HITACHI 51F710S User Manual

PROJECTION COLOR TV

Operating Guide for 51F710, 57F710,

65F710, 51F710S, 57F710S, 65F710S

IMPORTANT SAFETY INSTRUCTIONS ................................................................................ 2-3

FIRST TIME USE .................................................................................................................. 4-19

THE REMOTE CONTROL .................................................................................................. 20-32

ON-SCREEN DISPLAY........................................................................................................ 33-64

CARE OF YOUR HITACHI TV AND REMOTE CONTROL ........................................................65

RECEPTION PROBLEMS..........................................................................................................66

USEFUL INFORMATION .................................................................................................... 67-70

57” / 65” DISASSEMBLY/ASSEMBLY INSTRUCTIONS ....................................................71-76

INDEX ........................................................................................................................................77

END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE..............................78-79

As an ENERGY STAR^®Partner, Hitachi, Ltd. has determined that this

product meets the ENERGY STAR^®guidelines for energy efficiency.

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

15. Televisions are designed to comply with the recommended

safety standards for tilt and stability.

Follow all warnings and instructions marked on this television.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

Do not apply excessive pulling force to the front, or top, of the

cabinet which could cause the product to overturn resulting

in product damage and/or personal injury.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or ground-

ing-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades

and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for replacement

of the obsolete outlet.

16. Follow instructions for wall, shelf or ceiling mounting as rec-

ommended by the manufacturer.

17. An outdoor antenna should not be located in the vicinity of

overhead power lines or other electrical circuits.

18. If an outside antenna is connected to the receiver be sure the

antenna system is grounded so as to provide some protec-

tion against voltage surges and built up static charges.

Section 810 of the National Electric Code, ANSI/NFPA No.

70-1984, provides information with respect to proper ground-

ing for the mast and supporting structure, grounding of the

lead-in wire to an antenna discharge unit, size of grounding

connectors, location of antenna-discharge unit, connection to

grounding electrodes and requirements for the grounding

electrode.

ANTENNA

LEAD IN

WIRE

10. Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

GROUND

CLAMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

11. Only use the attachments/accessories specified by the man-

ufacturer.

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUNDING CONDUCTORS

12.

Use only with the cart, stand, tripod, brack-

et, or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the

cart/apparatus combination to avoid injury

from tip-over.

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250 PART H)

NEC NATIONAL ELECTRICAL CODE

Note to the CATV system installer: This reminder is provided

to call the CATV system installer’s attention to Article 820-40

of the NEC that provides guidelines for proper grounding

and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close

to the point of cable entry as practical.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

• This digital television is capable of receiving analog basic, digital basic and digital premium cable television programming by direct con-

nection to a cable system providing such programming. A CableCARD provided by your cable operator is required to view encrypted

digital programming. Certain advanced and interactive digital cable services such as video-on-demand, a cable operator’s enhanced

program guide and data-enhanced television services may require the use of a set-top box. For more information call your local cable

company.

• Do not place any objects on the top of the television which may fall or cause a child to climb to retrieve the objects.

• Projection TV’s are heavy and can mark or damage floor surfaces (especially wood flooring) if moved improperly. Do not slide or

force TV into position. Always roll TV allowing casters at bottom of unit to help steer and position the TV.

• PREVENTION OF SCREEN BURN

This Wide Screen TV is designed to display wide screen pictures. Images should be viewed mostly in wide screen format or

zoomed to fit the screen with moving pictures. Use of side panels, top and bottom panels of standard picture formats should only

be 15% of your total viewing time to prevent uneven aging of the phosphors. Phosphors in the lighted area of the picture will age

more rapidly than the gray areas. Continuous on-screen displays such as video games, stock market quotations, computer

generated graphics, and other fixed (non-moving) patterns can cause permanent damage to television receivers. Such “SCREEN

BURNS” constitute misuse and are NOT COVERED by your HITACHI Factory Warranty.

• PUBLIC VIEWING OF COPYRIGHTED MATERIAL

Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require

prior authorization from the broadcaster or owner of the video program material.

• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.

Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other

limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

This product contains lead. Dispose of this product in accordance with applicable environmental laws. For prod-

uct recycling and disposal information, contact your local government agency or the Electronic Industries Alliance

at www.eiae.org (in the US) or the Electronic Product Stewardship Canada at www.epsc.ca (in Canada). For more

information, call 1-800-HITACHI.

ACCESSORIES

Check to make sure you have the following accessories before disposing of the packing material.

“Z” ALLEN KEY

REMOTE CONTROL

BATTERIES

(“AA”)

For 57” and 65” Models Only

OPTIONAL TV TOP SHELF (NOT INCLUDED, ORDER SEPARATELY)

Model No. Part No.

SLF10

QJ01611

CAUTION: This SLF10 TV Top Shelf for use only with Hitachi 51F710, 51F710S and 57F710, 57F710S. Use with other

apparatus is capable of resulting in instability causing possible injury.

1. Remote Control Unit CLU-4341UG2 (Part No. HL02071) or CLU4351UG2 (Part No. HL02072).

2. Two “AA” size, 1.5V batteries (For Remote Control Unit).

3. “Z” Allen Key (Part No. 61010122).

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

1. Open the battery cover of the remote control by pushing down

and sliding the back cover off.

BOTTOM VIEW

(Remote Control)

2. Insert two new “AA” size batteries for the remote control.

When replacing old batteries, push them towards the springs

and lift them out.

3. Match the batteries to the (+) and (-) marks in the battery compartment.

4. Replace the cover.

Lift up on tab to

remove back cover.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace with the same or equivalent type.

HOW TO SET UP YOUR NEW HITACHI PROJECTION TV

ANTENNA

Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor TV antenna is recommended for

best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image

ghosts, an indoor antenna may be sufficient.

LOCATION

Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location

selected allows a free flow of air to and from the perforated back cover of the set.

To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can

become excessively hot, for example, in direct sunlight or near a heating appliance, etc.

NOTE:

Your new HDTV has a built-in high definition television signal processor. This television includes a fan to cool the

processor. The sound of moving air from the fan is normal and maybe noticeable in very quiet environments.

VIEWING

The major benefit of the HITACHI Projection Television is its large viewing screen. To see this large screen at its best, test various

locations in the room to find the optimum spot for viewing.

The best picture is seen by sitting directly in front of the TV and about 10 to 18 feet from the screen. Picture brightness decreases as

the viewer moves to the left and right of the receiver.

During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the

reflection or the TV can be located in a different section of the room.

If the TV’s audio output will be connected to a Hi-Fi system’s external speakers, the best audio performance will be obtained by placing

the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For

best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround speakers to the side or

behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker

placement for best performance.

20'

4" Minimum

BEST

HORIZONTAL

BEST

VERTICAL VIEWING

ANGLE

10'

15'

20'

VIEWING ANGLE

3’

5’

4" Minimum

0’

10’

15’

20’

CAUTION: Magnetic fields, such as those of external speakers, may cause the picture to distort if they are placed too close

to the television. Move the magnetic field source away from the television until there is no picture distortion.

HOOK-UP CABLES AND CONNECTORS

Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For

best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell

audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output

and input connector types required by the various components and the length of each cable.

300-Ohm Twin Lead Connector

This outdoor antenna cable must be connected to an antenna

adapter (300-Ohm to 75-Ohm).

Optical Cable

This cable is used to connect to an audio amplifier with an

Optical Audio In jack. Use this cable for the best sound quality.

Phono Connector

Used on all standard video and audio cables which connect to

inputs and outputs located on the television’s rear jack panel

and front control panel.

D-SUB MINI 9-Pin Cable

This cable is used to connect to the RS232C input located on the

rear panel so you can control some of your TV functions from an

external home control system.

“F”Type 75-Ohm Coaxial Antenna Connector

For connecting RF signals (antenna or cable TV) to the antenna

jack on the television.

HDMI Cable

S-Video (Super Video) Connector

This cable is used to connect your external devices such as Set-

Top-Boxes or DVD players equipped with an HDMI output con-

nection to the TV’s HDMI input.

This connector is used on camcorders, VCRs and laser- disc

players with an S-Video feature in place of the

standard video cable to produce a high quality picture.

ANTENNA CONNECTIONS TO REAR JACK PANEL

VHF (75-Ohm) antenna/CATV (Cable TV)

To outdoor antenna

or CATV cable

When using a 75-Ohm coaxial cable system, connect CATV coaxial cable to the ANT

A (75-Ohm) terminal. If you have an antenna, connect the coaxial cable to the ANT

B terminal.

To antenna

To outdoor VHF

or UHF antenna

VHF (300-Ohm) antenna/UHF antenna

When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or

UHF antenna leads to screws of the VHF or UHF adapter. Plug the adapter into

the antenna terminal on the TV.

From outdoor

antenna or

CATV System

ANT A

From UHF antenna

When both VHF and UHF antennas are connected

Attach an optional antenna cable mixer to the TV antenna terminal, and connect

the cables to the antenna mixer. Consult your dealer or service store for the

antenna mixer.

Antenna Mixer

FRONT PANEL CONTROLS

ቩ

ቪ

ቦ

INPUT 5

MAGIC

FOCUS

VOL-

VOL+

CH-

CH+

INPUT

EXIT

AUDIO

SELECT

VIDEO

L/MONO

S-VIDEO

CURSOR

ባ

ቢ

ቧ

ቦ

ቤ

ብ

ቨ

ቢ MENU/SELECT button

This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This

button also serves as the SELECT button when in MENU mode.

ባ INPUT/EXIT button

Press this button to display the input menu, Ant A/B, INPUT:1,2,3,4 and 5. This button also serves as the EXIT button when in

MENU mode.

ቤ CHANNEL selector

Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as

the cursor down (̄) and up (̆) buttons when in MENU mode.

ብ VOLUME level

Press these buttons for your desired sound level. The volume level will be displayed on the TV screen. These buttons also serve

as the cursor left (̇) and right (̈) buttons when in MENU mode. When the TV power is turned OFF at a volume level 31 or greater,

the volume level will default to 30 when the TV is turned ON. However, if it is set to a level 30 or less, the volume level will be at the

level it was set when the TV is turned ON.

ቦ POWER button/ POWER LED

Press this button to turn the TV on or off. This LED light is on during normal operation. At initial TV Turn “ON”, the Power button

LED will blink several times before a channel can be tuned and viewed. This is a normal default operation of this television. The

blinking time of the Power button LED varies depending on the period of time between when you turn “ON” and when you turn “OFF”

the TV. This default operation is an energy saving feature. You can choose not to use this feature by selecting “On” for the “Quick

Start Up” option in the On-Screen-Display Menu. Select “Setup” in the On-Screen-Display Menu, then select “Quick Start Up”. Select

the “On” feature to quickly tune and view channels at initial TV Turn “ON” (see page 64).

ቧ MAGIC FOCUS

Use this button to automatically adjust your picture quality to optimum performance (see page 55).

ቨ FRONT INPUT JACKS (INPUT 5)

Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view your favorite show or new recording.

Press the INPUT button and select Input 5. If you have mono sound, insert the audio cable into the left audio jack.

ቩ IR RECEIVER Sensor (1)

The screen area acts as one of the IR receivers (remote sensor) of the TV. When using the remote control, point it towards the

screen for best response.

ቪ IR RECEIVER Sensor (2)

This is an additional remote sensor for a better remote control range of response.

FRONT PANEL JACKS AND CONNECTORS

The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following

examples:

INPUT 5

AUDIO

VIDEO

L/MONO

VIDEO

L/MONO

S-VIDEO

NOTE:

1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture

may be abnormal.

2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable.

3. If you have a mono VCR, insert the audio cable into the left audio jack of your TV.

REAR PANEL JACKS

ቢ

ቦ

CableCARD

(Top of card faces right)

ቭ

ANT A

HDMI 1

INPUT 2

VIDEO

INPUT 1

VIDEO

ANT B

INPUT 4

MONITOR OUT

S-VIDEO

INPUT 3

ቤ

ብ

OPTICAL OUT

ቨ

ቩ

Digital Audio

Upgrade Card

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

VIDEO

AUDIO

(MONO)

RS232C

TV AS CENTER

AUDIO

TO HI-FI

ባ

ቫቧ

ቪ

ቢ Antenna Input

ANT A- A 75-Ohm RF antenna or CATV (Cable TV) input. ANT A can be displayed as a main picture or sub-picture.

ANT B- A 75-Ohm RF antenna input. ANT B can only be displayed as a main picture. ANT B cannot be displayed as a

sub-picture.

NOTE:

You may ask your local cable company whether DTV services are available.

ባ Audio/Video Inputs 1, 2, 3 and 4

By using the INPUTS button, CURSOR buttons and SELECT button of the remote control you can select each video source. Use

the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have

mono sound, insert the audio cable into the left audio jack.)

NOTE:

You may use VIDEO or S-VIDEO inputs to connect to INPUT 3 and 4, but only one of these inputs may be used at a

time.

ቤ MONITOR OUT

These jacks provide fixed or variable audio and video signals which are used for recording. Use the S-VIDEO Output for high

quality video output (see page 63).

ብ S-VIDEO Inputs 3 and 4

Inputs 3 and 4 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.

ቦ Component:Y-P_BP_RInputs

Inputs 1 and 2 provide Y-P_BP_Rjacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may

use composite video signal for both inputs.

NOTES: 1. Do not connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time. S-VIDEO has priority

over VIDEO input.

Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s P input and

the components R-Y output to the TV’s P input.

3. Your component outputs may be labeled Y-C C . In this case, connect the component C output to the TV’s P input and the

B R

component C output to the TV’s P input.

4. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-P P inputs (see page 37).

B R

5. To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-P P jacks.

B R

6. Input 1 and Input 2 (Y/VIDEO) can be used for composite video and component video input.

REAR PANEL JACKS

ቧ HDMI1 (High Definition Multimedia Interface) (INPUT 1)

About HDMI

HDMI is the next-generation all digital interface for consumer electronics. HDMI enables the secure distribution of uncompressed

high-definition video and multi-channel audio in a single cable. Because digital television (DTV) signals remain in digital format,

HDMI assures that pristine high-definition images retain the highest video quality from the source all the way to your television

screen.

Use the HDMI input for your external devices such as Set-Top-Boxes or DVD players equipped with an HDMI output connection.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

NOTES: 1. The HDMI input is not intended for use with personal computers.

2. Only DTV formats such as 1080i, 720p, 480i and 480p are available for HDMI input.

ቨ Optical Out (Digital Audio)

This jack provides Digital Audio Output for your audio device that is Dolby^®Digital and PCM compatible, such as an audio amplifier.

NOTE: *Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby

Laboratories.

ቩ Upgrade Card

This card slot is for future software upgrades. Hitachi will notify you if a software upgrade is required for your TV. In order to receive

written notification, please complete and return your warranty card.

ቪ RS232C Input

For use with third party home Audio/Video control systems which are commercially available. Please see your dealer regarding

these “non Hitachi” home control systems (see page 64 to activate this input).

ቫ TV AS CENTER (INPUTS 1-4)

These jacks are for stereo amplifiers with center signal output capability. This feature allows the TV speakers to be used as a center

speaker. The TV must be set as a center channel by selecting “TV as Center” on the Internal Speakers Settings of the Audio Menu

(see page 41).

REAR PANEL JACKS

ቭ CableCARD Slot

This slot is for the CableCARD that will be provided by your local cable operator to gain access to chosen cable channels. The

CableCARD will allow you to tune digital and high definition cable channels. Please call your local cable operator if this service is

available before requesting a CableCARD (also known as Point of Deployment (POD) module).

Connect a coaxial cable to ANT A terminal of the Rear Panel Jacks.

Insert the CableCARD into the slot (Top of card should be facing right as shown).

Digital Cable

CableCARD

(Top of card faces right)

ANT A

THIS END

HDMI 1

INSER

INPUT 2

VIDEO

INPUT 1

VIDEO

ANT B

INPUT 4

MONITOR OUT

S-VIDEO

INPUT 3

CableCARD

OPTICAL OUT

Digital Audio

Upgrade Card

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

VIDEO

AUDIO

(MONO)

RS232C

TV AS CENTER

AUDIO

TO HI-FI

If the CableCARD is properly installed or not installed, the TV will display the following respective screens.

CableCARD is installed

CableCARD

is not installed

After the CableCARD is installed, wait until the second screen below appears. The third screen below will appear if a channel is not

authorized for viewing. Press the EXIT button to exit the second screen.

In order to start cable service

for this device, please contact

your cable provider

CableCARD(tm): 123-456-789-1

Host: 123-456-789-1

Data: 123-456-789-1

Acquiring Data.

Please wait.

UnitAddress: 123-456-789-1

Not an Authorized Channel

Press EXIT to return

Please take note of all information on the screen (you will provide this information to your cable operator). Call your cable operator

and give them the information from the card to start your cable service.

