JVC DLA X590R User Manual

.
INSTRUCTIONS  
D-ILA  
PROJECTOR  
DLA-X990R  
DLA-X790R  
DLA-X590R  
MODE  
1
MODE  
2
MODE  
3
SETTING MEMORY  
ANAMO.  
HDR  
PICTURE  
MODE  
COLOR  
GAMMA  
PROFILE  
SETTINGS  
C.M.D.  
.
Mobile User Guide  
The Mobile User Guide can be viewed on mobile internet devices including  
smartphones and tablets.  
.
For Customer use :  
Pour utilisation par le client :  
Instrucción para el cliente :  
Enter below the serial No. which is  
located on the side of the cabinet.  
Retain this information for future  
reference.  
Entrerci-dessous le N°de série qui  
est situé sous le boîtier. Garder  
cetteinformation comme référence  
pour le futur.  
Introduzca a continuación el nº de  
serie que aparece en la parte  
inferior lateral de la caja. Conserve  
esta información como referencia  
para uso ulterior.  
Model No. DLA-X990R / DLA-X790R /  
DLA-X590R  
Serial No.  
N° de modèle DLA-X990R / DLA-X790R /  
DLA-X590R  
N° de série  
Modelo Nº DLA-X990R / DLA-X790R /  
DLA-X590R  
Nº de serie  
.
Not suitable for household room illumination.  
B5A-2360-12  
-
-
Power source indicated on the label. If you are not sure of  
the type of power supply to your home, consult your  
product dealer or local power company.  
IMPORTANT SAFEGUARDS  
Electrical energy can perform many useful functions.  
This unit has been engineered and manufactured to  
assure your personal safety. But IMPROPER USE  
CAN RESULT IN POTENTIAL ELECTRICAL  
SHOCK OR FIRE HAZARD. In order not to defeat  
the safeguards incorporated into this product,  
observe the following basic rules for its installation,  
use and service. Please read these Important  
Safeguards carefully before use.  
This product is equipped with a three-wire plug. This plug  
will fit only into a grounded power outlet. If you are unable  
to insert the plug into the outlet, contact your electrician to  
install the proper outlet. Do not defeat the safety purpose of  
the grounded plug.  
-
-
Power-supply cords should be routed so that they are not  
likely to be walked on or pinched by items placed upon or  
against them. Pay particular attention to cords at doors,  
plugs, receptacles, and the point where they exit from the  
product.  
-
-
-
All the safety and operating instructions should be read  
before the product is operated.  
For added protection of this product during a lightning  
storm, or when it is left unattended and unused for long  
periods of time, unplug it from the wall outlet and  
disconnect the cable system. This will prevent damage to  
the product due to lightning and power line surges.  
Do not overload wall outlets, extension cords, or  
convenience receptacles on other equipment as this can  
result in a risk of fire or electric shock.  
The safety and operating instructions should be retained for  
future reference.  
All warnings on the product and in the operating  
instructions should be adhered to.  
-
All operating instructions should be followed.  
Place the projector near a wall outlet where the plug can be  
easily unplugged.  
-
-
-
-
-
-
-
Unplug this product from the wall outlet before cleaning.  
Do not use liquid cleaners or aerosol cleaners. Use a damp  
cloth for cleaning.  
Never push objects of any kind into this product through  
openings as they may touch dangerous voltage points or  
short out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the product.  
Do not use attachments not recommended by the product  
manufacturer as they may be hazardous.  
-
-
Do not attempt to service this product yourself as opening  
or removing covers may expose you to dangerous voltages  
and other hazards. Refer all service to qualified service  
personnel.  
Do not use this product near water. Do not use immediately  
after moving from a low temperature to high temperature,  
as this causes condensation, which may result in fire,  
electric shock, or other hazards.  
Unplug this product from the wall outlet and refer service to  
qualified service personnel under the following conditions:  
-
-
Do not place this product on an unstable cart, stand, or  
table. The product may fall, causing serious injury to a child  
or adult, and serious damage to the product. The product  
should be mounted according to the manufacturer’s  
instructions, and should use a mount recommended by the  
When the power supply cord or plug is damaged.  
If liquid has been spilled, or objects have fallen on the  
product.  
a)  
b)  
manufacturer.  
PORTABLE CART WARNING  
If the product has been exposed to rain or water.  
If the product does not operate normally by following the  
operating instructions. Adjust only those controls that  
are covered by the Operation Manual, as an improper  
adjustment of controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the product to normal operation.  
c)  
d)  
(symbol provided by RETAC)  
When the product is used on a cart,  
care should be taken to avoid quick  
stops, excessive force, and uneven  
surfaces which may cause the product  
and cart to overturn, damaging  
equipment or causing possible injury to  
the operator.  
S3126A  
If the product has been dropped or damaged in any  
way.  
e)  
f)  
-
-
Slots and openings in the cabinet are  
provided for ventilation. These ensure reliable operation of  
the product and protect it from overheating. These  
openings must not be blocked or covered. (The openings  
should never be blocked by placing the product on bed,  
sofa, rug, or similar surface. It should not be placed in a  
built-in installation such as a bookcase or rack unless  
proper ventilation is provided and the manufacturer’s  
instructions have been adhered to.)  
When the product exhibits a distinct change in  
performance, this indicates a need for service.  
-
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer or with same characteristics as the original  
part. Unauthorized substitutions may result in fire, electric  
shock, or other hazards.  
To allow better heat dissipation, keep a clearance between  
this unit and its surrounding as shown below. When this unit  
is enclosed in a space of dimensions as shown below, use  
an air-conditioner so that the internal and external  
temperatures are the same. Overheating can cause  
damage.  
-
-
-
Upon completion of any service or repairs to this product,  
ask the service technician to perform safety checks to  
determine that the product is in proper operating condition.  
The product should be placed more than one foot away  
from heat sources such as radiators, heat registers, stoves,  
and other products (including amplifiers) that produce heat.  
When connecting other products such as VCR’s, and DVD  
players, you should turn off the power of this product for  
protection against electric shock.  
150 mm (6 in) and above  
300 mm  
300 mm  
(12 in) and  
above  
(12 in) and  
above  
150 mm  
(6 in) and  
above  
200 mm  
(8 in) and  
above  
Front  
.
3
-
-
-
-
-
Do not place combustibles behind the cooling fan. For  
example, cloth, paper, matches, aerosol cans or gas  
lighters that present special hazards when over heated.  
Do not look into the projection lens while the illumination  
lamp is turned on. Exposure of your eyes to the strong light  
can result in impaired eyesight.  
Not using the unit for a long time can lead to malfunction.  
Please power it on and let it run occasionally. Please avoid  
using the unit in a room where cigarettes are smoked. It is  
impossible to clean optical component parts if they are  
contaminated by nicotine or tar. This might lead to  
performance degradation.  
Do not look into the inside of this unit through vents  
(ventilation holes), etc. Do not look at the illumination lamp  
directly by opening the cabinet while the illumination lamp is  
turned on. The illumination lamp also contains ultraviolet  
rays and the light is so powerful that your eyesight can be  
impaired.  
Please watch from a distance three times the height of the  
projected image size. Persons with photosensitivity, any  
kind of heart disease, or weak health should not use 3D  
glasses.  
-
-
Watching 3D-images might be cause of illness. If you feel  
any change in your physical condition, please stop  
watching immediately and consult a physician if necessary.  
When watching 3D images, it is recommended to take  
regular breaks. As the length and frequency of the required  
breaks differ for every person, please judge according to  
your own condition.  
-
Do not drop, hit, or damage the light-source lamp (lamp  
unit) in any way. It may cause the light-source lamp to  
break and lead to injuries. Do not use a damaged light  
source lamp. If the light-source lamp is broken, ask your  
dealer to repair it. Fragments from a broken light-source  
lamp may cause injuries.  
-
If your child watches while wearing 3D glasses, it should be  
accompanied by its parents or an adult guardian. The adult  
guardian should be careful to avoid situations where the  
child’s eyes might become tired, as responses to tiredness  
and discomfort, etc., are hard to detect, and it is possible  
for the physical condition to deteriorate very quickly. As the  
visual sense is not yet fully developed in children under the  
age of 6, please consult a physician in regard to any  
problem concerning 3D-images if necessary.  
-
-
The light-source lamp used in this projector is a high  
pressure mercury lamp. Be careful when disposing of the  
light-source lamp. If anything is unclear, please consult  
your dealer.  
Do not ceiling-mount the projector to a place which tends to  
vibrate; otherwise, the attaching fixture of the projector  
could be broken by the vibration, possibly causing it to fall  
or overturn, which could lead to personal injury.  
Use only the accessory cord designed for this product to  
prevent shock.  
-
-
-
Note that when using the 3D feature, the video output may  
appear different from the original video image due to image  
conversion on the device.  
For health reasons, please take a break of about 5-15  
minutes every 30-60 minutes and let your eyes rest. Please  
refrain from watching any 3D-images when you feel tired,  
unwell or if you feel any other discomfort. Moreover, in case  
you see a double image, please adjust the equipment and  
software for proper display. Please stop using the unit if the  
double image is still visible after adjustment.  
* DO NOT allow any unqualified person to  
install the unit.  
Be sure to ask your dealer to install the unit  
(e.g.attaching it to the ceiling) since special  
technical knowledge and skills are required for  
installation. If installation is performed by an  
unqualified person, it may cause personal injury or  
electrical shock.  
-
-
Once every three years, please perform an internal test.  
This unit is provided with replacement parts needed to  
maintain its function (such as cooling fans). Estimated  
replacement time of parts can vary greatly depending on  
frequency of use and the respective environment. For  
replacement, please consult your dealer, or the nearest  
authorized JVC service center.  
-
Do not use optical instruments (such as magnifying glass or  
reflector) viewing the laser output. It may pose an eye  
hazard.  
When fixing the unit to the ceiling, Please note that we do  
not take any responsibility, even during the warranty period,  
if the product is damaged due to use of metal fixtures used  
for fixation to the ceiling other than our own or if the  
installation environment of said metal fixtures is not  
appropriate. If the unit is suspended from the ceiling during  
use, please be careful in regard to the ambient temperature  
of the unit. If you use a central heating, the temperature  
close to the ceiling will be higher than normally expected.  
Video images can burn into the electronic component parts.  
Please do not display screens with still images of high  
brightness or high contrast, such as found in video games  
and computer programs. Over a long period of time it might  
stick to the picture element. There is no problem with the  
playback of moving images, e.g. normal video footage.  
-
-
-
-
-
-
When turning on the projector, ensure that no one is looking  
into the projection lens.  
Do not look into the lens and openings when the light is on.  
Doing so would have serious effects on the human body.  
Do not detach or attach the projection lens with the power  
connected.  
Attempting to disassemble, repair or modify the projector  
yourself may lead to serious safety issues.  
Using a faulty product not only results in electrical shock or  
fire hazard, it can cause visual impairment.  
When abnormality occur, stop using the projector  
immediately and send it to your authorized dealer for repair.  
-
.
4
POWER CONNECTION  
For USA and Canada only  
IMPORTANT (Europe only):  
Use only the following power cord.  
The wires in the mains lead on this product are  
colored in accordance with the following code:  
Power cord  
: Earth  
: Neutral  
: Live  
Green-and-yellow  
Blue  
Brown  
As these colors may not correspond with the  
colored making identifying the terminals in your  
plug, proceed as follows:  
The power supply voltage rating of this product is  
AC100V – AC240V. Use only the power cord  
designated by our dealer to ensure Safety and EMC.  
Ensure that the power cable used for the projector is  
the correct type for the AC outlet in your country.  
Consult your product dealer.  
The wire which is colored green-and-yellow must be  
connected to the terminal which is marked M with  
the letter E or the safety earth or colored green or  
green-and-yellow. The wire which is colored blue  
must be connected to the terminal which is marked  
with the letter N or colored black.  
Power cord  
The wire which is colored brown must be connected  
to the terminal which is marked with the letter L or  
colored red.  
POWER CONNECTION  
(United Kingdom only)  
For United Kingdom  
For European continent  
countries  
IMPORTANT (Europe only):  
When replacing the fuse, be sure to use only a  
WARNING:  
correctly rated approved type, re-fit the fuse cover.  
Do not cut off the main plug from this  
equipment.  
IF IN DOUBT —— CONSULT A COMPETENT  
ELECTRICIAN.  
If the plug fitted is not suitable for the power points  
in your home or the cable is too short to reach a  
power point, then obtain an appropriate safety  
approved extension lead or adapter or consult your  
dealer. If nonetheless the mains plug is cut off,  
dispose of the plug immediately, to avoid a possible  
shock hazard by inadvertent connection to the main  
supply.  
Open the fuse compartment with the blade  
screwdriver, and replace the fuse.  
(* An example is shown in the illustration below.)  
WARNING:  
Fuse  
THIS APPARATUS MUST BE EARTHED.  
Dear Customer,  
This apparatus is in conformance with the valid  
European directives and standards regarding  
electromagnetic compatibility and electrical safety.  
European representative of  
JVC KENWOOD Corporation is:  
JVCKENWOOD Deutschland GmbH  
Konrad-Adenauer-Allee 1-11,  
61118 Bad Vilbel,  
GERMANY  
.
5
ENGLISH  
Information for Users on Disposal of Old Equipment and Batteries  
[European Union only]  
These symbols indicate that equipment with these symbols should not be disposed  
of as general household waste. If you want to dispose of the product or battery,  
please consider the collection systems or facilities for appropriate recycling.  
Notice: The sign Pb below the symbol for batteries indicates that this battery contains lead.  
Battery  
Products  
FRANÇAIS  
Informations relatives à l’élimination des appareils et des piles usagés, à l’intention des utilisateurs  
[Union européenne seulement]  
Si ces symboles figurent sur les produits, cela signifie qu’ils ne doivent pas être jetés  
comme déchets ménagers. Si vous voulez jeter ce produit ou cette pile, veuillez  
considérer le système de collecte des déchets ou les centres de recyclage appropriés.  
Notification: La symbole Pb en dessous du symbole des piles indique que cette  
Pile  
pile contient du plomb.  
Produits  
ESPAÑOL / CASTELLANO  
Información para los usuarios sobre la eliminación de baterías/pilas usadas  
[Sólo Unión Europea]  
Estos símbolos indican que el equipo con estos símbolos no debe desecharse  
con la basura doméstica. Si desea desechar el producto o batería/pila, acuda  
a los sistemas o centros de recogida para que los reciclen debidamente.  
Atención: La indicación Pb debajo del símbolo de batería/pila indica que ésta  
Baterías/pilas  
contiene plomo.  
Productos  
DEUTSCH  
Benutzerinformationen zur Entsorgung alter Geräte und Batterien  
[Nur Europäische Union]  
Diese Symbole zeigen an, dass derartig gekennzeichnete Geräte nicht als normaler  
Haushaltsabfall entsorgt werden dürfen. Wenden Sie sich zur Entsorgung des  
Produkts oder der Batterie an die hierfür vorgesehenen Sammelstellen oder  
Einrichtungen, damit eine fachgerechte Wiederverwertung möglich ist.  
Batterie  
Hinweis: Das Zeichen Pb unterhalb des Batteriesymbols gibt an, dass diese  
Produkte  
Batterie Blei enthält.  
ITALIANO  
Informazioni per gli utenti sullo smaltimento delle apparecchiature e batterie obsolete  
[Solo per l’Unione Europea]  
Questi simboli indicano che le apparecchiature a cui sono relativi non devono  
essere smaltite tra i rifiuti domestici generici. Se si desidera smaltire questo  
prodotto o questa batteria, prendere in considerazione i sistem i o le strutture di  
raccolta appropriati per il riciclaggio corretto.  
Batteria  
Nota: Il simbolo Pb sotto il simbolo delle batter ie indica che questa batteria contiene piombo.  
Prodotti  
NEDERLANDS  
Informatie voor gebruikers over het verwijderen van oude apparatuur en batterijen  
[Alleen Europese Unie]  
Deze symbolen geven aan dat apparatuur met dit symbool niet mag worden  
weggegooid als algemeen huishoudelijk afval. Als u het product of de batterij wilt  
weggooien, kunt u inzamelsystemen of faciliteiten voor een geschikte recycling  
gebruiken.  
Batterij  
Opmerking: Het teken Pb onder het batterijsymbool geeft aan dat deze batterij lood bevat.  
Producten  
.
6
Location information of the labels  
As with any bright light source, do not stare into the  
beam, RG2 IEC 62471-5:2015  
.
7
Contents  
Getting Started  
Set up  
Maintenance  
Troubleshooting  
Others  
Operate  
Symbols used in this manual  
M
N
O
indicates a function that is supported by DLA-X990R.  
indicates a function that is supported by DLA-X790R.  
indicates a function that is supported by DLA-X590R.  
Adjust/Set  
Items not marked with any of the above symbols are  
supported by all models.  
8
Accessories/Optional Accessories  
Check the Accessories  
Lens cover O .................................................................... 1 piece  
* It is attached to the main unit at the time of shipment.  
.
Remote control ....................................................................... 1 piece  
.
AAA-size batteries (for operational check) ............................ 2 pieces  
.
Power cord (for USA) (about. 2 m) (about. 78.7 in) ................. 1 piece  
.
0
Quick User Guide, safety precautions, warranty card, and other printed material are also included.  
Be sure to read the “Safety Precautions” before using this projector.  
0
Optional Accessories  
0
Replacement lamp: Product no. PK-L2615U  
3D Glasses: model PK-AG3  
3D Synchro Emitter: model PK-EM2  
0
0
Compatibility Chart for 3D Synchro Emitter and 3D Glasses  
3D Glasses  
PK-AG1 *  
PK-AG2 *  
PK-AG3  
(Communication  
(Communication  
(Communication  
Method: IR (Infrared)) Method: IR (Infrared)) Method: RF (Radio  
frequency))  
X
X
3D Synchro Emitter  
PK-EM1 *  
(Communication  
Method: IR (Infrared))  
X
PK-EM2  
(Communication  
Method: RF (Radio  
frequency))  
* Discontinued product  
Please check with your authorized dealer for details.  
9
                 
