HITACHI 42HDT20 User Manual

PLASMA TELEVISION

AVC (Audio/Video Control Center) & Plasma Display Monitor

32HDT20 42HDT20

OPERATING GUIDE

IMPORTANT SAFETY INSTRUCTIONS

2-3

4-23

Video

Audio

Ch. Manager

Locks

Setup

Move SEL Sel

FIRST TIME USE

MODE

EXIT

MUTE

THE REMOTE CONTROL

ON-SCREEN DISPLAY

24-39

Video

Audio

Ch. Manager

Locks

40-63

64-74

75-82

Setup

SEL

Move

Sel

USING THE RGB INPUT

OF THE PLASMA TV

USEFUL INFORMATION INDEX

SAFETY TIPS

Read before operating equipment

Follow all warnings and instructions marked on this television.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

15. Televisions are designed to comply with the

recommended safety standards for tilt and stability.

Do not apply excessive pulling force to the front, or top,

of the cabinet which could cause the product to

overturn resulting in product damage and/or personal

injury.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

16. Follow instructions for wall, shelf or ceiling mounting as

recommended by the manufacturer.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use the attachments/accessories specified by the

manufacturer.

17. An outdoor antenna should not be located in the

vicinity of overhead power lines or other electrical

circuits.

18. If an outside antenna is connected to the receiver be

sure the antenna system is grounded so as to provide

some protection against voltage surges and built up

static charges. Section 810 of the National Electric

Code, ANSI/NFPA No. 70-1984, provides information

with respect to proper grounding for the mast and

supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding

connectors, location of antenna-discharge unit,

connection to grounding electrodes and requirements

for the grounding electrode.

ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

12.

Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

ANTENNA

DISCHARGE UNIT

ꢀNEC SECTION 810-20)

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

ꢀNEC SECTION 810-21)

caution

when

moving

the

GROUNDING CONDUCTORS

cart/apparatus combination to avoid

injury from tip-over.

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

ꢀNEC ART 250 PART H)

NEC NATIONAL ELECTRICAL CODE

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

Note to the CATV system installer: This reminder is

provided to call the CATV system installer’s attention to

Article 820-40 of the NEC that provides guidelines for

proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding

system of the building, as close to the point of cable

entry as practical.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into apparatus, the apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

Disposal of this product may require specific

instructions pertaining to your resident state. For

disposal or recycling information, please contact

your local authorities or the Electronic Industries

Alliance: www.eiae.org.

Do not place any objects on the top of the

television which may fall or cause a child to climb

to retrieve the objects.

PREVENTION OF SCREEN BURN

Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed (non-

moving) patterns can cause permanent damage to television receivers. Such “SCREEN BURNS” constitute misuse and are NOT

COVERED by your HITACHI Factory Warranty.

PUBLIC VIEWING OF COPYRIGHTED MATERIAL

Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require

prior authorization from the broadcaster or owner of the video program material.

ACCESSORIES

Check to make sure you have the following accessories before disposing of the packing material.

REMOTE

CONTROL

BATTERIES

POWER CORD

MONITOR

CONNECTION CABLE

IR MOUSE

CABLE

POWER

VCR

SOURCE WIZARD

CBL

STB

TAPE

DVD

AMP

SLEEP

INFO

A/V NET

TV/RGB

MODE

ANT

EXIT

SELECT

VOL

MUTE

R P

VID 1

VID 2

VID 3

PIP CH

PIP

FREEZE

PIP ACCESS

SWAP

PIP MODE

VIDEO

REC

CLU-5723TSI

WALL MOUNT UNIT WM20

(OPTIONAL)

32HDT20 TV STAND SPD32

(OPTIONAL)

SPEAKER ACCESSORIES

(42HDT20 ONLY)

CAUTION: The plasma display wall mount unit WM20 is for use only with Hitachi model 32HDT20 and 42HDT20.

1. Remote Control Unit CLU-5723TSI (P# HL01823).

2. Two “AA” size, 1.5V batteries (P# EQ00021).

3. Two Power Cords (P# EV00832).

5. Two IR Mouse cables (P# EY01641).

6. Speaker Accesories (42HDT20 only).

7. Wall Mount Unit WM20 (Optional).

8. 32HDT20 Stand (P# H520441) (Optional).

4. Monitor Connection Cable (P# EW07193).

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

1. Open the battery cover of the remote control by pushing the notched part of the cover with your fingers and pulling the

cover off.

2. Insert two new “AA” size batteries for the remote control. When replacing old batteries, push them towards the springs

and lift them out.

BOTTOM VIEW

3. Match the batteries to the (+) and (-) marks in the battery compartment.

4. Replace the cover.

Lift up on tab to

remove back cover.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace with the same or equivalent type.

HOW TO SETUP YOUR NEW HITACHI PLASMA TELEVISION

SPEAKER INSTALLATION (MODEL 42HDT20 ONLY)

1. Screw the speaker holder to the speakers as shown below.

Screw x2

Speaker Holder

(R)

(L)

(R)

Speaker Holder

Screw x2

2. Loosen 4 screws (A) (two on the left and two on the right).

3. Completely unscrew 4 screws (B) (two on the left and two on the right).

4. Hook the speaker holders to the loosened screws (A).

5. Screw the speaker holders to the Display Monitor with screws (B).

6. Tighten screws (A).

Insert

horizontally

from the side

Screw in

screws (B)

(R) Speaker

Bottom View

of Speaker

Holder

Unscrew (B)

Completely

Loosen

Screw

(A)

Hook this

portion to

the loose

screws (A).

7. Connect the speaker wires as shown below. (Make sure the core is toward the display monitor side.)

Core

NOTES: Do not connect speakers

simultaneously to the speaker

terminal of the Plasma TV and

an external amplifier.

HOW TO SETUP YOUR NEW HITACHI PLASMA TELEVISION

To take measures to prevent the Plasma Display from tipping over and prevent possible injury it is important to mount the unit

in a stable place.

Securing to a table-top

1. Using wood screws (two) fasten the set to the clamping screw holes on the rear of the Plasma Display stand as shown below.

2. Using commercially available wood screws, secure the set firmly in position.

Wood screw two places

42HDT20

32HDT20

Rear View

Securing to a wall

1. Keep the Plasma Display monitor four inches away from the wall except those hung to the wall mount bracket.

10cm (4 inches) or more

Do not block the ventilation holes of the Plasma Display monitor or the AVC center. Blocking the ventillation holes might cuase fire

or defect.

NOTES: 1.

2. The plasma television has two AC cords, one on the AVC center and the other on the Plasma Display monitor. In case of an

abnormal symptom, unplug both AC cords.

3. If you purchased the wall mount bracket option, please ask for professional installer. Do not install by yourself.

Caution when moving the main unit

As this product is heavy, whenever it is moved, two people are required to transport it safely. Whenever the unit is moved it should be

lifted forward using the two handgrips at the back, and the unit should then be held at the base on both sides for stability. When moving

the Display Monitor, lift the handles and the bottom frame as shown below. Do not grab the speakers or the back cover when lifting.

Handgrips

42HDT20

32HDT20

ANTENNA

Unless your Plasma Television is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is

recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and

multiple image ghosts, an indoor antenna may be sufficient.

LOCATION

Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected

allows a free flow of air to and from the perforated back cover of the set.

To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become

excessively hot, for example, in direct sunlight or near a heating appliance, etc.

HOW TO SET UP YOUR NEW HITACHI PLASMA TELEVISION

VIEWING

The major benefit of the HITACHI Plasma Television is its large viewing screen. To see this

large screen at its best, test various locations in the room to find the optimum spot for viewing.

The best picture is seen by sitting directly in front of the TV and about 8 to 18 feet from the

BEST

VERTICAL VIEWING

ANGLE

screen.

During daylight hours, reflections from outside light may appear on the screen. If so, drapes

3’

or screens can be used to reduce the reflection or the TV can be located in a different section

0’

5’

10’

15’

20’

of the room.

If the TV’s audio output will be connected to a Hi-Fi system’s external speakers, the best

audio performance will be obtained by placing the speakers equidistant from each side of the

receiver cabinet and as close as possible to the height of the picture screen center. For best

stereo separation, place the external speakers at least four feet from the side of the TV, place

the surround speakers to the side or behind the viewing area. Differences in room sizes and

acoustical environments will require some experimentation with speaker placement for best

performance.

4" Minimum

BEST

HORIZONTAL

5’

10’

15’

20’

VIEWING ANGLE

4" Minimum

IMPORTANT NOTES

No. Items

Notes

A buzzing sound might be heard when the plasma display monitor is turned on in a very quiet

Arching sound from

plasma display monitor’s room. This is due to the plasma panel drive circuit when it is functioning. This arching sound

panel.

is normal and it is not a malfunction.

Interference for infrared

equipment.

Some infrared rays are emitted from the plasma display monitor’s panel that might affect other

infrared controlling equipment.

Bright and dark spots

High-precision technology is used to manufacture the plasma display panel; But in some

cases, there are minor defects in some parts of the screen. Points that do not light, points

with brightness different from that of the perphery, points with color different from that of the

periphery, etc. Some pixels will always be on or always off. Please note that this is not a

malfunction.

Picture Image (Spectrum) When receving still picture signals, (e.g. channel number indication or clock indication) for a

while, you can see image-like when the picture varied. This is not a defect.

Display panel surface

The plasma display panel is lighting the phosphors by the discharge of internal radiation. In

temperature is too high some cases, this may cause the temperature of the panel surface to increase. Please note

that this is not a malfunction. The Plasma TV surface temperature is higher than a

Cathode-ray-tube.

Plasma Surface

Transportation

The plasma panel is made from glass. Heavy shock on the front panel might damage it.

When the PDP monitor is transported horizontally, the glass panel has the possibility of being

broken or increasing the picture defects. At the time of transportation, horizontal style is

prohibited. More-over, please treat the plasma panel with great care because of a precision

apparatus. Please instruct transporters so that it should be put into the packing box at the time

of shipment.(There is a possibility that breakage of the panel or defects will increase.)

Rough transportation might cause damage to the panel and pixel failure.

Image retention

The plasma monitor illuminates phosphor to display images. The phosphor has a finite

illumination life. After extended periods of illumination, the brightness of the phosphor will be

degraded to such extent that stationary images would burn-in that part of the screen as

grayed-out images.

Tips to prevent such image retention are:

- Do not display images having sharp brightness differences or hi-contrast images, such as

monochrome characters and graphic patterns, for long.

- Do not leave stationary images appearing for long, but try to refresh them at appropriate

intervals of time, or try to move them using screen saver function.

- Turn down the contrast and brightness controls.

Luminosity and contrast PDP television has luminosity and low contrast compared with CRT television.

10 Granular spots

When a screen is seen at point-blank range, a random fine grain may be visible to a dark part.

11 Disturnbance to video

apparatus

If an apparatus (VCR, etc.) antenna line is arranged near the monitor, the image may shake,

or disturbance may be received.

12 Lip Sync

There is some time lag betweeen the picture and the sound. You can see lip motion that is

delayed compared to the sound.

13 About the use

Electric discharge/luminescence characteristic of the PDP panel also changes with peripheral

temperature. Moreover, since there is also high power consumption value, a specified

environment of PDP

television (temperature) temperature environment is required.

14 Caution on prolonged

storage

Storing the plasma television for a period of more than 2 to 3 months without use might cause

an unstable picture when the set is turned on.

HOOKUP CABLES

Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors.

For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell

audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output

and input connector types required by the various components and the length of each cable.

“F” Type 75-Ohm Coaxial Antenna Connector

300-Ohm Twin Lead Connector

For connecting RF signals (antenna or cable TV) to the

This outdoor antenna cable must be connected to an

antenna jack on the television.

antenna adapter (300-Ohm to 75-Ohm).

Phono Connector

S-Video (Super Video) Connector

Used on all standard video and audio cables which

connect to inputs and outputs located on the rear jack

panel and front control panel.

This connector is used on camcorders, VCRs and laser-

disc players with an S-Video feature in place of the

standard video cable to produce a high quality picture.

AUDIO OUT

3.8mm

RCA TYPE

PLUGS

STEREO

MINI-PLUG

Stereo Cable (3.5 mm plug to 3.5 mm plug)

15 14 13 12 11

This cable is used to connect from external audio out to

the audio input of the AVC Center (ex. RGB 1/2 Input).

D-SUB MINI 15-Pin Cable

This cable is used to connect a computer output to the

D-SUB input located on the rear panel of the AVC

Center. The resolution should be set to correctly to

display the signal on the Plasma Television.

IR Mouse Cable (Provided)

Connect the IR Mouse to the IR ouput on your AVC

center when A/V Network is used. You must place the

IR mouse in front of the corresponding IR window of

your cable box and VCR. This connection allows your

TV to control your cable box and VCR.

Monitor Conection Cable (Provided)

This cable is used to connect the Display Monitor to the

AVC Center.

To outdoor antenna

or CATV cable

ANTENNA CONNECTIONS TO REAR JACK PANEL

VHF (75-Ohm) antenna/CATV (Cable TV)

When using a 75-Ohm coaxial cable system, connect the outdoor antenna or CATV coaxial cable to the

ANT A (75-Ohm) terminal. If you have a second antenna or cable TV system, connect the coaxial cable

to the ANT B terminal.

To second antenna

or cable system

To outdoor VHF

or UHF antenna

VHF (300-Ohm) antenna/UHF antenna

When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads

to screws of the VHF or UHF adapter. Plug the adapter into the antenna terminal on the TV.

To outdoor

antenna or

CATV system

ANT A/ANT B

To UHF

Antenna

When both VHF and UHF antennas are connected

Attach an optional antenna cable mixer to the TV antenna terminal, and connect the cables to the

antenna mixer. Consult your dealer or service store for the antenna mixer.

Antenna mixer

FRONT PANEL CONTROLS

FRONT VIEW

32HDT20

DISPLAY

MONITOR

42HDT20

DISPLAY

MONITOR

STANDBY (RED) ON (GREEN)

MAIN POWER

STANDBY (RED) ON (GREEN)

MAIN POWER

ቦ

ቨ

ቧ

ቦ

ቨ

ቧ

AUDIO/VIDEO

CONTROL

CENTER

AUDIO/VIDEO CONTROL CENTER

PULL

POWER

STANDBY (RED) ON (GREEN)

TruBass

ባ

ብ

VOL

INPUT/EXIT

INPUT 5

PHONES

POWER

STANDBY (RED) ON (GREEN)

MENU/SELECT

VIDEO

L/(MONO)

AUDIO

S-VIDEO

ቦቧ

ቢ ቤ ቪ

ቩ

ቨ

ቢ MENU/SELECT button

This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This

button also serves as the SELECT button when in MENU mode.

ባ INPUT/EXIT button

Press this button to select the desired input, VIDEO 1 to 5, RGB 1/2, or Ant A/B source. Your selection is shown in the top right

corner of the screen. This button also serves as the EXIT button when in MENU mode.

NOTES: Your remote control does not have an INPUT button. To change to video inputs, press VID1~VID5 buttons depending

on the input you wish to switch to (see page 30). Press TV/RGB button on the remote control to change between the

TV’s RGB1, and RGB2 modes.

ቤ CHANNEL selector

Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as

the cursor down (̄) and up (̆) buttons when in MENU mode.

ብ VOLUME level

Press these buttons to adjust the sound level. The volume level will be displayed on the TV screen. These buttons also serve as

the cursor left (̇) and right (̈) buttons when in MENU mode.

FRONT PANEL CONTROLS

ቦ POWER button

Display Monitor “MAIN POWER” button

This power button is for the complete system, and must be turned ON/OFF manually. It is recommended to leave the “MAIN

POWER” to ON condition (lights red) for stand-by mode.

AVC POWER button

The AVC power can be turned ON/OFF maually or by remote control. Turning on the

AVC Power will only turn on the AVC box if the “MAIN POWER” of the display monitor is off.

STANDBY (RED) ON (GREEN)

MAIN POWER

ቧ POWER light indicator

To turn the monitor ON, press the main power switch located on the lower right side of the monitor. A red stand-by indicator lamp

located on the lower right corner of the front bezel will illuminate. The PDP is now ready for remote on/off operation.

Indicating Lamp

Off

Power Status

Off

Operating

When the main power switch is set

OFF.

Lights Red

Off

(Stand-by)

When the main power switch on the display

monitor is ON, and the AVC Center is OFF.

Display monitor MAIN POWER is ON and

AVC Center power is ON.

Lights Green

Lights Orange

(Flashing)

Off

Display monitor MAIN POWER is ON and

and AVC Center power is ON, with no signal

input except antenna (no sync. signal).

(Power Saving)

ቨ REMOTE CONTROL sensor

Point your remote at this area when selecting channels, adjusting volume, etc.

ቩ FRONT INPUT JACKS (for VIDEO: 5)

Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view your favorite show or new recording.

press the VID5 button on the remote control button and VIDEO: 5 appears in the top right corner of the TV screen. If you have

mono sound, insert the audio cable into the left audio jack.

ቪ PHONES JACK

Use this jack for your head-phones. The TV’s internal speakers can also be heard. Turn off the internal speakers (see page 47) if

you wish to listen to the head-phones only.

NOTES: 1. Your HITACHI Plasma TV will appear to be turned OFF (lights orange) if there is no video input when VIDEO: 1, 2,

3, 4, 5, RGB1 or RGB2 is selected. Check the Power Light to make sure the Display Monitor is turned off or in

Stand-by mode (lights red) when not in use.

2. Remote Control can not turn ON/OFF the “MAIN POWER” of the display monitor.

REAR PANEL JACKS

ቦ

ቢ

ቧ

ቨ

ቪ

REAR PANEL OF THE AVC CENTER

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

ቭ

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

ቫ

ቮ

Y/VIDEO

AUDIO

BLASTER

(MONO)

AUDIO

ANT B

AUDIO

AUDIO OUT

ቤ

ባ

ቩ

ብ

ቢ Antenna Input/Output

The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A input can

be displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture. (ANT B cannot be displayed as a

sub-picture.) The antenna output labeled “TO CONVERTER” allows the ANT A connection to pass directly to a different source

such as a cable box, only when ANT B is displayed as a main picture.

ባ Audio/Video Inputs 1, 2, 3 and 4

The VID1~VID4 buttons will select each video source each time they are pressed. Use the audio and video inputs to connect

external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have mono sound, insert the audio cable

into the left audio jack.)

ቤ MONITOR OUT

These jacks provide fixed audio and video signals (ANT A/B, INPUT 2~5) which are used for recording. Use the S-VIDEO Output

for high quality video output. Component signal to Input 1 and 2 will not have monitor output.

ብ AUDIO OUT

These jacks provide fixed audio output for all audio sources (ANT A/B, INPUT1~5, and RGB 1/2) to a separate stereo amplifier.

ቦ S-VIDEO Inputs 3 and 4

Inputs 3 and 4 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.

NOTES: 1. You may use VIDEO or S-VIDEO inputs to connect to INPUT 3 and 4, but only one of these inputs may be used at a

time.

2. S-VIDEO output may be used for recording, only when the input is of S-VIDEO type.

ቧ Component: Y-P_BP_RInputs

Inputs 1 and 2 provide Y-P_BP_Rjacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may

use standard video signal for INPUT 2. INPUT 1 does not accept composite video signal.

DO NOT connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time. S-Video has a higher priority over video input.

NOTES: 1.

2. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the AVC Box’s P input

and the components R-Y output to the AVC Box’s P input.

3. Your component outputs may be labeled Y-C C . In this case, connect the component C output to the AVC Box’s P input and

B R

the component C output to the AVC Box’s P input.

4. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-P P inputs. (See page 43)

B R

5. To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-P P jacks.

B R

REAR PANEL JACKS

ቨ RGB1 - Analog Input

Use this 15-pin D-Sub input for your external devices with RGB output (see page 22).

ቩ RGB1 - Audio Input

Connect audio for RGB1 input.

ቪ RGB2 - Digital Input

Use this RGB2 Digital input for your external devices with digital output capability (see page 22).

ቫ RGB2- Audio Input

Connect audio for RGB2 input.

ቭ To Monitor

Connect the Monitor Connection Cable to the AVC center’s “TO MONITOR” connector, and to the display monitors “FROM AVC”

connector.

ቮ IR Blaster

This jack provides IR output to your external components (VCR, Cable box, DVD player, etc.). With this connection, your external

components can automatically be controlled by the A/V network feature. This connection will allow you to control the external

components with your Plasma Television’s remote control in TV mode.

ቯ Subwoofer Out

Connect the external audio component input to this SUB WOOFER OUT output.

ተ To AVC

Connect the Monitor Connection cable from the AVC center’s “TO MONITOR” to these connectors (“FROM AVC”).

ቱ SUB-POWER button

This power is for serviceman usage.

CONNECTING PLASMA DISPLAY MONITOR TO AVC BOX

1. From the owner’s accessory you will find the Monitor Connector cable.

2. Firmly, and securely insert the Monitor Connection Cable to the rear panel of the AVC box “TO MONITOR” connectors.

3. Insert the other ends of the Monitor Connection Cable to the display monitor rear panel “FROM AVC” connectors.

Back of Display Monitor

42HDT20

Back of Display Monitor

32HDT20

Core

To AC

outlet

Core

To AC

outlet

T A

O M

DIGITAL INPUT

-V

DIO

T 1

(

)

(

)

(

)

(

)

(

)

T A

DIO

O O

O M

DIGITAL INPUT

-V

DIO

T 1

(

)

(

)

(

)

(

)

(

)

DIO

O O

Back of AVC Center

To AC

outlet

To AC

outlet

NOTE: The Display Monitor and the AVC Center have their own AC Power. Both AC cords must be completely plugged in to

the AVC Center and the display monitor, then plug them in to the AC outlets.

CONNECTING EXTERNAL VIDEO SOURCES

The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following

examples:

Front panel of AVC

INPUT 5

PHONES

INPUT 5

PHONES

VIDEO

L/(MONO)

AUDIO

S-VIDEO

VIDEO

L/(MONO)

AUDIO

S-VIDEO

NOTE:

1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture

may be abnormal.