NOTES: 1. A digital cable subscription is required.

2. Antenna B will not be available when CableCARD is inserted.

3. Do not insert a PCMCIA card into the CableCARD slot.

REAR PANEL CONNECTIONS

TYPICAL FULL-FEATURE SETUP

DVD Player

OUTPUT

P /C P /C

Outside antenna or

digital cable

External Digital

Component with

HDMI output

capability

CableCARD

(Top of card faces right)

ANT A

HDMI

OUT

HDMI 1

INPUT 2

VIDEO

INPUT 1

VIDEO

ANT B

INPUT 4

MONITOR OUT

S-VIDEO

INPUT 3

To an amplifier/receiver

with optical input capability.

OPTICAL OUT

Digital Audio

Upgrade Card

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

VIDEO

AUDIO

(MONO)

RS232C

TV AS CENTER

AUDIO

TO HI-FI

INPUT

OUTPUT

S-VIDEO

VCR #1

VCR #2

Laserdisc player, VCR,

camcorder, etc.

Connect only 1 component to each input jack.

2. Follow connections that pertain to your personal entertainment system.

3. Inputs 1 and 2 can accomodate Composite and Component video signals.

NOTES: 1.

4. Cables are not included with the purchase of this TV, except when noted as “provided”.

TIPS ON REAR PANEL CONNECTIONS

•

S-VIDEO, Y-PbPr and HDMI connections are provided for high performance laserdisc players, VCRs etc. that have this feature.

Use these connections in place of the standard video connection if your device has this feature.

•

If your device has only one audio output (mono sound), connect it to the left audio jack on the television.

Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.

A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output (INPUT: 3 in

the example on page 12). Refer to your VCR operating guide for more information on line input-output connections.

•

You may use VIDEO or S-VIDEO inputs to connect to Input 3, Input 4 or Input 5, but only one of these may be used at a time.

Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack.

COMPONENT:Y-P P (Input 1 & 2) connections are provided for high performance components, such as DVD players and set-

B R

top-boxes. Use these connections in place of the standard video connection if your device has this feature. Input 2 accepts

both composite and component video signals.

•

Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s P input

and the components R-Y output to the TV’s P input.

Your component outputs may be labeled Y-C C . In this case, connect the components C output to the TV’s P input and

B R

the components C output to the TV’s P input.

•

You may use composite and component video signals for Inputs 1 and 2.

It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-P P inputs (see page 37).

B R

Y-P P

To ensure no copyright infringement, the MONITOR OUT output may be abnormal, when using the

jacks.

B R

•

When using an HDMI input from a Set-Top-Box, it is recommended that a 1080i or 720p input signal is used.

CONNECTING EXTERNAL AUDIO SOURCES

Match the numbers below to the diagram for speaker placement.

ᕃ The television’s internal speakers will act as center speaker (select Audio-Internal Speakers-TV as Center).

ᕄ These FRONT left and right speakers are connected to the FRONT output of a separate audio amplifier.

ᕅ These REAR left and right speakers are connected to the REAR output of a separate audio amplifier.

ᕆ This subwoofer is connected to the LFE/Sub Out output of a separate audio amplifier.

REAR PANEL OF TELEVISION

CableCARD

(Top of card faces right)

ANT A

HDMI 1

INPUT 2

VIDEO

INPUT 1

VIDEO

ANT B

INPUT 4

MONITOR OUT

S-VIDEO

INPUT 3

OPTICAL OUT

Digital Audio

Upgrade Card

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

VIDEO

AUDIO

(MONO)

TV AS CENTER

RS232C

AUDIO

TO HI-FI

CENTER

OUT

OPTICAL

INPUT

Stereo System Amplifier

or DVD Player

NOTES:

1. The Optical Out (Digital Audio) provides a fixed digital audio output to your external component such as an A/V

receiver with optical input capability. The audio level can only be controlled through the volume control of the

external audio amplifier.

2. See page 42 for AUDIO-Digital Output.

CONNECTING EXTERNAL VIDEO SOURCES

The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is

dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and

audio inputs and outputs.

The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your particu-

lar assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded

wire.

Before Operating External Video Source

Connect an external source to the INPUT terminal, then press the INPUTS button to show the INPUTS menu. Use the CURSOR PAD

to select the Antenna and Input of your choice. Then press the SELECT button to confirm your choice (see page 24).

Input 5

Ant B

Ant A

Input 1

Input 2

SEL

Move

Sel

NOTE:

When the TV is set to VIDEO and a video signal is not received from the VIDEO INPUT JACK on the back panel

of the TV (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the set will appear to be OFF.

CONNECTING A MONAURAL AUDIO SOURCE TO INPUT1~INPUT5

1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set

below.

2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.

3. Press the INPUTS button, then select INPUT 1 from the INPUTS menu to view the program from the VCR or the laserdisc player.

The VIDEO OSD label disappears automatically after approximately four seconds.

4. Select Antenna from the INPUTS menu to return to the previous channel.

CableCARD

(Top of card faces right)

ANT A

HDMI 1

INPUT 2

VIDEO

INPUT 1

VIDEO

ANT B

INPUT 4

MONITOR OUT

S-VIDEO

INPUT 3

OPTICAL OUT

Digital Audio

Upgrade Card

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

VIDEO

AUDIO

(MONO)

RS232C

TV AS CENTER

AUDIO

TO HI-FI

Audio Video

OUTPUT

VCR

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A STEREO SOURCE TO INPUT1~INPUT5

Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set

below.

Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

Press the INPUTS button, then select INPUT 3 from the INPUTS menu to view the program from the VCR or laserdisc player.

The VIDEO OSD label disappears automatically after approximately four seconds.

Select Antenna from the INPUTS menu to return to the previous channel.

CableCARD

(Top of card faces right)

ANT A

HDMI 1

INPUT 2

VIDEO

INPUT 1

VIDEO

ANT B

INPUT 4

MONITOR OUT

S-VIDEO

INPUT 3

OPTICAL OUT

Digital Audio

Upgrade Card

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

VIDEO

AUDIO

(MONO)

RS232C

TV AS CENTER

AUDIO

TO HI-FI

OUTPUT

VCR

NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. A single VCR can be used for VCR #1 and VCR #2 (see page 12), but note that a VCR cannot record its own video

or line output. Refer to your VCR operating guide for more information on line input-output connections.

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5

Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV

set below.

Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

Press the INPUTS button, then select INPUT 3 from the INPUTS menu to view the program from the VCR or laserdisc player.

The VIDEO OSD label disappears automatically after approximately four seconds.

Select Antenna from the INPUTS menu to return to the previous channel.

CableCARD

(Top of card faces right)

ANT A

HDMI 1

INPUT 2

VIDEO

INPUT 1

VIDEO

ANT B

INPUT 4

MONITOR OUT

S-VIDEO

INPUT 3

OPTICAL OUT

Digital Audio

Upgrade Card

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

VIDEO

AUDIO

(MONO)

RS232C

TV AS CENTER

AUDIO

TO HI-FI

S-VIDEO

VCR

NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. A single VCR can be used for VCR #1 and VCR #2 (see page 12), but note that a VCR cannot record its own video

or line output. Refer to your VCR operating guide for more information on line input-output connections.

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A COMPONENT SOURCE WITH HDMI or DVI CAPABILITY TO INPUT 1

1. Connect the HDMI or DVI to HDMI connection cable from the output of the HDTV set top box or DVD player to the HDMI input as

shown on the TV set below. When using a component with DVI output, you also have to connect the AUDIO OUT (R/L) of the

component to the AUDIO IN (R/L) of INPUT 1.

2. Press the INPUTS button, then select INPUT 1 from the INPUTS menu to view the program from the HDTV set top box or DVD

player. The VIDEO OSD label disappears automatically after approximately four seconds.

3. Select Antenna from the INPUTS menu to return to the previous channel.

DVI-HDMI

HDMI-HDMI

CableCARD

(Top of card faces right)

CableCARD

(Top of card faces right)

ANT A

HDMI 1

INPUT 2

VIDEO

INPUT 1

VIDEO

INPUT 2

VIDEO

INPUT 1

VIDEO

ANT B

MONITOR OUT

S-VIDEO

INPUT 4

INPUT 3

MONITOR OUT

S-VIDEO

INPUT 4

INPUT 3

OPTICAL OUT

Digital Audio

Upgrade Card

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

VIDEO

AUDIO

VIDEO

AUDIO

(MONO)

RS232C

TV AS CENTER

AUDIO

TO HI-FI

AUDIO

TO HI-FI

HDMI Cable

DVI to HDMI

Cable

HDMI Output

DIGITAL OUTPUT

AUDIO OUT

DVD Player or HDTV STB

NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. The HDMI input on INPUT 1 contains the copy protection system called High-bandwidth Digital Content

Protection (HDCP). HDCP is a cryptographic system that encrypts video signals when using HDMI connections to

prevent illegal copying of video contents.

3. HDMI is not a “NETWORK” technology. It establishes a one-way point-to-point connection for delivery of

uncompressed video to a display.

4. The connected digital output device controls the HDMI interface so proper set-up of device user settings determines

final video appearance.

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A COMPONENT SOURCE TO INPUT 1 OR 2: Y-P P .

B R

Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV

set below.

Connect the cable from the C /P OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (P jack.

Connect the cable from the C /P OUT or R-Y OUT of the laserdisc/DVD player or HDTV set top box to the INPUT (P ) jack.

Connect the cable from the AUDIO OUT R of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/R) jack.

Connect the cable from the AUDIO OUT L of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/L) jack.

Press the the INPUTS button, then select INPUT 2 from the INPUTS menu to view the program from the Laserdisc/DVD player

or HDTV set top box. The VIDEO OSD label disappears automatically after approximately four seconds.

Select Antenna from the INPUTS menu to return to the previous channel.

CableCARD

(Top of card faces right)

ANT A

HDMI 1

INPUT 2

VIDEO

INPUT 1

VIDEO

ANT B

INPUT 4

MONITOR OUT

S-VIDEO

INPUT 3

OPTICAL OUT

Digital Audio

Upgrade Card

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

VIDEO

AUDIO

(MONO)

RS232C

TV AS CENTER

AUDIO

TO HI-FI

OUTPUT

DVD Player

NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. See page 13 for tips on REAR PANEL CONNECTIONS.

THE REMOTE CONTROL

In addition to controlling all the functions on your HITACHI Projection TV, the new remote control is designed to operate different

types of VCRs, CATV (Cable TV) converters, set-top-boxes, satellite receivers (SAT) and DVD players with one touch. Basic oper-

ation keys are grouped together in one area.

To operate your TV, point the remote control at the screen of the TV and press the TV button. The remote will now control your

television.

To operate your VCR, point the remote at the remote sensor of the VCR and press the VCR button. The remote will now control

your VCR (see page 32 for instructions on how to program the remote to control your VCR).

To operate your cable box, point the remote at the remote sensor of the cable box and press the CABLE (CBL) button. The remote

will now control your cable box (see page 29 for instructions on how to program the remote to control your cable box).

To operate your set-top-box or satellite receiver, point the remote at the remote sensor of the set-top-box or satellite receiver and

press the SAT button. The remote will now control your set-top-box or satellite receiver. If you have a satellite receiver, use this

button to program your satellite receiver (see page 30 for instructions on how to program the remote to control your SAT).

To operate your DVD player, point the remote at the remote sensor of the DVD player and press the DVD button. The remote will

now control your DVD player (see page 31 for instruction on how to program the remote to control your DVD

player).

HOW TO USE THE REMOTE TO CONTROL YOUR TV

ቢ

ባ

ብ

ቧ

ቦ

ቩ

ቨ

ቫ

ቭ

ተ

ቪ

ቮ

ቯ

ተ

ቲ

ቤ

ቱ

ታ

ቢ POWER button

Press this button to turn the TV set on or off when the remote is in TV mode. (See page 20 for instructions on how to set the remote

control to TV mode.)

ባ MODE buttons

These buttons allow the remote to control your TV, VCR, DVD, Cable box/Satellite box depending on which button is pressed.

ቤ PAUSE button

Press the PAUSE button to freeze the picture. Press the EXIT button to return the picture to motion. Press the PAUSE button

repeatedly to cycle through the three different freeze modes (see page 28).

Freeze

ብ DAY/NIGHT button

Press this button to toggle between Day and Night picture mode settings. Select Day for day time viewing with more brightness and

contrast to compete with room light. Select Night for night time viewing with less brightness and contrast for a more detailed picture

(see page 36 for settings changes).

HOW TO USE THE REMOTE TO

CONTROL YOUR TV

ቦ ASPECT button

Press this button to quickly change the picture format ASPECT ratio.

Depending on the input signal format received, the picture format ratio allows you to adjust the images through the following options.

4:3 STANDARD

Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the

left and right of the image to preserve the original aspect ratio of the source. Note: Use this mode for

only 15% of your total viewing time to prevent uneven aging of the phosphors. Phosphors in the lighted

area of the picture will age more rapidly than the gray areas.

4:3 EXPANDED

Use this aspect mode to display conventional (4:3) sources by linearly increasing image expansion from

the center towards the edges of the display area in order to fill it.

4:3 Zoom1/Zoom2

16:9 STANDARD

Use these aspect modes to zoom in on conventional (4:3) sources.

Use this aspect mode to display 16:9 sources like HDTV and DVD’s preserving the original 16:9 aspect

ratio.

16:9 Zoom

Use this aspect to Zoom-in once while in 16:9 aspect.

(1) NTSC/480i/480P Input

4:3

INPUT

4:3 STANDARD

4:3 EXPANDED

4:3 ZOOM1

4:3 ZOOM2

16:9 ZOOM

16:9 STANDARD

(2) 480i/480P Input

16:9

INPUT

4:3 STANDARD

4:3 EXPANDED

4:3 ZOOM1

4:3 ZOOM2

16:9 ZOOM

16:9 STANDARD

(3) HDMI/720P/1080i Input

16:9

16:9 STANDARD

16:9 ZOOM

4:3 EXPANDED

INPUT

NOTES:

1. The Aspect Style setting you select for an ANT input will automatically be set for the other ANT input. However, all

five video inputs have independent Aspect Style settings.

2. Vertical position adjustments are directly available when you choose 4:3 EXPANDED/ZOOM1/ZOOM2 or 16:9

ZOOM aspect style (see also page 43).

HOW TO USE THE REMOTE TO

CONTROL YOUR TV

ቧ INPUTS button

When the remote control is in TV mode, press this button to access the INPUTS menu. Use the CURSOR and SELECT buttons to

select the inputs that are being used. Pressing the INPUTS button repeatedly will also cycle through the Inputs menu items. Then

press the SELECT button to select.

Input 5

Ant B

Ant A

Input 1

Input 2

SEL Select

Move

Select to choose Antenna B.

Select to choose Antenna A.

Ant B

Ant A

Select to choose Input 1 for Video 1.

Select to choose Input 2 for Video 2.

Select to choose Input 3 for Video 3.

Input 1

Input 2

Input 3

Select to choose Input 4 for Video 4.

Select to choose Input 5 for Video 5.

Input 4

Input 5

HOW TO USE THE REMOTE TO

CONTROL YOUR TV

ቨ PICTURE-IN-PICTURE button

See separate section on pages 26-28 for a description.

ቩ MENU button

The MENU button will start the On-Screen Display.

ቪ GUIDE button [Cable Box (CBL), Satellite Receiver (SAT)/Set-Top-Box (STB) mode only]

The use of this button is only applicable when the remote control is in (CBL) and (SAT/STB) mode. Press this button to access the

Channel Guide of the (CBL), and (SAT/STB).

ቫ EXIT button

This button will exit all On-Screen Displays.

ቭ CURSOR buttons/SELECT button

All the On-Screen Display features can be set or adjusted by using the CURSOR buttons and the SELECT button, except for

numeric entries. Press the CURSOR buttons toward desired direction and press the SELECT button to select.

ቮ INFO button

Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second

audio program (SAP), the time, CHANNEL ID and if the TIMER is set.

ANALOG CHANNELS

Time

3:32 PM

Ant A 22

ST Stereo

Main Picture Source

Audio Broadcast

Broadcast Rating

INFO

Aspect

Mode

Closed

Captioning

Day/Night

Mode

Day

_View--:-- AM

Off

--:-- PM

4:3 Expanded

Event Timer

DIGITAL CHANNELS

TV Time

3:32PM

Picture Source

Ant A 122-1

KPBS-DT

Engl

TV-Y

720p Format

Channel ID

3:32 PM

Program Language

No Info

Broadcast Rating

Signal Format

INFO

Closed

Captioning

Aspect Mode

Day/Night

Mode

Day

Off

4:3 Expanded

--:-- AM

_View--:-- AM

--:-- PM _REC--:-- AM

INFO Return

Event Timer

Timer Recording

3:32 PM

S-IN: 3

VID 3

When an S-VIDEO

Input is connected to

VIDEO: 3.

