Revision 1.3ꢀ
July 2001ꢀ
Contents
1.
INTRODUCTION ...............................................................................................................................................1ꢀ
1.1 CONVENTIONS ...................................................................................................................................................1ꢀ
1.2 ARGUMENT TYPES.............................................................................................................................................1ꢀ
1.3 PRIVILEGE AND CONTEXT LEVELS.....................................................................................................................2ꢀ
1.4 THE COMMAND LINE INTERFACE......................................................................................................................3ꢀ
1.5 SYSTEM HELP ....................................................................................................................................................3ꢀ
1.6 COMMAND LINE EDITING..................................................................................................................................4ꢀ
2.
COMMAND SUMMARY...................................................................................................................................5ꢀ
2.1 USER EXEC COMMANDS ..................................................................................................................................5ꢀ
2.2 DIAGNOSTIC COMMANDS ..................................................................................................................................6ꢀ
2.3 SYSTEM CONFIGURATION................................................................................................................................11ꢀ
2.3.1
2.3.2
System commands - EXEC level............................................................................................................11ꢀ
System Configuration commands..........................................................................................................14ꢀ
2.4 AUTHENTICATION .....................................................................................................................................16ꢀ
2.4.1 AUTHENTICATION commands - Configuration level.........................................................................16ꢀ
2.5 TACACS.........................................................................................................................................................17ꢀ
2.5.1
2.5.2
TACACS commands - EXEC level ........................................................................................................17ꢀ
TACACS commands - Configuration level ...........................................................................................17ꢀ
2.6 CDP.................................................................................................................................................................17ꢀ
2.6.1
2.6.2
CDP commands - EXEC level...............................................................................................................17ꢀ
CDP commands - Configuration level..................................................................................................17ꢀ
2.7 IP STACKING ...................................................................................................................................................18ꢀ
2.7.1
2.7.2
IP Stacking commands - EXEC level ....................................................................................................18ꢀ
IP Stacking commands - Configuration level .......................................................................................18ꢀ
2.8 PORT SETTINGS ...............................................................................................................................................20ꢀ
2.8.1
2.8.2
Port commands - EXEC level................................................................................................................20ꢀ
Ethernet Interface Configuration Commands.......................................................................................22ꢀ
2.9 TRUNK CONFIGURATION .................................................................................................................................23ꢀ
2.9.1
2.9.2
2.10
Trunk commands - EXEC level .............................................................................................................23ꢀ
Trunk commands - Configuration level ................................................................................................24ꢀ
SPANNING TREE..........................................................................................................................................25ꢀ
2.10.1 Spanning Tree commands - EXEC level ...............................................................................................25ꢀ
2.10.2 Spanning Tree commands - Configuration level ..................................................................................26ꢀ
2.11
IP ................................................................................................................................................................28ꢀ
2.11.1 IP commands - EXEC level...................................................................................................................28ꢀ
2.11.2 IP commands - Configuration level ......................................................................................................31ꢀ
2.11.3 IP commands - VLAN Interface level....................................................................................................33ꢀ
2.12
SNMP.........................................................................................................................................................34ꢀ
2.12.1 SNMP commands - EXEC level ............................................................................................................34ꢀ
2.12.2 SNMP commands – Configuration Level..............................................................................................35ꢀ
2.13
VLAN CONFIGURATION.............................................................................................................................36ꢀ
2.13.1 VLAN commands - EXEC level.............................................................................................................36ꢀ
2.13.2 VLAN commands – Configuration Level ..............................................................................................36ꢀ
2.13.3 VLAN Interface commands ...................................................................................................................37ꢀ
2.14
GVRP.........................................................................................................................................................38ꢀ
2.14.1 GVRP commands - EXEC level.............................................................................................................38ꢀ
2.14.2 GVRP commands – Configuration level...............................................................................................38ꢀ
2.14.3 Ethernet Interface Configuration commands........................................................................................38ꢀ
2.15
IGMP..........................................................................................................................................................39ꢀ
2.15.1 IGMP Commands – EXEC Level.........................................................................................................39ꢀ
2.15.2 IGMP Configuration commands – Vlan Interface level .......................................................................40ꢀ
2.16
PORT MONITORING.....................................................................................................................................41ꢀ
2.16.1 Port Monitoring commands - EXEC level ............................................................................................41ꢀ
2.16.2 Port Monitoring commands - Configuration level................................................................................41ꢀ
2.16.3 Port Monitoring commands - VLAN Interface level............................................................................42ꢀ
2.16.4 Port Monitoring commands - Ethernet Interface level........................................................................42ꢀ
2.17
PORT SECURITY ..........................................................................................................................................42ꢀ
2.17.1 Port Security commands - EXEC level .................................................................................................42ꢀ
2.17.2 Port Security commands - Configuration level.....................................................................................43ꢀ
3.
CONSOLE MENU.............................................................................................................................................45ꢀ
3.1 STATUS AND COUNTERS..................................................................................................................................45ꢀ
3.1.1
3.1.2
3.1.3
3.1.4
3.1.5
General System Information .................................................................................................................46ꢀ
Management Address Information........................................................................................................46ꢀ
Module Information ..............................................................................................................................47ꢀ
Port Status.............................................................................................................................................47ꢀ
Port Counters........................................................................................................................................48ꢀ
3.1.5.1 Port Counters Details.........................................................................................................................................48ꢀ
3.1.6
Address Table........................................................................................................................................49ꢀ
Port Address Table................................................................................................................................49ꢀ
Spanning Tree Information ...................................................................................................................50ꢀ
3.1.7
3.1.8
3.1.8.1 Spanning Tree Port Information........................................................................................................................50ꢀ
3.2 CONFIGURATION MENU...................................................................................................................................51ꢀ
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
3.2.6
3.2.7
3.2.8
System Information................................................................................................................................52ꢀ
Port/Trunk Settings ...............................................................................................................................52ꢀ
Network Monitoring Port......................................................................................................................53ꢀ
Spanning Tree Operation......................................................................................................................53ꢀ
IP Configuration ...................................................................................................................................54ꢀ
SNMP Communities ..............................................................................................................................55ꢀ
Authorized Managers............................................................................................................................55ꢀ
VLAN Menu...........................................................................................................................................56ꢀ
3.2.8.1 VLAN Support ..................................................................................................................................................56ꢀ
3.2.8.2 VLAN Names....................................................................................................................................................57ꢀ
3.2.8.3 VLAN Port Assignment....................................................................................................................................57ꢀ
3.3 PASSWORD MENU............................................................................................................................................58ꢀ
3.4 EVENT LOG......................................................................................................................................................58ꢀ
3.5 DOWNLOAD SCREEN .......................................................................................................................................59ꢀ
3.6 RUN SETUP ......................................................................................................................................................59ꢀ
1.
Introduction
This document provides a summary of the commands supported on the HP ProCurve 2524,
2512, and 4108gl switches. It is divided into sections that correspond to different modules or
features of the HP switches. Not all sections will apply to all HP switches since each switch
may only support a subset of the total feature set that is described in this document.
1.1 Conventions
Command descriptions use the following conventions:
ꢀ Vertical bars “|” separate alternative, mutually exclusive elements.
ꢀ Square brackets “[ ]” indicate optional elements.
ꢀ Braces “<>” indicate a required choice.
ꢀ Braces within square brackets “[<>]” indicate a required choice within an optional
element.
ꢀ Boldface indicates commands and keywords that are entered literally as shown.
ꢀ Italics indicates arguments for which you must supply a value.
ꢀ If the no form of a command has exactly the same keywords and arguments as the
command, then no appears in square brackets at the beginning of the command.
Otherwise, the no form of the command is described separately.
ꢀ If the no form of a command is not explicitly described, then it simply negates the
command. For example, if the command enables a feature, then the no form of the
command would disable it. Also, if the a command was used to add a configuration item,
then the no form of the command would remove it.
1.2 Argument Types
The following argument types are recognized by the CLI and are used in the command
syntax throughout this document:
ꢀ mac-addr – For example, 0060b0-885a80 or 0060b0:885a80.
ꢀ ip-addr - IP address in dotted decimal notation. For example, 10.0.16.80
ꢀ ip-mask - This is syntactically expressed the same way as ip-addr.
ꢀ port-number - Devices with fixed port configurations accept port numbers
specified as integers. Modular devices accept port numbers specified with slot
and port number identifiers. For instance, port "A1" indicates Port 1 in Slot A.
1ꢀ
There are three "special" port designations in the switch. You may specify the
monitoring port by using "mp"; you may specify a trunk port by using "trkX",
where X identifies the numerical trunk group.
ꢀ port-list - A port list specifies a group of ports for which the operation being
performed should be applied. A port list consists of individual port identifiers or
ranges of ports separated by commas (e.g., A1-B8, C4, D1). This list includes the
"special" port designations described under port-number.
ꢀ vlan-id - The 802.1Q VLAN identifier.
1.3 Privilege and Context levels
The new CLI will support two privilege levels (operator and manager) and several context
levels. As each context level is entered, the context information is displayed as part of the
command prompt. When a context specific command is executed, the context information
is applied to the particular command. For instance, when you attempt to enter the interface
context level, you must specify a port number (see interface ethernet). Subsequent
commands that affect port behavior (e.g., flow-control) will be applied to the port number
specified when entering the level, so the specified port need not be re-specified on the
command line.
EXEC level
HP 4108GL>
Global configuration level
HP 4108GL(config)
interface config level
HP 4108GL(if-A1)
vlan config level
HP 4108GL(vlan-1)
Figure 1: Command and context levels
When you log onto the switch, you will be placed at the operator EXEC level and the
system will display the following prompt:
HP 4108GL>ꢀ
2ꢀ
If an operator password has been set (see password in the global configuration section),
then the system would have displayed the following prompt before entering the operator
EXEC level:
Password:ꢀ
You can enter the manager EXEC level from the operator EXEC level by using the enable
command. If a manager level password has been configured, then you will be prompted for
the manager password after executing the enable command.
1.4 The Command Line Interface
The new CLI will not be case sensitive. As a short cut, you can abbreviate commands and
keywords as long they contain enough letters to be distinguished from any other currently
available commands or keywords.