Controls and Features  
Main Unit - Front  
D
E
E
C
AB  
.
A
D
Lens  
Indicator  
This is a projection lens. Do not look through the lens  
while an image is projected.  
E
Exhaust vent  
B
Lens cover M N  
Warm air is discharged to cool down the internal  
temperature.  
Do not block the vents.  
The lens cover opens/closes when the power supply  
is turned on/off. (P. 51)  
For O, attach the lens cover when the unit is not in  
use.  
0
C
Remote Sensor (front)  
Please aim the remote control at this area when using  
it.  
* There is also a remote sensor at the rear.  
Main Unit - Bottom  
F
Inlets (at 3 points on the rear/bottom)  
F
G
The inlets take in air to cool down the internal temperature.  
Do not block or prevent the outflow of hot air. Doing so may cause  
the unit to malfunction.  
* There are two inlets on the right and left sides at the rear of the unit.  
G
Manual button for lens cover M N  
The lens cover can be opened when pressed down.  
It is used for maintenance purposes. You can also make use of it  
when you need to open the lens cover urgently.  
H
H
Feet  
The height and angle of the projector can be adjusted by turning the  
foot. (0 to 5 mm) (0 to 0.2 in) (P. 17)  
When the foot is removed, it can be used as the mounting holes for  
the ceiling mount bracket.  
10  
           
Main Unit - Rear  
F
J
F
I
M
L K  
.
I
L
Input terminals  
Remote sensor (rear)  
In addition to the video input terminal, there are also  
other connection terminals for devices such as  
controllers and optional equipment.  
more details about the terminals.  
Please aim the remote control at this area when using  
it.  
* There is also a remote sensor at the front.  
M
Power input terminal  
Connect the supplied power cord to this terminal.  
J
K
Lamp cover  
When replacing the light source lamp, remove this  
cover.  
Operation panel  
For more details, please refer to the “Operation  
Operation panel  
A [STANDBY/ON]:Turns “on”/“off” the  
power  
[INPUT]: Switches the input  
[OK]: Confirms a selection  
[JKH I] keys: Selects an item  
[MENU]: Displays the menu  
[BACK]: Returns to the previous menu  
.
11  
     
Main Unit - Input Terminals  
Enlarged View of Rear Face  
A
B
C
D
E
F
.
A
B
F
[HDMI 1] input terminal  
[HDMI 2] input terminal  
[TRIGGER] terminal (E)  
Output terminal for DC 12 V, 100 mA power supply. It  
is used for sending output signals to control devices  
such as an elevating screen that is equipped with a  
trigger function.  
For connecting to devices that support HDMI output.  
Note that improper connection may damage the  
projector. (Tip=DC +12 V, Sleeve=GND)  
It is fitted to the M3 lock hole. The depth of the screw  
hole is 3 mm (0.1 in).  
C
[LAN] terminal (RJ-45)  
The projector can be controlled by connecting it to a  
PC through the computer network for control  
commands to be sent to the projector.  
D
[RS-232C] terminal (D-sub 9-pin  
male)  
The projector can be controlled by connecting a PC to  
this terminal.  
E
[3D SYNCHRO] terminal  
By connecting a 3D Synchro Emitter (sold separately)  
to this terminal, you can view 3D movies.  
12  
   
Remote Control  
A
B
C
O
B [STAND BY]  
[PICTURE MODE]  
Switches the picture mode.  
Turns off the power. (P. 22)  
C [ON]  
A
0
Press [NATURAL], [CINEMA] or  
[HDR] to switch to the respective  
picture mode.  
Pressing [PICTURE MODE]  
displays the Picture mode  
selection menu.  
Turns on the power. (P. 21)  
B
C
[INPUT]  
0
Switches the input to [HDMI 1] or  
INPUT  
HDMI 1  
HDMI 2  
INFO.  
D
E
D
E
[INFO.]  
P
Q
R
[COLOR PROFILE]  
MODE1  
MODE2  
MODE3  
Displays the information menu.  
Displays the color profile selection  
menu. (P. 31)  
SETTING MEMORY  
[SETTING MEMORY]  
[GAMMA SETTINGS]  
LENS  
CONTROL  
Retrieves the [MODE 1] (LENS  
MEMORY 1), [MODE 2] (LENS  
MEMORY 2) or [MODE 3] (LENS  
MEMORY 3) lens memory.  
LENS AP. ANAMO.  
F
G
H
Displays the gamma setting  
menu.  
[ADVANCED MENU]  
Pressing the button each time  
switches the menu in the following  
sequence: “Picture Mode” "  
“Color Profile” " “Color Temp.” "  
“Gamma” " “Blur Reduction”...  
F
[LENS CONTROL]  
I
J
For adjusting focus, zoom, and  
0
Pressing the button each time  
switches the function in the  
following sequence: “Focus” "  
“Zoom” " “Shift”...  
K
L
M
S
[MPC]  
Displays the MPC setting menu.  
T
G
[LENS AP.]  
For setting the lens aperture.  
[C.M.D.]  
N
O
PICTURE MODE  
For setting frame interpolation.  
NATURAL  
CINEMA  
HDR  
H
[ANAMO.]  
P
Q
0
Pressing the button each time  
switches the frame interpolation in  
sequence.  
Switches the anamorphic mode.  
PICTURE  
MODE  
COLOR  
GAMMA  
PROFILE  
SETTINGS  
0
Pressing the button each time  
switches the anamorphic mode in  
sequence.  
R
S
T
U
V
W
X
ADVANCED  
MENU  
MPC  
C.M.D.  
U
[GAMMA]  
3D  
I
COLOR  
TEMP.  
PIC.  
[HIDE]  
GAMMA  
FORMAT  
ADJ.  
0
Pressing the button each time  
switches the configurable gamma  
in sequence.  
Hides the image temporarily.  
J
[LIGHT]  
V
[COLOR TEMP.]  
Illuminates the buttons on the  
Switches the color temperature.  
remote control.  
K
L
M
[JKH I] keys  
0
Pressing the button each time  
switches the configurable color  
temperature in sequence.  
For selecting an item.  
[OK]  
W
[3D FORMAT]  
Confirms a selected item.  
For setting the 3D format.  
[MENU]  
Displays the menu, or hides the  
0
Pressing the button each time  
switches the 3D format in  
sequence.  
menu if it is displayed.  
N
[BACK]  
Returns to the previous menu.  
X
[PIC. ADJ.]  
Displays the picture quality  
adjustment gauge. (P. 48)  
0
Pressing the button each time  
displays the picture quality  
adjustment gauge in sequence.  
13  
         
Loading Batteries into the Remote Control  
0
If the remote control has to be brought closer to the unit  
Loading the batteries  
to operate, it means that the batteries are wearing out.  
Replace the batteries with new ones (AAA).  
.
0
0
Insert the batteries according to the t s marks.  
Be sure to insert the s end first.  
When removing the battery, do so from the t end.  
If an error occurs while using the remote control,  
remove the batteries and wait for five minutes. Load  
the batteries again and operate the remote control.  
CAUTION  
Removing the batteries  
0
Do not put the remote control in a place with an  
exposure to direct sun light or high temperature.  
It may deformed due to heat, or the internal  
components may be adversely affected resulting in  
fire hazard.  
.
0
Remove the batteries from the remote control when  
storing the remote control.  
Storing the remote control for a prolonged period  
without removing the batteries can cause battery  
leakage.  
Effective Range of Remote Control Unit  
When aiming the remote control toward the sensor on this  
Control through reflection off a screen, etc.  
Ensure that the total of distance A (between this unit and  
the screen) and distance B (between the remote control  
and the screen) is within 7 m.  
unit (front or rear), ensure that the distance to the sensor  
is within 7 m.  
If the remote control fails to work properly, move closer  
to this unit.  
* As the efficiency of signals reflected from the remote  
control unit varies with the type of screen used, the  
operable distance may decrease.  
This unit  
30°  
30°  
Screen  
20°  
20°  
30°  
30°  
20°  
20°  
This unit  
Remote Control  
A
.
B
Remote Control  
.
CAUTION  
0
Do not put the remote control in a place with an exposure to direct sun light or high temperature.  
It may deformed due to heat, or the internal components may be adversely affected resulting in fire hazard.  
0
Remove the batteries from the remote control when storing the remote control.  
Storing the remote control for a prolonged period without removing the batteries can cause battery leakage.  
14  
     
Installing the Projector  
Precautions during Installation  
Please read the following carefully before installing this  
unit.  
Using the projector  
This unit uses a projection lamp, which will heat up when  
in use.  
Do not install at the following  
This unit is a precision device. Please refrain from  
installing or using it at the following locations. Otherwise,  
it may cause fire or malfunction.  
Please refrain from projecting in the following  
circumstances. Otherwise, it may cause fire or  
malfunction.  
0
Projection with the unit stood vertically  
0
Dusty, wet and humid places  
Places subject to oily smoke or cigarette smoke  
On top of a carpet or bedding, or other soft surfaces  
Places exposed to direct sunlight  
0
0
0
0
Places with a high or low temperature  
.
0
Do not install this unit in a room that is oily or subject  
0
Projection with the unit inclined at an angle  
to cigarette smoke. Even a small quantity of smoke or  
Horizontal inclination: within ± 5 °  
oiliness can have a long-term impact on this unit.  
* This unit produces a great amount of heat, and is  
designed to take in cool air to cool its optical  
components. Using the unit at the above locations  
may cause dirt to attach to the light path, thereby  
resulting in dark images or dull colors.  
5°  
5°  
.
Vertical inclination: within ± 15 °  
* Dirt that sticks to the optical components cannot be  
removed.  
.
Maintain clearance from the wall, etc.  
As the unit discharges a large amount of heat, install it  
with adequate clearance from the surroundings as shown  
below.  
.
0
150 mm (6 in) and above  
Malfunction may occur if the angle is not set within the  
abovementioned range.  
300 mm  
(12 in) and  
above  
300 mm  
(12 in) and  
above  
Installing the screen  
Install the unit and the screen such that they are  
perpendicular to each other.  
150 mm  
(6 in) and  
above  
Screen  
200 mm  
(8 in) and  
above  
Front  
Front  
.
Leave the front area of the unit unblocked.  
If there is any obstructing object in front of the exhaust  
vent, hot air will flow back to the unit and cause it to heat  
up. Hot air flowing out of the unit may cast shadows on  
the screen (heat haze phenomenon).  
0
Please choose a screen material with non-uniform  
patterns. Uniform patterns such as checks may cause  
interference patterns to occur.  
0
In this case, you can change the size of the screen to  
make the interference patterns less noticeable.  
Using the projector at a high altitude  
When using this unit at a location that is higher than 900  
m (3,000 ft) above sea level (low air pressure), set “High  
Altitude Mode” to “On”. (P. 53)  
15  
     
Precautions during Mounting  
Securing (mounting) the projector  
Securing the projector (ceiling mount)  
.
0
Be sure to ask your dealer to install the unit for you.  
Installing the unit on your own may cause the unit to  
fall resulting in injury.  
0
0
Take the necessary actions to prevent the main unit  
from falling off such as during an earthquake.  
.
Regardless of the warranty period, JVC is not liable for  
any product damage caused by mounting the unit with  
non-JVC ceiling fittings or to an environment that is not  
suited for ceiling mount.  
When using the unit with it suspended from a ceiling,  
pay attention to the surrounding temperature. When a  
heater is in use, the temperature around the ceiling  
may be higher than expected.  
To attach the unit to the ceiling mount bracket, set the  
torque between the range of 1.5N m to 2.0N m.  
Tightening with torque exceeding the above range  
may cause damage to the unit, which may result the  
unit to fall.  
Install the outlet at an accessible height to unplug from  
the wall. Or install the circuit breaker at an accessible  
height to shut down the projector. If you need  
information, please consult your authorized dealer or  
specialist.  
0
0
When this unit is to be mounted to a fixed position for  
use, install it horizontally.  
Make sure to secure the main unit to prevent accidents  
such as during an earthquake.  
0
0
Securing with screws  
4 Locations  
Air Inlets  
0
.
Remove the four feet at the bottom, and fasten using the  
screws (M5 screws, 13 to 23 mm).  
* Using screws other than those designated may cause  
the unit to break down.  
* Leave a clearance of at least 10 mm (0.4 in) from the  
bottom surface of the unit to allow it to take in cool air.  
16  
   
Adjusting the Position  
Adjusting the elevation angle of the projector  
Adjusting the position of the image  
The height and inclination of the unit (0 to 5 mm (0 to 0.2  
By using the lens shift feature of this unit, you can shift  
the image upward/downward or to the left/right. Set it to  
your preferred position.  
in)) can be adjusted by turning the feet.  
Lift the unit and adjust the four feet.  
Horizontal Position  
Vertical Position: 0% (Center)  
Up to about 34% of the  
projected image  
Feet  
Vertical Position  
Horizontal Position: 0 % (Center)  
Up to about 80% of the  
projected image  
Extend  
Contract  
.
Lens shift Range  
90  
80  
70  
60  
50  
40  
30  
20  
10  
Lens movement range  
0
10 20 30 40  
Horizontal lens shift (%)  
.
0
The maximum vertical shift varies with the amount of  
horizontal shift. Similarly, the maximum horizontal shift  
also changes with the amount of vertical shift.  
The values on the graph are intended as a guide. Use  
them for reference during installation.  
0
17  
   
Connecting the Projector  
0
Do not turn on the power until connection is complete.  
The connection procedures differ according to the device used. For details, please refer to the instruction manual of  
the device to be connected.  
This projector is used for projecting images. To output the audio of connected devices, please connect a separate  
audio output device, such as an amplifier or speaker.  
0
0
0
The images may not be displayed depending on the devices and cables to be connected.  
A high speed HDMI cable (sold separately) that is HDMI-certified is recommended.  
When using a standard cable, you are recommended to set the resolution of the equipment transmitting the video to  
1080i or lower.  
0
Also, please refer to “HDMI2 EDID”P. 50.  
Some cables cannot be connected to this unit due to the size of their connector cover.  
0
Connecting to the HDMI Input Terminal (Digital Input)  
Connecting via HDMI cable  
This Unit  
Laptop, etc.  
BD/DVD Recorder, etc.  
To [HDMI 1] or [HDMI 2] input  
terminal  
HDMI Output Terminal  
HDMI Cable (Sold Separately)  
.
0
If noise occurs, move the laptop away from this unit.  
Connecting through an AV amplifier  
This Unit  
Speakers  
BD/DVD Recorder, etc.  
HDMI Cable  
(Sold Separately)  
To [HDMI 1] or [HDMI 2] input  
terminal  
Speaker Cable  
HDMI Cable (Sold Separately)  
(Sold Separately)  
AV Amplifier  
.
0
If the source device is connected to the projector through an intermediate device such as an AV amplifier or divider,  
the video image may not appear depending on the specifications of the intermediate device.  
In this case, connect the source device directly to the projector, and check whether the video image is displayed.  
18  
         
Connecting via HDMI-DVI conversion cable  
Desktop PC, etc.  
This Unit  
To [HDMI 1] or [HDMI 2] input  
terminal  
DVI Output Terminal  
HDMI-DVI Conversion Cable (Sold Separately)  
If noise occurs, move the desktop PC away from this unit.  
.
0
0
If the video is not displayed, try to reduce the length of the cable or lower the resolution of the video transmitting  
equipment.  
Connecting to the LAN Terminal  
Hub  
This Unit  
To [LAN] Terminal  
Connection Cable  
Network  
(Sold Separately)  
Server  
Desktop PC, etc.  
.
0
0
0
0
The network is used to control this unit. It is not used for sending or receiving video signals.  
Please contact your network administrator for information concerning the network connection.  
Set “ECO Mode” to “Off” if LAN communication is performed in the Standby mode. (P. 58)  
Connecting to the RS-232C Terminal  
This Unit  
Laptop, etc.  
To [RS-232C] Terminal  
RS-232C Terminal  
RS-232C Connection Cable (Sold Separately)  
.
0
0
Set “ECO Mode” to “Off” if RS-232C communication is performed in the Standby mode. (P. 58)  
19  
     
