LG CORDZERO A9 User Manual

OWNER'S MANUAL  
VACUUM CLEANER  
Read this owner's manual thoroughly before operating the  
appliance and keep it handy for reference at all times.  
ENGLISH  
A9********  
MFL69883677  
Rev.02_090121  
Copyright © 2021 LG Electronics Inc. All Rights Reserved.  
IMPORTANT SAFETY INSTRUCTIONS  
3
IMPORTANT SAFETY INSTRUCTIONS  
READ ALL INSTRUCTIONS BEFORE USE  
Safety Messages  
Your safety and the safety of others are very important.  
We have provided many important safety messages in this manual and on your appliance. Always read and  
follow all safety messages.  
This is the safety alert symbol.  
This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages  
will follow the safety alert symbol and either the word WARNING or CAUTION.  
These words mean:  
WARNING  
You may be killed or seriously injured if you do not follow instructions.  
CAUTION  
You may be injured or cause damage to the product if you do not follow instructions.  
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,  
and tell you what may happen if the instructions are not followed.  
WARNING STATEMENTS  
WARNING  
• To reduce the risk of explosion, fire, death, electric shock, injury or scalding to persons when using this  
product, follow basic precautions, including the following:  
Technical Safety  
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or  
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or  
instruction concerning use of the appliance by a person responsible for their safety.  
• Do not allow the appliance to be used as a toy. Close attention is necessary when used by or near  
children.  
• Do not allow children to play with or hang on the appliance.  
• Do not use the appliance with a damaged power cord or plug. The cord must be replaced. If the  
appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water,  
return it to an LG Electronics service center.  
• Do not pull or carry by the cord, use the cord as a handle, close a door on the cord, or pull the cord  
around sharp edges or corners. Do not run the appliance over the cord. Keep the cord away from heated  
surfaces.  
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.  
• Place the cords from other appliances out of the area to be cleaned.  
• Have servicing performed by a qualified repair person using only identical replacement parts. This will  
ensure that the safety of the product is maintained.  
     
4
IMPORTANT SAFETY INSTRUCTIONS  
Battery  
• Never use the battery, adapter, and the charging station from other appliances with this appliance. Use  
only the battery and the charging station provided by LG Electronics.  
• Use appliances only with specifically designated battery packs. Use of any other battery packs may  
create a risk of injury and fire.  
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of  
battery pack may create a risk of fire when used with another battery pack.  
• Never use the battery, adapter, and the charging station from this appliance with other appliances.  
• Unplug the power cord and remove the battery if the appliance will not be used for an extended period  
of time.  
• Do not use modified or damaged batteries.  
• When disposing of the battery or the appliance, remove the battery from the appliance and safely  
dispose of it.  
• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may  
exhibit unpredictable behavior resulting in fire, explosion or risk of injury.  
• Do not disassemble, remove or short-circuit the battery.  
• Have the battery replaced when it is no longer able to hold a charge.  
• Refer to the Charging the Battery section instructions for the method of replacing the battery.  
• When disposing of this appliance, follow regulations for disposal of rechargeable lithium-ion batteries.  
• Follow all local ordinances and regulations when handling or disposing of the battery.  
• Disconnect the battery pack before cleaning or servicing.  
• Prevent unintentional starting. Ensure the switch is in the off position before connecting to the battery  
pack, picking up or carrying the appliance. Carrying the appliance with your finger on the switch or  
energizing an appliance that has the switch on invites accidents.  
• Disconnect the battery pack from the appliance before making any adjustments, changing accessories,  
or storing appliance. Such preventive safety measures reduce the risk of starting the appliance  
accidentally.  
• When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys,  
nails, screws or other small metal objects, that can make a connection from one terminal to another.  
Shorting the battery terminals together may cause burns or a fire.  
• Under abusive conditions, liquid may be ejected from the battery. If this happens, avoid contact. If  
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.  
Liquid ejected from the battery may cause irritation or burns.  
• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated  
in the instructions for use and care.  
Battery Specifications  
• One or two batteries are provided. The number of batteries varies depending on the model purchased.  
- Model Name: EAC63382204  
- Type: Rechargeable Lithium-ion Battery  
- Rated Capacity: DC 25.2 V, 2.4 Ah/60.48 Wh(Min. 2.3 Ah/57.96 Wh)  
Installation  
• To avoid an electrical shock or fire, do not install, charge or store the appliance where it may be exposed  
to water, rainfall or high humidity.  
• Install, charge and store the appliance in a well-ventilated place.  
IMPORTANT SAFETY INSTRUCTIONS  
5
• Avoid operating the appliance in areas where there is a risk of leakage of flammable gas, industrial oil or  
metallic dust.  
• Do not store or install the appliance, power cord or plug near heating devices or open flames.  
• Install the charging station on a firm, level surface.  
• Do not use or store the appliance at temperatures below 41 °F (5°C) or above 100 °F (38°C).  
• Do not store or install the appliance where it is exposed to temperatures below freezing or exposed to  
outdoor weather conditions.  
• When installing or moving the appliance, be careful not to pinch, crush, or damage the power cord or  
plug.  
Operation  
• Use only as described in this manual. Use only manufacturer’s recommended attachment.  
• This appliance is designed for normal indoor domestic use only. It is not to be used for any non-  
residential, commercial, or industrial application.  
• Do not use or store the appliance in any outdoor location, garage environment or on wet surfaces.  
• This product should only be used with a 120 V~ 60 Hz outlet. Make sure to check the power specifications  
of the place where you intend to use the appliance.  
• Do not handle the power cord, plug, or appliance controls with wet hands.  
• Wipe any moisture or dirt off the cord or plug with a dry cloth.  
• Unplug the power cord using the plug, not the cord. Pulling on the cord can damage it and result in  
electric shock or fire.  
• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has  
missing or broken parts, including a damaged cord or plug. Take it to an authorized LG Electronics  
service center or dealer for assistance.  
• Do not apply excessive force to the power cord to bend it, or place it under a heavy object as this will  
damage it.  
• Do not use multiple-outlet adapters with this appliance. Make sure to use a power socket with a capacity  
of 10 A.  
• Do not plug the appliance into a damaged or loose outlet.  
• Make sure to unplug the power cord when the appliance is not to be used for an extended period of  
time.  
• Do not damage, alter, excessively bend, twist, pull, pinch or heat the power cord.  
• Before using the appliance, remove any wire or string on the floor.  
• Avoid touching the prongs of the power plug with your finger(s) when unplugging the power cord.  
• Do not cover the power cord with a rug or carpeting.  
• Push the power plug firmly into the wall outlet so that it is not loose.  
• If the product has been submerged, contact an LG Electronics service center or dealer for instructions  
before resuming use.  
• If the product makes a strange noise or emits an odor or smoke, discontinue use and contact an LG  
Electronics customer information center.  
• Only qualified technicians or service personnel from LG Electronics may disassemble, repair or modify  
the appliance.  
• Never insert a sharp metal object such as a pin, nail or knife in a hole or gap in the appliance or the  
charging station.  
• Do not vacuum liquids with this appliance. Make sure that no water, beverage or detergent gets inside  
the appliance or the charging station.  
• Do not allow the appliance to sweep up blades, thumb tacks, sawdust, sharp objects, or hot or cold  
ashes.  
6
IMPORTANT SAFETY INSTRUCTIONS  
• Do not allow children to use the appliance.  
• Do not let children or pets get close to the appliance when using, charging or storing.  
• Do not insert the nozzle or tools in your mouth.  
• Keep clothing and hair, fingers, or other parts of the body away from openings and moving parts.  
• Do not operate the appliance with the suction inlet or outlet blocked.  
• Do not use in an enclosed space where vapors are present from paint thinner, mothproofing substances,  
flammable dust or other explosive or toxic materials.  
• Make sure that the filter is installed before use.  
• Do not use with the dust bin opened.  
• Do not touch the charging terminals on the appliance or the charging station, or insert an electrified  
object inside the appliance or the station.  
• Always store the appliance on the charging station when it is not in use.  
• Do not lean the appliance on walls, chairs or tables.  
• If the earth leakage breaker is tripped when the product is put on the charging station, immediately  
remove the appliance from the charging station. Contact an LG Electronics customer service center.  
• Use extra care when cleaning on stairs.  
• Do not use or store a heating device or flammable substance (ether, benzene, alcohol, chemicals,  
combustible sprays, insecticide, air freshener or cosmetics) in close proximity to the appliance.  
• Do not attempt to clean up a liquid substance (water, beverage), odorous substances (candy, chocolate,  
pet excrement), metal objects (blades, pins), flammable substances, surfactants, or glass shards with this  
appliance.  
• In the event of a gas leak (natural gas, propane gas, etc.) do not operate this or any other appliance.  
Open a window or door to ventilate the area immediately.  
• Do not hold the charging station upside down with the battery in the charging station.  
• Do not expose the appliance, and the battery in particular, to heat, a heating device or direct sunlight.  
• Do not keep the appliance or its battery inside a vehicle which is exposed to direct sunlight.  
• Never allow any water, beverage or detergent to get inside the battery.  
• Do not apply physical impacts to the battery.  
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair,  
and anything that may reduce airflow.  
• Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they  
may be present.  
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.  
• Do not use the appliance without the dust bin and filters in place.  
Maintenance  
• Make sure to unplug the power cord when cleaning or maintaining the charging station.  
• Do not wash the inlet port or the dust bin with water or detergent.  
• Do not use detergents, polishes or air fresheners to clean the dust bin.  
• Do not spray or use water, inflammable materials such as gasoline or thinners, or surfactants such as  
detergent or bath soap near the appliance.  
• Wash hands after handling nozzles. The nozzles contain carbon fiber, and contact may cause minor skin  
irritation.  
IMPORTANT SAFETY INSTRUCTIONS  
7
Disposal  
• Keep packing materials out of the reach of children. Packaging materials can pose a suffocation risk for  
children.  
• Destroy the carton, plastic bag, and other packing materials after the appliance is unpacked. Children  
might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight  
chambers.  
• Dispose of this appliance according to local, state, and regional laws and regulations.  
• Contact your local city council or the related government authority before disposing of this appliance.  
• In case a rechargeable battery is included in this product, the entire device should be recycled in  
compliance with rechargeable battery recycling standards because of the internal battery. To dispose of  
Mop Nozzle  
• Do not use the mop nozzle to clean up sharp objects such as glass shards, wires, blades, or pins. The  
sharp objects could become embedded in the mop pads and cause injury when you clean the pads.  
8
IMPORTANT SAFETY INSTRUCTIONS  
CAUTION STATEMENTS  
CAUTION  
• To reduce the risk of injury to persons, malfunction, or damage to the product or property when using  
the appliance, follow basic safety precautions, including the following:  
Operation  
• This appliance has a built-in safety device to prevent damage from overheating. If the appliance  
becomes overheated after extended use, it may automatically turn off. If this occurs, leave the appliance  
in a cool, well-ventilated area for about an hour before turning on the power again.  
• Do not subject the product to shocks or drop it.  
• Secure the appliance in the charging station when not in use, to avoid it falling over.  
• Do not install wet or damp filters.  
• Make sure to wipe up any liquid such as water or oil or pet excrement from the floor before using the  
appliance.  
• Do not clean the product with a volatile or organic solvent (thinner or acetone).  
• Always use a soft cloth to clean the appliance.  
• Remain aware of your surroundings while using the appliance to avoid colliding with people or animals.  
• Do not kick or apply force to the appliance.  
• Do not put any object other than the appliance, especially a metallic or magnetic object, on the charging  
station.  
• Do not clean the same spot repeatedly for an extended period of time.  
• Vibration from the inlet port or rotating brush may damage the floor or the carpet.  
• Keep fingers away from pinch points when assembling the appliance or the charging station.  
• Do not let a child or a pet hang onto the charging station.  
• Do not apply force or any impact to the cyclonic mesh filter.  
• Do not remove the battery during operation.  
Mop Nozzle  
• Do not use the mop nozzle for purposes other than domestic floor cleaning. The product is not designed  
for purposes such as polishing a car or cleaning windows.  
• When using the mop nozzle, always attach the mop pads.  
• Do not clean coated, rough or delicate floating floors or any kind of carpet with the mop nozzle.  
• Do not use the mop nozzle to clean the same spot repeatedly for an extended period of time.  
• Do not step on the mop nozzle.  
• Wet floors can pose a slip hazard. Allow floors to dry completely before allowing anyone to walk on  
them.  
• Do not store the appliance with a full water tank attached to the mop nozzle.  
SAVE THESE INSTRUCTIONS  
 
INSTALLATION  
9
INSTALLATION  
Product Overview  
The images in this guide may be different from the actual components and accessories, which are subject  
to change by the manufacturer without prior notice for product improvement purposes.  
NOTE  
• For your safety and for extended product life, use only authorized components. The manufacturer is not  
responsible for product malfunction, property damage or bodily injury caused by the use of separately  
purchased unauthorized components, parts, or non-LG products.  
Front View  
† This feature is only available on some models.  
a Product Body  
b Extension Pipe  
c Nozzle  
d Battery (Dual Battery )  
e Exhaust Filter  
f Pre-filter  
g Kompressor Lever  
h Cyclonic Mesh Filter  
     
