PD 40
Operating instructions
Brugsanvisning
Bruksanvisning
Bruksanvisning
Käyttöohje
en
da
sv
no
fi
Инструкция по зксплуатации ru
Lietoßanas pamåcîba
Instrukcija
lv
lt
Kasutusjuhend
et
2
3
4
6
2
1
4
3
5
6
1
2
5
1
7
PD 40 laser range meter
1 These numbers refer to the corresponding illustra-
tions. The illustrations can be found on the foldಣout
cover pages. Keep these pages open while studying
the operating instructions.
In these operating instructions, the designation “the
tool” always refers to the PD 40 laser range meter.
It is essential that the operating instructions
are read before the tool is operated for the
first time.
en
Always keep these operating instructions
together with the tool.
Parts, operating controls and indicators 1
Ensure that the operating instructions are
with the tool when it is given to other
persons.
On/off button
Side measure button
Graphic display
Measure button
Delete (clear) button
Horizontal bubble
Area button
@
;
=
%
&
(
)
+
§
/
:
·
$
£
|
Contents
1. General information
Page
17
18
22
22
23
24
28
30
31
32
32
33
2. Description
Folding spike
3. Insert tools, accessories
4. Technical data
{/" thread for PDA 71 measuring extension
Rear contact points
Minus button
Plus button
Reference button
5. Safety rules
6. Before use
7. Operation
8. Care and maintenance
9. Troubleshooting
10. Disposal
Laser exit lens
Receiving lens
11. Manufacturer’s warranty ಣ tools
12. EC declaration of conformity
1. General information
1.1 Safety notices and their meaning
DANGER
Draws attention to imminent danger that could lead
1.2 Explanation of the pictograms and other
information
Warning signs
to serious bodily injury or fatality.
WARNING
Draws attention to a potentially dangerous situation
that could lead to serious personal injury or fatality.
General
warning
CAUTION
Draws attention to a potentially dangerous situation
that could lead to slight personal injury or damage to
the equipment or other property.
NOTE
Draws attention to an instruction or other useful
information.
17
Symbols
Location of identification data on the tool
The type designation and serial number can be found
on the type identification plate on the tool. Make a
note of this data in your operating instructions and
always refer to it when making an enquiry to your
Hilti representative or service department.
Read the
operating
instructions
before use.
Return waste
material for
recycling.
Laser class II according
to CFR 21, § 1040 (FDA)
en
Type:
>1/4s
Serial no.:
Laser class 2
in accordance
with
Do not look
into the beam.
Temperature
indicator
EN 60825ಣ
1:2003
Battery status
indicator
Hardware
errors
Unfavorable
operating
conditions
Type identification plate
01
PD 40
Made in Germany
Hilti
=
trademark of Hilti Corp., Schaan, LI
Serial number
AVOID EXPOSURE
Laser radiation is emitted from this aperture
LASER RADIATION - DO NOT
STARE INTO BEAM
620-690nm/0.95mW max.
CLASS II LASER PRODUCT
DIN EN 60825-1:2003
This device complies with part 15 of
the FCC Rules. (1) This device may not
cause harmful interference, and (2) this
device must accept any inter-
ference received, including inter-
ference that may cause undesired operation.
Item No.: 30399
Manufactured:
Power: 3V nom/400 mA
PD 40
2. Description
2.1 Use of the product as directed
The tool is designed for measuring distances, calculating areas and adding or subtracting distances.
Do not use the tool as a leveling tool.
Measurements taken from plastic foam materials such as polystyrene foam, from snow or from highly reflective
surfaces (mirrors, glass, etc.) may produce inaccurate results.
The tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or
when used not as directed.
18
Take the influences of the surrounding area into account. Do not use the appliance where there is a risk of fire
or explosion.
Observe the information printed in the operating instructions concerning operation, care and maintenance.
To avoid the risk of injury, use only genuine Hilti accessories and additional equipment.
Modification of the tool is not permissible.
NOTE
en
Observe the permissible operating and storage temperatures.
2.2 Display
The measurements, settings and tool status are shown in the display. When the tool is in measuring mode,
the measurements taken are shown at the bottom of the display area (the result line). When using a function,
e.g. area measurement, the distances measured are shown in the intermediate result line and the calculated
result is shown at the bottom of the display (the result line).
