KENWOOD KTC D600E User Manual

KTC-D600E  
DIGITAL TV TUNER  
INSTRUCTION MANUAL  
© B64-4758-08/00 (E)  
Safety precautions  
Notes  
To select TV Type (PAL or NTSC)  
WARNING  
The TV picture display can be divided roughly into  
two TV formats (PAL and NTSC). They are variable  
depending on countries and areas. This unit has a  
function for changing the video format according  
to the TV type. Please confirm to set the Type switch  
according to the type of your TV type.  
To prevent injury or fire, take the following  
precautions:  
To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools) inside  
the unit.  
Installation Procedure  
1 To prevent short circuits, remove the key from the  
ignition and disconnect the terminal of the  
battery.  
PAL  
NTSC  
Change NTSC/PAL setting only when the device is  
turned off.  
2 Make the proper input and output wire connections  
for each unit.  
3 Connect the wire on the wiring harness.  
4 Connect the wiring harness connector to the unit.  
5 Install the unit in your car.  
6 Reconnect the terminal of the battery.  
7 Press the reset button.  
How to reset your unit  
If the unit fails to operate properly, press the Reset  
button.  
It is used for the purpose of software update.  
• Mounting and wiring this product requires skills and  
experience. For safety’s sake, leave the mounting and wiring  
work to professionals.  
Reset button  
• Make sure to ground the unit to a negative 12V DC power  
supply.  
• Do not install the unit in a spot exposed to direct sunlight or  
excessive heat or humidity. Also avoid places with too much  
dust or the possibility of water splashing.  
• Do not use your own screws. Use only the screws provided. If  
you use the wrong screws, you could damage the unit.  
• Make sure that all wire connections are securely made by  
inserting jacks until they lock completely.  
• If your vehicle’s ignition does not have an ACC position, or  
if the ignition wire is connected to a power source with  
constant voltage such as a battery wire, the power will not be  
linked with the ignition (i.e., it will not turn on and off along  
with the ignition). If you want to link the unit’s power with  
the ignition, connect the ignition wire to a power source that  
can be turned on and off with the ignition key.  
• Use a commercially available conversion connector if the  
connector does not fit in the vehicle connector.  
• Insulate unconnected wires with vinyl tape or other similar  
material. To prevent a short circuit, do not remove the caps  
on the ends of the unconnected wires or the terminals.  
• If the fuse blows, first make sure the wires aren’t touching to  
cause a short circuit, then replace the old fuse with one with  
the same rating.  
• After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
English  
3
A
Basic Operation (When connected with DNX9260BT  
)
Various control screens appear in the Digital TV/ Video Source mode. (You can only operate Digital TV with the  
optional accessory Digital TV Tuner connected). Refer to the user manual for the connected monitor to see basic  
operations including how to convert to TV.  
Function During TV Screen  
Menu Control Screen  
Basic functions are available even when the TV  
screen is displayed.  
Menu Control Screen appears by touching the area  
shown below.  
1
2
Display the TV screen  
Operation on the TV screen  
1
3
4
2
1
Displays Menu Control Screen.  
2
Displays Easy Control Screen. *  
3
4
,
Selects a channel.  
* [SCRN], [], [] buttons shown on Easy Control Screen  
cannot be used.  
[Menu] Shows Setting Menu Screen.  
(Refer to page 5)  
[EPG] Shows EPG (Electric Program Guide) Screen.  
(Refer to page 13)  
[], [], [], [] Moves highlight in Setting Menu.  
[Enter] Executes selected Menu item.  
[Return] Returns to the previous screen.  
[Exit] Returns to Digital TV Screen.  
[Direct] Direct TV control by touching the screen.  
4
KTC-D600E  
Settings  
You can select following system setting items. Set the system by controlling the touch panel of the monitor.  
You can also operate the enclosed remote controller in the same way.  
Setting item  
“Search”  
Selectable setting/item  
System Setting  
1
Show Menu Control Screen by touching  
[Menu] button.  
“Automatic Search” Search for currently available stations and save  
them in the Channel List. (page 6)  
“Manual Search”  
Search a station by specifying area or channel. (page 6)  
2
Touch [] or [] button to select main item.  
