persons
only (high risk of kickbacks).
-
-
For performing longitudinal cuts (13) apply the sawing device
at an angle which is as small as possible. Be very careful when
carrying out this kind of work because the toothed ledge cannot
be used.
13
When cutting with the bottom edge of the bar the electric chain
saw may be pushed in the direction of the user if the chain is
clamped. For this reason use the top edge of the bar whenever
possible. The electric chain saw will then be pushed away from
your body (14).
-
If the timber is not free of tension (15), first cut the pressure
side (A). Then the crosscut can be performed on the tension
side (B). Thus clamping of the bar is avoided.
-
-
-
-
-
Be very careful when cutting splintery wood. Cut pieces of wood
may be pulled along (risk of injuries).
Neverusetheelectricchainsawforliftinguporremovingpieces
of wood or other objects.
When releasing the tension the electric chain saw should be
supported on the trunk (risk of kickbacks).
14
Tension releasing works must be carried out by trained
persons. High risk of injuries.
Be aware of branches under tension. Do not cut free branches
from below.
-
-
Never perform tension releasing works standing on the trunk.
Do not use the electric chain saw for works in the forest, i.
e. for cutting down trees or carrying out tension releasing
works. The user's mobility and safety necessary for this
kind of work are not guaranteed due to the cable connec-
tion.
15
6
CAUTIon:
Do not fell or debranch trees unless you are specially
trained for it! There is a high risk of injury! Make sure to
follow local regulations.
Before cutting down a tree ensure that
a) only those persons are within the working range which are
actually involved in cutting down the tree
45°
45°
-
21
2
b) allpersonsinvolvedinthefellinghaveanunhinderedretreat
route (the retreat path should be about 45° diagonally and
to the rear away from the direction of fall). Be aware of the
increased risk of stumbling from electric cables!
c) the bottom part of the trunk is free from foreign bodies, un-
derbrush and branches. Make sure to have a safe footing
(risk of stumbling).
= cutting down range
16
d) the next working place is at least ꢀ 1/ꢀ tree lengths away
(16). Before cutting down the tree check the direction of fall
and make sure that there are neither other persons nor any
objects within a distance of ꢀ 1/ꢀ tree lengths (16).
Judging the tree:
Direction of hanging - loose or dry branches - height of the tree
- natural hang over - is the tree rotten?
Take into account the direction and the velocity of the wind.
If strong gusts are occuring, do not perform any cutting down
works.
-
-
-
-
o
45
A
A
Cutting the roots:
Start with the strongest root. First perform the vertical and then
the horizontal cut.
Notching the trunk (A, 17):
The notch determines the direction of fall and guides the tree.
The trunk is notched perpendicular to the direction of fall and
penetrates 1/3 -1/5 of the trunk diameter. Perform the cut near
the ground.
17
-
When correcting the cut always do so over the whole width of
the notch.
-
-
Cut down the tree (B, 18) above the bottom edge of the notch
(D). The cut must be exactly horizontal. The distance between
both cuts must be approx. 1/10 of the trunk diameter.
The material between both cuts (C) serves as a hinge. Never
cut it through, otherwise the tree will fall without any control.
Insert felling wedges in the cut (B, 18) in good time.
Secure the cut only with wedges made of plastic or aluminium.
Do not use iron wedges.
When cutting down a tree always stay sideways of the falling
tree.
When withdrawing after having performed the cut down be
aware of falling branches.
C
-
-
-
-
D
B
B
When working on a sloping ground the user of the electric chain
saw must stay above or sidewards of the trunk to be cut or the
already cut down tree.
C
18
-
Be aware of trunks which may roll towards you.
Kickback
When working with the electric chain saw dangerous kickbacks
may occur.
-
-
-
Kickback occurs when the tip of the blade(especially the top
quarter) inadvertently comes into contact with wood or other
solid objects.
In this case the electric chain saw is thrown without any control
and with high energy potentials in the direction of the user (risk
of injuries).
In order to prevent kickbacks follow the indicated instruc-
tions:
-
-
Never apply the end of the bar when starting to make a cut.
Always observe the end of the bar.
Never use the bar end for sawing. Be careful when continuing
to cut.
-
-
When starting to perform a cut the chain must be running.