2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable.

3. If you have a mono VCR, insert the audio cable into the left audio jack of your AVC box.

4. S-VIDEO input takes priority over VIDEO input.

5. If you have a VHS or 8mm camcorder, use the VIDEO cable in place of the S-VIDEO cable.

CONNECTING EXTERNAL VIDEO SOURCES

The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your Plasma

TV is dependent on the model and features of each component. Check the owner’s manual of each component for the location of

video and audio inputs and outputs.

The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your

particular assortment of components and features. For best performance, video and audio cables should be made from coaxial

shielded wire.

Before Operating External Video Source

The input mode is changed when the VID1~VID5 button is pressed as shown below. Connect an external source to the INPUT

terminal, then press the VID1~VID5 button as necessary to view the input source. (See page 30)

INPUT MODE SELECTION ORDER

(INPUT)

(ANTENNA)

YPBPR:1

VID1

Ant A

VID1

ANT

CONNECTING A MONAURAL AUDIO SOURCE TO INPUT2~INPUT5

1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the AVC

Center below.

2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.

3. Press the VID2~VID5 button to view the program from the VCR or the laserdisc player. The VIDEO mode disappears

automatically after approximately four seconds.

4. Press the ANT button to return to the previous channel.

Rear Panel of AVC Center

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

AUDIO

BLASTER

(MONO)

AUDIO

ANT B

AUDIO

AUDIO OUT

VIDEO OUT

AUDIO OUT

VCR

Hitachi Model or

Similar Model

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A STEREO VCR OR STEREO LASERDISC PLAYER

Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the AVC

Center below.

Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

Press the VID2~VID5 button to view the program from the VCR or laserdisc player. The VIDEO label disappears automatically

after approximately four seconds.

Press the ANT button to return to the previous channel.

Rear Panel of AVC Center

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

AUDIO

BLASTER

(MONO)

AUDIO

ANT B

AUDIO

AUDIO OUT

Back of

VCR

OUTPUT

VCR

Hitachi Model or

Similar Model

NOTES:

1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output.

(INPUT: 4 in example on page 22) Refer to your VCR operating guide for more information on line input-output

connections.

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING S-VIDEO VCR OR LASERDISC PLAYER

Connect the cable from the S-VIDEO OUT of the S-VHS VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown

on the AVC Center below.

Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

Press the VID3~VID5 button to view the program from the VCR or laserdisc player. The VIDEO label disappears automatically

after approximately four seconds.

Press the ANT button to return to the previous channel.

Rear Panel of AVC Center

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

AUDIO

BLASTER

(MONO)

AUDIO

ANT B

AUDIO

AUDIO OUT

Back of VCR or

Laserdisc Player

S-VIDEO

OUTPUT

VCR or Laserdisc Player

Hitachi Model or

Similar Model

NOTES:

1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output.

(INPUT: 4 in example on page 22) Refer to your VCR operating guide for more information on line input-output

connections.

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A STEREO LASERDISC/DVD PLAYER OR HDTV SET TOP BOX TO INPUT 1 OR 2 COMPONENT: Y-P P .

B R

Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the

AVC Center below.

Connect the cable from the C /P OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (P jack.

Connect the cable from the C /P OUT or R-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (P ) jack.

Connect the cable from the AUDIO OUT R of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/R) jack.

Connect the cable from the AUDIO OUT L of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/L) jack.

Press the VID1/VID2 button, to view the program from the Laserdisc/DVD player or HDTV set top box. The VIDEO label

disappears automatically after approximately four seconds.

Press the ANT button to return to the previous channel.

DVD Player

Hitachi Model or

Similar Model

Back of

DVD Player

OUTPUT

VIDEO

P C P C

AUDIO

R/ R Y

HDTV Set-Top Box

Rear Panel of the AVC Center

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

S-VIDEO

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

AUDIO

BLASTER

(MONO)

AUDIO

ANT B

AUDIO

AUDIO OUT

NOTE:

1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. See page 23 for tips on REAR PANEL CONNECTIONS.

CONNECTING EXTERNAL AUDIO/VIDEO SOURCES

CONNECTING EXTERNAL AUDIO AMPLIFIER

To monitor the audio level of the Plasma TV to an external audio amplifier, connect the system as shown below. The “AUDIO OUT”

from the AVC center is a fixed output. The Volume of the amplifier is controlled by the amplifier, not by the Plasma Television. The

AUDIO OUT terminal outputs all audio sources (ANT A/B, INPUT 1~5 and RGB 1/2).

Rear Panel of the AVC Center

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

AUDIO

BLASTER

(MONO)

AUDIO

ANT B

AUDIO

AUDIO OUT

To Audio Input Terminal

of External Amplifier

INPUT

Stereo System Amplifier

The MONITOR OUT terminal outputs video and audio of ANT A/B and INPUT2~5 only. It does not output component video or RGB

1/2. If a component device is input to INPUT2, no monitor out is available for this output.

Rear Panel of AVC Center

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

AUDIO

BLASTER

(MONO)

AUDIO

ANT B

AUDIO

AUDIO OUT

Optional,

See page 23

S-VIDEO

INPUT

VCR or other external

components

CONNECTING A/V NETWORK

Your Hitachi Plasma Television is equiped with an A/V Network feature. This feature helps to control your external Audio/Video

equipment (VCR, Set Top Box, DVD, etc.). Once this is setup, it allows your IR Mouse connector to control your equipment using

your Hitachi Plasma TV Remote Control. You can use your Hitachi remote control to control the Audio/Video equipment command

without the equipment’s remote control.

The Plasma Television AVC Center has 2 IR BLASTER jacks. Each IR Mouse cable can connect up to 2 external Audio/Video

components. Therefore, you can connect the Plasma Television with up to four components. Please see the following example of

an A/V Network setup between your Hitachi Plasma Television and external Audio/Video equipment (VCR and DVD Player).

CONNECTING EXTERNAL AUDIO/VIDEO COMPONENTS TO IR BLASTER FOR A/V NETWORK

Connect your external Audio/Video components to the AVC Center shown on pages 13~18.

Connect the IR Mouse cable to the IR BLASTER output of the AVC Center.

Place the IR mouse in front of the infrared sensor of the external components you wish to control.

Rear Panel of the AVC Center

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

AUDIO

BLASTER

(MONO)

AUDIO

ANT B

AUDIO

AUDIO OUT

OUTPUT

P /C P /C

OUTPUT

Infrared

Sensor

Infrared

Sensor

DVD Player

VCR

Mouse

Press the A/V NET button on the remote control. Use THUMB STICK ̆ or ̄ to highlight the component you wish to set up.

Use THUMB STICK ̈ to enter component’s “SOFT KEY” control button. The A/V Network Setup Wizard will automatically

start upon the very first use. You can access the Setup Menu Wizard again in the future by pressing the A/V net button and

selecting SETUP.

POWER

VCR

SETUP

Set Top Box

Cable Box

Amplifier

DVD

TV/VCR

Move

NOTES:

1. The AVC Center has two IR BLASTER outputs which can control up to a total of four external components.

2. The IR Mouse must be placed in front of the external components infrared sensor for the A/V Network to work.

3. The correct codes must be entered for each of the Audio/Video components for the A/V Network to function properly.

4. Audio/Video component codes for A/V network are on page 21.

A/V NETWORK SETUP WIZARD

Follow the steps below to setup your A/V network (See page 21 for A/V Network Codes).

There are six steps in the setup procedure (VCR setup example below).

HITACHI AV NET Wizard (step 1 of 6)

HITACHI AV NET Wizard (step 2 of 6)

This Wizard helps you with

VCR connections and settings.

Would you like to setup or

modify your VCR?

Follow the digrams shown in Hitachi’s

Easy Graphic Guide

to connect your VCR.

Carefully position the IR “mouse” in front

of your VCR as shown in the diagrams.

BACK

HITACHI AV NET Wizard (step 3 of 6)

ATTENTION

Find your VCR

The 4-digit code did not match

AV Net’s library. Please check

and re-enter a valid code - - - -

4-digit manufacturers code

and enter it here - - - -

If Error

(Enter Code “9999” to uninstall)

BACK

Proper Code Entered

from page 21.

HITACHI AV NET Wizard (step 4a of 6)

HITACHI AV NET Wizard (step 4b of 6)

Which TV Rear Panel Input

is connected to your VCR?

Which RF channel does your VCR

use to send video to the TV?

(b) Channel 03

(b) ANT A

(

) INPUT 3

) INPUT 4

) INPUT 5

ANT A,B

(

) ANT B

) INPUT 1

) INPUT 2

(

) Channel 04

BACK

HITACHI AV NET Wizard (step 5 of 6)

Turn ON your VCR then press

each of the 3 function keys below.

Your VCR should respond to one of these

keys. Now press NEXT to continue.

POWER

BACK

PLAY

CH UP

HITACHI AV NET Wizard (step 6 of 6)

HITACHI AV NET Wizard

Did your VCR respond to

POWER, PLAY or CH UP?

Press DONE to finish this wizard or

HELP to trouble shoot settings.

Congratulations!

Your VCR is now conected

to your AV network.

DONE

HELP

DONE

From Step 3, once you enter “9999”,

the following message appears.

HELP

HITACHI AV NET Wizard (step 3b of 6)

TROUBLE SHOOTING

This will uninstall VCR

on INPUT 1.

Would you like to proceed?

Please check connections shown

in the EASY GRAPHIC GUIDE.

If connections are correct,

try a different manufacturers code

for your VCR 0 4 3 6

BACK

YES

Enter code “9999” to uninstall the equipment from your A/V Network.

See Remote Control A/V NET button usage on page 27.

AUDIO/VIDEO CODES FOR A/V NETWORK

(not for remote control)

VCR BRAND . . . . . . . . . . . . . . . . . . . . . . . CODE

Admiral . . . . . . . . . . . . . . . . . . . . . . . . 0048, 0209

Adventura . . . . . . . . . . . . . . . . . . . . . . . . . . .0000

Aiko . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278

Aiwa . . . . . . . . . . . . . . . . . . . . . 0307, 0000, 0037

Akai. . . . . . . . . . . . . . . . . 0106, 0053, 0041, 0061

America Action . . . . . . . . . . . . . . . . . . . . . . . 0278

American High . . . . . . . . . . . . . . . . . . . . . . . 0035

Asha. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Audiovox . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Beaumark. . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Bell & Howell . . . . . . . . . . . . . . . . . . . . . . . . 0104

Broksonic . . . . . . . . . . . . 0121, 0184, 0002, 0209,

. . . . . . . . . . . . . . . . . . . . 0211, 0295, 0361, 0479

CCE . . . . . . . . . . . . . . . . . . . . . . . . . . 0072, 0278

Calix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Canon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035

Capehart . . . . . . . . . . . . . . . . . . . . . . . . . . . 0020

Carver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0081

Cineral . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278

Citizen . . . . . . . . . . . . . . . . . . . . . . . . 0278, 0037

Colt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Craig . . . . . . . . . . . 0037, 0072, 0047, 0240, 0271

Curtis Mathes. . . . . 0035, 0041, 0060, 0162, 0760

Cybernex . . . . . . . . . . . . . . . . . . . . . . 0051, 0240

Daewoo. . . . . . . . . . . . . . 0278, 0561, 0020, 0045

Daytron . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0020

Denon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0042

Dynatech . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Electrohome . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Electrophonic . . . . . . . . . . . . . . . . . . . . . . . . 0037

Emerex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0032

Emerson . . . . . . . . 0184, 0002, 0209, 0278, 0036,

. . . . . . . . . . . . . . . 0121, 0211, 0561, 0208, 0294,

. . . . . . . . . . . . . . . 0479, 0061, 0088, 0212, 0000,

. . . . . . . . . . . . . . . 0037, 0043, 0068, 0295, 0361

Fisher . . . . . . . . . . . . . . . 0047, 0104, 0054, 0066

Fuji . . . . . . . . . . . . . . . . . . . . . . . . . . . 0033, 0035

Funai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

GE . . . 0035, 0060, 0048, 0202, 0240, 0760, 0761

Garrard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Go Video . . . . . . . . . . . . . 0432, 0526, 0232, 0643

GoldStar . . . . . . . . . . . . . . . . . . . . . . . 0037, 0038

Gradiente . . . . . . . . . . . . . . . . . . . . . . 0008, 0000

Grundig . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

HI-Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0047

Harley Davidson . . . . . . . . . . . . . . . . . . . . . . 0000

Harman/Kardon. . . . . . . . . . . . . . . . . . 0038, 0081

Harwood. . . . . . . . . . . . . . . . . . . . . . . 0068, 0072

Headquarter . . . . . . . . . . . . . . . . . . . . . . . . . 0046

Hitachi. . . . . . . . . . . . . . . 0042, 0105, 0000, 0041

Hughes Network Systems. . . . . . . . . . . . . . . 0042

JVC. . . . . . . . . . . . . . . . . . . . . . 0067, 0008, 0041

Jensen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0041

KEC . . . . . . . . . . . . . . . . . . . . . . . . . . 0037, 0278

KLH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Keen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0693

Kenwood. . . . . . . . . . . . . . . . . . 0041, 0067, 0038

Kodak. . . . . . . . . . . . . . . . . . . . . . . . . 0035, 0037

LXI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Lloyd's . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0208

Logik . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

MEI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035

MGA . . . . . . . . . . . . . . . . . . . . . 0043, 0061, 0240

MGN Technology . . . . . . . . . . . . . . . . . . . . . 0240

MTC . . . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0240

Magnasonic . . . . . . . . . . . . . . . . . . . . . . . . . 0278

Magnavox. . . . . . . . . . . . 0035, 0081, 0110, 0563,

. . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0039, 0149

Magnin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Marantz . . . . . . . . . . . . . . . . . . . . . . . 0081, 0035

Marta . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Matsushita. . . . . . . . . . . . . . . . . 0035, 0162, 0454

Memorex. . . . . . . . 0104, 0047, 0479, 0000, 0037,

. . . . . . . . . . 0048, 0035, 0046, 0240, 1037, 0307,

. . . . . . . . . . . 0039, 0162, 0209, 0454, 1162, 1262

Minolta . . . . . . . . . . . . . . . . . . . . . . . . 0105, 0042

Mitsubishi. . . . . . . . 0173, 0061, 0043, 0048, 0067

Motorola . . . . . . . . . . . . . . . . . . . . . . . 0035, 0048

Multitech. . . . . . . . . . . . . . . . . . . . . . . 0000, 0072

NAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0058

NEC. . . . . . . . . . . . 0038, 0040, 0041, 0067, 0104

Nikko . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Nikon . . . . . . . . . . . . . . . . . . . . . . . . . 0034, 0253

Noblex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Olympus. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035

Optimus . . . . . . . . 0162, 0454, 1062, 1162, 0048,

. . . . . . . . . . 0058, 1262, 0037, 1048, 0104, 0432

Optonica. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0062

Orion . . . . . . . . . . . 0479, 0002, 0184, 0209, 0295

Panasonic . . . . . . . 0035, 0162, 0454, 1162, 0077,

. . . . . . . . . . . . . . . 1062, 1262, 1362, 0225, 0616

Penney. . . . . . . . . . . . . . 0035, 0240, 0037, 0042,

. . . . . . . . . . . . . . . . . . . . . . . . . 0038, 0040, 0054

Pentax . . . . . . . . . . . . . . . . . . . . . . . . 0042, 0105

Philco . . . . . . . . . . . . . . . . . . . . 0035, 0209, 0479

Philips . . . . . . . . . . . . . . 0081, 0035, 0062, 0618,

. . . . . . . . . . . . . . . . . . . . . . . . . 0110, 1081, 1181

Pilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Pioneer. . . . . . . . . . . . . . . . . . . . . . . . 0058, 0067

Polk Audio . . . . . . . . . . . . . . . . . . . . . . . . . . 0081

Portland . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0020

Profitronic. . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Proscan. . . . . . . . . . . . . . 0060, 0202, 0760, 0761

Protec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Pulsar. . . . . . . . . . . . . . . . . . . . . . . . . 0039, 0051

Quarter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0046

Quartz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0046

Quasar. . . . . . . . . . 0035, 0162, 0077, 0454, 1162

RCA . . . . . . 0060, 0149, 0202, 0042, 0058, 0105,

. . . . . . 0035, 0048, 0077, 0106, 0240, 0760, 0761

Radio Shack . . . . . . . . . . . . . . . . . . . . 0000, 1037

Radix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Randex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037

Realistic . . . . . . . . . . . . . 0000, 0104, 0047, 0048,

. . . . . . . . . . . . . . . 0037, 0035, 0062, 0046, 0066

ReplayTV . . . . . . . . . . . . . . . . . . . . . . 0614, 0616

Ricoh . . . . . . . . . . . . . . . . . . . . . . . . . 0034, 0253

Runco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0039

STS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0042

Samsung. . . . . . . . . . . . . 0045, 0051, 0053, 0240

Samtron . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0643

Sanky . . . . . . . . . . . . . . . . . . . . . . . . . 0039, 0048

Sansui . . . . . 0041, 0479, 0000, 0067, 0209, 0271

Sanyo . . . . . . . . . . . . . . . 0047, 0046, 0104, 0240

Scott. . . . . . . . . . . . . . . . 0184, 0211, 0121, 0043,

. . . . . . . . . . . . . . . . . . . . . . . . . 0045, 0210, 0212

Sears . . . . . . . . . . 0054, 0105, 0037, 0042, 0000,

. . . . . . . . . . . . . . . 0035, 0046, 0047, 0066, 0104

Semp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0045

Sharp . . . . . . . . . . . . . . . . . . . . 0048, 0062, 0738

Shintom . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Shogun. . . . . . . . . . . . . . . . . . . . . . . . 0051, 0240

Singer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072

Sony. . . . . . . . . . . . . . . . 0033, 0034, 0032, 0253,

. . . . . . . . . . . . . . . . . . . . 0000, 0035, 0636, 1032

Sunpak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0253

Sylvania . . . . . . . . . 0035, 0081, 0000, 0043, 0110

Symphonic . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

TMK . . . . . . . . . . . . . . . . . . . . . 0036, 0208, 0240

Tatung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0041

Teac . . . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0041

Technics . . . . . . . . . . . . . . . . . . . . . . . 0035, 0162

Teknika . . . . . . . . . . . . . . . . . . . 0000, 0035, 0037

Thomas . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Tivo . . . . . . . . . . . . . . . . . . . . . . . . . . 0618, 0636

Toshiba . . . . . . . . . . . . . . . . . . 0045, 0210, 0212,

. . . . . . . . . . . . . . . . . . . . . . . . . 0043, 0066, 0366

Totevision . . . . . . . . . . . . . . . . . . . . . . 0037, 0240

Unitech. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Vector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0045

Vector Research . . . . . . . . . . . . . . . . . 0038, 0040

Video Concepts. . . . . . . . . . . . . 0040, 0045, 0061

Videosonic . . . . . . . . . . . . . . . . . . . . . . . . . . 0240

Wards . . . . . 0035, 0060, 0062, 0000, 0047, 0212,

. . . . . . 0240, 0042, 0048, 0072, 0081, 0149, 0760

White Westinghouse . . . . . . . . . 0072, 0278, 0209

XR-1000 . . . . . . . . . . . . . . . . . . 0072, 0000, 0035

Yamaha . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0038

Zenith. . . . . . . . . . . . . . . . . . . . 0039, 0637, 0000,

. . . . . . . . . . . . . . . . . . . . 0033, 0034, 0209, 0479

CABLE BRAND. . . . . . . . . . . . . . . . . . . . . CODE

ABC . . . . . . . 0003, 0007, 0008, 0011, 0014, 0017

Americast . . . . . . . . . . . . . . . . . . . . . . . . . . . 0899

Bell & Howel . . . . . . . . . . . . . . . . . . . . . . . . .0014

Bell South. . . . . . . . . . . . . . . . . . . . . . . . . . . 0899

Contec. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0019

Everquest. . . . . . . . . . . . . . . . . . . . . . . . . . . 0015

Gemini . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0015

General Instrument . . . . . 0276, 0476, 0011, 0810

GoldStar. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0144

Hamlin . . . . . . . . . . . . . . . . . . . 0020, 0009, 0273

Hitachi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0011

Hytex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0007

Jasco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0015

Jerrold . . . . . . . . . . . . . . .0003, 0012, 0276, 0014,

. . . . . . . . . . . . . . . . . . . . 0476, 0011, 0015, 0810

Memorex . . . . . . . . . . . . . . . . . . . . . . . . . . . .0000

Motorola . . . . . . . . . . . . . . . . . . . . . . . 0476, 1106

Oak . . . . . . . . . . . . . . . . . . . . . . . . . . 0019, 0007

Optimus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0021

Pace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0237

Panasonic . . . . . . . . . . . . . . . . . 0021, 0107, 0000

Paragon . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Philips. . . . . . . . . . . . . . . . . . . . . . . . . 0305, 0317

Pioneer . . . . . . . . . . . . . . 0144, 0533, 0877, 1877

Pulsar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Quasar . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0000

