OWNER’S MANUAL
DRYER
Read this owner’s manual thoroughly before operating the appliance
and keep it handy for reference at all times.
DLEX7600*
DLGX7601*
MFL67731070
PRODUCT FEATURES
3
PRODUCT FEATURES
Easy-to-Use Control Panel
An entire selection of user-friendly functions make operating the dryer easy.
Two-way Easy-access Reversing Door
The LG EasyLoadTM can be tilted open from the top, hamper-style, allowing you to easily load the dryer without items falling
on the floor. The door still swings open to provide easy access for unloading or loading of bulkier items. The door hinge can
be reversed to adjust to the installation location.
Steam Functions (Steam models)
LG's steam technology allows you to inject fabrics with a swirling jet of steam to refresh clothes, reduce static, and make
ironing easier. Simply select the Steam FreshTM cycle or Wrinkle Care cycle.
Flow SenseTm Duct Blockage Sensing System Indicator
The Flow SenseTM duct blockage sensing system detects and alerts you to restrictions in the installed household ductwork
that reduce exhaust airflow through the dryer. If you see the alert: Clean or repair the ducts to remove the restrictions. Keep
your ducts free of blockage to help increase efficiency and reduce long drying times caused by blocked ducts.
Smart DiagnosisTm
Should you experience any technical difficulty with your dryer, it has the capability of transmitting data via your telephone
to the Customer Information Center. The call center agent records the data transmitted from your machine and uses it to
analyze the issue, providing a fast and effective diagnosis.
Tag On (on some models)
The Tag On feature works on most smart phones equipped with the NFC function and based on the Android operating
system (OS).
Using the LG Smart Laundry application, the Tag On feature will allow you to diagnose your appliance, download new cycles,
and see the status of your appliance by simply touching the smart phone to the Tag On logo of the appliance.
Protocol P154
Sanitization Performance of
Residential Clothes dryer
4
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or
CAUTION.
These words mean:
You will be killed or seriously injured if you do not immediately follow instructions.
DANgER -
WARNINg - You may be killed or seriously injured if you do not follow instructions.
CAUTION - You may be slightly injured or cause damage to the product if you do not follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what may happen if the instructions are not followed.
WARNINg – Risk of Fire
Install the clothes dryer according to the manufacturer’s instructions and local codes.
Clothes dryer installation must be performed by a qualified installer.
•
•
Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed,
it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.
Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct
clothes dryer airflow and increase the risk of fire.
To reduce the risk of severe injury or death, follow all installation instructions.
Save these instructions.
•
•
WARNINg
For your safety the information in this manual must be followed to minimize the risk of fire or explosion or
to prevent property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
•
•
a. Do not try to light any appliance.
b. Do not touch any electrical switch; do not use any phone in your building.
c. Clear the room, building or area of all occupants.
d. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
e. If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or your gas supplier.
•
SAFETY INSTRUCTIONS
5
ImPORTANT SAFETY INSTRUCTIONS
WARNINg
To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic
precautions, including the following:
Installation
• Remove all protective vinyl film from the product.
Failure to do so may result in product damage, smoke,
or fire.
Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
•
• gas dryers mUST be exhausted to the outside.
Failure to follow these instructions may result in fire or
death.
Do not install or store this appliance where it will be
exposed to the weather.
•
•
The dryer exhaust system must be exhausted to the
outside of the dwelling. If the dryer is not exhausted
outdoors, some fine lint and large amounts of moisture
will be expelled into the laundry area. An accumulation
of lint in any area of the home may create a health and
fire hazard.
•
Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
Properly ground the dryer to conform with all
governing codes and ordinances. Follow the details
in the installation instructions. Electric shock may result
if the dryer is not properly grounded.
•
•
Use only rigid, semi-rigid or flexible metal 4-inch
(10.2 cm) diameter duct inside the dryer cabinet or
for exhausting to the outside. Use of plastic or other
combustible ductwork may cause fire. Punctured
ductwork may cause fire if it collapses or becomes
otherwise restricted in use or during installation.
•
Before use, the dryer must be properly installed as
described in this manual. Electric shock may result if
the dryer is not properly grounded.
Install and store the dryer where it will not be exposed to
temperatures below freezing or exposed to the weather.
•
•
Ductwork is not provided with the dryer, and you
should obtain the necessary ductwork locally. The
end cap should have hinged dampers to prevent
backdraft when the dryer is not in use. Failure to
follow these instructions may result in fire or death.
•
•
All repairs and servicing must be performed by
authorized service personnel unless specifically
recommended in this Owner’s manual. Use only
authorized factory parts. Failure to follow this warning
may result in serious injury, fire, electric shock, or death.
The exhaust duct must be 4-inch (10.2 cm) in
diameter with no obstructions. The exhaust duct
should be kept as short as possible. make sure
to clean any old ducts before installing your new
dryer. Failure to follow these instructions may result in
fire or death.
To reduce the risk of electric shock, do not install
the dryer in humid spaces. Failure to follow this
warning may result in serious injury, fire, electric shock,
or death.
•
•
Rigid, semi-rigid or flexible metal ducting is
recommended for use between the dryer and the
wall. All non-rigid metal transition duct must be
UL-listed. Use of other materials for transition
duct could affect drying time. Failure to follow these
instructions may result in fire or death.
•
•
•
Connect to a properly rated, protected, and sized
power circuit to avoid electrical overload. Improper
power circuits may melt, creating electric shock and/or
fire hazard.
Remove all packing items and dispose of all
shipping materials properly. Failure to do so may
result in burns, fire, explosion, or death.
•
•
•
•
•
Do not use sheet metal screws or other fasteners
which extend into the duct that could catch lint and
reduce the efficiency of the exhaust system. Secure
all joints with duct tape. For complete details, follow
the Installation Instructions. Failure to follow these
instructions may result in fire or death.
Place the dryer at least 18-inch (45.7 cm) above the
floor for a garage installation. Failure to do so may
result in burns, fire, explosion, or death.
Keep all packaging from children. Packaging material
can be dangerous for children. There is a risk of
suffocation.
Certain internal parts are intentionally not
gronunded and may present a risk of electronic
shock only during serving.
Service personnel - do not contact the following
parts while the appliance is energized: CONTROL
BOARD
Do not install near another heat source such as a
stove, oven or heater. Failure to follow this warning
may result in product deformation, smoke, or fire.
Do not place candles, smoking materials, or other
flammables on top of the product. Dripping wax, smoke,
or fire may result.
6
SAFETY INSTRUCTIONS
Operation
Do not fill the steam feeder with gasoline,
dry cleaning solvents, or other flammable or
explosive substances. Failure to follow these
instructions may result in fire or death.
•
Read all instructions before using the appliance.
•
•
Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, or other flammable
or explosive substances, as they give off vapors
that could ignite or explode.
Do not touch the steam nozzle in the drum
during or after the steam cycles. Failure to follow
these instructions may result in a burn hazard.
•
•
Do not fill the steam feeder with hot water (over
86 °F/30 °C). Failure to follow these instructions
may result in a burn hazard.
Do not reach into the appliance if the drum is
moving.
•
•
Do not allow children to play on or in the appliance.
Close supervision of children is necessary when
the appliance is used near children.
maintenance
Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
Do not repair or replace any part of the appliance
or attempt any servicing unless specifically
recommended in the user maintenance instructions
or in published user-repair instructions that you
understand and have the skills to carry out.
•
•
•
Do not use heat to dry articles containing foam
rubber or similarly textured rubber-like materials.
Clean the lint filter before or after each load.
•
•
Do not tamper with controls.
•
•
The interior of the appliance and exhaust duct
should be cleaned periodically by qualified service
personnel.
Always check the inside of the dryer for foreign
objects. Failure to follow these instructions may
result in fire or death.
Before the appliance is removed from service
or discarded, remove the door to the drying
compartment.
•
•
Do not store plastic, paper, or clothing that may
burn or melt on top of the dryer during operation.
Failure to follow these instructions may result in fire
or death.
•
•
Certain internal parts are intentionally not
gronunded and may present a risk of electronic
shock only during serving.
Service personnel - do not contact the following
parts while the appliance is energized: CONTROL
BOARD
Be careful when opening and closing the door.
Fingers and hands can get caught in the door and
cause injury if the door drops forward unexpectedly.
Do not place heavy items on or lean against the
top of the door when it is open.
•
•
•
•
Do not attempt to pull the hamper door open
more than 40 degrees.
The dryer could tip forward, causing injury or
damage.
Do not place items on the top of the dryer.
Steam (steam model):
Do not open the dryer door during steam
cycles. Failure to follow these instructions may
result in a burn hazard.
•
Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted
with gasoline, dry-cleaning solvents, or other
flammable or explosive substances as they give
off vapors that could ignite or explode. Failure to
follow these instructions may result in fire or death.
•
SAVE ThESE INSTRUCTIONS
SAFETY INSTRUCTIONS
7
gROUNDINg INSTRUCTIONS
WARNINg
Improper connection of the equipment-grounding conductor may result in a risk of electric shock.
Check with a qualified electrician or service person if you are in doubt that the appliance is properly
grounded.
This appliance must be grounded. In the event
of malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of least
resistance for electric current.
Do not, under any circumstances, cut or
•
•
•
remove the ground prong from the power cord.
To prevent personal injury or damage to the dryer,
the electrical power cord must be plugged into a
properly grounded outlet.
This appliance must be equipped with a cord
having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
For personal safety, this dryer must be properly
grounded. Failure to do so may result in electric
shock or injury.
•
•
Refer to the installation instructions in this
manual for specific electrical requirements for
your model. Failure to follow these instructions
may create an electric shock hazard and/or a fire
hazard.
Do not modify the plug. If it will not fit the outlet,
have a proper outlet installed by a qualified
electrician.
•
•
This appliance must be connected to a
grounded metal, permanent wiring system or
an equipment-grounding conductor must be
run with the circuit conductors and connected
to the equipment-grounding terminal or lead
on the appliance. Electric shock may result if the
dryer is not properly grounded.
This dryer must be plugged into a properly
grounded outlet. Electrical shock may result if
the dryer is not properly grounded. have the
wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly
grounded. Failure to follow these instructions
may create an electric shock hazard and/or a fire
hazard.
•
The dryer should always be plugged into its
own individual electrical outlet which has a
voltage rating that matches the rating plate. This
provides the best performance and also prevents
overloading house wiring circuits which can cause
a fire hazard from overheated wires.
•
Never unplug your dryer by pulling on the
power cord. Always grip the plug firmly and pull
straight out from the outlet. The power cord may
be damaged, resulting in a risk of fire and electric
shock.
•
•
Repair or replace immediately all power
cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks
or abrasion damage along its length or at either
end. The power cord may melt, creating electric
shock and/or fire hazard.
When installing or moving the dryer, be careful
not to pinch, crush, or damage the power cord.
This will prevent injury and damage to the dryer
from fire and electric shock.
•
8
SAFETY INSTRUCTIONS
CALIFORNIA SAFE DRINKINg WATER AND TOXIC ENFORCE-
mENT ACT
•
This act requires the Governor of California to publish a list of substances known to the state to cause cancer,
birth defects, or other reproductive harm and requires businesses to warn customers of potential exposure to
such substances.
•
Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,
formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.
•
•
Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be
minimized further by properly venting the dryer to the outdoors.
WARNINg
This product contains chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
PRODUCT OVERVIEW
9
PRODUCT OVERVIEW
Parts
Control
Reversible
panel
door
Terminal block
access panel
Power cord
location
(gas models)
(electric models)
Water inlet valve
(on some models)
Gas connection
location
Lint filter
Leveling
(gas models)
feet
Exhaust duct
outlet
Accessories
Two-Way Reversible Door
(on some models)
Included Accessories
Release
Y connector
(steam models) (steam models)
Hoses
Safety Tether Kit
(on some models)
Hamper
door
Optional accessories
Swing door
The LG EasyLoad™ feature allows you to open the
dryer door from the top, hamper-style, when loading the
dryer to help guide clothes into the drum and prevent
them from falling onto the floor. When unloading the
dryer or loading bulkier items, use the swing door for
easy access to the drum.
Drying rack
(sold separately)
No. 3750EL0001C
Side vent kit
(sold separately)
Kit No. 383EEL9001B
Safety Tether Kit
This optional kit helps prevent the dryer tipping if children climb on the door or if someone should fall onto the
door. It is recommended that you install this kit, depending on your situation, but it is not required. Follow the
customer installation instructions included with the kit to properly install the kit. If you do not install the kit, store it
out of reach of children.
NOTE
For your safety and for extended product life, use only authorized components. The manufacturer is not
responsible for product malfunction or accidents caused by the use of separately purchased unauthorized
components or parts.
•
•
The images in this guide may be different from the actual components and accessories, which are subject
to change by the manufacturer without prior notice for product improvement purposes.
10 INSTALLATION
INSTALLATION
Installation Overview
Please read the following installation instructions first after purchasing this product or transporting it to another
location.
Check and choose
the proper location
Level the dryer
Vent the dryer
Connect electric dryers
Test run
Connect the inlet hose
(steam models)
Connect gas dryers
Gas dryer
Electric dryer
Plug in the power cord
Installation test
Product Specifications
The appearance and specifications listed in this manual may vary due to constant product improvements.
Dryer models
Description
DLEX7600*, DLgX7601*
Steam Dryer
Electrical requirements
gas requirements
max. water pressure
Dimensions
Please refer to the rating label regarding detailed information.
NG: 4–10.5-inch WC
LP: 8–13-inch WC
20–120 psi (138–827 kPa)
27” (W) X 28 15/16” (D) X 40 3/16” (H), 50 1/4” (D with door open)
68.6 cm (W) X 73.4 cm (D) X 102 cm (H), 127.5 cm (D with door open)
Gas dryer : 132.52 lb (60.11 Kg)
Net weight
Electric dryer : 129.76 lb (58.86 Kg)
Drying capacity
- Normal cycle
- Steam cycle
IEC 7.3 cu.ft. (22.5 lb/10.2 kg)
IEC 7.3 cu.ft.(8 lbs/3.6kg)
INSTALLATION 11
Installation Location Requirements
WARNINg
Read all installation instructions completely before installing and operating your dryer! It is important that you
review this entire manual before installing and using your dryer. Detailed instructions concerning electrical
connections, gas connections, and exhaust requirements are provided on the following pages.