Connecting to the TRIGGER Terminal  
Screen  
This Unit  
To [TRIGGER] Terminal  
Trigger Input Terminal (Ø3.5)  
Trigger Cable (Sold Separately)  
.
0
0
0
0
0
Do not use it to supply power to other devices.  
Connecting to the audio terminal of another device may cause the device to malfunction or break down.  
Using beyond the rated value will cause the unit to malfunction.  
The trigger terminal outputs a voltage of 12 V. Exercise adequate caution to prevent short circuit.  
The factory setting is “Off”. To change the setting, configure the “Trigger” item in the menu (P. 57).  
Connecting the Power Cord (Supplied Accessory)  
A
Connect the power cord supplied to the power input terminal on  
the main unit  
B
Insert the supplied power plug into the wall outlet.  
A
Power Cord  
(Supplied)  
B
Precautions to prevent fire and electric shock  
0
The power consumption of this unit is large. Please connect it directly to the wall outlet.  
When you are not using the projector, please unplug the power cord from the outlet.  
Connect it using only the power cord supplied.  
0
0
0
0
Do not use a voltage other than the indicated power voltage.  
Do not damage, break or modify the power cord. Do not place a heavy object on the power cord, or heat or pull it.  
Doing so may damage the power cord.  
0
Do not unplug the power cord with wet hands.  
20  
     
Viewing Videos  
STANDBY/ON  
LAMP  
WARNING  
MEMO  
0
0
When you are using O, be sure to remove the lens cover.  
Connect the power cord, and ensure that the “STANDBY/ON” indicator  
lights up in red.  
1
Turn on the power  
O
Remote control: press the C [ON] button  
Projector unit: press the A [STANDBY/ON] button  
Remote Control  
0
The “STANDBY/ON” indicator light switches from red to green (light  
goes off after the unit starts up).  
0
(M N) The lens cover opens.  
3
2
1
“STANDBY/ON” lights up (red)  
In standby state  
“STANDBY/ON” lights up (green)  
During lamp startup  
MODE 1  
MODE 2  
MODE 3  
S
TANDBY
/ON  
LAMP  
WARNING  
S
TANDBY
/ON  
LAMP  
WARNING  
SETTING MEMORY  
.
This unit  
2
Choose the image to project  
1 3  
2
Remote control: press the [HDMI 1] or [HDMI 2] button  
Projector unit: press the [INPUT] button to switch the input  
0
Play back the selected device to project the image.  
To hide the image temporarily  
Press the [HIDE] button on the projector unit or remote control  
0
The “STANDBY/ON” indicator light starts to blink in green.  
Press the [HIDE] button again to resume display of the image.  
The power cannot be turned off when the image is temporarily  
hidden.  
0
0
21  
         
3
Turn off the power  
Remote control: press the B [STAND BY] button  
Projector unit: press the A [STANDBY/ON] button  
0
While the “Are you sure you want to turn off?” message is displayed, press the button again.  
The lamp turns off, and the “STANDBY/ON” indicator switches from a green light to a red blinking light.  
After the light goes off, the fan will run for about 100 seconds to cool down the lamp (Cool-down mode).  
Do not disconnect the power cable while cooling is in progress.  
0
0
0
After about 100 seconds, the “STANDBY/ON” indicator switches from a blinking red to a solid red light.  
“STANDBY/ON” blinking (red)  
“STANDBY/ON” lights up (red)  
In the Cool-down mode  
In standby state  
STANDBY/ON  
LAMP  
WARNING  
STANDBY/ON  
LAMP  
WARNING  
.
0
0
For O, attach the lens cover manually.  
For M N, the lens cover closes upon power off.  
CAUTION  
0
0
0
0
The power cannot be turned off within approximately 60 seconds after it has been turned on.  
The power cannot be turned on again while cooling is in progress (100 seconds).  
Pull out the power plug when the unit is not to be used for a prolonged period of time.  
If the indication of indicator differs from the description, refer to “Indicator Display on the Main Unit”P. 79 for details.  
22  
 
Adjusting the Projector Screen  
Adjusting the Lens According to the Projection Position  
Press the [LENS CONTROL] button, and use the [JKH I]  
1
keys to adjust Focus, Zoom (screen size), and Shift (screen  
position)  
Focus  
MODE 1  
MODE 2  
MODE 3  
SETTING MEMORY  
ANAMO.  
1
2
.
0
0
0
Pressing the [LENS CONTROL] or [OK] button each time switches the mode  
in the following sequence: “Focus” " “Zoom” " “Shift” " “Focus”...  
Operation of the lens control feature is disabled when the lens lock is set to  
“On”. (P. 51)  
For more detailed information, please refer to “Lens Control”P. 51.  
HDR  
PICTURE  
MODE  
COLOR  
GAMMA  
PROFILE  
SETTINGS  
ABCD  
C.M.D.  
Focus Adjustment  
Zoom (Screen Size)  
Adjustment  
Shift (Screen Position)  
Adjustment  
.
Press the [MENU] button once, or the [BACK] twice, to end  
adjustment.  
2
23  
       
Saving and Retrieving Adjustment Settings  
The Focus, Zoom, and Shift settings can be saved or retrieved, so you can switch  
easily to a different aspect ratio (screen size) according to the image.  
0
In a state where no adjustment settings are saved (factory default), only “Lens  
Memory Save” is displayed.  
0
Operation of the lens control feature is disabled when the lens lock is set to “On”.  
Saving an adjustment data  
MODE 1  
MODE 2  
MODE 3  
SETTING MEMORY  
Adjust focus, zoom, or shift (P. 23)  
1
ANAMO.  
Press the [MENU] button to display the menu and select  
2
“Installation”"“Lens Control”"“Lens Memory Save”  
Installation  
>> Lens Memory Save  
3
-----  
-----  
-----  
-----  
-----  
-----  
-----  
-----  
-----  
-----  
2 4  
HDR  
PICTURE  
MODE  
COLOR  
GAMMA  
PROFILE  
SETTINGS  
Operate  
Exit  
MENU  
Back  
BACK  
Select  
.
C.M.D.  
Select the item to save, and press the [OK] button  
3
4
0
The adjustment data is saved.  
0
Items with no adjustment data saved are displayed as [----].  
0
If you have selected an item for which an adjustment data has already been  
saved, the old data will be overwritten.  
0
You can change the name when saving an item. (P. 25)  
0
The maximum number of items can be saved is 10 for M N and 5 for  
O.  
Press the [MENU] button to exit  
24  
     
Retrieving an adjustment data  
Press the [MENU] button to display the menu and select “Installation”"“Lens  
1
Control”"“Lens Memory Select”  
0
The data can also be retrieved using the direct keys on the remote control. The [MODE1] to [MODE3] keys  
correspond to MEMORY 1 to MEMORY 3.  
Installation  
>> Lens Memory Select  
MEMORY1  
MEMORY2  
-----  
-----  
-----  
-----  
-----  
-----  
-----  
-----  
Operate  
Exit  
MENU  
Back  
BACK  
Select  
.
Select the adjustment data to retrieve, and press the [OK] button  
2
0
The retrieved data is adjusted automatically.  
0
If no adjustment data has been saved, the item will be grayed out and cannot be selected.  
Renaming an adjustment data  
Press the [MENU] button to display the menu and select “Installation” “Lens  
"
1
Control” “Lens Memory Name Edit”  
"
Installation  
>> Lens Memory Name Edit  
MEMORY1  
MEMORY2  
-----  
-----  
-----  
-----  
-----  
-----  
-----  
-----  
Operate  
Exit  
MENU  
Back  
BACK  
Select  
.
Select the adjustment data to edit, and press the [OK] button  
2
0
An edit screen appears.  
Installation  
Lens Memory Name Edit  
>>  
Name MEMORY1  
Input Cursor  
A
N
a
B
O
b
C
P
c
D
Q
d
E
R
e
r
F
S
f
s
6
&
)
G
T
g
t
7
*
H
U
h
y
8
+
I
V
i
v
9
-
J
W
j
w
0
/
K
X
k
x
,
L
Y
l
y
.
M
Z
m
z
^
Selection Cursor  
n
o
p
q
Character List  
1
!
2
"
;
3
#
|
4
$
~
5
%
(
@
=
?
:
<
>
[
]
{
}
\
Clear  
All Clear  
OK  
SPACE  
Exit  
Operate  
Back  
MENU  
BACK  
Select  
.
0
0
0
You can input up to 10 characters.  
Characters that are usable include alphabets (upper or lower case), numeric characters, and symbols.  
Pressing the [Back] button cancels the content that is currently being edited, and exits the edit mode.  
After renaming, select “OK” and press the [OK] button  
Press the [MENU] button to exit  
3
4
25  
   
Setting Screen Correction  
1
Set Screen Adjust  
MEMO  
By selecting the optimal correction mode  
according to the characteristics of the screen in  
use, corrections can be performed to reproduce  
natural images with balanced colors.  
0
You can utilize the optional optical sensor and  
dedicated projector calibration software to make finer  
adjustments.  
For details on the dedicated projector calibration  
software, please visit our website.  
Installation  
Lens Control  
Pixel Adjust  
Installation Style  
Keystone  
Anamorphic  
Front  
0
Off  
Off  
High Altitude Mode  
Screen Adjust  
Screen No.  
Off  
2
3
1
Operate  
Exit  
Back  
MENU  
BACK  
Select  
.
0
0
This item is not available when “Color Profile” is  
set to “Off”.  
For information on the screen and the  
corresponding correction mode, please visit our  
website.  
26  
 
Adjusting the Screen Size (Aspect)  
The screen size of the projected image can be adjusted  
optimally according to the original screen size (aspect)  
that has been input.  
Example of input image and screen size  
HDMI Signal Input  
.
Press the [MENU] button to display  
the menu  
1
Output Image  
Input Image  
Setting  
16:9  
4:3  
Zoom  
Select “Input Signal” " “Aspect” in the  
menu, then select the setting and  
press [OK]  
4:3  
2
2.35:1  
(Cinema  
Scope)  
Input Signal  
Input Level  
Color Space  
Aspect  
Auto  
Auto  
16:9  
Auto  
PC Signal Input  
Progressive  
Mask  
3D Setting  
Picture Position  
HDMI2 EDID  
.
A
Output Image  
Input Image  
Setting  
Just  
Auto  
Full  
Operate  
Exit  
Back  
BACK  
MENU  
Select  
.
1280×1024  
Setting  
4:3  
Description  
Sets the screen size to 4:3. For Displayed  
HD signals, the two sides are only during  
reduced.  
video signal  
input.  
16:9  
Sets the screen size to 16:9.  
For SD signals, the two sides  
are expanded.  
Zoom  
Enlarges the entire image.  
* Not selectable in the case of  
HD signals.  
Auto  
Positions the image at the  
Displayed  
center with the entire image only during  
enlarged.  
PC signal  
input.  
Just  
Full  
Displays the input image in the  
actual size.  
Fills the entire screen with the  
image with the size (aspect) of  
the input image ignored.  
0
This item is grayed out and cannot be adjusted when  
there is no signal, signal is out of range, or during 3D  
or 4K input.  
3
Press the [MENU] button to exit  
27  
 
Viewing 3D Movies  
By using the 3D Glasses (PK-AG1, PK-AG2, or PK-AG3) and 3D Synchro Emitter (PK-EM1 or PK-EM2), both sold  
separately, you can enjoy 3D video images.  
0
For 3D Glasses and 3D Synchro Emitter that are compatible with this unit, please refer to “Optional  
Installing the 3D Synchro Emitter  
1
Connect 3D Synchro Emitter to the [3D SYNCHRO] terminal on the main unit  
Installation Example  
This Unit  
3D GLASSES  
PK-AG3  
3D SYNCHRO EMITTER  
PK-EM2  
.
CAUTION  
0
If PK-EM1 is used, adjust the position of the 3D Synchro Emitter such that the 3D Glasses can receive the signal  
from the 3D Synchro Emitter.  
For more details, please refer to the instruction manual of PK-EM1.  
28  
       
Viewing 3D Movies  
Connect this unit to a 3D-compatible  
Format  
Description  
1
HDMI device, and turn on the power  
to play back the 3D video image  
Auto  
Automatically determines and  
sets the format upon receiving 3D  
signal.  
0
For details on how to play back 3D video images,  
please refer to the instruction manual of the  
player or recorder in use.  
Side by Side  
Top and Bottom  
2D  
Select this setting if the 3D input  
signal is of the side-by-side  
format.  
0
This unit supports the following 3D formats.  
- Frame packing  
- Side-by-side  
Select this setting if the 3D input  
signal is of the top-and-bottom  
format.  
- Top-and-bottom  
Setting the 3D format  
Select this setting if 2D images  
are falsely recognized as 3D  
ones.  
A
Select “3D Format”  
HDR  
* If a signal cannot be displayed as 3D image,  
selecting the format does not switch the signal  
to a 3D image.  
PICTURE  
MODE  
COLOR  
GAMMA  
PROFILE  
SETTINGS  
3D  
FORMAT  
C.M.D.  
.
For more information on possible input signals,  
0
Pressing the [3D FORMAT] button each time  
switches the mode in the following sequence:  
“Auto” " “Side by Side” " “Top and Bottom” "  
“2D” " “Auto”...  
* In the default setting, “3D Format” is set to “Auto”  
for automatic projection of 3D images.  
0
You can also perform setting from “Input  
Signal”"“3D Setting”"“3D Format” in the  
menu.  
Turn of the power of the 3D Glasses  
and put them on  
2
0
The PK-AG1 powers on automatically.  
Adjusting 3D Movies  
3D video images may appear differently to different  
viewers. It may also be affected by your physical  
condition at the time of viewing.  
Adjusting parallax (Parallax)  
Adjust the displacement of the image for the left  
and right eyes separately to obtain the best 3D  
effect.  
You are therefore recommended to adjust the video  
images accordingly.  
0
To do so, use the H I keys to move the cursor.  
Setting range: -15 to +15  
Select “Input Signal”"“3D Setting”  
0
1
from the menu  
Adjusting crosstalk (Crosstalk Cancel)  
Double images (overlapping of the left image with  
the one on the right or vice versa) can be reduced  
to deliver a clear quality.  
0
To do so, use the H I keys to move the cursor.  
Setting range: -8 to +8  
0
Press the [MENU] button to exit  
2
29  
         
Selecting an Image Quality According to the  
Video Type  
Setting the Picture Mode  
You can adjust the image quality according to the type of video image you are viewing.  
Press the [PICTURE MODE] button, and use the [JK] keys  
1
to select and set the desired “Picture Mode”  
0
You can also perform the setting by pressing the [MENU] button to display  
the menu followed by selecting “Picture Adjust”"“Picture Mode”.  
MODE 1  
MODE 2  
MODE 3  
0
0
SETTING MEMORY  
You can also press the “Cinema”, “HDR” or “Natural” button to set the Picture  
mode directly.  
ANAMO.  
You can configure more detailed setting items by pressing the [MENU] button  
to display the menu, followed by selecting “Picture Adjust”"“Picture Mode”  
and pressing the [OK] button. (P. 46)  
Item  
Description  
Film*1 M N  
Reproduces faithfully the texture of movie films.  
Cinema*1  
Reproduces the image in vivid colors. Suitable for all  
movies.  
HDR  
Animation*1  
Natural*1  
Suitable for animated works.  
PICTURE  
MODE  
COLOR  
GAMMA  
PROFILE  
SETTINGS  
1
Image quality that focuses on natural color and gradation  
reproduction. Suitable for drama footage, etc.  
C.M.D.  
HDR*2  
Making full use of the wide color gamut and contrast, this  
mode is suited for viewing HDR contents such as Ultra HD  
Blu-ray.  
THX*1 M N  
Image quality certified by THX.  
User 1 to User 5 *3  
Enables user-defined image quality data to be saved and  
retrieved.  
*1 For Picture modes with the *1 mark, the optimal settings for 2D and 3D signals  
are stored separately and applied automatically according to the selected mode.  
0
Edited settings will also be saved separately.  
No changes will be made to the Picture mode name.  
0
*2 If HDR (high dynamic range) signal is detected, the picture mode will  
automatically switch to “HDR”.  
*3 To view videos that support the x.v.Color format, select a user setting (“User 1”  
to “User 5”) in “Picture Mode”, and set “Color Profile” to “x.v.Color”.  
30  
     
Setting the Color Profile  
By setting the “Color Profile” (color space information) according to the “Picture Mode”, you can fine-tune the image  
quality according to the movie you are viewing.  
1
menu  
0
The selectable “Color Profile” settings vary according to the “Picture Mode” and also whether the signal is 2D  
or 3D.  
List of “Color Profile” for “Picture Mode” O  
Picture Mode  
Cinema  
2D Signal Input  
Standard  
Cinema  
3D Signal Input  
Description  
Color space of the HDTV standard. *1  
3D Cinema  
Color space suitable for all movies.  
Color space suitable for all 3D movies.  
Color space suitable for HDR content.  
Color space of the HDTV standard. *1  
Color space that is suitable for animated works.  
Color space suitable for 3D animation works.  
Color space suitable for HDR content.  
Color space of the HDTV standard. *1  
Color space that is suitable for drama footage, etc.  
Color space suitable for 3D broadcasts.  
Color space suitable for HDR content.  
Color space of the HDTV standard. *1  
Color space that is suitable for drama footage, etc.  
Color space suitable for HDR content.  
Color space of the HDTV standard. *1  
Color space suitable for all movies.  
HDR  
Animation  
Natural  
HDR  
Standard  
Animation  
3D Animation  
HDR  
Standard  
Video  
3D Video  
HDR  
Standard  
Video  
HDR  
User 1 to User 5 Standard  
Cinema  
Animation  
Video  
Color space that is suitable for animated works.  
Color space that is suitable for drama footage, etc.  
Color space suitable for HDR content.  
Disables color space adjustment.  
HDR  
Off  
3D Cinema  
3D Animation  
3D Video  
Color space suitable for all 3D movies.  
Color space suitable for 3D animation works.  
Color space suitable for 3D broadcasts.  
Color space that is close to that of the x.v.Color standard.  
Saves the auto calibration values.  
x.v.Color*2*3  
Custom1 to Custom5  
0
To perform auto calibration, you need to get ready a commercially  
available optical sensor and the projector calibration software  
program. For more details, please refer to our website.  
*1 HDTV is the abbreviation for High Definition Television.  
*2 To view videos that support the x.v.Color format, select a user setting (“User 1” to “User 5”) in “Picture Mode”,  
and set “Color Profile” to “x.v.Color”.  
*3 x.v.Color is a wide color space standard for used in videos; it includes wider color gamut than the HDTV standard.  
31  
   