10 INSTALLATION  
NOTE  
• Use the vacuum cleaner only with the provided charging station. Using a charging station other than the  
one designed to be used with the vacuum cleaner may result in improper sealing of the product and  
failure to empty dust from the vacuum cleaner.  
INSTALLATION 11  
Tools and Accessory Bag  
Accessories  
† This accessory is only available on some models.  
Included Accessories  
a Hard Dirt Tool  
b Mattress Tool  
c Multi-angle Tool  
d Flexible Crevice Tool  
a Product Body  
b Extension Pipe  
c Pre-filter  
e Flexible Hose Extension  
d Battery (Dual Battery )  
f Accessory Bag  
Basic Accessories  
Mop Kit  
a Combination Tool  
b Crevice Tool  
a Mop Nozzle  
b Mop Pads for General Cleaning  
c Cleaning Brush  
c Water Tank Filler  
Nozzles  
NOTE  
• The mop pads, batteries, exhaust filter and the  
pre-filter will eventually need to be replaced.  
Contact an LG Electronics customer service  
center.  
a Universal Nozzle  
b Slim Hard Floor Nozzle  
c Bedding Nozzle  
d Pet Nozzle  
 
12 INSTALLATION  
Specifications  
Appliance  
Model  
A9**********  
Dimensions  
(Width X Depth X  
Height)  
10.2 in X 10.6 in X 44.1 in  
260 mm X 270 mm x 1120 mm  
Weight  
Approximately 5.95 lb (2.7 kg)  
Power Consumption  
370 W in Turbo Mode (Maximum 590 W)  
120 W in Power Mode  
68 W in Normal Mode  
Battery Run Time  
(Using two battery)  
Using with the Tool  
Using with the Nozzle  
Up to 14 minutes in Turbo Mode  
Up to 60 minutes in Power Mode  
Up to 120 minutes in Normal Mode  
Up to 12 minutes in Turbo Mode  
Up to 40 minutes in Power Mode  
Up to 80 minutes in Normal Mode  
Battery Run Time  
(Using one battery)  
Using with the Tool  
Using with the Nozzle  
Up to 7 minutes in Turbo Mode  
Up to 30 minutes in Power Mode  
Up to 60 minutes in Normal Mode  
Up to 6 minutes in Turbo Mode  
Up to 20 minutes in Power Mode  
Up to 40 minutes in Normal Mode  
• Dimensions are given for the assembled product body, extension pipe and nozzle.  
• Battery run time is the result of using a fully charged battery according to the LG Electronics test  
standard. Results may be different depending on actual use environment and period of use.  
• Recommended maximum run time when using the mop nozzle is 80 minutes. Otherwise, the motor may  
overheat.  
† The Nozzle contains the direct drive motor that rotates the nozzle cleaning head directly.  
Charging Station  
Model  
VDS-ST1****  
Input  
120 V~ 60 Hz  
Output  
DC 28.3 V / 1.15 A  
Power Consumption  
9 A (Cleaning)  
0.6 A (Charging)  
Storing the Accessories  
Assembling and Storing the  
Appliance  
Follow these steps to safely assemble the  
appliance.  
1
Firmly attach the extension pipe c, nozzle d,  
or tool onto the product body a.  
2
Put the product body on the charging station.  
• To detach the extension pipe, press the  
extension pipe release button b.  
• If the vacuum cleaner fits properly inside  
the charging station, the alarm will sound.  
Wait several seconds and if the alarm does  
   
INSTALLATION 13  
not sound, reinsert the vacuum cleaner,  
making sure that the nozzle is horizontal.  
Storage Inside  
1
Open the left door of the product and insert  
the bedding nozzle or the pet nozzle a for  
storage.  
Storing the Tools  
Use the product to store the inlet and components  
provided with the vacuum cleaner.  
2
Open the right door and insert the  
combination tool b, the crevice tool c and  
the cleaning brush d for storage.  
The components may differ depending on the  
vacuum cleaner model.  
Using the Nozzle Hooks  
1
Open the nozzle hook a on both sides of the  
product.  
• To open the nozzle hooks, press on the right  
side. Be careful not to pinch fingers when  
opening.  
NOTE  
• Before moving the product, unplug it and  
remove the vacuum cleaner, nozzles, and  
accessories.  
• To carry the product, open both doors and hold  
the areas shown.  
2
Hang the nozzle on the nozzle hook.  
14 OPERATION  
OPERATION  
• Do not use tools to clean a TV, monitor or LCD  
display as they may scratch these surfaces.  
Getting Started  
Before Using the Appliance  
• Make sure that the exhaust filter and pre-filter  
are properly assembled before using the  
appliance.  
Assembling Attachments  
Nozzles and tools can be attached to either the  
product body or the end of the extension pipe.  
• Close the dust bin cover properly before using  
the appliance. If the dust bin cover is left open,  
the suction strength may deteriorate and affect  
the cleaning performance.  
CAUTION  
• Running the appliance for a long period of time  
with a tool connected may cause the motor to  
overheat.  
• This appliance has a built-in safety device to  
prevent overheating. If the appliance becomes  
overheated after extended use, it may  
automatically turn off. If this occurs, leave the  
appliance in a cool, well-ventilated area for  
about an hour before turning on the power  
again.  
• This appliance has a built-in safety device to  
prevent overheating. If the appliance becomes  
overheated after extended use, it may  
automatically turn off. If this occurs, leave the  
appliance in a cool, well-ventilated area for  
about an hour before turning on the power  
again.  
• Make sure to remove any foreign object such as  
a sock or stocking before using the appliance.  
Any foreign object on the inlet port or extension  
pipe will prevent the appliance from functioning  
properly.  
• Do not use the Kompressor lever while the  
appliance is running. Doing so may cause  
product damage.  
• Environmental conditions such as temperature  
and humidity may cause static electricity to  
accumulate on the appliance. Please contact LG  
Electronics customer information center if the  
problem persists.  
1
Insert the fully charged battery a into the  
cavity at the bottom of the handle on the  
product body.  
• Please use the product at normal room  
temperatures as the battery runtime may  
deteriorate severely if used at temperatures  
lower than 41 °F (5°C) or higher than 100 °F  
(38°C) for an extended period of time.  
• Do not use the appliance to suck up oils or any  
liquids, including water.  
2
Attach the nozzles, tools, or extension pipe by  
sliding them onto the inlet b on the body  
until they click into place. The nozzles and  
tools can also be attached to the end of the  
extension pipe b.  
• Support the bottom of the appliance when  
cleaning an elevated surface.  
• Store the appliance in the charging station or  
place it flat on the floor when not in use. Leaning  
the appliance against a wall or chair can result in  
product damage or personal injury if the  
appliance falls.  
• Detach the accessories by pressing the  
release button c.  
• To avoid scratches on polished floors, keep the  
brushes of the nozzles and tools free from grit,  
sand, or abrasive objects.  
• Refer to the Specifications section for battery  
runtime details.  
• The battery runtime is dependent on the surface  
type and the suction power.  
• Follow manufacturer’s recommendations when  
cleaning flooring, carpets, and rugs.  
   
OPERATION 15  
3
Adjust the extension pipe by pressing the  
length adjustment button d on the back of  
the pipe and sliding until it clicks into place at  
the desired length.  
Display  
The handle of the appliance displays indicators for  
clogged objects, filter cleaning alerts, appliance  
connection status, and the remaining battery  
charge.  
• The extension pipe extends in four steps.  
4
Press the Power button to activate the  
a Clogged Objects Indicator  
Normal mode.  
• This indicator lights up when the interior of  
the product body, extension pipe, inlets,  
nozzle, exhaust filter, pre-filter, or cyclonic  
mesh filter is clogged with foreign objects.  
• To turn off the appliance, press the Power  
button again.  
• If clogging persists, the motor will cycle and  
the appliance will shut off. Remove the  
foreign objects and clean the exhaust filter,  
pre-filter and cyclonic mesh filter following  
the steps in the Removing Foreign Objects  
section.  
Adjusting the Suction Power  
Adjust the suction power using the suction power  
adjustment button on the handle.  
b Filter Cleaning Cycle Alarm Indicator  
• This indicator lights up when the appliance is  
used for a certain period of time. Clean the  
exhaust filter, pre-filter and cyclonic mesh  
filter if necessary.  
c Wi-Fi Indicator  
• This indicator blinks when the appliance is  
connecting to the LG ThinQ application or  
home Wi-Fi network, and the indicator lights  
up when the connection is complete.  
a Power Button  
• Press the Power button to turn the appliance  
on or off.  
• Press the Power button to activate Normal  
mode.  
d Battery Level Indicator  
• The remaining battery level is displayed in 3  
stages according to the remaining battery  
power.  
b Suction Power Up (+) Button / Turbo Mode  
• Press the + button to increase the suction  
power. (Normal~Power~Turbo)  
• The battery level indicator blinks when the  
battery needs to be charged.  
• Press and hold the + button for more than 3  
seconds to activate Turbo mode from Power  
mode.  
• As the product is charging, bars light up on  
the battery level indicator to indicate the level  
of charge.  
c Suction Power Down (-) Button / Wi-Fi Mode  
• When charging is complete, the battery level  
indicator lights up briefly and then turns off  
to save energy.  
• Press the - button to decrease the suction  
power. (Turbo~Power~Normal)  
• Press and hold the - button for 3 seconds to  
activate Wi-Fi and connect the appliance in  
the LG ThinQ application.  
16 OPERATION  
Charging the Battery  
Before Charging the Battery  
• Make sure that the adapter is connected to both  
the charging station and the power outlet.  
• Fully charging a single battery usually takes  
about 4 hours. It will take twice as long to charge  
both the main and auxiliary batteries.  
• The battery will not be charged if the indoor  
temperature is below 41 °F (5°C). Only charge  
the battery when indoor temperatures are  
between 41 °F (5°C) and 100 °F (38 °C).  
WARNING  
• The battery will eventually need to be replaced.  
Due to the battery characteristics, runtime is  
shortened after using the appliance repeatedly  
for an extended period.  
• Make sure to securely fit the product body onto  
the charging station. If the appliance falls off the  
charging station, it could cause injuries, property  
damage or product damage.  
• The last bar on the battery indicator begins to  
blink when the battery needs to be recharged.  
Use the appliance with a fully charged battery.  
• If the main battery is charging on the charging  
station, the auxiliary battery will only start  
charging once the main battery is fully charged.  
Charging the Auxiliary Battery  
After the vacuum cleaner has finished charging,  
the auxiliary battery will start charging.  
• To maintain battery life on dual-battery models,  
swap the positions of the two batteries  
periodically, between the main body and the  
auxiliary charging station.  
One or two batteries are provided. The number of  
batteries varies depending on the model  
purchased.  
1
Lift the front of the control panel located at  
the top of the charging station.  
Charging the Product Body  
Storing the appliance on the charging station  
automatically recharges the battery.  
1
2
Press the Power button to turn the appliance  
off.  
Put the product body onto the charging  
station by aligning it to the hook a of the  
charging station.  
• Make the extension pipe its shortest length  
and insert it into the appliance.  
2
To insert, align the battery with the outline of  
the battery charger.  
• The appliance cannot be loaded onto the  
charging station if either the combination  
tool or the crevice tool is inserted. Use the  
charging station only after removing the  
combination tool or the crevice tool, if  
either happens to be fitted.  
• If you don't hear a beep, reload the  
appliance on the charging station, making  
sure the nozzle is horizontal.  
• When charging is complete, the battery  
level indicator (@) lights up briefly and then  
turns off to save energy.  
3
Press the battery down into the compartment.  
 
OPERATION 17  
When the mop nozzle is attached, the suction is  
turned off and only the mop function operates.  
Press the Power t button to turn the mop on/off.  
• The rotation speed of the mop plates is constant  
and cannot be adjusted.  
CAUTION  
• Do not assemble or disassemble the nozzle while  
the appliance is turned on. Doing so may result  
in injury.  
• Set the water adjustment button to the STOP  
position when not using the appliance for an  
extended period of time. Failure to do so may  
result in product failure.  
NOTE  
• Insert the auxiliary battery completely. If the  
auxiliary battery is inserted correctly, the  
auxiliary battery icon (*) flashes.  
• Do not let the appliance stand on the floor while  
the wet mop pads are attached. Doing so may  
result in damage or swelling to wood flooring.  
• The auxiliary battery icon (*) in the status  
display flashes during charging and then lights  
up briefly and turns off to save energy when  
charging is complete.  
• Do not use on PVC or polyurethane mats for  
infants or children. Friction can cause the motor  
to overheat.  
NOTE  
Using the Mop Nozzle  
• If you use the mop nozzle for a long time, the  
motor may overheat. (Recommended maximum  
run time is 80 minutes.) If the motor overheats, a  
safety function is activated and the appliance  
automatically turns off. Set the appliance in a  
cool, well-ventilated place and allow it to cool  
down for about an hour before resuming use.  
Before Use  
• You cannot adjust the rotation speed of the mop  
plates on the mop nozzle.  
• To prevent product damage, the mop plate will  
automatically stop if there are foreign objects  
stuck in the plate or if it is subjected to a strong  
impact. Turn the appliance off immediately and  
remove the foreign objects or obstructions  
before resuming use.  
Filling the Water Tank  
Before mopping, you must fill the water tank and  
attach it to the mop nozzle.  
• If you hear a noise while mopping, the mop pad  
may have dropped off the mop plate. Turn off  
the product immediately and reattach the pad to  
the mop plate before resuming use.  
1
Press the PUSH button a to remove the  
water tank from the mop nozzle.  
• Do not use a soiled mop pad to clean floors.  
• Set the water adjustment button to the STOP  
position before carrying the appliance around  
with the mop nozzle attached.  
• Use only authorized LG Electronics mop pads.  
• Take care not to accidentally hit the Water  
Adjustment button at the rear of the mop  
nozzle while cleaning around chairs or table  
legs. The water supply level could change or be  
turned to off.  
2
Open the water inlet cap b on the side of the  
water tank and fill the tank with water using  
the water tank filler c.  
• Open only one water inlet cap to fill the  
water. Opening both caps may cause the  
water to flush.  
Using the Mop Nozzle  
• Do not fill the tank over the MAX line d.  
This accessory is only available on some models.  
• Do not use detergent or any liquid other  
than water in the water tank.  
 