2.3 Display illumination
In low light conditions, the display is illuminated automatically as soon as a button is pressed. The display
illumination intensity is reduced to 50% after 10 seconds. If no button is pressed over a period of 20 seconds,
the display illumination switches off automatically.
NOTE
Illumination of the display consumes battery power. Shorter battery life is therefore to be expected when this
feature is used frequently.
2.4 Basic principle
The distance is measured along a laser beam emitted by the tool to the point at which the beam strikes
a reflective surface. The target from which the measurement is taken is clearly identified by the red laser
measuring spot. The range of the tool depends on the reflectance and structure of the target surface from
which measurements are taken.
2.5 Measuring principle
The tool emits a visible laser beam carrying signal pulses which are reflected by the target. The time between
reflected pulses is used as a basis for determining the distance.
This measuring principle permits highly accurate and reliable measurement of distances to objects without
need for special reflectors.
2.6 Standard measuring display mode
Standard measuring display mode is always activated when the “On/off” or “Measure” button is pressed to
switch the tool on.
19
2.7 Symbols in the display
Temperature
Temperature too high
(>+50°C) / too low (<ಣ
10°C).
Allow the tool to cool down or warm up.
Unfavorable operating
conditions
Insufficient reflected
laser light.
Observe the minimum measuring distance (50 mm
from the front edge of the tool); clean the lenses;
take measurements from a different surface or use a
target plate.
en
General hardware error
Switch the tool off and on again. If the fault persists,
please contact Hilti Service.
2.8 Control panel
Measure button
Activates the laser beam.
Begins distance measurement.
Activates continuous measuring mode (long press,
approx. 2 sec.).
Stops continuous measuring mode.
Activates distance and area addition.
Distances shown in the standard measuring display
are added.
Adds areas when in area measuring mode.
Activates distance and area subtraction.
Distances shown in the standard measuring display
are subtracted.
Subtracts areas when in area measuring mode.
Activates area measuring mode.
Plus button
Minus button
Area button
When measurements have been taken: Deletes all
measurements and restarts the function.
When no measurements have been taken: ends area
measuring mode.
Stops continuous measuring (tracking).
Delete (clear) button
The Cತbutton has various Stops continuous measuring (tracking).
functions depending on
operating mode.
Clears the standard measuring display.
Clears the last measurement and returns to
“Functions”.
Ends area measuring mode if no measurements
have been taken.
On/off button
When the tool is switched off, press the button
briefly to switch it on.
When the tool is switched off, press and hold the
button to activate the menu.
When the tool is switched on, press the button
briefly to switch it off.
Reference button
Switches the various measuring references between
front and rear.
20
2.9 Battery condition indicator
Number of segments shown
Charge status in %
4
3
2
1
0
= 100 % capacity
= 75 % capacity
= 50 % capacity
= 25 % capacity
Fully discharged
en
2.10 Items supplied as standard
1
1
2
1
1
1
PD 40 laser range meter
Hand strap
Batteries
Battery compartment key
Operating instructions
Manufacturer’s certificate
2.11 PUA 60 laser visibility glasses
The laser visibility glasses have no protective function and thus do not protect the eyes from laser beams. As
these glasses limit color vision they must not be worn by persons driving on a public road and must not be
used to look directly into the sun.
The PUA 60 laser visibility glasses improve laser beam visibility considerably.
2.12 PDA 50 / 51 / 52 target plate
The PDA 50 target plate is made of durable plastic with a special reflective coating. Use of the target plate is
recommended at distances greater than 10 m in poor light conditions.
The PDA 51 target plate has no reflective coating and its use is recommended in poor light conditions and at
short distances. The PDA 52 target plate is equipped with the same reflective coating as the PDA 50 but is
considerably larger in size (A4 format, 210 x 297 mm). This makes it much easier to aim the tool at the target
plate over long distances.
NOTE
For reliable distance measurements, care should be taken to ensure that the laser beam strikes the target plate
at right angles as far as possible. The laser spot on the target plate and the measuring reference point (starting
point) may otherwise be in different planes (parallax error).
NOTE
When the target plate is used and very high accuracy is required, 1.2 mm should be added to the measurement
obtained.
2.13 PDA 71 measuring extension
The measuring extension is made from aluminium and is equipped with a nonಣconductive synthetic rubber
grip. The screw on the measuring extension should be screwed into the threaded bush on the rear contact
surface of the PD 40. When the measuring extension is screwed onto the tool, the rear reference is then
relocated to the tip of the measuring extension, i.e. the rear reference is extended by 1270 mm (50 inches).