The installation requires:
A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors. See
Venting the Dryer.
•
•
•
•
A grounded electrical outlet located within 2 ft. (61 cm) of either side of the dryer. See Connecting Electric
Dryers .
A sturdy floor to support the total dryer weight of 200 lb (90.7 kg). The combined weight of a companion
appliance should also be considered.
No other fuel-burning appliance can be installed in the same closet as a dryer.
Do not operate your dryer at temperatures below 45 °F (7 °C). At lower temperatures, the dryer might not shut off
at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored
in an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do
not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local
building inspector.
NOTE
The floor must be level, with a maximum slope of 1 inch (2.5 cm) under the entire dryer.
Clothes may not tumble properly, and automatic sensor cycles may not operate correctly if dryer is not
level.
•
•
For a garage installation, you will need to place the dryer at least 18-inch (46 cm) above the floor. The
standard pedestal is 15-inch (38.1 cm). You will need 18-inch (46 cm) from the garage floor to the bottom
of the dryer.
Clearances
Installation Spacing for Recessed Area or Closet Installation
The following spacing dimensions are recommended for this dryer. This dryer has been tested for clearances of
1 inch (2.5 cm) on the sides and rear. Recommended clearances should be considered for the following reasons:
Additional clearances should be considered for ease of installation and servicing.
Additional clearances might be required for wall, door and floor moldings.
•
•
•
Additional clearances should be considered on all sides of the dryer to reduce noise transfer.
For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are
required. Louvered doors with equivalent ventilation openings are acceptable.
Companion appliance spacing should also be considered.
•
12 INSTALLATION
Closet Ventilation Requirements
Closets with doors must have both an upper and lower vent to prevent heat and moisture buildup in the closet.
One upper vent opening with a minimum opening of 48 sq. in. (310 cm2) must be installed no lower than 6 feet
above the floor. One lower vent opening with a minimum opening of 24 sq. in. (155 cm2) must be installed no
more than one foot above the floor. Install vent grills in the door or cut down the door at the top and bottom to
form openings. Louvered doors with equivalent ventilation openings are also acceptable.
NOTE
There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of
vibration from one appliance to another. If there is enough vibration, it could cause appliances to make noise
or come into contact, causing paint damage and further increasing noise.
Installation Spacing for Recessed Area or Closet
3"
(7.6 cm)
14" max.*
(35.6 cm)
21 1/4"
18" min.
(54 cm)
48 in.2
(45.7 cm)
(310 cm2)
24 in.2
(155 cm2)
5"**
(12.7 cm)
28 15
(73.4 cm)
/
"
16
Closet Door Vent
Requirements
50 1/4"
(127.5 cm)
3"
1"
27"
(68.6 cm)
1"
(7.6 cm)
(2.5 cm)
(2.5 cm)
* Required spacing
** For side or bottom venting, 2-inch (5.1 cm) of spacing is allowed
Installation Spacing for Cabinet
For cabinet installation with a door, minimum ventilation openings in the top of the cabinet are required.
* Required spacing
7" (17.8 cm)
7" (17.8 cm)
*
*
5"
28 15
(73.4 cm)
/
"
1"
*
16
1"
27"
(68.6 cm)
1"
*
(12.7 cm)
(2.5 cm)
(2.5 cm)
(2.5 cm)
INSTALLATION 13
Use an adjustable wrench to turn the leveling
feet. Unscrew the legs to raise the dryer or
screw in the legs to lower it. Raise or lower with
the leveling feet until the dryer is level from side
to side and front to back. Make sure that all four
leveling feet are in firm contact with the floor.
Leveling the Dryer
2
WARNINg
To reduce the risk of injury to persons, adhere
to all industry recommended safety procedures
including the use of long-sleeved gloves and
safety glasses. Failure to follow this warning may
result in serious injury or death.
The appliance is heavy. Two or more people
are required when installing the dryer. Failure to
follow this warning may result in serious injury
or death.
•
To ensure that the dryer provides optimal drying
performance, it must be level. To minimize
vibration, noise, and unwanted movement, the
floor must be a perfectly level, solid surface.
•
NOTE
Reversing the Door
Adjust the leveling feet only as far as necessary
to level the dryer. Extending the leveling feet more
than necessary may cause the dryer to vibrate.
Before you Begin
NOTE
Service calls to reverse the door are not
covered under the product warranty.
Position the dryer in the final location. Place a
level across the top of the dryer.
1
The door reversal process for the two-way door
is more complex than for a conventional dryer
door. Read through these instructions in their
entirety before beginning the process, in order
to gauge whether to have the procedure done
by a professional installer or service person.
•
Level
lg.com/us/support/videos/video-tutorials-view,
How to Reverse the Door – LG EasyLoad™
Dryer.
•
Leveling Feet
All four leveling feet must rest solidly on the
floor. Gently push on the top corners of the
dryer to make sure that the dryer does not
rock from corner to corner.
•
Tools Required
Phillips screwdriver
•
•
Large flat blade screwdriver (recommended
for hinge screws if they are tight or your Phillips
screwdriver is worn)
If you are installing the dryer on the optional pedestal,
you must use the leveling feet on the pedestal to
level the dryer. The dryer leveling feet should be fully
retracted.
Small flat blade screwdriver (for lifting out parts)
•
WARNINg
THE DRYER DOOR IS VERY LARGE AND
HEAVY. Failure to follow the instructions below
may result in damage to the dryer, property
damage or personal injury.
To avoid damage to the dryer or the door,
support the door with a stool or box that fits
under the door, or have an assistant support
the weight of the door.
•
Avoid dropping the door to avoid damage to the
door or the floor.
•
•
Unplug the dryer or turn off power at the main
circuit breaker before beginning door reversal.
14 INSTALLATION
Door Reversal Instructions
c. Remove the hinge cover by gently prying it up
with a flat blade screwdriver, being careful not
to scratch the paint. Rotate the hinge cover
180 degrees and install it on the opposite side,
where the hinge was attached.
NOTE
The instructions here are for changing the door
swing from a right to a left side hinge. If the
door has been reversed, and it is necessary to
change it back, use care when following these
instructions. Some of the illustrations and the left/
right references will be reversed, and you will
need to read the instructions carefully.
With the door on a protected surface, remove
the 16 screws on each side of the door and
lift off the inner door frame using a flat blade
screwdriver. Remove the latch hook and blank
and install them on the opposite side.
4
5
Inner door
frame
Blank Latch hook
WARNINg
Be sure to support the weight of the door before
removing the hinge screws.
Swing door
Remove the 4 screws securing the hinges to
the door frame. Remove the two plastic cover
caps. Reinstall the hinges and cover caps on the
opposite sides from which they were removed.
Open the door from the side so that the hinge
screws are accessible.
1
Remove the four hinge screws.
2
While supporting the door, remove the four hinge
screws, two from each hinge. Set the door aside
face down on a protected surface to prevent
damage to the door or the work surface.
Hinge
assembly
Cover cap
With the hinges and cover caps in the new
locations, remount the inner door frame onto the
outer door frame with the screws removed in
step 4 above.
6
Reverse the components on the cabinet.
3
hinge
hinge
cover
latch
hole
cover
latch
mechanism
WARNINg
Be sure to support the weight of the door before
hinge
cover
hinge
installing the hinge screws.
a.Use a Phillips screwdriver to remove the two
screws and the latch mechanism on the front
panel of the cabinet.
b.Remove the latch hole cover by gently prying it
up with a flat blade screwdriver, being careful
not to scratch the paint. Install the latch hole
cover on the opposite side, where the latch
mechanism was removed. Install the latch
mechanism in the position from which you
removed the latch hole cover, using the two
screws removed in step a.
INSTALLATION 15
Reverse the components on the cabinet.
Reinstall the door.
7
3
While supporting the door, install the four hinge
screws removed in step 2. Test the swing of
the door to make sure the hinges and latch are
properly aligned and that the door opens, closes
and latches properly in both directions.
Hinge
cover
Upper
hinge
latch
mechanism
Latch
hole
cover
Hinge
bracket
Hinge
a.Use a Phillips screwdriver to remove the two
screws and the latch mechanism on the front
panel of the cabinet.
Swing Door
b.Remove the latch hole cover by gently prying it
up with a flat blade screwdriver, being careful
not to scratch the paint. Install the latch hole
cover on the opposite side, where the latch
mechanism was removed. Install the latch
mechanism in the position from which you
removed the latch hole cover, using the two
screws removed in step a.
Easy load door (on some models)
WARNINg
Be sure to support the weight of the door before
c. Remove the hinge cover by gently prying it up
with a flat blade screwdriver, being careful not
to scratch the paint. Rotate the hinge cover
180 degrees and install it on the opposite side,
where the upper hinge was attached.
installing the hinge screws.
ON THE CABINET :
Open the door from the side so that the hinge
screws are accessible.
1
d.Reverse the hinge and the hinge bracket at
the bottom of the cabinet. Remove the two
screws from the hinge bracket at the bottom
right and remove the hinge bracket. Remove
the lower of the two screws behind the hinge
bracket. Do NOT remove the upper screw
behind the hinge bracket. Set the parts aside.
Two large
screws
Two small
screws
CAUTION
Do NOT remove any of the eight screws on the
face of the cabinet (marked below). Doing so
could result in damage to the dryer and the need
for a service call to repair the dryer.
Remove the four hinge screws
2
While supporting the door, remove the four hinge
screws, two from each hinge. Set the door aside
face down on a protected surface to prevent
damage to the door or the work surface.
16 INSTALLATION
e.Remove the three screws on the hinge at the
bottom left. Remove the hinge and reinstall it
on the right side. The top screw will occupy
the hole where you removed the screw behind
the hinge bracket in step d.
Switch the door strike and the blank cover.
Remove the two screws on the door cover that
secure the door strike.
5
Switch the door strike and the blank cover,
installing them on the opposite sides from which
they were removed.
f. Install the hinge bracket removed in step d on
the bottom left side, first installing one screw
behind the hinge bracket.
Short
screws
Long
screw
Cabinet Reversal complete
hinge
cover
Blank cover
Door strike
Raise
Pull
latch
mechanism
latch hole
cover
hinge
hinge
bracket
ON THE DOOR:
Lift off the door cover.
Remove blank cover
4
With the door laid inside facing up on a protected
surface, remove the twelve screws on the inside
of the door. Carefully lift off the door cover with
the help of a small flat blade screwdriver inserted
in the upper corner (circled below).
Gently pry out the hole plug on the side of
the door cover and install it in the hole on the
opposite side.
WARNINg
The edges of the door cover may be sharp. Take
care when handling, or wear gloves to avoid
injury.
Hole
plug
Twelve screws
Set the door cover aside.
Hole
plug
Side
Interlock
button
INSTALLATION 17
Reverse the components inside the door.
6
You will now be removing and reversing various components inside the door. See below for a detailed
diagram and identification of the inner structure and parts of the door. (The diagram shows the “before view”
of the door, with the default set-up for a right side hinge swing. After following these instructions, your door
should be a mirror image of the illustration.)
Top interlock buttons
Inner lock rods
Upper
hinge
assembly
Upper
hinge filter
Upper
hinge
pivot
Top lock rod
Side lock rod
Glass
Side Interlock button
Lower
hinge
assembly
Lower
hinge filler
Lower
hinge
bracket
Bumpers
Interlock buttons
Low hinge filler
Side lock rod
Top lock rod
Inner lock rods
Lower hinge bracket
Upper hinge pivot
Hole plug
Lower hinge assembly
Upper hinge assembly
Upper hinge filler
18 INSTALLATION
Lift out the gray interlock button in the side
of the door.
Remove the upper hinge pivot.
7
10
Once the top lock rod has been removed, the
hinge pivot can easily be removed from the
hinge assembly on the upper left and set aside.
Make sure to remove the spring with the
interlock button and to keep the two together.
Set the interlock button aside. Do not confuse
these with the interlock buttons from the top of
the outer door.
Upper hinge
assembly
Upper
hinge
pivot
Remove the side lock rod.
8
Remove the side lock rod from the lower hinge
bracket by lifting the top end of the rod and
sliding it toward the top of the door. The spring
should remain attached to the lock rod. Set the
lock rod aside.
Reverse the upper hinge assembly and
hinge filler.
11
Lift out the upper hinge filler (on the right) and
set it aside.
Carefully lift the upper hinge assembly (on the
left) out of the outer door frame, using a small
flat blade screwdriver if necessary. Rotate
the hinge assembly 180 degrees and install it
on the upper right side of the outer door. You
will need to press firmly to install the hinge
assembly.
Spring
The hinge pivot removed in step 11 will be
installed later.
Remove the top lock rod.
9
Upper hinge assembly
Upper hinge pivot
Now rotate the hinge filler 180 degrees and
install it on the upper left side of the door.
a.Slide the lock rod to the right to remove it from
the hinge assembly on the left side.
b.While sliding the lock rod right, lift the right end
up and out of the guides.
Upper hinge filler
NOTE
Do not remove the two inner lock rods and
two interlock buttons (see page 17) located
underneath the top lock rod. They do NOT need
to be reversed.
INSTALLATION 19
c. Flip over the lower hinge bracket and
release the tabs on the back locking the
hinge filler to the hinge bracket.
Reinstall the top lock rod.
12
Rotate the top lock rod (removed in step 10)
180 degrees end for end from its original
position and reinstall it. The spring should now
be to the right of center, with the spring on the
side of the rod facing the top of the door.
a.Insert the right end of the lock rod into the
right hinge assembly. Make sure the rod is
aligned with the guides in the door panel.
