JOHN DEERE
WORLDWIDE COMMERCIAL & CONSUMER
EQUIPMENT DIVISION
M155003
J5
Broadcast Spreader
LPBST-35JD
OMM155003 J5
OMM155003 J5
OPERATOR’S MANUAL
All information, illustrations and
specifications in this manual are based on
the latest information at the time of
publication. The right is reserved to make
changes at any time without notice.
COPYRIGHT© 2005
Deere & Co.
John Deere Worldwide Commercial and
Consumer Equipment Division
All rights reserved
Previous Editions
COPYRIGHT© 2004
North American Version
Litho in U.S.A.
SAFETY
in an unsafe manner.
Keep riders off of hitch bracket.
Safety
Keep Feet From Under Drawbar
Before you disconnect an attachment from machine hitch plate:
• Unload attachment.
Read the general safety operating precautions in your machine operator’s
manual for additional safety information.
Operate Safely
• Stop attachment on level ground.
• Stop machine engine.
• This attachment is intended for use in lawn care and home applications.
Do not tow behind a vehicle on a highway or in any high speed application.
Do not tow at speeds higher than maximum recommended towing speed.
• Lock machine park brake.
• Block attachment wheels.
• Towing speed should always be slow enough to maintain control. Travel
slowly over rough ground.
• Make sure feet are not under drawbar.
• Do not let children or an untrained person operate machine.
• Do not let anyone, especially children, ride on machine or attachment.
Riders are subject to injury such as being struck by foreign objects and
being thrown off. Riders may also obstruct the operator’s view, resulting in
the machine being operated in an unsafe manner.
Assembly
Parts in Kit
• Check machine brake action before you operate. Adjust or service
brakes as necessary.
• Keep all parts in good condition and properly installed. Fix damage
immediately. Replace worn or broken parts. Replace all worn or damaged
safety and instruction decals.
• Do not modify machine or safety devices. Unauthorized modifications to
the machine or attachment may impair its function and safety.
B
• Securely anchor all loads to prevent loads from falling.
Towing Loads Safely
• Stopping distance increases with speed and weight of towed load. Travel
slowly and allow extra time and distance to stop.
• Total towed weight must not exceed limits specified in towing vehicle
operator’s manual.
A
• Excessive towed load can cause loss of traction and loss of control on
slopes. Reduce towed weight when operating on slopes.
• Never allow children or others in or on towed equipment.
C
• Use only approved hitches. Tow only with a machine that has a hitch
designed for towing. Do not attach towed equipment except at the
approved hitch point.
F
G
• Follow the manufacturer’s recommendations for weight limits for towed
equipment and towing on slopes. Use counterweights or wheel weights as
described in the machine operator’s manual.
D
• Do not turn sharply. Use additional caution when turning or operating
under adverse surface conditions. Use care when reversing.
D
• Do not shift to neutral and coast downhill.
Protect Bystanders
• Keep bystanders away when you operate a towed attachment.
• Before you back machine and attachment, look carefully behind
attachment for bystanders.
E
MX34594
Keep Riders Off Towed Attachment
Qty.
1
Description
Keep riders off of a towed attachment.
Riders on a towed attachment are subject to injury, such as being struck
by objects and being thrown off the attachment during sudden starts,
stops and turns.
Fan (A)
1
Hopper Assembly and Control Support (B)
Riders obstruct the operator's view, resulting in the attachment being used
Safety - 2
ASSEMBLY
Assemble Hopper and Transmission to Frame
Qty.
1
Description
A
Tube, Tow (C)
Wheel (D)
2
B
1
Axle (E)
1
Support Frame, Hopper (F)
Transmission (G)
1
Bag of Parts - Hardware (Small Bag)
C
Qty.
4
Description
Locknut, 5/16 in.
2
Nut, 5/16 in.
2
Bolt, Hex, 5/16 x 3 in.
Carriage Bolt, 5/16 x 2 in.
Hitch Pin, 1/2 x 2-1/2 in.
Spring Locking Pin, 1/8 in. (Small)
Washer, Flat, 5/8 in.
2
D
1
1
6
E
2
Spring Locking Pin (Open)
Spring Locking Pin (Closed)
Locknut, 1/4 in.
1
6
6
Bolt, Hex, Stainless, 1/4 x 1-3/4 in.
Cotter Pin, 1/8 x 1 in.