21
3. Insert tools, accessories
Target plate
Target plate
Target plate
Measuring extension
PDA 50
PDA 51
PDA 52
PDA 71
en
Hand strap
Soft pouch
Laser visibility glasses
PDA 60
PDA 65
PUA 60
4. Technical data
Right of technical changes reserved.
Technical data
Values
Power supply
3V DC AAಣsize batteries
Battery condition check
Battery condition indicator with 4 segments showing
100%, 75%, 50%, 25% charge : No segments
shown: The batteries are exhausted
0.05…200 m
Measuring range
Typical measuring range without target plate
Drywall panel, white: 100 m
Concrete, dry: 70 m
Brick, dry: 50 m
Accuracy
Typically 1.0 mm for single and continuous
measurement
1 mm
Smallest unit displayed
Beam diameter
Beam length 10 m: Max. 6 mm
Beam length 50 m: Max. 30 mm
Beam length 100 m: Max. 60 mm
Basic operating modes
Single measuring, continuous measuring, calcula-
tion/functions
Display
Laser
Illuminated dotಣmatrix display with permanent
indication of operating mode and battery condition
Visible 635 nm, Output power less than 1 mW: Laser
class 2
IEC 825ತ 1:2003CFR 21 § 1040 (FDA)
Laser: 1 min
Tool: 10 min
Automatic cutಣout
Battery life
Max. number of measurements with laser
beam switched on for a time of 10 s Al-
kaline 8,000…10,000 NiMH 6,000…8,000
Operating temperature range
-10…+50°C
Storage temperature
-30…+70°C
Protection class (except battery compartment)
IP 54 protection against dust and water jets
IEC 529
22
Technical data
Values
Weight without batteries
Dimensions
170 g
120 mm x 55 mm x 28 mm
Menu / units
Distance
Area
Volume
m
cm
mm
mt
mt
mt
mu
mu
mu
Meters
en
Centimeters
Millimeters
Inches, decimal
{/೩ inch
{/ೢ೧ inch
{/ೣ inch
Feet, decimal
Feetಣinchesಣ{/೩
Feetಣinchesಣ{/ೢ೧
Feetಣinchesಣ{/ೣ
Yards, decimal
In
Inchest
Inchest
Inchest
Inchest
Feett
Feett
Feett
Feett
Yardst
Inchesu
Inchesu
Inchesu
Inchesu
Feetu
Feetu
Feetu
Feetu
Yardsu
In {/೩
In {/ೢ೧
In {/ೣ
Ft
Ft {/೩
Ft {/ೢ೧
Ft {/ೣ
Yd
5. Safety rules
In addition to the information relevant to safety i) Do not point the tool toward the sun or other
given in each of the sections of these operating
instructions, the following points must be strictly
observed at all times.
powerful light sources.
5.2 Proper organization of the workplace
a) Avoid unfavorable body positions when working
on ladders or scaffolding. Make sure you work
from a safe stance and stay in balance at all
times.
b) Check the measuring reference setting before
taking the measurement.
5.1 Basic information concerning safety
a) Do not render safety devices ineffective and do
not remove information and warning notices.
b) Keep laser tools out of reach of children.
c) Failure to follow the correct procedures when
opening the tool may cause emission of laser c) When the tool is brought into a warm environ-
radiation in excess of class 2. Have the tool
repaired only at a Hilti service center.
ment from very cold conditions, or viceಣversa,
allow it to become acclimatized before use.
d) Check that the tool functions correctly each time d) As a precaution, check the previous settings and
before use. adjustments you have made.
e) Operation of the tool in the proximity of pregnant e) When setting up the tool with the aid of the
women is not permissible.
f) Measurements taken from surfaces with low re-
bubble level, view the bubble level at a slight
angle.
flectivity in highly reflective surroundings may be f) Secure the area in which you are working and
inaccurate.
take care to avoid directing the beam towards
other persons or towards yourself when setting
up the tool.
g) Measurements taken through panes of glass or
other objects may be inaccurate.
g) Use the tool only within its specified limits.
h) Rapid changes in the conditions under which
the measurement is taken, e.g. persons walking h) Observe the accident prevention regulations ap-
through the laser beam, may lead to inaccurate
results.
plicable in your country.