Ensurethatthechainisalwayssharpenedcorrectly.Payspecial
attention to the hight of the depth limiter (for detailed information
see the chap. "Sharpening the saw chain").
Never cut several branches at the same time. When cutting a
branch ensure that no other branch is touched.
When crosscutting a trunk be aware of the trunks next to it. It
is recommended to use a saw jack.
19
-
-
7
Transport and storage
-
Carry the electric chain saw with the tubular handle. The
saw bar indicates backwards. never carry or transport
the electric chain saw with the chain running.
Never carry the saw by the power cord. Do not disconnect
the plug by pulling on the power cord.
-
-
When changing your position during work switch of the
electric chain saw and actuate the chain brake in order to
prevent an inadvertent start of the chain.
-
Whentransportingtheelectricchainsawoverlongdistances
thepowersupplyplugmustbepulled outandthebarprotec-
tion cover, included in the delivery, must be applied (ꢀ0).
Ensure safe positioning of the electric chain saw during car
transportation to avoid oil leakage.
-
-
-
-
ꢀ0
Store the saw in a secure, dry, lockable room out of reach
of children. It must not be stored outdoors.
For storing the electric chain saw over a long period of time
or shipping it the oil tank must be completely emptied.
Only use approved and marked containers for transporting
and storing chain oil.
Maintenance
-
forperformingmaintenanceworksswitchoftheelectric
chain saw, pull out the power supply plug and secure
it (ꢀ1).
-
Before starting to work, always make sure that the saw is in
safe working order, in particular the chain brake and run-out
brake. Make sure that the saw chain is always sharpened
and tightened correctly (ꢀꢀ).
ꢀ1
-
-
Have the chain brake and run-out brake inspected regularly
(see “Chain brake, run-out brake”).
Regularly check the cable to the power supply for damage
of the covering.
Regularly clean the electric chain saw.
-
-
If the plastic case is damaged, have it immediately repaired
by a skilled person.
-
-
Regularly check the tank cap for tightness.
Do not use the saw if the ON/OFF switch is defective. Have
it repaired by a qualified person.
observetheaccidentpreventioninstructionsissuedby
the competent trade federations and insurance compa-
nies.
Do not perform any modifications on the electric chain
saw. you will endanger your safety.
ꢀꢀ
ꢀ3
ꢀ4
Perform only the maintenance and repair works described
in the instruction manual. All other works must be carried
out by the MAKITA service.
Use only original MAKITA spare parts and accessories.
Applying spare parts which are not original MAKITAparts or
accesories and bar/chain combinations or lengths results in
a high risk of accidents. For accidents and damage resulting
from using sawing devices or accesories which have not
been approved we cannot accept any responsibility.
first aid
For the event of a possible accident, please, make sure
SErVICE
that a first aid box is always immediately available close by.
Immediately replace any items used from the first aid box.
Should you ask for help, please, give the following
information:
- place of accident
- what happened
- number of injured persons
- kind of injuries
- your name.
noTE
Individuals with poor circulation who are exposed to excessive
vibration may experience injury to blood vessels or the nervous
system.
Vibration may cause the following symptoms to occur in the
fingers, hands or wrists: ”Falling asleep” (numbness), tingling,
pain, stabbing sensation, alteration of skin colour or of the skin.
If any of these symptoms occur, see a physician!
8
Technical data
UC3030A
UC3530A / AP
UC4030A / AP
UC4530A
Power consumption
Nominal voltage
Mains frequency
Nominal current
Fuse, electric circuit
Cable length
Watt
V
1570
110 ~
Hz
A
50 - 60
15
A
16
cm
1000
09ꢀ
3/8"
Chain type
Chain pitch
inch
cm
Length of a cut
Max. chain speed
30
35
40
45
m/s
13,3
Sound power level LWA av
per EN 60745-ꢀ-13
dB (A)
101,8
Sound pressure level LpA av
at the workplace per EN 60745-ꢀ-13
dB (A)
90,8
Vibration acceleration
ah,w av per EN 60745-ꢀ-13
- Tubular handle
- Rear handle
Oil pump
m/sꢀ
m/sꢀ
4,7
5,6
automatic
140
Oil tank capacity
ml
Power transmission
Overload protection
Chain brake
direct
electrical
manual or automatic
electrical
Run-out brake
Weight
(without bar/chain)
kg
4,4
Radio interference suppression / EMC
Protective case
Per EMC guidelines EWG 89/336 and EWG 9ꢀ/31
class II (double protective insulation)
Extension cable
(not included)
DIN 57ꢀ8ꢀ/ HO 7RN-F
L= 30 m max., 3x1,5 mmꢀ
1
2
Denomination of components
3
5
4
7
6
11
12 13
9
10
8
1 Tubular handle
2 Hand guard (release for chain brake)
3 Spike bar
4 Sprocket guard quick tightener
5 Sprocket guard, chain brake
6 Carbon brush cover
7 Back hand guard
8 Power cord with plug
9 Guide bar
10 Oil tank cap
17
16
15
14
Figure: Identification plate UC4530A
11 Identification plate
12 Locking button
13 Rear handle
14 Power switch
110V~
13.3m/s
15A
50-60Hz
1570W
Serial number
Year of manufacture
15 Sightglass for oil level
16 Saw chain
17 Cord grip for electric cord (pull relief)
Indicate when ordering spare parts!