When the command text exceeds the length of the command line, the current command line
will scroll upwards, yet the cursor will shift to the first character on the last line on the
screen. This is opposed to shifting the command line horizontally each time the command
exceeds the number of characters that can be displayed at one time on the screen.
1.5 System Help
You can enter help or ? at a particular command level to see the commands available at that
level. You can enter a command followed by help or ? in order to get the system to display
the command description for that particular command. The command description would be
similar to what is presented for each command in the Command Reference section of this
document.
In order to see the list of possible word completions or to complete the current word, you
may use the Tab key immediately after the last letter of the last keyword on the command
line. For example, if the system was currently in the global configuration level and you typed
tab immediately after the t in step (1), the system would display the options seen in section
(2) and the system would return to the configuration level prompt with the partially
completed command line seen in (3):
(1) HP 4108GL(config) tꢀ
(2) trunkꢀ
trapꢀ
trap-send-authenticationꢀ
telnet-serverꢀ
(3) HP 4108GL(config)tꢀ
3ꢀ
If you had already typed in trap- on line (1) and then pressed the tab character, the system
would complete the keyword trap-send-authentication, for it is the only possible
completion for trap-, and display the completed command line as shown below:
1. HP 4108GL(config) trap-
2. HP 4108GL(config) trap-send-authentication
1.6 Command Line Editing
Before you press return, the current command line can be edited using special keys
including arrows and control characters. The following table describes the supported
command editing keys and their function:
Keystroke
Function
Jumps to the first character of the command line.
Moves the cursor back one character.
Ctrl-A
Ctrl-B; left arrow
Ctrl-C
Escapes and terminates prompts and lengthy tasks.
Deletes the character at the cursor.
Ctrl-D
Ctrl-E
Jumps to the end of the current command line.
Moves the cursor forward one character.
Deletes from the cursor to the end of the command line.
Repeats current command line on a new line.
Enters next command line in the history buffer.
Enters previous command line in the history buffer.
Deletes from the cursor to the beginning of the command line.
Deletes last word typed.
Ctrl-F; right arrow
Ctrl-K
Ctrl-L; Ctrl-R
Ctrl-N; down arrow
Ctrl-P; up arrow
Ctrl-U; Ctrl-X
Ctrl-W
Esc B
Moves the cursor backward one word.
Esc D
Deletes from the cursor to the end of the word.
Moves the cursor forward one word.
Esc F
Erases mistake when entering a command; reenter command after using this
key.
Delete; Backspace
4ꢀ
2.
Command Summary
2.1 User EXEC Commands
enable
Enters the manager EXEC level. If a manager password is set, the system will first
prompt for the password. Echoing is disabled while you enter the password. Initially
there are no passwords for the two levels of users in the system: manager and
operator. When you first connect to the console or telnet into the system, you will be
placed into the Operator EXEC level. At that time, you can enter the above enable
command without a password in order to be granted manager access to the switch
and to be placed into the manager EXEC level. Passwords are set and changed
through the password command at the global configuration level.
configure [terminal]
Used to enter the global configuration level.
end
This command sets the current command or context level to the manager EXEC
level.
exit
This command sets the current command level to the previous command level. At
the operator EXEC level, this command acts the same as logout.
interface [ethernet] <port-list>
Enters the Ethernet interface configuration context for the port-list.
logout
Terminates this console/telnet session.
menu
Used to enter the menu system. For more information, see the Console Menu
section of this document.
setup
Used to setup initial switch configuration.
5ꢀ
[no] page
Toggles the paging mode for display commands so that the “—more –“ will appear
or not appear.
repeat
Repeatedly executes the previous command until a key is pressed.
vlan <vlan-name | vlan-id>
Enters the VLAN interface configuration context for the VLAN.
2.2 Diagnostic Commands
boot [system [flash <primary|secondary>]]
Performs cold reboot of switch.
write terminal
This command displays the running configuration.
write memory
This command saves the running configuration to Flash.
erase startup-config
Deletes the configuration stored in flash so that the switch will reverted to it’s
default configuration upon reboot.
erase flash <primary|secondary>
Deletes the configuration stored in flash so that the switch will reverted to it’s
default configuration upon reboot.
copy tftp <startup-config|flash> <ip-addr> <remote-file>
[primary|secondary]
Retrieves a configuration or OS file on the remote host, and overwrites the switch's
corresponding file with the remote file.
6ꢀ
copy <startup-config|running-config|crash-log|event-log|crash-rec|Command>
tftp <ip-addr> <remote-file>
This command writes the switch's configuration file, crashrec, eventlog or the output
from a command specified by Command to the remote file on the remote host.
show startup-config
Displays the configuration stored in flash.
show running-config
Displays the configuration stored in flash.
show boot-history
Displays the switch shutdown history.
kill
This command kills all other active sessions.
show logging [-a] [<search-text>]
Displays the switch's event log. If -a is specified then entire internal switch log is
displayed. If search-text is specified then only events that contain that text are
displayed.
print <command>
Used to execute a command and captures its output using a terminal emulator. This
command will display “Press RETURN when ready…” to allow the terminal
emulator to be set up to for the capture and “Press RETURN when done…” once
the output is complete.
show history
Displays the current command history.
reload
Performs a warm reboot.
clear arp
To clear the arp cache of all non-permanent entries.
7ꢀ
clear intrusion-log
To clear the intrusion log.
clear statistics [ethernet] <port-list>
To reset counters displayed by the console. If a new console session is initiated, the
counters will revert back to the values maintained by the switch hardware.
telnet <ip-addr>
To initiate a telnet session with another network device.
telnet <0..15>
To initiate a telnet session to a member switch in the stack.
Parameters:ꢀ
ꢀ <0..15> specifies the number of the switch to be contacted.ꢀ
getmib <object-name> [<object-name> …]
Retrieves and displays the MIB object defined by object-name.
walkmib <object-name>
This command shows a group of managed object values.
8ꢀ
setmib <object-name> <type> <value> [<object-name> <type> <value> …]
This command sets the MIB object defined by object-name. The options for the type
parameter are case sensitive as shown below:
-i
Integer
-o
-d
-a
Octet string
Object identifier
IP address (nnn.nnn.nnn.nnn)
Counter
-c
-g
-t
Gauge
Time tick
-u
-D
-N
Unsigned integer
Display string (“value”)
Null
show version
Displays software version information.
show flash
Displays software version information for images in flash.
show tech
Displays switch information needed by HP support for diagnostics.
copy xmodem < startup-config |flash [primary|secondary]>
Retrieves a configuration file using the Xmodem protocol and then writes the
retrieved file to the switch's flash.
copy <startup-config|running-config|crash-log|event-log|crash-rec|Command>
xmodem [ pc | unix ]
Writes either the configuration file, crashrec, eventlog, or the output from a
command specified by command using the Xmodem protocol.
9ꢀ
link-test <mac-addr> [vlan <vlan-id>] [repetitions <1..999>] [timeout <1..256>]
Tests the connection to a MAC station on the LAN by sending a 802.2 test packet to
a specific target node on a network directly attached to a port in that LAN. The
target node must be able to respond to this test packet with an 802.2 Test Response
packet in order for the test to work. The switch produces the following output if the
link test succeeds:
link-test passedꢀ
otherwise, the following is displayed:
link-test failedꢀ
Parameters:
ꢀ <mac-addr> - MAC address of the station to send link test to.
ꢀ vlan <vlan-id> - Expected VLAN on which the station is expected to be present.
If this argument is not present then the VLAN used is 1.
ꢀ repetitions <1..9999> - Number of test packets to send; the default value is 1.
ꢀ timeout <1..256> - Seconds within which a response is required before the test
is considered as failed; the default value is 5.
ping <ip-addr> [repetitions <1..999>] [timeout <1..256>]
Issues an IP Ping requests to an IP device on the network and the system displays
the following output at the CLI if a response is received from the specified IP
address:
192.32.36.75 is alive, time = 10 msꢀ
If no response is received the system displays the following:
Target did not respondꢀ
Parameters:
ꢀ <ip-addr> - Network IP address of station to send IP Ping to.
ꢀ repetitions <1..999>- Number of times to send IP Ping; the default value is 1.
ꢀ timeout <1..256> - Seconds within which a response is required before the test
is considered as failed; the default value is 5.
10ꢀ
2.3 System Configuration
2.3.1 System commands - EXEC level
show console
Displays the console parameters.
Output Format:
Switch Configuration - Console/Serial Linkꢀ
Inbound Telnet Enabled [Yes] : Yesꢀ
Web Agent Enabled [Yes] : Yesꢀ
Terminal Type [VT100] : VT100ꢀ
Screen Refresh Interval (sec) [3] : 3ꢀ
Displayed Events [All] : Allꢀ
Baud Rate [Speed Sense] : Speed Senseꢀ
Flow Control [XON/XOFF] : XON/XOFFꢀ
Connection Inactivity Time (min) [0] : 0ꢀ
show mac-address [vlan <vlan-id>]
Displays the MAC addresses that the switch has learned from the network devices
attached to the switch, and the port on which each address was learned. If no vlan is
specified, then all MAC addresses that are know to the switch are shown.
Output Format:
Status and Counters - Address Tableꢀ
MAC Address Located on Portꢀ
-------------ꢀ ---------------
00105a-8abed4 1ꢀ
00105a-cac0e8 1ꢀ
0060b0-881c00 1ꢀ
009004-8e3178 1ꢀ
00c0f0-1c65ee 1ꢀ
00c0f0-30d74a 1ꢀ
080009-3515f9 1ꢀ
080009-782368 1ꢀ
080009-7b8cc4 1ꢀ
080009-919b30 1ꢀ
080009-959e2c 1ꢀ
11ꢀ
show mac-address <port-list>
Displays the MAC addresses that the switch has learned from the network devices
attached to the specified switch port.
Output Format:
Status and Counters - Port Address Table - Port 1ꢀ
MAC Addressꢀ
-------------ꢀ
00105a-8abed4ꢀ
00105a-cac0e8ꢀ
009004-8e3178ꢀ
00c0f0-1c65eeꢀ
00c0f0-1c66eaꢀ
00c0f0-30d74aꢀ
080009-3515f9ꢀ
080009-782368ꢀ
080009-7b8cc4ꢀ
080009-919b30ꢀ
080009-959e2cꢀ
show management
Displays configured addresses that are used to manage the switch.
