LG LAC5800R User Manual

LAC5800R_DITALLR_ENG_5348  
ENGLISH  
DEUTSCH  
FRANÇAIS  
ESPAÑOL  
ITALIANO  
MODEL : LAC5800R  
CAUTION : This product uses a Laser System.  
To ensure proper use of this product, please read this owner’s manual carefully  
and retain it for future reference.  
Safety Note  
Should the unit require maintenance, contact an authorized service center.  
Performing controls, adjustments, or carrying out procedures other than those  
specified herein may result in hazardous radiation exposure.  
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible  
laser radiation when open. DO NOT STARE INTO BEAM.  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION : TO REDUCE THE RISK OF ELECTRIC  
SHOCK DO NOT SPLIT COVER(OR BACK) NO USER  
SERVICEABLE PARTS INSIDE. REFER SERVICING  
TO QUALIFIED SERVICE PERSONNEL.  
This lightning flash with arrowhead symbol within an equilateral triangle is  
intended to alert the user to the presence of uninsulated dangerous voltage  
within the product’s enclosure that may be of sufficient magnitude to consti-  
tute a risk of electric shock to persons.  
Disposal of your old appliance  
1. When this crossed-out wheeled bin symbol is attached to a product it  
means the product is covered by the European Directive 2002/96/EC.  
2. All electrical and electronic products should be disposed of separately  
from the municipal waste stream via designated collection facilities  
appointed by the government or the local authorities.  
The exclamation point within an equilateral triangle is intended to alert the  
user to the presence of important operating and maintenance (servicing)  
instructions in the literature accompanying the product.  
Always operate the vehicle in a safe manner.  
3. The correct disposal of your old appliance will help prevent potential  
negative consequences for the environment and human health.  
4. For more detailed information about disposal of your old appliance,  
please contact your city office, waste disposal service or the shop where  
you purchased the product.  
Do not become distracted by the vehicle while driving, and always be fully  
aware of all driving condition. Do not change settings, or any functions.  
Pull over in a safe and legal manner before attempting such operations.  
Do not use for many hours at extremely low or high temperature.  
(-10~60°C)  
To reduce the risk of electric shock, do not remove the cover or back of  
this product. There are no user-serviceable parts inside.  
Refer servicing to qualified service personnel.  
Caution  
When being connected in a wrong way, the unit displays as follows.  
1. Antenna port short : “ANTENNA ON PORT SHORT CIRCUIT CHECK”  
2. Remote port short : “REMOTE ON PORT SHORT CIRCUIT CHECK”  
3. Antenna port and Remote port short : “ANTENNA REMOTE ON PORT  
SHORT CIRCUIT CHECK”  
To reduce the risk of fire or electric shock, do not expose this product to  
dripping or splashing water, rain, or moisture.  
The temperature of unit’s outside can be extremely high, please use the  
unit after proper installation in your vehicle.  
After connecting it again, restart the unit.  
8 cm  
This unit cannot play 8cm disc (use 12cm disc only).  
You have to set the disc format option to [Mastered] in order to make the  
discs compatible with the LG players when formatting rewritable discs.  
When setting the option to Live File System, you cannot use it on LG players.  
(Mastered/Live File System : Disc format system for Windows Vista)  
CAR CD/MP3/WMA Receiver  
3
Front Panel / Remote Control(optional)  
1
2
3
10  
11  
12  
INT  
4
5
+
6
7
13  
14  
8
15  
16  
9
1
2
3
SOURCE [SRC]  
9
ꢀ [BAND]  
ꢀ DRIVE [DRV]  
10 Eject Z  
1
2
3
4
5
6
7
Power [POWER] / Mute  
Select [MENU/SEL]  
Source [SRC]  
Skip / Search / Seek / Tune -?b / B?+  
ꢀ Auto Store [U/AS]  
ꢀ Preset Scan [uu/PS]  
ꢀ MP3/WMA Track +10/-10 U/uu  
ꢀ Folder Up/Down UU/u  
ꢀ Volume  
11 Release  
12 USB slot  
10 Volume Up  
11 Number [#]  
12 Repeat [RPT]  
13 Number [0 -9]  
/ Down  
13 AUX in  
Play / Pause B/X  
Intro Scan [INT]  
14 Preset Station [1~6]  
15 Shuffle [SHF]  
16 Repeat [RPT]  
17 Intro Scan [INT]  
18 Play/Pause B/X  
19 ꢀ [BAND]  
Shuffle [SHF]  
4
14 ꢀ CD Skip / Search  
ꢀ Seek / Tune M M?  