Tab
d.Rotate the hinge 180 degrees and snap
it back onto the front of the hinge bracket
facing in the opposite direction.
b.Lower the rod into position, sliding it to
bypass the center handle, making sure to
align the lock rod with the guides all the
way across the door panel. When released,
the lock rod should slide completely into
the hinge assembly on the right. Slide the
lock rod back and forth to make sure it is
correctly positioned in the guides and slides
easily.
e.Mount the lower hinge bracket and the filler
on the left side of the door with the screw
removed in step a.
Screw
Install the side lock rod.
14
Flip the side lock rod over and install it on the
opposite side. Insert the lower end into the left
hinge and lower the rod into the guides on the
door while compressing the spring inside the
recess.
Reverse the lower hinge bracket and hinge
assembly.
13
a.Remove the screw from the lower hinge
bracket (on the right) and lift the hinge
bracket out. Set it aside. Remove the two
screws from the lower hinge assembly on
the bottom left and lift the hinge assembly
out.
Make sure the top of the side lock rod is
beside the top lock rod and the two do not
overlap each other, so the two rods can
interact correctly. If they are not aligned
properly, the door will not operate properly.
b.Rotate the lower hinge assembly 180
degrees and install it on the right side using
the two screws removed in step a.
Screws
Lower hinge assembly
20 INSTALLATION
Reinstall the side interlock button.
Now, pick up the upper hinge pivot
removed earlier and rotate it 180 degrees.
Install the hinge on the top left side of the
cabinet.
15
17
Reinstall the side interlock button removed in
step 7. Center the spring in the compartment
and insert the interlock button on top of it.
Reinstall the door cover.
Clean the glass on the door and door cover, if
necessary.
16
Make sure the three gray interlock buttons
are properly installed and that the top and
side lock rods are properly aligned where
they meet. Carefully lower the door cover into
place, aligning the holes in the cover with
the interlock buttons on the top and side and
the bumpers on the bottom. Take care not to
dislodge the lock rods while mounting the door
cover. Once the door cover is in place, secure
it with the 12 screws removed in step 4. The
ten similar screws go around the top and sides
of the door cover. Make sure to install the two
different screws on the bottom edge, in the
locations marked below.
Reinstall the door.
18
Press in the side interlock button on the left
side and hold it down while you press the
hinge pivot into the hinge assembly on the top
right side. If the door has been reassembled
correctly, the lock rod will slide back easily and
lock the pivot in place. The door is now ready
to remount on the opposite side of the dryer.
Two
large
screws
Two
small
screws
Interlock
buttons
Side
interlock
button
While supporting the door, install the two small
hinge screws removed in step 2. Test the
swing of the door to make sure the hinges and
latch are properly aligned and that the door
opens, closes and latches properly in both
directions.
Bumpers
If the door doesn’t operate smoothly, remove
the door and then the door cover to check
that the lock rods and interlock buttons are
properly mounted and aligned.
The interlock buttons should be oriented
correctly and operating smoothly. The interlock
rods should be in the proper position and
should not overlap at the contact point. (See
steps 15-17.)
If the door is damaged, or if the door does not
work after reassembly, contact the call center
at 1-800-243-0000.
INSTALLATION 21
Preassemble a 4-inch (10.2 cm) elbow to the
next 4-inch (10.2 cm) duct section, and secure
all joints with duct tape. Be sure that the male
end of the elbow faces AWAY from the dryer.
Insert the elbow/duct assembly through the
side opening and press it onto the adapter duct.
Secure it in place with duct tape. Be sure that
the male end of the duct protrudes 1½-inch (3.8
cm) to connect the remaining ductwork. Attach
the cover plate to the back of the dryer with the
included screw.
Installing the Side Vent Kit
3
WARNINg
Use a heavy metal vent.
•
•
•
•
Do not use plastic or thin foil ducts.
Clean old ducts before installing this dryer.
To reduce the risk of injury to persons, adhere
to all industry recommended safety procedures
including the use of long-sleeved gloves and
safety glasses.
Failure to follow all of the safety warnings in this
manual could result in property damage, injury
to persons, or death.
•
Cover
Plate
Your new dryer is shipped to vent to the rear. It can
also be configured to vent to the bottom or side (right-
side venting is not available on gas models).
Elbow
1
"
½
(3.8 cm)
An adapter kit, part number 383EEL9001B, may be
purchased from your LG retailer. This kit contains the
necessary duct components to change the dryer vent
location.
Option 2: Bottom Venting
Press the adapter duct onto the blower housing
and secure it to the base of the dryer as shown.
2
Remove the rear exhaust duct retaining screw.
1
Adapter
Duct
Pull out the exhaust duct.
Retaining Screw
Bracket
Rear Exhaust
Duct
Insert the 4-inch (10.2 cm) elbow through the
3
rear opening and press it onto the adapter duct.
Be sure that the male end of the elbow faces
down through the hole in the bottom of the
dryer. Secure it in place with duct tape. Attach
the cover plate to the back of the dryer with the
included screw.
Option 1: Side Venting
Press the tabs on the knockout and carefully
2
remove the knockout for the desired vent
opening (right-side venting is not available on
gas models). Press the adapter duct onto the
blower housing and secure to the base of the
dryer as shown.
Adapter
Duct
Cover
Plate
Elbow
Bracket
Knockout
22 INSTALLATION
Venting the Dryer
WARNINg
To reduce the risk of fire or explosion, electric
shock, property damage, injury to persons or
death when using this appliance, follow basic
safety precautions, including the following:
DO NOT use sheet metal screws or other
fasteners which extend into the duct that
could catch lint and reduce the efficiency of
the exhaust system. Secure all joints with duct
tape. Failure to follow these instructions may result
in fire or death.
•
Do not exceed the recommended duct length
limitations noted in the chart. Failure to follow
these instructions may result in extended drying
times, fire or death.
•
•
Do not crush or collapse ductwork. Failure to
follow these instructions may result in fire or death.
•
•
Ductwork is not provided with the dryer. You
should obtain the necessary ductwork locally.
The vent hood should have hinged dampers to
prevent backdraft when the dryer is not in use.
Failure to follow these instructions may result in fire
or death.
Do not allow ductwork to rest on or contact
sharp objects. Failure to follow these instructions
may result in fire or death.
If connecting to existing ductwork, make sure it
is suitable and clean before installing the dryer.
Failure to follow these instructions may result in fire
or death.
•
The total length of flexible metal duct must not
exceed 8 ft. (2.4 m).
•
•
In Canada, only those foil-type flexible ducts,
if any, specifically identified for use with the
appliance by the manufacturer should be used.
In the United States, only those foil-type flexible
ducts, if any, specifically identified for use with the
appliance by the manufacturer and that comply
with the Outline for Clothes Dryer Transition Duct,
Subject 2158A, should be used.
Venting must conform to local building codes.
Failure to follow these instructions may result in fire
or death.
•
•
•
gas dryers mUST exhaust to the outdoors.
Failure to follow these instructions may result in fire
or death.
Use only 4-inch (10.2 cm) rigid, semi-rigid or
flexible metal ductwork inside the dryer cabinet
and for venting outside. Failure to follow these
instructions may result in fire or death.
Ductwork
Wall Cap Type
Recommended
To reduce the risk of fire, combustion, or
accumulation of combustible gases, DO
NOT exhaust dryer air into an enclosed and
unventilated area, such as an attic, wall, ceiling,
crawl space, chimney, gas vent, or concealed
space of a building. Failure to follow these
instructions may result in fire or death.
•
maximum length
of 4-inch (10.2 cm)
diameter rigid metal
duct
Number
of 90°
Elbows
0
1
2
65 ft.(19.8 m)
55 ft.(16.8 m)
47 ft.(14.3 m)
4"
To reduce the risk of fire, DO NOT exhaust the
dryer with plastic or thin foil ducting. Failure to
follow these instructions may result in fire or death.
•
•
(10.2 cm)
3
4
0
1
2
3
4
36 ft.(11.0 m)
28 ft.(8.5 m)
55 ft.(16.8 m)
47 ft.(14.3 m)
41 ft.(12.5 m)
30 ft.(9.1 m)
22 ft.(6.7 m)
4"
The exhaust duct must be 4-inch (10.2 cm) in
diameter with no obstructions. The exhaust
duct should be kept as short as possible. make
sure to clean any old ducts before installing
your new dryer. Failure to follow these instructions
may result in fire or death.
(10.2 cm)
Use only for
short run
installations
Rigid, semi-rigid or flexible metal ducting is
recommended for use between the dryer and
the wall. All non-rigid metal transition duct
must be UL-listed. Use of other materials for
transition duct could affect drying time. Failure
to follow these instructions may result in fire or
death.
•
21/2"
(6.35 cm)
NOTE
Deduct 6 ft. (1.8 m) for each additional elbow. Do
not use more than four 90° elbows.
INSTALLATION 23
Routing And Connecting Ductwork
NOTE
Follow the guidelines below to maximize drying
performance and reduce lint buildup and
condensation in the ductwork. Ductwork and
fittings are NOT included and must be purchased
separately.
Use 4-inch (10.2 cm) diameter rigid, semi-rigid
or flexible metal ductwork.
•
The exhaust duct run should be as short as
possible.
•
Use as few elbow joints as possible.
•
•
The male end of each section of exhaust duct
must point away from the dryer.
Use duct tape on all duct joints.
•
•
Insulate ductwork that runs through unheated
areas in order to reduce condensation and lint
buildup on duct surfaces.
Incorrect or inadequate exhaust systems
are not covered by the dryer warranty. Dryer
failures or service required because of such
exhaust systems will not be covered by the
dryer warranty.
•
Correct Venting
Incorrect Venting
24 INSTALLATION
d. Connect the long dryer hose to one side of the
Y-connector and connect the washer hose to the
other side.
Connecting the Inlet hose
(Steam models)
The dryer must be connected to the cold water tap
using a new water supply hose. Do not use old hoses.
WIThOUT WAShER: If the dryer does not share
the cold water tap with a washer.
NOTE
a. Connect the straight end of the long hose to the
cold water faucet.
Water supply pressure must be between 20
and 120 psi (138—827 kPa) .
•
•
•
NOTE
Do not strip or cross-thread when connecting
the inlet hose to the valve.
Before connecting the water line to the dryer,
flush several gallons of water into a drain or
bucket. This will help prevent foreign particles
such as sand and scale from clogging the dryer
inlet valve.
•
If the water supply pressure is more than 800
kPa, a pressure-reducing valve should be
installed.
Periodically check the condition of the hose and
replace the hose if necessary.
•
•
•
Do not overtighten. Damage to the coupling
may result.
•
Replace inlet hoses after 5 years of use to
reduce the risk of hose failure.
Connect the hose to the dryer. Connect the
water supply hose to the dryer inlet valve tightly
by hand and then tighten another 2/3 turn with
pliers.
3
Record hose installation or replacement dates
on the hoses for future reference.
Check the rubber seal at each end of the inlet
hoses. Two rubber seals are supplied with each
inlet hose. They are used for preventing water
leaks. Make sure the connection to the cold
water tap is tight.
Make sure that there are no kinks in the hoses
and that they are not crushed.
1
Hose
connector
Rubber
seal
Y connector
Turn on the cold water faucet.
4
5
Check the installation type.
2
Long
hose
Short
hose
Y connector
Check for leaks at the Y-connector (if used) and
in all hoses.
WITH WASHER
WITHOUT WASHER
Connect all water supply hoses tightly by hand
and then tighten another 2/3 turn with pliers.
WITh WAShER: When connecting the dryer to the
same faucet as a washer.
a. Shut off the cold water tap and remove the washer
hose.
NOTE
If any leaks are found, shut off the water faucet,
remove the hose and check the condition of the
rubber seal.
•
b. Connect the short hose to the Y-connector using
one of the rubber seals.
c. Connect the other end of the short hose to the cold
water faucet.
INSTALLATION 25
DO NOT use an open flame to inspect for gas
leaks. Use a noncorrosive leak detection fluid.
Failure to do so may result in fire, explosion, or
death.
•
•
Connecting gas Dryers
WARNINg
To reduce the risk of fire or explosion, electric
shock, property damage, injury to persons, or
death when using this appliance, follow basic
safety precautions.
Use only a new AgA- or CSA-certified gas
supply line with flexible stainless steel
connectors. Failure to do so may result in fire,
explosion, or death.
Securely tighten all gas connections. Failure to
do so may result in fire, explosion, or death.
•
•
gas Supply Requirements
Use Teflon tape or a pipe-joint compound
that is insoluble in propane (LP) gas on all
pipe threads. Failure to do so may result in fire,
explosion, or death.
As shipped from the factory, this dryer is
configured for use with natural gas (Ng). It can
be converted for use with propane (LP) gas.
gas pressure must not exceed 8-inch (20.3 cm)
water column for Ng, or 13-inch (33 cm) water
column for LP.
•
DO NOT attempt any disassembly of the dryer;
disassembly requires the attention and tools of
an authorized and qualified service technician
or company. Failure to follow this warning may
result in fire, explosion, or death.
•
A qualified service or gas company technician
must connect the dryer to the gas service.
Failure to follow these instructions may result
in fire, explosion, or death.
•
•
Electrical Requirements for gas
models Only
Isolate the dryer from the gas supply system
by closing its individual manual shutoff valve
during any pressure testing of the gas supply.
Failure to do so may result in fire, explosion, or
death.
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
Failure to follow this warning may result in fire,
explosion, or death.
•
Supply line requirements: Your laundry room
must have a rigid gas supply line to your dryer.
In the United States, an individual manual
shutoff valve mUST be installed within at least
6 ft. (1.8 m) of the dryer, in accordance with
the National Fuel gas Code ANSI Z223.1 or
Canadian gas installation code CSA B149.1.
A 1/8-inch (0.3 cm) NPT pipe plug must be
installed. Failure to do so may result in fire,
explosion, or death.