MX34596
1
1. Install six 1/4 x 1-3/4 in. hex bolts (A), and 1/4 in. thrust washer (B)
through top of hopper (C) and through support frame (D), as shown.
Secure bottom of bolt with 1/4 in. locknut (E). To avoid damage to plastic,
do not overtighten hardware.
Bag of Parts - Hardware (Large Bag)
Qty.
2
Description
Clevis, Hitch
2
Bearing, Axle
G
H
2
Snap Ring, E-Type
Washer, Thrust, 1/4 in.
O-Ring, 3/8 in. ID
Spring, Agitator (Stainless)
Lock Clip
F
I
J
6
1
1
1
1
Driver, Fan
MX34597
2. Install lock clip (F) and fan driver (G), with small diameter lip of driver
toward the bottom, as shown.
3. Slide fan (H) onto transmission assembly (I) shaft over top of fan driver.
Move lock clip, fan driver, and fan downward so top of fan is approximately
12.7 cm (5 in.) (J) from top of transmission shaft.
Assembly - 3
ASSEMBLY
Install Axle and Wheels
IMPORTANT: Avoid damage! Use only one spring locking pin
(open) to engage the wheels. The extra pin is included only when
using the unit on ice for extra traction.
Use of two pins on dry pavement may result in damage to the
unit.
5. Install spring locking pin (open) (L) through inside hole in wheel rim and
axle onto either side of axle.
C
B
Install Agitator and Controls
A
NOTE: The four tabs on the fan should be compressed against the
fan driver. If pressure is not applied, the fan connection will be loose
resulting in poor performance.
MX34598
1. Install axle (A) through support frame assembly (B) with raised bump
(C) on transmission toward front of spreader assembly, and offset hole in
axle installed toward left side of spreader.
D
B
C
A
F
D
D
E
MX34599
MX34601
Picture Note: View from rear of spreader.
1. Adjust fan (A) upwards with fan driver (B) and lock clip (C) on shaft as
close to bottom of hopper (D) without touching during operation. Make
sure fan driver engages the four plastic tabs on the bottom of fan.
2. Slide axle until lengths (D) are equal, and install spring locking pin
(closed) (E) into left side hole (F).
I
J
H
H
I
F
B
E
G
K
K
L
I
G
H
J
MX34600
3. Install axle bearing (G) onto each side of axle so square end of bearing
fits into square hole of support frame assembly (B).
NOTE: Add or delete washers (H) to reduce axle side to side
movement.
MX34602
2. Install 3/8 in. ID O-ring (E) on transmission shaft (F) until seated on
bottom of hopper (G).
4. Install two 5/8 in. flat washers (H) onto each side of axle. Install wheel
(I), 5/8 in. flat washer (J), and snap ring (K) onto end of axle.
3. Install agitator (H), and secure with 1/8 x 1 in. cotter pin (I) through top
loop in agitator and hole in transmission shaft, as shown.
Assembly - 4
INSTALLING
M
S
P
Q
J
K
J
R
L
T
MX34605
MX34603
6. Install hitch clevis brackets (P) onto tow tube end (J) with two 5/16 x 2
in. carriage bolts (Q) and 5/16 in. locknuts (R), as shown. Tighten
hardware.
4. Install tow tube (J) onto support frame (K) with two 5/16x3 in. hex bolts
(L) and 5/16 in. hex nuts (M). Tighten hardware and torque bolts to 30 N•m
(22 lb-ft), or one complete turn after finger tight.
7. Install 1/2 x 2-1/2 in. hitch pin (S) and 1/8 in. spring locking pin (small)
(T) through end of clevis brackets, as shown.
O
Installing
L
Installing
N
1. Park machine safely. See “Parking Safely” in Safety section.
B
C
A
MX34595
2. Remove 1/8 in. spring locking pin (A) and 1/2 x 2-1/2 in. hitch pin (B)
from hitch clevis (C) of spreader or other storage location.
3. Pull spreader forward and position hitch clevis to straddle machine rear
hitch plate or drawbar (not shown). Align all hitch pin holes, then install
hitch pin down through hitch clevis and machine hitch, securing with 1/8
in. spring locking pin (small).
MX34604
5. Install control support tube (N) onto hex bolts (L) tow tube with 5/16 in.
locknuts (O). Tighten hardware.