List of “Color Profile” for “Picture Mode” M N  
Picture Mode  
Film  
2D Signal Input  
Film 1  
3D Signal Input  
Description  
Color space that is close to the characteristics of Eastman Kodak Company movie films.  
Color space that is close to the characteristics of FUJIFILM Corporation movie films.  
Color space suitable for digitally remastered piece of art based on a Technicolor film.  
Color space suitable for 3D movies recorded in film.  
Film 2  
Film 3  
3D Film*1  
Cinema  
Standard  
Cinema 1  
Color space of the HDTV standard. *2  
Original JVC cinema-specific color gamut that achieves a balance between increased  
brightness and color vividness.  
3D Cinema  
Cinema 2  
Color space that is close to that of the DCI standard.  
Color space suitable for all 3D movies.  
Color space suitable for HDR content.  
Color space that is suitable for BT.2020.  
Color space of the HDTV standard. *2  
HDR  
BT.2020  
Standard  
Anime 1  
Animation  
Color space that is suitable for CG animation works. Ideal for animated works with bright  
colors.  
Anime 2  
Color space that is suitable for cel animation works. Ideal for animated works with light  
colors.  
HDR  
3D Animation  
Color space suitable for 3D animation works.  
Color space suitable for HDR content.  
BT.2020  
Standard  
Video  
Color space that is suitable for BT.2020.  
Natural  
Color space of the HDTV standard. *2  
Color space that is suitable for drama footage, etc. making use of the increased brightness.  
Color space suitable for 3D video materials.  
Color space that faithfully reproduces the video as it is.  
Color space suitable for HDR content.  
3D Video  
Reference  
HDR  
BT.2020  
Standard  
Video  
Color space that is suitable for BT.2020.  
HDR  
THX  
Color space of the HDTV standard. *2  
Color space that is suitable for drama footage, etc. making use of the increased brightness.  
Color space suitable for HDR content.  
HDR  
BT.2020  
THX*3  
Color space that is suitable for BT.2020.  
Color space of the THX standard.  
3D THX*3  
32  
Picture Mode  
2D Signal Input  
3D Signal Input  
Description  
User 1 to User 5 Standard  
Cinema 1  
Color space of the HDTV standard. *2  
Original JVC cinema-specific color gamut that achieves a balance between increased  
brightness and color vividness.  
Cinema 2  
Anime 1  
Color space that is close to that of the DCI standard.  
Color space that is suitable for CG animation works. Ideal for animated works with bright  
colors.  
Anime 2  
Color space that is suitable for cel animation works. Ideal for animated works with light  
colors.  
Video  
Color space that is suitable for drama footage, etc. making use of the increased brightness.  
Color space that faithfully reproduces the video as it is.  
Color space suitable for HDR content.  
Reference  
HDR  
BT.2020  
Off  
Color space that is suitable for BT.2020.  
Disables color space adjustment.  
3D Cinema  
3D Animation  
3D Video  
x.v.Color*4*5  
Color space suitable for all 3D movies.  
Color space suitable for 3D animation works.  
Color space suitable for 3D video materials.  
Color space of the x.v.Color standard.  
Custom1 to Custom5  
Saves the auto calibration values.  
0
To perform auto calibration, you need to get ready a commercially available optical  
sensor and the projector calibration software program. For more details, please refer  
to our website.  
*1 The value is fixed during 3D signal input, and selection cannot be made.  
*2 HDTV is the abbreviation for High Definition Television.  
*3 Color Profile is fixed when “THX” is selected as the “Picture Mode”.  
*4 To view videos that support the x.v.Color format, select a user setting (“User 1” to “User 5”) in “Picture Mode”,  
and set “Color Profile” to “x.v.Color”.  
*5 x.v.Color is a wide color space standard for used in videos; it includes wider color gamut than the HDTV standard.  
Adjusting to the Preferred Color (Color Management)  
Based on the setting of the selected “Color Profile”, you can adjust each of the following colors according to your  
preference: Red, Yellow, Green, Cyan, Blue, and Magenta.  
1
2
Press the [ADVANCED MENU] button to display the “Color Profile” menu  
Picture Adjust  
Set “Color Management” to “On”, and press the [OK]  
> Color Profile  
Color Profile  
Film 1  
button  
Color Management  
Color Selection  
Axis Position  
Hue  
Saturation  
Brightness  
On  
Red  
Off  
On  
0
You can also perform setting from “Picture Adjust”"“Color Profile”"“Color  
0
0
0
0
Management” in the menu.  
Before  
Reset  
Operate  
Exit  
Back  
BACK  
MENU  
Select  
3
Adjust to the preferred color  
33  
 
A
B
Select “Color Selection”, and press the H I keys to  
Adjustable range when  
Red is selected: 30°  
with Red as the center  
Axis Position (Image)  
select the color to adjust  
0
For color adjustment, select the color from the  
following: “Red”, “Yellow”, “Green”, “Cyan”, “Blue”,  
“Magenta”.  
Green  
Yellow  
Counterclockwise rotation: +  
Clockwise rotation: -  
Red  
Adjust the selected color  
Cyan  
Item  
Setting Range  
Description  
Axis Position -30 to 30  
Fine-tune the position  
of the central axis of  
the selected color.  
Blue  
Magenta  
Hue  
-30 to 30  
-30 to 30  
Adjusts the hue (color  
tone).  
Picture Adjust  
Saturation  
Adjusts the color  
saturation (vividness).  
-30 (dull) to +30 (vivid)  
> Color Profile  
Color Profile  
Film 1  
Color Management  
On  
Red  
Brightness  
-30 to 30  
Adjusts the  
brightness.  
-30 (dark) to +30  
(bright)  
Color Selection  
Axis Position  
Hue  
Saturation  
Brightness  
A
B
0
0
0
0
0
Selecting “Reset” resets all the adjustment data.  
0
Pressing the [HIDE] button on the remote control  
Before  
Exit  
Reset  
Operate  
enables you to check the image before  
adjustment. Press the [HIDE] button again to  
return to the adjustment screen.  
Back  
MENU  
BACK  
Select  
4
Press the [MENU] button to exit  
34  
Adjusting Movies for Increased  
Expressiveness (Multiple Pixel Control)  
The new image-processing algorithm developed by JVC  
0
Images are displayed in the original resolution (2K)  
helps to create a natural impression that is sharper at  
when “4K e-shift” is set to “Off”.  
areas in focus, and softer at areas that are not in focus,  
enabling you to enjoy highly expressive 4K images with  
a greater sense of depth.  
0
“4K e-shift” is fixed at “On” during 4K signal input.  
“Graphic Mode”, “Smoothing” and “NR” are grayed out  
during 4K 50/60p signal input.  
0
0
“4K e-shift” is fixed at “Off” during 3D signal input.  
Press the [MPC] button to display the  
1
adjustment menu  
3
Press the [MENU] button to exit  
0
You can also perform setting from “Picture  
Adjust”"“MPC Level” in the menu.  
Toggling between the States before  
and during Adjustment  
Pressing the [HIDE] button on the remote control enables  
you to toggle between the states before adjustment and  
during adjustment.  
Picture Adjust  
>> MPC Level  
4K e-shift  
Graphic Mode  
On  
2K  
0
0
0
Enhance  
Smoothing  
NR  
Before  
HIDE  
Reset  
Operate  
Exit  
Back  
BACK  
MENU  
Select  
.
Make adjustments according to your  
preference based on the setting of the  
selected “Picture Mode”  
2
* The factory setting varies with the “Picture  
Mode”.  
Item  
Setting  
Description  
4K e-shift On (4K)/Off Switches the display  
(2K)  
resolution.  
Graphic  
Mode  
4K/2K  
Select whether the content  
you are viewing is of high  
sharpness such as graphics.  
It is recommended to set to  
“4K” when viewing content  
mastered in 4K.  
Enhance* 0 to 10  
Smoothing 0 to 10  
Enhances the sharpness of  
the image.  
Increase/decrease  
background detail.  
NR  
0 to 10  
Reduces the noise of the  
video image.  
* In the case of 4K 50/60p and other input signals, the  
respective setting values are saved.  
35  
   
Fine-tuning the Image Quality  
Adjusting the Output Value of the Projected Image (Gamma)  
You can adjust the output value of the projected image with respect to the video signal input.  
Example of gamma adjustment  
The overall image appear brighter with respect to the original image, making the dark areas more visible.  
A
B
255  
0
B
A
0
255  
Input Value  
The photos are for illustrative purposes onl
y
.  
.
Increases the contrast with respect to the original image, creating a greater sense of depth.  
A
B
255  
B
A
0
0
255  
Input Value  
The photos are for illustrative purposes onl
y
.  
.
HDR  
Press the [GAMMA] button  
1
PICTURE  
MODE  
COLOR  
GAMMA  
PROFILE  
SETTINGS  
GAMMA  
C.M.D.  
0
Pressing the [GAMMA] button each time switches the setting in sequence.  
You can also perform the setting by pressing the [MENU] button to display  
0
the menu followed by selecting “Picture Adjust”"“Gamma”.  
* The setting value varies with the model in use, as well as the “Picture Mode”.  
Gamma Settings for Different “Picture Mode” O  
Picture Mode  
Selectable Settings  
Description  
Cinema  
Normal  
A
Recommended setting for normal viewing.  
Animation  
Natural  
Places more emphasis on the gradation compared to the  
Normal setting.  
HDR  
User 1 to User 5  
B
C
Places more emphasis on the contrast compared to the  
Normal setting.  
Places more emphasis on the brightness compared to the  
Normal setting.  
HDR(ST.2084)  
HDR(Hybrid Log)  
Custom 1 to Custom 3  
Suited for viewing HDR content such as UHD BD (HDR10).  
Suited for viewing HDR content such as HDR broadcast.  
Enables fine adjustment of gamma according to  
preference.  
* When “Color Profile” is set to “x.v.Color”, the setting is fixed at “Normal”.  
36  
     
Gamma Settings for Different “Picture Mode” M N  
Picture Mode  
Film  
Selectable Settings  
Description  
When “Color Profile” is Film 1  
Image is close to the characteristics of Eastman Kodak  
set to “Film 1”  
Company movie films.  
Film 2  
Places more emphasis on the gradation compared to the  
“Film 1” setting.  
When “Color Profile” is Film 1  
set to “Film 2”  
Places more emphasis on the contrast compared to the  
“Film 2” setting.  
Film 2  
Image is close to the characteristics of FUJIFILM  
Corporation movie films.  
When “Color Profile” is Film 1  
Places emphasis on the contrast.  
Places emphasis on the gradation.  
Places emphasis on the contrast.  
Places emphasis on the gradation.  
set to “Film 3”  
Film 2  
When “Color Profile” is Film 1  
set to “3D Film”  
Film 2  
Custom 1 to Custom 3  
Enables fine adjustment of gamma according to  
preference.  
Cinema  
Normal  
A
Recommended setting for normal viewing.  
Animation  
Natural  
Places more emphasis on the gradation compared to the  
Normal setting.  
HDR  
User 1 to User 5  
B
C
Places more emphasis on the contrast compared to the  
Normal setting.  
Places more emphasis on the brightness compared to the  
Normal setting.  
HDR(ST.2084)  
HDR(Hybrid Log)  
Custom 1 to Custom 3  
Suited for viewing HDR content such as UHD BD (HDR10).  
Suited for viewing HDR content such as HDR broadcast.  
Fine-tunes the gamma setting according to the user’s  
preference.  
THX  
THX  
Video of the THX standard.  
*1 When “Color Profile” is set to “x.v.Color”, the setting is fixed at “Normal”.  
*2 When “Color Profile” is set to “THX”/“3D THX”, the setting is fixed at “THX”.  
Fine-tuning to the Preferred Gamma Setting  
You can perform fine adjustments based on the selected gamma adjustment setting.  
1 Press the [ADVANCED MENU] button several times to display the gamma menu  
0
You can also perform setting from “Picture Adjust”"“Gamma” in the menu.  
Picture Adjust  
> Gamma  
Gamma  
Custom 1  
Correction Value  
Color Selection  
Picture Tone  
Dark Level  
2.2  
White  
0
0
0
Bright Level  
Reset  
Operate  
Exit  
Back  
BACK  
MENU  
Select  
37  
   
2 Adjust to the preferred setting  
0
Select the color to be adjusted from “Color Selection” and adjust the “Picture Tone”, “Dark Level” and “Bright  
Level”.  
Adjustment item and its setting  
Item  
Description  
Setting  
Color Selection  
For selecting the color for adjusting “Picture Tone”, White / Red / Green / Blue  
“Dark Level” and “Bright Level”.  
Picture Tone  
Adjusts the overall brightness automatically for a  
well-balanced result without compromising the  
gradation of the image.  
-16 (darkens image for an underexposed  
effect) to +16 (brightens image for an  
overexposed effect)  
Dark Level  
Adjusts the dark areas of the input image.  
-7 (darkens the shadows) to +7  
(brightens the shadows)  
0
To do so, use the H I keys to move the cursor.  
Bright Level  
Adjusts the bright areas of the input image.  
-7 (darkens the highlights) to +7  
(brightens the highlights)  
0
To do so, use the H I keys to move the cursor.  
* Adjustment cannot be made when “Color Profile” is set to “x.v.Color”.  
Selecting the Default Value for Making Adjustments  
0
When one of “Custom 1” to “Custom 3” is selected in “Gamma”, you can select a “Correction Value”.  
0
Select the base “Correction Value” for adjustment using the H I keys.  
List of selectable “Correction Value” according to “Picture Mode” O  
Picture Mode  
Correction Value  
Cinema  
Animation  
Natural  
HDR  
1.8  
1.9  
2.0  
2.1  
User 1 to User 5  
2.2  
2.3  
2.4  
2.5  
2.6  
Normal  
A
B
C
HDR(ST.2084)  
HDR(Hybrid Log)  
Import  
38  
   
List of selectable “Correction Value” according to “Picture Mode” M N  
Picture Mode  
Correction Value  
Film  
Film 1  
Film 2  
Import  
Cinema  
Animation  
Natural  
HDR  
1.8  
1.9  
2.0  
2.1  
User 1 to User 5  
2.2  
2.3  
2.4  
2.5  
2.6  
Normal  
A
B
C
HDR(ST.2084)  
HDR(Hybrid Log)  
Import  
When “Correction Value” is set to “Import”  
0
0
Selecting “Import” enables you to select the gamma data created externally. The factory setting for “Import” is the  
same as the “Normal” setting.  
You can use the projector calibration software to customize the gamma data adjustment, and import the created  
gamma data.  
For more details, please refer to our website.  
39  
Gamma Adjustment  
0
0
0
0
When the gamma curve is a straight line:  
The brightness and contrast of the video input will be  
the same as that of the video output.  
Gamma Curve  
A
255  
Bright  
Area for which the gamma curve is above the straight  
line (A):  
Video output appears brighter than the input.  
Area for which the gamma curve is below the straight  
D”  
D
0
line (B):  
Video output appears darker than the input.  
B
Area for which the slope of the gamma curve is steep  
(midtone) (C):  
The grayscale range of the video output becomes  
wider, and the contrast increases (D"D’).  
Dark  
0
255  
C
Dark  
Input Value  
Bright  
Gamma Adjustment When Viewing HDR Contents (Tone Mapping)  
“HDR(ST.2084)” gamma is the PQ curve adopted by HDR10. Fine adjustments can be made according to the screen  
size and environment although the default settings for viewing with the projector have been adjusted to allow optimum  
viewing.  
Default settings when viewing HDR contents of this projector  
Picture Mode  
: HDR  
Gamma  
: HDR(ST.2084)  
Estimated Screen Size  
: 90 to 120 inch (screen gain 1.0)  
Estimated MaxCLL/MaxFALL : MaxCLL 1000 nits, MaxFALL 400 nits  
Picture tone adjustment method  
0
Picture Tone  
.
When Picture Tone is set to “-”  
When Picture Tone is set to “+”  
(The entire screen becomes dark.)  
(The entire screen becomes brighter.)  
0
0
Screen size is smaller than estimated  
Screen size is bigger than estimated  
0
0
MaxFALL/MaxCLL value is higher than  
MaxFALL/MaxCLL value is lower than  
.
estimated (P. 59)  
0
0
Screen becomes brighter in the course of  
Screen becomes darker in the course of  
viewing  
viewing  
Bright/dark area adjustment method  
0
Dark Level  
.
(+) To make the dark area information more  
visible  
(―) To enhance the contrast  
.
0
Bright Level  
.
(―) To enhance the gradation of highlight areas  
(+) To enhance the contrast  
.
40  
Reducing the After-image of Fast-moving Images (Blur Reduction)  
Low Latency  
For changing the low latency setting.  
You are recommended to set to “On” for content requiring split-second timing with the operation screen of PC signals  
or games.  
Press the [MENU] button to display the menu and select “Picture Adjust”"“Blur  
Reduction”"“Low Latency”  
1
Setting  
Description  
On  
Off  
Performs the low latency setting.  
Does not perform the low latency setting.  
0
If “Keystone” is set to other than “0”, the “Low Latency” is set to “Off” and grayed out.  
If “Anamorphic” is set to other than “Off”, the “Low Latency” is set to “Off” and grayed out.  
0
* “Clear Motion Drive” cannot be set when “Low Latency” is set to “On”.  
Low Latency Mode  
High bandwidth signals such as 4K 10-bit and 12-bit signals can be processed without being converted. This allows a  
video to be shown without losing its original quality, thereby enabling the enjoyment of contents such as movies and  
concerts at higher quality.  
41  
 
