Lg Kstk1 User Manual

nstallation Instructions  
I
The following instructions will help guide you through the initial steps of setting up your dryer for use.  
Please note that every section of this manual provides important information regarding the preparation and use of  
your dryer, and it is important that you review this entire manual before proceeding with any installation or use.  
More detailed instructions concerning electrical connections, gas connections, and exhaust requirements are  
provided in other parts of this manual.  
F
Positioning the Dryer.  
Choose a location with a solid floor for your dryer. Place the dryer at least eighteen inches above the floor for a  
garage installation. After placing the dryer in the desired location, make sure that it has the required clearances  
shown.  
33.5"  
(850 mm)  
25.2"  
(640 mm)  
23.6"  
(600 mm)  
Note  
Leveling legs should be secured.  
All four legs should be on a solid, even floor and properly leveled as shown in this manual.  
If dryer is not level, laundry may not be able to accurately detect the moisture level in the clothes.  
When leveling, please be cautious to avoid injury.  
6
nstallation Instructions  
I
Stacking Kit  
In order to stack this dryer an LG stacking kit is  
required.  
F
WARNING  
• Incorrect installation can cause serious  
accidents.  
• The weight of the dryer and the height of  
installation makes the stacking procedure too  
risky for one person. This procedure should be  
performed by 2 or more experienced service  
personnel.  
Dryer  
• The dryer is not suitable for a built-in installation.  
Please do not install as a built-in.  
• Do not operate the dryer is disassembled.  
Washer  
Support Holder  
3. Assemble the stacking kit as following.  
This dryer may only be stacked on top of an LG  
washer. DO NOT attempt to stack this dryer on any  
other washer, as damage, injury or property damage  
could result.  
To stack this dryer, the support holder included with  
the stacking kit must be used.  
Peel the protective film from the double-sided tape on  
the bracket for your size washer.  
Attaching the support holder.  
Align the stacking kit holes and the rear cover holes  
and then firmly attach the bracket to the side of the  
washer in that position.  
23.6 inch(600 mm)  
Washer Top plate size  
Support  
Holder  
23.6 inch  
(600mm)  
Shape  
4. Assemble a stacking kit as following.  
Installation Procedure  
• Screw 2 screws which were removed earlier to  
assemble dryer and stacking kit.  
1. Place the LG dryer on the LG Washing machine.  
2. Remove two screws at the bottom of the rear cover  
on each side as shown below.  
• Use accessory screws [1.2inch (30mm)] to assemble  
washer rear cover and stacking kit.  
,
• The procedure for the opposite side will be the  
same.  
8
nstallation Instructions  
I
Level the dryer  
F
1. Level the dryer is to prevent undesirable noise  
and vibration.  
Locate your dryer on a solid, level floor. Make  
sure it is not subjected to splashing water or  
freezing temperatures. Do not store flammable  
materials near the dryer.  
2. If the dryer is not properly level, adjust the front  
leveling legs up and down as necessary.  
Turn the legs clockwise to raise the dryer and  
counterclockwise to lower the dryer. Check the  
dryer diagonally to make sure it does not rock  
either way. Readjust the legs if necessary.  
Adjustable feet  
Raise  
Lower  
Adjustable feet  
Adjustable feet  
Diagonal Check  
When pushing down corners of the dryer,  
the machine should not move at all.  
(Check in either direction.)  
If machine rocks when pushing the machine top plate  
diagonally, adjust the feet again.  
9

Sanyo Ecoi C1305dxhn8 User Manual
Samsung Ch18cax User Manual
Roberts Gorden Combat At 154 User Manual
MCCULLOCH MCT2303A User Manual
HITACHI 51F710G User Manual
GE 20 User Manual
CRAFTSMAN 113.177060 User Manual
BLACK DECKER COFFEEMATIC DCM94WH User Manual
BLACK DECKER COFFEEMATIC DCM90M User Manual
ACER ASPIRE 3 A315 23S User Manual