Installing - 5
REMOVING
Removing
Removing
1. Park machine safely. See “Parking Safely” in the Safety section.
2. Remove all materials from the hopper before removing spreader from
machine.
c
CAUTION: Avoid injury! Keep feet away from under drawbar.
3. Remove 1/8 in. spring locking pin from hitch pin.
4. Hold spreader tow tube to remove pressure from hitch pin, then remove
hitch pin from hitch clevis and rear hitch plate or drawbar on machine.
5. Pull or push spreader backward to disengage hitch clevis from machine
hitch, install hitch pin in hitch clevis for storage and secure with 1/8 in.
spring locking pin.
Storing
The spreader can be tipped upright and stored against a wall using less
space:
1. Remove any loose material from hopper and fan using a brush and
garden hose. The spreader should be clean and dry before storing.
2. Roll spreader to desired storage area, lift hitch clevis to pivot spreader
to vertical position.
Removing - 6
OPERATING
described by the label above. If the material is coming out right or left
during operation, adjustment of this lever should be made to center the
material distribution pattern behind the vehicle. Your broadcast spreader
has a patented feature to allow you to adjust for centering.
Operating
Daily Operating Checklist
One Side Only Spreading
❏
❏
❏
❏
Check for loose or missing hardware.
Make sure all connections are tight.
Make sure attachment responds properly to controls.
Check for debris build-up that could obstruct proper motion of the
spreader control components.
B
Operating the Spreader
The Fan speed and the spread width are controlled by the speed of the
vehicle. The recommended operating speed is slightly faster than that of a
brisk walk, 3 mph. 3 mph is equal to the vehicle traveling 40 ft in nine
seconds.
The flow control assembly operates the flow control plate. The flow control
assembly is marked 0 (closest) to 10 (fully open). The position selected
determine the amount of material to be broadcast. The higher the number,
the heavier the application of material.
Flow control setting for many of the common fertilizers, insecticides, and
grass seeds are provided in the alphabetized table listing flow control
settings. If the product is not listed in the flow control settings table, use
the calibration guide to set the flow control.
The agitator spring located inside the hopper provides consistent material
flow of palletized materials and seed. It is not designed to break up lumps
of material or seed. Break up any lumps as you fill the hopper.
MX34607
The directional control handle can be used for adjusting the material
spread pattern when spreading near sidewalks, planting beds, etc. With
the handle adjusted to the left side (B), the directional control handle only
operates with 90% shut-off of material to the right side of the vehicle as
shown in the illustration above.
After determining the correct setting number for your material, move flow
control lock to that position. Move flow control handle to the lock position
to open the flow control plate.
Directional Control Settings
Operational Tips
Normal Operation (Uniform Spreading)
• Always operate your spreader with the speed limit for which it was
designed - 3 mph.
Fertilizers, insecticides, and grass seed each have different particle size
and weight. This can be referred to as particle density. As the particles are
impacted by the fan, the distribution can be centered or slightly off center
depending on particle density and forward vehicle speed.
• When backing, carefully back straight to avoid jack knifing, which could
result in damage to equipment.
• Only tow your spreader behind vehicles for which it was designed -
riders, and lawn and garden tractors.
• Do not load the hopper with more than the maximum weight capacity of
79 kg (175 lb).
A
• When spreading ice melters, use two spring locking pins, one in each
wheel hub, for better traction.
• When spreading seed, fertilizer, etc., insert only one spring locking pin in
either the right or left wheel hub.
• Break up any lumps as you fill the hopper.
• Do not use on windy days, especially when spreading fine grass seed or
herbicides.
• Optimum hitch height is 18 - 23 cm (7- 9 in.).
Service
Maintenance Tips
MX34606
• The key to years of trouble-free service is to keep your spreader clean
and dry.
Adjustment can be made by moving the direction control handle to the
right or left. The directional decal located below the directional control
plate handle will aid you in adjusting the spread pattern. For most
applications the handle should be placed close to the center position (A)
• Never allow material to remain in hopper for extended periods of time.
• Should rust develop, sand lightly and then paint area with enamel.
Operating - 7
SERVICE
• Periodically check all fasteners for tightness.
• Rinse/dry inside and outside of spreader after each use. Move flow
control as you rinse, to avoid build up of material.
Q
Annual Maintenance
P
O
R
S
C
A
D
B
N
MX34608
M
1. Remove snap ring (A), 5/8 in. flat washer (B), wheels (C) and bearings
(D).