Clear Motion Drive (C.M.D.)  
Optimal interpolation according to the content is made possible with the new high-definition image interpolation  
technique that supports 3D images.  
For some scenes, interpolation may cause distortion in the image. In this case, set to “Off”.  
Original Image  
Interpolation Enabled  
Intermediate Frame Generation  
Intermediate Frame Generation  
.
HDR  
1 Press the [C.M.D.] button  
PICTURE  
MODE  
COLOR  
GAMMA  
PROFILE  
SETTINGS  
C.M.D.  
0
Pressing the [C.M.D.] button each time switches the mode in the following  
sequence: “Off”"“Low”"“High”"“Inverse Telecine”"“Off”...  
Setting  
Description  
Interpolation is not performed.  
Off  
Low  
High  
Improves motion lag for movie type images.  
Improves motion lag fast moving sports type images.  
Inverse Telecine  
60i/60p video images such as those of TVs and DVDs.  
Suitable for original images that are 24-frame film sources.  
0
Does not function for 24p video images.  
* C.M.D. is the abbreviation for Clear Motion Drive.  
* This item cannot be set when “Low Latency” is set to “On”.  
Motion Enhance  
Optimal image quality with reduced image blurring is made possible by enhancing the responsiveness of the liquid  
crystal device.  
If the image outline is unnatural, set this item to “Off”.  
Press the [MENU] button to display the menu and select “Picture Adjust”"“Blur  
Reduction”"“Motion Enhance”  
1
Setting  
Description  
Off  
Low  
High  
Does not perform correction.  
Reduces image blurring.  
Further reduces image blurring than “Low”.  
42  
 
Viewing High Contrast Images (Lens Aperture)  
JVC has developed an image analysis algorithm, which analyzes the state of the video image in real time, and controls  
the aperture dynamically according to the image information.  
This technology enables viewers to enjoy video images with enhanced contrast.  
1
Press the [LENS AP.] button  
Pressing the [LENS AP.] button each time switches the setting in sequence.  
MODE  
1
MODE  
2
MODE  
3
Setting  
Description  
SETTING MEMORY  
Auto 1  
Auto 2  
Manual  
Image contrast is enhanced.  
ANAMO.  
Places emphasis on the gradation.  
Does not perform dynamic control.  
Select this setting to perform adjustment manually.  
*1 Manual adjustment is disabled in the “Auto 1” and “Auto 2” setting.  
To perform adjustment manually, select “Manual”.  
*2 When the setting is changed to Auto after performing manual adjustment, the  
value set manually will be used as the aperture value for Auto.  
43  
   
Adjustments and Settings in the Menu  
Pressing the [MENU] button displays the menu.  
Press the [JKH I] keys to select an item, followed by pressing the [OK] button to confirm the selection.  
List of Menu Items  
Picture Adjust  
I Picture Mode ................................................................................................................................................... P. 30  
9 Clear Black ................................................................................................................................................. P. 46  
9 Lamp Power ............................................................................................................................................... P. 46  
9 Lens Aperture ............................................................................................................................................. P. 46  
9 User Name Edit .......................................................................................................................................... P. 46  
I Color Profile ..................................................................................................................................................... P. 31  
Color Management ......................................................................................................................................... P. 33  
I Color Temp. ..................................................................................................................................................... P. 47  
I Gamma ............................................................................................................................................................ P. 36  
9 Picture Tone ............................................................................................................................................... P. 38  
9 Dark Level / Bright Level ............................................................................................................................. P. 38  
I MPC Level ....................................................................................................................................................... P. 35  
I Blur Reduction ................................................................................................................................................. P. 41  
I Contrast ........................................................................................................................................................... P. 48  
I Brightness ....................................................................................................................................................... P. 48  
I Color ................................................................................................................................................................ P. 49  
I Tint .................................................................................................................................................................. P. 49  
Input Signal  
I Input Level ....................................................................................................................................................... P. 49  
I Color Space ..................................................................................................................................................... P. 49  
I Aspect ............................................................................................................................................................. P. 50  
I Progressive ...................................................................................................................................................... P. 50  
I Mask ................................................................................................................................................................ P. 50  
I 3D Setting ........................................................................................................................................................ P. 28  
I Picture Position ................................................................................................................................................ P. 50  
IHDMI2 EDID ..................................................................................................................................................... P. 50  
44  
       
Installation  
I Lens Control .................................................................................................................................................... P. 23  
9 Focus ......................................................................................................................................................... P. 23  
9 Zoom .......................................................................................................................................................... P. 23  
9 Shift ............................................................................................................................................................ P. 23  
9 Image Pattern ............................................................................................................................................. P. 51  
9 Lock ........................................................................................................................................................... P. 51  
9 Lens Memory Select ................................................................................................................................... P. 25  
9 Lens Memory Save .................................................................................................................................... P. 24  
9 Lens Memory Name Edit ............................................................................................................................ P. 25  
9 Lens Center ................................................................................................................................................ P. 51  
9 Lens Cover M N .......................................................................................................................... P. 51  
I Pixel Adjust ...................................................................................................................................................... P. 52  
I Installation Style ............................................................................................................................................... P. 53  
I Keystone ......................................................................................................................................................... P. 53  
I Anamorphic ..................................................................................................................................................... P. 53  
I High Altitude Mode .......................................................................................................................................... P. 53  
I Screen Adjust .................................................................................................................................................. P. 26  
Display Setup  
I Back Color ....................................................................................................................................................... P. 57  
I Menu Position .................................................................................................................................................. P. 57  
I Signal Display .................................................................................................................................................. P. 57  
I Logo ................................................................................................................................................................ P. 57  
I Language ........................................................................................................................................................ P. 57  
Function  
I Trigger ............................................................................................................................................................. P. 57  
I Off Timer .......................................................................................................................................................... P. 57  
I ECO Mode ....................................................................................................................................................... P. 58  
I Network ........................................................................................................................................................... P. 58  
I Remote Code .................................................................................................................................................. P. 59  
I Lamp Reset ..................................................................................................................................................... P. 62  
Information  
I Information ....................................................................................................................................................... P. 59  
45  
Picture Adjust  
Picture Mode  
You can adjust the image quality according to the type of video image you are viewing.  
You can configure the following setting items by pressing the [MENU] button to display the menu, followed by selecting  
“Picture Adjust”"“Picture Mode” and pressing the [OK] button.  
Clear Black  
Adjusts the difference in brightness in an image electrically to produce an image with contrast.  
Setting  
Description  
Off  
Does not perform correction.  
Mode with a mild effect.  
Mode with a strong effect.  
Low  
High  
Lamp Power  
The brightness of the lamp can be set to “Low” or “High”.  
0
The factory setting varies with the “Picture Mode”.  
Continuous use at the “High” setting may cause the lamp to darken faster.  
0
Lens Aperture  
JVC has developed an image analysis algorithm, which analyzes the state of the video image in real time, and controls  
the aperture dynamically according to the image information.  
This technology enables viewers to enjoy video images with enhanced contrast.  
0
Stopping down the aperture reduces the brightness and increases the contrast.  
Setting range: -15 (stops down) to 0 (opens up)  
0
User Name Edit  
You can edit the “User 1” to “User 5” names in the Picture mode.  
0
Characters that are usable include alphabets (upper or lower case), numeric characters, and symbols.  
Enter not more than 10 characters.  
0
Picture Adjust  
>>User Name Edit  
Name User 1  
Input Cursor  
A
N
a
B
O
b
C
P
c
D
Q
d
E
R
e
r
F
S
f
G
T
g
t
H
U
h
I
V
i
J
W
j
K
X
k
L
Y
l
M
Z
m
Selection Cursor  
n
o
p
q
s
y
v
w
x
y
z
1
!
:
2
"
;
3
#
|
4
$
~
5
%
(
6
&
)
7
*
8
+
9
-
0
/
,
=
.
?
^
@
<
>
[
]
{
}
\
Clear  
All Clear  
Operate  
OK  
Back  
SPACE  
Exit  
After entry is complete, select  
“OK” and press the [OK] button  
MENU  
BACK  
Select  
.
46  
           
Color Profile  
By setting the “Color Profile” (color space information) according to the “Picture Mode”, you can fine-tune the image  
quality according to the movie you are viewing.  
Color Management  
Each of the colors is adjustable according to the user’s preference.  
Color Temp.  
For setting the color temperature of the video image.  
0
When “Picture Mode” is set to “THX” and when “Color Profile” is set to “x.v.Color”, the setting is fixed at 6500K.  
Preset  
Setting  
Description  
Xenon 1, Xenon 2 M N  
* Selectable when “Picture Mode” is set to  
“Film” or “Cinema”.  
Color temperature that reproduces the characteristics of a xenon lamp  
used in cinemas.  
0
Xenon 1: A light source color that is emitted by a film projector  
Xenon 2: A light source color emitted by a projector used for digital  
0
cinema  
5500K, 6500K, 7500K, 9300K  
Custom 1, Custom 2  
Increasing the value enhances the blue tone of the video image, while  
decreasing the value enhances the red tone.  
The color temperature of video images can be adjusted manually and  
saved as one of the three customized settings.  
HDR  
Color temperature suitable for viewing HDR content.  
Color temperature that gives priority to brightness.  
High Bright  
Custom  
Setting  
Description  
Gain Red, Gain Green, Gain Blue  
Adjusts each color in the bright parts of the video image.  
0
Setting range: -255 (reduces the red/green/blue tone) to 0  
(enhances the red/green/blue tone)  
Offset Red, Offset Green, Offset Blue  
Adjusts each color in the dark areas of the video image.  
0
Setting range: -50 (reduces the red/green/blue tone) to +50  
(enhances the red/green/blue tone)  
Gamma  
You can adjust the output value of the projected image with respect to the video signal input.  
Picture Tone  
Adjusts the overall brightness automatically for a well-balanced result without compromising the gradation of the image.  
Dark Level / Bright Level  
You can adjust the image quality to produce a sharp contrast in the brightness.  
47  
   
MPC Level  
You can enjoy natural, expressive 4K images with a stronger sense of depth.  
4K e-shift  
Switches the display resolution.  
0
Setting values: On (4K), Off (2K)  
Graphic Mode  
For selecting whether the content you are viewing is of high sharpness such as graphics.  
It is recommended to set to “4K” when viewing content mastered in 4K.  
0
Setting values: 4K, 2K  
Enhance  
For adjusting the high-frequency areas. Increasing the value enhances the definition for a sharper image quality.  
0
Setting range: 0 to 10  
* In the case of 4K 50/60p and other input signals, the respective setting values are saved.  
Smoothing  
For adjusting the low-frequency areas. Increasing the value enhances the blurriness of the image for a softer effect.  
0
Setting range: 0 to 10  
NR  
Prevents noise from becoming too pronounced.  
0
Setting range: 0 (weak) to 10 (strong)  
MEMO  
0
“4K e-shift” is fixed at “On” during 4K signal input.  
0
“Graphic Mode”, “Smoothing” and “NR” are grayed out during 4K 50/60p signal input.  
“4K e-shift” is fixed at “Off” during 3D signal input.  
0
Blur Reduction  
For reducing the after-image, which occurs in a fast-moving scene.  
Contrast  
For adjusting the difference in brightness to produce an image with contrast.  
0
Setting range: -50 (little difference in brightness) to +50 (large difference in brightness)  
* Adjustment cannot be made when “Color Profile” is set to “x.v.Color”.  
Brightness  
For adjusting the brightness of the video image.  
0
Setting range: -50 (darker) to +50 (brighter)  
* Adjustment cannot be made when “Color Profile” is set to “x.v.Color”.  
48  
     
Color  
For adjusting the color density of the video image.  
0
Setting range: -50 (lighter) to +50 (deeper)  
* Adjustment cannot be made when “Color Profile” is set to “x.v.Color”.  
Tint  
For adjusting the hue of the video image.  
0
Setting range: -50 (reddish) to +50 (greenish)  
* Adjustment cannot be made when “Color Profile” is set to “x.v.Color”.  
Input Signal  
Input Level  
For setting the dynamic range (gradation) of the video input.  
If the image is not displayed properly even after selecting “Auto”, select an appropriate setting.  
0
If the dynamic range is not appropriate, the bright areas become overexposed, and the dark areas become  
underexposed.  
Setting  
Description  
Sets the input signal level automatically.  
Auto  
Standard  
Enhanced  
Super White  
Select this setting if you are inputting video signals (dynamic range: 16 - 235).  
Select this setting if you are inputting PC signals (dynamic range: 0 - 255).  
Select this setting when inputting Super White-compatible device signals (dynamic  
range: 16 - 255).  
Color Space  
For setting the color space of the input signal.  
If the image is not displayed properly even after selecting “Auto”, select an appropriate setting.  
Setting  
Description  
Auto  
Detects “YCbCr (4:4:4)”, “YCbCr (4:2:2)”, and “RGB” automatically.  
Select this setting when inputting YCbCr (4:4:4) video signals.  
Select this setting when inputting YCbCr (4:2:2) video signals.  
Select this setting when inputting RGB video signals.  
YCbCr (4:4:4)  
YCbCr (4:2:2)  
RGB  
49  
         
Aspect  
The screen size of the projected image can be adjusted optimally according to the original screen size (aspect) that  
has been input.  
Progressive  
For setting the interpolation method for the interlaced signals. If the image outline is unnatural, set this item to “Off”.  
Setting  
Description  
Auto  
Performs interpolation by automatically detecting whether the interlaced signals  
are converted from 24p video images, such as those in film movies, or interlaced  
signals of video materials.  
Off  
Interpolates video images as interlaced signals of video materials, etc.  
Mask  
For hiding the peripheral area of the image with a mask (black strip).  
Off  
Setting  
Description  
Off  
Not masked.  
Custom 1 to Custom 3  
Masks about 0 to 220 pixels of the four sides of the  
image.  
* The pixel count is 1920 pixels in the horizontal  
direction and 1080 pixels in the vertical direction.  
On  
Mask: black strip around the periphery  
3D Setting  
For setting 3D movies for viewing.  
Picture Position (Horiz./Vert.)  
Adjust the position if the edges of the image are partially missing due to the timing of horizontal and vertical  
synchronization signals.  
* Adjustment cannot be made during 4K, 3D and 1080i signal input.  
HDMI2 EDID  
For changing the EDID mode of the [HDMI 2] terminal. Set to “A” under normal condition.  
Images with resolution 1920x1080 or lower may not be displayed when some old devices are used.  
In that case, connect to the [HDMI 2] terminal and set “HDMI2 EDID” to “B”.  
* EDID (Extended Display Identification Data) refers to the information, such as supported resolutions, exchanged  
between devices.  
50  
           
Installation  
Lens Control  
Focus / Zoom / Shift  
For adjusting the lens according to the projection position  
Image Pattern  
Setting  
Description  
Displays the lens adjustment pattern.  
On  
Off  
Displays external signals, and does not display the lens adjustment pattern.  
Lock  
Setting  
Description  
On  
Locks the lens to prevent any erroneous operation on the adjustments.  
0
When “On” is selected, all lens control functions other than “Lens Memory  
Select” cannot be operated.  
Does not lock the lens.  
Off  
Lens Memory Select / Lens Memory Save / Lens Memory Name Edit  
The Focus, Zoom, and Shift settings can be saved or retrieved, so you can switch easily to a different aspect ratio  
(screen size) according to the image.  
Lens Center  
Returns the lens position to the center.  
Lens Cover M N  
Setting  
Description  
Auto  
Opens/closes the lens cover according to the power on/off operation.  
Leaves the lens cover open regardless of the power on/off mode.  
Open  
51  
           
