NX-1000 series
USER MANUAL
B5A-3233-00/02_E_EN
LCD Model ...................................................................................................66
Non-LCD Model............................................................................................67
SCAN..............................................................................................................68
TEMPORARY CHANNEL LOCKOUT ..........................................................68
PRIORITY SCAN .........................................................................................68
SCAN REVERT............................................................................................69
DTMF (DUAL TONE MULTI FREQUENCY) CALLS.......................................70
MAKING A DTMF CALL...............................................................................70
Manual Dialing............................................................................................70
Keypad Auto PTT .......................................................................................70
Store & Send..............................................................................................70
Stun Code ..................................................................................................70
EMERGENCY CALLS....................................................................................71
SCRAMBLER (ANALOG)/ ENCRYPTION (NXDN/ DMR)..............................72
SECURE (ENCRYPTED) TRANSMISSION.................................................72
SELECTING THE SCRAMBLER CODE ......................................................72
SELECTING THE ENCRYPTION KEY ........................................................73
SIGNALING....................................................................................................74
QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT) [ANALOG].......................74
Operator Selectable Tone (OST) [Analog]..................................................74
RADIO ACCESS NUMBER (RAN) [NXDN]..................................................74
COLOR CODE (CC) [DMR] .........................................................................74
OPTIONAL SIGNALING...............................................................................75
5-tone Signaling [Analog] ...........................................................................75
DTMF Signaling [Analog] ...........................................................................75
MDC-1200 Signaling [Analog]....................................................................75
FleetSync Signaling [Analog] .....................................................................75
NXDN ID Signaling [NXDN]........................................................................75
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION ...........................76
SELCALL (SELECTIVE CALLING)..............................................................76
Transmitting................................................................................................76
Receiving....................................................................................................76
Identification Codes....................................................................................77
3
STATUS MESSAGE .....................................................................................77
Transmitting................................................................................................77
Receiving....................................................................................................77
SHORT MESSAGES....................................................................................78
GPS REPORT..............................................................................................78
5-TONE SIGNALING......................................................................................79
SELCALL (SELECTIVE CALLING)..............................................................79
Transmitting................................................................................................79
Receiving....................................................................................................79
STATUS MESSAGE .....................................................................................80
Transmitting................................................................................................80
Receiving....................................................................................................80
VOICE OPERATED TRANSMISSION (VOX) .................................................81
VOX Type....................................................................................................81
VOX Operation ...........................................................................................81
Semi-VOX Operation..................................................................................82
VOX Gain Level ..........................................................................................82
BACKGROUND OPERATIONS......................................................................83
TIME-OUT TIMER (TOT)..............................................................................83
BATTERY SAVER.........................................................................................83
LOW BATTERY WARNING ..........................................................................83
SIGNAL STRENGTH INDICATOR ...............................................................83
VOICE ANNOUNCEMENT...........................................................................84
BUSY CHANNEL LOCKOUT (BCL).............................................................85
4
MODELS COVERED BY THIS MANUAL
The models listed below are covered by this manual:
NXDN/ Analog Transceiver
NX-1200N (VHF TRANSCEIVER)
NX-1300N (UHF TRANSCEIVER)
DMR/ Analog Transceiver
NX-1200D (VHF TRANSCEIVER)
NX-1300D (UHF TRANSCEIVER)
Analog Transceiver
NX-1200A (VHF TRANSCEIVER)
NX-1300A (UHF TRANSCEIVER)
5
NOTIFICATION OF IP67 WATER-RESISTANT MODEL
(Full Button Model)
Water Resistance and Maintenance
Water-Resistant Model transceiver conforms to the following standards.
IP67: The IP standard is the protection level specified by the international
standard IEC 60529. The first numeral indicates the “dust-resistant level” and the
second numeral indicates the “water-resistant” level.
Note:
◆ Initial water-resistant tests and procedures are performed products upon
being ordered from JVCKENWOOD.
PRECAUTIONS
•
The applicable standards listed above do not assure that the transceiver can
be used in water. The transceiver may be damaged in a situation in which the
maximum depth is over 1 meter or the maximum submersion time exceeds 30
minutes.
•
Observe the following precautions to maintain the transceiver’s water resistant
performance:
a) Do not drop or apply strong physical shocks to the transceiver.
b) Do not disassemble or attempt to modify the transceiver. (If it is
disassembled or modified, its performance is not guaranteed.)
c) Do not soak the transceiver in water that contains a solvent or surfactant,
such as detergent or alcohol.
•
If it is soaked in muddy water or salt water (including sea water), it may
become corroded. Immediately flush with fresh water and then wipe dry with a
soft cloth.
•
•
If water is splashed onto the microphone, the battery, or the antenna terminal,
clean and dry them with a soft cloth before reconnecting to the transceiver.
Use of any option on the transceiver not specified by JVCKENWOOD, may
reduce or void the water resistant and dust resistant performance.
6
PREPARATION
INSTALLING THE ANTENNA
Antenna
Screw the antenna into the connector on the top of the
transceiver by holding the antenna at its base and turning it
clockwise until secure.
INSTALLING THE BELT CLIP
If necessary, attach the belt clip using the two
supplied M3 x 8 mm binding screws.
Belt clip
Note:
◆ If the belt clip is not installed, its mounting
location may get hot during continuous
transmission or when left sitting in a hot
environment.
M3 x 8 mm
screws
◆ Use the Phillips #2 screwdriver.
CAUTION
◆ Do not use glue which is designed to prevent screw loosening when
installing the belt clip, as it may cause damage to the transceiver. Acrylic
ester, which is contained in these glues, may crack the transceiver’s back
panel.
7
INSTALLING/ REMOVING THE BATTERY PACK
The battery pack is not charged at the factory; charge it before use.
1 Align the battery pack with the back of the
transceiver, then press the battery pack and
transceiver firmly together until the release latch on
the base of the transceiver locks.
2 To remove the battery pack, lift the safety catch on
the base of the transceiver, then press the release
latch underneath the safety catch.
3 While pressing the release latch, pull the battery
pack away from the transceiver.
CAUTION
◆ Do not short the battery terminals or dispose of the battery by fire.
◆ Never attempt to remove the casing from the battery pack.
◆ Do not remove the black sheet from the reverse side of the transceiver (refer
to the illustration below). Removal of this sheet decreases the waterproof
efficiency of the transceiver and may cause malfunctions if water seeps into
the transceiver. (Full Button Model)
◆ Use KNB-84L battery pack to maintain IP67 waterproof efficiency. (Full
Button Model)
8
INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS
Note:
◆ For the speaker/ microphone jack, waterproof performance is guaranteed by
securing the supplied cap. Waterproof performance will not be guaranteed by
connecting an optional speaker/ microphone, etc.
◆ Use the Phillips #1 screwdriver.
1 If you are not using an optional speaker/
microphone or headset, install the cap over the
speaker/ microphone jacks.
2 Secure the cap in place using the attached screw.
Screw
Speaker/ microphone
jack cap
INSTALLING THE SPEAKER/ MICROPHONE OR HEADSET
Note:
◆ The transceiver is not fully water resistant when using a speaker/ microphone
or headset.
◆ Use the Phillips #1 screwdriver.
1 Insert the speaker/ microphone plugs into the
speaker/ microphone jacks of the transceiver.
2 Place the locking bracket over the speaker/
microphone plugs so that the locking tabs insert
into the transceiver grooves.
3 Secure the locking bracket in place using the
attached screw.
Screw
Speaker/ microphone
locking bracket
9
ORIENTATION
Buttons and Controls
a
b c
Antenna
Speaker
Microphone
f
Display
g
h
d
e
Battery pack
Keypad
Standard Button Model Basic Button Model
Full Button Model
a Selector
Rotate to change the operating channel or zone.
b Status indicator
Lights during a specified mode, based on dealer programming.
(Red, Purple, Blue, Light Blue, Green, Yellow, White)
c Power switch/ Volume control
Turn clockwise to switch ON the transceiver. To switch OFF the transceiver,
turn counterclockwise until a click sounds. Rotate to adjust the volume level.
d [ S ], [ A ], [ <B ], and [ C> ] buttons
• Used for each setting operation.
• Press to activate its programmable function.
e [ ], [ ], and [ ] buttons
Press to activate its programmable function.
f PTT (Push to Talk) switch
Press and hold, then speak into the microphone to transmit.
g Side 1 button
Press to activate its programmable function.
h Side 2 button
Press to activate its programmable function.
10
Display
Indicator
Description
Displays the signal strength.
The Monitor or Squelch Off function is activated.
Blinks when an incoming call matches your Optional Signaling.
The Talk Around function is activated.
Scan, Priority Scan, or Voting/ Site Roaming is in progress. Blinks
when the scan is paused.
A message is stored in the memory. Blinks when a new message is
received.
Indicates Priority Channel.
The channel is using low transmit power.
The Scrambler/Encryption function is activated. Blinks when
receiving an encrypted carrier.
Displays the battery power.
Left side: The current zone is added to the Multi-Zone scanning
sequence.
Right side: The current channel is added to the scanning sequence.
The VOX function is activated.
11
BASIC OPERATIONS
SWITCHING POWER ON/ OFF
Turn the Power switch/ Volume control clockwise to switch the transceiver power
ON.
•
The Power on text appears if the Power on text has been set.
Turn the Power switch/ Volume control counterclockwise to switch the transceiver
power OFF.
ADJUSTING THE VOLUME
Rotate the Power switch/ Volume control to adjust the volume.
Rotate clockwise to increase the volume and counterclockwise to decrease the
volume.
SELECTING A ZONE AND CHANNEL
1 Select the desired zone using the Selector (programmed as [Zone Up/Down]
or [Zone Select]) or buttons programmed as [Zone Up]/ [Zone Down].
•
Each zone contains a group of channels.
2 Select the desired channel using the Selector (programmed as [Channel
Up/Down] or [Channel Select]) or buttons programmed as [Channel Up]/
[Channel Down].
•
•
Each channel is programmed with settings for transmitting and receiving.
The transceiver may have names programmed for zones and channels.
The zone name and channel name can contain up to 8 characters
respectively. While selecting a zone, the zone name appears for 2 seconds
(if Zone Name Display is set), then channel name appears.
12
TRANSMITTING
1 Select the desired zone and channel.
2 Press the button programmed as [Monitor] or [Squelch Off] to check whether
or not the channel is free.
•
If the channel is busy, wait until it becomes free.
3 Press the PTT switch and speak to the microphone. Release the PTT switch to
receive.
•
•
•
The LED indicator lights red while transmitting and green while receiving a
signal. This indicator can also be disabled by your dealer.
For best sound quality, hold the transceiver approximately 3 ~ 4 cm (1.5
inches) from your mouth.
In Site Roaming, In Voting and Voting with Signaling zones, the transceiver
will search for the strongest signal repeater and transmit using that
repeater’s frequency.
Making Group Calls (NXDN/ DMR)
You can select a group ID from the list to make a call to those parties on a channel.
1 Press the button programmed as [Group], [Group + Short Message] or
[Group + Status] to enter Group Call Mode.