18 OPERATION  
• The tank can be filled from either end.  
• Attaching and using mop pads while they  
are dry may affect the cleaning  
performance.  
3
4
Close the water inlet cap tightly.  
2
3
Place the mop nozzle upside down on the  
floor.  
• If the water inlet cap is not closed properly,  
water may leak.  
Align and attach the center of the mop pad  
with the center of the mop plates.  
• Press firmly to attach the Velcro on the mop  
pad to the mop plate. Attaching the mop  
pad upside down or improperly may affect  
the cleaning performance.  
Attach the water tank to the mop nozzle  
again.  
• Insert the 2 tabs e at the front of the water  
tank into the slots f on the top of the mop  
nozzle. Lower the back of the water tank  
into place.  
• Press down at the center g to lock the tank  
in place.  
4
Attach the mop nozzle to the appliance.  
Adjusting the Amount of Water  
Press the Water Adjustment button at the rear of  
the mop nozzle to adjust the amount of water  
released onto the mop pad.  
Attaching the Mop Pads  
Use the standard mop pads for general cleaning.  
For stubborn stains, use the heavy duty mop pads.  
WARNING  
• To avoid injury, do not attach the mop pads  
High Mode: Press the High Mode button a all  
the way down to clean ingrained dirt or supply a  
large amount of water.  
while the mop plates are moving.  
• Do not insert your hand between the rotating  
mop plates. Doing so may result in injury.  
Low Mode: Press the Low Mode button b all  
the way down to supply a small amount of water  
for cleaning wood or other flooring that can be  
damaged by too much water.  
1
Wet both sides of the mop pads with water  
and squeeze out any excess water before  
attaching the pads.  
STOP: Press the Low Mode or High Mode  
button halfway to toggle back to the STOP  
position. This stops the supply of water so you  
can go over areas that are already wet.  
• Do not attach pads while they are dripping  
wet.  
• By default, the water adjustment button is set to  
STOP.  
OPERATION 19  
Using the Mop Nozzle  
1
2
3
Attach the water tank and mop pads to the  
mop nozzle.  
Press the Water Adjustment button to adjust  
the amount of water.  
Press the Power t button to start cleaning.  
2
Leave the 2 water inlet caps open and allow  
the water tank to dry in a well-ventilated area  
out of direct sunlight for at least 24 hours.  
Drying the Water Tank and Mop  
Pads  
• Only store the water tank once it is  
completely empty and dry. Moisture or  
residual water in the tank may cause odor.  
Drying the Water Tank  
When cleaning is completed, make sure to empty  
the water tank and dry it before storing the mop  
nozzle.  
CAUTION  
• Turn the water inlet caps to make sure they  
remain open when storing the water tank. If the  
caps are closed and the tank is not completely  
dry, the trapped moisture can cause odors.  
Drying the Mop Pads  
• Do not remove the water inlet caps from the  
water tank. Caps may tear.  
After using the mop pads, hand wash them and  
allow them to dry before storing them.  
• Do not add detergent, vinegar or baking soda to  
the water tank when washing. It is not easily  
removed from the water tank, and may soil  
floors.  
CAUTION  
• Follow these precautions to prevent mop pads  
from becoming deformed.  
• After cleaning, wipe off any remaining water  
from the water supply inlet a on the mop nozzle  
with a soft cloth. The water could drip onto the  
floor and damage it.  
- Do not use bleach or fabric softener when  
washing the mop pads.  
- Do not dry the pads in a clothes dryer.  
- Do not boil the mop pads.  
1
2
3
Separate the mop pads from the mop plates.  
Hand wash the pads with a neutral detergent.  
• Do not pull or stretch the rubber gasket on the  
water supply inlet. Doing so may tear or damage  
it.  
Set the pads in a well-ventilated area out of  
direct sunlight for at least 24 hours or until  
completely dry.  
1
Open the 2 water inlet caps a on the sides of  
the water tank and empty the water tank.  
Shake the water tank to remove any  
remaining water.  
• Storing the mop pads before they are  
completely dry may cause odors.  
20 OPERATION  
CAUTION  
• Do not use the nozzle on the surfaces listed  
below. Do not use it to clean coated or lacquered  
floors especially, as repeated use can wear down  
the coating.  
- Clothing, bedding  
- Leather sofas, cushions  
- Carpet  
Using the Nozzles and Tools  
- Vinyl flooring, tiles, marble  
Before Using the Nozzles and Tools  
Some accessories are only available on some  
models.  
Bedding Nozzle  
This nozzle lets you clean sheets and bedding  
more effectively. It removes dust in bedding using  
strong suction and a punching motion.  
Specialized attachments can help you clean more  
effectively. Tools and nozzles can be attached to  
the product body or the extension pipe.  
• Adjust the suction power if the inlet gets stuck  
on the floor, carpet, or bedding.  
• Lower the suction level when vacuuming  
bedding such as duvet covers to avoid the thin  
fabric getting sucked into the nozzle.  
• Each nozzle is equipped with a motor and may  
make a sound when operating.  
CAUTION  
• Do not use the Hard Floor Nozzle or Universal  
Nozzle on PVC or polyurethane mats for infants  
and children. The mat may stick to the nozzle,  
making it difficult to operate, causing damage to  
the mat or static electricity on the appliance.  
Clean mats using the crevice tool.  
Crevice Tool  
Use this tool to remove dust from corners or  
Universal Nozzle  
Use this nozzle to clean carpets or rugs.  
narrow spaces.  
• Use it for areas with static electricity such as  
mats.  
• If used on hard flooring, this nozzle will be noisy.  
• Use it with the Turbo mode to clean pet hair out  
of furniture, mats, or tight areas like corners.  
Slim Hard Floor Nozzle  
Use this nozzle to clean hard floor surfaces.  
Pet Nozzle  
Use this nozzle for soft surfaces and pet hair  
removal.  
Combination Tool  
Can be used in either crevice mode or brush mode  
for cleaning corners or small gaps where dust and  
dirt gather.  
Crevice Mode  
 
OPERATION 21  
Use the tool in the crevice mode to clean flat  
surfaces such as sofas or mattresses.  
vehicles or in narrow spaces under and behind  
furniture where an angled tool is needed.  
Brush Mode  
Use the tool in the brush mode to clean delicate  
surfaces such as frames or furniture.  
Using the Brush  
To convert the tool from crevice to brush mode,  
press in on the sides of the brush head a and pull  
the brush down.  
- To convert modes, press the adjustment  
button a and push forward.  
• To convert back to the crevice mode, press in on  
the brush release button b and slide the brush  
up.  
Hard Dirt Tool  
Firm bristles remove solidified dirt from hard  
surfaces. Clean up hair or foreign objects that are  
entangled in carpets or rugs.  
Adjusting the Length  
To adjust the length of the tool, press and hold the  
release button c on the side of the tool. Pull or  
push on the brush head d to extend or retract the  
extension tube.  
Mattress Tool  
Use this tool to clean up dust and foreign objects  
from mattresses, delicate fabrics, and upholstery.  
Multi-angle Tool  
This tool has a soft brush that can be adjusted to a  
variety of angles, making it especially useful for  
cleaning vehicle consoles or the tops of furniture.  
Flexible Crevice Tool  
This tool is flexible and its length can be adjusted,  
making it especially useful for cleaning inside  
Flexible Hose Extension  
Connect this flexible, extendable hose between the  
product body and the tools to clean hard to reach  
areas.  
22 OPERATION  
• The flexible hose extension cannot be used with  
the Nozzle.  
Using the Kompressor Lever  
Use the Kompressor lever to compress hair and  
fibers inside the dust bin after vacuuming and  
before emptying the dust bin.  
• The vacuum must be turned off before using the  
Kompressor lever.  
• Compressing the dust clears it off the interior  
walls of the dust bin and allows you to vacuum  
for longer periods before emptying the dust bin.  
It also makes cleaning the dust bin easier and  
less messy.  
• The dust bin must be at least half full for the  
compression plate to be effective.  
• Press the Kompressor lever down several times  
to compress the dust and clean off the interior  
walls of the dust bin.  
SMART FUNCTIONS 23  
SMART FUNCTIONS  
Before Using LG ThinQ Application  
Using LG ThinQ Application  
The LG ThinQ application allows you to  
communicate with the appliance using a  
smartphone.  
1
2
3
Use a smartphone to check the strength of  
the wireless router (Wi-Fi network) near the  
appliance.  
• If the appliance is too far from the router,  
the signal becomes weak. It may take a long  
time to register or fail to install the  
application.  
LG ThinQ Application Features  
Cleaning History  
- Shows the cleaning history, such as monthly  
cleaning time, cleaning frequency, and  
cleaning mode, etc.  
Turn off the Mobile data or Cellular Data on  
your smartphone.  
NOTE  
• Assembled suction tool is displayed on the  
screen during cleaning.  
• A notification is displayed on the screen if the  
pre-filter and the exhaust filter need cleaning.  
Filter Cleaning Cycle Alarm  
Connect your smartphone to the wireless  
router.  
- After using the appliance for a centain period  
of time, a notification is displayed on the  
screen of your smartphone. Clean the exhaust  
filter or pre-filter, if necessary.  
Cleaning Mode  
- The cleaning mode you are using is displayed  
on the screen of your smartphone.  
NOTE  
Filter Cleaning Guide  
- Guide to cleaning the filters.  
Smart Diagnosis™  
• To verify the Wi-Fi connection, check that the f  
icon on the control panel is lit.  
• The appliance supports 2.4 GHz Wi-Fi networks  
only. To check your network frequency, contact  
your Internet service provider or refer to your  
wireless router manual.  
- This function provides useful information for  
diagnosing and solving issues with the  
appliance based on the pattern of use.  
LG ThinQ is not responsible for any network  
connection problems or any faults, malfunctions,  
or errors caused by network connection.  
NOTE  
• If you change your wireless router, Internet  
service provider, or password, delete the  
connected appliance from the LG ThinQ  
application and connect it again.  
• The surrounding wireless environment can  
make the wireless network service run slowly.  
• If the appliance is having trouble connecting to  
the Wi-Fi network, it may be too far from the  
router. Purchase a Wi-Fi repeater (range  
• This information is current at the time of  
publication. The application is subject to change  
for product improvement purposes without  
notice to users.  
extender) to improve the Wi-Fi signal strength.  
• The network connection may not work properly  
depending on the Internet service provider.  
• The Wi-Fi may not connect or the connection  
may be interrupted because of the home  
network environment.  
   
24 SMART FUNCTIONS  
NOTE  
NOTE  
• If the appliance cannot be connected due to  
problems with the wireless signal transmission,  
unplug the appliance and wait about a minute  
before trying again.  
• The usage history will be reset if you delete a  
connected appliance in LG ThinQ.  
• If the Wi-Fi signal is weak, the appliance may be  
temporarily disconnected to the application.  
When the Wi-Fi signal moves to the normal  
position, the appliance is connected to the  
application again.  
• If the firewall on your wireless router is enabled,  
disable the firewall or add an exception to it.  
• The wireless network name (SSID) should be a  
combination of English letters and numbers. (Do  
not use special characters.)  
• Smartphone user interface (UI) may vary  
depending on the mobile operating system (OS)  
and the manufacturer.  
Turning Wi-Fi On/Off on the  
Appliance  
• If the security protocol of the router is set to  
WEP, network setup may fail. Change the  
security protocol (WPA2 is recommended), and  
connect the product again.  
Disconnecting from Wi-Fi  
To save energy, turn off the Wi-Fi function by  
pressing the Wi-Fi button for 3 seconds while the  
appliance is charging on the charging station.  
Reconnecting to Wi-Fi  
Follow the steps below on the appliance.  
Installing the LG ThinQ Application  
Search for the LG ThinQ application from the  
Google Play Store or Apple App Store on a  
smartphone. Follow instructions to download and  
install the application.  
1
2
Press and hold the Wi-Fi button for 3 seconds  
until the f icon blinks in the display.  
Press the Wi-Fi button for 3 seconds again.  
• After the icon turns off, wait for a while and  
turn it on again.  
Connecting the Appliance to LG  
ThinQ  
• The time before the icon turns on may vary  
depending on the network environment.  
Wi-Fi Indicator f Status  
Indicator  
Description  
Status  
Wireless LAN Module Specifications  
Frequency  
Range  
2412 - 2462 MHz  
Blinking  
ON  
The appliance is connecting.  
The appliance has finished  
connecting.  
The appliance is connected to Wi-Fi.  
Output Power < 30 dBm  
(Max)  
OFF  
The appliance has been  
disconnected.  
FCC Notice  
This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection  
against harmful interference in a residential  
installation. This equipment generates, uses, and  
can radiate radio frequency energy and, if not  
installed and used in accordance with the  
instructions, may cause harmful interference to  
radio communications. However, there is no  
guarantee that interference will not occur in a  
particular installation. If this equipment does  
Connecting the Appliance Initially  
Select your appliance on menu by pressing the  
Add a Product (+) button. Follow instructions in  
the LG ThinQ to connect your appliance.  
Connecting Additional Users  
Remove the appliance from the charging station.  
Follow the instructions under Connecting the  
Appliance Initially.  
SMART FUNCTIONS 25  
cause harmful interference to radio or television  
reception, which can be determined by turning the  
equipment off and on, the user is encouraged to  
try to correct the interference by one or more of  
the following measures:  
Open Source Software Notice  
Information  
To obtain the source code under GPL, LGPL, MPL,  
and other open source licenses, that is contained  
in this product, please visit http://  
opensource.lge.com. In addition to the source  
code, all referred license terms, warranty  
disclaimers and copyright notices are available for  
download.  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment  
and the receiver.  
• Connect the equipment into an outlet on a  
circuit different from that to which the receiver is  
connected.  
LG Electronics will also provide open source code  
to you on CD-ROM for a charge covering the cost  
of performing such distribution (such as the cost of  
media, shipping, and handling) upon email  
request to [email protected]. This offer is valid  
for a period of three years after our last shipment  
of this product. This offer is valid to anyone in  
receipt of this information.  
• Consult the dealer or an experienced radio/TV  
technician for help.  
Any changes or modifications in construction of  
this device which are not expressly approved by  
the party responsible for compliance could void  
the user’s authority to operate the equipment.  
Smart Diagnosis™ Function  
FCC RF Radiation Exposure  
Statement  
This equipment complies with FCC radiation  
exposure limit(<4.0 W/kg for extremity (hand)  
exposure condition) set forth for an uncontrolled  
environment.  
Use this feature to help you diagnose and solve  
problems with your appliance.  
NOTE  
• For reasons not attributable to LGE’s negligence,  
the service may not operate due to external  
factors such as, but not limited to, Wi-Fi  
unavailability, Wi-Fi disconnection, local app  
store policy, or app unavailability.  
This transmitter must not be co-located or  
operating in conjunction with any other antenna  
or transmitter.  
• The feature may be subject to change without  
prior notice and may have a different form  
depending on where you are located.  
Supplier’s Declaration of  
Conformity  
Trade Name  
Responsible Party  
Address  
LG  
Using LG ThinQ to Diagnose Issues  
LG Electronics USA, Inc.  
If you experience a problem with your Wi-Fi  
equipped appliance, it can transmit  
troubleshooting data to a smartphone using the  
LG ThinQ application.  
111 Sylvan Avenue  
North Building  
Englewood Cliffs, NJ 07632  
• Launch the LG ThinQ application and select the  
Smart Diagnosis™ feature in the menu. Follow  
the instructions provided in the LG ThinQ  
application.  
Email  
This device complies with part 15 of the FCC Rules.  
Operation is subject to the following two  
conditions:  
(1) This device may not cause harmful interference  
and  
(2) This device must accept any interference  
received, including interference that may cause  
undesired operation.  
 