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0021

Radio Shack. . . . . . . . . . . . . . . . . . . . . . . . . 0015

Regal . . . . . . . . . . . . . . . . . . . . .0273, 0279, 0020

Rembrandt . . . . . . . . . . . . . . . . . . . . . . . . . . 0011

Runco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0000

Samsung. . . . . . . . . . . . . . . . . . . . . . . . . . . .0144

Scientific Atlanta. . . . . . . . . . . . . . . . . 0008, 0017,

. . . . . . . . . . . . . . . . . . . . . . . . .0477, 0877, 1877

Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0015

Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . 0011

Sony. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006

Sprucer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0021

Starcom . . . . . . . . . . . . . . . . . . . . . . . 0003, 0015

Stargate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0015

Starquest. . . . . . . . . . . . . . . . . . . . . . . . . . . .0015

Tocom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0012

Toshiba. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000

Tusa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0015

United Artists . . . . . . . . . . . . . . . . . . . . . . . . .0007

Zenith . . . . . . . . . . . . . . . . . . . . 0000, 0525, 0899

Yamaha . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0354

RECEIVER BRAND (Amplifier). . . . . . . . . CODE

ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0531

Aiwa. . . . . . . 0121, 0405, 1405, 0158, 0189, 1089

Bose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1229

Capetronic. . . . . . . . . . . . . . . . . . . . . . . . . . .0531

Carver . . . . . . . . . . . . . . . 0189, 0042, 1089, 1189

Casio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

Clarinette. . . . . . . . . . . . . . . . . . . . . . . . . . . .0195

Compaq . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1136

Curtis Mathes . . . . . . . . . . . . . . . . . . . . . . . . 0080

Denon. . . . . . . . . . . . . . . . . . . . .0004, 1160, 1104

Fisher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0042

Garrard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0463

Harman/Kardon . . . . . . . . . . . . . 0891, 0110, 0189

Hewlett Packard . . . . . . . . . . . . . . . . . . . . . . 1181

JBL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0110

JVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0074

Kenwood . . . . . . . . . . . . . . . . . 0027, 1027, 1313,

. . . . . . . . . . . . . . . . . . . . 0042, 0186, 1569, 1570

LXI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0181

Linn. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0189

Lloyd's . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

MCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0039

Magnavox . . . . . . . . . . . . . . . . 0189, 0391, 1089,

. . . . . . . . . . . . . . . . . . . . . . . . . 0531, 1189, 0195

Marantz . . . . . . . . . . . . . . 0189, 1189, 1089, 0039

Modulaire . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

Nakamichi . . . . . . . . . . . . . . . . . . . . . . . . . . 0097

Onkyo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0135

Optimus . . . . . . . . . . . . . 1023, 0181, 0080, 0186,

. . . . . . . . . . . . . . . 0531, 0738, 0801, 0042, 0670

Panasonic . . . . . . . . . . . . 0039, 0367, 0309, 1518

Penney. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

Philips. . . . . . 0189, 1089, 1120, 1189, 1269, 0391

Pioneer . . . . . . . . . . . . . . . . . . 0080, 0014, 0244,

. . . . . . . . . . . . . . . . . . . . 0150, 0531, 0630, 1023

Polk Audio . . . . . . . . . . . . . . . . . . . . . . . . . . 0189

Proscan . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1254

Quasar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0039

RCA . . . . . . . . . . . . . . . . 1254, 0531, 0080, 1023

Realistic . . . . . . . . . . . . . . . . . . . . . . . 0181, 0195

Sansui . . . . . . . . . . . . . . . . . . . . . . . . 0189, 1089

Sanyo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0801

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0186

Sherwood . . . . . . . . . . . . . . . . . . . . . . 0502, 0491

Sony . . . . . . . . . . . 0158, 1158, 1058, 1258, 0474

Soundesign . . . . . . . . . . . . . . . . . . . . . . . . . 0670

Sunfire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1313

Teac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0463

Technics. . . . . . . . . 0309, 0039, 1308, 1518, 1309

Thorens . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1189

Victor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0074

Wards. . . . . . . . . . . . . . . .0014, 0080, 0158, 0189

Yamaha. . . . . . . . . . . . . . . . . . . 0176, 0186, 1176

Yorx.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195

Zenith. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0857

SATELLITE (Set-Top-Box) . . . . . . . . . . . . CODE

AlphaStar . . . . . . . . . . . . . . . . . . . . . . . . . . . 0772

Chaparra . . . . . . . . . . . . . . . . . . . . . . . . . . . 0216

Echostar . . . . . . . . . . . . . . . . . . . . . . . 1005, 0775

Expressvu . . . . . . . . . . . . . . . . . . . . . . . . . . 0775

GE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0566

General Instrument. . . . . . . . . . . . . . . . . . . . 0869

HTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0775

Hitachi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0819

Hughes Network Systems . . . . . 0749, 1142, 1749

JVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0775

Magnavox. . . . . . . . . . . . . . . . . . . . . . 0722, 0724

Memorex. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0724

Mitsubishi . . . . . . . . . . . . . . . . . . . . . . . . . . . 0749

Next Level . . . . . . . . . . . . . . . . . . . . . . . . . . 0869

Panasonic . . . . . . . . . . . . . . . . .0247, 1189, 0701

Philips . . . . . . . . . . 1076, 1142, 0722, 0724, 0749

Proscan . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0392

RCA . . . . . . . . . . . . . . . . 0566, 0392, 0143, 0855

Radio Shack . . . . . . . . . . . . . . . . . . . . . . . . .0869

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . 1109

Sony. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0639

Star Choice . . . . . . . . . . . . . . . . . . . . . . . . . 0869

Toshiba. . . . . . . . . . . . . . . . . . . . . . . . 0749, 0790

Uniden . . . . . . . . . . . . . . . . . . . . . . . . 0724, 0722

Zenith. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0856

AUDIO BRAND . . . . . . . . . . . . . . . . . . . . . CODE

Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . 0010, 0159

Fisher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0052

JVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0073

Jerrold . . . . . . . . . . . . . . . . . . . . . . . . 0459, 0520

Scientific Atlanta . . . . . . . . . . . . . . . . . . . . . . 0460

Sony . . . . . . . . . . . . . . . . . . . . . 0159, 0010, 0576

Starcom. . . . . . . . . . . . . . . . . . . . . . . . . . . . .0459

DVD BRAND . . . . . . . . . . . . . . . . . . . . . . . CODE

Aiwa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0641

Apex. . . . . . . . . . . . . . . . . . . . . . . . . . 0672, 0755

Audiologic. . . . . . . . . . . . . . . . . . . . . . . . . . . 0736

B & K . . . . . . . . . . . . . . . . . . . . . . . . . 0655, 0662

Denon. . . . . . . . . . . . . . . . . . . . . . . . . 0490, 0634

Emerson. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0591

Fisher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0670

GE . . . . . . . . . . . . . . . . . . . . . . . . . . . 0522, 0717

GPX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0769

Go Video . . . . . . . . . . . . . . . . . . . . . . . . . . . 0715

Gradiente . . . . . . . . . . . . . . . . . . . . . . . . . . . 0651

Harman/Kardon . . . . . . . . . . . . . . . . . . . . . . 0582

Hitachi . . . . . . . . . . . . . . . . . . . . . . . . 0573, 0664

Hiteker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0672

JVC . . . . . . . . . . . . . . . . . . . . . . . . . . 0623, 0558

Kenwood. . . . . . . . . . . . . . . . . . 0737, 0682, 0534

Konka . . . . . . . . . . . . . . . 0719, 0711, 0720, 0721

Magnavox. . . . . . . . . . . . . . . . . . . . . . 0503, 0675

Marantz . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0539

Mitsubishi . . . . . . . . . . . . . . . . . . . . . . . . . . . 0521

Onkyo. . . . . . . . . . . . . . . . . . . . . . . . . 0627, 0503

Optimus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0571

Oritron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0651

Panasonic . . . . . . . . . . . . 0490, 0677, 0678, 0632

Philips. . . . . . . . . . . . . . . . . . . . . . . . . 0539, 0503

Pioneer . . . . . . . . . . . . . . . . . . . 0571, 0525, 0632

Princeton . . . . . . . . . . . . . . . . . . . . . . . . . . . 0674

Proscan . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0522

RCA . . . . . . . . . . . . . . . . 0522, 0571, 0704, 0717

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . 0573

Sanyo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0670

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0630

Sherwood. . . . . . . . . . . . . . . . . . . . . . . . . . . 0633

Sony. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0533

Technics. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0490

Techwood. . . . . . . . . . . . . . . . . . . . . . . . . . . 0692

Theta Digital . . . . . . . . . . . . . . . . . . . . . . . . . 0571

Toshiba. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0503

Yamaha . . . . . . . . . . . . . . . . . . . . . . . 0490, 0545

Zenith . . . . . . . . . . . . . . . . . . . . . . . . . 0591, 0503

SET TOP BOX BRAND . . . . . . . . . . . . . . . CODE

AOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1061

Magnavox. . . . . . . . . . . . . . . . . . . . . . . . . . . 0818

Mitsubishi . . . . . . . . . . . . . . . . . . . . . . . . . . . 1002

Panasonic. . . . . . . . . . . . . . . . . . . . . . . . . . . 1120

Philips. . . . . . . . . . . . . . . . . . . . . . . . . 0818, 1061

Pioneer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010

Princeton. . . . . . . . . . . . . . . . . . . . . . . 0113, 0295

Samsung . . . . . . . . . . . . . . . . . . . . . . . . . . . 1190

Sensory Science. . . . . . . . . . . . . . . . . . . . . . 1126

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0850

AMPLIFIER BRAND . . . . . . . . . . . . . . . . . CODE

Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0406

Carver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0269

Curtis Mathes . . . . . . . . . . . . . . . . . . . . . . . .0300

Denon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0160

GE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0078

Harman/Kardon . . . . . . . . . . . . . . . . . . . . . . .0892

JVC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0331

Linn. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0269

Luxman . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0165

Magnavox. . . . . . . . . . . . . . . . . . . . . . . . . . . 0269

Marantz. . . . . . . . . . . . . . . . . . . 0269, 0321, 0892

Nakamichi . . . . . . . . . . . . . . . . . . . . . . . . . . 0321

Optimus . . . . . . . . . . . . . . . . . . . . . . . 0395, 0300

Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . 0308

Parasound . . . . . . . . . . . . . . . . . . . . . . . . . . 0246

Philips. . . . . . . . . . . . . . . . . . . . . . . . . 0269, 0892

Pioneer. . . . . . . . . . . . . . . . . . . . . . . . 0013, 0300

Polk Audio . . . . . . . . . . . . . . . . . . . . . 0269, 0892

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0300

Realistic. . . . . . . . . . . . . . . . . . . . . . . . . . . . .0395

Sansui . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0321

Sony. . . . . . . . . . . . . . . . . . . . . . . . . . 0689, 0220

Soundesign. . . . . . . . . . . . . . . . . . . . . 0078, 0211

Technics . . . . . . . . . . . . . . . . . . . . . . . 0308, 0521

Victor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0331

Wards . . . . . . . . . . . . . . . . . . . . 0013, 0078, 0211

REAR PANEL CONNECTIONS

Outside antenna or

cable TV coaxial cable

RGB

OUTPUT

2-Way signal splitter

Rear Panel of Display Monitor

1 1 1 2 1 3 1 4 1 5

1 0

AUDIO OUT

DIGITAL

VCR #1

OUTPUT

OUTPUT CAPABILITY

ANT

DIGITAL OUTPUT

_S-VIDEOV

AUDIO OUT

(PROVIDED)

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

Please use Hitachi specified cable.

CONVERTER

Rear Panel of

AVC Center

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

AUDIO

BLASTER

(MONO)

AUDIO

ANT B

AUDIO

AUDIO OUT

OUTPUT

INPUT

Cable TV Box

INPUT

OUTPUT

P /C P /C

Stereo System Amplifier

S-VIDEO

OUTPUT

INPUT

S-VIDEO

Laserdisc player, VCR,

camcorder, etc.

HDTV Set-Top Box

DVD Player

VCR #2

CONNECT TO

IR BLASTER

(PROVIDED)

CONNECT TO

IR BLASTER

(PROVIDED)

NOTE:

Cables are optional, except when specified.

TIPS ON REAR PANEL CONNECTIONS

S-VIDEO connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections

in place of the standard video connection if your device has this feature.

If your device has only one audio output (mono sound), connect it to the left audio jack on the AVC Center.

Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.

A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output (INPUT: 4 in the

example on page 22). Refer to your VCR operating guide for more information on line input-output connections.

Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack.

COMPONENT: Y-P P (Input 1 & 2) connections are provided for high performance components, such as DVD players and set-

B R

top-boxes. Use these connections in place of the standard video connection if your device has this feature.

Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s P input

and the components R-Y output to the TV’s P input.

Your component outputs may be labeled Y-C C . In this case, connect the components C output to the TV’s P input and the

B R

components C output to the TV’s P input.

It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-P P inputs. (See page 43)

B R

Y-P P

To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the

Y-P P signal only.

jacks.

B R

Input 1 can accept component

Input 2 can accept both component Y-P P and composite video signal.

B R

You may use VIDEO or S-VIDEO inputs to connect to INPUT 3, 4 or 5, but only one of these, VIDEO or S-VIDEO, may be used at

a time for each input. S-VIDEO has priority over VIDEO.

S-VIDEO output may be used for recording only when the input is of S-VIDEO type.

ASPE

EXIT

ANT

MUTE

REMOTE

In addition to controlling all the functions on your HITACHI Plasma TV, the new remote control is designed to operate different

types of VCRs, CATV (Cable TV) converters, set-top-box, satellite receiver, DVD players, and other audio/video equipment with

one touch. Basic operation keys are grouped together in one area.

To operate your Plasma TV, point the remote control at the remote sensor of the AVC box/Display Monitor and press the TV but-

ton. The TV button will blink, indicating that the remote will now control your television.

To operate your VCR, point the remote at the remote sensor of the VCR and press the VCR button. The VCR button will blink,

indicating that the remote will now control your VCR. (See page 34 for instructions on how to program the remote to control your

VCR.)

To operate your cable box, point the remote at the remote sensor of the cable box and press the CABLE (CBL) button. The CBL

button will blink, indicating that the remote will now control your cable box. (See page 35 for instructions on how to program the

remote to control your cable box.)

To operate your set-top-box or satellite receiver point the remote at the remote sensor of the set-top-box and press the SET-TOP-

BOX (STB) button. The STB button will blink, indicating that the remote will now control your set-top-box. If you have a satellite

receiver, use this button to program your satellite receiver. (See page 36 for instructions on how to program the remote to con-

trol your set-top-box.)

To operate your DVD player, point the remote at the remote sensor of the DVD player and press the DVD button. The DVD but-

ton will blink, indicating that the remote will now control your DVD player. (See page 37 for instruction on how to program the

remote to control your DVD player.)

To operate additional audio equipment, point the remote at the remote sensor of the component you wish to control and press

the CD, TAPE or AMP button. This button will blink, indicating that the remote will now control the desired component. (See page

38 for instructions on how to program the remote to control additional Audio equipment.)

POWER

ባ

ቢ These buttons allow the remote to control your TV, VCR,

VCR

SOURCE WIZARD

CBL

STB

cable box, satellite receiver, DVD player, or other

Audio equipment depending on which mode is

chosen, as explained above.

ቢ

TAPE

DVD

AMP

ባ,ቤ LIGHT BUTTON

ቤ

When you are in a dark room, press the light button ባ

on the remote to light up the buttons shown in ቤ and the

source button will blink. The light will stay on for about 8

seconds if the light button is not pressed again. These

buttons will not appear to illuminate if the room is too

bright.

SLEEP

INFO

A/V NET

ASPECT

TV/RGB

MODE

ANT

EXIT

SELECT

ቤ

VOL

MUTE

VCR PLUS+

SVCS

LAST CH

UIDE/TV

VID 1

VID 2

VID 4

FREEZE

VID 3

PIP

PIP CH

PIP ACCESS

SWAP

VIDEO

PIP MODE

ቤ

REC

CLU-5723TSI

ANT

TV/R

PECT

HOW TO USE THE REMOTE TO

CONTROL YOUR PLASMA TV

MUT

ቢ

ቤ

ባ

POWER

VCR

ብ

ቦ

CBL

STB

SOURCE WIZARD

TAPE

DVD

AMP

ꢀ

ቨ

ቩ

ቪ

ቫ

SLEEP

INFO

ቯ

ቭ

ቮ

ቲ

ት

A/V NET

ASPECT

ቱ

ተ

ታ

ቴ

TV/RGB

MODE

ANT

EXIT

SELECT

VOL

ቩ

ት

MUTE

SVCS

ቶ

LAST CH

VID 1

GUIDE/TV

VID 4

FREEZE

VID 3

PIP

PIP CH

PIP ACCESS

SWAP

VIDEO

PIP MODE

REC

CLU-5723TSI

ᕃ POWER button

Press this button to turn the Plasma TV on or off when the remote is in TV mode. (See page 24 for instructions on how to set the

remote control to TV mode.)

ባ TV button

When the TV button is pressed, it will blink, to indicate the remote is in TV mode.

ቤ VCR button

When the VCR button is pressed, it will blink to indicate the remote is in VCR mode. (see page 34)

ብ CABLE (CBL)

When the CABLE button is pressed, it will blink to indicate the remote is in CABLE mode. (see page 35)

ቦ SET-TOP-BOX (STB)

When the STB button is pressed, it will blink to indicate the remote is in STB mode. (see page 36)

If you have a Satellite receiver, use this button to program your Satellite receiver. (see page 36)

ꢀ DVD button

When the DVD button is pressed, it will blink to indicate the remote is in DVD mode. (see page 37)

HOW TO USE THE REMOTE

ASPE

EXIT

ANT

MUTE

TO CONTROL YOUR PLASMA TV

ቨ CD, TAPE, AMP buttons

When pressed, each of these buttons will blink to indicate the remote is in Audio mode. (see page 38)

ቩ CHANNEL selector buttons

CHANNEL selector buttons are used to select channels, lock access code, etc.

Enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel you

wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the “1” button, wait until two dashes

appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons.

Channel selection may also be performed by pressing CH up (̆) or down (̄).

NOTE:

The Plasma TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode. (see page 58)

ቪ SLEEP button

Press this button to display the sleep timer in the lower left corner of the screen. Every subsequent press of this button will add 15

minutes to this timer, up to a maximum of three hours. Once set, use INFO when you want to view time remaining. If the SLEEP

button is pressed while the timer is set, it will reset to the original condition.

ቫ INFO button

Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second

audio program (SAP), the time, CHANNEL ID and if the SLEEP timer is set.

S - IN: 3

When an S-VIDEO

Input is connected to

VIDEO: 3.

Signal Format

Received

Broadcast

Rating

Main Picture Source

Audio Selected

Audio

Stereo (480i)

ST/SA

TV-PG DLSV

PIP TV-PG DLSV

Ant A 15

ABCDEFG

10:10 AM

Channel ID/Video ID

Time

Broadcast

Wide

Mode

PIP Ant A 46-1234

PIP/Sub-Picture

Source

16:9 Standard

Picture

Mode

YPBPR:1

When a COMPONENT

Movies

C.C. On

Closed

Captioning

VIDEO: Y-P P Input

B R

Off Timer

TV Time Out

Sleep Timer

Off 10:05 AM

Time Lock 10:05 AM

Sleep 0:01

is connected to

VIDEO: 1.

PIP/Sub-Picture

ቭ ANTENNA button

The ANT button will select between Antenna A and Antenna B each time the button is pressed.

Ant A 10

Ant B 28

ANT

ቮ TV/RGB button

Press this button to toggle between RGB1, RGB2 and TV mode.

HOW TO USE THE REMOTE

TO CONTROL YOUR PLASMA TV

ቯ A/V NET button

Press this button to access the Audio/Video network (A/V Net) menu. The A/V Net allows the user to control external components

with the Plasma TV’s remote control.

When you press the A/V NET button, the following window will pop up within the Display Monitor screen. The window will disap

pear after eight seconds if you don’t press any buttons.

The A/V Net Setup Wizard will automatically start upon the very first use. (see page 19-21).

THUMBSTICK ̆ or ̄ to highlight the equipment you wish to control or setup.

Use THUMBSTICK ̆, ̄, ̇, ̈ to navigate and SELECT to select button. The command on the button is passed through the IR

mouse and onto the AUDIO/VIDEO equipment. These on-screen buttons are called “Soft Keys”.

This window shows the available Audio/Video equipment soft keys. The equipment list will scroll up or down but the selected

equipment will always stay on top.

The button at the lower right side

indicates that there are more soft

keys available. Press this button

POWER

VCR

to select between the two pages.

SETUP

Set Top Box

Cable Box

Amplifier

DVD

THUMB

STICK

TV/VCR

SELECT

Move

EXIT

Select

Move

SEL

THUMB

STICK

SELECT

POWER

INFO

POWER

INFO

Set Top Box

Cable Box

Amplifier

DVD

Cable Box

Amplifier

DVD

SETUP

THUMB

STICK

VCR

SELECT

RETURN

VCR

Set Top Box

Move

THUMB

STICK

SELECT

Amplifier

DVD

POWER

INPUT

VOL

DVD

POWER

SETUP

VCR

THUMB

STICK

VCR

Set Top Box

Cable Box

Amplifier

Set Top Box

Cable Box

SELECT

Move

HOW TO USE THE REMOTE

TO CONTROL YOUR PLASMA TV

ተ ASPECT button

Press this button to quickly change the picture format ASPECT ratio.

Depending on the input signal, the picture format ratio allows you to adjust the images through the following options.

4:3 STANDARD

Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the

left and right of the image to preserve the original aspect ratio of the source. Note: Use this mode for

only 15% of your total viewing time to prevent uneven aging of the phospors. Phosphors in the lighted

area of the picture will age more rapidly than the black areas.

4:3 EXPANDED

use this aspect mode to display conventional (4:3) sources by expanding the outer edges of the image

to fill the 16:9 screen. The center of the image remains unaltered.

4:3 Zoom1/Zoom2

16:9 STANDARD

Use these aspect modes to zoom in on conventional (4:3) sources.

Use this aspect mode to display 16:9 sources like HDTV and DVD’s preserving the original 16:9 aspect

ratio.

(1) NTSC/480i/480p Input

4:3

INPUT

4:3 STANDARD

16:9 STANDARD

4:3 EXPANDED

4:3 ZOOM1

4:3 ZOOM2

16:9 STANDARD

(2) 480i/480p INPUT

16:9

INPUT

4:3 EXPANDED

4:3 ZOOM1

4:3 ZOOM2

16:9 STANDARD

(3) 720p/1080i INPUT

NOTES: 1. The Aspect Style setting you select for an ANT input will

automatically be set for the other ANT inputs. However,

all five video inputs have independent Aspect Style set-

tings.