•
For personal safety, this dryer must be properly
grounded. Failure to follow this warning may result
in fire, explosion, or death.
•
•
The power cord of this dryer is equipped with
a 3-prong (grounding) plug which mates only
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock
hazard from this appliance. Failure to follow this
warning may result in fire, explosion, or death.
If using a rigid pipe, the rigid pipe should be ½
inch IPS. If acceptable under local codes and
ordinances and when acceptable to your gas
supplier, 3/8-inch (1 cm) approved tubing may
be used where lengths are less than 20 ft. (6.1
m). Larger tubing should be used for lengths
in excess of 20 ft. (6.1 m). Failure to do so may
result in fire, explosion, or death.
•
This dryer must be plugged into a 120-VAC, 60-
hz. grounded outlet protected by a 15-ampere
fuse or circuit breaker. Failure to follow this
warning may result in fire, explosion, or death.
•
•
Where a standard 2-prong wall outlet is
encountered, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet. Failure to
follow this warning may result in fire, explosion, or
death.
Connect the dryer to the type of gas shown on
the nameplate. Failure to do so may result in fire,
explosion, or death.
•
•
To prevent contamination of the gas valve,
purge the gas supply of air and sediment before
connecting the gas supply to the dryer. Before
tightening the connection between the gas
supply and the dryer, purge remaining air until
the odor of gas is detected. Failure to do so may
result in fire, explosion, or death.
Plug dryer into a 120 VAC,
60 hz grounded 3-prong
outlet.
26 INSTALLATION
Connecting the gas Supply
Securely tighten all connections between the
dryer and your laundry room’s gas supply.
4
Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier. Failure to do so may result in fire,
explosion, or death.
•
Turn on your laundry room’s gas supply.
5
6
Check all pipe connections (both internal and
external) for gas leaks with a noncorrosive leak-
detection fluid.
Use only a new stainless steel flexible
connector and a new AgA-certified connector.
Failure to do so may result in fire, explosion, or
death.
•
Proceed to Venting the Dryer.
7
A gas shutoff valve must be installed within 6 ft.
(1.8 m) of the dryer. Failure to do so may result in
fire, explosion, or death.
•
•
The dryer is configured for natural gas when
shipped from the factory. make sure that the
dryer is equipped with the correct burner nozzle
for the type of gas being used (natural gas or
propane gas). Failure to do so may result in fire,
explosion, or death.
3/8"
NPT gas
Connection
1/8" NPT Pipe Plug
Gas Supply Shutoff
Valve
AGA/CSA-Certified
Stainless Steel
Flexible Connector
If necessary, the correct nozzle (for the LP
nozzle kit, order part number 383EEL3002D)
should be installed by a qualified technician
and the change should be noted on the dryer.
Failure to do so may result in fire, explosion, or
death.
•
high-altitude Installations
The BTU rating of this dryer is AGA-certified for
elevations below 10,000 feet.
All connections must be in accordance with
local codes and regulations. Failure to do so may
result in fire, explosion, or death.
•
•
If your gas dryer is being installed at an elevation
above 10,000 feet, it must be derated by a qualified
technician or gas supplier.
gas dryers mUST exhaust to the outdoors.
Failure to do so may result in fire, explosion, or
death.
NOTE
This dryer is configured from the factory for
natural gas (NG). If the dryer is to be used with
propane (LP) gas, it must be converted by a
qualified service technician.
Make sure that the gas supply to the laundry
1
room is turned OFF and the dryer is unplugged.
Confirm that the type of gas available in your
laundry room is appropriate for the dryer.
Remove the shipping cap from the gas fitting at
the back of the dryer. Be careful not to damage
the threads of the gas connector when removing
the shipping cap.
2
Connect the dryer to your laundry room’s gas
supply using a new flexible stainless steel
connector with a 3/8-inch NPT fitting.
3
NOTE
DO NOT use old connectors.
INSTALLATION 27
Special Electrical Requirements for
mobile or manufactured homes
Connecting Electric Dryers
Electrical Requirements for Electric
models Only
Any installation in a manufactured or mobile
home must comply with the Manufactured Home
Construction and Safety Standards Title 24 CFR,
Part 3280 or Standard CAN/ CSA Z240 MH and
local codes and ordinances. If you are uncertain
whether your proposed installation will comply with
these standards, please contact a service and
installation professional for assistance.
•
WARNINg
To help prevent fire, electric shock, serious injury,
or death, the wiring and grounding must conform
to the latest edition of the National Electrical
Code, ANSI/NFPA 70 and all applicable local
regulations. Please contact a qualified electrician
to check your home’s wiring and fuses to ensure
that your home has adequate electrical power to
operate the dryer.
A 4-wire connection is required for all mobile
and manufactured home installations, as well
as all new construction after January 1, 1996.
Failure to do so may result in fire, explosion, or
death.
•
This dryer must be connected to a grounded
metal, permanent wiring system, or an
equipment-grounding conductor must be run
with the circuit conductors and connected
to the equipment-grounding terminal or lead
on the dryer. Failure to do so may result in fire,
explosion, or death.
•
•
A gas dryer must be permanently attached to the
floor.
•
•
The electrical connection for an electric dryer must
be a 4-wire connection. More detailed information
concerning the electrical connection is provided in
the section Connecting Electric Dryers.
The dryer has its own terminal block that must
be connected to a separate 240 VAC, 60-hertz,
single-phase circuit, fused at 30 amperes (the
circuit must be fused on both sides of the
line). ELECTRICAL SERVICE FOR ThE DRYER
ShOULD BE OF ThE mAXImUm RATE VOLTAgE
LISTED ON ThE NAmEPLATE. DO NOT
To reduce the risk of combustion and fire, the dryer
must be vented to the outside.
•
•
•
•
DO NOT vent the dryer under a manufactured
home or mobile home.
Electric dryers may be vented to the outside using
the back, left, right, or bottom panel.
CONNECT ThE DRYER TO 110-, 115-, OR 120-
VOLT CIRCUIT. Failure to follow these instructions
may result in fire, explosion, or death.
Gas dryers may be vented to the outside using the
back, left, or bottom panel. Gas dryers may not
be vented to the outside using the right side panel
because of the burner housing.
If the branch circuit to dryer is 15 ft. (4.5
m) or less in length, use UL (Underwriters
Laboratories) listed No.-10 AWg wire (copper
wire only), or as required by local codes. If
over 15 ft. (4.5 m), use UL-listed No.-8 AWg
wire (copper wire only), or as required by local
codes. Allow sufficient slack in wiring so the
dryer can be moved from its normal location
when necessary. Failure to do so may result in
fire, explosion, or death.
•
The dryer exhaust duct must be affixed securely to
the manufactured or mobile home structure, and
the exhaust duct must be made of a material that
will resist fire and combustion. It is recommended
that you use a rigid, semi-rigid or flexible metal
duct.
•
The power cord (pigtail) connection between
the wall receptacle and the dryer terminal block
IS NOT supplied with the dryer. Type of pigtail
and gauge of wire must conform to local codes
and with instructions on the following pages.
Failure to follow these instructions may result in
fire, explosion, or death.
•
•
•
DO NOT connect the dryer exhaust duct to any
other duct, vent, chimney, or other exhaust duct.
•
•
Make sure the dryer has adequate access to
outside fresh air to ensure proper operation. The
opening for outside fresh air must be at least 25 sq.
in (163 cm2).
A 4-wire connection is required for all mobile
and manufactured home installations, as well
as all new construction after January 1, 1996.
A 4-wire connection must be used where local
codes do not permit grounding through the
neutral wire. Failure to do so may result in fire,
explosion, or death.
It is important that the clearance of the duct from
any combustible construction be at least 2-inch
(5 cm), and when venting the dryer to the outdoors,
the dryer should be installed with a clearance of at
least 1 inch (2.5 cm) at the sides and back of the
dryer.
•
•
Please be aware that venting materials are not
supplied with the dryer. You must obtain the venting
materials necessary for proper installation.
Do not modify the plug and internal wire provided
with the dryer.
The dryer should be connected to a 4-hole outlet.
•
•
If the plug does not fit the outlet, a proper outlet will
need to be installed by a qualified electrician.
28 INSTALLATION
Attach the two hot leads of the power cord to the
outer terminal block screws.
5
6
7
WARNINg
Connect the power cord to the terminal block.
Each colored wire should be connected to the
same color screw. Wire color indicated on manual
is connected to the same color screw in the block.
Failure to follow these instructions may result in a
short or overload.
Attach the white neutral wire to the center screw
of the terminal block.
Attach the power cord ground wire to the green
ground screw.
Grounding through the neutral conductor is
prohibited for: (1) new branch-circuit installations,
(2) mobile homes, (3) recreational vehicles, and
(4) areas where local codes prohibit grounding
through the neutral conductor.
Tighten all screws securely.
8
9
Reinstall the terminal block access cover.
Hot
Neutral
(Black) (White)
Hot
(Red)
Four-Wire Power Cord
Ground
Screw
A 4-wire connection is required for
all mobile and manufactured home
installations, as well as all new
construction after January 1, 1996.
•
White Wire
moved from
Ground
Screw
Power Cord
Ground Wire
A UL-listed strain relief is required.
•
•
Use a 30-amp, 240-volt, 4-wire, UL-listed power
cord with #10 AWG-minimum copper conductor and
closed loop or forked terminals with upturned ends.
Remove the terminal block access cover on the
upper back of the dryer.
1
Install a UL-listed strain relief into the power cord
through-hole.
2
Thread a 30-amp, 240-volt, 4-wire, UL-listed
power cord with #10 AWG-minimum copper
conductor through the strain relief.
3
Terminal Block
UL-Listed
Strain Relief
UL-Listed 4-Wire Power Cord
Transfer the dryer’s ground wire from behind the
green ground screw to the center screw of the
terminal block.
4
NOTE
This dryer is supplied with the neutral wire
grounded. This white ground wire MUST BE
MOVED to the neutral terminal when a 4-wire
cord is to be used, or where grounding through
the neutral conductor is prohibited.
INSTALLATION 29
Four-Wire Direct Wire
Attach the two hot leads of the power cord to the
outer terminal block screws.
6
7
8
A 4-wire connection is required for
all mobile and manufactured home
installations, as well as all new
construction after January 1, 1996.
•
Attach the white neutral wire to the center screw
of the terminal block.
Attach the power cord ground wire to the green
ground screw.
A UL-listed strain relief is required.
•
•
Use UL-listed 4-wire #10 AWG-minimum copper
conductor cable. Allow at least 5 ft. (1.5 m) of wire
to allow for removal and reinstallation of the dryer.
Tighten all screws securely.
9
Remove 5-inch (12.7 cm) of the outer covering
Reinstall the terminal block access cover.
1
10
from the wire. Remove 5-inch (12.7 cm)
of insulation from the ground wire. Cut off
approximately 1½-inch (3.8 cm) from the other
three wires and strip 1 inch (2.5 cm) insulation
from each wire. Bend the ends of the three
shorter wires into a hook shape.
Neutral
(White)
Hot
(Black)
Hot
(Red)
Ground
Screw
White Wire
moved from
Ground
1" (2.5 cm)
Screw
Power Cord
Ground Wire
Ground Wire
5"
(12.7 cm)
Remove the terminal block access cover on the
upper back of the dryer.
2
Install a UL-listed strain relief into the power cord
through-hole.
3
4
Thread the 4-wire #10 AWG-minimum copper
power cable prepared in step 1 through the
strain relief.
Terminal Block
UL-Listed
Strain Relief
UL-Listed 4-Wire Power Cord
Transfer the dryer’s ground wire from behind the
green ground screw to the center screw of the
terminal block.
5
NOTE
This dryer is supplied with the neutral wire
grounded. This white ground wire MUST BE
MOVED to the neutral terminal when a 4-wire
cord is to be used, or where grounding through
the neutral conductor is prohibited.
30 INSTALLATION
Three-Wire Power Cord
Reinstall the terminal block access cover.
8
Neutral
(White)
Hot
(Black)
A 3-wire connection is NOT permitted
on new construction after January 1,
1996.
•
Hot
(Red)
Ground
Screw
A UL-listed strain relief is required.
•
•
Use a 30-amp, 240-volt, 3-wire, UL-listed power
cord with #10 AWG-minimum copper conductor and
closed loop or forked terminals with upturned ends.
White Wire
from Dryer
harness
Remove the terminal block access cover on the
upper back of the dryer.
1
External Ground
Wire (If required
by local codes)
Install a UL-listed strain relief into the power cord
through-hole.
2
Thread a 30-amp, 240-volt, 3-wire, UL-listed
power cord with #10 AWG-minimum copper
conductor through the strain relief.
3
Terminal Block
UL-Listed
Strain Relief
UL-Listed 3-Wire Power Cord
Attach the two hot leads (black and red) of the
power cord to the outer terminal block screws.
4
5
Attach the neutral (white) wire to the center
terminal block screw.
NOTE
The dryer is supplied with the neutral conductor
grounded. If a 3-wire cord is to be used and is
allowed, make sure the white neutral grounding
wire is connected to the green ground screw.
Connect the external ground (if required by local
codes) to the green ground screw.
6
7
Tighten all screws securely.
INSTALLATION 31
Reinstall the terminal block access cover.
Three-Wire Direct Wire
9
Hot
(Black)
Neutral
(White)
A 3-wire connection is NOT permitted
on new construction after January 1,
1996.
•
Hot
(Red)
Ground
Screw
A UL-listed strain relief is required.
•
•
Use UL-listed 3-wire, #10 AWG-minimum copper
conductor cable. Allow at least 5 ft. (1.5 m) length
to allow for removal and installation of dryer.
White Wire
from Dryer
harness
Remove 3½-inch (8.9 cm) of the outer covering
1
External Ground
Wire (If required by
local codes)
from the wire. Strip 1 inch (2.5 cm) insulation
from each wire. Bend the ends of the three wires
into a hook shape.