26 MAINTENANCE  
MAINTENANCE  
• If the inlets are not completely blocked, the  
foreign objects clogging alarm indicator may not  
light up.  
Cleaning the Appliance  
Before Cleaning the Appliance  
• If the sound of the appliance becomes loud or  
the cleaning performance is poor, check for  
foreign objects.  
To maintain the optimum suction power, the  
cyclonic mesh filter, the exhaust filter and the pre-  
filter should be cleaned regularly and washed  
under running water at least once a month.  
• Turn off the power before cleaning the  
appliance.  
• The frequency of cleaning varies depending on  
the usage environment and usage time. In a  
dusty environment, clean frequently.  
WARNING  
• Never wash the Nozzle, rotating brush or  
product body with water. Water could reach the  
motor and cause electric shock or fire.  
• Do not allow foreign objects to enter the motor.  
Doing so may cause electric shock, fire or  
product damage.  
• Do not insert fingers or sharp objects into the  
motor. Doing so could cause product damage,  
personal injury or electric shock.  
Cleaning the Dust Bin  
Empty and clean the dust bin after every use.  
CAUTION  
• If the dust bin is completely full of dust or the  
filter is clogged, the suction power may be  
reduced.  
• Do not apply force or allow impacts to the  
cyclonic mesh filter. Doing so could deform the  
filter, compromise product performance, or  
cause the product to malfunction.  
CAUTION  
• If the Kompressor lever does not return to the  
top, remove the cyclonic mesh filter from the  
dust bin and clean it. A clogged or dirty filter may  
cause poor product performance.  
• Do not use the appliance without the cyclonic  
mesh filter installed. Doing so could damage the  
appliance.  
1
2
Remove the battery from the product body  
before cleaning the dust bin.  
Removing Foreign Objects  
If the appliance is clogged with foreign objects, the  
suction power changes, the motor cycles  
repeatedly, and the foreign objects clogging alarm  
icon blinks.  
Push down the Kompressor lever a several  
times to collect and compact the dust from  
the outside of the cyclonic mesh filter and the  
interior walls of the dust bin.  
If clogging persists, the appliance will turn off  
automatically to prevent damage. Separate the  
battery from the product body and remove the  
foreign objects before resuming use of the  
appliance.  
• Foreign objects which become lodged in the  
cyclonic mesh filter may be difficult to  
dislodge with the Kompressor lever.  
Remove the cyclonic mesh filter and use the  
provided cleaning brush to clean it.  
• Check the inside of the product body, above the  
Kompressor working plate, the extension pipe,  
inlets, exhaust filter, pre-filter and cyclonic mesh  
filter for foreign objects.  
   
MAINTENANCE 27  
5
Wash the cyclonic mesh filter under running  
water.  
• To avoid odor and the malfunction of the  
motor, allow the cyclonic mesh filter to dry  
completely in a well-ventilated area out of  
direct sunlight for at least 24 hours before  
reassembling.  
3
Press the dust bin cover release button b to  
open the dust bin cover. Shake the dust bin to  
empty it.  
• Be careful as dust or foreign objects may  
spill out when opening the dust bin. Empty  
the dust bin into a wastebasket or where  
dust and foreign objects can be easily  
removed.  
6
Use the combination tool e to clean out dust  
or foreign objects inside the dust bin.  
• The dust bin can be wrapped in a plastic bag  
to contain the dust when emptying the dust  
bin.  
• Do not wash the product body or motor  
with water.  
7
Turn the product body over and lift the  
Kompressor lever f up to clean the inside of  
the working plate with the provided cleaning  
brush.  
WARNING  
• If the Kompressor lever does not slide down  
smoothly, foreign objects may be trapped  
between the dust bin and the cyclonic mesh  
filter. Clean the dust bin and cyclonic mesh filter  
to avoid product damage.  
• Do not push the Kompressor lever down  
hard. The working plate may be damaged.  
• Do not force the Kompressor lever down if  
foreign objects are caught around the working  
plate of the Kompressor system. Doing so may  
cause product damage.  
4
Insert the crevice tool d into the cyclonic  
mesh filter c and turn it counterclockwise to  
remove the filter.  
8
9
Turn the product body over again and shake it  
while pressing down the lever to remove the  
dust.  
Wrap the provided cleaning brush with a wet  
paper towel, tucked into the slots g on the  
handle.  
28 MAINTENANCE  
10 Turn the product body over, lift the  
Kompressor lever h up, and clean the inside  
of the working plate with the towel-wrapped  
brush handle.  
4
5
Lift out the pre-filterd from the product body.  
Cleaning the Filters  
Use the combination tool e to clean any dust  
off the motor.  
Clean the pre-filter and exhaust filter regularly and  
wash them in running water at least once a month  
to maintain the optimum suction power of the  
appliance.  
• Do not wash the motor with water.  
• The frequency of cleaning depends on where  
and how often you use the product. Clean the  
filters more frequently if the appliance is used  
regularly or in areas with a lot of dust.  
• Filters are consumables. Please purchase more  
filters from an authorized service center.  
1
2
Remove the battery from the product body.  
6
Clean the exhuast filter by brushing the dust  
off it regularly and wash it in running water at  
least once a month.  
Rotate the exhaust filter a to the unlocked  
position b to separate it from the product  
body.  
• To avoid odor and the malfunction of the  
motor, allow the exhaust filter to dry  
completely in a well-ventilated area out of  
direct sunlight for at least 24 hours before  
reassembling.  
3
Grip the exhaust filter cover c and the  
exhaust filter a using both hands and rotate  
the exhaust filter cover while pressing the  
PUSH button in order to separate it from the  
exhaust filter.  
MAINTENANCE 29  
7
Clean the pre-filter by brushing the dust off it  
regularly and wash it in running water at least  
once a month.  
• To avoid odor and the malfunction of the  
motor, allow the pre-filter to dry completely  
in a well-ventilated area out of direct  
sunlight for at least 24 hours before  
reassembling.  
CAUTION  
• Do not use the appliance without the exhaust  
filter and pre-filter installed. Doing so could  
result in product damage.  
Cleaning the Nozzle  
8
Align the lock position fo f the exhaust filter  
cover with the letter "H" g of the PUSH  
button on the exhaust filter.  
Clean the nozzle and rotating brush regularly.  
CAUTION  
• Always separate the nozzle from the product  
body or remove the battery before cleaning. If  
the nozzle starts to operate during cleaning, it  
could cause an injury.  
• Keep fingers away from pinch points when  
assembling the nozzle on the appliance or the  
rotating brush on the nozzle.  
• Do not use the rotating brush as a wet mop.  
Doing so may cause product damage.  
9
Push and insert the exhaust filter cover c into  
the exhaust filter a and rotate it to  
reassemble it and prevent it from falling out.  
Cleaning the Universal Nozzle  
Clean the brush and roller heads before each use.  
• If the brush contains foreign objects, the brush  
may not spin or a noise may occur during  
operation.  
1
Press the nozzle release button a to remove  
the nozzle from the extension pipe or product  
body.  
10 Insert the clean, dry pre-filter and rotate the  
exhaust filter to the locked position f to  
reassemble it on the product body.  
2
Turn the nozzle upside down and rotate the  
cover lock slot b counterclockwise.  
 
30 MAINTENANCE  
Cleaning the Slim Hard Floor Nozzle  
1
Press the nozzle release button a to remove  
the nozzle from the extension pipe or product  
body.  
3
4
Pull the brush cover forward and pull the  
brush out.  
2
Turn the nozzle upside down and remove the  
rotating brush while holding down the PUSH  
button on the nozzle.  
Attach the crevice tool to the product body  
and use the vacuum to remove foreign  
objects and dust from the brush and the  
bottom of the nozzle.  
3
4
Attach the crevice tool to the product body  
and use the vacuum to remove foreign  
objects and dust from the brush and the  
bottom of the nozzle.  
5
Use a damp towel or cloth to remove any  
remaining foreign objects and dust from the  
brush and the bottom of the nozzle.  
• Carefully use a tweezers to remove foreign  
objects from the nozzle rollers.  
• Do not rinse or submerge the rotating  
brush or nozzle in water.  
Use a damp towel or cloth to remove any  
remaining foreign objects and dust from the  
brush and the bottom of the nozzle.  
• Wrap the handle of the cleaning brush with  
a wet towel or cloth and use it to clean the  
rotating brush and nozzle.  
• Remove foreign objects from the rollers of  
the nozzle using tweezers.  
• Do not rinse or submerge the rotating  
brush or nozzle in water.  
• Wrap the handle of the cleaning brush with  
a wet towel or cloth and use it to clean the  
rotating brush and nozzle.  
6
Slide the brush back into the nozzle and  
rotate the cover back into place. Turn the  
cover lock clockwise to lock the cover.  
MAINTENANCE 31  
5
Slide the brush back into the nozzle until it  
clicks into place.  
6
Press the brush cover until it clicks to lock the  
brush in place.  
Cleaning the Pet Nozzle  
1
Press the nozzle release button a to remove  
the nozzle from the extension pipe or product  
body.  
Cleaning the Bedding Nozzle  
1
Press the nozzle release button to remove the  
nozzle from the extension pipe or product  
body and turn the nozzle upside down.  
2
Hold down the PUSH button on the nozzle  
while removing the rotating brush.  
2
Attach the crevice tool to the product body  
and use the vacuum to remove foreign  
objects and dust from the bottom of the  
nozzle.  
• Use a damp towel or cloth to remove any  
remaining foreign objects and dust from  
the bottom of the nozzle. After cleaning,  
wipe the nozzle dry.  
• Do not rinse or submerge the nozzle in  
water.  
3
4
Attach the crevice tool to the product body  
and use the vacuum to remove foreign  
objects and dust from the brush and the  
bottom of the nozzle.  
Cleaning the Mop Nozzle  
Use a damp towel or cloth to remove any  
remaining foreign objects and dust from the  
brush and the bottom of the nozzle. Remove  
foreign objects, debris and hair from all  
nozzle rollers using tweezers.  
1
Press the nozzle release button to remove the  
mop nozzle from the extension pipe, and turn  
the nozzle upside down.  
2
Use a damp towel or cloth to remove any  
remaining foreign objects and dust from the  
bottom of the mop nozzle. Remove foreign  
objects, debris and hair from all nozzle rollers  
using tweezers.  
5
Insert the left side of the brush b into the  
groove c inside the nozzle.  
32 TROUBLESHOOTING  
TROUBLESHOOTING  
Before Calling for Service  
Operation  
Problem  
Possible Cause & Solution  
The appliance does  
not operate.  
Battery is fully discharged.  
• Charge the battery.  
Appliance is turned off.  
• Press the Power button to turn on the appliance.  
Suction power is too Dust bin is full of dust.  
weak.  
• Empty the dust bin.  
Filters are clogged.  
• Clean the pre-filter and the exhaust filter.  
Inlet is clogged.  
• Remove any foreign objects from inside the product body or the extension pipe.  
Foreign object is on rotating brush, or in inlet port.  
• Remove any foreign objects (thread, hair) from the rotating brush or the inlet port.  
The product body  
does not appear to  
be charging.  
Power cord is unplugged.  
• Plug the power cord securely into the outlet.  
Foreign object is on the charging terminals.  
• Remove dirt or foreign objects from the charging terminals with a dry cloth.  
Hot air is coming  
from the product  
body.  
Motor is cooling.  
• If the appliance is running normally, the hot air is a result of the motor cooling and is not a  
sign of malfunction.  
A strange odor is  
coming from the  
appliance.  
Appliance was purchased within the last 3 months.  
• The cleaner may emit a smell of rubber for about 3 months after purchase.  
Dust bin is full of dust.  
• The dust in the bin may cause some odor. Empty the bin and clean it.  
Foreign object is on the filter.  
• The filter may emit an odor if it has not been cleaned for some time. Clean the pre-filter  
and exhaust filter regularly.  
Pre-filter was installed while damp or wet.  
• Wash the pre-filter with running water. To avoid odor, allow the pre-filter to dry completely  
in a well-ventilated area out of direct sunlight for at least 24 hours before reassembling.  
Exhaust filter was installed while damp or wet.  
• Wash the exhaust filter with running water. To avoid odor, allow the exhaust filter to dry  
completely in a well-ventilated area out of direct sunlight for at least 24 hours before  
reassembling.  
The appliance makes Vacuum cleaner is running in Turbo mode.  
too much noise.  
• The motor may be louder at the higher suction power settings. This is normal.  
   