16:9

INPUT

HOW TO USE THE GENIUS REMOTE TO CONTROL

YOUR PLASMA TV

(4) RGB1/RGB2 ASPECT DISPLAY MODE.

RGB1 INPUT SIGNAL

RGB2 INPUT SIGNAL

MODE 1

MODE 2

VGA

480p

720p

1080i

VGA

480p

720p

1080i

VGA

480p

720p

1080i

ASPECT

MODE

REAL

REAL(1)

REAL

NORMAL

NORMAL NORMAL NORMAL(1)

AVAILABILITY FULL

NORMAL NORMAL NORMAL

FULL

FULL (1) FULL (2) FULL (2)

FULL FULL (3) FULL (2) FULL (2) FULL

FULL FULL (2) FULL (2) FULL (2)

For numbers in ( ), please see corresponding note below.

NOTES: 1. Lack of raster can be seen in RGB1 when a 480p signal is input.

2. AUTO ADJUST function (see page 72) is not available in 720p, 1080i, and (480p/VGA~RGB2 Mode 2 only) input signal.

3. Horizontal Phase is shifted in RGB2 when 480p signal is input.

4. All FULL aspect mode, only 95% of information can be displayed (5% is treated as overscan).

ቱ MODE button

Press this button repeatedly to select between Sports, News, Movies, and Music.

ቲ MENU button

The MENU button will start the On-Screen Display.

ታ EXIT button

When in MENU mode, this button will exit all On-Screen Displays.

ቴ THUMB STICK/SELECT button

All the On-Screen Display features can be set or adjusted by using the THUMB STICK (Except for numeric entries).

The THUMB STICK will highlight functions or adjust and set different features. Press the THUMB STICK toward desired direction

and press down to SELECT.

When no on-screen displays are on the TV screen, use THUMB STICK ̇ or ̈ to access the Favorite Channels feature.

To add channels to Favorite Channels, use the number keys to enter the channel number. Use THUMB STICK ̈ to highlight “Add”,

then press SELECT to store the channel to the Favorite Channel feature.

Favorite Channels

Add

Ant

A 8

Ant

A 8

Del

THUMB

STICK

THUMB

STICK

THUMB

STICK

- - - - -

SELECT

SEL Select

Move

To delete (Del) the channel from the Favorite Channel, use THUMB STICK ̆ , ̄ to highlight the channel, then THUMB STICK ̈

to highlight Delete (Del) and press SELECT to delete.

To view a Favorite Channel use THUMB STICK ̆ , ̄ to highlight the channel and press SELECT to view.

ASPE

HOW TO USE THE REMOTE

EXIT

ANT

MUTE

TO CONTROL YOUR PLASMA TV

ት VOLUME, MUTE button

Press the VOLUME up (̆) or down (̄) button until you obtain the desired sound level.

To reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc., press the MUTE button. Press the

MUTE button again to turn the sound off completely (MUTE). To restore the sound, press the MUTE button one more time, or press

the VOLUME Up (̆) button.

Volume

Soft Mute 8

Mute

Closed Captioning will display when MUTE/SOFT MUTE is on and Closed Caption is set to AUTO (See page 63).

ቶ LAST CHANNEL (LAST CH) button

Use this button to select between the last two channels viewed. (Good for watching two sporting events, etc.)

Ant A 39

Ant A 10

LAST CH

PICTURE-IN-PICTURE buttons

See separate section on pages 31~33 for a description.

PIP CH button

Use the PIP CH button to select between main picture and sub-picture tuning. The channel number which is highlighted indicates

what channel is being controlled.

VID1 ~ VID5

When the remote control is in TV mode, press these buttons to directly select the video input sources between the five video inputs.

When the remote control is in Set-Top-Box mode (STB) these buttons will control the Set-Top-Box or satellite receiver, and execute

the secondary function labeled.

YPBPR:1

VID1

Stereo

ST/SA

Ant A 28

TAKA

Video:2

VID2

VID 1

VID 2

VID 3

Ant

Video:4

VID4

Video:5

VID5

Video:3

VID3

VID 4

VID 5

VIDEO button

Press this button to directly access the VIDEO adjustment menu.

ANT

TV/R

PECT

MUT

PICTURE-IN-PICTURE (PIP)

Your HITACHI Plasma TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature allows

you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The Dual

Tuner can operate with only one input (ANT A only) or two inputs (ANT A and ANT B).

ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture.

To select between main picture and PIP sub-picture tuning, press the PIP CH button on the remote. The highlighted channel display will

move with every press of the PIP CH button. When the top channel display is highlighted, channel tuning is for the main picture. When

the lower channel display is highlighted, channel tuning is for the PIP sub-picture.

The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV

program while viewing other programs from the ANT A source or any of the video inputs.

EXIT

ቤ

SELECT

ANT A

VOL

RGB 1

ANALOG INPUT

RGB 2

DIGITAL INPUT

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

MUTE

VCR PLUS+

LAST CH

UIDE/TV

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

VID 2

VID 4

FREEZE

AUDIO

VID 3

BLASTER

(MONO)

AUDIO

PIP

PIP CH

ANT B

ብ,ቦ

ባ

ቢ

ቤ

AUDIO

PIP ACCESS

SWAP

VIDEO

PIP MODE

AUDIO

AUDIO OUT

Back of

VCR

OUTPUT

REC

VCR

Hitachi Model or

Similar Model

CLU-5723TSI

Use above connection to view VCR program as a sub-picture while viewing another program as main picture (ANT A, ANT B, V:1

V:2, V:3, V:4, or V:5). You may also view the VCR program as a main picture while viewing another program as a sub-picture (ANT

A, V:1 V:2, V:3, V:4, or V:5).

ቢ PIP button

Press the PIP button and a sub-picture will appear in one of the two modes (SPLIT or SURF), depending on the last selection of

the PIP mode. To change the PIP mode, use the PIP MODE button to cycle through the two modes.

SPLIT MODE PIP

Press the PIP button and a sub-picture appears in one of the two modes (SPLIT or SURF), depending on the last selection of the

PIP mode. Press the PIP button again to remove the sub-picture from the screen. Use the PIP CH button to select between main

and sub-picture tuning control (indicated by green highlighted channel display.) Press the VID1, VID2, VID3, VID4 or VID5 button

when sub-picture channel tuning is being controlled, to change between VIDEO 1 to VIDEO 5 and ANT:A source. (ANT B source

cannot be viewed as a sub-picture.)

Split mode PIP displays the main picture and sub-picture evenly on the screen.

Ant A 10

Ant A 12

Sub Picture

Main Picture

NOTES: 1. When ANT B is selected as the main channel, the SWAP feature is disabled.

2. Only sound from the main picture can be heard.

ASPE

EXIT

ANT

MUTE

PICTURE-IN-PICTURE (PIP)

SURF MODE PIP

This feature will automatically scan all active channel numbers (those set in memory) and display them as PIP sub-pictures, along

the right edge of the screen. Press the PIP button a second time to remove the sub-pictures from the screen.

Ant A 28

PIP

NOTES: 1. If no buttons are pressed when in SURF mode, auto-scanning will continuously scan channels in memory. (see

page 59).

2. If a channel is changed during this SURF scanning, sub-pictures will be removed from the screen.

3. SURF MODE PIP is allowed only when ANT A is selected as the main channel.

4. If MOVIE/TV RATINGS LOCK setting is ON, PIP SURF mode will be deactivated.

5. CLOSED CAPTION will not appear when PIP SURF mode is on.

ባ SWAP button

If you wish to switch what is being shown on the main picture to the sub-picture, press the SWAP button.

Ant A 10

Ant A 12

Ant A 10

SWAP

SPLIT

NOTES: 1. The SWAP button will only operate in SPLIT PIP mode.

2. The SWAP function will not operate if ANT B input is set as the main channel (ANT B input cannot be displayed as

a sub-picture.)

ቤ PIP MODE button

To change between the two PIP modes (moving picture - SPLIT or SURF; freeze picture - SPLIT or STROBE) press the PIP

MODE button when PIP is ON. Each press of this button will change PIP to a different mode. Pressing this button two times

will cycle through both PIP modes.

Ant A 12

Ant A 10

PIP MODE

ANT

TV/R

PECT

MUT

PICTURE-IN-PICTURE (PIP)

ብ FREEZE button (With PIP OFF)

Press the FREEZE button to freeze the picture, depending on the PIP mode selected (SPLIT or STROBE). This is convenient

when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the

picture to motion, press the FREEZE button again.

To change FREEZE modes, use the PIP MODE button to cycle through the two modes.

SPLIT FREEZE(with PIP off)

PIP should be in SPLIT mode. Press the FREEZE button to freeze the picture you are currently viewing (only the right sub-picture

will freeze). Press this button again or PIP to return to normal viewing.

Freeze Picture

Main Picture

FREEZE

STROBE FREEZE(with PIP OFF)

PIP should be in SURF mode. Press the FREEZE button to freeze three frames of the picture you are currently viewing. Press

this button again or PIP to return to normal viewing. This feature is useful for viewing a moving picture that has many details, for

example, a close play in a sporting event or a golf swing.

FREEZE

NOTES: 1. Each freeze frame is delayed about 0.1 (1/10) second.

2. Freeze will only work when PIP is off.

ASPE

EXIT

ANT

MUTE

USING THE REMOTE TO CONTROL VCR FUNCTIONS

Operating the precoded function for your VCR.

This remote is designed to operate different types of VCRs. You must first program the remote to match the remote command set of

your VCR. (refer to page 39 for pre-codes)

1. Turn ON your VCR.

2. Aim the remote control at the front of your VCR.

3. Press and release the VCR button to switch to VCR pre-coded mode.

4. Hold down the VCR button on the remote and enter the two digit preset code that matches your VCR, as shown on page 39. The

VCR button light will flash 3 times if the code was accepted.

5. Aim the remote at the VCR and press the POWER button. The remote will turn off your VCR if the correct two digit preset code is

entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off, try a different two digit

preset code.

6. The remote will now control your VCR.

POWER

ባ

ቢ

VCR

SOURCE WIZARD

CBL

STB

TAPE

DVD

AMP

NOTES:

1. If your VCR cannot be operated after performing the

above procedures, your VCR’s code has not been

precoded into the remote.

2. In the unlikely event that your VCR cannot be operated

after performing the above procedures, please consult

your VCR operating guide.

ባ

SLEEP

INFO

A/V NET

ቤ

ASPECT

TV/RGB

MODE

ANT

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

4. The MENU button will act as the VCR MENU button for

HITACHI VCRs.

ባ

ቤ

EXIT

ቤ

SELECT

VOL

ባ

MUTE

VCR PLUS+

LAST CH

UIDE/TV

VID 1

VID 5

5. The LAST CH button will act as your VCR ENTER button

if required.

6. The SLEEP button will act as your VCR ‘100’ button if

required.

VID 2

VID 4

FREEZE

VID 3

PIP

PIP CH

ቤ

PIP ACCESS

SWAP

VIDEO

PIP MODE

ቢ VCR Button

ባ

This button allows the remote to control your VCR by set-

ting it to VCR mode.

REC

ባ PRECODED VCR Buttons

These buttons transmit the chosen precoded VCR codes.

For some VCRs, you must press the RECORD button twice

to record a program.

CLU-5723TSI

ቤ EXCLUSIVE TV Buttons

These buttons are for operating the TV.

MY VCR CODE IS:

NOTE:

Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR.

ANT

TV/R

PECT

MUT

USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS

Operating the precoded function for your cable box.

This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote command set

of your cable box. (refer to page 39)

1. Turn ON your cable box.

2. Aim the remote control at the front of your cable box.

3. Press and release the Cable (CBL) button to switch to Cable pre-coded mode.

4. Hold down the CBL button on the remote and enter the two digit preset code that matches your cable box as shown on page 39.

The CBL button light will flash 3 times if the code was accepted.

5. Aim the remote at the cable box and press the POWER button. The remote will turn off your cable box if the correct two digit pre-

set code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try

a different two digit preset code.

POWER

ባ

6. The remote will now control your Cable box.

ቢ

VCR

SOURCE WIZARD

CBL

STB

NOTES:

TAPE

1. If your cable box cannot be operated after performing the

above procedures, your cable box code has not been

precoded into the remote.

DVD

AMP

ባ

2. In the unlikely event that your cable box cannot be

operated after performing the above procedures, please

consult your cable box operating guide.

SLEEP

INFO

ቤ

A/V NET

ASPECT

TV/RGB

MODE

ANT

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

EXIT

SELECT

ቤ

VOL

ባ

4. The LAST CH button will act as the cable box ENTER

button if required.

ቤ

MUTE

VCR PLUS+

SVCS

LAST CH

UIDE/TV

VID 1

VID 5

VID 2

VID 4

FREEZE

VID 3

PIP

PIP CH

5. The SLEEP button will act as your cable box ‘100’ button

if required.

PIP ACCESS

SWAP

ቤ

VIDEO

PIP MODE

6. The ANT button will act as the TV/STB button when in

STB mode.

REC

ቢ CABLE (CBL) button

This button allows the remote to control your cable box by

setting it to CABLE mode.

CLU-5723TSI

ባ PRECODED CABLE BOX buttons

These buttons transmit the chosen precoded cable codes.

ቤ EXCLUSIVE TV buttons

These buttons are for operating the TV.

MY CABLE BOX CODE IS:

NOTE:

Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box.

ASPE

USING THE REMOTE TO CONTROL

EXIT

ANT

MUTE

SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS

Operating the precoded function for your set-top-box/satellite receiver.

This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the

remote command set of your set-top-box/satellite systems. (refer to page 39)

1. Turn ON your set-top-box/satellite systems.

2. Aim the remote control at the front of your set-top-box/satellite systems.

3. Press and release the SET-TOP-BOX (STB) button to switch to set-top-box/satellite pre-coded mode.

4. Hold down the STB button on the remote and enter the two digit preset code that matches your set-top-box/satellite receiver as

shown on page 39. The STB button light will flash 3 times if the code was accepted.

5. Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satel-

lite receiver if the correct two digit preset code is entered. When this occurs, the remote control is programmed for your set-top-

box/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different two digit preset code.

6. The remote will now control your set-top-box/satellite receiver.

POWER

ባ

NOTES:

VCR

SOURCE WIZARD

CBL

STB

ቢ

ባ

1. If your set-top-box/satellite receiver cannot be operated

after performing the above procedures, your set-top-

box/satellite receiver code has not been precoded into the

remote.

TAPE

DVD

AMP

2. In the unlikely event that your set-top-box/satellite

receiver cannot be operated after performing the above

procedures, please consult your set-top-box/satellite

receiver operating guide.

SLEEP

INFO

A/V NET

ASPECT

TV/RGB

MODE

ANT

ባ

ቤ

ባ

EXIT

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

SELECT

VOL

ቤ

ባ

MUTE

VCR PLUS+

ቤ

ባ

LAST CH

UIDE/TV

VID 1

VID 5

4. The ANT button will act as the TV/STB button when in

STB mode.

VID 2

VID 4

FREEZE

VID 3

PIP

PIP CH

PIP ACCESS

SWAP

ቢ SET-TOP-BOX (STB) button

ቤ

VIDEO

PIP MODE

This button allows the remote to control your satellite receiv-

er by setting it to SET-TOP-BOX/SATELLITE mode.

ባ PRECODED SET-TOP-BOX/SATELLITE RECEIVER but-

REC

tons

These buttons transmit the chosen precoded set-top-

box/satellite codes.

CLU-5723TSI

ቤ EXCLUSIVE TV buttons

These buttons are for operating the TV.

MY SATELLITE RECEIVER/STB CODE IS:

NOTE:

Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-top-

box/satellite receiver.

ANT

TV/R

PECT

MUT

USING THE REMOTE TO CONTROL DVD FUNCTIONS

Operating the precoded function for your DVD player.

This remote is designed to operate different types of DVD players. You must first program the remote to match the remote command

set of your DVD player. (refer to page 39 for pre-codes)

1. Turn ON your DVD player.

2. Aim the remote control at the front of your DVD player.

3. Press and release the DVD button to switch to DVD pre-coded mode.

4. Hold down the DVD button on the remote and enter the two digit preset code that matches your DVD player, as shown on page 39.

The DVD button light will flash 3 times if the code was accepted.

5. Aim the remote at the DVD player and press the POWER button. The remote will turn off your DVD player if the correct two digit

preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn

off, try a different two digit preset code.

6. The remote will now control your DVD player.

7. You will need to set the Display Type of your DVD player to 16:9 Widescreen.

POWER

ባ

VCR

SOURCE WIZARD

CBL

NOTES:

STB

1. If your DVD player cannot be operated after performing

the above procedures, your DVD player’s code has not

been precoded into the remote.

2. In the unlikely event that your DVD player cannot be

operated after performing the above procedures, please

consult your DVD player operating guide.

TAPE

DVD

AMP

ቢ

ቤ

SLEEP

INFO

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

A/V NET

ASPECT

TV/RGB

MODE

ANT

EXIT

SELECT

ቤ

VOL

ቢ DVD Button

This button allows the remote to control your DVD player by

setting it to DVD mode.

MUTE

VCR PLUS+

LAST CH

UIDE/TV

VID 1

VID 5

VID 2

VID 4

FREEZE

VID 3

ባ PRECODED DVD Buttons

PIP

PIP CH

These buttons transmit the chosen precoded DVD codes.

ቤ

PIP ACCESS

SWAP

VIDEO

PIP MODE

ቤ EXCLUSIVE TV Buttons

These buttons are for operating the TV.

ባ

REC

CLU-5723TSI

MY DVD PLAYER CODE IS:

NOTE:

Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player.

ASPE

USING YOUR REMOTE

EXIT

ANT

MUTE

TO CONTROL ADDITIONAL AUDIO EQUIPMENT

Operating the precoded function for your Audio component.

This remote is designed to operate different types of Audio component. You must first program the remote to match the remote com-

mand set of your Audio component. (refer to page 39 for pre-codes)

1. Turn ON your Audio component you wish to control with the Remote.

2. Aim the remote control at the front of your Audio component.

3. Press and release the CD, TAPE, or AMP button to switch to Audio component pre-coded mode.

4. Hold down the CD, TAPE, or AMP button on the remote and enter the two digit preset code that matches your Audio component,

as shown on page 39. The CD, TAPE or AMP button light will flash 3 times if the code was accepted.

5. Aim the remote at the Audio component and press the POWER button. The remote will turn off your Audio component if the cor-

rect two digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio

component does not turn off, try a different two digit preset code.

6. The remote will now control your Audio component.

7. Repeat steps 1 - 6 if you wish to program the remote to control another Audio component. Be sure to use a different Audio button

on the remote, since only one component can be programmed per button.

POWER

ባ

NOTES:

VCR

SOURCE WIZARD

CBL

STB

1. If your Audio component cannot be operated after

performing the above procedures, your Audio

component’s code has not been precoded into the

remote.

2. In the unlikely event that your Audio component cannot be

operated after performing the above procedures, please

consult your Audio equipment operating guide.

TAPE

DVD

AMP

ቢ

ቤ

SLEEP

INFO

A/V NET

ASPECT

TV/RGB

MODE

ANT

3. The remote control will remember the codes you have

programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the

entire programming procedure as stated above.

EXIT

SELECT

ቤ

VOL

MUTE

VCR PLUS+

LAST CH

UIDE/TV

ቢ CD, TAPE, AMP Buttons

VID 2

ID 4

VID 3

These buttons allow the remote to control your Audio

equipment by setting it to Audio mode.

PIP

PIP CH

FREEZE

ቤ

PIP ACCESS

SWAP

VIDEO

PIP MODE

ባ PRECODED AUDIO Buttons

These buttons transmit the chosen precoded Audio

component codes.

ባ

REC

ቤ EXCLUSIVE TV Buttons

These buttons are for operating the Plasma TV.

CLU-5723TSI

MY AUDIO EQUIPMENT CODE IS:

TAPE

AMP/RCVR

NOTE:

Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment.