•
Alternatively, press the button programmed as [Menu] to enter Group Call
Mode using the Menu Mode.
•
The group ID list appears on the display.
2 Press the [ <B ] and [ C> ] buttons to select a Group ID/ name from the list
that has been programmed into your transceiver.
3 Press and hold the PTT switch to make the call.
•
The “ ” indicator blinks. The Group name of the target transceiver are
displayed.
•
Speak to the microphone as you would during a normal call.
13
Making Individual Calls (NXDN/ DMR)
You can select a Unit ID/ name from the list to make a call to those parties on a
channel.
1 Press the button programmed as [Individual], [Individual + Short Message]
or [Individual + Status] to enter Individual Call Mode.
•
Alternatively, press the button programmed as [Menu] to enter Individual
Call Mode using the Menu Mode.
•
The ID list appears on the display.
2 Press the [ <B ] and [ C> ] buttons to select a Unit ID/ name from the list that
has been programmed into your transceiver.
3 Press and hold the PTT switch to make the call.
•
The “ ” indicator blinks. The ID name of the target transceiver are
displayed.
•
Speak to the microphone as you would during a normal call.
RECEIVING
1 Select the desired zone and channel. (If the Scan function has been
programmed, you can switch it On or Off as desired.)
2 When you hear the caller’s voice, readjust the volume as necessary.
•
If signaling has been programmed on the selected channel, you will hear a
call only if the signaling matches the signaling set up on your transceiver.
•
In Site Roaming, In Voting and Voting with Signaling zones, the transceiver
will automatically search for the strongest signal and receive on that
frequency.
Note:
◆ A ringing tone will sound when receiving a call if the alert tone has been
enabled in the Alert Tone setting. For details, consult your dealer.
14
Receiving Group Calls (NXDN/ DMR)
When you receive a group call on a channel and the received group ID matches
the ID set up on your transceiver, you can hear the caller’s voice.
Receiving Individual Calls (NXDN/ DMR)
When you receive an individual call on a channel, a ringing tone will sound and
the display will show the caller’s ID.
Note:
◆ When water gets into the microphone opening or the speaker grill, the
voice level of the transmission and reception may become low or distorted.
Lightly shake the transceiver to remove the water from the speaker and/or
microphone before operating the transceiver.
15
ACCESSIBLE FUNCTIONS
FUNCTION MODE
Your transceiver operations vary according to the functions that your dealer has
programmed to the transceiver buttons and Selector. Refer to “FUNCTIONS LIST”
MENU MODE (LCD Model)
Many functions on this transceiver are selected or configured through the Menu
instead of physical controls. Once you become familiar with the Menu system, you
will appreciate the versatility it offers.
Some transceiver buttons may already be programmed with functions listed in the
Menu. Those functions can be accessed directly by pressing the button. All other
functions can still be accessed using the transceiver Menu. Refer to “FUNCTIONS
LIST” for the available Menu items.
•
Menu Mode can register functions by category (Up to 12 categories).
Example:
Category
CALL
Function
Individual, Group, Status, Stack
SCAN
Scan, Scan Delete/Add
AUD/TONE
Squelch Off, Squelch Level
•
The category does not appear in Menu Mode when only one category is
configured. When the transceiver enters Menu Mode, the functions registered
in Menu Mode appear.
Menu Access
1 Press the button programmed as [Menu].
•
The category list is shown.
•
When there is only one category, the function list is shown (proceed to step 4).
2 Press [ <B ] and [ C> ] buttons to select a category item.
16
3 Press the [ S ] button to view the function list for the selected category.
4 Press [ <B ] and [ C> ] to select a function item.
•
Press the [ A ] button to return to the category list.
5 Press the [ S ] button. The selected function functions.
•
Options for a function, such as Microphone type, can be selected by
pressing the [ <B ] and [ C> ] buttons and then can be confirmed by
pressing the [ S ] button.
•
Press the Side 1 button at any time to exit Menu Mode.
17
FUNCTIONS LIST
PF Button : Functions that can be programmed to the transceiver buttons
Menu : Functions that can be accessed using the transceiver Menu
Non-LCD : Non-LCD Model
Analog : Channels set up for Analog
NXDN : Channels set up for NXDN
DMR : Channels set up for DMR
✔ : Available
N/A : Not Available
Menu
Display
PF
Button
Non-
LCD
Function
Menu
Analog NXDN DMR
None
–
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
N/A
N/A
✔
✔
✔
✔
N/A
✔
✔
N/A
✔
Autodial
AUTODIAL
Backlight
–
N/A
✔
✔
Battery Status
Broadcast
BAT STAT
✔
✔
✔
BCST
N/A
✔
N/A
✔
✔
✔
✔
Button Lock
Call 1 ~ 6
–
–
–
–
–
–
N/A
N/A
N/A
N/A
N/A
N/A
✔
✔
✔
✔
✔
✔
Calling Alert
Call Interruption
Call Response
Channel Down
N/A
N/A
✔
N/A
✔
✔
✔
N/A
N/A
✔
✔
✔
✔
✔
✔
✔
Channel Down
(Continuous)
–
N/A
✔
✔
✔
✔
✔
Channel Entry
–
–
–
N/A
N/A
N/A
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Channel Recall
Channel Select *1
N/A
✔
Channel Up/
N/A
✔
N/A
N/A
N/A
N/A
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
Down *2
Channel Up
–
–
–
Channel Up
(Continuous)
✔
✔
✔
✔
CW Message
N/A
N/A
✔
✔
18
Menu
Display
PF
Button
Non-
LCD
Function
Menu
Analog NXDN DMR
Digit 1x Down
Digit 1x Up
–
–
–
–
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
✔
✔
✔
✔
✔
✔
✔
✔
Digit 10x Down
Digit 10x Up
Direct Channel
1 ~ 5
–
N/A
✔
✔
✔
✔
✔
✔
✔
DR 1 SEL
~ DR 5
SEL
Direct Channel 1
~ 5 Select
✔
✔
✔
✔
Display Format
Emergency
DISP FMT
–
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
N/A
✔
External
Microphone
Sense
EX MIC S
N/A
N/A
✔
✔
✔
✔
External Speaker SPEAKER
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Fixed Volume
Function
FIXED V
–
N/A
GRP
MODE
Group
N/A
✔
✔
✔
✔
✔
Group + Short
Message
GRP SDM
N/A
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Group + Status
GRP STAT
High Transmit
Power
HIGH
PWR
✔
Home Channel
–
N/A
✔
✔
Home Channel
Select
HOME
SEL
✔
IND
MODE
Individual
N/A
N/A
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Individual + Short
Message
IND SDM
IND STAT
Individual +
Status
19
Menu
PF
Non-
LCD
Function
Menu
✔
Analog NXDN DMR
Display
Button
Lone Worker
L-WK
LOW PWR
MAINT
✔
✔
✔
✔
✔
✔
✔
✔
Low Transmit
Power
✔
✔
✔
Maintenance
N/A
✔
✔
✔
✔
✔
✔
✔
✔
Manual Site Hunt M SITE H
N/A
N/A
✔
Medium 1
Transmit Power
MED1
PWR
N/A
N/A
✔
✔
✔
✔
Medium 2
Transmit Power
MED2
PWR
N/A
N/A
N/A
N/A
✔
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Menu
–
✔
Microphone
Sense
MIC SENS N/A
Microphone Type MIC TYPE
N/A
N/A
N/A
✔
✔
✔
✔
✔
✔
Monitor
MONITOR
–
✔
✔
✔
Monitor
Momentary
N/A
✔
✔
✔
✔
✔
✔
✔
Operator
Selectable Tone
OST
N/A
N/A
N/A
✔
OST List
OVCM
OST LIST
OVCM
N/A
N/A
N/A
N/A
✔
✔
✔
✔
✔
N/A
✔
✔
Priority-channel
Select
PRIORITY
RD CHK
INHIBIT
N/A
N/A
N/A
N/A
N/A
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
N/A
N/A
N/A
✔
✔
N/A
N/A
N/A
✔
Radio Check
(MDC-1200)
N/A
N/A
N/A
✔
Radio Inhibit
(MDC-1200)
✔
Radio Uninhibit
(MDC-1200)
UNINHIB
✔
RMT
CTRL
Remote Control
N/A
N/A
RX Audio
Equalizer
RX EQ
N/A
✔
✔
20
Menu
PF
Non-
LCD
Function
Menu
✔
Analog NXDN DMR
Display
Button
RX Auto Gain
Control
RX AGC
N/A
N/A
N/A
✔
✔
✔
✔
SAVE
LOG
Save Log Data
✔
✔
✔
✔
Scan
SCAN
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Scan Delete/Add
SCN D/A
Scrambler/
Encryption
SCRENC
✔
✔
✔
✔
✔
✔
✔
✔
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Scrambler/
Encryption Code
SCRENC
C
Send the GPS
Data
SEND
GPS
✔
SDM
MODE
Short Message
N/A
✔
✔
Speaker
Attenuation
–
N/A
Speaker Type
Squelch Level
Squelch Off
SPK TYPE N/A
N/A
N/A
✔
N/A
✔
✔
✔
✔
✔
N/A
✔
✔
N/A
✔
SQL LVL
SQL OFF
✔
✔
✔
Squelch Off
Momentary
–
N/A
✔
✔
✔
✔
✔
Stack
STACK
STATUS
N/A
N/A
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Status
Surveillance
Talk Around
SURVEIL
TALK ARD
Transceiver
Password
TRNS
PWD
N/A
N/A
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
TX Audio
Equalizer
TX EQ
N/A
N/A
N/A
N/A
TX Auto Gain
Control
TX AGC
VOX
VOX LVL
VOX
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
VOX Function
21
Menu
Display
PF
Button
Non-
LCD
Function
Menu
Analog NXDN DMR
Zone Delete/Add ZONE D/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Zone Down
–
–
N/A
Zone Down
N/A
✔
✔
✔
✔
✔
(Continuous)
Zone Select *3
Zone Up/Down *4
Zone Up
–
–
–
N/A
N/A
✔
N/A
N/A
N/A
✔
N/A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Zone Up
(Continuous)
–
N/A
✔
✔
✔
✔
✔
*1: [Channel Select] can be programmed only on the Selector of the Non-LCD
model. Cannot be set with [Channel Up] and/or [Channel Down] together.
*2: [Channel Up/Down] can be programmed only on the Selector of the LCD
model.
*3: [Zone Select] can be programmed only on the Selector of the Non-LCD
model. Cannot be set with [Zone Up] and/or [Zone Down] together.
*4: [Zone Up/Down] can be programmed only on the Selector of the LCD model.
22
FUNCTIONS OVERVIEW
Following is a brief overview of the functions available on the transceiver
accessible using the Menu and/or programmable to the transceiver buttons.
•
For details on functions that are not included in “FUNCTIONS OVERVIEW”
None [Analog/ NXDN/ DMR]
No function has been programmed.
Autodial [Analog]
Allows you to quickly send DTMF codes from the Autodial List.