TROUBLESHOOTING 33  
Problem  
Possible Cause & Solution  
The appliance turns  
off unexpectedly or  
by itself after the  
motor speed  
Battery is not fully charged.  
• The battery must be fully charged before cleaning. If the problem persists when the  
battery is fully charged and the pipes and attachments are clear from obstructions, contact  
an LG customer information center for service.  
fluctuates  
repeatedly.  
Foreign object is in the product body, extension pipe, inlet port or nozzle.  
• Remove any foreign objects from the product body, extension pipe, inlet port or nozzle.  
Filters are clogged.  
• Clean the pre-filter and the exhaust filter.  
The rotating brush  
does not rotate.  
Brush is improperly installed.  
• Remove the brush, clean it if necessary and attach it again.  
Foreign object is on rotating brush.  
• Remove any foreign objects from the rotating brush.  
Mop Nozzle  
Problem  
Possible Cause & Solution  
The mop plates do  
not rotate.  
Mop pads are improperly installed.  
• Remove the mop pads, clean them if necessary and attach them again.  
Mop nozzle is pressed too hard against the floor.  
• The mop plates stop automatically to protect the product. This is not a failure. Attach the  
mop pads securely to the mop plates and press the Power button to resume use.  
Foreign object is between mop plates and mop pads.  
• Remove foreign objects from the mop plates and press the Power button to resume use.  
There is no water  
coming out of the  
mop nozzle.  
Water tank is empty.  
• Fill the water tank. Remove the battery or detach the nozzle before filling the water tank.  
Water tank is improperly attached to mop nozzle.  
• Properly attach the water tank to the mop nozzle. Remove the battery or detach the nozzle  
before properly securing the water tank to the nozzle.  
Water Adjustment button is set to STOP.  
• Press the High or Low Water Adjustment button all the way down. The water will not  
come out if the button is set to STOP.  
The water outlet was clogged by hard water scale or other foreign substances.  
• Use a sharp pin to remove the blockage.  
There is moisture in  
the water tank.  
Water tank was not allowed to dry completely after use.  
• Empty the water tank, set it out of direct sunlight, and allow it to dry completely after use.  
The mop makes the  
floor dirty or smells  
strange.  
Mop pads were not cleaned properly after use.  
• Clean the mop pads thoroughly after each use. Using soiled mop pads may make the floor  
dirtier.  
34 TROUBLESHOOTING  
Wi-Fi  
Problem  
Possible Cause & Solution  
Your home appliance Battery is fully discharged.  
and smartphone are  
• Charge the battery, then register your appliance on LG ThinQ.  
not connected to the  
Wi-Fi network.  
The password for the Wi-Fi that you are trying to connect to is incorrect.  
• Find the Wi-Fi network connected to your smartphone and remove it, then connect your  
appliance on LG ThinQ.  
Mobile data for your smartphone is turned on.  
• Turn off the Mobile data of your smartphone and connect the appliance using the Wi-Fi  
network.  
The wireless network name (SSID) is set incorrectly.  
• The wireless network name (SSID) should be a combination of English letters and  
numbers. (Do not use special characters.)  
The router frequency is not 2.4 GHz.  
• Only a 2.4 GHz router frequency is supported. Set the wireless router to 2.4 GHz and  
connect the appliance to the wireless router. To check the router frequency, check with  
your Internet service provider or the router manufacturer.  
The appliance is too far from the router.  
• If the appliance is too far from the router, the signal may be weak and the connection may  
not be configured correctly. Move the location of the router so that it is closer to the  
appliance.  
LIMITED WARRANTY 35  
LIMITED WARRANTY  
USA  
TERMS AND CONDITIONS  
ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT  
REQUIRES YOU AND LG ELECTRONICS (“LG”) TO RESOLVE DISPUTES BY BINDING ARBITRATION  
INSTEAD OF IN COURT, UNLESS YOU CHOOSE TO OPT OUT. IN ARBITRATION, CLASS ACTIONS AND  
JURY TRIALS ARE NOT PERMITTED. PLEASE SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING  
DISPUTES” BELOW.  
Should your LG Vacuum Cleaner (“Product”) fail due to a defect in materials or workmanship under normal  
and proper use, during the warranty period set forth below, LG will, at its option, repair or replace the  
Product. This limited warranty is valid only to the original retail purchaser of the Product (“You”) and  
applies only when purchased lawfully and used within the United States including U.S. Territories.  
WARRANTY PERIOD  
Vacuum Cleaner  
Smart Inverter Motor (Suction Motor)  
One (1) year from the date of original retail purchase  
Ten (10) years from the date of original retail  
purchase  
Parts and Labor (internal/functional parts only)  
Parts only (You will be charged for labor)  
• Replacement Products and parts are warranted for the remaining portion of the original warranty period  
or ninety (90) days, whichever is greater.  
• Replacement Products and parts may be new, reconditioned, refurbished, or otherwise factory  
remanufactured.  
• Replaced Product or part(s) will be the property of LG.  
• Proof of original retail purchase specifying the Product model and date of purchase is required to obtain  
warranty service under this limited warranty.  
• Warranty start date will be ninety (90) days from manufacture date absent valid proof of purchase.  
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THE PRODUCT IS LIMITED IN  
DURATION TO THE DURATION OF THE ABOVE LIMITED WARRANTY. UNDER NO CIRCUMSTANCES  
SHALL LG OR ITS U.S. DISTRIBUTORS/DEALERS BE LIABLE FOR ANY INDIRECT, INCIDENTAL,  
CONSEQUENTIAL, SPECIAL, OR PUNITIVE DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST  
GOODWILL, LOST REVENUES OR PROFITS, WORK STOPPAGE, IMPAIRMENT OF OTHER GOODS, COST OF  
REMOVAL AND REINSTALLATION OF THE PRODUCT, LOSS OF USE, OR ANY OTHER DAMAGES WHETHER  
BASED IN CONTRACT, TORT, OR OTHERWISE. LG’S TOTAL LIABILITY, IF ANY, SHALL NOT EXCEED THE  
PURCHASE PRICE PAID BY YOU FOR THE PRODUCT.  
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE  
EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU  
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.  
THIS LIMITED WARRANTY DOES NOT COVER:  
• Service trips to deliver, pick up, install, or clean, or to correct wiring or unauthorized repairs.  
• Service trips to educate how to assemble, operate, or maintain the Product.  
• Damage or failure of the Product to perform during power failures and interrupted or inadequate  
electrical service.  
• Damage or failure of the Product resulting from operating the Product in a corrosive atmosphere or  
contrary to the Product owner’s manual.  
   