Pixel Adjust  
Adjust  
For setting the adjustment feature to On (Memory 1 or Memory 2) or Off.  
* You can save the settings separately when an anamorphic lens is used and when you are using the projector with  
a screen.  
Adjust Area  
Setting  
Description  
Whole  
Zone  
Adjusts the entire image.  
Enables fine adjustment of each zone by dividing the screen into 11 vertical x 11  
horizontal zones.  
Adjust Color  
For selecting the color to adjust (“Red” or “Blue”).  
Adjust Pattern Color  
For setting the color of the adjustment pattern displayed during adjustment to “White” or “Yellow / Cyan”.  
Adjust (Pixel)  
When “Adjust Area” is set to “Whole”, adjustment can be made by moving in units of one pixel on the screen of the color  
selected in “Adjust Color”.  
0
Adjustment cannot be made when “Adjust Area” is set to “Zone”.  
Setting  
H (Horizontal)  
Description  
Setting range: -2 (moves red/blue to the left) to +2 (moves red/blue to the right)  
Setting range: -2 (moves red/blue downward) to +2 (moves red/blue upward)  
V (Vertical)  
Adjust (Fine)  
When “Adjust Area” is set to “Whole”, adjustment can be made by moving in units of 1/16 pixel on the screen of the  
color selected in “Adjust Color”.  
When “Adjust Area” is set to “Zone”, the screen is divided into 11 vertical x 11 horizontal zones, and fine adjustment of  
each zone is possible.  
Setting  
H (Horizontal)  
Description  
Setting range: -31 (moves red/blue to the left) to +31 (moves red/blue to the right)  
Setting range: -31 (moves red/blue downward) to +31 (moves red/blue upward)  
V (Vertical)  
Reset  
Restores all pixel adjustment data to the factory default.  
52  
 
Installation Style  
For setting to “Front”, “Ceiling Mount (F)”, “Rear”, or “Ceiling Mount (R)” according to the installation status of the  
projector.  
0
“Front” or “Ceiling Mount (F)” is set when projector is installed in the front with respect to the screen.  
“Rear” or “Ceiling Mount (R)” is set when projector is installed in the rear with respect to the screen.  
0
Keystone  
For correcting any keystone distortion that occurs when the projector is installed at an angle with respect to the screen.  
0
Vertical setting range: -16 to +16  
*1 Increasing the value changes the aspect slightly.  
*2 Adjustment cannot be made during 4K 50/60p signal input.  
Anamorphic  
Configure this setting when an anamorphic lens is used.  
Setting  
Description  
A
Projects the 2.35:1 image with it stretched in the vertical direction only.  
Projects the 16:9 image with it compressed in the horizontal direction only.  
Projects image without any scaling.  
B
Off  
High Altitude Mode  
Set to “On” when using the projector at a location of low atmospheric pressure (higher than 900 m (3,000 ft) above sea  
level).  
Screen Adjust  
performed to reproduce natural images with balanced colors.  
Æ “Setting Screen Correction” (P. 26)  
53  
       
Whole Adjust (Pixel) Operation Procedure  
For making general adjustments to slight color fringing in the horizontal/vertical directions of the video image.  
A
Set “Adjust Area” to “Whole”  
B
Select “Adjust Color” and “Adjust Pattern Color”  
C
Select “Adjust (Pixel)”, and press the [OK] button  
0
The Adjustment mode is activated, and the selected adjustment pattern and Adjustment (Pixel) window are  
displayed.  
Adjustment Pattern  
Pixel Adjust  
Adjustment (Pixel) Window  
Whole Adjust (Pixel)  
Red  
H
V
0
0
Select  
Back  
Color A.  
GAMMA  
Adjust. Color P. A. Area  
COLOR  
TEMP  
3D  
PIC.  
Operate  
BACK  
FORMAT  
ADJ.  
H (Horizontal)  
.
D
E
Press the [OK] button to enter the Adjustment mode  
Use the [JKH I] keys to move and adjust the vertical and horizontal pixels of the entire zone  
0
The adjustment setting appears at the center of the Adjustment (Pixel) window.  
Pixel Adjust  
Color for  
Whole Adjust (Pixel)  
Red  
Pixel Adjustment Setting  
Adjustment  
H 0  
V 0  
Select  
Back  
Color A. Adjust. Color P. A. Area  
Remote Control Operation  
Guide  
COLOR  
TEMP  
3D  
PIC.  
GAMMA  
Operate  
BACK  
FORMAT  
ADJ.  
.
F
After adjustment is complete, press the [BACK] button twice to exit the Adjustment mode  
Remote Control Operation Guide  
Button Name  
Description of Operation  
[GAMMA]  
Changes “Adjust Color”.  
[COLOR TEMP.]  
Switches between “Adjust (Pixel)” and “Adjust (Fine)”.  
0
Switches to “Adjust (Pixel)” when “Adjust Area” is set to “Zone”.  
[3D FORMAT]  
[PIC ADJ.]  
Changes “Adjust Pattern Color”.  
Switches “Adjust Area”.  
0
A zone cursor appears on the adjustment pattern when the “Zone” setting is selected.  
54  
 
Whole Adjust (Fine) Operation Procedure  
For making general adjustments on the misalignment of the entire screen using “Adjust (Pixel)”, followed by making  
fine adjustments.  
A
Set “Adjust Area” to “Whole”  
B
Select “Adjust Color” and “Adjust Pattern Color”  
C
Select Adjust (Fine), and press the [OK] button  
0
The Adjustment mode is activated, and the selected adjustment pattern and Fine window are displayed.  
The adjustable range may be smaller depending on the pixels being adjusted on the entire screen.  
0
Adjustment Pattern  
Pixel Adjust  
Whole Adjust (Fine)  
Fine Window  
Red  
0
0
( 0  
( 0  
/
/
0 )  
0 )  
H
V
Select  
Back  
Color A.  
GAMMA  
Adjust. Color P. A. Area  
COLOR  
TEMP  
3D  
PIC.  
Operate  
BACK  
FORMAT  
ADJ.  
H (Horizontal)  
.
D
E
Press the [OK] button to enter the Adjustment mode  
Use the [JKH I] keys to move and adjust the vertical and horizontal pixels of the entire zone  
0
The adjustment setting appears at the center of the Fine window.  
Pixel Adjust  
Whole Adjust (Fine)  
Color for  
Red  
Pixel Adjustment Setting  
Adjustment  
0 ( 0 / 0 )  
H
V
0 ( 0 / 0 )  
Select  
Back  
Color A. Adjust. Color P. A. Area  
Remote Control Operation  
Guide  
COLOR  
TEMP  
3D  
PIC.  
Operate  
GAMMA  
BACK  
FORMAT  
ADJ.  
Adjustment Setting  
H 20 20 / 20)  
5 5 / 5)  
V
Indicates the maximum and  
minimum misalignment value of  
the entire screen.(Max. / Min.)  
.
F
After adjustment is complete, press the [BACK] button twice to exit the Adjustment mode  
MEMO  
0
0
If both the maximum overall screen misalignment of H (horizontal direction) and V (vertical direction) are “31”, you  
cannot select a value that is larger than the displayed setting even when the adjustment setting is lower than the  
maximum value.  
If the minimum overall screen misalignment is “-31”, you cannot select a value that is smaller than the displayed  
setting even when the adjustment setting is higher than the minimum value.  
55  
 
Zone Adjust Operation Procedure  
For fine-tuning misalignments on a part of the screen after adjusting the overall screen misalignment using “Adjust  
(Pixel)” and “Adjust (Fine)”.  
0
The screen can be divided vertically and horizontally into 10 sections for partial adjustments to be made.  
A
Set “Adjust Area” to “Zone”  
B
Select “Adjust Color” and “Adjust Pattern Color”  
C
Select Adjust (Fine), and press the [OK] button  
0
The Adjustment mode is activated, and the selected adjustment pattern and Zone Adjustment window are  
displayed.  
0
The adjustable range may be smaller depending on the pixels being adjusted on the entire screen.  
Adjustment Pattern  
Zone Cursor  
Pixel Adjust  
Zone Adjustment Window  
Zone Adjust  
Red  
Position  
0
/
0
H
0
0
V
Select  
Back  
Color A. Adjust. Color P. A. Area  
COLOR  
TEMP  
3D  
PIC.  
GAMMA  
Operate  
BACK  
FORMAT  
ADJ.  
H (Horizontal)  
.
D
E
F
Press the [JKH I] keys to move the cursor to the point to be adjusted  
Press the [OK] button to enter the Adjustment mode  
Use the [JKH I] keys to move and adjust the vertical and horizontal pixels of the entire zone  
0
The adjustment setting appears at the center of the Zone Adjustment window.  
Pixel Adjust  
Color for  
Red  
Zone Adjust  
Pixel Adjustment Setting  
Adjustment  
Position  
0 / 0  
0
H
V 0  
Select  
Back  
Color A. Adjust. Color P. A. Area  
COLOR  
TEMP  
3D  
PIC.  
Remote Control Operation  
Guide  
GAMMA  
Operate  
BACK  
FORMAT  
ADJ.  
Cursor Position  
8 / 5  
Position  
H 31  
V   7  
Adjustment Setting  
After adjustment is complete, press the [BACK] button twice to exit the Adjustment mode  
.
G
56  
 
Display Setup  
Back Color  
For setting the color of the background to “Blue” or “Black” when there is no signal input.  
Menu Position  
For setting the display position of the menu.  
Signal Display  
Setting  
Description  
Shows the input terminal for 5 seconds when input is switched.  
Not displayed.  
On  
Off  
Logo  
Setting  
Description  
Displays the “D-ILA” logo for 5 seconds during startup.  
Not displayed.  
On  
Off  
Language  
For setting the display language to “日本語”, “English”, “Deutsch”, “Español”, “Italiano”, “Français”, “Português”,  
“Nederlands”, “Svenska”, “Norsk”, “Русский”, “中文”, or “繁體中文”.  
Function  
Trigger  
For setting whether to supply a 12 V output to devices such as an external screen equipped with a trigger function.  
Setting  
Description  
Off  
No output.  
On (Power)  
Outputs control signals (12 V) from the trigger terminal when the power is turned  
on.  
0
When the power is turned off, the control signal output is stopped when the  
cooling function starts.  
On (Anamo)  
Outputs control signals when the “Anamorphic” setting is switched from “Off” to “A”  
or “B”.  
Off Timer  
For setting the duration before the power turns off automatically when the projector is not operated.  
0
Setting values: “Off”, “1 Hour”, “2 Hours”, “3 Hours” and “4 Hours”  
57  
                 
ECO Mode  
Setting  
Description  
On  
Enables “ECO Mode” to minimize power consumption in the Standby mode.  
0
RS-232C / LAN communication cannot be used in the Standby mode.  
If there is no signal transmission and operation for 20 minutes while an image  
0
is projected, the power management switches the equipment automatically into  
standby mode.  
Off  
Select this option to control via RS-232C / LAN communication in the Standby  
mode or if Control4 is to be used.  
Network  
For specifying the settings for external control from a PC or smartphone.  
Setting  
DHCP Client  
Setting  
On  
Description  
Obtains the IP address automatically from the DHCP server inside the connected  
network.  
Off  
For configuring the network settings manually.  
For configuring the IP address.  
IP Address  
Subnet Mask  
Default Gateway  
MAC Address  
Set  
For configuring the subnet mask.  
For configuring the default gateway.  
Displays the MAC address of the unit.  
Applies the network settings.  
Control4  
Set to “On” to allow Control4 SDDP to detect this unit.  
When this unit is not connected to an environment under the control of the controller  
and Control4 SDDP from the Control4 Corporation, set this to “Off”.  
Glossary of Network Terminology  
DHCP  
: Abbreviation for Dynamic Host Configuration Protocol. This is a protocol for the network  
to assign an IP address automatically to the connected device.  
IP Address  
Subnet Mask  
: Numeric characters for identifying the device that is connected to the network.  
: Numeric characters that define the bit count used for the network address that is a  
segment of the IP address.  
Default Gateway  
MAC Address  
: Server for communicating beyond the network that is divided by the subnet mask.  
: Abbreviation for Media Access Control address. This is a number that is unique to each  
network adapter. Each of the network adapters is assigned with a unique MAC address.  
58  
   
Remote Code  
For changing the remote control code.  
Setting  
Description  
A
Change the remote control code from “B” to “A”.  
Change the remote control code from “A” to “B”.  
B
0
You need to configure the remote control according to the settings of this unit.  
On the remote control unit, press the [MENU] and [BACK] buttons at the same time for three seconds or longer to  
switch the code.  
0
The backlight of the remote control blinks 3 times: change the remote control code to “A”  
0
The backlight of the remote control blinks 2 times: change the remote control code to “B”  
Lamp Reset  
For resetting the lamp time to “0”.  
Information  
Setting  
Description  
Input  
Displays video input terminal.  
Source  
Displays the input source.  
(Displayed only during video signal input)  
Resolution  
Displays the image resolution.  
Displays the horizontal frequency.  
Displays the vertical frequency.  
(Displayed only during PC signal input)  
H Frequency  
(Displayed only during PC signal input)  
V Frequency  
(Displayed only during PC signal input)  
Color Depth  
Color Space  
Displays the color space and color bit depth of the input video signal.  
0
The color bit depth is not displayed when YCbCr (4:2:2) is input.  
The color bit depth is displayed when color bit depth information is received  
0
from the source device.  
Colorimetry  
HDR  
Displays the colorimetry of the input video signal.  
Displays the EOTF information when HDR packet is received.  
Max CLL / Max FALL  
Displays the mastering information of the contents during HDR playback.  
Max CLL: Maximum Content Light Level  
Max FALL: Maximum Frame Average Light Level  
0
The information may not be displayed depending on the player and contents.  
Lamp Time  
Soft Ver.  
Displays the lamp time.  
Displays the firmware version.  
59  
               
Replacing the Lamp  
The lamp is a consumable item. If the image appears dark or the lamp goes out, replace the lamp unit.  
0
When the lamp replacement time approaches, the user is notified with a message displayed on the screen and by  
Lamp Replacement Procedure  
3
Loosen the screws of the lamp unit  
CAUTION  
0
0
0
Loosen the screws with a t screwdriver.  
Do not insert your hands into the lamp compartment.  
This could cause significant deterioration in the  
performance of the equipment, or lead to injury and  
electric shock.  
Do not replace the lamp immediately after the unit has  
been used. Allow a cooling period of at least one hour  
before replacement. The temperature of the lamp is  
still high, and may cause burn injuries.  
0
0
0
Do not subject the lamp unit to shock. Doing so may  
cause lamp blowout.  
Do not use a flammable air duster to clean the internal  
parts of the unit. Doing so may cause fire.  
Use only genuine replacement parts for the lamp unit.  
Also, never attempt to reuse an old lamp unit. This  
may cause the unit to malfunction.  
.
0
0
0
Do not touch the surface of a new lamp. Doing so may  
shorten the lamp life and cause lamp blowout.  
4
Pull out the lamp unit  
When replacing the lamp, be careful not to injure  
yourself as the lamp may be broken.  
When replacing the lamp of a projector suspended  
from the ceiling, work at height is required. This is a  
dangerous operation. Please consult our service  
center.  
0
Hold the lamp unit at the dents at the top and  
bottom, and pull it out.  
Pull out the power plug from the power  
outlet  
1
2
Remove the lamp cover  
0
Remove the screw of the lamp cover with a t  
screwdriver.  
.
.
60  
       
5
Install the new lamp unit  
MEMO  
Usable lamp life  
0
When the lamp is used with “Lamp Power” set to  
“Low”, the lamp life on this unit is approximately 4500  
hours. This is the average usable time and not a  
guaranteed value.  
0
The lamp life may not reach 4500 hours depending on  
the operating conditions.  
When the lamp has reached the end of its usable life,  
deterioration progresses rapidly.  
When the video image appears dark, when the color  
tone looks unnatural, or when the image flickers,  
replace the lamp unit with a new one promptly.  
0
0
.
Purchasing a lamp unit  
Please consult your authorized dealer or nearby service  
center.  
Tighten the screws of the new lamp  
unit  
6
0
Tighten the screws with a t screwdriver.  
0
Lamp unit  
Product no.: PK-L2615U  
* Not suitable for household room illumination.  
* Lamps with a different product number or those for  
other projector models cannot be used.  
Information about the lamp  
An ultra-high pressure mercury lamp with a high internal  
pressure is used in the projector.  
Due to the characteristics of this lamp, it may blow out  
with a loud noise or go out when it is subject to shock or  
after using for a prolonged period of time (the time before  
the lamp blows out or goes out varies considerably with  
each lamp as well as the operating conditions).  
.
After replacing the lamp  
7
Attach the lamp cover  
0
Do not place the removed lamp unit at a place that is  
within reach by children or anywhere near  
inflammable items.  
Dispose used lamp units in the same way as  
fluorescent lamps. Follow the regulations of your local  
community for disposal.  
0
Insert the two tabs at the top and bottom of the  
lamp cover into the unit.  
0
0
Tighten the screws with a t screwdriver.  
.
61  
 