Output Format:
Status and Counters - Management Address Informationꢀ
Time Server Address :ꢀ
MAC Address
IP Address
: 0060b0-885a80ꢀ
: 192.32.36.96ꢀ
IPX Network Number :ꢀ
12ꢀ
show modules
Displays the modules that are present on the switch.
Output Format:
Status and Counters - Module Informationꢀ
Module Type Module Descriptionꢀ
Slot
----ꢀ --------------- --------------------------------------------
A
Slot Availableꢀ
show system-information
Displays the status of and current configuration of all the switch internal resources.
Output Format:
System Informationꢀ
..System Name
System Contact
System Location
:ꢀ
:ꢀ
:ꢀ
Address Age Interval (min) [5] : 5ꢀ
Time Zone [0] : 0ꢀ
Daylight Time Rule [None] : User definedꢀ
Beginning month [April] : April ꢀ
Beginning day [1] : 1ꢀ
Ending month [October] : October ꢀ
Ending day [1]
: 1ꢀ
Firmware revision : C.08.XX ꢀ
Base MAC Addr
Serial Number
: 0060b0-885a80ꢀ
: +ꢀ
ROM Version
: C.05.X1 ꢀ
Up Time
: 17 hours ꢀ
Memory - Total : 7,669,088ꢀ
CPU Util (%)
: 2 ꢀ
Free : 4,871,840ꢀ
IP Mgmt - Pkts Rx : 14,496 ꢀ
Packet - Total : 462ꢀ
Buffers ꢀ Free : 296ꢀ
Lowest : 237ꢀ
Pkts Tx : 9463 ꢀ
Missed : 0ꢀ
13ꢀ
2.3.2 System Configuration commands
mac-age-time <1..100000>
Sets the number of seconds a MAC address stays in the switch address table before
being aged out. Aging out occurs if traffic isn't received from that MAC station
within the age interval. The default value is 300.
console [terminal <vt100 | ansi> [screen-refresh <value>] [events <none | all | non-
info | critical | debug>] [baud-rate <value>] [flow-control <xon/xoff | none>]
[inactivity <value>]
Sets the console parameters.
Parameters:
ꢀ terminal <vt100 | ansi> - Type of terminal being used (default is vt100).
ꢀ screen-refresh <1|3|5|10|20|30|45|60> - Sets the number of seconds before a
refresh is done on the “Status and Counters” screens (default is 3).
ꢀ events <none | all | non-info | critical | debug>] – The level of Switch events
displayed in Events Log. all - display all; none - display no events; not-info - display
all events except informational-only; critical - display only critical-level events;
debug (reserved for Internal use only).
ꢀ baud-rate <speed-sense | 1200 | 2400 | 4800 | 9600 | 19200 | 38400 | 57600
| 115200>] - Sets the data transmission speed for switch connect sessions initiated
through the Console port. Default is speed-sense.
ꢀ flow-control <xon/xoff | none> - Flow Control Method; default is xon-xoff.
ꢀ inactivity-timer <0 | 1 | 5 | 10 | 15 | 20 | 30 | 60 | 120> - Sets the number of
minutes of inactivity allowed by the switch before the switch will terminate the
communication session. 0 means never terminate the session; default is 0 .
[no] auto-tftp <ip-addr filename>
Enables/disables automatic OS image download via TFTP.
14ꢀ
time [mm/dd/yy] [hh:mm:ss] [timezone <value>] [daylight-time-rule <value>] [begin-date
<mm/dd> end-date <mm/dd>]
This command display switch's date & time or optionally sets it.
Parameters:
ꢀ timezone <-1440..1440> - Sets the number of minutes your location is to the
West(+) or East(-) of GMT (default is 0).
ꢀ daylight-time-rule <alaska | none | continental-us-canada | middle-europe-
and-portugal | southern-hemisphere | western-europe | user-defined> -
Sets the daylight savings time rule for your location. None (default) means that no
time adjustment will be made.
ꢀ begin-date <mm/dd> end-date <mm/dd > - begin-date and end-date are only
valid if the daylight time rule is set to user-defined.
snmp-server [contact <sys-contact>] [location sys-location>]
Sets the switch contact and location for administrative purposes.
Parameters:
ꢀ contact <sys-contact> - Up to 48 characters. Name of the switch administrator.
ꢀ location <sys-location> - Up to 48 characters. Description of the switch location.
hostname <name-string>
Sets the switch name for administrative purposes.
15ꢀ
[no] telnet-server
Enables remote telnet access to the switch.
[no] web-management
Enables the web browser to interact with the web agent on the switch.
[no] password <operator | manager>
Sets passwords for different classes of users. This command causes the switch to
prompt for a password twice, once for the new password and once to verify it was
typed correctly, and disables echoing while you type the password.
Parameters:
ꢀ <operator | manager> - Class of user.
2.4 AUTHENTICATION
2.4.1 AUTHENTICATION commands - Configuration level
aaa authentication console <enable|login>
<primary-method> [<backup-method>]
Configures authentication mechanism used to control access to the switch.
aaa authentication telnet <enable|login>
<primary-method> [<backup-method>]
Configures authentication mechanism used to control access to the switch.
16ꢀ
2.5 TACACSꢀ
2.5.1 TACACS commands - EXEC levelꢀ
show tacacsꢀ
Displays TACACS configuration.
2.5.2 TACACS commands - Configuration level
[no] tacacs-server host <ip-addr> [key <key-string>]
Configures a TACACS server.
tacacs-server timeout <1-255>
Sets up the TACACS timeout interval in seconds.
2.6 CDP
2.6.1 CDP commands - EXEC level
show cdp [neighbor [port-num] [detail]]
Displays CDP configuration and neigbors discovered.
2.6.2 CDP commands - Configuration level
[no] cdp
Enables/disables CDP on the switch.
cdp timer <5-254>
Sets the CDP transimit interval in seconds.
cdp holdtime <10-255>
Sets the CDP holdtime in seconds.
cdp enable [ethernet] <port-list>
Enables/disables CDP on a particular port.
17ꢀ
2.7 IP Stacking
2.7.1 IP Stacking commands - EXEC level
show stack [candidates | all]
Displays status information for the stacking feature. ‘show stack’ with no arguments
displays the status of this switch’s stack. If the keyword candidates is supplied then
this command displays a list of candidates on the local network segment. If the
keyword all is supplied then this command displays all the member switches of all
stacks on the local network segment and all candidate switches.
2.7.2 IP Stacking commands - Configuration level
[no] stack
Enables/disables the stacking feature. If the stacking features is disabled, then the
switch will reject a join request originating from a command switch.
[no] stack commander <commander-name>
Creates a command switch, and the no form of the command disperses the member
switches from this command switch’s stack, making them available to join another
stack.
[no] stack member <switch-num> mac-address <mac-addr> [password <password-str>]
Configures the candidate switch identified by the MAC address to be a member for
this switch’s stack. The no form of the command removes the switch identified by
switch-num from the stack
Parameters:
ꢀ <switch-num> - A number between 1 and 15 to uniquely identify each switch; a
switch-num of zero always belongs to the command switch.
ꢀ password <password-str> - is the manager password configured on the candidate
switch. If the candidate switch does not have a manager password then none
should be supplied.
[no] stack join <mac-addr>
Causes a candidate switch to join the stack whose command switch is identified by
mac-addr. The no form of the command causes the member switch to leave its
current stack.
18ꢀ
[no] stack auto-join
Causes the switch to advertise, via the discovery protocol, that it wants to
automatically join any stack operating on the local LAN segment. Switches with
passwords will not auto-join.
[no] stack auto-grab
Enables/disables auto-grab mode for stacking on the command switch. If enabled,
the command switch will attempt to grab new candidate switches and make them
members of the stack.
stack transmission-interval <n>
Sets the transmission interval for stacking.
19ꢀ
2.8 Port Settingsꢀ
2.8.1 Port commands - EXEC levelꢀ
show interfaces configꢀ
Displays the basic configuration of the switch ports.
Output Format:
Switch Configuration - Port Settingsꢀ
Port ꢀ Type
Enabled
Mode
Flow Ctrl Bcast Limit
----ꢀ -------- + ------- ------------ --------- -----------
1 ꢀ
2 ꢀ
3 ꢀ
4 ꢀ
5 ꢀ
6 ꢀ
7 ꢀ
8 ꢀ
9 ꢀ
10/100TX | Yes
10/100TX | Yes
10/100TX | Yes
10/100TX | Yes
10/100TX | Yes
10/100TX | Yes
10/100TX | Yes
10/100TX | Yes
10/100TX | Yes
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
0
0
0
0
0
0
0
0
0
0
0
10 ꢀ 10/100TX | Yes
11 ꢀ 10/100TX | Yes
show statistics
Displays a summary of the network traffic handled by the switch.
Output Format:
Status and Counters - Port Countersꢀ
Port Total Bytes Total Frames
Errors Rx
Drops Tx
---- ------------- ------------- ------------- -------------
1
2
3
4
5
6
7
8
83,612,741
446,524
3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
10
0
0
0
15,080
9
10
11
0
0
0
20ꢀ
show statistics <port-number>
Displays the network traffic statistics for the specified port.
Output Format:
Status and Counters - Port Counters - Port 1ꢀ
Link Status
: Upꢀ
Bytes Rx
Unicast Rx
: 83,290,873
: 395,490
Bytes Tx
Unicast Tx
: 1,234,430ꢀ
: 14,995ꢀ
Bcast/Mcast Rx : 40,161
Bcast/Mcast Tx : 180ꢀ
FCS Rx
: 3
: 1
: 0
: 0
Drops Tx : 0ꢀ
Alignment Rx
Runts Rx
Giants Rx
Collisions Tx : 25ꢀ
Late Colln Tx : 0ꢀ
Excessive Colln : 0ꢀ
Total Rx Errors : 4
Deferred Tx
: 17ꢀ
21ꢀ
show interfaces
Displays the status and current configuration of all the switch ports.