36 LIMITED WARRANTY  
• Damage or failure of the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, acts  
of nature, or any other causes beyond the control of LG.  
• Damage or failure of the Product caused by unauthorized modification or alteration, or if the Product is  
used for other than the intended purpose.  
• Damage or failure of the Product caused by incorrect electrical current or voltage.  
• Damage or failure of the Product caused by transportation, storage, and/or handling, including  
scratches, dents, chips, and/or other damage to the finish of the Product, unless such damage is  
reported within one (1) week of delivery.  
• Damage or missing items to any display, open box, or discounted Product.  
• Refurbished Product or any Product sold “As Is”, “Where Is”, “With all Faults”, or similar disclaimer.  
• Products with original serial numbers that have been removed, altered, or cannot be readily determined.  
• Increases in utility costs and additional utility expenses.  
• Any noises associated with normal operation.  
• Products used for other than normal and proper household use (e.g., commercial or industrial use,  
offices, and recreational facilities or vehicles) or contrary to the Product owner’s manual.  
• Costs associated with removal and reinstallation of the Product for repairs.  
• Replacement of batteries, filters, or any consumable parts.  
• The removal and reinstallation of the Product if it is installed in an inaccessible location or is not installed  
in accordance with the Product owner’s manual.  
• Damage or failure of the Product resulting from misuse, abuse, improper installation, repair, or  
maintenance. Improper repair includes the use of parts not authorized by LG. Improper installation or  
maintenance includes installation or maintenance contrary to the Product owner’s manual.  
• Damage or failure of the Product caused by the use of parts, components, accessories, consumable  
cleaning products, detergents, chemicals, or any other products or services that are not authorized by  
LG.  
The cost of repair or replacement under these excluded circumstances shall be borne by You.  
TO OBTAIN WARRANTY SERVICE AND ADDITIONAL INFORMATION  
Call 1-800-243-0000 and select the appropriate option from the menu.  
Or visit our website at http://www.lg.com  
Or by mail: LG Electronics Customer Service P.O. Box 240007 Huntsville, AL 35813 ATTN: CIC  
LIMITED WARRANTY 37  
PROCEDURE FOR RESOLVING DISPUTES:  
ALL DISPUTES BETWEEN YOU AND LG ARISING OUT OF OR RELATING IN ANY WAY TO THIS LIMITED  
WARRANTY OR THE PRODUCT SHALL BE RESOLVED EXCLUSIVELY THROUGH BINDING ARBITRATION, AND  
NOT IN A COURT OF GENERAL JURISDICTION. BINDING ARBITRATION MEANS THAT YOU AND LG ARE EACH  
WAIVING THE RIGHT TO A JURY TRIAL AND TO BRING OR PARTICIPATE IN A CLASS ACTION.  
Definitions. For the purposes of this section, references to “LG” mean LG Electronics U.S.A., Inc., its  
parents, subsidiaries and affiliates, and each of their officers, directors, employees, agents, beneficiaries,  
predecessors in interest, successors, assigns and suppliers; references to “dispute” or “claim” shall include  
any dispute, claim or controversy of any kind whatsoever (whether based in contract, tort, statute,  
regulation, ordinance, fraud, misrepresentation or any other legal or equitable theory) arising out of or  
relating in any way to the sale, condition or performance of the product or this Limited Warranty.  
Notice of Dispute. In the event you intend to commence an arbitration proceeding, you must first notify  
LG in writing at least 30 days in advance of initiating the arbitration by sending a letter to LG at LG  
Electronics, USA, Inc. Attn: Legal Department- Arbitration 111 Sylvan Avenue, Englewood Cliffs, NJ 07632.  
You and LG agree to engage in good faith discussions in an attempt to amicably resolve your claim. The  
notice must provide your name, address, and telephone number; identify the product that is the subject of  
the claim; and describe the nature of the claim and the relief being sought. If you and LG are unable to  
resolve the dispute within 30 days, either party may proceed to file a claim for arbitration.  
Agreement to Binding Arbitration and Class Action Waiver. Upon failure to resolve the dispute during  
the 30 day period after sending written notice to LG, you and LG agree to resolve any claims between us  
only by binding arbitration on an individual basis, unless you opt out as provided below. Any dispute  
between you and LG shall not be combined or consolidated with a dispute involving any other person’s or  
entity’s product or claim. More specifically, without limitation of the foregoing, any dispute between you  
and LG shall not under any circumstances proceed as part of a class or representative action. Instead of  
arbitration, either party may bring an individual action in small claims court, but that small claims court  
action may not be brought on a class or representative basis.  
Arbitration Rules and Procedures. To begin arbitration of a claim, either you or LG must make a written  
demand for arbitration. The arbitration will be administered by the American Arbitration Association  
(“AAA”) and will be conducted before a single arbitrator under the AAA’s Consumer Arbitration Rules that  
are in effect at the time the arbitration is initiated (referred to as the “AAA Rules”) and under the  
copy of your written demand for arbitration, as well as a copy of this provision, to the AAA in the manner  
described in the AAA Rules. You must also send a copy of your written demand to LG at LG Electronics,  
USA, Inc. Attn: Legal Department- Arbitration 111 Sylvan Avenue Englewood Cliffs, NJ 07632. If there is a  
conflict between the AAA Rules and the rules set forth in this section, the rules set forth in this section will  
govern. This arbitration provision is governed by the Federal Arbitration Act. Judgment may be entered on  
the arbitrator’s award in any court of competent jurisdiction. All issues are for the arbitrator to decide,  
except that issues relating to the scope and enforceability of the arbitration provision and to the  
arbitrability of the dispute are for the court to decide. The arbitrator is bound by the terms of this  
provision.  
Governing Law. The law of the state of your residence shall govern this Limited Warranty and any  
disputes between us except to the extent that such law is preempted by or inconsistent with applicable  
federal law.  
Fees/Costs. You do not need to pay any fee to begin an arbitration. Upon receipt of your written demand  
for arbitration, LG will promptly pay all arbitration filing fees to the AAA unless you seek more than $25,000  
in damages, in which case the payment of these fees will be governed by the AAA Rules. Except as  
otherwise provided for herein, LG will pay all AAA filing, administration and arbitrator fees for any  
arbitration initiated in accordance with the AAA Rules and this arbitration provision. If you prevail in the  
arbitration, LG will pay your attorneys’ fees and expenses as long as they are reasonable, by considering  
factors including, but not limited to, the purchase amount and claim amount. Notwithstanding the  
foregoing, if applicable law allows for an award of reasonable attorneys’ fees and expenses, an arbitrator  
can award them to the same extent that a court would. If the arbitrator finds either the substance of your  
claim or the relief sought in the demand is frivolous or brought for an improper purpose (as measured by  
the standards set forth in Federal Rule of Civil Procedure 11(b)), then the payment of all arbitration fees will  
be governed by the AAA Rules. In such a situation, you agree to reimburse LG for all monies previously  
disbursed by it that are otherwise your obligation to pay under the AAA Rules. Except as otherwise  
38 LIMITED WARRANTY  
provided for, LG waives any rights it may have to seek attorneys’ fees and expenses from you if LG prevails  
in the arbitration.  
Hearings and Location. If your claim is for $25,000 or less, you may choose to have the arbitration  
conducted solely on the basis of (1) documents submitted to the arbitrator, (2) through a telephonic  
hearing, or (3) by an in-person hearing as established by the AAA Rules. If your claim exceeds $25,000, the  
right to a hearing will be determined by the AAA Rules. Any in-person arbitration hearings will be held at a  
location within the federal judicial district in which you reside unless we both agree to another location or  
we agree to a telephonic arbitration.  
Opt Out. You may opt out of this dispute resolution procedure. If you opt out, neither you nor LG can  
require the other to participate in an arbitration proceeding. To opt out, you must send notice to LG no  
later than 30 calendar days from the date of the first consumer purchaser’s purchase of the product by  
either: (i) sending an e-mail to [email protected], with the subject line: “Arbitration Opt Out” or (ii) calling 1-  
800-980-2973. You must include in the opt out e-mail or provide by telephone: (a) your name and address;  
(b) the date on which the product was purchased; (c) the product model name or model number; and (d)  
the serial number (the serial number can be found (i) on the product; or (ii) online by accessing https://  
Number”).  
You may only opt out of the dispute resolution procedure in the manner described above (that is, by e-mail  
or telephone); no other form of notice will be effective to opt out of this dispute resolution procedure.  
Opting out of this dispute resolution procedure will not affect the coverage of the Limited Warranty in any  
way, and you will continue to enjoy the full benefits of the Limited Warranty. If you keep this product and  
do not opt out, then you accept all terms and conditions of the arbitration provision described above.  
Memo 39  
LG Customer Information Center  
For inquiries or comments,  
visit www.lg.com or call:  
U.S.A.  
1-800-243-0000  
1-888-542-2623  
CANADA  
Register your product Online!  
OWNER'S MANUAL  
AUTO EMPTY  
CHARGING STATION  
Read this owner's manual thoroughly before operating the  
appliance and keep it handy for reference at all times.  
ENGLISH  
VDS-ST1****  
MFL71780907  
Rev.04_090821  
Copyright © 2021 LG Electronics Inc. All Rights Reserved.  
IMPORTANT SAFETY INSTRUCTIONS  
3
IMPORTANT SAFETY INSTRUCTIONS  
READ ALL INSTRUCTIONS BEFORE USE  
Safety Messages  
Your safety and the safety of others are very important.  
We have provided many important safety messages in this manual and on your appliance. Always read and  
follow all safety messages.  
This is the safety alert symbol.  
This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages  
will follow the safety alert symbol and either the word WARNING or CAUTION.  
These words mean:  
WARNING  
You may be killed or seriously injured if you do not follow instructions.  
CAUTION  
You may be injured or cause damage to the product if you do not follow instructions.  
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,  
and tell you what may happen if the instructions are not followed.  
WARNING STATEMENTS  
WARNING  
• To reduce the risk of explosion, fire, death, electric shock, injury or scalding to persons when using this  
product, follow basic precautions, including the following:  
Technical Safety  
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or  
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or  
instruction concerning use of the appliance by a person responsible for their safety.  
• Do not allow the appliance to be used as a toy. Close attention is necessary when used by or near  
children.  
• Do not allow children to play with or hang on the appliance.  
• Do not use the appliance with a damaged power cord or plug. The cord must be replaced. If the  
appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water,  
return it to an LG Electronics service center.  
• Do not pull or carry by the cord, use the cord as a handle, close a door on the cord, or pull the cord  
around sharp edges or corners. Do not run the appliance over the cord. Keep the cord away from heated  
surfaces.  
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.  
• Place the cords from other appliances out of the area to be cleaned.  
• Have servicing performed by a qualified repair person using only identical replacement parts. This will  
ensure that the safety of the product is maintained.  
4
IMPORTANT SAFETY INSTRUCTIONS  
Battery  
• Never use the battery and the charging station from other appliances with this appliance. Use only the  
battery and the charging station provided by LG Electronics.  
• Use appliances only with specifically designated battery packs. Use of any other battery packs may  
create a risk of injury and fire.  
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of  
battery pack may create a risk of fire when used with another battery pack.  
• Never use the battery and the charging station from this appliance with other appliances.  
• Unplug the power cord from the outlet and remove the battery if the appliance will not be used for an  
extended period of time.  
• Do not use modified or damaged batteries.  
• When disposing of the battery or the appliance, remove the battery from the appliance and safely  
dispose of it.  
• Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may  
exhibit unpredictable behavior resulting in fire, explosion or risk of injury.  
• Do not disassemble, remove or short-circuit the battery.  
• Have the battery replaced when it is no longer able to hold a charge.  
• Refer to the Charging the Battery section instructions for the method of replacing the battery.  
• When disposing of this appliance, follow regulations for disposal of rechargeable lithium-ion batteries.  
• Follow all local ordinances and regulations when handling or disposing of the battery.  
• Disconnect the battery pack before cleaning or servicing.  
• Prevent unintentional starting. Ensure the switch is in the off position before connecting to the battery  
pack, picking up or carrying the appliance. Carrying the appliance with your finger on the switch or  
energizing an appliance that has the switch on invites accidents.  
• When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys,  
nails, screws or other small metal objects, that can make a connection from one terminal to another.  
Shorting the battery terminals together may cause burns or a fire.  
• Under abusive conditions, liquid may be ejected from the battery. If this happens, avoid contact. If  
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.  
Liquid ejected from the battery may cause irritation or burns.  
• Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as indicated  
in the instructions for use and care.  
Installation  
• To avoid an electrical shock or fire, do not install, charge or store the appliance where it may be exposed  
to water, rainfall or high humidity.  
• Install, charge and store the appliance in a well-ventilated place.  
• Avoid operating the appliance in areas where there is a risk of leakage of flammable gas, industrial oil or  
metallic dust.  
• Do not store or install the appliance, power cord or plug near heating devices or open flames.  
• Install the charging station on a firm, level surface.  
• Install the device so that it does not tip over.  
• To prevent tipping, self-standing mode installations should be anchored to the wall using the provided  
anchoring kit.  
• Use the anchoring screws only when attaching to concrete or similar solid surfaces.  
• Never drill into a wall without first checking that the area behind it is free from power conduits,  
plumbing, vents, or cables.  
• Do not use or store the appliance at temperatures below 41 °F (5°C) or above 100 °F (38°C).  
IMPORTANT SAFETY INSTRUCTIONS  
5
• Do not store or install the appliance where it is exposed to temperatures below freezing or exposed to  
outdoor weather conditions.  
• When installing or moving the appliance, be careful not to pinch, crush, or damage the power cord or  
plug.  
Operation  
• This appliance is exclusively for use with the LG Electronics CordZero A9 Vacuum Cleaner. Do not use it  
for other appliances or other purposes.  
• Use only as described in this manual. Use only manufacturer’s recommended attachment.  
• This appliance is designed for normal indoor domestic use only. It is not to be used for any non-  
residential, commercial, or industrial application.  
• Do not use or store the appliance in any outdoor location, garage environment or on wet surfaces.  
• This product should only be used with a 120 V~ 60 Hz outlet. Make sure to check the power specifications  
of the place where you intend to use the appliance.  
• This appliance is equipped with a power cord having an equipment-earthing / grounding conductor  
(earthing pin) and a grounding power plug. The power plug must be plugged into an appropriate outlet  
that is installed and earthed / grounded in accordance with all local codes and ordinances.  
• Do not handle the power cord, plug, or appliance controls with wet hands.  
• Wipe any moisture or dirt off the cord or plug with a dry cloth.  
• Unplug the power cord using the plug, not the cord. Pulling on the cord can damage it and result in  
electric shock or fire.  
• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has  
missing or broken parts, including a damaged cord or plug. Take it to an authorized LG Electronics  
service center or dealer for assistance.  
• Do not apply excessive force to the power cord to bend it, or place it under a heavy object as this will  
damage it.  
• Do not use multiple-outlet adapters with this appliance. Make sure to use a power socket with a capacity  
of 10 A.  
• Do not plug the appliance into a damaged or loose outlet.  
• Make sure to unplug the power cord from the outlet when the appliance is not to be used for an  
extended period of time.  
• Do not damage, alter, excessively bend, twist, pull, pinch or heat the power cord.  
• Before using the appliance, remove any wire or string on the floor.  