23
5.3 Electromagnetic compatibility
5.5 Electrical
Although the tool complies with the strict require- a) Keep the batteries out of reach of children.
ments of the applicable directives, Hilti cannot en-
tirely rule out the possibility of the tool being subject
to interference caused by powerful electromagnetic
radiation, leading to incorrect operation. Check the
accuracy of the tool by taking measurements by other
means when working under such conditions or if you
are unsure. Likewise, Hilti cannot rule out the pos-
sibility of interference with other devices (e.g. aircraft
navigation equipment). The tool complies with the
requirements of class A; The possibility of interfer-
ence occurring in a domestic environment cannot be
excluded.
b) Do not allow the batteries to overheat and do not
expose them to fire. The batteries may explode or
release toxic substances.
c) Do not charge the batteries.
d) Do not solder the batteries into the tool.
e) Do not discharge the batteries by shortಣcircuit-
ing. This may cause them to overheat and present
a risk of personal injury (burns).
f) Do not attempt to open the batteries and do not
subject them to excessive mechanical stress.
en
5.6 Laser classification
Depending on the version purchased, the tool com-
plies with Laser Class 2 in accordance with IEC825ಣ
1:2003 / EN60825ಣ1:2003 and Class II in accordance
with CFR 21 § 1040 (FDA). This tool may be used
without need for further protective measures. The
eyelid closure reflex protects the eyes when a per-
son looks into the beam unintentionally for a brief
moment. This eyelid closure reflex, however, may be
negatively affected by medicines, alcohol or drugs.
Nevertheless, as with the sun, one should not look
directly into sources of bright light. Do not direct the
laser beam toward persons.
5.4 General safety rules
a) Check the condition of the tool before use. If the
tool is found to be damaged, have it repaired at
a Hilti service center.
b) The user must check the accuracy of the tool
after it has been dropped or subjected to other
mechanical stresses.
c) Although the tool is designed for the tough con-
ditions of jobsite use, as with other measuring
instruments it should be treated with care.
d) Although the tool is protected to prevent entry
of dampness, it should be wiped dry each time
before being put away in its transport container.
5.7 Transport
Always remove the batteries before shipping the
tool.
6. Before use
1. Unscrew the battery compartment cover from the
rear of the tool.
2. Remove the batteries from the packaging and
insert them in the tool.
NOTE Take care to observe correct polarity (see
symbols in battery compartment).
3. Check to ensure that the battery compartment
6.1 Inserting the batteries 2
CAUTION
Do not use damaged batteries.
cover is closed securely.
CAUTION
6.2 Switching the tool on / off
Always replace the complete set of batteries.
1. The tool can be switched on by pressing either
the “On / off” button or the “Measure” button.
DANGER
Do not mix old and new batteries. Do not mix
batteries of different makes or types.
24
2. When the tool is switched off, press the “On / off”
button: The tool switches on.
6.5 Measuring references
NOTE
The laser beam is switched off.
The tool can take measurements from 4 different
reference (contact) points. The “Reference” button
on the left on the front of the tool is used to switch
between the front and rear references (front or rear
edge of the tool). The reference is set automatically
to the tip of the spike when the spike is folded
out through 180°. When the measuring extension is
screwed into place, this is detected automatically by
the tool and indicated by the long extension symbol
in the display.
3. When the tool is switched on, press the “On / off”
button: The tool switches off.
4. When the tool is switched off, press the “Measure”
button: The tool and the laser beam switch on.
en
6.3 First distance measurements
1. Press the “Measure” button once.
If switched off, the tool will be switched on and
the laser beam activated.
If the tool is already switched on, the laser beam
will be activated.
2. Aim the tool by positioning the visible laser spot
on a white surface at a distance of approx. 3 ಣ 10
m.
3. Press the “Measure” button again.
The distance will be displayed in less than a
second, e.g. 5.489 m.
Front edge
Rear edge
Spike
You have just taken your first measurement with
the tool.
6.4 Settings menu
MENU
m
PDA 71 measuring extension: is detected automatic-
ally when screwed in.
1. With the tool switched off, press the “On / off”
button for approx. 2 seconds to enter menu mode.
2. Press the “Plus” button to switch the beep signal
on or off.