Output Format:
Status and Counters - Port Statusꢀ
Intrusion
Alert
Flow
Ctrl
Bcastꢀ
Limitꢀ
Port
Type
Enabled Status
Mode
----ꢀ -------- --------- ------- ------ ---------- --------- ------
1
2
3
4
5
6
7
8
9
10/100TX No
10/100TX No
10/100TX No
10/100TX No
10/100TX No
10/100TX No
10/100TX No
10/100TX No
10/100TX No
10/100TX No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Up
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
Down
Down
Down
Down
Down
Down
Down
Down
Down
10
2.8.2 Ethernet Interface Configuration Commands
To enter the Ethernet Interface Configuration level, use the Interface command described
above. Note that a port-list may be used to configure these options on more than one port
and that any of the following commands can be appended to the Interface command to
simply change the configuration. For example:
HP 4108GL(config)# interface ethernet A1,A3 disableꢀ
broadcast-limit <0..99>
Sets the theoretical maximum of network bandwidth in percentage that can be used
for broadcast traffic. Any broadcast traffic exceeding that limit will dropped. 0 means
the feature is disabled.
disable
Disables the port.
enable
Enables the port.
22ꢀ
[no] flow-control
Enables or disables flow control on the port.
Note: Full-duplex ports only.
speed-duplex <10-full | 10-half | 100-full | 100-half | 1000-full | 10-auto | auto>
Sets the mode of operation for the port.
[no] lacp [active|passive]
enables or disables LACP on the port.
2.9 Trunk Configuration
2.9.1 Trunk commands - EXEC level
show trunks [<port-list>]
Displays trunks that are configured on the system. This does not include dynamic
trunks that have been formed by LACP.
Output Format:
Switch Configuration - Trunksꢀ
Port ꢀ Type
Group
Type
| Port
Type
Group
Typeꢀ
----ꢀ -------- + ----- -------- | ---- -------- + ----- --------
1
2
3
4
5
6
7
8
10/100TX |
| 9
10/100TX |
10/100TX |
10/100TX |
10/100TX |
10/100TX |
10/100TX |
10/100TX |
10/100TX |
10/100TX | Trk1 FEC
10/100TX | Trk1 FEC
10/100TX |
10/100TX | Trk2 Trunk
10/100TX | Trk2 Trunk
10/100TX |
| 10
| 11
| 12
| 13
| 14
| 15
| 16
10/100TX |
23ꢀ
show lacp
Displays LACP status information.
Output Format:
LACPꢀ
P0RT LACP
TRUNK
PORT
LACP
LACPꢀ
NUMB ENABLED GROUP
STATUS PARTNER
STATUSꢀ
----ꢀ -------- ----- -------- --------- ---------
1
2
3
4
5
6
7
8
Active
Passive
Active
Active
Active
Active
Active
Active
Dyn1 Up
Trk1 Down
Blocked No
Disabledꢀ
Dyn1 Up
Yes
No
Successꢀ
Failureꢀ
Failureꢀ
Yes
Successꢀ
Standbyꢀ
Upꢀ
Upꢀ
2.9.2 Trunk commands - Configuration level
[no] trunk <trk1..trk24 > [trunk | fec | lacp] <port list>
This command configures each port in the switch to either be a Trunked, SA Only
Trunked, FEC Trunked port, or a regular singular port.
For Trunks: All ports in a Trunked group, 1 to 4 ports maximum, must have the same
port type.
General Considerations: (1) To avoid broadcast storms, or loops in your network
while configuring trunks, first disable or disconnect all the ports you wish to add or
remove from both sides of the trunk. Once done configuring the trunk, enable or re-
connect the ports. (2) If you have multiple groups of the same or different types and/or
singular connections between two switches, you have created a loop in the network. You
must enable Spanning Tree on both switches to avoid a broadcast storm or other
network problems. See the Switch Management and Configuration Guide for more
information.
Parameters:
ꢀ <trk1..trk24 |none> - Determines the group that a port is configured to be a
member of: trkX indicates a general group of trunked ports; none indicates that the
associated port is a singular independent port (i.e., not part of a trunk).
24ꢀ
ꢀ [type <trunk | fec | lacp>] - Determines the method by which the switch
distributes the traffic load across the multiple links in the trunk group: trunk - uses
source and destination MAC addresses for load distribution (select this to connect to
devices such as the HP Switch 2000 or the Sun Trunk Server); fec - uses an
automatic protocol for load distribution (select this to connect to devices that
support Cisco's Fast EtherChannel trunking).
2.10 Spanning Treeꢀ
2.10.1 Spanning Tree commands - EXEC levelꢀ
show spanning-tree configꢀ
Displays spanning tree configuration information.
Output Format:
Switch Configuration - Spanning Tree Operationꢀ
Spanning Tree Enabled [No] : Noꢀ
STP Priority [32768] : 32768
Hello Time [2] : 2ꢀ
Max Age [20] : 20 ꢀ
Forward Delay [15] : 15ꢀ
Port ꢀ Type
Cost Pri Mode | Port
Type
Cost Pri Mode
----ꢀ -------- + ----- --- ---- | ---- -------- + ----- --- ----
1
2
3
4
5
6
7
10/100TX | 10
10/100TX | 10
10/100TX | 10
10/100TX | 10
10/100TX | 10
10/100TX | 10
10/100TX | 10
128 Norm | 9
128 Norm | 10
128 Norm | 11
128 Norm | 12
128 Norm | 13
128 Norm | 14
128 Norm | 15
10/100TX | 10
10/100TX | 10
10/100TX | 10
10/100TX | 10
10/100TX | 10
10/100TX | 10
10/100TX | 10
128 Norm
128 Norm
128 Norm
128 Norm
128 Norm
128 Norm
128 Norm
25ꢀ
show spanning-tree
Displays bridge-level spanning tree information.
Output Format:
Status and Counters - Spanning Tree Informationꢀ
STP Enabled
Switch Priority
Hello Time
Max Age
: Yesꢀ
: 32,768ꢀ
: 2ꢀ
: 20ꢀ
Forward Delay
: 15ꢀ
Topology Change Count : 1ꢀ
Time Since Last Change : 4 minsꢀ
Root MAC Address
Root Path Cost
Root Port
: 0060b0-885a80ꢀ
: 0ꢀ
: This switch is rootꢀ
Root Priority
: 32768ꢀ
Port
Type
Cost Priority
State
Designated Bridgeꢀ
----ꢀ -------- ----- -------- ---------- -----------------
1
2
3
4
5
6
7
8
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10
10
10
10
10
10
10
10
10
10
10
128 Forwarding 0060b0-885a80ꢀ
128 Disabledꢀ
128 Disabledꢀ
128 Disabledꢀ
128 Disabledꢀ
128 Disabledꢀ
128 Disabledꢀ
128 Disabledꢀ
128 Disabledꢀ
9
10
11
128 Disabledꢀ
128 Disabledꢀ
2.10.2 Spanning Tree commands - Configuration level
[no] spanning-tree
Enables or disables spanning tree on the device.
26ꢀ
spanning-tree [forward-delay <seconds>]
[hello-time <seconds>]
[maximum-age <seconds>]
[priority <0..65535>]
spanning-tree <[ethernet] port-list> [path-cost <1..65535>]
[priority <0..255>]
[mode <norm|fast>]
This command configures the parameters for operation of the switch in a spanning
tree topology. Note - the default spanning tree configuration complies with the
IEEE 802.1D standard recommended values and should not be changed without
thorough knowledge of spanning tree operation. Note: As per IEEE 802.1Q
Standard, this switch implements a single instance of Spanning Tree operating over
all VLANs.
Parameters:
ꢀ path-cost <port-list><1..65535> - Individual port cost used to determine which
ports are forwarding ports. The defaults is 100 for 10 Mbps ports, 10 for
10/100TX and 100FX ports, and 5 for 100/1000TX and 1Gbps ports.
ꢀ priority <port-list><0..255> - Another value used by spanning tree to the
forwarding ports. The port with the lowest number has the highest priority. The
default is 128.
ꢀ mode <port-list> [norm | fast] (default: norm) - norm (for normal) mode causes
the port to operate according to the standard Spanning Tree Protocol - when
connected, the port progresses through the Listening, Learning, and either
Blocking or Forwarding states. fast mode causes the port to immediately
operate in the Forwarding State when a device is connected to it. Use this setting
only on ports that are connected to end nodes (for example: PCs, Workstation,
or printers). Caution: Changing the Mode to fast on ports connected to a hub or
switch may cause loops in your network that STP may not be able to detect, in
all cases.
ꢀ forward-delay <seconds> - Time the switch waits between transition from
listening to learning and from learning to forwarding states. The range is 4 to 30.
The default is 15.
ꢀ hello-time <seconds> - Time (in seconds) between messages transmitted when
the switch is root. The range is 1 to 10. The default is 2.
ꢀ maximum-age <seconds> - Maximum message age (in seconds) of received
STP information before it is discarded. The range is 6 to 40. The default is 20.
ꢀ priority <0..65535> - Switch (or bridge) priority used along with the switch
MAC address to determine which device is the root. The default is 32768.
27ꢀ
2.11 IP
2.11.1 IP commands - EXEC level
show ip
Displays the IP configuration on the switch.
Output Format
There are two different IP configuration screens. The first is displayed when no
vlans are configured on the switch; the second is displayed when vlans are
configured.
Switch Configuration - Internet (IP) Serviceꢀ
Default Gateway: 192.32.36.1ꢀ
TimeP Config [DHCP]: DHCP
TimeP Poll Interval (min) [720]: 720ꢀ
IP Config [DHCP/Bootp] : DHCP/Bootpꢀ
IP Address : 192.32.36.96
Subnet Mask : 255.255.255.192ꢀ
Switch Configuration - Internet (IP) Serviceꢀ
Default Gateway: 192.32.36.1ꢀ
TimeP Config [DHCP]: DHCP
TimeP Poll Interval (min) [720]: 720ꢀ
VLAN
------------ + ----------ꢀ --------------- ---------------
DEFAULT_VLAN | Manual 192.32.36.91 255.255.255.192ꢀ
vlan2 | DHCP/Bootpꢀ
IP Config
IP Address
Subnet Maskꢀ
28ꢀ
show ip authorized-managers
Displays the current configuration's IP managers access records.