INFO

3:32 PM

YPBPR: 1

VID: 1

When a

COMPONENT

VIDEO:Y-P P Input

is connected to

VIDEO: 1.

INFO

B R

NOTES: 1. The Sleep Timer info will show momentarily after releasing INFO button.

2. Press the INFO button again or the EXIT button to return to normal viewing.

HOW TO USE THE REMOTE TO

CONTROL YOUR TV

ቯ VOLUME (VOL), MUTE button

Press the VOLUME button (̆ or ̄) until you obtain the desired sound level.

To reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc., press the MUTE button. Press the

MUTE button again to turn the sound off completely (MUTE). To restore the sound, press the MUTE button one more time, or VOL

Up (̆).

Volume

Mute

Soft Mute 8

Closed Captioning will display automatically when MUTE/SOFT MUTE is on and Closed Caption is set to AUTO (see page 62).

When the TV power is turned off at a volume level 31 or greater, the volume level will default to 30 when the TV is turned on.

However, if it is set to a level 30 or less, the volume level will be at the level it was set when the TV is turned ON.

ተ CHANNEL SELECTOR/FAVORITE CHANNEL (FAV CH) buttons

The CHANNEL SELECTOR buttons are used to select channels, lock access code, etc. Use the CHANNEL SELECTOR buttons

to enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel

you wish to tune then wait a few seconds for the TV to tune. Channel selection may also be performed by CHANNEL (CH) up (̆)

or CHANNEL (CH) down (̄).

Press the FAV CH button to switch to Favorite (FAV) channel mode. You will know you are in Favorite Channel mode when (FAV)

is displayed and the displayed channel is GREEN. Press it again to return to your regular tuned channels. You can add any chan-

nel to your Favorite channel list by pressing and holding down the FAV CH button until the displayed channel turns from WHITE to

highlighted GREEN. You can also delete a channel from your favorite channel list by pressing and holding down the FAV CH but-

ton until the displayed channel turns highlighted GREEN to WHITE.

Ant A 22

FAV Ant A 22

ቱ (-) DASH button

The (-) DASH button can only be used when the remote control is in Satellite (SAT) mode.

ቲ LAST CHANNEL (LC) button

Press this button to toggle between the current and last channel viewed.

ታ RECORD button

Press twice (2 times) to record programs when the remote is in VCR mode.

PICTURE-IN-PICTURE (PIP)

Your HITACHI Projection TV incorporates Two Tuner technology designed for improved viewing enjoyment. This Two Tuner feature allows

you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each.

ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture.

To select between main picture and PIP sub-picture tuning, use the CURSOR buttons on the remote. The white highlighted channel

display will move with every press of the CURSOR buttons (̇, ̈).

The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV

program while viewing other programs from any of the video inputs.

CableCARD

(Top of card faces right)

ANT A

ቢ

HDMI 1

INPUT 2

VIDEO

INPUT 1

VIDEO

ANT B

INPUT 4

MONITOR OUT

S-VIDEO

INPUT 3

OPTICAL OUT

Digital Audio

Upgrade Card

Apparatus Claims of U.S. Patent Nos.

4,631,603; 4,577,216; 4,819,098;

4,907,093; and 6,381,747 licensed

for limited viewing uses only.

VIDEO

AUDIO

(MONO)

RS232C

TV AS CENTER

AUDIO

TO HI-FI

Audio Video

OUTPUT

ባ

VCR

Use above connection to view VCR program as a sub-picture while viewing another program as main picture (ANT A, ANT B,

INPUT:2, INPUT:3, INPUT:4, or INPUT:5). You may also view the VCR program as a main picture while viewing another program

as a sub-picture (ANT A, INPUT:2, INPUT:3, INPUT:4 or INPUT:5).

When installing a CableCARD, connect your coaxial cable to ANT A (see page 11). ANT B will not be available while using a

CableCARD.

ቢ PIP button

Press the PIP button and a sub-picture will appear in one of the four different modes (POP, PIP, SPLIT or SURF), depending on the

INPUT signal. To change the PIP mode, use the PIP button to cycle through the four different modes.

POP MODE PICTURE-IN-PICTURE

POP Mode PIP displays the sub-picture outside of the main picture. Use the CURSOR buttons (̆, ̄) to move the sub-picture.

This feature is not available with a 1080i signal. Please refer to the PICTURE-IN-PICTURE MODES Table (see page 27).

Main Picture

Sub Picture

NOTES: 1. PIP MODE Picture-in-Picture is only available with a 1080i signal.

2. Press the CURSOR buttons (̇, ̈) to enable the sub-picture sound.

3. Sub-picture channel availability depends on the channel list.

PICTURE-IN-PICTURE (PIP)

PIP MODE PICTURE-IN-PICTURE

This feature is only available with a 1080i signal. To prevent a pattern burn, occasionally move the sub-picture using the CURSOR

buttons.

Main Picture

Sub Picture

SPLIT MODE PICTURE-IN-PICTURE

Split Mode PIP displays the main picture and sub-picture evenly on the screen.

Sub Picture

Main Picture

SURF MODE PICTURE-IN-PICTURE

Surf Mode PIP automatically scans all active channels (those set in memory) and displays them as PIP sub-pictures or

Thumbnail channels. Press the SELECT button to stop on a chosen channel. Use the remote CURSOR buttons (̇, ̈, ̆, ̄)

to navigate the Thumbnail. Press the EXIT button to enable your chosen channel and return to normal viewing.

NOTE:

Press the SELECT button to stop the Surf mode or channel scan. Press the SELECT button again to resume Surf

mode or channel scan.

PICTURE-IN-PICTURE (PIP) MODES

Sub

Main

PIP Mode

POP

NTSC 480i

480p 720p 1080i

NTSC

Yes

480i

1080i

NTSC

480i

PIP 4x3

PIP 16x9

SPLIT

Yes

480p

720p

1080i

12 Pix

PICTURE-IN-PICTURE (PIP)

ባ PAUSE button

If you wish to freeze the sub-picture, press the PAUSE button. This is convenient when trying to write down the address for a

mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the EXIT button. Press

the PAUSE button repeatedly to toggle between FREEZE modes (Main Freeze, SPLIT and STROBE).

Freeze

MAIN FREEZE

Press the PAUSE button to freeze one frame of the picture you are currently viewing and the frozen frame will show in the Main

Picture. Press the EXIT button to return to normal viewing. This feature is useful for freezing a picture frame with addresses.

Hot Springs Clay Mask

C/O John Doe

Run-Spa Retreat

P.O. Box 55512

Any Town, USA 98765

Check or

Money Order Only

1-800-555-1212

SPLIT FREEZE

Press the PAUSE button to freeze the picture you are currently viewing (only the right sub-picture will freeze). Press the EXIT button

to return to normal viewing.

Sub Picture

Main Picture

STROBE FREEZE

Press the PAUSE button to freeze three frames of the picture you are currently viewing (only the 3 sub-pictures will freeze). Press

the EXIT button to return to normal viewing. This feature is useful for viewing a moving picture that has many details, for example,

a close play in a sporting event or a golf swing.

FREEZE

NOTES: 1. The default FREEZE mode is the MAIN freeze followed by the SPLIT freeze and then the STROBE freeze. The last

Freeze mode you selected before you pressed the EXIT button will be the one that comes up after pressing the

PAUSE button again.

2. Each freeze frame is delayed about 0.1 (1/10) second.

3. Strobe Freeze is not available in 480p/720p/1080i inputs.

USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS

Operating the precoded function for your cable box.

This remote is designed to operate different types of cable boxes.You must first program the remote to match the remote system of your

cable box (refer below for pre-codes).

1. Turn ON your cable box.

2. Aim the remote control at the front of your cable box.

ባ

3. To switch to Cable (CBL) pre-coded mode, press and release the

ቢ

CABLE (CBL) button.

4. Hold down the CBL button on the remote and enter the two digit preset

ቤ

code that matches your cable box, as shown below. Release the CBL

button.

ባ

5. Aim the remote at the cable box and press the POWER button. The

remote will turn off your cable box when the correct two digit preset code

is entered. When this occurs, the remote control is programmed for your

cable box. If the cable box does not turn off, try a different two digit pre-

set code.

6. The remote will now control your Cable box.

ቤ

NOTES:

1. If your cable box cannot be operated after performing the

above procedures, your cable box code has not been

precoded into the remote.

ባ

2. In the unlikely event that your cable box cannot be

operated after performing the above procedures, please

consult your cable box operating guide.

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

ቢ CABLE (CBL) button

This button allows the remote to control your cable box by

setting it to CABLE mode.

ባ PRECODED CABLE BOX buttons

These buttons transmit the chosen precoded cable codes.

ቤ EXCLUSIVE TV buttons

These buttons are for operating the TV.

CABLE BRAND . . . . . . . . . . . . . . . . .CODES

HAMLIN . . . . . . . . . . . . . . . . . . .22, 23, 24, 25

JERROLD . . . . . . . . . . . . . . . . 00, 01, 02, 03,

. . . . . . . . . . . . . . . . . . . . . . . . . .04, 05, 06, 07

OAK . . . . . . . . . . . . . . . . . . . . . . . . .26, 27, 28

PANASONIC . . . . . . . . . . . . . . . . . . 18, 19, 20

PIONEER . . . . . . . . . . . . . . . . . . . . . . . .13, 14

SCIENTIFIC ATLANTA . . . . . . . . . .08, 09, 10

TOCOM . . . . . . . . . . . . . . . . . . . . . . . . .15, 16

ZENITH . . . . . . . . . . . . . . . . . . . . . . . . .11, 12

MY CABLE BOX CODE IS:

NOTE:

Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box.

USING THE REMOTE TO CONTROL

SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS

Operating the precoded function for your set-top-box/satellite receiver.

This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the

remote system of your set-top-box/satellite systems (refer below for pre-codes).

1. Turn ON your set-top-box/satellite systems.

2. Aim the remote control at the front of your set-top-box/satellite systems.

3. To switch to set-top-box/satellite (STB) pre-coded mode, press and release the SAT button.

4. Hold down the SAT button on the remote and enter the two digit preset code that matches your set-top-box/satellite receiver, as

shown below. Release the SAT button.

5. Aim the remote at the set-top-box/satellite receiver and press the

POWER button. The remote will turn off your set-top-box/satel-

lite receiver when the correct two digit preset code is entered.

When this occurs, the remote control is programmed for your

set-top-box/satellite receiver. If the set-top-box/satellite receiver

does not turn off, try a different two digit preset code.

ባ

ቤ

ቢ

ባ

6. The remote will now control your set-top-box/satellite receiver.

NOTES:

1. If your set-top-box/satellite receiver cannot be operated

after performing the above procedures, your set-top-

box/satellite receiver code has not been precoded into the

remote.

2. In the unlikely event that your set-top-box/satellite

receiver cannot be operated after performing the above

procedures, please consult your set-top-box/satellite

receiver operating guide.

ቤ

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

ባ

ቢ SAT (Set-Top-Box/Satellite) button

This button allows the remote to control your set-top-

box/satellite receiver by setting it to SET-TOP-BOX/SATEL-

LITE mode.

ባ PRE-CODED SET-TOP-BOX/SATELLITE RECEIVER

buttons

These buttons transmit the chosen pre-coded set-top-

box/satellite codes.

ቤ EXCLUSIVE TV buttons

These buttons are for operating the TV.

SATELLITE BRAND . . . . . . . . . . . . . .CODES

ECOSTAR . . . . . . . . . . . . . . . . . . . . . . . . . .03

HITACHI . . . . . . . . . . . . . . . . . . . . . . . . . . . 00

HUGHES . . . . . . . . . . . . . . . . . . . . . . . . . . .04

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .01

SONY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .02

SET TOP BOX BRAND . . . . . . . . . . .CODES

PANASONIC . . . . . . . . . . . . . . . . . . . . . . . .05

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06

SAMSUNG . . . . . . . . . . . . . . . . . . . . . . . . . .07

ZENITH . . . . . . . . . . . . . . . . . . . . . . . . . . . .08

MY SATELLITE RECEIVER/STB CODE IS:

NOTE:

Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-top-

box/satellite receiver.

USING THE REMOTE TO CONTROL DVD FUNCTIONS

Operating the precoded function for your DVD player.

This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of

your DVD player (refer below for pre-codes).

1. Turn ON your DVD player.

2. Aim the remote control at the front of your DVD player.

3. To switch to DVD pre-coded mode, press and release the DVD button.

4. Hold down the DVD button on the remote and enter the two digit preset code that matches your DVD player, as shown below.

Release the DVD button.

5. Aim the remote at the DVD player and press the POWER button. The

remote will turn off your DVD player when the correct two digit preset

code is entered. When this occurs, the remote control is programmed

for your DVD player. If the DVD player does not turn off, try a different

ባ

two digit preset code.

ቢ

6. The remote will now control your DVD player.

ቤ

7. You will need to set the display type of your DVD player to 16:9

widescreen.

ባ

NOTES:

1. If your DVD player cannot be operated after performing

the above procedures, your DVD player’s code has not

been precoded into the remote.

2. In the unlikely event that your DVD player cannot be

operated after performing the above procedures, please

consult your DVD player operating guide.

ቤ

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

ባ

ቢ DVD button

This button allows the remote to control your DVD player by

setting it to DVD mode.

ባ

ባ PRECODED DVD Buttons

These buttons transmit the chosen precoded DVD codes.

ቤ EXCLUSIVE TV Buttons

These buttons are for operating the TV.

DVD BRAND . . . . . . . . . . . . . . . . . . . .CODES

APEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

GO VIDEO . . . . . . . . . . . . . . . . . . . . . . . . . 09

HITACHI . . . . . . . . . . . . . . . . . . . . . . . . . . . .00

KENWOOD . . . . . . . . . . . . . . . . . . . . . . . . .11

PANASONIC . . . . . . . . . . . . . . . . . . . . . . . .02

PIONEER . . . . . . . . . . . . . . . . . . . . . . . . . . 03

DVD BRAND . . . . . . . . . . . . . . . . . . . .CODES

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04

SAMSUNG . . . . . . . . . . . . . . . . . . . . . . . . . .06

SANYO . . . . . . . . . . . . . . . . . . . . . . . . . . . . .07

SONY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .01

TOSHIBA . . . . . . . . . . . . . . . . . . . . . . . . . . .05

MY DVD PLAYER CODE IS:

NOTE:

Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player.

USING YOUR REMOTE

TO CONTROL VCR FUNCTIONS

Operating the precoded function for your VCR.

This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR

(refer below for pre-codes).

1. Turn ON your VCR.

2. Aim the remote control at the front of your VCR.

3. To switch to VCR pre-coded mode, press and release the VCR button.

4. Hold down the VCR button on the remote and enter the two digit preset code that matches your VCR, as shown below. Release

the VCR button.

5. Aim the remote at the VCR and press the POWER button. The

remote will turn off your VCR when the correct two digit preset code

is entered. When this occurs, the remote control is programmed for

your VCR. If the VCR does not turn off, try a different two digit pre-

set code.

ባ

ቢ

ቤ

6. The remote will now control your VCR.

ቤ

NOTES:

1. If your VCR cannot be operated after performing the

above procedures, your VCR’s code has not been

precoded into the remote.

2. In the unlikely event that your VCR cannot be operated

after performing the above procedures, please consult

your VCR operating guide.

ቤ

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

4. Press the Record button twice to record.

ባ

ቢ VCR button

This button allows the remote to control your VCR player by

setting it to VCR mode.

ባ PRECODED VCR Buttons

These buttons transmit the chosen precoded VCR codes.

ቤ EXCLUSIVE TV Buttons

These buttons are for operating the TV.

VCR BRAND . . . . . . . . . . . . . . . . . . .CODES

EMERSON . . . . . . . . . . . . .20, 21, 22, 23 ,24

FISHER . . . . . . . . . . . . . . . . . . 34, 37, 38, 39

HITACHI . . . . . . . . .00, 01, 02, 03, 04, 05, 06

JVC . . . . . . . . . . . . . . . . . . . . . . . . .49, 50, 51

MAGNAVOX . . . . . . . . . . . . . . . . . . . . . .12, 13

MITSUBISHI . . . . . . . . . . . . . . . 27, 28, 29, 30

VCR BRAND . . . . . . . . . . . . . . . . . . .CODES

NEC . . . . . . . . . . . . . . . . . . . . . . . . . . . 40, 41

PANASONIC . . . . . . . . . . . . . . . . . . . . .10, 11

SAMSUNG . . . . . . . . . . . . . . . . . . . . . . .25, 26

SHARP . . . . . . . . . . . . . . . . . . . . . . . . .31, 32

SONY . . . . . . . . . . . . . . . . . . . . . . . .07, 08, 09

MY VCR CODE IS:

NOTE:

Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR.