6.6 Measuring distances
NOTE
When the spike is folded back in, the measuring
reference is always reset to the rear edge of the tool
irrespective of how far the spike was folded out or to
which point on the tool the measuring reference was
previously set.
3. Press the “Minus” button repeatedly to scroll
through the choice of units.
4. Press the “On / off” button briefly to close the
menu.
The tool is switched off and all the settings shown
will be saved.
25
Distances can be measured from all stationary targets
withouta highlyreflectivesurface, i.e. concrete, stone,
wood, plastic, paper, etc. The use of prisms or other
highly reflective targets is not permissible and, if
attempted, may falsify the results.
6.6.1 Measuring distances step by step
NOTE
en
The range meter measures distances in a very short
time and simultaneously shows various information
in the display.
m
5.489
Switch the tool on by pressing the “On / off” button.
If further measurements are taken, up to three previ-
ously determined distances are shown in the interme-
diate result lines, i.e. a total of the last four measured
distances are shown.
m
m
m
5.489
12.349
24.634
m
----------
Press the “Measure” button once. The laser beam is
switched on and is visible in the form of a spot on the
target surface. This aiming mode is indicated in the
display by a blinking laser symbol.
27.317
m
The tool can, of course, be switched on again at any
time by pressing the “Measure” button. Pressing the
Cಣbutton clears all currently displayed values.
6.6.2 Measuring modes
Distances can be measured using two different meas-
uring modes, i.e. single distance measuring or con-
tinuous measuring. Continuous measuring mode is
used for setting out given distances or lengths and
can also be used where distance measurement is
otherwise difficult, e.g. at corners, edges or in niches,
etc.
m
----------
Aim at the target. Press the “Measure” button once
again to measure the distance. The result usually
appears in the result line in less than a second and
the laser beam then switches off.
26
1. Fold out the spike through 180°.
6.6.2.1 Single distance measuring (“Measure”
button)
1. Switch the laser beam on by pressing the “Meas-
ure” button.
2. Press the “Measure” button again.
The measured distance will be shown in the result
line at the bottom of the display in less than a
second.
The measuring reference is then set automatically
to the end of the spike. The range meter takes
the extended reference point into account and
corrects the measured distances accordingly.
2. Position the range meter with the spike at the
desired starting point for the measurement and
aim toward the target.
en
3. Press the “Measure” button.
The measured distance is shown in the display.
6.6.2.2 Single distance measuring (“On /off”
button)
1. Switch the laser beam on by pressing the “On /
off” button.
6.6.4 Measuring with the aid of target
objects 5 6
When taking measurements to outside corners (e.g.
on outside walls of buildings, perimeter fences, etc.),
boards, bricks or other suitable objects can be held
against the corner and used as the target. Use of
the PDA 50, PDA 51 or PDA 52 target plate is
recommended for long distances and in unfavorable
light conditions, e.g. in strong sunlight.
2. Press the “Measure” button to switch the laser
beam on and then aim the tool at the target.
3. Press the “Measure” button again.
The measured distance will be shown in the result
line at the bottom of the display in less than a
second.
6.6.2.3 Continuous measuring (tracking)
NOTE
Continuous measuring is possible in all situations
where individual distances can be measured. This
applies also to functions, such as areas.
6.6.5 Measuring in bright conditions
We recommend use of the PDA 50, PDA 51 or PDA 52
target plate for long distances and in very bright light
conditions.
6.6.6 Taking measurements to rough surfaces 7
1. Press the “Measure” button for about 2 seconds
to activate the continuous measuring mode.
NOTE When doing so, it doesn’t matter whether
the tool or the laser beam is switched on or
off. The tool will always switch to continuous
measuring mode.
When measuring to rough surfaces, e.g. rough plaster
etc., an average distance value is measured with the
center of the laser spot weighted higher than the
edges of the laser spot.
6.6.7 Taking measurements to curved or
inclined surfaces
During continuous measuring, distances are up-
dated in the result line at the rate of approx. 6 ಣ
10 measurements every second. The measuring
rate depends on reflectivity of the target surface.
If the beep signal is active, continuous measuring
is indicated by a beep signal approx. 2 ಣ 3 times
per second.
If the laser beam strikes the target surface at a very
narrow angle, the light reflected may be inadequate.