Resetting the Lamp Time  
Reset the lamp time when you have replaced the lamp.  
It provides an estimated timing for lamp replacement  
Resetting the lamp time using the remote  
control  
Resetting the lamp time from the menu  
screen  
Insert the power plug into the power  
outlet  
1
Press the [MENU] button to display  
Make sure that you operate the  
1
the menu  
remote control in the Standby mode  
2
(the power plug is inserted into the  
outlet, but the power is not turned on)  
Select “Function”"“Lamp Reset”  
from the menu  
2
0
Press in the order as shown.  
0
Make sure that you press a button within two  
Function  
Trigger  
Off  
Off  
Off  
seconds after the last button is pressed.  
Off Timer  
ECO Mode  
Network  
Remote Code  
Lamp Reset  
Press the last button for at least two seconds.  
A
Operate  
Exit  
Back  
BACK  
MENU  
Select  
.
Press for 2  
seconds or longer  
.
On the “Reset Lamp Time?” screen,  
select “Yes” and press the [OK] button  
3
0
The “LAMP” indicator and “STANDBY/ON”  
indicator blink alternately for three seconds.  
After that, the unit switches to the Standby  
mode.  
0
The lamp time is reset to zero.  
Reset Lamp Time?  
MEMO  
Yes  
No  
.
0
Reset the lamp time only when you have replaced the  
lamp.  
If the lamp time is reset while a lamp is in use, you may  
lose track of the timing for replacing the lamp. Doing  
so may result in using the lamp beyond the estimated  
limit, thereby causing lamp blowout.  
Maintaining the Cabinet and Remote Control  
0
Gently wipe off dirt on the cabinet with a soft cloth.  
If it is extremely dirty, wet a cloth in water, wring dry and use it to wipe off the dirt, followed by wiping again with a dry  
cloth.  
0
0
Pay attention to the following as the cabinet may deteriorate in condition or the paint may come off.  
0
Do not wipe with thinner or benzine  
Do not allow prolonged contact with rubber or plastic products  
Do not spray volatile chemicals such as insecticide  
0
0
62  
     
Cleaning and Replacing the Filter  
Clean the filter regularly Otherwise, the air intake  
efficiency may deteriorate, and malfunction may occur.  
3
Reinstall the inner filter  
CAUTION  
0
0
Make sure that you pull out the power plug from the  
outlet before cleaning or replacing the filter.  
Check that the left  
and right tabs are  
locked onto the unit  
Before turning this unit upside down and placing it on  
the floor or a table, make sure that you lay a soft rag  
in advance to prevent the projector from being  
scratched.  
1
.
Remove the inner filter  
If the filter is damaged or too dirty to be  
cleaned  
0
0
0
Replace with a new filter. A dirty filter will dirty the  
internal parts of the unit and cause shadows to appear  
on the video image.  
Pull out while  
pushing down the  
tab  
To purchase a new filter or when there is dirt in the  
internal parts of the unit, consult your authorized  
dealer or nearby service center.  
Inner filter (exchangeable filter)  
Product no.: F1K-0019-00  
.
2
Clean the filter  
.
0
Wash the filter with water and dry it in a shaded  
area.  
0
If the filter is extremely dirty, clean it with a  
neutral detergent. Put on rubber gloves when  
using a neutral detergent.  
0
After washing the filter with water, make sure  
that it is completely dry before reinstalling.  
Otherwise, electric shock or malfunction may  
occur.  
0
Do not clean the filter with a vacuum cleaner or  
air duster. The filter is soft and may be easily  
damaged.  
63  
     
Troubleshooting  
Before sending the unit to your authorized dealer for repair, please check the following points.  
The following symptoms are not malfunctions.  
You do not need to worry about the following symptoms if there is no abnormality on the screen.  
0
A part of the top or front surface of the unit is hot.  
A creaking sound is heard from the unit.  
An operating sound is heard from the inside of the unit.  
Color smear occurs on some screens.  
0
0
0
This unit is a digital device. This unit may become unable to operate normally due to external static or noise.  
Perform the following operations when such malfunctions occur.  
A
If the unit is in the Standby mode, pull out the power plug, followed by inserting it again  
B
Press the A [STANDBY/ON] button on the main unit to turn on the power again  
When “High Altitude Mode” is set to “On”, and “Lamp Power” is set to “High” during 3D mode, the fan will  
make louder noise than usual since it is designed to run at high speed in 3D mode.  
Power is not supplied  
Check  
Action  
Refer to  
Is the power cord disconnected?  
Is the lamp cover properly shut?  
Insert the power cord (plug) firmly.  
If the unit is in the Standby mode, remove the power plug P. 61  
and close the lamp cover properly. After that, insert the plug  
again.  
Is the lamp in the Cool-down mode?  
After exiting the Cool-down mode, turn on the power again. P. 22  
Power shuts down automatically  
Check  
Action  
Refer to  
Has “ECO Mode” been configured?  
Has “Off Timer” been configured?  
Set “ECO Mode” to “Off”.  
Set “Off Timer” to “Off”.  
Are the air inlets and exhaust vent  
blocked?  
Leave proper clearance when installing the unit.  
Is the filter dirty?  
Clean the filter.  
64  
   
Video image does not appear  
Check  
Action  
Refer to  
Is the correct external input selected? Select the correct external input terminal.  
Is the power of the AV device or PC  
turned on?  
Is the AV device or PC properly  
connected?  
Are the correct signals being output from Set the AV device or PC properly.  
the AV device or PC?  
Is the cable in use an HDMI-certified  
cable?  
Turn on the power of the AV device or PC and play the  
video.  
Connect the AV device or PC properly.  
Use an HDMI-certified high-speed cable. Also, use as  
short a cable as possible.  
Is an intermediate device (AV amplifier, Change the sequence of turning on the source device,  
divider, etc.) in use?  
intermediate device and the projector. And after turning on  
each device, ensure that the signal output is stable before  
turning on the next device.  
Is an old source device in use?  
Change the resolution setting of the source device. For  
details on how to change the setting, please refer to the  
instruction manual of the source device. Or, try connecting  
to the HDMI2 terminal and set “HDMI2 EDID” to “B”.  
3D images do not appear  
Check  
Action  
Refer to  
Do you see two images displayed side by Set “3D Format” to “Side by Side”  
side? Video images in the “Side by Side” format may not be  
recognized automatically in the case of 3D video images.  
Is an intermediate device (AV amplifier, Connect the source device to the projector directly, and P. 18  
divider, etc.) in use?  
check whether there is any improvement in the condition.  
If the condition improves, it is likely that this is not caused  
by malfunction of the projector.  
Is the cable in use an HDMI-certified  
cable?  
Use an HDMI-certified high-speed cable.  
Also, use as short a cable as possible.  
Is the power of the 3D Glasses turned If you are using the PK-AG2 or PK-AG3 3D Glasses, turn Check the  
on?  
instruction  
on the power manually.  
Check whether the PK-AG1 battery of the 3D Glasses has  
run out, and whether PK-AG2 and PK-AG3 are charged.  
manual of the 3D  
Glasses and 3D  
Synchro Emitter.  
Are the 3D Glasses charged?  
Are the 3D Glasses and 3D Synchro  
Emitter too far away from each other?  
Position them at an appropriate distance.  
Is the 3D Glasses and 3D Synchro  
Emitter combination correct?  
Check the model name of 3D Glasses and 3D Synchro  
Emitter, and use the correct combination.  
3D video image looks unnatural  
Check  
Action  
Refer to  
Are there overlapping video images?  
If there are overlapping video images partially, this is due P. 29  
to the crosstalk phenomenon.  
In this case, adjust “Crosstalk Cancel” accordingly.  
If there are overlapping video images partially, this is due P. 46  
to the crosstalk phenomenon.  
This phenomenon often occurs when there are drastic  
changes in the brightness.  
In this case, set Lamp Power to “High”  
65  
Video image looks unnatural  
Colors are unnatural  
Check  
Action  
Refer to  
Is the color space of the input signal  
correctly set?  
The color may turn out unnatural when the input signal is P. 49  
different from that in the projector setting.  
Set the “Color Space” for “Input Signal” correctly.  
Is the image correctly adjusted?  
Is the AV device or PC properly  
connected?  
Adjust “Color” and “Tint” accordingly.  
Connect the AV device or PC properly.  
* The video image may appear slightly reddish immediately after starting up. This is not a malfunction.  
Video image is fuzzy  
Check  
Action  
Refer to  
Is the focus correctly adjusted?  
Is the unit placed too near or too far away Set the unit at a correct distance from the screen.  
from the screen?  
Adjust the focus.  
Video image flickers  
Check  
Action  
Refer to  
Do you see horizontally-extended,  
overlapping video images?  
In this case, set “3D Format” to “Auto”  
Are you viewing the video images under This is caused by interference between the 3D glasses with  
a fluorescent light?  
the flickers of the fluorescent light.  
View with the fluorescent light turned off.  
Is “Lens Aperture” set to “Auto 1” or “Auto Set “Lens Aperture” to “Manual”  
2”?  
* Flickers may sometimes occur upon starting up the projector unit, or immediately after the projector is changed from  
floor-standing to ceiling mounted. This is attributable to the lamp or drive mechanism, and is likely not caused by  
malfunction of the projector.  
Projected image is dark  
Check  
Action  
Refer to  
Is the lamp near exhaustion?  
Check the lamp time in the “Information” menu. Prepare a P. 59  
new lamp unit or replace as soon as possible when the  
lamp is near exhaustion.  
Is the aperture closed?  
Set “Lens Aperture” to “Auto 1” or “Auto 2”, or set to  
“Manual” and open up the aperture manually.  
Set “Lamp Power” to “High”  
Is “Lamp Power” set to “Low”?  
Video image appears horizontally (vertically) extended  
Check  
Action  
Refer to  
Is “3D Format” set to “Side by Side”?  
Is “Anamorphic” set to a setting other  
than “Off”?  
Set “3D Format” to “Auto”  
Set “Anamorphic” to “Off”  
66  
Striped patterns appear on the screen  
Check  
Action  
Refer to  
Does the fabric of the screen have a  
regular pattern?  
Interference fringes may sometimes occur between the  
fabric pattern and the pixels. Please consult the authorized  
dealer.  
Video images are missing  
Check  
Action  
Refer to  
Has screen mask been configured?  
Is the display position misaligned?  
Set “Mask” to “Off”.  
Alter the “Picture Position” value so that the entire image P. 50  
appears on the screen.  
Remote control does not work  
Check  
Action  
Refer to  
Are the batteries correctly loaded?  
Match the polarities (t s) correctly when loading the  
batteries.  
Are the batteries exhausted?  
Is there an obstructing object between Remove any obstructing object.  
the remote control and remote sensor?  
Replace with new batteries.  
Is the remote control held too far away Hold the remote control closer to the sensor during use. P. 14  
from the unit?  
Are the IR (infrared) 3D Glasses and 3D As there is a possibility of signal interference, when you are P. 28  
Synchro Emitter in use?  
using the IR (infrared) 3D Glasses together with the 3D  
Synchro Emitter, try adjusting the orientation of the 3D  
Synchro Emitter.  
The lens cover does not close M N  
Check  
Action  
Refer to  
Is “Lens Cover” set to “Open”?  
Set “Lens Cover” under “Lens Control” in the setting menu P. 51  
to “Auto”.  
Noise is heard  
Check  
Action  
Refer to  
Is the exhaust vent blocked?  
Is the unit used near a heater or air-  
conditioner?  
Check the installation condition of the projector.  
When the surrounding temperature of the projector is high,  
the fan revolution speed increases to protect the projector  
unit, hence a louder operating sound.  
Are you viewing 3D video images?  
“Lamp Power” is set automatically to “High” to ease viewing P. 46  
of 3D video images, hence a louder fan operating sound.  
If you are bothered by the sound, set it to “Low”.  
Is the “Picture Mode” or “Color Profile” Operating sound is generated by the cinema filter. This is  
changed?  
not a malfunction.  
M N only  
Did you change the “4K e-shift” setting Switching sound is generated. This is not a malfunction.  
for “MPC Level”?  
There are small black or colored dots on the screen  
The D-ILA device is manufactured using high-precision technologies, but there may be some (less than 0.01%) missing  
pixels or pixels that remain permanently lit. This is not a malfunction.  
67  
When the Following Messages Appear...  
Message  
Description  
Action  
0
0
No device is connected to the input Input the video signals.  
terminal.  
The input terminal is connected but  
there is no signal.  
No Input  
.
A video signal that cannot be used with Input video signals that can be used.  
this unit has been input (The names of (P. 78)  
input terminals such as “HDMI-1” and  
HDMI-1  
.
“HDMI-2” will be displayed in yellow).  
Indicates that the lamp needs to be  
replaced soon.  
Get ready a new lamp unit and replace  
as soon as possible. Reset the lamp time  
Lamp replacement  
Back  
BACK  
To clear the message, press the [BACK] after replacing the lamp. (P. 60, 62)  
button on the operation panel of the  
.
projector unit or the remote control.  
68  
   
External Control  
It is possible to control this unit by connecting it to a PC using an RS-232C cross cable (D-sub 9-pin).  
The projector can be controlled by connecting it to a PC through the computer network with a LAN cable for control  
commands to be sent to the projector.  
0
Please use it after you have gained proper understanding from professional books or consulting the system  
administrator.  
RS-232C Specifications  
This Unit  
Pin No.  
Signal  
Function  
Receive data  
Signal Direction  
1
5
2
3
5
RxD  
TxD  
GND  
N/C  
PC " This unit  
6
9
Transmission data  
Signal ground  
This unit " PC  
1, 4, 6 - 9  
0
PC refers to the controller, such as a personal computer.  
Mode  
Non-synchronous  
D0 D1 D2 D3 D4 D5 D6 D7  
Stop bit  
Character length  
Parity  
8 bit  
None  
1
Start bit  
Start bit  
Stop bit  
1
Data rate  
Data format  
19200 bps  
Binary  
TCP/IP Connection  
Before controlling via LAN, it is necessary to establish connection of the TCP layer by a “3-way handshake”, followed  
by sending out “PJREQ” and receiving “PJACK” within five seconds after the projector sends out “PJ_OK” for connection  
authentication.  
If you are unable to complete sending within five seconds, or when “PJ_NG” or “PJNAK” is received, check the operating  
status of the projector, followed by performing the steps again starting from establishment of a TCP connection.  
Within 5 Seconds  
Projector  
PJ_OK  
PJACK  
Establishment of TCP Connection  
TCP Port No. 20554  
3-way Handshake  
Projector Control  
PJREQ  
Connection Authentication Procedure  
Controlling PC  
.
69  
       
Command Format  
The command between this unit and the computer consists of “Header”, “Unit ID”, “Command”, “Data” and “End”.  
0
Header (1 byte), Unit ID (2 bytes), Command (2 bytes), Data (n bytes), End (1 byte)  
Header  
This binary code indicates the start of communication.  
Binary Code  
Type  
Description  
21  
3F  
40  
06  
Operating command PC " This unit  
Reference command PC " This unit  
Response command This unit " PC  
ACK  
This unit " PC (returns to PC after the command is accepted without  
error)  
Unit ID  
This is a code that specifies the unit. The binary code is fixed at “8901”.  
Command and data  
Operating command and data (binary code)  
Reference command and data (binary code)  
Command  
0000  
Type  
Description  
Command  
5057  
Type  
Power  
Description  
Connection Check whether communication is  
check  
During standby or when power is  
on  
enabledbetweenthisunitandthe  
PC during standby.  
supply  
30: Standby mode  
31: When power is on  
32: In the Cool-down mode  
34: When error occurs on this unit  
5057  
Power  
supply  
During standby  
31: Turns on the power  
When power is on  
30: Turns off the power (Standby  
mode)  
4950  
Input  
When power is on  
36: HDMI 1  
37: HDMI 2  
4950  
5243  
Input  
When power is on  
36: HDMI 1  
37: HDMI 2  
Remote Sends the same code as the  
control  
supplied remote control.  
0
End  
This code indicates the end of communication. The binary code is fixed at “0A”.  
70  
 
Remote Control Code  
Binary code is sent during communication.  
0
The following applies to the case when the remote control code is “A”. In the case of “B”, add “36” to the beginning  
of the code.  
Remote Control Button Name  
STAND BY  
Binary Code  
37 33 30 36  
37 33 30 35  
37 33 37 30  
37 33 37 31  
37 33 37 34  
37 33 44 38  
37 33 44 39  
37 33 44 41  
37 33 33 30  
37 33 32 30  
37 33 43 35  
37 33 31 44  
37 33 30 31  
37 33 30 32  
37 33 33 34  
37 33 33 36  
Remote Control Button Name  
Binary Code  
37 33 32 46  
37 33 32 45  
37 33 30 33  
37 33 36 41  
37 33 36 38  
37 33 46 34  
37 33 38 38  
37 33 46 35  
37 33 46 30  
37 33 38 41  
37 33 37 33  
37 33 37 35  
37 33 37 36  
37 33 44 36  
37 33 37 32  
OK  
ON  
MENU  
HDMI 1  
HDMI 2  
INFO.  
BACK  
NATURAL  
CINEMA  
MODE 1  
MODE 2  
MODE 3  
LENS CONTROL  
LENS AP.  
ANAMO.  
HIDE  
PICTURE MODE  
COLOR PROFILE  
GAMMA SETTINGS  
MPC  
C.M.D.  
ADVANCED MENU  
GAMMA  
J
COLOR TEMP.  
3D FORMAT  
PIC. ADJ.  
K
I
H
71  
   