Output Format:
Switch Configuration - IP Managersꢀ
Authorized Manager IP IP Mask
Access Levelꢀ
----------------------ꢀ -------------------- ---------------------
192.32.36.78
255.255.255.255
Managerꢀ
show arp
Displays the ARP cache of the switch.
Output Format
ARP Cacheꢀ
IP Address
--------------ꢀ ------------- -----------
192.32.36.78 080009-012345 orange-lanꢀ
MAC Address
VLANꢀ
show ip route
Displays active IP route entries used by the switch.
Output Format
IP Route Entriesꢀ
Network Addr Network Mask Gateway
Port Cost Typeꢀ
--------------ꢀ ------------- ----------- ---- ---- ----
192.32.36.0 255.255.255.0 192.32.36.1 A1 Rꢀ
1
29ꢀ
show timp
Displays active Timep configuration.
Output Format
Timep Configurationꢀ
Time Sync Mode: Timepꢀ
TimeP Mode [Disabled] : Manual
Server Address : 15.29.16.105ꢀ
Poll Interval (min) [720] : 600ꢀ
show sntp
Displays active SNTP configuration.
Output Format
SNTP Configurationꢀ
Time Sync Mode: Timepꢀ
SNTP Mode [Disabled] : Disabledꢀ
Poll Interval (min) [720] : 600ꢀ
30ꢀ
2.11.2 IP commands - Configuration level
[no] ip authorized-managers <ip-addr>
[mask <ip-mask>]
[operator | manager]
Sets the IP addresses you will allow to access the switch’s Web browser interface, to
telnet to the switch console, and to perform TFTP operations. A maximum of 10
addresses is supported.
Parameters:
ꢀ <ip-addr> - The IP address of an authorized manager.
ꢀ mask <ip-mask> - The default mask is 255.255.255.255. A mask that allows you
to define which portions of the listed IP address need to be matched by an
incoming request. For example, with an authorized address of 10.8.11.1 and a
mask of 255.255.255.255, only access from 10.8.11.1 is allowed. With a mask of
255.255.255.0, access from any IP address with 10.8.11.x is allowed.
ꢀ <operator | manager> - The default access level is manager. A designation of
the management capabilities that are accessible to the authorized manager.
manager allows full access to all web browser and the CLI for viewing and
setting the switch configuration, and for performing all other interface
operations, including all TFTP operations. operator allows view-only access
from the web browser and the CLI, but does not allow changing the switch
configuration or any TFTP operations.
[no] timesync <timep | sntp >
Configures the network time protocol to be used by the switch.
[no] timep <dhcp | manual <ip-addr>> [interval <1..9999>]
Configures Timep on the switch.
Parameters:
ꢀ <dhcp | manual> - The method the switch uses to acquire the Timep server
address: dhcp - from a DHCP server; manual - you manually enter the Timep
server address; disable - the switch will not attempt to get its time from a Timep
server.
ꢀ interval <1..9999> (default is 720) How often (in minutes) the switch tries to
get the current time.
ꢀ <ip-addr> - The IP address of the Timep server that the switch gets the current
time from.
31ꢀ
[no] sntp < server <ip-addr> [version]> [poll-interval <30-720>]
Configures SNTP on the switch.
ip default-gateway <ip-addr>
Assigns an IP address to be used as the default gateway when the switch is not in
routing mode.
ip route <<ip-addr>/<1..32> | <ip-addr> <ip-mask>> <ip-addr>
Used to configure a static IP route for the switch.
ip ttl <value>
Sets the maximum time that a packet will live on the network.
[no] arp <ip-addr> [mac-addr]
Used to modify the arp cache.
32ꢀ
2.11.3 IP commands - VLAN Interface level
[no] ip address <dhcp-bootp | <<ip-addr>/<1..32> |
<ip-addr> <ip-mask>] [secondary]>
This command configures the IP address for the switch. Note, by default this
command uses a VLAN identifier of one. Although this command is duplicated at
the VLAN context level, it is defined here for those customers who do not want to
be exposed to VLAN distinctions.
Parameters:
ꢀ dhcp-bootp - The method the switch uses to acquire its IP Service configuration:
dhcp-bootp - the switch attempts to get its IP configuration, or its complete
configuration, from a DHCP/Bootp server, depending on how the server is
configured. If the 'address' is specified at the command line then the interface uses
a 'manual' method in which the IP address and subnet mask are explicitly specified.
If the modal operation 'no' is specified for the interface then the interface becomes
disabled and all IP communication with the switch ceases. This includes SNMP,
management, Web browser access, and telnet access.
ꢀ <ip-addr>/<1..32> - IP address for the switch (or VLAN) IP interface. <1..32> is
the number of bits present in the subnet mask used by all devices in the IP subnet
being configured.
ꢀ <ip-addr> <ip-mask> - This is an alternative syntax for specifying the IP address
and subnet mask described above.
33ꢀ
2.12 SNMP
2.12.1 SNMP commands - EXEC level
show snmp-server
Displays the SNMP communities which may be used to access the switch along with
the network management stations configured to receive SNMP traps.
Output Format:
SNMP Serverꢀ
Community Name MIB View Write Accessꢀ
--------------ꢀ -------- -------------
public
Manager Unrestrictedꢀ
Send Authentication Traps [No] : Noꢀ
Address
----------------------ꢀ ---------------- -------------------
192.32.36.78 public Noneꢀ
Community
Events Sent in Trapꢀ
34ꢀ
2.12.2 SNMP commands – Configuration Level
[no] snmp-server community <community-name>
[manager | operator]
[restricted | unrestricted]
Used to configure a new SNMP community or to edit the configuration for an
existing one
Parameters:
ꢀ <community-name> - Enter (up to 16 characters) the SNMP community name.
ꢀ [manager | operator] - Manager - the community can access all MIB objects;
Operator - the community can access all except the CONFIG MIB.
ꢀ [restricted | unrestricted] - Unrestricted - any MIB variable that has read/write
access can be set; Restricted - MIB variables cannot be set, only read.
[no] snmp-server host <ip-addr> <community-name> [none | all | non-info | critical |
debug]
Configures which network management stations will receive SNMP event log
messages from the switch and the types of events for which the switch will send
these messages.
Parameters:
ꢀ <ip-addr> - Address of the network management station.
ꢀ <community-name> - The name of the SNMP community to which the network
management station belongs.
ꢀ [none | all | non-info | critical | debug] - The level of Switch events that will
generate a Trap to be sent: None - send no log message; All - send all log
messages; Not INFO - send each log message that is not informational-only;
Critical - send critical-level log messages; Debug (reserved for Internal use).
[no] snmp-server enable traps authentication
Enables authentication traps to be sent when a management station attempts an
unauthorized access.
35ꢀ
2.13 VLAN Configurationꢀ
2.13.1 VLAN commands - EXEC levelꢀ
show vlansꢀ
Displays the current VLANs.
Output Format:
Switch Configuration - VLAN Informationꢀ
VLAN Support [No] : Yesꢀ
Maximum VLANs to support [8] : 8ꢀ
Primary VLAN: DEFAULT_VALNꢀ
802.1Q VLAN ID Name ꢀ
Type
Statusꢀ
--------------ꢀ ------------ ------ ------
1
DEFAULT_VLAN ꢀ Static Upꢀ
show vlans <vlan-id>
Displays which ports are assigned to particular VLANs.
Output Format:
Switch Configuration - VLAN - VLAN Port Assignmentꢀ
Port DEFAULT_VLAN
vlan2
| Port DEFAULT_VLAN
vlan2ꢀ
---- + ------------ ------------ | ---- + ------------ꢀ ------------
1
2
3
4
5
6
7
8
| Untagged
| Untagged
| Untagged
| Untagged
| Untagged
| Untagged
| Untagged
| Untagged
No
No
No
No
No
No
No
No
| 9
| Untagged
Noꢀ
Noꢀ
Noꢀ
Noꢀ
Noꢀ
Noꢀ
Noꢀ
Noꢀ
| 10 | Untagged
| 11 | Untagged
| 12 | Untagged
| 13 | Untagged
| 14 | Untagged
| 15 | Untagged
| 16 | Untagged
2.13.2 VLAN commands – Configuration Level
max-vlans <1..256>
Sets the maximum number of VLANs on the system. The default value is 8.
36ꢀ
primary-vlan <vlan-id>
Sets the primary VLAN used for network management.
[no] vlan <vlan-id>
Creates a new VLAN or changes the system context to the VLAN configuration
level. Note that vlan-name can be substituted for the vlan-id when using this command.
static-vlan <vlan-id>
Creates a new static VLAN from one which has been dynamically created by GVRP.
[no] vlan-support
Enables VLAN support on the switch.
2.13.3 VLAN Interface commands
To enter the VLAN Interface Configuration level, use the vlan command described above.
Note that any of the following commands can be appended to the vlan command to simply
change the configuration. For example:
HP 4108GL(config)# add vlan 2 name orange-lanꢀ
name <vlan-name>
Changes the current VLAN identifier’s name.
[no] tagged <port-list>
Assigns ports to current VLAN identifier as tagged.
[no] untagged <port-list>
Assigns ports to current VLAN identifier as untagged.
[no] forbid <port-list>
Forbids the ports from ever becoming a member of the current VLAN.
37ꢀ
auto <port-list>
Causes each port identified in the port-list to learn their VLAN membership using
the Group VLAN Registration Protocol (GVRP). This command is only valid when
GVRP is enabled.
2.14 GVRP
2.14.1 GVRP commands - EXEC level
show gvrp
Displays the current VLANs.
Output Format:
Switch Configuration - GVRP Informationꢀ
GVRP Enabled [No] : Yesꢀ
Port Type
| Unknown VLANꢀ
---- -------- + ------------ꢀ
A1
A2
A3
A4
10/100TX | Learnꢀ
10/100TX | Learnꢀ
10/100TX | Learnꢀ
10/100TX | Learnꢀ
2.14.2 GVRP commands – Configuration level
[no] gvrp
Enables the Group VLAN Registration Protocol (GVRP) on the switch.
