Powered by
USER MANUAL
Smart True HEPA Air Purifier
Models: LV-PUR131S, LV-RH131S, LV-H131S-RXW
Questions or Concerns?
Please contact us Mon–Fri, 9:00 am–5:00 pm PST/PDT
READ AND SAVE THESE
INSTRUCTIONS
SAFETY INFORMATION
To reduce the risk of fire, electric shock, or other injury, follow all instructions and
safety guidelines.
General Safety
•
•
Only use the air purifier as
described in this manual.
•
•
Always unplug the air purifier
before servicing (such as when
changing filters).
Do not use without removing the
plastic wrap from the filters. The air
purifier will not filter air, and may
overheat, causing a fire hazard.
Do not use the air purifier if it is
damaged or not working correctly,
or if the cord or plug is damaged.
Do not try to repair it yourself.
Contact Customer Support (see
page 19).
•
•
Do not use the air purifier
outdoors.
Keep the air purifier away from
water, and wet or damp areas.
Never place in water or other
liquids.
•
•
WARNING: To reduce the risk of
fire or electric shock, do not use
this air purifier with any solid-state
speed controls (such as a dimmer
switch).
•
•
Keep the air purifier away from heat
sources.
Not for commercial use.
Household use only.
Do not use where combustible
gases, vapors, metallic dust,
aerosol (spray) products, or fumes
from industrial oil are present.
•
•
•
Keep 5 ft / 1.5 m away from where
oxygen is being administered.
Supervise children when they are
near the air purifier.
Do not place anything into any
opening on the air purifier, unless
directed by the manual.
•
•
Do not sit on or place heavy
objects on the air purifier.
Keep the inside of the air purifier
dry. To prevent moisture buildup,
avoid placing in rooms with
major temperature changes or
underneath air conditioners.
3
SAFETY INFORMATION (CONT.)
Power & Cord
•
•
•
Keep air purifier near the outlet it is
plugged into.
Never place the cord near any heat
source.
Do not cover the cord with a rug,
carpet, or other covering. Do not
place the cord under furniture or
appliances.
•
•
Keep the cord out of areas where
people walk often. Place the cord
where it will not be tripped over.
This air purifier has a polarized plug
(one blade is wider than the other). To
reduce the risk of electric shock, this
plug is intended to fit in a polarized
outlet only one way. If the plug does
not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a
qualified electrician. Do not attempt
to defeat this safety feature.
•
This air purifier uses standard US
120V, 60Hz outlets. If using outside
the US, check for compatibility.
Electromagnetic Fields (EMF)
Your Levoit air purifier complies with all
standards regarding electromagnetic
fields (EMF). If handled properly and
according to the instructions in this
user manual, the appliance is safe
to use based on scientific evidence
available today.
4
GETTING TO KNOW YOUR AIR PURIFIER
A. LED Display
F. Filter Indicator Reset Button
G. Housing
J. Fine Preliminary Filter
K. H13 True HEPA Filter
L. Filter Cover
B. Touch-Control Panel
C. Dust Sensor Lens
D. Dust Sensor Cover
E. Button Vent
H. Safety Switch
I. High-Efficiency Activated
Carbon Filter
B
A
K
D
C
E
F
G
H
I
L
J
LED DISPLAY
B
A. On/Off Indicator
B. Wi-Fi® Indicator
C. Check Filter Indicator
D. Timer Display
E. Air Quality Indicator
F. Auto Mode
A
C
G
D
E
F
G. Sleep Mode
H. Fan Speed
H
5
CONTROLS
On/Off Button
Wi-Fi Indicator
Turns on, off, or blinks
•
Turns the air purifier on/off.
•
to indicate configuration
status. See the VeSync in-
app instructions for more
information.
•
Press and hold to configure
the air purifier. See the
VeSync in-app instructions
for more information.
Check Filter Indicator Reset
Button
Display Off Button
•
Turns the display off.
•
Press and hold for 3
seconds to reset the
Check Filter Indicator.
•
Press any button (except
) to turn the display
back on.
•
The Check Filter Indicator
lights up when the filter
should be checked
(see page page 11).
Sleep Mode Button
•
Turns Sleep Mode on/off
(see page 9).