1 PF Button: Press the programmed button to enter Autodial Mode.
Menu Mode: Select “AUTODIAL” and press the [ S ] button to enter Autodial
Mode.
2 Press the [ <B ] and [ C> ] buttons to select your desired list of Autodial.
3 Press the PTT switch to make the call.
Backlight [Analog/ NXDN/ DMR]
Allows you can turn the LCD display backlight on/off.
PF Button:
Press the programmed button to turn the display backlight On or Off.
•
If Auto backlight is activated by your dealer, the backlight can be set to
activate by button operations or when receiving a call/ message.
23
Battery Status [Analog/ NXDN/ DMR]
Allows you to check the battery power status.
PF Button:
Press the programmed button, the Battery Status function operates.
Menu Mode:
Select “BAT STAT” and press the [ S ] button, the Battery Status function operates.
Battery status is represented by the number of times the LED indicator flashes
red. Four flashes represents full power, three represents medium power, two
represents low power, and one represents very low power. If the LED flashes red
only one time, recharge or replace your battery pack immediately.
Indicator
(LCD-Model)
Battery remaining
LED
Beep tone
Full
Sufficient
Low
Blink 4 times
Blink 3 times
Blink 2 times
Sounds 4 times
Sounds 3 times
Sounds 2 times
Very Low
Blink 1 time
Sounds 1 time
•
•
power is low or less, this button will not operate.
If the Battery Level Tone has been enabled, a beep tone will sound according
to the number of flashes from the LED.
Broadcast [DMR]
Allows you to make a Broadcast Group Call. Broadcast Group Call can be used to
engage in one-way informative group voice calls by initiating a call to a group.
PF Button:
Press the programmed button, to switch to Broadcast Call.
Menu Mode:
Select “BCST” and press the [ S ] button to switch to Broadcast Call.
•
“BCST ON” is displayed for 1 second and Broadcast Group Call will be On.
24
Button Lock [Analog/ NXDN/ DMR]
Locking the transceiver button operation. This function prevents the incorrect
operation of the transceiver by physical contact while carrying the transceiver,
such as around the waist.
PF Button:
Press the programmed button to lock the transceiver buttons.
•
Beep A (1 beep) sounds.
Press the button again to unlock.
•
•
Beep B (2 beeps) sounds.
While Button Lock is on, operate a button that has been locked. “LOCKED” is
displayed for 1 second.
•
•
Even if a button on the transceiver is pressed while the Button Lock is
enabled, a Button-entry Error Tone (1 beep) sounds.
Whether each button operation is targeted for the Button Lock can be
configured by your dealer. The following buttons are targeted for the Button
Lock when each configuration is enabled:
- Selector, Front Buttons, Side Buttons, Volume Control, and PTT Switch.
The following will still function and can be operated as per normal.
•
- Backlight, Battery Status, Button Lock, Call Response, Clear, Emergency,
Function, Monitor, Monitor Momentary, Lone Worker, Squelch Off, and
Squelch Off Momentary.
Call 1 ~ 6 [Analog/ NXDN/ DMR]
Allows you to send assigned signaling from Call 1 to Call 6.
PF Button:
Press the programmed button to send a message or initiate a call.
Calling Alert [Analog]
Allows you to send a calling alert to the other party. Calling alert tones help
identify yourself to party members and inform them that you are calling.
PF Button:
Press the programmed button to send an Alert tone to a receiver.
25
Call Interruption [DMR]
Allows a transceiver other than the transmitting transceiver to terminate voice
communications by sending a Call Interruption request message. If a transceiver
receives a Call Interruption request message on the channel where the
transceiver is performing voice communications, the transceiver terminates the
voice communications.
PF Button:
Press the programmed button to send Call Interruption Request message.
Call Response [NXDN/ DMR]
Allows you to send an acknowledge call, upon receipt of the acknowledgment
request message from an individual call.
PF Button:
Press the programmed button to respond to an Individual Call.
26
Channel Entry [Analog/ NXDN/ DMR]
In Channel Entry Mode, channel can be selected by the same operation as List
selection.
PF Button:
1 Press the programmed button to enter Channel Entry Mode.
2 Press the [ <B ] and [ C> ] buttons to select your desired channel.
3 Press the [ S ] button to confirm the entry.
To enter 2-digit channel number (example: Channel 12):
1 Press the programmed button to enter Channel Entry Mode.
2 Press the [ <B ] and [ C> ] buttons to select “1”
3 Press the [ S ] button.
4 Press the [ <B ] and [ C> ] buttons to select “2”.
•
Press the [ A ] button to delete 1 digit number. Press and hold the [ A ]
button to delete all numbers.
5 Press the [ S ] button to confirm the entry.
27
To enter 3-digit channel number (example: Channel 123):
1 Press the programmed button to enter Channel Entry Mode.
2 Press the [ <B ] and [ C> ] buttons to select “1”
3 Press the [ S ] button.
4 Press the [ <B ] and [ C> ] buttons to select “2”.
5 Press the [ S ] button.
6 Press the [ <B ] and [ C> ] buttons to select “3”.
•
Press the [ A ] button to delete 1 digit number. Press and hold the [ A ]
button to delete all numbers.
7 Press the [ S ] button to confirm the entry.
Channel Recall [Analog/ NXDN/ DMR]
PF Button:
Press the programmed button during Scan to return to the last called zone and
channel and Scan pauses (Scan Stop Tone will sound every 30 seconds).
•
Beep A (1 beep) sounds.
28
Channel Select [Analog/ NXDN/ DMR]
Selector:
Turn the Selector to select the channel number.
Channel Up/Down [Analog/ NXDN/ DMR]
Selector:
Turn the Selector to increase/ decrease the channel number.
Channel Up/ Channel Down [Analog/ NXDN/ DMR]
PF Button:
Press the programmed button to increase/ decrease the channel number.
Channel Up (Continuous)/ Channel Down (Continuous)
[Analog/ NXDN/ DMR]
PF Button:
Hold down the programmed button to continuously increase/ decrease the
channel number.
Clear [Analog/ NXDN/ DMR]
Allows you to cancel the data (Status Message, Short Message, Remote Control
Message, Call Alert, etc.) transmission, reject an incoming call, or disconnect the
call.
PF Button:
Press the programmed button to end a call or cancel a status message
transmission.
•
•
Beep A (1 beep) sounds.
“CANCEL” is displayed for 1 second.
CW Message [NXDN]
Sending CW Message.
PF Button:
Press the programmed button to send the set Morse code.
29
Digit 1x Up/ Digit 1x Down [Analog]
In 5-tone to increment/ decrement the 5-tone selcall code by 1.
PF Button:
Press the programmed button to increase/ decrease the 5-tone selcall code by 1
with each press.
1st digit code from the right of 5-tone
selcall code
Digit 10x Up/ Digit 10x Down [Analog]
In 5-tone to increment/ decrement the 5-tone selcall code by 10.
PF Button:
Press the programmed button to increase/ decrease the 5-tone selcall code by 10
with each press.
2nd digit code from the right of 5-tone
selcall code
Direct Channel 1 ~ 5 [Analog/ NXDN/ DMR]
Allows you to go directly to Direct Channel 1 ~ 5.
PF Button:
Press the programmed button to jump to a frequently used zone and channel.
•
Beep A (1 beep) sounds.
Press this button again to return to the formerly selected channel.
Beep B (2 beeps) sounds.
•
If activated by your dealer, you can set your own Direct Channels by selecting
your desired zone and channel using Direct Channel 1 ~ 5.
30
Direct Channel 1 ~ 5 Select [Analog/ NXDN/ DMR]
Allows you to set the currently selected channel as the Direct Channel 1 ~ 5.
1 Select the channel to be set as Direct Channel.
2 PF Button: Press and hold the programmed button to set the currently
selected channel as Direct Channel 1 ~ 5.
•
Beep C (3 beeps) sounds.
Menu Mode: Select “DR 1 SEL” ~ “DR 5 SEL” and press the [ S ] button to set
the currently selected channel as Direct Channel 1 ~ 5.
Display Format [Analog/ NXDN/ DMR]
Allows you to switch the display between the zone-channel number and the
channel name.
Zone-channel number
Channel name
PF Button:
Press the programmed button to switch the display between the zone-channel
number and the channel name.
Menu Mode:
Select “DISP FMT” and press the [ S ] button to change the Display Format
setting.
31
Emergency [Analog/ NXDN/ DMR]
This is for entering Emergency Mode if the transceiver is in standby mode. If the
transceiver is in Emergency mode, it exits the emergency mode. In Emergency
Mode, the transceiver repeats transmission and reception at regular intervals.
PF Button:
Press and hold the programmed button for the time set in hold delay to enter
Emergency Mode.
•
If transceiver is in Emergency Mode, press and hold this button for the time
set in Hold Delay to exit Emergency Mode.
External Microphone Sense [Analog/ NXDN/ DMR]
Allow you to set the microphone sensitivity of the external microphone.
Menu Mode:
1 Select “EX MIC S” and press the [ S ] button.
2 Press the [ <B ] and [ C> ] buttons to select the microphone sensitivity.
•
You can select from +6 dB (High sensitivity) to -20 dB (Low sensitivity) by 2
steps.
3 Press the [ S ] button to confirm and exit mode.
32
External Speaker [Analog/ NXDN/ DMR]
If external speaker connected to the transceiver, select the output of the speaker
to the external speaker or internal speaker.
PF Button:
Press the programmed button to switch the external speaker or internal speaker.
Menu Mode:
1 Select “SPEAKER” and press the [ S ] button.
2 Press the [ <B ] and [ C> ] buttons to switch the external speaker or internal
speaker.
External speaker
Internal speaker
3 Press the [ S ] button to confirm and exit mode.
Fixed Volume [Analog/ NXDN/ DMR]
Allows you to change the volume level of the tone.
PF Button:
Press the programmed button to change Low, High, or Off (Tone Off).
Menu Mode:
1 Select “FIXED V” and press the [ S ] button.
2 Press the [ <B ] and [ C> ] buttons to select Low, High, or Off (Tone Off).
3 Press the [ S ] button to confirm and exit mode.
33
Function [Analog/ NXDN/ DMR]
Allows you to access the 2nd function programmed to a button. Programmable
buttons can be assigned Main function and 2nd function.
PF Button:
1 Press the programmed button to enter 2nd function input wait state.
•
•
Beep A (1 beep) sounds.
“FNC” is displayed.
2 Press the button which has been programmed a 2nd function to perform the
2nd Function.
Group [Analog/ NXDN/ DMR]
Activates Group Call Mode.
1 PF Button: Press the programmed button to enter Group Call Mode (NXDN/
DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
Menu Mode: Select “GRP MODE” and press the [ S ] button to enter Group
Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
2 Press the [ <B ] and [ C> ] buttons to select a Group ID/ name from the list
that has been programmed to your transceiver.
3 Press and hold the PTT switch to make the call.
NXDN/ DMR:
FleetSync:
5-Tone:
34
Group + Short Message [Analog/ NXDN/ DMR]
Allows you to specify a Group ID to send short messages.