2.14.3 Ethernet Interface Configuration commands
unknown-vlans <learn | block |disable>
Defines what the port will do when it encounters GVRP packet requested it to join a
VLAN. If learn is specified then the port will join the advertised VLAN and
propagate a VLAN join requests through all other forwarding ports that are
participating in GVRP. If block is specified then the port will not join the advertised
VLAN and will not propagate any VLAN joins for the advertised VLAN.
38ꢀ
2.15 IGMP
2.15.1 IGMP Commands – EXEC Level
show ip igmp [vlan-id] config
Displays IGMP configuration information.
Output Format:
Switch Configuration - IGMP Serviceꢀ
IGMP Enabled [No] : Noꢀ
Forward with High Priority [No] : Noꢀ
Port
Type
IP Mcast | Port
Type
IP Mcast
---- -------- + -------- | ---- -------- + --------
3
4
5
6
7
8
9
10
10/100TX | Auto
10/100TX | Auto
10/100TX | Auto
10/100TX | Auto
10/100TX | Auto
10/100TX | Auto
10/100TX | Auto
10/100TX | Auto
| 11
| 12
| 13
| 14
| 15
| 16
10/100TX | Auto
10/100TX | Auto
10/100TX | Auto
10/100TX | Auto
10/100TX | Auto
10/100TX | Auto
| Mesh Mesh
|
| Auto
show ip igmp [<vlan-id> | group <group-address>]
When IGMP is enabled, this command shows a summary of the IGMP status for all
the IP Multicast groups used by the selected VLAN. If the feature is not enabled,
then this command displays “IGMP not enabled”.
Output Format:
Status and Counters - IP Multicast (IGMP) Statusꢀ
Active Group Addresses Reports Queries Querier Access Portꢀ
----------------------ꢀ ------- ------- ----------------------
Active Group Address :ꢀ
Port
Type
Access ꢀ
Age timer Leave timerꢀ
----ꢀ -------- ----------- --------- -----------
Active Group Address :ꢀ
Port
Type
Access ꢀ
Age timer Leave timerꢀ
----ꢀ -------- ----------- --------- -----------
39ꢀ
2.15.2 IGMP Configuration commands – Vlan Interface level
[no] ip igmp
Enables the IP Multicast (IGMP) feature for IGMP communication between
Multicast Routers, Multicast Servers, and Multicast Clients connected to the switch
or selected VLAN.
[no] ip igmp high-priority-forward
Determines whether the switch forwards all IP Multicast traffic at high priority.
[no] ip igmp querier
Determines whether the switch is querier or not.
ip igmp <auto|block|forward> <port-list>
Instructs the switch's IGMP feature to control the action taken with an IGMP
frame.
40ꢀ
2.16 Port Monitoringꢀ
2.16.1 Port Monitoring commands - EXEC levelꢀ
show mirror-portꢀ
Displays the configuration of the monitoring port.
Output Format:
Switch Configuration - Network Monitoring Portꢀ
Monitoring Enabled [No] : Yesꢀ
Monitoring Port : 3ꢀ
Monitor : Portsꢀ
Port
Type
Action
| Port
Type
Action
---- -------- + ------- | ---- -------- + -------
3
4
5
6
7
8
9
10/100TX |
10/100TX |
10/100TX |
10/100TX |
10/100TX |
10/100TX |
10/100TX |
| 11
| 12
| 13
| 14
| 15
| 16
10/100TX |
10/100TX |
10/100TX |
10/100TX |
10/100TX |
10/100TX |
| Mesh Mesh
|
2.16.2 Port Monitoring commands - Configuration level
[no] mirror-port [<port-num>]
This command defines the switch port that will be used as the Monitoring Port for
diagnostic purposes. The switch ports that will be monitored are defined through the
monitor command at the Ethernet Interface Configuration Level. All the network
traffic seen by the monitored ports is copied to the Monitoring Port to which a
network analyzer can be attached.
Note: When monitoring multiple ports in a busy network, some frames may not be
copied to the monitoring port.
Parameters:
ꢀ port-num - Port that will be acting as the monitoring port. A configured trunk port
cannot be used.
41ꢀ
2.16.3 Port Monitoring commands - VLAN Interface level
[no] monitor
Used to enable/disable monitoring of the VLAN.
2.16.4 Port Monitoring commands - Ethernet Interface level
[no] monitor
Used to enable/disable monitoring of the port.
2.17 Port Securityꢀ
2.17.1 Port Security commands - EXEC levelꢀ
show port-securityꢀ
Displays the per-port security configuration for the switch.
Output Format:
Switch Configuration - Port Securityꢀ
Port Learn Mode Action
------ ---------- --------------------
3
4
5
6
7
8
9
10
11
12
13
Continuous None
Continuous None
Continuous None
Continuous None
Continuous None
Continuous None
Continuous None
Continuous None
Continuous None
Continuous None
Continuous None
42ꢀ
show port-security [ethernet] <port-list>
Displays the port security configuration for an individual port.
Output Format:
Switch Configuration - Port Securityꢀ
Port : 3ꢀ
Learn Mode [Continuous] : Continuousꢀ
Action [None] : Noneꢀ
show port-security intrusion-log
Displays information on any port security intrusions that have occurred on the
switch.
Output Format:
Status and Counters – Intrusion Logꢀ
Port MAC Address
Date / Timeꢀ
----ꢀ ------------- --------------------------
2.17.2 Port Security commands - Configuration level
port-securityꢀ <port-list>
[learn-mode < continuous | static >]
[address-limit <1..8>]
[action <none | send-alarm | send-disable>]
[no] port-security <port-list>
[mac-address <mac-addr>]
This command configures port security on the switch.
Parameters:
ꢀ learn-mode - If continuous is selected, the switch learns any new address from
packets received on the port. If static is selected, up to the number of addresses
43ꢀ
defined by the "address-limit" parameter are learned or entered for the port.
These addresses are static; they are not aged out.
ꢀ addr-limit <1..8> - This parameter is valid only if static is selected for the
learn-mode. This parameter defines the number of network devices that are
authorized to communicate through the switch port. Up to 8 devices can be
authorized for any port.
ꢀ addr-list <mac-addr> - This parameter is valid only if static is selected for the
learn-mode. If you enter no authorized addresses, the switch will learn and
configure authorized addresses as it detects them on the port, up to the address-
limit number of addresses, and make these the static authorized addresses for the
port. If you enter fewer addresses than the Address Limit, the switch will learn
the additional addresses up to the address-limit. If you enter more addresses than
the address-limit, an error message is displayed when you attempt to Save the
configuration.
ꢀ action - Indicates the action the switch will take if an intruder is detected on the
port.
44ꢀ
3.
Console Menu
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Main Menuꢀ
1. Status and Counters...ꢀ
2. Switch Configuration...ꢀ
3. Console Passwords…ꢀ
4. Event Logꢀ
5. Command Line (CLI)ꢀ
6. Reboot Switchꢀ
7. Download OSꢀ
8. Run Setupꢀ
0. Logoutꢀ
Provides the menu to display configuration, status, and counters.ꢀ
To select menu item, press item number, or highlight item and press <Enter>.ꢀ
3.1 Status and Counters
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters Menuꢀ
1. General System Informationꢀ
2. Switch Management Address Informationꢀ
3. Module Informationꢀ
4. Port Statusꢀ
5. Port Countersꢀ
6. Address Tableꢀ
7. Port Address Tableꢀ
8. Spanning Tree Informationꢀ
0. Return to Main Menu...ꢀ
Displays switch management information including software versions.ꢀ
To select menu item, press item number, or highlight item and press <Enter>.ꢀ
45ꢀ
3.1.1 General System Information
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters - General System Informationꢀ
System Contact
System Location
:ꢀ
:ꢀ
Firmware revision : E.08.XX
Base MAC Addr
Serial Number
: 0060b0-882200ꢀ
:ꢀ
ROM Version
: E.05.X1
Up Time
CPU Util (%)
: 40 mins
: 1
Memory
- Total
Free
: 5,803,088ꢀ
: 2,230,032ꢀ
IP Mgmt - Pkts Rx : 11
Pkts Tx : 0
Packet
Buffers ꢀ Free
- Total
: 438ꢀ
: 272ꢀ
Lowest : 199ꢀ
Missed : 0ꢀ
Actions->
Back
Helpꢀ
Return to previous screen.ꢀ
Use arrow keys to change action selection and <Enter> to execute action.ꢀ
3.1.2 Management Address Information
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters - Management Address Informationꢀ
Time Server Address :ꢀ
MAC Address
IP Address
: 0060b0-882200ꢀ
: 10.0.8.105ꢀ
IPX Network Number :ꢀ
Actions->
Back
Helpꢀ
Return to previous screen.ꢀ
Use arrow keys to change action selection and <Enter> to execute action.ꢀ
46ꢀ
3.1.3 Module Information
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters - Module Informationꢀ
Slot
Module Type
Module Descriptionꢀ
----ꢀ --------------- ---------------------------------------------
A
B
C
D
E
F
G
H
Slot Availableꢀ
Slot Availableꢀ
Slot Availableꢀ
Slot Availableꢀ
Slot Availableꢀ
Slot Availableꢀ
Slot Availableꢀ
Slot Availableꢀ
Actions->
Back
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
3.1.4 Port Status
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters - Port Statusꢀ
Intrusion
Alert
Flow
Ctrl
Bcastꢀ
Limitꢀ
Port
Type ꢀ
Enabled Status
Mode
----ꢀ -------- --------- ------- ------ ---------- --------- ------
1
2
3
4
5
6
7
8
9
10
10/100TX ꢀ No
10/100TX ꢀ No
10/100TX ꢀ No
10/100TX ꢀ No
10/100TX ꢀ No
10/100TX ꢀ No
10/100TX ꢀ No
10/100TX ꢀ No
10/100TX ꢀ No
10/100TX ꢀ No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Up
100HDx
10HDx
10HDx
10HDx
10HDx
10HDx
10HDx
10HDx
10HDx
10HDx
off
off
off
off
off
off
off
off
off
off
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
Down
Down
Down
Down
Down
Down
Down
Down
Down
Actions->
Back
Intrusion log
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
47ꢀ
3.1.5 Port Counters
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters - Port Countersꢀ
Port
Total Bytes
Total Frames
Errors Rx
Drops Txꢀ
----ꢀ ------------- ------------- ------------- -------------
1
2
3
4
5
6
7
8
16,448
217
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0ꢀ
0
0
0
0
0
0
0
0
0
0
9
10
11
0
0
Actions->
Back
Show details
Reset
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
3.1.5.1 Port Counters Details
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters - Port Counters - Port 1ꢀ
Link Status
: Upꢀ
Bytes Rx
Unicast Rx
: 16,088
: 88
Bytes Tx
Unicast Tx
: 360ꢀ
: 4ꢀ
Bcast/Mcast Rx : 124
Bcast/Mcast Tx : 1ꢀ
FCS Rx
: 0
: 0
: 0
: 0
Drops Tx
Collisions Tx
Late Colln Tx
Excessive Colln : 0ꢀ
Deferred Tx : 0ꢀ
: 0ꢀ
: 0ꢀ
: 0ꢀ
Alignment Rx
Runts Rx
Giants Rx