Air Quality Indicator
•
Displays air quality using the automatic
dust sensor inside the air purifier.
•
Press and hold for 3
seconds to reset the
Check Filter Indicator.
•
The air purifier may take up to 1 minute
to detect air quality.
Auto Mode Button
•
Turns Auto Mode on/off
(see page 9).
Air Quality Indicator Chart
Color
Air Quality
Red
Bad
Fan Speed Button
•
Cycles through fan
speeds: Low, Medium,
and High.
Yellow
Green
Blue
Moderate
Good
•
The fan speed cannot be
changed in Auto or Sleep
Mode.
Timer Button
Sets or cancels a timer
(see page 9).
•
Very Good
6
Tabs facing
outward
GETTING STARTED
1. Open the filter cover of the air purifier
and remove both filters from their plastic
packaging. [Figure 1.1]
2. Place the High-Efficiency Activated
Carbon Filter back into the air purifier,
followed by the Fine Preliminary/True
HEPA Combination Filter. Make sure the
pull tabs on both filters are facing out.
[Figure 1.2]
Figure 1.2
3. Replace the filter cover by lining up
the cover’s feet with the slots in the
bottom of the housing. Make sure that
the triangular piece at the bottom of
the cover is touching the safety switch.
[Figure 1.3]
Safety
switch
4. Push the cover closed.
5. Place the air purifier on a hard,
flat surface. Leave 15 in / 38 cm of
clearance on all sides of the air purifier.
[Figure 1.4]
Note: Do not remove the foam piece
attached to the dust sensor cover
unless instructed by Customer Support.
[Figure 1.5]
Figure 1.3
15 in /
38 cm
15 in /
38 cm
Figure 1.4
Figure 1.5
Figure 1.1
7
VESYNC APP SETUP
Note: Due to app updates and
improvements, the VeSync app may
be slightly different than shown in the
manual. In case of any differences,
follow the in-app instructions.
1. To download the VeSync app, scan
the QR code or search “VeSync” in
the Apple App Store® or Google Play™
Store. [Figure 2.1]
Note: For Android™ users, you may
need to select Allow to use VeSync.
Figure 2.1
2. Open the VeSync app. If you already
have an account, tap Log In. To create a
new account, tap Sign Up.
VESYNC APP
FUNCTIONS
Note: You must create your own
VeSync account to use third-party
services and products. These will not
work with a guest account. With a
VeSync account, you can also allow
your family and friends to use your
smart air purifier.
The VeSync app allows you to access
additional smart air purifier functions, including
those listed below. As the app develops, more
features may become available.
Remote Control
•
Change any air purifier settings through
the app.
3. Tap + in the VeSync app and select your
smart air purifier.
4. Follow the in-app instructions to finish
setting up your air purifier.
Schedules
Create and customize schedules for
your air purifier to match your routines.
•
Note: You can change the name
and icon at any time in the smart air
purifier settings.
Timer Function
•
Set a timer between 1–24 hours.
•
Easily view the exact time remaining on
a timer.
Connect to Amazon Alexa or
Google Assistant™
You can use the VeSync app to connect
your smart air purifier to Amazon Alexa or
Google Assistant™. Please follow the in-app
instructions to set up your voice assistant.
Filter Replacement Info
•
Keep tabs on the remaining filter life
by checking the filter life percentage in
the app.
•
Shop for replacement filters.
Note: You must create your own VeSync
account to access voice assistants.
Third-Party Voice Control
•
Compatible with Amazon Alexa and
Google Assistant™ for voice commands.
8
USING YOUR SMART AIR PURIFIER
Note: Using the VeSync app allows you to control your air purifier remotely and access
additional functions and features.
General Operation
Auto Mode
1. Plug in and press
on/off. The fan will start on low speed.
to turn the air purifier
Auto Mode uses the dust sensor inside
the air purifier to adjust the fan speed
automatically based on air quality. For
example, if the air quality is bad, the fan
will automatically be set to high speed.
2. Optionally, press to increase fan
speed. You can also select Auto or Sleep
Mode, or set a timer.
•
•
Press
to turn Auto Mode on/off.