1 PF Button: Press the programmed button to enter Group Call Mode (NXDN/
DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
Menu Mode: Select “GRP SDM” and press the [ S ] button to enter Group Call
Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
2 Press the [ <B ] and [ C> ] buttons to select a Group ID/ name from the list.
3 Press the [ S ] button to enter Short Message Mode.
4 Press the [ <B ] and [ C> ] buttons to select a Short Message from the list
(NXDN/ DMR).
5 Press the PTT switch or Side 2 button to send short messages.
Group + Status [Analog/ NXDN/ DMR]
Allows you to specify a Group ID to send status messages.
1 PF Button: Press the programmed button to enter Group Call Mode (NXDN/
DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
Menu Mode: Select “GRP STAT” and press the [ S ] button to enter Group Call
Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
2 Press the [ <B ] and [ C> ] buttons to select a Group ID/ name from the list.
3 Press the [ S ] button to enter Status Mode.
4 Press the [ <B ] and [ C> ] buttons to select the status messages you want to
transmit.
5 Press the PTT switch or Side 2 button to send status messages.
35
High Transmit Power [Analog/ NXDN/ DMR]
Turns High Transmit Power On or Off. When using a channel programmed with low
or medium power, this allows you to change the output power to high.
PF Button:
Press the programmed button to change the output power to high.
•
Beep A (1 beep) sounds.
Press this button again to change the transmit power to the original setting.
Beep B (2 beeps) sounds.
•
Menu Mode:
Select “HIGH PWR” and press the [ S ] button to change the High Transmit Power
On or Off.
•
•
The “ ” indicator appears while using Low transmit power.
The “ ” indicator disappears while using High or Medium transmit power.
High or Medium Transmit Power
Low Transmit Power
Home Channel [Analog/ NXDN/ DMR]
Allows you to jump to home channel (programmed by your dealer). If activated
by your dealer, you can set your own Home Channel by selecting your desired
channel using Home Channel Select.
PF Button:
Press the programmed button to jump to home channel.
•
•
Beep A (1 beep) sounds.
“HOME” is displayed for 1 second.
Press this button again to return to the formerly selected channel.
Beep B (2 beeps) sounds.
•
36
Home Channel Select [Analog/ NXDN/ DMR]
Allows you to set the currently selected channel to Home Channel.
1 Select the channel to be set as Home Channel.
2 PF Button: Press and hold the programmed button to set the currently
selected channel as the Home Channel.
•
Beep C (3 beeps) sounds.
Menu Mode: Select “HOME SEL” and press the [ S ] button to set the currently
selected channel as the Home Channel.
Individual [Analog/ NXDN/ DMR]
Activates Individual Call Mode.
1 PF Button: Press the programmed button to enter Individual Call Mode
(NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
Menu Mode: Select “IND MODE” and press the [ S ] button to enter Individual
Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
2 Press the [ <B ] and [ C> ] buttons to select a Unit ID/ name from the list that
has been programmed to your transceiver.
3 Press and hold the PTT switch to make the call.
NXDN/ DMR:
FleetSync:
5-Tone:
37
Individual + Short Message [Analog/ NXDN/ DMR]
Allows you to specify a Unit ID to send short messages.
1 PF Button: Press the programmed button to enter Individual Call Mode
(NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
Menu Mode: Select “IND SDM” and press the [ S ] button to enter Individual
Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
2 Press the [ <B ] and [ C> ] buttons to select a Unit ID/ name from the list.
3 Press the [ S ] button to enter Short Message Mode.
4 Press the [ <B ] and [ C> ] buttons to select a Short Message from the list
(NXDN/ DMR).
5 Press the PTT switch or Side 2 button to send short messages.
Individual + Status [Analog/ NXDN/ DMR]
Allows you to specify a Unit ID to send status messages.
1 PF Button: Press the programmed button to enter Individual Call Mode
(NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
Menu Mode: Select “IND STAT” and press the [ S ] button to enter Individual
Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200/ 5-tone).
2 Press the [ <B ] and [ C> ] buttons to select a Unit ID/ name from the list.
3 Press the [ S ] button to enter Status Mode.
4 Press the [ <B ] and [ C> ] buttons to select the status messages you want to
transmit.
5 Press the PTT switch or Side 2 button to send status messages.
38
Lone Worker [Analog/ NXDN/ DMR]
Using Lone Worker function, the transceiver can automatically enter Emergency
Mode and notify the base station of the emergency status when the transceiver
becomes disabled from operating due to an accident.
PF Button:
Press the programmed button to change the Lone Worker On.
•
Beep A (1 beep) sounds.
Press this button again to change the Lone Worker Off.
Beep B (2 beeps) sounds.
•
Menu Mode:
Select “L-WK” and press the [ S ] button to change the Lone Worker On or Off.
•
•
Lone Worker is turn On, “L-WK ON” is displayed for 1 second.
If transceiver is on the Lone Worker mode, Lone Worker is turn Off, “L-WK
OFF” is displayed for 1 second.
On the Lone Worker mode, Lone Worker Interval time(r) will be counting down.
When you press any button to indicate that you are safe and the timer will be
restarted.
The transceiver automatically enters Emergency Mode if you do not operate the
transceiver during the Lone Worker Interval time.
39
Low Transmit Power [Analog/ NXDN/ DMR]
Turns Low Transmit Power On or Off. When using a channel programmed with
medium or high power, this allows you to change the output power to low.
PF Button:
Press the programmed button to change the output power to Low.
•
Beep A (1 beep) sounds.
Press this button again to change the transmit power to the original setting.
Beep B (2 beeps) sounds.
•
Menu Mode:
Select “LOW PWR” and press the [ S ] button to change the Low Transmit Power
On or Off.
•
•
The “ ” indicator appears while using Low transmit power.
The “ ” indicator disappears while using High or Medium transmit power.
High or Medium Transmit Power
Low Transmit Power
40
Maintenance [Analog/ NXDN/ DMR]
Allows you to display the signal strength and Bit Error Rate (BER) on the LCD
when constructing the system or during maintenance.
1 PF Button: Press the programmed button to enter Maintenance Display Mode.
Menu Mode: Select “MAINT” and press the [ S ] button to enter Maintenance
Display Mode.
2 Press the [ <B ] and [ C> ] buttons to select Signal strength (RSSI Level) or
BER.
Signal strength (RSSI Level: dBm)
Bit Error Rate
•
•
BER display is available on NXDN/ DMR channel.
When the signal strength is less than -120 dBm, “
” is displayed.
•
When BER measurement is impossible, “
” is displayed.
3 Press the [ S ] button to confirm and exit mode.
41
Manual Site Hunt [DMR]
Allows you can manually move the Revert Channel to another Channel without
waiting for Site Roaming to resume.
PF Button:
On the Channel of DMR Site Roaming, press the programmed button, the Manual
Site Hunt function operates.
•
Beep A (1 beep) sounds.
Menu Mode:
Select “M SITE H” and press the [ S ] button, the Manual Site Hunt function
operates.
•
Search Mode Tone sounds and send a Wakeup message once to other
Channels registered in the same System set in DMR Site Roaming and go to
search for repeaters that can detect the synchronization signal.
•
"SEARCH" is displayed during Manual Site Hunt operation.
Medium 1 Transmit Power [Analog/ NXDN/ DMR]
Turns Medium 1 (2.5 W) Transmit Power On or Off. When using a channel
programmed with low or high power, this allows you to change the output power to
medium 1.
Menu Mode:
Select “MED1 PWR” and press the [ S ] button to change the Medium 1 Transmit
Power On or Off.
Medium 2 Transmit Power [Analog/ NXDN/ DMR]
Turns Medium 2 (4 W) Transmit Power On or Off. When using a channel
programmed with low or high power, this allows you to change the output power to
medium 2.
Menu Mode:
Select “MED2 PWR” and press the [ S ] button to change the Medium 2 Transmit
Power On or Off.
42
Menu [Analog/ NXDN/ DMR]
PF Button:
Press the programmed button to select and perform functions using the
transceiver Menu.
Microphone Sense [Analog/ NXDN/ DMR]
Allows you to change the internal microphone sensitivity.
Menu Mode:
1 Select “MIC SENS” and press the [ S ] button.
2 Press the [ <B ] and [ C> ] buttons to select the microphone sensitivity.
•
You can select from +6 dB (High sensitivity) to -20 dB (Low sensitivity) by 2
steps.
3 Press the [ S ] button to confirm and exit mode.
43
Microphone Type [NXDN/ DMR]
Allows you to configure the type of the external microphone to be connected to
the transceiver and enables the optimal conditions of the audio quality.
Menu Mode:
1 Select “MIC TYPE” and press the [ S ] button.
2 Press the [ <B ] and [ C> ] buttons to select the microphone type.
•
You can select from None (without adjusting the audio characteristics),
MIC 1 to MIC 11.
3 Press the [ S ] button to confirm and exit mode.
Type
Model
MIC 1 KMC-45*, KMC-45D
MIC 2 KMC-48GPS*
MIC 3 KMC-21
KHS-7, KHS-7A*, KHS-8BL, KHS-8BE, KHS-9BL, KHS-9BE,
MIC 4 KHS-21*, KHS-22, KHS-22A, KHS-25, KHS-26, KHS-27, KHS-27A,
KHS-31, KHS-31C
MIC 5 KHS-23, KHS-35F
MIC 6 KHS-10-BH*, KHS-10-OH*, KHS-10D-BH, KHS-10D-OH
MIC 7 EMC-11, EMC-12
MIC 8 KHS-1*
MIC 9 KHS-29F
MIC 10 KEP-2
MIC 11 KHS-8NC
* : Not support for DMR.
44
Monitor [Analog/ NXDN/ DMR]
Allows you to turn the transceiver signaling off, to listen to all calls that are
received on the channel.
PF Button:
Press the programmed button to change the Monitor On.
•
Beep A (1 beep) sounds.
Press this button again to change the Monitor Off.
Beep B (2 beeps) sounds.
•
Menu Mode:
Select “MONITOR” and press the [ S ] button to change the Monitor On or Off.
•
The “ ” indicator appears while Monitor is On.
Monitor Momentary [Analog/ NXDN/ DMR]
PF Button:
Press and hold the programmed button to momentarily turn the transceiver
signaling off. Releasing this button turns the transceiver signaling back on. While
signaling is off, you can listen to all calls that are received on the channel.
Operator Selectable Tone [Analog]
Switches the preset QT/DQT Decode/Encode pair to an OST (Operator
Selectable Tone) pair.
PF Button:
Press the programmed button to change the OST On or Off.
Menu Mode:
Select “OST” and press the [ S ] button to change the OST On or Off.
45
OST List [Analog]
Allows you to enter OST List mode.
1 PF Button: Press and hold the programmed button to enter OST List Mode.
Menu Mode: Select “OST LIST” and press the [ S ] button to enter OST List
Mode.
2 Press the [ <B ] and [ C> ] buttons to select the OST List.
3 Press the [ S ] button to confirm and exit mode.
OVCM (Open Voice Channel Mode) [DMR]
Allows you to hear various voice calls (Individual Call, Group Call, Broadcast Call)
even if the received ID does not match.