ON-SCREEN DISPLAY (OSD)

1. Press MENU on the remote control to display the different features on your HITACHI Projection TV.

2. Press the CURSOR buttons to navigate and highlight a different feature of the On-Screen Display menu. Press the SELECT button

to select.

3. Press EXIT on the remote control to quickly exit from a menu.

This part of the screen shows

which selections are available.

Video

Audio

Aspect

Chan. Manager

Locks

Timers

Setup

SEL

Move

Sel

This part of the screen shows

which Remote Control buttons

to use.

ON-SCREEN DISPLAY (OSD)

Picture Mode

Contrast

Select between the two picture modes; Day and Night.

Adjust contrast.

Brightness

Color

Adjust brightness.

Adjust color.

Tint

Adjust tint.

Sharpness

Color Temperature

Adjust sharpness.

Set this to High for less intense color with more blue, set to Medium

for natural color, set to Standard for standard colors or Black and

White for more reddish color.

Black Enhancement

Edge Enhancement

Reset Video Settings

Color Management

Enhance picture brightness in light scenes.

Automatically enhances the edges between light and dark areas.

Choose the Reset Video settings.

Adjust and balance individual colors to make either deeper or more

pure according to preference.

Video

Color Decoding

Auto Color

Adjust the percentage of Red, Green and Color according to preference.

The AUTO COLOR function automatically monitors and adjusts the

color to maintain natural flesh tones while preserving fidelity of background

colors.

Noise Reduction

Auto Movie Mode

Reduces conspicuous noise in the picture.

Turn ON/OFF the 3:2 Pulldown detection feature.

Treble

Adjust the treble.

Bass

Adjust the bass.

Balance

Adjust the balance.

SRS

BBE

Select SRS settings (Off, Wide, Normal)

Select BBE settings (Off, Soft, Hard)

Select between three Audio Sources.

Select internal or external speakers.

Eliminates the noise between stations.

Adjust volume in fixed setting.

Adjust Loudness.

Select Language options if available.

Select Optical Output options.

Select Dynamic Range Compression to ON or OFF.

Audio Source

Internal Speakers

Auto Noise Cancel

Perfect Volume

Loudness

Language

Digital Output

DRC

Audio

4:3 Standard

4:3 Expanded

4:3 Zoom 1

4:3 Zoom 2

16:9 Standard

16:9 Zoom

Choose the picture format aspect ratio.

Aspect

NOTE:

The Language, Digital Output, and the Dynamic Range Compression feature of the Audio OSD are only available for

Digital channels.

ON-SCREEN DISPLAY (OSD)

Set the Antenna

Auto Channel Scan

Signal Meter

Channel List

Set Antenna settings.

Set Auto Channel Scan.

Access Signal Meter.

Set Channel List.

Channel

Manager

Change Access Code

Engage Lock

TV Time Lock

Change Lock access code.

Choose to lock channel, video input, and/or front panel.

Set specific time to Lock TV.

Movie Ratings

Block various types of movies and video types based on motion

picture ratings.

TV Ratings

Block various types of movies and television programming based on a

parental guide ratings.

Locks

Canadian Ratings (ENG)

Canadian Ratings (FRN)

Block various types of movies and television programming based on

the Canadian ratings system.

Block various types of movies and television programming based on

the Canadian French ratings system.

Set the Clock

Set Clock Settings.

Set Sleep Timer

Set Day/Night Timer

Set Event Timer

Set Sleep Timer intervals (30 min. intervals, 00:30-3:00).

Set Day/Night picture mode settings.

Set viewing reservation for TV programs.

Timers

Magic Focus Tune Up

Automatic and manual alignment of the red, green and blue colors to

make white.

Menu Preference

Set The Inputs

Set Virtual HD

Set Black Side Panel

Set Closed Captions

Choose English, French, or Spanish text.

Label Video Inputs , VCR, DVD, etc.

Select between 1080i and 540p Scan mode.

Set the gray side bars on/off when watching 4:3 signals in standard mode.

Feature to display dialogue/text.

Setup

Set Monitor Out

Set Monitor Out source.

Information display for this TV.

Select to access CableCARD information.

Select to set RS232C feature.

Select to upgrade TV software.

About Your TV

CableCARD Info

Set AV Control

Upgrades

Quick Start Up

Select the TV Quick Start Up options.

NOTES: 1. The Signal Meter feature of the Channel Manager OSD is only available for Digital signals.

2. The CableCARD information feature of the Setup OSD is only available when a CableCARD from your cable

operator is installed in the rear panel of the TV.

VIDEO

Select VIDEO to adjust picture settings and improve picture quality. You can independently customize each of the

Video Inputs to your preference to increase viewing performance and pleasure depending upon the video program

being viewed. If RESET is selected, only the selected input will reset to initial conditions.

Video

Picture Mode

Use this function to choose from automatic picture settings to optimize your TV’s performance.

Video

Audio

Aspect

Chan. Manager

Locks

Timers

Setup

SEL

Move

Sel

ANT A/B

Day

Video

Picture Mode

Contrast

Night

100%

50%

Brightness

Color

50%

Tint

Sharpness

50%

High

Color Temperature

Black Enhancement

Edge Enhancement

Reset Video Settings

Middle

High

Picture Mode

Day Night

SEL Return

Next/Prev

Select

SEL Return

Move

Use the CURSOR buttons ̇ or ̈ to highlight and select Picture Mode settings.

Function

Contrast

Day

Night

Reset

Reset the video

menu settings on

current input

100%

50%

High

70%

55%

50%

40%

Brightness

Color

automatically

to Day Mode.

Tint

Sharpness

Color Temperature

Black Enhancement

Edge Enhancement

Auto Color

Standard

Low

Off

Middle

High

Off

Noise Reduction

Off

Color Management

(Set User Colors)

Auto Movie Mode

Off

(TV/Cinema Detection)

Press EXIT to quit menu or select PICTURE MODE to return to previous menu.

VIDEO

Use the CURSOR buttons ̆ or ̄ to highlight the function to be adjusted.

Press the CURSOR buttons ̇ or ̈ to adjust the function. Press the SELECT button to select the function settings.

Press MENU to return to main menu or select PICTURE MODE to return to previous menu.

Press EXIT to quit menu.

Use this function to change the contrast between black and white levels in the picture.

Use this function to adjust overall picture brightness.

Contrast

Brightness

Color

Use this function to adjust the level of color in the picture.

Use this function to adjust flesh tones so they appear natural.

Tint

Use this function to adjust the amount of fine detail in the picture. Sharpness function will be disabled

when Noise Reduction is set to High.

Sharpness

Set this to High for cooler color with more blue, set to Medium for more natural color, set to Standard for

accurate color or set to Black/White for more reddish color.

Color Temperature

Use this function to enhance Picture brightness in light scenes using the settings off, low, middle and

high.

Black Enhancement

Edge Enhancement

Use this function to automatically enhance the edges between light and dark areas using the settings Off,

Low, Middle and High.

NOTES: 1. If CONTRAST is selected, you are adjusting CONTRAST. The additional menu items BRIGHTNESS, COLOR, TINT,

and SHARPNESS can be selected and adjusted in the same manner.

2. It may be necessary to adjust TINT to obtain optimum picture quality when using the COMPONENT VIDEO Y-P P

B R

input jacks.

3. ANT A and B share a Video setting. Also, each of the video inputs have their own independent settings.

VIDEO

This function allows you to Reset the Video Menu Settings of the present input and return it to the Day VIDEO

mode.

Reset Video

Settings

ANT A/B

Day

Video

Picture Mode

Video

Reset Video Settings

Night

Contrast

100%

50%

Select “Reset” to return the video

menu settings on this input to the

original factory settings.

Brightness

Color

50%

Tint

Reset

Sharpness

50%

High

Color Temperature

Black Enhancement

Edge Enhancement

Reset Video Settings

Middle

High

SEL Select

Move

SEL Select

Move

Use the CURSOR buttons to highlight functions.

Press the SELECT button to select Reset Video Settings.

Use the CURSOR button ̄ to access other video settings.

You can customize each of the Video Inputs to your preference to increase viewing performance and pleasure, depending upon the

video program being viewed. If RESET is selected, only the selected Input will reset to the initial conditions as explained above.

If RESET is selected in Video:1 Input, only Video:1 Input will return to factory conditions.

ANT A/B

Day

Video

Color Management

Video

Picture Mode

Night

Color Decoding

Auto Color

Contrast

100%

50%

Off

Brightness

Noise Reduction

Auto Movie Mode

Color

50%

Tint

SEL Select

Move

Sharpness

50%

High

Color Temperature

Black Enhancement

Edge Enhancement

Reset Video Settings

Middle

High

SEL Select

Move

Use this function to adjust and balance the listed individual colors to make them either deeper or more

pure depending on the user’s preference. Adjust the GAIN settings to make the color brighter (+) or dark-

er (-). Adjust the PHASE settings to make the colors deeper (+) or normal (-) to match real life colors.

Color Management

Video

Color Management

Color Decoding

Auto Color

Set User Colors

Off

Phase

50%

Gain

50%

Off

Noise Reduction

Auto Movie Mode

Magenta

Red

SEL Select

Move

Yellow

Green

Cyan

Blue

Reset

SEL Return

Move

Use the CURSOR buttons to highlight function.

Press the SELECT button to select User Colors setting. When the function has a “ͱ” in the box, it is ON.

Press the CURSOR buttons ̇, ̈, ̄, ̆, to highlight and adjust individual colors.

Use the CURSOR buttons to highlight and select “Reset” to return all colors to default settings.

NOTE:

When the Set User Colors box is not checked , the listed colors will be grayed out.

VIDEO

Use this function to adjust and balance the percentage of Red, Green and Blue according to the user’s

preference in each of the four color temperature settings. Use TINT to adjust flesh tones so they appear

natural.

Color Decoding

Video

Color Management

Video

Color Decoding

Auto Color

RGB

Off

Red

50%

Noise Reduction

Auto Movie Mode

Green

Color

Tint

SEL Select

Move

Reset

SEL Return

Move

Use the CURSOR buttons to highlight function.

Press the SELECT button to select from 4 menu items.

Press the CURSOR buttons ̇, ̈, ̄, ̆, to highlight and adjust Red, Green, Color and Tint.

Use the CURSOR buttons to highlight and select “Reset” to return all settings to default.

NOTE:

Color Decoding settings are independently stored in each of the 4 Color Temperature settings.

The AUTO COLOR function automatically monitors and adjusts the color to maintain natural flesh tones

while preserving fidelity of background colors.

Auto Color

NOTES: 1. When using Component, HDMI or DVI input, Auto Color will not be available (grayed out).

2. When using digital channels, Auto Color will not be available (grayed out).

The NOISE REDUCTION function automatically reduces conspicuous noise in the picture without

degrading picture quality. Set NOISE REDUCTION to OFF if the TV experiences picture blocking.

When Noise Reduction is set to High, Sharpness function is disabled (grayed out).

Noise Reduction

Auto Movie Mode

The Auto Movie Mode function turns ON or OFF the 3:2 PULLDOWN DETECTION SPECIAL FEATURE.

Theatrical movies are shot on film at 24 frames or still pictures per second, instead of 30 frames or 60 fields

like video. When film is transferred to video for television viewing, the disparity between the two frame rates

must be reconciled. This involves a process known as 3:2 pulldown.

When Auto Movie Mode is turned ON from the VIDEO menu, your Hitachi Projection Television will activate

the circuitry for this special feature to improve video performance when watching film based sources.

NOTES: 1. When using Progressive Scan Component, HDMI or DVI input (Ex. 480p, 720p, 1080i), Auto Movie Mode will not be

available (grayed out).

2. All Video settings are independent of each other based on it’s input (ANT A/B, Input 1~5, Photo Input).

AUDIO

Select AUDIO to adjust the TV to your preference and to improve the sound quality.

Audio

Treble

Video

50%

Audio

Bass

Aspect

Balance

Chan. Manager

Locks

SRS

Off

BBE

Hard

Stereo

Timers

Audio Source

Internal Speakers

Auto Noise Cancel

Perfect Volume

Loudness

Setup

SEL

Move

Sel

Off

SEL Return

Move

Change Value

Press the CURSOR buttons ̆, ̄, to select menu item.

Press the CURSOR buttons ̇ or ̈ to adjust the function.

Press the EXIT to quit the MENU, or select Audio to return to the main menu.

NOTE:

If TREBLE is selected you are adjusting treble. The additional menu items Bass and Balance can be selected and

adjusted in the same manner.

This function controls the high frequency audio to all speakers.

Treble

Bass

This function controls the low frequency audio to all speakers.

This function will control the left to right balance of the Projection TV internal speakers.

Balance

SRS

Based on the principles of the human hearing system, SRS technology delivers and exciting and realistic

3D Sound experience from just two external speakers (or) the two internal speakers of your HITACHI

Television. If your HITACHI Television is connected to an external audio system, SRS will also create an

incredible 3D sound experience from two speakers and even enhance a complete multi-speaker surround

sound system.

NOTES:

*SRS and the

Labs, Inc.

symbol are trademarks of SRS Labs, Inc. SRS technology is incorporated under license from SRS

BBE

Technology

Sound reproduction quality enhancement system. The BBE technology produces sound that is natural and

crisp from just two speakers or the two internal speakers found in your HITACHI television. If your HITACHI

television is connected to an external audio system, BBE will also create an incredible crisp sound experi-

ence from two speakers. BBE brings to the listener’s ear a more complete and accurate reproduction of

the original performance. Each voice, speaking or singing, each instrument or sound effect is presented

with its attendant harmonics or partials more clearly audible. The ear can then more easily recognize the

unique tonal colors of each sound as though the sound was being produced live.

Licensed by BBE Sound, Inc. under USP5510752 and 5736897. BBE and BBE symbol are registered trademarks of BBE

Sound, Inc. Manufactured under license from BBE Sound, Inc.

NOTES:

AUDIO

Multi-Channel Television Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural

sound) used when receiving a weak stereo broadcast or 2nd Audio Prog (SAP) which may be a secondary

language, weather report, etc.

Audio Source

The sources received will be displayed at the top right edge of the TV. The source you select will be displayed

above the sources received. See example below for each selection when both stereo and second audio are

received (monaural is always received).

STEREO SELECTED

SAP SELECTED

MONO SELECTED

3:32 PM

Ant A 10

Stereo

3:32 PM

Ant A 10

SAP

Ant A 10

Mono

This function is useful when setting up the external speakers.

ON - Select this feature if using the internal speakers only.

TV as Center - Select this feature when setting up external speakers from a separate stereo system. The

TV’s speakers will work as the center speaker.

Internal Speakers

Auto Noise Cancel

OFF - Select this feature if you prefer to use only speakers from a separate stereo system.

This function eliminates the noise between stations. If a channel is tuned and is noisy, this function will

automatically eliminate the audio for that channel.

This function will automatically adjust volume so each channel and input has the same average volume

level.

Perfect Volume

Loudness

This function turns loudness ON or OFF. It will improve the quality of both low and high frequency sounds

when listening at low volume levels.

AUDIO

Use the functions below if your TV is connected to an amplifier/receiver with optical digital input with Dolby Digital or PCM decoder

capabilities.

Audio

Treble

Audio

Language

1 [English ]

Dolby Digital

Off

45%

50%

Bass

Digital Output

Balance

DRC

SEL Return

Move

Select

Sound Enhancement

Audio Source

Internal Speakers

Auto Noise Cancel

Perfect Volume

Loudness

Off

Stereo

SEL Return

Move

Change Value

Some programs transmit more than one DTV language option. Most will have English as a default language. The

language function will allow you to select up to 4 language options (if available).

Language

Digital

Output

This function allows you to select between Dolby^®Digital and PCM.

Dolby^®Digital - Select this feature if the TV is connected to an amplifier/receiver with a Dolby^®Digital only decoder; it

will provide six independent soundtrack channels through the optical output jack (Digital Audio).

PCM - Select this feature if the TV is connected to an amplifier/receiver with a PCM only decoder; it will provide two

independent soundtrack channels through the optical output jack (Digital Audio).

*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby

Laboratories.

DRC

Dynamic Range Compression - Use this function to compress the range of sound volume. By compressing the range

of sound volume, it is possible not only to suppress the output of loud sound at night but also to raise the volume of

low sound. This is only effective when the TV is connected via the optical out (digital audio) to an amplifier/receiver

with a Dolby^®Digital decoder. The default setting is ON.