15 Display [DISP.]  
ꢀ MP3/WMA Track +10  
ꢀ Folder Up U  
ꢀ [MUTE]  
ꢀ Power [PWR]  
5
6
7
Remote Sensor (Optional)  
[MENU]  
8
ꢀ CD Skip / Search  
ꢀ Seek / Tune ?m m  
16 ꢀ MP3/WMA Track -10  
ꢀ Folder Down u  
ꢀ [DRIVE]  
ꢀ Equalizer [EQ]  
20 Select [SEL]  
ꢀ Extreme Dynamic Sound System  
[XDSS+]  
8
9
ꢀ Traffic Announcement [TA]  
ꢀ Programme Type [PTY]  
Display [DISP]  
4
CAR CD/MP3/WMA Receiver  
About Detachable Control Panel  
Attaching the control panel  
Detaching the control panel  
1
Align the left side of the panel with  
the stopper.  
Push the right side or panel into the  
unit until it clicks.  
1
Press the “  
open the control panel.  
Hold the right part of the control  
panel.  
” (RELEASE) to  
2
1
2
3
4
Pull out the control panel.  
Place the control panel in the  
supplied protective case.  
2
2
3
1
Caution  
The control buttons may not work properly if the control panel is not attached  
properly. If this occurs, gently press the display.  
4
Do not leave the control panel in any area exposed to high temperatures or  
direct sunlight.  
Do not drop the control panel or otherwise subject it to strong impact.  
Do not allow such volatile agents as benzine, thinner, or insecticides to come  
into contact with the surface of the control panel.  
Control panel  
Protective Case  
Note  
Periodically wipe the contacts on the back of the control  
panel with a cotton swap moistened with alcohol. For safety,  
turn off the ignition before cleaning, and remove the key  
from the ignition switch.  
CAR CD/MP3/WMA Receiver  
5
Installation  
ISO-DIN Installation  
Basic Installation  
1
2
3
4
Slide the unit into the ISO-DIN  
frame.  
Fit screws removed from the old  
unit.  
Slide the unit and frame into the  
dash opening.  
Install the dash panel or adapter  
plate.  
Before installing, make sure that the  
ignition-switch is set to OFF and  
remove the terminal of the car battery  
to avoid short-circuiting.  
Bend the claws  
according to  
the thickness  
of the  
dashboard  
1
2
4
1
2
3
4
Remove the existing receiver unit.  
Make the necessary connections.  
Install the installation sleeve.  
Install the unit into the installation  
sleeve.  
3
5
6
5
6
Install the trim ring to the unit.  
Install the control panel to the unit.  
Control panel  
Control panel  
Battery Installation  
1
Pull out the battery holder with a  
sharp product like a ball point pen.  
Removing the existing receiver unit  
2
3
Put the battery with  
rectly on the battery holder.  
Push the battery holder back into its  
original position.  
and  
cor-  
If there is already an installation  
sleeve for the receiver unit in the  
dashboard, it must be removed.  
A
1
2
3
Remove the rear support from the  
unit.  
Remove the control panel and trim  
ring from the unit.  
A
Insert the lever A into the hole on  
one side of the unit.  
Note  
ꢀ Use only one CR2025 (3V) lithium battery.  
ꢀ Remove the battery if the remote control is not used for a long period of  
time.  
Perform the same operation on  
the other side and pull the unit out  
from the mounting sleeve.  
ꢀ Do not leave the product in a hot or humid place.  
ꢀ Do not handle the battery with metallic tools.  
ꢀ Do not store the battery with metallic materials.  
6
CAR CD/MP3/WMA Receiver  
Connection  
Before connecting, make sure that the ignition switch is set to OFF, and remove the battery # terminal to avoid short circuits.  