PF Button:
Press the programmed button to change the OVCM On.
•
Beep A (1 beep) sounds.
Press this button again to change the OVCM Off.
Beep B (2 beeps) sounds.
•
Menu Mode:
Select “OVCM” in Menu Mode and press the [ S ] button to change the OVCM On
or Off.
46
Priority-channel Select [Analog/ NXDN/ DMR]
A Priority channel must be programmed in order for Priority Scan to function.
When using a single Priority channel, the transceiver will automatically change to
the Priority channel when a call is received on it, even if a call is being received on
a normal channel.
When using dual Priority channels, Priority channel 1 is given precedence over
Priority channel 2. So, if a call is received on Priority channel 1 while a call is
already on Priority channel 2, the transceiver will automatically change to Priority
channel 1.
1 Select the channel to be set as Priority channel.
2 PF Button: Press the programmed button to set the current channel as the
Priority Zone-Channel.
Menu Mode: Select “PRIORITY” and press the [ S ] button to enter Priority-
channel Select Mode.
3 Press the [ <B ] and [ C> ] buttons to select “NORMAL” (scan off), “PRI 1”
(priority 1), “PRI 2” (priority 2), or “PRI 1 2” (priority 1/2).
4 Press the [ S ] button to confirm and exit mode.
•
The “
channel.
” indicator appears on the display when the channel is Priority
47
Radio Check (MDC-1200) [Analog]
This function is for MDC-1200 Radio Check. Radio Check is a function for
checking whether a transceiver is available for calling, such as whether the
transceiver is on or whether it is within the reach of radio waves.
Menu Mode:
1 Select “RD CHK” and press the [ S ] button to enter Radio Check Mode.
2 Press the [ <B ] and [ C> ] buttons to select the destination ID from the ID List.
3 Press the PTT switch to start Radio check.
4 When ACK (Acknowledgement) is received, “COMPLETE” is displayed for 1
second.
Radio Inhibit (MDC-1200) [Analog]
This function is for MDC-1200 Radio Inhibit. Radio Inhibit is a function for stunning
a transceiver.
Menu Mode:
1 Select “INHIBIT” and press the [ S ] button to enter Radio Inhibit Mode.
2 Press the [ <B ] and [ C> ] buttons to select the destination ID from the ID List.
3 Press the PTT switch to send Radio Inhibit command.
4 When ACK (Acknowledgement) is received, “COMPLETE” is displayed for 1
second.
48
Radio Uninhibit (MDC-1200) [Analog]
This is for MDC-1200 Radio Uninhibit. Radio Uninhibit is a function for reviving a
transceiver which has been stunned.
Menu Mode:
1 Select “UNINHIB” and press the [ S ] button to enter Radio Uninhibit Mode.
2 Press the [ <B ] and [ C> ] buttons to select the destination ID from the ID List.
3 Press the PTT switch to send Radio Uninhibit command.
4 When ACK (Acknowledgement) is received, “COMPLETE” is displayed for 1
second.
49
Remote Control [NXDN/ DMR]
Allows you to remotely control a specified transceiver from the transceiver.
In the NXDN and DMR systems, it allows you to operate the transceiver directly,
send a remote control message and control the target transceiver.
Note:
◆ The Remote Control is a software option.
In Remote Control Mode, the following remote control message can be sent.
Remote Stun: Send a Remote Stun Message to the designated Transceiver and
make the Transceiver unusable.
Remote Revive: Send a Remote Revive Message to the designated Transceiver
and release the Stun state of the Transceiver.
Remote Kill: Send a Remote Kill Message to the designated Transceiver and
make Transceiver inoperable and prevent any operation.
Remote Monitor: Send a Remote send request message to the specified
Transceiver, Individual Call from the Transceiver to the requester, cancel Mic Mute
and send it continuously.
Radio Check: Send a Radio Check Message to the specified Transceiver and let
the Transceiver send an ACK.
50
Menu Mode:
1 Select “RMT CTRL” and press the [ S ] button to enter Remote Control Mode.
2 Press the [ <B ] and [ C> ] buttons to select Unit ID List.
3 Press the [ S ] button to enter Remote Control Message Selection.
4 Press the [ <B ] and [ C> ] buttons to select Remote Control Message.
5 Press the PTT switch to send selected Remote Control Message.
RX Audio Equalizer [NXDN/ DMR]
Allows you to set the receiving audio characteristic (Flat, High boost, or Low
boost).
Menu Mode:
1 Select “RX EQ” and press the [ S ] button.
2 Press the [ <B ] and [ C> ] buttons to select the audio characteristic.
3 Press the [ S ] button to confirm and exit mode.
Flat
Standard RX audio characteristic.
Treble range is emphasized. Audio sounds clearer and
becomes more understandable.
High boost
Treble range is suppressed and bass range is boosted that
makes the audio quality more natural.
Low boost
51
RX Auto Gain Control [NXDN/ DMR]
Allows you to set the transceiver to automatically adjust the volume of the
receiving sound to a specific level for easy listening.
Menu Mode:
1 Select “RX AGC” and press the [ S ] button.
2 Press the [ <B ] and [ C> ] buttons to select Off, Low, or High.
3 Press the [ S ] button to confirm and exit mode.
Save Log Data [Analog/ NXDN/ DMR]
This function saves the operation and communication logs of this transceiver.
•
This function is for field support use such for your dealer.
Scan [Analog/ NXDN/ DMR]
Allows you starting or stopping scan.
PF Button:
Press the programmed button to start scanning. To stop scanning, press this
button.
Menu Mode:
Select “SCAN” and press the [ S ] button to activate/ deactivate the Scan.
•
The “
” indicator appears on the display.
•
The “
” indicator blinks while paused.
52
Scan Delete/Add [Analog/ NXDN/ DMR]
Allows you to include or omit each channel in the scan sequence.
1 Select your desired channel.
2 PF Button: Press the programmed button to change the Scan Delete/Add
status of the channel.
Menu Mode: Select “SCN D/A” and press the [ S ] button to activate/
deactivate the Scan of the channel.
•
When a channel is added to scan, Beep A (1 beep) sounds and the “
(right side) indicator appears on the display.
”
•
When a channel is deleted (not include in scan), Beep B (2 beeps) sounds
and the “ ” (right side) indicator disappears on the display.
Scrambler/Encryption [Analog/ NXDN/ DMR]
Enables or disables Scrambler (analog) or Encryption (NXDN/ DMR) function.
•
Voice Scrambler is the function to scramble the audio signal so that the
contents of communications can be prevented from being intercepted.
•
Encryption is the function that enhances secrecy in communications on the
digital channels by encrypting voice data.
PF Button:
Press the programmed button to activate the Scrambler/Encryption.
•
Beep A (1 beep) sounds.
Press this button again to deactivate Scrambler/Encryption.
Beep B (2 beeps) sounds.
•
Menu Mode:
Select “SCRENC” and press the [ S ] button to activate/ deactivate the Scrambler/
Encryption.
•
The “ ” indicator appears while Scrambler/Encryption is activated.
53
Scrambler/Encryption Code [Analog/ NXDN/ DMR]
Allows you to change the Scrambler Code/ Encryption Key used in the
transmission.
1 PF Button: Press and hold the programmed button to enter Scrambler/
Encryption Code Mode.
Menu Mode: Select “SCRENC C” and press the [ S ] button to enter
Scrambler/Encryption Code Mode.
2 Press the [ <B ] and [ C> ] buttons to select the Scrambler Code or Encryption
Key.
•
Must be set to the same code/key for transmission and reception.
Scrambler Code
Encryption Key
3 Press the [ S ] button to confirm and exit mode.
54
Send the GPS Data [Analog/ NXDN/ DMR]
Allows you to send your positioning data to the base station when a GPS speaker/
microphone has been installed.
•
When the power is turned ON and/or the reception condition of the GPS
satellite is poor, positioning may take longer to complete.
PF Button:
Press the programmed button to send GPS data.
•
Beep A (1 beep) sounds.
Menu Mode:
Select “SEND GPS” and press the [ S ] button to send GPS data.
•
When GPS data transmission is completed and "COMPLETE" is displayed for
1 second.
Short Message Mode [NXDN/ DMR]
Allows you to send short messages such as an address, telephone number, etc.
1 PF Button: Press the programmed button to enter Short Message Mode.
Menu Mode: Select “SDM MODE” and press the [ S ] button to enter Short
Message Mode.
2 Press the [ <B ] and [ C> ] buttons to select a Short Message from the list
(NXDN/ DMR).
3 Press the PTT switch or Side 2 button to send short messages.
Speaker Attenuation [Analog/ NXDN/ DMR]
Temporarily reduce the volume level of the speaker of the transceiver and
speaker/ microphone.
PF Button:
Press the programmed button to change the Speaker Attenuation On or Off.
55
Speaker Type [NXDN/ DMR]
Allows you to configure the type of the external speaker and speaker/ microphone
to be connected to the transceiver and enables the optimal conditions of the audio
quality.
Menu Mode:
1 Select “SPK TYPE” and press the [ S ] button.
2 Press the [ <B ] and [ C> ] buttons to select the speaker type.
•
You can select from None (without adjusting the audio characteristics),
SPK 1 to SPK 11.
3 Press the [ S ] button to confirm and exit mode.
Type
SPK 1
SPK 2
SPK 3
Model
KMC-45*, KMC-45D
KMC-48GPS*
KMC-21
KHS-7, KHS-7A*, KHS-8BL, KHS-8BE, KHS-9BL, KHS-9BE,
KHS-21*, KHS-22, KHS-22A, KHS-25, KHS-26, KHS-27, KHS-27A,
KHS-31, KHS-31C
SPK 4
SPK 5
SPK 6
SPK 7
SPK 8
SPK 9
KHS-23, KHS-35F
KHS-10-BH*, KHS-10-OH*, KHS-10D-BH, KHS-10D-OH
EMC-11, EMC-12
KHS-1*
KHS-29F
SPK 10 KEP-2
SPK 11 KHS-8NC
* : Not support for DMR.
56
Squelch Level [Analog]
Allows you to adjust the transceiver squelch level.
1 PF Button: Press the programmed button to enter Squelch Level Adjustment
Mode.
Menu Mode: Select “SQL LVL” and press the [ S ] button to enter Squelch
Level Adjustment Mode.
2 Press the [ <B ] and [ C> ] buttons to increase and decrease the squelch level
from 0 (open) to 9 (tight).
3 Press the [ S ] button to confirm and exit mode.
Squelch Off [Analog/ NXDN/ DMR]
Allows you to turn the transceiver squelch off, to better hear weak signals on the
channel.
PF Button:
Press the programmed button to activate/ deactivate the Squelch Off.
Menu Mode:
Select “SQL OFF” and press the [ S ] button to activate/ deactivate the Squelch
Off.
•
The “ ” indicator appears while Squelch Off is activated.
Squelch Off Momentary [Analog/ NXDN/ DMR]
PF Button:
Press and hold the programmed button to momentarily turn the transceiver
squelch off. Releasing this button turns the transceiver squelch back on. While
squelch is off, you can better hear weak signals on the channel.