Note:
Pressing
Auto Mode.
or will also exit
•
For best results, or to address a
specific air quality issue such as
smoke, run the air purifier at high
speed for 15–20 minutes before
using a lower speed.
Auto Mode Chart
Air Quality
•
To effectively clean air, keep
windows closed while the air
purifier is operating.
Color
Fan Speed
Red
Bad
High
Yellow
Green
Blue
Moderate
Good
Medium
Low
Sleep Mode
Sleep Mode uses the lowest possible fan
speed to maintain a quiet environment.
•
•
Press
to turn Sleep Mode on/off.
or will also exit Sleep Mode.
Very Good
Sleep Mode
Pressing
Timer
Memory Function
You can set a timer between 1–12 hours.
When the air purifier is plugged in, it will
remember its programmed settings while
turned off and resume those settings when
turned back on.
•
Press
in increments of 1 hour. When you stop
pressing , the display will flash 3 times
repeatedly to choose a time
and the timer will start.
•
•
The air purifier will automatically turn off
once the timer is finished.
Automatic Shutoff
To cancel a timer, press
repeatedly
As a safety feature, the air purifier will
automatically turn off if the filter cover
is removed.
until the display reads “-:--” and flashes
3 times.
9
ABOUT THE FILTERS
This air purifier uses a 3-stage filtration
system to purify air.
Clean Air Delivery Rate
This air purifier has a Clean Air Delivery Rate of
135 cubic feet per minute (CFM), or 230 m³/h.
Clean Air Delivery Rate (CADR) measures the
efficiency of an air purifier by indicating the
volume of clean air that an air purifier produces
per minute. This is based on removal of dust,
pollen, and smoke, which are the 3 most
common indoor air pollutants. The higher the
CADR, the more particles the air purifier will
remove and the larger the area it can clean.
The rating is measured at the air purifier’s
highest speed.
A
B
C
A. Fine Preliminary Filter
•
Captures large particles such as
dust, lint, fibers, hair, and pet fur.
•
Maximizes the life of the True
HEPA Filter by protecting it.
Air Change Per Hour
B. H13 True HEPA Filter
The air change rate is how many times all of the
air in a room can be purified (or “changed”) by
the air purifier in 1 hour. Air changes per hour
are calculated on the recommended room size
assuming 8 ft / 2.4 m ceilings. For smaller rooms,
the air change per hour will increase. This air
purifier has an air change per hour of 3, which
means it can change air 3 times at the max
speed in a single, closed room up to 360 ft² /
33 m² in size. The air purifier is effective for
larger rooms, but air purification will take
•
Removes at least 99.97% of
airborne particles 0.3 micrometers
(µm) in diameter.
•
Traps small particles such as
fine dust, smoke particles, and
allergens such as pollen and
pet dander.
C. High-Efficiency Activated Carbon Filter
•
Physically adsorbs smoke, odors,
and fumes.
longer, with fewer air changes per hour.
•
Filters compounds such as
formaldehyde, benzene, ammonia,
hydrogen sulfide, and volatile
organic compounds (VOCs).
Note: To effectively clean air, keep windows
and doors closed while the air purifier is on.
Humidity
Note: Levoit air purifiers filter airborne
particles 0.3 microns in size. Arovast
Corporation makes no claims that this air
purifier helps reduce the COVID-19 virus.
Moisture may damage the filters. This air
purifier should be used in an area with a
humidity level below 85% RH. If you use the
air purifier in excessively humid areas, the
surface of the filters will become moldy.
Essential Oils
Note: Water or moisture will allow mold
to grow. To solve a mold problem, get rid
of the source of the moisture and clean
up the mold.
Do not add essential oils to the air purifier or
filter. The filters will become damaged by the oil
and will eventually release an unpleasant smell.
Do not use oil diffusers near the air purifier.
10
CARE & MAINTENANCE
3. Clean out any remaining dust or hair
inside the air purifier using a vacuum
hose. Do not use water or liquids to
clean the air purifier.
Cleaning the Air Purifier
•
•
Unplug before cleaning.
Wipe the outside of the air purifier with
a soft, dry cloth. If necessary, wipe
the housing with a damp cloth, then
immediately dry.