Switching frequency” The function is for watching same broadcasting  
Main item  
service between several areas.  
Enable/Disable”  
Setting > Search  
“Search Area”  
The function is used to change a frequency table  
of each country.  
Search  
System  
Channel  
Preference  
Europe/Australia/Taiwan”  
Automatic Search  
Manual Search  
“Active Antenna DC” Active antenna is used, set to“Enable”(supplied  
to DC 5V).  
Enable/Disable”  
Switching frequency  
Search Area  
“System”  
“System Status”  
Active Antenna DC  
You can view the system information (Hardware,  
software and system version).  
“Reset Default”  
All setting values will be returned to the initial  
values. (page 8)  
3
Touch [] or [] button to select sub item  
and then press [Enter] button.  
“Software Update” Display the firmware version and update the  
firmware. For how to update the firmware, access  
our web site. (page 8)  
Setting > Search  
Search  
System  
Channel  
Preference  
“Common Interface” You can view the CA card information. Information  
will be displayed according to the CA card used.  
Automatic Search  
Manual Search  
“Channel”  
“Edit Channel”  
Switching frequency  
Search Area  
You can additional and edit the favorite channels.  
(page 7)  
Active Antenna DC  
“Preference”  
“Parental Control” You can set to censorship level and change to  
Sub item  
password. (page 9)  
“Language Setting” You can set to language for menu, Audio and  
subtitle. (page 10)  
4
Touch [] or [] button to select the value  
to set and then press [Enter] button.  
Menu Language/Audio Language/Subtitle  
Language: “English”/“German”/“Spanish”/  
“Italian”/“Dutch”/“Portugal”/“Finland”/  
“French”/“Russian”  
Setting > Switching frequency  
Enable  
Disable  
“Time Setting”  
“A/V Control”  
You need set to GMT (Greenwich mean time) Offset  
and Daylight Saving. (page 11)  
GMT Offset: “–12:00” — “0” — “+12:00”  
Daylight Saving:Enable/Disable”  
You can set to Audio output and Screen Ratio.  
Audio Outut: “Stereo”/“Left”/“Right”  
Screen Ratio: “4:3”/“16:9”  
This function provides 4:3 and 16:9 two ratio for  
user to select. If your display supports 4:3 screen  
format and selected channel provides 4:3 format  
program, select 4:3.  
5
Touch [Return] button when you are finished.  
(Factory setting: Underlined)  
English  
5
Settings  
Automatic Search  
(Searching for currently available station)  
Manual Search  
( Manually Searching Station)  
Search for currently available stations and save  
them in the Channel List.  
Search a station by specifying area or channel.  
1
Show Menu Control Screen by touching  
[Menu] button.  
1
Show Menu Control Screen by touching  
[Menu] button.  
2
3
Touch [] or [] button to select "Search".  
2
3
Touch [] or [] button to select "Search".  
Touch [] or [] button to select "Manual  
Search" and then press [Enter] button.  
Touch [] or [] button to select "Automatic  
Search" and then press [Enter] button.  
Setting > Search  
Setting > Search  
Search  
System  
Channel  
Preference  
Search  
System  
Channel  
Preference  
Automatic Search  
Manual Search  
Automatic Search  
Manual Search  
Switching frequency  
Search Area  
Switching frequency  
Search Area  
Active Antenna DC  
Active Antenna DC  
4
Touch [] or [] button to select frequency  
and then press [Enter] button.  
Setting > Automatic Search  
Search > Manual Search  
Frequency  
Scan Status  
Found Channels  
Frequency 177.5 MHz  
177.5 MHz (7MHz)  
Bandwidth  
Found TV NO  
Found Radio NO  
Found Total NO  
7MHz  
0
177.5 MHz (8MHz)  
184.5 MHz (7MHz)  
186.0 MHz (8MHz)  
191.5 MHz (7MHz)  
0
0
Channel search is performed and the available  
channel is saved in the channel list.  
5
Touch [Return] button when you are finished.  
4
Touch [Return] button when you are finished.  
• Manual search is for advanced users and offers the  
ability to search for specific channels. Regular users are  
recommended to use "Automatic Search".  
When you perform Automatic Search, the content of the  
current channel list is discarded and a new list is created.  