57
Stack [Analog/ NXDN/ DMR]
Allows you to check the records of received calls and messages received.
•
•
The “ ” indicator lights up when all stacked data is already read.
When there is unread data, The “ ” indicator blinks.
1 PF Button: Press the programmed button to enter Stack Mode.
Menu Mode: Select “STACK” and press the [ S ] button to enter Stack Mode.
•
If the stack is empty, “EMPTY” is displayed for 1 second and Stack Mode is
not entered.
2 Press the [ <B ] and [ C> ] buttons to change the category display Caller ID
List or Message List.
Caller ID
Message List
•
•
Select “CALL ID” and press the [ S ] button. The stacked Caller ID data is
displayed.
Select “MESSAGE” and press the [ S ] button. The stacked Status
Message data is displayed.
58
3 Press the [ <B ] and [ C> ] buttons to select the List.
•
Each time press the [ S ] button to change display type (Message → Caller
ID → Channel No.→ Message→ ).
•
Press the [A] button, delete confirmation is displayed, press the [S] button
to delete displayed Caller ID and Message.
•
Press and hold the [A] button, delete confirmation is displayed, press the
[S] button to delete all Caller IDs and Messages.
4 Press the Side 1 button to exit Stack Mode.
Status [Analog/ NXDN/ DMR]
Allows you to send status messages selected from the Status List.
1 PF Button: Press the programmed button to enter Status Mode.
Menu Mode: Select “STATUS” and press the [ S ] button to enter Status Mode.
2 Press the [ <B ] and [ C> ] buttons to select the status messages you want to
transmit.
3 Press the PTT switch or Side 2 button to send status messages.
59
Surveillance [Analog/ NXDN/ DMR]
Allows you to disable the alert tone, backlight and LED functions. The Surveillance
function is used when the change of the transceiver status needs to be kept
unnoticed, such as while on a Public Safety operation.
PF Button:
Press the programmed button to activate the Surveillance Mode.
•
•
Beep A (1 beep) sounds.
“SUR ON” is displayed for 1 second.
Press this button again to deactivate the Surveillance Mode.
•
•
Beep B (2 beeps) sounds.
“SUR OFF” is displayed for 1 second.
Menu Mode:
Select “SURVEIL” and press the [ S ] button to activate/ deactivate the
Surveillance Mode.
Talk Around [Analog/ NXDN/ DMR]
Talk Around redirects the transceiver signals directly to other party members
rather than relaying the signals through a repeater.
PF Button:
Press the programmed button to activate the Talk Around.
•
Beep A (1 beep) sounds.
Press this button again to deactivate the Talk Around.
Beep B (2 beeps) sounds.
•
Menu Mode:
Select “TALK ARD” and press the [ S ] button to activate/ deactivate the Talk
Around.
•
The “ ” indicator appears while Talk Around is activated.
Transceiver Password [Analog/ NXDN/ DMR]
Allows you to enter Transceiver Password Input Mode.
60
TX Audio Equalizer [NXDN/ DMR]
Allows you to set the transmission audio characteristic (Flat, High boost, or Low
boost).
Menu Mode:
1 Select “TX EQ” and press the [ S ] button.
2 Press the [ <B ] and [ C> ] buttons to select the audio characteristic.
3 Press the [ S ] button to confirm and exit mode.
Flat
Standard TX audio characteristic.
Treble range is emphasized. Audio sounds clearer and
becomes more understandable.
High boost
Treble range is suppressed and bass range is boosted that
makes the audio quality more natural.
Low boost
TX Auto Gain Control [NXDN/ DMR]
Allows you to set the transceiver to automatically adjust the internal and external
microphone sensitivity for easy listening.
Menu Mode:
Select “TX AGC” and press the [ S ] button to change the TX Auto Gain Control
On or Off.
61
VOX [Analog/ NXDN/ DMR]
Allows you to adjust the VOX Gain level.
1 PF Button: Press the programmed button to enter VOX Gain Level Adjustment
Mode.
Menu Mode: Select “VOX LVL” and press the [ S ] button to enter VOX Gain
Level Adjustment Mode.
2 Press the [ <B ] and [ C> ] buttons to increase and decrease the VOX Gain
level from 1 (low) to 10 (high).
3 Press the [ S ] button to confirm and exit mode.
VOX Function [Analog/ NXDN/ DMR]
VOX (VOX/ Semi-VOX) operation allows you to transmit hands-free. This feature
can be activated or deactivated by your dealer. To operate VOX, you must use an
optional headset.
PF Button:
Press and hold the programmed button to switch the VOX operation On.
•
Beep A (1 beep) sounds.
Press this button again to switch the VOX operation Off.
Beep B (2 beeps) sounds.
•
Menu Mode:
Select “VOX” and press the [ S ] button to switch the VOX operation On or Off.
•
When VOX is On, the “ ” indicator appears on the display.
•
When VOX is Off, the “ ” indicator disappears on the display.
62
Zone Delete/Add [Analog/ NXDN/ DMR]
Allows you to include or omit each Zone in the Multi-Zone scan sequence.
1 Select your desired zone.
2 PF Button: Press the programmed button to switch the Zone Delete/Add
status of the channel.
Menu Mode: Select “ZONE D/A” and press the [ S ] button to switch the Zone
Delete/Add status of the channel.
•
When a zone is added to scan, Beep A (1 beep) sounds and the “
(left side) indicator appears on the display.
”
•
When a zone is deleted (not include in scan), Beep B (2 beeps) sounds
and the “ ” (left side) indicator disappears on the display.
Zone Select [Analog/ NXDN/ DMR]
Selector:
Turn the Selector to select the zone number.
Zone Up/Down [Analog/ NXDN/ DMR]
Selector:
Turn the Selector to increase/ decrease the zone number.
Zone Up/ Zone Down [Analog/ NXDN/ DMR]
PF Button:
Press the programmed button to increase/ decrease the zone number.
Zone Up (Continuous)/ Zone Down (Continuous)
[Analog/ NXDN/ DMR]
PF Button:
Hold down the programmed button to continuously increase/ decrease the zone
number.
63
KEYPAD OPERATION
The keypad operating method can be selected according to the purpose.
Even pressing the [ 0 ] ~ [ 9 ], [ ], [ # ] button, and
button-entry Error Tone will sound and no operation will be
None
performed.
Press the [ 0 ] ~ [ 9 ] button to enter Channel Entry Mode
and keypad input state.
The following are examples for entering a channel number
by using the keypad.
•
If the maximum channel number has 1 digit:
- To make a call on channel 7, press the [ 7 ] button.
If the maximum channel number has 2 digits:
•
- To make a call on channel 90, press the [ 9 ] and [ 0 ]
buttons in this order.
- To make a call on channel 7, press the [ 0 ] and [ 7 ]
Channel Entry
buttons in this order.
•
If the maximum channel number has 3 digits:
- To make a call on channel 250, press the [ 2 ], [ 5 ]
and [ 0 ] buttons in this order.
- To make a call on channel 90, press the [ 0 ], [ 9 ]
and [ 0 ] buttons in this order.
- To make a call on channel 7, press the [ 0 ], [ 0 ] and
[ 7 ] buttons in this order.
If the maximum number of digits is entered, the transceiver
exits Channel Entry Mode and then migrates to the channel
of the entered channel number.
Press and hold the [ 1 ] ~ [ 9 ] button for 1 second, and OST
will be On and OST List number 1 to 9 are selected.
•
Press and hold the [ 0 ] button for 1 second, and OST
will be On and OST List number 1 to 9 are selected.
OST
•
Press and hold the [ ] button for 1 second, and
Shortcut input of OST List will be appeared.
Press the [ 0 ] ~ [ 9 ] button to enter Autodial Mode.
•
If Store and Send is Disabled, Keypad is entered with
Autodial Mode (List Selection).
Autodial
•
If Store and Send is Enabled, press [ 0 ] ~ [ 9 ], [ ], [ # ]
button is input with Autodial Mode (Manual input).
64
This function allows you to send DTMF by pressing Keypad
without PTT switch.
•
•
•
If DTMF Manual Dialing is Enabled, the DTMF Code is
sent by pressing the [ 0 ] ~ [ 9 ], [ ], [ # ] button.
Press the [ 0 ] ~ [ 9 ], [ ], [ # ] button, send the DTMF
Code of the pressed button.
When the button is release, the modulation of DTMF
Code will stop, but unmodulated transmission will
continue for the time set by DTMF Hold Time.
Keypad Auto PTT
Press the [ 0 ] ~ [ 9 ] button to enter the Status Mode and
keypad input state.
Status
Press the [ 0 ] ~ [ 9 ] button to enter the Short Message
Mode and keypad input state.
Press the [ 0 ] ~ [ 9 ] button to enter the Individual Call
Mode or Selcall Mode and keypad input state.
Press the [ 0 ] ~ [ 9 ] button to enter the Individual Call
Mode or Selcall Mode and keypad input state.
Short Message
Individual
Individual +
Status
•
Similar to pressing the PF button for [Individual +
Status], press the [ S ] button in Individual Call Mode to
enter the Status Mode.
Press the [ 0 ] ~ [ 9 ] button to enter the Individual Call
Mode or Selcall Mode and keypad input state.
Individual + Short
Message
•
Similar to pressing the PF button for [Individual + Short
Message], press the [ S ] button in Individual Call Mode
to enter the Short Message Mode.
Press the [ 0 ] ~ [ 9 ] button to enter the Group Call Mode or
Selcall Mode and keypad input state.
Group
Press the [ 0 ] ~ [ 9 ] button to enter the Group Call Mode or
Selcall Mode and keypad input state.
Group + Status
•
Similar to pressing the PF button for [Group + Status],
press the [ S ] button in Group Call Mode to enter the
Status Mode.
Press the [ 0 ] ~ [ 9 ] button to enter the Group Call Mode or
Selcall Mode and keypad input state.
Group + Short
Message
•
Similar to pressing the PF button for [Group + Short
Message], press the [ S ] button in Group Call Mode to
enter the Short Message Mode.
65
FUNCTION DESCRIPTIONS
For details on functions that are not included in “FUNCTIONS OVERVIEW” {p.
23} and “FUNCTION DESCRIPTIONS”, please consult your dealer.
TRANSCEIVER PASSWORD
LCD Model
If the transceiver is password protected, “PASSWORD” will appear on the
display when the power is turned on. To unlock the transceiver, enter the correct
password.
1 Press the button programmed as [Transceiver Password] to enter Transceiver
Password Mode.
•
Alternatively, press the button programmed as [Menu] to enter Transceiver
Password Mode using the Menu Mode.
•
If a password has been registered and the [Transceiver Password]
function has not been programmed to a button or configured to the menu,
the transceiver enters Transceiver Password Mode when the power is
turned on.
2 Enter a number using the [ <B ] and [ C> ] buttons.
•
On full button model, you can enter the password directly by pressing the
keypad.
3 Press the [ S ] or [ ] button to accept the number.
4 Repeat steps 2 and 3 to enter the entire password.
•
Press the [ A ] or [ # ] button to delete an incorrectly entered number.