1" (2.5 cm)
Final Installation Check
Remove the terminal block access cover on the
upper back of the dryer.
2
Once you have completed the installation of the dryer
and it is in its final location, confirm proper operation
with the following tests and Installation Test (Duct
Check) on the following page.
Install a UL-listed strain relief into the power cord
through-hole.
3
4
Thread the 3-wire, #10 AWG-minimum copper
conductor power cable prepared in step 1
through the strain relief.
Testing Dryer heating
gAS mODELS
Terminal
Block
Close the dryer door, press the POWER button to turn
the dryer on, and start the dryer on a heat setting.
When the dryer starts, the igniter should ignite the
main burner.
UL-Listed
Strain Relief
ELECTRIC mODELS
Close the dryer door, press the POWER button to turn
the dryer on, and start the dryer on a heat setting.
The exhaust air should be warm after the dryer has
been operating for 3 minutes.
UL-Listed 3-Wire Power Cord
Attach the two hot leads (black and red) of the
power cord to the outer terminal block screws.
5
6
Checking Airflow
Attach the neutral (white) wire to the center
terminal block screw.
Effective dryer operation requires proper airflow.
The adequacy of the airflow can be measured by
evaluating the static pressure. Static pressure in the
exhaust duct can be measured with a manometer,
placed on the exhaust duct approximately 2 ft. (60.9
cm) from the dryer. Static pressure in the exhaust duct
should not exceed 0.6-inch (1.5 cm). The dryer should
be checked while the dryer is running with no load.
NOTE
The dryer is supplied with the neutral conductor
grounded. If a 3-wire cord is to be used and is
allowed, make sure the white neutral grounding
wire is connected to the green ground screw.
Connect the external ground (if required by local
codes) to the green ground screw.
7
8
Checking Levelness
Once the dryer is in its final location, recheck the
dryer to be sure it is level. Make sure it is level front
to back and side to side, and that all four leveling feet
are firmly on the floor.
Tighten all screws securely.
32 INSTALLATION
Check the display for results.
Installation Test (Duct Check)
4
During the test cycle, monitor the Flow Sense™
display on the control panel. If no bars are
displayed, when the cycle ends, the exhaust
system is adequate. If the exhaust system is
severely restricted, the display will show four
bars. Other problems may also be shown with
error codes. Refer to the next page for error
code details and solutions.
Once you have completed the installation of the
dryer, use this test to make sure the condition of the
exhaust system is adequate for proper operation of
the dryer. This test should be performed to alert you
to any serious problems in the exhaust system of
your home.
Your dryer features Flow Sense™, an innovative
sensing system that automatically detects
blockages and restrictions in dryer ductwork.
Keeping ductwork clean of lint buildup and free of
restrictions allows clothes to dry faster and reduces
energy use.
•
NO BARS:
OK
FOUR BARS:
RESTRICTED
NOTE
Four bars indicates that the exhaust system is
severely restricted. Have the system checked
immediately, as performance will be poor.
The dryer should be cool before starting this test.
If the dryer was warmed up during installation, run
the AIR DRY cycle for a few minutes to reduce
the interior temperature.
End of cycle.
5
At the end of the test cycle,
will display.
The test cycle will end and the dryer will shut off
automatically after a short delay.
To activate the installation test:
Remove the drying rack and literature, and
1
then close the door.
Do not load anything in the drum for this test, as
in may affect the accuracy of the results.
Check the error code before you call for service
•
Error
Code
Possible
Causes
Solutions
tE1
or
tE2
Temperature
sensor
failure.
•
•
Turn off the dryer and
call for service.
•
Press the Power button then immediately press
and hold both the Temp. and Signal buttons until
appears in the display.
2
Humidity
sensor
failure.
Turn off the dryer and
call for service.
•
•
hS
Check the power
supply or the
Electric
•
•
connection of the
power cord to the
terminal block. Refer
to the Connecting
Electric Dryers
section of this
dryer power
cord is not
connected
correctly, or
house power
supply is
Press the START/PAUSE button.
PS
or PF
or nP
3
manual for complete
instructions.
The dryer will start the test, which will last about
2 minutes. The heat will be turned on and the
temperatures in the drum will be measured.
incorrect.
House fuse is
blown, circuit
breaker
has tripped,
or power
• Reset circuit breaker
or replace fuse. Do
not increase the fuse
capacity.
If the problem is a
circuit overload, have
it corrected by a
outage has
occurred.
qualified electrician.
INSTALLATION 33
Check the duct condition
•
Restricted or Blocked Airflow
If the Flow SenseTM LED is turned on, check the
exhaust system for restrictions and damage. Repair
or replace the exhaust system as needed.
Avoid long runs or runs with multiple elbows or bends.
NOTE
When the dryer is first installed, this test should
be performed to alert you to any existing
problems with the exhaust duct in your home.
However, since the test performed during normal
operation provides more accurate information on
the condition of the exhaust duct than does the
installation test, the number of bars displayed
during the two tests may not be the same.
Excess or crushed
transition duct
Too many elbows or
exhaust too long
Do not interrupt the test cycle, as this could result
in inaccurate results.
Check for blockages and lint buildup.
Even if no bars are displayed during the test
cycle, some restrictions may still be present in the
exhaust system. Refer to the Venting the Dryer
section of this manual for complete exhaust
system and venting requirements.
Lint
buildup or
blockage
Your dryer features Flow Sense™, an innovative
sensing system that automatically detects
blockages and restrictions in the dryer ductwork.
Keeping ductwork clean of lint buildup and free
of restrictions allows clothes to dry faster and
reduces energy use.
Make sure the ductwork is not crushed or restricted.
Crushed
or
damaged
exhaust
34 OPERATION
OPERATION
WARNINg
To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the
ImPORTANT SAFETY INSTRUCTIONS, before operating this dryer.
Using the Dryer
1 Clean the Lint Filter
If the lint filter has not already been cleaned, lift out the filter and remove the lint
from the last load. This will help ensure the fastest and most efficient drying perfor-
mance. Make sure to reinstall the filter, pressing down until it clicks firmly into place.
The dryer will not operate without the lint filter in place.
2 Load the Dryer
Load the dryer with the wet laundry from the washer. If the load is extra large,
you may need to divide it into smaller loads for proper performance and fabric
care.
3 Turn on The Dryer
Press the POWER button to turn ON the dryer. The cycle LEDs will illuminate and a
chime will sound.
4 Select a Cycle
Turn the cycle selector knob either direction until the LED for the desired cycle
is on. The preset temperature, dry level, and option settings for that cycle will
be shown. Refer to page 37. Default settings for the selected cycle can now be
changed if desired. This can be done using the cycle modifier buttons as shown
on page 37. Cycle options can be added using the option buttons as shown on
page 38-41.
NOTE
Not all options or modifiers are available on all cycles. A different chime will
sound and the LED will not come on if the selection is not allowed.
5 Begin the Cycle
Press the START/PAUSE button to begin the cycle. The cycle can be paused at
any time either by opening the door or by pressing the START/PAUSE button.
If the cycle is not restarted within 4 minutes of being paused, the dryer will shut off
and the settings will be lost.
6 End of Cycle
When the cycle is finished, the chime will sound. Immediately remove your
clothing from the dryer to reduce wrinkling. If Wrinkle Care is selected, the dryer
will tumble briefly every few minutes to help prevent wrinkles from setting in the
clothes.
OPERATION 35
group Similar Items
Check the Lint Filter Before
Every Load
For best results, sort clothes into loads that can be
dried with the same drying cycle.
Always make sure the lint filter is clean before starting
a new load; a clogged lint filter will increase drying
time. To clean, pull the lint filter straight up and roll
any lint off the filter with your fingers. Do not rinse or
wash the filter to remove lint. Push the lint filter firmly
back into place. See Regular Cleaning for more
information.
Different fabrics have different care requirements, and
some fabrics will dry more quickly than others. For
best fabric care results, always dry fabrics with similar
care requirements together.
Always ensure the lint filter is properly installed before
running the dryer. Running the dryer with a loose or
missing lint filter will damage the dryer and articles in
the dryer.
Loading the Dryer
WARNINg
To reduce the risk of fire, electric shock, or
injury to persons when using this appliance,
follow basic precautions, including the
following:
Check all pockets to make sure that they are
empty. Items such as clips, pens, coins, and
keys can damage both your dryer and your
clothes. Flammable objects such as lighters
or matches could ignite, causing a fire.
Failure to do so may result in fire, explosion, or
death.
•
Lint Filter
Never dry clothes that have been exposed
to oil, gasoline, or other flammable
substances. Washing clothes will not
completely remove oil residues. Failure to
obey this warning may result in fire, explosion,
or death.
•
Sorting Loads
Fabric Care Labels
NOTE
Most articles of clothing feature fabric care labels that
include instructions for proper care.
Loading Tips
Combine large and small items in the same
load.
•
Fabric Care Labels
Tumble dry
Damp clothes will expand as they dry. Do not
overload the dryer; clothes require room to
tumble and dry properly.
•
Normal
Dry
Permanent Press/
wrinkle resistant
Close zippers, hooks, and drawstrings to
prevent these items from snagging or tangling
on other clothes.
•
Gentle/
Do not
Do not dry
delicate tumble dry (used with do not wash)
Heat setting
High
Medium
Low
No heat/air
36 OPERATION
Using the Lg EasyLoadTm
hamper Door (on some models)
Use the hamper door when loading. The hamper door
opens about 40 degrees and acts as a chute to help
guide items into the drum and help prevent items from
falling onto the floor. It also comes in handy when
unloading a few small items, helping prevent the rest
of the laundry from being pulled onto the floor.
Swing Door
Use the swing door when unloading, or when loading
bulkier items, for easy access to the drum.
To open the swing door, grasp the top of the door on
the side opposite the hinge and pull.
To open the hamper door, press the release on the
top of the door and pull the door forward.
NOTE
Make sure the hamper door release is completely
closed before using the swing door.
Make sure laundry is fully inserted in the drum before
closing the door.
NOTE
Make sure the swing door latch is completely
closed before pressing the hamper door release.
Hamper door release
Interlock
Buttons
Swing door
40°
WARNINg
Do not press the three interlock buttons when
the door is open. The door may fall off and cause
serious injury.
Hamper door
Do not place heavy items on or lean against
•
the top of the door when it is open.
WARNINg
Do not attempt to pull the hamper door open
more than 40 degrees.
The dryer could tip forward, causing injury or
propert damage.
•
•
Be careful when opening and closing the door.
Fingers and hands can get caught in the door
and cause injury if the door drops forward
unexpectedly.
OPERATION 37
Control Panel
1
2
3
4
5
6
8
7
4
NOTE
Model numbers can be found on the cabinet inside the door.
1
5
POWER Button
Time and Status Display
Press to turn the dryer ON. Press again to turn the
dryer OFF.
The display shows the settings, estimated time
remaining, options, and status messages for your
dryer.
NOTE
Pressing the POWER button during a cycle will
cancel that cycle and any load settings will be
lost.
6
mORE TImE/LESS TImE Buttons
Use these buttons with the Time Dry and other
MANUAL DRY cycles to adjust the drying time.
Press the more Time button to increase the selected
manual cycle time by 1 minute; press the Less Time
button to decrease the cycle time by 1 minute.
2
Cycle Selector Knob
Turn this knob to select the desired cycle. Once
the desired cycle has been selected, the standard
presets are shown in the display. On Manual Dry
cycles, these settings can be adjusted using the cycle
modifier buttons any time before starting the cycle.
7
Cycle modifier Buttons
Use these buttons to select the desired cycle settings
for the selected cycle. The current settings are shown
in the display. Press the button for that option to
select other settings.
3
START/PAUSE Button
Press this button to start the selected cycle. If the
dryer is running, use this button to pause the cycle
without losing the current settings.
8
Steam Functions
LG’s steam technology allows you to inject fabrics
with a swirling jet of steam to refresh clothes, reduce
static, and make ironing easier. Simply select the
Steam Fresh™ cycle or Wrinkle Free cycle.
NOTE
If you do not press the START/PAUSE button to
resume a cycle within 4 minutes, the dryer turns
off automatically.
4
Cycle option Buttons
The option buttons allow you to select additional cycle
options. Certain buttons also allow you to activate
special functions by pressing and holding the button
for 3 seconds.
38 OPERATION
9
10
11
12
14
13
9
13
Estimated Time Remaining
Custom Pgm
If you have a special combination of settings that
you use frequently, you can save these settings as a
Custom Program.
This display shows the estimated time remaining for
SENSOR DRY cycles or the actual time remaining for
Time Dry or MANUAL DRY cycles.
NOTE
Flow Sense™ Duct Blockage Sensing System
Indicator
10
The cycle time on SENSOR DRY cycles may
fluctuate as the dryer recalculates drying time for
optimal results.
The Flow Sense™ duct blockage sensing system
detects and alerts you to blockages in the ductwork
that reduce exhaust flow from the dryer. Maintaining
a clean exhaust system improves operating efficiency
and helps minimize service calls, saving you money.
14
Child Lock Indicator
When Child Lock is set, the Child Lock indicator will
appear and all buttons will be disabled except the
POWER button. This prevents children from changing
settings while the dryer is operating.
11
Clean Filter Reminder
The display will show Clean Filter when the dryer is
turned on as a reminder to check the filter. It turns off
when the START/PAUSE button is pressed.
12
Cycle Completion Indicator with Check Filter
Reminder
This portion of the display shows which stage of the
drying cycle is currently underway (Clean Filter, Dry,
Cool).
OPERATION 39
= default setting
= allowable option
Cycle guide
more
Damp
Dry
Signal
Time/ Wrinkle Turbo
Less
Time
Reduce Energy
Static Saver
Cycle
Fabric Type
Dry Level
Temperature
Time
Care
Steam
Comforter,
Mid High
10
Steam
Shirts,Trousers
(except especially
delicate fabrics)
Off
FreshTM
Adjustable Adjustable
Steam
Comforter, Bedding,
Children’s clothing
Off
High
High
31
SanitaryTM
Anti-
Bacterial
Do not use this cycle
with delicate fabrics.