Total Rx Errors : 0
Actions->
Back
Reset
Helpꢀ
Return to previous screen.ꢀ
Use arrow keys to change action selection and <Enter> to execute action.ꢀ
48ꢀ
3.1.6 Address Table
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters - Address Table – VLAN ID 23ꢀ
MAC Address
Located on Portꢀ
-------------ꢀ ---------------
0060b0-e26440 1ꢀ
080009-092851 1ꢀ
080009-76ac55 1ꢀ
080009-97aad2 1ꢀ
Actions->
Back
Search
Next page
Prev page
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
3.1.7 Port Address Table
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters - Port Address Table - Port A1ꢀ
MAC Addressꢀ
-------------ꢀ
0060b0-e26440ꢀ
080009-092851ꢀ
080009-76ac55ꢀ
080009-97aad2ꢀ
Actions->
Back
Search
Next page
Prev page
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
49ꢀ
3.1.8
Spanning Tree Information
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters - Spanning Tree Informationꢀ
STP Enabled
Switch Priority
Hello Time
: Yesꢀ
: 32,768ꢀ
: 2ꢀ
Max Age
: 20ꢀ
Forward Delay
: 15ꢀ
Topology Change Count : 1ꢀ
Time Since Last Change : 4 minsꢀ
Root MAC Address
Root Path Cost
Root Port
: 0060b0-885a80ꢀ
: 0ꢀ
: This switch is rootꢀ
Root Priority
: 32768ꢀ
Actions->
Back
Show ports
Helpꢀ
Return to previous screen.ꢀ
Use arrow keys to change action selection and <Enter> to execute action.ꢀ
3.1.8.1 Spanning Tree Port Information
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Status and Counters - Spanning Tree - Port Informationꢀ
Port
Type
Cost
Priority
State
Designated Bridge
---- ------------ ----- -------- ---------- -----------------
1
2
3
4
5
6
7
8
9
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10/100TX
10
10
10
10
10
10
10
10
10
128 Forwarding 0060b0-885a80
128 Disabled
128 Disabled
128 Disabled
128 Disabled
128 Disabled
128 Disabled
128 Disabled
128 Disabledꢀ
Actions->
Back
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to scroll to other entries, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
50ꢀ
3.2 Configuration Menu
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration Menuꢀ
1. System Informationꢀ
2. Port/Trunk Settingsꢀ
3. Network Monitoring Portꢀ
4. Spanning Tree Operationꢀ
5. IP Configurationꢀ
6. SNMP Community Namesꢀ
7. Authorized Managersꢀ
8. VLAN Menu...ꢀ
0. Return to Main Menu...ꢀ
Configures system-level information including system identification.ꢀ
To select menu item, press item number, or highlight item and press <Enter>.ꢀ
51ꢀ
3.2.1 System Information
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration - System Informationꢀ
System Name : DEFAULT_CONFIGꢀ
System Contact :ꢀ
System Location :ꢀ
Inactivity Timeout (min) [0] : 0 ꢀ
Inbound Telnet Enabled [Yes] : Yes ꢀ
Address Age Interval (min) [5] : 5ꢀ
Web Agent Enabled [Yes] : Yesꢀ
Time Zone [0] : 0ꢀ
Daylight Time Rule [None] : Noneꢀ
Actions->
Cancel
Edit
Save ꢀ
Helpꢀ
Cancel changes and return to previous screen.ꢀ
Use arrow keys to change action selection and <Enter> to execute action.ꢀ
3.2.2 Port/Trunk Settings
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration – Port/Trunk Settingsꢀ
Port
Type
Enabled
Mode
Flow Ctrl
Group
Typeꢀ
---- -------- + -------ꢀ ---------- --------- ----------- ----------
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
10/100TX | Yes ꢀ
10/100TX | Yes ꢀ
10/100TX | Yes ꢀ
10/100TX | Yes ꢀ
10/100TX | Yes ꢀ
10/100TX | Yes ꢀ
10/100TX | Yes ꢀ
10/100TX | Yes ꢀ
10/100TX | Yes ꢀ
10/100TX | Yes ꢀ
10/100TX | Yes ꢀ
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Disable
Dyn
Dyn
Trk1
Trk1
LACP
LACP
Trunk
Trunk
Trk2
Trk2
Dyn
Trk2
MESH
MESH
FEC
FEC
LACP
FEC
Actions->
Cancel
Edit
Save
Helpꢀ
Cancel changes and return to previous screen.ꢀ
Use arrow keys to change action selection and <Enter> to execute action.ꢀ
52ꢀ
3.2.3 Network Monitoring Port
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration – Network Monitoring Portꢀ
Monitoring Enabled [No] : Yesꢀ
Monitoring Port : A1ꢀ
Monitor : Portsꢀ
Port
Type
Action ꢀ
Port ꢀ Type
Actionꢀ
---- -------- + -------ꢀ
---- -------- + -------ꢀ
A7 ꢀ 10/100TX |ꢀ
A8 ꢀ 10/100TX |ꢀ
B1 ꢀ 10/100TX |ꢀ
B2 ꢀ 10/100TX |ꢀ
B3 ꢀ 10/100TX |ꢀ
B4 ꢀ 10/100TX |ꢀ
A1
A2
A3
A4
A5
A6
10/100TX | ꢀ
10/100TX | ꢀ
10/100TX | ꢀ
10/100TX | ꢀ
10/100TX | ꢀ
10/100TX | ꢀ
Actions->
Cancel
Edit
Save ꢀ
Helpꢀ
Cancel changes and return to previous screen.ꢀ
Use arrow keys to change action selection and <Enter> to execute action.ꢀ
3.2.4 Spanning Tree Operation
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration – Spanning Tree Operationꢀ
Spanning Tree Enabled [No] : Noꢀ
STP Priority [32768] : 32768 ꢀ
Hello Time [2] : 2ꢀ
Max Age [20] : 20 ꢀ
Forward Delay [15] : 15ꢀ
Port
Type
Cost ꢀ Pri Modeꢀ
---- -------- + -----ꢀ --- ----
A1
A2
A3
A4
A5
A6
A7
A8
10/100TX | 10 ꢀ
10/100TX | 10 ꢀ
10/100TX | 10 ꢀ
10/100TX | 10 ꢀ
10/100TX | 10 ꢀ
10/100TX | 10 ꢀ
10/100TX | 10 ꢀ
10/100TX | 10 ꢀ
128 Normꢀ
128 Normꢀ
128 Normꢀ
128 Normꢀ
128 Normꢀ
128 Normꢀ
128 Normꢀ
128 Normꢀ
Actions->
Cancel
Edit
Save
Helpꢀ
Cancel changes and return to previous screen.ꢀ
Use arrow keys to change action selection and <Enter> to execute action.ꢀ
53ꢀ
3.2.5 IP Configuration
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration - Internet (IP) Serviceꢀ
Default Gateway : 10.0.8.1ꢀ
Time Protocol Config [DHCP] : DHCPꢀ
TimeP Poll Interval (min) [720] : 720ꢀ
IP Config [DHCP/Bootp] : Manualꢀ
IP Address : 10.0.8.105ꢀ
Subnet Mask : 255.255.248.0ꢀ
Actions->
Cancel
Edit
Save
Helpꢀ
Cancel changes and return to previous screen.ꢀ
Use arrow keys to change action selection and <Enter> to execute action.ꢀ
With multiple Vlans configured:
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration - Internet (IP) Serviceꢀ
Default Gateway : 10.0.8.1ꢀ
Time Protocol Config [DHCP] : DHCPꢀ
TimeP Poll Interval (min) [720] : 720ꢀ
VLAN
IP Config
Ip Address
Subnet Maskꢀ
----------- + ---------ꢀ ------------ ---------------
Orange Lan | Manual
10.0.8.105
255.255.248.0ꢀ
Yellow Lan | Disabledꢀ
Actions->
Cancel
Edit
Save
Helpꢀ
Cancel changes and return to previous screen.ꢀ
Use arrow keys to change action selection and <Enter> to execute action.ꢀ
54ꢀ
3.2.6 SNMP Communities
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration - SNMP Communitiesꢀ
Community Name
MIB View Write Accessꢀ
----------------ꢀ -------- ------------
public
Manager
Unrestrictedꢀ
Actions->
Back
Add
Edit
Delete
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to change record selection, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
3.2.7 Authorized Managers
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration – Authorized Managersꢀ
Authorized Manager
--------------------ꢀ ---------------
15.29.16.80 255.255.255.255
IP Mask
Access Levelꢀ
------------
Managerꢀ
Actions->
Back
Add
Edit
Delete
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to change record selection, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
55ꢀ
3.2.8 VLAN Menu
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration - VLAN Menuꢀ
1. VLAN Supportꢀ
2. VLAN Namesꢀ
3. VLAN Port Assignmentꢀ
4. Return to Previous Menu...ꢀ
0. Return to Main Menu...ꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to change record selection, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
3.2.8.1 VLAN Support
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration - VLAN Supportꢀ
Activate VLANs [No] : Yesꢀ
Maximum Vlnas to support [8] : 8ꢀ
Primary VLAN : DEFAULT_VLANꢀ
GVRP Enabled [No] : Noꢀ
Actions->
Back
Add
Edit
Delete
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to change record selection, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
56ꢀ
3.2.8.2 VLAN Names
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration - VLAN Namesꢀ
Name
802.1Q VLAN IDꢀ
------------ꢀ --------------
DEFAULT_VLAN 1ꢀ
Actions->
Back
Add
Edit
Delete
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow keys to change record selection, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
3.2.8.3 VLAN Port Assignment
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Configuration - VLAN Port Assignmentꢀ
Port
DEFAULT_VLAN
| Port
| ---- + ------------ꢀ
DEFAULT_VLANꢀ
---- + ------------
A1
A2
A3
A4
A5
A6
A7
A8
A9
| Tagged ꢀ
| Tagged ꢀ
| Tagged ꢀ
| Tagged ꢀ
| Tagged ꢀ
| Tagged ꢀ
| Tagged ꢀ
| Tagged ꢀ
| Tagged ꢀ
| E1
| E2
| E3
| E4
| E5
| E6
| E7
| E8
| E9
| Untaggedꢀ
| Untaggedꢀ
| Untaggedꢀ
| Untaggedꢀ
| Untaggedꢀ
| Untaggedꢀ
| Untaggedꢀ
| Untaggedꢀ
| Untaggedꢀ
A10 | Tagged ꢀ
A11 | Tagged ꢀ
A12 | Tagged ꢀ
| E10 | Untaggedꢀ
| E11 | Untaggedꢀ
| E12 | Untaggedꢀ
Actions->
Cancel
Edit
Save
Helpꢀ
Use arrow keys to change field selection, <Space> to toggle field choices,ꢀ
and <Enter> to go to Actions.ꢀ
57ꢀ
3.3 Password Menu
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Set Password Menuꢀ
1. Set Operator Passwordꢀ
2. Set Manager Passwordꢀ
3. Delete Password Protectionꢀ
4. Return to Previous Menu...ꢀ
0. Return to Main Menu...ꢀ
Prompts you to enter an Operator-level password.ꢀ
To select menu item, press item number, or highlight item and press <Enter>.ꢀ
3.4 Event Log
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
M 01/01/90 00:00:07 sys: 'System reboot due to Power Failure'ꢀ
I 01/01/90 00:00:07 system: --------------------------------------------------ꢀ
I 01/01/90 00:00:07 system: System went down without saving crash informationꢀ
I 01/01/90 00:00:29 timep: timep client enabledꢀ
I 01/01/90 00:00:29 garp: GARP Protocol enabledꢀ
I 01/01/90 00:00:31 tftp: Enable succeededꢀ
I 01/01/90 00:00:31 system: System Booted.ꢀ
I 01/01/90 00:00:37 ports: port 1 is now on-lineꢀ
I 01/01/90 00:00:37 ip: network enabled on 10.0.8.105ꢀ
I 01/01/90 00:39:55 mgr: SME CONSOLE Session - MANAGER Mode establishedꢀ
---- Log events stored in memory 1-13. Log events on screen 1-13.ꢀ
Actions->
Back
Next page
Prev page
End
Helpꢀ
Return to previous screen.ꢀ
Use up/down arrow scroll log one line, left/right arrow keys toꢀ
change action selection, and <Enter> to execute action.ꢀ
58ꢀ
3.5 Download Screen
HP ProCurve Switch xxxxx ꢀ
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Download OSꢀ
Current Firmware revision : E.08.XXꢀ