9
PUTTInG InTo oPErATIon
CAUTIon: When working on the guide bar or saw chain
always wear protective gloves and pull out the
power supply plug.
CAUTIon: Switch on the electric chain saw only after hav-
ing assembled it completely and inspected!
A
Mounting the guide bar and saw chain
Put the electric chain saw on a stable surface and carry out the
following operations for mounting the bar and chain:
Release chain brake. To do this, pull the hand guard (1) in the
direction of the arrow.
1
Flip up the sprocket guard quick tightener (2) (see also Fig.
G).
4
Push in the sprocket guard quick tightener firmly against spring
pressure, and slowly turn it counter-clockwise until you feel it
engage. Keep pushing in, and turn it as far as possible coun-
ter-clockwise.
2
3
Release the sprocket guard quick tightener (remove pressure)
and now turn it clockwise to its original position. Repeat this
procedure until the sprocket guard (3) is unscrewed.
Pull the sprocket guard (3) up slightly, pull out of the rear fit-
tings (4) and remove.
B
C
D
Position the guide bar (7) and push it against the sprocket
(6).
6
7
Place the saw chain (9) on the sprocket (6). Using your right
hand, guide the saw chain into the upper guide groove (8) of
the guide bar.
The cutting edges of the saw chain on the top of the guide
bar must point in the direction of the arrow!
6
9
8
10
9
10
Using your left hand, lightly press the guide bar against the
holder on the housing and guide the saw chain (9) around the
nose sprocket (10) on the guide bar. While doing this, pull the
saw chain slightly in the direction shown by the arrow.
E
11
Line up the hole in the sprocket guard with the threaded pin
(11).
Turn the chain tensioning screw (H/14) to align the chain ten-
sioning pin (12) with the hole in the guide bar.
12
3
f
First press the sprocket guard (3) into the mounting (13) and
then push it onto the threaded pin (f/11).
13
3
G
Tightening the saw chain
Firmly push in and simultaneously turn the sprocket guard
quick tightener (2, clockwise) in order to screw on the sprocket
guard (3), but do not tighten it yet.
2
Lift the tip of the guide bar slightly and turn the chain tensioner
(14) clockwise until the saw chain engages in the guide groove
on the lower side of the guide bar (see the circle).
Push in the sprocket guard quick tightener (2) again and tight-
en by turning clockwise.
14
2
Release the sprocket guard quick tightener (2) (remove pres-
sure) until it turns freely, then fold it in as shown in the illustra-
tion.
H
11
Checking the chain tension
The chain has the proper tension when it lies against the bottom
edge of the guide bar and can be easily pulled by hand about
ꢀ-4 mm (about 1/8") up from the guide bar.
Check the chain tension frequently - new chains tend to get
longer during use!
When checking the chain tension the motor must be switched
off and the power supply plug pulled out. If the chain is too
loose: Loosen the sprocket guard quick tightener by about a
quarter turn. Tighten the chain as described under “Tightene-
ing the saw chain.”
HInT:
Use ꢀ or 3 saw chains alternately for even wear of the chains,
sprocket and guide bar running surfaces.
In order to guarantee a uniform wear of the groove in the bar the
bar should be turned over whenever replacing the chain.