To search for available channels without discarding the  
content of the current channel list, perform channel  
search from the Digital TV Screen.  
6
KTC-D600E  
Using remote controller  
Favorite Channel List  
Additional channel list  
Move the cursor over area A.  
You can additional and erase for TV/RADIO favorite  
channel list.  
Push [] or [] button to select additional  
channel and then press [ENTER] button.  
1
Show Menu Control Screen by touching  
[Menu] button.  
Erasing channel list  
2
3
Touch [] or [] button to select "Channel".  
Move the cursor over area B.  
Push [] or [] button to select erasing  
channel and then press [ENTER] button.  
Touch [] or [] button to select "Edit  
Channel" and then press [Enter] button.  
Selecting TV/Radio channels  
Setting > Channel  
Push [TV/RADIO] button to select TV /  
RADIO channel.  
Search  
System  
Channel  
Preference  
Selecting the channel from favorite list  
Edit Channel  
Move the cursor to area B.  
Push numeric (1-6) button to select favorite  
list. (Favorite1~6)  
5
Using Direct Touch  
Touch [ ] button when you are finished.  
Using remote controller  
Push [Return] button when you are finished.  
Channel > Edit Channel  
TV  
Favorite 1  
1000. 4Music  
1000. 4Music  
1001. VIVA  
1001. VIVA  
1003. Virgin1+1  
1004. Ideal World  
1005. Dave ja vu  
1003. Virgin1+1  
1004. Ideal World  
1005. Dave ja vu  
B
A
4
Using Direct Touch  
Additional channel list  
Touch [] or [] button to select additional  
channel and then press [ ] button.  
Erasing channel list  
Touch [] or [] button to select erasing  
channel and then press [ ] button.  
Selecting TV/Radio channels  
Touch [ ] button to select tv channel.  
Touch [ ] button to select tv channel.  
Selecting the channel from favorite list  
Touch [] or [] button to select favorite  
list. (Favorite1~6)  
English  
7
Settings  
Restoring to Factory Default  
Updating the Software  
Restore this unit's settings to factory default.  
Download the new software from the USB Memory  
stick and update the software installed in this unit.  
1
Show Menu Control Screen by touching  
[Menu] button.  
1
Show Menu Control Screen by touching  
[Menu] button.  
2
3
Touch [] or [] button to select "System".  
2
3
Touch [] or [] button to select "System".  
Touch [] or [] button to select "Reset  
Default" and then press [Enter] button.  
Touch [] or [] button to select "Software  
Update" and then press [Enter] button.  
Setting > System  
Setting > System  
Search  
System  
Channel  
Preference  
Search  
System  
Channel  
Preference  
System Status  
Reset Default  
System Status  
Reset Default  
Software Update  
Common Interface  
Software Update  
Common Interface  
4
Touch [] or [] button to select "OK" and  
then press [Enter] button.  
4
Touch [] or [] button to select "OK" and  
then press [Enter] button.  
System > Reset Default  
System > Software Update  
Do you want to software update?  
All setting values will be returned to the Initial values.  
Do you want to reset all setting value?  
OK  
OK  
Chancel  
Chancel  
5
Touch [Return] button when you are finished.  
5
The device will be turned off and on  
automatically.  
Software update will start in a moment from  
the LOGO screen.  
The device will be turned off automatically when  
the update is finished.  
Press the RESET button once, then the software  
update process is completed.  
8
KTC-D600E  
Parental Level Setup  
• Do not turn off the power while update is in progress.  
• If the power is turned off accidentally during upgrading,  
turn on the power while keeping the USB stick in the slot.  
The Update menu will then be activated automatically.  
Sets a parental level.  
1
Show Menu Control Screen by touching  
[Menu] button.  
6
Touch [Return] button when you are finished.  
2
3
Touch [] or [] button to select "Preference".  
• This function is only available when the USB Memory stick  
supports this feature.  
• When new software is loaded, this might have different  
functions than the software you are using now. This  
manual might not be accurate anymore for the new  
software version.  
Touch [] or [] button to select "Parental  
Control" and then press [Enter] button.  
Setting > Preference  
Search  
System  
Channel  
Preference  
Parental Control  
Language Setting  
Time Setting  
A/V Control  
4
Press the number ([1] – [0]) button on the  
remote controller to enter password.  