1
2
3
4
5
6
7
8
B
Phone Mute(Orange)  
1
2
3
4
5
6
7
8
A
Remote On(Blue/White)  
Amplifier  
(Optional)  
Amplifier  
(Optional)  
Front Left  
Front Right  
Rear Left  
Rear Right  
To Audio out  
To Audio in  
Power  
Antenna  
Control Relay  
A 5  
Power Antenna(Blue)  
A 6  
Dimmer(Pink)  
Dimmer Switch  
Ignition Switch  
A 7  
To Ignition(Red)  
B 1 Violet : Rear Right +  
B 2 Violet/ Black Stripe : Rear Right –  
B 3 Gray : Front Right +  
B 4 Gray / Black Stripe : Front Right –  
B 5 White : Front Left +  
B 6 White/Black Stripe : Front Left –  
B 7 Green : Rear Left +  
B 8 Green/ Black Stripe : Rear Left –  
A 4  
To Battery(+)(Yellow)  
B
1
2
B
A 8  
Ground(-)(Black)  
B
B
B
B
B
B
3
4
5
6
7
8
BATTERY  
A1, A2, A3 : Not connected  
CAR CD/MP3/WMA Receiver  
7
Basic Operation  
When EQ and XDSS+ is set to “Off”, you can adjust the sound level (BAS, MID,  
TRB) settings.  
ON PLAYER  
PWR/MUTE  
SRC  
ON REMOTE  
POWER  
1. Turn the unit on.  
2. Select a source.  
3. Adjust the volume.  
XDSS+ (Extreme Dynamic Sound System)  
SRC  
Press and hold EQ/XDSS+. (XDSS+ : Improves the treble, bass sound.) To can-  
cel it, press and hold again.  
Rotate PWR  
VOLUME  
Checking the clock  
You can see the clock pressing DISP (DISP. on the remote control)..  
Basic operation - more you can do  
Mute  
Listening RDS broadcasting  
Press MUTE/PWR (POWER  
cancel it, press again.  
on the remote control) to cut the sound. To  
ON PLAYER  
Changing the general settings  
1. Select a source to tuner.  
2. Select a band to FM.  
SRC  
1 Press MENU (press and hold SEL/MENU on remote control) so that one of  
menu items appears.  
2 Press MENU (SEL/MENU on remote control) and rotate PWR. (Press VOL-  
BAND  
Press and hold TA/PTY  
1-6  
3. Select a programme types.  
4. Select a station in PTY type.  
UME  
on the remote control.) to select one of the settings specified  
belows.  
- For more details about setting information, refer to page 12 .  
3 Press and hold MENU (SEL/MENU on remote control) to finish the setting.  
RDS broadcasting information.  
Press and hold the PTY repeatedly for selecting each mode.  
Music group t Speech Group t Search off  
Using the EQ  
NO. MUSIC GROUP  
NO. SPEECH GROUP  
EQ is to increase or decrease the signal strength of audio frequencies. The func-  
tion helps you to enjoy sound more plentifully. Press EQ/XDSS+ repeatedly. The  
indicator lights up in the following order.  
1. POP M, ROCK M  
2. EASY M, LIGHT M.  
3. CLASSICS, OTHER M  
4. JAZZ, COUNTRY  
5. NATION M, OLDIES  
6. FOLK M  
1. NEWS, AFFAIRS, INFO  
2. SPORT, EDUCATE, DRAMA  
3. CULTURE, SCIENCE, VARIED  
4. WEATHER, FINANCE, CHILDREN  
5. SOCIAL, RELIGION, PHONE IN  
6. TRAVEL, LEISURE, DOCUMENT  
Pop t Classic t Rock t Jazz t Vocal t Salsa t Samba t User1 t  
User2 t Off  
Note  
When XDSS+ is set to “Off”, you can adjust the EQ settings.  
Adjusting the sound level  
Press SEL (SEL/MENU on the remote control) repeatedly to select the mode  
you want to adjust from volume, balance and fader. To adjust sound quality,  
rotate PWR.  
Note  
8
CAR CD/MP3/WMA Receiver  
Listening to the radio  
Connecting USB device  
ON PLAYER  
SRC  
ON REMOTE  
SRC  
1. Select a source to tuner.  
2. Select a band.  
BAND  
3
/
BAND  
3. Auto seek.  
Manual seek.  
-?b / B?+  
Press and hold  
-?b / B?+  
?mm/MM?  
Press and hold  
?mm/MM?  
ON PLAYER  
ON REMOTE  
1. Open the USB cover.  
2. Connect the USB device.  
3. Adjust the volume.  
-
-
-
Listening to the radio - more you can do  
-
Rotate PWR  
VOLUME  
Auto search memory  
Press U/AS. The six strongest broadcast frequencies will be stored under preset  
Moving to another drive  
button 1-6 in the order of their signal strength.To cancel, press U/AS.  
When connecting this unit to multi reader, press BAND/DRIVE (BAND/DRV on  
remote control) to go to the next drive. Each time you press the button, the driv-  
er modes changes.  
