OWNER'S MANUAL
SIDE BY SIDE
REFRIGERATOR
Read this owner’s manual thoroughly before operating the
appliance and keep it handy for reference at all times.
ENGLISH
LRSDS2706*, LRSXS2706*, LRSOS2706*, LRSOC2306*, LRSXC2306*, LHSXS2706*,
LRSVS2706*
MFL71823901
Rev.06_021122
Copyright © 2021-2022 LG Electronics Inc. All Rights Reserved.
IMPORTANT SAFETY INSTRUCTIONS
3
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Safety Messages
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
follow all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages
will follow the safety alert symbol and either the word WARNING or CAUTION.
These words mean:
WARNING
You may be killed or seriously injured if you do not follow instructions.
CAUTION
You may be injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what may happen if the instructions are not followed.
WARNING
WARNING
• To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this
product, follow basic precautions, including the following:
Installation
• To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including
the use of long-sleeved gloves and safety glasses.
• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has
missing or broken parts, including a damaged cord or plug.
• Only connect this product to a dedicated grounded electrical outlet rated for use with this product (115
V, 60 Hz, AC only). It is the user’s responsibility to replace a standard 2-prong wall outlet with a standard
3-prong wall outlet.
• Do not use an outlet that can be turned off with a switch. Do not use an extension cord.
• The appliance must be positioned for easy access to a power source.
• When moving the refrigerator, be careful not to roll over or damage the power cord.
• Contact an authorized service center when installing or relocating the refrigerator.
• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
• Keep packing materials out of the reach of children. Packaging material can be dangerous for children.
There is a risk of suffocation.
• Do not install the refrigerator in a damp or dusty place where insulation on electrical parts may
deteriorate.
• Do not place the refrigerator in direct sunlight or expose it to the heat from heating appliances such as
stoves or heaters.
4
IMPORTANT SAFETY INSTRUCTIONS
• Do not bend or pinch the power cord excessively or place heavy objects on it.
Operation
• This appliance is intended to be used in household and similar applications such as:
- staff kitchen areas in shops, offices and other working environments;
- farm houses and by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments;
- catering and similar non-retail applications.
• This product is not to be used for special purposes such as the storage of medicine or test materials or
for use on ships, etc.
• DO NOT allow children to climb, stand, or hang on the refrigerator doors or on the shelves in the
refrigerator. They could damage the refrigerator and seriously injure themselves.
• Do not allow children to climb into the refrigerator. They could be trapped and suffocated.
• Children should be supervised to ensure that they do not play with the refrigerator.
• Keep fingers out of pinch point areas; clearances between the doors and cabinets are necessarily small.
Be careful closing doors when children are nearby.
• Do not touch frozen food or the metal parts in the freezer compartment with wet or damp hands. Doing
so may cause frostbite.
• Do not refreeze frozen food that has thawed completely. Doing so may result in a serious health hazard.
• Do not use an adapter plug or plug the power plug into a multi-outlet extension cord.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
• Do not operate the refrigerator or touch the power cord with wet hands.
• Do not modify or extend the power cord.
• Do not use an uncertified power outlet. Do not plug appliance into a damaged wall outlet.
• Do not put hands, feet or other objects into the air vents or bottom of the refrigerator. Doing so could
result in personal injury or electric shock.
• In the event of a gas leak (propane/LPG), ensure the area is adequately ventilated and contact an
authorized service center before resuming use. Do not touch the refrigerator or power cord of the
refrigerator.
• Disconnect the power cord immediately and contact an authorized service center if there is a strange
noise, odor, or smoke coming from the appliance.
• Do not use any fuse (such as copper, steel wire, etc.) other than a standard fuse.
• Do not place or use an electrical appliance inside the refrigerator, unless it is of a type recommended by
the manufacturer.
• Do not put animals inside the appliance.
• Do not place heavy or fragile objects, liquid filled containers, combustible substances, or flammable
objects (such as candles and lamps) on the appliance.
• If connected to a circuit protected by fuses, use time delay fuse.
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
• Do not use mechanical devices or other means to accelerate the defrosting process, other than those
recommended by the manufacturer.
• Do not use electrical appliances inside the food storage compartments of the appliance, unless they are
of the type recommended by the manufacturer.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
IMPORTANT SAFETY INSTRUCTIONS
5
Maintenance
• Do not use a hair dryer to dry the inside of the refrigerator.
• Do not light a candle to remove odors in the refrigerator.
• In the event of a refrigerant leak, move flammable objects away from the refrigerator. Ensure the area is
adequately ventilated and contact an authorized service center.
• Keep flammable materials and vapors, such as gasoline, away from the refrigerator.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
• Unplug the power plug before cleaning or repairing the refrigerator.
• The refrigerator and freezer compartment lights are interior LED lighting, and service should be
performed by a qualified technician.
• Unplug the power plug immediately in the event of a blackout or thunderstorm.
• Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.
• Do not store glass containers or soda in the freezer compartment. Contents may expand when frozen,
break the container and cause injury.
• Do not store, disassemble or repair the appliance yourself or allow unqualified personnel to do so.
Disposal
• Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days. When
disposing of the refrigerator, remove the packing materials from the door or take off the doors but leave
the shelves in place so that children may not easily climb inside.
• If disposing of a refrigerator, make sure the refrigerant and insulation foam are removed for proper
disposal by a qualified servicer. If you release the refrigerant or throw away the insulation foam, you
may be fined or imprisoned in accordance with the relevant environmental law. Insulation foam contains
flammable blowing gas.
• When discarding the appliance, remove the door gasket while leaving the shelves and bins in place, and
keep children away from the appliance.
Grounding Instructions
• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check
with a qualified electrician or service personnel if you are in doubt whether the appliance is properly
grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
• Have a certified electrician check the wall outlet and wiring for proper grounding.
• Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight
out from the outlet. Failure to do so may damage the power cord, resulting in a risk of fire and electric
shock.
6
IMPORTANT SAFETY INSTRUCTIONS
Risk of Fire and Flammable Materials
This appliance contains a small amount of isobutane refrigerant (R600a), which is combustible.
When transporting and installing the appliance, care should be taken to ensure that no parts
of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or
cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of
ignition and air out the room in which the appliance is standing for several minutes.
In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating
circuit occurs, the size of the room in which the appliance may be sited depends on the
amount of refrigerant used. The room must be 10.8 square feet (1 square meter) in size for
every 8g of R600a refrigerant inside the appliance. The amount of refrigerant in your
particular appliance is shown on the identification plate inside the appliance. Never start up an
appliance showing any signs of damage. If in doubt, consult your dealer.
CAUTION
CAUTION
• To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or
property when using this product, follow basic precautions, including the following:
Installation
• Do not install the refrigerator where there may be a danger of the unit falling.
• The refrigerator must be properly installed in accordance with the Installation Instructions.
Operation
• Do not use aerosols near the refrigerator.
• This appliance is intended to be used only in domestic and similar applications.
• Do not strike or apply excessive force to any glass surface. Do not touch glass surfaces if they are
cracked or broken.
• Do not overfill or pack items too tightly into door bins. Doing so may cause damage to the bin or
personal injury if items are removed with excessive force.
Maintenance
• Do not use strong detergents like wax or thinners for cleaning. Clean with a soft cloth.
• Remove foreign objects (such as dust and water) off the prongs of the power plug and contact areas. Do
not use a wet or damp cloth when cleaning the plug.
• Do not spray water directly on the inside or outside of the refrigerator.
• Do not clean glass shelves or covers with warm water when they are cold. They may break if exposed to
sudden temperature changes.
SAVE THESE INSTRUCTIONS
PRODUCT OVERVIEW
7
PRODUCT OVERVIEW
Product Features
The images in this guide may be different from the actual components and accessories, which are subject
to change by the manufacturer without prior notice for product improvement purposes.
Exterior
† This feature is only available on some models.
a Dispenser Control Panel
Sets the the dispenser mode.
b Filtered Water and Ice Dispenser
Dispenses purified water and ice.
c Door in Door
This is a convenient storage area for frequently-used items that require easy access.
d Door in Door Lever
Opens Door-in-Door.
e InstaView
Knock twice on the glass to turn the LED light inside the InstaView on or off.
PRODUCT OVERVIEW
9
InstaView Door-in-Door Model: LRSOS2706*, LRSOC2306*, LRSVS2706*
a LED Lamp
The LED lamps inside the appliance light up when you open the door.
b Temperature Sensor
This sensor senses the temperature of the fridge compartment.
• Maintain the distance between the sensor and food to accurately sense the temperature.
c Automatic Icemaker
This is where ice is automatically produced and stored.
d Craft Icemaker
This is where craft ice is automatically produced and stored.
e Freezer Shelf
Stores frozen food such as meat, fish, and ice cream.
• To freeze food items quickly, store the food on a shelf other than the top shelf. Food items will freeze
most quickly on any shelf except for the top shelf.
f Freezer Door Bin
Stores small packages of frozen food. Do not store ice cream or food which will be stored for a long
period of time.
g Freezer Drawer
Stores frozen food for longer storage.
h Fridge Shelf
Stores refrigerated foods and fresh foods.
• Store foods with higher moisture content at the front of the shelf.
• Adjust the shelf height by inserting the shelf in another groove at a different height.
• The actual number of shelves will differ from model to model.
i Fridge Door Bin
Stores small packages of refrigerated foods, drinks and sauce containers.
10 PRODUCT OVERVIEW
j Control Panel
Sets the refrigerator and freezer temperatures or other functions.
k Fridge Drawer
Stores fruits and vegetables to keep fresh for as long as possible.
l Bottom Drawer Cover
CAUTION
• Do not store any items at the front of the bottom shelf. The items may fall and cause an injury or
appliance damage.
m Door in Door Compartment
Stores commonly used food items such as beverages and snacks.
n InstaView
Knock twice on the glass to turn the LED light inside the InstaView on or off.
o Water Filter
Purifies water. Replace the water filter every six months. See the Replacing the Water Filter section in
this manual for details.
Product Specifications
The appearance and specifications listed in this manual may vary due to constant product improvements.
Electrical requirements: 115 V, 60 Hz
Min. / Max. water pressure: 20 - 120 psi (138 - 827 kPa)
Model
LRSDS2706*
LRSXS2706*
LRSOS2706*
LRSOC2306*
LRSXC2306*
LRSVS2706*
Description
Net weight
284 lb (129 kg)
265 lb (120 kg)
300 lb (136 kg)
276 lb (125 kg)
240 lb (109 kg)
302 lb (137 kg)
Standard-depth, Door-in-Door Side by Side Refrigerator, Craft Ice
Standard-depth, Side by Side Refrigerator
Standard-depth, Instaview Side by Side Refrigerator, Craft Ice
Standard-depth, Door-in-Door Side by Side Refrigerator, Craft Ice
Standard-depth, Side by Side Refrigerator
Standard-depth, Instaview Door-in-Door Side by Side Refrigerator,
Craft Ice
LHSXS2706*
Standard-depth, Side by Side Refrigerator, Craft Ice
278 lb (126 kg)
INSTALLATION 11
INSTALLATION
Before Installing
Installation Overview
Please read the following installation instructions first after purchasing this product or transporting it to
another location.
a Unpacking the Refrigerator
b Choosing the Proper Location
c Disassembling/Assembling
d Connecting the Water Line
e Leveling and Door Alignment
WARNING
• Connect to potable water supply only.
12 INSTALLATION
install a booster pump to compensate for the
low pressure.
Unpacking the Refrigerator
WARNING
• Use two or more people to move and install the
refrigerator. Failure to do so can result in back
injury or other injury.
Electricity
Use an individual, grounded outlet:115 Volts, 60
Hz, AC, 15 amps minimum.
• The refrigerator is heavy. Protect the floor when
moving the refrigerator for cleaning or service.
Always pull the refrigerator straight out when
moving it. Do not wiggle or walk the refrigerator
when trying to move it, as floor damage could
occur.
WARNING
• Do not overload house wiring and cause a fire
hazard by plugging in multiple appliances in the
same outlet with the refrigerator.
• Keep flammable materials and vapors, such as
gasoline, away from the refrigerator. Failure to
do so can result in fire, explosion, or death.
• To reduce the risk of electric shock, do not install
the refrigerator in a wet or damp area.
NOTE
Flooring
• Remove tape and any temporary labels from
your refrigerator before using. Do not remove
any warning labels, the model and serial number
label, or the Tech Sheet that is located under the
front of the refrigerator.
To avoid noise and vibration, the unit must be
installed and leveled on a solidly constructed floor.
If required, adjust the leveling legs to compensate
for the unevenness of the floor.
• To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue
residue can also be easily removed by rubbing a
small amount of liquid dish soap over the
adhesive with your fingers. Wipe with warm
water and dry.
NOTE
• Installing on carpeting, soft tile surfaces, a
platform or weakly supported structure is not
recommended.
• Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove
tape or glue. These products can damage the
surface of your refrigerator.
Ambient Temperature
Install this appliance in an area where the
temperature is between 55 °F (13 °C) and 110 °F
(43 °C).
• Reinstall or adjust shelves as needed.
Refrigerator shelves are installed in the shipping
position. Reinstall shelves according to your
individual storage needs.
If the temperature around the appliance is too low
or high, cooling ability may be adversely affected.
Choosing the Proper
Location
Water
The refrigerator must be located where a water
supply can be connected for the automatic
icemaker.
NOTE
• The water pressure must be 20 - 120 psi or 138 -
2
827 kPa or 1.4 - 8.4 kgf/cm . If the refrigerator is
installed in an area with low water pressure
2
(below 20 psi or 138 kPa or 1.4 kgf/cm ), you can
INSTALLATION 13
Dimensions and Clearances
• Check the dimensions of the appliance and the installation path to ensure there is sufficient room to
move the refrigerator through doors or narrow openings.
• If an opening is too narrow to fit the refrigerator through, remove the refrigerator doors. See Removing/
Assembling the Doors and Drawers in this manual.
• The installation location chosen for the refrigerator should allow space behind the unit for connections
and airflow and space in front to open the doors and drawers.
• Too small of a distance from adjacent items may result in lowered freezing capability and increased
electricity consumption charges. Allow at least 2 inches (50 mm) between the back of the refrigerator
and the wall.
• Remember to allow enough room in front of the refrigerator to fully open the doors and drawers.
B
E
A
F
G
D
C
LRSDS2706*,
LRSXS2706*,
LRSOS2706*,
LRSVS2706*,
LHSXS2706*
LRSOC2306*,
LRSXC2306*
-
Dimension/Clearance
A
B
C
D
E
Depth
Width
33 7/16" (850 mm)
35 7/8" (912 mm)
68 7/8" (1750 mm)
70 1/2" (1790 mm)
2" (50 mm)
28 15/16" (735 mm)
35 7/8" (912 mm)
68 7/8" (1750 mm)
70 1/2" (1790 mm)
2" (50 mm)
Height to Top of Case
Height to Top of Hinge
Back Clearance
F
Depth without Door
28 7/8" (735 mm)
51" (1295 mm)
24 3/8" (620 mm)
46 1/2" (1180 mm)
G
Depth (Total with Door Open 90°)
• Disconnect the electrical supply to the
refrigerator before installing.
Removing/Assembling
Doors
• Do not put hands, feet or other objects into the
air vents or bottom of the refrigerator.