By default, “0000” is specified.  
Parental Control > Password  
1
4
7
2
5
8
0
3
6
9
PASSWORD  
*
*
*
*
5
Touch [] or [] button to select "Setting  
Censorship" and then press [Enter] button.  
Preference > Parental Control  
Setting Censorship  
Change Password  
English  
9
Settings  
Touch [] or [] button to select Parental  
6
Language Setup  
Level and then press [Enter] button.  
Selects a language you use for the Menu, Audio  
and the Subtitle.  
Parental Control > Setting Censorship  
Setting Censorship  
View all  
1
Show Menu Control Screen by touching  
[Menu] button.  
5
7
2
3
Touch [] or [] button to select "Preference".  
12  
15  
Touch [] or [] button to select  
"Language  
Setting and then press [Enter] button.  
"
When you change the password ...  
Setting > Preference  
1
Touch [] or [] button to select  
Change Password and then press  
[Enter] button.  
Search  
System  
Channel  
Preference  
"
"
Parental Control  
Language Setting  
Time Setting  
Preference > Parental Control  
A/V Control  
Setting Censorship  
Change Password  
4
5
6
Touch [] or [] button to select sub item  
and then press [Enter] button.  
Preference > Language Setting  
2
Press the number ([1] – [0])button on  
the remote controller to enter new  
password.  
Menu Language  
Audio Language  
Subtitle Language  
Parental Control > Change Password  
1
4
7
2
5
8
0
3
6
9
New Password  
*
*
*
*
Touch [] or [] button to select Language  
and then press [Enter] button.  
Language Setting > Menu Language  
Menu Language  
English  
Parental Control > Change Password  
German  
Spanish  
Italian  
1
4
7
2
5
8
0
3
6
9
Verify Password  
Dutch  
*
*
*
*
Touch [Return] button when you are finished.  
7
Touch [Return] button when you are finished.  
10  
KTC-D600E  
Time Setup  
AV Setup  
Set the time zone of GMT (Greenwich mean time)  
and summer time as necessary.  
Set the audio and video output mode.  
1
Show Menu Control Screen by touching  
[Menu] button.  
1
Show Menu Control Screen by touching  
[Menu] button.  
2
3
Touch [] or [] button to select "Preference".  
2
3
Touch [] or [] button to select "Preference".  
Touch [] or [] button to select  
"A/V  
Touch [] or [] button to select  
"Time  
Control and then press [Enter] button.  
"
Setting and then press [Enter] button.  
"
Setting > Preference  
Setting > Preference  
Search  
System  
Channel  
Preference  
Search  
System  
Channel  
Preference  
Parental Control  
Language Setting  
Time Setting  
Parental Control  
Language Setting  
Time Setting  
A/V Control  
A/V Control  
4
Touch [] or [] button to select "Audio  
Output" or "Screen Ratio" and then press  
[Enter] button.  
4
5
6
Touch [] or [] button to select "GMT  
Offset and then press [Enter] button.  
"
Preference > Time Setting  
Preference > A/V Control  
GMT Offset  
Audio Output  
Screen Ratio  
Daylight Saving  
Touch [] or [] button to select GMT time  
and then press [Enter] button.  
5
Touch [] or [] button to select Audio  
output and then press [Enter] button.  
Time Setting > GMT Offset  
GMT Offset  
A/V Control > Audio Putput  
Stereo  
Left  
GMT 02:00  
GMT 01:30  
GMT 01:00  
GMT 00:30  
GMT 00:00  
Right  
Touch [Return] button when you are finished.  
English  
11  
Settings  
Touch [] or [] button to select Screen  
6
Time zone list  
ratio and then press [Enter] button.  