Press and hold the [ A ] or [ # ] button to delete all numbers.
5 Press the [ S ] or [ ] button to confirm the entry.
•
If you enter an incorrect password, an error tone sounds and the
transceiver remains locked, the transceiver will return to "PASSWORD"
display.
•
The password can contain a maximum of 6 digits.
66
Non-LCD Model
If your transceiver is password protected, the LED will light blue when you turn the
transceiver ON. Enter the password (up to 6 digits) using the following procedure.
1 Set the Selector to position “1”.
2 Press the Side 1 or Side 2 button to enter the first digit.
•
The Side 1 button increases the digit value and the Side 2 button
decreases it. The transceiver announces the digit number as it changes.
3 Repeat step 2 for Selector positions 2 ~ 6.
•
If there are less than 6 password digits, repeat for only the number of digits
the password contains.
4 Press the PTT switch to confirm the password.
When the correct password is entered, the Blue LED turns off.
•
67
SCAN
Scan is useful for monitoring signals on the transceiver channels. While scanning,
the transceiver checks for a signal on each channel and only stops on a channel if
a signal is present.
To begin scanning, press the button programmed as [Scan].
•
•
•
•
The “
” indicator appears on the display.
If programmed by your dealer, the LED indicator blinks during scanning.
The channels are scanned.
When a signal is detected on a channel, Scan pauses on that channel. The
transceiver will remain on the busy channel until the signal is no longer
present. When the signal “drops out”, the transceiver will remain on the
channel momentarily before Scan resumes. This delay time is programmed
by your dealer. If a signal is received during the delay time, the transceiver will
remain on the same channel.
To stop scanning, press the [Scan] button again.
Note:
◆ In order for Scan to operate, there must be at least 2 channels added to the
scanning sequence. If there are less channels than this, Scan will not operate.
TEMPORARY CHANNEL LOCKOUT
During scan, you can temporarily remove specific channels from the scanning
sequence by selecting them and pressing the button programmed as [Scan
Delete/Add].
•
The “
channel.
” (right side) indicator no longer appears on the display for that
•
The channel is no longer scanned. However, when scanning is ended and
restarted, the channels will reset and the channel will again be in the scanning
sequence.
PRIORITY SCAN
A Priority channel must be programmed in order for Priority Scan to function.
When using a single Priority channel, the transceiver will automatically change to
the Priority channel when a call is received on it, even if a call is being received on
a normal channel.
When using dual Priority channels, Priority channel 1 is given precedence over
Priority channel 2. So, if a call is received on Priority channel 1 while a call is
already on Priority channel 2, the transceiver will automatically change to Priority
channel 1.
•
The “
” indicator appears on the display when the channel is Priority
channel.
68
SCAN REVERT
The Scan Revert channel is the channel selected when you press the PTT switch
to transmit during scan.Your dealer can program one of the following Scan Revert
channels:
•
•
Selected: The last channel selected is assigned as the new revert channel.
Selected + Talkback: If the channel has been changed, the newly selected
channel is assigned as the new revert channel. The transceiver “talks back” on
the current channel.
•
•
Priority 1/ Priority 2: If your dealer has programmed a Priority channel (either
Priority 1 or Priority 2), this channel is the revert zone-channel.
Priority 1 + Talkback/ Priority 2 + Talkback: If your dealer has programmed
a Priority channel (either Priority 1 or Priority 2), this channel is the revert
zone-channel. The transceiver “talks back” on the current receive channel.
•
Last Called + Selected: The last channel on which you received a call is
assigned as the new revert channel. The transceiver “talks back” on the
current channel. If the channel has been changed, the newly selected channel
is assigned as the new revert channel.
69
DTMF (DUAL TONE MULTI FREQUENCY) CALLS
Note:
◆ Manual Dialing and Keypad Auto PTT are available only on full button model.
MAKING A DTMF CALL
Manual Dialing
1 Press and hold the PTT switch.
2 Enter the desired digits using the keypad.
•
•
The corresponding DTMF tones sound each time you press a button.
If you release the PTT switch, transmit mode will end even if the complete
number has not been sent.
Keypad Auto PTT
If your dealer has activated the Keypad Auto PTT function, simply press the
buttons on the keypad or microphone to make the call.
•
The DTMF code will be sent automatically when you press a button.
Store & Send
1 Enter the desired digits using the keypad.
•
•
The digits appear on the display as you enter them.
You can enter up to 34 digits before transmitting.
2 After entering the complete number, press the PTT switch to transmit.
Note:
◆ If you switch the power OFF before transmitting the number, the number will
be cleared.
Stun Code
This function is used when a transceiver is stolen or lost.
When the transceiver receives a call containing a stun code, either the transmit
mode or both the receive and transmit mode will be disabled. The stun code is
canceled when the transceiver receives a call with a revive code.
70
EMERGENCY CALLS
If your transceiver has been programmed with the Emergency function, you can
make emergency calls.
1 Press and hold the button programmed as [Emergency].
•
Depending on the delay time programmed into your transceiver, the length
of time you must hold the Emergency button will vary.
•
When the transceiver enters Emergency mode, the transceiver will change
to the Emergency channel and begin transmitting based on how the
transceiver is set up by your dealer. Transmit periods are also set by your
dealer.
2 To exit Emergency mode, press and hold the [Emergency] button again.
•
If the Emergency mode completes a preset number of cycles, Emergency
mode will automatically end and the transceiver will return to the zone and
channel that was in use before Emergency mode was entered.
Note:
◆ Your dealer can set the transceiver to emit a tone when Emergency mode
starts and stops.
◆ Your dealer can set the transceiver to emit tones and received signals as
normal or mute the speaker during Emergency operation.
71
SCRAMBLER (ANALOG)/ ENCRYPTION (NXDN/ DMR)
Note:
◆ The following types of encryption are available depending on the protocol
used.
NXDN : Bit scrambling (built-in encryption function)
DMR : Bit scrambling (built-in encryption function) and Enhanced Encryption
◆ The Enhanced Encryption is a software option. Ask your dealer for details
concerning the Enhanced Encryption settings.
SECURE (ENCRYPTED) TRANSMISSION
Press the button programmed as [Scrambler/Encryption] to switch the
transceiver to secure (encrypted) transmission.
•
Alternatively, press the button programmed as [Menu] to enter Scrambler/
Encryption Mode using the Menu Mode.
•
The Scrambler/Encryption indicator “ ” appears when the function is turned
ON.
•
Pressing the PTT switch after the Scrambler or Encryption function has been
turned ON encrypts the transmitted signal.
SELECTING THE SCRAMBLER CODE
1 Press the button programmed as [Scrambler/Encryption Code] to enter
Scrambler/Encryption Code Mode.
•
Alternatively, press the button programmed as [Menu] to enter Scrambler/
Encryption Code Mode using the Menu Mode.
2 Press the [ <B ] and [ C> ] buttons to increase or decrease the Scrambler
code.
•
Up to 16 Scrambler codes can be used.
3 Press the [ S ] button to set the new Scrambler code.
72
SELECTING THE ENCRYPTION KEY
1 Press the button programmed as [Scrambler/Encryption Code] to enter
Scrambler/Encryption Code Mode.
•
Alternatively, press the button programmed as [Menu] to enter Scrambler/
Encryption Code Mode using the Menu Mode.
2 Select the new Encryption key using the [ <B ] and [ C> ] buttons.
•
Up to 16 Encryption keys can be used. One of these keys will be used
during transmission.
3 Press the [ S ] button to set the new Encryption key.
73
SIGNALING
QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT) [ANALOG]
Your dealer may have programmed QT or DQT signaling on your transceiver
channels. A QT tone/ DQT code is a sub-audible tone/ code which allows you to
ignore (not hear) calls from other parties who are using the same channel.
When a channel is set up with a QT tone or DQT code, squelch will only open
when a call containing a matching tone or code is received. Likewise, signals that
you transmit will only be heard by parties whose QT/ DQT signaling matches your
transceiver.
If a call containing a different tone or code is made on the same channel you
are using, squelch will not open and you will not hear the call. This allows you to
ignore (not hear) these calls. Although it may seem like you have your own private
channel while using QT/ DQT, other parties can still hear your calls if they set up
their transceiver with the same tone or code.
Operator Selectable Tone (OST) [Analog]
If a button has been programmed with [Operator Selectable Tone], you can
reprogram the QT tone or DQT code on each of your channels by OST List.
1 Select your desired channel.
2 Press and hold the button programmed as [Operator Selectable Tone].
•
Alternatively, you can press the button programmed as [Menu] to enter
OST Mode using the Menu Mode.
3 Press the [ <B ] and [ C> ] buttons to select your desired tone or code from 1
to 40.
4 Press the [ S ] button to save your new setting.
•
After selecting and setting up your desired tone or code, press the
[Operator Selectable Tone] button to activate the OST function. Press this
button again to turn the OST function off.
RADIO ACCESS NUMBER (RAN) [NXDN]
RAN is a signaling system designed for NXDN digital radio communications.
When a channel is set up with a RAN, squelch will only open when a call
containing a matching RAN is received. If a call containing a different RAN is
made on the same channel you are using, you will not hear the call. This allows
you to ignore (not hear) calls from other parties who are using the same channel.
COLOR CODE (CC) [DMR]
Color Code is a digital signaling for DMR protocol to enable smooth
communication among groups using the same channel.
74
OPTIONAL SIGNALING
Your dealer may also program several types of optional signaling for your
transceiver channels.
5-tone Signaling [Analog]
DTMF Signaling [Analog]
DTMF Signaling opens the squelch only when the transceiver receives a call
containing a matching DTMF code.
MDC-1200 Signaling [Analog]
MDC-1200 is a data system using Audio Frequency Shift Keying (AFSK).
FleetSync Signaling [Analog]
FleetSync Signaling opens the squelch only when the transceiver receives a
call that matches the FleetSync ID in FleetSync Signaling. Refer to “FleetSync:
NXDN ID Signaling [NXDN]
NXDN ID is an optional signaling system available only for digital communications.
75
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION
FleetSync is an Alphanumeric 2-way Paging Function, and is a protocol owned by
JVCKENWOOD Corporation. FleetSync enables a variety of paging functions on
your transceiver, some of which depend on dealer programming.
Note:
◆ This function is available only in analog operation.
SELCALL (SELECTIVE CALLING)
A Selcall is a voice call to a station or group of stations.
Transmitting
1 Select your desired zone and channel.
2 Press the button programmed as [Individual]/ [Individual + Status]/
[Individual + Short Message]/ [Group]/ [Group + Status]/ [Group + Short
Message] to enter Selcall Mode.
•
Alternatively, press the button programmed as [Menu] to enter Selcall
Mode using Individual/ Individual + Status/ Individual + Short Message/
Group/ Group + Status/ Group + Short Message in the Menu Mode.
3 Press the [ <B ] and [ C> ] buttons to select the station you want to call.
4 Press the PTT switch and begin your conversation.
Receiving
An alert tone will sound and the transceiver will enter Selcall mode. The calling
station’s ID will appear when a Selcall is received.You can respond to the call by
pressing the PTT switch and speaking into the microphone.