If the entrance door is too narrow for the
refrigerator to pass through, remove the
refrigerator doors and move the refrigerator
sideways through the doorway.
• Be careful when handling the hinge and hinge
lever.
• Remove food and bins before detaching the
doors.
CAUTION
• Do not hold the handle when removing or
replacing the doors as the handle may come off.
• Use two or more people to remove and install
the refrigerator doors.
14 INSTALLATION
• Tools Needed
- Flat-head screwdriver
- Phillips screwdriver
Removing the Hinge Cover
Remove the screws from the hinge cover at the top
of the refrigerator. Lift the hook (not visible),
located at the bottom of the front side of the cover
with a flat-head screwdriver.
3
Pull out the water supply lines g. Disconnect
all the wire harnesses h. Unscrew the ground
wire i.
Removing the Freezer Door
1
The water supply is connected to the upper
right part of the rear surface of the
refrigerator. Remove the clip in the joint area.
Hold the water supply connection and gently
push the collet a to detach the water supply
line as shown.
NOTE
• The number of wire harnesses may vary
depending on the model.
• Ground wire is only present on some models.
4
Rotate the hinge lever j counterclockwise.
Lift the top hinge k free of the hinge lever
latch l.
NOTE
• Disassembling/Assembling the Water Lines
CAUTION
• When lifting the hinge free of the latch, be
careful that the door does not fall forward.
b Collet c Tube d Insert line e Clip
5
6
Free the hinge from the water lines and wire
harnesses and set it aside.
2
Remove the screws from the water line cover
f and detach the cover.
Lift the door from the bottom hinge pin m
and place it, inside facing up, on a non-
scratching surface.
INSTALLATION 15
4
Place the door, inside facing up, on a non-
scratching surface.
Removing the Refrigerator Door
1
Detach all the wire harnesses a. Unscrew the
ground wire b.
Assembling the Refrigerator Door
1
Place the door onto the bottom hinge pin a.
2
Rotate the hinge lever c clockwise. Lift the
top hinge d free of the hinge lever latch e.
2
Fit the hinge b over the hinge lever latch c
and slot it into place. Rotate the lever d
counterclockwise to secure the hinge.
CAUTION
• When lifting the hinge free of the latch, be
careful that the door does not fall forward.
NOTE
• Align the refrigerator door with the cabinet to
help fit the top hinge in place.
3
Lift the door from the bottom hinge pin f.
3
Connect all the wire harnesses e. Screw in
the ground wire f.
16 INSTALLATION
4
Push the water supply lines into the hole on
the top case and pull them through the
backplate.
NOTE
• The number of wire harnesses may vary
depending on the model.
• Ground wire is only present on some models.
Assembling the Freezer Door
1
Install the freezer door onto the bottom hinge
pin a.
NOTE
• The number of wire harnesses may vary
depending on the model.
• Ground wire is only present on some models.
5
Hold the water supply connection and gently
push in the collet e to connect the water
supply lines as shown. Insert the tube at least
5/8 inch (15 mm) into the connector. Insert
the clip on the joint to fasten the tubes in
place.
2
Fit the hinge b over the hinge lever latch c
and slot it into place. Rotate the lever d
clockwise and fasten the hinge.
NOTE
• Disassembling/Assembling the Water Lines
NOTE
• Align the freezer door with the cabinet to help fit
the top hinge in place.
3
Connect all the wire harnesses and the
ground wire.
f Collet g Tube h Insert line i Clip
INSTALLATION 17
• Gently press the collet and insert the tube until
only one line shows on the tube.
Water Pressure
You will need a cold water supply.
Water Pressure
• Models with water filter:
- 20 - 120 psi (138 - 827 kPa)
• Where reverse osmosis water filtration
system is connected to a cold water supply:
- 40 - 60 psi minimum to reverse osmosis
system (2.8 kgf/cm - 4.2 kgf/cm , or less than
2 - 3 seconds to fill a cup of 7 oz capacity)
Assembling the Hinge Cover
Position the hinge cover in its place. Insert and
tighten the cover screws.
2
2
If the water pressure from the reverse osmosis
2
system is less than 20 psi or 138 kPa or 1.4 kgf/cm
(takes more than 4 seconds to fill a cup of 7 oz or
198 cc capacity):
• Check to see if the sediment filter in the reverse
osmosis system is blocked. Replace the filter if
necessary.
• Allow the storage tank on the reverse osmosis
system to refill after heavy usage.
Connecting the Water Line
• If the water pressure remains low, call a
licensed, qualified plumber.
Before Beginning
• All installations must be in accordance with local
plumbing code requirements.
This water line installation is not covered by the
refrigerator warranty. Follow these instructions
carefully to minimize the risk of expensive water
damage.
Supplies Needed
If necessary, call a qualified plumber to correct
water hammer before installing the water supply
line to the refrigerator. Water banging in the pipes
(water hammer) in residential plumbing can cause
damage to refrigerator parts and lead to water
leakage or flooding.
• Copper or PEX Tubing, ¼ in. outer diameter, to
connect the refrigerator to the water supply. Be
sure both ends of the tubing are cut square. To
determine how much tubing you need, measure
the distance from the water valve on the back of
the refrigerator to the water supply pipe. Then,
add 8 feet (2.4 m). Be sure there is sufficient
extra tubing (about 8 feet [2.4 m] coiled into 3
turns of about 10 in. [25 cm] diameter) to allow
the refrigerator to move out from the wall after
installation.
• Turn the icemaker OFF if the refrigerator will be
used before the water line is connected.
• Do not install the icemaker tubing in areas
where the ambient temperatures fall below
freezing.
• Power drill.
WARNING
• ½ in. or adjustable wrench.
• Flat-blade and Phillips screwdrivers.
• Connect to potable water supply only.
• Two ¼ in. outer diameter compression nuts
and 2 ferrules (sleeves) to connect the copper
CAUTION
• To prevent burns and product damage, only
connect the refrigerator water line to a cold
water supply.
• Wear eye protection during installation to
prevent injury.
18 INSTALLATION
tubing to the shutoff valve and the refrigerator
water valve.
2
Choose the valve location.
• Choose a location for the valve that is easily
accessible. It is best to connect into the side
of a vertical water pipe. When it is necessary
to connect into a horizontal water pipe,
make the connection to the top or side,
rather than at the bottom, to avoid drawing
off any sediment from the water pipe.
• If your existing copper water line has a flared
fitting at the end, purchase an adapter (available
at plumbing supply stores) to connect the water
line to the refrigerator OR cut off the flared
fitting with a tube cutter and use a compression
fitting.
3
Drill the hole for the valve.
• Drill a ¼ in. hole in the water pipe using a
sharp bit. Remove any burrs resulting from
drilling the hole in the pipe. Be careful not
to allow water to drain into the drill. Failure
to drill a ¼ in. hole may result in reduced ice
production or smaller cubes.
• Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with
a minimum inside diameter of 5/32 in. at the
point of connection to the COLD WATER LINE.
Saddle-type shutoff valves are included in many
water supply kits. Before purchasing, make sure
a saddle-type valve complies with your local
plumbing codes.
NOTE
• The hookup line cannot be white, plastic tubing.
Licensed plumbers must use only copper tubing
(NDA tubing #49595 or #49599) or Cross Link
Polyethylene (PEX) tubing.
NOTE
• A self-piercing saddle type water valve should
not be used.
4
Fasten the shutoff valve.
• Fasten the shutoff valve to the cold water
pipe with the pipe clamp.
Water Line Installation Instructions
Install the shutoff valve on the nearest frequently
used drinking water line.
NOTE
• Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle
valves are illegal and use is not permitted in
Massachusetts. Consult with your licensed
plumber.
WARNING
• When using any electrical device (such as a
power drill) during installation, be sure the
device is battery-powered, double-insulated or
grounded in a manner that will prevent the
hazard of electric shock.
1
Shut off the main water supply.
• Turn on the nearest faucet to relieve the
pressure on the line.
INSTALLATION 19
diameter) to allow the refrigerator to move out
from the wall after installation.
7
Connect the tubing to the valve.
• Place the compression nut and ferrule
(sleeve) for copper tubing onto the end of
the tubing and connect it to the shutoff
valve. Make sure the tubing is fully inserted
into the valve. Tighten the compression nut
securely.
a Pipe Clamp
b Saddle-Type Shutoff Valve
c Vertical Cold Water Pipe
5
Tighten the pipe clamp.
• Tighten the clamp screws until the sealing
washer begins to swell.
NOTE
• Do not over tighten the clamp or you may crush
the tubing.
a Saddle-Type Shutoff Valve
b Compression Nut
c Packing Nut
d Outlet Valve
e Ferrule (sleeve)
8
Flush out the tubing.
• Turn the main water supply on and flush
out the tubing until the water is clear. Shut
the water off at the water valve after about
one quart of water has been flushed
through the tubing.
a Pipe Clamp
b Inlet End
c Clamp Screw
d Washer
6
Route the tubing.
• Route the tubing between the cold water
line and the refrigerator. Route the tubing
through a hole drilled in the wall or floor
(behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
9
Connect the tubing to the refrigerator.
NOTE
• Before making the connection to the
refrigerator, be sure that the refrigerator power
cord is not plugged into the wall outlet.
NOTE
• Remove the flexible plastic cap from the water
valve.
• Be sure there is sufficient extra tubing (about 8
ft. coiled into three turns of about 10 in.
• Place the compression nut and ferrule (sleeve)
onto the end of the tubing as shown.
20 INSTALLATION
doors do not close easily, adjust the refrigerator’s
tilt using the instructions below:
NOTE
• Insert the end of the copper tubing into the
connection as far as possible. While holding the
tubing, tighten the fitting.
1
Turn the leveling leg to the left to raise that
side of the refrigerator or to the right to lower
it. It may take several turns of the leveling leg
to adjust the tilt of the refrigerator.
a Tubing Clamp
b ¼ in. Tubing
NOTE
c ¼ in. Compression Nut
d Ferrule (sleeve)
• A flare nut wrench works best, but an open-end
wrench will suffice. Do not over-tighten.
e Refrigerator Connection
2
Open both doors and check to make sure that
they close easily. If the doors do not close
easily, tilt the refrigerator slightly more to the
rear by turning both leveling legs to the left. It
may take several more turns, and be sure to
turn both leveling legs the same amount.
10 Turn the water on at the shutoff valve.
• Tighten any connections that leak.
CAUTION
• Check to see if leaks occur at the water line
connections.
Door Alignment
Both the left and right refrigerator doors have an
adjustable nut, located on the bottom hinge, to
raise and lower them to align properly.
• Make sure the house water valve is fully open. If
it is not open completely, the icemaker and
dispenser may not work properly.
If the space between the doors is uneven, follow
the instructions below to align the doors evenly:
Use the wrench (included with the owner's
manual) to turn the nut in the door hinge to adjust
the height.
Leveling and Door
Alignment
Leveling
1
Open the door and use the wrench to loosen
the keeper nut by turning it to the left.
The refrigerator has two front leveling legs. Adjust
the legs to alter the tilt from front-to-back or side-
to side. If the refrigerator seems unsteady, or the
INSTALLATION 21
Start the Icemaker
• If the water line is connected, turn icemakers on.
- To turn icemakers on, refer to Control Panel in
the Operation section.
• The icemaker will not begin to operate until it
reaches its operating temperature of 15 °F (–9
°C) or below. It will then begin operation
automatically if the icemaker has been turned
ON.
2
3
Use the wrench to adjust the height by
turning the adjustment hinge pin to the right
to raise the door or to the left to lower it.
Use the wrench to fasten the keeper nut by
turning it to the right.
CAUTION
• Do not overtighten the door adjustment screw.
The hinge pin can be pulled out and the
adjustable range of height is a maximum of 2 in.
(5 cm).
Turning on the Power
• After installing, plug the refrigerator’s power
cord into a 3-prong grounded outlet and push
the refrigerator into the final position.
CAUTION
• Connect to a rated power outlet.
• Have a certified electrician check the wall outlet
and wiring for proper grounding.
• Do not damage or cut off the ground terminal of
the power plug.
Position the Refrigerator
• Arrange the coil of tubing so that it does not
vibrate against the back of the refrigerator or
against the wall. Push the refrigerator back to
the wall.
22 OPERATION
OPERATION
Before Use
Checklist
Clean the refrigerator.
Clean the refrigerator thoroughly and wipe off all dust that accumulated
during shipping.
CAUTION
• Do not scratch the refrigerator with a sharp object or use a detergent that
contains alcohol, a flammable liquid or an abrasive when removing any
tape or adhesive from the refrigerator. Remove adhesive residue by wiping
it off with your thumb or dish detergent.
• Do not peel off the model or serial number label or the technical
information on the rear surface of the refrigerator.
Open doors and drawers to ventilate the interior.
The inside of the refrigerator may smell like plastic at first. Remove any
adhesive tape from inside the refrigerator and open the refrigerator doors
and drawers for ventilation.
Connect the power supply.
Check if the power supply is connected before use.
Turn off the icemaker.
Turn off the icemaker if the refrigerator is not yet connected to the water
supply.
NOTE
• The icemaker water valve may buzz if the icemaker is turned on while the
refrigerator is not connected to the water supply.
Wait for the refrigerator to cool.
Allow the refrigerator to run for at least two to three hours before putting
food in it. Check the flow of cold air in the freezer compartment to ensure
proper cooling.
CAUTION
• Putting food in the refrigerator before it has cooled could cause the food to
spoil, or a bad odor to remain inside the refrigerator.
The refrigerator makes a loud noise after initial operation.
This is normal. The volume will decrease as the temperature decreases.
OPERATION 23
Control Panel
Depending on the model, some of the following functions may not be available.
The actual control panel may differ from model to model.
Control Panel Features
Refrigerator Control Panel
† This feature is only available on some models.
a Refrigerator
Indicates the set temperature of the refrigerator compartment in Celsius (°C) or Fahrenheit (°F). The
default refrigerator temperature is 37 °F (3 °C). Press the Refrigerator button repeatedly to select a
new set temperature from 33 °F to 43 °F (1 °C to 7 °C).
NOTE
• To change the temperature mode from °F to °C (or vice versa) press and hold the Refrigerator and
Freezer buttons simultaneously for approximately five seconds. The temperature indicator on the
display window switches between Celsius and Fahrenheit.
• The displayed temperature is the target temperature, and not the actual temperature of the refrigerator.
The actual refrigerator temperature depends on the food inside the refrigerator.
24 OPERATION
b Water Filter
Replace the water filter when the Replace Filter icon turns on. After replacing the water filter, press and
hold the Water Filter button for three seconds to turn the icon light off. Replace the water filter
approximately every six months.
c Freezer
Indicates the set temperature of the freezer compartment in Celsius (°C) or Fahrenheit (°F). The default
freezer temperature is 0 °F (-18 °C). Press the Freezer button repeatedly to select a new set
temperature from - 7 °F to 5 °F (-23 °C to -15 °C) or - 4 ℉ to 4 ℉.
d Self Care
UV light is used to keep the water outlet clean. UV clean function runs automatically for 10 minutes
every hour or can be manually activated at any time.
Press and hold this button for 3 seconds to activate it manually.
NOTE
• During operation, the function stops if the Water button is pressed. It resumes automatically after 1
hour.
• The function runs automatically for 10 minutes every hour without requiring you to press the Self Care
button.