Conversely, too much light may be reflected toward
the tool in situations where the laser beam strikes
the target perpendicularly. We recommend use of the
PDA 50, PDA 51 or PDA 52 target plate in both of
these situations.
2. Measuring is stopped by pressing the “Measure”
button once again.
The last valid measurement is then shown in the
result line in the display.
6.6.8 Taking measurements to wet or shiny
surfaces
As long as the range meter can be aimed directly at
the surface, the distance to the target will be reliably
measured. With highly reflective surfaces, a reduction
6.6.3 Measuring from corners 3 4
The spike is used when measuring diagonally across
rooms or from inaccessible corners.
27
in range must be expected and the distance to the
actual point of reflection may be measured.
and when the target and/or the tool is shaded from
bright light.
Use of the PDA 50, PDA 51 or PDA 52 target plate
also increases the range of the tool.
6.6.9 Taking measurements to transparent
surfaces
6.6.10.2 Reduced measuring range
It is generally possible to measure distances to trans-
parent or semiಣtransparent materials, e.g. liquids,
polystyrene foam, etc. Light penetrates these mater-
ials, however, and measuring errors may therefore
occur. Measuring errors may also occur when meas-
urements are taken through glass or if objects are
present within the line of the laser beam.
Measuring range may be reduced in bright conditions,
e.g. in bright sunlight or when working under very
powerful floodlights.
The range of the tool may be reduced when meas-
urements are taken through glass or when objects lie
within the path of the laser beam.
en
The range of the tool may be reduced when measure-
ments are taken to mat green, blue or black surfaces
or to wet or shiny surfaces.
6.6.10 Measuring range
6.6.10.1 Increased range
The range of the tool is generally increased when
measurements are taken in the dark, at dawn or dusk
7. Operation
7.2 Adding distances
7.1 Distance measurements
NOTE
12.349
m
m
With all functions of the tool, each step in the opera-
tion is always indicated in the display.
+
5.489
NOTE
Continuous measuring mode can be used with all
functions in which individual distance measurement
is possible.
m
17.838
NOTE
Individual distances can be conveniently added. This
is useful, for example, for determining the total length
of the inner face of door or window openings or
If measuring errors occur during continuous meas-
uring, and continuous measuring mode is canceled
by pressing the “Measure” button again, the last valid
measurement will be displayed.
28
for adding several individual distances that form a 1. Press the “Measure” button (the laser beam
perimeter. switches on).
1. Press the “Measure” button (the laser beam will 2. Aim the range meter at the target.
switch on).
2. Aim the range meter at the target.
3. Press the “Measure” button.
3. Press the “Measure” button. The first distance
will be measured and displayed (the laser then
switches off).
4. Press the “Minus” button. The first distance is
then displayed in the middle result line and a
minus sign appears in the lower (intermediate)
result line (the laser beam switches on).
5. Aim the range meter at the target.
6. Press the “Measure” button.
The first distance will be measured and displayed
(the laser then switches off).
4. Press the “Plus” button. The first distance is then
displayed in the middle result line and a plus sign
appears in the lower (intermediate) result line (the
laser beam switches on).
en
5. Aim the range meter at the target.
6. Press the “Measure” button.
The second distance is then measured and dis-
played in the lower (intermediate) result line.
The result of the subtraction is shown in the result
line.
The current difference in distance is always shown
in the result line.
The second distance is then measured and dis-
played in the lower (intermediate) result line. The
result of the addition is shown in the result line.
The current total of the distances is always shown
in the result line.
The procedure can be repeated until all distances
have been subtracted.
The procedure can be repeated until all distances
have been added.
7. To terminate the subtraction of distances, simply
measure a distance without first pressing the
“Minus” button.
All previous measuring and calculation results are
shown in the intermediate results lines.
8. Press the Cಣbutton to clear the display.
7. To terminate the addition of distances, simply
measure a distance without first pressing the
“Plus” button.
All previous measuring and calculation results are
shown in the intermediate results lines.
8. Press the Cಣbutton to clear the display.
7.4 Measuring areas
7.3 Subtracting distances
3.947
m
m
-
3.322
2
m
0.625
Each step of the area measurement operation is
indicated graphically in the display. For example,
to determine the floor area of a room, proceed as
follows:
Individual distances can be conveniently subtracted
from each other, e.g. in order to determine the dis-
tance between the underside of a pipe and the ceiling.