Very Dry
1:10
Only Normal &
Cotton/Towels
Fabric Type
(Max 3 lb)
Normal Dry
Adjustable
Small Load
Bedding
High
30
Normal Dry
Adjustable
Normal Dry
Adjustable
Normal Dry
Adjustable
Normal Dry
Adjustable
Normal Dry
Adjustable
Comforters, Pillows,
Shirts
Medium
High
55
54
Heavy
Duty
Jeans, heavyweight
items
Elec : 67
Gas : 63
Work clothes,
corduroys, etc.
Normal
Medium
Low
Perm.
Press
Permanent press,
synthetic items
32
Denims, towels,
heavy cottons
Towels
Mid High
-
55
27
Sportswear Sports Wear
Off
Normal Dry
Adjustable
Lingerie, sheets,
Delicates
Low
28
25
blouses
High
For small loads with
Speed Dry
Off
Off
short drying times
Adjustable Adjustable
For items that require
heat-free drying such
as plastics or rubber
30
No Heat
Air Dry
Adjustable
40 OPERATION
Sensor dry cycles
manual dry cycles
Sensor dry cycles utilize LG’s unique dual sensor
system to detect and compare the moisture level
in clothes and in the air and adjust the drying time
as needed to ensure superior results. The dryer
automatically sets the dryness level and temperature
at the recommended setting for each cycle. The
estimated time remaining will be shown in the display.
Use manual dry cycles to select a specific amount
of drying time and a drying temperature. When a
manual dry cycle is selected, the Estimated Time
Remainng display shows the actual time remaining
in your cycle. You can change the actual time in the
cycle by pressing More Time or Less Time.
NOTE
CERTIFIED BY NSF/P154
To protect your garments not every dryness level,
temperature, or option is available with every
cycle. See the Cycle guide for details.
NSF International (formerly the National Sanitation
Foundation), certifies that the Anti Bacterial cycle
reduces 99.9% of bacteria on laundry, and none of
the bacteria will carry over onto the next laundry load.
Downloaded
The default settings for the Anti Bacterial cycle
are high temperature and Very Dry. These default
settings cannot be changed.
•
If you download a cycle using the Tag On feature,
it will be placed in the downloaded cycle position.
Choose the Downloaded cycle to run the downloaded
cycle.
Do NOT use this cycle with delicate items or
fabrics.
•
OPERATION 41
Cycle Option Buttons
Cycle Settings and Options
The dryer features several additional cycle options to
customize cycles to meet individual needs. Certain
option buttons also feature a special function that
can be activated by pressing and holding that option
button for 3 seconds. (See Special Functions on the
following page for details.)
Cycle Modifier Buttons
SENSOR DRY cycles have preset settings that
are selected automatically. MANUAL DRY cycles
have default settings, but you may also customize
the settings using the cycle modifier buttons. Press
the button for that option to view and select other
settings.
Adding Cycle Options to a Cycle:
Turn on the dryer and press the CYCLE buttons
to select the desired cycle.
1
Dry Level
Selects the level of dryness for the cycle. Press
the Dry Level button repeatedly to scroll through
available settings.
Use the cycle modifier buttons to adjust the
settings for that cycle.
2
This option is only available with SENSOR DRY
cycles.
•
Press the cycle option button(s) for the option
you would like to add. A confirmation message is
shown in the display.
3
The dryer will automatically adjust the cycle time.
Selecting More Dry or Very Dry will increase
the cycle time, while Less Dry or Damp Dry will
decrease the cycle time.
•
Press the START/PAUSE button to start the
cycle. The dryer starts automatically.
4
Use a Less Dry or Damp Dry setting for items that
you wish to iron.
•
Wrinkle Care
Selecting this option will tumble the load periodically
for up to 3 hours after the selected cycle, or until the
door is opened. This is helpful in preventing wrinkles
when you are unable to remove items from the dryer
immediately.
Temp.
Adjusts the temperature setting. This allows precise
care of your fabrics and garments. Press the Temp.
Control button repeatedly to scroll through available
settings.
Damp Dry Signal
With this option, the dryer will signal when the load
is approximately 80% dry. This allows you to remove
faster- drying lightweight items or items that you
would like to iron or hang while still slightly damp.
Time Dry
Allows you to manually select the drying time, from 20
to 60 minutes, in 10-minute increments. Use this for
small loads or to remove wrinkles.
more Time/Less Time
Use the more Time/Less Time buttons to add or
reduce the drying time of a MANUAL DRY cycle in
1-minute increments.
Signal (Option)
Press the Signal (Option) button repeatedly to
change the volume or turn on/off the button tones and
the end of cycle melody.
42 OPERATION
Custom Pgm
Special Functions
If you have a special combination of settings that
you use frequently, you can save these settings as a
custom program.
Some cycle option buttons also activate secondary
functions. These special functions are marked with an
asterisk (*). Press and hold the option button marked
with the special function to activate it.
Saving a Custom Program:
* Drum Light
Turn on the dryer and press the CYCLE buttons
to select the desired cycle.
1
The drum is equipped with a blue LED that illuminates
when the dryer is turned on. This light automatically
turns off when the door is closed and the cycle starts.
To turn on the light during a cycle, press and hold the
TurboSteam button for three seconds. The drum light
will illuminate and then turn off automatically after four
minutes.
Use the cycle setting buttons to adjust the
settings for that cycle.
2
Press the cycle option button(s) for the option you
would like to add. A confirmation message will be
shown in the display.
3
Press and hold the Custom Pgm button for 3
seconds.
4
* Child Lock
Use this option to prevent unwanted use of the dryer
or to keep cycle settings from being changed while
the dryer is operating.
NOTE
You may save only one custom program at a
time. Pressing and holding the Custom Pgm
button will overwrite any previously saved custom
program.
Press and hold the button marked Child Lock for
3 seconds to activate or deactivate the Child Lock
function. The Child Lock icon will be shown in the
display, and all controls will be disabled except the
POWER button.
Recalling a Custom Program:
NOTE
Turn on the dryer.
1
Once set, Child Lock remains active until it is
manually deactivated. Child Lock must be turned off
to run another cycle. To deactivate Child Lock, press
and hold the Child Lock button for 3 seconds.
Press the Custom Pgm button.
2
Press the START/PAUSE button to start the
cycle.
3
Energy Saver (on some models)
This option helps to reduce energy consumption in
the Normal cycle, depending on the load size.
When the Energy Saver option is selected, the cycle
begins with an air dry section and the drying time is
increased.
NOTE
The Energy Saver option is turned on by default in
the Normal cycle. Turn off the Energy Saver option
for a faster Normal cycle which begins with heated
drying.
* Default On/Off
This option allows the Energy Saver settings to be
changed. To run a Normal cycle without the Energy
Saver option, press and hold the Energy Saver button
for three seconds. ON or OFF appears in the display.
OPERATION 43
Using the steam options:
Steam Functions
The Reduce Static option injects steam late in the
drying cycle to reduce the static electricity caused
by dry fabrics rubbing together. Change the amount
of time for the cycle by pressing the More Time or
Less Time button, depending on the load (quantity
of items). The display will show the recommended
number of items, such as 7, 9, 11, 14, 16, or 18.
TurboSteam helps prevent the overdrying of clothes
by injecting steam during the drying process. The
Steam Shield Function extends the life of clothes.
LG’s new steam technology allows you to inject
fabrics with a swirling jet of hot steam to refresh
clothes and reduce static, or sanitize clothes.
Simply select the Steam Fresh™ cycle or the Steam
Sanitary™ cycle. Or you can add a steam option to
selected cycles.
Using the Steam Fresh™ cycle
Steam Fresh™ uses the power of steam alone to
quickly reduce wrinkles and odors in fabrics. It brings
new life to wrinkled clothes that have been stored for
an extended time. Steam Fresh™ can also be used
to help reduce odors and remove the hanger creases
in fabrics.
NOTE
When Sensor Dry is selected with the Reduce
Static or Turbo Steam option, a Dry level of Less
or Damp cannot be selected.
•
The Reduce Static option may also be selected
during Time Dry cycles.
•
•
NOTE
Depending on the load size, change the cycle time
by pressing More Time or Less Time. The display
•
After the Steam option is selected in Time Dry, the
More Time or Less Time buttons will change the
steam time only.
shows 1, 3, 5, or
. Select 3 for up to three
items; select 5 for four or five items; and select
for a large load, a bulky item like a blanket,
or to remove hanger creases.
After pressing Start/Pause, the More Time or Less
Time buttons will be disabled.
•
To add steam to a standard cycle:
To use the Steam Fresh™ cycle:
Turn on the dryer and turn the cycle selector
knob to select the desired cycle.
Turn on the dryer and turn the cycle selector
knob to select the Steam Fresh™ cycle.
1
1
Use the cycle setting buttons to adjust the
settings for that cycle.
To add an option function, select Wrinkle Care.
2
2
Press the steam option button for the steam
option you would like to add. Then adjust for
the load size using the More Time or Less Time
buttons.
Depending on the load (quantity of items), steam
time can be changed by pressing the More Time
or Less Time buttons.
3
3
Press Start/Pause button to start the cycle.
4
Press Start/Pause to start the cycle.
4
Using the Steam Sanitary™ cycle
The new Steam Sanitary™ cycle is ideal for sanitizing
non-washable items quickly and easily using the
power of steam alone. This cycle is recommended for
use with cotton and polyester materials. (Do NOT use
for urethane foam, down feathers or delicate items.)
44 OPERATION
NOTE
WARNINg
Do not open the dryer door during steam
cycles. Failure to follow this warning can cause
serious injury or death.
When Sensor Dry is selected with the Reduce
Static or Turbo Steam option, a dry level of Less
or Damp cannot be selected.
•
•
•
The Reduce Static option may also be selected
during Time Dry cycles.
•
•
Do not fill the steam feeder with gasoline,
drycleaning solvents, or other flammable or
explosive substances. Failure to do so can
result in death, explosion, fire, or burns.
After the steam option is selected in Time Dry, the
More Time or Less Time buttons will change the
steam time only.
Do not touch the steam nozzle in the drum
during or after the steam cycle. Failure to
follow this warning can cause serious injury or
death.
•
After pressing Start/Pause, the More Time or Less
Time buttons will be disabled.
•
Steam Cycle guide
Temp.
Control
Fabric
State
maximum
Amount
Steam
Default Time
Dry Level
Fabric Type
Comforter
Bedding
Single (1 each)
3 lbs.
Steam
31 minutes
10 minutes
Dry
Dry
Sanitary™
Children’s
clothing
Comforter
Shirts*
Single (1 each)
5 each
Steam
Fresh™
+
Varies by
8 lbs.
Reduce
Static
Wet
Wet
Wet
selected cycle
(18 Items.)
Follows
Selected
Cycle
Steam
Option
+
Varies by
selected cycle
8 lbs.
(18 Items)
Turbo
Steam
+
Varies by
selected cycle
8 lbs.
(18 Items.)
Reduce
Static
38 minutes
Time Dry
*Shirt: 70% cotton:30% poly blend. Except especially delicate fabrics.
When the lint filter or exhaust duct is clogged, steam options will not give proper results.
For best results, load articles of similar size and fabric type. Do not overload.
•
•
SMART FEATIRES 45
Using the Tag On Function
SmART FEATURES
The Tag On Icon
Tag On (on some models)
Look for the Tag On icon on the right side of the
dryer's control panel. Position the smart phone over
the icon when using the Tag On function with the LG
Smart Set features of the LG Smart Laundry & DW
application.
Before Using Tag On
The Tag On function allows you to conveniently use
the LG Smart Diagnosis™, Cycle Download, Laundry
Stats and Tag On Cycle Set features to communicate
with the appliance from a smart phone. To use the
Tag On function:
Download the LG Smart Laundry & DW
application to the smart phone.
1
Turn on the NFC (Near Field Communication)
function on the smart phone. The Tag On
2
function can only be used with smart phones
equipped with the NFC function and based on
the Android operating system (OS).
Turning On the Smart Phone’s NFC Function
Enter the Settings menu of the smart phone and
select Share & connect.
1
The NFC Antenna Position
When you use the Tag On function, position your smart
phone so that the NFC antenna inside the back of
your smart phone matches the position of the Tag On
icon on the appliance. (Because you cannot see the
position of the antenna, the LG Smart Laundry & DW
app will attempt to find it for you and show you a target
range for the antenna on your smart phone’s screen.)
Set NFC to ON.
2
If the app is not able to show a target range, try
positioning the center back of your smart phone over
the Tag On icon on the appliance. If the connection
is not made immediately, move your smart phone
very slightly in a widening circular motion until the
application verifies the connection.
Because of the characteristics of NFC, if the
transmission distance is too far, or if there is a metal
sticker or a thick case on the phone, transmission will
not be good.
NOTE
Press [
] in the LG Smart Laundry & DW app for
Depending on the smart phone manufacturer and
Android OS version, the NFC activation process
may differ. Refer to the manual of the smart
phone for details.
a more detailed guide on how to use the Tag On
function.
46 SMART FEATIRES
Using Tag On With Apps
Touch the Tag On logo.
2
3
LG Smart Diagnosis™, Cycle Download, Laundry
Stats and Tag On Cycle Set in the LG Smart Laundry
& DW apps use the Tag On function when you touch
the LG appliance’s Tag On logo with your NFC-
equipped smart phone.
NOTE
Images are for reference only. The actual LG
Smart Laundry & DW application is subject to
change for product improvement purposes.
Before using the LG Smart Diagnosis™, Cycle
Download, Laundry Stats and Tag On Cycle Set,
download the application from the Google Play
Store and install it.
•
•
Check the diagnosis results and solutions.
Select Tag On using either the scrollable icons or
the stationary bottom icons.
The app shows the diagnosis results of the
cycles recently used.