I
Chain brake
The electric chain saw comes with an inertial chain brake as
standard equipment. If kickback occurs due to contact of the
guide-bartipwithwood(seeSAFETYPRECAUTIONS,page7),
the chain brake will stop the chain through inertia if the kickback
is sufficiently strong.
The chain will stop within a fraction of a second.
run-out brake
The electric chain saw come with a run-out brake as standard
equipment.
The run-out brake ensures that the chain comes to a stop
immediately when the ON/OFF switch is released, thus
preventing the chain from continuing to run and presenting a
hazard.
Testing of the run-out brake is described on page 16.
Chain and run-out brake maintenance
The brake systems are very important safety features, and
like any other part they are subject to a certain amount of
wear. regular inspection and maintenance is important for
your personal safety, and can be properly performed only
by a MAKITA service centre.
SErVICE
J
Engaging the chain brake (braking)
If the kickback is strong enough the sudden acceleration of the
guide bar combined with the inertia of the hand guard (1) will
automatically actuate the chain brake.
3
2
To engage the chain brake manually, simply push the hand
guard (1) forward (towards the tip of the saw) with your left
hand (arrow 2).
1
releasing the chain brake
Pull the hand guard (1) towards you (arrow 3) until you feel it
catch. The brake is now released.
note:
When the chain brake is actuated the power supply to the
motor will be cut off. Testing of the chain brake is described
on page 16.
K
1ꢀ
Saw chain oil
BIOTOP oil is available in the following packing sizes
to suit your individual requirements:
Use a special oil with adhesive addition for lubricating the saw
chain and bar. The adhesive addition prevents that the oil is
centrifuged too fast from the sawing device.
1 liter
order number 980 008 610
order number 980 008 611
5 liters
Do not use mineral oils. In order to protect the invironment the
use of biologically decomposeable oil is prescribed.
Biologically decomposeable oil is stable only for a
limited period of time. It should be consumed within
ꢀ years from the date of manufacture (printed on the
container).
The saw chain oil sold by MAKITA, called BIOTOP, is made
of special vegetable oils and is biologically decomposeable to
100%. BIOTOP has been granted the "blue angel" for being
particularly favourable to the environment (RAL UZ 48).
A
Important note on bio-degradable chain oils
If you are not planning to use the saw again for an ex-
tended period of time, empty the oil tank and put in a
small amount of regular engine oil (SAE 30), and then
run the saw for a time. This is necessary to flush out all
remaining bio-degradable oil from the oil tank, oil-feed
system, chain and guide bar, as many such oils tend to
leave sticky residues over time, which can cause damage
to the oil pump or other parts.
The next time you use the saw, fill the tank with BIOTOP
chain oil again. In case of damage caused by using waste
oil or unappropriate chain oil the product guarantee will
be null and void.
Your salesman will inform you about the use of chain
oil.
nEVEr USE WASTE oIL
Waste oil is very dangerous for the environment.
Waste oil contains high amounts of carcinogenic substances.
The residues in the waste oil result in a high degree of wear
and tear at the oil pump and the sawing device.
Waste oil
Inthecaseofdamagecausedbyusingwasteoilorunappropriate
saw chain oil the product guarantee will be null and void.
Your salesman will inform you about the use of saw chain oil.
AVoID SKIn AnD EyE ConTACTS
Mineral oil products as well as oil degrease the skin. If your
skin repeatedly comes in contact with these substances for a
longer period of time, it will desiccate. Various skin deseases
may result. In addition, allergic reactions are known.
Eyes can be irritated by contact with oil. If oil gets into your eyes,
immediately wash them with clear water. If your eyes are still
irrritated, go to see a doctor.
B
13
Refilling the oil tank
only if the motor is switched off and the power supply plug
is pulled out!
1
-
-
Thoroughly clean the oil tank around the cap to prevent dirt
from entering the tank.
Unscrew the tank cap (1) and fill in chain oil until it is on a
level with the bottom edge of the filler socket.
-
Tightly screw on the tank cap.
-
Thoroughly remove any oil that has overflown.
Important!
Before operating the saw for the first time, the oil feed system
must be completely filled, until the chain oil lubricates the chain
and guide bar.
This procedure can take up to two minutes.
-
The oil level can be controlled in the sight glass (2).
In order to ensure sufficient lubrication of the saw chain there
must always be enough oil in the tank.