This can be done by subtracting the distance between 1. Press the “Area” button to activate area measuring
the floor and the underside of the pipe from the
distance between the floor and the ceiling. If the
pipe diameter is subtracted, the result is the distance
between the top of the pipe and the ceiling.
mode.
NOTE When the area function is activated, the
laser beam is already switched on.
29
2. Aim the range meter at the target.
3. Press the “Measure” button.
6. The Cಣbutton can be pressed at any time to
stop the measuring operation. Each measurement
can then be cleared, one after the other, and
measuring restarted.
For example, to determine the floor area of a
room, proceed as follows:.
NOTE If the Cಣbutton is pressed several times
or the FNCಣbutton is pressed, the function will be
canceled or, respectively, restarted.
NOTE If the second distance is measured using
continuous measuring mode (tracking), the result
of the area calculation is updated continuously.
This allows parts of the area to be included/
excluded.
The graphic display automatically prompts you to
measure the length of the room.
4. Aim the tool at the next target to obtain the length
of the room.
5. Press the “Measure” button.
en
The second distance is then measured, the area
calculated immediately and the result is displayed
in the result line.
NOTE After calculation of an area, the “Plus”
button can be pressed to add another area or,
respectively, the “Minus” button used to subtract
an area.
Both distances used for the area calculation are
shown in the intermediate result lines and can
be noted down conveniently at the end of the
operation.
8. Care and maintenance
8.1 Cleaning and drying
1. Blow dust off the lenses.
8.4 Calibration and adjustment
8.4.1 Calibration
2. Do not touch the glass or the filter with the fingers.
3. Use only a clean, soft cloth for cleaning. If neces-
sary, moisten the cloth slightly with pure alcohol
or a little water.
NOTE Do not use any other liquids as these may
damage the plastic components.
4. The temperature limits for storage of your equip-
ment must be observed, especially in winter /
summer.
Monitoring of measuring equipment for users cer-
tified in accordance with ISO 9000X: As specified
in ISO 900X, you may carry out the inspection and
testing of the PD 40 laser range meter yourself (see
ISO 17123ಣ4: Field Process for Accuracy Examination
of Geodetic Instruments: Part 6, Closeಣrange Optoಣ
electrical Range Meters).
1. Select a readily accessible measuring distance of
a known length (approx. 1 to 5 meters / 3 to
15 feet) which does not change over time and
measure the same distance 10 times.
8.2 Storage
Remove the tool from its case if it has become wet. 2. Determine the mean deviation from the known
The tool, its carrying case and accessories should
be cleaned and dried (at maximum 40°C / 104°F).
Repack the equipment only once it is completely dry.
Check the accuracy of the equipment before it is used
after a long period of storage or transportation.
Remove the batteries from the tool before storing it
for a long period. Leaking batteries may damage the
tool.
distance. This value should be within the specified
accuracy tolerance for the tool.
3. Keep a record of this value and note the date when
the next test is due.
Repeat this test at regular intervals as well as
before and after important measuring tasks.
Apply a test and inspection confirmation sticker
to the PD 40 and keep a record of the entire
monitoring, test and inspection procedure and
the results.
8.3 Transport
Please refer to the technical data contained in
the operating instructions and the information
concerning measuring accuracy.
Use the Hilti toolbox or packaging of equivalent quality
for transporting or shipping your equipment.
CAUTION
Always remove the batteries before shipping the
tool.
30
8.4.2 Adjustment
The calibration service provides confirmation that the
tool is in conformance, on the day it is tested, with
the specifications given in the operating instructions.
The tool will be readjusted if deviations from the
manufacturer’s specification are found. After check-
ing and adjustment, a calibration sticker applied to
the tool and a calibration certificate provide written
verification that the tool operates in accordance with
the manufacturer’s specification.
Calibration certificates are always required by com-
panies certified according to ISO 900x.
Your local Hilti Center or representative will be pleased
to provide further information.
To ensure that the laser range meter is adjusted
correctly, we recommend that it is returned to a Hilti
Service Center for calibration. Accurate adjustment of
the tool will be confirmed by a calibration certificate.
8.4.3 Hilti calibration service
en
We recommend that the tool is checked by the Hilti
calibration service at regular intervals in order to
verify its reliability in accordance with standards and
legal requirements.
Use can be made of the Hilti calibration service
at any time, but checking at least once a year is
recommended.