Use the CURSOR buttons ̇, ̈ to select the chosen options.

NOTE:

These functions are only available when viewing digital programs.

ASPECT

Use this function to select the Picture Format Aspect Ratio.

Aspect

Mode

16:9 Standard

4:3 Standard

4:3 Zoom1

Video

Audio

16:9 Zoom

4:3 Expanded

4:3 Zoom2

Aspect

Chan. Manager

Locks

Auto Aspect

Vertical Position

Timers

Setup

SEL

Move

Sel

SEL Return

Move

Auto Aspect

Automatically adjust the Aspect Ratio depending on the input signal to fill the screen.

Press THE CURSOR buttons ̆, ̄, ̇, ̈ to select menu item.

Press THE SELECT button to select. A “ͱ” in the box indicates that the feature is ON.

NOTES: 1. The Auto Aspect function is recommended on an input signal with VIDEO ID.

2. The Auto Aspect function is best used on composite video, S-Video, and 480i component signals.

3. See page 22 for Aspect Mode availability.

Vertical Position

This function allows you to select when aspect style is either 4:3 EXPANDED/ZOOM1/ZOOM2 or 16:9 ZOOM. Vertical position can be

changed with these modes. For example, it will be useful for centering the picture area at both the top and bottom of the picture with

480i/480P signal. Adjustable range is -10 (video center is toward bottom of screen) to +10 (video center is toward top of screen).

Press the CURSOR buttons ̆, ̄, to select menu item.

Press the CURSOR buttons ̇ or ̈ to adjust the function.

Press EXIT to quit the MENU, or press the Aspect button to return to the main menu.

NOTE:

Vertical Position will not be available in 4:3 Standard and 16:9 Standard modes.

CHANNEL MANAGER

Chan.

Manager

Select Channel Manager to set your Antenna options, run Auto Channel Scan, Check Signal Meter and Set Channel

List.

Chan. Manager

Set The Antenna

Auto Channel Scan

Signal Meter

Video

Audio

Aspect

Chan. Manager

Locks

Channel List

SEL Return

Move

Timers

Setup

SEL

Move

Sel

Press the CURSOR buttons ̆, ̄ to highlight function, the press the SELECT button to select.

This feature will select Antenna options.

Set The Antenna

Chan. Manager

Set The Antenna

Auto Channel Scan

Signal Meter

Set The Antenna

( ) Connect Cable to Ant A and

Air to Ant B

( ) Connect Cable to Ant A only

( ) Connect Air to Ant A only

Channel List

SEL Select

Move

Cable Source

Cable(1)

Cable(2)

SEL Return

Move

Press the CURSOR buttons ̆, ̄ to highlight function, the press the SELECT button to select.

NOTE: When a CableCARD is installed, antenna settings will be set automatically to “Connect Cable to Ant A only”.

Auto Channel Scan

This feature will automatically store active TV channels in Auto Channel Scan memory.

Chan. Manager

Set The Antenna

Chan. Manager

Auto Channel Scan

Signal Meter

Ant A

Ant B

Move

Auto Channel Scan

Start Clear

Channel List

SEL Select

Move

Auto Channel Scan

Start Clear

SEL Return

Press the CURSOR buttons ̆, ̄, ̇, ̈ to highlight Ant A or Ant B.

Press the CURSOR buttons ̇, ̈ to highlight the Start or Clear option.

Press the SELECT button to select.

NOTE:

When a CableCARD is installed, Auto Channel Scan will not be available.

CHANNEL MANAGER

Select Signal Meter when using an indoor or outdoor antenna. This feature will show the signal strength and peak

values of the Antenna signal to help you adjust your antenna to optimize signal reception.

Signal Meter

Chan. Manager

Set The Antenna

Auto Channel Scan

Signal Meter

Channel

Strength

Peak

Channel List

SEL Select

Move

SEL Return

Move

Use the CURSOR buttons and the SELECT button to highlight and select “close” to exit.

NOTE:

The Signal Meter will not be available (grayed out) when watching analog channels.

This function allows you to review which channels are labeled (CH ID), which have been added to Channel

Memory (SCAN), which are protected by LOCK and which are your Favorite (FAV) Channels.

Channel List

Chan. Manager

Set The Antenna

Channel (Cable)

CH#

Scan

CH ID

Lock

Auto Channel Scan

Signal Meter

FAV 4

-------

FAV

Channel List

SEL Return

Move

SEL Return

Move

Use the CURSOR buttons to navigate the Channel List.

Press the CURSOR buttons (̆, ̄) to select On or Off on the Scan column.

Press the EXIT button to return to normal viewing.

NOTE:

When a CableCARD is installed, the Channel List will be dependent on channels agreed upon by you and your cable

operator.

LOCKS

This function will block out the picture and sound of the selected channel or video input.

It can also be used to keep the TV from being viewed for a scheduled time period that you set.

Locks

The code to enter the Locks feature is a four digit access code number. The factory preset code is 0000.

Use the number buttons to enter the access code.

Video

Audio

Aspect

Please Enter Access Code

Chan. Manager

Locks

Timers

Setup

Move

[ - - - - ]

[# Keys] Enter Code

SEL

Sel

Locks

Change Access Code

Engage Lock

TV Time Lock

Movie Ratings

TV Ratings

Canadian Ratings (Eng)

Canadian Ratings (Frn)

SEL Return

Move

Use the CURSOR buttons ̆ or ̄ to highlight function and then press the SELECT button.

To change the access code number, select Change Access Code. Enter a new four digit number.

Select CHANGE ACCESS CODE to change the factory preset code (0000) to your preference.

When ENGAGE LOCK is selected, SET CHANNEL LOCK, SET INPUT LOCK, and SET FRONT PANEL LOCK can be set individually.

When SET CHANNEL LOCK is turned on, the picture and sound for the chosen channel will be blocked out.

When SET INPUT LOCK is turned on, the picture and sound for all video inputs and the picture and sound for channels 3, 4 will be

blocked out.

When FRONT PANEL LOCK is turned on, all buttons on the Front Panel will be deactivated, except the Power button.

ꢀ

When TV TIME LOCK is turned on (Ì TIME LOCK) you can set the BEGIN and END times (CURSOR button ̈) and the TV

cannot be viewed during that time period (Set clock first). Use CURSOR buttons ̆ or ̄ to highlight ONCE (TV will time out one

time only), DAILY (TV will time out every day), WEEKLY (TV will time out one time a week).

When MOVIE RATINGS is selected, you can block various types of movies and video tapes based on motion picture ratings. Picture-

in-Picture will also be blocked automatically (see page 47).

When TV RATINGS is selected, various types of television programming based on a parental guide ratings will be blocked.

Picture-in-Picture will also be blocked automatically (see page 48).

Use CANADIAN RATINGS to block various types of movies and television programs based on the two rating systems used in

Canada that you feel may be inappropriate due to its content (see pages 49-50).

If you forget your access code, use the factory code 7777 to erase your key number. This will reset the access code number back to the

factory preset 0000.

Press EXIT to quit the menu.

NOTE:

1. When using TV TIME LOCK make sure the clock is set (see page 51).

2. Text appears on the screen to indicate that TV TIME LOCK is activated.

3. If MOVIE/TV Ratings Lock function settings are ON, SURF will be deactivated.

LOCKS

Use MOVIE RATINGS to prevent viewing of any movie that you feel may be inappropriate due to

its content.

Movie Ratings

Locks

Change Access Code

Locks

Movie Ratings

Engage Lock

Status

Not Rated:

TV Time Lock

PG:

Movie Ratings

TV Ratings

Canadian Ratings (Eng)

Canadian Ratings (Frn)

PG-13:

SEL Select

Move

NC-17:

SEL Return

Move

Use the CURSOR buttons ̆ or ̄ to select the MOVIE RATING category that you want to block.

Press SELECT to block the MOVIE RATING that you have selected. Once rating is selected, for example PG-13, all

movies rated PG-13 and higher (R, NC-17, and X) will be blocked.

Press EXIT to quit the menu or select MOVIE RATING to return to the previous menu.

Motion Picture Ratings Chart

General audiences. All ages admit-

ted.

Parental guidance suggested.

Some material may not be suitable

for children.

Parents strongly cautioned. Some

material may be inappropriate for

children under 13.

PG-13

Restricted. Under 17 requires

accompanying parent or adult

guardian.

No one 17 and under admitted.

NC-17

Adults only

Contains no rating. Not Rated

(NR) and Not Applicable (NA) pro-

grams. Movie has not been rated or

ratings do not apply.

NOT RATED (NR)

NOTES: 1. A movie rating is dependent upon the movie that is viewed. If the movie does not carry a rating, the TV will not block

it.

2. Blocking “NOT RATED (NR)” programs may block emergency programming, sports, news, public service

announcements, religious programs and weather.

3. If a CableCARD is installed, your cable operator may provide an Emergency Alert System (EAS) message in the

event of a local or national emergency with the purpose of alerting the general public. When you receive such

messages, the Projection Television will immediately tune to an EAS channel as directed by the EAS message.

Please be advised that if the EAS channel is blocked using the Locks feature, you will not be able to tune to that

channel.

LOCKS

Use TV RATINGS to prevent the viewing of any TV program that you feel may be inappropriate

due to its content.

TV Ratings

Locks

TV Ratings

Locks

Change Access Code

Sub Category

Engage Lock

Status

TV-Y:

TV Time Lock

Movie Ratings

TV Ratings

TV-Y7:

TV-G:

Canadian Ratings (Eng)

Canadian Ratings (Frn)

TV-PG:

TV-14:

TV-MA:

SEL Select

Move

SEL Return

Move

Use the CURSOR buttons ̆ or ̄ to highlight the category that you want to block.

Press select to block the TV RATINGS that you have selected.

Press EXIT to quit the menu or select TV RATINGS to return to the previous menu.

TV Parental Guide Ratings Chart

NOTES:

None.

N/A

If you Block TV-14D, you will still permit

TV MA programs; If you block TV-14DV,

you will automatically block TV-MAV pro-

grams, but you will still permit TV-MALS

programs. This means that the TV will

block violence in TV-14 and higher (TV-

MA), but not language and sex.

TV program ratings are dependent on

the broadcaster. If the program is not

rated, the TV will not block it.

If a CableCARD is installed, your cable

operator may provide an Emergency

Alert System (EAS) message in the

event of a local or national emergency

with the purpose of alerting the general

public. When you receive such mes-

sages, the Projection Television will

immediately tune to an EAS channel as

directed by the EAS message. Please

be advised that if the EAS channel is

blocked using the Locks feature, you will

not be able to tune to that channel.

All children. The themes and elements in this

program are specifically designed for a very

young audience, including children from ages

2-6.

TV-Y

Directed to older children. Themes and ele-

ments in this program may include mild physi-

cal or comedic violence, or may frighten chil-

dren under the age of 7.

TV-Y7

TV-G

General audience. It contains little or no vio-

lence, no strong language, and little or no sex-

ual dialogue or situations.

Parental guidance suggested. The program

may contain infrequent coarse language, limit-

ed violence, some suggestive sexual dialogue

and situations.

TV-PG

Parents strongly cautioned. This program

may contain sophisticated themes, intense

sexual situation, more intense violence and

intensely suggestive dialogue.

TV-14

Mature audiences only. This program may

contain mature themes, indecent language,

graphic violence, and explicit sexual content.

TV-MA

Fantasy Violence

Violence

Sexual Situation

Adult Language

Sexually Suggestive Dialogue.

LOCKS

Use Canadian Ratings (Eng) to block any type of movie and television program in Canada that

you feel might be inappropriate in its content.

Canadian Ratings

(Eng)

Locks

Canadian Ratings (Eng)

Change Access Code

Status

Engage Lock

TV Time Lock

C8+:

Movie Ratings

TV Ratings

PG:

Canadian Ratings (Eng)

14+:

Canadian Ratings (Frn)

18+:

SEL Select

Move

SEL Return

Move

Use the CURSOR buttons ̆ or ̄ to select the CANADIAN RATINGS (Eng) category that you want to block.

Press SELECT to set the CANADIAN RATINGS (Eng) that you have selected. Once rating is selected, for example C8+,

all movies and television programs rated C8+ and higher (G, PG, 14+ and 18+) will be blocked automatically.

Press EXIT to quit menu.

Canadian Ratings English Chart

Programming intended for children under age 8 - Violence Guidelines; Careful

attention is paid to themes, which could threaten children’s sense of security and well-

being. There will be no realistic scenes of violence. Depictions of aggressive behav-

iour will be infrequent and limited to portrayals that are clearly imaginary, comedic or

unrealistic in nature. Other Content Guidelines: There will be no offensive language,

nudity or sexual content.

Programming generally considered acceptable for children 8 years and over to

watch on their own - Violence Guidelines: Violence will not be portrayed as the pre-

ferred, acceptable, or only way to resolve conflict; or encourage children to imitate dan-

gerous acts which they may see on television. Any realistic depictions of violence will

C8+

be infrequent, discreet, of low intensity and will show the consequences of the acts.

Other Content Guidelines: There will be no profanity, nudity or sexual content.

General Audience - Violence Guidelines: Will contain very little violence, either physi-

cal or verbal or emotional. Will be sensitive to themes which could frighten a younger

child, will not depict realistic scenes of violence which minimize or gloss over the effects

of violent acts. Other Content Guidelines: There may be some inoffensive slang, no

profanity and no nudity.

Parental Guidance - Programming intended for a general audience but which may not

be suitable for younger children. Parents may consider some content inappropriate for

unsupervised viewing by children ages 8-13. Violence Guidelines: Depictions of conflict

and/or aggression will be limited and moderate; may include physical, fantasy, or super-

natural violence. Other Content Guidelines: May contain infrequent mild profanity, or

mildly suggestive language. Could also contain brief scenes of nudity.

Programming contains themes or content which may not be suitable for viewers

under the age of 14 - Parents are strongly cautioned to exercise discretion in permit-

ting viewing by pre-teens and early teens. Violence Guidelines: May contain intense

scenes of violence. Could deal with mature themes and societal issues in a realistic

fashion. Other Content Guidelines: May contain scenes of nudity and/or sexual activity.

There could be frequent use of profanity.

14+

Adult - Violence Guidelines: May contain violence integral to the development of the

plot, character or theme, intended for adult audiences. Other Content Guidelines: May

contain graphic language and explicit portrayals of nudity and/or sex.

18+

LOCKS

Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various pro-

gram ratings that you feel might be inappropriate in its content.

Canadian Ratings

(Frn)

Locks

Canadian Ratings (Frn)

Change Access Code

Status

Engage Lock

TV Time Lock

8 ans+:

Movie Ratings

13 ans+:

TV Ratings

16 ans+:

Canadian Ratings (Eng)

18 ans+:

Canadian Ratings (Frn)

SEL Select

Move

SEL Return

Move

Use the CURSOR buttons ̆ or ̄ to highlight the category that you want to block.

Press SELECT to set the CANADIAN RATINGS (FRN) that you have selected.

Once rating is selected, for example 8 ans+, all movies and television programs rated 8 ans+ and higher will be

automatically blocked.

Press EXIT to quit menu or select the CURSOR buttons ̇ to return to the previous menu.

Canadian Ratings French Chart

General - Programming intended for audiences

of all ages. Contains no violence, or the vio-

lence content is minimal or is depicted appropri-

ately with humor or caricature or in an unrealis-

tic manner.

8 + General - Not recommended for young

children - Programming intended for a broad

audience but contains light or occasional

violence that could disturb young children.

Viewing with an adult is therefore recommended

8 ans +

for young children (under the age of 8) who can-

not differentiate between real and imaginary

portrayals.

Programming may not be suitable for chil-

dren under the age of 13 - Contains either a

few violent scenes or one or more sufficiently

13 ans +

violent scenes to affect them. Viewing with an

adult is therefore strongly recommended for chil-

dren under 13.

Programming is not suitable for children

under the age of 16 - Contains frequent scenes

of violence or intense violence.

16 ans +

Programming restricted to adults - Contains

constant violence or scenes of extreme violence.

18 ans +

TIMERS

Select Timers to set your Clock, Sleep Timer, Event Timer and Day/Night Timer Recordings.

Timers

Video

Set The Clock

Audio

Set Sleep Timer

Set Day/Night Timer

Set Event Timer

Aspect

Chan. Manager

Locks

SEL Return

Move

Timers

Setup

SEL

Move

Sel

The Clock must be adjusted before you can use the “Set Event Timer” or Day/Night Timer” feature.

Set The Clock

Timers

Set The Clock

Set Sleep Timer

Set Day/Night Timer

Set Event Timer

Time Zone:

PST

MST

HST

CST

ATL

EST

AKST

SEL

Move

Select

Daylight Saving Corrections

Time:

Move

2:53 PM Jun 28 2004

SEL Return

Use the CURSOR buttons ̆, ̄, ̇, ̈ to highlight the chosen Time Zone settings.