Continent  
City  
Time  
Difference  
Continent  
City  
Time  
Difference  
A/V Control > Screen Ratio  
Kansas City  
–6:00  
–5:00  
+7:00  
+8:00  
+3:00  
+2:00  
–8:00  
–5:00  
+0:00  
–8:00  
+1:00  
+11:00  
+8:00  
–6:00  
–11:00  
+2:00  
+3:00  
+3:00  
+11:00  
+5:30  
–6:00  
–5:00  
–3:30  
+6:00  
+13:00  
+1:00  
–5:00  
–5:00  
+1:00  
+1:00  
+6:30  
+1:00  
–8:00  
–4:00  
+1:00  
–8:00  
+8:00  
+3:00  
+1:00  
+10:00  
+8:00  
+3:30  
+9:00  
–5:00  
+1:00  
–8:00  
+1:00  
+1:00  
+1:00  
+1:00  
(GMT)  
Hawaii  
Alaska  
Pacific Time  
–10:00  
–9:00  
–8:00  
–7:00  
–7:00  
–6:00  
–5:00  
–5:00  
–4:00  
–2:00  
+1:00  
+4:00  
+9:30  
+2:00  
+1:00  
–9:00  
+2:00  
+2:00  
–5:00  
+12:00  
+3:00  
+4:00  
+7:00  
+8:00  
+2:00  
+1:00  
–5:00  
–3:00  
+1:00  
+2:00  
+1:00  
–3:00  
+2:00  
–1:00  
–4:30  
–6:00  
+1:00  
–7:00  
–5:00  
+6:00  
+5:00  
+2:00  
+2:00  
+8:00  
+5:00  
+2:00  
+7:00  
+2:00  
+2:00  
+4:30  
Kingston  
Krasnoyarsk  
Kuala Lumpur  
Kuwait  
Kyiv  
Las Vegas  
Lima  
London  
Los Angeles  
Madrid  
Magadan  
Manila  
Mexico City  
Midway Is.  
Minsk  
4:3  
16:9  
Arizona  
Mountain Time  
Central Time  
Eastern time  
Indiana  
Atlantic Time  
Mid-Atlantic  
W.Central Africa  
Abu Dhabi  
Adelaide  
Amman  
Amsterdam  
Anchorage  
Ankara  
Athens  
Atlanta  
Auckland  
Baghdad  
Baku  
Bangkok  
Beijing  
Beirut  
Berlin  
Bogotá  
Brasilia  
Moscow  
Nairobi  
New Caledonia  
New Delhi  
New Orleans  
New York  
Newfoundland  
Novosibirsk  
Nuku’alofa  
Oslo  
Ottawa  
Panama  
Paris  
Prague  
Yangon  
Brussels  
Bucharest  
Budapest  
Buenos Aires  
Cairo  
Cape Verde Is.  
Caracas  
Chicago  
Copenhagen  
Denver  
Detroit  
Dhaka  
Ekaterinburg  
Harare  
Helsinki  
Rome  
San Francisco  
Santiago  
Sarajevo  
Seattle  
Singapore  
St. Petersburg  
Stockholm  
Sydney  
Taipei  
Tehran  
Tokyo  
Toronto  
Tunis  
Vancouver  
Vienna  
Warsaw  
Zagreb  
Zurich  
Hong Kong  
Islamabad  
Istanbul  
Jakarta  
Jerusalem  
Johannesburg  
Kabul  
12  
KTC-D600E  
Displaying EPG  
Receiving and displaying EPG (Electronic Program  
Guide) sent together with a program.  
Viewing the Program Guide  
You can check the programs on each channel in the  
EPG (Electronic Program Guide).  
1
2
Show Menu Control Screen by touching  
[EPG] button.  
Select the channel or time to display  
EPG  
1000. RTL Television  
09:30 ~ 10:00 Die Kinderrzte von St. Marien  
10:00 ~ 10:30 Unsere erste gemeinsame Woh...  
10:30 ~ 11:00 Mein Garten  
11:00 ~ 12:00 Punkt 12 - Das RTL-Mittagsjou...  
12:00 ~ 13:00 Die Oliver Geissen Show  
On the EPG, you can change the displayed  
channel by touching [] or [] button.  
(Press [] or [] button when using the remote  
controller.)  
Time frame by touching [] or [] button.  
( Press [] or [] button when using the remote  
controller.)  
3
Select the channel or time to display  
Detail EPG  
Die Kinderrzte von St. Marien  
Folge 20  
Die Doku rund um das Kinderkrankenhaus St.  
Marien  
Press [ENTER] after highlighting the program  
to watch, then the detailed information will be  
displayed as shown above.  
4
Touch [Return] button when you are finished.  
