KENWOOD KPG 46X User Manual

USB PROGRAMMING INTERFACE CABLE  
KPG-36X KPG-46X  
INSTRUCTION MANUAL  
ABOUT SELECTING USB/ UART (VIRTUAL COM PORT)  
SUPPLIED ITEMS  
For using USB (Up to 12 Mb/s USB Speed), Slide the SW of KPG-36X/  
USB programming interface cable (USB 2.0 Full speed (12 Mb/s)  
compliant) <cable length: 4.92 ft/ 1.5 m>  
46X to "USB".  
For using UART (Virtual COM Port), Slide the SW of KPG-36X/ 46X to  
"UART".  
CD (with driver software)  
Instruction manual (B5A-0568-XX)  
CONFIRMING THE INSTALLATION  
Connect the KPG-36X/ 46X to a USB port, In the “Device Manager”, open  
the “Ports (COM & LPT)”.  
In case of the SW position of UART, If “Silicon Labs CP210x USB to  
UART Bridge(COMx)” appears, installation is complete.  
In case of the SW position of the USB, “KENWOOD Type1(COMx)”  
appears, installation is complete.  
OPERATING SYSTEM  
Windows 7, Windows 8.1, or Windows 10 operating system.  
(Use in desktop mode is recommended. The driver installation software  
does not support touch input.)  
INSTALLING THE DRIVER  
When using the KPG-36X/ 46X for the first time, install the supplied  
KPG-36X/ 46X driver.  
COPYRIGHTS  
ATTENTION:  
Windows® is a registered trademark of Microsoft Corporation in the  
United States and/or other countries.  
Applicable operating systems are subject to change without notice  
due to the end of the technical support by Microsoft Corporation or  
change of the product specifications.  
For Fpro software, use version 6.30 or later.  
For KFL software, use version 1.22 or later.  
Depending on the usage condition of the USB apparatus, saved  
content may be lost. JVC KENWOOD Corporation does not take  
responsibility for damages or lost content.  
Other product and company names mentioned herein may be the  
trademarks of their respective owners.  
One or more of the following statements may be applicable to this  
equipment.  
FCC WARNING  
This equipment generates or uses radio frequency energy. Changes or  
modifications to this equipment may cause harmful interference unless the  
modifications are expressly approved by the party responsible/  
JVC KENWOOD. The user could lose the authority to operate this equipment  
if an unauthorized change or modification is made.  
1
2
Turn on the PC, then insert the supplied CD into the CD-ROM drive  
of the PC.  
When using KPG-36X/ 46X for NX-5000 series and NX-3000 series,  
the USB driver whose transfer rate is faster than the UART (Virtual  
COM Port) driver or the current UART (Virtual COM Port) driver can  
be selected.  
Refer to the service manual for other models, and if there are not  
any specific descriptions, select the UART (Virtual COM Port)  
driver.  
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY  
THE FCC  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference  
in a residential installation.  
If installing the UART (Virtual COM Port) driver:  
Double-click “CP210x_VCP_Windows” folder .  
Double-click “CP210xVCPInstaller_x64.exe” or  
CP210xVCPInstaller_x86.exe” file. When the installation Wizard  
starts, click [Next>].  
This equipment generates, uses and can generate radio frequency energy  
and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, there is  
no guarantee that the interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by one or more of the  
following measures:  
If installing the USB driver:  
Double click Kenwood_Type_1_USB_Driver” folder. Double  
click “Kenwood_Type_1_USB_Driver_32bit.bat” or Kenwood_  
Type_1_USB_Driver_64bit.bat” file. When the Installation Wizard  
starts, click [Next>].  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment to an outlet on a circuit different from that to which  
the receiver is connected.  
Concerning the 64-bit version or 32-bit version, you should  
check the PC in advance.  
3
4
Read through the licensing agreement. If you consent to the terms of the  
agreement, check the "I accept this agreement", then click [Next>].  
Consult the dealer for technical assistance.  
Start the installation.  
Information on Disposal of Old Electrical and Electronic Equipment and  
Batteries (applicable for countries that have adopted separate waste  
collection systems)  
When the driver finishes copying to the PC, click [Finish].  
Note:  
Products and batteries with the symbol (crossed-out wheeled bin) cannot  
be disposed as household waste.  
Old electrical and electronic equipment and batteries should be recycled  
at a facility capable of handling these items and their waste byproducts.  
Contact your local authority for details in locating a recycle facility nearest  
to you.  
The KPG-36X/ 46X is installed as a virtual com port.  
The KPG-36X/ 46X does not support programs other than those  
used for KENWOOD transceivers.  
If the driver cannot be installed or if, having installed the driver and  
restarted your PC, the driver cannot be found or the operation does  
not stabilize, try changing the USB port to that which you have  
connected the KPG-36X/ 46X. Additionally, try removing other  
equipment attached to the USB ports of the PC.  
Proper recycling and waste disposal will help conserve resources whilst  
preventing detrimental effects on our health and the environment.  
Access the following URL for the drivers download information:  
CONNECTING TO A PC AND TRANSCEIVER  
Connect the KPG-36X/ 46X USB connector to the USB port of the PC,  
and the other connector to the transceiver.  
Note:  
Connect the KPG-36X/ 46X directly to the transceiver and the PC  
(or USB HUB).  
Do not connect the KPG-36X/ 46X other than PC (or USB HUB).  
It causes malfunction of the KPG-36X/ 46X and the transceiver.  
B5A-0568-10 (M)  
© 2018  

Soleus Air Air Conditioner Sg Ttw 14hc User Manual
Schumacher 85 716 User Manual
Samsung Us09s8gb User Manual
Philips Scb3021 User Manual
LG 65UH7700 02 User Manual
HP 8512A User Manual
FUJITSU RC25 User Manual
CRAFTSMAN 917.292480 User Manual
CANON SURE SHOT 150U DATE User Manual
BLACK DECKER CHV1410 User Manual