•
•
If the results are unclear, or if they suggest
calling the LG Service Center, see the Call
Center Diagnosis section for instructions.
Tag On Diagnosis
Call Center Diagnosis
The Tag On Diagnosis app helps you to troubleshoot
problems with your appliance using the Tag On
function and an NFC-equipped smart phone based
on the Android operating system (OS).
If you receive a diagnosis from either the Tag On
Diagnosis or Smart DiagnosisTM app that is unclear or
directs you to call the LG Service Center, follow these
instructions:
Select Tag On Diagnosis.
1
Select Press to Call Lg Service on the Smart
Diagnosis Result screen.
1
Select your country.
2
SMART FEATIRES 47
Tag On Cycle Download
Agree to Terms and Conditions of the Use and
Privacy Policy by pressing I accept.
3
4
Tag On Cycle Download allows you to download
cycles for later use. The cycle is available at the
Download Cycle position on the control panel until
another cycle is downloaded.
Select Tag On Cycle Download.
1
Enter your phone number in the field. Use this
phone number when talking to LG Customer
Service to allow them to find your Smart
Diagnosis data.
Touch the Tag On logo.
2
Press the Call button to initiate the call to LG’s
Support Center.
5
Select a cycle to download.
3
The current downloaded cycle is at the top
of the screen and the available cycles are
below that. You can also confirm the existing
downloaded cycle.
•
48 SMART FEATIRES
Flow SenseTm Status
Touch the Tag On logo.
4
LG’s Flow Sense duct blockage sensing system
detects and alerts you to restrictions in the installed
household ductwork that reduce exhaust airflow
through the dryer.
•
When a Tag On screen appears, tap your
smart phone on the Tag On icon on the right
side of the dryer’s control panel.
•
Select Laundry Stats.
1
The new cycle is downloaded successfully!
5
Touch the Tag On logo.
2
Check whether the new cycle is downloaded
by turning the cycle selector knob to Download
Cycle.
•
Check the Flow Sense status result.
3
4
Laundry Stats
Tag On Laundry Stats allows you to check the Flow
Sense status on your appliance to check if your
home exhaust system is clogged and also display the
details of your last ten cycles.
If the status shows your home exhaust system is
blocked, press the Venting Tips button.
SMART FEATIRES 49
Run Cycle Again
Tag On Cycle Set
Tag On Cycle Set allows you to automatically adjust
the cycle and settings based on your laundry needs.
Select the Run Cycle Again button.
1
The Most Used cycle or Most Recent cycle
can be immediately started by selecting the
Run Cycle Again button.
•
Select Tag On Cycle Set.
1
Touch the Tag On logo.
2
Touch the Tag On logo.
2
3
Select a laundry category based on the issue
you want the machine to focus on.
3
Check whether drying starts with the selected
cycle.
The screen shown above appears and drying
starts immediately on the selected cycle.
•
50 SMART FEATIRES
After selecting the category, a list of specific
cycles will appear. Select the cycle based on
your needs.
4
When the Tag On screen appears, tap your
smart phone to the Tag On logo on the right side
of the dryer’s control panel.
5
After tagging the machine with your phone,
the cycle will automatically start. Verify that the
correct cycle and settings were selected.
6
MAINTENANCE 51
maintaining Ductwork
mAINTENANCE
Regular Cleaning
WARNINg
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
Vent ductwork should be checked for lint buildup once
per month and cleaned at least once per year. If any
noticeable reduction in airflow or drying performance
occurs, immediately check ductwork for obstructions
and blockages. Contact a qualified technician or
service provider.
Cleaning the Lint Filter
Unplug the dryer before cleaning to avoid
the risk of electric shock. Failure to follow
this warning may cause serious injury, fire,
electrical shock, or death.
•
Always clean the lint from the filter after every cycle.
Never use harsh chemicals, abrasive
cleaners, or solvents to clean the washer.
They will damage the finish.
•
Cleaning the Exterior
Lint Filter
Proper care of your dryer can extend its life. The
outside of the machine can be cleaned with warm
water and a mild, nonabrasive household detergent.
Immediately wipe off any spills with a soft, damp cloth.
To clean, open the dryer door and pull the lint filter
straight up. Then:
NOTE
For everyday cleaning, roll any lint off the filter
with your fingers, or
1
Do not use methylated spirits, solvents, or
similar products.
•
•
Never use steel wool or abrasive cleansers;
they can damage the surface.
Cleaning the Interior
Wipe around the door opening and seal with a soft,
damp cloth to prevent lint and dust buildup that could
damage the door seal.
Vacuum the lint filter.
2
Clean the window with a soft cloth dampened with
warm water and a mild, nonabrasive household
detergent, then wipe dry.
The stainless steel drum can be cleaned with a
conventional stainless steel cleaner, used according
to the manufacturer’s specifications. Never use steel
wool or abrasive cleansers; they may scratch or
damage the surface.
If the lint filter has become very dirty or clogged
3
with fabric softener, wash the lint filter in warm,
soapy water and allow it to dry thoroughly before
reinstalling.
Cleaning Around and Under the Dryer
Vacuum lint and dust from around the dryer and
underneath it regularly. Vent ductwork should be
checked for lint buildup and cleaned at least once per
year. If any noticeable reduction in airflow or drying
performance occurs, immediately check ductwork for
obstructions and blockages.
NOTE
NEVER operate the dryer without the lint filter in
place. NEVER operate the dryer with a wet lint
filter.
52 TROUBLESHOOTING
TROUBLEShOOTINg
FAQs: Frequently Asked Questions
Q:
When I press a button, why does my dryer beep and then nothing happens?
A:
The Child Lock feature is turned on. To turn off Child Lock, turn the dryer on, then press and hold the
button that has *Child Lock on or under it for 3 seconds.
Q:
Why does my dryer take so long to dry clothes?
A:
Proper airflow is critical to the efficient operation of clothes dryers. A lint filter which is full of lint or
clogged with fabric softener sheet residue can reduce the airflow to the point that the time required
to dry clothing will be greatly increased. Another factor affecting dry time is your home exhaust
system. An exhaust system which is dirty and clogged with lint, or is excessively long, needs to be
professionally cleaned or repaired.
Q:
Why does my dryer start by itself every few minutes?
A:
This is how the Wrinkle Care feature works. The dryer runs briefly every few minutes for up to 3 hours
after the cycle finishes. This feature is designed to help prevent wrinkles from setting in when the
dryer is not unloaded immediately after the cycle is finished.
Q:
Why does my dryer show 3 minutes when I select the Steam FreshTm cycle?
A:
When the Steam FreshTM cycle is selected, the dryer displays the number of garments rather than the
estimated cycle time, until the cycle is started. Use the More Time or Less Time buttons to adjust the
load size setting for the number of garments you desire. For a large load or single bulky item use the
(big) setting.
User Support Videos
For further assistance, there are videos and tutorials
available through the LG.com website.
On the lg.com/us home page, hover over the
Support menu tab to bring up the menu selections.
1
Select Videos & Tutorials.
Type Dryer in the search box on the new page and
click the Search button.
2
Scan this QR code to quickly access the
video search page on the LG website.
Once there, type Dryer in the search box.
TROUBLESHOOTING 53
Before Calling for Service
This dryer is equipped with an automatic error-monitoring system to detect and diagnose problems at an early
stage. If the dryer does not function properly or does not function at all, check the following before you call for
service.
Operation
Problem
Possible Cause
Solutions
After clearing the restriction, the
Flow SenseTm system requires
multiple, consecutive cycles to
determine that the performance
value has improved before the
Flow SenseTm indicator is reset.
The Flow SenseTm
indicator remains
active after clearing
the restriction in the
venting.
If the Flow SenseTM indicator remains
active for more than five cycles after
the restriction has been cleared, call for
service.
Make sure that the plug is securely
plugged into a grounded outlet matching
the dryer’s rating plate.
Power cord is not properly
plugged in.
Dryer will not turn on
Reset circuit breaker or replace fuse. Do
not increase fuse capacity. If the problem
is a circuit overload, have it corrected by
a qualified electrician.
house fuse is blown, circuit
breaker has tripped, or power
outage has occurred.
Reset circuit breaker or replace fuse. Do
not increase fuse capacity. If the problem
is a circuit overload, have it corrected by
a qualified electrician.
house fuse is blown, circuit
breaker has tripped, or power
outage has occurred.
NOTE
Due to the design of electric dryers,
it is possible for a circuit problem to
allow an electric dryer to run without
heat.
Confirm that the house gas shutoff and
the dryer gas shutoff valves are both fully
open. Even if gas is not supplied to the
dryer, it will run and no error codes will
display. Verify that other gas appliances in
the home are working normally.
Dryer does not heat
gas supply or service is turned
off (gas models only).
If using the Cotton/Normal cycle, deselect
the energy saver option. The Energy
Saver option is selected by default. This
option reduces energy use by adding
an air dry section to the beginning of the
cycle. It is normal to feel no heat at the
beginning of the cycle while in Energy
Saver mode.
Energy Saver option selected
(on some models)
Power cord connection is
incorrect.
Check the connectriction of power cord to
the terminal block.
Display show error
code nP or gAS
gas supply or service turned off
(gas models only).
Confirm that house gas shutoff and the
dryer gas shutoff are both fully open
54 TROUBLESHOOTING
Problem
Possible Cause
Solutions
Confirm that the exhaust duct is properly
configured and free of debris, lint, and
obstructions. Make sure that outside wall
dampers can open properly and are not
blocked, jammed, or damaged.
Exhaust ducts are blocked, dirty,
or duct run is too long.
Clothes take too long to
dry
Separate heavy items from lightweight
items. Larger and heavier items take
longer to dry. Light items in a load with
heavy items can fool the sensor because
the light items dry faster.
Load is not properly sorted.
Heavy fabrics take longer to dry because
they tend to retain more moisture. To help
reduce and maintain more consistent
drying times for large and heavy fabrics,
separate these items into smaller loads of
a consistent size.
Large load of heavy fabrics.
Use the appropriate control settings for
the type of load you are drying. Some
loads may require an adjustment of the
dry level setting for proper drying.
Dryer controls are not set
properly.
Remove the lint from the filter before
every load. With the lint removed, hold
the filter up to a light to see if it is dirty or
clogged. With some loads that produce
high amounts of lint, such as new bath
towels, it may be necessary to pause the
cycle and clean the filter during the cycle.
Lint filter needs to be cleaned.
Reset circuit breaker or replace fuse. Do
not increase fuse capacity. If the problem
is a circuit overload, have it corrected by
a qualified electrician.
Clothes take too long to
dry
house fuse is blown, circuit
breaker has tripped, or power
outage has occurred.
NOTE
Due to the design of electric dryers,
it is possible for a circuit problem to
allow an electric dryer to run without
heat.
Divide extra large loads into smaller
loads for better drying performance and
efficiency.
Dryer is overloaded.
Dryer is underloaded.
If you are drying a very small load, add a
few extra items to ensure proper tumbling
action. If the load is very small and you
are using SENSOR DRY cycles, the
electronic control cannot properly sense
the dryness of the load and may shut off
too soon. Use TIME DRY or add some
extra wet clothes to the load.
TROUBLESHOOTING 55
Problem
Possible Cause
Solutions
If using the Cotton/Normal cycle, deselect
the Energy Saver option. This option
reduces energy use by adding an air dry
section to the beginning of the cycle.
Clothes take too long to Energy Saver option selected
dry
(on some models)
The drying time for a load will vary
depending on the type of heat used
(electric, natural gas, or LP gas), the
size of the load, the type of fabrics, the
wetness of the clothes, and the condition
of the exhaust duct and lint filter. Even an
unbalanced load in the washer can cause
poor spinning, resulting in wetter clothes
which will take longer to dry.
heat settings, load size, or
dampness of clothing is not
consistent.
Drying time is not
consistent
56 TROUBLESHOOTING
Performance
Problem
Possible Cause
Solutions
Confirm and follow the instructions
provided with your fabric softener.
Fabric softener used incorrectly.
Use your dryer to dry only clean items.
Soil from dirty clothes can transfer to the
clean clothes in the same or later loads.
Clean and dirty clothes are being
dried together.
greasy or dirty spots
on clothes
Stains on dried clothes could be stains
that were not removed during the washing
process. Make sure that clothes are being
completely cleaned or rinsed according
to the instructions for your washer and
detergent. Some difficult soils may require
pre-treating prior to washing.
Clothes were not properly
cleaned or rinsed before being
placed in the dryer.
Over drying a load of laundry can lead to
wrinkled clothes. Try a shorter drying time
or LESS DRY setting and remove items
while they still retain a slight amount of
moisture.
Clothes dried too long (over
dried).
Clothes are wrinkled
Use the WRINKLE CARE option. This
Clothes left in dryer too long after feature will tumble the clothes briefly
cycle ends.
every few minutes for up to 3 hours to
help prevent wrinkling.
To avoid shrinking your clothes, always
consult and follow fabric care instructions.
garment care instructions are not Some fabrics will naturally shrink when
Clothes are shrinking
being followed.
washed. Other fabrics can be washed but
will shrink when dried in a dryer. Use a
low or no heat setting.
Remove the lint from the filter before
every load. With the lint removed, hold
the filter up to a light to see if it is dirty
or clogged. If it looks dirty, follow the
cleaning instructions. With some loads
that produce high amounts of lint, it may
be necessary to clean the filter during the
cycle.
Lint filter not cleaned properly.
Laundry not sorted properly.
Lint on clothes
Some fabrics are lint producers (i.e., a
fuzzy white cotton towel) and should be
dried separately from clothes that are lint
trappers (i.e., a pair of black linen pants).
TROUBLESHOOTING 57
Problem
Possible Cause
Solutions
Use a fabric softener to reduce static
electricity. Be sure to follow the
manufacturer’s instructions. Overdrying
a load of laundry can cause a buildup of
static electricity. Adjust settings and use a
shorter drying time, or use SENSOR DRY
cycles.