• UVnano is a compound word derived from the words UV and its unit, a nanometer.
e Craft Ice
Press the Craft Ice button repeatedly to toggle between the 3 ICE, 6 ICE and OFF modes.
After 5 seconds of idle time, the last mode will be saved, and the display will return to normal.
• To turn off the Craft Ice maker, select the OFF mode.
• To turn on the Craft Ice maker, select the 3 ICE or 6 ICE mode.
NOTE
• For more ice, select the 6 ICE mode. For clearer ice, select the 3 ICE mode.
f Wi-Fi
The Wi-Fi button, when used with the LG ThinQ app, allows the refrigerator to connect to a home Wi-Fi
network. Refer to Smart Functions for information on the initial setup of the application.
The Wi-Fi indicator shows the status of the refrigerator's network connection. The indicator illuminates
when the refrigerator is connected to the Wi-Fi network.
Press and hold the Wi-Fi button for 3 seconds to connect to the network. The indicator blinks while the
connection is being made and then turns on once the connection is successfully made.
g Smart Grid
Press the Smart Grid button to turn the function On/Off. When the function is on, the indicator
illuminates. The function automatically turns on when the refrigerator is connected to the Wi-Fi
network. The Smart Grid function is only available if your electric utility company supports the function.
When the refrigerator is responding to a Demand Response (DR) message from the electric company,
the Grid On indicator illuminates.
h Ice Plus
This function increases both ice making and freezing capabilities.
• Press the Ice Plus button to illuminate the icon and activate the function for 24 hours. The function
automatically shuts off after 24 hours.
• Stop the function manually by pressing the button once more.
OPERATION 25
i Ice On/Off
Press and hold the Ice On/Off button for three seconds to turn the in-door icemaker on/off.
j Lock
The lock function disables every other button on the display.
• When power is initially connected to the refrigerator, the lock function is off.
• To lock the control panel buttons, press and hold the Lock button until the indicator appears in the
display and the function is activated.
• To disable the function, press and hold the Lock button for approximately three seconds.
NOTE
• Display Mode (For Store Use Only)
- The Display Mode disables all cooling in the refrigerator and freezer sections to conserve energy while
on display in a retail store. When activated, OFF is displayed on control panels with LCD displays. On
simplified control panels, the temperature indicators on the display will blink one row at a time from
top to bottom.
- To deactivate/activate:
With either refrigerator door opened, press the Ice Plus button 3 times consecutively while pressing
the Refrigerator button. The control panel beeps and the temperature settings display to confirm that
Display mode is deactivated. Use the same procedure to activate Display Mode.
Dispenser Control Panel
Water & Ice Type
Select the desired dispenser mode from the buttons on the dispenser control panel. From left to right, the
icons indicate cubed ice a, water b, and crushed ice c. Press the dispenser switch with a glass or other
container to dispense cubed ice, water or crushed ice.
NOTE
• When the refrigerator is in the Power Saving Mode, the display remains off until a door is opened or a
button is pressed. Once on, the display remains on for 20 seconds.
until all the temperature indicators in the
Sabbath Mode
refrigerator display turn on.
This feature is only available on some models.
• To turn Sabbath mode off manually, press and
hold the Freezer and Wi-Fi buttons for 3
Using the Sabbath Mode
Sabbath mode is used on the Jewish Sabbath and
Holidays.
seconds. For some models, press and hold the
Freezer and Refrigerator buttons for 3 seconds
until all the temperature indicators in the
refrigerator display turn off.
• To turn Sabbath mode on, touch the display to
activate it, then press and hold the Freezer and
Wi-Fi buttons for 3 seconds until sb appears in
the display. For some models, press and hold the
Freezer and Refrigerator buttons for 3 seconds
NOTE
• Sabbath mode automatically turns off after 96
hours.
26 OPERATION
• Dispense ice into a glass before filling it with
water or other beverages. Splashing may occur if
ice is dispensed into a glass that already
contains liquid.
NOTE
• Once turned on, Sabbath mode is maintained
even after a power outage.
• Some dripping may occur after dispensing. Hold
the cup beneath the dispenser for a few seconds
after dispensing to catch all of the drops.
• Selecting Sabbath mode automatically turns off
the alarm functions.
• The dispenser and InstaView are disabled in
Sabbath mode, on applicable models.
• Keep containers at an appropriate distance from
the dispensers. Tall, narrow glasses should be
held far enough from the ice outlet to prevent
ice from jamming in the ice chute. A container
with a very small opening should be held as
close to the dispenser as possible to avoid
spilling.
Ice and Water Dispenser
Before Using the Ice and Water
Dispenser
Using the Ice and Water Dispenser
CAUTION
• Keep children away from the dispenser. Children
may play with or damage the controls.
1
Press the icon for the desired dispenser mode
a. The LED over the selected icon turns on.
• Throw away the first bin full of ice (about 140-
160 cubes) after installation. The first ice and
water dispensed may include particles or odor
from the water supply line or the water tank.
This is also necessary if the refrigerator has not
been used for a long time.
• Dispense and throw away 2.5 gallons of water
(flush for approximately 5 minutes) after
installation. Do not dispense the entire 2.5 gallon
amount continuously. Press and release the
dispenser pad for cycles of 30 seconds ON and
60 seconds OFF. This is also necessary if the
refrigerator has not been used for a long time.
2
Press the dispenser paddle b with a glass or
other container to dispense cubed ice, water
or crushed ice.
• If ice or water dispenses unexpectedly, turn off
the water supply and contact an LG Electronics
Customer Information Center.
• Never use a glass that is exceptionally narrow or
deep. Ice may jam in the ice passage and
refrigerator performance may be affected.
• When dispensing ice from the dispenser, do not
use a fragile container.
Cleaning the Dispenser
• Do not hang on to or place heavy objects on the
refrigerator’s dispenser.
Cleaning the Ice and Water Outlet
Wipe the water outlet a or ice outlet b frequently
with a clean cloth as it may get dirty easily.
NOTE
• The dispenser will not operate when either of
the refrigerator doors is open.
• If discolored ice is dispensed, check the water
filter and water supply. If the problem continues,
contact an LG Electronics Customer Information
Center. Do not use the water or ice until the
problem is corrected.
OPERATION 27
• Never use thin crystal glasses or containers to
collect ice. Such containers may chip or break
resulting in glass fragments in the ice.
NOTE
• Lint from a cloth may adhere to the outlets.
• The UV clean function runs automatically for 10
minutes every hour to clean the dispenser
outlet. Press and hold the Self Care button for 3
seconds to manually activate it.
To prevent ice cubes from melting and leaking
from the dispenser, ALWAYS empty the ice bin
when the icemaker is turned OFF for more than a
few hours.
The ice passage may become blocked with frost if
only crushed ice is used. Remove the frost that
accumulates by removing the ice bin and clearing
the passage with a rubber spatula. Dispensing
cubed ice can also help prevent frost buildup.
Cleaning the Dispenser Tray
Wipe the entire area with a damp cloth. The
dispenser tray may become wet easily due to
spilled ice or water.
Detaching/Assembling the In-Door
Ice Bin
CAUTION
• Only qualified service personnel from an LG
Electronics service center should disassemble or
repair the icemaker.
• When handling the ice bin, keep hands away
from the icemaker tray area to avoid personal
injury.
Locking the Ice and Water
Dispenser
Press and hold the Lock button for three seconds
to lock the dispenser and all the control panel
functions. Follow the same instructions to unlock.
• Avoid touching the auto shutoff (feeler arm)
when replacing the ice bin.
In-Door Ice Bin
Before Using the In-Door Ice Bin
The icemaker stops producing ice when the in-
door ice bin is full. To make room for additional ice,
empty the ice bin into another location in the
freezer compartment. During use, the ice may
stack unevenly in the bin, causing the icemaker to
misread the number of ice cubes and stop
producing ice. Shaking the ice bin to level the ice
within it can reduce this problem.
CAUTION
1
To detach, lift the ice storage bin slightly and
pull it out as shown in the figure.
• Keep hands and tools out of the in-door ice bin
and dispenser chute. Failure to do so may result
in damage or personal injury.
• When handling the ice bin, keep hands away
from the icemaker tray area to avoid personal
injury.
• Storing cans or other items in the ice bin will
damage the icemaker.
28 OPERATION
• It takes about 12 to 24 hours for a newly
installed refrigerator to begin making ice.
• Ice-making stops when the in-door ice bin is full.
When full, the in-door ice bin holds
approximately 6 to 8 (12-16 oz.) glasses of ice.
• Foreign substances or frost on the ice-detecting
sensor can interrupt ice production. Make sure
the sensor area is clean at all times for proper
operation.
• To increase ice production, use the Ice Plus
function. The function increases both ice making
and freezing capabilities.
NOTE
• Use both hands to remove the ice bin to avoid
dropping it.
In-Door Icemaker
2
To assemble, carefully insert the in-door ice
bin, slanting the top slightly to fit it under the
icemaker.
a Auto Shutoff (feeler arm)
Before Using the Freezer Icemaker
This feature is only available on some models.
The feature may vary depending on model
purchased.
NOTE
• Throw away the first bin full of ice after
installation. This is also necessary if the
refrigerator has not been used for a long time.
Automatic Icemaker
• The icemaker begins producing ice
approximately 48 hours after the appliance is
initially installed.
WARNING
• DO NOT place fingers in the automatic icemaker
when the refrigerator is plugged in.
• The sound of ice dropping into the ice bin is
normal.
• Avoid contact with any moving parts of the
ejector mechanism or with the heater that
releases the ice cubes.
• If the ice bin is completely filled with ice, ice
production will stop.
• The amount and shape of ice may vary according
to the environment (ambient temperature
around the appliance, frequency of the door
being opened, amount of food stored in the
appliance, water pressure, etc.).
Before Using the In-Door Icemaker
NOTE
• In the event of a power outage, throw away the
ice stored in the ice bin.
• Ice is made in the automatic in-door icemaker
and sent to the dispenser. The icemaker
produces 70 - 182 cubes in a 24-hour period,
depending on freezer compartment
temperature, room temperature, number of
door openings and other operating conditions.
OPERATION 29
• The ice bin stores 20 - 30 pieces of round ice.
TM
Freezer Icemaker (Craft Ice
)
This feature is only available on some models.
Turning the Icemaker On/Off
To turn icemakers On/Off, refer to Control Panel in
the Operation section.
Normal Sounds You May Hear
• Keeping the power turned on to the icemaker
before the water line is connected can damage
the icemaker.
a Feeler Arm
• You will hear the sound of ice dropping into the
bin and water running in the pipes as the
icemaker refills.
CAUTION
• Do not insert round ice into the in-door ice bin,
as it can damage the ice and water dispenser.
• The icemaker water valve buzzes as the
icemakers fill with water. If the icemakers are
turned on, they will buzz even if they have not
yet been hooked up to water.
NOTE
To stop the buzzing:
• The icemaker begins producing ice
approximately 48 hours after the appliance is
initially installed. The first batches of ice may not
be round and clear.
- Turn icemakers off by refering to Control Panel
in the Operation section.
• Following installation or water filter
replacement, the first few batches of ice may be
semicircular or contain air bubbles.
Preparing for Vacation
Turn icemakers off and shut off the water supply
to the refrigerator.
• If the water pressure is less than 20 psi (138 kPa)
or a reverse osmosis system is used, the shape
of the ice may vary.
To turn the icemakers off, refer to Control Panel in
the Operation section.
• The ice may look cloudy depending on the water
quality in the installation location and the
operating conditions.
NOTE
• The ice bin should be emptied any time
icemakers are turned Off.
• Throw away any shards of ice you may find in the
ice bin, as they may stick to the ice stored in the
ice bin.
If the ambient temperature will drop below
freezing, have a qualified technician drain the
water supply system to prevent serious property
damage due to flooding caused by ruptured water
lines or connections.
• After a short term power outage, it will take
longer to make the first batch of ice, and the ice
may not be round. If the power will be out for a
longer period, throw away the ice stored in the
ice bin.
• The Craft Ice icemaker produces 1 batch of
round ice (3 pieces) at a time.
Storing Food
• In 3 ICE mode, the Craft Ice icemaker produces
1 batch of round ice (3 pieces) about every 24
hours. In 6 ICE mode, the Craft Ice icemaker
produces 2 batches of round ice (6 pieces total)
in the same period.
NOTE
• If you are leaving home for a short period, like a
short vacation, the refrigerator should be left on.
Refrigerated foods that are able to be frozen will
stay preserved longer if stored in the freezer.
• For more ice, select the 6 ICE mode. For clearer
ice, select the 3 ICE mode.
• The time needed to make ice may vary according
to operating conditions.
30 OPERATION
• If you are leaving the refrigerator turned off for
an extended period, remove all food and unplug
the power cord. Clean the interior, and leave the
door open to prevent fungi from growing in the
refrigerator.
• Vegetables with skins (carrots, peppers)
- Place in plastic bags or plastic container and
store in crisper.
• Fish
- Freeze fresh fish and shellfish if they are not
being eaten the same day purchased. Eating
fresh fish and shellfish the same day
purchased is recommended.
• If doors are opened or closed too often, warm
air may penetrate the refrigerator and raise its
temperature. This can increase the running costs
of the unit.
• Leftovers
- Cover leftovers with plastic wrap or aluminum
foil, or store in plastic containers with tight
lids.
Food Storage Tips
Wrap or store food in the refrigerator in airtight
and moisture-proof material unless otherwise
noted. This prevents food odor and taste transfer
throughout the refrigerator. For dated products,
check date code to ensure freshness.
NOTE
• Do not store food with high moisture content
towards the top of the refrigerator. The moisture
could come into direct contact with the cold air
and freeze.
CAUTION
• Do not overfill or pack items too tightly into door
bins. Doing so may cause damage to the bin or
personal injury if items are removed with
excessive force.
• Wash food before storing it in the refrigerator.
Vegetables should be washed, and food
packaging should be wiped down to prevent
adjacent foods from being contaminated.
• Do not store glass containers in the freezer.
Contents may expand when frozen, break the
container and cause injury.
• If the refrigerator is kept in a hot and humid
place, frequent opening of the door or storing a
lot of vegetables in the refrigerator may cause
condensation to form. Wipe off the
condensation with a clean cloth or a paper towel.
How to Store Food
• Butter or Margarine
- Keep opened butter in covered dish or closed
compartment. When storing an extra supply,
wrap in freezer packaging and freeze.
Storing Frozen Food
Check a freezer guide or a reliable cookbook for
further information about preparing food for
freezing or food storage times.
• Cheese
- Store in original wrapping until used. Once
opened, rewrap tightly in plastic wrap or
aluminum foil.
Freezing
Your freezer will not quick-freeze a large quantity
of food. Do not put more unfrozen food into the
freezer than will freeze within 24 hours (no more
than 2 to 3 pounds of food per cubic foot of freezer
space). Leave enough space in the freezer for air to
circulate around packages. Be careful to leave
enough room at the front so the door can close
tightly.
• Milk
- Wipe milk cartons. For coldest milk, place
containers on an interior shelf.
• Eggs
- Store in original carton on interior shelf, not on
door shelf.
• Fruit
Storage times will vary according to the quality
and type of food, the type of packaging or wrap
used (how airtight and moisture-proof) and the
storage temperature. Ice crystals inside a sealed
package are normal. This simply means that
moisture in the food and air inside the package
have condensed, creating ice crystals.