4. Unwrap the new filters. Place the High-
Efficiency Activated Carbon Filter inside
the housing. Make sure the pull tabs are
facing out.
•
•
Vacuum the inside of the air purifier.
5. Install the Fine Preliminary/True HEPA
Combination Filter into the housing.
Make sure the pull tabs are facing out.
Do not clean with water or any other
liquid, to avoid risk of electric shock.
6. Replace the filter cover. The air purifier
will not turn on unless the filter cover is
replaced correctly.
•
Do not clean with abrasive chemicals or
flammable cleaning agents.
7. Reset the Check Filter Indicator
(see page 13).
Check Filter Indicator
The Check Filter Indicator will light up as
a reminder to check the filters. Depending
on how often you use the air purifier, the
indicator should turn on at about 6–8 months.
You may not need to change your filters
yet, but you should check them when the
indicator light turns on.
Cleaning the Filters
A. The Fine Preliminary Filter should be
cleaned once a month to increase
efficiency and extend the life of your
filter. Clean the Fine Preliminary Filter
using a brush or vacuum hose to
When your air purifier is set up with the
VeSync app, you can also check the app to
see your remaining filter life. You will also
receive a notification from VeSync when it’s
time to check your filter.
remove hair, dust, and large particles.
Note: Make sure you’re cleaning the
correct side of the Combination Filter.
Only clean the side of the filter covered
with the Fine Preliminary Filter.
The VeSync app uses a scientific algorithm to
determine your filter life based on air quality,
amount of use, and other factors. This will
provide a more accurate estimate than the
Check Filter Indicator. The VeSync filter life
percentage is based on 12 hours of daily use.
B. Do not clean the True HEPA Filter. Fine
dust may be released back into the air
if cleaning is attempted. Only clean the
Fine Preliminary Filter.
Reset the Check Filter Indicator by pressing
the black Filter Indicator Reset Button in the
vent on the side of the air purifier
(see page 13).
C. The High-Efficiency Activated Carbon
Filter does not require cleaning.
Replacing the Filters
1. Unplug the air purifier, then remove the
filter cover (see Getting Started, page 7).
A
B
C
2. Remove the old filters.
11
CARE & MAINTENANCE (CONT.)
When Should I Replace the
Filters?
Cleaning the Dust Sensor Lens
1. Unplug the air purifier.
Check the VeSync app to see your remaining
filter life. If the app shows that the filter life is
less than 5%, the filters should be replaced.
2. Open the dust sensor cover. [Figure 2.1]
3. Use a cotton swab dipped in water to
clean the dust sensor lens. [Figure 2.2]
The filters should be replaced every 6–8
months. You may need to replace your filters
earlier or later depending on how often you
use your air purifier. Using your air purifier in
an environment with relatively high pollution
may mean you will need to change the filters
more often.
4. Wipe the lens dry with a dry cotton
swab.
Note: Do not remove the foam piece
attached to the dust sensor cover
unless instructed by Customer Support.
[Figure 2.3]
You may need to replace your filters if you
notice:
•
•
•
•
Increased noise when the air purifier is on
Decreased airflow
Unusual odors
Visibly clogged filters
Note: To maintain the performance of
your air purifier, only use official Levoit
filters. To buy replacement filters, visit
Levoit’s online store. Go to levoit.com
for more information.
Figure 2.1
Figure 2.3
Figure 2.2
12
CARE & MAINTENANCE (CONT.)
Resetting the Check Filter
Indicator
Storage
If not using the air purifier for an extended
period of time, wrap the filters in plastic
packaging and store in a dry place to avoid
moisture damage.
Reset the Check Filter Indicator after
changing the filters.
1. Plug in the air purifier and turn it on.
2. Locate the button vent on the side of
the air purifier. [Figure 3.1]
3. Use a paperclip, small flathead
screwdriver, or other small object to
press the black Filter Indicator Reset
Button in the vent. [Figure 3.1]
4. The Check Filter Indicator will turn off,
indicating that the reset is complete.
Figure 3.1
13
TROUBLESHOOTING
Problem
Possible Solution
Air purifier will not
turn on or respond to
button controls.
Plug in the air purifier.