Excess static in clothes.
Lint on clothes
Divide extra large loads into smaller loads
for drying.
Dryer is overloaded.
Check pockets thoroughly before washing
and drying clothes.
Tissue, paper, etc., left in pockets.
Use a fabric softener or the STATIC
SHIELD option, if equipped, to reduce
static electricity. Be sure to follow the
manufacturer’s instructions.
Fabric softener is not used or
used incorrectly.
Overdrying a load of laundry can cause
a buildup of static electricity. Adjust
settings and use a shorter drying time, or
use AUTO DRY cycles. Select a LESS
DRY setting on SENSOR DRY cycles, if
necessary.
Excess static in clothes Clothes dried too long
after drying
(overdried).
These fabrics are naturally more prone to
static buildup. Try using fabric softener, or
use LESS DRY and/or shorter TIME DRY
time settings.
Drying synthetics, permanent
press, or synthetic blends.
If items are too tightly packed or too
sparse the sensor may have trouble
reading the dryness level of the load. Use
a Time Dry cycle for very small loads.
Large, bulky items such as blankets
or comforters can sometimes wrap
themselves into a tight ball of fabric. The
outside layers will dry and register on the
sensors, while the inner core remains
damp. When drying a single bulky item, it
may help to pause the cycle once or twice
and rearrange the item to unwrap and
expose any damp areas.
Very large load or very small load.
Clothes have damp
spots after a SENSOR
DRY cycle.
Single large item such as a
blanket or comforter.
To dry a few remaining damp items from
a very large load or a few damp spots
on a large item after a sensor cycle has
completed, empty the lint trap, then set a
Time Dry cycle to finish drying the item(s).
58 TROUBLESHOOTING
Steam Functions (Steam models)
Problem
Possible Cause
Solutions
Water drips from nozzle
when STEAm CYCLE
starts
This is steam condensation. The dripping
water will stop after a short time.
This is normal.
Small loads of 1 to 5 items work best.
garments still wrinkled
Too many or overly different
types of garments in dryer.
after Steam FreshTm
Load fewer garments. Load similar types
of garments.
Creases or pleats are
gone from garments
after Steam FreshTm
The function of this cycle is to
remove wrinkles from fabric.
Use an iron to replace creases and pleats
in garments.
garments have static
after using the Reduce
Static option
The amount of static experienced will
depend on the individual moisture level in
the skin.
This is normal.
garments are too damp
or too dry after using
the Reduce Static
option
Correct drying options not
selected.
Select the load weight manually before
starting the Reduce Static option.
garments are not
uniformly damp after
using the Easy Iron
option
Number of garments or load
size not properly selected at the
beginning of the cycle.
Select the correct number of garments or
load size before starting the cycle.
Steam does not
generate, but no error
code is shown
Water level error.
Unplug dryer and call for service.
Condensation will normally form on the
inside of the dryer door during steam
operation. Some condensation may drip
out the bottom of the door.
Water drips from door
during STEAm CYCLE
This is normal.
Steam vapor is difficult to see when the
door is closed. However, condensation
will normally form on the inside of
the dryer door if the steam system is
operating normally.
Steam is not visible
during STEAm CYCLE
This is normal.
The drum is turned off so that the steam
vapor remains in the drum. The drum will
normally turn for about 2 seconds once a
minute.
Drum does not turn
during STEAm CYCLE
This is normal.
Cannot see steam
vapor at the beginning
of cycle
Steam is released at different stages of
the cycle for each option.
This is normal.
Odors remain in
clothing after Steam
FreshTm
Steam FreshTm did not remove
odor completely.
Fabrics containing strong odors should be
washed in a normal cycle.
TROUBLESHOOTING 59
Error Codes
Problem
Possible Cause
Solutions
Error code: tE1 through
tE7
Temperature sensor failure.
Turn off the dryer and call for service.
Display shows error
code: PS (electric
dryers only)
Power cord is connected
incorrectly.
Check the connection of the power cord
to the terminal block.
*Flow SenseTm indicator Exhaust system is too long or
shows four bars during has too many turns/restrictions.
the drying cycle or the
Install a shorter or straighter duct run. See
the Installation Instructions for details.
Ductwork should be checked/cleaned
immediately. Dryer can be used in this
condition, but drying times will be longer
and energy consumption will increase.
display shows "d80"
Partial blockage of the ductwork
due to lint buildup or other
foreign object.
after drying
* This warning light
is not a dryer failure
and is not covered by
the dryer warranty.
Contact a duct cleaning
service to set up an
appointment to have
your exhaust system
cleaned and inspected.
If exhaust restrictions are sensed by the
Flow SenseTM system, the indicator will
remain on for 2 hours after the end of the
cycle. Opening the door or pressing the
POWER button will turn off the display.
The appliance has detected a
restriction in the external dryer
venting.
After clearing the restriction, the
Flow SenseTm system requires
multiple, consecutive cycles to
determine that the performance
value has improved before the
Flow SenseTm indicator is reset.
The Flow SenseTm
indicator remains
active after clearing
the restriction in the
venting.
If the Flow SenseTM indicator remains
active for more than five cycles after
the restriction has been cleared, call for
service.
Check steam feeder drawer:
(1) Make sure the steam feeder is filled
with water to the MAX line.
(2) Make sure the steam feeder is seated
properly and the drawer is fully closed.
(3) Turn the dryer off then restart the
STEAM CYCLE.
Water supply error.
indicator light is on
during the drying cycle
Do not use distilled water; the water level
sensor in the steam generator will not
work.
Pump not working. Unplug dryer and call
for service.
This display indicates that the steam
option has been set for a “big” item such
as a comforter.
The display shows
more Time button was pressed.
Press the Less Time button to reduce the
indicated load size.
Remove the lint from the filter before
every load. With the lint removed, hold
the filter up to a light to see if it is dirty
or clogged. If it looks dirty, follow the
cleaning instructions. With some loads
that produce high amounts of lint, it may
be necessary to clean the filter during the
cycle.
Lint filter not cleaned properly.
indicator light is on
during the drying cycle
60 TROUBLESHOOTING
Problem
Possible Cause
Solutions
Check steam feeder drawer:
(1) Make sure the steam feeder is filled
with water to the MAX line.
(2) Make sure the steam feeder is seated
properly and the drawer is fully closed.
Water supply error.
(3) Turn the dryer off then restart the
STEAM CYCLE.
indicator light is on
during the drying cycle
Do not use distilled water; the water level
sensor in the steam generator will not
work.
Pump not working.
Unplug dryer and call for service.
Do not use the dryer until the exhaust
system has been cleaned and/or repaired.
Using the dryer with a severely restricted
exhaust is dangerous and could result in
a fire or other property damage.
Check the outside dryer vent while the
dryer is operating to make sure there is
strong airflow.
The duct work is about 90%-95%
blocked.(“d90” or “d95” error
code is displayed for 2 hours
only)
The display shows d90,
d95
If the exhaust system is extremely long,
have it repaired or rerouted.
Keep the area around the dryer clean and
free of clutter.
house exhaust system blocked.
Check vent hood for damage or lint
clogging.
Make sure the area around the vent hood
is clear.
SMART DIAGNOSIS™ 61
SmART DIAgNOSIS™
Should you experience any problems with your dryer, it has the capability of transmitting data to your smart
phone using the LG Smart Laundry Application or via your telephone to the LG call center.
Smart Diagnosis™ cannot be activated unless your dryer is turned on by pressing the POWER button. If your
dryer is unable to turn on, then troubleshooting must be done without using Smart Diagnosis™.
Using Smart DiagnosisTm
Smart Diagnosis™ Through the Call
Center
Smart Diagnosis™ Using Your Smart
Call the LG call center at: (LG U.S.)
1
Phone
1-800-243-0000
(LG Canada) 1-888-542-2623.
Download the LG Smart Laundry & DW
application on your smart phone.
1
2
When instructed to do so by the call center
agent, hold the mouthpiece of your phone over
the Smart Diagnosis™ logo on the machine.
Hold the phone no more than one inch from (but
not touching) the machine.
2
Open the LG Smart Laundry application on your
smart phone. Press the right arrow button to
advance to the next screen.
Press the Record button on the smart phone and
then hold the mouth piece of the smart phone
near the Smart Diagnosis™ logo on the dryer.
3
NOTE
Do not touch any other buttons or icons on the
display screen.
With the phone held in place, press and hold the
Temp. Control button for 3 seconds.
4
5
Press and hold the Temp. Control button for 3
seconds.
3
4
Keep the phone in place until the tone
transmission has finished. The display will count
down the time.
Keep the phone in place until the tone
transmission has finished. The display will count
down the time.
When the recording is complete, view the
diagnosis by pressing the Next button on the
phone.
6
Once the countdown is over and the tones have
stopped, resume your conversation with the call
center agent, who will then be able to assist you
in using the information transmitted for analysis.
5
NOTE
Call quality differences by region may affect
the function.
•
NOTE
For best results, do not move the phone while
the tones are being transmitted.
•
Use a home telephone for better
communication performance, resulting in
better service.
•
•
If the call center agent is not able to get an
accurate recording of the data, you may be
asked to try again.
•
Poor call quality may result in poor data
transmission from your phone to the machine,
which could cause Smart DiagnosisTM to
malfunction.
62 WARRANTY (USA)
WARRANTY (USA)
Should your LG Dryer (“Product”) fail due to a defect in materials or workmanship under normal home use,
during the warranty period set forth below, LG will at its option repair or replace the product. This limited warranty
is valid only to the original retail purchaser of the product and applies only when purchased and used within the
United States including U.S. Territories. Proof of original retail purchase is required to obtain warranty service
under this limited warranty.
Warranty Period
Scope of Warranty
hOW SERVICE IS hANDLED
LG will provide parts and labor to repair or replace
defective parts.
One (1) year from date of
original retail purchase
Parts and Labor
Parts only. Customer will be responsible for any labor
or in-home service to replace defective parts.
Ten (10) years from date of
original retail purchase
Dryer drum
Replacement products and parts are warranted for the remaining portion of the original warranty period or
ninety (90) days, whichever is greater.
•
•
Replacement products and parts may be new or remanufactured.
ThIS WARRANTY IS IN LIEU OF ANY OThER WARRANTY, EXPRESS OR ImPLIED, INCLUDINg WIThOUT
LImITATION, ANY WARRANTY OF mERChANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO
ThE EXTENT ANY ImPLIED WARRANTY IS REQUIRED BY LAW, IT IS LImITED IN DURATION TO ThE
EXPRESS WARRANTY PERIOD ABOVE. NEIThER ThE mANUFACTURER NOR ITS U.S. DISTRIBUTOR
ShALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAmAgES OF ANY NATURE, INCLUDINg WIThOUT LImITATION, LOST REVENUES OR PROFITS, OR
ANY OThER DAmAgE WhEThER BASED IN CONTRACT, TORT, OR OThERWISE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how
long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you
specific legal rights and you may also have other rights that vary from state to state.
ThIS LImITED WARRANTY DOES NOT COVER:
Service trips to deliver, pick up, or install or repair the product; instruction to the customer on operation of
the product; repair or replacement of fuses or correction of wiring or plumbing, or correction of unauthorized
repairs/installation.
•
Failure of the product to perform during power failures and interruptions or inadequate electrical service.
•
•
Damage caused by leaky or broken water pipes, frozen water pipes, restricted drain lines, inadequate or
interrupted water supply or inadequate supply of air.
Damage resulting from operating the Product in a corrosive atmosphere or contrary to the instructions outlined
in the Product’s owner’s manual.
•
Damage to the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, or acts of God.
•
•
Damage or failure caused by unauthorized modification or alteration, or if it is used for other than the intended
purpose, or any water leakage where the unit was not properly installed.
Damage or failure caused by incorrect electrical current, voltage, or plumbing codes, commercial or industrial
use, or use of accessories, components, or consumable cleaning products that are not approved by LG.
•
•
Damage caused by transportation and handling, including scratches, dents, chips, and/or other damage to the
finish of your product, unless such damage results from defects in materials or workmanship and is reported
within one (1) week of delivery.
Damage or missing items to any display, open box, discounted, or refurbished Product.
•
•
Products with original serial numbers that have been removed, altered, or cannot be readily determined. Model
and Serial numbers, along with original retail sales receipt, are required for warranty validation.
Increases in utility costs and additional utility expenses.
•
•
Repairs when your Product is used in other than normal and usual household use (e.g. commercial use, in
offices and recreational facilities) or contrary to the instructions outlined in the Product’s owner’s manual.
WARRANTY (USA) 63
Costs associated with removal of your Product from your home for repairs.
•
•
The removal and reinstallation of the Product if it is installed in an inaccessible location or is not installed in
accordance with published installation instructions, including LG’s owner’s and installation manuals.
Damage resulting from misuse, abuse, improper installation, repair, or maintenance. Improper repair includes
use of parts not approved or specified by LG.
•
Filter is clogged.
Clean the lint filter.
•
Not heating, long dry
time
•
Duct is clogged.
Clean the hood and
duct.
•
•
Not heating, long dry
time
•
Excessive duct
length and/or multiple
elbows
Keep exhaust ducts
as short as possible,
using as few elbows
and bends as
Not heating, long dry
time
•
possible.
Reconnect power
cord, replace house
fuse or reset breaker.
If outlet is issue,
electrician may be
required.
•
Improperly connected
power cord or
electrical outlet issue.
No Power
•
•
Not Heating
gas valve is not
turned on. (gas Dryer)
Open the gas valve
•
•
Not heating
•
Instructions for door
reversal can be
found in the owner’s
manual.
Door Reversal
The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.
TO OBTAIN WARRANTY SERVICE AND ADDITIONAL INFORMATION
For assistance using this product or to schedule service, contact LG Electronics at 1-800-243-0000.
For further assistance, write: LG Electronics, 201 James Record Road, Huntsville, Alabama 35813
Memo
|