• A "no data" message will be displayed if the selected  
channel does not provide EPG data.  
• It can also be displayed from the Menu Control screen.  
English  
13  
Operation of Remote Control Unit  
PWR  
/  
To turn on and off this unit.  
Toggles between menu items (up/down).  
INFO  
/
To show the carrier information of the currently  
selected station (toggle between pages in menu  
Toggles between menu items (left/right).  
ENTER  
Verifies input.  
using  
//  
/
).  
EPG  
RTN  
Opens the Electronic Program Guide.  
a. Return to the previous menu in menu screen or  
escape from menu.  
CH LIST  
Opens the channels list.  
b. Return to normal TV mode from a menu.  
Repeated pressing will take you through  
all opened menus until normal TV mode is  
reached.  
CH  
/  
Changes channels (channel up, channel down).  
c. Returns to the channel you were watching  
previously.  
MENU  
Press once to enter Setting Menu.  
The Setting Menu consists of 4 main-menus.  
Search  
LANG  
Switches Menu language.  
System  
Channel  
Preference  
SUBTITLE  
Switches to Subtitle language.  
14  
KTC-D600E  
AUDIO  
Switches to Audio language.  
Preparing the Remote Control Unit  
Pull the battery sheet out from  
the remote control unit to the  
direction of the arrow.  
TELETEXT  
Switches to teletext.  
VOL /  
To adjust volume. Volume mute only works in TV/  
Radio mode.  
MUTE  
Mutes the sound. Volume mute only works in TV/  
Radio mode.  
Changing the battery of the remote  
control unit  
Use a commercially available button battery (CR2025).  
Insert the battery with the + and – poles aligned  
properly, following the illustration inside the case.  
0 – 9  
a. Selects a favorit list.  
b. Selects a sub-menu item.  
c. Selects a teletext.  
Keep on slide  
SEEK  
Searches the network for available channels.  
Short - Manual Search  
long - Automatic Search  
Pull out  
CR2025  
(+side)  
TV/RADIO  
TV/radio mode  
CAUTION  
• Do not set the remote control in hot places such as on the  
dashboard.  
• Lithium battery.  
Danger of explosion if the battery is incorrectly replaced.  
Replace only with the same or equivalent type.  
The battery pack or batteries shall not be exposed to  
excessive heat such sunshine, fire or the like.  
• Keep battery out of reach of children and in original  
package until ready to use. Dispose of used batteries  
promptly. If swallowed contact physician immediately.  
English  
15  
Accessories  
Installation  
Installing the Main Unit  
The Digital TV Tuner (main unit) can be installed  
by securing it to the pile carpet with Velcro or by  
screwing it on to a commercially available audio  
board.  
Wiring harness (6m)........................... 1  
Remote Control Sensor (6m)........ 1  
TV Interface Cable (6m) ................... 1  
Bracket........................................................ 2  
Screw (M2.6 × 5mm)......................... 4  
Screw (φ4 × 16mm)........................... 4  
• There are various terminals on the main unit. Leave some  
space to connect cables on the terminal side of the main  
unit.  
• Do not place anything on top of the main unit. This can  
cause product failure.  
• Do not install the main unit stacked with other units.  
• Install the main unit at least 1.5m away from radio  
antenna.  
Installing with Screw  
1 Use a tapping screw to secure the bracket to the  
vehicle's audio board (commercial product).  
• When drilling holes in the vehicle, be sure there is nothing  
on the other side.  
Damage to cables or pipes can cause accident or  
malfunction.  
Screw (φ4×16mm)  
Screw (M2.6×5mm)   
Bracket   
Screw  
(M2.6×5mm)   
Bracket   
Audio board  
(commercial product)  
Digital TV Tuner  
Remote Control Unit ........................ 1  
16  
KTC-D600E  
Installing the Remote Control Sensor  
Inserting CA Card and CAM  
Paste the remote control sensor to the dashboard.  
Insert the CA card (Conditional Access card) and CAM  
(Conditional Access Module) into the card slot.  
1 Remove the paper from double-stick tape and paste  
it on the back of the remote control sensor.  
2 Wipe the dirt and oil off from the installation area  
and paste the remote control sensor to the  
dashboard.  