Check to see if the power cord is damaged. If it is, stop using the air
purifier and contact Customer Support (see page 19).
Securely close the filter cover so that the safety switch is activated (see
page 7).
Plug the air purifier into a different outlet.
The air purifier may be malfunctioning. Contact Customer Support
(see page 19).
Air purifier makes an
unusual noise when
the fan is on.
Make sure the filters are removed from their packaging and properly in
place (see page 7).
Replace the filters (see page 11).
Air purifier may be damaged, or a foreign object may be inside. Stop
using the air purifier and contact Customer Support (see page 19).
Do not try to repair the air purifier.
Make sure the air purifier is operating on a hard, flat, level surface.
Airflow is significantly
reduced.
Make sure the filters are properly in place with plastic packaging
removed (see page 7).
Press
to increase the fan speed.
Leave 15 in / 38 cm of clearance on all sides of the air purifier.
The pre-filter may be clogged by large particles, such as hair or lint,
blocking airflow. Clean the pre-filter (see page 11).
Replace the filters (see page 11).
Check Filter Indicator
is still on after
replacing the filters.
Reset the Check Filter Indicator (see page 13).
14
TROUBLESHOOTING (CONT.)
Problem
Possible Solution
Press to increase the fan speed.
Poor air purification
quality.
Make sure no objects are blocking the top or sides of the air purifier
(the inlet or outlet).
Make sure the filters are removed from their packaging and properly in
place (see page 7).
Close doors and windows while running the air purifier.
If the room is larger than 360 ft² / 33m², air purification will take longer.
The air purifier may not be as effective in significantly larger rooms.
Clean the dust sensor lens (see page 12).
Replace the filters (see page 11).
Check Filter Indicator
has not turned on
within 8 months.
The Check Filter Indicator is a reminder for you to check the filters and
will light up based on how much the air purifier has been used (see
page 11). If you don’t use your air purifier often, the indicator will
take longer to turn on.
Check Filter Indicator
turned on before 6
months.
The Check Filter Indicator is a reminder for you to check the filters and
will light up based on how much the air purifier has been used (see
page 11). If you run your air purifier frequently, the indicator will turn
on sooner.
Air Quality Indicator
always stays red.
Clean the dust sensor lens (see page 12).
If you’re using an ultrasonic humidifier near the air purifier, the mist may
affect the accuracy of the dust sensor. The sensor will detect the large
mist particles, and the Air Quality Indicator may turn red. Avoid using an
ultrasonic humidifier near the air purifier, or avoid using Auto Mode.
Air Quality Indicator
always stays blue,
even when the air
quality is poor.
Clean the dust sensor lens (see page 12).
The dust sensor detects airborne particles, but it cannot detect gas.
Make sure there isn’t gas polluting the air.
Air purifier randomly
turns off.
Air purifier is malfunctioning. Stop using the air purifier and contact
Customer Support (see page 19).
If your problem is not listed, please contact Customer Support (see page 19).
15
VESYNC APP TROUBLESHOOTING
My smart air purifier isn’t connecting to the VeSync app.
•
•
During the setup process, you must be on a secure 2.4GHz Wi-Fi network. Confirm that the
network is working correctly.
Make sure the Wi-Fi password you entered is correct.
•
•
•
There should be no spaces at the beginning or end of the password.
Test the password by connecting a different electronic device to the router.
If you’re manually typing in the SSID and password, double check that both are entered
correctly.
•
Try moving your air purifier closer to the router. Your phone should be as close as possible
to your air purifier.
•
•
Your router may need to be at a higher location, away from obstructions.
Make sure your air purifier and router are away from appliances (such as microwave ovens,
refrigerators, electronic devices, etc.) to avoid signal interference.
•
•
If you’re using a VPN, make sure it’s turned off while setting up your air purifier.
Disable portal authentication for your Wi-Fi network. If portal authentication is enabled, the
air purifier will not be able to access your Wi-Fi network, and setup will fail.
Note: Portal authentication means that you need to sign in to your Wi-Fi network through a
web page before you can use the Internet.
My air purifier is offline.
•
•
•
Make sure the air purifier is plugged in and has power, then refresh the VeSync menu by
swiping down on the screen.