MX34610
7. Remove three screws (M) that secures control plate assembly (N).
2. Clean parts.
8. Remove 1/4 x 2-1/2 in. bolt (O), 1/4 in. flat washer (P), 1/4 in. lock
washer (Q), and 1/4 in. nut (R) and flow control assembly (N) from support
tube (S).
3. Lightly lubricate bearings.
H
I
J
F
G
L
K
MX34611
E
9. Separate parts as shown.
10. Clean thoroughly using soap and water.
11. Assemble parts reverse order of removal.
MX34609
4. Remove spring locking pin (E), and slide axle (F) out from support
frame (G).
Calibration
5. Remove 1/8 x 1 in. cotter pin (H), agitator (I), and 3/8 in. ID O-ring (J),
and transmission (K).
1. Move the flow control assembly lever to OFF setting.
2. If parts are disassembled, assemble all parts.
6. Clean fan (L).
Service - 8
TROUBLESHOOTING
IF
CHECK
Fan does not turn
when pulling.
Find or replace missing spring locking pin in
wheel or transmission..
Check position of fan, fan driver, and lock clip.
A
Specifications
LPBST-35JD Broadcast Spreader
Dimensions
Size (maximum weight). . . . . . . . . . . . . . . . . . . . . . . . . . . 79 kg (175 lb)
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.10 cu m (3.5 cu ft)
Wheels and Tires . . . . . . . . . . . . . 33.0 x 10.2 cm (13 x 5 in) Turf tread
Tire Inflation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 kPa (20 PSI)
B
D
(Specifications and design subject to change without notice.)
E
Flow Control Settings for Specific Products
c
CAUTION: Avoid injury! Chemicals can be dangerous.
Avoid injury to operator or bystanders:
C
• Read chemical container label for mixing and handling
instructions. A Material Safety Data Sheet (MSDS) should be
supplied by the chemical dealer and provides proper safety
information.
MX34612
Picture Note: View from top and rear of spreader.
3. Move the flow control assembly lever to “10” setting (A).
• Wear proper clothing and safety equipment while handling or
applying spray chemicals.
4. Adjust the two nuts (B) on directional control plate (C) in or out
(together) so the flow control plate (D) is fully open (E). Tighten nuts
together.
• Wear a full covering of clothing, protective goggles and
rubber gloves.
5. Move flow control assembly back and forth and to the OFF setting. Flow
control plate will move freely and be in closed position.
• Prohibit all smoking, drinking, and eating around chemicals.
The following is a list of flow control settings for specific products available
for use with the spreader. Some products may not be available in all areas.
Troubleshooting
Flow control settings are based on 3 mph forward speed.
Using Troubleshooting Chart
If you are experiencing a problem that is not listed in this chart, see your
authorized dealer for service.
b
lbs/1000 Flow
Materials
square
feet
Control
Setting
at 3
When you have checked all the possible causes listed and you are still
experiencing the problem, see your authorized dealer.
a
mph
Troubleshooting Chart
10
3.8
2.9
3
6
All American All Purpose Fertilizer 10-10-10
Bayer Season Long Grub Control
Bayer Season Long Grub Control
Bayer Complete Insect Killer
5
IF
CHECK
4
Flow control lever
does not snap into
flow control pointer.
Tighten 1/4 x 2-1/2 in. hex bolt on flow control
lever assembly.
3.5
3
2
Bayer Complete Insect Killer
Not enough or too
much fertilizer
dispensed.
Calibrate the plates.
3
2.5
2
Bayer Power Force Multi-Insect Killer
Bayer Power Force Multi-Insect Killer
Bayer Grub Control
2
Flow control lever
hard or will not
operate.
Loosen 1/4 x 2-1/2 in. hex bolt on flow control
lever assembly.
3
3
2
2.5
3.5
Bayer Grub Control
Take control plates apart, and clean plates out
with water.