- Do not wash or hull fruit until it is ready to be
used. Sort and keep fruit in original container
in a crisper, or store in completely closed
paper bag on refrigerator shelf.
• Leafy Vegetables
- Remove store wrapping, trim or tear off
bruised and discolored areas, wash in cold
water, and drain. Place in plastic bag or plastic
container and store in crisper.
OPERATION 31
2
To assemble drawers, slightly tilt up the front,
insert into the frame and push back into
place.
NOTE
• Allow hot foods to cool at room temperature for
30 minutes, and then package and freeze.
Cooling hot foods before freezing saves energy.
CAUTION
• Use both hands to remove and assemble
drawers. The compartment is heavy when filled
with food and may cause injury if dropped.
Packaging
Successful freezing depends on correct packaging.
When you close and seal the package, it must not
allow air or moisture in or out. If it does, you could
have food odor and taste transfer throughout the
refrigerator and could also dry out frozen food.
• Open refrigerator doors fully when removing or
assembling drawers.
• You will see the water tank while removing the
Fresh Zone drawer. Do not remove the water
tank or water leakage may occur. The water tank
is not a removable part.
Packaging Recommendations
• Rigid plastic containers with tight-fitting lids
• Straight-sided canning/freezing jars
• Heavy-duty aluminum foil
• Plastic-coated paper
• Non-permeable plastic wraps
• Specified freezer-grade self-sealing plastic bags
Follow package or container instructions for
proper freezing methods.
Do not use
• Bread wrappers
a Water tank (Type A)
• Non-polyethylene plastic containers
• Containers without tight lids
• Wax paper or wax-coated freezer wrap
• Thin, semi-permeable wrap
b Water tank (Type B)
Refrigerator Shelves
The shelves in the refrigerator are adjustable to
meet individual storage needs.
Drawers
Adjusting the shelves to fit items of different
heights will make finding the exact item you want
easier.
Removing/Assembling Drawers
1
To remove drawers, pull them out to full
extension, lift the front, and pull straight out.
Detaching/Assembling Shelves
CAUTION
• Do not clean glass shelves with warm water
while they are cold. Shelves may break if
exposed to sudden temperature changes or
impact.
1
Use safety gloves. To disassemble, remove all
items from the shelf. Supporting the shelf
from underneath, lift the back of the shelf and
slide the shelf forward slightly to disengage
the back stop a.
NOTE
• When removing or installing the drawer, lift the
cover to help remove or insert the drawer.
32 OPERATION
4
To assemble, tilt one side of the shelf up and
align the shelf with the shelf guides at the
desired height. The back stop on the shelf
should be facing down. Slide the shelf in until
the back stop falls into place.
CAUTION
• Make sure that shelves are level from one side to
the other. Failure to do so may result in the shelf
falling or spilled food.
2
Tilt one side of the shelf up slightly.
InstaView
This feature is only available on some models.
InstaView Door-in-Door
Knock twice on the glass to turn the LED light
inside the InstaView on or off. The LED light turns
off automatically after 10 seconds.
3
Make sure the door is open as far as possible
before pulling the shelf forward to remove it.
If needed, have an assistant to fully open the
door while you pull out the shelf.
NOTE
• The LED light does not turn on if either door is
open.
• The InstaView function will not activate for two
seconds after closing the door.
CAUTION
• Be careful not to damage the door with the shelf.
• The InstaView function is disabled when the ice
dispenser is in use.
Door-in-Door
This feature is only available on some models.
The Door-in-Door compartment allows for easy
access to commonly used food items.
OPERATION 33
Door-in-Door Compartment
To access the Door-in-Door compartment, pull the
lever at the bottom of the door upwards until the
Door-in-Door opens.
Door Bins
Detaching/Assembling Door Bins
The door bins are removable for easy cleaning and
adjustment.
1
To remove the bin, simply lift the bin up and
pull straight out.
2
To assemble the bin, slide it in above the
desired support and push down until it snaps
into place.
CAUTION
• Regularly detach and wash the storage bins and
shelves; they can become easily contaminated
by food.
• Do not apply excessive force while detaching or
assembling the storage bins.
• Do not use the dishwasher to clean the storage
bins and shelves.
34 SMART FUNCTIONS
SMART FUNCTIONS
Before Using LG ThinQ Application
LG ThinQ Application
This feature is only available on models with Wi-Fi.
1
2
3
Use a smartphone to check the strength of
the wireless router (Wi-Fi network) near the
appliance.
The LG ThinQ application allows you to
communicate with the appliance using a
smartphone.
• If the distance between the appliance and
the wireless router is too far, the signal
becomes weak. It may take a long time to
register or fail to install the application.
LG ThinQ Application Features
• Smart Learner
- Provides a more personalized experience
based on an analysis of your usage patterns.
Turn off the Mobile data or Cellular Data on
your smartphone.
• Smart Sabbath
- Activates or deactivates the Sabbath mode and
sets the schedule for the mode activation.
• Energy Monitoring
- This feature keeps track of the refrigerator’s
power consumption and the number of door
openings.
Connect your smartphone to the wireless
router.
• Remote Control
- Controls the refrigerator temperature, air filter
and Ice Plus from the smartphone app.
• Push Messages
- If the door remains open for more than ten
minutes, you will receive a push message.
When Ice Plus is finished, you will receive a
push message.
NOTE
• To verify the Wi-Fi connection, check that the Wi-
Fi indicator on the control panel is lit.
TM
• Smart Diagnosis
- This function provides useful information for
diagnosing and solving issues with the
appliance based on the pattern of use.
• The appliance supports 2.4 GHz Wi-Fi networks
only. To check your network frequency, contact
your Internet service provider or refer to your
wireless router manual.
• Settings
• LG ThinQ is not responsible for any network
connection problems or any faults, malfunctions,
or errors caused by network connection.
- Allows you to set various options on the
refrigerator and in the application.
† This feature is only available on some models.
• The surrounding wireless environment can
make the wireless network service run slowly.
• If the appliance is having trouble connecting to
the Wi-Fi network, it may be too far from the
router. Purchase a Wi-Fi repeater (range
NOTE
• If you change your wireless router, Internet
service provider, or password, delete the
registered appliance from the LG ThinQ
application and register it again.
extender) to improve the Wi-Fi signal strength.
• The network connection may not work properly
depending on the Internet service provider.
• This information is current at the time of
publication. The application is subject to change
for product improvement purposes without
notice to users.
• The Wi-Fi may not connect or the connection
may be interrupted because of the home
network environment.
• If the appliance cannot be registered due to
problems with the wireless signal transmission,
SMART FUNCTIONS 35
unplug the appliance and wait about a minute
before trying again.
Output Power < 30 dBm
(Max)
• If the firewall on your wireless router is enabled,
disable the firewall or add an exception to it.
• The wireless network name (SSID) should be a
combination of English letters and numbers. (Do
not use special characters.)
FCC Notice
The following notice covers the transmitter
module contained in this product.
• Smartphone user interface (UI) may vary
depending on the mobile operating system (OS)
and the manufacturer.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
• If the security protocol of the router is set to
WEP, network setup may fail. Change the
security protocol (WPA2 is recommended), and
register the product again.
Installing the LG ThinQ Application
Search for the LG ThinQ application from the
Google Play Store or Apple App Store on a
smartphone. Follow instructions to download and
install the application.
• Reorient or relocate the receiving antenna.
Connecting to Wi-Fi
• Increase the separation between the equipment
and the receiver.
The Wi-Fi button, when used with the LG ThinQ
application, allows the appliance to connect to a
home Wi-Fi network. The Wi-Fi indicator shows the
status of the appliance’s network connection. The
Wi-Fi indicator illuminates when the appliance is
connected to the Wi-Fi network.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
• Initial Appliance Registration
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two
conditions:
Run the LG ThinQ application and follow the
instructions in the application to register the
appliance.
(1) This device may not cause harmful interference
and
• Re-registering the Appliance or Registering
Another User
Press and hold the Wi-Fi button for 3 seconds to
temporarily turn it off. Run the LG ThinQ
application and follow the instructions in the
application to register the appliance.
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.
NOTE
• To disable the Wi-Fi function, press and hold the
Wi-Fi button for 3 seconds. The Wi-Fi indicator
will be turned off.
FCC RF Radiation Exposure
Statement
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-
located or operating in conjunction with any other
antenna or transmitter.
Wireless LAN Module Specifications
Frequency
Range
2412 - 2462 MHz
36 SMART FUNCTIONS
This equipment should be installed and operated
with a minimum distance of 20 cm (7.8 inches)
between the antenna and your body. Users must
follow the specific operating instructions for
satisfying RF exposure compliance.
Smart Grid Function
When the refrigerator operates in Smart Grid
mode, the Smart Refrigerator function can control
energy usage or delay the operation of some
functions to save energy during peak usage
periods.
• You can override the Smart Grid function any
time (using the Smart Grid button or
application).
Industry Canada Statement
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the
following two conditions:
• To use the Smart Grid function, you need to
register your application with your electric utility
company, provided that your electric utility
company supports the function. In other words,
the Smart Grid function will not be available if
your electric utility company does not support
the function or does not have the capability to
support the function.
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
Smart Grid Application Features
• Smart Saving_Demand Response
IC Radiation Exposure Statement
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment.
- You can lower energy usage based on Demand
Response (DR) signals from the utility
company. If the refrigerator is operating in
Smart Saving mode according to the DR signal,
you can see a pop up.
This equipment should be installed and operated
with a minimum distance of 20 cm (7.8 inches)
between the antenna and your body.
• Seasonal Energy Savings
- Lower energy usage based on time period.
NOTE
• THE MANUFACTURER IS NOT RESPONSIBLE FOR
ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD
VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
Using the Smart Grid Function
This feature responds to notification events from
your utility company to run high energy
consuming tasks during off-peak periods when
demand is lower. These notification events are
known as Demand Response signals.
If the refrigerator receives a Demand Response
signal from the utility company, the refrigerator
will turn on the Grid LED on the refrigerator
display and control its power consumption
according to the signal. The refrigerator will
respond to the signals received from the utility
company as long as product performance is
maintained.
Open Source Software Notice
Information
To obtain the source code under GPL, LGPL, MPL,
and other open source licenses that have the
obligations to disclose source code, that is
contained in this product, and to access all
referred license terms, copyright notices and other
relevant documents please visit https://
opensource.lge.com.
If the refrigerator receives a Demand Response
signal, the refrigerator will operate in Delay
Appliance Load (DAL) or Temporary Appliance
Load Reduction (TALR) mode.
LG Electronics will also provide open source code
to you on CD-ROM for a charge covering the cost
of performing such distribution (such as the cost of
media, shipping, and handling) upon email
request to [email protected].
Delay Appliance Load (DAL)
The refrigerator responds to a DAL signal by
providing a moderate load reduction for the
duration of the delay period.
This offer is valid to anyone in receipt of this
information for a period of three years after our
last shipment of this product.
SMART FUNCTIONS 37
This mode controls functions that consume a lot of
energy such as adjusting the cooling system,
running the defrost cycle, and making ice.
• Energy Monitoring
- Get door open event
- Get energy consumption
• When the refrigerator operates in DAL mode,
the Grid LED is illuminated on the refrigerator
display.
• Delay Defrost Capability
- Insert a delay defrost schedule event
- Update a delay defrost schedule event
- Delete a delay defrost schedule event
- Get the delay defrost schedule
• DAL mode is automatically deactivated after the
period stipulated by the DAL signal (max. 4
hours) or when you override the Smart Grid
function.
Temporary Appliance Load Reduction
(TALR)
The refrigerator responds to a TALR signal by
aggressively reducing the load for a short time
period, typically 10 minutes. This mode reduces
energy consumption by stopping the compressor
and controlling the functions that consume a lot of
energy such as the defrost cycle and fan.
TM
Smart Diagnosis Feature
This feature is only available on models with the c
or d logo.
Use this feature to help you diagnose and solve
problems with your appliance.
• When the refrigerator operates in TALR mode,
the Grid LED is illuminated on the refrigerator
display.
NOTE
• For reasons not attributable to LGE’s negligence,
the service may not operate due to external
factors such as, but not limited to, Wi-Fi
unavailability, Wi-Fi disconnection, local app
store policy, or app unavailability.
• TALR mode is automatically deactivated after the
received duration (max. 10 minutes), or when
you override the Smart Grid function. The mode
is immediately deactivated and the refrigerator
returns to its normal state when the door is
opened or closed, or the dispenser is used.
• The feature may be subject to change without
prior notice and may have a different form
depending on where you are located.
Override Smart Grid Mode
To ignore the Demand Response signal from the
utility company and override the Smart Grid
function, push the Smart Grid button while the
refrigerator is in Smart Grid mode.
Using LG ThinQ to Diagnose Issues
If you experience a problem with your Wi-Fi
equipped appliance, it can transmit
troubleshooting data to a smartphone using the
LG ThinQ application.
When you override the Smart Grid function, the
refrigerator ignores the Demand Response signal
and is no longer controlled by the utility company
until the next Demand Response signal is sent. You
can also override the Smart Grid function using the
smart phone app.
• Launch the LG ThinQ application and select the
Smart Diagnosis feature in the menu. Follow
the instructions provided in the LG ThinQ
application.
LG Open API
You can manage Smart Grid features for the LG
Smart Refrigerator.
Using Audible Diagnosis to
Diagnose Issues
Follow the instructions below to use the audible
diagnosis method.
Please check the detailed specifications on the
notice page on us.smartthinq.com.
• Launch the LG ThinQ application and select the
Smart Diagnosis feature in the menu. Follow
the instructions for audible diagnosis provided
in the LG ThinQ application.
API List
• Demand Response
- Send demand response signal
• Power Saving
1
Open the right refrigerator door.
- Set saving mode
- Get schedule of DR/Delay Defrost
38 SMART FUNCTIONS
2
Hold the Lock button for three seconds.
• If the display has been locked for over five
minutes, you must deactivate the lock and
then reactivate it.
3
Hold the mouthpiece of your phone in front of
the speaker that is located on the right hinge
of the refrigerator door.
4
Press and hold the Freezer button for three
seconds while continuing to hold your phone
to the speaker.
5
6
After you hear three beeps, release the
Freezer button.
Keep the phone in place until the tone
transmission has finished. The display will
count down the time. Once the countdown is
over and the tones have stopped, the
diagnosis will be displayed in the application.
NOTE
• For best results, do not move the phone while
the tones are being transmitted.
MAINTENANCE 39
MAINTENANCE
To help remove odors, wash the inside of the
Cleaning
refrigerator with a mixture of baking soda and
warm water. Mix 2 tablespoons of baking soda to 1
quart of water (26 g soda to 1 liter water.) Be sure
the baking soda is completely dissolved so it does
not scratch the surfaces of the refrigerator.
WARNING
• Use non-flammable cleaner. Failure to do so can
result in fire, explosion, or death.
CAUTION
Door Liners and Gaskets
• Do not use an abrasive cloth or sponge when
cleaning the interior and exterior of the
refrigerator.
Use a clean sponge or soft cloth and a mild
detergent in warm water. Do not use cleaning
waxes, concentrated detergents, bleaches, or
cleaners containing petroleum on plastic
refrigerator parts.
• Do not place your hand on the bottom surface of
the refrigerator when opening and closing the
doors.
Plastic Parts (Covers and Panels)
General Cleaning Tips
• Both the refrigerator and freezer sections
defrost automatically; however, clean both
sections once a month to prevent odors.