Storing and recalling broadcast frequencies  
1 Press BAND to select desired band you want to store.  
2 Select the desired frequency and press one of preset buttons 1-6 and hold  
until the beep sound.  
3 Repeat steps 1-2 to preset other stations.The next time, you press the same  
preset button, the radio station frequency is recalled from the memory.  
Note  
If the USB device is already connected, press SRC (SRC on remote control.) to  
select a source to USB.  
Connecting an Auxiliary Equipment  
To scan the preset stations  
Press uu/PS. Each preset station appears. To cancel, press u/PS.  
Auxiliary input  
To tune in the preset stations  
Press BAND to select the desired band and press the desired preset button 1-6  
(preset button 1-6 on the remote control).  
Note  
Line out  
MP3 Player, etc  
When a station is stored on the preset numbers on which another station of the  
same band has already been preset, the previously preset station is automati-  
cally erased.  
ON PLAYER  
ON REMOTE  
1. Select a source to AUX.  
SRC  
-
SRC  
-
2. Play the connected Auxiliary  
Equipment.  
3. Adjust the volume.  
Rotate PWR  
VOLUME  
CAR CD/MP3/WMA Receiver  
9
Note  
Listening a CD  
During random playback, if you press -?b , you won’t go back to the previous  
track.  
ON PLAYER  
-
ON REMOTE  
-
1. Insert a CD.  
MP3/WMA Track -10 / +10  
Rotate PWR  
2. Adjust the volume.  
VOLUME  
(If there is no folder or one folder.) During playback press u/PS to go back 10  
tracks, and press U//AS to go forward 10 tracks.  
Listening a CD - more you can do  
MP3/WMA Folder UP/DOWN  
(If there are more than two folders.) During playback, press u/PS to go back to  
Pause or restart a CD  
the previous folder, and press UU/AS to go forward to the next folder.  
Press  
on the player (  
/ on the remote control) during playback. Press this  
B
[]  
B
[]  
button again to resume play.  
See information about your music  
Search for a section within a track / file  
MP3/WMA files often come with tags. The tag gives the Title, Artist or Album.  
Press DISP repeatedly during MP3/WMA/CD TEXT file playback. If there is no  
information, “NO TEXT” will be shown in the display window.  
Press and hold -?b / B?+ on the player (.bb/BB> on remote control) for  
about 1 second during playback and then release at the point you want.  
Note  
Skip to another track / file  
: The icon is displayed during MP3/WMA playback.  
ꢀ MP3/WMA Disc compatibility with this unit is limited as follows:  
1. Sampling Frequency / 8 - 48kHz (MP3) 22.05 - 48kHz (WMA)  
2. Bit rate / within 8 - 320kbps (include VBR) (MP3) 32 -320kbps (WMA)  
3. CD-R/CD-RW file system should be “ISO 9660”  
Press -?b / B?+ on the player (.bb/BB> on remote control.). To skip to  
previous track, press briefly -?b within 3 seconds of playing time. Press [#] and  
a number you want to move on remote control to move the files/track.  
4. If you record MP3/WMA files using software which cannot create a FILE  
SYSTEM, for example “Direct-CD” etc., it will not be possible to playback  
MP3/WMA files. We recommend that you use “Easy-CD Creator” which cre-  
ates an ISO9660 file system.  
Intro scan  
Press or press and hold INT on the player (INT on remote control). Each files in  
the current selected folder (  
INT) or the first 10 seconds of each tracks/files  
5. WMA decoder is supported until “Class 2A”.  
(INT) on the disc are played. To cancel it, press the button again.  
Customers should also note that permission is required in order to down-  
load MP3/WMA files and music from the Internet. Our company has no  
right to grant such permission. Permission should always be sought from  
the copyright owner.  
Repeat  
Press or press and hold RPT on the player (RPT on the remote control). The  
current selected tracks/files (1 RPT) or folder (  
RPT) on the disc is played  
repeatedly. To cancel it, press the button again.  
Shuffle  
Press or press and hold SHF on the player (SHF on the remote control). Each  
files in the current selected folder ( SHF) or all of the tracks/files (SHF) on  
the disc is played randomly. Press SHF again to cancel it.  
10 CAR CD/MP3/WMA Receiver  
Troubleshooting  
Symptom  
Cause  
Correction  
Power doesn’t turn on / The Leads and connectors are not properly.  
unit doesn’t operate.  
Confirm once more that all connections are  
correct.  
General  
The fuse is blown.  
Rectify the problem that caused the fuse to  
blow, and then replace it. Be very sure to  
install the correct fuse with the same rate.  