Remote control sensor   
• CA card (Conditional Access card) and CAM (Conditional  
Access Module) is optional (sold separately).  
• When CA card and CAM are inserted in this unit, CA card  
and CAM protrude from a unit. Take well care about an  
installation position.  
When you insert or draw out a CA card and CAM in the  
slot of this unit, be sure to ACC OFF.  
• When you insert or draw out a CA card and CAM, keep it  
horizontally.  
• Eject or insert the CA card or CA module before turning  
on the power.  
• Do not leave this device inside the car. The temperature  
inside the car may rise rapidly, and CA card or other parts  
may be deformed or become unusable due to the heat  
inside the car.  
• Wipe oil and dirt off from the installation surface.  
• Avoid area where there is direct sunlight or close to TV  
monitor because the remote control signals may be  
affected.  
There is also the danger of theft.  
English  
17  
Connection  
Remoto control sensor   
Digital TV Tuner  
Ignition wire (Red)  
Fuse (1A)  
It is used for updating the software.  
Battery wire (Yellow)  
Fuse (5A)  
Ground wire (Black)  
(To car chassis)  
Wiring harness   
• 75Ω/ F connector  
• For VHF/UHF  
Up to 2 antennas can be  
connected to the antenna  
sockets “ANT A” and “ANT B.  
Set "Active Antenna DC" is  
"Enable" (DC5V ON) when active  
antenna is used.  
TV Interface Cable   
To the Monitor unit such as a  
DVD receiver.  
AV Cable (Commercially available)  
To AV input of the monitor  
VIDEO: Yellow  
AUDIO (L): White  
AUDIO (R): Red  
Ignition key switch  
ACC A  
B
Car fuse box  
(Main fuse)  
Car fuse box  
C
GND  
Battery  
18  
KTC-D600E  
LZ-612IR Operation  
LZ-612IR Setup1  
LZ-612IR Setup2  
1
Enter Select screen mode  
Touch the display window.  
1
Enter Select screen mode  
Touch the display window.  
2
Select the function  
2
Select the function  
Touch the function button.  
Touch the function button.  
PAGE  
PWR  
MUTE  
VOL  
MENU  
AVIN  
INFO  
CH  
PAGE  
TV.M  
TV/R  
EPG  
CH.L  
SEEK  
VOL  
CH  
RTN  
ENT  
RTN  
ENT  
Display  
PAGE  
MENU  
PWR  
Function  
Display  
PAGE  
EPG  
TV.M  
CH.L  
Function  
Move to the DVB-T Tuner unit Setup Screen 2.  
Move to Monitor Setting screen .  
To turn on and off this unit.  
Move to the DVB-T Tuner unit Setup Screen 1.  
Opens the Electronic Program Guide.  
Press once to enter TV Setting Menu.  
Opens the channels list.  
AVIN  
Change AV1 / AV2 input source.  
MUTE  
Mutes the sound.  
TV/R  
SEEK  
TV/radio mode.  
Searches the network for available channels.  
Short - Manual Search  
long - Automatic Search  
Toggles between menu items (up/down).  
Toggles between menu items (left/right).  
a. Return to the previous menu in menu screen or  
escape from menu.  
Volume mute only works in TV/Radio mode.  
INFO  
To show the carrier information of the currently  
selected station (toggle between pages in menu  
using  
///).  
/
/
VOL  
/VOL  
To adjust volume. Volume mute only works in TV/  
Radio mode.  
Changes channels (channel up, channel down).  
RTN  
CH  
/CH  
b. Return to normal TV mode from a menu.  
Repeated pressing will take you through all opened  
menus until normal TV mode is reached.  
c. Returns to the channel you were watching previously.  
RTN  
a. Return to the previous menu in menu screen or  
escape from menu.  
b. Return to normal TV mode from a menu.  
Repeated pressing will take you through all opened  
menus until normal TV mode is reached.  
c. Returns to the channel you were watching previously.  
ENT  
Verifies input.  
ENT  
Verifies input.  
3
Exit DVB-T Tuner unit Control mode  
Touch the screen except function button.  
3
Exit DVB-T Tuner unit Control mode  
Touch the screen except function button.  
