Jam message
Area name
Lexmark™ X560
Clearing Jams Guide
Jam at Scanner
7
ADF tray
Open ADF Cover R
and Remove Paper
Turn the Green Dial
to Remove Paper
Avoiding and clearing
jams
Clearing Tray 1 (MPT) jams
If the paper did not feed from the multipurpose feeder
correctly, Jam at Tray 1appears.
1 Pull the jammed paper out of the multipurpose feeder tray,
and then remove any remaining paper from the tray.
Avoiding jams
The following hints can help you avoid jams:
• Use only recommended paper or specialty media.
For more information, see the Card Stock & Label Guide
available on the Lexmark Web site at
• Do not load too much paper. Make sure the stack height does
not exceed the indicated maximum height.
Jam message
Area name
• Do not load wrinkled, creased, damp, or curled paper.
• Flex, fan, and straighten paper before loading it.
• Do not use paper that has been cut or trimmed by hand.
• Do not mix paper sizes, weights, or types in the same stack.
• Store the paper in an appropriate environment.
• Do not remove trays while the printer is printing.
• Push all trays in firmly after loading paper.
Jam at Exit
Open Door A
1
2
3
Fuser top
Jam at Reg. Roll
Open Door A
Fuser bottom
Jam at Duplexer
Open Door A
Optional duplex unit
• Make sure the guides in the trays are properly positioned, and
are not pressing too tightly against the paper.
Lift Belt Unit
Jam at Tray 3
Open Tray 3
Open Door A
4
5
6
Optional 550-sheet tray
(Tray 3)
• Make sure all printer cables are attached correctly. For more
information, see the setup documentation.
2 Push the release button, and gently lower the front door.
Jam at Tray 2
Open Tray 2
Open Door A
Standard tray (Tray 2)
CAUTION—HOT SURFACE: To reduce the risk of injury
from a hot component, allow the surface to cool before
touching it.
Understanding jam messages
and locations
Open doors and covers, and remove trays to access jam locations.
The illustration shows possible jam locations. To resolve any jam
message, you must clear all paper from the paper path.
Jam at Tray 1
Check Tray 1
Open Door A
Multipurpose Feeder (Tray 1)
1
5 Grasp the handle, and pull Tray 1 out. Remove the tray
completely.
6 Remove any jammed paper from inside the tray housing.
Clearing Tray 2 jams
If the paper did not feed from Tray 2 correctly, the jam is in the tray.
Jam at Tray 2appears.
1 Grasp the handle, and pull Tray 1 out. Remove the tray
completely.
7 Align the tray, and insert it.
3
2 Remove the jam. The jam could be in the tray or behind the
• Jams behind the tray area—Locate the jam on the
bottom surface of the tray housing. You may have to reach
far under the printer to locate the jam, as shown in the
following illustration. Pull the jam straight out.
tray area.
• Jams in the tray—Locate the single piece of paper lying
on top of the stack. Pull it straight out.
3 Align the tray, and insert it.
4 Push the release button, and gently lower the front door.
CAUTION—HOT SURFACE: To reduce the risk of injury
from a hot component, allow the surface to cool before
touching it.
4
• Jams in the tray—Locate the single piece of paper lying
on top of the stack. Pull it straight out.
5 Remove any jammed paper from inside the printer.
6 Close the front door.
Clearing Tray 3 jams
If the paper did not feed from Tray 3 correctly, the jam is in the tray.
Jam at Tray 3appears.
1 Grasp the handle, and pull Tray 3 out. Remove the tray
completely.
2 Remove the jam. The jam could be in the tray or behind the
tray area.
5
4 Push the release button, and gently lower the front door.
• Jams behind the tray area—Locate the jam on the
bottom surface of the tray housing. You may have to reach
far under the printer to locate the jam, as shown in the
following illustration. Pull the jam straight out.
5 Remove any jammed paper from inside the printer.
CAUTION—HOT SURFACE: To reduce the risk of injury
from a hot component, allow the surface to cool before
touching it.
3 Align the tray, and insert it.
6
CAUTION—HOT SURFACE: To reduce the risk of injury
from a hot component, allow the surface to cool before
touching it.
6 Close the front door.
2 Lift the fuser pressure release levers to release tension on the
paper.
1 Push the release button, and gently lower the front door.
Clearing jams in the fuser
If the paper is jammed in the fuser area, Jam at Exitor Jam
at Reg. Rollappears. A Jam at Reg. Rollmessage
indicates the paper is jammed below the fuser. A Jam at
Exitmessage indicates the paper is jammed above the fuser.
7
3 Lift the fuser cover, and then remove the jammed paper.
4 Close the fuser cover, and then lower the pressure release
levers.
5 Close the front door.
8
2 Pull out the jammed paper from the duplex unit. If jammed
paper cannot be found, go to the next step.
3 Lift the transfer belt unit.
Clearing jams in the duplex unit
If the paper did not feed through the duplex unit correctly, the jam
is in the duplex paper path. Jam at Duplexerappears.
CAUTION—HOT SURFACE: To reduce the risk of injury
from a hot component, allow the surface to cool before
touching it.
1 Push the release button, and gently lower the front door.
4 Remove any jammed paper from the duplex paper feeder.
9
5 Close the transfer belt unit.
6 Close the front door.
Clearing jams in the ADF
If the paper is jammed in the ADF, Jam at Scannerappears.
Remove all jammed paper, and make sure the paper feed tray is
not overfull.
1 Remove all paper from the paper feed tray, and then open the
ADF cover.
10
2 If the jam is in the paper feed area, remove the jam by carefully
pulling it up.
3 If the jam is at the paper exit area, turn the dial to remove the
jam.
4 Close the ADF cover.
5 Open the scanner cover and remove any jammed paper from
the paper feed area.
11
6 Close the scanner cover.
7 When all the jammed paper is removed, Return the
Removed Original and Press Startappears. Place
the original document in the ADF, and then press Start
to
continue with the scan job.
12
|