Method [TFTP] : TFTPꢀ
TFTP Server :ꢀ
Remote File Name :ꢀ
Actions->
Cancel
Edit
eXecute
Helpꢀ
Select the file transfer method (TFTP and XMODEM are currently supported).ꢀ
Use arrow keys to change field selection, <Space> to toggle field choices,ꢀ
and <Enter> to go to Actions.ꢀ
3.6 Run Setup
HP ProCurve Switch xxxxx
01-Apr-2000ꢀ
==========================- CONSOLE - MANAGER MODE -============================ꢀ
Switch Setupꢀ
System Name : HP ProCurve Switch xxxxxꢀ
System Contact :ꢀ
Manager Password :
Confirm Password:ꢀ
Logon Default : Menu
Community Name : public
Time Zone [0] : 0ꢀ
Spanning Tree Enabled [No] : Noꢀ
Default Gateway : 10.0.8.1ꢀ
TimeP Config [DHCP] : DHCPꢀ
IP Config [DHCP/Bootp] : Manualꢀ
IP Address : 10.0.8.80
Subnet Mask : 255.255.248.0ꢀ
Actions->
Cancel
Edit
eXecute
Helpꢀ
Select the file transfer method (TFTP and XMODEM are currently supported).ꢀ
Use arrow keys to change field selection, <Space> to toggle field choices,ꢀ
and <Enter> to go to Actions.ꢀ
59ꢀ
Index
ip route ..............................................................32ꢀ
ip ttl ...................................................................32ꢀ
Aꢀ
aaa authentication console ................................16ꢀ
aaa authentication telnet....................................16ꢀ
arp......................................................................32ꢀ
auto....................................................................38ꢀ
auto-tftp.............................................................14ꢀ
Kꢀ
kill .......................................................................7ꢀ
Lꢀ
lacp....................................................................23ꢀ
link-test................................................................9ꢀ
logout ..................................................................5ꢀ
Bꢀ
boot......................................................................6ꢀ
broadcast-limit ..................................................22ꢀ
Mꢀ
Cꢀ
mac-age-time.....................................................14ꢀ
max-vlans..........................................................36ꢀ
menu....................................................................5ꢀ
mirror-port.........................................................41ꢀ
monitor..............................................................42ꢀ
cdp.....................................................................17ꢀ
cdp enable .........................................................17ꢀ
cdp holdtime......................................................17ꢀ
cdp timer ...........................................................17ꢀ
clear arp...............................................................7ꢀ
clear intrusion-log ...............................................8ꢀ
clear statistics......................................................8ꢀ
configure .............................................................5ꢀ
console ..............................................................14ꢀ
copy.................................................................6, 9ꢀ
Nꢀ
name..................................................................37ꢀ
Pꢀ
page .....................................................................6ꢀ
password............................................................16ꢀ
ping....................................................................10ꢀ
port-security ......................................................43ꢀ
primary-vlans ....................................................37ꢀ
print .....................................................................7ꢀ
Dꢀ
daylight-time-rule .............................................15ꢀ
disable ...............................................................22ꢀ
Eꢀ
Rꢀ
enable ............................................................5, 22ꢀ
end.......................................................................5ꢀ
erase flash............................................................6ꢀ
erase startup-config.............................................6ꢀ
exit.......................................................................5ꢀ
reload...................................................................7ꢀ
repeat...................................................................6ꢀ
Sꢀ
setmib..................................................................9ꢀ
setup ....................................................................5ꢀ
show arp ............................................................29ꢀ
show boot-history................................................7ꢀ
show cdp ...........................................................17ꢀ
show console.....................................................11ꢀ
show flash ...........................................................9ꢀ
show gvrp..........................................................38ꢀ
show history ........................................................7ꢀ
show interfaces..................................................22ꢀ
show interfaces config ......................................20ꢀ
show ip ..............................................................28ꢀ
show ip authorized-managers ...........................29ꢀ
show ip igmp.....................................................39ꢀ
show ip igmp config..........................................39ꢀ
show ip route.....................................................29ꢀ
show lacp...........................................................24ꢀ
show logging.......................................................7ꢀ
show mac-address ...................................... 11, 12ꢀ
Fꢀ
flow-control.......................................................23ꢀ
Gꢀ
getmib..................................................................8ꢀ
gvrp ...................................................................38ꢀ
Hꢀ
hostname ...........................................................15ꢀ
Iꢀ
interface...............................................................5ꢀ
ip 33ꢀ
ip authorized-managers.....................................31ꢀ
ip default-gateway.............................................32ꢀ
ip igmp ..............................................................40ꢀ
ip igmp high-priority-forward...........................40ꢀ
ip igmp querier..................................................40ꢀ
60ꢀ
show management.............................................12ꢀ
show mirror-port ...............................................41ꢀ
show modules....................................................13ꢀ
show port-security.......................................42, 43ꢀ
show port-security intrusion log .......................43ꢀ
show running-config ...........................................7ꢀ
show snmp-server community..........................34ꢀ
show sntp...........................................................30ꢀ
show spanning-tree ...........................................26ꢀ
show spanning-tree config ................................25ꢀ
show stack.........................................................18ꢀ
show startup-config.............................................7ꢀ
show statistics ...................................................20ꢀ
show system-information..................................13ꢀ
show tacacs .......................................................17ꢀ
show tech.............................................................9ꢀ
show timep ........................................................30ꢀ
show trunks .......................................................23ꢀ
show version .......................................................9ꢀ
show vlans.........................................................36ꢀ
snmp-server.......................................................15ꢀ
snmp-server community....................................35ꢀ
snmp-server enable traps...................................35ꢀ
snmp-server host ...............................................35ꢀ
sntp....................................................................32ꢀ
spanning-tree.....................................................26ꢀ
speed-duplex .....................................................23ꢀ
stack ..................................................................18ꢀ
stack auto-grab..................................................19ꢀ
stack auto-join...................................................19ꢀ
stack commander...............................................18ꢀ
stack join ...........................................................18ꢀ
stack member ....................................................18ꢀ
stack transmission-interval................................19ꢀ
static-vlan..........................................................37ꢀ
Wꢀ
walkmib...............................................................8ꢀ
web-management ..............................................16ꢀ
write memory ......................................................6ꢀ
write terminal ......................................................6ꢀ
Tꢀ
tacacs-server host..............................................17ꢀ
tacacs-server timeout ........................................17ꢀ
tagged................................................................37ꢀ
telnet....................................................................8ꢀ
telnet-server.......................................................16ꢀ
time....................................................................15ꢀ
timep..................................................................31ꢀ
timesync ............................................................31ꢀ
time-zone...........................................................15ꢀ
trunk ..................................................................24ꢀ
Uꢀ
unknown-vlans..................................................38ꢀ
untagged............................................................37ꢀ
Vꢀ
vlan................................................................6, 37ꢀ
vlan-support ......................................................37ꢀ
61ꢀ
|