ANT

TV/R

AUDIO/VIDEO CODES

PECT

MUT

FOR REMOTE CONTROL ONLY

VCR BRAND. . . . . . . . . . . . . . . . . CODE

Adventura . . . . . . . . . . . . . . . . . . . . . . 01

Aiko. . . . . . . . . . . . . . . . . . . . . . . . . . . 09

Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . 01

Akai. . . . . . . . . . . . . . . . . . . . . 02, 47, 48

American High. . . . . . . . . . . . . . . . . . . 23

Asha . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Audiovox . . . . . . . . . . . . . . . . . . . . . . . 24

Beaumark . . . . . . . . . . . . . . . . . . . . . . 44

Bell & Howell. . . . . . . . . . . . . . . . . . . . 32

Broksonic. . . . . . . . . . . . . . . . . 33, 34, 41

Calix . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Canon . . . . . . . . . . . . . . . . . . . . . . . . . 23

Carver. . . . . . . . . . . . . . . . . . . . . . . . . 31

CCE . . . . . . . . . . . . . . . . . . . . . . . . . . 09

Citizen. . . . . . . . . . . . . . . . . . . . . . 09, 24

Craig . . . . . . . . . . . . . . . . . . . . 19, 24, 44

Curtis Mathes . . . . . . . . . . . . . 02, 23, 46

Cybernex. . . . . . . . . . . . . . . . . . . . . . . 44

Daewoo. . . . . . . . . . . . . . . . . . . . . 09, 17

Dynatech. . . . . . . . . . . . . . . . . . . . . . . 01

Electrohome . . . . . . . . . . . . . . . . . . . . 24

Electrophonic. . . . . . . . . . . . . . . . . . . . 24

Emerex . . . . . . . . . . . . . . . . . . . . . . . . 08

Emerson . . . . . . . . 01, 09, 13, 16, 24, 27,

. . . . . . . . . . . . . . . 28, 33, 34, 36, 41, 47

Fisher . . . . . . . . . . . . . . . . . . . 19, 21, 32

Fuji . . . . . . . . . . . . . . . . . . . . . . . . 10, 23

Funai. . . . . . . . . . . . . . . . . . . . . . . . . . 01

Garrard . . . . . . . . . . . . . . . . . . . . . . . . 01

GE. . . . . . . . . . . . . . . . . . . 04, 23, 40, 46

Goldstar. . . . . . . . . . . . . . . . . . 24, 25, 43

Gradiente . . . . . . . . . . . . . . . . . . . . . . 01

Harley Davidson . . . . . . . . . . . . . . . . . 01

Harmon/Kardon . . . . . . . . . . . . . . . . . . 25

Headquarter . . . . . . . . . . . . . . . . . . . . 18

Hi-Q . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Hitachi . . . . . . . . . . . . . 01, 02, 03, 04, 05

Jensen . . . . . . . . . . . . . . . . . . . . . . . . 02

JVC . . . . . . . . . . . . . . . . . . . . . 02, 14, 26

KEC . . . . . . . . . . . . . . . . . . . . . . . 09, 24

Kenwood . . . . . . . . . . . . . . . . . 02, 25, 26

KLH. . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Kodak . . . . . . . . . . . . . . . . . . . . . . 23, 24

Lloyd . . . . . . . . . . . . . . . . . . . . . . . . . . 01

Lloyd’s. . . . . . . . . . . . . . . . . . . . . . . . . 27

LXI . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Magnavox . . . . . . . . . . . . . 15, 23, 31, 35

Magnin . . . . . . . . . . . . . . . . . . . . . . . . 44

Marantz . . . . . . . . . . . . . . . . . . . . . 23, 31

Marta. . . . . . . . . . . . . . . . . . . . . . . . . . 24

Matsushita. . . . . . . . . . . . . . . . . . . . . . 23

MEI . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Memorex. . . . . . . . . . . . . . 01, 15, 18, 19,

. . . . . . . . . . . . . . . . . . 20, 23, 24, 32, 44

MGA . . . . . . . . . . . . . . . . . . . . . . . 16, 47

MGN Technology. . . . . . . . . . . . . . . . . 44

Minolta . . . . . . . . . . . . . . . . . . . . . 03, 05

Mitsubishi. . . . . . . . . . . 16, 26, 39, 47, 48

Motorola . . . . . . . . . . . . . . . . . . . . 20, 23

MTC . . . . . . . . . . . . . . . . . . . . . . . 01, 44

Multitech . . . . . . . . . . . . . . . . . . . . . . . 01

NEC. . . . . . . . . . . . . . . . . . 02, 25, 26, 32

Nikko. . . . . . . . . . . . . . . . . . . . . . . . . . 24

Noblex. . . . . . . . . . . . . . . . . . . . . . . . . 44

Olympus . . . . . . . . . . . . . . . . . . . . 12, 23

Optimus . . . . . . . . . . . . . . . . . 20, 24, 32

Panasonic . . . . . . . . . . . . . 11, 12, 23, 38

Penney . . . . . . . . . . . . 03, 23, 24, 25, 44

Pentax. . . . . . . . . . . . . . . . . . . 03, 04, 05

Philco . . . . . . . . . . . . . . . . . . . . . . . . . 23

Phillips. . . . . . . . . . . . . . . . . . . . . . 23, 31

Pilot. . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Pioneer . . . . . . . . . . . . . . . . . . . . . . . . 26

Pulsar . . . . . . . . . . . . . . . . . . . . . . . . . 15

Quarter . . . . . . . . . . . . . . . . . . . . . . . . 18

Quartz. . . . . . . . . . . . . . . . . . . . . . . . . 18

Quasar . . . . . . . . . . . . . . . . . . . . . . . . 23

Radio Shack . . . . . . . . . . . . . . . . . 01, 24

Radix. . . . . . . . . . . . . . . . . . . . . . . . . . 24

Randex . . . . . . . . . . . . . . . . . . . . . . . . 24

RCA. . . . . . . . . . . . 03, 04, 05, 35, 40, 46

Realistic . . . . . . . . . . . . . . 01, 18, 19, 20,

. . . . . . . . . . . . . . . . . . 21, 23, 24, 32, 44

Ricoh. . . . . . . . . . . . . . . . . . . . . . . . . . 22

Runco . . . . . . . . . . . . . . . . . . . . . . . . . 15

Samsung. . . . . . . . . . . . . . . . . . . . 17, 44

Sanky . . . . . . . . . . . . . . . . . . . . . . 15, 20

Sansui. . . . . . . . . . . . . . . . . . . . . . 02, 26

Sanyo . . . . . . . . . . . . . . . . 18, 19, 32, 44

Scott . . . . . . . . . . . 16, 17, 33, 34, 36, 41

Sears . . . . . . . . . . . . . . . . 03, 05, 18, 19,

. . . . . . . . . . . . . . . . . . . . . 21, 23, 24, 32

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . 20

Shintom. . . . . . . . . . . . . . . . . . . . . . . . 30

Shogun . . . . . . . . . . . . . . . . . . . . . . . . 44

Sony . . . . . . . . . . . . . . . . . 08, 10, 22, 23

STS. . . . . . . . . . . . . . . . . . . . . . . . . . . 03

Sylvania. . . . . . . . . . . . . . . 01, 16, 23, 31

Symphonic . . . . . . . . . . . . . . . . . . . . . 01

Tatung. . . . . . . . . . . . . . . . . . . . . . . . . 02

Teac . . . . . . . . . . . . . . . . . . . . . . . 01, 02

Technics . . . . . . . . . . . . . . . . . . . . 23, 38

Teknika . . . . . . . . . . . . . . . . . . 01, 23, 24

TMK . . . . . . . . . . . . . . . . . . . . . . . . 27,44

Toshiba . . . . . . . . . . . . . . . 16, 17, 21, 36

Totvision . . . . . . . . . . . . . . . . . . . . 24, 44

Unitech . . . . . . . . . . . . . . . . . . . . . . . . 44

Vector . . . . . . . . . . . . . . . . . . . . . . . . . 17

Vector Research . . . . . . . . . . . . . . . . . 25

Video Concepts . . . . . . . . . . . . . . . 17, 47

Videosonic. . . . . . . . . . . . . . . . . . . . . . 44

Wards . . . . . . . . . . . . . 01, 03, 19, 20, 23,

. . . . . . . . . . . . . . . . . . . . . 35, 36, 44, 46

XR-1000 . . . . . . . . . . . . . . . . . . . . 01, 23

Yamaha. . . . . . . . . . . . . . . . . . . . . . . . 25

Zenith . . . . . . . . . . . . . . . . . . . 10, 15, 22

Electricord . . . . . . . . . . . . . . . . . . . . . . 31

Everquest . . . . . . . . . . . . . . . . . . . . . . 51

Focus . . . . . . . . . . . . . . . . . . . . . . . . . 52

Garrard . . . . . . . . . . . . . . . . . . . . . . . . 11

GC Electronics. . . . . . . . . . . . . . . . 32, 39

Gemini. . . . . . . . . . . . . . . . 05, 38, 43, 51

General Instrument . . . . . . . . . . . . 01, 12

Goldstar. . . . . . . . . . . . . . . . . . . . . 10, 25

Hamlin . . . . . . . . . . . . . . . . 04, 13, 22, 23

Hitachi. . . . . . . . . . . . . . . . . . . . . . . . . 01

Hytex. . . . . . . . . . . . . . . . . . . . . . . . . . 36

Jasco. . . . . . . . . . . . . . . . . . . . . . . . . . 11

Jerrold . . . . . . . 01, 08, 12, 37, 49, 50, 51

Macom . . . . . . . . . . . . . . . . . . . . . . . . 35

Magnavox . . . . . . . . . . . . . . . . . . . . . . 15

Memorex. . . . . . . . . . . . . . . . . . . . . . . 03

Movie Time . . . . . . . . . . . . . . . 29, 31, 33

NSC . . . . . . . . . . . . . . . . . . . . 29, 33, 38

Oak . . . . . . . . . . . . . . . . . . . . . 21, 36, 46

Panasonic . . . . . . . . . . . . . . . . 02, 03, 09

Paragon . . . . . . . . . . . . . . . . . . . . . . . 03

Phillips . . . . . . . . . . . . . . . 11, 15, 16, 26,

. . . . . . . . . . . . . . . . . . . . . 30, 42, 43, 44

Pioneer . . . . . . . . . . . . . . . . . . 06, 10, 19

Popular Mechanics . . . . . . . . . . . . . . . 52

Pulsar . . . . . . . . . . . . . . . . . . . . . . . . . 03

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Realistic . . . . . . . . . . . . . . . . . . . . . . . 39

Recoton. . . . . . . . . . . . . . . . . . . . . . . . 52

Regal. . . . . . . . . . . . . . . . . . . . 04, 22, 34

Regency . . . . . . . . . . . . . . . . . . . . . . . 14

Rembrandt. . . . . . . . . . . . . . . . . . . 01, 38

Runco . . . . . . . . . . . . . . . . . . . . . . . . . 03

Samsung. . . . . . . . . . . . . . . . . . . . 10, 25

Scientific Atlanta. . . . . . . . . 17, 20, 41, 45

Signal . . . . . . . . . . . . . . . . . . . . . . 25, 51

Signature. . . . . . . . . . . . . . . . . . . . . . . 01

SL Marx. . . . . . . . . . . . . . . . . . . . . . . . 25

Sprucer . . . . . . . . . . . . . . . . . . . . . . . . 02

Starcom. . . . . . . . . . . . . . . . . . 37, 49, 51

Stargate. . . . . . . . . . . . . . . . . . . . . 25, 51

Starquest. . . . . . . . . . . . . . . . . . . . . . . 51

Starsight . . . . . . . . . . . . . . . . . . . . 53, 54

Sylvania . . . . . . . . . . . . . . . . . . . . . . . 18

Teleview . . . . . . . . . . . . . . . . . . . . . . . 25

Texscan. . . . . . . . . . . . . . . . . . . . . . . . 18

Tocom . . . . . . . . . . . . . . . . . . . 07, 27, 50

Toshiba . . . . . . . . . . . . . . . . . . . . . . . . 03

Tusa . . . . . . . . . . . . . . . . . . . . . . . . . . 51

TV 86 . . . . . . . . . . . . . . . . . . . . . . . . . 29

Unika. . . . . . . . . . . . . . . . . . . . . . . 11, 39

United Artists. . . . . . . . . . . . . . . . . . . . 36

United Cable . . . . . . . . . . . . . . . . . . . . 49

Universal . . . . . . . . 11, 24, 31, 32, 34, 39

Videoway . . . . . . . . . . . . . . . . . . . . . . 47

Viewstar. . . . . . . . . . . . . . . 15, 28, 29, 40

Zenith . . . . . . . . . . . . . . . . . . . . . . 03, 48

Zentek. . . . . . . . . . . . . . . . . . . . . . . . . 52

AMPLIFIER BRAND . . . . . . . . . . . CODE

Aiwa . . . . . . . . . . . . . . . . . . . . . . . 05, 06

Carver . . . . . . . . . . . . . . . . . . . 01, 06, 08

Denon . . . . . . . . . . . . . . . . . . . . . . . . . 10

Fisher . . . . . . . . . . . . . . . . . . . . . . 08, 11

Hitachi. . . . . . . . . . . . . . . . . . . . . . . . . 12

JVC. . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Kenwood . . . . . . . . . . . . . . 14, 15, 17, 18

Magnavox . . . . . . . . . . . . . . . . . . . 01, 06

Marantz . . . . . . . . . . . . . . . . . . 01, 06, 16

MCS . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Optimus . . . . . . . . . . . . 03, 04, 11, 15, 20

Panasonic . . . . . . . . . . . . . . . . . . . . . . 16

Philips . . . . . . . . . . . . . . . . . . . . . . 01, 06

Pioneer . . . . . . . . . . . . 03, 04, 20, 21, 22

Quasar . . . . . . . . . . . . . . . . . . . . . . . . 16

Sansui. . . . . . . . . . . . . . . . . . . . . . . . . 06

Sanyo . . . . . . . . . . . . . . . . . . . . . . . . . 11

Sharp . . . . . . . . . . . . . . . . . . . . . . . . . 15

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . 05

Technics. . . . . . . . . . . . 02, 16, 23, 24, 25

Victor. . . . . . . . . . . . . . . . . . . . . . . . . . 13

Wards . . . . . . . . . . 03, 05, 06, 08, 20, 21

Yamaha. . . . . . . . . . . . . . . . . . . . . 15, 26

CD BRAND. . . . . . . . . . . . . . . . . . CODE

Adcom. . . . . . . . . . . . . . . . . . . . . . . . . 01

Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . 02

California Audio Lab . . . . . . . . . . . . . . 03

Carver. . . . . . . . . . . . . . . . . . . . . . . . . 02

Denon . . . . . . . . . . . . . . . . . . . . . . . . . 04

DKK . . . . . . . . . . . . . . . . . . . . . . . . . . 05

Emerson . . . . . . . . . . . . . . . . . . . . . . . 01

Fisher . . . . . . . . . . . . . . . . . . . . . . . . . 06

Genexxa . . . . . . . . . . . . . . . . . . . . . . . 07

Hitachi . . . . . . . 01, 07, 08, 09, 10, 11, 12

JVC. . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Kenwood . . . . . . . . . . . . . . . . . 06, 14, 15

Krell . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Magnavox . . . . . . . . . . . . . . . . . . . . . . 02

Marantz . . . . . . . . . . . . . . . . . . . . . 02, 03

MCS . . . . . . . . . . . . . . . . . . . . . . . . . . 03

Mission . . . . . . . . . . . . . . . . . . . . . . . . 03

NSM . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Onkyo . . . . . . . . . . . . . . . . . . . . . . . . . 16

Optimus. . . . . . . . . . . . . . . . . . 05, 07, 17

Panasonic . . . . . . . . . . . . . . . . . . . . . . 03

Philips . . . . . . . . . . . . . . . . . . . . . . . . . 02

Pioneer . . . . . . . . . . . . . . . . . . . . . 07, 17

Proton . . . . . . . . . . . . . . . . . . . . . . . . . 02

QED . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Quasar . . . . . . . . . . . . . . . . . . . . . . . . 03

RCA . . . . . . . . . . . . . . . . . . . . . . . 01, 21

Realistic . . . . . . . . . . . . . . . . . . . . . . . 01

Rotel . . . . . . . . . . . . . . . . . . . . . . . . . . 02

SAE . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Sansui. . . . . . . . . . . . . . . . . . . . . . . . . 02

Scott . . . . . . . . . . . . . . . . . . . . . . . . . . 01

Sony . . . . . . . . . . . . . . . . . . . . . . . 05, 18

Technics . . . . . . . . . . . . . . . . . 03, 19, 20

Victor. . . . . . . . . . . . . . . . . . . . . . . . . . 13

DVD BRAND. . . . . . . . . . . . . . . . . CODE

Denon . . . . . . . . . . . . . . . . . . . . . . . . . 04

Hitachi . . . . . . . . . . . . . . . . . . . 07, 12, 13

JVC. . . . . . . . . . . . . . . . . . . . . . . . . . . 01

Kenwood. . . . . . . . . . . . . . . . . . . . . . . 04

Magnavox . . . . . . . . . . . . . . . . . . . . . . 05

Mitsubishi . . . . . . . . . . . . . . . . . . . . . . 10

Panasonic . . . . . . . . . . . . . . . . . . . . . . 04

Phillips . . . . . . . . . . . . . . . . . . . . . . . . 06

Pioneer . . . . . . . . . . . . . . . . . . . . . . . . 03

RCA (Proscan) . . . . . . . . . . . . . . . . . . 09

Samsung. . . . . . . . . . . . . . . . . . . . . . . 12

Sanyo . . . . . . . . . . . . . . . . . . . . . . . . . 13

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Toshiba . . . . . . . . . . . . . . . . . . . . . . . . 05

Yamaha. . . . . . . . . . . . . . . . . . . . . . . . 08

Zenith . . . . . . . . . . . . . . . . . . . . . . 05, 11

SATELLITE BRAND . . . . . . . . . . . CODE

Echostar . . . . . . . . . . . . . . . . . . . . . . . 04

Hitachi. . . . . . . . . . . . . . . . . . . . . . . . . 01

Hughes . . . . . . . . . . . . . . . . . . . . . . . . 05

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . 02

Sony . . . . . . . . . . . . . . . . . . . . . . . . . . 03

CABLE BRAND . . . . . . . . . . . . . . CODE

ABC . . . . . . . . . . . . . . . . . 01, 07, 08, 17,

. . . . . . . . . . . . . . . . . . 18, 20, 36, 37, 49

Antronix. . . . . . . . . . . . . . . . . . . . . . . . 39

Archer . . . . . . . . . . . . . . . . . . . 11, 24, 39

Belcor . . . . . . . . . . . . . . . . . . . . . . . . . 32

Cable Star. . . . . . . . . . . . . . . . . . . . . . 32

Century . . . . . . . . . . . . . . . . . . . . . . . . 11

Citizen . . . . . . . . . . . . . . . . . . . . . . . . . 11

Colour Voice . . . . . . . . . . . . . . . . . 30, 42

Comtronics . . . . . . . . . . . . . . . . . . 25, 28

Contec . . . . . . . . . . . . . . . . . . . . . . . . 21

Dae Ryung . . . . . . . . . . . . . . . . . . . . . 20

Eastern . . . . . . . . . . . . . . . . . . . . . . . . 14

TAPE BRAND. . . . . . . . . . . . . . . . CODE

Aiwa . . . . . . . . . . . . . . . . . . . . . . . 11, 12

Hitachi . . . . . . . . . . . . . . . . 01, 02, 03, 04

JVC. . . . . . . . . . . . . . . . . . . . . . . . . . . 05

Kenwood. . . . . . . . . . . . . . . . . . . . . . . 06

Optimus. . . . . . . . . . . . . . . . . . . . . . . . 07

Pioneer . . . . . . . . . . . . . . . . . . . . . . . . 07

Sony . . . . . . . . . . . . . . . . . 09, 10, 11, 12

Wards . . . . . . . . . . . . . . . . . . . . . . . . . 07

SET-TOP-BOX . . . . . . . . . . . . . . . CODE

Panasonic . . . . . . . . . . . . . . . . . . . . . . 06

RCA . . . . . . . . . . . . . . . . . . . . . . . . . . 07

Samsung. . . . . . . . . . . . . . . . . . . . . . . 08

OSD

1. Press MENU on the remote control to display the different features on your HITACHI Plasma TV.

2. Use the THUMB STICK to navigate to a different menu item.

3. Press EXIT on the remote control to quickly exit from a menu.

A/V Net

4. Press A/V NET on the remote control to access the A/V Network menu to control

external components.

SELECT

This part of the screen shows

which selections are available.

Video

Audio

Ch. Manager

Locks

Setup

SEL

Move

Sel

This part of the screen shows

which Remote Control buttons

to use.

OSD

Picture Mode

Select between the four picture modes; Sports, Movies, News,

and Music.

Contrast

Adjust contrast.

Brightness

Color

Adjust brightness.

Adjust color.

Tint

Adjust tint.

Adjust sharpness.

Centering top and bottom of the picture except HDTV signal.

Automatically change tint and color coordinates for DTV

program.

Video

Sharpness

Vertical Position

Color System

Advanced Settings

Improve picture performance.

Treble

Adjust the treble.

Bass

Adjust the bass.

Balance

Sound Enhancement

Advanced Settings

Adjust the balance.

Select TruBass and Matrix surround settings.

Improve sound performance.

Audio

Ant A

Ant B

View/edit Channel ID, Scan, and Lock settings in antenna A.

View/edit Channel ID, Scan, and Lock settings in antenna B.

Channel

Manager

Change Access Code

Engage Lock

TV Time Lock

Change Lock access code.

Choose to lock channel, video input, and front panel.

Set specific time to Lock TV.

Movie Ratings

Block various types of movies and video types based on motion

picture ratings.

TV Ratings

Block various types of movies and television programming

based on a parental guide ratings.

Lock

Canadian Ratings (ENG) Block various types of movies and television programming

based on the Canadian ratings system.

Canadian Ratings (FRN) Block various types of movies and television programming

based on the Canadian French ratings system.

Menu Preference

Screen Saver

Set the Clock

Set the Channels

Set the Inputs

Choose English, French, or Spanish text.

Set Screen Saver to prevent screen burn.

Set the TV clock. It must be set before using the Lock feature.

Set Channel Source and Auto Channel Scan.

Label Video Inputs , VCR, DVD, etc.

Setup

Set Event Timer

Set Closed Captions

Turn TV on and off once, daily, or weekly.

Feature to display dialogue/text.

VIDEO

Select VIDEO to adjust picture settings and improve picture quality.

Video

Picture Mode

Use this function to choose from automatic picture settings to optimize your TV’s performance.

Video

Audio

Ch. Manager

Locks

Setup

SEL

Move

Sel

THUMB

STICK

THUMB

STICK

SELECT

Video

Picture Mode

Contrast

Sports

100%

50%

Sports

Movies

News

Reset

Brightness

Color

THUMB

STICK

50%

Tint

SELECT

Music

Sharpness

50%

Vertical Position

Color System

Advanced Settings

SEL Select

Move

SEL Return

Move

Use THUMB STICK ̆ or ̄ to highlight Picture Mode settings.

When SPORTS mode is selected, the following are automatically set:

CONTRAST - 100%, COLOR TEMPERATURE - HIGH, BASS - 65%, TruBass - MEDIUM, PERFECT VOLUME - OFF,

MATRIX SURROUND - OFF, AUTO CONTRAST - OFF.

When MOVIES mode is selected, the following are automatically set:

CONTRAST - 59%, COLOR TEMPERATURE - MEDIUM, BASS - 65%, TruBass - MEDIUM, PERFECT VOLUME - OFF,

MATRIX SURROUND - OFF, AUTO CONTRAST - OFF, SHARPNESS - 50%.