• Avoid touching the prongs of the power plug with your finger(s) when unplugging the power cord.  
• Do not cover the power cord with a rug or carpeting.  
• Push the power plug firmly into the wall outlet so that it is not loose.  
• If the product has been submerged, contact an LG Electronics service center or dealer for instructions  
before resuming use.  
• If the product makes a strange noise or emits an odor or smoke, discontinue use and contact an LG  
Electronics customer information center.  
• Only qualified technicians or service personnel from LG Electronics may disassemble, repair or modify  
the appliance.  
• Never insert a sharp metal object such as a pin, nail or knife in a hole or gap in the appliance or the  
charging station.  
• Make sure that no water, beverage or detergent gets inside the appliance or the charging station.  
• Do not allow children to use the appliance.  
• Do not let children or pets get close to the appliance when using, charging or storing.  
• Keep clothing and hair, fingers, or other parts of the body away from openings and moving parts.  
6
IMPORTANT SAFETY INSTRUCTIONS  
• Do not use in an enclosed space where vapors are present from paint thinner, mothproofing substances,  
flammable dust or other explosive or toxic materials.  
• Make sure that the filter is installed before use.  
• Do not touch the charging terminals on the appliance or the charging station, or insert an electrified  
object inside the appliance or the station.  
• Do not lean the appliance on walls, chairs or tables.  
• If the earth leakage breaker is tripped when the product is put on the charging station, immediately  
remove the appliance from the charging station. Contact an LG Electronics customer service center.  
• Do not use or store a heating device or flammable substance (ether, benzene, alcohol, chemicals,  
combustible sprays, insecticide, air freshener or cosmetics) in close proximity to the appliance.  
• Do not attempt to clean up a liquid substance (water, beverage), odorous substances (candy, chocolate,  
pet excrement), metal objects (blades, pins), flammable substances, surfactants, or glass shards with this  
appliance.  
• In the event of a gas leak (natural gas, propane gas, etc.) do not operate this or any other appliance.  
Open a window or door to ventilate the area immediately.  
• Do not hold the charging station upside down with the battery in the charging station.  
• Do not expose the appliance, and the battery in particular, to heat, a heating device or direct sunlight.  
• Do not keep the appliance or its battery inside a vehicle which is exposed to direct sunlight.  
• Never allow any water, beverage or detergent to get inside the battery.  
• Do not apply physical impacts to the battery.  
• Do not use the appliance without the dust bag and filters in place.  
• Do not suck up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.  
• Do not use to suck up flammable or combustible liquids, such as gasoline, or use in areas where they  
may be present.  
• Do not use outdoors.  
Maintenance  
• Make sure to unplug the power cord from the outlet when cleaning or maintaining the charging station.  
• Do not spray or use water, inflammable materials such as gasoline or thinners, or surfactants such as  
detergent or bath soap near the appliance.  
Disposal  
• Keep packing materials out of the reach of children. Packaging materials can pose a suffocation risk for  
children.  
• Destroy the carton, plastic bag, and other packing materials after the appliance is unpacked. Children  
might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight  
chambers.  
• Dispose of this appliance according to local, state, and regional laws and regulations.  
• Contact your local city council or the related government authority before disposing of this appliance.  
• In case a rechargeable battery is included in this product, the entire device should be recycled in  
compliance with rechargeable battery recycling standards because of the internal battery. To dispose of  
IMPORTANT SAFETY INSTRUCTIONS  
7
CAUTION STATEMENTS  
CAUTION  
• To reduce the risk of injury to persons, malfunction, or damage to the product or property when using  
the appliance, follow basic safety precautions, including the following:  
Operation  
• Do not open the door of the product using excessive force.  
• Do not carry the product with the vacuum cleaner, nozzles, or accessories inside; it may cause injury or  
product damage.  
• When opening and closing the product door or control panel, be careful not to get your fingers caught.  
• Remove all the protective plastic from the Vacuum Cleaner before use. Otherwise, it may cause  
abnormal noise during the dust emptying operation.  
• Keep the area around the charging station clean. A strong airstream can be emitted from the exhaust on  
the back of the product, causing dust to accumulate on the floor.  
• This appliance has a built-in safety device to prevent damage from overheating. If the appliance  
becomes overheated after extended use, it may automatically turn off. If this occurs, leave the appliance  
in a cool, well-ventilated area for about an hour before turning on the power again.  
• Do not subject the product to shocks or drop it.  
• Do not install wet or damp filters.  
• Do not clean the product with a volatile or organic solvent (thinner or acetone).  
• Always use a soft cloth to clean the appliance.  
• Remain aware of your surroundings while using the appliance to avoid colliding with people or animals.  
• Do not kick or apply force to the appliance.  
• Do not put any object other than the appliance, especially a metallic or magnetic object, on the charging  
station.  
• Keep fingers away from pinch points when assembling the appliance or the charging station.  
• Do not let a child or a pet hang onto the charging station.  
• Follow all applicable state and local codes and regulations when installing the mounting station.  
• Do not use the double-sided tape to anchor the charging station on wallpaper. Use the provided screws  
to anchor the charging station. The weight of the charging station and the appliance could damage the  
paper.  
• Do not remove the battery during operation.  
SAVE THESE INSTRUCTIONS  
8
INSTALLATION  
INSTALLATION  
Product Overview  
The images in this guide may be different from the actual components and accessories, which are subject  
to change by the manufacturer without prior notice for product improvement purposes.  
NOTE  
• For your safety and for extended product life, use only authorized components. The manufacturer is not  
responsible for product malfunction, property damage or bodily injury caused by the use of separately  
purchased unauthorized components, parts, or non-LG products.  
Front View  
Part Name  
Control Panel  
Part Name  
Exhaust Filter (Expendable)  
Base Plate  
a
b
c
d
e
f
g
h
i
j
k
Vacuum Cleaner Mounting Unit  
Cleaning Brush  
Nozzle Hook  
Bedding Nozzle or Pet Nozzle  
Dust Bag (Expendable)  
Crevice Tool  
Combination Tool  
Motor Protection Filter (Expendable)  
† There is also a nozzle hook on the right.  
NOTE  
• Use the charging station only with the provided vacuum cleaner. Using a vacuum cleaner other than the  
one designed to be used with the charging station may result in improper sealing of the product and  
failure to empty dust from the vacuum cleaner.  
INSTALLATION  
a Cord (includes slide and loop)  
9
Accessories  
b Mounting bands (2EA)  
c Wall Mounting Screw  
d Wall Mounting Anchor  
e Product Mounting Screw  
† This accessory is only available on some models.  
Included Accessories  
NOTE  
• The dust bag exhaust filter and the motor  
protection filter will eventually need to be  
replaced. Contact an LG Electronics customer  
service center.  
a Dust Bag (Expendable)  
b Base Plate  
• The product is shipped with a dust bag already  
installed.  
c Gaskets (4EA)  
Installation Kit  
Specifications  
Appliance  
Model  
VDS-ST1****  
Dimensions  
(Width X Depth X  
Height)  
10.0 in X 11.7 in X 39.7 in  
255 mm X 297 mm x 1009 mm  
Weight  
Approximately 22.3 lb (10.1 kg)  
Power Consumption  
9 A (Cleaning)  
0.6 A (Charging)  
Input  
120 V~ 60 Hz  
Output  
DC 28.3 V / 1.15 A  
Battery  
The charging station finishes charging one battery before charging the second.  
The auxiliary battery will start charging only when the battery in the vacuum cleaner is fully charged.  
NOTE  
• The number of batteries varies depending on the vacuum cleaner purchased. The auxiliary battery is  
available to buy separately.  
10 INSTALLATION  
Model  
EAC63382204  
DC 25.2 V  
Voltage  
Capacity  
2400 mA  
(2) This device must accept any interference  
received, including interference that may cause  
undesired operation.  
FCC Notice  
This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection  
against harmful interference in a residential  
installation. This equipment generates, uses, and  
can radiate radio frequency energy and, if not  
installed and used in accordance with the  
instructions, may cause harmful interference to  
radio communications. However, there is no  
guarantee that interference will not occur in a  
particular installation. If this equipment does  
cause harmful interference to radio or television  
reception, which can be determined by turning the  
equipment off and on, the user is encouraged to  
try to correct the interference by one or more of  
the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment  
and the receiver.  
• Connect the equipment into an outlet on a  
circuit different from that to which the receiver is  
connected.  
• Consult the dealer or an experienced radio/TV  
technician for help.  
Any changes or modifications in construction of  
this device which are not expressly approved by  
the party responsible for compliance could void  
the user’s authority to operate the equipment.  
Supplier’s Declaration of  
Conformity  
Trade Name  
Responsible Party  
Address  
LG  
LG Electronics USA, Inc.  
111 Sylvan Avenue  
North Building  
Englewood Cliffs, NJ 07632  
Email  
This device complies with part 15 of the FCC Rules.  
Operation is subject to the following two  
conditions:  
(1) This device may not cause harmful interference  
and  
INSTALLATION 11  
Installing the Charging  
Station  
CAUTION  
• Do not allow children or pets to hang onto the  
charging station. They could be injured or cause  
damage to the appliance.  
• Take care not to drop the product parts while  
unpacking them to avoid appliance damage or  
personal injury.  
2
Place the base plate on a flat, hard surface  
with the long side facing forward. Place the  
product onto the base plate.  
• Install the base plate with at least 2" (5cm)  
of clearance in the rear. If you plan to store  
the mop nozzle on the station, allow more  
than 2" (5 cm).  
NOTE  
• The cost of a service call to install or reinstall the  
charging station is not covered under the  
warranty.  
• Keep an 8" (20cm) radius in the front clear  
of obstacles in order to open the doors of  
the station.  
Installation  
Follow the steps below to install the charging  
station on a hard and level floor.  
CAUTION  
• Do not install on carpeted floors or rugs. The  
product may fall, causing injury or damage.  
5 cm  
20 cm  
3
Place the station on the base plate and press  
down firmly on all sides to secure it on the  
base.  
• When properly assembled, the base plate  
and station should sit flat on the floor with  
no wobbling or bulges in the base plate.  
• If the base plate and the product are not  
properly assembled, the product may fall over,  
causing product damage or injury.  
1
Before installing the product, attach the  
gaskets a to the four grooves on the rear of  
the base plate b.  
• Peel off the paper from the gasket, remove  
foreign substances from the groove, and  
then attach the sticky side of the gasket to  
the base plate.  
• Attaching the gaskets on the base plate can  
prevent the base plate from slipping or  
scratching the floor when installing the  
product.  
4
Using the anti-tip kit, fix the product firmly to  
the wall.  
12 INSTALLATION  
5
Plug the power plug into the outlet.  
• When the power plug is connected  
correctly, the status display flashes, and the  
product setting is initialized. Once  
initialization is completed, the status display  
turns off.  
2"(5 cm)  
• Use a velcro tie to bind and tidy the excess  
cable.  
Anti-tip Kit Installation  
The anti-tip kit is designed to secure the product to  
the wall in order to prevent it from tipping over  
and causing personal injury or damage to itself or  
the floor.  
2
3
Attach one of the mounting bands to the loop  
at one end of the cord.  
WARNING  
• Carefully read and follow the guidelines in order  
to prevent property damage or personal injury.  
• Do not lean against the product or place a heavy  
object on top of it.  
If drilling into drywall, use a 4 mm bit to drill a  
hole 1 3/4" (44.5 mm) deep at the marked  
location and insert the wall mounting anchor  
first. Then screw the mounting band into the  
anchor with the wall mounting screw. When  
screwing into a wall stud or concrete, use the  
wall mounting screw without the anchor.  
• Manage and supervise children or pets to  
prevent them from knocking into or climbing on  
the product.  
• If you prefer not to install this kit immediately,  
ensure that you keep it out of the reach of  
children.  
• Do not use this kit for purposes other than the  
installation of the charging station.  
4
Thread the other end of the cord through the  
slide as shown to form a loop. Attach the  
second mounting band to this loop.  
• Wear gloves and protective clothing in order to  
prevent personal injury.  
• When drilling a hole in concrete, take caution  
and wear protective goggles.  
• Before drilling into a wall, make sure that there  
are no vents, gas or water pipes, or electrical  
cables behind the wall.  
1
Before moving the product to its final  
position, mark the location on the wall where  
you will attach the anti-tip cord. If you are not  
drilling into a wall stud, you will need to use  
the wall mounting anchor.  
5
6
Use the product mounting screw to attach the  
mounting band to the back of the product.  
• Install the wall mounting anchor and the  
mounting band directly behind the product.  
Place the product in its final location and use  
the slider to adjust the length of the cord until  
there is about 1 inch of play in the cord.  
INSTALLATION 13  
Storage Inside  
CAUTION  
1
Open the left door of the product and insert  
the bedding nozzle or the pet nozzle a for  
storage.  
• Do not tighten the wall mounting screw  
excessively. Doing so may cause the wall  
mounting to come loose and the product to fall,  
resulting in personal injury or product damage.  
• For best results, attach the mounting band to a  
wall stud or a solid wall. If the screw pulls out of  
the wall and the product falls, personal injury or  
product damage may result.  
• If the distance between the wall and the product  
is too great, the product may fall.  
Storing the Accessories  
2
Open the right door and insert the  
combination tool b, the crevice tool c and  
the cleaning brush d for storage.  
Storing the Tools  
Use the product to store the inlet and components  
provided with the vacuum cleaner.  
The components may differ depending on the  
vacuum cleaner model.  
Using the Nozzle Hooks  
1
Open the nozzle hook a on both sides of the  
product.  
• To open the nozzle hooks, press on the right  
side. Be careful not to pinch fingers when  
opening.  
NOTE  
• Before moving the product, unplug it and  
remove the vacuum cleaner, nozzles, and  
accessories.  
• To carry the product, open both doors and hold  
the areas shown.  
2
Hang the nozzle on the nozzle hook.  
14 OPERATION  
OPERATION  
• When charging is complete, the battery  
level indicator (@) lights up briefly and then  
turns off to save energy.  
Charging the Battery  
Before Charging the Battery  
• Make sure that the adapter is connected to both  
the charging station and the power outlet.  
• To save energy while charging the product  
body, press the Select Mode button to  
switch to the manual dust emptying mode.  
• Fully charging a single battery usually takes  
about 4 hours. It will take twice as long to charge  
both the main and auxiliary batteries.  
• The battery will not be charged if the indoor  
temperature is below 41 °F (5°C). Only charge  
the battery when indoor temperatures are  
between 41 °F (5°C) and 100 °F (38 °C).  
• The battery will eventually need to be replaced.  
Due to the battery characteristics, runtime is  
shortened after using the appliance repeatedly  
for an extended period.  
• The last bar on the battery indicator begins to  
blink when the battery needs to be recharged.  
Use the appliance with a fully charged battery.  
WARNING  
• If the main battery is charging on the charging  
station, the auxiliary battery will only start  
charging once the main battery is fully charged.  
• Make sure to securely fit the product body onto  
the charging station. If the appliance falls off the  
charging station, it could cause injuries, property  
damage or product damage.  
• To maintain battery life on dual-battery models,  
swap the positions of the two batteries  
periodically, between the main body and the  
auxiliary charging station.  
Charging the Auxiliary Battery  
After the vacuum cleaner has finished charging,  
the auxiliary battery will start charging.  
Charging the Product Body  
Storing the appliance on the charging station  
One or two batteries are provided. The number of  
batteries varies depending on the model  
purchased.  
automatically recharges the battery.  
1
2
Press the Power button to turn the appliance  
off.  
1
Lift the front of the control panel located at  
the top of the charging station.  
Put the product body onto the charging  
station by aligning it to the hook a of the  
charging station.  
• Make the extension pipe its shortest length  
and insert it into the appliance.  