Press the SELECT button to select.

If you observe daylight savings, use CURSOR PAD to highlight “Daylight Saving Correction” and press the SELECT button to select.

Use the CURSOR buttons ̆, ̄, ̇, ̈ to highlight the current time (hour and minute), AM or PM, Month, Day, and Year.

Use the CURSOR buttons ̆, ̄ to adjust settings.

Press the SELECT button to set the Time and Date.

Press EXIT to quit the menu.

NOTES: When “Daylight Saving Correction” is checked “ꢁ”, the TV will automatically calculate the clock adjustment for

Daylight Saving.

TIMERS

Select this feature to set your Sleep Timer from 30 minutes to 3 hours (30 minute increments).

Set Sleep Timer

Timers

Set The Clock

Set Sleep Timer

Set Day/Night Timer

Set Event Timer

Set Sleep Timer

Set Day/Night Timer

Set Event Timer

0:00

0:30

Move

Set

Move

Set

Press the CURSOR button ̈ repeatedly to set your Timer from 0:00, 0:30, 1:00, 1:30, 2:00, 2:30 and 3:00.

Select this feature to activate and set your TV’s Day/Night Picture Mode automatically.

Set Day/Night Timer

Timers

Set The Clock

Set Sleep Timer

Set Day/Night Timer

Set Event Timer

Set Day/Night Timer

Activate

Day Mode On

Day Mode Off

12:00 AM

SEL

Move

Select

SEL Return

Move

Use the CURSOR buttons and the SELECT button to activate the Day/Night Timer.

Use the CURSOR buttons to select Day Mode On and to set it’s timer.

Use the CURSOR buttons to select Day Mode Off and to set it’s timer.

TIMERS

This function will automatically operate the Projection TV viewing reservation of a program. If the clock is

not set, you can not use this function and the screen below will appear. The message on the screen will dis-

appear after 3 seconds, then the screen automatically goes to the clock setup mode (see page 51).

Set Event Timer

Please Set Clock First.

Timers

Set Event Timer

7:32 PM

Set The Clock

Set Sleep Timer

Set Day/Night Timer

Set Event Timer

Event 1

Event 2

Event 3

Event 4

--:-- AM

--:-- AM Jan 1, 2004

Ant A --------

--:-- AM

--:-- AM Jan 1, 2004

Ant A --------

--:-- AM

--:-- AM Jan 1, 2004

Ant A --------

--:-- AM

--:-- AM Jan 1, 2004

Ant A --------

SEL Return

Move

Timers

7:32 PM

Set Event Timer

Event 1

Event 2

Event 3

Event 4

--:-- AM

Ant A --------

--:-- AM --:-- AM Jan 1, 2004

Ant A --------

--:-- AM Jan 1, 2004

--:-- AM

--:-- AM Jan 1, 2004

Ant A --------

--:-- AM

--:-- AM Jan 1, 2004

Ant A --------

SEL On/Off

Return

Move

Use the CURSOR buttons ̆, ̄ to highlight Event 1, Event 2, Event 3, Event 4 and then press the SELECT button to select.

Use the CURSOR buttons ̈, ̆, ̄ to highlight and select START TIME Hour/Minute.

Use the CURSOR buttons ̈, ̆, ̄ to highlight and select START TIME AM/PM.

Use the CURSOR buttons ̈, ̆, ̄ to highlight and select FINISH TIME Hour/Minute.

Use the CURSOR buttons ̈, ̆, ̄ to highlight and select FINISH TIME AM/PM.

Use the CURSOR button ̈ to highlight the MONTH.

Use the CURSOR button ̆ to select a MONTH or CURSOR button ̄ to select Daily, Weekly - Sunday to Monday. Use the CURSOR

button ̇ to return to MONTH.

Use the CURSOR buttons ̈, ̆, ̄ to highlight and select the DAY of the MONTH.

Use the CURSOR buttons ̈, ̆, ̄ to highlight and select the YEAR.

Use the CURSOR buttons ̈, ̆, ̄ to highlight and select Ant A or Ant B.

Use the CURSOR buttons ̈, ̆, ̄ or NUMBER buttons to set the channel the TV will tune into.

A “ꢁ“ in the box means it is enabled.

NOTE:

1. When the INFO button is pressed, the Event Timer Icon will only display the current date ON/OFF timer.

2. The Off Timer will only activate if the TV was turned on by the On Timer and no channel selection was

made after this time. If you change the channel after the On Timer has been activated, the Off Timer will deactivate.

3. If no remote control button is pressed after viewing reservation is activated, the TV will automatically turn off after three

hours. Therefore, do not Set Event Timer for more than three hours if you do not plan to control your television with

the remote control.

CAUTION: Do not use your TV as a deterrent when away from home by using the On and Off Timers. For safety, the TV

should be turned off when you are away from home.

SETUP

Select SETUP when setting your TV up for the first time. Use the CURSOR buttons ̆ or ̄ on the remote to highlight

the function desired.

Setup

Video

Setup

Magic Focus Tune Up

Audio

Menu Preference

Set The Inputs

Aspect

Chan. Manager

Locks

Set Virtual HD

Set Black Side Panel

Set Closed Captions

Set Monitor Out

About Your TV

Timers

Setup

SEL

Move

Sel

SEL Return

Move

Setup

Magic Focus Tune Up

Menu Preference

Set The Inputs

CableCARD Info

Set AV Control

Upgrades

Set Virtual HD

Quick Start Up

Set Black Side Panel

Set Closed Captions

Set Monitor Out

About Your TV

SEL Select

Move

SEL Select

Move

Use the CURSOR buttons ̆, ̄, ̇, ̈ to highlight the sub-menu of your choice.

Press the SELECT button to select.

SETUP

Magic Focus

Tune Up

Auto Digital Convergence Adjustment

Please turn ON your television for at least 20 minutes before using this feature.

The Magic Focus button on control panel will not work when adjustment mode is set to Manual (see page 56 or 57).

Your HITACHI Projection TV has three color projection tubes: one for red, one for green, one for blue. When mixed together in the proper

proportion, the output of these three color tubes can produce any color. To produce these colors, however, the beams must be precisely

aligned over each other so that the colors can be mixed. The process of aligning these picture beams is called “convergence”.

Over a period of time, the picture tubes can drift out of alignment due to normal bumps and vibrations or moving the TV. If you move

your TV, or if, after a time, you notice color rings or halos around objects in the picture, you may want to converge (align) the colors.

Properly converged, the lines appear white, which is actually a combination of the outputs of the three color tubes. The output of the

green tube is stationary. The outputs of the red and blue tubes can be adjusted. When properly aligned, the outputs of all three tubes

should be directly over each other to produce the white lines.

To simplify convergence, HITACHI incorporates a function called MAGIC FOCUS located on the front control panel, which allows the TV

to self-adjust. Press this MAGIC FOCUS button and the convergence self adjustment will start and this process will take approximately

20 seconds. If this button is pressed during this process, no change in picture quality will occur. After this 20 second self-adjust period,

picture quality will be optimum (do not move the TV during self-adjust).

You may also select MAGIC FOCUS TUNE UP from the Setup Menu.

MAGIC FOCUS

MAGIC

FOCUS

NOTE:

Only a momentary press of the MAGIC FOCUS button is necessary to start AUTO DIGITAL CONVERGENCE. At any

time during this convergence correction process, you may press the MAGIC FOCUS button to exit the MAGIC FOCUS

mode. However, the convergence correction process needs to be completed to SAVE the new corrected convergence

data.

Video

Setup

Magic Focus Tune Up

Audio

Menu Preference

Set The Inputs

Aspect

Chan. Manager

Locks

Set Virtual HD

Set Black Side Panel

Set Closed Captions

Set Monitor Out

About Your TV

Timers

Setup

SEL

Move

Sel

SEL Select

Move

Setup

Magic Focus Tune Up

Aligns the Red, Green, and Blue

colors to correct for Magnetic

Influences.

Adjustment Mode

Auto

MAGIC FOCUS

At turn off,

(After 90 days).

9 Point Manual

117 Point Manual

If you want to adjust now

Start

SEL Return

Move

NOTE:

When Auto Start “At turn off” is selected, the TV will adjust itself after 90 days.

SETUP

Manual Convergence Adjustment Mode (9 Point Manual Adjustment)

NOTES: 1. Please turn ON your television for at least 20 minutes before using this feature.

2. Auto Adjustment Mode is recommended. If convergence is still not acceptable, use the Manual Adjustment Mode.

3. If Auto Adjust mode is selected or the Magic Focus button is pressed, all manual adjust mode settings will be erased.

Using the Remote Control, select SETUP-MAGIC FOCUS TUNE UP-MANUAL ADJUSTMENT MODE-9 POINT MANUAL-START to

access convergence 9 point pattern. The adjustment point is indicated by the Adjustment Point Cursor.

To Move Adjustment Point

To move the adjustment point cursor using the CURSOR buttons, the Adjustment Cursor must be WHITE. Another way to move the

Adjustment Point Cursor is to press the following buttons: [2] up, [4] left, [5] down, [6] right. If you use the number buttons while the

adjustment point is WHITE, it will change to RED.

To Change the Color of Adjustment Point

Press the SELECT button repeatedly (WHITE-RED-BLUE-WHITE...). Green color is fixed and cannot be adjusted.

To Adjust the Convergence

Move the Adjustment Cursor to the point to be adjusted. Use the CURSOR buttons to match the RED and BLUE colors to GREEN

(reference color). Properly aligned, all three colors should appear white.

Video

Setup

Magic Focus Tune Up

Audio

Menu Preference

Set The Inputs

Aspect

Chan. Manager

Locks

Set Virtual HD

Set Black Side Panel

Set Closed Captions

Set Monitor Out

About Your TV

Timers

Setup

SEL Sel

Move

SEL Select

Move

Adjustment Point

Cursor

Setup

Magic Focus Tune Up

Aligns the Red, Green, and Blue

colors to correct for Magnetic

Influences.

Adjustment Mode

Auto

At turn off,

(After 90 days).

9 Point Manual

117 Point Manual

If you want to adjust now

Start

SEL Return

Move

If convergence is acceptable after Manual Convergence adjustment, press EXIT button to access menu mode.

Setup

Magic Focus Tune Up

Manual Adjust

Please make a selection from

the options below

Cancel

EXIT

Done

Back

Reset

SEL Select

Move

Use the CURSOR buttons to highlight your chosen option. Press the SELECT button to select.

Select CANCEL to cancel adjusted data and return to main picture.

Select DONE to save your adjustments and return to main picture.

Select BACK to return to the manual convergence adjustment mode.

Select RESET to recall the factory pre-set convergence data.

SETUP

Manual Convergence Adjustment Mode (117 Point Manual Adjustment)

NOTES: 1. Please turn ON your television for at least 20 minutes before using this feature.

2. Auto Adjustment Mode is recommended. If convergence is still not acceptable, use the Manual Adjustment Mode.

3. If Auto Adjust mode is selected or the Magic Focus button is pressed, all manual adjust mode settings will be erased.

Using the Remote Control, select SETUP-MAGIC FOCUS TUNE UP-MANUAL ADJUSTMENT MODE-117 POINT MANUAL-START to

access convergence 117 point pattern. The adjustment point is indicated by the Adjustment Point Cursor.

To Move Adjustment Point

To move the adjustment point cursor using the CURSOR buttons, the Adjustment Cursor must be WHITE. Another way to move the

Adjustment Point Cursor is to press the following buttons: [2] up, [4] left, [5] down, [6] right. If you use the number buttons while the

adjustment point is WHITE, it will change to RED.

To Change the Color of Adjustment Point

Press the SELECT button repeatedly (WHITE-RED-BLUE-WHITE...). Green color is fixed and cannot be adjusted.

To Adjust the Convergence

Move the Adjustment Cursor to the point to be adjusted. Use the CURSOR buttons to match the RED and BLUE colors to GREEN

(reference color). Properly aligned, all three colors should appear white.

Video

Setup

Magic Focus Tune Up

Audio

Menu Preference

Set The Inputs

Aspect

Chan. Manager

Locks

Set Virtual HD

Set Black Side Panel

Set Closed Captions

Set Monitor Out

About Your TV

Timers

Setup

SEL Sel

Move

SEL Select

Move

Adjustment Point

Cursor

Setup

Magic Focus Tune Up

Aligns the Red, Green, and Blue

colors to correct for Magnetic

Influences.

Adjustment Mode

Auto

At turn off,

(After 90 days).

9 Point Manual

117 Point Manual

If you want to adjust now

Start

SEL Return

Move

If convergence is acceptable after Manual Convergence adjustment, press EXIT button to access menu mode.

Setup

Magic Focus Tune Up

Manual Adjust

Please make a selection from

the options below

Cancel

EXIT

Done

Back

Reset

SEL Select

Move

Use the CURSOR buttons to highlight your chosen option. Press the SELECT button to select.

Select CANCEL to cancel adjusted data and return to main picture.

Select DONE to save your adjustments and return to the main picture.

Select BACK to return to the manual convergence adjustment mode.

Select RESET to recall the factory pre-set convergence data.

SETUP

Menu Preference

This feature will allow you to select any one of three different languages for all on-screen displays.

Setup

Menu Preference

Magic Focus Tune Up

Menu Preference

Set The Inputs

Set The Language

English

Francais

Español

Set The Menu Background

Shaded

Set Virtual HD

Solid

Set Black Side Panel

Set Closed Captions

Set Monitor Out

About Your TV

SEL Return

Move

SEL Select

Move

Setup

Menu Preference

Set The Language

English

Francais

Español

Set The Menu Background

Shaded

Solid

SEL Select

Move

Use the CURSOR buttons ̇ , ̈ to highlight the language of your choice.

Press SELECT to select the highlighted language.

Press EXIT to quit menu or select MENU PREFERENCE to return to previous menu.

SETUP

This function allows you to choose from two menu backgrounds.

Menu Background

Setup

Menu Preference

Set The Language

English

French

Spanish

Set The Menu Background

Shaded

Move

Solid

SEL Select

Use the CURSOR buttoms ̇ , ̈ to highlight SET THE MENU BACKGROUND (shaded or solid), and press the SELECT button to select

setting.

Press EXIT to quit menu or the CURSOR buttons ̇ to return to previous menu.

Select SOLID for a black background (no picture can be seen behind menu screen), or select SHADED for a light background.

Use this feature to give a name to any of the five video inputs.

Set The Inputs

Setup

Set The Inputs

Rename List

Setup

Magic Focus Tune Up

Menu Preference

Set The Inputs

Set Virtual HD

Set Black Side Panel

Set Closed Captions

Set Monitor Out

About Your TV

AVR

DVD

DVD2

DVD3

PVR

PVR2

SAT

STB

STB2

VCR

Video1

Video2

Video3

Video4

Video5

CAM

CBL

VCR2

VCR3

CBL2

Reset

SEL Select

Move

SEL Return

Move

Press the CURSOR buttons ̆, ̄, ̇, ̈, to highlight the name of the video inputs.

Press the SELECT button to select desired input name.

Select RESET to set video names to original factory preset condition.

SETUP

Use this function to automatically turn the TV on and tune to Video2 when it detects a video signal to

input 2.

Video 2 Auto Link

Setup

Set The Inputs

Rename List

Setup

Set The Inputs

Rename List

Video1

Video2

Video3

Video4

Video5

AVR

DVD

DVD2

DVD3

PVR

PVR2

SAT

STB

STB2

VCR

AVR

DVD

DVD2

DVD3

PVR

PVR2

SAT

STB

STB2

VCR

Video1

Video2

Video3

Video4

Video5

CAM

CBL

CAM

VCR2

VCR3

CBL

VCR2

VCR3

CBL2

Reset

Auto Link

Auto

Remote

Off

SEL Return

Move

SEL Return

Move

Use the CURSOR buttons ̇, ̈, ̆ or ̄, then press the SELECT button to change AUTO LINK setting.

When AUTO is selected, the TV will turn on and tune to Video2 automatically, when the Video2 input device is turned on. This is con-

venient when you want to watch a movie with your VCR, laserdisc player, or DVD player.

When REMOTE is selected, the TV will turn on and switch to Video2 automatically when the Video2 input device is turned on and the

VCR, laserdisc, or DVD play button on your remote control is pressed.

This is convenient when you want to record a movie with your VCR and watch it later.

Select Off to disable this function.

Press EXIT to quit menu.

NOTES: 1. Once the TV has been turned on using the AUTO LINK feature, it must be reset before AUTO LINK is used again. To

do this, turn your VCR, laserdisc, or DVD player OFF. This feature is now reset and will turn on your TV as described

above.