NOTE:

MOVIE MODE 3:2 PULLDOWN DETECTION SPECIAL FEATURE

Theatrical movies are shot on film at 24 frames or still pictures per second, instead of 30 frames or 60 fields like video. When

film is transferred to video for television viewing, the disparity between the two frame rates must be reconciled. This involves

a process known as 3:2 pulldown.

When MOVIES mode is selected from the PICTURE MODE menu, your Hitachi Plasma Television will activate the circuitry

for this special feature to improve video performance when watching film based sources. This 3:2 pulldown detection will

only work in MOVIES mode.

When NEWS mode is selected, the following are automatically set:

CONTRAST - 75%, COLOR TEMPERATURE - MEDIUM, TruBass - MEDIUM, PERFECT VOLUME - ON, MATRIX SURROUND -

OFF,

AUTO CONTRAST - ON.

When MUSIC mode is selected, the following are automatically set:

CONTRAST - 75%, COLOR TEMPERATURE - HIGH, TruBass - MEDIUM, PERFECT VOLUME - OFF, MATRIX SURROUND - OFF,

AUTO CONTRAST - ON.

You can customize each of the above modes (SPORTS, MOVIES, NEWS and MUSIC) to your preference to increase viewing per-

formance and pleasure, depending upon the video program being viewed. If RESET is selected, only the selected mode will reset to the

initial conditions as explained above.

If RESET is selected in SPORTS mode, only SPORTS MODE will return to factory conditions.

Press EXIT to quit menu or select PICTURE MODE to return to previous menu.

VIDEO

Video

Picture Mode

Sports

100%

50%

Audio

Contrast

Ch. Manager

Locks

Brightness

Color

THUMB

STICK

THUMB

STICK

50%

Setup

Tint

SEL Sel

Move

SELECT

Sharpness

50%

Vertical Position

Color System

Advanced Settings

SEL Select

Move

Use the THUMB STICK ̆ or ̄ to highlight the function to be adjusted.

Press down on THUMB STICK to select the function settings.

Press the THUMB STICK ̇ or ̈ to adjust the function.

Press MENU to return to main menu.

Press EXIT to quit menu.

Use this function to change the contrast between black and white levels in the picture.

Contrast

Use this function to adjust overall picture brightness.

Use this function to adjust the level of color in the picture.

Brightness

Color

Tint

Use this function to adjust flesh tones so they appear natural.

Use this function to adjust the amount of fine detail in the picture.

Sharpness

Vertical Position

This function allows you to select when aspect style is either 4:3 EXPANDED/ZOOM1/ZOOM2. Vertical

position can be changed with these modes. For example, it will be useful for centering the picture area

at both the top and bottom of the picture with 480i/480P signal. Adjustable rage is -10 (video center is

toward bottom of screen) to +10 (video center is toward top of screen).

NOTES: 1. If CONTRAST is selected, you are adjusting CONTRAST. The additional menu items BRIGHTNESS, COLOR, TINT,

and SHARPNESS can be selected and adjusted in the same manner.

2. It may be necessary to adjust TINT to obtain optimum picture quality when using the COMPONENT VIDEO Y-P P

b r

input jacks.

3. If you are using the COMPONENT VIDEO input jacks (Y-P P ) and notice that the TINT and COLOR are abnormal,

b r

check to make sure that VIDEO - Color System is set properly.

Color System

This function allows you to automatically change tint and color coordinates for DTV programs.

AUTO - Automatically determines the color system for the input signal.

HDTV - High Definition Television - Use for High Definition Singal Y-P_bP_rfrom HDTV Set-Top Box.

SDTV/DVD - Standard Definition Television or DVD (Digital Versatile Disc Player) Y-C_bC_r.

NOTES: 1. If Color System is set improperly (does not match actual input signal), the color and tint of the main picture will be

abnormal.

2. All component color system settings will affect only color component input you are currently viewing. If you are using

both sets of component input jacks, be sure to set the color system feature for both inputs.

VIDEO

Your HITACHI Plasma TV has an ADVANCED SETTINGS function which will automatically adjust picture

settings to produce the highest quality picture possible.

When ADVANCED SETTINGS is highlighted, press down on THUMB STICK to access the ADVANCED

SETTINGS menu.

Advanced

Settings

Video

Picture Mode

Contrast

Sports

100%

50%

Brightness

Color

THUMB

STICK

50%

Tint

SELECT

Sharpness

50%

Vertical Position

Color System

Advanced Settings

SEL Select

Move

THUMB

STICK

SELECT

Video

Advanced Settings

Color Temperature

High

Color Temperature

High

Medium

Standard

Medium

Standard

THUMB

STICK

Auto Contrast

Noise Reduction

SELECT

Black Level Expansion

Black Side Panel

Black Level Expansion

Black Side Panel

SEL Return

SEL On/Off

Move

Use THUMB STICK to highlight functions.

Press down on THUMB STICK to select the function setting. When the function has an “✓” in the box, it is ON.

Press down on THUMB STICK to change COLOR TEMPERATURE setting. When the function shows a “ “, it is selected.

Press EXIT to quit the menu.

Color Temperature

Set this to High for cooler color with more blue (9,300K for 32HDT20, 9,200K for 42HDT20), set to Medium for more natural

color (7,500K), or set to Standard for accurate color (6,500K).

Auto Contrast

Turn on AUTO CONTRAST to improve picture detail in areas of high brightness.

Noise Reduction

The NOISE REDUCTION function automatically reduces conspicuous noise in the picture without degrading picture quality.

When NOISE REDUCTION is ON, SHARPNESS feature is disabled.

Black Level Expansion

The BLACK LEVEL EXPANSION function automatically enhances shadow detail in dark scenes.

Black Side Panel

The BLACK SIDE PANEL function turns the gray side bars on/off when watching 4:3 signals in Standard mode.

When the Plasma Television is powered OFF, BLACK SIDE PANEL feature will be set to OFF automatically when the TV is

powered ON. BLACK SIDE PANEL feature needs to be set every time the TV is turned ON.

The top/bottom gray bar will appear in SPLIT MODE PIP and SPLIT FREEZE.

NOTE:

To prevent screen burn when watching 4:3 signal, turn off the BLACK SIDE PANEL. It is

recommended to watch 4:3 signal with gray side bar.

AUDIO

Select AUDIO to adjust the TV to your preference and to improve the sound quality.

Audio

Video

Audio

Treble

50%

Audio

Bass

Ch. Manager

Locks

Balance

THUMB

STICK

THUMB

STICK

Sound Enhancement

Advanced Settings

Setup

SELECT

SEL

Move

Sel

SEL Select

Move

THUMB

STICK

Audio

Treble

Bass

50%

Balance

THUMB

STICK

Sound Enhancement

Advanced Settings

SELECT

SEL Select

Move

Treble

50%

SEL

Next/Prev

Change Value

Return

Press THUMB STICK to select menu item.

Press THUMB STICK ̇ or ̈ to adjust the function.

Press EXIT to quit the MENU, or select Audio to return to the main menu.

NOTE:

If TREBLE is selected you are adjusting treble. The additional menu items Bass and Balance can be selected and

adjusted in the same manner.

This function controls the high frequency audio to all speakers.

This function controls the low frequency audio to all speakers.

Treble

Bass

Balance

This function will control the left to right balance of the Plasma TV internal speakers.

AUDIO

The following surround settings will stimulate the “live” sound you would hear in concert halls, sports

stadiums, movie theaters, etc. with only two speakers.

Sound Enhancement

Audio

Treble

Bass

Audio

Sound Enhancement

50%

TruBass

Off

Low

Medium

High

Balance

THUMB

STICK

Sound Enhancement

Advanced Settings

SEL Select

Surround

Matrix Surround

SELECT

Move

SEL Return

Move

To enter SOUND ENHANCEMENT, use THUMB STICK ̆ or ̄ to highlight then press down on THUMB STICK to select SOUND

ENHANCEMENT of your choice.

Use the THUMB STICK to highlight your sound enhancement choice, and press SELECT to select your choice.

TruBass is an audio enhancement technology from SRS Labs that provides deep, rich bass on any speaker system without the need

for a subwoofer or additional extra physical components. For systems with a subwoofer, TruBass complements and enhances the

bass perfomance.

TruBass and the

symbol are trademarks of SRS Labs, Inc. TruBass technology is incorporated under license

NOTES:

from SRS Labs, Inc.

Matrix Surround

The Matrix Surround features the spacious sound effects of a stadium.

AUDIO

Advanced

Settings

Use ADVANCED SETTINGS to improve the sound performance of your TV, depending on listening conditions.

Audio

Treble

Audio

50%

Advanced Settings

Bass

Audio Source

Stereo

Mono

2nd Audio Prog.

Balance

THUMB

STICK

Sound Enhancement

Advanced Settings

Internal Speakers

Off

SELECT

SEL Select

Move

Auto Noise Cancel

Perfect Volume

SEL Return

Move

Press THUMB STICK ̆, ̄, ̇, ̈ to highlight a function. Press down on the THUMB STICK to select the function setting. When the

function has a “•” in the circle or a check (✓) in the box, it is ON.

Audio Source

Multi-Channel Television Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound) used when receiving

a weak stereo broadcast or 2nd Audio Prog (SAP) which may be a secondary language, weather report, etc.

The sources received will be displayed at the top left edge of the TV. The source you select will be displayed above the sources

received. See example below for each selection when both stereo and second audio are received (monaural is always received).

STEREO SELECTED

SAP SELECTED

ANT A 31

MONO SELECTED

MONO ANT A 31

ANT A 31

STEREO

ST/SA

SAP

ST/SA

NEWS

10:00 PM

NEWS

10:00 PM

Internal Speaker

This function is useful when setting up the external speakers. If you prefer to use only speakers from a separate stereo system, turn

this feature OFF. When set to OFF, the Plasma TV speakers and the sub-woofer output are OFF.

Auto Noise Cancel

This function eliminates the noise between stations. If a channel is tuned and is noisy, this function will automatically eliminate the audio

for that channel.

Perfect Volume

This function will automatically adjust volume so each channel and input has the same average volume level.

CHANNEL MANAGER

This function allows you to review which channels are labeled (CH ID), which have been added to Channel Memory

(SCAN), and which are protected by LOCK.

Channel

Manager

Ch. Manager

Ant A

Ant B

Move

Ant A

Ch#

Scan

ChID

Lock

Off

--------

SEL Select

THUMB

STICK

Off

SELECT

Off

SEL Return

Move

Press THUMB STICK ̆ or ̄ to review more channels.

Press EXIT to quit the menu.

Use this feature after Auto Channel Scan is completed to add (On) or erase (Off) additional channels to

the remote control channel ̆ or ̄ buttons.

Scan

Ch. Manager

Ant A

Ch#

Scan

Off

ChID

Lock

Ch#

Scan

Off

ChID

Lock

--------

[

]

THUMB

STICK

Off

SEL Return

̇/SEL

Return

Move

THUMB

STICK

Ch. Manager

Ant A

Ch. Manager

Ant A

Ch#

Scan

ChID

Lock

Ch#

Scan

ChID

Lock

[

]

[

Off

Set

--------

]

THUMB

STICK

--------

Off

Set

Move

To add (Scan-On) or erase (Scan-Off) additional channels while in Channel Manager, THUMB STICK ̇ to highlight the channel num-

ber, then THUMB STICK ̆ or ̄ to highlight other channels. Once the desired channel is highlghted, THUMB STICK ̈ to scan col-

umn, then THUMB STICK ̆ or ̄ to select ON or OFF.

NOTE:

Lock feature cannot be selected or set in CHANNEL MANAGER.

CHANNEL MANAGER

This section contains advanced features which will make TV viewing easier and more enjoyable. Use this

feature to give up to 20 channels a name when ANTENNA signal source is selected and up to 60 chan-

nels a name when CATV signal source is selected.

Channel ID

Channel Manager

Ant A

Ch#

Scan

ChID

Lock

Ch#

Scan

ChID

Lock

[

]

[

]

--------

A-------

--------

THUMB

STICK

THUMB

STICK

Off

Edit (A-Z, 0-9, _, -)

SEL Return

Move

Edit (A-Z, 0-9, _, -)

SEL Return

Move

THUMB

STICK

Channel Manager

Ant A

Ch#

Scan

ChID

Lock

A-------

--------

[

]

Off

Move

Edit (A-Z, 0-9, _, -)

SEL Return

NOTES: 1. If ANT A and ANT B are in the same ANTENNA/CABLE mode, the CHANNEL ID for both antenna inputs will be the

same.

2. CHANNEL ID will be displayed only when channel is displayed as main picture.

LOCKS

This function will block out the picture and sound of the selected channel or video input.

It can also be used to keep the TV from being viewed for a scheduled time period that you set.

Locks

The code to enter the Locks feature is a four digit secret code number. The factory preset code is 0000.

Use the number buttons to select secret code.

Video

Locks

Audio

Ch. Manager

Locks

Please Enter Access Code

THUMB

STICK

Setup

[ - - - - ]

SEL

Move

Sel

SELECT

[# Keys] Enter Secret Code

Locks

Change Access Code

Engage Lock

TV Time Out

Movie Rating

TV Rating

Canadian Ratings (Eng)

Canadian Ratings (Frn)

SEL Return

Move

Use THUMB STICK ̆ or ̄ to highlight function and then press SELECT button.

To change the secret code number, select Change Access Code. Enter a new four digit key number you prefer.

Select CHANGE ACCESS CODE to change the factory preset code (0000) to your preference.

When ENGAGE LOCK is selected, SET CHANNEL LOCK, SET INPUT LOCK, and SET FRONT PANEL LOCK can be set individually.

When SET CHANNEL LOCK is turned on, the picture and sound for the chosen channel will be blocked out.

When SET INPUT LOCK is turned on, the picture and sound for all video inputs and the picture and sound for channels 3, 4 will be

blocked out.

When FRONT PANEL LOCK is turned on, all buttons on the Front Panel will be deactivated, except the Power button.

When TV TIME OUT is turned on (✓ TIME LOCK) you can set the BEGIN and END times (THUMB STICK ̈) and the TV

✓

cannot be viewed during that time period (Set clock first). Use CURSOR ̆ or ̄ to highlight ONCE (TV will time out one time

only), DAILY (TV will time out every day), WEEKLY (TV will time out one time a week).

When MOVIE RATINGS is selected, you can block various types of movies and video tapes based on motion picture ratings. Picture-

in-Picture will also be blocked automatically (see page 51).

When TV RATINGS is selected, various types of television programming based on a parental guide ratings will be blocked.

Picture-in-Picture will also be blocked automatically (see page 52).

Use CANADIAN RATINGS to block various types of movies and television programs based on the two rating systems used in

Canada that you feel may be inappropriate due to its content (see pages 53-54).

If you forget your secret code, use the factory code 7777 to erase your key number. This will reset the secret code number back to the

factory preset 0000.

Press EXIT to quit the menu.

NOTE:

1. If ANT A and ANT B are in the same signal source mode (see page 58), when a channel is locked, it is locked

on both antenna inputs.

2. When using TIME LOCK make sure the clock is set (see page 57).

3. Text appears on the screen to indicate that TV TIMED LOCK is activated.

4. If MOVIE/TV Ratings Lock function settings are ON, PIP SURF mode wil be deactivated.

LOCKS

Use MOVIE RATINGS to prevent viewing of any movie that you feel may be inappropriate due to

its content.

Movie Ratings

Locks

Change Access Code

Locks

Movie Ratings

Engage Lock

Status

Not Rated:

TV Time Lock

THUMB

STICK

THUMB

STICK

PG:

Movie Ratings

TV Ratings

SELECT

Canadian Ratings (Eng)

Canadian Ratings (Frn)

PG-13:

SEL Select

Move

NC-17:

SEL Return

Move

Use THUMB STICK ̆ or ̄ to select the MOVIE RATING category that you want to block.

Press SELECT to block the MOVIE RATING that you have selected. Once rating is selected, for example PG-13, all

movies rated PG-13 and higher (R, NC-17, and X) will be blocked.

Press EXIT to quit the menu or select MOVIE RATING to return to the previous menu.

Motion Picture Ratings Chart

General audiences. All ages admit-

ted.

Parental guidance suggested.

Some material may not be suitable

for children.

Parents strongly cautioned. Some

material may be inappropriate for

children under 13.

PG-13

Restricted. Under 17 requires

accompanying parent or adult

guardian.

No one 17 and under admitted.

NC-17

Adults only

Contains no rating. Not Rated

(NR) and Not Applicable (NA) pro-

grams. Movie has not been rated or

ratings do not apply.

NOT RATED (NR)

LOCKS

Use TV RATINGS to prevent the viewing of any TV program that you feel may be inappropriate

due to its content.

TV Ratings

Locks

Change Access Code

Locks

TV Rating

Engage Lock

Sub Category

TV Time Lock

Status

TV-Y:

THUMB

STICK

THUMB

STICK

Movie Ratings

TV Ratings

TV-7:

TV-G:

SELECT

Canadian Ratings (Eng)

Canadian Ratings (Frn)

TV-PG:

TV-14:

TV-MA:

SEL Select

Move

SEL Return

Move

Use THUMB STICK ̆ or ̄ to highlight the category that you want to block.

Press select to block the TV RATINGS that you have selected.

Press EXIT to quit the menu or select TV RATINGS to return to the previous menu.

TV Parental Guide Ratings Chart

NOTE:

None.

N/A

If you Block TV-14D, you will still permit

TV MA programs; If you block TV-14DV,

you will automatically block TV-MAV

programs, but you will still permit TV-

MALS programs. This means that the

TV will block violence in TV-14 and

higher (TV-MA), but not language and

sex.

All children. The themes and elements in this

program are specifically designed for a very

young audience, including children from ages

2-6.

TV-Y

Directed to older children. Themes and ele-

ments in this program may include mild physi-

cal or comedic violence, or may frighten chil-

dren under the age of 7.

TV-Y7

TV-G

General audience. It contains little or no vio-

lence, no strong language, and little or no sex-

ual dialogue or situations.

Parental guidance suggested. The program

may contain infrequent coarse language, limit-

ed violence, some suggestive sexual dialogue

and situations.

TV-PG

Parents strongly cautioned. This program

may contain sophisticated themes, intense

sexual situation, more intense violence and

intensely suggestive dialogue.

TV-14

Mature audiences only. This program may

contain mature themes, indecent language,

graphic violence, and explicit sexual content.

TV-MA

Fantasy Violence

Violence

Sexual Situation

Adult Language

Sexually Suggestive Dialogue.

LOCKS

Use Canadian Ratings (Eng) to block various types of movies and television programs used in

Canada that you feel may be inappropriate due to its content.

Canadian Ratings

(Eng)

Locks

Change Access Code

Locks

Canadian Ratings (Eng)

Status

Engage Lock

TV Time Lock

Movie Ratings

TV Ratings

THUMB

STICK

THUMB

STICK

C8+:

SELECT

Canadian Ratings (Eng)

PG:

Canadian Ratings (Frn)

14+:

18+:

SEL Select

Move

SEL Return

Move

Use THUMB STICK ̆ or ̄ to select the CANADIAN RATINGS (Eng) category that you want to block.

Press SELECT to set the CANADIAN RATINGS (Eng) that you have selected.

Once rating is selected, for example C8+, all movies and television programs rated C8+ and higher (G, PG, 14+ and

18+) will be blocked automatically.

Press EXIT to quit the menu.

Canadian Ratings English Chart

Programming intended for children under age 8 - Violence Guidelines; Careful

attention is paid to themes, which could threaten children’s sense of security and well-

being. There will be no realistic scenes of violence. Depictions of aggressive behav-

iour will be infrequent and limited to portrayals that are clearly imaginary, comedic or

unrealistic in nature. Other Content Guidelines: There will be no offensive language,

nudity or sexual content.

Programming generally considered acceptable for children 8 years and over to

watch on their own - Violence Guidelines: Violence will not be portrayed as the pre-

ferred, acceptable, or only way to resolve conflict; or encourage children to imitate dan-

gerous acts which they may see on television. Any realistic depictions of violence will

C8+

be infrequent, discreet, of low intensity and will show the consequences of the acts.

Other Content Guidelines: There will be no profanity, nudity or sexual content.

General Audience - Violence Guidelines: Will contain very little violence, either physi-

cal or verbal or emotional. Will be sensitive to themes which could frighten a younger

child, will not depict realistic scenes of violence which minimize or gloss over the

effects of violent acts. Other Content Guidelines: There may be some inoffensive

slang, no profanity and no nudity.

Parental Guidance - Programming intended for a general audience but which may not

be suitable for younger children. Parents may consider some content inappropriate for

unsupervised viewing by children ages 8-13. Violence Guidelines: Depictions of con-

flict and/or aggression will be limited and moderate; may include physical, fantasy, or

supernatural violence. Other Content Guidelines: May contain infrequent mild profani-

ty, or mildly suggestive language. Could also contain brief scenes of nudity.

Programming contains themes or content which may not be suitable for viewers

under the age of 14 - Parents are strongly cautioned to exercise discretion in permit-

ting viewing by pre-teens and early teens. Violence Guidelines: May contain intense

14+

scenes of violence. Could deal with mature themes and societal issues in a realistic

fashion. Other Content Guidelines: May contain scenes of nudity and/or sexual activity.

There could be frequent use of profanity.

Adult - Violence Guidelines: May contain violence integral to the development of the

plot, character or theme, intended for adult audiences. Other Content Guidlines: May

contain graphic language and explicit portrayals of nudity and/or sex.

18+

LOCKS

Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various pro-

gram ratings that you feel may be inappropriate due to its content.