• The appliance cannot be loaded onto the  
charging station if either the combination  
tool or the crevice tool is inserted. Use the  
charging station only after removing the  
combination tool or the crevice tool, if  
either happens to be fitted.  
2
To insert, align the battery with the outline of  
the battery charger.  
• If you don't hear a beep, reload the  
appliance on the charging station, making  
sure the nozzle is horizontal.  
OPERATION 15  
3
Press the battery down into the compartment.  
NOTE  
• Insert the auxiliary battery completely. If the  
auxiliary battery is inserted correctly, the  
auxiliary battery icon (*) flashes.  
• The auxiliary battery icon (*) in the status  
display flashes during charging and then lights  
up briefly and turns off to save energy when  
charging is complete.  
16 OPERATION  
Getting Started  
Control Panel Features  
Control Panel  
6(/(&7  
02'(  
67$57  
6723  
(PSW\ꢀ'XVW  
List  
Descriptions  
Status Display  
The display shows the dust emptying operation status or when to replace the  
dust bag, charging status of the auxiliary battery, and dust emptying mode.  
a
Start  
Press the Start/Stop button once to start the dust emptying operation when  
using the manual dust emptying mode.  
• When you purchase the product, the automatic dust emptying mode is  
set by default.  
• When the Start/Stop button is selected, a melody plays. Mount the  
vacuum cleaner. The dust bin cover opens automatically, and dust  
emptying operation begins.  
Stop  
Press the Start/Stop button once to cancel or pause the dust emptying  
operation.  
• Dust emptying operates in 3 stages, and its function is different for  
each stage (preparation ~ dust emptying ~ finishing).  
- Pressing the Start/Stop button in the Preparation Stage (mounting  
the body of the vacuum cleaner): The dust emptying operation is  
canceled and the product returns to the charging status.  
b
- Pressing the Start/Stop button in the Dust Emptying Stage (the dust  
bin cover opens automatically, and the dust emptying operation  
begins): The dust emptying (replace bag) indicator flashes white  
along with emitting a beeping sound, and the dust emptying  
operation is paused.  
Repress the Start/Stop button to start additional dust emptying  
operation.  
- Pressing the Start/Stop button in the Finishing Stage (the dust bin  
cover closes automatically, the body of the vacuum cleaner is  
released): Pressing the Start/Stop button does not work  
Change Dust  
Emptying Mode  
Press Select Mode button to switch between automatic or manual dust  
emptying mode.  
OPERATION 17  
Status Display  
AUTO  
List  
Descriptions  
Dust Emptying  
(Replace Bag)  
Indicator  
• Indicates the dust emptying operation status or when to replace the  
dust bag.  
- White: Product is emptying dust.  
- Flashing red: If the indicator flashes red while emptying dust, replace  
the dust bag at the end of the dust emptying operation.  
a
- Flashing red, beeping: If the dust emptying operation is complete and  
the dust bag is full, the indicator will flash red, beep 10 times and  
then turn off.  
- If the indicator flashes red, replace the dust bag to maintain product  
performance.  
Auxiliary Battery  
Indicator  
• Indicates the charging status of the auxiliary battery.  
- Flashes: When the auxiliary battery is mounted in the charger.  
- Lights up briefly and then turns off: Auxiliary battery charging is  
complete.  
b
- The auxiliary battery will not charge until the battery mounted in the  
vacuum cleaner is fully charged. Check the battery level on the handle  
of the vacuum cleaner to check whether charging is complete.  
Auto Emptying  
Indicator  
• Lights to indicate that the automatic dust emptying mode is on.  
- Automatic dust emptying mode automatically starts to operate every  
time the vacuum cleaner is mounted correctly onto the product.  
c
- If you remove the vacuum cleaner and mount it immediately, dust  
emptying operation may not start automatically, depending on the  
circumstance. If it doesn't start automatically, select the Start/Stop  
button to start.  
NOTE  
• Remove all the protective plastic from the vacuum cleaner before use. Otherwise, it may cause abnormal  
noise during the dust emptying operation.  
1
Insert the vacuum cleaner into the product.  
Emptying the Vacuum's Dust Bin  
Using the Auto Mode  
When the automatic dust emptying mode is set,  
the dust emptying operation starts automatically  
whenever the vacuum cleaner is properly inserted  
into the product.  
• After adjusting the length adjustment pipe  
of the vacuum cleaner to the shortest  
length, attach it to the product.  
• If the vacuum cleaner pipe is connected to a  
combination tool or a crevice tool, the  
vacuum cleaner doesn't fit inside the  
product. Use it without the combination  
tool or the crevice tool.  
When you purchase the product, the automatic  
dust emptying mode is set by default.  
• If the vacuum cleaner fits properly inside  
the product, the alarm will sound. If the  
alarm does not sound, reinsert the vacuum  
18 OPERATION  
cleaner, making sure that the nozzle sits flat  
on the floor.  
the product may break or fall, causing injury or  
product damage.  
• Before starting the dust emptying  
operation, pull the easy dust emptying lever  
on the vacuum cleaner down 2 or 3 times to  
sweep away the dust to make the operation  
easier.  
- Remove the vacuum cleaner after the dust  
emptying (replace bag) icon in the status  
display is turned off completely.  
• Do not put foreign objects such as hands,  
garbage, or toys in the dust suction area of the  
product without a vacuum cleaner mounted.  
• Do not push, pull, or lean on the product; it may  
fall, causing injury or damage.  
• Do not put objects like smartphones on the  
product's control panel. The product may  
malfunction due to vibration, or the object may  
fall to the floor, causing injury or damage.  
• If the power suddenly turns off during the dust  
emptying operation, the vacuum cleaner is  
mounted and cannot be removed. Causes for  
power loss include a power outage, a turned off  
power strip, an unplugged power cord, and a  
tripped circuit breaker.  
2
When the dust emptying operation is  
complete, a melody sounds, the dust  
emptying (replace bag) icon turns off, and the  
vacuum cleaner starts charging.  
• After the power comes back on, remove the  
vacuum cleaner when the settings on the  
vacuum cleaner mounting unit are reset.  
Using the Manual Mode  
NOTE  
• The sound of the high-performance motor may  
be louder than the existing wireless vacuum  
cleaner. It is normal to hear sounds such as the  
vacuum cleaner, dust bin cover opening, product  
operating unit, and suction.  
1
Press Select Mode to change from the Auto  
mode to the Manual mode.  
2
3
Insert the vacuum cleaner into the product.  
• The vacuum cleaner mounting unit of the  
charging station is cleaned with a stronger  
suction force just before the dust emptying  
operation is over. The sound may increase, but  
this is normal and not a fault.  
Press the Start/Stop button. The dust  
emptying (replace bag) icon flashes white,  
and the dust emptying operation begins  
along with a melody. Do not try to remove the  
vacuum once the operation starts.  
• During the dust emptying operation, the product  
and auxiliary battery are not charged for safety  
reasons.  
4
When the dust emptying operation is  
complete, a melody sounds, the dust  
emptying (replace bag) icon turns off, and the  
vacuum cleaner starts charging.  
• Replace the dust bag every month to maintain  
the dust emptying performance. The  
replacement cycle may vary depending on the  
environment, and may be especially short in  
conditions with a lot of dust or pet hair.  
WARNING  
• The dust bin may not be emptied completely  
under certain conditions (very full, contains long  
hairs, etc.). If this happens, press Start/Stop to  
repeat the emptying process.  
• Do not wash the vacuum cleaner body or the  
inlet with water. If water enters the built-in  
motor, it can cause electric shock or fire.  
• Clean the dust bin's inside, the easy dust  
emptying lever and the large dust separator to  
remove remaining dust. For more information,  
see the vacuum cleaner owner's manual.  
CAUTION  
• Do not forcibly remove the vacuum cleaner  
during the dust emptying operation or when it is  
paused. Since the vacuum cleaner is mounted,  
• The UV function in the dust bag enclosure  
automatically starts when the vacuum cleaner is  
inserted into the product. It runs for 2 hours or  
OPERATION 19  
until the door is opened or the vacuum cleaner is  
removed.  
20 MAINTENANCE  
MAINTENANCE  
3
4
Clean the dust around the dust suction area  
using a vacuum cleaner.  
Cleaning the Appliance  
Before Cleaning the Appliance  
• Replace the dust bag when the dust emptying  
(replace bag) icon flashes red.  
• Replace the dust bag every month to maintain  
the dust emptying performance.  
• Clean the motor protection filter and the  
exhaust filter every 3 months or if the dust  
emptying function seems weaker.  
Lift the product and clean the base plate.  
• Disconnect the power plug from the outlet  
before cleaning the product.  
• Before moving the product, unplug it and  
remove the vacuum cleaner, nozzles, and  
accessories.  
• If the product smells, replace the dust bag and  
clean the filter.  
• The frequency of cleaning varies depending on  
the usage environment and usage time. In a  
dusty environment, clean frequently.  
• Fine dust may remain on the dust bin cover due  
to static electricity generated during the dust  
emptying operation; periodically clean the dust  
bin cover.  
5
Reassemble the product and the base plate.  
WARNING  
• Make sure that the product and the base  
plate are properly assembled.  
• Never wash the product body with water. Water  
could reach the motor and cause electric shock  
or fire.  
Changing the Dust Bag  
• Do not allow foreign objects to enter the motor.  
Doing so may cause electric shock, fire or  
product damage.  
1
Open the left and right doors of the  
component storage.  
Cleaning the Product Body  
1
Disconnect the power plug from the outlet.  
2
Wipe the control panel using a soft cloth.  
• Product may malfunction if there is dust on  
the control panel.  
2
Hold the product with one hand and open the  
dust bag door with the other hand.  
MAINTENANCE 21  
6
7
Prepare a new dust bag.  
• To avoid odors, do not reuse the dust bags.  
Place the end of the dust bag on the rail inside  
the product.  
• Make sure that the dust bag is level, with  
both sides sitting properly on the rails.  
• Pull the top of the bag away from the rails if  
needed to smoothly insert the bag.  
• If the bag is not inserted properly, dust will  
escape from the top of the bag.  
3
Press n button a above the PUSH label with  
one hand. The dust bag is released.  
8
Slide the dust bag in along the rails of the  
product until it is completely inserted.  
4
Pull out the dust bag lever b to remove the  
dust bag.  
• As the dust bag is pulled out, the top  
opening is closed.  
9
Grab the dust bag lever b and push it up until  
you hear a "click" sound.  
5
Throw away the dust bag.  
22 MAINTENANCE  
2
Hold the product with one hand and open the  
dust bag door with the other hand.  
NOTE  
• The dust bag door will not close without a dust  
bag. Discard the dust bag and be sure to put a  
new dust bag in place.  
• Replace the dust bag every month to maintain  
the dust emptying performance. The  
replacement cycle may vary depending on the  
environment, and may be especially short in  
conditions with a lot of dust or pet hair.  
• Replace the dust bag if it smells, even if it is not  
full.  
• The motor protection filter will eventually need  
to be replaced. Contact an LG Electronics  
customer service center.  
3
Hold the product with one hand and take out  
the motor protection filter with the other  
hand.  
Cleaning the Filters  
Clean the motor protection filter and the exhaust  
filter every 3 months or sooner if the dust  
emptying function seems weaker.  
• Clean the filters more frequently if the appliance  
is used regularly or in areas with a lot of dust.  
CAUTION  
• Do not use the appliance without the exhaust  
filter and the motor protection filter installed.  
Doing so could result in product damage.  
4
To remove the exhaust filter, hold the bottom  
of the product and pull the handle end of the  
filter.  
1
Open the left and right component storage  
doors.  
MAINTENANCE 23  
5
Remove dust from the motor protection filter  
and exhaust filter once every 3 months and  
wash it using room temperature water.  
• To avoid odor and the malfunction of the  
motor, allow the motor protection filter and  
the exhaust filter to dry completely in a well-  
ventilated area out of direct sunlight for at  
least 24 hours before reassembling.  
6
Push the motor protection filter and exhaust  
filter back into their original positions.  
• Make sure that the filters are in place before  
using the product.  
24 TROUBLESHOOTING  
TROUBLESHOOTING  
Before Calling for Service  
Operation  
Problem  
Possible Cause & Solution  
The power plug is not connected.  
• Connect the power plug to an outlet.  
Dust emptying  
doesn't work.  
The Vacuum Cleaner is not properly inserted into the product.  
• Remove the Vacuum Cleaner and reinsert it. If it is installed properly, a beep will sound.  
Dust emptying operation is stopped.  
• When the Dust Emptying Start/Stop button is pressed, the dust emptying operation starts  
from the beginning.  
It is set to automatic or manual dust emptying mode.  
• When you purchase the product, the automatic dust emptying mode is set by default.  
When it is in automatic dust emptying mode, the dust emptying operation starts  
automatically whenever the vacuum cleaner is properly inserted into the product.  
• When it is in manual dust emptying mode, pressing the Dust Emptying Start/Stop button  
starts the dust emptying operation after inserting the vacuum cleaner into the product,  
Product setting  
The internal motor of the product is not operating properly .  
initialization doesn't  
work even after the  
power plug is  
• Disconnect the power plug from the outlet and contact an LG Electronics Service Center.  
plugged in again.  
The power supply  
has been cut off.  
The power supply has been cut off.  
• Check whether the power plug is connected correctly to the outlet.  
• If using a multi-outlet strip, make sure the strip is turned on.  
• Check if the breaker is tripped or there is a power outage.  
It won't charge.  
It is not plugged in.  
• Plug it into an outlet.  
There is a foreign object on the charging terminals.  
• After unplugging from the outlet, wipe off any foreign matter from the charging terminal  
with a dry cloth.  
The room temperature was 41 °F (5 °C) or less during charging.  
• Charging may not work if the temperature where you are charging is 41 °F (5 °C) or less.  
Before use, fully charge the vacuum cleaner at a temperature above 41 °F (5 °C).  
The vacuum cleaner is not properly inserted into the product.  
• When the vacuum cleaner is properly inserted into the product, a beep sounds. If the beep  
does not sound, reinsert the vacuum cleaner.  
The auxiliary battery is not properly inserted into the product.  
• Push in the auxiliary battery all the way. When the auxiliary battery is properly inserted,  
the auxiliary battery icon flashes.  
TROUBLESHOOTING 25  
Problem  
Possible Cause & Solution  
The product is purchased within 3 months.  
The product has a  
strange smell.  
• The odors from manufacturing the product should be gone within 3 months.  
The Vacuum Cleaner smells.  
• After cleaning with the mop nozzle, the wet dust may emit an odor. After finishing  
cleaning, remove the damp dust from the mop nozzle before storing the vacuum.  
• The pre-filter, exhaust filter, or large dust separator may smell after washing if it isn’t dried  
completely. After washing with water, dry them thoroughly in well-ventilated shade for at  
least 24 hours before using them again.  
The dust bag smells.  
• If you clean foreign matter that smells (such as pet excrement) with the vacuum cleaner,  
the vacuum may smell even if you do not have a full dust bag. Replace the new dust bag  
even if it isn't full.  
• If you have not replaced the dust bag for a long time, it may smell. Replace it with a new  
dust bag even if it isn't full.  
Two icons [dust  
emptying (replace  
bag) and auxiliary  
battery] flash  
The motor that holds the Vacuum Cleaner isn't working properly.  
• Disconnect the power plug from the outlet and contact an LG Electronics Service Center.  
The motor that opens and closes the Vacuum Cleaner dust bin cover isn't working  
properly.  
simultaneously.  
• Disconnect the power plug from the outlet and contact an LG Electronics Service Center.  
Two icons (auxiliary  
battery and auto  
emptying) flash  
simultaneously.  
The motor that presses the Vacuum Cleaner dust bin cover separation button isn't  
working properly.  
• Disconnect the power plug from the outlet and contact an LG Electronics Service Center.  
During the dust  
emptying operation,  
the dust emptying  
notification flashes  
red.  
The dust bag is full.  
• Throw away the used dust bag and replace it with a new dust bag.  
The dust emptying  
notification flashes  
red for about 10  
seconds, and a beep  
sounds.  
The dust bag is full.  
• Throw away the used dust bag and replace it with a new dust bag.  
26 Memo  
Memo 27  
LG Customer Information Center  
For inquiries or comments,  
visit www.lg.com or call:  
U.S.A.  
1-800-243-0000  
1-888-542-2623  
CANADA  
Register your product Online!  

Zipper Mowers Max 309 360 User Manual
Toshiba Barcode Reader B Sv4d Gs User Manual
Toshiba 600t User Manual
Sears Aerocool Pd4801 User Manual
Polycom Ip 430 Sip 20 User Manual
HP ELITEBOOK 2740P User Manual
HP 3245A User Manual
EPSON 3200 User Manual
BLACK DECKER GH700 User Manual
BLACK DECKER BDL100AV User Manual