Make sure your router is connected to the internet and your phone’s network connection is
working.
Delete the offline air purifier from the VeSync app. Swipe left (iOS®) or press and hold
(Android™), then tap Delete. Reconfigure the air purifier with the VeSync app.
Note: Power outages, internet outages, or changing Wi-Fi routers may cause the air purifier
to go offline.
If your problem is not listed, please contact Customer Support (see page 19).
16
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
FEDERAL COMMUNICATION COMMISSION
INTERFERENCE STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
FCC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance. To maintain compliance with FCC RF exposure compliance requirements, please
follow operation instructions as documented in this manual. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. This equipment should
be installed and operated with a minimum distance of 20 cm between the radiator and your
body. The availability of some specific channels and/or operational frequency bands are country
dependent and are firmware programmed at the factory to match the intended destination. The
firmware setting is not accessible by the end user.
17
WARRANTY INFORMATION
This warranty extends only to the original consumer
Product Name Smart True HEPA Air Purifier
purchaser of the product and is not transferable to
any subsequent owner of the product regardless
of whether the product is transferred during the
specified term of the warranty.
Models LV-PUR131S, LV-RH131S,
LV-H131S-RXW
For your own reference, we strongly
recommend that you record your order ID
and date of purchase.
This warranty does not extend to products
purchased from unauthorized sellers. Arovast’s
warranty extends only to products purchased from
authorized sellers that are subject to Arovast’s
quality controls and have agreed to follow its quality
controls.
Order ID
Date of
Purchase
All implied warranties are limited to the period of
this limited warranty.
This warranty gives you specific legal rights
and you may also have other rights which vary
from state to state. Some states do not allow the
exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may
not apply to you.
Terms & Policy
Arovast Corporation (“Arovast”) warrants this
product to the original purchaser to be free from
defects in material and workmanship, under
normal use and conditions, for a period of 1 year
from the date of original purchase.
If you discover that your product is defective within
the specified warranty period, please contact
Customer Support via [email protected].
DO NOT dispose of your product before contacting
us. Once our Customer Support Team has
approved your request, please return the product
with a copy of the invoice and order ID.
Arovast agrees, at our option during the
warranty period, to repair any defect in material
or workmanship or furnish an equal product in
exchange without charge, subject to verification
of the defect or malfunction and proof of the date
of purchase.
There is no other express warranty. This
warranty does not apply:
Extend Your Warranty by 1 Year
Register your product within 14 days of purchase
warranty by an additional year.
•
•
If the product has been modified from its
original condition;
If the product has not been used in accordance
with directions and instructions in the user
manual;
This warranty is made by:
•
•
To damages or defects caused by accident,
abuse, misuse or improper or inadequate
maintenance;
To damages or defects caused by service
or repair of the product performed by an
unauthorized service provider or by anyone
other than Arovast;
Arovast Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806
•
•
To damages or defects occurring during
commercial use, rental use, or any use for
which the product is not intended;
To damages or defects exceeding the cost of
the product.
Arovast will not be liable for indirect, incidental,
or consequential damages in connection with the
use of the product covered by this warranty.
18
CUSTOMER SUPPORT
If you have any questions or concerns about
your new product, please contact our helpful
Customer Support Team.
Arovast Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806
Email: [email protected]
Toll-Free: (888) 726-8520
Support Hours
Mon–Fri, 9:00 am–5:00 pm PST/PDT
*Please have your order invoice and order ID
ready before contacting Customer Support.
ATTRIBUTIONS
Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
Google and Google Play are trademarks of Google LLC.
Apple App Store is a trademark of Apple Inc.
Wi-Fi® is a registered trademark of Wi-Fi Alliance®.
iOS is a registered trademark of Cisco Systems, Inc. and/or its affiliates in the United States and
certain other countries.
The energy efficiency of this ENERGY STAR certified model is measured based on a
ratio between the model’s CADR for Smoke and the electrical energy it consumes,
or CADR/Watt.
19
/LEVOITLIFESTYLE
/LEVOIT
/LEVOIT
/LEVOIT
LEVOIT.COM
A2-02.06_S_21C16
|