Use a clean sponge or soft cloth and a mild
detergent in warm water. Do not use glass
cleaners, abrasive cleansers, or flammable fluids.
These can scratch or damage the material.
• Wipe up spills immediately.
• Unplug the refrigerator or disconnect power
before cleaning.
Condenser Coils
Use a vacuum cleaner with a brush or crevice
attachment to clean the condenser cover and
vents. Do not remove the panel covering the
condenser coil area.
• Remove all removable parts, such as shelves.
• Use a clean sponge or soft cloth and a mild
detergent in warm water. Do not use abrasive or
harsh cleaners.
• Hand wash, rinse and dry all surfaces
thoroughly.
Exterior
For products with black stainless steel exterior,
spray glass cleaner on a clean microfiber cloth and
rub in direction of grain. Do not spray glass
cleaner directly at the display panel. Do not use
harsh or abrasive cleaners.
For products with a standard stainless steel
exterior, use a damp microfiber cloth and rub in
the direction of the grain. Dry with a paper towel
to avoid streaks. For stubborn stains and
fingerprints, use a few drops of liquid dish soap in
water, and rinse with hot water before drying. Do
not use abrasive or harsh cleaners.
Air Filter
Reusing the Air Filter
You can remove the odors absorbed by the air
filter and reuse the filter.
1
To remove the air filter, pull out the upper
fridge drawer.
Inside Walls
• Allow freezer to warm up so the cloth will not
stick.
40 MAINTENANCE
Water Filter
Before Replacing the Water Filter
WARNING
• To reduce the risk associated with choking, do
not allow children under 3 years of age to have
access to small parts during the installation of
this product.
• To reduce the risk associated with the ingestion
of contaminants, do not use with water that is
microbiologically unsafe or of unknown quality
without adequate disinfection before or after the
system. Systems certified for cyst reduction may
be used on disinfected water that may contain
filterable cysts.
2
3
Unscrew the screw at the air filter.
• Use of unauthorized water filters may result in
product malfunction, water leakage or water
quality issues, which will not be covered under
the product warranty.
Press on the hooks at the air filter and then
take it out.
CAUTION
• Read and follow Use Instructions before
installation and use of this system.
• Installation and use MUST comply with all state
and local plumbing codes.
• Do not install if water pressure exceeds 120 psi
(827 kPa). If your water pressure exceeds 80 psi,
you must install a pressure limiting valve.
Contact a plumber if uncertain how to check
your water pressure.
4
Leave the filter in the sun to dry or use a hair
dryer.
• Do not install where water hammer conditions
may occur. If water hammer conditions exist you
must install a water hammer arrester. Contact a
plumbing professional if you are uncertain how
to check for this condition.
• To increase deodorizing performance, a
natural palm wood material is attached to
the filter. If residue falls off, it will not harm
you and can be wiped off easily with a towel
or cloth.
• Do not install on hot water supply lines. The
maximum operating water temperature of this
filter system is 100 °F (37.8 °C).
• Protect filter from freezing. Drain filter when
temperatures drop below 40 °F (4.4 °C).
• The disposable filter cartridge MUST be replaced
every 6 months, at the rated capacity or if a
noticeable reduction in flow rate occurs.
• To protect it from freezing, remove filter
cartridge when temperatures are expected to
drop below 33° F.
• Do not install systems in areas where ambient
temperatures may go above 110° F (43.3° C).
• Where a backflow prevention device is installed
on a water system, a device for controlling
pressure due to thermal expansion must be
installed.
MAINTENANCE 41
• Ensure all tubing and fittings are secure and free
from leaks.
water filter upright, once it is removed, to
prevent any remaining water from spilling out of
the water filter.
Replacing the Water Filter
• Replace the water filter:
- Approximately every six months.
- When the Water Filter LED turns on.
- When the water dispenser output decreases.
• To purchase a replacement water filter:
- Visit your local dealer or distributor
- Search using "water filter" on lg.com
4
Replace with a new water filter.
- Use replacement cartridge: LT1000P,
LT1000PC, LT1000PCS or ADQ747935**
• Take the new water filter out of its packing
and remove the protective cover from the o-
rings. With the water filter tabs in the
horizontal position, push the new water
filter into the manifold hole and turn it
clockwise until it stops.
1
If the top shelf, located below the water filter,
is in the highest position, it will need to be
removed prior to replacing the water filter.
• To remove any shelf, tilt the one side of the
shelf and lift it. Pull the shelf out.
5
6
Close the water filter cover. The cover will click
when closed correctly.
2
3
Pinch the sides to open the water filter cover.
After the water filter is replaced, dispense 2.5
gallons of water (flush for approximately 5
minutes) to remove trapped air and
contaminants from the system.
Pull the water filter downward and turn it
counterclockwise before pulling it out.
• Make sure to rotate the filter down
completely before pulling it out of the
manifold hole.
NOTE
• Do not dispense the entire 2.5 gallon amount
continuously. Press and release the dispenser
pad for cycles of 30 seconds ON and 60 seconds
OFF.
NOTE
• Replacing the water filter causes a small amount
of water (around 1 oz. or 25 cc) to drain.
• Wrap a cloth around the front end of the water
filter cover to collect any leaking water. Hold the
42 MAINTENANCE
7
After changing the filter, press and hold the
Water Filter button for three seconds to reset
the indicator light.
CAUTION
• LG strongly recommends that you use LG-
authorized water filters to prevent water quality
issues, water leakage and appliance
malfunction.
• For further assistance, call:
- 1-800-243-0000 (USA)
- 1-888-542-2623 (Canada)
MAINTENANCE 43
Performance Data Sheet
Model: LT1000P, LT1000PC, LT1000PCS
NSF System Trade Name Code: MDJ64844601
The concentration of the indicated substances in water entering the system was reduced to a
concentration less than or equal to the permissible limit for water leaving the system as specified in NSF/
ANSI Standard 42, Standard 53 and Standard 401.
System tested and certified by NSF International against NSF/ANSI Standard 42, Standard 53 and
Standard 401 for the reduction of substances listed below.
Max
Average
Average
Influent
Challeng
e
Permissible
Product
Water
NSF
Reduction
Requireme
nts
NSF Specified
Challenge
Concentration
Avg %
Reductio
n
Product
Water
Substance
Reduction
Concentrati
on
Concentrati
on
Chlorine Taste
and Odor
2.0 μg/L
2.0 μg/L± 10%
>97.5%
99.80%
0.050 μg/L
N/A
2 50.00%
Nominal
12,000,00 At least 10,000
24,000 pts/
ml
N/A
2 85.00%
Particulate Class 0 pts/mL
I, , 2 0.5 to < 1.0
μm
particles/mL
7
8
Asbestos
180 MFL
>99.00%
< 1 MFL
N/A
2 99.00%
10 to 10 MFL;
fibers greater
than 10 μg/Lin
length
Atrazine
Benzene
Carbofuran
Lindane
8.5 μg/L
15.0 μg/L
74.0 μg/L
1.9 μg/L
9.0 μg/L ± 10%
15.0 μg/L ± 10%
80.0 μg/L ± 10%
2.0 μg/L ± 10%
>94.10%
>96.60%
98.30%
0.500 μg/L
0.510 μg/L
1.258 μg/L
0.019 μg/L
0.460 μg/L
3.0 μg/L
5.0 μg/L
40 μg/L
0.2 μg/L
75.0 μg/L
NA
NA
NA
NA
NA
>99.00%
>99.80%
P-
230.0 μg/
L
225.0 μg/L ±
10%
Dichlorobenzen
e
2,4-D
210.0 μg/
210.0 μg/L ±
>99.90%
99.60%
>99.70%
91.00%
92.5%
0.210 μg/L
0.560 μg/L
<0.500 μg/L
0.531 μg/L
0.420 μg/L
10 cysts/L
10.80 ng/L
70.0 μg/L
10.0 μg/L
10.0 μg/L
2.0 μg/L
2.0 μg/L
N/A
NA
NA
NA
NA
NA
L
10%
Lead pH @6.5
Lead pH @8.5
140.0 μg/
L
150.0 μg/L ±
10%
150.0 μg/
L
150.0 μg/L ±
10%
Mercury @
pH6.5
5.9 μg/L
6.0 μg/L ± 10%
Mercury @
pH8.5
5.6 μg/L
6.0 μg/L ± 10%
Cyst*
100,000
cysts/L
Minimum
50,000 cysts/L
>99.99%
> 95.50%
2 99.95%
Atenolol
240 ng/L
200 ± 40% ng/L
30 ng/L
NA
44 MAINTENANCE
Max
Permissible
Product
Water
Concentrati
on
Average
Product
Water
Concentrati
on
Average
NSF
Reduction
Requireme
nts
NSF Specified
Challenge
Concentration
Avg %
Reductio
n
Substance
Reduction
Influent
Challeng
e
Carbamazepine
DEET
1600 ng/L 1400 ± 40% ng/L 98.40%
1600 ng/L 1400 ± 40% ng/L 97.10%
25.60 ng/L
46.40 ng/L
5.44 ng/L
5.44 ng/L
10.40 ng/L
22.00 ng/L
5.46 ng/L
4.68 ng/L
22.00 ng/L
46.40 ng/L
200 ng/L
200 ng/L
20 ng/L
20 ng/L
30 ng/L
60 ng/L
20 ng/L
20 ng/L
300 ng/L
200 ng/L
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
Trimethoprim
Linuron
170 ng/L
160 ng/L
200 ng/L
400 ng/L
140 ng/L
120 ng/L
140 ± 40% ng/L
140 ± 40% ng/L
200 ± 40% ng/L
400 ± 40% ng/L
140 ± 40% ng/L
140 ± 40% ng/L
>96.80%
>96.60%
>94.80%
>94.50%
>96.10%
>96.10%
Phenytoin
Ibuprofen
Naproxen
Estrone
Bisphenol A
Nonyl Phenol
2000 ng/L 2000 ± 40% ng/L >98.90%
1600 ng/L 1400 ± 40% ng/L >97.10%
* Based on the use of Cryptosporidium parvum oocysts.
Guidelines for Application / Water Supply Parameters
0.5 gpm (1.9 lpm)
Service Flow
Water Supply
Water Pressure
Water Temperature
Capacity
Community or Private Well - Potable Water
20 – 120 psi (138 – 827 kPa)
33 °F – 100 °F (0.6 °C – 37.8°C)
200 gallons (757 liters)
It is essential that the manufacturer’s recommended installation, maintenance and filter replacement
requirements be carried out for the product to perform as advertised.
NOTE
• While the testing was performed under standard laboratory conditions, actual performance may vary.
For replacement filters, visit your local dealer or distributor or search under "water filters" on the lg.com
website.
For further assistance, contact the LG Electronics Customer Information Center.
USA: 1-800-243-0000
Canada: 1-888-542-2623
Replacement Cartridge: LT1000P, LT1000PC, LT1000PCS or ADQ747935**
LG is a trademark of LG Corp.
NSF is a trademark of NSF International.
Manufactured by LG Electronics, INC:
170, Sungsanpaechoungro, Seongsan-gu, Gyeongsangnam-do, THE REPUBLIC OF KOREA
TROUBLESHOOTING 45
TROUBLESHOOTING
FAQs
Frequently Asked Questions
Q:
What are the best temperature settings for my refrigerator and freezer?
A:
The default setting for the refrigerator is 37° Fahrenheit (3° Celsius). The default setting for the
freezer is 0° Fahrenheit (-18° Celsius). Adjust these settings as necessary to keep food at desired
temperatures. Milk should be cold when stored on the inner shelf of the refrigerator. Ice cream
should be firm and ice cubes should not melt in the freezer. To switch the display from Fahrenheit to
Celsius, press and hold the Freezer and Refrigerator buttons until you hear a beep and the settings
in the display change.
Q:
How do I set the refrigerator and freezer temperatures?
A:
Continually press the Refrigerator or Freezer button on the control panel until the desired
temperature appears. The numbers will cycle from highest to lowest and then return to the highest
again with continuous pressing.
Q:
Why do I hear a buzzing noise from my refrigerator periodically?
A:
This may happen if you do not have a water source attached to your refrigerator and the icemaker is
turned on. If you do not have a water source attached to the back of the refrigerator you should turn
the icemaker off.
Q:
Why does the icemaker tray look crooked?
A:
This is a normal part of the icemaker cycle. The icemaker tray may appear level or with a slight tilt.
The change in position is to assist in the freezing process.
Q:
My refrigerator is powered on and the controls are working, but it’s not cooling and the display
shows “OFF” (see below). What is wrong?
A:
The refrigerator is in Display Mode. The Display Mode disables all cooling in the refrigerator and
freezer sections to conserve energy while on display in a retail store. When activated, OFF is displayed
on the control panel and the display remains on for 20 seconds. With either refrigerator door opened,
press the Ice Plus button 3 times consecutively while pressing the Refrigerator button. The control
panel beeps and the temperature settings display to confirm that Display Mode is deactivated. Use
the same procedure to activate Display Mode.
TM
Q:
How do I change the Craft Ice settings?
A:
Press the Craft Ice button repeatedly to scroll through the 3 ICE, 6 ICE and OFF modes. For clearer
ice, select the 3 ICE mode. For more ice, select the 6 ICE mode.
46 TROUBLESHOOTING
Before Calling for Service
Review this section before calling for service; doing so will save you both time and money.
Cooling
Problem
Possible Cause & Solution
Refrigerator is not
cooling or has no
power.
A fuse in your home may be blown or the circuit breaker tripped. Or the appliance is
connected to a GFCI (Ground Fault Circuit Interrupter) outlet, and the outlet's circuit
breaker has tripped.
• Check the main electrical box and replace the fuse or reset the circuit breaker. Do not
increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified
electrician.
• Reset the circuit breaker on the GFCI. If the problem persists, contact an electrician.
The refrigerator control is set to OFF (some models).
• Turn the control ON. Refer to the Setting the Controls section for proper temperature
settings.
Refrigerator is set to Demo Mode.
• Demo Mode allows the lights and control display to work normally while disabling cooling,
to save energy while the refrigerator is on the showroom floor. See the FAQs section of
this manual for instructions on how to disable Demo Mode.
Refrigerator is in the defrost cycle.
• During the defrost cycle, the temperature of each compartment may rise slightly. Wait 30
minutes and confirm the proper temperature has been restored once the defrost cycle has
completed.
Refrigerator was recently installed.
• It may take up to 24 hours for each compartment to reach the desired temperature.
Refrigerator was recently relocated.
• If the refrigerator was stored for a long period of time or moved on its side, it is necessary
for the refrigerator to stand upright for 24 hours before connecting it to power.
Cooling system runs
too much.
Refrigerator is replacing an older model.
• Modern refrigerators require more operating time but use less energy due to more
efficient technology.
Refrigerator was recently plugged in or power restored.
• The refrigerator will take up to 24 hours to cool completely.
The door is opened often or a large amount of food / hot food was added.
• Adding food and opening the door warms the refrigerator, requiring the compressor to
run longer in order to cool the refrigerator back down. In order to conserve energy, try to
get everything you need out of the refrigerator at once, keep food organized so it is easy
to find, and close the door as soon as the food is removed. (Refer to the Food Storage
Guide.)
Doors are not closed completely.
• Firmly push the doors shut. If they will not shut all the way, the "Doors will not close
correctly or pop open" section in Troubleshooting.