2
C
Lubricating the saw chain
only if the motor is switched off and the power supply plug
is pulled out!
Toguaranteeatroublefreeoperationoftheoilpumptheoilguide
groove (3) as well as the oil inlet bore in the guide bar (4) must
be cleaned in regular intervals.
3
4
note:
After the saw has been turned off it is normal for residual chain
oil to drip from the oil feed system, the guide bar and the chain
for a time. This does not constitute a defect!
Place the saw on a suitable surface.
Chain oil filter
Dirt particles that accumulate on the chain oil filter will impede
the flow of chain oil. This will eventually lead to poor lubrication,
and faster wear to the chain and guide bar.
If the chain is no longer getting enough lubrication, the chain
oil filter (6) will need to be cleaned or replaced.
-
Remove the sprocket guard, chain, and guide bar (see
PUTTING INTO OPERATION).
-
-
Carefully clean the area around the oil outlet hole (5).
Installation
Using a small screwdriver, carefully remove the serrated
washer (7) and chain oil filter (6).
-
Cleanthechainoilfilter.Ifitisseverelycontaminated,replace
it.
5
-
Plug in the chain saw and let it run until the chain oil comes
out the oil outlet hole.
6
7
-
-
-
Switch off the saw and unplug the power cord.
Clean the area around the oil outlet hole (5) with a cloth.
Insertthechainoilfilter(6)andserratedwasher(7)asshown
in Installation. When the oil filter cannot be secured with
theserratedwasher, replacetheserratedwasherwithanew
one.
-
Put the guide bar, chain, and sprocket guard back on (see
PUTTING INTO OPERATION).
D
14
Plug in the saw
CArEfUL!
Before connecting the saw to a source of electricity, al-
ways make sure to check that when the on/off switch (1)
has been pressed in and released, it automatically comes
back out to the "off" position. If it does not, do not under
any circumstances connect the saw to a power source -
do not plug it in. Take the saw to a MAKITA service centre
before doing any work with it.
1
2
Clip the extension cord and the saw’s power cord into the cord
grip (2).
4
3
Plug the saw plug (3) into the socket of the extension cable
(4).
A
Switching on the motor
-
-
Plug in the saw (see above).
When switching on the electric chain saw always hold it
with both hands. Take the back handle with the right hand
and the tubular handle with the left hand. Hold the handles
tightly with your thumbs facing your fingers. The bar and
chain must not be in contact with any object.
-
-
First depress the locking button (5) and then the power
switch (1). Then release the locking button (5).
Attention: The chain starts running immediately. Keep
the power switch depressed as long as the motor is to run.
5
1
CAUTIon:
never lock the power switch in the on position.
Switching off the motor
-
Release the power switch (1).
noTE:
When the chain brake is actuated the power supply to the
motor will be cut off.
If the saw does not start when the on/off switch (1) is
actuated, it will be necessary to release the chain brake.
-
Pull the hand guard (6) firmly in the direction of the arrow
until you feel it catch.
Important:
These models are equipped with a starting current limiter.
This electronic component prevents too abrupt starting of the
electric motor.
6
Excess current cutoff: When the electrical current to the saw
exceeds the permissible level, the power supply to the motor
is automatically cut off. This prevents overheating of the motor
and resulting damage. To start the saw up again, release the
ON/OFF switch and press it again.
CAUTIon: Do not use the saw if the current cutoff repeatedly
switches off the saw. Consult a MAKITA service centre.
B
15
Checking the chain brake
Do not work with the chain saw without first checking the
chain brake!
-
Start the motor as described (make sure you have a good
footing, and place the chain saw on the ground in such a
way that the guide bar is free of contact).
1
-
-
Grasp the tubular handle firmly with one hand and hold the
grip with the other.
Switch on the motor and press the hand guard (1) in the
direction of the arrow with the back of your hand until the
chain brake engages. The chain should stop immediately.
Switch the motor off Immediately and release the chain
brake.
-
Important:Ifthesawchaindoesnotstopinstantlywhen
you carry out this test, do not under any circumstances
use the saw! Take the chain saw to a MAKITA service
center.
C
D
E
Testing the run-out brake
Do not work with the saw without first testing the run-out
brake!
-
Start the motor as described (make sure you have a good
footing, and place the chain saw on the ground in such a
way that the guide bar is free of contact).