2. When using REMOTE mode, any remote control button will substitute for your video input device play button. However,

intended operation is for use with your VCR, laserdisc, or DVD play button.

3. If no remote control button is pressed after the TV is turned on by AUTO LINK, the TV will automatically turn off after

three hours.

SETUP

Set Virtual HD

Use this feature to select between 1080i and 540p.

NOTE:

Set Virtual HD is not available (grayed out) in Digital Channels and 1080i input.

The BLACK SIDE PANEL function turns the gray side bars on/off when watching 4:3 signals in

Standard mode. The top/bottom gray bar will appear in SPLIT MODE PIP and SPLIT FREEZE. The

TV set will always return to “Set Black Side Panel - OFF” setting every time the TV is powered “OFF”.

Set Black Side

Panel

NOTE:

To maximize operating life of the TV’s picture tubes when watching 4:3 signal, Black Side Panel is cancelled at Power

OFF. It is recommended to watch 4:3 signal with gray side bar.

SETUP

Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video

Set Closed Caption

which are displayed on the TV screen. Your local TV program guide denotes these programs as

Setup

Set Closed Captions

Magic Focus Tune Up

Caption Display

Off

Menu Preference

Set The Inputs

Auto

Text

Set Virtual HD

Analog Captions

Mode:

Channel:

Captions

Set Black Side Panel

Set Closed Captions

Set Monitor Out

About Your TV

Digital Captions

SET

SEL Select

Move

SEL Return

Move

Caption Display: On/Off will turn the

display on or off.

Auto will turn the

display on when Mute/Soft Mute is on.

Caption Mode: Captions is for the program you are viewing.

Text is for additional information such as news reports or a TV program guide. This information covers the entire

screen and viewing the TV program is not possible. Text may not be available with every

program.

CHANNEL:

1 is used for the primary language (usually English).

2 is sometimes used for a second language (may vary by region).

3 is sometimes used for a third language (may vary by region).

4 is sometimes used for a fourth language (may vary by region).

Use the CURSOR buttons ̆, ̄, ̇, ̈ to highlight the function to change then press the SELECT button to select the function.

Press EXIT to quit menu or the CURSOR button ̇ to return to previous menu.

Digital Captions: Set captions for digital programs. This function will help choose and set available language, font, size and style

of digital captions.

Digital Caption Font Style

Service: [1 2 3 4 5 6]

Setup

Set Closed Captions

Caption Display

Off On

Language: [Unknown

]

: [Default 1 2 3 4 5 6 7 8]

Auto

Text

Font

Size

Style

Standard

Small Large

High Visibility

Analog Captions

Mode:

Channel:

Captions

[HITACHI]

Digital Captions

SET

SEL Return

Move

SEL Return

Move

Use the CURSOR buttons ̆, ̄, ̇, ̈ to highlight desired Digital Captions feature.

Press the SELECT button to select desired feature.

Press EXIT to quit menu or the CURSOR button ̇ to return to previous menu.

NOTES: 1. Some types of digital closed captions will not work with this TV.

2. CAPTION DISPLAY will not work when viewing a 480p, 720p, or 1080i input via the COMPONENT:Y-P P inputs.

B R

3. When PIP Surf is on, Closed Caption will not work.

4. Digital Captions Font Style are sometimes different from the Font Style of Analog Captions.

5. Closed Caption and Digital Captions availability and content depends on the broadcaster. Closed Caption is

available when Closed Caption icon is displayed on screen.

6. Digital Captions will not be available (grayed out) when using analog channels.

SETUP

This feature will select the source of the Monitor Output.

Set Monitor Out

Setup

Set Monitor Out

Setup

Magic Focus Tune Up

Video Out

Monitor

Menu Preference

Set The Inputs

TV Tuner Out

Set Virtual HD

Set Black Side Panel

Set Closed Captions

Set Monitor Out

About Your TV

Audio Out

Fixed

Variable

SEL Select

Move

SEL Return

Move

Monitor- Select Monitor to output the audio and video signals of the chosen input source (ANT A, ANT B, VID3-VID5) to a VCR or other

A/V device.

TV Tuner Out- Select TV Tuner Out to output the audio and video signals of the last watched Antenna Source (ANT A, ANT B).

Fixed- Select Audio Out Fixed to have the Audio at fixed volume.

Variable- Select Audio Out Variable to have Audio settings that can be controlled.

Use CURSOR buttons ̆, ̄ to highlight the function to change then press the SELECT button to select the function.

Press EXIT to quit menu or CURSOR button ̇ to return to previous menu.

NOTE:

When TV Tuner Out is selected, Variable Audio Out will not be available (grayed out).

The TV model name and dimensions will be displayed on the TV screen. The dimensions of each TV model

are listed on page 68.

About Your TV

Setup

About Your TV

Setup

Magic Focus Tune Up

Menu Preference

Set The Inputs

Model:

Dimensions (Inches) (mm)

Set Virtual HD

Height:

Width:

Depth:

- / -

Set Black Side Panel

Set Closed Captions

Set Monitor Out

About Your TV

Caution

SEL Select

Move

SEL Return

Move

Setup

About Your TV

Caution:

Continuous on-screen

displays such as Video games, stock

market quotations, and other

fixed (non-moving) patterns can

cause permanent damage.

Such “SCREEN BURNS” are not covered

by your Hitachi Factory Warranty.

SEL Return

Move

Select this feature to access your CableCARD ID and HOST ID. Please have this information ready when

you call your cable operator (see also page 11).

CableCARD Info

Setup

CableCARD Info

Set AV Control

Upgrades

Select the button below to access

your CableCARD ID and Host ID.

Set Stand-By Mode

SEL Select

Move

CableCARD Info

SEL Select

Move

SETUP

This feature will select the AV Control feature. Set this feature if you want to control some of the TV functions

from an external home control system.

Set AV Control

Setup

Set AV Control

CableCARD Info

Set AV Control

Upgrades

If you want to use the AV Control

function, please set the RS232C.

Quick Start Up

SEL Select

Move

Connected RS232C

SEL Return

Move

Use the CURSOR buttons and the SELECT button to check the Connected RS232C box.

NOTE:

For use with third party home Audio/Video control systems which are commercially available. Please see your dealer

regarding these “non Hitachi” home control systems.

It shows software information and easy upgrade procedure. This function allows the TV software to be

Upgrades

upgraded by using a flash card (MMC Card). If a future software upgrade is required for your TV, Hitachi will

notify and provide you with a flash card. In order to receive written notification and the flash card, please com-

plete and return the warranty card.

Setup

CableCARD Info

Set AV Control

Setup

Upgrades

Software Version #: Main

VXX.XX

Upgrades

Quick Start Up

MMC Software Upgrade

Upgrade Now

SEL Select

Move

Please insert MMC card

before upgrading.

SEL Return

Move

Insert MMC card, then press the CURSOR buttons ̆, ̄ to highlight “Upgrade Now”. Press the SELECT button to select and start

upgrading.

NOTE:

Any power interruption during the upgrade process will cancel the upgrade. When this happens, repeat the upgrade

procedure.

This feature will select Quick Start Up options. Set this feature to ON to have the TV tune channels (both

Quick Start Up

Analog and Digital) quickly when first turning the TV on. Set this feature to OFF to save electricity. Selecting

ON for the Quick Start Up feature will activate the TV tuners circuits when the TV is in “standby mode” which

is commonly referred to as “off”. This will allow you to quickly tune to channels when first turning the TV on.

Digital signals often change and this feature will monitor any changes and prepare the television to quickly

present a picture. A small amount of electricity is used to continually monitor signals when this feature is

selected.

Setup

CableCARD Info

Quick Start Up

Set AV Control

Upgrades

Select ON to have the TV tune

channels quickly at 1st turn on.

Quick Start Up

SEL Select

Move

Select OFF to save electricity.

Off

SEL Return

Move

NOTE:

At initial TV Turn “ON”, the Power button LED will blink several times before a channel can be tuned and viewed. This is

a normal default operation of this television. The blinking time of the Power button LED varies depending on the period

of time between when you turn “ON” and when you turn “OFF” the TV. This default operation is an energy saving feature.

You can choose not to use this feature by selecting “On” for the “Quick Start Up” option in the On-Screen-Display Menu.

Select “Setup” in the On-Screen-Display Menu, then select “Quick Start Up”. Select the “On” feature to quickly tune and

view channels at initial TV Turn “ON.”

CARE OF YOUR HITACHI TELEVISION

AND YOUR REMOTE CONTROL

Dust the screen and cabinet with a soft cloth.

Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if

the screen is extremely dirty.

Place your Television away from extreme heat, humidity, and extremely dusty places.

Remove the plug from the wall outlet if your Television will not be used for a long period of time, for instances,

when you go on vacation.

DO NOT

Do not clean your screen or cabinet with strong cleaners, polishes or a chemically treated cloth.

Do not place rubber or vinyl products or cellophane tape on your Television.

Do not touch the screen too often.

Do not subject the remote control to shocks such as dropping it on the floor, etc. Physical damage to the precision

parts may result.

Avoid placing the remote control or the Simple Remote Control in a high humidity place or getting it wet. Do not leave

it on or near a heater. Excessive heat or moisture may cause the unit to cease operation.

When the batteries run down, remote control operation will become erratic or possibly stop altogether. Replace the

old batteries with two new “AA” size batteries as soon as possible to preserve the remote control precodes that were

set for the devices. Pressing a remote control button with a “DEAD” battery might erase all precodes in memory. Do

not use an old battery with a new battery.

Exposure of the viewing screen to prolonged direct sunlight or heat may cause the screen to permanently warp,

resulting in a distorted picture.

RECEPTION PROBLEMS

• IGNITION NOISE:

Black spots or horizontal streaks may appear, picture may flutter or drift.

Usually caused by interference from automobile ignition systems, neon

lamps, electrical drills, and other electrical appliances.

• GHOSTS:

Ghosts are caused by the television signal following two paths. One is the

direct path and the other is reflected from tall buildings, hills or some other

objects. Changing the direction or position of the antenna may improve

reception. Ghosting may also be caused by defects in the antenna system

such as unshielded leads or connecting several sets to the same antenna

without using multiple antenna couplers.

• SNOW:

If your receiver is located in the fringe area of a television station where the

signal is weak, your picture may be marred by the appearance of small

dots. When the signal is extremely weak, it may be necessary to install a

special antenna to improve the picture.

• RADIO FREQUENCY INTERFERENCE:

The interference produces moving ripples or diagonal streaks, and in some

cases, causes loss of contrast in the picture.

• BLOCK NOISE (Digital Input):

Fuzzy blocks may appear in some area or the whole area of the screen.

This is usually caused by interference from automobile ignition systems,

neon lamps, electrical drills, ghosting of the image and weak signals.

• BLACK SCREEN:

When using an antenna, weak signals will display a black screen. It may

be necessary to upgrade your antenna.

NOTE:

The TV set can generate sound distortion in external devices such as a radio. Please separate radio equipment

from the TV set to a considerable distance.

USEFUL INFO

SYMPTOMS

No Picture, no sound

Sound OK, picture poor

Picture OK, sound poor

Picture blurred

Lines or streaks in picture

Poor reception on some channels

Picture rolls vertically

No color

Poor color

HITACHI Projection Television incorporates advanced power surge protection technology designed to protect against

component or circuit damage due to external or internal voltage power surges.

IF YOUR TELEVISION SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE:

1. Press the power switch (ON/OFF switch) once.

2. If there is still no power, wait 30 seconds and press the power switch again.

3. If there is still no power, unplug the power cord from the wall. Wait 30 seconds and plug the power cord back in.

Press the power switch again.

This protective technology should provide for years of lasting entertainment from your HITACHI Projection Television.

USEFUL INFO

Features:

•

Superfine Picture Quality

1280 Line Horizontal Resolution

•

Remote (Controls many PVR/VCR brands, cable boxes, satellite boxes, and other audio equipment).

New Easy-to-Use (3-Language) On-Screen Menu

Full Set of Input Jacks, including S-VIDEO

COMPONENT VIDEO:Y-P_B/P_R

Velocity Modulation

Six Aspect Modes

Closed Caption Decoder

2-Tuner Picture in Picture

Magic Focus (Auto Digital Convergence and 9-point/117-point Manual Adjustment)

2 Antenna Inputs (Either for Analog/Digital)

Video Input Sensor

HDMI (High Definition Multimedia Interface) (High Bandwidth Digital Content Protection V1.1 compatible).

Digital Audio Output (Dolby^®Digital and PCM)

3 Dimensional Y/C Comb Filter

Compatible with 1080i, 720p, 480p and 480i input signals.

CableCARD^TMcompatible - Contact your local cable operator for more information.

Technology.

*Licensed by BBE Sound, Inc. under USP5510752 and 5736897. BBE and BBE symbol are registered

trademarks of BBE Sound, Inc. Manufactured under license from BBE Sound, Inc.

•

Technology.

*SRS and

symbol are trademarks of SRS Labs, Inc. SRS technology is incorporated under license from SRS Labs, Inc.

Technology.

*Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby

Laboratories.

•

Technology

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Inputs:

Outputs:

•

Power Input . . . . . . . . . . . . . .AC 120V, 60Hz

•

Video . . . . . . . . . . . . . . . . . . . . . . .1.0Vp-p. 75 Ohm

Audio (Fixed) . . . . . . . . . . . . . .470mVrms, 1k Ohm

S-Video

Luminance (Y) . . . . . . . . . . .1.0Vp-p, 75 Ohm

Chrominance (C) . . . . . . .0.286Vp-p, 75 Ohm

•

Stand-by Power . . . . . . . . . . . . . . . . . . .0.4W

Power Consumption

- Refer to rear panel at the back of the T.V.

Antenna input impedance . . . . . . . . .75 Ohm

Channel coverage

•

Optical Out (Digital Audio) . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .1 optical connector

VHF-Band . . . . . . . . . . . . . . . . . . . . . .2 ~ 13

UHF-Band . . . . . . . . . . . . . . . . . . . . .14 ~ 69

CATV Band . . . . . . . . . . . . . . . . . . . . .1-135

. . . . . . . . . . . . . . . . . . . . . . . . . . . .A-I

Dimensions:

51F710

57F710

65F710

•

Video . . . . . . . . . . . . .1.0Vp-p, 75 Ohm

51F710S

57F710S

65F710S

•

S-Video

Luminance (Y) . . . . . . . . . . .1.0Vp-p, 75 Ohm

Chrominance (C) . . . . . . .0.286Vp-p, 75 Ohm

•

Height (in.)

(mm)

50 3/8

54 9/16

1,385.6

59 15/16

1,521.0

1,279.0

Width (in.)

(mm)

48 3/4

1,239.0

1,372.0

1,549.0

Component Video

Luminance (Y) . . . . . . . . . . . . . . .1.0Vp-p, 75 Ohm

Chrominance (P /P ) . . . . . . . . .0.7Vp-p, 75 Ohm

Depth (in.)

(mm)

21 7/8

557

23 5/8

599.4

25 3/8

644

Audio input Impedance . . . . . . . . . .47k Ohm

Weight (lbs.)

187.4

205

309

•

Average input level . . . . . . . . . . . . . . . . .470mVrms

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . .HDMI 19 PIN

NOTE:

Due to improvements, specifications in this oper-

ating guide are subject to change without notice.

USEFUL INFO

To locate an authorized

HITACHI service facility

in the continental U.S.A.

and Canada,

DIAL TOLL FREE

7 days a week, 24 hours a day

(1-800-448-2244)

Hitachi America, LTD.

Home Electronics Division

Hitachi has made every effort to assure you hours of trouble free operation from your unit. However, should you require service,

a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico. Each facility will provide

you with convenient and expedient assistance. Our service hotline operator will direct you to the Hitachi Authorized Service Facility

nearest you. Just present proof of purchase and/or delivery receipts to the Hitachi Authorized Service Facility, and service will be

rendered in accordance with the terms of the limited warranty as stated on your warranty card or operating guide.

Should you have any questions regarding warranty, service, operation, or technical assistance, please contact:

Hitachi America, LTD.

Home Electronics Division

900 Hitachi Way

Chula Vista, CA 91914-3556

USEFUL INFO

Hitachi Canada, LTD.

Digital Media Division

Should you have any questions regarding warranty, service, operation, or technical assistance, please

contact:

In Canada:

1-800-HITACHI

(1-800-448-2244)

Monday - Friday EST 9:00am - 7:00pm

Saturday EST 9:00am - 5:00pm

Look for your French Manual on the outside of the box.

If the manual is missing, call

1-800-HITACHI

(1-800-448-2244)

for a copy.