Refrigerator is installed in a hot location.
• The compressor will run longer under warm conditions. At normal room temperatures (70
°F or 21 °C) expect your compressor to run about 40 % to 80 % of the time. Under warmer
conditions, expect it to run even more often. The refrigerator should not be operated
above 110 °F (43 °C).
TROUBLESHOOTING 47
Problem
Possible Cause & Solution
Condenser / back cover is clogged.
Cooling system runs
too much.
• Use a vacuum cleaner with an attachment to clean the condenser cover and vents. Do not
remove the panel covering the condenser coil area.
Interior moisture
buildup.
Doors are opened often or for long periods of time.
• When the doors are opened often or for long periods of time, warm, humid air enters the
compartment. This raises the temperature and moisture level within the compartment. To
lessen the effect, reduce the frequency and duration of door openings.
Doors are not closed correctly.
• See the "Doors will not close correctly or pop open" section.
Weather is humid.
• Humid weather allows additional moisture to enter the compartments when the doors are
opened leading to condensation or frost. Maintaining a reasonable level of humidity in the
home will help to control the amount of moisture that can enter the compartments.
Defrost cycle recently completed.
• During the defrost cycle, the temperature of each compartment may rise slightly and
condensation may form on the back wall. Wait 30 minutes and confirm that the proper
temperature has been restored once the defrost cycle has completed.
Food is not packaged correctly.
• Food stored uncovered or unwrapped, and damp containers can lead to moisture
accumulation within each compartment. Wipe all containers dry and store food in sealed
packaging to prevent condensation and frost.
Food is freezing in
the refrigerator
compartment.
Food with high water content was placed near an air vent.
• Rearrange items with high water content away from air vents.
Refrigerator temperature control is set incorrectly.
• If the temperature is too cold, adjust the control one increment at a time and wait for the
temperature to stabilize. Refer to the Control Panel section for more information.
Refrigerator is installed in a cold location.
• When the refrigerator is operated in temperature below 41 °F (5 °C), food can freeze in the
refrigerator compartment. The refrigerator should not be operated in temperature below
55 °F (13 °C).
Refrigerator or
Freezer section is too
cold.
Incorrect temperature control settings.
• If the temperature is too cold, adjust the control one increment at a time and wait for the
temperature to stabilize. Refer to the Control Panel for more information.
Frost or ice crystals
form on frozen food
(inside of sealed
package).
Condensation from food with a high water content has frozen inside of the food
package.
• This is normal for food items with a high water content.
Food has been left in the freezer for a long period of time.
• Do not store food items with high water content in the freezer for a long period of time.
Frost or ice crystals
form on frozen food
(outside of package).
Door is opened frequently or for long periods of time.
• When the doors are opened often or for long periods of time, warm, humid air enters the
compartment. This raises the temperature and moisture level within the compartment.
Increased moisture will lead to frost and condensation. To lessen the effect, reduce the
frequency and duration of door openings.
Door is not closing properly.
• Refer to the "Doors will not close correctly or pop open" section in the Troubleshooting.
Refrigerator or
Freezer section is too
warm.
Refrigerator was recently installed.
• It may take up to 24 hours for each compartment to reach the desired temperature.
48 TROUBLESHOOTING
Problem
Possible Cause & Solution
Refrigerator or
The air vents are blocked. Cold air circulates from the freezer to the fresh food section
Freezer section is too and back again through air vents in the wall dividing the two sections.
warm.
• Locate air vents by using your hand to sense airflow and move all packages that block
vents and restrict airflow. Rearrange items to allow air to flow throughout the
compartment.
Doors are opened often or for long periods of time.
• When the doors are opened often or for long periods of time, warm, humid air enters the
compartment. This raises the temperature and moisture level within the compartment. To
lessen the effect, reduce the frequency and duration of door openings.
Unit is installed in a hot location.
• The refrigerator should not be operated in temperatures above 110 °F (43 °C).
A large amount of food or hot food was added to either compartment.
• Adding food warms the compartment requiring the cooling system to run. Allowing hot
food to cool to room temperature before putting it in the refrigerator will reduce this
effect.
Doors are not closed correctly.
• See the "Doors will not close correctly or pop open" section in the Troubleshooting.
Temperature control is not set correctly.
• If the temperature is too warm, adjust the control one increment at a time and wait for the
temperature to stabilize.
Defrost cycle has recently completed.
• During the defrost cycle, the temperature of each compartment may rise slightly and
condensation may form on the back wall. Wait 30 minutes and confirm the proper
temperature has been restored once the defrost cycle has completed.
Craft Ice
Problem
Possible Cause & Solution
Icemaker is not
making ice.
Refrigerator was recently installed or icemaker recently connected.
• The icemaker begins producing ice approximately 48 hours after the appliance is initially
installed. The first batches of ice may not be round and clear.
Icemaker is not
making enough ice.
In 3 ICE mode, the Craft Ice icemaker produces 1 batch of round ice about every 24
hours.
• For more ice, select the 6 ICE mode which produces 2 batches every 24 hours.
Ice
Problem
Possible Cause & Solution
Icemaker is not
making enough ice.
Demand exceeds ice production capacity.
• Refer to the Automatic Icemaker section for ice production capacity to check the amount
of ice produced in a 24 hour period.
House water supply is not connected, valve is not turned on fully, or valve is clogged.
• Connect the refrigerator to a cold water supply with adequate pressure and turn the water
shutoff valve fully open. If the problem persists, it may be necessary to contact a plumber.
TROUBLESHOOTING 49
Problem
Possible Cause & Solution
Water filter has been exhausted.
• Replacing the water filter is recommended:
Icemaker is not
making enough ice.
-
-
-
-
Approximately every six months.
When the water filter indicator turns on.
When the water dispenser output decreases.
When the ice cubes are smaller than normal.
Low house water supply pressure.
• The water pressure must be between 20 and 120 psi (138 and 827 kPa) on models without
a water filter and between 40 and 120 psi (276 and 827 kPa) on models with a water filter.
If the problem persists, it may be necessary to contact a plumber.
Reverse osmosis filtration system is used.
• Reverse osmosis filtration systems can reduce the water pressure below the minimum
amount and result in icemaker issues. (Refer to the Connecting the Water Line section.)
Tubing connecting refrigerator to house supply valve is kinked.
• The tubing can kink when the refrigerator is moved during installation or cleaning
resulting in reduced water flow. Straighten or repair the water supply line and arrange it to
prevent future kinks.
Doors are opened often or for long periods of time.
• If the doors of the unit are opened often, ambient air will warm the refrigerator which will
prevent the unit from maintaining the set temperature. Lowering the refrigerator
temperature can help, as well as not opening the doors as frequently.
Doors are not closed completely.
• If the doors are not properly closed, ice production will be affected. See the "Doors will not
close correctly or pop open" section in Parts & Features Troubleshooting for more
information.
The temperature setting for the freezer is too warm.
• The recommended temperature for the freezer compartment for normal ice production is
0 °F (-18 °C). If the freezer temperature is warmer, ice production will be affected.
Icemaker is not
making ice
Refrigerator was recently installed or icemaker recently connected.
• It may take up to 24 hours for each compartment to reach the desired temperature and
for the icemaker to begin making ice.
Icemaker is not turned on.
• Locate the icemaker ON/OFF and confirm that it is turned on.
The ice detecting sensor is obstructed.
• Foreign substances or frost on the ice-detecting sensor can interrupt ice production. Make
sure that the sensor area is clean at all times for proper operation.
The refrigerator is not connected to a water supply or the supply shutoff valve is not
turned on.
• Connect the refrigerator to the water supply and turn the water shutoff valve fully open.
Icemaker shutoff (arm or sensor) obstructed.
• If your icemaker is equipped with an ice shutoff arm, make sure that the arm moves freely.
If your icemaker is equipped with the electronic ice shutoff sensor, make sure that there is
a clear path between the two sensors.
Reverse osmosis water filtration system is connected to your cold water supply.
• Reverse osmosis filtration systems can reduce the water pressure below the minimum
amount and result in icemaker issues. (Refer to the Connecting the Water Line section.)
50 TROUBLESHOOTING
Problem
Possible Cause & Solution
Ice has bad taste or
odor.
Water supply contains minerals such as sulfur.
• A water filter may need to be installed to eliminate taste and odor problems. NOTE: In
some cases, a filter may not help. It may not be possible to remove all minerals/odor/taste
in all water supplies.
Icemaker was recently installed.
• Ice that has been stored for too long will shrink, become cloudy, and may develop a stale
taste. Throw away old ice and make a new supply.
The food has not been stored properly in either compartment.
• Rewrap the food. Odors may migrate to the ice if food is not wrapped properly.
The interior of the refrigerator needs to be cleaned.
• See the Maintenance section for more information.
The ice storage bin needs to be cleaned.
• Empty and wash the bin (discard old cubes). Make sure that the bin is completely dry
before reinstalling it.
Icemaker is making
too much ice.
Icemaker shutoff (arm/ sensor) is obstructed.
• Empty the ice bin. If your icemaker is equipped with an ice shutoff arm, make sure that the
arm moves freely. If your icemaker is equipped with the electronic ice shutoff sensor,
make sure that there is a clear path between the two sensors. Reinstall the ice bin and wait
24 hours to confirm proper operation.
Ice is not dispensing. Unable to hear the sound of ice coming out?
• In the control panel, select the modes for cubed ice and crushed ice alternately to dispense
the ice.
Doors are not closed completely.
• Ice will not dispense if any of the refrigerator doors are left open.
Infrequent use of the dispenser.
• Infrequent use of the ice dispenser will cause the cubes to stick together over time, which
will prevent them from properly dispensing. Check the ice bin for ice cubes clumping/
sticking together. If they are, break up the ice cubes to allow for proper operation.
The delivery chute is clogged with frost or ice fragments.
• Eliminate the frost or ice fragments by removing the ice bin and clearing the chute with a
plastic utensil. Dispensing cubed ice can also help prevent frost or ice fragment buildup.
The dispenser display is locked.
• Press and hold the Lock button for three seconds to unlock the control panel and
dispenser.
Ice bin is empty.
• It may take up to 24 hours for each compartment to reach the desired temperature and
for the icemaker to begin making ice. Make sure that the shutoff (arm/sensor) is not
obstructed. Once the ice supply in the bin has been completely exhausted, it may take up
to 90 minutes before additional ice is available, and approximately 24 hours to completely
refill the bin.
TROUBLESHOOTING 51
Water
Problem
Possible Cause & Solution
Water filter has been exhausted.
• Replacing the water filter is recommended:
Water is dispensing
slowly.
-
-
-
-
Approximately every six months.
When the water filter indicator turns on.
When the water dispenser output decreases.
When the ice cubes are smaller than normal.
Reverse osmosis filtration system is used.
• Reverse osmosis filtration systems can reduce the water pressure below the minimum
amount and result in icemaker issues. If the problem persists, it may be necessary to
contact a plumber.
Low house water supply pressure.
• The water pressure must be between 20 and 120 psi on models without a water filter and
between 40 and 120 psi on models with a water filter. If the problem persists, it may be
necessary to contact a plumber.
Water is not
dispensing.
New installation or water line recently connected.
• Dispense 2.5 gallons of water (flush for approximately 5 minutes) to remove trapped air
and contaminants from the system. Do not dispense the entire 2.5 gallon amount
continuously. Depress and release the dispenser pad for cycles of 30 seconds ON and 60
seconds OFF.
The dispenser panel is locked.
• Press and hold the Lock button for three seconds to unlock the control panel and
dispenser.
The dispenser is not set for water dispensing.
• The dispenser can be set for ice or water. Make certain that the control panel is set for the
proper operation. Press the Water button on the control panel to dispense water.
Refrigerator or freezer doors are not closed properly.
• Water will not dispense if any of the refrigerator doors are left open.
Water filter has been recently removed or replaced.
• After the water filter is replaced, dispense 2.5 gallons of water (flush for approximately five
minutes) to remove trapped air and contaminants from the system. Do not dispense the
entire 2.5 gallon amount continuously. Depress and release the dispenser pad for cycles of
30 seconds ON and 60 seconds OFF.
Tubing connecting refrigerator to house supply valve is kinked.
• The tubing can kink when the refrigerator is moved during installation or cleaning.
Resulting in reduced water flow. Straighten or repair the water supply line and arrange it
to prevent future kinks.
The house water supply is not connected, the valve is not turned on fully, or the valve is
clogged.
• Connect the refrigerator to the water supply and turn the water shutoff valve fully open. If
the problem persists, it may be necessary to contact a plumber.
Dispensing warm
water.
Refrigerator was recently installed.
• Allow 24 hours after installation for the water storage tank to cool completely.
The water dispenser has been used recently and the storage tank was exhausted.
• Depending on your specific model, the water storage capacity will range from
approximately 20 to 30 oz.
52 TROUBLESHOOTING
Problem
Possible Cause & Solution
Dispensing warm
water.
Dispenser has not been used for several hours.
• If the dispenser has not been used for several hours, the first glass dispensed may be
warm. Discard the first 10oz.
Refrigerator is connected to the hot water supply.
• Make sure that the refrigerator is connected to a cold water pipe.
WARNING: Connecting the refrigerator to a hot water line may damage the
icemaker.
Water has bad taste
or odor.
Water supply contains minerals such as sulfur.
• A water filter may need to be installed to eliminate taste and odor problems.
Water filter has been exhausted.
• Replacing the water filter is recommended:
-
-
-
-
Approximately every six months.
When the water filter indicator turns on.
When the water dispenser output decreases.
When the ice cubes are smaller than normal.
Refrigerator was recently installed.
• Dispense 2.5 gallons of water (flush for approximately 5 minutes) to remove trapped air
and contaminants from the system. Do not dispense the entire 2.5 gallon amount
continuously. Depress and release the dispenser pad for cycles of 30 seconds ON and 60
seconds OFF.
Parts & Features
Problem
Possible Cause & Solution
Doors will not close
correctly or pop
open.
Food packages are blocking the door open.
• Rearrange food containers to clear the door and door shelves.
Ice bin, crisper cover, pans, shelves, door bins, or baskets are out of position.
• Push bins all the way in and put crisper cover, pans, shelves and baskets into their correct
positions. See the Operation section for more information.
The doors were removed during product installation and not properly replaced.
• Remove and replace the doors according to the Removing and Replacing Refrigerator
Handles and Doors section.
Refrigerator is not leveled properly.
• See Door Alignment in the Refrigeration Installation section to level refrigerator.
Doors are difficult to The gaskets are dirty or sticky.
open.
• Clean the gaskets and the surfaces that they touch. Rub a thin coat of appliance polish or
kitchen wax on the gaskets after cleaning.
Door was recently closed.
• When you open the door, warmer air enters the refrigerator. As the warm air cools, it can
create a vacuum. If the door is hard to open, wait one minute to allow the air pressure to
equalize, then see if it opens more easily.
Refrigerator wobbles Leveling legs are not adjusted properly.
or seems unstable
• Refer to the Leveling and Door Alignment section.
Floor is not level.
• It may be necessary to add shims under the leveling legs or rollers to complete installation.
TROUBLESHOOTING 53
Problem
Possible Cause & Solution
Lights do not work.
LED interior lighting failure.
• The refrigerator compartment lamp is LED interior lighting, and service should be
performed by a qualified technician.
Refrigerator has an
unusual odor.