Canadian Ratings

(Frn)

Locks

Change Access Code

Locks

Canadian Ratings (Frn)

Status

Engage Lock

TV Time Lock

THUMB

STICK

THUMB

STICK

8 ans+:

13 ans+:

16 ans+:

18 ans+:

Movie Ratings

TV Ratings

SELECT

Canadian Ratings (Eng)

Canadian Ratings (FRN)

SEL Select

Move

SEL Return

Move

Use THUMB STICK ̆ or ̄ to highlight the category that you want to block.

Press SELECT to set the CANADIAN RATINGS (FRN) that you have selected.

Once rating is selected, for example 8 ans+, all movies and television programs rated 8 ans+ and higher (13 ans+, 16

ans+, 18 ans+) will be automatically blocked.

Press EXIT to quit the menu.

Canadian Ratings French Chart

General - Programming intended for audiences

of all ages. Contains no violence, or the vio-

lence content is minimal or is depicted appropri-

ately with humor or caricature or in an unrealis-

tic manner.

8 + General - Not recommended for young

children - Programming intended for a broad

audience but contains light or occasional

violence that could disturb young children.

Viewing with an adult is therefore recommended

8 ans +

for young children (under the age of 8) who can-

not differentiate between real and imaginary

portrayals.

Programming may not be suitable for chil-

dren under the age of 13 - Contains either a

few violent scenes or one or more sufficiently

13 ans +

violent scenes to affect them. Viewing with an

adult is therefore strongly recommended for

children under 13.

Programming is not suitable for children

under the age of 16 - Contains frequent scenes

of violence or intense violence.

16 ans +

Programming restricted to adults - Contains

constant violence or scenes of extreme violence.

18 ans +

SETUP

Select SETUP when setting up your TV for the first time. Use the THUMB STICK ̆ or ̄ on the remote to highlight

the function desired.

Setup

Video

Setup

Menu Preference

Audio

Screen Saver

Ch. Manager

Locks

Set The Clock

THUMB

STICK

THUMB

STICK

Set The Channels

Set The Inputs

Set Event Timer

Set Closed Captions

Setup

SELECT

SEL

Move

Sel

SEL Return

Move

Use THUMB STICK ̆ or ̄ to select the sub-menu of your choice.

Menu Preference

This feature will allow you to select any one of three different languages for all on-screen displays.

Setup

Menu Preference

Setup

Menu Preferences

Screen Saver

Set The Language

English

Français

Español

Set The Clock

THUMB

STICK

THUMB

STICK

Set The Channels

Set The Inputs

Set Event Timer

Set Closed Captions

Set The Menu Background

Shaded

Solid

SELECT

SEL Select

Move

SEL Return

Move

THUMB

STICK

Setup

Menu Preferences

Set The Language

English

Français

Español

Set The Menu Background

Shaded

Solid

SEL Select

Move

Use THUMB STICK ̇ , ̈ to highlight the language of your choice.

Press SELECT to select the highlighted language.

Press EXIT to quit the menu.

SETUP

Menu Preference

This function allows you to choose from two menu backgrounds.

Setup

Menu Preferences

Set The Language

English

French

Spanish

THUMB

STICK

Set The Menu Background

Shaded Solid

SEL Select

Move

Use THUMB STICK ̇ , ̈ to highlight SET THE MENU BACKGROUND (shaded or solid), and press down on THUMB STICK to select

the setting.

Press EXIT to quit the menu.

Select SOLID and SHADED background is visible (no picture can be seen behind menu screen), select SHADED and a light background

is visible.

Continuous on-screen displays such as video games, stock market quotations, computer generated graphics,

and other fixed (non-moving) patterns can cause permanent damage to Plasma Television. Use the SCREEN

SAVER feature to hide screen burn.

Screen

Saver

Setup

Menu Preference

Setup

Screen Saver

Main Picture Moving

Off

Set The Clock

THUMB

STICK

THUMB

STICK

Set The Channels

Set The Inputs

Option 1

Option 2

Option 3

SELECT

Set Event Timer

Set Closed Captions

Screen Wipe

Wipe

SEL Select

Move

SEL Select

Move

Use THUMB STICK ̆ , ̄ to highlight Screen Saver’s Main Picture Moving options.

Press down on THUMB STICK to select and EXIT to quit.

Option 1

The whole picture will shift every 20 minutes by two pixels.

Option 2

The whole picture will shift every 40 minutes by two pixels.

Option 3

The whole picture will shift every 60 minutes by two pixels.

Screen Wipe

If pattern mark occurs, use Screen Wipe (White Field Signal) for at least 10 minutes to refresh any damage that may have occured from

a pattern mark. Screen Wipe can resolve pattern mark to a certain degree, if caution is not used, permanent damage may occur. Press

the EXIT button to return to normal viewing.

Screen Saver Picture’s Movement

SETUP

The time must be set before you can Set Event Timer or TV Time Out.

Set The Clock

Setup

Menu Preference

Screen Saver

Setup

Set The Clock

Set The Channels

Set The Inputs

THUMB

STICK

Time : Sun --:-- AM

SELECT

Set Event Timer

Set Closed Captions

SEL Select

Move

SEL Return

Move

THUMB

STICK

Setup

Set The Clock

Time : Sun --:-- AM

SEL Return

Move

Set

Use THUMB STICK ̆ or ̄ to set the time, and date.

Press THUMB STICK ̇ or ̈ to change position.

Press EXIT to quit the menu.

SETUP

Set The Channels

Select ANTENNA if you are using an indoor or outdoor antenna. Select Cable if you have cable TV.

Setup

Set The Channels

Menu Preference

Screen Saver

Set The Clock

Ant A

Ant B

THUMB

STICK

Set The Channels

Set The Inputs

SEL Return

Move

SELECT

Set Event Timer

Set Closed Captions

SEL Select

Move

THUMB

STICK

Setup

Set The Channels

Ant A

Source

Antenna

THUMB

STICK

Ant B

Cable(1)

Cable(2)

Start

SEL Select

Move

Auto Channel Scan

SELECT

SEL Return

Move

THUMB

STICK

Setup

Set The Channels

Ant A

Source

Antenna

NOTE:

Cable(1)

Cable(2)

Start

Auto Channel Scan

If certain CATV channels are poor or not possible in

Cable(1) mode, select Cable(2).

SEL Select

Move

Use THUMB STICK ̇ , ̈ to highlight the correct signal mode.

Press the THUMB STICK to select highlighted signal.

Press EXIT to quit the MENU.

RECEPTION BAND

CATV 1 OR CATV 2

Reception channels for each mode are shown at the left.

CATV CHANNEL

Indicated on

AIR

the screen

2 ~ 13

Refer to your cable or TV guide for channel identification standards.

VHF 2~13

14 ~ 22

95 ~ 99

23 ~ 36

37 ~ 64

Mid band A~1

A-5 ~ A-1

VHF 2 ~ 13ch

UHF 14 ~ 69ch

Super band J~W

Hyper band

W + 1 ~ W + 28

65 ~ 125

Ultraband

W + 29 ~ W + 84

SETUP

This feature will automatically store active TV channels in Auto Channel Scan. This will allow you to skip

unused channels when using CHANNEL UP (̆) or DOWN (̄).

Auto Channel Scan

Setup

Set The Channels

Ant A

Source

Setup

Set The Channels

Ant A

Source

Antenna

THUMB

STICK

Antenna

Cable(1)

Cable(2)

Start

Cable(1)

Cable(2)

Auto Channel Scan

Start

SEL Select

Move

THUMB

STICK

SELECT

Setup

Set The Channels

Ant A

Auto Channel Scan

Scanning Channel Number: 66

Cancel

SEL Cancel

Move

If the EXIT button is pressed while AUTO CHANNEL SCAN function is engaged, programming will stop. If two antennas are

connected, switch antenna inputs and repeat AUTO CHANNEL SCAN for the second antenna input.

Remember to select the correct ANTENNA/CABLE mode before using AUTO CHANNEL SCAN.

See CHANNEL MANAGER - SCAN to add or to erase additional channels.

SETUP

Use this feature to give a name to any of the five video inputs.

Set The Inputs

Setup

Set The Inputs

Menu Preference

Screen Saver

Video 1 Rename

Video 2 Rename

Video 2 Auto Link

Video 3 Rename

Video 4 Rename

Video 5 Rename

Video Power Save

Set The Clock

THUMB

STICK

Set The Channels

Set The Inputs

SELECT

Set Event Timer

Set Closed Captions

SEL Select

Move

SEL Return

Move

THUMB

STICK

Setup

Set The Inputs

Video 1 Rename

Video 2 Rename

Video 2 Auto Link

Video 3 Rename

Video 4 Rename

Video 5 Rename

Video Power Save

List

THUMB

STICK

CAM

CBL

DVD

DVD1

DVD2

VCR

VCR1

VCR2

Reset

SELECT

SAT

STB

SEL Select

Move

SEL Return

Move

Press THUMB STICK ̆, ̄ to highlight the name of the video inputs.

Press down on THUMB STICK to select desired input name.

Select RESET to set video names to original factory preset condition.

NOTE:

The video input name will be displayed only when video input is displayed as main picture.

Use this feature to reduce power consumption for video input. In RGB mode, this feature will always be on.

Video Power Save

Setup

Set The Inputs

Video 1 Rename

Video 2 Rename

Video 2 Auto Link

Video 3 Rename

Video 4 Rename

Video 5 Rename

Video Power Save

THUMB

STICK

Power Save For Video Input

SELECT

SEL Select

SEL Return

Move

Press THUMB STICK ̄ to highlight POWER SAVE FOR VIDEO INPUT.

Press down on THUMB STICK to select.

SETUP

Use this function to automatically turn the TV on and tune to Video 2 when it detects a video signal to

input 2.

Video 2 Auto Link

Setup

Set The Inputs

Video 2 Auto Link

Video 1 Rename

Video 2 Rename

Video 2 Auto Link

Video 3 Rename

Video 4 Rename

Video 5 Rename

Video Power Save

THUMB

Auto Input Signal Sensor

Remote Control Sensor

Off

STICK

SELECT

SEL Select

Move

SEL Return

Move

THUMB

STICK

Setup

Set The Inputs

Video 2 Auto Link

Auto Input Signal Sensor

Remote Control Sensor

Off

SEL Select

Move

Use THUMB STICK ̆ or ̄, then press down on THUMB STICK to change AUTO LINK setting.

When AUTO INPUT SIGNAL SENSOR is selected, the TV will turn on and switch to Video2 automatically, when the Video2 input device

is turned on. This is convenient when you want to watch a movie with your VCR, laserdisc player, or DVD player.

When REMOTE CONTROL SENSOR is selected, the TV will turn on and switch to Video2 automatically when the Video2 input device

is turned on (VCR, laserdisc, or DVD) and any of the buttons on your remote control is pressed.

Select Off to disable this function.

Press EXIT to quit the menu.

NOTES: 1. Once the TV has been turned on using the AUTO LINK feature, it must be reset before AUTO LINK is used again. To

do this, turn your VCR, laserdisc, or DVD player OFF. This feature is now reset and will turn on your TV as described

above.

2. When using REMOTE CONTROL SENSOR mode, any remote control button will substitute for your video input device

play button. However, intended operation is for use with your VCR, laserdisc, or DVD play button.

3. If no remote control button is pressed after the TV is turned on by AUTO LINK, the TV will automatically turn off after

three hours.

SETUP

This function will automatically turn the Plasma TV on and off, one time only, every day, or once a

week.

Set Event Timer

If the clock is not set (see page 57), you can not use this function and the screen below will appear.

Please Set The Clock First.

Setup

Menu Preference

Setup

Set Event Timer

Screen Saver

Event 1

Ant A

--:-- AM

Ch --

--:-- AM

Once

--:-- AM

Once

--:-- AM

Once

Set The Clock

THUMB

STICK

Set The Channels

Set The Inputs

Set Event Timer

Set Closed Captions

Event 2

Ant A

--:-- AM

Ch --

SELECT

Event 3

Ant A

--:-- AM

Ch --

SEL Select

Move

SEL Return

Move

THUMB

STICK

Setup

Set Event Timer

Event 1

Ant A

--:-- AM

Once

--:-- AM

Once

--:-- AM

Once

Ch --

Event 2

Ant A

--:-- AM

Ch --

Event 3

Ant A

--:-- AM

Ch --

SEL On/Off

Return

Move

Use THUMB STICK ̄ to select Event 1, 2 or 3.

Use THUMB STICK ̈ to change position of On time, Off time, Antenna, Channel, and On/Off Frequency.

Use THUMB STICK ̆ or ̄ to select the time the TV will turn on and off.

Use THUMB STICK ̆ or ̄ to select the day of the week you want the timer to turn on TV.

Use number buttons to set the channel the TV will tune to when it automatically turns on.

Use THUMB STICK ̆ or ̄ to select mode Once (TV will turn on/off one time only), Daily (TV will turn on/off at the same time every

day), or Weekly-Sun (TV will turn on/off at same time every week).

Press EXIT to quit the menu.

CAUTION: Do not use your TV as a deterrent when away from home by using the On and Off Timers. For safety, the TV

should be turned off when you are away from home.

SETUP

Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video

which are displayed on the Plasma Television screen. Your local TV program guide denotes these programs

Closed Caption

Setup

Set Closed Caption

Caption Display

Menu Preference

Screen Saver

Off

Auto

Text

Set The Clock

THUMB

STICK

Set The Channels

Set The Inputs

Set Event Timer

Set Closed Captions

Captions

Mode:

Channel:

Captions

SELECT

SEL Select

Move

SEL Return

Move

Caption Display:

On/Off will turn the

display on or off.

display on when Mute/Soft Mute is on.

Auto will turn the

Captions Mode:

Captions is for the program you are viewing.

Text is for additional information such as news reports or a TV program guide. This information covers the entire

screen and viewing the TV program is not possible. Text may not be available with every program.

Captions Channel: 1 is used for the primary language (usually English).

2 is sometimes used for a second language (may vary by region).

3 is sometimes used for a third language (may vary by region).

4 is sometimes used for a fourth language (may vary by region).

Use THUMB STICK ̆, ̄ to highlight the function to change then press THUMB STICK to change the function.

Press EXIT to quit menu or THUMB STICK ̇ to return to previous menu.

NOTE:

1. CAPTION DISPLAY will not work when viewing a 480P, 720P, or 1080i input via the COMPONENT: Y-P P inputs.

B R

2. When PIP Surf Modeis on, Closed Caption will not work.

RGB ON SCREEN DISPLAY

IMPORTANT: TURN OFF THE AVC BOX, THE DISPLAY MONITOR AND THE EXTERNAL COMPONENT BEFORE

CONNECTING OR DISCONNECTING ANY CABLES.

1. AVC rear panel connection to an exernal component with an analog RGB output.

RGB ANALOG

OUTPUT

15 14 13 12 11

AUDIO OUT

SET-TOP-BOX

D-SUB 15 Pin

RGB Cable

(Optional)

Audio Cable

(Optional)

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

AUDIO

(MONO)

BLASTER

AUDIO

ANT B

AUDIO

AUDIO OUT

2. AVC rear panel connection to an external component with a digital RGB2 output.

RGB DIGITAL

OUTPUT

AUDIO OUT

SET-TOP-BOX

DIgital Link

Cable (Optional)

Audio Cable

(Optional)

ANT A

RGB 1

RGB 2

TO MONITOR

MONITOR

OUT

S-VIDEO

INPUT 4

S-VIDEO

INPUT 3

S-VIDEO

ANALOG INPUT

DIGITAL INPUT

CONVERTER

AUDIO

VIDEO

INPUT 2

INPUT 1

AUDIO

Y/VIDEO

AUDIO

BLASTER

(MONO)

AUDIO

ANT B

AUDIO

AUDIO OUT

RGB ON SCREEN DISPLAY

This Plasma Television can automatically detect and display the signal format below.

1. RGB input signal.

This Plasma Television can accept the following signal formats.

Recommended Signal List

Signal Mode

Vertical

Frequency (Hz)

Horizontal

Frequency (kHz)

No.

Signal Name

VGA

Resolution

640 x400

640 x 480

800 x 600

1024 x 768

1280 x 1024

1080

70.10

59.94

72.81

75.00

56.25

60.32

72.19

75.00

60.00

70.07

75.03

60.02

75.03

59.94

31.48

31.47

37.86

37.50

35.16

37.88

48.08

46.88

48.36

56.48

60.02

63.98

79.98

33.72

44.96

31.47

VESA

1080i

720p

480p

720

480

NOTE: 1. Dots correspond to the true resolution in Real Mode of aspect ratio, when you select VGA signal from the table above.

(One dot corresponds to one pixel).

2. Always reset AUTO ADJUST feature when setting new display setting or when changing to a new computer

(see page 29).

RGB ON SCREEN DISPLAY

2. The new setting (horizontal position, vertical position, clock, and phase) of the signal will be stored. The monitor can store up to 13

settings in addition to the 10 pre-set signal timing. Any additional new settings (more than 10) will over-write the first user’s setting,

second setting and so on.

3. Operation in RGB mode in relation to TV functions are shown below.

No. Item

Operation

Event Timer

Only power on is available

Video Control

Contrast and brightness work separately, however, other picture controls

are not available.

A/V Net

Not available.

Audio Settings

Mute / Soft Mute

Closed Caption

Clock

Not available.

Available.

Not available.

Clock indication is not available.

When SLEEP timer is set in TV mode, remaining indication is shown.

Both picture and audio are not available.

Not available.

Sleep Timer

Monitor Out

10 Lock

11 Front Panel Lock

12 Menu Language

13 Auto Link

Available.

Only English is available.

Turn on to TV mode.

14 Menu Background

Not available.

RGB ON SCREEN DISPLAY

4. Other signal formats may not be displayed correctly. Use AUTO ADJUST to automatically adjust the horizontal position, vertical posi-

tion, clock, and phase. We recommend you use a signal, which has more than 50% of amplitude of white area at each corner of

the picture, when performing Auto Adjustment. It may not work correctly with dark picture. (See page 72-73).

5. Input signal level.

SYNC

TTL level H/V separate signal

RGB INPUT 0.7Vpp

NOTE:

Interlaced signal is not available.

6. RGB input signal will not appear at all when receiving a signal which is not supported by this product. If the setting is wrong, the

Display Monitor will display:

NO SYNC. SIGNAL

INVALID SCAN FREQ.

Without sync

Either horizontal or vertical

frequency is inappropriate

or out of range.

NOTE: 1. If the Display Monitor cannot display a signal, please try AUTO ADJUST to display the signal. This is used to initialize

the MultiScan Converter.

2. Not all signals have AUTO ADJUST feature (see page 29).

3. Set-Top-Box and DVD player input signal does not have AUTO ADJUST feature.

RGB ON SCREEN DISPLAY

1. Press TV/RGB button on the remote control to switch between TV, RGB1, and RGB2 modes.

2. Press MENU on the remote control to display the different features in RGB MODE.

3. Press the THUMB STICK ̆, ̄, ̇, ̈ buttons to highlight a different feature.

4. Press EXIT on the remote control to quickly exit from a menu.

TV/RGB

SELECT

RGB MODE MENU

VIDEO

This part of the screen shows

SETUP

which Remote Control buttons

to use.

EXIT

SEL

TO QUIT

MOVE

TO SELECT

RGB ON SCREEN DISPLAY

CONTRAST

Change the contrast between black and white levels in the

picture.

BRIGHTNESS

COLOR

TEMPERATURE

ENHANCER

Adjust overall picture brightness.

VIDEO

Select between HIGH (9,300K-32HDT20, 9,200K-42HDT20),

MEDIUM (7,500K) or STANDARD (6,500K).

Enhance picture details.

RESET

BLACK SIDE PANEL

Recall the factory preset data of the RGB Video Settings.

Turns the gray side bars ON/OFF when watching 4:3 signals in

standard mode.

RGB:1 Analog Input Mode Menu

AUTO ADJUST

H. POSITION

V. POSITION

HORIZONTAL CLOCK

CLOCK PHASE

RESET

Automatically adjust the geometry to fit the screen.

Adjust horizontal position.

Adjust vertical position.

Adjusts the dot clock frequency to reduce the vertical stripe.

Adjusts the phase to correct blurred or unstable images.

Recall the factory preset data of the RGB setup settings.

This item only available with an RGB:2 input.

Set the preferred input signal level.

SETUP

RGB2 INPUT

INPUT LEVEL

RGB:2 Digital Input Mode Menu

AUTO ADJUST

H. POSITION

V. POSITION

HORIZONTAL CLOCK

CLOCK PHASE

RESET

Automatically adjust the geometry to fit the screen.

Adjust horizontal position.

Adjust vertical position.

Adjusts the dot clock frequency to reduce the vertical stripe.

Adjusts the phase to correct blurred or unstable images.

Recall the factory preset data of the RGB setup settings.

Select between Mode:1 and Mode:2 input. (RGB:2 Input Only)

Set the preferred input signal level.

RGB2 INPUT

INPUT LEVEL

NOTE:

RGB:1 Input does not have “RGB2 INPUT” feature.

RGB ON SCREEN DISPLAY

The following adjustments are independent of the TV mode:

VIDEO ADJUSTMENTS

•Press MENU in RGB mode for on screen display.

•Press THUMB STICK ̆ or ̄ to highlight the item to be adjusted.

•Press SELECT to select the highlighted item.

This feature allows you to adjust the contrast in RGB mode.

CONTRAST

Use THUMB STICK ̇ or ̈ to adjust contrast.

Press MENU button to return to RGB MODE

MENU and EXIT to quit.

RGB MODE MENU

VIDEO

CONTRAST

50%

BRIGHTNESS

COLOR TEMPERATURE

ENHANCER

50%

MEDIUM

RESET

BLACK SIDE PANEL

EXIT

TO QUIT

CHANGE

MOVE

VALUE

NOTE: See TV contrast feature for additional information regarding contrast.

This feature allows you to adjust brightness in PC Mode.

BRIGHTNESS

Use THUMB STICK ̇ or ̈ to adjust brightness.

Press MENU button to return to RGB MODE MENU and

EXIT to quit.