76
Identification Codes
An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number.
Each transceiver has its own ID.
•
•
•
•
Enter a Fleet number (100 ~ 349) to make a fleet call.
Enter an ID number (1000 ~ 4999) to make an individual call in your fleet.
Enter a Group ID (which is programmed in the FPU) to make a group call.
Enter a Fleet number followed by an ID number to make an individual call in
your desired fleet (Inter-fleet call).
•
•
Select “ALL” Fleet and “ALL” ID to make a call to all units (Broadcast call).
Select “ALL” Fleet and enter an ID number to make a call to the selected ID in
all fleets (Supervisor call).
STATUS MESSAGE
You can send and receive 2-digit Status messages which may be decided in
your talk group. Messages can contain up to 8 alphanumeric characters. Status
messages range from 10 to 99 (80 ~ 99 are reserved for special messages).
A maximum of 32 received messages can be stored in the stack memory of your
transceiver. These saved messages can be reviewed after reception. Depending
on your dealer settings, when the stack memory is full, either the oldest message
will be erased when a new message is received or the new message will not be
stored in the stack memory. The “ ” indicator appears when a message is stored
in the stack memory.
Transmitting
1 Select your desired zone and channel.
2 Press the button programmed as [Status] to enter Status Mode (proceed to
step 5), or [Individual + Status]/ [Group + Status] to enter Selcall Mode
(proceed to step 3).
3 Press the [ <B ] and [ C> ] buttons to select the station you want to call.
4 Press the [ S ] button to enter Status Mode.
5 Press the [ <B ] and [ C> ] buttons to select the status you want to transmit.
6 Press the PTT switch or Side 2 button to send Status messages.
•
“COMPLETE” appears on the display when the status has been
successfully transmitted.
Receiving
The “ ” indicator will flash and a calling ID or text message will appear when a
Status call is received. Press any button to return to normal operation.
77
SHORT MESSAGES
This transceiver can receive short data messages which contain a maximum of 48
characters.
GPS REPORT
GPS data can be manually transmitted by pressing the button programmed as
[Send the GPS Data], or by accessing the Menu. If set up by your dealer, GPS
data may be automatically transmitted at a preset time interval.
•
When using the GPS function, you must first connect the GPS speaker/
microphone.
•
When the power is turned ON and/or the reception condition of the GPS
satellite is poor, positioning may take longer to complete.
78
5-TONE SIGNALING
5-tone Signaling is enabled or disabled by your dealer. This function opens the
squelch only when the transceiver receives the 5 tones programmed in your
transceiver. Transceivers that do not transmit the correct tones will not be heard.
SELCALL (SELECTIVE CALLING)
A Selcall is a voice call to a station or group of stations.
Transmitting
1 Select your desired zone and channel.
2 Press the button programmed as [Individual]/ [Individual + Status]/
[Individual + Short Message]/ [Group]/ [Group + Status]/ [Group + Short
Message] to enter Selcall Mode.
•
Alternatively, press the button programmed as [Menu] to enter Selcall
Mode using Individual/ Individual + Status/ Individual + Short Message/
Group/ Group + Status/ Group + Short Message in the Menu Mode.
3 Press the [ <B ] and [ C> ] buttons to select the station you want to call.
4 Press the [ S ] button to complete the entry.
5 Press the button programmed as [Call 1] to [Call 6] and begin your
conversation.
Note:
◆ You can also use the buttons programmed as [Digit 1x Down], [Digit 1x Up],
[Digit 10x Down], and [Digit 10x Up] to adjust the Selcall number. [Digit 1x
Up] and [Digit 1x Down] increases and decreases the Selcall number by 1
respectively each time the button is pressed. [Digit 10x Up] and [Digit 10x
Down] increases and decreases the Selcall number by 10 respectively each
time the button is pressed.
Receiving
When a call containing the correct tones is received, the transceiver will enter
decode condition. An alert tone will sound and the calling station’s ID appears on
the display.
Press any button to return to normal operation.
79
STATUS MESSAGE
You can send and receive Status messages which may be decided in your talk
group. Messages can contain up to 8 alphanumeric characters.
A maximum of 32 received messages can be stored in the stack memory of your
transceiver.
Transmitting
1 Select your desired zone and channel.
2 Press the button programmed as [Status] to enter Status Mode (proceed to
step 5), or [Individual + Status]/ [Group + Status] to enter Selcall Mode
(proceed to step 3).
3 Press the [ <B ] and [ C> ] buttons to select the station you want to call.
4 Press the [ S ] button to enter Status Mode.
5 Press the [ <B ] and [ C> ] buttons to select the status you want to transmit.
6 Press the [ S ] button to complete the entry.
7 Press the button programmed as [Call 1] to [Call 6] to initiate the call.
Receiving
The “ ” indicator will flash and a calling ID or text message will appear when a
Status call is received.
Press any button to return to normal operation.
80
VOICE OPERATED TRANSMISSION (VOX)
VOX (VOX/ Semi-VOX) operation allows you to transmit hands-free. This feature
can be activated or deactivated by your dealer. To operate VOX, you must use an
optional headset.
VOX Type
VOX: When the voice level to the microphone is higher than the reference level
(VOX Gain Level), the transceiver automatically starts transmission.
Semi-VOX: Transmission is started by pressing PTT switch and transmission
continues while speaking even after PTT switch is released.
The Semi-VOX function is effective in the following cases.
•
Incorrect transmission due to noise.
•
Voice at start of transmission is interrupted.
VOX Operation
1 Connect a headset to the transceiver.
•
The VOX function does not activate when a headset is not connected to
the accessory terminal of the transceiver.
2 Press the button programmed as [VOX Function].
•
Alternatively, you can press the button programmed as [Menu] to enter
VOX Mode using the Menu Mode.
•
Beep A (1 beep) sounds and the “ ” indicator appears on the display.
3 To transmit, simply speak to the microphone.
4 When you finish speaking, transmission ends.
To turn the VOX function OFF, press the button programmed as [VOX Function]
button again.
•
Beep B (2 beeps) sounds and the “ ” indicator will disappear from the
display.
Note:
◆ The VOX Gain Level is set to a sensitive level, signal received with loud
volume may cause the transceiver to transmit.
81
Semi-VOX Operation
1 Connect a headset to the transceiver.
•
The VOX function does not activate when a headset is not connected to
the accessory terminal of the transceiver.
2 Press the button programmed as [VOX Function].
•
Alternatively, you can press the button programmed as [Menu] to enter
VOX Mode using the Menu Mode.
•
Beep A (1 beep) sounds and the “ ” indicator appears on the display.
3 To transmit, press the PTT switch.
4 Release the PTT switch.
5 Transmission continues while speaking.
6 When you finish speaking, transmission ends.
To turn the Semi-VOX function OFF, press the button programmed as [VOX
Function] button again.
•
Beep B (2 beeps) sounds and the “ ” indicator will disappear from the
display.
VOX Gain Level
Sets the Microphone input sensitivity of the VOX operation.
1 Connect a headset to the transceiver.
2 Press the button programmed as [VOX].
•
The current VOX Gain level appears on the display.
3 Press the [ <B ] or [ C> ] button to increase or decrease the VOX Gain level.
The VOX Gain can be adjusted from levels 1 to 10.
•
4 While adjusting the level, speak into the headset microphone to test the
sensitivity level. (Your voice is not transmitted during this test procedure.)
•
When sound is recognized, the LED lights yellow.
5 Press the [ S ] button to save your new setting.
82
BACKGROUND OPERATIONS
TIME-OUT TIMER (TOT)
The Time-out Timer is used to prevent any caller from using a channel for an
extended period of time.
If you continuously transmit for a period of time that exceeds the programmed
time, the transceiver will stop transmitting and an alert tone will sound. To stop the
tone, release the PTT switch.Your dealer can program the TOT time in the range
of 15 seconds to 20 minutes.
If programmed by your dealer, a pre-alert tone will sound before the timer expires.
Also, if programmed by your dealer, you may have to wait for a short duration
before you can continue to transmit. If you press the PTT switch before the timer
has been reset, an alert tone will sound and the transceiver will not enter transmit
mode.
BATTERY SAVER
The Battery Saver extends the battery life by reducing the battery consumption
through intermittent monitoring of the presence of signals while on standby.
LOW BATTERY WARNING
Low Battery Warning alerts you when the battery needs to be recharged.Your
dealer can set an alert tone to sound and the LED indicator to blink red when the
battery power is low.
When the battery power is very low, recharge or replace the battery pack.
SIGNAL STRENGTH INDICATOR
The signal strength indicator displays the strength of received calls.
: Strong signal
: Sufficient signal
: Weak signal
: Very weak signal
83
VOICE ANNOUNCEMENT
An audio voice will be announced as below by dealer setting.
•
When changing the zone and/or channel, the new zone and channel number
are announced.
•
When changing the function setting, the new setting is announced.
- Scrambler/Encryption
- VOX Function
- Home Channel
- Button Lock
- Low Transmit Power
- Scan
- Send the GPS Data
- Speaker Attenuation
- Talk Around
84
BUSY CHANNEL LOCKOUT (BCL)
If BCL is set up by your dealer, you will be unable to transmit on the channel if it
is already in use. Under these circumstances, use a different channel or wait until
the channel becomes free. However, if BCL Override has also been programmed,
you can transmit over the current signal:
1 Press and hold the PTT switch.
•
If the channel is already in use, a warning tone will sound.
2 Release the PTT switch, then press and hold the PTT switch again within half
a second.
3 Speak to the microphone as you would during a normal call.
The transceiver transmits according to the configuration in Busy Channel Lockout
by dealer.
In Analog System
Carrier Only
The transceiver cannot transmit when carrier is received.
The transceiver cannot transmit when the selected channel
is busy and QT/DQT is unmatched.
Incorrect Tone
The transceiver cannot transmit when the selected channel
is busy before valid Optional Signaling matches or when the
selected channel is busy and the programmed QT/DQT is
not detected before valid Optional Signaling matches.
Optional
Signaling
In NXDN System
Carrier Only
The transceiver cannot transmit when carrier is received.
The transceiver cannot transmit when the received RAN
and the RAN set in the channel is unmatched.
Incorrect RAN
Correct RAN
The transceiver cannot transmit when the received RAN
and the RAN set in the channel are matched.
The transceiver cannot transmit while receiving RAN
regardless of whether or not it matches with the RAN set in
the channel.
Any RAN
In DMR System
Carrier Only
The transceiver cannot transmit when carrier is received.
The transceiver cannot transmit when the received Color
Code and the Color Code set in the channel are matched.
Correct CC
85
NX-1200-E
NX-1200-E2
NX-1200-E3
NX-1300-E
NX-1300-E2
NX-1300-E3
136.000 - 174.000 MHz 400.000 - 470.000 MHz
Frequency Range (TX/RX)
Maximum Output Power
5 W
Operating Temperature Range
–30°C - +60°C
The device complies with RF exposure requirement.
© 2021
|