The Air Filter may need to be set to the MAX setting or replaced.
• Set the Air Filter to the MAX setting. If the odor does not go away within 24 hours, the filter
may need to be replaced. See the Replacing the Air Filter section for replacement
instructions.
The interior of the
refrigerator is
covered with dust or
soot.
The refrigerator is located near a fire source, such as a fireplace, chimney, or candle.
• Make sure that the refrigerator is not located near a fire source, such as a fireplace,
chimney or candle.
Noises
Problem
Clicking
Possible Cause & Solution
The defrost control will click when the automatic defrost cycle begins and ends. The
thermostat control (or refrigerator control on some models) will also click when cycling
on and off.
• Normal Operation
Rattling
Rattling noises may come from the flow of refrigerant, the water line on the back of
the unit, or items stored on top of or around the refrigerator.
• Normal Operation
Refrigerator is not resting solidly on the floor.
• Floor is weak or uneven or leveling legs need to be adjusted. See the Leveling and Door
Alignment section.
Refrigerator with linear compressor was jarred while running.
• Normal Operation
Whooshing
Evaporator fan motor is circulating air through the refrigerator and freezer
compartments.
• Normal Operation
Air is being forced over the condenser by the condenser fan.
• Normal Operation
Gurgling
Popping
Sizzling
Refrigerant flowing through the cooling system.
• Normal Operation
Contraction and expansion of the inside walls due to changes in temperature.
• Normal Operation
Water dripping on the defrost heater during a defrost cycle.
• Normal Operation
Vibrating
If the side or back of the refrigerator is touching a cabinet or wall, some of the normal
vibrations may make an audible sound.
• To eliminate the noise, make sure that the sides and back cannot vibrate against any wall
or cabinet.
Dripping
Water running into the drain pan during the defrost cycle.
• Normal Operation
54 TROUBLESHOOTING
Problem
Possible Cause & Solution
Pulsating or high-
pitched sound
Your refrigerator is designed to run more efficiently to keep your food items at the
desired temperature. The high efficiency compressor may cause your new refrigerator
to run longer than your old one, but it is still more energy efficient than previous
models. While the refrigerator is running, it is normal to hear a pulsating or high-
pitched sound.
• Normal Operation
Wi-Fi
Problem
Possible Cause & Solution
Trouble connecting
appliance and
smartphone to Wi- Fi
network
The password for the Wi-Fi network was entered incorrectly.
• Delete your home Wi-Fi network and begin the registration process again.
• If you are connecting to an iPhone, the password to connect to the module in the
refrigerator is the last 4 characters of the network name, repeated twice.
Mobile data for your smartphone is turned on.
• Turn off the Mobile data on your smartphone before registering the appliance.
The wireless network name (SSID) is set incorrectly.
• The wireless network name (SSID) should be a combination of English letters and
numbers. (Do not use special characters.)
The router frequency is not 2.4 GHz.
• Only a 2.4 GHz router frequency is supported. Set the wireless router to 2.4 GHz and
connect the appliance to the wireless router. To check the router frequency, check with
your Internet service provider or the router manufacturer.
The distance between the appliance and the router is too far.
• If the appliance is too far from the router, the signal may be weak and the connection may
not be configured correctly. Move the router closer to the appliance or purchase and
install a Wi-Fi repeater.
LIMITED WARRANTY 55
LIMITED WARRANTY
USA
TERMS AND CONDITIONS
ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT
REQUIRES YOU AND LG ELECTRONICS (“LG”) TO RESOLVE DISPUTES BY BINDING ARBITRATION
INSTEAD OF IN COURT, UNLESS YOU CHOOSE TO OPT OUT. IN ARBITRATION, CLASS ACTIONS AND
JURY TRIALS ARE NOT PERMITTED. PLEASE SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING
DISPUTES” BELOW.
Should your LG Refrigerator ("Product") fail due to a defect in materials or workmanship under normal and
proper use, during the warranty period set forth below, LG will, at its option, repair or replace the Product.
This limited warranty is valid only to the original retail purchaser of the Product ("You") and applies only
when purchased lawfully and used within the United States including U.S. Territories.
WARRANTY PERIOD
Sealed System
(Condenser, Dryer,
Connecting Tube and
Evaporator)
Refrigerator/Freezer
Compressor
One (1) year from the
date of original retail
purchase
Five (5) years from the
date of original retail
purchase
Five (5) years from the
date of original retail
purchase
Linear / Inverter
Compressor Only : Parts
Only for years 6-10 from
the date of original retail
purchase (Consumer will
be charged for labor.)
Parts and Labor (internal/ Parts and Labor
functional parts only)
Parts and Labor
• Replacement Products and parts are warranted for the remaining portion of the original warranty period
or ninety (90) days, whichever is greater.
• Replacement Products and parts may be new, reconditioned, refurbished, or otherwise factory
remanufactured.
• Replaced Product or part(s) will be the property of LG.
• Proof of original retail purchase specifying the Product model and date of purchase is required to obtain
warranty service under this limited warranty.
• Warranty start date will be ninety (90) days from manufacture date absent valid proof of purchase.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THE PRODUCT IS LIMITED IN
DURATION TO THE DURATION OF THE ABOVE LIMITED WARRANTY. UNDER NO CIRCUMSTANCES
SHALL LG OR ITS U.S. DISTRIBUTORS/DEALERS BE LIABLE FOR ANY INDIRECT, INCIDENTAL,
CONSEQUENTIAL, SPECIAL, OR PUNITIVE DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST
GOODWILL, LOST REVENUES OR PROFITS, WORK STOPPAGE, IMPAIRMENT OF OTHER GOODS, COST OF
REMOVAL AND REINSTALLATION OF THE PRODUCT, LOSS OF USE, OR ANY OTHER DAMAGES WHETHER
BASED IN CONTRACT, TORT, OR OTHERWISE. LG’S TOTAL LIABILITY, IF ANY, SHALL NOT EXCEED THE
PURCHASE PRICE PAID BY YOU FOR THE PRODUCT.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
THIS LIMITED WARRANTY DOES NOT COVER:
• Service trips to deliver, pick up, or install, educate how to operate, correct wiring, or correct
unauthorized repairs.
56 LIMITED WARRANTY
• Damage or failure of the Product to perform during power failures and interrupted or inadequate
electrical service.
• Damage or failure of the Product caused by leaky or broken water pipes, frozen water pipes, restricted
drain lines, inadequate or interrupted water supply or inadequate supply of air.
• Damage or failure of the Product resulting from operating the Product in a corrosive atmosphere or
contrary to the Product owner’s manual.
• Damage or failure of the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, acts
of nature, or any other causes beyond the control of LG.
• Damage or failure of the Product caused by unauthorized modification or alteration, or if the Product is
used for other than the intended purpose, or any water leakage where the Product was not properly
installed.
• Damage or failure of the Product caused by incorrect electrical current, voltage, or plumbing codes.
• Damage or failure of the Product caused by transportation, storage, and/or handling, including
scratches, dents, chips, and/or other damage to the finish of the Product, unless such damage is
reported within one (1) week of delivery.
• Damage or missing items to any display, open box, or discounted Product.
• Refurbished Product or any Product sold “As Is”, “Where Is”, “With all Faults”, or similar disclaimer.
• Products with original serial numbers that have been removed, altered, or cannot be readily determined.
• Increases in utility costs and additional utility expenses.
• Any noises associated with normal operation.
• Products used for other than normal and proper household use (e.g., commercial or industrial use,
offices, and recreational facilities or vehicles) or contrary to the Product owner’s manual.
• Costs associated with removal and reinstallation of the Product for repairs.
• Replacement of light bulbs, filters, or any consumable parts.
• The removal and reinstallation of the Product if it is installed in an inaccessible location or is not installed
in accordance with the Product owner’s manual.
• Damage or failure of the Product resulting from misuse, abuse, improper installation, repair, or
maintenance. Improper repair includes the use of parts not authorized by LG. Improper installation or
maintenance includes installation or maintenance contrary to the Product owner’s manual.
• Damage or failure of the Product caused by the use of parts, components, accessories (e.g., water filters,
etc.), consumable cleaning products, any other products, or services that are not authorized by LG.
• Shelves, door bins, drawers, handle and accessories, except for internal/functional parts covered under
this limited warranty.
The cost of repair or replacement under these excluded circumstances shall be borne by You.
TO OBTAIN WARRANTY SERVICE AND ADDITIONAL INFORMATION
Call 1-800-243-0000 and select the appropriate option from the menu.
Or visit our website at http://www.lg.com
Or by mail: LG Electronics Customer Service P.O. Box 240007 Huntsville, AL 35813 ATTN: CIC
PROCEDURE FOR RESOLVING DISPUTES:
ALL DISPUTES BETWEEN YOU AND LG ARISING OUT OF OR RELATING IN ANY WAY TO THIS LIMITED
WARRANTY OR THE PRODUCT SHALL BE RESOLVED EXCLUSIVELY THROUGH BINDING ARBITRATION, AND
NOT IN A COURT OF GENERAL JURISDICTION. BINDING ARBITRATION MEANS THAT YOU AND LG ARE EACH
WAIVING THE RIGHT TO A JURY TRIAL AND TO BRING OR PARTICIPATE IN A CLASS ACTION.
Definitions. For the purposes of this section, references to “LG” mean LG Electronics U.S.A., Inc., its
parents, subsidiaries and affiliates, and each of their officers, directors, employees, agents, beneficiaries,
predecessors in interest, successors, assigns and suppliers; references to “dispute” or “claim” shall include
any dispute, claim or controversy of any kind whatsoever (whether based in contract, tort, statute,
LIMITED WARRANTY 57
regulation, ordinance, fraud, misrepresentation or any other legal or equitable theory) arising out of or
relating in any way to the sale, condition or performance of the product or this Limited Warranty.
Notice of Dispute. In the event you intend to commence an arbitration proceeding, you must first notify
LG in writing at least 30 days in advance of initiating the arbitration by sending a letter to LG at LG
Electronics, USA, Inc. Attn: Legal Department- Arbitration 111 Sylvan Avenue, Englewood Cliffs, NJ 07632.
You and LG agree to engage in good faith discussions in an attempt to amicably resolve your claim. The
notice must provide your name, address, and telephone number; identify the product that is the subject of
the claim; and describe the nature of the claim and the relief being sought. If you and LG are unable to
resolve the dispute within 30 days, either party may proceed to file a claim for arbitration.
Agreement to Binding Arbitration and Class Action Waiver. Upon failure to resolve the dispute during
the 30 day period after sending written notice to LG, you and LG agree to resolve any claims between us
only by binding arbitration on an individual basis, unless you opt out as provided below. Any dispute
between you and LG shall not be combined or consolidated with a dispute involving any other person’s or
entity’s product or claim. More specifically, without limitation of the foregoing, any dispute between you
and LG shall not under any circumstances proceed as part of a class or representative action. Instead of
arbitration, either party may bring an individual action in small claims court, but that small claims court
action may not be brought on a class or representative basis.
Arbitration Rules and Procedures. To begin arbitration of a claim, either you or LG must make a written
demand for arbitration. The arbitration will be administered by the American Arbitration Association
(“AAA”) and will be conducted before a single arbitrator under the AAA’s Consumer Arbitration Rules that
are in effect at the time the arbitration is initiated (referred to as the “AAA Rules”) and under the
copy of your written demand for arbitration, as well as a copy of this provision, to the AAA in the manner
described in the AAA Rules. You must also send a copy of your written demand to LG at LG Electronics,
USA, Inc. Attn: Legal Department- Arbitration 111 Sylvan Avenue, Englewood Cliffs, NJ 07632. If there is a
conflict between the AAA Rules and the rules set forth in this section, the rules set forth in this section will
govern. This arbitration provision is governed by the Federal Arbitration Act. Judgment may be entered on
the arbitrator’s award in any court of competent jurisdiction. All issues are for the arbitrator to decide,
except that issues relating to the scope and enforceability of the arbitration provision and to the
arbitrability of the dispute are for the court to decide. The arbitrator is bound by the terms of this
provision.
Governing Law. The law of the state of your residence shall govern this Limited Warranty and any
disputes between us except to the extent that such law is preempted by or inconsistent with applicable
federal law.
Fees/Costs. You do not need to pay any fee to begin an arbitration. Upon receipt of your written demand
for arbitration, LG will promptly pay all arbitration filing fees to the AAA unless you seek more than $25,000
in damages, in which case the payment of these fees will be governed by the AAA Rules. Except as
otherwise provided for herein, LG will pay all AAA filing, administration and arbitrator fees for any
arbitration initiated in accordance with the AAA Rules and this arbitration provision. If you prevail in the
arbitration, LG will pay your attorneys’ fees and expenses as long as they are reasonable, by considering
factors including, but not limited to, the purchase amount and claim amount. Notwithstanding the
foregoing, if applicable law allows for an award of reasonable attorneys’ fees and expenses, an arbitrator
can award them to the same extent that a court would. If the arbitrator finds either the substance of your
claim or the relief sought in the demand is frivolous or brought for an improper purpose (as measured by
the standards set forth in Federal Rule of Civil Procedure 11(b)), then the payment of all arbitration fees will
be governed by the AAA Rules. In such a situation, you agree to reimburse LG for all monies previously
disbursed by it that are otherwise your obligation to pay under the AAA Rules. Except as otherwise
provided for, LG waives any rights it may have to seek attorneys’ fees and expenses from you if LG prevails
in the arbitration.
Hearings and Location. If your claim is for $25,000 or less, you may choose to have the arbitration
conducted solely on the basis of (1) documents submitted to the arbitrator, (2) through a telephonic
hearing, or (3) by an in-person hearing as established by the AAA Rules. If your claim exceeds $25,000, the
right to a hearing will be determined by the AAA Rules. Any in-person arbitration hearings will be held at a
location within the federal judicial district in which you reside unless we both agree to another location or
we agree to a telephonic arbitration.
Opt Out. You may opt out of this dispute resolution procedure. If you opt out, neither you nor LG can
require the other to participate in an arbitration proceeding. To opt out, you must send notice to LG no
58 LIMITED WARRANTY
later than 30 calendar days from the date of the first consumer purchaser’s purchase of the product by
either: (i) sending an e-mail to [email protected], with the subject line: “Arbitration Opt Out” or (ii) calling 1-
800-980-2973. You must include in the opt out e-mail or provide by telephone: (a) your name and address;
(b) the date on which the product was purchased; (c) the product model name or model number; and (d)
the serial number (the serial number can be found (i) on the product; or (ii) online by accessing https://
Number”).
You may only opt out of the dispute resolution procedure in the manner described above (that is, by e-mail
or telephone); no other form of notice will be effective to opt out of this dispute resolution procedure.
Opting out of this dispute resolution procedure will not affect the coverage of the Limited Warranty in any
way, and you will continue to enjoy the full benefits of the Limited Warranty. If you keep this product and
do not opt out, then you accept all terms and conditions of the arbitration provision described above.
LIMITED WARRANTY 59
Canada
TERMS AND CONDITIONS
ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT
REQUIRES YOU AND LG TO RESOLVE DISPUTES BY BINDING ARBITRATION INSTEAD OF IN COURT,
UNLESS THE LAWS OF YOUR PROVINCE OR TERRITORY DO NOT PERMIT THAT, OR, IN OTHER
JURISDICTIONS, IF YOU CHOOSE TO OPT OUT. IN ARBITRATION, CLASS ACTIONS AND JURY TRIALS
ARE NOT PERMITTED. PLEASE SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING DISPUTES”
BELOW.