RGB MODE MENU

VIDEO

CONTRAST

50%

BRIGHTNESS

COLOR TEMPERATURE

ENHANCER

50%

MEDIUM

RESET

BLACK SIDE PANEL

CHANGE

MOVE

EXIT

TO QUIT

VALUE

COLOR

TEMPERATURE

Use the CURSOR to change the COLOR TEMPERATURE. Set this to HIGH for cooler with more

blue (9,300K - 32HDT20; 9,200K - 42HDT20), set to MEDIUM for more natural color (7,500K), or

set to STANDARD for accurate color (6,500K).

RGB MODE MENU

VIDEO

CONTRAST

50%

BRIGHTNESS

COLOR TEMPERATURE

ENHANCER

50%

MEDIUM

RESET

BLACK SIDE PANEL

EXIT

TO QUIT

MOVE

TO CHANGE

RGB ON SCREEN DISPLAY

Enhances the picture detail.

ENHANCER

• Use THUMB STICK ̆, ̄ to set ENHANCER ON or

OFF.

RGB MODE MENU

VIDEO

CONTRAST

50%

BRIGHTNESS

COLOR TEMPERATURE

ENHANCER

50%

• Press SELECT button to ACCEPT and EXIT to quit.

MEDIUM

RESET

BLACK SIDE PANEL

EXIT

TO QUIT

MOVE

TO CHANGE

Set CONTRAST, BRIGHTNESS, COLOR TEMPERATURE, and ENHANCER to factory

preset condition.

RESET

Press down on THUMB STICK to RESET to factory

preset settings.

RGB MODE MENU

VIDEO

CONTRAST

50%

BRIGHTNESS

COLOR TEMPERATURE

ENHANCER

50%

MEDIUM

RESET

BLACK SIDE PANEL

SEL

TO RESET

EXIT

TO QUIT

MOVE

BLACK SIDE

PANEL

The BLACK SIDE PANEL function turns the gray side bars ON/OFF when watching 4:3

signals in Standard Mode.

Press down on THUMB STICK to select BLACK SIDE

PANEL ON/OFF.

RGB MODE MENU

VIDEO

CONTRAST

50%

BRIGHTNESS

50%

COLOR TEMPERATURE

MEDIUM

ENHANCER

RESET

BLACK SIDE PANEL

SEL

ON/OFF

EXIT

TO QUIT

MOVE

NOTE:

To prevent the plasma phosphor from burning when watching 4:3 signal, turn off the BLACK SIDE PANEL. It is

recommended to watch 4:3 signal with gray side bar.

RGB ON SCREEN DISPLAY

HORIZONTAL POSITION, VERTICAL POSITION, HORIZONTAL CLOCK and CLOCK PHASE

for current RGB format are adjusted automatically.

AUTO ADJUST

RGB MODE MENU

SET UP

Press SELECT to select AUTO ADJUST.

AUTO ADJUST

H POSITION

V POSITION

HORIZONTAL CLOCK

CLOCK PHASE

RESET

+22

RGB2 INPUT

INPUT LEVEL

MODE:1

0.7V

EXIT

SEL

TO QUIT

MOVE

TO START

NOTE: • Press SELECT to AUTO ADJUST the RGB mode.

• The other functions do not operate while AUTO ADJUST is in progress.

• Allow the Plasma TV to warm up for 20 minutes before performing AUTO ADJUST.

• Select a bright image for display while AUTO ADJUST takes place.

• If AUTO ADJUST terminates unsuccessfully, try AUTO ADJUST again. If AUTO ADJUST fails several times in

succession, try using manual adjustment.

• Always reset AUTO ADJUST when setting new display setting or when changing to a new

external component.

This feature allows you to adjust the horizontal position of the display.

H POSITION

Use Left/Right cursors to adjust the horizontal position.

RGB MODE MENU

Press the MENU button to return to previous menu item.

SET UP

AUTO ADJUST

H POSITION

V POSITION

HORIZONTAL CLOCK

CLOCK PHASE

RESET

Press EXIT to quit.

+22

RGB2 INPUT

INPUT LEVEL

MODE:1

0.7V

EXIT

CHANGE

VALUE

MOVE

TO QUIT

This feature allows you to adjust the vertical position in RGB mode.

V POSITION

Use THUMB STICK ̇, ̈ to adjust the vertical

position.

RGB MODE MENU

Press MENU button to return to previous menu item.

Press EXIT to quit.

AUTO ADJUST

H POSITION

V POSITION

HORIZONTAL CLOCK

CLOCK PHASE

RESET

+22

RGB2 INPUT

INPUT LEVEL

MODE:1

0.7V

EXIT

CHANGE

MOVE

VALUE

TO QUIT

RGB ON SCREEN DISPLAY

Adjusts the pixel clock frequency to reduce the vertical stripe.

HORIZONTAL CLOCK

Use THUMB STICK ̇, ̈ to adjust the horizontal

clock. Press the MENU button to return to previous

menu. Press EXIT to quit.

RGB MODE MENU

SET UP

AUTO ADJUST

H POSITION

V POSITION

HORIZONTAL CLOCK

CLOCK PHASE

RESET

+22

RGB2 INPUT

INPUT LEVEL

MODE:1

0.7V

EXIT

CHANGE

VALUE

MOVE

TO QUIT

NOTE:

Due to varying signal content, you may see vertical or horizontal lines bend occasionally in RGB mode. However, this

phenomenon is not a defect. It’s caused by a lack of picture content due to under-scanning in RGB mode.

Adjusts the phase to correct blurred or unstable images.

CLOCK PHASE

Use THUMB STICK ̇, ̈ to adjust the clock phase.

Press the MENU button to return to previous menu item.

Press EXIT to quit.

RGB MODE MENU

SET UP

AUTO ADJUST

H POSITION

V POSITION

HORIZONTAL CLOCK

CLOCK PHASE

RESET

+22

RGB2 INPUT

MODE:1

0.7V

INPUT LEVEL

EXIT

CHANGE

VALUE

MOVE

TO QUIT

Set HORIZONTAL POSITION, VERTICAL POSITION, HORIZONTAL CLOCK and CLOCK

PHASE to factory preset, for current RGB format.

RESET

RGB MODE MENU

SET UP

Press down on THUMB STICK to RESET to factory

preset settings.

AUTO ADJUST

H POSITION

V POSITION

HORIZONTAL CLOCK

CLOCK PHASE

RESET

+22

RGB2 INPUT

INPUT LEVEL

SEL

MODE:1

0.7V

EXIT

TO QUIT

MOVE

TO RESET

RGB ON SCREEN DISPLAY

This feature allows you to select between Mode A and Mode B depending on signal input to

RGB2 Input, depending on your preference.

RGB2 INPUT

Use THUMB STICK ̇, ̈ to toggle between Mode 1

or Mode 2 signal input to RGB2 Input.

RGB MODE MENU

SET UP

AUTO ADJUST

H POSITION

V POSITION

HORIZONTAL CLOCK

CLOCK PHASE

RESET

+22

NOTE:

This feature is only available in RGB:2 input. See

page 29 for signal type for Mode 1 and Mode 2

RGB2 INPUT

INPUT LEVEL

MODE:1

0.7V

EXIT

CHANGE

VALUE

MOVE

TO QUIT

RGB1/RGB2 ASPECT DISPLAY MODE.

RGB1 INPUT SIGNAL

RGB2 INPUT SIGNAL

MODE 1

MODE 2

VGA

480p

720p

1080i

VGA

480p

720p

1080i

VGA

480p

720p

1080i

ASPECT

MODE

REAL

REAL(1)

REAL

NORMAL

NORMAL NORMAL NORMAL(1)

AVAILABILITY FULL

NORMAL NORMAL NORMAL

FULL

FULL (1) FULL (2) FULL (2)

FULL FULL (3) FULL (2) FULL (2) FULL

FULL FULL (2) FULL (2) FULL (2)

For numbers in ( ), please see corresponding note below.

NOTES: 1. Lack of raster can be seen in RGB1 when a 480p signal is input.

2. AUTO ADJUST function (see page 72) is not available in 720p, 1080i, and (480p/VGA~RGB2 Mode 2 only) input signal.

3. Horizontal Phase is shifted in RGB2 when 480p signal is input.

4. All FULL aspect mode, only 95% of information can be displayed (5% is treated as overscan).

Select the Input Level voltage between 0.7V and 1.0V.

INPUT LEVEL

RGB MODE MENU

SET UP

Use THUMB STICK ̇, ̈ to select between 0.7V and

1.0V depending on the amount of brightness in the

picture.

AUTO ADJUST

H POSITION

V POSITION

HORIZONTAL CLOCK

CLOCK PHASE

RESET

+22

RGB2 INPUT

MODE:1

INPUT LEVEL

0.7V

EXIT

CHANGE

VALUE

MOVE

TO QUIT

CARE OF YOUR HITACHI PLASMA DISPLAY

AND YOUR REMOTE CONTROL

Dust the screen with a soft cloth.

Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if

the screen is extremely dirty.

Place your Plasma Television away from extreme heat, humidity, and extremely dusty places.

Remove the plug (AVC Center/Display Monitor) from the wall outlet if your Plasma Television will not be used for

a long period of time, for instance, when you go on vacation.

DO NOT

Do not clean your screen with strong cleaners, polishes or a chemically treated cloth.

Do not place rubber or vinyl products or cellophane tape on your Plasma Television.

Avoid repeatedly touching the screen.

Do not subject the remote control to shocks such as dropping it on the floor, etc. This may cause physical damage

to the precision parts.

Avoid placing the remote control in a high humidity place or getting it wet. Do not leave it on or near a heater.

Excessive heat or moisture may cause the remote control unit to fail.

When the batteries run down, remote control operation will become erratic or become unresponsive. Replace the old

batteries with two new “AA” size batteries. Do not use an old battery with a new battery.

Exposing the screen to direct sunlightfor a long period of time or heat may cause damage to the plasma screen.

USEFUL INFO

• IGNITION NOISE:

Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by

interference from automobile ignition systems, neon lamps, electrical drills, and other electrical

appliances.

• GHOSTS:

Ghosts are caused by the television signal following two paths. One is the direct path and the

other is reflected from tall buildings, hills or some other objects. Changing the direction or posi-

tion of the antenna may improve reception. Ghosting may also be caused by defects in the

antenna system such as unshielded leads or connecting several sets to the same antenna with-

out using multiple antenna couplers.

• SNOW:

If your receiver is located in the fringe area of a television station where the signal is weak, your

picture may be marred by the appearance of small dots. When the signal is extremely weak, it

may be necessary to install a special antenna to improve the picture.

• RADIO FREQUENCY INTERFERENCE:

The interference produces moving ripples or diagonal streaks, and in some cases, causes loss

of contrast in the picture.

• PREVENTION OF AN OBSTACLE TO RADIO RECEIVERS

This monitor has been designed pursuant to the FCC class B Rules. This is to prevent a prob-

lem to Radio receivers. If this monitor causes a problem to Radio receivers, then take the follow-

ing steps:

- Keep the monitor away from Radio.

- Adjust Radio antennas in order for the monitor not to receive

interference.

- The antenna cable of Radio should be kept away from the monitor.

- Use a coaxial cable for antenna.

You can check if this monitor influences Radio receivers by turning off all other equipment other

than the monitor.

If you find a problem receiveing Radio when using the monitor, check the instructions mentioned

above.

• Adjust the dot clock frequency and phase.

(Adjust the dot clock frequency first, the dot clock

phase next.)

• The display image appears

scrolling diagonal.

• Text displayed across the

screen appears vertically

streaked, with the characters

in vertical columns blurred.

(RGB input)

• Adjust the dot clock phase for the clearest

viewing.

(RGB input)

• Text displayed across the

screen appears blurred.

• A fine pattern flickers when

displayed on the screen.

• Vertical stripes appear, depending on the • The plasma display panel is lighting the

screen contents.

phosphors by the discharge of internal

radiation. Depending on the screen

contents, in rare cases this may cause

vertical stripes to appear because of failure

to light. Please note that this is not a

malfunction.

• Coarse horizontal stripes appear in FULL • Adjusting the phase will reduce the

display.

horizontal stripes.

(RGB input)

• This condition may occur when the unit is

connected to a VCR with component output,

such as 480i, but it is not a failure. But when

it occurs, switch to composite output or S1

(S2) output).

• The display dims to make the picture

invisible during special playback of a

VCR (FF, REW).

USEFUL INFO

SYMPTOMS

No Picture, no sound

Sound OK, picture poor

Picture OK, sound poor

Picture blurred

Lines or streaks in picture

Poor reception on some channels

Picture rolls vertically

No color

Poor color

PLUG and PLAY

This Plasma Television complies with VESA DDC2B specifications, Plug & Play

is a system with computer, peripherals (including monitors) and operating sys-

tem. It works when the monitor is connected to a DDC ready computer that is

running an operating system software that is capable for the plug & play.

When a Plug and Play PC is powered on, it sends a command to the Monitor

requesting identification. The Monitor sends back a string of data including its

characteristics.

TRADEMARK ACKNOWLEDGMENT

DDC^TMis a trademark of Video Electronics Standard Association.

IBM PC/AT and VGA are registered trademarkds of International Business Machines Corporation of the U.S.A.

Apple and Macintosh are registered trademarks of Apple Computer, Inc.

VESA is a trademark of a nonprofit organization, Video Electronics Standard Association.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Cable Compatible Television Apparatus- Tèlèvision câblocompatible, Canada.

Notes on Closed Caption:

This Plasma Television receiver will display television closed captioning, (

15.119 of the FCC rules.

), in accordance with paragraph

RGB ON SCREEN DISPLAY

AGENCY REGULATORY

INFORMATION

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not express-

ly approved by Hitachi Home Electronics (America), Inc. may void the user’s warranty.

Cables

Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain com-

pliance with FCC Rules and Regulations.

Any cables that are supplied with the system must be replaced with identical cables in order to assure compliance with

FCC rules. Order Hitachi spares as replacement cables.

Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference and (2) this device must accept any interference received, including interference

that may cause undesired operation.

For questions regarding this declaration, contact:

Hitachi America, LTD.

Home Electronics Division

1855 Dornoch Court

San Diego, CA 92154

Tel. 1-800-448-2244 (1-800-HITACHI)

ATTN: CUSTOMER RELATIONS

USEFUL INFO

Audio:

Features:

•

MTS Stereo/SAP

TruBass and Matrix Surround

10W+10W (42HDT20)

7W+ 7W (32HDT20)

Soft Mute (50% and 100%)

•

New Easy-to-Use On-Screen Menu Control (3 Language)

New AV Network System Control

Control up to 4 components with one remote

2 IR Mouse cables included

Control Codes Stored in AV Control Center

Two Tuner Split Screen except RGB modes.

Illuminated and Preprogrammed Remote Control

Power Management: ON/OFF via signal detection

Menu Control Keys accessible from AV Control Center

Picture Enhancement

•

Supplied Accesories:

•

Illuminated Preprogrammed Remote Control

Batteries

9’ Monitor Connection Cable

6’ AC Cable (2)

Input Signal Indentification

Video:

Optional Accesories:

•

1024 x 1024 Display Resolution (42HDT20)

•

32’ Monitor Connection Cable

852 x 1024 Display Resolution (32HDT20)

ALiS (Alternate Lighting of Surfaces Technology)

High-Contrast Pure-Color Glass Shield

•

Wall Mount Bracket

INPUTS/OUTPUTS

•

Inputs: ......................................RGB 1/2, VIDEO 1-5

Wideband Component Y, Pb,Pr ............................................2

RGB1: Analog Input ..............................................................1

RGB2: Digital Input ...............................................................1

Composite Video...................................................................4

S-Video .................................................................................3

Antenna (RF) Inputs..............................................................2

Converter Box Output ...........................................................1

Audio Output.........................................................................1

Monitor Output ......................................................................1

Headphone Output................................................................1

Subwoofer Output.................................................................1

Wide Viewing Angle: More than 160˚

3 Color Temperature Presets: Standard-6500K, Medium-

7500K, High-9300K (32HDT20), 9200K (42HDT20)

Multiple Screen Fill Modes (4:3 Standard/Expanded/Zoom1/

Zoom2/16:9 Standard)¹

•

4MB 10-bit 3D Y/C Comb Filter

Picture Modes (Sports, Movies, News, Music)

Computer Display: VGA, (SVGA, XGA, SXGA-scaled)

Inputs:

•

Power Input . . . . . . . . . . . . .AC 120V, 60Hz

Power Consumption

SPECIFICATIONS

- Refer to rear panel at the back of the Plasma

Monitor and AVC Center

•

Multi-Scanning: ................24-109kHz (h), 50-85Hz (v)

Pixel Pitch(42HDT20) .....0.90(horiz.) x 0.51(vert.) mm

Pixel Pitch(32HDT20) .....0.84(horiz.) x 0.39(vert.) mm

FCC class: .................................B for Consumer Use

Power Requirements: ........................108-132V, 60Hz

•

Antenna input impedance . . . . . . . . .75 Ohm

Channel coverage . . . . . . . . . . . . . . .181ch.

VHF-Band . . . . . . . . . . . . . . . . . . . . .2 ~ 13

UHF-Band . . . . . . . . . . . . . . . . . . . .14 ~ 69

CATV Mid Band . . . . . . . . . . . . . . .A-5 ~ A-1

. . . . . . . . . . . . . . . . . . . . . . . . . . .A-I

DIMENSIONS

Monitor without stand

42HDT20

40 9/16”

25 1/16”

3 9/16”

32HDT20

38 3/8”

19 3/4”

3 9/16”

58 lbs.

Super Band . . . . . . . . . . . . . . . . . . . . .J-W

Hyper Band . . . . . . . . . . . . . . .W+1 - W+28

Ultra Band . . . . . . . . . . . . . . .W+29 - W+84

Video . . . . . . . . . . . . . . . .1.0Vp-p, 75 Ohm

•

Width

Height

Depth

Weight

•

86 lbs.

(incl. stand & speakers)

S-Video

Luminance (Y) . . . . . . . . . .1.0Vp-p, 75 Ohm

Chrominance (C) . . . . . .0.286Vp-p, 75 Ohm

Audio Video Control Center

•

Width .........................................................16 15/16”

Height..............................................................4 3/4”

Depth ...........................................................11 1/16”

Weight..............................................................9 lbs.

•

Component Video

Luminance (Y) . . . . . . . . . . . . . . .1.0Vp-p, 75 Ohm

Chrominance (P /P ) . . . . . . . . .0.7Vp-p, 75 Ohm

•

Audio input Impedence . . . . . . . . . .47k Ohm

•

Average input level . . . . . . . . . . . . . . . .470mVrms

RGB1 . . . . . . . . . . . . . . . . . . . . .0.7Vp-p, 75 Ohm

Screen mode availability varies by input format

HDTV Monitors display HDTV when combined with an HDTV Tuner and Source.

All specifications, weights, and dimenions are subject to change without prior notice.

Please access www.hitachi.com/tv for detailed specifications and imensions for cus-

tom installations.

RGB2

Mode 1 . . . . . . . . . . . . .0.7Vp-p, 75 Ohm

Mode 2 . . . . . . . . . . . . .1.0Vp-p, 75 Ohm

Outputs:

UltraVision Digital is a registered trademark of Hitachi Home Electronics (America),

Inc.

•

Video . . . . . . . . . . . . . . . . . . . . .1.0Vp-p. 75 Ohm

Audio . . . . . . . . . . . . . . . . . . .470mVrms, 1k Ohm

TruBass and the SRS

technology is incorporated under license from SRS Labs, Inc.

symbol are trademarks of SRS Labs, Inc. TruBass

USEFUL INFO

To locate an authorized

HITACHI service facility

in the continental U.S.A.

and Canada,

DIAL TOLL FREE

service

7 days a week, 24 hours a day

8 0 0 HITACHI

(1-800-448-2244)

Hitachi America, LTD.

Home Electronics Division

Hitachi has made every effort to assure you hours of trouble free operation from your unit. However, should you require service,

a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico. Each facility will provide

you with convenient and expedient assistance. Our service hotline operator will direct you to the Hitachi Authorized Service

Facility nearest you. Just present proof of purchase and/or delivery receipts to the Hitachi Authorized Service Facility, and serv-

ice will be rendered in accordance with the terms of the limited warranty as stated on your warranty card or operating guide.

Should you have any questions regarding warranty, service, operation, or technical assistance, please c

ontact:

Hitachi America, LTD.

Home Electronics Division

1855 Dornoch Court

San Diego, CA 92154

USEFUL INFO

Hitachi Canada, LTD.

Digital Media Division

Should you have any questions regarding warranty, service, operation, or technical assistance, please

contact:

In Canada:

1-800-HITACHI

(1-800-448-2244)

Monday - Friday EST 9:00am - 7:00pm

Saturday EST 9:00am - 5:00pm

Look for your French Manual on the outside of the box.

If the manual is missing, call

1-800-HITACHI

(1-800-448-2244)

for a copy.

Pour de plus amples renseignements sur le service durant la période couverte par la garantie, sur le fonc-

tionnement ou pour de l’assistance technique communiquez avec:

Au Canada:

1-800-HITACHI

(1-800-448-2244)

Lundi - Vendredi L’EST 9:00am - 7:00pm

Samedi L’EST 9:00am - 5:00pm

La version française de votre manual se trouve á l’extérieur de la boîte.

Si le manuel est manquant, coposez le

1-800-HITACHI

(1-800-448-2244)

pour obenir votre copie.

HITACHI CANADA, LTD.

6760 Campobello Road

Mississauga, ON L5N 2L8

NOTES

QR52141

York H Re024 User Manual
Worth Data 701 Rf User Manual
Sharp Ar 407 User Manual
Sharp Al 841 User Manual
Philips Scb2025nb User Manual
Lexmark 13b4058 User Manual
KENWOOD KRF V5060DE User Manual
EPSON BRIGHTLINK 455WI 02 User Manual
DANFOSS 103 User Manual
BLUSTREAM PLA88ARC User Manual