3.2
Bayer Lawn Fertilizer Plus Weed Control II 30-3-4
Troubleshooting - 9
SPECIFICATIONS
b
b
lbs/1000 Flow
Materials
lbs/1000 Flow
Materials
square
feet
Control
square
feet
Control
Setting
at 3
Setting
at 3
a
a
mph
mph
3.8
2.9
3.6
3.2
3.5
3
Bayer Season Long Grub Control
Bayer Season Long Grub Control
Bayer Lawn Starter Fertilizer 20-27-5
10
6
Parkers Super Soilife Lawn and Garden Fertilizer
10-10-10
6.5
4.5
Parkers Super Soilife Lawn and Garden Fertilizer
16-4-8
3.5
3.5
Bayer Lawn Fertilizer Plus Crabgrass Preventer
30-3-4
3.6
10
3.5
7
Pennington Lawn Starter Fertilizer 18-24-6
Pennington Master Turf High Traffic Lawn Seed
Mixture
3
3.5
3
Eliminator Ant, Flea, and Tick Killer Granules
Eliminator Ant, Flea, and Tick Killer Granules
Eliminator Ant, Flea, and Tick Killer Granules
Eliminator 5% Diazinon Killer Granules
Howard Johnsons All-Purpose Fertilizer 8-8-8
Howard Johnsons All-Purpose Fertilizer 10-10-10
Howard Johnsons All-Purpose Fertilizer 12-12-12
Ironite 1-0-0
2.5
2
5
5.5
Pennington Master Turf High Traffic Lawn Seed
Mixture
3
8
7
Pennington Master Turf Shady Lawn Seed Mixture
Pennington Master Turf Shady Lawn Seed Mixture
2
3.5
5
4
5.5
7
7
10
Pennington Master Turf Sun and Shade Lawn
Seed Mixture
7
5
7
5
5
5.5
2.5
3
Pennington Master Turf Sun and Shade Lawn
Seed Mixture
5
4.5
3.5
3
2
Real-Kill Multi-Purpose Lawn and Garden Insect
Killer
4
Klay Soft Pelletized Gypsum Soil Conditioner
Klay Soft Pelletized Gypsum Soil Conditioner
Klay Soft Pelletized Gypsum Soil Conditioner
Lesco Pre-M 0.86% Plus Fertilizer 25-0-7
Lesco Starter Fertilizer 18-24-12
3
2.5
10
5
Real-Kill Multi-Purpose Lawn and Garden Insect
Killer
2
2.5
4.5
4
7
Rebels Supreme Blend Grass Seed for Sun and
Shade
4
4.2
4.2
4
5.5
Rebels Supreme Blend Grass Seed for Sun and
Shade
3.5
3.5
6.5
5
Lesco Turf Fertilizer 24-2-11
Lesco Weed and Feed
10
12.3
8.1
6
7
Ringer Lawn Restore 10-2-6
8
Master Turf Ultimate Tall Fescue Blend
Master Turf Ultimate Tall Fescue Blend
Milorganite 6-2-0
7.5
6
Sam’s Choice Crabgrass Preventer 30-3-4
Sam’s Choice Crabgrass Preventer 30-3-4
Sam’s Choice Crabgrass Preventer 30-3-4
Sam’s Choice Crabgrass Preventer 30-3-4
Sam’s Choice Insect Control Plus Fertilizer 28-4-6
Sam’s Choice Lawn Food 29-3-4
4
8
6.5
8
5.5
5
16
3.2
Milorganite 6-2-0
5.4
3
3.5
Miracle-Gro Lawn Fertilizer Plus Weed Control 28-
3-3
3
3.2
6
3.5
5.5
4
3.6
3.1
9.6
4.8
2.4
1.2
4
3.5
3
Miracle-Gro STarter Lawn Fertilizer 20-27-5
Miracle-Gro STarter Lawn Fertilizer 29-3-4
Ortho Lawn Insect Killer Granules
Ortho Lawn Insect Killer Granules
Ortho Lawn Insect Killer Granules
Ortho Lawn Insect Killer Granules
Ortho Max Insect Killer for Lawns
Ortho Max Insect Killer for Lawns
Ortho Max Insect Killer for Lawns
Sam’s Choice Starter Fertilizer 20-27-5
Sam’s Choice Starter Fertilizer 20-27-5
Scotts Classic Grass Seed Fall Grass Seed Mix
Scotts Classic Grass Seed Fall Grass Seed Mix
Scotts Grubex
3.6
4
5.5
3.5
2
5.5
3.5
2.5
4
2
2.3
3.1
2.3
1.4
1.5
4
Scotts Grubex Season Long Grub Control
Scotts Grubex Season Long Grub Control
Scotts Lawn Fungus Control
3.5
2.5
2
3
1
2
Specifications - 10
SPECIFICATIONS
b
b
lbs/1000 Flow
Materials
lbs/1000 Flow
Materials
square
feet
Control
square
feet
Control
Setting
at 3
Setting
at 3
a
a
mph
mph
2.7
2.2
1.1
2.5
4
Scotts Lawn Fungus Control
4
5.5
3.5
Wal Mart Gardens Kentucky 31 Tall Fescue
Wal Mart Weed and Feed 28-3-3
3.5
3
Scotts Pure Premium Kentucky Bluegrass Mix
Scotts Pure Premium Kentucky Bluegrass Mix
3.2
a. Flow Control Settings are based on 3 mph forward speed.