Should your LG Refrigerator ("Product") fail due to a defect in materials or workmanship under normal and
proper use, during the warranty period set forth below, LG Electronics Canada, Inc. ("LGECI") will, at its
option, repair, replace or pro rate the Product upon receipt of proof of the original retail purchase. This
limited warranty is valid only to the original retail purchaser of the Product and applies only to a Product
distributed, purchased from an authorized retailer and used within Canada, as determined at the sole
discretion of LGECI.
WARRANTY PERIOD (Note: If the original date of purchase cannot be verified, the warranty will
begin sixty (60) days from the date of manufacture)
Sealed System (Condenser, Dryer, Connecting
Tube and Evaporator)
Linear / Inverter
Compressor
Refrigerator
One (1) year from the
date of original retail
purchase
One (1) year from the
date of original retail
purchase
Seven (7) years from the
date of original retail
purchase
Ten (10) years from the
date of original retail
purchase
Parts and Labor (internal/ Parts and Labor
functional parts only)
Parts only (Consumer will Part only (Consumer will
be charged for labor) be charged for labor)
• Replacement products and parts are warranted for the remaining portion of the original warranty period
or ninety (90) days, whichever is greater.
• Replacement products and parts may be new, reconditioned, refurbished, or otherwise factory
remanufactured, all at the sole discretion of LGECI.
• Proof of original retail purchase specifying the Product model and date of purchase is required to obtain
warranty service under this Limited Warranty.
LGECI’S SOLE LIABILITY IS LIMITED TO THE LIMITED WARRANTY SET OUT ABOVE. EXCEPT AS
EXPRESSLY PROVIDED ABOVE, LGECI MAKES NO, AND HEREBY DISCLAIMS, ALL OTHER WARRANTIES
AND CONDITIONS RESPECTING THE PRODUCT, WHETHER EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, AND NO REPRESENTATIONS SHALL BE BINDING ON LGECI. LGECI DOES NOT
AUTHORIZE ANY PERSON TO CREATE OR ASSUME FOR IT ANY OTHER WARRANTY OBLIGATION OR
LIABILITY IN CONNECTION WITH THE PRODUCT. TO THE EXTENT THAT ANY WARRANTY OR
CONDITION IS IMPLIED BY LAW, IT IS LIMITED TO THE WARRANTY PERIOD SET OUT ABOVE. UNDER
NO CIRCUMSTANCES SHALL LGECI, THE MANUFACTURER OR DISTRIBUTOR OF THE PRODUCT, BE
LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, DIRECT, INDIRECT, PUNITIVE OR
EXEMPLARY DAMAGES, INCLUDING, WITHOUT LIMITATION, LOSS OF GOODWILL, LOST PROFITS, LOSS
OF ANTICIPATED PROFITS, LOST REVENUE, LOSS OF USE, OR ANY OTHER DAMAGE, WHETHER ARISING
DIRECTLY OR INDIRECTLY FROM ANY CONTRACTUAL BREACH, FUNDAMENTAL BREACH, TORT OR
OTHERWISE, OR FROM ANY ACTS OR OMISSIONS. LGECI’S TOTAL LIABILITY, IF ANY, SHALL NOT
EXCEED THE PURCHASE PRICE PAID BY YOU FOR THE PRODUCT.
This Limited Warranty gives you specific legal rights. You may also have other rights that vary from
province to province depending on applicable provincial laws. Any term of this Limited Warranty that
negates or varies any implied condition or warranty under provincial law is severable where it conflicts
with such provincial law without affecting the remainder of this warranty’s terms.
60 LIMITED WARRANTY
THIS LIMITED WARRANTY DOES NOT COVER:
• Service trips to i) deliver, pick up, or install or; educate on how to operate the Product; ii) correct wiring or
plumbing; or iii) correct unauthorized repairs or installations of the Product;
• Damage or failure of the Product to perform during power failures and interrupted or inadequate
electrical service;
• Damage or failure caused by leaky or broken water pipes, frozen water pipes, restricted drain lines,
inadequate or interrupted water supply or inadequate supply of air;
• Damage or failure resulting from operating the Product in a corrosive atmosphere or contrary to the
instructions outlined in the Product’s owner’s manual;
• Damage or failure to the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, acts
of God, or any other causes beyond the control of LGECI or the manufacturer;
• Damage or failure resulting from misuse, abuse, improper installation, repair, or maintenance of the
Product. Improper repair includes use of parts not authorized or specified by LGECI. Improper
installation or maintenance includes installation or maintenance contrary to the Product’s owner’s
manual;.
• Damage or failure caused by unauthorized modification or alteration of the Product, or if used for other
than the intended household purpose/use of the Product, or damage or failure resulting from any water
leakage due to improper installation of the Product;
• Damage or failure caused by incorrect electrical current, voltage or plumbing codes;
• Damage or failure caused by use that is other than normal household use, including, without limitation,
commercial or industrial use, including use in commercial offices or recreational facilities, or as
otherwise outlined in the Product’s owner’s manual;
• Damage or failure caused by the use of any accessories, components or cleaning products, including,
without limitation, water filters, that are not approved/authorized by LGECI;
• Replacement of the water filter cartridge due to water pressure that is outside the specified operating
range or due to excessive sediment in the water supply;
• Damage or failure caused by transportation and handling, including scratches, dents, chips and/or other
damage to the finish of the Product, unless such damage results from defects in materials or
workmanship and is reported to LGECI within one (1) week of delivery of the Products;
• Damage or missing items to any display, open box, refurbished or discounted Product;
• Refurbished Product or any Product sold “As Is”, “Where Is”, “With all Faults”, or any similar disclaimer;
• Products with original serial numbers that have been removed, altered or cannot be readily determined
at the discretion of LGECI;
• Increases in utility costs and additional utility expenses in any way associated with the Product;
• Any noises associated with normal operation of the Product;
• Replacement of light bulbs, filters, fuses or any other consumable parts;
• Replacement of any part that was not originally included with the Product;
• Costs associated with removal and/or reinstallation of the Product for repairs; and
• Shelves, door bins, drawers, handle and accessories to the Product, except for internal/functional parts
covered under this Limited Warranty.
• Coverage for "in Home" repairs, for products in-warranty, will be provided if the Product is within a 150
km radius from the nearest authorized service center (ASC), as determined by LG Canada. If your Product
is located outside a 150 km radius from a ASC, as determined by LG Canada, it will be your responsibility
to bring the Product, at your sole expense, to the ASC for in-warranty repair.
All costs and expenses associated with the above excluded circumstances, listed under the heading,
This Limited Warranty Does Not Cover, shall be borne by the consumer.
TO OBTAIN WARRANTY SERVICE AND ADDITIONAL INFORMATION, PLEASE CALL OR VISIT OUR WEBSITE:
Call 1-888-542-2623 (7 A.M. to 12 A.M., 365 days a year) and select the appropriate option from the menu,
or visit our website at http://www.lg.com
LIMITED WARRANTY 61
PROCEDURE FOR RESOLVING DISPUTES:
EXCEPT WHERE PROHIBITED AT LAW, ALL DISPUTES BETWEEN YOU AND LG ARISING OUT OF OR RELATING
IN ANY WAY TO THIS LIMITED WARRANTY OR THE PRODUCT SHALL BE RESOLVED EXCLUSIVELY THROUGH
BINDING ARBITRATION, AND NOT IN A COURT OF GENERAL JURISDICTION. EXCEPT WHERE PROHIBITED
AT LAW, YOU AND LG BOTH IRREVOCABLY AGREE TO WAIVE THE RIGHT TO A JURY TRIAL AND TO BRING
OR PARTICIPATE IN A CLASS ACTION.
Definitions. For the purposes of this section, references to “LG” mean LG Electronics Canada, Inc., its
parents, subsidiaries and affiliates, and each of their officers, directors, employees, agents, beneficiaries,
predecessors in interest, successors, assigns and suppliers; references to “dispute” or “claim” shall include
any dispute, claim or controversy of any kind whatsoever (whether based in contract, tort, statute,
regulation, ordinance, fraud, misrepresentation or any other legal or equitable theory) arising out of or
relating in any way to the sale, condition or performance of the product or this Limited Warranty.
Notice of Dispute. In the event you intend to commence an arbitration proceeding, you must first notify
LG in writing at least 30 days in advance of initiating the arbitration by sending a letter to LGECI Legal
Team at 20 Norelco Drive, North York, Ontario, Canada M9L 2X6 (the “Notice of Dispute”). You and LG
agree to engage in good faith discussions in an attempt to amicably resolve your claim. The notice must
provide your name, address, and telephone number; identify the product that is the subject of the claim;
and describe the nature of the claim and the relief being sought. If you and LG are unable to resolve the
dispute within 30 days of LG’s receipt of the Notice of Dispute, the dispute shall be resolved by binding
arbitration in accordance with the procedure set out herein. You and LG both agree that, during the
arbitration proceeding, the terms (including any amount) of any settlement offer made by either you or LG
will not be disclosed to the arbitrator until the arbitrator determines the dispute.
Agreement to Binding Arbitration and Class Action Waiver. Upon failure to resolve the dispute during
the 30 day period after LG’s receipt of the Notice of Dispute, you and LG agree to resolve any claims
between you and LG only by binding arbitration on an individual basis, unless you opt out as provided
below, or you reside in a jurisdiction that prevents full application of this clause in the circumstances of the
claims at issue (in which case if you are a consumer, this clause will only apply if you expressly agree to the
arbitration). To the extent permitted by applicable law, any dispute between you and LG shall not be
combined or consolidated with a dispute involving any other person’s or entity’s product or claim. More
specifically, without limitation of the foregoing, except to the extent such a prohibition is not permitted at
law, any dispute between you and LG shall not under any circumstances proceed as part of a class or
representative action. Instead of arbitration, either party may bring an individual action in small claims
court, but that small claims court action may not be brought on a class or representative basis except to
the extent this prohibition is not permitted at law in your province or territory of jurisdiction as it relates to
the claims at issue between you and LG.
Arbitration Rules and Procedures. To begin arbitration of a claim, either you or LG must make a written
demand for arbitration. The arbitration will be private and confidential, and conducted on a simplified and
expedited basis before a single arbitrator chosen by the parties under the provincial or territorial
commercial arbitration law and rules of the province or territory of your residence. You must also send a
copy of your written demand to LG at LG Electronics, Canada, Inc., Attn: Legal Department- Arbitration, 20
Norelco Drive, North York, Ontario M9L 2X6. This arbitration provision is governed by your applicable
provincial or territorial commercial arbitration legislation. Judgment may be entered on the arbitrator’s
award in any court of competent jurisdiction. All issues are for the arbitrator to decide, except that, issues
relating to the scope and enforceability of the arbitration provision and to the arbitrability of the dispute
are for the court to decide. The arbitrator is bound by the terms of this provision.
Governing Law. The law of the province or territory of your purchase shall govern this Limited Warranty
and any disputes between you and LG except to the extent that such law is preempted by or inconsistent
with applicable federal or provincial/territorial law. Should arbitration not be permitted for any claim,
action, dispute or controversy between you and LG, you and LG attorn to the exclusive jurisdiction of the
courts of the province or territory of your purchase for the resolution of the claim, action, dispute or
controversy between you and LG.
Fees/Costs. You do not need to pay any fee to begin an arbitration. Upon receipt of your written demand
for arbitration, LG will promptly pay all arbitration filing fees unless you seek more than $25,000 in
damages, in which case the payment of these fees will be governed by the applicable arbitration rules.
Except as otherwise provided for herein, LG will pay all filing, administration and arbitrator fees for any
arbitration initiated in accordance with the applicable arbitration rules and this arbitration provision. If you
prevail in the arbitration, LG will pay your attorneys’ fees and expenses as long as they are reasonable, by
62 LIMITED WARRANTY
considering factors including, but not limited to, the purchase amount and claim amount. Notwithstanding
the foregoing, if applicable law allows for an award of reasonable attorneys’ fees and expenses, an
arbitrator can award them to the same extent that a court would. If the arbitrator finds either the
substance of your claim or the relief sought in the demand is frivolous or brought for an improper purpose
(as measured by the applicable laws), then the payment of all arbitration fees will be governed by the
applicable arbitration rules. In such a situation, you agree to reimburse LG for all monies previously
disbursed by it that are otherwise your obligation to pay under the applicable arbitration rules. Except as
otherwise provided for, LG waives any rights it may have to seek attorneys’ fees and expenses from you if
LG prevails in the arbitration.
Hearings and Location. If your claim is for $25,000 or less, you may choose to have the arbitration
conducted solely (1) on the basis of documents submitted to the arbitrator, (2) through a telephonic
hearing, or (3) by an in-person hearing as established by the applicable arbitration rules. If your claim
exceeds $25,000, the right to a hearing will be determined by the applicable arbitration rules. Any in-
person arbitration hearings will be held at the nearest, most mutually-convenient arbitration location
available within the province or territory in which you reside unless you and LG both agree to another
location or agree to a telephonic arbitration.
Severability and Waiver. If any portion of this Limited Warranty (including these arbitration procedures)
is unenforceable, the remaining provisions will continue in full force and effect to the maximum extent
permitted by applicable law. Should LG fail to enforce strict performance of any provision of this Limited
Warranty (including these arbitration procedures), it does not mean that LG intends to waive or has waived
any provision or part of this Limited Warranty.
Opt Out. You may opt out of this dispute resolution procedure. If you opt out, neither you nor LG can
require the other to participate in an arbitration proceeding. To opt out, you must send notice to LG no
later than 30 calendar days from the date of the first consumer purchaser’s purchase of the product by
either (i) sending an e-mail to [email protected], with the subject line: “Arbitration Opt Out;” or (ii) calling 1-
800-980-2973. You must include in the opt out e-mail or provide by telephone: (a) your name and address;
(b) the date on which the product was purchased; (c) the product model name or model number; and (d)
the serial number (the serial number can be found (i) on the product; or (ii) online by accessing https://
Number”).
In the event that you “Opt Out”, the law of the province or territory of your residence shall govern this
Limited Warranty and any disputes between you and LG except to the extent that such law is preempted
by or inconsistent with applicable federal or provincial/territorial law. Should arbitration not be permitted
for any claim, action, dispute or controversy between you and LG, you and LG agree to attorn to the
exclusive jurisdiction of the courts of the province or territory of your residence for the resolution of the
claim, action, dispute or controversy between you and LG.
You may only opt out of the dispute resolution procedure in the manner described above (that is, by e-mail
or telephone); no other form of notice will be effective to opt out of this dispute resolution procedure.
Opting out of this dispute resolution procedure will not affect the coverage of the Limited Warranty in any
way, and you will continue to enjoy the full benefits of the Limited Warranty. If you keep this product and
do not opt out, then you accept all terms and conditions of the arbitration provision described above.
Conflict of Terms. In the event of a conflict or inconsistency between the terms of this Limited Warranty
and the End User License Agreement (“EULA”) in regards to dispute resolution, the terms of this Limited
Warranty shall control and govern the rights and obligations of the parties and shall take precedence over
the EULA.
Memo 63
LG Customer Information Center
For inquiries or comments,
U.S.A.
1-800-243-0000
1-888-542-2623
CANADA
Register your product Online!
|