• The relevant OSD is displayed only when the DVB-T  
Control in <Other Setting> (page 7 In LZ-612IR Manual) is  
turned on.  
• You can operate the Kenwood DVB-T Tuner unit  
connected to the Hideaway box when the DVB-T Control  
is turned on.  
• The relevant OSD is displayed only when the DVB-T  
Control in <Other Setting> (page 7 In LZ-612IR Manual) is  
turned on.  
• You can operate the Kenwood DVB-T Tuner unit  
connected to the Hideaway box when the DVB-T Control  
is turned on.  
English  
19  
LZ-612IR Connection  
Specifications  
System Connection with LZ-612IR  
LZ-612IR Hideway Unit  
TV tuner  
Input Frequency  
VHF : 174 – 230 MHz  
UHF : 470 – 862 MHz  
Demodulation Type  
: QPSK/ 64QAM/ 16QAM  
Channel Bandwidth  
: 7/ 8 MHz  
FFT Size  
: 2K and 8K  
Remote Control Cable  
KTC-D600E  
Guard Interval  
: 1/4, 1/8, 1/16, 1/32  
Puncture Rate  
: 1/2, 2/3, 3/4, 5/6, 7/8  
Antenna input  
: 2-ch Diversity  
Connector Type  
: F Type × 2  
General  
Operating Voltage (10.5-16V)  
• Connect the audio/video output of KTC-D600E to “AV2  
INPUT” of LZ-612IR.  
• Use the remote control cable of LZ-612IR to connect the  
remote input terminal of KTC-D600E and “DVD Remote  
Out” terminal of LZ-612IR.  
: 14.4 V  
Current Consumption  
: 400 mA  
Dimensions (W × D × H) (Main unit)  
: 188 × 144 × 30 mm  
Operational temperature range  
: -10°C ~ +60 °C  
Storage temperature range  
: -30°C ~ +85 °C  
Weight  
: 0.9 kg  
Specifications subject to change without notice.  
20  
KTC-D600E  
Declaration of Conformity with regard to  
the EMC Directive 2004/108/EC  
Manufacturer:  
Kenwood Corporation  
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525  
Japan  
EU Representative’s:  
Kenwood Electronics Europe BV  
Amsterdamseweg 37, 1422 AC UITHOORN, The  
Netherlands  
This Product is not installed by the manufacturer of a  
vehicle on the production line, nor by the professional  
importer of a vehicle into an EU Member State.  
Information on Disposal of Old Electrical  
and Electronic Equipment and Batteries  
(applicable for EU countries that have  
adopted separate waste collection systems)  
Products and batteries with the symbol  
(crossed-out wheeled bin) cannot be  
disposed as household waste.  
Old electrical and electronic equipment and  
batteries should be recycled at a facility  
capable of handling these items and their  
waste byproducts.  
Contact your local authority for details in  
locating a recycle facility nearest to you.  
Proper recycling and waste disposal will help  
conserve resources whilst preventing  
detrimental effects on our health and the  
environment.  
Notice: The sign “Pb” below the symbol for  
batteries indicates that this battery  
contains lead.  
For Turkey  
Bu ürün 26891sayılı Resmi Gazete’de yayımlanan  
Elektrikli ve Elektronik Eşyalarda Bazı Zararlı Maddelerin  
Kullanımının Sınırlandırılmasına Dair Yönetmeliğe  
uygun olarak üretilmiştir.  
This symbol mark indicates that  
Kenwood manufactured this product  
so as to decrease harmful influence on  
the environment.  
This product complies with Directive,Number 26891  
regarding "REGULATION ON THE RESTRICTION OF  
THE USE OF CERTAIN HAZARDOUS SUBSTANCES IN  
ELECTRICAL AND ELECTRONIC EQUIPMENT".  
DVB is a registered trademark of the DVB Project.  
English  
21  

Sharp Mx M623 User Manual
Samsung Aw1093m User Manual
LG LDE3015ST User Manual
LG AS10GD User Manual
Lexmark X864dhe User Manual
CRAFTSMAN 486.24443 User Manual
CRAFTSMAN 390.291198 User Manual
CRAFTSMAN 315.228110 User Manual
BLAUPUNKT GTX 1662 CHN User Manual
ASUS VK228T User Manual