9. Troubleshooting
Fault
Possible cause
Remedy
The tool can’t be switched on. The batteries are exhausted.
Incorrect battery polarity.
Replace the batteries.
Insert the batteries correctly and
close the battery compartment
cover.
The button is faulty.
Return the tool to Hilti for repair.
No distances displayed by the
tool.
“Measure” button was not pressed. Press the “Measure” button.
Faulty display.
Return the tool to Hilti for repair.
Frequent error messages or
the tool doesn’t measure.
The target surface is too brightly lit Measure from the other direction –
by the sun.
sun from behind.
The target surface is too shiny.
Take measurements from less shiny
surfaces.
Use the PDA 50/ PDA 51/ PDA 52
target plate.
Use the PDA 50/ PDA 51/ PDA 52
target plate.
The target surface is too dark.
Bright sunlight towards the tool.
Measuring reference not set
to the spike.
The spike is not folded out fully.
The spike is faulty.
Fold the spike out fully.
Return the tool to Hilti for repair.
The measuring extension is not
screwed in fully.
Measuring reference not set
to the extension.
Screw the measuring extension in
fully.
Dirt or foreign matter in the threaded Clean the threaded bush.
bush.
No result obtained using
functions.
Distance measurements are miss- Measure the missing distance(s).
ing.
Numerical value of the result is too Change to a larger unit.
high (cannot be displayed).
31
10. Disposal
WARNING
Improper disposal of the equipment may have serious consequences:
The burning of plastic components generates toxic fumes which may present a health hazard.
Batteries may explode if damaged or exposed to very high temperatures, causing poisoning, burns, acid burns
or environmental pollution.
en
Careless disposal may permit unauthorized and improper use of the equipment. This may result in serious
personal injury, injury to third parties and pollution of the environment.
Most of the materials from which Hilti tools or appliances are manufactured can be recycled. The materials must
be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements
for taking back old tools and appliances for recycling. Ask Hilti customer service or your Hilti representative
for further information.
For EC countries only
Disposal of electric tools together with household waste is not permissible.
In observance of European Directive 2002/96/EC on waste electrical and electronic equipment
and its implementation in accordance with national law, electric tools that have reached the end
of their life must be collected separately and returned to an environmentally compatible recycling
facility.
Dispose of the batteries in accordance with national regulations.
11. Manufacturer’s warranty ಣ tools
Hilti warrants that the tool supplied is free of defects
in material and workmanship. This warranty is valid
so long as the tool is operated and handled correctly,
cleaned and serviced properly and in accordance with
the Hilti Operating Instructions, and the technical
system is maintained. This means that only original
Hilti consumables, components and spare parts may
be used in the tool.
Additional claims areexcluded, unlessstringent na-
tional rules prohibit such exclusion. In particular,
Hilti is not obligated for direct, indirect, incidental
or consequential damages, losses or expenses in
connection with, or by reason of, the use of, or
inability to use the tool for any purpose. Implied
warranties of merchantability or fitness for a par-
ticular purpose are specifically excluded.
This warranty provides the freeಣofಣcharge repair or
replacement of defective parts only over the entire
lifespan of the tool. Parts requiring repair or replace-
ment as a result of normal wear and tear are not
covered by this warranty.
For repair or replacement, send the tool or related
parts immediately upon discovery of the defect to
the address of the local Hilti marketing organization
provided.
This constitutes Hilti’s entire obligation with regard
to warranty and supersedes all prior or contempor-
aneous comments and oral or written agreements
concerning warranties.
32
12. EC declaration of conformity
Hilti Corporation
Designation:
Type:
Laser range meter
PD 40
2006
Year of design:
We declare, on our sole responsibility, that this
product complies with the following directives and
standards: EN 50081ತ1, EN 61000ತ6ತ2, 89/336/EEC.
en
Bodo Baur
Tassilo Deinzer
Head BU Measuring Systems
BU Measuring Systems
01 2007
Quality Manager
BA Electric Tools & Accessories
01 2007
33
Hilti Corporation
LI-9494 Schaan
Tel.: +423 /2342111
Fax: +423 /2342965
Hilti = registered trademark of Hilti Corp., Schaan W 3279 0307 00-Pos. 2
Right of technical and programme changes reserved S. E. & O.
1
Printed in Liechtenstein © 2007
320291 / B
|