-
-
Grasp the tubular handle firmly with one hand and hold the
grip with the other.
Switch the motor on and then back off. The chain should
come to a full stop within two second of switching off the
motor.
Important: If the saw chain does not stop within two
secondwhenyoucarryoutthistest, donotusethesaw!
Inspect the carbon brushes (see page 19).
Checking the chain
lubrication
Never saw when a sufficient chain lubrication is not guaranteed.
Otherwise the life of the sawing device will be reduced. Before
starting work check the oil level in the tank and the oil feeding.
Check the fed oil quantity by following the instructions below:
-
-
Start the electric chain saw.
Hold the running chain saw approx. 15 cm above a trunk or
the ground (use an appropriate surface).
If the lubrication is sufficient, you will see a light oiltrace because
oil will be centrifuged from the chain saw. Pay attention to the
direction the wind is blowing and avoid unnecessary exposure
to the oil spray!
16
MAInTEnAnCE
Sharpening the saw chain
When working on the saw chain you must always pull out
the power supply plug and wear protective gloves.
The chain needs sharpening when:
-
the sawdust from sawing humid wood looks like wood
flour.
-
the saw chain penetrates the wood only under great pres-
sure.
-
-
the cutting edge is visibly damaged.
the sawing device is pulled to the left or the right during the
sawing operation. This is caused by uneven sharpening of
the chain or by damage to one side of it.
Important: Sharpen frequently, but without removing
too much metal!
Generally, 2-3 strokes of the file will be enough.
Have the chain resharpened in a service center when you
have sharpened it yourself several times.
Proper sharpening:
CAUTIon:
Use only chains and guide bars designed for this saw (see
the Extract from the spare-parts list)!
0,64 mm
(.0ꢀ5")
0,64 mm
(.0ꢀ5")
-
Allcuttersmustbeofthesamelength(dimensiona). Cutters
with different lengths result in rough running of the chain and
can cause cracks in the chain.
-
Minimum cutter length is 3 mm (0.11"). Do not resharpen the
chain when the minimum cutter length has been reached;
at this point, the chain must be replaced (see the Extract
from the spare-parts list and "Replacing the chain").
-
-
The depth of the cut is determined by the difference in height
between the depth limiter (round nose) and the cutting
edge.
The best results are obtained with a depth-limiter depth of
0.64 mm (.0ꢀ5").
min.
CAUTIon:
3 mm (0.11”)
Excessive depth increases the
risk of kickback!
-
-
All cutters must be sharpened to the same angle, 30°. Dif-
ferent angles result in a roughly, irregularly running chain,
increase wear and tear and cause chain beakage.
The 85° front rake of the cutter results from the cut depth of
the round file. If the proper file is used in the right manner,
the correct front rake will be obtained automatically.
A
17
files and how to work with them
-
Sharpen using a special file holder with a saw chain round
file dia. 4.0 mm. Normal round files are not appropriate for
this work. See "Accessories" for the order number.
-
-
-
The file should cut only when pushed forwards (arrow). Lift
the file when leading it backwards.
First sharpen the shortest cutter. The length of this cutter is
then the standerd for all other cutters of the chain.
Always guide the file as in fig. shown
4/5
-
The file holder makes file guidance easier. It is marked for
the correct 30° sharpening angle (keep the marks parallel
with the chain when filing, see illustration) and limits the cut
depth to the correct 4/5 of the file diameter. See "Acces-
sories" for the order number.
30°
-
After having sharpened the chain, the height of the depth
limiter must be checked by means of a chain gauge. See
"Accessories" for the order number.
1
2
-
Correct even the smallest excess height with a special flat
file (1). See "Accessories" for the order number.
-
Round off the front of the depth limiter (2).
B
Cleaning the guide bar,
lubricating the sprocket nose
CAUTIon: Protective gloves must be worn.
Regularly inspect the bearing surfaces of the guide bar for
damage, and clean them with a suitable tool.
If the saw is used intensively it will be necessary to lubricate the
return sprocket bearings regularly (once a week). To do this, first
thoroughly clean the ꢀ mm hole at the tip of the guide bar, and
then press in a small amount of multi-purpose grease.
Multi-purpose grease and grease guns are available as acces-
sories.