Noise and other factors are causing the built- Turn the unit off and then on.  
in microprocessor to operate incorrectly.  
No sound is heard / The vol- Cables are not connected correctly.  
ume level will not rise.  
Connect the cables correctly.  
There’s audio skipping.  
The playback is not possi  
ble.  
This unit is not firmly secured.  
The disc is dirty.  
Secure this unit firmly.  
Clean disc.  
CD  
The loaded disc is of a type this unit cannot  
play.  
Check what type the disc.  
Battery power is low.  
The unit does not operate  
correctly even when the  
appropriate remote  
Load new battery.  
Remote  
control buttons are pressed.  
CAR CD/MP3/WMA Receiver 11  
Specifications  
General setting information  
z AF(Alternative frequency) ON / OFF  
General  
When the reception quality drops, the tuner automatically changes to anoth-  
er station in the network, broadcasting a better reception quality, using the  
PI and AF codes.  
Output Power  
Power Source  
Speaker impedance  
Ground System  
Dimensions (W x H x D)  
Net Weight  
Tuner  
FM  
Frequency Range  
S/N Ratio  
50W x 4CH (Max.)  
DC 12V  
4  
Negative  
180 x 50 x 176 mm (Without Control Panel)  
1.3 kg  
z REG (Region) ON / OFF  
REG ON : The unit switches to another station, within the same network,  
broadcasting the same program when the receiving signals from the current  
station become weak.  
REG OFF : The unit switches to another station, within the same network  
when the receiving signals from the current station become weak. (This  
mode, the program may differ from the one currently received.)  
z TA(Traffic Announcement) ALARM / SEEK  
87.5-107.9, 87.5-108, 65-74 or 87.5-108 MHz  
55 dB  
Distortion  
0.7%  
TA ALARM : When a newly tuned station has no TP information for 5 sec-  
onds, a double beep sound is output.  
Usable Sensitivity  
AM (MW)  
Frequency Range  
S/N Ratio  
12 dBµV  
TA SEEK : When the newly tuned station does not receive TP information  
for 5 seconds, the receiver retunes to the next station which has the same  
PI as the last station, but has the TP information.  
520-1720 or 522-1620 kHz  
50 dB  
1.0%  
z PI (Programme Identification) SOUND / MUTE  
Distortion  
PI SOUND : If the sound of a station with different PI is heard intermittently,  
the receiver mutes the sound after 1 second. PI MUTE : If the sound of a  
station with different PI is heard intermittently, the receiver mutes the sound  
right now.  
Usable Sensitivity  
CD  
Frequency Response  
S/N Ratio  
Distortion  
Channel Separation (1kHz) 55 dB  
28 dBµV  
20 Hz-20 kHz  
80 dB  
0.12%  
z AUX (Auxiliary) ON / OFF  
It is possible to use auxiliary equipment with this unit. Activate the auxiliary  
setting when using auxiliary equipment connected to this unit.  
z AUX (Auxiliary) 00dB / +6dB  
You can adjust the volume level of each source to prevent radical changes  
in volume when switching between sources.  
AUX  
Frequency Response  
S/N Ratio  
20 Hz-20 kHz  
80 dB  
Distortion  
Channel Separation (1kHz) 45 dB  
Max Input Level (1kHz)  
0.12 %  
You can set to 0 dB or +6 dB. You may be surprised at a loud sound when  
you change the source from the external component to another source.  
z DEMO OFF/ ON  
1.2V (35K)  
You can change the initial indication on the display to information name  
(function name, EQ name, etc...) while listen to a source.  
z LED RED / GRN  
Designs and specifications are subject to change without notice.  
You can change the color of button. RED(red) <-> GRN(green)  
z BEEP 2ND / ALL  
BEEP 2ND : The beep is generated when a key is long pressed. (1 sec)  
BEEP ALL : The beep is generated when any key is pressed.  
P/N : MFL41655348  
12 CAR CD/MP3/WMA Receiver  

Toshiba Air Conditioner Rav Sm406bt Tr User Manual
Sony Up Dr80md User Manual
Sharp Plasmacluster Air Purifier Replacement Filter Set Fzr65hfu User Manual
Sharper Image Si871 User Manual
Sanyo Stb1023c1 User Manual
Oki Fax 5980 User Manual
LG G4 LG H815T User Manual
KENWOOD KVT 522DVDY User Manual
FUJITSU UTG CCGF User Manual
FUJITSU SCANSNAP S1100 02 User Manual