b. The products listed are the property of their respective owners, and are
not the property of, nor recommended by, Deere and Company.
4
Scotts Pure Premium Sun and Shade Grass Seed
Mixture
Calibration Settings
If the product you are using is not listed in the flow control setting table,
use the this calibration guide to set the flow control. Calibration guide
information is also provided on the hopper decal of the spreader.
1.25
3
Scotts Pure Premium Sun and Shade Grass Seed
Mixture
3.6
5.9
2.7
3.1
2.7
2.9
3.3
4.6
2.33
2.25
3
3.5
4.5
3.5
3
Scotts Starter Fertilizer 20-27-5
Scotts Starter Fertilizer 20-27-5
Scotts Turf Builder 28-3-8
Using application information on product package, find the calibration
setting in the following guide and set calibration control lever.
Adjust spread pattern.
Scotts Turf Builder Lawn Fertilizer 29-3-4
Scotts Turf Builder with Summer Guard
Scotts Turf Builder Plus Weed Control
Scotts Winterizer 22-4-1
Calibration settings have been determined using a 3 MPH pace or 40 ft. of
travel in 9 seconds.
3.5
3.5
3
Calibration Guide for Flow Control Settings
lbs/1000 square feet
0.5 - 0.9
Flow Control Setting
1
4.5
3.5
3.5
4
Sevin Lawn Insect Granules
1.0 - 1.4
2
Sevin Lawn Insect Granules
1.5 - 2.4
2.5
3
Sevin Lawn Insect Granules
2.5 - 3.4
Spectracide Grub Stop
3.5 - 3.9
3.5
4
3
2
Spectracide Traizicide Insect Killer Granules
Sta-Green Lawn Fertilizer 29-2-5
Sta-Green Lawn Weed Control
Sta-Green 200 Plus Weed and Feed 28-3-3
Sta-Green Starter Fertilizer 18-24-10
Sta-Green Weed and Feed 28-2-4
Sun and Shade Grass Seed Mixture
Sun and Shade Grass Seed Mixture
Vigoro Insect Control Plus Fertilizer
Vigoro Starter Fertilizer
4.0 - 4.4
3.6
2
3.5
3
4.5 - 4.9
4.5
5
5.0 - 5.9
3.2
3.6
3.2
10
5
3.5
3.5
3.5
7
6.0 - 7.4
5.5
6
7.5 - 8.9
9.0 - 10.9
11.0 - 12.9
13.0 - 14.9
15.0 - 17.9
18.0 - 20.9
21.0 - 24.5
6.5
7
5.5
2
7.5
8
3
3.6
3.5
3
4.5
3.5
3
9
Vigoro Turf Fertilizer 29-3-4
10
Vigoro Ultra Turf Winterizer 22-3-14
Vigoro Weed and Feed
3.2
4
4.5
5.5
Getting Quality Service
Wal Mart Gardens Kentucky Bluegrass Grass
Seed
John Deere Quality Continues with Quality Service
John Deere provides a process to handle your questions or problems,
should they arise, to ensure that product quality continues with quality
parts and service support.
2
8
3.5
7
Wal Mart Gardens Kentucky Bluegrass Grass
Seed
Wal Mart Gardens Kentucky 31 Tall Fescue
Follow the steps below to get answers to any questions you may have
Specifications - 11
GETTING QUALITY SERVICE
about your product.
1. Refer to your attachment and machine operator manuals.
2. In North America or Canada, call John Deere Special Services at 1-
866-218-8622 and provide product serial number (if available) and model
number.
Getting Quality Service - 12
GETTING QUALITY SERVICE
Getting Quality Service - 13
|