Multi-purpose grease
Grease gun
(order no. 944 360 000)
(order no. 944 350 000)
C
18
replacing the saw chain
CAUTIon:
Use only chains and guide bars
designed for this saw (see the Extract from the spare parts
list)!
Check the sprocket (1) before mounting a new chain.
CAUTIon:
Worn out sprockets (2) may damage the new chain and must
therefore be replaced.
Do not attempt to replace the sprocket yourself. Sprocket re-
placement requires special training and tools and must be done
at a MAKITA service centre.
1
2
SErVICE
D
Inspecting and replacing the carbon brushes
Important:
Inspect the carbon brushes at regular intervals!
A notch on the brush shows the limit of wear.
noTE:
The carbon brush is very delicate, so be careful not to let it
drop. When taking it out, be sure to note the position it was
installed in, since each brush is run in with the rotor.
-
-
-
Use a slotted bit screwdriver to unscrew the cover (1), and
then pull out the brush (2).
Ifthewearlimithasnotyetbeenreached, putthebrushback
in the same position and screw the cover (1) back on.
Run the saw briefly (about a minute) so the brushes can run
in again.
Important: Now test the run-out brake (see page 16). If the
saw chain does not come to a full stop within two second, run
the saw again briefly and repeat the test until the brake func-
tions properly.
noTE: After installing new carbon brushes, run the saw about
5 minutes and then check the run-out brake.
1
2
E
19
Trouble shooting
observation
Cause
Malfunction
System
electric motor does not no power supply,
Chain saw does not work total
function
cable defective
chain brake actuated
Mains fuse blown
Carbon brushes worn down
insufficient performance
Carbon brushes
low pulling power
oil tank empty,
oil guide groove dirty
no chain lubrication
Oil tank, oil pump
no oil on the saw chain
Saw chain does not stop
instantly
Brake band worn down
Chain brake
Brake
Brake
Carbon brushes worn down
Run-out brake
Saw chain continues to
run
Instructions for periodic maintenance
To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed
regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the prescribed
maintenance work can lead to accidents!
The user of the electric chain saw is not allowed to perform maintenance works which are not described in the instruction manual.
All other works must be carried out by a MAKITA service centre.
Page
General work
Electric chain saw
Plastic case
Regularly clean the outside.
Check for cracks and ruptures. In case of damage have it
immediately repaired at a service centre.
Resharpen regularly.
Saw chain
Guide bar
Replace in time.
Turn over after a certain period of time so that the bearing
surfaces are uniformly worn.
Replace in time.
Sprocket
Chain brake
Run-out brake
Have it replaced in time at a service centre.
Have it inspected regularly at a service centre.
Have it inspected regularly at a service centre.
Each time before putting
the saw into operation
Saw chain
Check for damage and sharpness.
Check the chain tension.
Check for damage, and remove burrs if necessary.
Functional check.
Functional check.
Functional check.
Functional check.
In case of damage have it replaced at a service centre
Check for tightness.
17-18
1ꢀ
Guide bar
Chain lubrication
Chain brake
Run-out brake
Power switch
Power supply cable
Oil tank cap
16
16
16
15
.
After each shutdown
Storage
Guide bar
Chain carrier
Clean the oil inlet bore.
Clean, especially the oil guide groove.
14
18
Chain oil tank
Saw chain/guide bar
Empty.
Demount, clean and lubricate slightly.
Clean the guide groove of the guide bar.
14
Electric chain saw
Store safely in a dry place. After a long storage time, have
the electric chain saw checked at a service centre (resi-
dual oil can become resinic and the valve of the oil pump
clogged).
ꢀ0
Service, spare parts and guarantee
Maintenance and repair
The maintenance and repair work of modern electric motors as well as all safety related assemblies require qualified technical train-
ing and the availability of a special workshop equipped with special tools and testing devices.
Any work not described in this Instruction Manual must be performed only by a MAKITA service centre.
The MAKITAservice centres are provided with all the necessary equipment and skilled and experienced personnel to work out correct
customer solutions and to advise you in all matters accordingly.
Repair attempts by third parties or unauthorised persons void all warranty claims.
Spare parts
A reliable and continuous operation as well as the safety of your chain saw is also subject to the quality of the spare parts used. Use
original MAKITA spare parts only, marked:
Only original spare parts and accessories guarantee the highest quality in material, dimensions, functioning and safety.