Pour de plus amples renseignements sur le service durant la période couverte par la garantie, sur le fonction-

nement ou pour de l’assistance technique communiquez avec:

Au Canada:

1-800-HITACHI

(1-800-448-2244)

Lundi - Vendredi L’EST 9:00am - 7:00pm

Samedi L’EST 9:00am - 5:00pm

La version français de votre manual se trouve a l’exterieur de la boîte.

Si le manuel est manquant, coposez le

1-800-HITACHI

(1-800-448-2244)

pour obenir votre copie.

HITACHI CANADA, LTD.

2495 Meadowpine Blvd.

Mississauga, Ontario L5N 6C3

57” DISASSEMBLY/ASSEMBLY INSTRUCTIONS

(a) Do not attempt to perform this work by yourself.

(b) Request an installation specialist to install this unit.

IMPORTANT POINTS:

sumer installation and handling. Be advised that improper consumer installation/han-

dling is not covered by manufacturer’s warranty.

(d) This Projection Television weighs 205 pounds and has many sensitive components.

CAUTION: DISCONNECT UNIT FROM POWER SOURCE BEFORE DISASSEMBLY / ASSEMBLY

1 - SEPARATION PROCEDURE (Note: read all instructions and understand how to properly and

safely disassemble and assemble unit)

STEP 1

Before disassembling this projection TV set, you must first remove the speaker grille by grabbing the sides and pulling left and right side see

(a)(b). Remove the front decoration panels by unscrewing the 2 screws from each panel, see (c), then remove from the original position,

see (d)(e).

(a)

(b)

(c)

(e)

(d)

Please remove 3 screws

Remove 4 screws (ቢ,ባ,ቤ,ብ) that hold the screen frame

to the cabinet on the Right side, see (a) and (b). Repeat to

remove 4 screws on the Left side.

(ቢ,ባ,ቤ) below screen

frame that hold the back

cover to the cabinet as the

arrows shows, see (b).

(ቢ,ባ,ቤ) below screen

frame that hold the back

cover to the cabinet as the

arrows shows, see (a).

STEP 2

STEP 3

(b) Right Side

(a) Left Side

ብ

(a)

(b)

ብ ቤ

ባ

ቢ

ቤ ባ

ቢ

ባ ቤ

Remove the sensor box by unscrewing the 2 screws located on both sides of the sensor box, see (a). Rotate the sensor box and there are 4 low

voltage connectors located on the sensor board, see (b). Disconnect the connector with the brown wires (PDSE), see (c) and (d). (Make sure to

push the center lock on the connector at the unplug time.)

STEP 4

(a)

(b)

57” DISASSEMBLY/ASSEMBLY INSTRUCTIONS

1 - SEPARATION PROCEDURE CONTINUED

Cont.

STEP 4

(c)

(d)

Remove the joint connector bolts from each side of the back cover using the allen wrench that is provided inside of the instruction bag, see (a) and

(b).

STEP 5

(a)

(b)

Remove from the back side of the TV set only the top 4 screws of the lower rear cover, see (b), as shown by the arrows on the rear cabinet label,

see (a). Do not remove the rear cover board. Remove the (4) four side screws that hold the back cover to the cabinet, see (c) as shown on the label

(a). Total of 8 screws will be removed.

STEP 6

(a)

(b)

(c)

Caution: When the TV is separated, the top portion weights 45 lbs. This task should be done by two persons when separating this TV.

This assembly contains fragile parts, such as glass and the viewing screen. Avoid any type of impact that could cause breakage of these compo-

nents. Remove top portion by grabbing the bottom corner of frame and the back cover, see (a)(b). Lift upwards, see (c)(d), gently place the top por-

tion on the the floor, see (e).

STEP 7

(a)

(c)

(b)

(d)

(e)

57” DISASSEMBLY/ASSEMBLY INSTRUCTIONS

2 - RE-ASSEMBLY PROCEDURE

To re-assemble the set, lift the top portion and align onto the

bottom cabinet. Gently lower the top portion until it sits flush

on the bottom.

Re-install the joint connector bolts (4 pcs.) that were removed

in step 5 of the disassembly.

STEP 8

STEP 9

Re-install the top (4) four screws into the lower rear cover, see (a). Re-install the (4) four side screws that hold the back cover to the cabinet, see

(b).

STEP 10

(a)

(b)

Re-connect the sensor connector to the sensor board, see (a). Re-install the sensor box, see (b).

STEP 11

(a)

(b)

Please re-install 3 screws

Re-install 4 screws (ቢ,ባ,ቤ,ብ) that hold the screen frame

to the cabinet on the Right side, see (a) and (b). Repeat to

re-install 4 screws on the Left side.

(ቢ,ባ,ቤ) below screen

frame that hold the back

cover to the cabinet as the

arrows shows.

(ቢ,ባ,ቤ) below screen

frame that hold the back

cover to the cabinet as

the arrows shows.

STEP 12

STEP 13

(b) Right Side

(a) Left Side

ብ

(a)

(b)

ብ ቤ

ባ

ቢ

ቤ ባ

ቢ

ባ ቤ

Re-install both of the front decoration panels, see (a) and (b). Re-install the speaker grille, aligning it with the bottom cabinet, see (c). This com-

pletes the Disassembly and Assembly instructions.

STEP 14

(a)

(c)

(b)

65” DISASSEMBLY/ASSEMBLY INSTRUCTIONS

(a) Do not attempt to perform this work by yourself.

(b) Request an installation specialist to install this unit.

IMPORTANT POINTS:

sumer installation and handling. Be advised that improper consumer installation/han-

dling is not covered by manufacturer’s warranty.

(d) This Projection Television weighs 309 pounds and has many sensitive components.

CAUTION: DISCONNECT UNIT FROM POWER SOURCE BEFORE DISASSEMBLY / ASSEMBLY

1 - SEPARATION PROCEDURE (Note: read all instructions and understand how to properly and

safely disassemble and assemble unit)

STEP 1

Before disassembling this projection TV set, you must first remove the speaker grille by grabbing the sides and pulling left and right side

see (a)(b). Remove the front decoration panels by unscrewing the 2 screws from each panel, see (c), then remove from the original posi-

tion, see (d)(e).

(a)

(b)

(c)

(e)

(d)

Remove the 8 screws that hold the screen frame to the cabinet on the front side. DO NOT remove the right and left edge screen frame screws (c).

STEP 2

(c)

(b)

(a)

Remove the sensor box by unscrewing the 2 screws located on both sides of the sensor box, see (a). Rotate the sensor box and there are 4 low

voltage connectors located on the sensor board, see (b). Disconnect wires (PDSE), see (c) and (d). (Make sure to push the center lock on the con-

nector at the unplug time.)

STEP 3

(a)

(b)

65” DISASSEMBLY/ASSEMBLY INSTRUCTIONS

1 - SEPARATION PROCEDURE CONTINUED

Cont.

STEP 3

(c)

(d)

Remove the joint connector bolts from each side of the TV set using the allen wrench that is provided inside of the instruction bag, see (a) and (b).

STEP 4

(a)

(b)

Remove from the back side of the TV set only the top 4 screws of the lower rear cover, see (b), as shown by the arrows on the rear cabinet label,

see (a). Do not remove the rear cover board.

STEP 5

(a)

(b)

Caution: When the TV is separated, the top portion weighs 112 lbs. This task should be done by two persons to carry top portion when separating this TV.

This assembly contains fragile parts, such as glass and the viewing screen. Avoid any type of impact that could cause breakage of these components.

Remove top portion by grabbing the bottom corner of frame and the side of the TV, see (a)(b). Lift upwards, see (c)(d), gently place the top portion

on the the floor, see (e).

STEP 6

(a)

(b)

(c)

(d)

(e)

65” DISASSEMBLY/ASSEMBLY INSTRUCTIONS

2 - RE-ASSEMBLY PROCEDURE

To re-assemble the set, lift the top portion and align onto the

bottom cabinet. Gently lower the top portion until it sits flush

on the bottom.

Re-install the joint connector bolts (4 pcs.) that were removed

in step 4 of the disassembly.

STEP 7

STEP 8

Re-install the top (4) four screws into the lower rear cover, see (a).

STEP 9

(a)

Re-connect the sensor connector to the sensor board, see (a). Re-install the sensor box, see (b).

STEP 10

(a)

(b)

Re-install the 8 screws that hold the frame to the cabinet on the front side of the TV.

STEP 11

Re-install both of the front decoration panels, see (a) and (b) Re-install the speaker grille, aligning it with the bottom cabinet, see (c). This com-

pletes the Disassembly and Assembly instructions.

STEP 12

(a)

(c)

(b)

INDEX

Language

Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Locks

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Antennas (Connecting) . . . . . . . . . . . . . . . . . . . . . . . . .5,6

Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22,43

Audio

Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Dolby Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

DRC (Dynamic Range Compression) . . . . . . . . . . .42

SRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-42

Audio Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Auto Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Auto Noise Cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Change Access Code . . . . . . . . . . . . . . . . . . . . . . .46

Channel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Input Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Front Panel Lock . . . . . . . . . . . . . . . . . . . . . . . . . . .46

TV Time Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Movie Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

TV Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

TV Ratings (Canadian - English) . . . . . . . . . . . . . . .49

TV Ratings (Canadian - French) . . . . . . . . . . . . . . .50

Loudness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Black Enhancement . . . . . . . . . . . . . . . . . . . . . . . . . .36-37

Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36-37

Magic Focus

Auto Convergence . . . . . . . . . . . . . . . . . . . . . . . .7, 55

Manual Convergence . . . . . . . . . . . . . . . . . . . . .56-57

Menu Preference

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Monitor Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 63

CableCARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11,63

Channel Manager . . . . . . . . . . . . . . . . . . . . . . . . . . .44-45

Auto Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . .44

Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Set The Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Signal Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Clock

Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Closed Captions

Noise Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Perfect Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Picture-in-Picture (PIP) . . . . . . . . . . . . . . . . . . . . . . .26-28

Picture-outside-Picture (POP) . . . . . . . . . . . . . . . . . . . . .26

Analog Captions . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Digital Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Color Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Color Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Color Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Convergence (see Magic Focus)

Remote Control

Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-32

Programming Codes . . . . . . . . . . . . . . . . . . . . . .29-32

Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36-37

Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Connecting External Speakers . . . . . . . . . . . . . .5, 14

Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Daylight Saving Correction . . . . . . . . . . . . . . . . . . . . . . .51

Disassembly/Assembly Instructions (57”) . . . . . . . . .71-73

Disassembly/Assembly Instructions (65”) . . . . . . . . .74-76

Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Tint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Event Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Freeze Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21, 28

Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Guide Button on Remote . . . . . . . . . . . . . . . . . . . . . . . .24

Vertical Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Video Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36-39

Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10, 13, 18

Input Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE

IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you and Hitachi America,

Ltd., Home Electronics Division ("HAL-HED"). By using this Hitachi digital television (the "DTV") and its software (the

"Software"), you agree to be bound by the terms of this License Agreement. IF YOU DO NOT AGREE TO BE BOUND

BY THIS LICENSE AGREEMENT, DO NOT USE THIS DTV AND ITS SOFTWARE.

The Software is protected by copyright laws and international copyright treaties, as well as other intellectual property

laws and treaties. The Software is licensed, not sold.

1. LICENSE GRANT. Subject to all of the terms, conditions and restrictions of this License Agreement, HAL-HED grants

to you a limited, revocable, non-exclusive right to use one copy of the Software only on one Hitachi labeled DTV owned

by you.

2. RIGHTS AND LIMITATIONS. Software Not for Resale. You may not resell or otherwise transfer for value the

Software, except that you may transfer the Software as part of a resale of the entire DTV product only.

Prohibition on Reverse Engineering, Decompilation, Disassembly and/or Modification. You may not reverse engineer,

decompile, disassemble or modify the Software.

Separation of Components. The Software is licensed as single product. Its component parts may not be separated for

use on more than one DTV.

No Transfers. You may not transfer, assign, rent, lease, lend or in any way sublicense the Software.

Trademarks. This License Agreement does not grant you any rights to any trademarks.

Third Party Software. You shall not use the Software in combination with any third party software.

3. VIOLATIONS; INDEMNITY. You understand that any use, copying or transfer of the Software, except as permitted

pursuant to this License Agreement, constitutes a violation of legal rights and may subject you to damages and an award

to HAL-HED of attorneys’ fees in connection with any violation of this License. You further understand that you may be

held legally responsible for any copyright infringement or other violation of intellectual property rights that is caused or

encouraged by your failure to abide by the terms of this License Agreement. You agree to defend, indemnify and hold

HAL-HED and its parent and affiliate companies harmless from and against any and all liability resulting from any breach

by you of this License Agreement and/or any use by you of the Software in combination with third party software.

4. COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images,

photographs, animation, video, audio, music, text, and "applets" incorporated into the Software), and any accompanying

printed materials are owned by HAL-HED. All title and intellectual property rights in and to the content which may be

accessed through use of the Software is the property of the respective content owner and may be protected by applica-

ble copyright or other intellectual property laws and treaties. This License Agreement grants you no rights to use such

content. All rights not expressly granted are reserved by HAL-HED. This provision applies to U.S. Government end-

users, who are granted only those rights expressly set forth herein.

5. EXPORT RESTRICTIONS. HAL-HED is licensing the Software for use within North America only. You agree that you

will not export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country

to which the U.S. has embargoed or restricted the export of goods or services, which currently include, but are not nec-

essarily limited to Cuba, Iran, Iraq, Libya, North Korea, Sudan, and Syria, or to any national of any such country, wherev-

er located, who intends to transmit or transport the Software back to such country; (ii) to any person or entity who you

know or have reason to know will utilize the Software in the design, development, or production of nuclear, chemical, or

biological wepons; or (iii) to any person or entity who has been prohibited from participating in U.S. export transactions

by any federal agency of the U.S. government. You warrant and represent that neither the Bureau of Export

Administration (BXA) nor any other U.S Federal Agency has suspended, revoked, or denied your export privileges.

6. NO WARRANTIES. THE SOFTWARE IS PROVIDED "AS-IS, WHERE-IS." HAL-HED MAKES NO WARRANTIES OF

ANY KIND WHATSOEVER REGARDING THE SOFTWARE AND, TO THE MAXIMUM EXTENT PERMITTED BY LAW,

HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH

RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

HEREBY EXPRESSLY DISCLAIMED TO THE MAXIMUM EXTENT PERMITTED BY LAW.

END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE

7. LIMITATION OF LIABILITY. IN NO EVENT SHALL HAL-HED OR ANY OF ITS PARENT OR AFFILIATE COMPA-

NIES BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEM-

PLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE

GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; LOSS OF GOODWILL, EXPENDITURES MADE OR

COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE AGREEMENT OR BUSINESS INTER-

RUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILI-

TY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THE

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

8. NO FAILURE OF ESSENTIAL PURPOSE. YOU AGREE THAT NO FAILURE TO REPAIR A DEFECT, ERROR OR

BUG IN THE SOFTWARE SHALL CONSTITUTE A FAILURE OF THE ESSENTIAL PURPOSE OF THIS LICENSE

AGREEMENT.

9. CRYPTOGRAPHIC SOFTWARE. THIS PRODUCT CONTAINS SOFTWARE DEVELOPED BY THE OpenSSL PRO-

JECT INCLUDING CRYPTOGRAPHIC SOFTWARE WRITTEN BY ERIC YOUNG (THE "CRYPTOGRAPHIC SOFT-

WARE"). THE CRYPTOGRAPHIC SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS'' AND ANY

EXPRESSED OR IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED TO

THE MAXIMUM EXTENT PERMITTED BY LAW. IN NO EVENT SHALL THE OpenSSL PROJECT, ITS CONTRIBU-

TORS, HAL-HED OR ANY OF ITS PARENT OR AFFILIATE COMPANIES BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PRO-

CUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTER-

RUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILI-

TY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THE

SOFTWARE OR THE CRYPTOGRAPHIC SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

10. TERMINATION. This License Agreement may be terminated at any time by HAL-HED effective immediately upon

notice to you.

11. GOVERNING LAW; SEVERABILITY. This Agreement shall be governed and construed in accordance with the laws

of the State of California, without regard to its conflict of laws rules, and any disputes hereunder shall be subject to the

exclusive jurisdiction and venue of the U.S. Federal Courts in the Southern District of California. If any part of this

License Agreement is unenforceable, the remainder shall be valid and binding to the maximum extent permitted by appli-

cable law.

QR61703

York Air Conditioner H3ce120 User Manual
Whisperkool Platinum 042610 User Manual
Sanyo Uf612248p User Manual
Quasar Hq2201gh User Manual
Panasonic Cw Xc244hu User Manual
Motorola Battery Charger Wpln4111 User Manual
MIELE CS 1122 User Manual
MAKITA M4500 User Manual
HP 85027B User Manual
ACER ASPIRE E1 E1 432P User Manual