Communications Example  
This section shows the communication examples of RS-232C.  
Operating command  
Type  
Command  
Description  
Connection check  
Connection check  
PC " This unit: 21 89 01 00 00 0A  
This unit " PC: 06 89 01 00 00 0A  
Power (On)  
Power (Off)  
PC " This unit: 21 89 01 50 57 31 0A  
When power is turned on from the  
Standby mode  
This unit " PC: 06 89 01 50 57 0A  
PC " This unit: 21 89 01 50 57 30 0A  
This unit " PC: 06 89 01 50 57 0A  
When power is turned off (Standby  
mode) from power-on mode  
Remote control  
(MENU)  
PC " This unit: 21 89 01 52 43 37 33 32 45 0A  
This unit " PC: 06 89 01 52 43 0A  
When the same operation as  
pressing the [MENU] button on the  
remote control is performed  
Reference command  
Type  
Command  
Description  
Power (On)  
PC " This unit: 3F 89 01 50 57 0A  
This unit " PC: 06 89 01 50 57 0A  
This unit " PC: 40 89 01 50 57 31 0A  
When information on the power-on  
state is acquired  
Input (HDMI 1)  
PC " This unit: 3F 89 01 49 50 0A  
This unit " PC: 06 89 01 49 50 0A  
This unit " PC: 40 89 01 49 50 36 0A  
When information on HDMI 1 input  
is acquired  
72  
 
Specifications  
Product Name  
Model Name  
D-ILA Projector  
DLA-X990RB, DLA-X790RB, DLA-X590RB*1  
Display Panel/Size  
D-ILA device *2, 3  
0.7" (1920 x 1080 pixels) x 3 (total no. of pixels: approx. 6.22 million)  
Projection Lens  
2.0 x power zoom lens (1.4:1 to 2.8:1), motorized zoom and focus  
Light-source Lamp  
265 W ultra-high pressure mercury lamp [product no.: PK-L2615U]  
Average lifespan: 4500 hours (“Low” mode)  
Screen Size  
Brightness  
Approx. 60" to 200" (Aspect ratio of 16:9)  
2000 lm M  
1900 lm N  
1800 lm O  
Projection Distance  
Input Compatibility Signal  
Display Resolution  
3840 x 2160 pixels *4  
Input Terminal HDMI Input  
Output Terminal Trigger Terminal  
Dual, HDMI 19-pin x 2 (HDCP 2.2-compatible) *5  
1 system, Ø 3.5 mm DC Power Jack (E)  
DC OUT 12 V, 0.1 A  
3D synchro  
Control Terminal RS-232C Terminal  
LAN Terminal  
Dedicated terminal for 3D Synchro Emitter (1 system, mini-DIN 3-pin)  
1 system, D-sub 9-pin (male) (external control)  
1 system, RJ-45 plug  
Power Requirements  
AC 100 V to 240 V, 50 Hz/60 Hz  
Power Consumption  
380 W (during networked standby: 1.5 W *6, during standby: 0.4 W *7)  
Operation Environment  
Temperature: 5°C to 35°C; humidity: 20% to 80%; storage  
temperature: -10°C to 60°C  
Installation Height  
Below 5,000 ft (1524 m)  
Dimensions (Width x Height x Depth)  
Approx. 455 mm x 179 mm x 472 mm (approx. 17.9 in x 7.0 in x 18.6  
in) (excluding feet and protrusions)  
Mass  
15.6 kg (approx. 34.4 lb) (M N)  
15.4 kg (approx. 34.0 lb) (O)  
Accessories  
*1 “B” indicates that the main unit is black in color.  
*2 D-ILA is the abbreviation for Direct drive Image Light Amplifier.  
*3 D-ILA devices are manufactured using extremely high-precision technology with a pixel effectiveness of 99.99%.  
Only 0.01% or less of the pixels are either missing or would remain permanently lit.  
*4 During 3D playback, the pixel is set to 1920 x 1080.  
*5 HDCP is the abbreviation for High-bandwidth Digital Content Protection system. The image of the HDMI input  
terminal may not be displayed in some cases due to changes in the HDCP specifications.  
*6 The power consumption of this product during networked standby when all wired network ports are connected  
is 1.5 W.  
0
Design and specifications are subject to change without prior notice.  
0
Please note that some of the pictures and illustrations may have been abridged, enlarged or contextualized in order  
to aid comprehension. Images may differ from the actual product.  
73  
   
M N have obtained the “THX 3D Display Certification” by THX.  
In addition to 2D movies, you can also enjoy faithful reproduction of images in a “quality as  
intended by the filmmaker” during playback of 3D movies.  
The THX 3D certification is “an indication of high definition and high resolution”, which is  
granted to products that have cleared more than 400 image quality tests.  
M N are isf-certified, so calibration can be performed by an isf-certified trainer.  
®
After calibration is performed, an isf mode is added to the Picture mode.  
For more details, please refer to the isf website.  
About Trademarks and Copyrights  
HDMI, HDMI logo and High-Definition Multimedia Interface are trademarks or registered  
trademarks of HDMI Licensing LCC.  
“x.v.Color” and the “x.v.Color” logo are trademarks of Sony Corporation  
74  
 
Screen Size and Projection Distance  
When a 16:9 screen is used  
Screen Size  
Projection Distance  
Wide-end (m) Tele-end (m)  
Diagonal (Model)  
Width (mm)  
1328  
1549  
1771  
1992  
2214  
2435  
2656  
2878  
3099  
3320  
3542  
3763  
3984  
4206  
4427  
Height (mm)  
747  
60  
1.78  
2.09  
2.4  
3.66  
4.28  
4.89  
5.51  
6.13  
6.75  
7.36  
7.98  
8.60  
9.22  
9.84  
10.45  
11.07  
11.68  
12.30  
70  
872  
80  
996  
90  
1121  
1245  
1370  
1494  
1619  
1743  
1868  
1992  
2117  
2241  
2366  
2490  
2.7  
100  
110  
120  
130  
140  
150  
160  
170  
180  
190  
200  
3.01  
3.31  
3.62  
3.92  
4.23  
4.53  
4.84  
5.14  
5.45  
5.75  
6.06  
Screen Size  
Projection Distance  
Tele-end (ft)  
12.01  
Diagonal (Model)  
Width (in)  
52.3  
Height (in)  
29.4  
34.3  
39.2  
44.1  
49.0  
53.9  
58.8  
63.7  
68.6  
73.5  
78.4  
83.3  
88.2  
93.1  
98.0  
Wide-end (ft)  
5.84  
60  
70  
61.0  
6.86  
14.04  
80  
69.7  
7.87  
16.04  
90  
78.4  
8.86  
18.08  
100  
110  
120  
130  
140  
150  
160  
170  
180  
190  
200  
87.2  
9.88  
20.11  
95.9  
10.86  
11.88  
12.86  
13.88  
14.86  
15.88  
16.86  
17.88  
18.86  
19.88  
22.15  
104.6  
113.3  
122.0  
130.7  
139.4  
148.1  
156.9  
165.6  
174.3  
24.15  
26.18  
28.21  
30.25  
32.28  
34.28  
36.32  
38.32  
40.35  
75  
 
When a 4:3 screen is used  
Screen Size  
Width (mm)  
Projection Distance  
Wide-end (m) Tele-end (m)  
Diagonal (Model)  
Height (mm)  
914  
60  
1219  
1422  
1626  
1829  
2032  
2235  
2438  
2642  
2845  
3048  
3251  
2.22  
2.60  
2.98  
3.36  
3.74  
4.11  
4.49  
4.87  
5.25  
5.63  
6.00  
4.49  
5.24  
6.00  
6.75  
7.51  
8.26  
9.02  
9.77  
10.53  
11.28  
12.04  
70  
1067  
80  
1219  
90  
1372  
100  
110  
120  
130  
140  
150  
160  
1524  
1676  
1829  
1981  
2134  
2286  
2438  
Screen Size  
Projection Distance  
Tele-end (ft)  
14.73  
Diagonal (Model)  
Width (in)  
48.0  
Height (in)  
36.0  
Wide-end (ft)  
7.28  
60  
70  
56.0  
42.0  
8.53  
17.19  
80  
64.0  
48.0  
9.78  
19.68  
90  
72.0  
54.0  
11.02  
12.27  
13.48  
14.73  
15.98  
17.22  
18.47  
19.68  
22.15  
100  
110  
120  
130  
140  
150  
160  
80.0  
60.0  
24.64  
88.0  
66.0  
27.10  
96.0  
72.0  
29.59  
104.0  
112.0  
120.0  
128.0  
78.0  
32.05  
84.0  
34.55  
90.0  
37.01  
96.0  
39.50  
* Projection to a 4:3 screen larger than 163" is equivalent to a size that is larger than 200" in the 16:9 format, and is  
beyond our guarantee coverage.  
76  
When a 2.35:1 screen is used  
Screen Size  
Width (mm)  
Projection Distance  
Wide-end (m) Tele-end (m)  
Diagonal (Model)  
Height (mm)  
597  
60  
1402  
1636  
1870  
2103  
2337  
2571  
2805  
3038  
3272  
3506  
3740  
3973  
4207  
4441  
4674  
1.95  
2.28  
2.60  
2.93  
3.26  
3.58  
3.91  
4.23  
4.56  
4.88  
5.21  
5.53  
5.86  
6.19  
6.51  
3.91  
4.56  
5.21  
5.86  
6.51  
7.16  
7.81  
8.47  
9.12  
9.77  
10.42  
11.07  
11.72  
12.37  
13.02  
70  
696  
80  
796  
90  
895  
100  
110  
120  
130  
140  
150  
160  
170  
180  
190  
200  
995  
1094  
1193  
1293  
1392  
1492  
1591  
1691  
1790  
1890  
1989  
Screen Size  
Projection Distance  
Tele-end (ft)  
12.83  
Diagonal (Model)  
Width (in)  
55.2  
Height (in)  
23.5  
27.4  
31.3  
35.2  
39.2  
43.1  
47.0  
50.9  
54.8  
58.7  
62.6  
66.6  
70.5  
74.4  
78.3  
Wide-end (ft)  
6.40  
60  
70  
64.4  
7.48  
14.96  
80  
73.6  
8.53  
17.09  
90  
82.8  
9.61  
19.23  
100  
110  
120  
130  
140  
150  
160  
170  
180  
190  
200  
92.0  
10.70  
11.75  
12.83  
13.88  
14.96  
16.01  
17.09  
18.14  
19.23  
20.31  
21.36  
21.36  
101.2  
110.4  
119.6  
128.8  
138.0  
147.2  
156.4  
165.6  
174.8  
184.0  
23.49  
25.62  
27.79  
29.92  
32.05  
34.19  
36.32  
38.45  
40.58  
42.72  
77  
Types of Possible Input Signals  
Video  
Digital Video Signal  
480p, 576p, 720p/50 Hz, 720p/60 Hz, 1080i/50 Hz, 1080i/60 Hz, 1080p/24  
Hz, 1080p/50 Hz, 1080p/60 Hz, 3840×2160/24Hz, 3840×2160/25Hz,  
3840×2160/30Hz, 3840×2160/50Hz*1, 3840×2160/60Hz*1,  
4096×2160/24Hz*2, 4096×2160/25Hz*2, 4096×2160/30Hz*2,  
4096×2160/50Hz*1, 2, 4096×2160/60Hz*1, 2  
3D Signal  
Frame Packing  
720p/50 Hz, 720p/60 Hz, 1080p/24 Hz  
Side-by-side  
1080i/60 Hz, 1080p/60 Hz, 1080i/50 Hz, 1080p/50 Hz, 1080p/24 Hz,  
720p/50 Hz, 720p/60 Hz  
Top-and-bottom  
720p/50 Hz, 720p/60 Hz, 1080p/24 Hz  
*1 When the color space is RGB/YCbCr(4:4:4), only 8-bit input is supported.  
*2 The display image when the input signal is 4096×2160  
4096  
3840  
Display Area  
.
PC signal (HDMI)  
No. of  
Effective  
Lines  
Total No. Total No.  
No. of  
dot CLK  
[MHz]  
No. Designation Resolution  
fh [kHz]  
fv [Hz]  
of Dots  
[dot]  
of Lines Effective  
[line]  
Dots [dot]  
[line]  
1
2
3
4
5
6
7
8
VGA 60  
640×480  
640×480  
800×600  
1024×768  
1280×768  
1440×900  
31.500  
31.469  
37.879  
48.363  
47.760  
55.919  
60.000  
25.200  
25.175  
40.000  
65.000  
79.998  
800  
525  
640  
480  
VGA 59.94  
SVGA 60  
XGA 60  
59.940  
60.317  
60.004  
60.000  
59.999  
60.020  
60.002  
800  
525  
640  
480  
1,056  
1,344  
1,675  
628  
800  
600  
806  
1,024  
1,280  
1,440  
1,280  
1,680  
768  
WXGA 60  
WXGA+ 60  
SXGA 60  
796  
768  
106.470 1,904  
108.000 1.688  
147.140 2,256  
932  
900  
1280×1024 63.981  
1,066  
1,087  
1,024  
1,050  
WSXGA+ 60 1680×1050 65.222  
* Even when signals can be input, video images may not be projected properly depending on the PC or cable in use.  
When this occurs, switching to another compatible resolution or changing the cable may help to resolve the problem  
in some cases.  
78  
   
Indicator Display on the Main Unit  
Meaning of the lighting figures  
STANDBY/ON  
LAMP  
WARNING  
The indicator lights up.  
The indicator appears blinking.  
.
Operation mode display  
Displays using the different colors and solid/blinking light of the “STANDBY/ON” indicator.  
“STANDBY/ON” lights up (red)  
“STANDBY/ON” lights up (green)  
All lights off  
In standby state  
During lamp startup  
During projection  
STANDBY/ON  
LAMP  
WARNING  
STANDBY/ON  
LAMP  
WARNING  
STANDBY/ON  
LAMP  
WARNING  
“STANDBY/ON” blinking (green)  
When the video image is temporarily hidden (HIDE is on)  
“STANDBY/ON” blinking (red)  
In the Cool-down mode  
S
TANDBY
/ON  
LAMP  
WARNING  
S
TANDBY
/ON  
LAMP  
WARNING  
.
Estimated timing for lamp replacement  
Displays using the solid/blinking light of the “LAMP” indicator. The “STANDBY/ON” indicator, which shows the operating  
mode of the unit, is displayed simultaneously as described above.  
“LAMP” lights up (orange)  
STANDBY/ON  
LAMP  
WARNING  
When lamp replacement is  
near  
.
79  
   
Warning display  
You can tell the details of a warning from the (repeated) displays of the “WARNING” and “LAMP” indicators. The  
“STANDBY/ON” indicator, which shows the operating mode of the unit, is displayed simultaneously as described above.  
The Warning mode is activated once the message is displayed. Projection is interrupted, and the cooling fan is turned  
on for about 100 seconds.  
The power cannot be turned on again while cooling is in progress. Check the following after cooling is complete.  
Blinking  
Indicator Status (Solid/Blinking)  
Description  
Check and Countermeasure  
Frequency  
0
0
x1  
x2  
x3  
Abnormality in the power supply  
Cooling fan stopped abnormally  
Check that nothing is blocking  
the air inlets.  
Check that the external  
temperature is normal.  
STANDBY/ON  
LAMP  
WARNING  
Internal temperature is abnormally  
high  
Mode  
(*)  
(Red)  
Countermeasure: Leave the unit  
unoperated until it cools down.  
After that, turn on the power again.  
Display  
x4  
x5  
x1  
x2  
x3  
x4  
External temperature is too high  
Abnormal circuit operation  
Abnormal circuit operation  
.
.
STANDBY/ON  
LAMP  
WARNING  
Mode (Orange) (Red)  
0
Abnormal operation of the lens  
cover  
Check that nothing is blocking  
the lens cover.  
Display  
Blinking  
Simultaneously  
Countermeasure: Turn on the  
power again.  
0
x1  
Lamp does not light up and unit is  
unable to project  
Check that the lamp unit and  
STANDBY/ON  
LAMP  
WARNING  
lamp cover are correctly  
installed.  
x2  
x3  
Lamp goes out during projection  
When the lamp cover is removed  
Countermeasure: Turn on the  
power again.  
Mode (Orange) (Red)  
Display  
.
If the Warning mode is activated again, wait for the cooling fan to stop, followed by pulling out the power plug from the  
outlet.  
Request for repair at your authorized dealer or a nearby service center.  
(*) If the scheduled time for lamp replacement is exceeded, the indicator may light up.  
80  
Dimensions  
(Unit: mm (in))  
Top Surface  
Bottom Surface  
5
59 (2.3)  
337 (13.3)  
(0.2)  
455 (17.9)  
Lens  
.
Lens  
.
Rear Surface  
Front  
227.5 (9.0)  
110 92  
Ø60  
(2.4)  
(4.3) (3.6)  
Lamp Cover  
Lens Center  
.
.
0
The dimensions are identical for all the models.  
81  
Index  
A
K
L
B
C
M
N
O
P
Dimensions .......................................................... 81  
D
E
F
R
S
G
H
I
82  
 
.
© 2017 JVCKENWOOD Corporation  
1117KSY-SW-XX  

Whirlpool 1172397 User Manual
Sanyo Ecoi C1305dxhn8 User Manual
Samsung Avmch128ca1 User Manual
Samsung As24a1 A2 Rc User Manual
Newair Titanclean P600 User Manual
HP ELITEBOOK 8460W User Manual
EMERSON MOBREY MSP400RH User Manual
CYBERPOWER PDU81001 User Manual
CRAFTSMAN 917.387205 User Manual
CRAFTSMAN 536.887752 User Manual