Original spare parts and accessories can be obtained from your local dealer. He will also have the relative spare part lists to determine
the required spare part numbers, and will be constantly informed about the latest improvements and also about spare part innovations.
Please, take in mind that in the case that foreign spare parts are used instead of the original MAKITA spare parts this will automati-
cally invalidate the MAKITA product guarantee.
Guarantee
MAKITA guarantees the highest quality and will therefore reimburse all costs for mending through replacement of damaged parts as
a result of material or production faults, which occur within the guarantee time after purchase.
Please, note that in some countries particular guarantee conditions may exist. In case of any doubts, please, contact your salesman
who is responsible for the guarantee of the product.
We ask for your understanding that we cannot accept any responsibility for damage caused by:
•
•
•
•
•
•
•
•
•
•
•
•
Disregard of the instruction manual.
Non-performance of the required maintenance and cleaning instructions.
Normal wear and tear.
Obvious overload due to permanent excess of the upper limits of capacity.
Use of guide bars and saw chains which have not been approved.
Use of guide bar and saw chain lengths which have not been approved.
Use of force, improper use, misuse or accidents.
Damage caused by overheating due to dirt obstructing the cool air supply at the motor case.
Use of unsuitable spare parts or parts which are not original MAKITA parts, as far as they have caused the damage.
Use of unsuitable or old oil.
Damage related to conditions arising from lease or rent contracts.
Works on the chain saw by unskilled persons or performance of inappropriate repairs.
Cleaning, servicing and adjustment works are not covered by the guarantee.All repairs covered by the guarantee are to be performed
by a MAKITA service centre.
ꢀ1
Extract from the spare parts list
Use original MAKITA spare parts only. For performance of repairs and for
replacement of other components your MAKITA service centre should be
consulted.
UC3030A, 3530A, 3530AP
UC4030A, 4030AP, 4530A
1
5
3
2
4
6
20
22
23
21
24
ꢀꢀ
Extract from the spare parts list
Use original MAKITA spare parts only. For performance of repairs and for
replacement of other components your MAKITA service centre should be
consulted.
UC3030A, 3530A, 3530AP
UC4030A, 4030AP, 4530A
Pos. MAKITA no. Qty.
Denominatio
1
ꢀ
3
ꢀꢀ6 114 100
ꢀꢀ6 ꢀ13 ꢀ00
970 805 410
1
1
ꢀ
Oil tank cap compl.
Sprocket guard compl.
Carbon brushes
4
4
4
4
44ꢀ 030 661
44ꢀ 035 661
44ꢀ 040 661
44ꢀ 045 661
1
1
1
1
Sprocket nose bar 30 cm (1ꢀ")
Sprocket nose bar 35 cm (14")
Sprocket nose bar 40 cm (16")
Sprocket nose bar 45 cm (18")
4
4
444 035 661
444 040 661
1
1
Sprocket nose bar 35 cm (14"), UC3530AP
Sprocket nose bar 40 cm (16"), UC4030AP
5
5
5
5
5ꢀ8 09ꢀ 646
5ꢀ8 09ꢀ 65ꢀ
5ꢀ8 09ꢀ 656
5ꢀ8 09ꢀ 66ꢀ
1
1
1
1
Saw chain 3/8", 30 cm
Saw chain 3/8", 35 cm
Saw chain 3/8", 40 cm
Saw chain 3/8", 45 cm
6
6
-
95ꢀ 100 633
95ꢀ 100 643
226 211 050
ꢀꢀ6 ꢀ11 040
1
1
1
1
Chain protection cover (30-35 cm)
Chain protection cover (40-45 cm)
Chain oil filter (felt)
-
Lock washer (clamping ring)
Accessories (not included in the delivery inventory)
20 953 100 090
ꢀ1 953 004 010
22 953 003 090
23 953 003 060
24 953 030 010
1
1
1
1
1
Chain gauge 3/8”
File handle
Round file ø 4 mm
Flat file
File holder compl. 3/8”
ꢀ3
To find your local distributor, please visit
Specifications subject to change without notice
Makita Werkzeug GmbH
Postfach 70 04 ꢀ0
D-ꢀꢀ004 Hamburg
Germany
Form: 995 704 437 (8.07 GB)
|